OSDN Git Service
David S. Miller [Tue, 23 Jan 2018 18:49:06 +0000 (13:49 -0500)]
Merge git://git./linux/kernel/git/davem/net
en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.
The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 23 Jan 2018 16:52:55 +0000 (08:52 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix divide by zero in mlx5, from Talut Batheesh.
2) Guard against invalid GSO packets coming from untrusted guests and
arriving in qdisc_pkt_len_init(), from Eric Dumazet.
3) Similarly add such protection to the various protocol GSO handlers.
From Willem de Bruijn.
4) Fix regression added to IGMP source address checking for IGMPv3
reports, from Felix Feitkau.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tls: Correct length of scatterlist in tls_sw_sendpage
be2net: restore properly promisc mode after queues reconfiguration
net: igmp: fix source address check for IGMPv3 reports
gso: validate gso_type in GSO handlers
net: qdisc_pkt_len_init() should be more robust
ibmvnic: Allocate and request vpd in init_resources
ibmvnic: Revert to previous mtu when unsupported value requested
ibmvnic: Modify buffer size and number of queues on failover
rds: tcp: compute m_ack_seq as offset from ->write_seq
usbnet: silence an unnecessary warning
cxgb4: fix endianness for vlan value in cxgb4_tc_flower
cxgb4: set filter type to 1 for ETH_P_IPV6
net/mlx5e: Fix fixpoint divide exception in mlx5e_am_stats_compare
Xin Long [Tue, 23 Jan 2018 10:22:25 +0000 (18:22 +0800)]
sctp: reset ret in again path in sctp_for_each_transport
Commit
97a6ec4ac021 ("rhashtable: Change rhashtable_walk_start to
return void") only initialized ret for the first time, when going
to again path, the next tsp could be NULL. Without resetting ret,
cb_done would be called with tsp as NULL.
A kernel crash was caused by this when running sctpdiag testcase
in sctp-tests.
Note that this issue doesn't affect net.git yet.
Fixes:
97a6ec4ac021 ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 23 Jan 2018 09:44:08 +0000 (09:44 +0000)]
bnx2: remove redundant initializations of pointers txr and rxr
Pointers txr and rxr are being initialized and a few statements later
are being assigned new values without the original values ever being
read. The initialized values are therefore redundant and can be
removed.
Cleans up clang warnings:
drivers/net/ethernet/broadcom/bnx2.c:5821:28: warning: Value stored to
'txr' during its initialization is never read
drivers/net/ethernet/broadcom/bnx2.c:5822:28: warning: Value stored to
'rxr' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yanjun [Tue, 23 Jan 2018 07:03:37 +0000 (02:03 -0500)]
forcedeth: remove duplicate structure member in rx
Since both first_rx_ctx and rx_skb are the head of rx ctx, it not
necessary to use two structure members to statically indicate
the head of rx ctx. So first_rx_ctx is removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 23 Jan 2018 16:06:51 +0000 (11:06 -0500)]
Merge branch 'Kernel-doc-fixes-for-networking'
Florian Fainelli says:
====================
Kernel doc fixes for networking
This patch series fixes kernel doc warnings found while running make htmldocs
pertaining to the networking subsystem. There is a finaly set of warnings due
to PHYLINK which I have not been able to resolve yet.
The last patch could thereoteically be applied to 'net' since the commit
referenced by the Fixes: tag is present in v4.15-rcX.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 23 Jan 2018 03:14:28 +0000 (19:14 -0800)]
net: core: Fix kernel-doc for netdev_upper_link()
Fixes the following warnings:
./net/core/dev.c:6438: warning: No description found for parameter 'extack'
./net/core/dev.c:6461: warning: No description found for parameter 'extack'
Fixes:
42ab19ee9029 ("net: Add extack to upper device linking")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 23 Jan 2018 03:14:27 +0000 (19:14 -0800)]
net: core: Fix kernel-doc for call_netdevice_notifiers_info()
Remove the @dev comment, since we do not have a net_device argument, fixes the
following kernel doc warning: /net/core/dev.c:1707: warning: Excess function
parameter 'dev' description in 'call_netdevice_notifiers_info'
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 23 Jan 2018 03:14:26 +0000 (19:14 -0800)]
net: phy: sfp: Fix kernel doc warning
We forgot to update the kernel doc header above sfp_register_upstream()
Fixes:
c19bb00070dd ("sfp: convert to fwnode")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 23 Jan 2018 03:14:25 +0000 (19:14 -0800)]
net: core: Fix kernel-doc for carrier_* attributes
Fix the documentation warning:
include/linux/netdevice.h:1939: warning: Excess struct member 'carrier_changes' description in 'net_device'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes:
b2d3bcfa26a7 ("net: core: Expose number of link up/down transitions")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 23 Jan 2018 02:10:38 +0000 (02:10 +0000)]
net: aquantia: make symbol hw_atl_boards static
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:50:34: warning:
symbol 'hw_atl_boards' was not declared. Should it be static?
Fixes:
4948293ff963 ("net: aquantia: Introduce new AQC devices and capabilities")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 23 Jan 2018 02:10:46 +0000 (02:10 +0000)]
net: aquantia: Fix error return code in aq_pci_probe()
Fix to return error code -ENOMEM from the aq_ndev_alloc() error
handling case instead of 0, as done elsewhere in this function.
Fixes:
23ee07ad3c2f ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 23 Jan 2018 02:10:27 +0000 (02:10 +0000)]
nfp: fix error return code in nfp_pci_probe()
Fix to return error code -EINVAL instead of 0 when num_vfs above
limit_vfs, as done elsewhere in this function.
Fixes:
0dc786219186 ("nfp: handle SR-IOV already enabled when driver is probing")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carl Heymann [Tue, 23 Jan 2018 01:29:43 +0000 (17:29 -0800)]
nfp: fix fw dump handling of absolute rtsym size
Fix bug that causes _absolute_ rtsym sizes of > 8 bytes (as per symbol
table) to result in incorrect space used during a TLV-based debug dump.
