drm/edid: Avoid multiple log lines for HFVSDB parsing

Replace multiple log lines with a single log line at the end of
parsing HF-VSDB. Also use drm_dbg_kms instead of DRM_DBG_KMS, and
add log for DSC1.2 support.

v2: Fixed the formatting issues in the logging (Jani).

Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916100551.2531750-5-ankit.k.nautiyal@intel.com

drm/edid: Refactor HFVSDB parsing for DSC1.2

DSC capabilities are given in bytes 11-13 of VSDB (i.e. bytes 8-10 of
SCDS). Since minimum length of Data block is 7, all bytes greater than 7
must be read only after checking the length of the data block.

This patch adds check for data block length before reading relavant DSC
bytes.

Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916100551.2531750-4-ankit.k.nautiyal@intel.com

drm/edid: Split DSC parsing into separate function

Move the DSC parsing logic into separate function.

v2: Rebase.

Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916100551.2531750-3-ankit.k.nautiyal@intel.com

drm/edid: Fix minimum bpc supported with DSC1.2 for HDMI sink

HF-VSDB/SCDB has bits to advertise support for 16, 12 and 10 bpc.
If none of the bits are set, the minimum bpc supported with DSC is 8.

This patch corrects the min bpc supported to be 8, instead of 0.

Fixes: 76ee7b905678 ("drm/edid: Parse DSC1.2 cap fields from HFVSDB block")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2: s/DSC1.2/DSC 1.2

Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916100551.2531750-2-ankit.k.nautiyal@intel.com

drm: document uAPI page-flip flags

Document flags accepted by the page-flip and atomic IOCTLs.

v2 (Pekka):
- Mention DRM_EVENT_FLIP_COMPLETE in DRM_MODE_PAGE_FLIP_EVENT docs.
- Expand DRM_MODE_ATOMIC_NONBLOCK and DRM_MODE_ATOMIC_ALLOW_MODESET
  description.
v3:
- Fix struct field ref syntax (Daniel)
- Clarify when artifacts are no longer displayed (Daniel)
- Add note about sinks deciding to show artifacts on their own (Pekka, Daniel)
v4:
- Fix typo (Pekka)

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/505107/

drm/edid: fix repeated words in comments

Delete the redundant word 'on'.

Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907113644.32831-1-yuanjilin@cdjrlc.com

drm/bridge: it6505: Add pre_enable/post_disable callback

Add atomic_pre_enable and atomic_post_disable callback to make sure the
bridge is not powered off until atomic_post_disable is called. This
prevents a power leakage when it6505 is powered off, but the upstream
DRM bridge is still sending display signals.

Fixes: b5c84a9edcd4 ("drm/bridge: add it6505 driver")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221004044943.2407781-3-treapking@chromium.org

drm/bridge: it6505: Adapt runtime power management framework

Use pm_runtime_(get|put)_sync to control the bridge power, and add
SET_SYSTEM_SLEEP_PM_OPS with pm_runtime_force_(suspend|resume) to it6505
driver. Without SET_SYSTEM_SLEEP_PM_OPS, the bridge will be powered on
unnecessarily when no external display is connected.

Fixes: b5c84a9edcd4 ("drm/bridge: add it6505 driver")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221004044943.2407781-2-treapking@chromium.org

drm/panel: ws2401: Silent no spi_device_id warning

Add spi_device_id entries to silent following SPI warning:

SPI driver ws2401-panel has no spi_device_id for samsung,lms380kf01

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220915163437.2519754-1-weiyongjun@huaweicloud.com

drm/panel: tpg110: Silent no spi_device_id warning

Add spi_device_id entries to silent following SPI warning:

SPI driver tpo-tpg110-panel has no spi_device_id for tpo,tpg110

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220915163431.2519736-1-weiyongjun@huaweicloud.com

drm/panel: db7430: Silent no spi_device_id warning

Add spi_device_id entries to silent following SPI warning:

SPI driver db7430-panel has no spi_device_id for samsung,lms397kf04

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220915163156.2519577-1-weiyongjun@huaweicloud.com

drm/sched: Add FIFO sched policy to run queue

When many entities are competing for the same run queue
on the same scheduler, we observe an unusually long wait
times and some jobs get starved. This has been observed on GPUVis.

The issue is due to the Round Robin policy used by schedulers
to pick up the next entity's job queue for execution. Under stress
of many entities and long job queues within entity some
jobs could be stuck for very long time in it's entity's
queue before being popped from the queue and executed
while for other entities with smaller job queues a job
might execute earlier even though that job arrived later
then the job in the long queue.

Fix:
Add FIFO selection policy to entities in run queue, chose next entity
on run queue in such order that if job on one entity arrived
earlier then job on another entity the first job will start
executing earlier regardless of the length of the entity's job
queue.

v2:
Switch to rb tree structure for entities based on TS of
oldest job waiting in the job queue of an entity. Improves next
entity extraction to O(1). Entity TS update
O(log N) where N is the number of entities in the run-queue

Drop default option in module control parameter.

v3:
Various cosmetical fixes and minor refactoring of fifo update function. (Luben)

v4:
Switch drm_sched_rq_select_entity_fifo to in order search (Luben)

v5: Fix up drm_sched_rq_select_entity_fifo loop (Luben)

v6: Add missing drm_sched_rq_remove_fifo_locked

v7: Fix ts sampling bug and more cosmetic stuff (Luben)

v8: Fix module parameter string (Luben)

Cc: Luben Tuikov <luben.tuikov@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Direct Rendering Infrastructure - Development <dri-devel@lists.freedesktop.org>
Cc: AMD Graphics <amd-gfx@lists.freedesktop.org>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Tested-by: Yunxiang Li (Teddy) <Yunxiang.Li@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220930041258.1050247-1-luben.tuikov@amd.com

drm/panel: simple: Use dev_err_probe() to simplify code

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs.

Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929015503.17301-3-yuancan@huawei.com

drm/panel: panel-edp: Use dev_err_probe() to simplify code

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs.

Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929015503.17301-2-yuancan@huawei.com
Link: https://patchwork.freedesktop.org/patch/msgid/20220929015503.17301-2-yuancan@huawei.com

drm/panel: simple: Add Multi-Inno Technology MI0800FT-9

Add Multi-Inno Technology MI0800FT-9 8" 800x600 DPI panel support.

Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220812114832.4946-1-cniedermaier@dh-electronics.com

dt-bindings: display: simple: Add Multi-Inno Technology MI0800FT-9 panel

Add Multi-Inno Technology MI0800FT-9 8" 800x600 DPI panel
compatible string.

Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220812114600.4895-1-cniedermaier@dh-electronics.com

drm/bridge: lt8912b: fix corrupted image output

Correct I2C address for the register list in lt8912_write_lvds_config(),
these registers are on the first I2C address (0x48), the current
function is just writing garbage to the wrong registers and this creates
multiple issues (artifacts and output completely corrupted) on some HDMI
displays.

Correct I2C address comes from Lontium documentation and it is the one
used on other out-of-tree LT8912B drivers [1].

[1] https://github.com/boundarydevices/linux/blob/boundary-imx_5.10.x_2.0.0/drivers/video/lt8912.c#L296

Fixes: 30e2ae943c26 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922124306.34729-4-dev@pschenker.ch
Link: https://patchwork.freedesktop.org/patch/msgid/20220922124306.34729-5-dev@pschenker.ch

drm/bridge: lt8912b: set hdmi or dvi mode

The Lontium LT8912 does have a setting for DVI or HDMI. This patch reads
from EDID what the display needs and sets it accordingly.

Fixes: 30e2ae943c26 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922124306.34729-3-dev@pschenker.ch

drm/bridge: lt8912b: add vsync hsync

Currently the bridge driver does not take care whether or not the display
needs positive/negative vertical/horizontal syncs. Pass these two flags
to the bridge from the EDID that was read out from the display.

Fixes: 30e2ae943c26 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922124306.34729-2-dev@pschenker.ch

drm/dp: Don't rewrite link config when setting phy test pattern

The sequence for Source DP PHY CTS automation is [2][1]:
1- Emulate successful Link Training(LT)
2- Short HPD and change link rates and number of lanes by LT.
(This is same flow for Link Layer CTS)
3- Short HPD and change PHY test pattern and swing/pre-emphasis
levels (This step should not trigger LT)

The problem is with DP PHY compliance setup as follow:

     [DPTX + on board LTTPR]------Main Link--->[Scope]
                    ^                         |
|                         |
|                         |
----------Aux Ch------>[Aux Emulator]

At step 3, before writing TRAINING_LANEx_SET/LINK_QUAL_PATTERN_SET
to declare the pattern/swing requested by scope, we write link
config in LINK_BW_SET/LANE_COUNT_SET on a port that has LTTPR.
As LTTPR snoops aux transaction, LINK_BW_SET/LANE_COUNT_SET writes
indicate a LT will start [Check DP 2.0 E11 -Sec 3.6.8.2 & 3.6.8.6.3],
and LTTPR will reset the link and stop sending DP signals to
DPTX/Scope causing the measurements to fail. Note that step 3 will
not trigger LT and DP link will never recovered by the
Aux Emulator/Scope.

