OSDN Git Service
David Herrmann [Mon, 26 Aug 2013 17:14:46 +0000 (19:14 +0200)]
Input: introduce BTN/ABS bits for drums and guitars
There are a bunch of guitar and drums devices out there that all report
similar data. To avoid reporting this as BTN_MISC or ABS_MISC, we
allocate some proper namespace for them. Note that most of these devices
are toys and we cannot report any sophisticated physics via this API.
I did some google-images research and tried to provide definitions that
work with all common devices. That's why I went with 4 toms, 4 cymbals,
one bass, one hi-hat. I haven't seen other drums and I doubt that we need
any additions to that. Anyway, the naming-scheme is intentionally done in
an extensible way.
For guitars, we support 5 frets (normally aligned vertically, compared to
the real horizontal layouts), a single strum-bar with up/down directions,
an optional fret-board and a whammy-bar.
Most of the devices provide pressure values so I went with ABS_* bits. If
we ever support devices which only provide digital input, we have to
decide whether to emulate pressure data or add additional BTN_* bits.
If someone is not familiar with these devices, here are two pictures which
provide almost all introduced interfaces (or try the given keywords
with a google-image search):
Guitar: ("guitar hero world tour guitar")
http://images1.wikia.nocookie.net/__cb20120911023442/applezone/es/images/f/f9/Wii_Guitar.jpg
Drums: ("guitar hero drums")
http://oyster.ignimgs.com/franchises/images/03/55/35526_band-hero-drum-set-hands-on-
20090929040735768.jpg
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
David Herrmann [Sun, 4 Aug 2013 16:50:10 +0000 (18:50 +0200)]
HID: wiimote: work around broken DRM_KAI on GEN10
GEN10 and earlier devices seem to not support DRM_KAI if we run in basic
IR mode. Use DRM_KAIE instead. This might increases overhead slightly as
the extension port is read and streamed but we stream accelerometer data
constantly, too, so this is negligible.
Note that our parsers are hardcoded on IR-formats, so we cannot actually
use 96-bit IR DRMs for basic IR data. We would have to adjust the parsers.
But as only GEN20 and newer support this, we simply avoid mixed DRMs.
This fixes a bug where GEN10 devices didn't provide IR data if
accelerometer and IR are enabled simultaneously. As a workaround, you can
enable DRM_KAIE without this patch via (disables device power-management):
echo "37" >/sys/kernel/debug/hid/<dev>/drm
Cc: stable@vger.kernel.org
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reported-by: Nicolas Adenis-Lamarre <nicolas.adenis.lamarre@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Andy Shevchenko [Fri, 2 Aug 2013 11:08:00 +0000 (14:08 +0300)]
HID: hid-holtekff: don't push static constants on stack for %*ph
There is no need to pass constants via stack. The width may be explicitly
specified in the format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Andy Shevchenko [Fri, 2 Aug 2013 11:07:15 +0000 (14:07 +0300)]
HID: i2c-hid: don't push static constants on stack for %*ph
There is no need to pass constants via stack. The width may be explicitly
specified in the format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Peter Hurley [Wed, 31 Jul 2013 21:17:58 +0000 (17:17 -0400)]
HID: logitech-dj: Fix non-atomic kmalloc in logi_dj_ll_input_event()
The ll_driver's .hidinput_input_event() method is called from
atomic context [1]. Use GFP_ATOMIC for allocation of the
synthesized hid report.
BUG: sleeping function called from invalid context at /home/peter/src/kernels/next/mm/slub.c:941
in_atomic(): 1, irqs_disabled(): 1, pid: 2095, name: Xorg
INFO: lockdep is turned off.
irq event stamp:
1502178
hardirqs last enabled at (
1502177): [<
ffffffff81785e55>] _raw_spin_unlock_irqrestore+0x65/0x80
hardirqs last disabled at (
1502178): [<
ffffffff8178632a>] common_interrupt+0x6a/0x6f
softirqs last enabled at (
1501802): [<
ffffffff81051ed3>] __do_softirq+0x183/0x420
softirqs last disabled at (
1501799): [<
ffffffff81052315>] irq_exit+0xb5/0xc0
CPU: 3 PID: 2095 Comm: Xorg Not tainted 3.11-next-
20130725-xeon+lockdep #
20130725
Hardware name: Dell Inc. Precision WorkStation T5400 /0RW203, BIOS A11 04/30/2012
ffffffff81a662e0 ffff8802adcf9ca8 ffffffff8177c330 0000000000000000
ffff8802a76d2440 ffff8802adcf9cd8 ffffffff810867d0 ffff8802a7ac8000
0000000000000010 00000000ffffffff 00000000000000d0 ffff8802adcf9d38
Call Trace:
[<
ffffffff8177c330>] dump_stack+0x4f/0x84
[<
ffffffff810867d0>] __might_sleep+0x140/0x1f0
[<
ffffffff811ad93b>] __kmalloc+0x6b/0x2e0
[<
ffffffffa026cb08>] ? hid_alloc_report_buf+0x28/0x30 [hid]
[<
ffffffffa026cb08>] hid_alloc_report_buf+0x28/0x30 [hid]
[<
ffffffffa00700b0>] logi_dj_ll_input_event+0xb0/0x1b0 [hid_logitech_dj]
[<
ffffffff815a559e>] input_handle_event+0x8e/0x540
[<
ffffffff815a5aad>] ? input_inject_event+0x5d/0x220
[<
ffffffff815a5c10>] input_inject_event+0x1c0/0x220
[<
ffffffff815a5a94>] ? input_inject_event+0x44/0x220
[<
ffffffff81181660>] ? might_fault+0xa0/0xb0
[<
ffffffff81181617>] ? might_fault+0x57/0xb0
[<
ffffffff815a909e>] evdev_write+0xde/0x160
[<
ffffffff811c0ad8>] vfs_write+0xc8/0x1f0
[<
ffffffff811c0fe5>] SyS_write+0x55/0xa0
[<
ffffffff8178e682>] system_call_fastpath+0x16/0x1b
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Olivier Scherler [Sat, 27 Jul 2013 17:20:02 +0000 (19:20 +0200)]
HID: Add new driver for non-compliant Xin-Mo devices.
The driver currently only supports the Dual Arcade controller.
It fixes the negative axis event values (the devices sends -2) to match the
logical axis minimum of the HID report descriptor (the report announces -1).
It is needed because hid-input discards out of bounds values.
Signed-off-by: Olivier Scherler <oscherler@ithink.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jingoo Han [Fri, 19 Jul 2013 06:53:16 +0000 (15:53 +0900)]
HID: replace strict_strtoul() with kstrtoul()
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Mon, 22 Jul 2013 15:11:44 +0000 (17:11 +0200)]
HID: fix unused rsize usage
27ce4050 ("HID: fix data access in implement()") by mistake removed
a setting of buffer size in hidp. Fix that by putting it back.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Wed, 10 Jul 2013 17:56:27 +0000 (19:56 +0200)]
HID: fix data access in implement()
implement() is setting bytes in LE data stream. In case the data is not
aligned to 64bits, it reads past the allocated buffer. It doesn't really
change any value there (it's properly bitmasked), but in case that this
read past the boundary hits a page boundary, pagefault happens when
accessing 64bits of 'x' in implement(), and kernel oopses.
