OSDN Git Service
Tariq Toukan [Wed, 21 Nov 2018 12:08:06 +0000 (14:08 +0200)]
net/mlx5e: XDP, Support Enhanced Multi-Packet TX WQE
Add support for the HW feature of multi-packet WQE in XDP
xmit flow.
The conventional TX descriptor (WQE, Work Queue Element) serves
a single packet. Our HW has support for multi-packet WQE (MPWQE)
in which a single descriptor serves multiple TX packets.
This reduces both the PCI overhead and the CPU cycles wasted on
writing them.
In this patch we add support for the HW feature, which is supported
starting from ConnectX-5.
Performance:
Tested packet rate for UDP 64Byte multi-stream over ConnectX-5 NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
XDP_TX:
We see a huge gain on single port ConnectX-5, and reach the 100 Mpps
milestone.
* Single-port HCA:
Before: 70 Mpps
After: 100 Mpps (+42.8%)
* Dual-port HCA:
Before: 51.7 Mpps
After: 57.3 Mpps (+10.8%)
* In both cases we tested traffic on one port and for now On Dual-port HCAs
we see only small gain, we are working to overcome this bottleneck, but
for the moment only with experimental firmware on dual port HCAs we can
reach the wanted numbers as seen on Single-port HCAs.
XDP_REDIRECT:
Redirect from (A) ConnectX-5 to (B) ConnectX-5.
Due to a setup limitation, (A) and (B) are on different NUMA nodes,
so absolute performance numbers are not optimal.
Note:
Below is the transmit rate of (B), not the redirect rate of (A)
which is in some cases higher.
* (B) is single-port:
Before: 77 Mpps
After: 90 Mpps (+16.8%)
* (B) is dual-port:
Before: 61 Mpps
After: 72 Mpps (+18%)
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Sun, 14 Oct 2018 11:46:57 +0000 (14:46 +0300)]
net/mlx5e: XDP, Add array for WQE info descriptors
Each xdp_wqe_info instance describes the number of data-segments
and WQEBBs of the WQE.
This is useful for a downstream patch that adds support for
Multi-Packet TX WQE feature.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Sun, 14 Oct 2018 11:37:48 +0000 (14:37 +0300)]
net/mlx5e: XDP, Maintain a FIFO structure for xdp_info instances
This provides infrastructure to have multiple xdp_info instances
for the same consumer index.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Wed, 21 Nov 2018 12:06:02 +0000 (14:06 +0200)]
net/mlx5e: XDP, Replace boolean doorbell indication with segment pointer
Instead of calculating the control segment to be used upon an
XDP xmit doorbell, save it in SQ structure.
Nullify when no pending doorbell.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Thu, 15 Nov 2018 09:48:41 +0000 (11:48 +0200)]
net/mlx5e: XDP, Warn upon polling an error CQE
Do not ignore the CQE opcode.
This helps expose issues and debug them.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Wed, 21 Nov 2018 12:04:45 +0000 (14:04 +0200)]
net/mlx5e: XDP, Change the XDP SQ redirect indication
Do not maintain an SQ state bit to indicate whether an
XDP SQ serves redirect operations.
Instead, rely on the fact that such an XDP SQ doesn't reside
in an RQ instance, while the others do.
This info is not known to the XDP SQ functions themselves,
and they rely on their callers to distinguish between the cases.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Wed, 21 Nov 2018 11:56:17 +0000 (13:56 +0200)]
net/mlx5e: XDP, Precede XDP-related operations in RQ poll by a loaded program check
At the end of the RQ polling loop, some XDP-related operations
might be required. Before checking them one by one, check if
an XDP program is even loaded.
Combine all the checks and operations in a single function in xdp files.
This saves unnecessary checks for non-XDP flows.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Thu, 15 Nov 2018 09:48:41 +0000 (11:48 +0200)]
net/mlx5e: TX, Print opcode in error CQE warning
The opcode indicates about the error reason.
Printing it helps in debug.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Willem de Bruijn [Thu, 20 Dec 2018 22:14:54 +0000 (17:14 -0500)]
virtio-net: ethtool configurable LRO
Virtio-net devices negotiate LRO support with the host.
Display the initially negotiated state with ethtool -k.
Also allow configuring it with ethtool -K, reusing the existing
virtnet_set_guest_offloads helper that configures LRO for XDP.
This is conditional on VIRTIO_NET_F_CTRL_GUEST_OFFLOADS.
Virtio-net negotiates TSO4 and TSO6 separately, but ethtool does not
distinguish between the two. Display LRO as on only if any offload
is active.
RTNL is held while calling virtnet_set_features, same as on the path
from virtnet_xdp_set.
Changes v1 -> v2
- allow ethtool config (-K) only if VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
- show LRO as enabled if any LRO variant is enabled
- do not allow configuration while XDP is active
- differentiate current features from the capable set, to restore
on XDP down only those features that were active on XDP up
- move test out of VIRTIO_NET_F_CSUM/TSO branch, which is tx only
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 21 Dec 2018 02:20:26 +0000 (18:20 -0800)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Support for destination MAC in ipset, from Stefano Brivio.
2) Disallow all-zeroes MAC address in ipset, also from Stefano.
3) Add IPSET_CMD_GET_BYNAME and IPSET_CMD_GET_BYINDEX commands,
introduce protocol version number 7, from Jozsef Kadlecsik.
A follow up patch to fix ip_set_byindex() is also included
in this batch.
4) Honor CTA_MARK_MASK from ctnetlink, from Andreas Jaggi.
5) Statify nf_flow_table_iterate(), from Taehee Yoo.
6) Use nf_flow_table_iterate() to simplify garbage collection in
nf_flow_table logic, also from Taehee Yoo.
7) Don't use _bh variants of call_rcu(), rcu_barrier() and
synchronize_rcu_bh() in Netfilter, from Paul E. McKenney.
8) Remove NFC_* cache definition from the old caching
infrastructure.
9) Remove layer 4 port rover in NAT helpers, use random port
instead, from Florian Westphal.
10) Use strscpy() in ipset, from Qian Cai.
11) Remove NF_NAT_RANGE_PROTO_RANDOM_FULLY branch now that
random port is allocated by default, from Xiaozhou Liu.
12) Ignore NF_NAT_RANGE_PROTO_RANDOM too, from Florian Westphal.
13) Limit port allocation selection routine in NAT to avoid
softlockup splats when most ports are in use, from Florian.
14) Remove unused parameters in nf_ct_l4proto_unregister_sysctl()
from Yafang Shao.
15) Direct call to nf_nat_l4proto_unique_tuple() instead of
indirection, from Florian Westphal.
16) Several patches to remove all layer 4 NAT indirections,
remove nf_nat_l4proto struct, from Florian Westphal.
17) Fix RTP/RTCP source port translation when SNAT is in place,
from Alin Nastac.
