OSDN Git Service
Carl Huang [Thu, 19 Apr 2018 16:39:40 +0000 (19:39 +0300)]
ath10k: support MAC address randomization in scan
The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.
Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Carl Huang [Thu, 19 Apr 2018 16:39:38 +0000 (19:39 +0300)]
ath10k: add WMI_SERVICE_AVAILABLE_EVENT support
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Mack [Tue, 10 Apr 2018 17:35:58 +0000 (19:35 +0200)]
wcn36xx: use READ_ONCE() to access desc->ctrl
When accessing shared memory to check for the stat of submitted
descriptors, make sure to use READ_ONCE(). This will guarantee the
compiler treats these memory locations as volatile and doesn't apply
any caching.
While this doesn't fix any particular problem I ran into, it's best
practice to do it this way.
Note that this patch also removes the superflous extra condition check
in the do-while loop in reap_tx_dxes(), as the loop will break
instantly anyway in that case.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Mon, 16 Apr 2018 04:26:45 +0000 (09:56 +0530)]
ath10k: fix fw path name for WCN3990 target
FW path is mapped incorrectly for the WCN3990
hw version. Fix fw path with correct hw1.0 name.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Sun, 15 Apr 2018 12:22:28 +0000 (14:22 +0200)]
ath10k: add inlined wrappers for htt rx ops
Added for the same reason as the TX wrappers.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Erik Stromdahl [Sun, 15 Apr 2018 12:22:27 +0000 (14:22 +0200)]
ath10k: add inlined wrappers for htt tx ops
These wrappers makes the HTT ops align better with the HIF ops
(where similar wrappers are used).
It also makes it easier for a target to have unsupported ops
(by letting the corresponding function pointer be NULL).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Thomas Hebb [Fri, 13 Apr 2018 14:40:26 +0000 (17:40 +0300)]
ath10k: search all IEs for variant before falling back
commit
f2593cb1b291 ("ath10k: Search SMBIOS for OEM board file
extension") added a feature to ath10k that allows Board Data File
(BDF) conflicts between multiple devices that use the same device IDs
but have different calibration requirements to be resolved by allowing
a "variant" string to be stored in SMBIOS [and later device tree, added
by commit
d06f26c5c8a4 ("ath10k: search DT for qcom,ath10k-calibration-
variant")] that gets appended to the ID stored in board-2.bin.
This original patch had a regression, however. Namely that devices with
a variant present in SMBIOS that didn't need custom BDFs could no longer
find the default BDF, which has no variant appended. The patch was
reverted and re-applied with a fix for this issue in commit
1657b8f84ed9
("search SMBIOS for OEM board file extension").
But the fix to fall back to a default BDF introduced another issue: the
driver currently parses IEs in board-2.bin one by one, and for each one
it first checks to see if it matches the ID with the variant appended.
If it doesn't, it checks to see if it matches the "fallback" ID with no
variant. If a matching BDF is found at any point during this search, the
search is terminated and that BDF is used. The issue is that it's very
possible (and is currently the case for board-2.bin files present in the
ath10k-firmware repository) for the default BDF to occur in an earlier
IE than the variant-specific BDF. In this case, the current code will
happily choose the default BDF even though a better-matching BDF is
present later in the file.
This patch fixes the issue by first searching the entire file for the ID
with variant, and searching for the fallback ID only if that search
fails. It also includes some code cleanup in the area, as
ath10k_core_fetch_board_data_api_n() no longer does its own string
mangling to remove the variant from an ID, instead leaving that job to a
new flag passed to ath10k_core_create_board_name().
I've tested this patch on a QCA4019 and verified that the driver behaves
correctly for 1) both fallback and variant BDFs present, 2) only fallback
BDF present, and 3) no matching BDFs present.
Fixes:
1657b8f84ed9 ("ath10k: search SMBIOS for OEM board file extension")
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maharaja Kennadyrajan [Fri, 13 Apr 2018 07:48:12 +0000 (13:18 +0530)]
ath10k: fix a typo in ath10k_wmi_set_wmm_param()
Fix a typo in the function ath10k_wmi_set_wmm_param().
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Manikanta Pubbisetty [Thu, 12 Apr 2018 12:16:50 +0000 (17:46 +0530)]
ath10k: correct target assert problem due to CE5 stuck
Correct a minor bug in the commit
0628467f97b5 ("ath10k: fix
copy engine 5 destination ring stuck") which introduced a change to fix
firmware assert that happens when ring indices of copy engine 5 are stuck
for a specific duration, problem with this fix is that it did not use
ring arithmatic. As a result,firmware asserts did not go away entirely
athough the frequency of occurrence has reduced. Using ring arithmatic
to fix the issue.
Tested on QCA9984(fw version-10.4-3.4-00082).
Fixes:
0628467f97b5 ("ath10k: fix copy engine 5 destination ring stuck)
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Colin Ian King [Thu, 29 Mar 2018 16:53:04 +0000 (17:53 +0100)]
ath6kl: fix spelling mistake: "chache" -> "cache"
Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:35 +0000 (18:01 +0300)]
dt: bindings: add bindings for wcn3990 wifi block
Add device tree binding documentation details for wcn3990
wifi block present in Qualcomm SDM845/APQ8098 SoC into
"qcom,ath10k.txt".
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:34 +0000 (18:01 +0300)]
ath10k: vote for hardware resources for WCN3990
Add clock and regulator votes for WCN3990 WLAN
chipset.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Tue, 10 Apr 2018 15:01:32 +0000 (18:01 +0300)]
ath10k: check all CE for data if irq summary is not retained
WCN3990 has interrupts per CE and the interrupt summary
is not retained after the interrupt handler has finished
execution. We need to check if we received any
ce in rx and tx completion path.
Generate a interrupt summary with all CE interrupts if
the target does not retain interrupt summary after the
execution of interrupt handler.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Tue, 10 Apr 2018 15:01:29 +0000 (18:01 +0300)]
ath10k: add support to get target info from hif ops
wcn3990 does not use bmi.
Add support to get target info from hif ops.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:27 +0000 (18:01 +0300)]
ath10k: modify hif tx paddr to dma_addr_t type
Change type of hif sg tx paddr to dma_addr_t for
supporting target having addressing mode greater than
32 bit.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:25 +0000 (18:01 +0300)]
ath10k: add hif rx methods for wcn3990
Add hif rx methods in rx path for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:24 +0000 (18:01 +0300)]
ath10k: add hif tx methods for wcn3990
Add hif tx/tx-complete methods for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:22 +0000 (18:01 +0300)]
ath10k: add hif power-up/power-down methods
Add hif power-up/power-down methods for wcn3990
target.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:20 +0000 (18:01 +0300)]
ath10k: map HTC services to tx/rx pipes for wcn3990
Add mapping of HTC endpoint services supported
by wcn3990 target to tx/rx pipe.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:18 +0000 (18:01 +0300)]
ath10k: add HTC services for WCN3990
WCN3990 target uses 3 Copy engine(CE1/CE9/CE10) in RX path
and CE 11 for pktlog.
Add data path HTC ep services and PKTLOG services for WCN3990.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:17 +0000 (18:01 +0300)]
ath10k: add hif start/stop methods for wcn3990 snoc layer
Add hif start/stop callback for allocating/freeing buffers
on tx/rx pipe and enabling/disabling the tx/rx pipe
interrupts.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:15 +0000 (18:01 +0300)]
ath10k: add resource init and deinit for WCN3990
Add methods for resource(memory, irq, HOST CE config)
initialization and de-initialization for WCN3990 target.
WCN3990 target uses 12 copy engine and following CE config.
[CE0] :host->target control and raw streams
[CE1] :target->host HTT
[CE2] :target->host WMI
[CE3] :host->target WMI
[CE4] :host->target HTT
[CE5] :reserved
[CE6] :Target autonomous HIF_memcpy
[CE7] :reserved
[CE8] :reserved
[CE9] :target->host HTT
[CE10] :target->host HTT
[CE11] :target -> host PKTLOG
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:14 +0000 (18:01 +0300)]
ath10k: platform driver for WCN3990 SNOC WLAN module
WCN3990 is integrated 802.11ac chipset with SNOC
bus interface. Add snoc layer driver registration
and associated ops.
WCN3990 support is not yet complete as cold-boot
handshake is done using qmi(Qualcomm-MSM-Interface)
and qmi client support will be added once qmi framework
is available.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Tue, 10 Apr 2018 15:01:11 +0000 (18:01 +0300)]
ath10k: build ce layer in ath10k core module
CE layer is shared between pci and snoc target and results
in duplicate object inclusion if both modules are compiled
together statically and undefined KBUILD_MODNAME if
compiled as module.