This happens much more often when numbered reports are in use, as the
initial 8bit skip in the buffer makes the whole process work on values
which are not aligned to 64bits.
This problem dates back to attempts in 2005 and 2006 to make implement()
and extract() as generic as possible, and even back then the problem
was realized by Adam Kroperlin, but falsely assumed to be impossible
to cause any harm:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg47690.html
I have made several attempts at fixing it "on the spot" directly in
implement(), but the results were horrible; the special casing for processing
last 64bit chunk and switching to different math makes it unreadable mess.
I therefore took a path to allocate a few bytes more which will never make
it into final report, but are there as a cushion for all the 64bit math
operations happening in implement() and extract().
All callers of hid_output_report() are converted at the same time to allocate
the buffer by newly introduced hid_alloc_report_buf() helper.
Bruno noticed that the whole raw_size test can be dropped as well, as
hid_alloc_report_buf() makes sure that the buffer is always of a proper
size.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Benjamin Tissoires [Mon, 15 Jul 2013 08:12:18 +0000 (10:12 +0200)]
HID: kye: Add report fixup for Genius Gx Imperator Keyboard
Genius Gx Imperator Keyboard presents the same problem in its report
descriptors than Genius Gila Gaming Mouse.
Use the same fixup for both.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=928561
Reported-and-tested-by: Honza Brazdil <jbrazdil@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Paul Chavent [Sun, 7 Jul 2013 15:43:56 +0000 (17:43 +0200)]
HID: core: fix hid delimiter local tag parsing.
When device with the DELIMITER tag in its report descriptor is encountered
during parsing, it's mistakenly immediately refused by HID core for no
justifiable reason.
[jkosina@suse.cz: polish changelog]
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds [Thu, 4 Jul 2013 18:39:00 +0000 (11:39 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- HID battery handling cleanup by David Herrmann
- ELO 4000/4500 driver, which has been finally ported to be proper HID
driver by Jiri Slaby
- ps3remote driver functionality is now provided by generic sony
driver, by Jiri Kosina
- PS2/3 Buzz controllers support, by Colin Leitner
- rework of wiimote driver including full extensions hotpluggin
support, sub-device modularization and speaker support by David
Herrmann
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (55 commits)
HID: wacom: Intuos4 battery charging changes
HID: i2c-hid: support sending HID output reports using the output register
HID: kye: Add report fixup for Genius Gila Gaming mouse
HID: wiimote: support Nintendo Wii U Pro Controller
Input: make gamepad API keycodes more clear
input: document gamepad API and add extra keycodes
HID: explain out-of-range check better
HID: fix false positive out of range values
HID: wiimote: fix coccinelle warnings
HID: roccat: check cdev_add return value
HID: fold ps3remote driver into generic Sony driver
HID: hyperv: convert alloc+memcpy to memdup
HID: core: fix reporting of raw events
HID: wiimote: discard invalid EXT data reports
HID: wiimote: fix classic controller parsing
HID: wiimote: init EXT/MP during device detection
HID: wiimote: fix DRM debug-attr to correctly parse input
HID: wiimote: add MP quirks
HID: wiimote: remove old static extension support
HID: wiimote: add "bboard_calib" attribute
...
Linus Torvalds [Thu, 4 Jul 2013 18:36:50 +0000 (11:36 -0700)]
Merge tag 'md-3.11' of git://neil.brown.name/md
Pull md updates from NeilBrown:
"Mostly fixes, with a few minor features (eg 'last_sync_action' sysfs
file)
A couple marked for -stable including one recent bug which causes a
RAID10 reshape to complete without moving any data :-(
A couple more bugfixes (at least) to come, but haven't confirmed the
right solution yet."
* tag 'md-3.11' of git://neil.brown.name/md:
md/raid10: fix bug which causes all RAID10 reshapes to move no data.
md/raid5: allow 5-device RAID6 to be reshaped to 4-device.
md/raid10: fix two bugs affecting RAID10 reshape.
md: remove doubled description for sync_max, merging it within sync_min/sync_max
MD: Remember the last sync operation that was performed
md: fix buglet in RAID5 -> RAID0 conversion.
md/raid10: check In_sync flag in 'enough()'.
md/raid10: locking changes for 'enough()'.
md: replace strict_strto*() with kstrto*()
md: Wait for md_check_recovery before attempting device removal.
dm-raid: silence compiler warning on rebuilds_per_group.
DM RAID: Fix raid_resume not reviving failed devices in all cases
DM RAID: Break-up untidy function
DM RAID: Add ability to restore transiently failed devices on resume
Linus Torvalds [Thu, 4 Jul 2013 18:25:51 +0000 (11:25 -0700)]
Merge branch 'kconfig-diet' from Dave Hansen
Merge Kconfig menu diet patches from Dave Hansen:
"I think the "Kernel Hacking" menu has gotten a bit out of hand. It is
over 120 lines long on my system with everything enabled and options
are scattered around it haphazardly.
http://sr71.net/~dave/linux/kconfig-horror.png
Let's try to introduce some sanity. This set takes that 120 lines
down to 55 and makes it vastly easier to find some things. It's a
start.
This set stands on its own, but there is plenty of room for follow-up
patches. The arch-specific debug options still end up getting stuck
in the top-level "kernel hacking" menu. OPTIMIZE_INLINING, for
instance, could obviously go in to the "compiler options" menu, but
the fact that it is defined in arch/ in a separate Kconfig file keeps
it on its own for the moment.
The Signed-off-by's in here look funky. I changed employers while
working on this set, so I have signoffs from both email addresses"
* emailed patches from Dave Hansen <dave@sr71.net>:
hang and lockup detection menu
kconfig: consolidate printk options
group locking debugging options
consolidate compilation option configs
consolidate runtime testing configs
order memory debugging Kconfig options
consolidate per-arch stack overflow debugging options
Dave Hansen [Mon, 1 Jul 2013 20:04:50 +0000 (13:04 -0700)]
hang and lockup detection menu
The hard/softlockup and hung-task entries take up 6 lines
of screen real-estate when enabled. I bet folks don't
mess with these _that_ often, so move them in a group
down a level.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Mon, 1 Jul 2013 20:04:49 +0000 (13:04 -0700)]
kconfig: consolidate printk options
Same deal, take the printk-related things and hide them in a menu.
This takes another 4 items out of the top-level menu.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Mon, 1 Jul 2013 20:04:47 +0000 (13:04 -0700)]
group locking debugging options
Original posting:
http://lkml.kernel.org/r/
20121214184208.
D9E5804D@kernel.stglabs.ibm.com
There are quite a few of these, and we want to make sure that
there is one-stop-shopping for lock debugging.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Mon, 1 Jul 2013 20:04:46 +0000 (13:04 -0700)]
consolidate compilation option configs
Original Post:
http://lkml.kernel.org/r/
20121214184207.