18) Selective rule dump per chain, from Phil Sutter.
19) Revisit CLUSTERIP target, this includes a deadlock fix from
netns path, sleep in atomic, remove bogus WARN_ON_ONCE()
and disallow mismatching IP address and MAC address.
Patchset from Taehee Yoo.
20) Update UDP timeout to stream after 2 seconds, from Florian.
21) Shrink UDP established timeout to 120 seconds like TCP timewait.
22) Sysctl knobs to set GRE timeouts, from Yafang Shao.
23) Move seq_print_acct() to conntrack core file, from Florian.
24) Add enum for conntrack sysctl knobs, also from Florian.
25) Place nf_conntrack_acct, nf_conntrack_helper, nf_conntrack_events
and nf_conntrack_timestamp knobs in the core, from Florian Westphal.
As a side effect, shrink netns_ct structure by removing obsolete
sysctl anchors, also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 21 Dec 2018 01:31:36 +0000 (17:31 -0800)]
Merge git://git./linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-21
The following pull-request contains BPF updates for your *net-next* tree.
There is a merge conflict in test_verifier.c. Result looks as follows:
[...]
},
{
"calls: cross frame pruning",
.insns = {
[...]
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "function calls to other bpf functions are allowed for root only",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
{
"jset: functional",
.insns = {
[...]
{
"jset: unknown const compare not taken",
.insns = {
BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0,
BPF_FUNC_get_prandom_u32),
BPF_JMP_IMM(BPF_JSET, BPF_REG_0, 1, 1),
BPF_LDX_MEM(BPF_B, BPF_REG_8, BPF_REG_9, 0),
BPF_EXIT_INSN(),
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "!read_ok",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
[...]
{
"jset: range",
.insns = {
[...]
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.result_unpriv = ACCEPT,
.result = ACCEPT,
},
The main changes are:
1) Various BTF related improvements in order to get line info
working. Meaning, verifier will now annotate the corresponding
BPF C code to the error log, from Martin and Yonghong.
2) Implement support for raw BPF tracepoints in modules, from Matt.
3) Add several improvements to verifier state logic, namely speeding
up stacksafe check, optimizations for stack state equivalence
test and safety checks for liveness analysis, from Alexei.
4) Teach verifier to make use of BPF_JSET instruction, add several
test cases to kselftests and remove nfp specific JSET optimization
now that verifier has awareness, from Jakub.
5) Improve BPF verifier's slot_type marking logic in order to
allow more stack slot sharing, from Jiong.
6) Add sk_msg->size member for context access and add set of fixes
and improvements to make sock_map with kTLS usable with openssl
based applications, from John.
7) Several cleanups and documentation updates in bpftool as well as
auto-mount of tracefs for "bpftool prog tracelog" command,
from Quentin.
8) Include sub-program tags from now on in bpf_prog_info in order to
have a reliable way for user space to get all tags of the program
e.g. needed for kallsyms correlation, from Song.
9) Add BTF annotations for cgroup_local_storage BPF maps and
implement bpf fs pretty print support, from Roman.
10) Fix bpftool in order to allow for cross-compilation, from Ivan.
11) Update of bpftool license to GPLv2-only + BSD-2-Clause in order
to be compatible with libbfd and allow for Debian packaging,
from Jakub.
12) Remove an obsolete prog->aux sanitation in dump and get rid of
version check for prog load, from Daniel.
13) Fix a memory leak in libbpf's line info handling, from Prashant.
14) Fix cpumap's frame alignment for build_skb() so that skb_shared_info
does not get unaligned, from Jesper.
15) Fix test_progs kselftest to work with older compilers which are less
smart in optimizing (and thus throwing build error), from Stanislav.
16) Cleanup and simplify AF_XDP socket teardown, from Björn.
17) Fix sk lookup in BPF kselftest's test_sock_addr with regards
to netns_id argument, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 21 Dec 2018 01:01:17 +0000 (17:01 -0800)]
Merge branch 'expand-txtimestamp-selftest'
Willem de Bruijn says:
====================
expand txtimestamp selftest
Convert the existing txtimestamp test to run as part of kselftest
and return a pass/fail.
Also expand the variations of timestamping tested, including packet
sockets, ipv6 raw and dgram and passing options using cmsg.
These are enough changes to split across a few patches, even if all
changes are only this one test.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Thu, 20 Dec 2018 21:22:54 +0000 (16:22 -0500)]
selftests: add txtimestamp kselftest
Run the transmit timestamp tests as part of kselftests.
Add a txtimestamp.sh test script that runs most variants:
ipv4/ipv6, tcp/udp/raw/raw_ipproto/pf_packet, data/nodata,
setsockopt/cmsg. The script runs tests with netem delays.
Refine txtimestamp.c to validate results. Take expected
netem delays as input and compare against real timestamps.
To run without dependencies, add a listener socket to be
able to connect in the case of TCP.
Add the timestamping directory to the kselftests Makefile.
Build all the binaries. Only run verified txtimestamp.sh.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Thu, 20 Dec 2018 21:22:53 +0000 (16:22 -0500)]
selftests: expand txtimestamp with ipv6 dgram + raw and pf_packet
Expand the transmit timestamp regression test with support for
missing protocols: ipv6 datagram and raw and pf_packet.
Also refine resolve_hostname to independently request AF_INET or
AF_INET6 addresses. Else, ipv4 addresses may be returned as AF_INET6.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Thu, 20 Dec 2018 21:22:52 +0000 (16:22 -0500)]
selftests: expand txtimestamp with cmsg support
Commit
3dd17e63f513 ("sock: accept SO_TIMESTAMPING flags in socket
cmsg") added support for passing tx timestamping options per-call
in sendmsg.
Expand the txtimestamp test with support for this feature.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Oskolkov [Thu, 20 Dec 2018 18:51:49 +0000 (10:51 -0800)]
net: seg6.h: remove an unused #include
A minor code cleanup.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sam Protsenko [Thu, 20 Dec 2018 18:29:20 +0000 (20:29 +0200)]
ppp: Move PFC decompression to PPP generic layer
Extract "Protocol" field decompression code from transport protocols to
PPP generic layer, where it actually belongs. As a consequence, this
patch fixes incorrect place of PFC decompression in L2TP driver (when
it's not PPPOX_BOUND) and also enables this decompression for other
protocols, like PPPoE.
Protocol field decompression also happens in PPP Multilink Protocol
code and in PPP compression protocols implementations (bsd, deflate,
mppe). It looks like there is no easy way to get rid of that, so it was
decided to leave it as is, but provide those cases with appropriate
comments instead.