The reset of link can be tested with a monitor connected to LTTPR
port simply by writing to LINK_BW_SET or LANE_COUNT_SET as follow

  igt/tools/dpcd_reg write --offset=0x100 --value 0x14 --device=2

OR

  printf '\x14' | sudo dd of=/dev/drm_dp_aux2 bs=1 count=1 conv=notrunc
  seek=$((0x100))

This single aux write causes the screen to blank, sending short HPD to
DPTX, setting LINK_STATUS_UPDATE = 1 in DPCD 0x204, and triggering LT.

As stated in [1]:
"Before any TX electrical testing can be performed, the link between a
DPTX and DPRX (in this case, a piece of test equipment), including all
LTTPRs within the path, shall be trained as defined in this Standard."

In addition, changing Phy pattern/Swing/Pre-emphasis (Step 3) uses the
same link rate and lane count applied on step 2, so no need to redo LT.

The fix is to not rewrite link config in step 3, and just writes
TRAINING_LANEx_SET and LINK_QUAL_PATTERN_SET

[1]: DP 2.0 E11 - 3.6.11.1 LTTPR DPTX_PHY Electrical Compliance

[2]: Configuring UnigrafDPTC Controller - Automation Test Sequence
https://www.keysight.com/us/en/assets/9922-01244/help-files/
D9040DPPC-DisplayPort-Test-Software-Online-Help-latest.chm

Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Or Cochvi <or.cochvi@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916054900.415804-1-khaled.almahallawy@intel.com

drm/framebuffer: convert to drm_dbg_kms()

Replace DRM_DEBUG_KMS() with drm_dbg_kms() which allows specifying
the DRM device to provide more context.

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905103559.118561-1-contact@emersion.fr

drm/format-helper: Add KUnit tests for drm_fb_xrgb8888_to_gray8()

Extend the existing test cases to test the conversion from XRGB8888 to
grayscale.

Tested-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220926080837.65734-4-jose.exposito89@gmail.com

drm/format-helper: Add KUnit tests for drm_fb_xrgb8888_to_xrgb2101010()

Extend the existing test cases to test the conversion from XRGB8888 to
XRGB2101010.

In order to be able to call drm_fb_xrgb8888_to_xrgb2101010() when
compiling CONFIG_DRM_KMS_HELPER as a module export the symbol.

Tested-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220926080837.65734-3-jose.exposito89@gmail.com

drm/format-helper: Add KUnit tests for drm_fb_xrgb8888_to_rgb888()

Extend the existing test cases to test the conversion from XRGB8888 to
RGB888.

Tested-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: David Gow <davidgow@google.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220926080837.65734-2-jose.exposito89@gmail.com

drm/panel-edp: Add BOE NT116WHM-N4C (HW: V8.1)

Add support for the BOE - NT116WHM-N4C (HW: V8.1) panel.

Signed-off-by: Sean Hong <sean.hong@quanta.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927063524.493591-1-sean.hong@quanta.corp-partner.google.com

drm/panel-edp: Fix delays for INX N116BCA-EA2 (HW: C1)

This panel has the same delay timing as N116BCA-EA1. So, fix the
delay timing from delay_200_500_p2e80 to delay_200_500_e80_d50.

Fixes: c7bcc1056cff ("drm/panel-edp: Add INX N116BCA-EA2")
Signed-off-by: Sean Hong <sean.hong@quanta.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927021835.488803-1-sean.hong@quanta.corp-partner.google.com

drm/panel-edp: Fix delays for INX N116BCN-EA1 (HW: C4)

This panel has the same delay timing as N116BCA-EA1. So, fix the
delay timing from delay_200_500_p2e80 to delay_200_500_e80_d50.

Fixes: 9f4a57148120 ("drm/panel-edp: Add INX N116BCN-EA1")
Signed-off-by: Sean Hong <sean.hong@quanta.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927021021.488295-1-sean.hong@quanta.corp-partner.google.com

drm/ssd130x: Synchronize access to dma-buf imported GEM BOs

Synchronize CPU access to GEM BOs with other drivers when updating the
screen buffer. Imported DMA buffers might otherwise contain stale data.

Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927095249.1919385-1-javierm@redhat.com

drm/ssd130x: Use drm_atomic_get_new_plane_state()

The struct drm_plane .state shouldn't be accessed directly but instead the
drm_atomic_get_new_plane_state() helper function should be used.

This is based on a similar patch from Thomas Zimmermann for the simpledrm
driver. No functional changes.

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220923083447.1679780-1-javierm@redhat.com

drm/simpledrm: Synchronize access to GEM BOs

Synchronize CPU access to GEM BOs with other drivers when updating the
screen buffer. Imported buffers might otherwise contain stale data.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922130944.27138-6-tzimmermann@suse.de

drm/simpledrm: Iterate over damage clips

Iterate over all damage clips and updated them one by one. Replaces
the merging of damage areas, which can result in significant overhead
if damage areas are not close to each other.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922130944.27138-5-tzimmermann@suse.de

drm/simpledrm: Remove !fb check from atomic_update

The primary plane implements atomic_disable, so atomic_update will
not be called without a framebuffer set. Remove the test for !fb.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922130944.27138-4-tzimmermann@suse.de

drm/simpledrm: Use drm_atomic_get_new_plane_state()

Lookup the plane's state in atomic_update with the helper
drm_atomic_get_new_plane_state(). Also rename the helpers'
state arguments. No functional changes.

Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922130944.27138-3-tzimmermann@suse.de

drm/simpledrm: Compute linestride with drm_format_info_min_pitch()

If not given, compute the stride with drm_format_info_min_pitch(). It's
the standard helper for this purpose.

Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Fixes: fd9e3169e42b ("drm/simpledrm: Compute framebuffer stride if not set")
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220922130944.27138-2-tzimmermann@suse.de

drm/panel-edp: Add INX N116BCA-EA2

Add support for the INX - N116BCA-EA2 (HW: C1) panel

Signed-off-by: Sean Hong <sean.hong@quanta.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220926100839.482804-1-sean.hong@quanta.corp-partner.google.com

drm/ttm: add dma_resv_assert_held() calls to vmap/vunmap

Let's make sure nobody is calling those functions without holding the
appropriate locks.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220715111533.467012-2-christian.koenig@amd.com

drm/ast: make ast_modeset static

The symbol is not used outside of the file, so mark it static.

Fixes the following warning:

drivers/gpu/drm/ast/ast_drv.c:42:5: warning: symbol 'ast_modeset'
was not declared. Should it be static?

Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220926023253.739699-1-ruanjinjie@huawei.com

drm/panel-edp: Add AUO B116XAK01.6

Add support for the AUO - B116XAK01.6 (HW: 1A) panel.

Signed-off-by: Sean Hong <sean.hong@quanta.corp-partner.google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220923055133.302740-1-sean.hong@quanta.corp-partner.google.com

drm/panel-edp: Add BOE NT116WHM-N21

Add support for the BOE - NT116WHM-N21 (HW: V8.2) panel.

Signed-off-by: Sean Hong <sean.hong@quanta.corp-partner.google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220923054614.302440-1-sean.hong@quanta.corp-partner.google.com

drm/panel-edp: Add BOE NT116WHM-N21 (HW: V8.1)

Add support for the BOE - NT116WHM-N21 (HW: V8.1) panel.

Signed-off-by: Sean Hong <sean.hong@quanta.corp-partner.google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220923085028.306790-1-sean.hong@quanta.corp-partner.google.com

drm/panel-edp: Add INX N116BCN-EA1

Add support for the INX - N116BCN-EA1 (HW: C4) panel.