6E00DDEC@kernel.stglabs.ibm.com
Again, trying to come up with some common themes of the stuff in
the kernel hacking menu... There are quite a few options to
tweak compilation in some way, or perform extra compile-time
checks. Give them their own menu.
The diff here looks a bit funny... makes it look like I'm
moving debugfs even though I'm actually moving the options on
either side of it.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Mon, 1 Jul 2013 20:04:44 +0000 (13:04 -0700)]
consolidate runtime testing configs
Original posting:
http://lkml.kernel.org/r/
20121214184206.
FC11422F@kernel.stglabs.ibm.com
These runtime tests are great, except that there are a lot of them,
and they are very rarely needed. Give them their own menu so that
only the folks who need them will have to go looking for them.
Note that there are some other runtime tests that are not in here,
like for RCU or locking. This menu should only be used for tests
that do not have a more appropriate home.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Mon, 1 Jul 2013 20:04:43 +0000 (13:04 -0700)]
order memory debugging Kconfig options
Original posting:
http://lkml.kernel.org/r/
20121214184203.
37E6C724@kernel.stglabs.ibm.com
There are a *LOT* of memory debugging options. They are just scattered
all over the "Kernel Hacking" menu. Sure, "memory debugging" is a very
vague term and it's going to be hard to make absolute rules about what
goes in here, but this has to be better than what we had before.
This does, however, leave out the architecture-specific memory
debugging options (like x86's DEBUG_SET_MODULE_RONX). There would need
to be some substantial changes to move those in here. Kconfig can not
easily mix arch-specific and generic options together: it really
requires a file per-architecture, and I think having an
arch/foo/Kconfig.debug-memory might be taking things a bit too far
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Mon, 1 Jul 2013 20:04:42 +0000 (13:04 -0700)]
consolidate per-arch stack overflow debugging options
Original posting:
http://lkml.kernel.org/r/
20121214184202.
F54094D9@kernel.stglabs.ibm.com
Several architectures have similar stack debugging config options.
They all pretty much do the same thing, some with slightly
differing help text.
This patch changes the architectures to instead enable a Kconfig
boolean, and then use that boolean in the generic Kconfig.debug
to present the actual menu option. This removes a bunch of
duplication and adds consistency across arches.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [for tile]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 4 Jul 2013 18:22:55 +0000 (11:22 -0700)]
Merge branch 'hpfs' from Mikulas Patocka
Merge hpfs patches from Mikulas Patocka.
* emailed patches from Mikulas Patocka <mpatocka@artax.karlin.mff.cuni.cz>:
hpfs: implement prefetch to improve performance
hpfs: use mpage
hpfs: better test for errors
Mikulas Patocka [Thu, 4 Jul 2013 17:04:01 +0000 (19:04 +0200)]
hpfs: implement prefetch to improve performance
This patch implements prefetch to improve performance. It helps mostly
when scanning the bitmaps to calculate free space.
Signed-off-by: Mikulas Patocka <mpatocka@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Thu, 4 Jul 2013 16:44:27 +0000 (18:44 +0200)]
hpfs: use mpage
Use the mpage interface to improve performance.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Thu, 4 Jul 2013 16:42:29 +0000 (18:42 +0200)]
hpfs: better test for errors
The test if bitmap access is out of bound could errorneously pass if the
device size is divisible by 16384 sectors and we are asking for one bitmap
after the end.
Check for invalid size in the superblock. Invalid size could cause integer
overflows in the rest of the code.
Signed-off-by: Mikulas Patocka <mpatocka@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 4 Jul 2013 17:29:23 +0000 (10:29 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc changes for the 3.11 merge window. In addition to
the usual bug fixes and small updates, the main highlights are:
- Support for transparent huge pages by Aneesh Kumar for 64-bit
server processors. This allows the use of 16M pages as transparent
huge pages on kernels compiled with a 64K base page size.
- Base VFIO support for KVM on power by Alexey Kardashevskiy
- Wiring up of our nvram to the pstore infrastructure, including
putting compressed oopses in there by Aruna Balakrishnaiah
- Move, rework and improve our "EEH" (basically PCI error handling
and recovery) infrastructure. It is no longer specific to pseries
but is now usable by the new "powernv" platform as well (no
hypervisor) by Gavin Shan.
- I fixed some bugs in our math-emu instruction decoding and made it
usable to emulate some optional FP instructions on processors with
hard FP that lack them (such as fsqrt on Freescale embedded
processors).
- Support for Power8 "Event Based Branch" facility by Michael
Ellerman. This facility allows what is basically "userspace
interrupts" for performance monitor events.
- A bunch of Transactional Memory vs. Signals bug fixes and HW
breakpoint/watchpoint fixes by Michael Neuling.
And more ... I appologize in advance if I've failed to highlight
something that somebody deemed worth it."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
pstore: Add hsize argument in write_buf call of pstore_ftrace_call
powerpc/fsl: add MPIC timer wakeup support
powerpc/mpic: create mpic subsystem object
powerpc/mpic: add global timer support
powerpc/mpic: add irq_set_wake support
powerpc/85xx: enable coreint for all the 64bit boards
powerpc/8xx: Erroneous double irq_eoi() on CPM IRQ in MPC8xx
powerpc/fsl: Enable CONFIG_E1000E in mpc85xx_smp_defconfig
powerpc/mpic: Add get_version API both for internal and external use
powerpc: Handle both new style and old style reserve maps
powerpc/hw_brk: Fix off by one error when validating DAWR region end
powerpc/pseries: Support compression of oops text via pstore
powerpc/pseries: Re-organise the oops compression code
pstore: Pass header size in the pstore write callback
powerpc/powernv: Fix iommu initialization again
powerpc/pseries: Inform the hypervisor we are using EBB regs
powerpc/perf: Add power8 EBB support
powerpc/perf: Core EBB support for 64-bit book3s
powerpc/perf: Drop MMCRA from thread_struct
powerpc/perf: Don't enable if we have zero events
...
Jiri Kosina [Thu, 4 Jul 2013 13:05:02 +0000 (15:05 +0200)]
Merge branches 'for-3.11/wacom-fixed' and 'for-3.11/wiimote' into for-linus
Przemo Firszt [Sat, 29 Jun 2013 09:57:13 +0000 (10:57 +0100)]
HID: wacom: Intuos4 battery charging changes
Intuos4 WL is separately reporting power supply and battery
charging status - now hid-wacom is using that information.
Previously hid-wacom was wrongly treating "battery charging" bit
as "power supply connected". Now it should report battery charging,
battery discharging, battery full and power supply status.