Fix this by building ce layer in ath10k core module by
adding ce object inclusion with ATH10K_CE boolean CONFIG.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Venkateswara Naralasetty [Tue, 10 Apr 2018 15:01:05 +0000 (18:01 +0300)]
ath10k: Add tx ack signal support for management frames
This patch add support to get RSSI from acknowledgment
frames for transmitted management frames.
hardware_used: QCA4019, QCA9984.
firmware version: 10.4-3.5.3-00052.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Mack [Tue, 10 Apr 2018 14:52:45 +0000 (17:52 +0300)]
wcn36xx: allocate skbs with GFP_KERNEL during init
GFP_ATOMIC should only be used when the allocation is done from atomic
context. Introduce a new flag to wcn36xx_dxe_fill_skb() and use GFP_KERNEL
when pre-allocating buffers during init.
This doesn't fix an issue that was observed in the wild, but it reduces
the chance of failed allocations under memory pressure.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Loic Poulain [Fri, 6 Apr 2018 10:11:28 +0000 (12:11 +0200)]
wcn36xx: Remove useless skb spinlock
Each DXE control block is associated to a specific channel.
The channel lock is always taken before accessing a control block.
There is no need to have an extra (useless) spinlock for the control
block skb.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Loic Poulain [Thu, 5 Apr 2018 11:51:49 +0000 (13:51 +0200)]
wcn36xx: Add missing fall through comment in smd.c
This prevents GCC warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Mack [Tue, 3 Apr 2018 16:51:54 +0000 (18:51 +0200)]
wcn36xx: don't delete invalid bss indices
The firmware code cannot cope with requests to remove BSS indices that have
not previously been added. This primarily happens when the device is
suspended and then resumed. ieee80211_reconfig() then calls into
wcn36xx_bss_info_changed() with an empty bssid and BSS_CHANGED_BSSID set,
which subsequently leads to a firmware crash:
[ 43.647928] qcom-wcnss-pil
a204000.wcnss: fatal error received: halMsg.c:4964:halMsg_DelBss: Invalid BSSIndex 0
[ 43.647959] remoteproc remoteproc0: crash detected in
a204000.wcnss: type fatal error
To fix this, set bss_index to WCN36XX_HAL_BSS_INVALID_IDX for all bss
that have not been configured in the firmware, and don't call into the
firmware with invalid indices.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Mack [Tue, 3 Apr 2018 16:51:53 +0000 (18:51 +0200)]
wcn36xx: don't keep reference to skb if transmission failed
When wcn36xx_dxe_tx_frame() fails to transmit the TX frame, the driver
will call into ieee80211_free_txskb() for the skb in flight, so it'll no
longer be valid. Hence, we shouldn't keep a reference to it in ctl->skb.
Also, if the skb has IEEE80211_TX_CTL_REQ_TX_STATUS set, a pointer to
it will currently remain in wcn->tx_ack_skb, which will potentially lead
to a crash if accessed later.
Fix this by checking the return value of wcn36xx_dxe_tx_frame(), and
nullify wcn->tx_ack_skb again in case of errors. Move the assignment
of ctl->skb in wcn36xx_dxe_tx_frame() so it only happens when the
transmission is successful.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Mack [Tue, 3 Apr 2018 16:51:52 +0000 (18:51 +0200)]
wcn36xx: check for DMA mapping errors in wcn36xx_dxe_tx_frame()
Bail out if the mapping fails. Even though this hasn't occured during
tests, this unlikely case should still be handled.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Gustavo A. R. Silva [Fri, 30 Mar 2018 18:34:01 +0000 (13:34 -0500)]
ath9k: dfs: remove accidental use of stack VLA
In preparation to enabling -Wvla, remove accidental use of stack VLA.
This avoids an accidental stack VLA (since the compiler thinks
the value of FFT_NUM_SAMPLES can change, even when marked
"const"). This just replaces it with a #define.
Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Colin Ian King [Thu, 29 Mar 2018 16:59:49 +0000 (17:59 +0100)]
ath10k: fix spelling mistake: "tiggers" -> "triggers"
Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marcus Folkesson [Tue, 27 Mar 2018 20:31:44 +0000 (22:31 +0200)]
ath10k: sdio: fix memory leak for probe allocations
These allocations are not freed upon release.
When on it; go for managed resources instead.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
[kvalo: fix two checkpatch warnings]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Colin Ian King [Wed, 28 Mar 2018 17:40:27 +0000 (18:40 +0100)]
wil6210: fix potential null dereference of ndev before null check
The pointer ndev is being dereferenced before it is being null checked,
hence there is a potential null pointer deference. Fix this by only
dereferencing ndev after it has been null checked
Detected by CoverityScan, CID#
1467010 ("Dereference before null check")
Fixes:
e00243fab84b ("wil6210: infrastructure for multiple virtual interfaces")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arnd Bergmann [Wed, 28 Mar 2018 22:06:10 +0000 (00:06 +0200)]
ath10k: avoid possible string overflow
The way that 'strncat' is used here raised a warning in gcc-8:
drivers/net/wireless/ath/ath10k/wmi.c: In function 'ath10k_wmi_tpc_stats_final_disp_tables':
drivers/net/wireless/ath/ath10k/wmi.c:4649:4: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
Effectively, this is simply a strcat() but the use of strncat() suggests
some form of overflow check. Regardless of whether this might actually
overflow, using strlcat() instead of strncat() avoids the warning and
makes the code more robust.
Fixes:
bc64d05220f3 ("ath10k: debugfs support to get final TPC stats for 10.4 variants")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Joe Perches [Wed, 21 Mar 2018 10:32:52 +0000 (03:32 -0700)]
ath: Remove unnecessary ath_bcast_mac and use eth_broadcast_addr
Remove the static array and use the generic routine to set the
Ethernet broadcast address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rajkumar Manoharan [Wed, 28 Mar 2018 09:40:24 +0000 (12:40 +0300)]
ath10k: fix vdev stats for 10.4 firmware
Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Christian Lamparter [Wed, 28 Mar 2018 09:19:55 +0000 (12:19 +0300)]
ath10k: fix recent bandwidth conversion bug
The commit "cfg80211: make RATE_INFO_BW_20 the default" changed
the index of RATE_INFO_BW_20, but the updates to ath10k missed
the special bandwidth calculation case in
ath10k_update_per_peer_tx_stats().
This will fix below warning,
WARNING: CPU: 0 PID: 609 at net/wireless/util.c:1254
cfg80211_calculate_bitrate+0x174/0x220
invalid rate bw=1, mcs=9, nss=2
(unwind_backtrace) from
(cfg80211_calculate_bitrate+0x174/0x220)
(cfg80211_calculate_bitrate) from
(nl80211_put_sta_rate+0x44/0x1dc)from
(nl80211_put_sta_rate) from
(nl80211_send_station+0x388/0xaf0)
(nl80211_get_station+0xa8/0xec)
[ end trace
da8257d6a850e91a ]
Fixes:
842be75c77cb ("cfg80211: make RATE_INFO_BW_20 the default")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Anilkumar Kolli [Wed, 28 Mar 2018 09:19:40 +0000 (12:19 +0300)]
ath10k: advertize beacon_int_min_gcd
This patch fixes regression caused by
0c317a02ca98
("cfg80211: support virtual interfaces with different beacon intervals"),
with this change cfg80211 expects the driver to advertize
'beacon_int_min_gcd' to support different beacon intervals in multivap
scenario. This support is added for, QCA988X/QCA99X0/QCA9984/QCA4019.
Verifed AP + mesh bring up on QCA9984 with beacon interval 100msec and
1000msec respectively.