Detail: The size calculation stage calculates the correct size (size of
the rtsym address field == 8), while the dump uses the size in the table
to calculate the TLV size to reserve. Symbols with size <= 8 are handled
OK due to aligning sizes to 8, but including any absolute symbol with
listed size > 8 leads to an ENOSPC error during the dump.
Fixes:
da762863edd9 ("nfp: fix absolute rtsym handling in debug dump")
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 22 Jan 2018 20:11:06 +0000 (20:11 +0000)]
nfsd: auth: Fix gid sorting when rootsquash enabled
Commit
bdcf0a423ea1 ("kernel: make groups_sort calling a responsibility
group_info allocators") appears to break nfsd rootsquash in a pretty
major way.
It adds a call to groups_sort() inside the loop that copies/squashes
gids, which means the valid gids are sorted along with the following
garbage. The net result is that the highest numbered valid gids are
replaced with any lower-valued garbage gids, possibly including 0.
We should sort only once, after filling in all the gids.
Fixes:
bdcf0a423ea1 ("kernel: make groups_sort calling a responsibility ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cong Wang [Mon, 22 Jan 2018 21:49:27 +0000 (13:49 -0800)]
tun: avoid calling xdp_rxq_info_unreg() twice
Similarly to tx ring, xdp_rxq_info is only registered
when !tfile->detached, so we need to avoid calling
xdp_rxq_info_unreg() twice too. The helper tun_cleanup_tx_ring()
already checks for this properly, so it is correct to put
xdp_rxq_info_unreg() just inside there.
Reported-by: syzbot+1c788d7ce0f0888f1d7f@syzkaller.appspotmail.com
Fixes:
8565d26bcb2f ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Brandenburg [Mon, 22 Jan 2018 20:44:52 +0000 (15:44 -0500)]
orangefs: initialize op on loop restart in orangefs_devreq_read
In orangefs_devreq_read, there is a loop which picks an op off the list
of pending ops. If the loop fails to find an op, there is nothing to
read, and it returns EAGAIN. If the op has been given up on, the loop
is restarted via a goto. The bug is that the variable which the found
op is written to is not reinitialized, so if there are no more eligible
ops on the list, the code runs again on the already handled op.
This is triggered by interrupting a process while the op is being copied
to the client-core. It's a fairly small window, but it's there.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Martin Brandenburg [Mon, 22 Jan 2018 20:44:51 +0000 (15:44 -0500)]
orangefs: use list_for_each_entry_safe in purge_waiting_ops
set_op_state_purged can delete the op.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Mon, 22 Jan 2018 21:30:30 +0000 (16:30 -0500)]
Merge branch 'net-sched-add-extack-support-for-cls-offloads'
Jakub Kicinski says:
====================
net: sched: add extack support for cls offloads
I've dropped the tests from the series because test_offloads.py changes
will conflict with bpf-next patches. I will send four more patches with
tests once bpf-next is merged back, hopefully still making it into 4.16 :)
v4:
- rebase on top of Alex's changes.
---
Quentin says:
This series tries to improve user experience when eBPF hardware offload
hits error paths at load time. In particular, it introduces netlink
extended ack support in the nfp driver.
To that aim, transmission of the pointer to the extack object is piped
through the `change()` operation of the existing classifiers (patch 1 to
6). Then it is used for TC offload in the nfp driver (patch 8) and in
netdevsim (patch 9, selftest in patch 10). Patch 7 adds a helper to handle
extack messages in the core when TC offload is disabled on the net device.
For completeness extack is propagated for classifiers other than cls_bpf,
but it's up to the drivers to make use of it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Sat, 20 Jan 2018 01:44:50 +0000 (17:44 -0800)]
nfp: bpf: use extack support to improve debugging
Use the recently added extack support for eBPF offload in the driver.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Sat, 20 Jan 2018 01:44:49 +0000 (17:44 -0800)]
nfp: bpf: plumb extack into functions related to XDP offload
Pass a pointer to an extack object to nfp_app_xdp_offload() in order to
prepare for extack usage in the nfp driver. Next step will be to forward
this extack pointer to nfp_net_bpf_offload(), once this function is able
to use it for printing error messages.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Sat, 20 Jan 2018 01:44:48 +0000 (17:44 -0800)]
net: sched: create tc_can_offload_extack() wrapper
Create a wrapper around tc_can_offload() that takes an additional
extack pointer argument in order to output an error message if TC
offload is disabled on the device.
In this way, the error message is handled by the core and can be the
same for all drivers.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Sat, 20 Jan 2018 01:44:47 +0000 (17:44 -0800)]
net: sched: add extack support for offload via tc_cls_common_offload
Add extack support for hardware offload of classifiers. In order
to achieve this, a pointer to a struct netlink_ext_ack is added to the
struct tc_cls_common_offload that is passed to the callback for setting
up the classifier. Function tc_cls_common_offload_init() is updated to
support initialization of this new attribute.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Sat, 20 Jan 2018 01:44:46 +0000 (17:44 -0800)]
net: sched: cls_bpf: plumb extack support in filter for hardware offload
Pass the extack pointer obtained in the `->change()` filter operation to
cls_bpf_offload() and then to cls_bpf_offload_cmd(). This makes it
possible to use this extack pointer in drivers offloading BPF programs
in a future patch.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Sat, 20 Jan 2018 01:44:45 +0000 (17:44 -0800)]
net: sched: cls_u32: propagate extack support for filter offload
Propagate the extack pointer from the `->change()` classifier operation
to the function used for filter replacement in cls_u32. This makes it
possible to use netlink extack messages in the future at replacement
time for this filter, although it is not used at this point.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Sat, 20 Jan 2018 01:44:44 +0000 (17:44 -0800)]
net: sched: cls_matchall: propagate extack support for filter offload
Propagate the extack pointer from the `->change()` classifier operation
to the function used for filter replacement in cls_matchall. This makes
it possible to use netlink extack messages in the future at replacement
time for this filter, although it is not used at this point.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Sat, 20 Jan 2018 01:44:43 +0000 (17:44 -0800)]
net: sched: cls_flower: propagate extack support for filter offload
Propagate the extack pointer from the `->change()` classifier operation
to the function used for filter replacement in cls_flower. This makes it
possible to use netlink extack messages in the future at replacement
time for this filter, although it is not used at this point.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Watson [Fri, 19 Jan 2018 20:30:13 +0000 (12:30 -0800)]
tls: Correct length of scatterlist in tls_sw_sendpage
The scatterlist is reused by both sendmsg and sendfile.