Changes in v2:
- Fix the order of checking skb data room and proto decompression
- Remove "inline" keyword from ppp_decompress_proto()
- Don't split line before function name
- Prefix ppp_decompress_proto() function with "__"
- Add ppp_decompress_proto() function with skb data room checks
- Add description for introduced functions
- Fix comments (as per review on mailing list)
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 21 Dec 2018 00:47:10 +0000 (16:47 -0800)]
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Thu, 20 Dec 2018 17:52:28 +0000 (09:52 -0800)]
linux/netlink.h: drop unnecessary extern prefix
Don't need extern prefix before function prototypes.
Checkpatch has complained about this for a couple of years.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 21 Dec 2018 00:42:39 +0000 (16:42 -0800)]
Merge branch 'ipv4-Prevent-user-triggerable-warning'
Ido Schimmel says:
====================
net: ipv4: Prevent user triggerable warning
Patch #1 prevents a user triaggerable warning in the flow dissector by
setting 'skb->dev' in skbs used for IPv4 output route get requests.
Patch #2 adds a test case that triggers the warning without the first
patch.
I have audited all the RTM_GETROUTE handlers and could not find any
other callpath where an skb is passed to the flow dissector with both
'skb->dev' and 'skb->sk' cleared.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 17:03:29 +0000 (17:03 +0000)]
selftests: rtnetlink: Add a test case for multipath route get
Without previous patch a warning would be generated upon multipath route
get when FIB multipath hash policy is to use a 5-tuple for multipath
hash calculation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 17:03:27 +0000 (17:03 +0000)]
net: ipv4: Set skb->dev for output route resolution
When user requests to resolve an output route, the kernel synthesizes
an skb where the relevant parameters (e.g., source address) are set. The
skb is then passed to ip_route_output_key_hash_rcu() which might call
into the flow dissector in case a multipath route was hit and a nexthop
needs to be selected based on the multipath hash.
Since both 'skb->dev' and 'skb->sk' are not set, a warning is triggered
in the flow dissector [1]. The warning is there to prevent codepaths
from silently falling back to the standard flow dissector instead of the
BPF one.
Therefore, instead of removing the warning, set 'skb->dev' to the
loopback device, as its not used for anything but resolving the correct
namespace.
[1]
WARNING: CPU: 1 PID: 24819 at net/core/flow_dissector.c:764 __skb_flow_dissect+0x314/0x16b0
...
RSP: 0018:
ffffa0df41fdf650 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
ffff8bcded232000 RCX:
0000000000000000
RDX:
ffffa0df41fdf7e0 RSI:
ffffffff98e415a0 RDI:
ffff8bcded232000
RBP:
ffffa0df41fdf760 R08:
0000000000000000 R09:
0000000000000000
R10:
ffffa0df41fdf7e8 R11:
ffff8bcdf27a3000 R12:
ffffffff98e415a0
R13:
ffffa0df41fdf7e0 R14:
ffffffff98dd2980 R15:
ffffa0df41fdf7e0
FS:
00007f46f6897680(0000) GS:
ffff8bcdf7a80000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
000055933e95f9a0 CR3:
000000021e636000 CR4:
00000000001006e0
Call Trace:
fib_multipath_hash+0x28c/0x2d0
? fib_multipath_hash+0x28c/0x2d0
fib_select_path+0x241/0x32f
? __fib_lookup+0x6a/0xb0
ip_route_output_key_hash_rcu+0x650/0xa30
? __alloc_skb+0x9b/0x1d0
inet_rtm_getroute+0x3f7/0xb80
? __alloc_pages_nodemask+0x11c/0x2c0
rtnetlink_rcv_msg+0x1d9/0x2f0
? rtnl_calcit.isra.24+0x120/0x120
netlink_rcv_skb+0x54/0x130
rtnetlink_rcv+0x15/0x20
netlink_unicast+0x20a/0x2c0
netlink_sendmsg+0x2d1/0x3d0
sock_sendmsg+0x39/0x50
___sys_sendmsg+0x2a0/0x2f0
? filemap_map_pages+0x16b/0x360
? __handle_mm_fault+0x108e/0x13d0
__sys_sendmsg+0x63/0xa0
? __sys_sendmsg+0x63/0xa0
__x64_sys_sendmsg+0x1f/0x30
do_syscall_64+0x5a/0x120
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
d0e13a1488ad ("flow_dissector: lookup netns by skb->sk if skb->dev is NULL")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steen Hegelund [Thu, 20 Dec 2018 13:16:31 +0000 (14:16 +0100)]
net: mscc: ocelot: Register poll timeout should be wall time not attempts
When doing indirect access in the Ocelot chip, a command is setup,
issued and then we need to poll until the result is ready. The polling
timeout is specified in milliseconds in the datasheet and not in
register access attempts.
It is not a bug on the currently supported platform, but we observed
that the code does not work properly on other platforms that we want to
support as the timing requirements there are different.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 20 Dec 2018 16:50:50 +0000 (16:50 +0000)]
neighbour: remove stray semicolon
Currently the stray semicolon means that the final term in the addition
is being missed. Fix this by removing it. Cleans up clang warning:
net/core/neighbour.c:2821:9: warning: expression result unused [-Wunused-value]
Fixes:
82cbb5c631a0 ("neighbour: register rtnl doit handler")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tristram Ha [Thu, 20 Dec 2018 02:59:31 +0000 (18:59 -0800)]
net: dsa: microchip: fix unicast frame leak
Port partitioning is done by enabling UNICAST_VLAN_BOUNDARY and changing
the default port membership of 0x7f to other values such that there is
no communication between ports. In KSZ9477 the member for port 1 is
0x41; port 2, 0x42; port 3, 0x44; port 4, 0x48; port 5, 0x50; and port 7,
0x60. Port 6 is the host port.
Setting a zero value can be used to stop port from receiving.
However, when UNICAST_VLAN_BOUNDARY is disabled and the unicast addresses
are already learned in the dynamic MAC table, setting zero still allows
devices connected to those ports to communicate. This does not apply to
multicast and broadcast addresses though. To prevent these leaks and
make the function of port membership consistent UNICAST_VLAN_BOUNDARY
should never be disabled.
Note that UNICAST_VLAN_BOUNDARY is enabled by default in KSZ9477.
Fixes:
b987e98e50ab90e5 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 21 Dec 2018 00:14:22 +0000 (16:14 -0800)]
vxlan: Correct merge error.
When resolving the conflict wrt. the vxlan_fdb_update call
in vxlan_changelink() I made the last argument false instead
of true.
Fix this.
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Tue, 18 Dec 2018 22:04:50 +0000 (23:04 +0100)]
netfilter: netns: shrink netns_ct struct
remove the obsolete sysctl anchors and move auto_assign_helper_warned
to avoid/cover a hole. Reduces size by 40 bytes on 64 bit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Thu, 20 Dec 2018 23:51:55 +0000 (15:51 -0800)]
Merge tag 'mlx5-updates-2018-12-19' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-12-19
This series adds some misc updates and the support for tunnels over VLAN
tc offloads.