Frimware: firmware-5.bin_10.4-3.5.3-00053
Fixes:
0c317a02ca98 ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yingying Tang [Wed, 28 Mar 2018 09:15:35 +0000 (12:15 +0300)]
ath10k: fix TDLS peer TX data failure issue on encryped AP
For WPA encryption, QCA6174 firmware(version: WLAN.RM.4.4) will unblock
data when M4 was sent successfully. For other encryption which didn't need
4-way handshake firmware will unblock the data when peer authorized. Since
TDLS is 3-way handshake host need send authorize cmd to firmware to unblock
data.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yingying Tang [Wed, 28 Mar 2018 09:15:23 +0000 (12:15 +0300)]
ath10k: avoid to set WEP key for TDLS peer
TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yingying Tang [Wed, 28 Mar 2018 09:13:07 +0000 (12:13 +0300)]
ath10k: enable TDLS peer inactivity detection
Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yingying Tang [Wed, 28 Mar 2018 09:12:52 +0000 (12:12 +0300)]
ath10k: enable TDLS peer buffer STA feature
Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Mack [Tue, 27 Mar 2018 08:26:58 +0000 (11:26 +0300)]
wcn36xx: dequeue all pending indicator messages
In case wcn36xx_smd_rsp_process() is called more than once before
hal_ind_work was dispatched, the messages will end up in hal_ind_queue,
but wcn36xx_ind_smd_work() will only look at the first message in that
list.
Fix this by dequeing the messages from the list in a loop, and only stop
when it's empty.
This issue was found during a review of the driver. In my tests, that
race never actually occured.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Loic Poulain [Tue, 27 Mar 2018 08:26:57 +0000 (11:26 +0300)]
wcn36xx: Fix firmware crash due to corrupted buffer address
wcn36xx_start_tx function retrieves the buffer descriptor from the
channel control queue to start filling tx buffer information. However,
nothing prevents this same buffer to be concurrently accessed in a
concurent tx call, leading to potential buffer coruption and firmware
crash (observed during iperf test). The channel control queue should
only be accessed and updated with the channel lock.
Fix this issue by using a local buffer descriptor which will be copied
in the thread-safe wcn36xx_dxe_tx_frame.
Note that buffer descriptor size is few bytes so the introduced copy
overhead is insignificant. Moreover, this allows to keep the locked
section minimal.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ramon Fried [Tue, 27 Mar 2018 08:26:55 +0000 (11:26 +0300)]
wcn36xx: turn off probe response offloading
It appears that the WCN36xx firmware doesn't actually respond to
probe requests. Until it's resolved, switch the probe response
responsibility to the 802.11 layer to allow creation of
hidden SSID AP's.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Anilkumar Kolli [Tue, 27 Mar 2018 08:26:52 +0000 (11:26 +0300)]
ath10k: add memory dump support QCA9984
QCA9984/QCA99X0/QCA4019 chipsets have 8 memory regions, dump all of them to the
firmware coredump file. Some of the regions need to be read using ioread() so
add new region types for them.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[kvalo: refactoring etc]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Tue, 27 Mar 2018 08:26:50 +0000 (11:26 +0300)]
ath10k: refactor ath10k_pci_dump_memory() in preparation for QCA9984 support
As QCA9984 needs two region types refactor the code to make it easier add the
new types. No functional changes.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sathishkumar Muruganandam [Tue, 27 Mar 2018 08:26:46 +0000 (11:26 +0300)]
ath10k: suppress "Unknown eventid: 36925" warnings
FW has Smart Logging feature enabled by default for detecting failures
and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
EVENT processing yet, suppressing the unknown event ID warning by moving
this under ATH10K_DBG_WMI.
Simulated the same issue by having associated STA powered off when
ping flood was running from AP backbone. This triggerd STA KICKOUT
in AP followed by FATAL CONDITION event 36925.
Issue was reproduced and verified in below DUT
------------------------------------------------
AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ryan Hsu [Tue, 27 Mar 2018 08:25:38 +0000 (11:25 +0300)]
ath10k: add FW API 6 firmware image for QCA9377
Firmware WLAN.TF.2.1-00014-QCARMSWP-1 now supports reading the board ID
information and also required 9 IRAM bank, which older ath10k version
don't have the support will fail to be enabled, so in order to maintain
the backward compatibility, we need to update the FW API to 6.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ryan Hsu [Tue, 27 Mar 2018 08:25:36 +0000 (11:25 +0300)]
ath10k: enable QCA6174/QCA9377 to read the chip temperature
The firmware of QCA6174/QCA9377 already support the feature, just enable
it to be able to handle the get_temperature command and process the event.
You can read the temperature by using the hwmon interface,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Verified with the following hardware and software combination,
QCA6174, only firmware-4.bin doesn't support this, otherwise all support.
QCA9377, all the firmwares upstreamed support this command
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Karthikeyan Periyasamy [Tue, 27 Mar 2018 08:25:29 +0000 (11:25 +0300)]
Revert "ath10k: send (re)assoc peer command when NSS changed"
This reverts commit
55884c045d31a29cf69db8332d1064a1b61dd159.
When Ath10k is in AP mode and an unassociated STA sends a VHT action frame
(Operating Mode Notification for the NSS change) periodically to AP this causes
ath10k to call ath10k_station_assoc() which sends WMI_PEER_ASSOC_CMDID during
NSS update. Over the time (with a certain client it can happen within 15 mins
when there are over 500 of these VHT action frames) continuous calls of
WMI_PEER_ASSOC_CMDID cause firmware to assert due to resource exhaust.
To my knowledge setting WMI_PEER_NSS peer param itself enough to handle NSS
updates and no need to call ath10k_station_assoc(). So revert the original
commit from 2014 as it's unclear why the change was really needed.
Now the firmware assert doesn't happen anymore.
Issue observed in QCA9984 platform with firmware version:10.4-3.5.3-00053.
This Change tested in QCA9984 with firmware version: 10.4-3.5.3-00053 and
QCA988x platform with firmware version: 10.2.4-1.0-00036.
Firmware Assert log:
ath10k_pci 0002:01:00.0: firmware crashed! (guid
e61f1274-9acd-4c5b-bcca-
e032ea6e723c)
ath10k_pci 0002:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
ath10k_pci 0002:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 1 testmode 1
ath10k_pci 0002:01:00.0: firmware ver 10.4-3.5.3-00053 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast crc32
4c56a386
ath10k_pci 0002:01:00.0: board_file api 2 bmi_id 0:4 crc32
c2271344
ath10k_pci 0002:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
ath10k_pci 0002:01:00.0: firmware register dump:
ath10k_pci 0002:01:00.0: [00]: 0x0000000A 0x000015B3 0x00981E5F 0x00975B31
ath10k_pci 0002:01:00.0: [04]: 0x00981E5F 0x00060530 0x00000011 0x00446C60
ath10k_pci 0002:01:00.0: [08]: 0x0042F1FC 0x00458080 0x00000017 0x00000000
ath10k_pci 0002:01:00.0: [12]: 0x00000009 0x00000000 0x00973ABC 0x00973AD2
ath10k_pci 0002:01:00.0: [16]: 0x00973AB0 0x00960E62 0x009606CA 0x00000000
ath10k_pci 0002:01:00.0: [20]: 0x40981E5F 0x004066DC 0x00400000 0x00981E34
ath10k_pci 0002:01:00.0: [24]: 0x80983B48 0x0040673C 0x000000C0 0xC0981E5F
ath10k_pci 0002:01:00.0: [28]: 0x80993DEB 0x0040676C 0x00431AB8 0x0045D0C4
ath10k_pci 0002:01:00.0: [32]: 0x80993E5C 0x004067AC 0x004303C0 0x0045D0C4
ath10k_pci 0002:01:00.0: [36]: 0x80994AAB 0x004067DC 0x00000000 0x0045D0C4
ath10k_pci 0002:01:00.0: [40]: 0x809971A0 0x0040681C 0x004303C0 0x00441B00
ath10k_pci 0002:01:00.0: [44]: 0x80991904 0x0040688C 0x004303C0 0x0045D0C4
ath10k_pci 0002:01:00.0: [48]: 0x80963AD3 0x00406A7C 0x004303C0 0x009918FC
ath10k_pci 0002:01:00.0: [52]: 0x80960E80 0x00406A9C 0x0000001F 0x00400000
ath10k_pci 0002:01:00.0: [56]: 0x80960E51 0x00406ACC 0x00400000 0x00000000
ath10k_pci 0002:01:00.0: Copy Engine register dump:
ath10k_pci 0002:01:00.0: index: addr: sr_wr_idx: sr_r_idx: dst_wr_idx: dst_r_idx:
ath10k_pci 0002:01:00.0: [00]: 0x0004a000 15 15 3 3
ath10k_pci 0002:01:00.0: [01]: 0x0004a400 17 17 212 213
ath10k_pci 0002:01:00.0: [02]: 0x0004a800 21 21 20 21
ath10k_pci 0002:01:00.0: [03]: 0x0004ac00 25 25 27 25
ath10k_pci 0002:01:00.0: [04]: 0x0004b000 515 515 144 104
ath10k_pci 0002:01:00.0: [05]: 0x0004b400 28 28 155 156
ath10k_pci 0002:01:00.0: [06]: 0x0004b800 12 12 12 12
ath10k_pci 0002:01:00.0: [07]: 0x0004bc00 1 1 1 1
ath10k_pci 0002:01:00.0: [08]: 0x0004c000 0 0 127 0
ath10k_pci 0002:01:00.0: [09]: 0x0004c400 1 1 1 1
ath10k_pci 0002:01:00.0: [10]: 0x0004c800 0 0 0 0
ath10k_pci 0002:01:00.0: [11]: 0x0004cc00 0 0 0 0
ath10k_pci 0002:01:00.0: CE[1] write_index 212 sw_index 213 hw_index 0 nentries_mask 0x000001ff
ath10k_pci 0002:01:00.0: CE[2] write_index 20 sw_index 21 hw_index 0 nentries_mask 0x0000007f
ath10k_pci 0002:01:00.0: CE[5] write_index 155 sw_index 156 hw_index 0 nentries_mask 0x000001ff
ath10k_pci 0002:01:00.0: DMA addr: nbytes: meta data: byte swap: gather:
ath10k_pci 0002:01:00.0: [455]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [456]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [457]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [458]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [459]: 0x580c0a42 0 0 0 0
ath10k_pci 0002:01:00.0: [460]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [461]: 0x580c0c42 0 0 0 0
ath10k_pci 0002:01:00.0: [462]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [463]: 0x580c0c42 0 0 0 0
ath10k_pci 0002:01:00.0: [464]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [465]: 0x580c0a42 0 0 0 0
ath10k_pci 0002:01:00.0: [466]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [467]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [468]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [469]: 0x580c1c42 0 0 0 0
ath10k_pci 0002:01:00.0: [470]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [471]: 0x580c1c42 0 0 0 0
ath10k_pci 0002:01:00.0: [472]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [473]: 0x580c1c42 0 0 0 0
ath10k_pci 0002:01:00.0: [474]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [475]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [476]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [477]: 0x580c0842 0 0 0 0
ath10k_pci 0002:01:00.0: [478]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [479]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [480]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [481]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [482]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [483]: 0x580c0842 0 0 0 0
ath10k_pci 0002:01:00.0: [484]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [485]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [486]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [487]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [488]: 0x594a0038 0 0 0 1
ath10k_pci 0002:01:00.0: [489]: 0x580c0842 0 0 0 0
ath10k_pci 0002:01:00.0: [490]: 0x594a0060 0 0 0 1
ath10k_pci 0002:01:00.0: [491]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [492]: 0x58174040 0 1 0 0
ath10k_pci 0002:01:00.0: [493]: 0x5a946040 0 1 0 0
ath10k_pci 0002:01:00.0: [494]: 0x59909040 0 1 0 0
ath10k_pci 0002:01:00.0: [495]: 0x5ae5a040 0 1 0 0
ath10k_pci 0002:01:00.0: [496]: 0x58096040 0 1 0 0
ath10k_pci 0002:01:00.0: [497]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [498]: 0x580c0642 0 0 0 0
ath10k_pci 0002:01:00.0: [499]: 0x5c1e0040 0 1 0 0
ath10k_pci 0002:01:00.0: [500]: 0x58153040 0 1 0 0
ath10k_pci 0002:01:00.0: [501]: 0x58129040 0 1 0 0
ath10k_pci 0002:01:00.0: [502]: 0x5952f040 0 1 0 0
ath10k_pci 0002:01:00.0: [503]: 0x59535040 0 1 0 0
ath10k_pci 0002:01:00.0: [504]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [505]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [506]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [507]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [508]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [509]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [510]: 0x594a0010 0 0 0 1
ath10k_pci 0002:01:00.0: [511]: 0x580c0042 0 0 0 0
ath10k_pci 0002:01:00.0: [512]: 0x5adcc040 0 1 0 0
ath10k_pci 0002:01:00.0: [513]: 0x5cf3d040 0 1 0 0
ath10k_pci 0002:01:00.0: [514]: 0x5c1e9040 64 1 0 0
ath10k_pci 0002:01:00.0: [515]: 0x00000000 0 0 0 0
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Timothy Redaelli [Tue, 27 Mar 2018 08:25:25 +0000 (11:25 +0300)]
ath9k: fix DFS detector synchronization
some userspace programs (e.g. hostapd) need to set the regulatory domain
before selecting the operating channel. Synchronize DFS detector regardless of
the value of ah->curchan, to avoid situations where wireless scan can't be done
on some 5GHz sub-bands, because dfs_region is constantly UNSET.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Timothy Redaelli <tredaelli@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tobin C. Harding [Thu, 15 Mar 2018 02:31:25 +0000 (13:31 +1100)]
rsi: Remove stack VLA usage
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently rsi code uses a VLA based on a function argument to
`rsi_sdio_load_data_master_write()`. The function call chain is
Both these functions
rsi_sdio_reinit_device()
rsi_probe()
start the call chain:
rsi_hal_device_init()
rsi_load_fw()
auto_fw_upgrade()
ping_pong_write()
rsi_sdio_load_data_master_write()
[Without familiarity with the code] it appears that none of the 4 locks
mutex
rx_mutex
tx_mutex
tx_bus_mutex
are held when `rsi_sdio_load_data_master_write()` is called. It is therefore
safe to use kmalloc with GFP_KERNEL.
We can avoid using the VLA by using `kmalloc()` and free'ing the memory on all
exit paths.
Change buffer from 'u8 array' to 'u8 *'. Call `kmalloc()` to allocate memory for
the buffer. Using goto statement to call `kfree()` on all return paths.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc()` however this code is only called on initialization
(and re-initialization) so this overhead should not degrade performance.
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ganapathi Bhat [Thu, 15 Mar 2018 06:20:32 +0000 (11:50 +0530)]
mwifiex: remove warnings in mwifiex_cmd_append_11n_tlv()
Fix the following sparse warning in mwifiex_cmd_append_11n_tlv:
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: right side has type int
Fixes:
77423fa73927 ("mwifiex: fix incorrect ht capability problem")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Joe Perches [Fri, 23 Mar 2018 22:54:37 +0000 (15:54 -0700)]
wireless: Use octal not symbolic permissions
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arnd Bergmann [Thu, 15 Mar 2018 21:18:24 +0000 (22:18 +0100)]
Bluetooth: btrsi: rework dependencies
The linkage between the bluetooth driver and the wireless
driver is not defined properly, leading to build problems
such as:
warning: (BT_HCIRSI) selects RSI_COEX which has unmet direct dependencies (NETDEVICES && WLAN && WLAN_VENDOR_RSI && BT_HCIRSI && RSI_91X)
drivers/net/wireless/rsi/rsi_91x_main.o: In function `rsi_read_pkt':
(.text+0x205): undefined reference to `rsi_bt_ops'
As the dependency is actually the reverse (RSI_91X uses
the BT_RSI driver, not the other way round), this changes
the dependency to match, and enables the bluetooth driver
from the RSI_COEX symbol.
Fixes:
38aa4da50483 ("Bluetooth: btrsi: add new rsi bluetooth driver")
Acked-by; Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Tue, 27 Mar 2018 07:06:18 +0000 (10:06 +0300)]
Merge ath-next from git://git./linux/kernel/git/kvalo/ath.git
ath.git patches for 4.17. Major changes:
wil6210
* support multiple virtual interfaces
Ramon Fried [Sun, 11 Mar 2018 12:01:43 +0000 (14:01 +0200)]
wcn36xx: Check DXE IRQ reason
IRQ reason was not cheked for errors.
Although error handing is not currently supported, it
will be nice to output an error value to the log if the
DMA operation failed.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ramon Fried [Sun, 11 Mar 2018 12:01:18 +0000 (14:01 +0200)]
wcn36xx: calculate DXE default channel values
DXE channel defaults used hardcoded magic values.
