OSDN Git Service
Olof Johansson [Wed, 21 Nov 2012 21:56:36 +0000 (13:56 -0800)]
Merge tag 'omap-for-v3.7-rc5/fixes-signed' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more regression fixes related to u-boot only muxing
essential pins.
* tag 'omap-for-v3.7-rc5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
ARM: OMAP: Add maintainer entry for IGEP machines
Olof Johansson [Mon, 19 Nov 2012 16:48:42 +0000 (08:48 -0800)]
Merge tag 'davinci-fixes-for-v3.7' of git://gitorious.org/linux-davinci/linux-davinci into fixes
From Sekhar Nori:
Fixes an "signal out of range" error when using enhanced
definition display with a DaVinci DM644x device.
* tag 'davinci-fixes-for-v3.7' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: dm644x: fix out range signal for ED
Lad, Prabhakar [Wed, 3 Oct 2012 06:35:00 +0000 (12:05 +0530)]
ARM: davinci: dm644x: fix out range signal for ED
Fix the video clock setting when custom timings are used with
pclock <= 27MHz. Existing video clock selection uses PLL2 mode
which results in a 54MHz clock whereas using the MXI mode results
in a 27MHz clock (which is the one actually desired).
This bug affects the Enhanced Definition (ED) support on DM644x.
Without this patch, out-range signals errors are were observed on
the TV when viewing ED. An out-of-range signal is often caused when
the field rate is above the rate that the television will handle.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
[nsekhar@ti.com: reword commit message based on on-list discussion]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Linus Torvalds [Sat, 17 Nov 2012 01:42:40 +0000 (17:42 -0800)]
Linux 3.7-rc6
Linus Torvalds [Sat, 17 Nov 2012 00:49:10 +0000 (16:49 -0800)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fix from Marcelo Tosatti:
"A correction for oops on module init with older Intel hosts."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix invalid secondary exec controls in vmx_cpuid_update()
Linus Torvalds [Fri, 16 Nov 2012 23:26:38 +0000 (15:26 -0800)]
Merge branch 'akpm' (Fixes from Andrew)
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (12 patches)
revert "mm: fix-up zone present pages"
tmpfs: change final i_blocks BUG to WARNING
tmpfs: fix shmem_getpage_gfp() VM_BUG_ON
mm: highmem: don't treat PKMAP_ADDR(LAST_PKMAP) as a highmem address
mm: revert "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures"
rapidio: fix kernel-doc warnings
swapfile: fix name leak in swapoff
memcg: fix hotplugged memory zone oops
mips, arc: fix build failure
memcg: oom: fix totalpages calculation for memory.swappiness==0
mm: fix build warning for uninitialized value
mm: add anon_vma_lock to validate_mm()
Andrew Morton [Fri, 16 Nov 2012 22:15:06 +0000 (14:15 -0800)]
revert "mm: fix-up zone present pages"
Revert commit
7f1290f2f2a4 ("mm: fix-up zone present pages")
That patch tried to fix a issue when calculating zone->present_pages,
but it caused a regression on 32bit systems with HIGHMEM. With that
change, reset_zone_present_pages() resets all zone->present_pages to
zero, and fixup_zone_present_pages() is called to recalculate
zone->present_pages when the boot allocator frees core memory pages into
buddy allocator. Because highmem pages are not freed by bootmem
allocator, all highmem zones' present_pages becomes zero.
Various options for improving the situation are being discussed but for
now, let's return to the 3.6 code.
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: David Rientjes <rientjes@google.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Fri, 16 Nov 2012 22:15:04 +0000 (14:15 -0800)]
tmpfs: change final i_blocks BUG to WARNING
Under a particular load on one machine, I have hit shmem_evict_inode()'s
BUG_ON(inode->i_blocks), enough times to narrow it down to a particular
race between swapout and eviction.
It comes from the "if (freed > 0)" asymmetry in shmem_recalc_inode(),
and the lack of coherent locking between mapping's nrpages and shmem's
swapped count. There's a window in shmem_writepage(), between lowering
nrpages in shmem_delete_from_page_cache() and then raising swapped
count, when the freed count appears to be +1 when it should be 0, and
then the asymmetry stops it from being corrected with -1 before hitting
the BUG.