From Miroslav Lichvar, patches #1,2
1) Update timecounter at least twice per counter overflow
2) Extend PTP gettime function to read system clock
From Gavi Teitz, patch #3
3) Increase VF representors' SQ size to 128
From Eli Britstein and Or Gerlitz, patches #4-10
4) Adds the capability to support tunnels over VLAN device.
Patch 4 avoids crash for TC flow with egress upper devices
Patch 5 refactors tunnel routing devs into a helper function
Patch 6 avoids crash for TC encap flows with vlan on underlay
Patches 7-8 refactor encap tunnel header preparing code.
Patch 9 adds support for building VLAN tagged ETH header.
Patch 10 adds support for tunnel routing to VLAN device.
From Aviv, patches 11,12 to fix earlier VF lag series
5) Fix query_nic_sys_image_guid() error during init
6) Fix LAG requirement when CONFIG_MLX5_ESWITCH is off
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Tue, 18 Dec 2018 22:04:49 +0000 (23:04 +0100)]
netfilter: conntrack: remove empty pernet fini stubs
after moving sysctl handling into single place, the init functions
can't fail anymore and some of the fini functions are empty.
Remove them and change return type to void.
This also simplifies error unwinding in conntrack module init path.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Tue, 18 Dec 2018 22:04:48 +0000 (23:04 +0100)]
netfilter: conntrack: merge ecache and timestamp sysctl tables with main one
Similar to previous change, this time for eache and timestamp.
Unlike helper and acct, these can be disabled at build time, so they
need ifdef guards.
Next patch will remove a few (now obsolete) functions.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Tue, 18 Dec 2018 22:04:47 +0000 (23:04 +0100)]
netfilter: conntrack: merge acct and helper sysctl table with main one
Needless copy&paste, just handle all in one. Next patch will handle
acct and timestamp, which have similar functions.
Intentionally leaves cruft behind, will be cleaned up in a followup
patch.
The obsolete sysctl pointers in netns_ct struct are left in place and
removed in a single change, as changes to netns trigger rebuild of
almost all files.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Tue, 18 Dec 2018 22:04:46 +0000 (23:04 +0100)]
netfilter: conntrack: add mnemonics for sysctl table
Its a bit hard to see what table[3] really lines up with, so add
human-readable mnemonics and use them for initialisation.
This makes it easier to see e.g. which sysctls are not exported to
unprivileged userns.
objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Tue, 18 Dec 2018 22:04:45 +0000 (23:04 +0100)]
netfilter: conntrack: un-export seq_print_acct
Only one caller, just place it where its needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Yafang Shao [Tue, 18 Dec 2018 13:14:07 +0000 (21:14 +0800)]
netfilter: conntrack: register sysctl table for gre
This patch adds two sysctl knobs for GRE:
net.netfilter.nf_conntrack_gre_timeout = 30
net.netfilter.nf_conntrack_gre_timeout_stream = 180
Update the Documentation as well.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Thu, 20 Dec 2018 23:48:55 +0000 (15:48 -0800)]
Merge branch 'mlxsw-Two-usability-improvements'
Ido Schimmel says:
====================
mlxsw: Two usability improvements
This patchset contains two small improvements in the mlxsw driver. The
first one, in patches #1-#2, relieves the user from the need to
configure a VLAN interface and only later the corresponding VXLAN
tunnel. The issue is explained in detail in the first patch.
The second improvement is described below and allows the user to make
use of VID 1 by having the driver use the reserved 4095 VID for untagged
traffic.
VLAN entries on a given port can be associated with either a bridge or a
router. For example, if swp1.10 is assigned an IP address and swp1.20 is
enslaved to a VLAN-unaware bridge, then both {Port 1, VID 10} and {Port
1, VID 20} would be associated with a filtering identifier (FID) of the
correct type.
In case swp1 itself is assigned an IP address or enslaved to a
VLAN-unaware bridge, then a FID would be associated with {Port 1, VID
1}. Using VID 1 for this purpose means that VLAN devices with VID 1
cannot be created over mlxsw ports, as this VID is (ab)used as the
default VLAN.
Instead of using VID 1 for this purpose, we can use VID 4095 which is
reserved for internal use and cannot be configured by either the 8021q
or the bridge driver.
Patches #3-#7 perform small and non-functional changes that finally
allow us to switch to VID 4095 as the default VID in patch #8.
Patch #9 removes the limitation about creation of VLAN devices with VID
1 over mlxsw ports.
Patches #10-#11 add test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:37 +0000 (19:42 +0000)]
selftests: forwarding: Add router test with VID 1
Previous patches made it possible to setup VLAN devices with VID 1 over
mlxsw ports. Verify this functionality actually works by conducting a
simple router test over VID 1.
Adding this test as a generic test since it can be run using veth pairs
and it can also be useful for other physical devices where VID 1 was
considered reserved (knowingly or not).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:35 +0000 (19:42 +0000)]
selftests: mlxsw: Adjust test regarding VID 1
Previous patches made it possible to create VLAN devices with VID 1 over
mlxsw ports. Adjust the test to verify such an operation succeeds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:34 +0000 (19:42 +0000)]
mlxsw: spectrum: Remove limitation regarding VID 1
VID 1 is not reserved anymore, so remove the check that prevented the
creation of VLAN devices with this VID over mlxsw ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:33 +0000 (19:42 +0000)]
mlxsw: spectrum: Switch to VID 4095 as default VID
There is no need to abuse VID 1 anymore and we can instead use VID 4095
as the default VLAN, which will be configured on the port throughout its
lifetime.
The OVS join / leave functions are changed to enable VIDs 1-4094
(inclusive) instead of 2-4095. This because VID 4095 is now the default
VLAN instead of 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:32 +0000 (19:42 +0000)]
mlxsw: spectrum: Add an helper function to cleanup VLAN entries
VLAN entries on a port can be associated with either a bridge VLAN or a
router port. Before the VLAN entry is destroyed these associations need
to be cleaned up.
Currently, this is always invoked from the function which destroys the
VLAN entry, but next patch is going to skip the destruction of the
default entry when a port in unlinked from a LAG.
The above does not mean that the associations should not be cleaned up,
so add a helper that will be invoked from both call sites.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:30 +0000 (19:42 +0000)]
mlxsw: spectrum: Store pointer to default port VLAN in port struct
Subsequent patches will need to access the default port VLAN. Since this
VLAN will exist throughout the lifetime of the port, simply store it in
the port's struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:29 +0000 (19:42 +0000)]
mlxsw: spectrum: Allow controlling destruction of default port VLAN
The function allows flushing all the existing VLAN entries on a port. It
is invoked when a port is destroyed and when it is unlinked from a LAG.
In the latter case, when moving to the new default VLAN, there will not
be a need to destroy the default VLAN entry.