Signed-off-by: Sean Hong <sean.hong@quanta.corp-partner.google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220923053729.301626-1-sean.hong@quanta.corp-partner.google.com

virtio-gpu: fix shift wrapping bug in virtio_gpu_fence_event_create()

The ->ring_idx_mask variable is a u64 so static checkers, Smatch in
this case, complain if the BIT() is not also a u64.

drivers/gpu/drm/virtio/virtgpu_ioctl.c:50 virtio_gpu_fence_event_create()
warn: should '(1 << ring_idx)' be a 64 bit type?

Fixes: cd7f5ca33585 ("drm/virtio: implement context init: add virtio_gpu_fence_event")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/YygN7jY0GdUSQSy0@kili
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

drm/qxl: drop set_prod_notify parameter from qxl_ring_create

Since qxl_io_reset(qdev) will be called immediately
after qxl_ring_create() been called,
and parameter like notify_on_prod will be set to default value.
So the call to qxl_ring_init_hdr() before becomes meaningless.

Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Suggested-by: Ming Xie<xieming@kylinos.cn>
Link: http://patchwork.freedesktop.org/patch/msgid/20220920065023.1633303-1-zhouzongmin@kylinos.cn
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

drm/meson: remove drm bridges at aggregate driver unbind time

drm bridges added by meson_encoder_hdmi_init and meson_encoder_cvbs_init
were not manually removed at module unload time, which caused dangling
references to freed memory to remain linked in the global bridge_list.

When loading the driver modules back in, the same functions would again
call drm_bridge_add, and when traversing the global bridge_list, would
end up peeking into freed memory.

Once again KASAN revealed the problem:

[  +0.000095] =============================================================
[  +0.000008] BUG: KASAN: use-after-free in __list_add_valid+0x9c/0x120
[  +0.000018] Read of size 8 at addr ffff00003da291f0 by task modprobe/2483

[  +0.000018] CPU: 3 PID: 2483 Comm: modprobe Tainted: G         C O      5.19.0-rc6-lrmbkasan+ #1
[  +0.000011] Hardware name: Hardkernel ODROID-N2Plus (DT)
[  +0.000008] Call trace:
[  +0.000006]  dump_backtrace+0x1ec/0x280
[  +0.000012]  show_stack+0x24/0x80
[  +0.000008]  dump_stack_lvl+0x98/0xd4
[  +0.000011]  print_address_description.constprop.0+0x80/0x520
[  +0.000011]  print_report+0x128/0x260
[  +0.000008]  kasan_report+0xb8/0xfc
[  +0.000008]  __asan_report_load8_noabort+0x3c/0x50
[  +0.000009]  __list_add_valid+0x9c/0x120
[  +0.000009]  drm_bridge_add+0x6c/0x104 [drm]
[  +0.000165]  dw_hdmi_probe+0x1900/0x2360 [dw_hdmi]
[  +0.000022]  meson_dw_hdmi_bind+0x520/0x814 [meson_dw_hdmi]
[  +0.000014]  component_bind+0x174/0x520
[  +0.000012]  component_bind_all+0x1a8/0x38c
[  +0.000010]  meson_drv_bind_master+0x5e8/0xb74 [meson_drm]
[  +0.000032]  meson_drv_bind+0x20/0x2c [meson_drm]
[  +0.000027]  try_to_bring_up_aggregate_device+0x19c/0x390
[  +0.000010]  component_master_add_with_match+0x1c8/0x284
[  +0.000009]  meson_drv_probe+0x274/0x280 [meson_drm]
[  +0.000026]  platform_probe+0xd0/0x220
[  +0.000009]  really_probe+0x3ac/0xa80
[  +0.000009]  __driver_probe_device+0x1f8/0x400
[  +0.000009]  driver_probe_device+0x68/0x1b0
[  +0.000009]  __driver_attach+0x20c/0x480
[  +0.000008]  bus_for_each_dev+0x114/0x1b0
[  +0.000009]  driver_attach+0x48/0x64
[  +0.000008]  bus_add_driver+0x390/0x564
[  +0.000009]  driver_register+0x1a8/0x3e4
[  +0.000009]  __platform_driver_register+0x6c/0x94
[  +0.000008]  meson_drm_platform_driver_init+0x3c/0x1000 [meson_drm]
[  +0.000027]  do_one_initcall+0xc4/0x2b0
[  +0.000011]  do_init_module+0x154/0x570
[  +0.000011]  load_module+0x1a78/0x1ea4
[  +0.000008]  __do_sys_init_module+0x184/0x1cc
[  +0.000009]  __arm64_sys_init_module+0x78/0xb0
[  +0.000009]  invoke_syscall+0x74/0x260
[  +0.000009]  el0_svc_common.constprop.0+0xcc/0x260
[  +0.000008]  do_el0_svc+0x50/0x70
[  +0.000007]  el0_svc+0x68/0x1a0
[  +0.000012]  el0t_64_sync_handler+0x11c/0x150
[  +0.000008]  el0t_64_sync+0x18c/0x190

[  +0.000016] Allocated by task 879:
[  +0.000008]  kasan_save_stack+0x2c/0x5c
[  +0.000011]  __kasan_kmalloc+0x90/0xd0
[  +0.000007]  __kmalloc+0x278/0x4a0
[  +0.000011]  mpi_resize+0x13c/0x1d0
[  +0.000011]  mpi_powm+0xd24/0x1570
[  +0.000009]  rsa_enc+0x1a4/0x30c
[  +0.000009]  pkcs1pad_verify+0x3f0/0x580
[  +0.000009]  public_key_verify_signature+0x7a8/0xba4
[  +0.000010]  public_key_verify_signature_2+0x40/0x60
[  +0.000008]  verify_signature+0xb4/0x114
[  +0.000008]  pkcs7_validate_trust_one.constprop.0+0x3b8/0x574
[  +0.000009]  pkcs7_validate_trust+0xb8/0x15c
[  +0.000008]  verify_pkcs7_message_sig+0xec/0x1b0
[  +0.000012]  verify_pkcs7_signature+0x78/0xac
[  +0.000007]  mod_verify_sig+0x110/0x190
[  +0.000009]  module_sig_check+0x114/0x1e0
[  +0.000009]  load_module+0xa0/0x1ea4
[  +0.000008]  __do_sys_init_module+0x184/0x1cc
[  +0.000008]  __arm64_sys_init_module+0x78/0xb0
[  +0.000008]  invoke_syscall+0x74/0x260
[  +0.000009]  el0_svc_common.constprop.0+0x1a8/0x260
[  +0.000008]  do_el0_svc+0x50/0x70
[  +0.000007]  el0_svc+0x68/0x1a0
[  +0.000009]  el0t_64_sync_handler+0x11c/0x150
[  +0.000009]  el0t_64_sync+0x18c/0x190

[  +0.000013] Freed by task 2422:
[  +0.000008]  kasan_save_stack+0x2c/0x5c
[  +0.000009]  kasan_set_track+0x2c/0x40
[  +0.000007]  kasan_set_free_info+0x28/0x50
[  +0.000009]  ____kasan_slab_free+0x128/0x1d4
[  +0.000008]  __kasan_slab_free+0x18/0x24
[  +0.000007]  slab_free_freelist_hook+0x108/0x230
[  +0.000010]  kfree+0x110/0x35c
[  +0.000008]  release_nodes+0xf0/0x16c
[  +0.000009]  devres_release_group+0x180/0x270
[  +0.000008]  take_down_aggregate_device+0xcc/0x160
[  +0.000010]  component_del+0x18c/0x360
[  +0.000009]  meson_dw_hdmi_remove+0x28/0x40 [meson_dw_hdmi]
[  +0.000013]  platform_remove+0x64/0xb0
[  +0.000008]  device_remove+0xb8/0x154
[  +0.000009]  device_release_driver_internal+0x398/0x5b0
[  +0.000009]  driver_detach+0xac/0x1b0
[  +0.000009]  bus_remove_driver+0x158/0x29c
[  +0.000008]  driver_unregister+0x70/0xb0
[  +0.000009]  platform_driver_unregister+0x20/0x2c
[  +0.000007]  meson_dw_hdmi_platform_driver_exit+0x1c/0x30 [meson_dw_hdmi]
[  +0.000012]  __do_sys_delete_module+0x288/0x400
[  +0.000009]  __arm64_sys_delete_module+0x5c/0x80
[  +0.000009]  invoke_syscall+0x74/0x260
[  +0.000008]  el0_svc_common.constprop.0+0xcc/0x260
[  +0.000008]  do_el0_svc+0x50/0x70
[  +0.000007]  el0_svc+0x68/0x1a0
[  +0.000008]  el0t_64_sync_handler+0x11c/0x150
[  +0.000009]  el0t_64_sync+0x18c/0x190