If a sendmsg of smaller number of pages is followed by a sendfile
of larger number of pages, the scatterlist may be too short, resulting
in a crash in gcm_encrypt.
Add sg_unmark_end to make the list the correct length.
tls_sw_sendmsg already calls sg_unmark_end correctly when it allocates
memory in alloc_sg, or in zerocopy_from_iter.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 19 Jan 2018 20:26:43 +0000 (13:26 -0700)]
hv_netvsc: Use the num_online_cpus() for channel limit
Since we no longer localize channel/CPU affiliation within one NUMA
node, num_online_cpus() is used as the number of channel cap, instead of
the number of processors in a NUMA node.
This patch allows a bigger range for tuning the number of channels.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Fri, 19 Jan 2018 19:23:50 +0000 (20:23 +0100)]
be2net: restore properly promisc mode after queues reconfiguration
The commit
622190669403 ("be2net: Request RSS capability of Rx interface
depending on number of Rx rings") modified be_update_queues() so the
IFACE (HW representation of the netdevice) is destroyed and then
re-created. This causes a regression because potential promiscuous mode
is not restored properly during be_open() because the driver thinks
that the HW has promiscuous mode already enabled.
Note that Lancer is not affected by this bug because RX-filter flags are
disabled during be_close() for this chipset.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes:
622190669403 ("be2net: Request RSS capability of Rx interface depending on number of Rx rings")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta [Fri, 19 Jan 2018 15:20:53 +0000 (15:20 +0000)]
net: hns3: converting spaces into tabs to avoid checkpatch.pl warning
Spaces were mistakenly used instead of tabs in some of the code related
to reset functionality, which caused checkpatch.pl errors. These were
missed earlier so fixing them now.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Fri, 19 Jan 2018 10:50:46 +0000 (11:50 +0100)]
net: igmp: fix source address check for IGMPv3 reports
Commit "net: igmp: Use correct source address on IGMPv3 reports"
introduced a check to validate the source address of locally generated
IGMPv3 packets.
Instead of checking the local interface address directly, it uses
inet_ifa_match(fl4->saddr, ifa), which checks if the address is on the
local subnet (or equal to the point-to-point address if used).
This breaks for point-to-point interfaces, so check against
ifa->ifa_local directly.
Cc: Kevin Cernekee <cernekee@chromium.org>
Fixes:
a46182b00290 ("net: igmp: Use correct source address on IGMPv3 reports")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun Vynipadath [Fri, 19 Jan 2018 09:41:48 +0000 (15:11 +0530)]
cxgb3: assign port id to net_device->dev_port
T3 devices have different ports on same PCI function,
so using dev_port to identify ports.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Thu, 18 Jan 2018 23:37:45 +0000 (17:37 -0600)]
bridge: return boolean instead of integer in br_multicast_is_router
Return statements in functions returning bool should use
true/false instead of 1/0.
This issue was detected with the help of Coccinelle.
Fixes:
85b352693264 ("bridge: Fix build error when IGMP_SNOOPING is not enabled")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 18 Jan 2018 23:12:21 +0000 (15:12 -0800)]
net: stmmac: Fix reception of Broadcom switches tags
Broadcom tags inserted by Broadcom switches put a 4 byte header after
the MAC SA and before the EtherType, which may look like some sort of 0
length LLC/SNAP packet (tcpdump and wireshark do think that way). With
ACS enabled in stmmac the packets were truncated to 8 bytes on
reception, whereas clearing this bit allowed normal reception to occur.
In order to make that possible, we need to pass a net_device argument to
the different core_init() functions and we are dependent on the Broadcom
tagger padding packets correctly (which it now does). To be as little
invasive as possible, this is only done for gmac1000 when the network
device is DSA-enabled (netdev_uses_dsa() returns true).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Jan 2018 21:05:50 +0000 (16:05 -0500)]
Merge branch 'hns3-new-features'
Peng Li says:
====================
add some features to hns3 driver
This patchset adds some features to hns3 driver, include the support
for ethtool command -d, -p and support for manager table.
[Patch 1/4] adds support for ethtool command -d, its ops is get_regs.
driver will send command to command queue, and get regs number and
regs value from command queue.
[Patch 2/4] adds manager table initialization for hardware.
[Patch 3/4] adds support for ethtool command -p. For fiber ports, driver
sends command to command queue, and IMP will write SGPIO regs to control
leds.
[Patch 4/4] adds support for net status led for fiber ports. Net status
include port speed, total rx/tx packets and link status. Driver send
the status to command queue, and IMP will write SGPIO to control leds.
---
Change log:
V1 -> V2:
1, fix comments from Andrew Lunn, remove the patch "net: hns3: add
ethtool -p support for phy device".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 19 Jan 2018 06:41:12 +0000 (14:41 +0800)]
net: hns3: add net status led support for fiber port
Check the net status per second, include port speed, total rx/tx packets
and link status. Updating the led status for fiber port.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 19 Jan 2018 06:41:11 +0000 (14:41 +0800)]
net: hns3: add ethtool -p support for fiber port
Add led location support for fiber port. The led will keep blinking
when locating.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fuyun Liang [Fri, 19 Jan 2018 06:41:10 +0000 (14:41 +0800)]
net: hns3: add manager table initialization for hardware
The manager table is empty by default. If it is not initialized, the
management pkgs like LLDP will be dropped by hardware. Default entries
need to be added to manager table.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fuyun Liang [Fri, 19 Jan 2018 06:41:09 +0000 (14:41 +0800)]
net: hns3: add support for get_regs
This patch adds get_regs support for ethtool cmd.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 19 Jan 2018 14:29:18 +0000 (09:29 -0500)]
gso: validate gso_type in GSO handlers
Validate gso_type during segmentation as SKB_GSO_DODGY sources
may pass packets where the gso_type does not match the contents.
Syzkaller was able to enter the SCTP gso handler with a packet of
gso_type SKB_GSO_TCPV4.