Therefore, add an argument that allows to control whether the default
port VLAN should be destroyed or not. Currently it is always set to
'true'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:27 +0000 (19:42 +0000)]
mlxsw: spectrum: Set PVID during port initialization
Currently, the driver does not set the port's PVID when initializing a
new port. This is because the driver is using VID 1 as PVID which is the
firmware default.
Subsequent patches are going to change the PVID the driver is setting
when initializing a new port.
Prepare for that by explicitly setting the port's PVID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:26 +0000 (19:42 +0000)]
mlxsw: spectrum: Replace hard-coded default VID with a define
Subsequent patches are going to replace the current default VID (1) with
VLAN_N_VID - 1 (4095).
Prepare for this conversion by replacing the hard-coded '1' with a
define.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:25 +0000 (19:42 +0000)]
selftests: mlxsw: Add a test case for L3 VNI
Previous patch added the ability to offload a VXLAN tunnel used for L3
VNI when it is present in the VLAN-aware bridge before the corresponding
VLAN interface is configured. This patch adds a test case to verify
that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 20 Dec 2018 19:42:23 +0000 (19:42 +0000)]
mlxsw: spectrum_router: Do not force specific configuration order
In symmetric routing, the only two members in the VLAN corresponding to
the L3 VNI are the router port and the VXLAN tunnel.
In case the VXLAN device is already enslaved to the bridge and only
later the VLAN interface is configured, the tunnel will not be
offloaded.
The reason for this is that when the router interface (RIF)
corresponding to the VLAN interface is configured, it calls the core
fid_get() API which does not check if NVE should be enabled on the FID.
Instead, call into the bridge code which will check if NVE should be
enabled on the FID.
This effectively means that the same code path is used to retrieve a FID
when either a local port or a router port joins the FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 17 Dec 2018 23:05:29 +0000 (00:05 +0100)]
netfilter: conntrack: udp: set stream timeout to 2 minutes
We have no explicit signal when a UDP stream has terminated, peers just
stop sending.
For suspected stream connections a timeout of two minutes is sane to keep
NAT mapping alive a while longer.
It matches tcp conntracks 'timewait' default timeout value.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Thu, 6 Dec 2018 10:50:49 +0000 (11:50 +0100)]
netfilter: conntrack: udp: only extend timeout to stream mode after 2s
Currently DNS resolvers that send both A and AAAA queries from same source port
can trigger stream mode prematurely, which results in non-early-evictable conntrack entry
for three minutes, even though DNS requests are done in a few milliseconds.
Add a two second grace period where we continue to use the ordinary
30-second default timeout. Its enough for DNS request/response traffic,
even if two request/reply packets are involved.
ASSURED is still set, else conntrack (and thus a possible
NAT mapping ...) gets zapped too in case conntrack table runs full.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Thu, 20 Dec 2018 23:34:30 +0000 (15:34 -0800)]
Merge branch '1GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-12-20
This series contains updates to e100, igb, ixgbe, i40e and ice drivers.
I replaced spinlocks for mutex locks to reduce the latency on CPU0 for
igb when updating the statistics. This work was based off a patch
provided by Jan Jablonsky, which was against an older version of the igb
driver.
Jesus adjusts the receive packet buffer size from 32K to 30K when
running in QAV mode, to stay within 60K for total packet buffer size for
igb.
Vinicius adds igb kernel documentation regarding the CBS algorithm and
its implementation in the i210 family of NICs.
YueHaibing from Huawei fixed the e100 driver that was potentially
passing a NULL pointer, so use the kernel macro IS_ERR_OR_NULL()
instead.
Konstantin Khorenko fixes i40e where we were not setting up the
neigh_priv_len in our net_device, which caused the driver to read beyond
the neighbor entry allocated memory.
Miroslav Lichvar extends the PTP gettime() to read the system clock by
adding support for PTP_SYS_OFFSET_EXTENDED ioctl in i40e.
Young Xiao fixed the ice driver to only enable NAPI on q_vectors that
actually have transmit and receive rings.
Kai-Heng Feng fixes an igb issue that when placed in suspend mode, the
NIC does not wake up when a cable is plugged in. This was due to the
driver not setting PME during runtime suspend.
Stephen Douthit enables the ixgbe driver allow DSA devices to use the
MII interface to talk to switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 20 Dec 2018 22:47:10 +0000 (23:47 +0100)]
Merge branch 'bpf-sockmap-fixes-and-improvements'
John Fastabend says:
====================
Set of bpf fixes and improvements to make sockmap with kTLS usable
with "real" applications. This set came as the fallout of pulling
kTLS+sockmap into Cilium[1] and running in container environment.
Roughly broken into three parts,
Patches 1-3: resolve/improve handling of size field in sk_msg_md
Patch 4: it became difficult to use this in Cilium when the
SK_PASS verdict was not correctly handle. So handle
the case correctly.
Patch 5-8: Set of issues found while running OpenSSL TX kTLS
enabled applications. This resolves the most obvious
issues and gets applications using kTLS TX up and
running with sock{map|has}.
Other than the "sk_msg, zap ingress queue on psock down" (PATCH 6/8)
which can potentially cause a WARNING the issues fixed in this
series do not cause kernel side warnings, BUG, etc. but instead
cause stalls and other odd behavior in the user space applications
when using kTLS with BPF policies applied.
Primarily tested with 'curl' compiled with latest openssl and
also 'openssl s_client/s_server' containers using Cilium network
plugin with docker/k8s. Some basic testing with httpd was also
enabled. Cilium CI tests will be added shortly to cover these
cases as well. We also have 'wrk' and other test and benchmarking
tools we can run now.
We have two more sets of patches currently under testing that
will be sent shortly to address a few more issues. First the
OpenSSL RX kTLS side breaks when both sk_msg and sk_skb_verdict
programs are used with kTLS, the sk_skb_verdict programs are
not enforced. Second skmsg needs to call into tcp stack to
send to indicate consumed data.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Thu, 20 Dec 2018 19:35:36 +0000 (11:35 -0800)]
bpf: tls_sw, init TLS ULP removes BPF proto hooks
The existing code did not expect users would initialize the TLS ULP
without subsequently calling the TLS TX enabling socket option.
If the application tries to send data after the TLS ULP enable op
but before the TLS TX enable op the BPF sk_msg verdict program is
skipped. This patch resolves this by converting the ipv4 sock ops
to be calculated at init time the same way ipv6 ops are done. This
pulls in any changes to the sock ops structure that have been made
after the socket was created including the changes from adding the
socket to a sock{map|hash}.
This was discovered by running OpenSSL master branch which calls
the TLS ULP setsockopt early in TLS handshake but only enables
the TLS TX path once the handshake has completed. As a result the
datapath missed the initial handshake messages.