[  +0.000013] The buggy address belongs to the object at ffff00003da29000
               which belongs to the cache kmalloc-1k of size 1024
[  +0.000008] The buggy address is located 496 bytes inside of
               1024-byte region [ffff00003da29000, ffff00003da29400)

[  +0.000015] The buggy address belongs to the physical page:
[  +0.000009] page:fffffc0000f68a00 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x3da28
[  +0.000012] head:fffffc0000f68a00 order:3 compound_mapcount:0 compound_pincount:0
[  +0.000009] flags: 0xffff00000010200(slab|head|node=0|zone=0|lastcpupid=0xffff)
[  +0.000019] raw: 0ffff00000010200 fffffc0000eb5c08 fffffc0000d96608 ffff000000002a80
[  +0.000008] raw: 0000000000000000 00000000000a000a 00000001ffffffff 0000000000000000
[  +0.000008] page dumped because: kasan: bad access detected

[  +0.000011] Memory state around the buggy address:
[  +0.000009]  ffff00003da29080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007]  ffff00003da29100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007] >ffff00003da29180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007]                                                              ^
[  +0.000008]  ffff00003da29200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000006]  ffff00003da29280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007] ==================================================================

Fix by keeping track of which encoders were initialised in the meson_drm
structure and manually removing their bridges at aggregate driver's unbind
time.

Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220920222842.1053234-1-adrian.larumbe@collabora.com

drm/meson: explicitly remove aggregate driver at module unload time

Because component_master_del wasn't being called when unloading the
meson_drm module, the aggregate device would linger forever in the global
aggregate_devices list. That means when unloading and reloading the
meson_dw_hdmi module, component_add would call into
try_to_bring_up_aggregate_device and find the unbound meson_drm aggregate
device.

This would in turn dereference some of the aggregate_device's struct
entries which point to memory automatically freed by the devres API when
unbinding the aggregate device from meson_drv_unbind, and trigger an
use-after-free bug:

[  +0.000014] =============================================================
[  +0.000007] BUG: KASAN: use-after-free in find_components+0x468/0x500
[  +0.000017] Read of size 8 at addr ffff000006731688 by task modprobe/2536
[  +0.000018] CPU: 4 PID: 2536 Comm: modprobe Tainted: G         C O      5.19.0-rc6-lrmbkasan+ #1
[  +0.000010] Hardware name: Hardkernel ODROID-N2Plus (DT)
[  +0.000008] Call trace:
[  +0.000005]  dump_backtrace+0x1ec/0x280
[  +0.000011]  show_stack+0x24/0x80
[  +0.000007]  dump_stack_lvl+0x98/0xd4
[  +0.000010]  print_address_description.constprop.0+0x80/0x520
[  +0.000011]  print_report+0x128/0x260
[  +0.000007]  kasan_report+0xb8/0xfc
[  +0.000007]  __asan_report_load8_noabort+0x3c/0x50
[  +0.000009]  find_components+0x468/0x500
[  +0.000008]  try_to_bring_up_aggregate_device+0x64/0x390
[  +0.000009]  __component_add+0x1dc/0x49c
[  +0.000009]  component_add+0x20/0x30
[  +0.000008]  meson_dw_hdmi_probe+0x28/0x34 [meson_dw_hdmi]
[  +0.000013]  platform_probe+0xd0/0x220
[  +0.000008]  really_probe+0x3ac/0xa80
[  +0.000008]  __driver_probe_device+0x1f8/0x400
[  +0.000008]  driver_probe_device+0x68/0x1b0
[  +0.000008]  __driver_attach+0x20c/0x480
[  +0.000009]  bus_for_each_dev+0x114/0x1b0
[  +0.000007]  driver_attach+0x48/0x64
[  +0.000009]  bus_add_driver+0x390/0x564
[  +0.000007]  driver_register+0x1a8/0x3e4
[  +0.000009]  __platform_driver_register+0x6c/0x94
[  +0.000007]  meson_dw_hdmi_platform_driver_init+0x30/0x1000 [meson_dw_hdmi]
[  +0.000014]  do_one_initcall+0xc4/0x2b0
[  +0.000008]  do_init_module+0x154/0x570
[  +0.000010]  load_module+0x1a78/0x1ea4
[  +0.000008]  __do_sys_init_module+0x184/0x1cc
[  +0.000008]  __arm64_sys_init_module+0x78/0xb0
[  +0.000008]  invoke_syscall+0x74/0x260
[  +0.000008]  el0_svc_common.constprop.0+0xcc/0x260
[  +0.000009]  do_el0_svc+0x50/0x70
[  +0.000008]  el0_svc+0x68/0x1a0
[  +0.000009]  el0t_64_sync_handler+0x11c/0x150
[  +0.000009]  el0t_64_sync+0x18c/0x190

[  +0.000014] Allocated by task 902:
[  +0.000007]  kasan_save_stack+0x2c/0x5c
[  +0.000009]  __kasan_kmalloc+0x90/0xd0
[  +0.000007]  __kmalloc_node+0x240/0x580
[  +0.000010]  memcg_alloc_slab_cgroups+0xa4/0x1ac
[  +0.000010]  memcg_slab_post_alloc_hook+0xbc/0x4c0
[  +0.000008]  kmem_cache_alloc_node+0x1d0/0x490
[  +0.000009]  __alloc_skb+0x1d4/0x310
[  +0.000010]  alloc_skb_with_frags+0x8c/0x620
[  +0.000008]  sock_alloc_send_pskb+0x5ac/0x6d0
[  +0.000010]  unix_dgram_sendmsg+0x2e0/0x12f0
[  +0.000010]  sock_sendmsg+0xcc/0x110
[  +0.000007]  sock_write_iter+0x1d0/0x304
[  +0.000008]  new_sync_write+0x364/0x460
[  +0.000007]  vfs_write+0x420/0x5ac
[  +0.000008]  ksys_write+0x19c/0x1f0
[  +0.000008]  __arm64_sys_write+0x78/0xb0
[  +0.000007]  invoke_syscall+0x74/0x260
[  +0.000008]  el0_svc_common.constprop.0+0x1a8/0x260
[  +0.000009]  do_el0_svc+0x50/0x70
[  +0.000007]  el0_svc+0x68/0x1a0
[  +0.000008]  el0t_64_sync_handler+0x11c/0x150
[  +0.000008]  el0t_64_sync+0x18c/0x190

[  +0.000013] Freed by task 2509:
[  +0.000008]  kasan_save_stack+0x2c/0x5c
[  +0.000007]  kasan_set_track+0x2c/0x40
[  +0.000008]  kasan_set_free_info+0x28/0x50
[  +0.000008]  ____kasan_slab_free+0x128/0x1d4
[  +0.000008]  __kasan_slab_free+0x18/0x24
[  +0.000007]  slab_free_freelist_hook+0x108/0x230
[  +0.000010]  kfree+0x110/0x35c
[  +0.000008]  release_nodes+0xf0/0x16c
[  +0.000008]  devres_release_all+0xfc/0x180
[  +0.000008]  device_unbind_cleanup+0x24/0x164
[  +0.000008]  device_release_driver_internal+0x3e8/0x5b0
[  +0.000010]  driver_detach+0xac/0x1b0
[  +0.000008]  bus_remove_driver+0x158/0x29c
[  +0.000008]  driver_unregister+0x70/0xb0
[  +0.000009]  platform_driver_unregister+0x20/0x2c
[  +0.000007]  0xffff800003722d98
[  +0.000012]  __do_sys_delete_module+0x288/0x400
[  +0.000009]  __arm64_sys_delete_module+0x5c/0x80
[  +0.000008]  invoke_syscall+0x74/0x260
[  +0.000008]  el0_svc_common.constprop.0+0xcc/0x260
[  +0.000008]  do_el0_svc+0x50/0x70
[  +0.000007]  el0_svc+0x68/0x1a0
[  +0.000008]  el0t_64_sync_handler+0x11c/0x150
[  +0.000009]  el0t_64_sync+0x18c/0x190