One answer is coherent locking: using tree_lock throughout, without
info->lock; reasonable, but the raw_spin_lock in percpu_counter_add() on
used_blocks makes that messier than expected. Another answer may be a
further effort to eliminate the weird shmem_recalc_inode() altogether,
but previous attempts at that failed.
So far undecided, but for now change the BUG_ON to WARN_ON: in usual
circumstances it remains a useful consistency check.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Fri, 16 Nov 2012 22:15:03 +0000 (14:15 -0800)]
tmpfs: fix shmem_getpage_gfp() VM_BUG_ON
Fuzzing with trinity hit the "impossible" VM_BUG_ON(error) (which Fedora
has converted to WARNING) in shmem_getpage_gfp():
WARNING: at mm/shmem.c:1151 shmem_getpage_gfp+0xa5c/0xa70()
Pid: 29795, comm: trinity-child4 Not tainted 3.7.0-rc2+ #49
Call Trace:
warn_slowpath_common+0x7f/0xc0
warn_slowpath_null+0x1a/0x20
shmem_getpage_gfp+0xa5c/0xa70
shmem_fault+0x4f/0xa0
__do_fault+0x71/0x5c0
handle_pte_fault+0x97/0xae0
handle_mm_fault+0x289/0x350
__do_page_fault+0x18e/0x530
do_page_fault+0x2b/0x50
page_fault+0x28/0x30
tracesys+0xe1/0xe6
Thanks to Johannes for pointing to truncation: free_swap_and_cache()
only does a trylock on the page, so the page lock we've held since
before confirming swap is not enough to protect against truncation.
What cleanup is needed in this case? Just delete_from_swap_cache(),
which takes care of the memcg uncharge.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Dave Jones <davej@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Fri, 16 Nov 2012 22:15:00 +0000 (14:15 -0800)]
mm: highmem: don't treat PKMAP_ADDR(LAST_PKMAP) as a highmem address
kmap_to_page returns the corresponding struct page for a virtual address
of an arbitrary mapping. This works by checking whether the address
falls in the pkmap region and using the pkmap page tables instead of the
linear mapping if appropriate.
Unfortunately, the bounds checking means that PKMAP_ADDR(LAST_PKMAP) is
incorrectly treated as a highmem address and we can end up walking off
the end of pkmap_page_table and subsequently passing junk to pte_page.
This patch fixes the bound check to stay within the pkmap tables.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Fri, 16 Nov 2012 22:14:59 +0000 (14:14 -0800)]
mm: revert "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures"
Jiri Slaby reported the following:
(It's an effective revert of "mm: vmscan: scale number of pages
reclaimed by reclaim/compaction based on failures".) Given kswapd
had hours of runtime in ps/top output yesterday in the morning
and after the revert it's now 2 minutes in sum for the last 24h,
I would say, it's gone.
The intention of the patch in question was to compensate for the loss of
lumpy reclaim. Part of the reason lumpy reclaim worked is because it
aggressively reclaimed pages and this patch was meant to be a sane
compromise.
When compaction fails, it gets deferred and both compaction and
reclaim/compaction is deferred avoid excessive reclaim. However, since
commit
c654345924f7 ("mm: remove __GFP_NO_KSWAPD"), kswapd is woken up
each time and continues reclaiming which was not taken into account when
the patch was developed.
Attempts to address the problem ended up just changing the shape of the
problem instead of fixing it. The release window gets closer and while
a THP allocation failing is not a major problem, kswapd chewing up a lot
of CPU is.
This patch reverts commit
83fde0f22872 ("mm: vmscan: scale number of
pages reclaimed by reclaim/compaction based on failures") and will be
revisited in the future.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Zdenek Kabelac <zkabelac@redhat.com>
Tested-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 16 Nov 2012 22:14:56 +0000 (14:14 -0800)]
rapidio: fix kernel-doc warnings
Fix rapidio kernel-doc warnings:
Warning(drivers/rapidio/rio.c:415): No description found for parameter 'local'
Warning(drivers/rapidio/rio.c:415): Excess function parameter 'lstart' description in 'rio_map_inb_region'
Warning(include/linux/rio.h:290): No description found for parameter 'switches'
Warning(include/linux/rio.h:290): No description found for parameter 'destid_table'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xiaotian Feng [Fri, 16 Nov 2012 22:14:55 +0000 (14:14 -0800)]
swapfile: fix name leak in swapoff
There's a name leak introduced by commit
91a27b2a7567 ("vfs: define
struct filename and have getname() return it"). Add the missing
putname.