Fixes:
02c558b2d5d6 ("bpf: sockmap, support for msg_peek in sk_msg with redirect ingress")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Thu, 20 Dec 2018 19:35:35 +0000 (11:35 -0800)]
bpf: sk_msg, sock{map|hash} redirect through ULP
A sockmap program that redirects through a kTLS ULP enabled socket
will not work correctly because the ULP layer is skipped. This
fixes the behavior to call through the ULP layer on redirect to
ensure any operations required on the data stream at the ULP layer
continue to be applied.
To do this we add an internal flag MSG_SENDPAGE_NOPOLICY to avoid
calling the BPF layer on a redirected message. This is
required to avoid calling the BPF layer multiple times (possibly
recursively) which is not the current/expected behavior without
ULPs. In the future we may add a redirect flag if users _do_
want the policy applied again but this would need to work for both
ULP and non-ULP sockets and be opt-in to avoid breaking existing
programs.
Also to avoid polluting the flag space with an internal flag we
reuse the flag space overlapping MSG_SENDPAGE_NOPOLICY with
MSG_WAITFORONE. Here WAITFORONE is specific to recv path and
SENDPAGE_NOPOLICY is only used for sendpage hooks. The last thing
to verify is user space API is masked correctly to ensure the flag
can not be set by user. (Note this needs to be true regardless
because we have internal flags already in-use that user space
should not be able to set). But for completeness we have two UAPI
paths into sendpage, sendfile and splice.
In the sendfile case the function do_sendfile() zero's flags,
./fs/read_write.c:
static ssize_t do_sendfile(int out_fd, int in_fd, loff_t *ppos,
size_t count, loff_t max)
{
...
fl = 0;
#if 0
/*
* We need to debate whether we can enable this or not. The
* man page documents EAGAIN return for the output at least,
* and the application is arguably buggy if it doesn't expect
* EAGAIN on a non-blocking file descriptor.
*/
if (in.file->f_flags & O_NONBLOCK)
fl = SPLICE_F_NONBLOCK;
#endif
file_start_write(out.file);
retval = do_splice_direct(in.file, &pos, out.file, &out_pos, count, fl);
}
In the splice case the pipe_to_sendpage "actor" is used which
masks flags with SPLICE_F_MORE.
./fs/splice.c:
static int pipe_to_sendpage(struct pipe_inode_info *pipe,
struct pipe_buffer *buf, struct splice_desc *sd)
{
...
more = (sd->flags & SPLICE_F_MORE) ? MSG_MORE : 0;
...
}
Confirming what we expect that internal flags are in fact internal
to socket side.
Fixes:
d3b18ad31f93 ("tls: add bpf support to sk_msg handling")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Thu, 20 Dec 2018 19:35:34 +0000 (11:35 -0800)]
bpf: sk_msg, zap ingress queue on psock down
In addition to releasing any cork'ed data on a psock when the psock
is removed we should also release any skb's in the ingress work queue.
Otherwise the skb's eventually get free'd but late in the tear
down process so we see the WARNING due to non-zero sk_forward_alloc.
void sk_stream_kill_queues(struct sock *sk)
{
...
WARN_ON(sk->sk_forward_alloc);
...
}
Fixes:
604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Thu, 20 Dec 2018 19:35:33 +0000 (11:35 -0800)]
bpf: sk_msg, fix socket data_ready events
When a skb verdict program is in-use and either another BPF program
redirects to that socket or the new SK_PASS support is used the
data_ready callback does not wake up application. Instead because
the stream parser/verdict is using the sk data_ready callback we wake
up the stream parser/verdict block.
Fix this by adding a helper to check if the stream parser block is
enabled on the sk and if so call the saved pointer which is the
upper layers wake up function.
This fixes application stalls observed when an application is waiting
for data in a blocking read().
Fixes:
d829e9c4112b ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Thu, 20 Dec 2018 19:35:32 +0000 (11:35 -0800)]
bpf: skb_verdict, support SK_PASS on RX BPF path
Add SK_PASS verdict support to SK_SKB_VERDICT programs. Now that
support for redirects exists we can implement SK_PASS as a redirect
to the same socket. This simplifies the BPF programs and avoids an
extra map lookup on RX path for simple visibility cases.
Further, reduces user (BPF programmer in this context) confusion
when their program drops skb due to lack of support.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Thu, 20 Dec 2018 19:35:31 +0000 (11:35 -0800)]
bpf: skmsg, replace comments with BUILD bug
Enforce comment on structure layout dependency with a BUILD_BUG_ON
to ensure the condition is maintained.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Thu, 20 Dec 2018 19:35:30 +0000 (11:35 -0800)]
bpf: sk_msg, improve offset chk in _is_valid_access
The check for max offset in sk_msg_is_valid_access uses sizeof()
which is incorrect because it would allow accessing possibly
past the end of the struct in the padded case. Further, it doesn't
preclude accessing any padding that may be added in the middle of
a struct. All told this makes it fragile to rely on.
To fix this explicitly check offsets with fields using the
bpf_ctx_range() and bpf_ctx_range_till() macros.
For reference the current structure layout looks as follows (reported
by pahole)
struct sk_msg_md {
union {
void * data; /* 8 */
}; /* 0 8 */
union {
void * data_end; /* 8 */
}; /* 8 8 */
__u32 family; /* 16 4 */
__u32 remote_ip4; /* 20 4 */
__u32 local_ip4; /* 24 4 */
__u32 remote_ip6[4]; /* 28 16 */
__u32 local_ip6[4]; /* 44 16 */
__u32 remote_port; /* 60 4 */
/* --- cacheline 1 boundary (64 bytes) --- */
__u32 local_port; /* 64 4 */
__u32 size; /* 68 4 */
/* size: 72, cachelines: 2, members: 10 */
/* last cacheline: 8 bytes */
};
So there should be no padding at the moment but fixing this now
prevents future errors.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
John Fastabend [Thu, 20 Dec 2018 19:35:29 +0000 (11:35 -0800)]
bpf: sk_msg, fix sk_msg_md access past end test
Currently, the test to ensure reads past the end of the sk_msg_md
data structure fail is incorrectly expecting success. Fix this
typo and use correct expected error.
Fixes:
945a47d87cee ("bpf: sk_msg, add tests for size field")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jesper Dangaard Brouer [Wed, 19 Dec 2018 16:00:23 +0000 (17:00 +0100)]
bpf/cpumap: make sure frame_size for build_skb is aligned if headroom isn't
The frame_size passed to build_skb must be aligned, else it is
possible that the embedded struct skb_shared_info gets unaligned.
For correctness make sure that xdpf->headroom in included in the
alignment. No upstream drivers can hit this, as all XDP drivers provide
an aligned headroom. This was discovered when playing with implementing
XDP support for mvneta, which have a 2 bytes DSA header, and this
Marvell ARM64 platform didn't like doing atomic operations on an
unaligned skb_shinfo(skb)->dataref addresses.