On entry of transport layer gso handlers, verify that the gso_type
matches the transport protocol.
Fixes:
90017accff61 ("sctp: Add GSO support")
Link: http://lkml.kernel.org/r/<001a1137452496ffc305617e5fe0@google.com>
Reported-by: syzbot+fee64147a25aecd48055@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 19 Jan 2018 03:59:19 +0000 (19:59 -0800)]
net: qdisc_pkt_len_init() should be more robust
Without proper validation of DODGY packets, we might very well
feed qdisc_pkt_len_init() with invalid GSO packets.
tcp_hdrlen() might access out-of-bound data, so let's use
skb_header_pointer() and proper checks.
Whole story is described in commit
d0c081b49137 ("flow_dissector:
properly cap thoff field")
We have the goal of validating DODGY packets earlier in the stack,
so we might very well revert this fix in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Reported-by: syzbot+9da69ebac7dddd804552@syzkaller.appspotmail.com
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Jan 2018 20:46:56 +0000 (15:46 -0500)]
Merge branch 'ibmvnic-reset-behavior-fixes'
John Allen says:
====================
ibmvnic: Reset behavior fixes
This patchset fixes a number of issues related to ibmvnic reset uncovered
from testing new Power9 machines with Everglades adapters and the new
functionality to change mtu and other parameters in the driver.
Changes since v1:
-In patch 1/3, added the line to free the long term buffers before
allocating a new one. This change inadvertently uncovered the problem
that the number of queues can change after a failover as well. To fix
this, we check whether or not the number of queues has changed in
do_reset and if they have, we do a full release and init of the queues.
-In patch 1/3, added variables to the adapter struct to track how
many rx/tx pools have actually been allocated and modify the release
pools routines to use these values rather than the possibly incorrect
req_rx/tx_queues values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen [Thu, 18 Jan 2018 22:27:58 +0000 (16:27 -0600)]
ibmvnic: Allocate and request vpd in init_resources
In reset events in which our memory allocations need to be reallocated,
VPD data is being freed, but never reallocated. This can cause issues if
we later attempt to access that memory or reset and attempt to free the
memory. This patch moves the allocation of the VPD data to init_resources
so that it will be symmetrically freed during release resources.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen [Thu, 18 Jan 2018 22:27:12 +0000 (16:27 -0600)]
ibmvnic: Revert to previous mtu when unsupported value requested
If we request an unsupported mtu value, the vnic server will suggest a
different value. Currently we take the suggested value without question
and login with that value. However, the behavior doesn't seem completely
sane as attempting to change the mtu to some specific value will change
the mtu to some completely different value most of the time. This patch
fixes the issue by logging in with the previously used mtu value and
printing an error message saying that the given mtu is unsupported.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen [Thu, 18 Jan 2018 22:26:31 +0000 (16:26 -0600)]
ibmvnic: Modify buffer size and number of queues on failover
Using newer backing devices can cause the required padding at the end of
buffer as well as the number of queues to change after a failover.
Since we currently assume that these values never change, after a
failover to a backing device with different capabilities, we can get
errors from the vnic server, attempt to free long term buffers that are
no longer there, or not free long term buffers that should be freed.
This patch resolves the issue by checking whether any of these values
change, and if so perform the necessary re-allocations.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Thu, 18 Jan 2018 21:11:07 +0000 (13:11 -0800)]
rds: tcp: compute m_ack_seq as offset from ->write_seq
rds-tcp uses m_ack_seq to track the tcp ack# that indicates
that the peer has received a rds_message. The m_ack_seq is
used in rds_tcp_is_acked() to figure out when it is safe to
drop the rds_message from the RDS retransmit queue.
The m_ack_seq must be calculated as an offset from the right
edge of the in-flight tcp buffer, i.e., it should be based on
the ->write_seq, not the ->snd_nxt.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Decotigny [Thu, 18 Jan 2018 17:59:13 +0000 (09:59 -0800)]
net: core: Expose number of link up/down transitions
Expose the number of times the link has been going UP or DOWN, and
update the "carrier_changes" counter to be the sum of these two events.
While at it, also update the sysfs-class-net documentation to cover:
carrier_changes (3.15), carrier_up_count (4.16) and carrier_down_count
(4.16)
Signed-off-by: David Decotigny <decot@googlers.com>
[Florian:
* rebase
* add documentation
* merge carrier_changes with up/down counters]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Thu, 18 Jan 2018 16:48:18 +0000 (17:48 +0100)]
macsec: restore uAPI after addition of GCM-AES-256
Commit
ccfdec908922 ("macsec: Add support for GCM-AES-256 cipher suite")
changed a few values in the uapi headers for MACsec.
Because of existing userspace implementations, we need to preserve the
value of MACSEC_DEFAULT_CIPHER_ID. Not doing that resulted in
wpa_supplicant segfaults when a secure channel was created using the
default cipher. Thus, swap MACSEC_DEFAULT_CIPHER_{ID,ALT} back to their
original values.
Changing the maximum length of the MACSEC_SA_ATTR_KEY attribute is
unnecessary, as the previous value (MACSEC_MAX_KEY_LEN, which was 128B)
is large enough to carry 32-bytes keys. This patch reverts
MACSEC_MAX_KEY_LEN to 128B and restores the old length check on
MACSEC_SA_ATTR_KEY.
Fixes:
ccfdec908922 ("macsec: Add support for GCM-AES-256 cipher suite")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 18 Jan 2018 02:37:34 +0000 (10:37 +0800)]
net: hns: Fix for variable may be used uninitialized warnings
When !CONFIG_REGMAP hns throws compiler warnings since
dsaf_read_syscon ignores the return result from regmap_read,
which allows val to be uninitialized.
Fixes:
86897c960b49 ("net: hns: add syscon operation for dsaf")
Reported-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Stach [Wed, 17 Jan 2018 18:30:55 +0000 (19:30 +0100)]
net: fec: add necessary defines to work on ARM64
The i.MX8 is a ARMv8 based SoC, that uses the same FEC IP as the
earlier, ARMv7 based, i.MX SoCs. Allow the driver to work on ARM64.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Wed, 17 Jan 2018 15:33:54 +0000 (16:33 +0100)]
usbnet: silence an unnecessary warning
That a kevent could not be scheduled is not an error.