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Fri, 16 Nov 2012 22:14:54 +0000 (14:14 -0800)]
memcg: fix hotplugged memory zone oops
When MEMCG is configured on (even when it's disabled by boot option),
when adding or removing a page to/from its lru list, the zone pointer
used for stats updates is nowadays taken from the struct lruvec. (On
many configurations, calculating zone from page is slower.)
But we have no code to update all the lruvecs (per zone, per memcg) when
a memory node is hotadded. Here's an extract from the oops which
results when running numactl to bind a program to a newly onlined node:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000f60
IP: __mod_zone_page_state+0x9/0x60
Pid: 1219, comm: numactl Not tainted 3.6.0-rc5+ #180 Bochs Bochs
Process numactl (pid: 1219, threadinfo
ffff880039abc000, task
ffff8800383c4ce0)
Call Trace:
__pagevec_lru_add_fn+0xdf/0x140
pagevec_lru_move_fn+0xb1/0x100
__pagevec_lru_add+0x1c/0x30
lru_add_drain_cpu+0xa3/0x130
lru_add_drain+0x2f/0x40
...
The natural solution might be to use a memcg callback whenever memory is
hotadded; but that solution has not been scoped out, and it happens that
we do have an easy location at which to update lruvec->zone. The lruvec
pointer is discovered either by mem_cgroup_zone_lruvec() or by
mem_cgroup_page_lruvec(), and both of those do know the right zone.
So check and set lruvec->zone in those; and remove the inadequate
attempt to set lruvec->zone from lruvec_init(), which is called before
NODE_DATA(node) has been allocated in such cases.
Ah, there was one exceptionr. For no particularly good reason,
mem_cgroup_force_empty_list() has its own code for deciding lruvec.
Change it to use the standard mem_cgroup_zone_lruvec() and
mem_cgroup_get_lru_size() too. In fact it was already safe against such
an oops (the lru lists in danger could only be empty), but we're better
proofed against future changes this way.
I've marked this for stable (3.6) since we introduced the problem in 3.5
(now closed to stable); but I have no idea if this is the only fix
needed to get memory hotadd working with memcg in 3.6, and received no
answer when I enquired twice before.
Reported-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Fri, 16 Nov 2012 22:14:52 +0000 (14:14 -0800)]
mips, arc: fix build failure
Using a cross-compiler to fix another issue, the following build error
occurred for mips defconfig:
arch/mips/fw/arc/misc.c: In function 'ArcHalt':
arch/mips/fw/arc/misc.c:25:2: error: implicit declaration of function 'local_irq_disable'
Fix it up by including irqflags.h.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 16 Nov 2012 22:14:49 +0000 (14:14 -0800)]
memcg: oom: fix totalpages calculation for memory.swappiness==0
oom_badness() takes a totalpages argument which says how many pages are
available and it uses it as a base for the score calculation. The value
is calculated by mem_cgroup_get_limit which considers both limit and
total_swap_pages (resp. memsw portion of it).
This is usually correct but since
fe35004fbf9e ("mm: avoid swapping out
with swappiness==0") we do not swap when swappiness is 0 which means
that we cannot really use up all the totalpages pages. This in turn
confuses oom score calculation if the memcg limit is much smaller than
the available swap because the used memory (capped by the limit) is
negligible comparing to totalpages so the resulting score is too small
if adj!=0 (typically task with CAP_SYS_ADMIN or non zero oom_score_adj).
A wrong process might be selected as result.