Intuos4 WL sends reports when is in use (obvious) and when unplugging
power supply. If means that if the device is being charged, but it's not
being used it will never report "battery full". The same problem happens
after the device has been connected, but it's not in use - the
battery/ac status will be incorrect. Currently there is no mechanism to
ask the device to send a report containing battery/ac status.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Thu, 4 Jul 2013 13:02:26 +0000 (15:02 +0200)]
Merge branches 'for-3.11/multitouch', 'for-3.11/sony' and 'for-3.11/upstream' into for-linus
Conflicts:
drivers/hid/hid-core.c
Jiri Kosina [Thu, 4 Jul 2013 13:01:01 +0000 (15:01 +0200)]
Merge branches 'for-3.11/battery', 'for-3.11/elo', 'for-3.11/holtek' and 'for-3.11/i2c-hid-fixed' into for-linus
Andrew Duggan [Mon, 17 Jun 2013 23:15:06 +0000 (16:15 -0700)]
HID: i2c-hid: support sending HID output reports using the output register
The current i2c hid driver does not support sending HID output reports using
the output register for devices which support receiving reports through this
method. This patch determines which method to use to send output reports based
on the value of wMaxOutputLength in the device's HID descriptor.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
NeilBrown [Thu, 4 Jul 2013 06:41:53 +0000 (16:41 +1000)]
md/raid10: fix bug which causes all RAID10 reshapes to move no data.
The recent comment:
commit
7e83ccbecd608b971f340e951c9e84cd0343002f
md/raid10: Allow skipping recovery when clean arrays are assembled
Causes raid10 to skip a recovery in certain cases where it is safe to
do so. Unfortunately it also causes a reshape to be skipped which is
never safe. The result is that an attempt to reshape a RAID10 will
appear to complete instantly, but no data will have been moves so the
array will now contain garbage.
(If nothing is written, you can recovery by simple performing the
reverse reshape which will also complete instantly).
Bug was introduced in 3.10, so this is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Cc: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Thu, 4 Jul 2013 06:38:16 +0000 (16:38 +1000)]
md/raid5: allow 5-device RAID6 to be reshaped to 4-device.
There is a bug in 'check_reshape' for raid5.c To checks
that the new minimum number of devices is large enough (which is
good), but it does so also after the reshape has started (bad).
This is bad because
- the calculation is now wrong as mddev->raid_disks has changed
already, and
- it is pointless because it is now too late to stop.
So only perform that test when reshape has not been committed to.
Signed-off-by: NeilBrown <neilb@suse.de>
Linus Torvalds [Thu, 4 Jul 2013 02:56:35 +0000 (19:56 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver to support GMT G762/G763 pwm fan controllers
- add support for DS1631, DS1721, and DS1731 to ds1621 driver
- remove detect function from ds1621 driver as unreliable
- bug fixes in nct6775, iio_hwmon, and adm1021 drivers
- remove redundant platform_set_drvdata in various drivers
- add device tree support to ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Fix temperature rounding operations
hwmon: (nct6775) Drop unsupported fan alarm attributes for NCT6775
hwmon: (nct6775) Fix temperature alarm attributes
Add support for GMT G762/G763 PWM fan controllers
hwmon: (ina2xx) Add device tree support to pass the shunt resistor
hwmon: (ds1621) Update documentation
hwmon: (ds1621) Add DS1731 chip support to ds1621 driver
hwmon: (iio_hwmon) add alias table
hwmon: (adm1021) Do not create min sysfs attributes for LM84
hwmon: (ds1621) Remove detect function
hwmon: (ds1621) Add ds1631 chip support to ds1621 driver and documentation
hwmon: (ds1621) Add ds1721 update interval sysfs attribute
hwmon: (ds1621) Add ds1721 chip support
hwmon: (w83627ehf) Remove redundant platform_set_drvdata()
hwmon: (ntc_thermistor) Remove redundant platform_set_drvdata()
hwmon: (i5k_amb) Remove redundant platform_set_drvdata()
hwmon: (coretemp) Remove redundant platform_set_drvdata()
hwmon: (abituguru3) Remove redundant platform_set_drvdata()
Linus Torvalds [Thu, 4 Jul 2013 02:55:33 +0000 (19:55 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/cooloney/linux-leds
Pull LED subsystem updates from Bryan Wu:
- lp55xx device tree updates
- mc13xxx driver updates
- some clean up
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: mc13783: Fix "uninitialized variable" warning
leds: Convert led class driver from legacy pm ops to dev_pm_ops
leds: leds-mc13783: Add MC13892 LED support
leds: leds-mc13783: Prepare driver to support MC13892 LEDs
leds: renesas-tpu: cleanup a small type issue
leds: use platform_{get,set}_drvdata()
leds: leds-gpio: Let device core handle pinctrl
leds: lp5562: Properly setup of_device_id table
leds: lp5523: Properly setup of_device_id table
leds: lp5521: Properly setup of_device_id table
leds: lp5562: support the device tree feature
leds: lp55xx: support dynamic channel settings in the device tree structure
leds: leds-ns2: remove unnecessary platform_set_drvdata()
leds: leds-mc13783: remove unnecessary platform_set_drvdata()
leds: leds-gpio: remove unnecessary platform_set_drvdata()
leds: atmel-pwm: remove unnecessary platform_set_drvdata()
leds: lp55xx: add support for Device Tree bindings
Linus Torvalds [Thu, 4 Jul 2013 02:52:22 +0000 (19:52 -0700)]
Merge tag 'sound-3.11' of git://git./linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"A relative calm release at this time with a flat diffstat. The only
significant change in the ALSA core side is the support for more than
32 card instances, configurable via kconfig. Other than that, in both
ASoC and other parts, mostly some improvements and fixes on the driver
side.
- hda: More quirks for ALC269-variants on Dell & co, VIA codec fixes
- hda: Haswell HDMI audio fixes, runtime PM improvements
- hda: Intel BayTrail support, ALC5505 DSP support
- es1968: MediaForte M56VAP support
- usb-audio: Improved support for Yamaha/Roland devices
- usb-audio: M2Tech hiFace, Audio Advantage Micro II support
- hdspm: wordclock fixes
- ASoC: Pending fixes for WM8962
- ASoC: Cleanups and fixes for Blackfin, SGTL5000 and UX500
- ASoC: Generalisation of the Bluetooth and HDMI stub drivers
- ASoC: SSM2518 and RT5640 codec drivers.
- ASoC: Tegra CPUs with RT5640 machine driver
- ASoC: AC'97 refactoring bug fixes
- ASoC: ADAU1701 driver fixes
- Clean up of *_set_drvdata() in a wide range of drivers"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (284 commits)
ALSA: vmaster: Fix the regression of missing vmaster hook call
ALSA: hda - Add Dell SSID to support Headset Mic recording
ASoC: adau1701: remove control_data assignment
ASoC: adau1701: more direct regmap usage
ASoC: ac97: fixup multi-platform AC'97 module build failure
ASoC: pxa2xx: fixup multi-platform AC'97 build failures
ASoC: tegra20-ac97: Remove unused variable
ASoC: tegra20-ac97: Remove duplicate error message
ALSA: usb-audio: Add Audio Advantage Micro II
ASoC: tas5086: fix Mid-Z implementation
ASoC: tas5086: fix TAS5086_CLOCK_CONTROL register size
ALSA: Replace the magic number 44 with const
ALSA: hda - Fix the max length of control name in generic parser
ALSA: hda - Guess what, it's two more Dell headset mic quirks
ALSA: hda - Yet another Dell headset mic quirk
ALSA: hda - Add support for ALC5505 DSP power-save mode
ASoC: mfld: Remove unused variable
ALSA: usb-audio: add quirks for Roland QUAD/OCTO-CAPTURE
ALSA: usb-audio: claim autodetected PCM interfaces all at once
ALSA: usb-audio: remove superfluous Roland quirks
...