[  +0.000013] Last potentially related work creation:
[  +0.000007]  kasan_save_stack+0x2c/0x5c
[  +0.000007]  __kasan_record_aux_stack+0xb8/0xf0
[  +0.000009]  kasan_record_aux_stack_noalloc+0x14/0x20
[  +0.000008]  insert_work+0x54/0x290
[  +0.000009]  __queue_work+0x48c/0xd24
[  +0.000008]  queue_work_on+0x90/0x11c
[  +0.000008]  call_usermodehelper_exec+0x188/0x404
[  +0.000010]  kobject_uevent_env+0x5a8/0x794
[  +0.000010]  kobject_uevent+0x14/0x20
[  +0.000008]  driver_register+0x230/0x3e4
[  +0.000009]  __platform_driver_register+0x6c/0x94
[  +0.000007]  gxbb_driver_init+0x28/0x34
[  +0.000010]  do_one_initcall+0xc4/0x2b0
[  +0.000008]  do_initcalls+0x20c/0x24c
[  +0.000010]  kernel_init_freeable+0x22c/0x278
[  +0.000009]  kernel_init+0x3c/0x170
[  +0.000008]  ret_from_fork+0x10/0x20

[  +0.000013] The buggy address belongs to the object at ffff000006731600
               which belongs to the cache kmalloc-256 of size 256
[  +0.000009] The buggy address is located 136 bytes inside of
               256-byte region [ffff000006731600, ffff000006731700)

[  +0.000015] The buggy address belongs to the physical page:
[  +0.000008] page:fffffc000019cc00 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff000006730a00 pfn:0x6730
[  +0.000011] head:fffffc000019cc00 order:2 compound_mapcount:0 compound_pincount:0
[  +0.000008] flags: 0xffff00000010200(slab|head|node=0|zone=0|lastcpupid=0xffff)
[  +0.000016] raw: 0ffff00000010200 fffffc00000c3d08 fffffc0000ef2b08 ffff000000002680
[  +0.000009] raw: ffff000006730a00 0000000000150014 00000001ffffffff 0000000000000000
[  +0.000006] page dumped because: kasan: bad access detected

[  +0.000011] Memory state around the buggy address:
[  +0.000007]  ffff000006731580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  +0.000007]  ffff000006731600: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007] >ffff000006731680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007]                       ^
[  +0.000006]  ffff000006731700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  +0.000007]  ffff000006731780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  +0.000006] ==================================================================

Fix by adding 'remove' driver callback for meson-drm, and explicitly deleting the
aggregate device.

Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220919010940.419893-3-adrian.larumbe@collabora.com

drm/meson: reorder driver deinit sequence to fix use-after-free bug

Unloading the driver triggers the following KASAN warning:

[  +0.006275] =============================================================
[  +0.000029] BUG: KASAN: use-after-free in __list_del_entry_valid+0xe0/0x1a0
[  +0.000026] Read of size 8 at addr ffff000020c395e0 by task rmmod/2695

[  +0.000019] CPU: 5 PID: 2695 Comm: rmmod Tainted: G         C O      5.19.0-rc6-lrmbkasan+ #1
[  +0.000013] Hardware name: Hardkernel ODROID-N2Plus (DT)
[  +0.000008] Call trace:
[  +0.000007]  dump_backtrace+0x1ec/0x280
[  +0.000013]  show_stack+0x24/0x80
[  +0.000008]  dump_stack_lvl+0x98/0xd4
[  +0.000011]  print_address_description.constprop.0+0x80/0x520
[  +0.000011]  print_report+0x128/0x260
[  +0.000007]  kasan_report+0xb8/0xfc
[  +0.000008]  __asan_report_load8_noabort+0x3c/0x50
[  +0.000010]  __list_del_entry_valid+0xe0/0x1a0
[  +0.000009]  drm_atomic_private_obj_fini+0x30/0x200 [drm]
[  +0.000172]  drm_bridge_detach+0x94/0x260 [drm]
[  +0.000145]  drm_encoder_cleanup+0xa4/0x290 [drm]
[  +0.000144]  drm_mode_config_cleanup+0x118/0x740 [drm]
[  +0.000143]  drm_mode_config_init_release+0x1c/0x2c [drm]
[  +0.000144]  drm_managed_release+0x170/0x414 [drm]
[  +0.000142]  drm_dev_put.part.0+0xc0/0x124 [drm]
[  +0.000143]  drm_dev_put+0x20/0x30 [drm]
[  +0.000142]  meson_drv_unbind+0x1d8/0x2ac [meson_drm]
[  +0.000028]  take_down_aggregate_device+0xb0/0x160
[  +0.000016]  component_del+0x18c/0x360
[  +0.000009]  meson_dw_hdmi_remove+0x28/0x40 [meson_dw_hdmi]
[  +0.000015]  platform_remove+0x64/0xb0
[  +0.000009]  device_remove+0xb8/0x154
[  +0.000009]  device_release_driver_internal+0x398/0x5b0
[  +0.000009]  driver_detach+0xac/0x1b0
[  +0.000009]  bus_remove_driver+0x158/0x29c
[  +0.000009]  driver_unregister+0x70/0xb0
[  +0.000008]  platform_driver_unregister+0x20/0x2c
[  +0.000008]  meson_dw_hdmi_platform_driver_exit+0x1c/0x30 [meson_dw_hdmi]
[  +0.000012]  __do_sys_delete_module+0x288/0x400
[  +0.000011]  __arm64_sys_delete_module+0x5c/0x80
[  +0.000009]  invoke_syscall+0x74/0x260
[  +0.000009]  el0_svc_common.constprop.0+0xcc/0x260
[  +0.000009]  do_el0_svc+0x50/0x70
[  +0.000007]  el0_svc+0x68/0x1a0
[  +0.000012]  el0t_64_sync_handler+0x11c/0x150
[  +0.000008]  el0t_64_sync+0x18c/0x190

[  +0.000018] Allocated by task 0:
[  +0.000007] (stack is not available)

[  +0.000011] Freed by task 2695:
[  +0.000008]  kasan_save_stack+0x2c/0x5c
[  +0.000011]  kasan_set_track+0x2c/0x40
[  +0.000008]  kasan_set_free_info+0x28/0x50
[  +0.000009]  ____kasan_slab_free+0x128/0x1d4
[  +0.000008]  __kasan_slab_free+0x18/0x24
[  +0.000007]  slab_free_freelist_hook+0x108/0x230
[  +0.000011]  kfree+0x110/0x35c
[  +0.000008]  release_nodes+0xf0/0x16c
[  +0.000009]  devres_release_group+0x180/0x270
[  +0.000008]  component_unbind+0x128/0x1e0
[  +0.000010]  component_unbind_all+0x1b8/0x264
[  +0.000009]  meson_drv_unbind+0x1a0/0x2ac [meson_drm]
[  +0.000025]  take_down_aggregate_device+0xb0/0x160
[  +0.000009]  component_del+0x18c/0x360
[  +0.000009]  meson_dw_hdmi_remove+0x28/0x40 [meson_dw_hdmi]
[  +0.000012]  platform_remove+0x64/0xb0
[  +0.000008]  device_remove+0xb8/0x154
[  +0.000009]  device_release_driver_internal+0x398/0x5b0
[  +0.000009]  driver_detach+0xac/0x1b0
[  +0.000009]  bus_remove_driver+0x158/0x29c
[  +0.000008]  driver_unregister+0x70/0xb0
[  +0.000008]  platform_driver_unregister+0x20/0x2c
[  +0.000008]  meson_dw_hdmi_platform_driver_exit+0x1c/0x30 [meson_dw_hdmi]
[  +0.000011]  __do_sys_delete_module+0x288/0x400
[  +0.000010]  __arm64_sys_delete_module+0x5c/0x80
[  +0.000008]  invoke_syscall+0x74/0x260
[  +0.000008]  el0_svc_common.constprop.0+0xcc/0x260
[  +0.000008]  do_el0_svc+0x50/0x70
[  +0.000007]  el0_svc+0x68/0x1a0
[  +0.000009]  el0t_64_sync_handler+0x11c/0x150
[  +0.000009]  el0t_64_sync+0x18c/0x190

[  +0.000014] The buggy address belongs to the object at ffff000020c39000
               which belongs to the cache kmalloc-4k of size 4096
[  +0.000008] The buggy address is located 1504 bytes inside of
               4096-byte region [ffff000020c39000, ffff000020c3a000)

[  +0.000016] The buggy address belongs to the physical page:
[  +0.000009] page:fffffc0000830e00 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x20c38
[  +0.000013] head:fffffc0000830e00 order:3 compound_mapcount:0 compound_pincount:0
[  +0.000008] flags: 0xffff00000010200(slab|head|node=0|zone=0|lastcpupid=0xffff)
[  +0.000019] raw: 0ffff00000010200 fffffc0000fd4808 fffffc0000126208 ffff000000002e80
[  +0.000009] raw: 0000000000000000 0000000000020002 00000001ffffffff 0000000000000000
[  +0.000008] page dumped because: kasan: bad access detected

[  +0.000011] Memory state around the buggy address:
[  +0.000008]  ffff000020c39480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007]  ffff000020c39500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007] >ffff000020c39580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007]                                                        ^
[  +0.000007]  ffff000020c39600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000007]  ffff000020c39680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  +0.000006] ==================================================================

The reason this is happening is unloading meson-dw-hdmi will cause the
component API to take down the aggregate device, which in turn will cause
all devres-managed memory to be freed, including the struct dw_hdmi
allocated in dw_hdmi_probe. This struct embeds a struct drm_bridge that is
added at the end of the function, and which is later on picked up in
meson_encoder_hdmi_init.