Fixes:
1c601d829ab0 ("bpf: cpumap xdp_buff to skb conversion and allocation")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Steve Douthit [Thu, 6 Dec 2018 15:50:43 +0000 (15:50 +0000)]
ixgbe: use mii_bus to handle MII related ioctls
Use the mii_bus callbacks to address the entire clause 22/45 address
space. Enables userspace to poke switch registers instead of a single
PHY address.
The ixgbe firmware may be polling PHYs in a way that is not protected by
the mii_bus lock. This isn't new behavior, but as Andrew Lunn pointed
out there are more addresses available for conflicts.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Steve Douthit [Thu, 6 Dec 2018 15:50:39 +0000 (15:50 +0000)]
ixgbe: register a mdiobus
Most dsa devices expect a 'struct mii_bus' pointer to talk to switches
via the MII interface.
While this works for dsa devices, it will not work safely with Linux
PHYs in all configurations since the firmware of the ixgbe device may
be polling some PHY addresses in the background.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kai-Heng Feng [Mon, 3 Dec 2018 05:54:38 +0000 (13:54 +0800)]
igb: Fix an issue that PME is not enabled during runtime suspend
I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.
Since commit
42eca2302146 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.
To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.
Fixes:
42eca2302146 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Young Xiao [Thu, 29 Nov 2018 01:54:10 +0000 (01:54 +0000)]
ice: Do not enable NAPI on q_vectors that have no rings
If ice driver has q_vectors w/ active NAPI that has no rings,
then this will result in a divide by zero error. To correct it
I am updating the driver code so that we only support NAPI on
q_vectors that have 1 or more rings allocated to them.
See commit
13a8cd191a2b ("i40e: Do not enable NAPI on q_vectors
that have no rings") for detail.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Miroslav Lichvar [Wed, 28 Nov 2018 16:07:49 +0000 (17:07 +0100)]
i40e: extend PTP gettime function to read system clock
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Konstantin Khorenko [Fri, 23 Nov 2018 16:10:28 +0000 (19:10 +0300)]
i40e: define proper net_device::neigh_priv_len
Out of bound read reported by KASan.
i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as
tbl->entry_size + dev->neigh_priv_len
where "dev" is a net_device.
But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
YueHaibing [Mon, 19 Nov 2018 12:48:19 +0000 (20:48 +0800)]
e100: Fix passing zero to 'PTR_ERR' warning in e100_load_ucode_wait
Fix a static code checker warning:
drivers/net/ethernet/intel/e100.c:1349
e100_load_ucode_wait() warn: passing zero to 'PTR_ERR'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Thu, 20 Dec 2018 18:53:28 +0000 (10:53 -0800)]
Merge git://git./linux/kernel/git/davem/net
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Vinicius Costa Gomes [Sat, 17 Nov 2018 00:19:24 +0000 (16:19 -0800)]
Documentation: igb: Add a section about CBS
Add some pointers to the definition of the CBS algorithm, and some
notes about the limits of its implementation in the i210 family of
controllers.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesus Sanchez-Palencia [Sat, 17 Nov 2018 00:19:23 +0000 (16:19 -0800)]
igb: Change RXPBSIZE size when setting Qav mode
Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.
The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher [Thu, 2 Aug 2018 17:13:10 +0000 (10:13 -0700)]
igb: reduce CPU0 latency when updating statistics
This change is based off of the work and suggestion of Jan Jablonsky
<jan.jablonsky@thalesgroup.com>.
The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
on CPU0.
In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.
CC: Bernhard Kaindl <bernhard.kaindl@thalesgroup.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kalle Valo [Thu, 20 Dec 2018 17:25:43 +0000 (19:25 +0200)]
Merge ath-next from git://git./linux/kernel/git/kvalo/ath.git
ath.git patches for 4.21. Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
Bhagavathi Perumal S [Thu, 20 Dec 2018 12:26:00 +0000 (14:26 +0200)]
ath10k: add support to configure BB timing over wmi
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bhagavathi Perumal S [Thu, 20 Dec 2018 12:25:43 +0000 (14:25 +0200)]
dt-bindings: net: ath10k: add new dt entry to identify external FEM
This adds new dt entry ext-fem-name, it is used by ath10k driver
to select correct timing parameters and configure it in target wifi hardware.
The Front End Module(FEM) normally includes tx power amplifier(PA) and
rx low noise amplifier(LNA). The default timing parameters like tx end to
PA off timing values were fine tuned for internal FEM used in reference
design. And these timing values can not be same if ODM modifies hardware
design with different external FEM. This DT entry helps to choose correct
timing values in driver if different external FEM hardware used.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bhagavathi Perumal S [Thu, 20 Dec 2018 12:25:32 +0000 (14:25 +0200)]
dt-bindings: net: ath10k: fix node name and device type in qcom ath10k example
In qcom,ath10k documentation, ath10k is used as node name in the example of
pci based device. Normally, node name should be class of device and not the
model name, so fix it to node name "wifi". And remove the property device_type
pci since only pci bridges should have this property.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zhi Chen [Thu, 20 Dec 2018 12:25:18 +0000 (14:25 +0200)]
ath10k: fix tx_stats memory leak
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zhi Chen [Thu, 20 Dec 2018 12:24:43 +0000 (14:24 +0200)]
ath10k: fix peer stats null pointer dereference
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Dec 2018 12:24:23 +0000 (14:24 +0200)]
dt: bindings: ath10k: add bindings for wifi iommu node
WCN3990 wifi module can optionally make use of the IOMMU.