Linus Torvalds [Thu, 4 Jul 2013 02:49:46 +0000 (19:49 -0700)]
Merge branch 'for-3.11' of git://git./linux/kernel/git/tj/libata
Pull libata updates from Tejun Heo:
"Overview of changes:
- The rest of maintainer email address updates.
- Some core updates - more robust default behavior for port
multipliers, better error reporting for SG_IO commands, and a way
to better work around now ancient and probably pretty rare PATA ->
SATA bridges with ATAPI devices.
- sata_rcar stabilization.
- Some hardware PCI ID additions and one-off low level driver
updates."
* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
AHCI: use ATA_BUSY
libata-zpodd: must use ata_tf_init()
ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDs
ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDs
libata: cleanup SAT error translation
ahci: sata: add support for exynos5440 sata
libata: skip SRST for all SIMG [34]7x port-multipliers
ahci: remove pmp link online check in FBS EH
sata highbank: add bit-banged SGPIO driver support
ahci: make ahci_transmit_led_message into a function pointer
sata_rcar: fix compilation warning in sata_rcar_thaw()
sata_highbank: increase retry count but shorten duration for Calxeda controller
ata: use pci_get_drvdata()
ipr: qc_fill_rtf() method should not store alternate status register
sata_rcar: add 'base' local variable to some functions
sata_rcar: correct 'sata_rcar_sht'
sata_rcar: kill superfluous code in sata_rcar_bmdma_fill_sg()
libata: do not limit R-Car SATA driver to shmobile
ata: use platform_{get,set}_drvdata()
AHCI: Make distinct names for ports in /proc/interrupts
...
Linus Torvalds [Thu, 4 Jul 2013 00:12:13 +0000 (17:12 -0700)]
Merge branch 'akpm' (updates from Andrew Morton)
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
Linus Torvalds [Wed, 3 Jul 2013 23:31:35 +0000 (16:31 -0700)]
Merge tag 'pci-v3.11-changes' of git://git./linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)"
* tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
MAINTAINERS: Add ACPI folks for ACPI-related things under drivers/pci
PCI: Add CircuitCo vendor ID and subsystem ID
PCI: Use pdev->pm_cap instead of pci_find_capability(..,PCI_CAP_ID_PM)
PCI: Return early on allocation failures to unindent mainline code
PCI: Simplify IOV implementation and fix reference count races
PCI: Drop redundant setting of bus->is_added in virtfn_add_bus()
unicore32/PCI: Remove redundant call of pci_bus_add_devices()
m68k/PCI: Remove redundant call of pci_bus_add_devices()
PCI / ACPI / PM: Use correct power state strings in messages
PCI: Fix comment typo for pcie_pme_remove()
PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
PCI: Fix refcount issue in pci_create_root_bus() error recovery path
ia64/PCI: Clean up pci_scan_root_bus() usage
PCI/AER: Reset link for devices below Root Port or Downstream Port
ACPI / APEI: Force fatal AER severity when component has been reset
PCI/AER: Remove "extern" from function declarations
PCI/AER: Move AER severity defines to aer.h
PCI/AER: Set dev->__aer_firmware_first only for matching devices
PCI/AER: Factor out HEST device type matching
PCI/AER: Don't parse HEST table for non-PCIe devices
...
Andrew Morton [Wed, 3 Jul 2013 22:09:23 +0000 (15:09 -0700)]
tools/testing/selftests: don't assume the x bit is set on scripts
The x bit can easily get lost (patch(1) loses it, for example).
Reported-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ramkumar Ramachandra [Wed, 3 Jul 2013 22:09:22 +0000 (15:09 -0700)]
selftests: add .gitignore for kcmp
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ramkumar Ramachandra [Wed, 3 Jul 2013 22:09:21 +0000 (15:09 -0700)]
selftests: fix clean target in kcmp Makefile
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ramkumar Ramachandra [Wed, 3 Jul 2013 22:09:20 +0000 (15:09 -0700)]
selftests: add .gitignore for vm
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joern Engel [Wed, 3 Jul 2013 22:09:19 +0000 (15:09 -0700)]
selftests: add hugetlbfstest
As the confusing naming indicates, this test has some overlap with
pre-existing tests. Would be nice to merge them eventually. But since it
is only test code, cleanliness is much less important than mere existence.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joern Engel [Wed, 3 Jul 2013 22:09:18 +0000 (15:09 -0700)]
self-test: fix make clean
thuge-gen was forgotten. Fix it by removing the duplication, so we don't
get too many repeats.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joern Engel [Wed, 3 Jul 2013 22:09:17 +0000 (15:09 -0700)]
selftests: exit 1 on failure
In case this ever gets scripted, it should return 0 on success and 1 on
failure. Parsing the output should be left to meatbags.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kevin Hao [Wed, 3 Jul 2013 22:09:16 +0000 (15:09 -0700)]
kernel/resource.c: remove the unneeded assignment in function __find_resource
This line was introduced by
fcb11918 ("resources: add arch hook for
preventing allocation in reserved areas"). But the struct tmp was already
assigned to *new in the above line, so this seems superfluous. Just
remove it.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tang Chen [Wed, 3 Jul 2013 22:09:16 +0000 (15:09 -0700)]
aio: fix wrong comment in aio_complete()
ctx->ctx_lock should be ctx->completion_lock.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean-Francois Dagenais [Wed, 3 Jul 2013 22:09:15 +0000 (15:09 -0700)]
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
Power-up timing
The DS2408 is sensitive to the power-on slew rate and can inadvertently
power up with a test mode feature enabled. When this occurs, the P0 port
does not respond to the Channel Access Write command. For most reliable
operation, it is recommended to disable the test mode after every power-on
reset using the Disable Test Mode sequence shown below. The 64-bit ROM
code must be transmitted in the same bit sequence as with the Match ROM
command, i.e., least significant bit first. This precaution is
recommended in parasite power mode (VCC pin connected to GND) as well as
with VCC power.
Disable Test Mode:
RST,PD,96h,<64-bit DS2408 ROM Code>,3Ch,RST,PD
[akpm@linux-foundation.org: don't use kerenldoc token to introduce a non-kerneldoc comment, tweak whitespace]
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Libo Chen [Wed, 3 Jul 2013 22:09:14 +0000 (15:09 -0700)]
drivers/memstick/host/r592.c: convert to module_pci_driver
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Libo Chen [Wed, 3 Jul 2013 22:09:13 +0000 (15:09 -0700)]
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
Use module_pci_driver instead of init/exit, make code clean.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Luebbe [Wed, 3 Jul 2013 22:09:12 +0000 (15:09 -0700)]
pps-gpio: add device-tree binding and support
Instead of allocating a struct pps_gpio_platform_data in the DT case,
store the necessary information in struct pps_gpio_device_data itself.