Such handlers must be able to deal with multiple events anyway.
As the successful scheduling of a work is a debug event, make
the failure debug priority, too.
V2: coding style
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Cristian Caravena <caravena@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Jan 2018 20:26:57 +0000 (15:26 -0500)]
Merge branch 'cxgb4-tc-flower-offload-fixes'
Daniel Borkmann says:
====================
pull-request: bpf 2018-01-18
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a divide by zero due to wrong if (src_reg == 0) check in
64-bit mode. Properly handle this in interpreter and mask it
also generically in verifier to guard against similar checks
in JITs, from Eric and Alexei.
2) Fix a bug in arm64 JIT when tail calls are involved and progs
have different stack sizes, from Daniel.
3) Reject stores into BPF context that are not expected BPF_STX |
BPF_MEM variant, from Daniel.
4) Mark dst reg as unknown on {s,u}bounds adjustments when the
src reg has derived bounds from dead branches, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Wed, 17 Jan 2018 06:43:34 +0000 (12:13 +0530)]
cxgb4: fix endianness for vlan value in cxgb4_tc_flower
Don't change endianness when assigning vlan value in cxgb4_tc_flower
code when processing flow match parameters. The value gets converted
to network order as part of filtering code in set_filter_wr.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Wed, 17 Jan 2018 06:43:33 +0000 (12:13 +0530)]
cxgb4: set filter type to 1 for ETH_P_IPV6
For ethtype_key = ETH_P_IPV6, set filter type as 1 in cxgb4_tc_flower
code when processing flow match parameters.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toshiaki Makita [Wed, 17 Jan 2018 06:38:25 +0000 (15:38 +0900)]
virtio_net: Add ethtool stats
The main purpose of this patch is adding a way of checking per-queue stats.
It's useful to debug performance problems on multiqueue environment.
$ ethtool -S ens10
NIC statistics:
rx_queue_0_packets:
2090408
rx_queue_0_bytes:
3164825094
rx_queue_1_packets:
2082531
rx_queue_1_bytes:
3152932314
tx_queue_0_packets:
2770841
tx_queue_0_bytes:
4194955474
tx_queue_1_packets:
3084697
tx_queue_1_bytes:
4670196372
This change converts existing per-cpu stats structure into per-queue one.
This should not impact on performance since each queue counter is not
updated concurrently by multiple cpus.
Performance numbers:
- Guest has 2 vcpus and 2 queues
- Guest runs netserver
- Host runs 100-flow super_netperf
Before After Diff
UDP_STREAM 18byte 86.22 87.00 +0.90%
UDP_STREAM 1472byte 4055.27 4042.18 -0.32%
TCP_STREAM 16956.32 16890.63 -0.39%
UDP_RR 178667.11 185862.70 +4.03%
TCP_RR 128473.04 124985.81 -2.71%
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill A. Shutemov [Mon, 22 Jan 2018 09:22:30 +0000 (12:22 +0300)]
mm, page_vma_mapped: Introduce pfn_in_hpage()
The new helper would check if the pfn belongs to the page. For huge
pages it checks if the PFN is within range covered by the huge page.
The helper is used in check_pte(). The original code the helper replaces
had two call to page_to_pfn(). page_to_pfn() is relatively costly.
Although current GCC is able to optimize code to have one call, it's
better to do this explicitly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Mon, 22 Jan 2018 15:57:05 +0000 (10:57 -0500)]
Merge branch 'mvpp2-Armada-7k-8k-PP2-ACPI-support'
Marcin Wojtas says:
====================
Armada 7k/8k PP2 ACPI support
I quickly resend the series, thanks to Antoine Tenart's remark,
who spotted !CONFIG_ACPI compilation issue after introducing
the new fwnode_irq_get() routine. Please see the details in the changelog
below and the 3/7 commit log.
mvpp2 driver can work with the ACPI representation, as exposed
on a public branch:
https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/commits/marvell-armada-wip
It was compiled together with the most recent Tianocore EDK2 revision.
Please refer to the firmware build instruction on MacchiatoBin board:
http://wiki.macchiatobin.net/tiki-index.php?page=Build+from+source+-+UEFI+EDK+II
ACPI representation of PP2 controllers (withouth PHY support) can
be viewed in the github:
* MacchiatoBin:
https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/blob/
71ae395da1661374b0f07d1602afb1eee56e9794/Platforms/Marvell/Armada/AcpiTables/Armada80x0McBin/Dsdt.asl#L201
* Armada 7040 DB:
https://github.com/MarvellEmbeddedProcessors/edk2-open-platform/blob/
71ae395da1661374b0f07d1602afb1eee56e9794/Platforms/Marvell/Armada/AcpiTables/Armada70x0/Dsdt.asl#L131
I will appreciate any comments or remarks.
Best regards,
Marcin
Changelog:
v3 -> v4:
* 3/7
- add new macro (ACPI_HANDLE_FWNODE) and fix
compilation with !CONFIG_ACPI
- extend commit log and mention usability of fwnode_irq_get
for the child nodes as well
v2 -> v3:
* 1/7, 2/7
- Add Rafael's Acked-by's
* 3/7, 4/7
- New patches
* 6/7, 7/7
- Update driver with new helper routines usage
- Improve commit log.
v1 -> v2:
* Remove MDIO patches
* Use PP2 ports only with link interrupts
* Release second region resources in mvpp2 driver (code moved from
mvmdio), as explained in details in 5/5 commit message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 18 Jan 2018 12:31:44 +0000 (13:31 +0100)]
net: mvpp2: enable ACPI support in the driver
This patch introduces an alternative way of obtaining resources - via
ACPI tables provided by firmware. Enabling coexistence with the DT
support, in addition to the OF_*->device_*/fwnode_* API replacement,
required following steps to be taken:
* Add mvpp2_acpi_match table
* Omit clock configuration and obtain tclk from the property - in ACPI
world, the firmware is responsible for clock maintenance.
* Disable comphy and syscon handling as they are not available for ACPI.