However, when attaching the bridge to the encoder created in
meson_encoder_hdmi_init, it's linked to the encoder's bridge chain, from
where it never leaves, even after devres_release_group is called when the
driver's components are unbound and the embedding structure freed.

Then, when calling drm_dev_put in the aggregate driver's unbind function,
drm_bridge_detach is called for every single bridge linked to the encoder,
including the one whose memory had already been deallocated.

Fix by calling component_unbind_all after drm_dev_put.

Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220919010940.419893-2-adrian.larumbe@collabora.com

drm/bridge: lt8912b: clarify lvds output status

Add comments on the lt8912_write_lvds_config() config to document the
current settings and to make it clear that this is a hardcoded
configuration not relevant for the HDMI output (could be removed without
affecting the HDMI port).

No changes on the actual register writes.

Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922124306.34729-5-dev@pschenker.ch

drm/amdgpu: Fix VRAM eviction issue

A user reported that when he starts a game (MTGA) with wine,
he observed an error msg failed to pin framebuffer with error -12.
Found an issue with the VRAM mem type eviction decision condition
logic. This patch will fix the if condition code error.

Gitlab bug link:
https://gitlab.freedesktop.org/drm/amd/-/issues/2159

Fixes: ded910f368a5 ("drm/amdgpu: Implement intersect/compatible functions")
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922151447.265696-1-Arunpravin.PaneerSelvam@amd.com
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/vmwgfx: Fix memory leak in vmw_mksstat_add_ioctl()

If the copy of the description string from userspace fails, then the page
for the instance descriptor doesn't get freed before returning -EFAULT,
which leads to a memleak.

Fixes: 7a7a933edd6c ("drm/vmwgfx: Introduce VMware mks-guest-stats")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916204751.720716-1-rafaelmendsr@gmail.com

drm: bridge/dw-hdmi-ahb-audio: use strscpy() is more robust and safer

The implementation of strscpy() is more robust and safer.

That's now the recommended way to copy NUL terminated strings.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220919030401.211331-1-chi.minghao@zte.com.cn

drm/ast: Fix video broken in some resolutions on ast2600

Some cases are not handled well for ast2600.

Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916091706.4559-1-jammy_huang@aspeedtech.com

drm/ast: Add resolution support for 1152x864@75

Add 1152x864 into support list.

Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916085058.3386-1-jammy_huang@aspeedtech.com

drm/plane-helper: Provide DRM_PLANE_NON_ATOMIC_FUNCS initializer macro

Provide DRM_PLANE_NON_ATOMIC_FUNCS, which initializes plane functions
of non-atomic drivers to default values. The macro is not supposed to
be used in new code, but helps with documenting and finding existing
users.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Lyude Paul <lyude@redhat.com> # nouveau
Link: https://patchwork.freedesktop.org/patch/msgid/20220909105947.6487-5-tzimmermann@suse.de

drm/plane-helper: Warn if atomic drivers call non-atomic helpers

The plane update and disable helpers are only useful for non-atomic
drivers. Print a warning if an atomic driver calls them.

Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909105947.6487-4-tzimmermann@suse.de

drm/plane: Allocate planes with drm_universal_plane_alloc()

Provide drm_univeral_plane_alloc() to allocate and initialize a
plane. Code for non-atomic drivers uses this pattern. Convert them to
the new function. The modeset helpers contain a quirk for handling their
color formats differently. Set the flag outside plane allocation.

The new function is already deprecated to some extend. Drivers should
rather use drmm_univeral_plane_alloc() or drm_universal_plane_init().

v2:
* kerneldoc fixes (Javier)
* grammar fixes in commit message

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com> # nouveau
Link: https://patchwork.freedesktop.org/patch/msgid/20220909105947.6487-3-tzimmermann@suse.de

drm/plane: Remove drm_plane_init()

Open-code drm_plane_init() and remove the function from DRM. The
implementation of drm_plane_init() is a simple wrapper around a call
to drm_universal_plane_init(), so drivers can just use that instead.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Lyude Paul <lyude@redhat.com> # nouveau
Acked-by: Jyri Sarha <jyri.sarha@iki.fi>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909105947.6487-2-tzimmermann@suse.de

drm/atomic-helper: Fix kernel-doc

drivers/gpu/drm/drm_atomic_helper.c:802: warning: expecting prototype for drm_atomic_helper_check_wb_connector_state(). Prototype was for drm_atomic_helper_check_wb_encoder_state() instead.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2216
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220919103058.25561-1-jiapeng.chong@linux.alibaba.com

dma-buf: fix dma_fence_default_wait() signaling check

That check must now come after grabing the spinlock, not before.

Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: b96fb1e724ae ("dma-buf: dma_fence_wait must enable signaling")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220919120618.113332-1-christian.koenig@amd.com

Revert "drm/bridge: chrontel-ch7033: Add byteswap order setting"

Revert this patch since it depends on devicetree functionality that
previously has been reverted in the below commit.

commit e798ba3374a1 ("Revert "dt-bindings: Add byteswap order to chrontel ch7033"")

This reverts commit ce9564cfc9aea65e68eb343c599317633bc2321a.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220919102009.150503-3-robert.foss@linaro.org

Revert "Revert "drm/bridge: ti-sn65dsi86: Implement bridge connector operations for DP""

This commit was accidentally reverted instead of another commit, and
therefore needs to be reinstated.

This reverts commit 8c9c40ec83445b188fb6b59e119bf5c2de81b02d.

Fixes: 8c9c40ec8344 ("Revert "drm/bridge: ti-sn65dsi86: Implement bridge connector operations for DP"")
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220919102009.150503-2-robert.foss@linaro.org

drm/mediatek: dp: change mtk_dp_driver to static

mtk_dp_driver is only used in mtk_dp.c now, change it
to static.

Fixes: f70ac097a2cf ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913134929.1970187-1-yangyingliang@huawei.com

drm/mediatek: dp: Fix compiler warning in mtk_dp_video_mute()

Fix debug message formatting by using %s instead of 0x%x.

Fixes: f70ac097a2cf ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Reported-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916133821.27980-4-rex-bc.chen@mediatek.com

drm/mediatek: dp: Remove unused register definitions

Some definitions in mtk_dp_reg.h are not used, so remove these
redundant codes.

Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916133821.27980-3-rex-bc.chen@mediatek.com

drm/mediatek: dp: Reduce indentation in mtk_dp_bdg_detect()

In order to improve human readability, reduce the indentation by
returning early if the dp/edp cable is not plugged in.

Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916133821.27980-2-rex-bc.chen@mediatek.com

drm/gma500: Call acpi_video_register_backlight()

On machines without an Intel video opregion the acpi_video driver
immediately probes the ACPI video bus and used to also immediately
register acpi_video# backlight devices when supported.

Once the drm/kms driver then loaded later and possibly registered
a native backlight device then the drivers/acpi/video_detect.c code
unregistered the acpi_video0 device to avoid there being 2 backlight
devices (when acpi_video_get_backlight_type()==native).

This means that userspace used to briefly see 2 devices and the
disappearing of acpi_video0 after a brief time confuses the systemd
backlight level save/restore code, see e.g.:
https://bbs.archlinux.org/viewtopic.php?id=269920

To fix this the ACPI video code has been modified to make backlight class
device registration a separate step, relying on the drm/kms driver to
ask for the acpi_video backlight registration after it is done setting up
its native backlight device.

Add a call to the new acpi_video_register_backlight() function after
setting up the gma500's native backlight, so that the acpi_video backlight
device gets registered on systems where the gma500's native backlight
device is not registered.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220917205920.647212-6-hdegoede@redhat.com

drm/gma500: Don't register backlight when another backlight should be used

Before this commit when we want userspace to use the acpi_video backlight
device we register both the GPU's native backlight device and acpi_video's
firmware acpi_video# backlight device. This relies on userspace preferring
firmware type backlight devices over native ones.