Added bit definitions of the control register and
calculate this values in compilation for clarity.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ramon Fried [Sun, 4 Mar 2018 16:31:34 +0000 (18:31 +0200)]
wcn36xx: calculate DXE control registers values
DXE descriptor control registers used hardcoded magic values. Added bit
definitions of the control register and calculate this values in compilation
for clarity. No functional changes.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Peter Große [Tue, 6 Mar 2018 14:57:18 +0000 (15:57 +0100)]
ath9k: spelling s/premble/preamble/
Signed-off-by: Peter Große <pegro@friiks.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sebastian Gottschall [Sat, 3 Mar 2018 04:10:44 +0000 (05:10 +0100)]
ath9k: fix crash in spectral scan
Fixes crash seen on arm smp systems (gateworks ventana imx6):
Unable to handle kernel NULL pointer dereference at virtual address
00000014
pgd =
80004000
[
00000014] *pgd=
00000000
Internal error: Oops - BUG: 17 [#1] PREEMPT SMP ARM
Modules linked in: ip6table_filter nf_conntrack_ipv6 ip6_tables nf_log_ipv6 nf_defrag_ipv6 shortcut_fe ipcomp6 xfrm_ipcomp xfrm6_tunnel xfrm6_mode_tunnel xfrm6_mode_transport xfrm6_mode_ro xfrm6_mode_beet ip6_tunnel tunnel6 mip6 ah6 esp6 xfrm_algo sit ip_tunnel tunnel4 ipv6 ath10k_pci ath10k_core ath9k ath mac80211 cfg80211 compat ath_pci ath_hal(P) caamalg authencesn authenc caamrng caamhash caam_jr caam cdc_ncm usbnet usbcore sky2 imx2_wdt
CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: P 4.9.85 #19
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task:
bf064980 task.stack:
bf07c000
PC is at relay_buf_full+0xc/0x30
LR is at _674+0x740/0xf10 [ath9k]
pc : [<
8018bce0>] lr : [<
7f1aa604>] psr:
80000013
sp :
bf07dbf0 ip :
bf07dc00 fp :
bf07dbfc
r10:
0000003f r9 :
bf130e00 r8 :
809044b0
r7 :
00000000 r6 :
be67a9f0 r5 :
00000000 r4 :
809043e4
r3 :
c0864c24 r2 :
00000000 r1 :
00000004 r0 :
00000000
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control:
10c5387d Table:
4e6a004a DAC:
00000055
Process ksoftirqd/0 (pid: 3, stack limit = 0xbf07c210)
Stack: (0xbf07dbf0 to 0xbf07e000)
dbe0:
bf07dd04 bf07dc00 7f1aa604 8018bce0
dc00:
00004014 be59e010 bf07dc34 bf07dc18 7f1a7084 7f19c07c be59c010 be6470a0
dc20:
0000096c be648954 bf07dc6c bf07dc38 7f1c286c bf07dd90 bf07dc5c bf07dc48
dc40:
8029ea4c 0000003c 00000001 be59c010 00000094 00000000 00000000 00000000
dc60:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dc80:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dca0:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dcc0:
00000000 00000000 00000000 00000000 00000000 00000000 8010ef24 00000030
dce0:
be94f5e8 be6485a0 bddf0200 be59c010 be6465a0 be6415a0 bf07ddf4 bf07dd08
dd00:
7f1cf800 7f1aa55c 1fc38c4c 00000000 bf07dd58 cccccccd 66666667 be640bc0
dd20:
bf07dd54 be6415a0 1fc38c4c 00000000 00000000 be59c038 be67a9c0 be59e010
dd40:
be67a9f0 be647170 8090c904 be59c010 00000000 00000001 1fc38e84 00000000
dd60:
be640bc0 bddf0200 00000200 00000010 0000003f 00000002 20000013 be59c010
dd80:
8092d940 bf7ca2c0 bf07ddb4 bf07dd98 1fc38c4c 2602003f 0100ff1b 80ff1b00
dda0:
00808080 00000000 00000000 80808080 80808080 80808080 80808080 00008080
ddc0:
00000000 00000000 7f1b62b8 00000002 be6470ec be6470f0 00000000 bf07de98
dde0:
8092d940 be6415a0 bf07de94 bf07ddf8 7f1d1ed8 7f1cf1fc 00000000 00000000
de00:
bf7cc4c0 00000400 be6470f0 bf07de18 8015165c be59c010 8090453c 8090453c
de20:
bf07dec4 be6465a0 8014f614 80148884 0000619a 00000001 bf07c000 00000100
de40:
bf07de78 00000001 7f327850 00000002 afb50401 bf064980 bf07de9c bf07de68
de60:
bf064a00 803cc668 bf064a00 be6470b4 be6470b8 80844180 00000000 bf07de98
de80:
8092d940 bf07c000 bf07dec4 bf07de98 80124d18 7f1d1c44 80124c94 00000000
dea0:
00000006 80902098 80902080 40000006 00000100 bf07c000 bf07df24 bf07dec8
dec0:
8012501c 80124ca0 bf7cc4c0 bf064980 be95e1c0 04208040 80902d00 000061c7
dee0:
0000000a 80600b54 8092d940 808441f8 80902080 bf07dec8 bf03b200 bf07c000
df00:
bf03b200 8090fe54 00000000 00000000 00000000 00000000 bf07df34 bf07df28
df20:
80125148 80124f28 bf07df5c bf07df38 8013deb4 8012511c 00000000 bf03b240
df40:
bf03b200 8013dc90 00000000 00000000 bf07dfac bf07df60 8013ad40 8013dc9c
df60:
70448040 00000001 00000000 bf03b200 00000000 00030003 bf07df78 bf07df78
df80:
00000000 00000000 bf07df88 bf07df88 bf03b240 8013ac48 00000000 00000000
dfa0:
00000000 bf07dfb0 80107760 8013ac54 00000000 00000000 00000000 00000000
dfc0:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dfe0:
00000000 00000000 00000000 00000000 00000013 00000000 8c120004 1190ad04
Backtrace:
[<
8018bcd4>] (relay_buf_full) from [<
7f1aa604>] (_674+0x740/0xf10 [ath9k])
[<
7f1aa550>] (_674 [ath9k]) from [<
7f1cf800>] (_582+0x14b4/0x3708 [ath9k])
r10:
be6415a0 r9:
be6465a0 r8:
be59c010 r7:
bddf0200 r6:
be6485a0 r5:
be94f5e8
r4:
00000030
[<
7f1cf1f0>] (_582 [ath9k]) from [<
7f1d1ed8>] (_735+0x2a0/0xec4 [ath9k])
r10:
be6415a0 r9:
8092d940 r8:
bf07de98 r7:
00000000 r6:
be6470f0 r5:
be6470ec
r4:
00000002
[<
7f1d1c38>] (_735 [ath9k]) from [<
80124d18>] (tasklet_action+0x84/0xf8)
r10:
bf07c000 r9:
8092d940 r8:
bf07de98 r7:
00000000 r6:
80844180 r5:
be6470b8
r4:
be6470b4
[<
80124c94>] (tasklet_action) from [<
8012501c>] (__do_softirq+0x100/0x1f4)
r10:
bf07c000 r9:
00000100 r8:
40000006 r7:
80902080 r6:
80902098 r5:
00000006
r4:
00000000 r3:
80124c94
[<
80124f1c>] (__do_softirq) from [<
80125148>] (run_ksoftirqd+0x38/0x4c)
r10:
00000000 r9:
00000000 r8:
00000000 r7:
00000000 r6:
8090fe54 r5:
bf03b200
r4:
bf07c000
[<
80125110>] (run_ksoftirqd) from [<
8013deb4>] (smpboot_thread_fn+0x224/0x260)
[<
8013dc90>] (smpboot_thread_fn) from [<
8013ad40>] (kthread+0xf8/0x100)
r9:
00000000 r8:
00000000 r7:
8013dc90 r6:
bf03b200 r5:
bf03b240 r4:
00000000
[<
8013ac48>] (kthread) from [<
80107760>] (ret_from_fork+0x14/0x34)
r7:
00000000 r6:
00000000 r5:
8013ac48 r4:
bf03b240
Code:
e89da800 e1a0c00d e92dd800 e24cb004 (
e5901014)
---[ end trace
dddf11ac9111b272 ]---
Kernel panic - not syncing: Fatal exception in interrupt
CPU1: stopping
CPU: 1 PID: 0 Comm: swapper/1 Tainted: P D 4.9.85 #19
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<
8010a708>] (dump_backtrace) from [<
8010a99c>] (show_stack+0x18/0x1c)
r7:
bf093f58 r6:
20000193 r5:
809168e8 r4:
00000000
[<
8010a984>] (show_stack) from [<
802a09c4>] (dump_stack+0x94/0xa8)
[<
802a0930>] (dump_stack) from [<
8010d184>] (handle_IPI+0xe8/0x180)
r7:
bf093f58 r6:
00000000 r5:
00000001 r4:
808478c4
[<
8010d09c>] (handle_IPI) from [<
801013e8>] (gic_handle_irq+0x78/0x7c)
r7:
f4000100 r6:
bf093f58 r5:
f400010c r4:
8090467c
[<
80101370>] (gic_handle_irq) from [<
8010b378>] (__irq_svc+0x58/0x8c)
Exception stack(0xbf093f58 to 0xbf093fa0)
3f40:
bf7d62a0 00000000
3f60:
0010a5f4 80113460 bf092000 809043e4 00000002 80904434 bf092008 412fc09a
3f80:
00000000 bf093fb4 bf093fb8 bf093fa8 8010804c 80108050 60000013 ffffffff
r9:
bf092000 r8:
bf092008 r7:
bf093f8c r6:
ffffffff r5:
60000013 r4:
80108050
[<
80108014>] (arch_cpu_idle) from [<
80553c2c>] (default_idle_call+0x30/0x34)
[<
80553bfc>] (default_idle_call) from [<
80158394>] (cpu_startup_entry+0xc4/0xfc)
[<
801582d0>] (cpu_startup_entry) from [<
8010ce40>] (secondary_start_kernel+0x168/0x174)
r7:
8092d2f8 r4:
80913568
[<
8010ccd8>] (secondary_start_kernel) from [<
10101488>] (0x10101488)
r5:
00000055 r4:
4f07806a
Rebooting in 10 seconds..