* Modify way of obtaining interrupts - use newly introduced
fwnode_irq_get() routine
* Until proper MDIO bus and PHY handling with ACPI is established in the
kernel, use only link interrupts feature in the driver. For the RGMII
port it results in depending on GMAC settings done during firmware
stage.
* When booting with ACPI MVPP2_QDIST_MULTI_MODE is picked by
default, as there is no need to keep any kind of the backward
compatibility.
Moreover, a memory region used by mvmdio driver is usually placed in
the middle of the address space of the PP2 network controller.
The MDIO base address is obtained without requesting memory region
(by devm_ioremap() call) in mvmdio.c, later overlapping resources are
requested by the network driver, which is responsible for avoiding
a concurrent access.
In case the MDIO memory region is declared in the ACPI, it can
already appear as 'in-use' in the OS. Because it is overlapped by second
region of the network controller, make sure it is released, before
requesting it again. The care is taken by mvpp2 driver to avoid
concurrent access to this memory region.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 18 Jan 2018 12:31:43 +0000 (13:31 +0100)]
net: mvpp2: use device_*/fwnode_* APIs instead of of_*
OF functions can be used only for the driver using DT.
As a preparation for introducing ACPI support in mvpp2
driver, use struct fwnode_handle in order to obtain
properties from the hardware description.
This patch replaces of_* function with device_*/fwnode_*
where possible in the mvpp2.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 18 Jan 2018 12:31:42 +0000 (13:31 +0100)]
net: mvpp2: simplify maintaining enabled ports' list
'port_count' field of the mvpp2 structure holds an overall amount
of available ports, based on DT nodes status. In order to be prepared
to support other HW description, obtain the value by incrementing it
upon each successful port initialization. This allowed for simplifying
port indexing in the controller's private array, whose size is now not
dynamically allocated, but fixed to MVPP2_MAX_PORTS.
This patch simplifies creating and filling list of enabled ports and
is a part of the preparation for adding ACPI support in the mvpp2 driver.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 18 Jan 2018 12:31:41 +0000 (13:31 +0100)]
device property: Allow iterating over available child fwnodes
Implement a new helper function fwnode_get_next_available_child_node(),
which enables obtaining next enabled child fwnode, which
works on a similar basis to OF's of_get_next_available_child().
This commit also introduces a macro, thanks to which it is
possible to iterate over the available fwnodes, using the
new function described above.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 18 Jan 2018 12:31:40 +0000 (13:31 +0100)]
device property: Introduce fwnode_irq_get()
Until now there were two very similar functions allowing
to get Linux IRQ number from ACPI handle (acpi_irq_get())
and OF node (of_irq_get()). The first one appeared to be used
only as a subroutine of platform_irq_get(), which (in the generic
code) limited IRQ obtaining from _CRS method only to nodes
associated to kernel's struct platform_device.
This patch introduces a new helper routine - fwnode_irq_get(),
which allows to get the IRQ number directly from the fwnode
to be used as common for OF/ACPI worlds. It is usable not
only for the parents fwnodes, but also for the child nodes
comprising their own _CRS methods with interrupts description.
In order to be able o satisfy compilation with !CONFIG_ACPI
and also simplify the new code, introduce a helper macro
(ACPI_HANDLE_FWNODE), with which it is possible to reach
an ACPI handle directly from its fwnode.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 18 Jan 2018 12:31:39 +0000 (13:31 +0100)]
device property: Introduce fwnode_get_phy_mode()
Until now there were two almost identical functions for
obtaining network PHY mode - of_get_phy_mode() and,
more generic, device_get_phy_mode(). However it is not uncommon,
that the network interface is represented as a child
of the actual controller, hence it is not associated
directly to any struct device, required by the latter
routine.
This commit allows for getting the PHY mode for
children nodes in the ACPI world by introducing a new function -
fwnode_get_phy_mode(). This commit also changes
device_get_phy_mode() routine to be its wrapper, in order
to prevent unnecessary duplication.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Thu, 18 Jan 2018 12:31:38 +0000 (13:31 +0100)]
device property: Introduce fwnode_get_mac_address()
Until now there were two almost identical functions for
obtaining MAC address - of_get_mac_address() and, more generic,
device_get_mac_address(). However it is not uncommon,
that the network interface is represented as a child
of the actual controller, hence it is not associated
directly to any struct device, required by the latter
routine.
This commit allows for getting the MAC address for
children nodes in the ACPI world by introducing a new function -
fwnode_get_mac_address(). This commit also changes
device_get_mac_address() routine to be its wrapper, in order
to prevent unnecessary duplication.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 22 Jan 2018 15:25:43 +0000 (15:25 +0000)]
net: caif: remove redundant re-assignment of pointer pfrm
The pointer pfrm is initialized and then later re-assigned the same
value and hence the second assignment is redundant and can be removed.
Cleans up clang warning:
drivers/net/caif/caif_hsi.c:222:6: warning: Value stored to 'pfrm'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Mon, 22 Jan 2018 13:18:26 +0000 (18:48 +0530)]
cxgb4: add geneve offload support for T6
Add geneve segmentation offload support of T6 cards.
Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Jan 2018 14:36:37 +0000 (09:36 -0500)]
Merge tag 'mac80211-next-for-davem-2018-01-22' of git://git./linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Less than a handful of changes:
* possible memory leak fix in hwsim
* speed up hwsim
* add hwsim userspace rate control API
* code cleanups
====================
A conflict was resolved in mac80211_hwsim.c, mostly of
the simple overlapping changes category. One adding
a rhashtable and another adding a workqueue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 22 Jan 2018 10:31:19 +0000 (10:31 +0000)]
devlink: fix memory leak on 'resource'
Currently, if the call to devlink_resource_find returns null then
the error exit path does not free the devlink_resource 'resource'
and a memory leak occurs. Fix this by kfree'ing resource on the
error exit path.
Detected by CoverityScan, CID#
1464184 ("Resource leak")
Fixes:
d9f9b9a4d05f ("devlink: Add support for resource abstraction")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Jan 2018 14:22:11 +0000 (09:22 -0500)]
Merge branch 'mlxsw-spectrum_router-Optimize-LPM-trees'
Jiri Pirko says:
====================
mlxsw: spectrum_router: Optimize LPM trees
Ido says:
This set tries to optimize the structure of the LPM trees used for route
lookup by avoiding lookups that are guaranteed not to return a result.