Registering 2 backlight devices for a single display really is
undesirable, don't register the GPU's native backlight device when
another backlight device should be used.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220917205920.647212-5-hdegoede@redhat.com

drm/gma500: Use backlight_get_brightness() to get the brightness

Use backlight_get_brightness() instead of directly referencing
bd->props.brightness. This will take backlight_is_blank() into account,
properly setting brightness to 0 when screen-blanking has been requested
through the backlight sysfs interface.

Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220917205920.647212-4-hdegoede@redhat.com

drm/gma500: Change registered backlight device type to raw/native

Change the type for the registered backlight class device from platform
to raw/native.

The poulsbo/cedarview/oaktrail backlight support is using native GPU
backlight control and as such the type should be raw (aka native) as
is done by all the other native GPU backlight driver code.

Note this will not change much from userspace's point of view.
poulsbo/cedarview laptops typically offer both an ACPI-video
backlight interface as well as the native GPU backlight interface.

The /sys/class/backlight/acpi_video0 has a type of firmware and
userspace typically looks for firmware devices before looking
for platform devices. The typical standard lookup order is:
firmware -> platform -> raw

This means that both before and after this change typical userspace
backlight consumers (sich as e.g. GNOME) will prefer the firmware
acpi_video0 backlight device.

This has been tested on a Packard Bell Dot SC (Intel Atom N2600, cedarview)
and a Sony Vaio vpc-x11s1e (Intel N540, poulsbo) laptop.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220917205920.647212-3-hdegoede@redhat.com

drm/gma500: Refactor backlight support (v2)

Refactor backlight support so that the gma_backlight_enable() /
gma_backlight_disable() / gma_backlight_set() functions used by
the Opregion handle will also work if no backlight_device gets
registered.

This is a preparation patch for not registering the gma500's own backlight
device when acpi_video should be used, since registering 2 backlight
devices for a single display really is undesirable.

Since the acpi-video interface often uses the OpRegion we need to keep
the OpRegion functional even when dev_priv->backlight_device is NULL.

As a result of this refactor the actual backlight_device_register()
call is moved to the shared backlight.c code and all #ifdefs related to
CONFIG_BACKLIGHT_CLASS_DEVICE are now also limited to backlight.c .

No functional changes intended.

This has been tested on a Packard Bell Dot SC (Intel Atom N2600, cedarview)
and a Sony Vaio vpc-x11s1e (Intel N540, poulsbo) laptop.

Changes in v2:
- Fix unused variable warnings when CONFIG_BACKLIGHT is not selected by
  marking the 2 variables as  __maybe_unused.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220917205920.647212-2-hdegoede@redhat.com

drm: panel-orientation-quirks: Add quirk for Aya Neo Air

Yet another x86 gaming handheld.

This one has many SKUs with quite a few of DMI strings,
so let's just use a catchall, just as with Aya Neo Next.

Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220825191946.1678798-1-maccraft123mc@gmail.com

drm/gma500: Remove unnecessary suspend/resume wrappers

The psb_runtime_suspend/resume/thaw/freeze/restore functions are all
just 1:1 wrappers around gma_power_suspend/_resume.

Drop these wrappers and use the DEFINE_RUNTIME_DEV_PM_OPS() macro to
define the dev_pm_ops struct.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909115646.99920-7-hdegoede@redhat.com

drm/gma500: Rewrite power management code

Rewrite the power.c code. For some reason this was doing locking +
refcounting + state (suspended or not) bookkeeping all by itself.

But there is no reason for this, this is all taken care of by
the runtime-pm core, through pm_runtime_get()/_put().

Besides this not being necessary the DIY code is also quite weird/
buggy in some places. E.g. power_begin() would manually do a resume
when not resumed already and force_on=true, followed by a
pm_runtime_get(), which will cause a call to gma_power_resume() to
get scheduled which would redo the entire resume again. Which can
all be replaced by a single pm_runtime_get_sync() call.

Note that this is just a cleanup, this does not actually fix
the (disabled through #if 0) runtime-pm support. It does now call
pm_runtime_enable(), but only after doing a pm_runtime_get() at
probe-time, so the device is never runtime suspended.

Doing this permanent get() + enable() instead of not calling
enable() at all is necessary for the pm_runtime_get_if_in_use() call
in gma_power_begin() to work properly.

Note this also removes the gma_power_is_on() call a check like this
without actually holding a reference is always racy, so it is a bad
idea (and therefor has no pm_runtime_foo() equivalent).

The 2 code paths which were using gma_power_is_on() are actually both
guaranteed to only run when the device is powered-on so the 2 checks
can simply be dropped.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909115646.99920-6-hdegoede@redhat.com

drm/gma500: Remove a couple of not useful function wrappers

The gma_crtc_set_config() and psb_unlocked_ioctl() functions are 1:1
wrappers for drm_helpers. Drop these wrappers.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909115646.99920-5-hdegoede@redhat.com

drm/gma500: Remove never set dev_priv->rpm_enabled flag

The rpm_enabled flag is never set, remove it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909115646.99920-4-hdegoede@redhat.com

drm/gma500: Remove runtime_allowed dead code in psb_unlocked_ioctl()

runtime_allowed is initialized to 0, so the runtime_allowed == 1 condition
is never true making this dead code. Remove it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909115646.99920-3-hdegoede@redhat.com

drm/gma500: Fix (vblank) IRQs not working after suspend/resume

Fix gnome-shell (and other page-flip users) hanging after suspend/resume
because of the gma500's IRQs not working.

This fixes 2 problems with the IRQ handling:

1. gma_power_off() calls gma_irq_uninstall() which does a free_irq(), but
   gma_power_on() called gma_irq_preinstall() + gma_irq_postinstall() which
   do not call request_irq. Replace the pre- + post-install calls with
   gma_irq_install() which does prep + request + post.

2. After fixing 1. IRQs still do not work on a Packard Bell Dot SC (Intel
   Atom N2600, cedarview) netbook.

   Cederview uses MSI interrupts and it seems that the BIOS re-configures
   things back to normal APIC based interrupts during S3 suspend. There is
   some MSI PCI-config registers save/restore code which tries to deal with
   this, but on the Packard Bell Dot SC this is not sufficient to restore
   MSI IRQ functionality after a suspend/resume.

   Replace the PCI-config registers save/restore with pci_disable_msi() on
   suspend + pci_enable_msi() on resume. Fixing e.g. gnome-shell hanging.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220906203852.527663-4-hdegoede@redhat.com
(cherry picked from commit 235fdbc32d559db21e580f85035c59372704f09e)

drm/vboxvideo: fix repeated words in comments

Delete the redundant word 'the'.

Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220824130226.33980-1-yuanjilin@cdjrlc.com

drm: panel-orientation-quirks: Add quirk for Anbernic Win600

This device is another x86 gaming handheld, and as (hopefully) there is
only one set of DMI IDs it's using DMI_EXACT_MATCH

Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220803182402.1217293-1-maccraft123mc@gmail.com

drm/plane-helper: Add a drm_plane_helper_atomic_check() helper

Provides a default plane state check handler for primary planes that are a
fullscreen scanout buffer and whose state scale and position can't change.

There are some drivers that duplicate this logic in their helpers, such as
simpledrm and ssd130x. Factor out this common code into a plane helper and
make drivers use it.

Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913162307.121503-1-javierm@redhat.com

drm/sched: Use parent fence instead of finished

Using the parent fence instead of the finished fence
to get the job status. This change is to avoid GPU
scheduler timeout error which can cause GPU reset.

Signed-off-by: Arvind Yadav <Arvind.Yadav@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220914164321.2156-6-Arvind.Yadav@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

dma-buf: dma_fence_wait must enable signaling

dma_fence_wait() should always enable signaling even
when the fence is already signaled.

Signed-off-by: Arvind Yadav <Arvind.Yadav@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220914164321.2156-5-Arvind.Yadav@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

dma-buf: Enable signaling on fence for selftests

Here's enabling software signaling on fence for selftest.

Signed-off-by: Arvind Yadav <Arvind.Yadav@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220914164321.2156-4-Arvind.Yadav@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

dma-buf: set signaling bit for the stub fence

Here's setting software signaling bit for the stub fence
which is always signaled. If this fence signaling bit is
not set then the AMD GPU scheduler will cause a GPU reset
due to a GPU scheduler cleanup activity timeout.