This avoids an additional allocation and the ifdef. It also gets rid of
some indirection.
Also use dev_err instead of pr_err in the changed code.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Luebbe [Wed, 3 Jul 2013 22:09:10 +0000 (15:09 -0700)]
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
This removes some boilerplate code (no functional changes).
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Luebbe [Wed, 3 Jul 2013 22:09:10 +0000 (15:09 -0700)]
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandru Gheorghiu [Wed, 3 Jul 2013 22:09:09 +0000 (15:09 -0700)]
drivers/parport/share.c: use kzalloc
Replaced calls to kmalloc and memset with kzalloc.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kees Cook [Wed, 3 Jul 2013 22:09:08 +0000 (15:09 -0700)]
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
Avoid strncpy anti-pattern.
[akpm@linux-foundation.org: remove the str[cpy|dup] altogether]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ed Cashin [Wed, 3 Jul 2013 22:09:07 +0000 (15:09 -0700)]
aoe: update internal version number to v83
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ed Cashin [Wed, 3 Jul 2013 22:09:06 +0000 (15:09 -0700)]
aoe: update copyright date
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ed Cashin [Wed, 3 Jul 2013 22:09:05 +0000 (15:09 -0700)]
aoe: perform I/O completions in parallel
Some users have a large AoE target while others like to use many AoE
targets at the same time. In the latter case, there is an opportunity to
greatly improve aggregate throughput by allowing different threads to
complete the I/O associated with each target. For 36 targets, 4 KiB read
throughput roughly doubles, for example, with these changes in place.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Clements [Wed, 3 Jul 2013 22:09:04 +0000 (15:09 -0700)]
nbd: correct disconnect behavior
Currently, when a disconnect is requested by the user (via NBD_DISCONNECT
ioctl) the return from NBD_DO_IT is undefined (it is usually one of
several error codes). This means that nbd-client does not know if a
manual disconnect was performed or whether a network error occurred.
Because of this, nbd-client's persist mode (which tries to reconnect after
error, but not after manual disconnect) does not always work correctly.
This change fixes this by causing NBD_DO_IT to always return 0 if a user
requests a disconnect. This means that nbd-client can correctly either
persist the connection (if an error occurred) or disconnect (if the user
requested it).
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Acked-by: Rob Landley <rob@landley.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Belczyk [Wed, 3 Jul 2013 22:09:03 +0000 (15:09 -0700)]
nbd: remove bogus BUG_ON in NBD_CLEAR_QUE
The NBD_CLEAR_QUE ioctl has been deprecated for quite some time (its job
is now done by two other ioctls). We should stop trying to make bogus
assertions in it. Also, user-level code should remove calls to
NBD_CLEAR_QUE, ASAP.
Signed-off-by: Michal Belczyk <belczyk@bsd.krakow.pl>
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Raphael S. Carvalho [Wed, 3 Jul 2013 22:09:02 +0000 (15:09 -0700)]
kernel/pid.c: move statement
Move statement to static initilization of init_pid_ns.
Signed-off-by: Raphael S. Carvalho <raphael.scarv@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Wed, 3 Jul 2013 22:09:01 +0000 (15:09 -0700)]
rapidio: change endpoint device name format
Change endpoint device name format to use a component tag value instead of
device destination ID.
RapidIO specification defines a component tag to be a unique identifier
for devices in a network. RapidIO switches already use component tag as
part of their device name and also use it for device identification when
processing error management event notifications.
Forming an endpoint's device name using its component tag instead of
destination ID allows to keep sysfs device directories unchanged in case
if a routing process dynamically changes endpoint's destination ID as a
result of route optimization.
This change should not affect any existing users because a valid device
destination ID always should be obtained by reading "destid" attribute and
not by parsing device name.
This patch also removes switchid member from struct rio_switch because it
simply duplicates the component tag and does not have other use than in
device name generation.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Wed, 3 Jul 2013 22:08:59 +0000 (15:08 -0700)]
rapidio: documentation update
Update RapidIO documentation files to reflect modularization changes.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Wed, 3 Jul 2013 22:08:58 +0000 (15:08 -0700)]
rapidio: add udev notification
Add RapidIO-specific modalias generation to enable udev notifications
about RapidIO-specific events.
The RapidIO modalias string format is shown below:
"rapidio:vNNNNdNNNNavNNNNadNNNN"
Where:
v - Device Vendor ID (16 bit),
d - Device ID (16 bit),
av - Assembly Vendor ID (16 bit),
ad - Assembly ID (16 bit),
as they are reported in corresponding Capability Registers (CARs)
of each RapidIO device.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Wed, 3 Jul 2013 22:08:56 +0000 (15:08 -0700)]
rapidio: add modular build option for the subsystem core
Add a configuration option to build RapidIO subsystem core code as a
loadable kernel module. Currently this option is available only for
x86-based platforms, with the additional patch for PowerPC planned to be
provided later.
This patch replaces kernel command line parameter "riohdid=" with its
module-specific analog "rapidio.hdid=".
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Wed, 3 Jul 2013 22:08:55 +0000 (15:08 -0700)]
rapidio/tsi721: convert to modular mport driver
This patch adds an option to build device driver for Tsi721 PCIe-to-SRIO
bridge device as a kernel module.
Currently this module cannot be unloaded because the existing RapidIO
subsystem code does not support dynamic removal of local RapidIO
controllers (TODO).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Wed, 3 Jul 2013 22:08:53 +0000 (15:08 -0700)]
rapidio: update enumerator registration mechanism
Update enumeration/discovery method registration mechanism to allow
loading enumeration/discovery methods before all mports are registered.
Existing statically linked RapidIO subsystem expects that all available
RapidIO mport devices are initialized and registered before the
enumeration/discovery method is registered. Switching to loadable mport
device drivers creates situation when mport device driver can be loaded
after enumeration/discovery method is attached (e.g., loadable mport
driver in a system with statically linked RapidIO core and enumerator).
This also will happen in a system with hot-pluggable RapidIO controllers.
To remove the dependency on the initialization/registration order this
patch introduces enumeration/discovery registration mechanism that
supports arbitrary registration order of mports and enumerator/discovery
methods.
The following registration rules are implemented:
- only one enumeration/discovery method can be registered for given mport ID
(including RIO_MPORT_ANY);
- when new enumeration/discovery methods tries to attach to the registered mport
device, method with matching mport ID will replace a default method previously
registered for given mport (if any);
- enumeration/discovery method with target ID=RIO_MPORT_ANY will be attached
only to mports that do not have another enumerator attached to them;
- when new mport device is registered with RapidIO subsystem, registration
routine searches for the enumeration/discovery method with the best matching
mport ID;
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Wed, 3 Jul 2013 22:08:52 +0000 (15:08 -0700)]
rapidio/rionet: rework driver initialization and removal
Rework probe/remove routines to prevent rionet driver from monopolizing
target RapidIO devices. Fix conflict with modular RapidIO switch drivers.