This is done by making sure only used prefix lengths are present in the
tree.
First two patches are small preparatory steps towards the actual change
in the last patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Jan 2018 08:17:42 +0000 (09:17 +0100)]
mlxsw: spectrum_router: Remove unnecessary prefix lengths from LPM tree
In commit
fc922bb0dd94 ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I tried to make sure only used prefix lengths are
present in the LPM tree shared between all virtual routers.
However, this optimization had to be removed in commit
a69518cf0b4c
("mlxsw: spectrum_router: Avoid expensive lookup during route removal"),
since determining the used prefix lengths required us to traverse all
the active virtual routers, which could result in a hung task depending
on the number of VRFs and whether routes were removed due to abort or
not.
Re-introduce the optimization by moving the prefix usage accounting from
the virtual routers to the LPM tree, as this accounting is only used in
order to determine the tree's structure.
To make the sharing of the trees more explicit, the two trees (for IPv4
and IPv6) are stored in the shared router struct and upon the creation
of a virtual router it is immediately bound to both.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Jan 2018 08:17:41 +0000 (09:17 +0100)]
mlxsw: spectrum_router: Pass FIB node to LPM tree unlink function
Next patch will try to optimize the LPM tree and make sure only used
prefix lengths are present, to avoid unnecessary look-ups.
Pass the currently removed FIB node to the unlinking function as its
associated prefix length is a potential candidate for removal from the
tree.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 22 Jan 2018 08:17:40 +0000 (09:17 +0100)]
mlxsw: spectrum_router: Use the nodes list as indication for empty FIB
Currently, each FIB (IPv4 / IPv6) in a virtual router holds a prefix
usage that is used to choose a matching LPM tree, but also to check if
the FIB is empty, so that the LPM tree could be unbound.
Next patches will remove the reliance on the per-FIB prefix usage for
LPM tree matching. Keeping it only to check if the FIB is empty is a
waste, since we can use the nodes ({Prefix, Length}) list instead.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Mon, 22 Jan 2018 02:55:38 +0000 (10:55 +0800)]
tun: add missing rcu annotation
This patch fixes the following sparse warnings:
drivers/net/tun.c:2241:15: error: incompatible types in comparison expression (different address spaces)
Fixes:
cd5681d7d890 ("tuntap: rename struct tun_steering_prog to struct tun_prog")
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
weiyongjun (A) [Thu, 18 Jan 2018 02:23:34 +0000 (02:23 +0000)]
mac80211_hwsim: fix possible memory leak in hwsim_new_radio_nl()
'hwname' is malloced in hwsim_new_radio_nl() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes:
ff4dd73dd2b4 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Christopher Díaz Riveros [Wed, 17 Jan 2018 21:03:00 +0000 (16:03 -0500)]
debugfs_sta: Remove unneeded semicolons
Trivial fix removes unneeded semicolons after switch blocks.
Signed-off-by: Christopher Díaz Riveros <chrisadr@gentoo.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kirill A. Shutemov [Fri, 19 Jan 2018 12:49:24 +0000 (15:49 +0300)]
mm, page_vma_mapped: Drop faulty pointer arithmetics in check_pte()
Tetsuo reported random crashes under memory pressure on 32-bit x86
system and tracked down to change that introduced
page_vma_mapped_walk().
The root cause of the issue is the faulty pointer math in check_pte().
As ->pte may point to an arbitrary page we have to check that they are
belong to the section before doing math. Otherwise it may lead to weird
results.
It wasn't noticed until now as mem_map[] is virtually contiguous on
flatmem or vmemmap sparsemem. Pointer arithmetic just works against all
'struct page' pointers. But with classic sparsemem, it doesn't because
each section memap is allocated separately and so consecutive pfns
crossing two sections might have struct pages at completely unrelated
addresses.
Let's restructure code a bit and replace pointer arithmetic with
operations on pfns.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-and-tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Fixes:
ace71a19cec5 ("mm: introduce page_vma_mapped_walk()")
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Sun, 21 Jan 2018 23:21:31 +0000 (18:21 -0500)]
Merge branch 'mlxsw-Add-support-for-mirror-action-with-flower'
Jiri Pirko says:
====================
mlxsw: Add support for mirror action with flower
Arkadi says:
Add support for mirror action with flower classifier. The first 3 patches
introduce a generic per-block resource infra. The last 4 patches add
support for flow based span.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Fri, 19 Jan 2018 08:24:52 +0000 (09:24 +0100)]
mlxsw: spectrum_acl: Add support for mirror action
Add support for mirror action. Only one mirror action can be set per rule.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Fri, 19 Jan 2018 08:24:51 +0000 (09:24 +0100)]
mlxsw: spectrum: Extend mlxsw_afa_ops for counter index and implement for Spectrum
Introduce extension of mlxsw_afa_ops in order to add/del mirroring and
implement the ops for Spectrum.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Fri, 19 Jan 2018 08:24:50 +0000 (09:24 +0100)]
mlxsw: spectrum: Extend and export SPAN API
Extend SPAN API for ACL case. In case of ACL triggering the MPAR register
shouldn't be configured. This patch also export those helpers for
ACL usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Fri, 19 Jan 2018 08:24:49 +0000 (09:24 +0100)]
mlxsw: spectrum_acl: Add support for mirroring action
The patch extends the trap action for mirroring.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 19 Jan 2018 08:24:48 +0000 (09:24 +0100)]
mlxsw: core: Make counter index allocated inside the action append
So far, the caller of mlxsw_afa_block_append_counter needed to allocate
counter index by hand. Benefit from the previously introduced resource
infra and counter_index_get/put callbacks, and allocate the counter
index in place where it is needed, inside the action append function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 19 Jan 2018 08:24:47 +0000 (09:24 +0100)]
mlxsw: core: Convert fwd_entry_ref list to be generic per-block resource list
Since the resource list needs to be used also for other entries different
to fwd_entry_ref, make the list generic. For that purpose, introduce a
resource structure with couple of helpers that the code which need to
store a per-block resource should use.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 19 Jan 2018 08:24:46 +0000 (09:24 +0100)]
mlxsw: spectrum: Extend mlxsw_afa_ops for counter index and implement for Spectrum
Introduce extension of mlxsw_afa_ops in order to get/put counter indexes
and implement the ops for Spectrum.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 21 Jan 2018 23:19:04 +0000 (18:19 -0500)]
Merge branch 'Aquantia-atlantic-driver-new-devices-support'
Igor Russkikh says:
====================
Aquantia atlantic driver new devices support
This patchset introduces a support for new Aquantia hardware:
AQC11x family with updated hardware (B1) and firmware (2.x and 3.x branches).