Reboot failed -- System halted
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Karthikeyan Periyasamy [Mon, 12 Mar 2018 11:39:40 +0000 (17:09 +0530)]
ath10k: Fix kernel panic while using worker (ath10k_sta_rc_update_wk)
When attempt to run worker (ath10k_sta_rc_update_wk) after the station object
(ieee80211_sta) delete will trigger the kernel panic.
This problem arise in AP + Mesh configuration, Where the current node AP VAP
and neighbor node mesh VAP MAC address are same. When the current mesh node
try to establish the mesh link with neighbor node, driver peer creation for
the neighbor mesh node fails due to duplication MAC address. Already the AP
VAP created with same MAC address.
It is caused by the following scenario steps.
Steps:
1. In above condition, ath10k driver sta_state callback (ath10k_sta_state)
fails to do the state change for a station from IEEE80211_STA_NOTEXIST
to IEEE80211_STA_NONE due to peer creation fails. Sta_state callback is
called from ieee80211_add_station() to handle the new station
(neighbor mesh node) request from the wpa_supplicant.
2. Concurrently ath10k receive the sta_rc_update callback notification from
the mesh_neighbour_update() to handle the beacon frames of the above
neighbor mesh node. since its atomic callback, ath10k driver queue the
work (ath10k_sta_rc_update_wk) to handle rc update.
3. Due to driver sta_state callback fails (step 1), mac80211 free the station
object.
4. When the worker (ath10k_sta_rc_update_wk) scheduled to run, it will access
the station object which is already deleted. so it will trigger kernel
panic.
Added the peer exist check in sta_rc_update callback before queue the work.
Kernel Panic log:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
pgd =
c0204000
[
00000000] *pgd=
00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
CPU: 1 PID: 1833 Comm: kworker/u4:2 Not tainted 3.14.77 #1
task:
dcef0000 ti:
d72b6000 task.ti:
d72b6000
PC is at pwq_activate_delayed_work+0x10/0x40
LR is at pwq_activate_delayed_work+0xc/0x40
pc : [<
c023f988>] lr : [<
c023f984>] psr:
40000193
sp :
d72b7f18 ip :
0000007a fp :
d72b6000
r10:
00000000 r9 :
dd404414 r8 :
d8c31998
r7 :
d72b6038 r6 :
00000004 r5 :
d4907ec8 r4 :
dcee1300
r3 :
ffffffe0 r2 :
00000000 r1 :
00000001 r0 :
00000000
Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control:
10c5787d Table:
595bc06a DAC:
00000015
...
Process kworker/u4:2 (pid: 1833, stack limit = 0xd72b6238)
Stack: (0xd72b7f18 to 0xd72b8000)
7f00:
00000001 dcee1300
7f20:
00000001 c02410dc d8c31980 dd404400 dd404400 c0242790 d8c31980 00000089
7f40:
00000000 d93e1340 00000000 d8c31980 c0242568 00000000 00000000 00000000
7f60:
00000000 c02474dc 00000000 00000000 000000f8 d8c31980 00000000 00000000
7f80:
d72b7f80 d72b7f80 00000000 00000000 d72b7f90 d72b7f90 d72b7fac d93e1340
7fa0:
c0247404 00000000 00000000 c0208d20 00000000 00000000 00000000 00000000
7fc0:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
7fe0:
00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<
c023f988>] (pwq_activate_delayed_work) from [<
c02410dc>] (pwq_dec_nr_in_flight+0x58/0xc4)
[<
c02410dc>] (pwq_dec_nr_in_flight) from [<
c0242790>] (worker_thread+0x228/0x360)
[<
c0242790>] (worker_thread) from [<
c02474dc>] (kthread+0xd8/0xec)
[<
c02474dc>] (kthread) from [<
c0208d20>] (ret_from_fork+0x14/0x34)
Code:
e92d4038 e1a05000 ebffffbc[69210.619376] SMP: failed to stop secondary CPUs
Rebooting in 3 seconds..
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Carl Huang [Mon, 5 Mar 2018 06:44:02 +0000 (14:44 +0800)]
ath10k: fix use-after-free in ath10k_wmi_cmd_send_nowait
The skb may be freed in tx completion context before
trace_ath10k_wmi_cmd is called. This can be easily captured when
KASAN(Kernel Address Sanitizer) is enabled. The fix is to move
trace_ath10k_wmi_cmd before the send operation. As the ret has no
meaning in trace_ath10k_wmi_cmd then, so remove this parameter too.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ramon Fried [Wed, 14 Mar 2018 10:14:11 +0000 (12:14 +0200)]
wcn36xx: reduce verbosity of drivers messages
Whenever the WLAN interface is started the FW
version and caps are printed.
The caps now will be displayed only in debug mode.
Firmware version will be displayed only once on first
startup of the interface.
Change-Id: I4db6ea7f384fe15eebe4c3ddb1d1ccab00094332
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sriram R [Wed, 14 Mar 2018 10:14:10 +0000 (12:14 +0200)]
ath: fix false radar detection in JP region
This fixes false radar detection (of radar type 7)
in Japan region by correcting the radar pulse type
to Chirp as per specification.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maharaja Kennadyrajan [Wed, 14 Mar 2018 10:14:08 +0000 (12:14 +0200)]
ath10k: debugfs support to get final TPC stats for 10.4 variants
Export the final Transmit Power Control (TPC) value, which is the
minimum of control power and existing TPC value to user space via
a new debugfs file "tpc_stats_final" to help with debugging.
It works with the new wmi cmd and event introduced in 10.4 firmware
branch.
WMI command ID: WMI_PDEV_GET_TPC_TABLE_CMDID
WMI event ID: WMI_PDEV_TPC_TABLE_EVENTID
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
$ cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
TPC config for channel 5180 mode 10
CTL = 0x 0 Reg. Domain = 58
Antenna Gain = 0 Reg. Max Antenna Gain = 0
Power Limit = 60 Reg. Max Power = 60
Num tx chains = 2 Num supported rates = 109
******************* CDD POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
******************* STBC POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
***********************************
TXBF not supported
**********************************
The existing tpc_stats debugfs file provides the dump
which is minimum of target power and regulatory domain.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats
Hardware_used: QCA4019
Firmware version: firmware-5.bin_10.4-3.0-00209
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Vasanthakumar Thiagarajan [Wed, 14 Mar 2018 10:14:06 +0000 (12:14 +0200)]
ath10k: add sta rx packet stats per tid
Added per tid sta counters for the following
- Total number MSDUs received from firmware
- Number of MSDUs received with errors like decryption, crc, mic ,etc.
- Number of MSDUs dropped in the driver
- A-MPDU/A-MSDU subframe stats
- Number of MSDUS passed to mac80211
All stats other than A-MPDU stats are only for received data frames.
A-MPDU stats might have stats for management frames when monitor
interface is active where management frames are notified both in wmi
and HTT interfaces.