Signed-off-by: Arvind Yadav <Arvind.Yadav@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220914164321.2156-3-Arvind.Yadav@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

dma-buf: Remove the signaled bit status check

Remove the signaled bit status check because it is returning
early when the fence is already signaled and
__dma_fence_enable_signaling is checking the status of signaled
bit again.

Signed-off-by: Arvind Yadav <Arvind.Yadav@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220914164321.2156-2-Arvind.Yadav@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/rockchip: remove vop_writel from vop1 driver

cppcheck reports
[drivers/gpu/drm/rockchip/rockchip_drm_vop.c:186]: (style) The function 'vop_writel' is never used.

vop_writel is static function that is not used, so remove it.

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220521190716.1936193-1-trix@redhat.com

drm/rockchip: support gamma control on RK3399

The RK3399 has a 1024-entry gamma LUT with 10 bits per component on its
"big" VOP and a 256-entry, 8 bit per component LUT on the "little" VOP.
Compared to the RK3288, it no longer requires disabling gamma while
updating the LUT. On the RK3399, the LUT can be updated at any time as
the hardware has two LUT buffers, one can be written while the other is
in use. A swap of the buffers is triggered by writing 1 to the
update_gamma_lut register.

Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Tested-by: "Milan P. Stanić" <mps@arvanta.net>
Tested-by: Linus Heckemann <git@sphalerite.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211019215843.42718-3-sigmaris@gmail.com

drm/rockchip: define gamma registers for RK3399

The VOP on RK3399 has a different approach from previous versions for
setting a gamma lookup table, using an update_gamma_lut register. As
this differs from RK3288, give RK3399 its own set of "common" register
definitions.

Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Tested-by: "Milan P. Stanić" <mps@arvanta.net>
Tested-by: Linus Heckemann <git@sphalerite.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211019215843.42718-2-sigmaris@gmail.com

drm/tests: Change "igt_" prefix to "drm_test_"

With the introduction of KUnit, IGT is no longer the only option to run
the DRM unit tests, as the tests can be run through kunit-tool or on
real hardware with CONFIG_KUNIT.

Therefore, remove the "igt_" prefix from the tests and replace it with
the "drm_test_" prefix, making the tests' names independent from the tool
used.

Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Acked-by: David Gow <davidgow@google.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220911191756.203118-2-mairacanal@riseup.net

drm/tests: Split drm_framebuffer_create_test into parameterized tests

The igt_check_drm_framebuffer_create is based on a loop that executes
tests for all createbuffer_tests test cases. This could be better
represented by parameterized tests, provided by KUnit.

So, convert the igt_check_drm_framebuffer_create into parameterized tests.

Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: David Gow <davidgow@google.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220911191756.203118-1-mairacanal@riseup.net

Merge tag 'backlight-detect-refactor-1' of git://git./linux/kernel/git/pdx86/platform-drivers-x86 into drm-misc-next

Immutable backlight-detect-refactor branch between acpi, drm-* and pdx86

Tag (immutable branch) with v6.0-rc1 + the (acpi/x86) backlight
detect refactor work. For merging into the acpi, drm-* and pdx86
subsystems.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmMVsogUHGhkZWdvZWRl
# QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9yy6wgAlig+7hkq940L62lTpj0g2gNQv8zc
# HCsMpnU7dnJcZYaEvIjouZhf33ZbN52c0fQq2JWjt7fFX04LLyIiyrJ26Lc293JR
# ++yXpJcVoewRGqApy/P3Z05TKUCLll5bexvK4t8isnhOtEXD/nDPWKTLIV2Kd1DK
# nLY4KgRznXZ85RhYheUEdidZ7Lwlzt1JVBMq7tpnzu3nVdDExyZmqlqCUITcLynu
# ysuASQGr0D2i+1vb9eifHIA3xsQO0S37Bv62aBMBKxB6B8Fz1DYr8VA2YvoT82Hv
# IFT0hzCCZ/63Ljga05O78TwraxAQX0RvZWqjqGgnZg6fIBh2hxUiqeQY6g==
# =SA1R
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 05 Sep 2022 09:25:44 AM IST
# gpg:                using RSA key BAF03B5D2718411A5E9E177E92EC4779440327DC
# gpg:                issuer "hdegoede@redhat.com"
# gpg: Can't check signature: No public key
From: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/261afe3d-7790-e945-adf6-a2c96c9b1eff@redhat.com

Merge drm/drm-next into drm-misc-next

We need 6.0-rc1 to merge the backlight rework PR.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

drm/amd/pm: remove unused declarations in hardwaremanager.h

phm_is_hw_access_blocked() and phm_block_hw_access() has been
removed since commit 698f88e697cc ("drm/amd/powerplay: delete
dead code in powerplay"), so remove them.

Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913024847.552254-6-cuigaosheng1@huawei.com

drm/gma500: remove unused declarations in psb_intel_drv.h

psb_intel_sdvo_supports_hotplug(), psb_intel_sdvo_set_hotplug()
and psb_intel_sdvo_find() have been removed since
commit 871c60156dbe ("drm/gma500: Remove dead code"),
so remove them.

Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913024847.552254-5-cuigaosheng1@huawei.com

drm/radeon: remove unused declarations for radeon

radeon_combios_get_ext_tmds_info() has been removed since
commit fcec570b27a4 ("drm/radeon/kms: add support for
external tmds on legacy boards").

radeon_mst has been removed since
commit 01ad1d9c2888 ("drm/radeon: Drop legacy MST support").

r600_hdmi_acr() has been removed since
commit 64424d6e45ae ("radeon/audio: consolidate update_acr()
functions (v2)").

So remove the declarations for them from header file.

Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913024847.552254-4-cuigaosheng1@huawei.com

drm/radeon/r600_cs: remove r600_cs_legacy_get_tiling_conf() declaration

r600_cs_legacy_get_tiling_conf() has been removed since
commit 8333f607a631 ("drm/radeon: remove UMS support"),
so remove it.

Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913024847.552254-3-cuigaosheng1@huawei.com

drm/vmwgfx: remove unused vmw_bo_is_vmw_bo() declaration

vmw_bo_is_vmw_bo() has been removed since
commit 298799a28264 ("drm/vmwgfx: Fix gem refcounting and
memory evictions"), so remove it.

Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913024847.552254-2-cuigaosheng1@huawei.com

drm/scdc: Document hotplug gotchas

There's some interactions between the SCDC setup and the disconnection /
reconnection of displays. Let's document it and a solution.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-9-maxime@cerno.tech

drm/vc4: hdmi: Reset link on hotplug

During a hotplug cycle (such as a TV going out of suspend, or when the
cable is disconnected and reconnected), the expectation is that the same
state used before the disconnection is reused until the next commit.

However, the HDMI scrambling requires that some flags are set in the
monitor, and those flags are very likely to be reset when the cable has
been disconnected. This will thus result in a blank display, even if the
display pipeline configuration hasn't been modified or is in the exact
same state.

The solution we've had so far is to enable the scrambling-related bits
again on reconnection, but the HDMI 2.0 specification (Section 6.1.3.1 -
Scrambling Control) requires that the scrambling enable bit is set
before sending any scrambled video signal. Using that solution thus
breaks that expectation.

The solution used by i915 is to do a full modeset on the connector so
that we disable the video signal, enable the scrambling bit, and enable
the video signal again.

As such, we took that code and plugged it into vc4. It probably could
have been turned into an helper, but it proved to be difficult for
several reasons:

  * i915 has fairly different structures than simpler KMS drivers such
    as vc4, so doing some code that works with both proved to be
    difficult;

  * Other simpler drivers could reuse some of it (tegra, dw-hdmi), but
    it would still require to move some parameters currently stored in
    private structure that are needed to compute whether the scrambling
    is needed or not, and then inform the driver that it needs to be
    enabled. Some of those parameters are already in core structures
    (drm_display_mode, drm_display_info, bpc), but the output format
    isnt't. Adding it is fairly challenging since unlike the TMDS char
    rate or mode, there's no consensus on what format to pick in
    drivers, so it's not possible to write some generic code that can
    depend on it.

For these reasons, we chose to duplicate the code for now, until someone
else really needs it as well, in which case we will be able to convert
it into a generic helper.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-8-maxime@cerno.tech

drm/vc4: hdmi: Move vc4_hdmi_supports_scrambling() around

We'll need it earlier in the driver, so let's move it next to the other
scrambling-related helpers.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-7-maxime@cerno.tech

drm/vc4: hdmi: Switch to detect_ctx

We'll need the locking context in future patch, so let's convert .detect
to .detect_ctx.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-6-maxime@cerno.tech