For that, a number of improvements in overall driver model were done:
- Firmware specific ops tables. Firmware 2.x and 3.x series support
functions are now in separate fw2x module.
- PCI module cleanup and simplification done.
- Verified and tested hardware reset process.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:28 +0000 (17:03 +0300)]
net: aquantia: bump driver version to match aquantia internal numbering
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:27 +0000 (17:03 +0300)]
net: aquantia: Report correct mediatype via ethtool
For devices with known capabilities of Fibre media type we now report that
to ethtool.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:26 +0000 (17:03 +0300)]
net: aquantia: Introduce global AQC hardware reset sequence
The detailed reset sequence ensures all HW components are in aligned
state before NIC startup. It also supports cards with signed firmware (RBL)
and checks if their FW is valid.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:25 +0000 (17:03 +0300)]
net: aquantia: Introduce support for new firmware on AQC cards
This defines fw2x operations table and corresponding methods.
Some of the functions are being shared with 1.x firmware
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:24 +0000 (17:03 +0300)]
net: aquantia: Introduce firmware ops callbacks
New AQC cards will have an updated firmware with new binary interface.
This patch extracts firmware specific operations into a separate table
and prepares for the introduction of new fw 2.x and 3.x
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:23 +0000 (17:03 +0300)]
net: aquantia: Change confusing no_ff_addr to more meaningful name
The address to check if HW is not dead/hang could be stored in
capabilities, since it is a constant. Change its name to better reflect
the idea.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:22 +0000 (17:03 +0300)]
net: aquantia: Remove create/destroy from hw ops
These ops are not related to HW and are now implemented in pci module.
Thus, remove these ops pointers and implementation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:21 +0000 (17:03 +0300)]
net: aquantia: Cleanup pci functions module
Driver contained a dead code of maintaining multiple pci port instances.
That will never be used since for each pci function a separate NIC
instance is created.
Simplify this, making pci module only responsible for pci resource
management.
NIC initialization is also simplified accordingly.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:20 +0000 (17:03 +0300)]
net: aquantia: Convert hw and caps structures to const static pointers
This removes unnecessary structure copying, and prepares the driver for
separate firmware ops table introduction.
We also remove extra copy of capabilities structure (which is const actually)
and also replace it with a const pointer in aq_nic_cfg.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:19 +0000 (17:03 +0300)]
net: aquantia: Introduce new AQC devices and capabilities
A number of new AQC devices is going to be released. To support more
flexible capabilities management a number of static caps instances is now
declared. Devices now are mainly differs by supported speeds, but in future
more parameters will be customized. A set of AQC100 devices have
fibre media, not twisted pair - this is also reflected in
new capabilities definitions.
HW level also now directly exports hw_ops for each of A0/B0 hardware.
PCI configuration now uses a device configuration table where each
device ID is explicitly mapped with hardware OPs and capabilities
structures.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 19 Jan 2018 14:03:18 +0000 (17:03 +0300)]
net: aquantia: Introduce new device ids and constants
New set of aquantia devices has an upgraded hardware (B1).
The hardware interface is identical to B0. The difference will
be in firmware which is incompatible with old one.
Reorganized and removed duplicate speed and devid definitions
Introduced explicit flow control configuration defines
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 21 Jan 2018 23:13:23 +0000 (18:13 -0500)]
Merge tag 'mlx5-updates-2018-01-19' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-01-19
From: Or Gerlitz <ogerlitz@mellanox.com>
=======
First six patches of this series further enhances the mlx5 hairpin support.
The first two patches deal with using different hairpin instances
for flows whose packets have different priorities to align with the port
TX QoS model. The next four patches allow us to do HW spreading
of flows over a set of hairpin pairs using RSS. The last two patches
change the driver to also set the size of the HW hairpin queues.
========
Next four patches from Eran Ben Elisha <eranbe@mellanox.com>:
Add more debug data for TX timeout handling, and further enhance and optimize
TX timeout handling upon lost interrupts, which adds a mechanism for explicitly
polling EQ in case of a TX timeout in order to recover from a lost interrupt.
If this is not the case (no pending EQEs), perform a channels full recovery as
usual.
From Kamal Heib <kamalh@mellanox.com>, Two patches to extend the stats group API
to have an update_stats() callback which will be used to fetch the hardware or
software counters data, this will improve the current API and reduce code
duplication.
From Gal Pressman <galp@mellanox.com>, Last patch, Add likely to the common RX checksum
flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pieter Jansen van Vuuren [Sat, 20 Jan 2018 01:54:08 +0000 (17:54 -0800)]
nfp: flower: prioritize stats updates
Previously it was possible to interrupt processing stats updates because
they were handled in a work queue. Interrupting the stats updates could
lead to a situation where we backup the control message queue. This patch
moves the stats update processing out of the work queue to be processed as
soon as hardware sends a request.
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Talat Batheesh [Sun, 21 Jan 2018 03:30:42 +0000 (05:30 +0200)]
net/mlx5e: Fix fixpoint divide exception in mlx5e_am_stats_compare
Helmut reported a bug about division by zero while
running traffic and doing physical cable pull test.
When the cable unplugged the ppms become zero, so when
dividing the current ppms by the previous ppms in the
next dim iteration there is division by zero.
This patch prevent this division for both ppms and epms.
Fixes:
c3164d2fc48f ("net/mlx5e: Added BW check for DIM decision mechanism")
Reported-by: Helmut Grauer <helmut.grauer@de.ibm.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>