The problem can be worked around by checking mem_cgroup_swappiness==0
and not considering swap at all in such a case.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Fri, 16 Nov 2012 22:14:48 +0000 (14:14 -0800)]
mm: fix build warning for uninitialized value
do_wp_page() sets mmun_called if mmun_start and mmun_end were
initialized and, if so, may call mmu_notifier_invalidate_range_end()
with these values. This doesn't prevent gcc from emitting a build
warning though:
mm/memory.c: In function `do_wp_page':
mm/memory.c:2530: warning: `mmun_start' may be used uninitialized in this function
mm/memory.c:2531: warning: `mmun_end' may be used uninitialized in this function
It's much easier to initialize the variables to impossible values and do
a simple comparison to determine if they were initialized to remove the
bool entirely.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michel Lespinasse [Fri, 16 Nov 2012 22:14:47 +0000 (14:14 -0800)]
mm: add anon_vma_lock to validate_mm()
Iterating over the vma->anon_vma_chain without anon_vma_lock may cause
NULL ptr deref in anon_vma_interval_tree_verify(), because the node in the
chain might have been removed.
BUG: unable to handle kernel paging request at
fffffffffffffff0
IP: [<
ffffffff8122c29c>] anon_vma_interval_tree_verify+0xc/0xa0
PGD
4e28067 PUD
4e29067 PMD 0
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU 0
Pid: 9050, comm: trinity-child64 Tainted: G W
3.7.0-rc2-next-20121025-sasha-00001-g673f98e-dirty #77
RIP: 0010: anon_vma_interval_tree_verify+0xc/0xa0
Process trinity-child64 (pid: 9050, threadinfo
ffff880045f80000, task
ffff880048eb0000)
Call Trace:
validate_mm+0x58/0x1e0
vma_adjust+0x635/0x6b0
__split_vma.isra.22+0x161/0x220
split_vma+0x24/0x30
sys_madvise+0x5da/0x7b0
tracesys+0xe1/0xe6
RIP anon_vma_interval_tree_verify+0xc/0xa0
CR2:
fffffffffffffff0
Figured out by Bob Liu.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Michel Lespinasse <walken@google.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Fri, 9 Nov 2012 14:20:17 +0000 (15:20 +0100)]
KVM: x86: Fix invalid secondary exec controls in vmx_cpuid_update()
The commit [
ad756a16: KVM: VMX: Implement PCID/INVPCID for guests with
EPT] introduced the unconditional access to SECONDARY_VM_EXEC_CONTROL,
and this triggers kernel warnings like below on old CPUs:
vmwrite error: reg 401e value
a0568000 (err 12)
Pid: 13649, comm: qemu-kvm Not tainted 3.7.0-rc4-test2+ #154
Call Trace:
[<
ffffffffa0558d86>] vmwrite_error+0x27/0x29 [kvm_intel]
[<
ffffffffa054e8cb>] vmcs_writel+0x1b/0x20 [kvm_intel]
[<
ffffffffa054f114>] vmx_cpuid_update+0x74/0x170 [kvm_intel]
[<
ffffffffa03629b6>] kvm_vcpu_ioctl_set_cpuid2+0x76/0x90 [kvm]
[<
ffffffffa0341c67>] kvm_arch_vcpu_ioctl+0xc37/0xed0 [kvm]
[<
ffffffff81143f7c>] ? __vunmap+0x9c/0x110
[<
ffffffffa0551489>] ? vmx_vcpu_load+0x39/0x1a0 [kvm_intel]
[<
ffffffffa0340ee2>] ? kvm_arch_vcpu_load+0x52/0x1a0 [kvm]
[<
ffffffffa032dcd4>] ? vcpu_load+0x74/0xd0 [kvm]
[<
ffffffffa032deb0>] kvm_vcpu_ioctl+0x110/0x5e0 [kvm]
[<
ffffffffa032e93d>] ? kvm_dev_ioctl+0x4d/0x4a0 [kvm]
[<
ffffffff8117dc6f>] do_vfs_ioctl+0x8f/0x530
[<
ffffffff81139d76>] ? remove_vma+0x56/0x60
[<
ffffffff8113b708>] ? do_munmap+0x328/0x400
[<
ffffffff81187c8c>] ? fget_light+0x4c/0x100
[<
ffffffff8117e1a1>] sys_ioctl+0x91/0xb0
[<
ffffffff815a942d>] system_call_fastpath+0x1a/0x1f
This patch adds a check for the availability of secondary exec
control to avoid these warnings.