Using one of RapidIO messaging channels rionet driver provides a service
layer common to all endpoint devices in a system's RapidIO network. These
devices may also require their own specific device driver which will be
blocked from attaching to the target device by rionet (or block rionet if
loaded earlier). To avoid conflict with device-specific drivers, the
rionet driver is reworked to be registered as a subsystem interface on the
RapidIO bus.
The reworked rio_remove_dev() and rionet_exit() routines also include
handling of individual rionet peer device removal which was not supported
before.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Wed, 3 Jul 2013 22:08:50 +0000 (15:08 -0700)]
rapidio: convert switch drivers to modules
Rework RapidIO switch drivers to add an option to build them as loadable
kernel modules.
This patch removes RapidIO-specific vmlinux section and converts switch
drivers to be compatible with LDM driver registration method. To simplify
registration of device-specific callback routines this patch introduces
rio_switch_ops data structure. The sw_sysfs() callback is removed from
the list of device-specific operations because under the new structure its
functions can be handled by switch driver's probe() and remove() routines.
If a specific switch device driver is not loaded the RapidIO subsystem
core will use default standard-based operations to configure a switch.
Because the current implementation of RapidIO enumeration/discovery method
relies on availability of device-specific operations for error management,
switch device drivers must be loaded before the RapidIO
enumeration/discovery starts.
This patch also moves several common routines from enumeration/discovery
module into the RapidIO core code to make switch-specific operations
accessible to all components of RapidIO subsystem.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wu Fengguang [Wed, 3 Jul 2013 22:08:49 +0000 (15:08 -0700)]
drivers/rapidio/rio-scan.c: make functions static
sparse warnings:
drivers/rapidio/rio-scan.c:1143:5: sparse: symbol 'rio_enum_mport' was not declared. Should it be static?
drivers/rapidio/rio-scan.c:1246:5: sparse: symbol 'rio_disc_mport' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: "Bounine, Alexandre" <Alexandre.Bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Wed, 3 Jul 2013 22:08:48 +0000 (15:08 -0700)]
rapidio/switches: remove tsi500 driver
Remove the driver for Tsi500 Parallel RapidIO switch because this device
has not been available for several years. Since the first introduction of
Tsi500, the parallel RapidIO interface was replaced by the serial RapidIO
(sRIO) and therefore there is no value in keeping this driver.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean Delvare [Wed, 3 Jul 2013 22:08:47 +0000 (15:08 -0700)]
idr: print a stack dump after ida_remove warning
We print a dump stack after idr_remove warning. This is useful to find
the faulty piece of code. Let's do the same for ida_remove, as it would
be equally useful there.
[akpm@linux-foundation.org: convert the open-coded printk+dump_stack into WARN()]
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhang Yanfei [Wed, 3 Jul 2013 22:08:45 +0000 (15:08 -0700)]
s390: remove setting for saved_max_pfn
The only user of saved_max_pfn in s390 is read_oldmem interface but we
have removed that interface, so saved_max_pfn is now unneeded in s390, and
we needn't set it anymore.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhang Yanfei [Wed, 3 Jul 2013 22:08:44 +0000 (15:08 -0700)]
ia64: remove setting for saved_max_pfn
The only user of saved_max_pfn in ia64 is read_oldmem interface but we
have removed that interface, so saved_max_pfn is now unneeded in ia64, and
we needn't set it anymore.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhang Yanfei [Wed, 3 Jul 2013 22:08:42 +0000 (15:08 -0700)]
powerpc: Remove savemaxmem parameter setup
saved_max_pfn is used to know the amount of memory that the previous
kernel used. And for powerpc, we set saved_max_pfn by passing the kernel
commandline parameter "savemaxmem=".
The only user of saved_max_pfn in powerpc is read_oldmem interface. Since
we have removed read_oldmem, we don't need this parameter anymore.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhang Yanfei [Wed, 3 Jul 2013 22:08:40 +0000 (15:08 -0700)]
mips: remove savemaxmem parameter setup
saved_max_pfn is used to know the amount of memory that the previous
kernel used. And for powerpc, we set saved_max_pfn by passing the kernel
commandline parameter "savemaxmem=".
The only user of saved_max_pfn in mips is read_oldmem interface. Since we
have removed read_oldmem, so we don't need this parameter anymore.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhang Yanfei [Wed, 3 Jul 2013 22:08:38 +0000 (15:08 -0700)]
Documentation/kdump/kdump.txt: remove /dev/oldmem description
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhang Yanfei [Wed, 3 Jul 2013 22:08:36 +0000 (15:08 -0700)]
/dev/oldmem: Remove the interface
/dev/oldmem provides the interface for us to access the "old memory" in
the dump-capture kernel. Unfortunately, no one actually uses this
interface.
And this interface could actually cause some real problems if used on ia64
where the cached/uncached accesses are mixed. See the discussion from the
link: https://lkml.org/lkml/2013/4/12/386.
So Eric suggested that we should remove /dev/oldmem as an unused piece of
code.
[akpm@linux-foundation.org: mention /dev/oldmem obsolescence in devices.txt]
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:35 +0000 (15:08 -0700)]
fs/exec.c:de_thread: mt-exec should update ->real_start_time
924b42d5 ("Use boot based time for process start time and boot time in
/proc") updated copy_process/do_task_stat but forgot about de_thread().
This breaks "ps axOT" if a sub-thread execs.
Note: I think that task->start_time should die.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Tomas Janousek <tjanouse@redhat.com>
Cc: Tomas Smetana <tsmetana@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:34 +0000 (15:08 -0700)]
fs/exec.c: do_execve_common(): use current_user()
Trivial cleanup. do_execve_common() can use current_user() and avoid the
unnecessary "struct cred *cred" var.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:32 +0000 (15:08 -0700)]
kernel/fork.c:copy_process(): consolidate the lockless CLONE_THREAD checks
copy_process() does a lot of "chaotic" initializations and checks
CLONE_THREAD twice before it takes tasklist. In particular it sets
"p->group_leader = p" and then changes it again under tasklist if
!thread_group_leader(p).
This looks a bit confusing, lets create a single "if (CLONE_THREAD)" block
which initializes ->exit_signal, ->group_leader, and ->tgid.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:31 +0000 (15:08 -0700)]
kernel/fork.c:copy_process(): don't add the uninitialized child to thread/task/pid lists
copy_process() adds the new child to thread_group/init_task.tasks list and
then does attach_pid(child, PIDTYPE_PID). This means that the lockless
next_thread() or next_task() can see this thread with the wrong pid. Say,
"ls /proc/pid/task" can list the same inode twice.
We could move attach_pid(child, PIDTYPE_PID) up, but in this case
find_task_by_vpid() can find the new thread before it was fully
initialized.
And this is already true for PIDTYPE_PGID/PIDTYPE_SID, With this patch
copy_process() initializes child->pids[*].pid first, then calls
attach_pid() to insert the task into the pid->tasks list.
attach_pid() no longer need the "struct pid*" argument, it is always
called after pid_link->pid was already set.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:30 +0000 (15:08 -0700)]
kernel/fork.c:copy_process(): unify CLONE_THREAD-or-thread_group_leader code
Cleanup and preparation for the next changes.