Add binding documentation for phandle to the IOMMU and
the stream id of wifi iommu block.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Dec 2018 12:24:10 +0000 (14:24 +0200)]
dt: bindings: ath10k: add missing dt properties for WCN3990 wifi node
Add missing optional properties in WCN3990 wifi node.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter [Thu, 20 Dec 2018 07:53:45 +0000 (09:53 +0200)]
ath10k: remove an unnecessary NULL check
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Dec 2018 07:53:43 +0000 (09:53 +0200)]
ath10k: move non-fatal warn logs to dbg level
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc
a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc
a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter [Thu, 20 Dec 2018 07:53:41 +0000 (09:53 +0200)]
ath10k: fix a NULL vs IS_ERR() check
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes:
ba94c753ccb4 ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Dec 2018 07:53:36 +0000 (09:53 +0200)]
ath10k: remove work in progress logs from snoc driver
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bhagavathi Perumal S [Thu, 20 Dec 2018 07:53:34 +0000 (09:53 +0200)]
ath10k: fix warning due to msdu limit error
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sathishkumar Muruganandam [Thu, 20 Dec 2018 07:53:30 +0000 (09:53 +0200)]
ath10k: disable 4addr source port learning in 10.4 FW by default
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Anilkumar Kolli [Thu, 20 Dec 2018 07:53:28 +0000 (09:53 +0200)]
ath10k: report tx rate using ieee80211_tx_rate_update()
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yu Wang [Thu, 20 Dec 2018 07:53:26 +0000 (09:53 +0200)]
ath10k: add amsdu support for monitor mode
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Karthikeyan Periyasamy [Thu, 20 Dec 2018 07:53:17 +0000 (09:53 +0200)]
ath10k: fix kernel panic due to use after free
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address
00000286
pgd =
d8754000
[
00000286] *pgd=
00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task:
dc44cac0 ti:
d4a38000 task.ti:
d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<
c02bdc50>] lr : [<
bf916b78>] psr:
20000013
sp :
d4a39b88 ip :
00000000 fp :
00000001
r10:
00000000 r9 :
1d3bc000 r8 :
00000dc0
r7 :
000080d0 r6 :
d4a38000 r5 :
dd401b00 r4 :
00000286
r3 :
00000000 r2 :
d4a39ba0 r1 :
000080d0 r0 :
dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control:
10c5787d Table:
5a75406a DAC:
00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<
c02bdc50>] (kmem_cache_alloc) from [<
bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<
bf916b78>] (ath10k_sta_state [ath10k_core]) from [<
bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<
bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<
bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<
bf88634c>] (ieee80211_add_station [mac80211]) from [<
bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<
bf83f3c4>] (nl80211_new_station [cfg80211]) from [<
bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<
bf6c4040>] (extack_doit [compat]) from [<
c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<
c05c285c>] (genl_rcv_msg) from [<
c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<
c05c1d98>] (netlink_rcv_skb) from [<
c05c25d4>] (genl_rcv+0x20/0x34)
[<
c05c25d4>] (genl_rcv) from [<
c05c1750>] (netlink_unicast+0x11c/0x204)
[<
c05c1750>] (netlink_unicast) from [<
c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<
c05c1be0>] (netlink_sendmsg) from [<
c0587e90>] (sock_sendmsg+0x70/0x84)
[<
c0587e90>] (sock_sendmsg) from [<
c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<
c058970c>] (___sys_sendmsg.part.3) from [<
c058a594>] (__sys_sendmsg+0x4c/0x70)
[<
c058a594>] (__sys_sendmsg) from [<
c0208c80>] (ret_fast_syscall+0x0/0x44)
Code:
ebfffec1 e1a04000 ea00001b e5953014 (
e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes:
a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Thu, 20 Dec 2018 07:53:10 +0000 (09:53 +0200)]
ath10k: remove set but not used variable 'num_tdls_vifs'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea95 ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Borkmann [Thu, 20 Dec 2018 16:28:29 +0000 (17:28 +0100)]
Merge branch 'bpf-jset-verifier'
Jakub Kicinski says:
====================
This is a v2 of the patch set to teach the verifier about BPF_JSET
instruction. There is also a number of tests include for both
basic functioning of the instruction and the verifier logic.
The NFP JIT handling of JSET is tweaked. Last patch adds missing
file to gitignore.
Reposting part of previous series without the dead code elimination.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 20 Dec 2018 06:13:09 +0000 (22:13 -0800)]
selftests: bpf: add missing executables to .gitignore
commit
435f90a338ae ("selftests/bpf: add a test case for sock_ops
perf-event notification") missed adding new test to gitignore.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 20 Dec 2018 06:13:08 +0000 (22:13 -0800)]
nfp: bpf: optimize codegen for JSET with a constant
The top word of the constant can only have bits set if sign
extension set it to all-1, therefore we don't really have to
mask the top half of the register. We can just OR it into
the result as is.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 20 Dec 2018 06:13:07 +0000 (22:13 -0800)]
nfp: bpf: remove the trivial JSET optimization
The verifier will now understand the JSET instruction, so don't
mark the dead branch in the JIT as noop. We won't generate any
code, anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 20 Dec 2018 06:13:06 +0000 (22:13 -0800)]
bpf: verifier: reorder stack size check with dead code sanitization
Reorder the calls to check_max_stack_depth() and sanitize_dead_code()
to separate functions which can rewrite instructions from pure checks.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 20 Dec 2018 06:13:05 +0000 (22:13 -0800)]
selftests: bpf: verifier: add tests for JSET interpretation
Validate that the verifier reasons correctly about the bounds
and removes dead code based on results of JSET instruction.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 20 Dec 2018 06:13:04 +0000 (22:13 -0800)]
bpf: verifier: teach the verifier to reason about the BPF_JSET instruction
Some JITs (nfp) try to optimize code on their own. It could make
sense in case of BPF_JSET instruction which is currently not interpreted
by the verifier, meaning for instance that dead could would not be
detected if it was under BPF_JSET branch.
Teach the verifier basics of BPF_JSET, JIT optimizations will be
removed shortly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 20 Dec 2018 06:13:03 +0000 (22:13 -0800)]
selftests: bpf: add trivial JSET tests
We seem to have no JSET instruction test, and LLVM does not
generate it at all, so let's add a simple hand-coded test
to make sure JIT implementations are correct.
v2:
- extend test_verifier to handle multiple inputs and
add the sample there (Daniel)
- add a sign extension case
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
David S. Miller [Thu, 20 Dec 2018 16:26:16 +0000 (08:26 -0800)]
Merge branch 'bnxt_en-next'
Michael Chan says:
====================
bnxt_en: Update for net-next.
Three main changes in this series, besides the usual firmware spec
update:
1. Add support for a new firmware communication channel direct to the
firmware processor that handles flow offloads. This speeds up
flow offload operations.
2. Use 64-bit internal flow handles to increase the number of flows
that can be offloaded.
3. Add level-2 context memory paging so that we can configure more
context memory for RDMA on the 57500 chips. Allocate more context
memory if RDMA is enabled on the 57500 chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 20 Dec 2018 08:38:53 +0000 (03:38 -0500)]
bnxt_en: Adjust default RX coalescing ticks to 10 us.
For a little better performance on faster machines and faster link
speeds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Venkat Duvvuru [Thu, 20 Dec 2018 08:38:52 +0000 (03:38 -0500)]
bnxt_en: Support for 64-bit flow handle.
Older firmware only supports 16-bit flow handle, because of which the
number of flows that can be offloaded can’t scale beyond a point.
Newer firmware supports 64-bit flow handle enabling the host to scale
upto millions of flows. With the new 64-bit flow handle support, driver
has to query flow stats in a different way compared to the older approach.
This patch adds support for 64-bit flow handle and new way to query
flow stats.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 20 Dec 2018 08:38:51 +0000 (03:38 -0500)]
bnxt_en: Increase context memory allocations on 57500 chips for RDMA.
If RDMA is supported on the 57500 chip, increase context memory
allocations for the resources used by RDMA.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>