Cc: <stable@vger.kernel.org> [v3.6+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Linus Torvalds [Fri, 16 Nov 2012 22:10:15 +0000 (14:10 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking updates from David Miller:
1) tx_filtered/ps_tx_buf queues need to be accessed with the SKB queue
lock, from Arik Nemtsov.
2) Don't call 802.11 driver's filter configure method until it's
actually open, from Felix Fietkau.
3) Use ieee80211_free_txskb otherwise we leak control information.
From Johannes Berg.
4) Fix memory leak in bluetooth UUID removal,f rom Johan Hedberg.
5) The shift mask trick doesn't work properly when 'optname' is out of
range in do_ip_setsockopt(). Use a straightforward switch statement
instead, the compiler emits essentially the same code but without
the missing range check. From Xi Wang.
6) Fix when we call tcp_replace_ts_recent() otherwise we can
erroneously accept a too-high tsval. From Eric Dumazet.
7) VXLAN bug fixes, mostly to do with VLAN header length handling, from
Alexander Duyck.
8) Missing return value initialization for IPV6_MINHOPCOUNT socket
option handling. From Hannes Frederic.
9) Fix regression in tasklet handling in jme/ksz884x/xilinx drivers,
from Xiaotian Feng.
10) At smsc911x driver init time, we don't know if the chip is in word
swap mode or not. However we do need to wait for the control
register's ready bit to be set before we program any other part of
the chip. Adjust the wait loop to account for this. From Kamlakant
Patel.
11) Revert erroneous MDIO bus unregister change to mdio-bitbang.c
12) Fix memory leak in /proc/net/sctp/, from Tommi Rantala.
13) tilegx driver registers IRQ with NULL name, oops, from Simon Marchi.
14) TCP metrics hash table kzalloc() based allocation can fail, back
down to using vmalloc() if it does. From Eric Dumazet.
15) Fix packet steering out-of-order delivery regression, from Tom
Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net-rps: Fix brokeness causing OOO packets
tcp: handle tcp_net_metrics_init() order-5 memory allocation failures
batman-adv: process broadcast packets in BLA earlier
batman-adv: don't add TEMP clients belonging to other backbone nodes
batman-adv: correctly pass the client flag on tt_response
batman-adv: fix tt_global_entries flags update
tilegx: request_irq with a non-null device name
net: correct check in dev_addr_del()
tcp: fix retransmission in repair mode
sctp: fix /proc/net/sctp/ memory leak
Revert "drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free"
net/smsc911x: Fix ready check in cases where WORD_SWAP is needed
drivers/net: fix tasklet misuse issue
ipv4/ip_vti.c: VTI fix post-decryption forwarding
brcmfmac: fix typo in CONFIG_BRCMISCAN
vxlan: Update hard_header_len based on lowerdev when instantiating VXLAN
vxlan: fix a typo.
ipv6: setsockopt(IPIPPROTO_IPV6, IPV6_MINHOPCOUNT) forgot to set return value
doc/net: Fix typo in netdev-features.txt
vxlan: Fix error that was resulting in VXLAN MTU size being 10 bytes too large
...
David S. Miller [Fri, 16 Nov 2012 19:37:18 +0000 (14:37 -0500)]
Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless
John W. Linville says:
====================
This batch of fixes is intended for the 3.7 stream...
This includes a pull of the Bluetooth tree. Gustavo says:
"A few important fixes to go into 3.7. There is a new hw support by Marcos
Chaparro. Johan added a memory leak fix and hci device index list fix.
Also Marcel fixed a race condition in the device set up that was prevent the
bt monitor to work properly. Last, Paulo Sérgio added a fix to the error
status when pairing for LE fails. This was prevent userspace to work to handle
the failure properly."
Regarding the mac80211 pull, Johannes says:
"I have a locking fix for some SKB queues, a variable initialization to
avoid crashes in a certain failure case, another free_txskb fix from
Felix and another fix from him to avoid calling a stopped driver, a fix
for a (very unlikely) memory leak and a fix to not send null data
packets when resuming while not associated."