Move the "if (clone_flags & CLONE_THREAD)" code down under "if
(likely(p->pid))" and turn it into into the "else" branch. This makes the
process/thread initialization more symmetrical and removes one check.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Paris [Wed, 3 Jul 2013 22:08:29 +0000 (15:08 -0700)]
fork: reorder permissions when violating number of processes limits
When a task is attempting to violate the RLIMIT_NPROC limit we have a
check to see if the task is sufficiently priviledged. The check first
looks at CAP_SYS_ADMIN, then CAP_SYS_RESOURCE, then if the task is uid=0.
A result is that tasks which are allowed by the uid=0 check are first
checked against the security subsystem. This results in the security
subsystem auditting a denial for sys_admin and sys_resource and then the
task passing the uid=0 check.
This patch rearranges the code to first check uid=0, since if we pass that
we shouldn't hit the security system at all. We then check sys_resource,
since it is the smallest capability which will solve the problem. Lastly
we check the fallback everything cap_sysadmin. We don't want to give this
capability many places since it is so powerful.
This will eliminate many of the false positive/needless denial messages we
get when a root task tries to violate the nproc limit. (note that
kthreads count against root, so on a sufficiently large machine we can
actually get past the default limits before any userspace tasks are
launched.)
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhao Hongjiang [Wed, 3 Jul 2013 22:08:28 +0000 (15:08 -0700)]
fs/proc/kcore.c: using strlcpy() instead of strncpy()
For NUL terminated string, set '\0' at the end.
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:27 +0000 (15:08 -0700)]
fs/proc/uptime.c:uptime_proc_show(): use get_monotonic_boottime()
Change uptime_proc_show() to use get_monotonic_boottime() instead of
do_posix_clock_monotonic_gettime() + monotonic_to_bootbased().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Tomas Janousek <tjanouse@redhat.com>
Cc: Tomas Smetana <tsmetana@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:26 +0000 (15:08 -0700)]
exit.c: unexport __set_special_pids()
Move __set_special_pids() from exit.c to sys.c close to its single caller
and make it static.
And rename it to set_special_pids(), another helper with this name has
gone away.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:25 +0000 (15:08 -0700)]
fs/exec.c:de_thread(): use change_pid() rather than detach_pid/attach_pid
de_thread() can use change_pid() instead of detach + attach. This looks
better and this ensures that, say, next_thread() can never see a task with
->pid == NULL.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Sergey Dyasly <dserrg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:23 +0000 (15:08 -0700)]
coredump: '% at the end' shouldn't bypass core_uses_pid logic
"goto end" should not bypass the "Backward compatibility with
core_uses_pid" code, move this label up.
While at it,
- It is ugly to copy '|' into cn->corename and then inc
the pointer for argv_split().
Change format_corename() to increment pat_ptr instead.
- Remove the dead "if (*pat_ptr == 0)" in format_corename(),
we already checked it is not zero.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:22 +0000 (15:08 -0700)]
coredump: kill call_count, add core_name_size
Imho, "atomic_t call_count" is ugly and should die. It buys nothing and
in fact it can grow more than necessary, expand doesn't check if it was
already incremented by another task.
Kill it, and introduce "static int core_name_size" updated by
expand_corename(). This is obviously racy too but harmless, and
core_name_size never grows for no reason.
We do not bother to to calculate the "right" new size, we simply do
kmalloc(size_we_need) and use ksize() to rely on kmalloc_index's decision.
Finally change format_corename() to use expand_corename(), krealloc(NULL)
is fine.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:20 +0000 (15:08 -0700)]
coredump: kill cn_escape(), introduce cn_esc_printf()
The usage of cn_escape() looks really annoying, imho this sequence needs a
wrapper. And it is buggy. If cn_printf() does expand_corename()
cn_escape() writes to the freed memory.
Introduce cn_esc_printf() which hopefully does this all right. It records
the index before cn_vprintf(), not "char *" which is no longer valid (in
general) after krealloc().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:19 +0000 (15:08 -0700)]
coredump: cn_vprintf() has no reason to call vsnprintf() twice
cn_vprintf() looks really overcomplicated and sub-optimal. We do not need
vsnprintf(NULL) to calculate the size we need, we can simply try to print
into the current buffer and expand/retry only if necessary.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:17 +0000 (15:08 -0700)]
coredump: introduce cn_vprintf()
Turn cn_printf(...) into cn_vprintf(va_list args), reintroduce
cn_printf() as a trivial wrapper.
This simplifies the next change and cn_vprintf() will have more
callers.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:16 +0000 (15:08 -0700)]
coredump: format_corename() can leak cn->corename
do_coredump() assumes that format_corename() can only fail if
expand_corename() fails and frees cn->corename. This is not true, for
example cn_print_exe_file() can fail and in this case nobody frees
cn->corename.
Change do_coredump() to always do kfree(cn->corename) after it calls
format_corename() (NULL is fine), change expand_corename() to do nothing
if kmalloc() fails.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Colin Walters <walters@verbum.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:15 +0000 (15:08 -0700)]
usermodehelper: kill the sub_info->path[0] check
call_usermodehelper_exec() does nothing but returns success if path[0] ==
0. The only user which needs this strange feature is request_module(), it
can check modprobe_path[0] itself like other users do if they want to
detect the "disabled by admin" case.
Kill it. Not only it looks strange, it can confuse other callers. And
this allows us to revert
264b83c0 ("usermodehelper: check
subprocess_info->path != NULL"), do_execve(NULL) is safe.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:14 +0000 (15:08 -0700)]
signals: eventpoll: do not use sigprocmask()
sigprocmask() should die. None of the current callers actually
need this strange interface.
Change fs/eventpoll.c to use set_current_blocked(). This also
means we should not worry about SIGKILL/SIGSTOP.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Eric Wong <normalperson@yhbt.net>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Vagin [Wed, 3 Jul 2013 22:08:12 +0000 (15:08 -0700)]
ptrace: add ability to get/set signal-blocked mask
crtools uses a parasite code for dumping processes. The parasite code is
injected into a process with help PTRACE_SEIZE.
Currently crtools blocks signals from a parasite code. If a process has
pending signals, crtools wait while a process handles these signals.
This method is not suitable for stopped tasks. A stopped task can have a
few pending signals, when we will try to execute a parasite code, we will
need to drop SIGSTOP, but all other signals must remain pending, because a
state of processes must not be changed during checkpointing.
This patch adds two ptrace commands to set/get signal-blocked mask.
I think gdb can use this commands too.
[akpm@linux-foundation.org: be consistent with brace layout]
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Wed, 3 Jul 2013 22:08:11 +0000 (15:08 -0700)]
x86: kill TIF_DEBUG
Because it is not used.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Wed, 3 Jul 2013 22:08:10 +0000 (15:08 -0700)]
docbook: add futexes to kernel-locking docbook
Add Fast User Mutexes (futexes) to kernel-locking docbook.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>