These per tid stats can be enabled with tid bitmask through a debugfs
like below
echo <tid_bitmask> > /sys/kernel/debug/ieee80211/phyX/ath10k/sta_tid_stats_mask
tid 16 (tid_bitmask 0x10000) is used for non-qos data/management frames
The stats are read from
/sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/<sta_mac>/dump_tid_stats
Sample output:
To enable rx stats for tid 0, 5 and 6,
echo 0x00000061 > /sys/kernel/debug/ieee80211/phy0/ath10k/sta_tid_stats_mask
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan15/stations/8c\:fd\:f0\:0a\:8e\:df/dump_tid_stats
Driver Rx pkt stats per tid, ([tid] count)
------------------------------------------
MSDUs from FW [00] 2567 [05] 3178 [06] 1089
MSDUs unchained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:chained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:filtered [00] 0 [05] 0 [06] 0
MSDUs queued for mac80211 [00] 2567 [05] 3178 [06] 1089
MSDUs with error:fcs_err [00] 0 [05] 0 [06] 2
MSDUs with error:tkip_err [00] 0 [05] 0 [06] 0
MSDUs with error:crypt_err [00] 0 [05] 0 [06] 0
MSDUs with error:peer_idx_inval [00] 0 [05] 0 [06] 0
A-MPDU num subframes upto 10 [00] 2567 [05] 3178 [06] 1087
A-MPDU num subframes 11-20 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 21-30 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 31-40 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 41-50 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 51-60 [00] 0 [05] 0 [06] 0
A-MPDU num subframes >60 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 1 [00] 2567 [05] 3178 [06] 1089
A-MSDU num subframes 2 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 3 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 4 [00] 0 [05] 0 [06] 0
A-MSDU num subframes >4 [00] 0 [05] 0 [06] 0
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David S. Miller [Mon, 26 Mar 2018 01:27:38 +0000 (21:27 -0400)]
Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot [Fri, 23 Mar 2018 19:47:42 +0000 (03:47 +0800)]
tipc: tipc_disc_addr_trial_msg() can be static
Fixes:
25b0b9c4e835 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Jon Maloy jon.maloy@ericsson.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 23 Mar 2018 11:36:15 +0000 (14:36 +0300)]
ibmvnic: Potential NULL dereference in clean_one_tx_pool()
There is an && vs || typo here, which potentially leads to a NULL
dereference.
Fixes:
e9e1e97884b7 ("ibmvnic: Update TX pool cleaning routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Fri, 23 Mar 2018 11:35:49 +0000 (17:05 +0530)]
cxgb4: support new ISSI flash parts
Add support for new 32MB and 64MB ISSI (Integrated Silicon
Solution, Inc.) FLASH parts.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Fri, 23 Mar 2018 11:33:10 +0000 (17:03 +0530)]
cxgb4: depend on firmware event for link status
Depend on the firmware sending us link status changes,
rather than assuming that the link goes down upon L1
configuration.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun Vynipadath [Fri, 23 Mar 2018 10:18:46 +0000 (15:48 +0530)]
cxgb4: copy vlan_id in ndo_get_vf_config
Copy vlan_id to get it displayed in vf info.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudhar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun Vynipadath [Fri, 23 Mar 2018 09:55:10 +0000 (15:25 +0530)]
cxgb4: Setup FW queues before registering netdev
When NetworkManager is enabled, there are chances that interface up
is called even before probe completes. This means we have not yet
allocated the FW sge queues, hence rest of ingress queue allocation
wont be proper. Fix this by calling setup_fw_sge_queues() before
register_netdev().
Fixes:
0fbc81b3ad51 ('chcr/cxgb4i/cxgbit/RDMA/cxgb4: Allocate resources dynamically for all cxgb4 ULD's')
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 26 Mar 2018 00:48:26 +0000 (20:48 -0400)]
Merge branch 'broadcom-Adaptive-interrupt-coalescing'
Florian Fainelli says:
====================
net: broadcom: Adaptive interrupt coalescing
This patch series adds adaptive interrupt coalescing for the Gigabit Ethernet
drivers SYSTEMPORT and GENET.
This really helps lower the interrupt count and system load, as measured by
vmstat for a Gigabit TCP RX session:
SYSTEMPORT:
without:
1 0 0 192188 0 25472 0 0 0 0 122100 38870 1 42 57 0 0
[ ID] Interval Transfer Bandwidth
[ 4] 0.0-10.0 sec 1.03 GBytes 884 Mbits/sec
with:
1 0 0 192288 0 25468 0 0 0 0 58806 44401 0 100 0 0 0
[ 5] 0.0-10.0 sec 1.04 GBytes 888 Mbits/sec
GENET:
without:
1 0 0
1170404 0 25420 0 0 0 0 130785 63402 2 85 12 0 0
[ ID] Interval Transfer Bandwidth
[ 4] 0.0-10.0 sec 1.04 GBytes 888 Mbits/sec
with:
1 0 0
1170560 0 25420 0 0 0 0 50610 48477 0 100 0 0 0
[ 5] 0.0-10.0 sec 1.05 GBytes 899 Mbits/sec
Please look at the implementation and let me know if you see any problems, this
was largely inspired by bnxt_en.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 23 Mar 2018 01:19:33 +0000 (18:19 -0700)]
net: bcmgenet: Add support for adaptive RX coalescing
Unlike the moder modern SYSTEMPORT hardware, we do not have a
configurable TDMA timeout, which limits us to implement adaptive RX
interrupt coalescing only. We have each of our RX rings implement a
bcmgenet_net_dim structure which holds an interrupt counter, number of
packets, bytes, and a container for a net_dim instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 23 Mar 2018 01:19:32 +0000 (18:19 -0700)]
net: systemport: Implement adaptive interrupt coalescing
Implement support for adaptive RX and TX interrupt coalescing using
net_dim. We have each of our TX ring and our single RX ring implement a
bcm_sysport_net_dim structure which holds an interrupt counter, number
of packets, bytes, and a container for a net_dim instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 26 Mar 2018 00:43:42 +0000 (20:43 -0400)]
Merge branch 'mv88e6xxx-module-reloading'
Andrew Lunn says:
====================
Fixes to allow mv88e6xxx module to be reloaded
As reported by Uwe Kleine-König, the interrupt trigger is first
configured by DT and then reconfigured to edge. This results in a
failure on EPROBE_DEFER, or if the module is unloaded and reloaded.
A second crash happens on module reload due to a missing call to the
common IRQ free code when using polled interrupts.
With these fixes in place, it becomes possible to load and unload the
kernel modules a few times without it crashing.
v2: Fix the ü in Künig a couple of times
v3: But the ü should be an ö!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 25 Mar 2018 21:43:15 +0000 (23:43 +0200)]
net: dsa: mv88e6xxx: Call the common IRQ free code
When free'ing the polled IRQs, call the common irq free code.
Otherwise the interrupts are left registered, and when we come to load
the driver a second time, we get an Opps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 25 Mar 2018 21:43:14 +0000 (23:43 +0200)]
net: dsa: mv88e6xxx: Use the DT IRQ trigger mode
By calling request_threaded_irq() with the flag IRQF_TRIGGER_FALLING
we override the trigger mode provided in device tree. And the
interrupt is actually active low, which is what all the current device
tree descriptions use.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Mashak [Sun, 25 Mar 2018 21:20:06 +0000 (17:20 -0400)]
tc-testing: updated police, mirred, skbedit and skbmod with more tests
Added extra test cases for control actions (reclassify, pipe etc.),
cookies, max index value and police args sanity check.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 25 Mar 2018 21:07:41 +0000 (17:07 -0400)]
Merge branch 'hv_netvsc-Fix-improve-RX-path-error-handling'
Haiyang Zhang says:
====================
hv_netvsc: Fix/improve RX path error handling
Fix the status code returned to the host. Also add range
check for rx packet offset and length.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Thu, 22 Mar 2018 19:01:14 +0000 (12:01 -0700)]
hv_netvsc: Add range checking for rx packet offset and length
This patch adds range checking for rx packet offset and length.
It may only happen if there is a host side bug.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Thu, 22 Mar 2018 19:01:13 +0000 (12:01 -0700)]
hv_netvsc: Fix the return status in RX path
As defined in hyperv_net.h, the NVSP_STAT_SUCCESS is one not zero.
Some functions returns 0 when it actually means NVSP_STAT_SUCCESS.
This patch fixes them.
In netvsc_receive(), it puts the last RNDIS packet's receive status
for all packets in a vmxferpage which may contain multiple RNDIS
packets.