Regarding the iwlwifi pull, Johannes says:
"Two more fixes for iwlwifi ... one to use ieee80211_free_txskb(), and
one to check DMA mapping errors, please pull."
On top of that, Johannes also included a wireless regulatory fix
to allow 40 MHz on channels 12 and 13 in world roaming mode. Also,
Hauke Mehrtens fixes a #ifdef typo in brcmfmac.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Fri, 16 Nov 2012 09:04:15 +0000 (09:04 +0000)]
net-rps: Fix brokeness causing OOO packets
In commit
c445477d74ab3779 which adds aRFS to the kernel, the CPU
selected for RFS is not set correctly when CPU is changing.
This is causing OOO packets and probably other issues.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Nov 2012 18:38:12 +0000 (13:38 -0500)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included fixes are:
- update the client entry status flags when using the "early client
detection". This makes the Distributed AP isolation correctly work;
- transfer the client entry status flags when recovering the translation
table from another node. This makes the Distributed AP isolation correctly
work;
- prevent the "early client detection mechanism" to add clients belonging to
other backbone nodes in the same LAN. This breaks connectivity when using this
mechanism together with the Bridge Loop Avoidance
- process broadcast packets with the Bridge Loop Avoidance before any other
component. BLA can possibly drop the packets based on the source address. This
makes the "early client detection mechanism" correctly work when used with
BLA.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 16 Nov 2012 05:31:53 +0000 (05:31 +0000)]
tcp: handle tcp_net_metrics_init() order-5 memory allocation failures
order-5 allocations can fail with current kernels, we should
try vmalloc() as well.
Reported-by: Julien Tinnes <jln@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Rui [Thu, 15 Nov 2012 00:58:27 +0000 (08:58 +0800)]
Thermal: Add Linux/Thermal subsystem info in MAINTAINER file
All the changes made to the generic thermal layer, or platform thermal
drivers that make use of the thermal layer, should be sent to
linux-pm@vger.kernel.org for discussion.
And as the maintainer, I will only apply the patches that have been sent
to linux-pm@vger.kernel.org.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Tue, 13 Nov 2012 01:53:04 +0000 (17:53 -0800)]
mm, oom: reintroduce /proc/pid/oom_adj
This is mostly a revert of
01dc52ebdf47 ("oom: remove deprecated oom_adj")
from Davidlohr Bueso.
It reintroduces /proc/pid/oom_adj for backwards compatibility with earlier
kernels. It simply scales the value linearly when /proc/pid/oom_score_adj
is written.
The major difference is that its scheduled removal is no longer included
in Documentation/feature-removal-schedule.txt. We do warn users with a
single printk, though, to suggest the more powerful and supported
/proc/pid/oom_score_adj interface.
Reported-by: Artem S. Tashkinov <t.artem@lycos.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Nov 2012 18:08:45 +0000 (10:08 -0800)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on this longer than we meant to due to travel and
other activities, but the number of patches is luckily not that high.
Biggest changes are from a batch of OMAP bugfixes, but there are a few
for the broader set of SoCs too (bcm2835, pxa, highbank, tegra, at91
and i.MX).
The OMAP patches contain some fixes for MUSB/PHY on omap4 which ends
up being a bit on the large side but needed for legacy (non-DT)
platforms. Beyond that there are a handful of hwmod/pm changes.