This patch puts NVSP_STAT_FAIL in the receive completion if one of
the packets in a vmxferpage fails.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 25 Mar 2018 20:46:05 +0000 (16:46 -0400)]
Merge branch 'net-permit-skb_segment-on-head_frag-frag_list-skb'
Yonghong Song says:
====================
net: permit skb_segment on head_frag frag_list skb
One of our in-house projects, bpf-based NAT, hits a kernel BUG_ON at
function skb_segment(), line 3667. The bpf program attaches to
clsact ingress, calls bpf_skb_change_proto to change protocol
from ipv4 to ipv6 or from ipv6 to ipv4, and then calls bpf_redirect
to send the changed packet out.
...
3665 while (pos < offset + len) {
3666 if (i >= nfrags) {
3667 BUG_ON(skb_headlen(list_skb));
...
The triggering input skb has the following properties:
list_skb = skb->frag_list;
skb->nfrags != NULL && skb_headlen(list_skb) != 0
and skb_segment() is not able to handle a frag_list skb
if its headlen (list_skb->len - list_skb->data_len) is not 0.
Patch #1 provides a simple solution to avoid BUG_ON. If
list_skb->head_frag is true, its page-backed frag will
be processed before the list_skb->frags.
Patch #2 provides a test case in test_bpf module which
constructs a skb and calls skb_segment() directly. The test
case is able to trigger the BUG_ON without Patch #1.
The patch has been tested in the following setup:
ipv6_host <-> nat_server <-> ipv4_host
where nat_server has a bpf program doing ipv4<->ipv6
translation and forwarding through clsact hook
bpf_skb_change_proto.
Changelog:
v5 -> v6:
. Added back missed BUG_ON(!nfrags) for zero
skb_headlen(skb) case, plus a couple of
cosmetic changes, from Alexander.
v4 -> v5:
. Replace local variable head_frag with
a static inline function skb_head_frag_to_page_desc
which gets the head_frag on-demand. This makes
code more readable and also does not increase
the stack size, from Alexander.
. Remove the "if(nfrags)" guard for skb_orphan_frags
and skb_zerocopy_clone as I found that they can
handle zero-frag skb (with non-zero skb_headlen(skb))
properly.
. Properly release segment list from skb_segment()
in the test, from Eric.
v3 -> v4:
. Remove dynamic memory allocation and use rewinding
for both index and frag to remove one branch in fast path,
from Alexander.
. Fix a bunch of issues in test_bpf skb_segment() test,
including proper way to allocate skb, proper function
argument for skb_add_rx_frag and not freeint skb, etc.,
from Eric.
v2 -> v3:
. Use starting frag index -1 (instead of 0) to
special process head_frag before other frags in the skb,
from Alexander Duyck.
v1 -> v2:
. Removed never-hit BUG_ON, spotted by Linyu Yuan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Wed, 21 Mar 2018 23:31:04 +0000 (16:31 -0700)]
net: bpf: add a test for skb_segment in test_bpf module
Without the previous commit,
"modprobe test_bpf" will have the following errors:
...
[ 98.149165] ------------[ cut here ]------------
[ 98.159362] kernel BUG at net/core/skbuff.c:3667!
[ 98.169756] invalid opcode: 0000 [#1] SMP PTI
[ 98.179370] Modules linked in:
[ 98.179371] test_bpf(+)
...
which triggers the bug the previous commit intends to fix.
The skbs are constructed to mimic what mlx5 may generate.
The packet size/header may not mimic real cases in production. But
the processing flow is similar.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Wed, 21 Mar 2018 23:31:03 +0000 (16:31 -0700)]
net: permit skb_segment on head_frag frag_list skb
One of our in-house projects, bpf-based NAT, hits a kernel BUG_ON at
function skb_segment(), line 3667. The bpf program attaches to
clsact ingress, calls bpf_skb_change_proto to change protocol
from ipv4 to ipv6 or from ipv6 to ipv4, and then calls bpf_redirect
to send the changed packet out.
3472 struct sk_buff *skb_segment(struct sk_buff *head_skb,
3473 netdev_features_t features)
3474 {
3475 struct sk_buff *segs = NULL;
3476 struct sk_buff *tail = NULL;
...
3665 while (pos < offset + len) {
3666 if (i >= nfrags) {
3667 BUG_ON(skb_headlen(list_skb));
3668
3669 i = 0;
3670 nfrags = skb_shinfo(list_skb)->nr_frags;
3671 frag = skb_shinfo(list_skb)->frags;
3672 frag_skb = list_skb;
...
call stack:
...
#1 [
ffff883ffef03558] __crash_kexec at
ffffffff8110c525
#2 [
ffff883ffef03620] crash_kexec at
ffffffff8110d5cc
#3 [
ffff883ffef03640] oops_end at
ffffffff8101d7e7
#4 [
ffff883ffef03668] die at
ffffffff8101deb2
#5 [
ffff883ffef03698] do_trap at
ffffffff8101a700
#6 [
ffff883ffef036e8] do_error_trap at
ffffffff8101abfe
#7 [
ffff883ffef037a0] do_invalid_op at
ffffffff8101acd0
#8 [
ffff883ffef037b0] invalid_op at
ffffffff81a00bab
[exception RIP: skb_segment+3044]
RIP:
ffffffff817e4dd4 RSP:
ffff883ffef03860 RFLAGS:
00010216
RAX:
0000000000002bf6 RBX:
ffff883feb7aaa00 RCX:
0000000000000011
RDX:
ffff883fb87910c0 RSI:
0000000000000011 RDI:
ffff883feb7ab500
RBP:
ffff883ffef03928 R8:
0000000000002ce2 R9:
00000000000027da
R10:
000001ea00000000 R11:
0000000000002d82 R12:
ffff883f90a1ee80
R13:
ffff883fb8791120 R14:
ffff883feb7abc00 R15:
0000000000002ce2
ORIG_RAX:
ffffffffffffffff CS: 0010 SS: 0018
#9 [
ffff883ffef03930] tcp_gso_segment at
ffffffff818713e7
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 25 Mar 2018 20:24:34 +0000 (16:24 -0400)]
Merge branch '10GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-03-23
This series contains updates to ixgbe and ixgbevf only.
Paul adds status register reads to reduce a potential race condition
where registers can read 0xFFFFFFFF during a PCI reset, which in turn
causes the driver to remove the adapter. Then fixes an assignment
operation with an "OR" operation.
Shannon Nelson provides several IPsec offload cleanups to ixgbe, as well as a
patch to enable TSO with IPsec offload.
Tony provides the much anticipated XDP support for ixgbevf. Currently,
pass, drop and XDP_TX actions are supported, as well as meta data and
stats reporting.
Björn Töpel tweaks the page counting for XDP_REDIRECT, since a page can
have its reference count decreased via the xdp_do_redirect() call.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 25 Mar 2018 20:18:55 +0000 (16:18 -0400)]
Merge branch 'liquidio-Tx-queue-cleanup'
Intiyaz Basha says:
====================
liquidio: Tx queue cleanup
Moved some common function to octeon_network.h
Removed some unwanted functions and checks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha [Sat, 24 Mar 2018 00:37:44 +0000 (17:37 -0700)]
liquidio: Renamed txqs_start to start_txqs
For consistency renaming txqs_start to start_txqs
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha [Sat, 24 Mar 2018 00:37:41 +0000 (17:37 -0700)]
liquidio: Renamed txqs_stop to stop_txqs
For consistency renaming txqs_stop to stop_txqs
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha [Sat, 24 Mar 2018 00:37:39 +0000 (17:37 -0700)]
liquidio: Renamed txqs_wake to wake_txqs
For consistency renaming txqs_wake to wake_txqs
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha [Sat, 24 Mar 2018 00:37:36 +0000 (17:37 -0700)]
liquidio: Function call skb_iq for deriving queue from skb
Using skb_iq function for deriving queue from skb
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha [Sat, 24 Mar 2018 00:37:33 +0000 (17:37 -0700)]
liquidio: Removed one line function wake_q
Removing one line function wake_q
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha [Sat, 24 Mar 2018 00:37:30 +0000 (17:37 -0700)]
liquidio: Removed one line function stop_q
Removing one line function stop_q
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha [Sat, 24 Mar 2018 00:37:28 +0000 (17:37 -0700)]
liquidio: Removed netif_is_multiqueue check
Removing checks for netif_is_multiqueue.
Configuring single queue will be a multiqueue netdev with one queues.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha [Sat, 24 Mar 2018 00:37:25 +0000 (17:37 -0700)]
liquidio: Removed start_txq function
Removing start_txq function from VF and PF files
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>