So, fairly noncontroversial stuff all in all, and as usual around this
time the fixes are well targeted at specific problems."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: ehci: fix host power mask bit
ARM i.MX: fix error-valued pointer dereference in clk_register_gate2()
ARM: at91/usbh: fix overcurrent gpio setup
ARM: at91/AT91SAM9G45: fix crypto peripherals irq issue due to sparse irq support
ARM: boot: Fix usage of kecho
ARM: OMAP: ocp2scp: create omap device for ocp2scp
ARM: OMAP4: add _dev_attr_ to ocp2scp for representing usb_phy
drivers: bus: ocp2scp: add pdata support
irqchip: irq-bcm2835: Add terminating entry for of_device_id table
ARM: highbank: retry wfi on reset request
ARM: OMAP4: PM: fix regulator name for VDD_MPU
ARM: OMAP4: hwmod data: do not enable or reset the McPDM during kernel init
ARM: OMAP2+: hwmod: add flag to prevent hwmod code from touching IP block during init
ARM: dt: tegra: fix length of pad control and mux registers
ARM: OMAP: hwmod: wait for sysreset complete after enabling hwmod
ARM: OMAP2+: clockdomain: Fix OMAP4 ISS clk domain to support only SWSUP
ARM: pxa/spitz_pm: Fix hang when resuming from STR
ARM: pxa: hx4700: Fix backlight PWM device number
ARM: OMAP2+: PM: add missing newline to VC warning message
John W. Linville [Fri, 16 Nov 2012 17:59:13 +0000 (12:59 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless into for-davem
Linus Torvalds [Fri, 16 Nov 2012 16:32:07 +0000 (08:32 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 bugfix from Catalin Marinas:
"Arm64 page permission bug fix.
Without this fix, the CPU speculatively accesses the interrupt
controller memory causing random IRQ acknowledge."
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Distinguish between user and kernel XN bits
Linus Torvalds [Fri, 16 Nov 2012 15:58:20 +0000 (07:58 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
"This has a build fix for architectures where memcmp() is macro, from
Jiri Slaby"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: microsoft: do not use compound literal - fix build
Catalin Marinas [Thu, 15 Nov 2012 17:21:16 +0000 (17:21 +0000)]
arm64: Distinguish between user and kernel XN bits
On AArch64, the meaning of the XN bit has changed to UXN (user). The PXN
(privileged) bit must be set to prevent kernel execution. Without the
PXN bit set, the CPU may speculatively access device memory. This patch
ensures that all the mappings that the kernel must not execute from
(including user mappings) have the PXN bit set.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Fri, 16 Nov 2012 15:47:18 +0000 (07:47 -0800)]
Merge tag 'usb-3.7-rc5' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some USB fixes for the 3.7 tree.
Nothing huge here, just a number of tiny bugfixes resolving issues
that have been found, and two reverts of patches that were found to
have caused problems.
All of these have been in linux-next already.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USB/host: Cleanup unneccessary irq disable code"
USB: option: add Alcatel X220/X500D USB IDs
USB: option: add Novatel E362 and Dell Wireless 5800 USB IDs
USB: keyspan: fix typo causing GPF on open
USB: fix build with XEN and EARLY_PRINTK_DBGP enabled but USB_SUPPORT disabled
USB: usb_wwan: fix bulk-urb allocation
usb: otg: Fix build errors if USB_MUSB_OMAP2PLUS is selected as module
usb: musb: ux500: fix 'musbid' undeclared error in ux500_remove()
Revert "usb: musb: use DMA mode 1 whenever possible"
Linus Torvalds [Fri, 16 Nov 2012 15:46:38 +0000 (07:46 -0800)]
Merge tag 'tty-3.7-rc5' of git://git./linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are two TTY driver fixes for 3.7-rc5.
They resolve a bug in the hvc driver that has been reported, and fix a
problem with the list of device ids in the max310x serial driver.
Both have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: max310x: Add terminating entry for spi_device_id table
TTY: hvc_console, fix port reference count going to zero prematurely
Linus Torvalds [Fri, 16 Nov 2012 15:46:04 +0000 (07:46 -0800)]
Merge tag 'staging-3.7-rc5' of git://git./linux/kernel/git/gregkh/staging
Pull staging tree fix from Greg Kroah-Hartman:
"Here is a single patch, a revert of an android driver patch, that
resolves a bug that has been reported in the Android alarm driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: Android alarm: IOCTL command encoding fix"
Arnd Bergmann [Fri, 16 Nov 2012 15:43:58 +0000 (16:43 +0100)]
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre <nicolas.ferre@atmel.com>:
Two little fixes, one related to the move to sparse irq and
another one fixing the check of a GPIO for USB host overcurrent.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/usbh: fix overcurrent gpio setup
ARM: at91/AT91SAM9G45: fix crypto peripherals irq issue due to sparse irq support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 16 Nov 2012 15:42:59 +0000 (16:42 +0100)]
Merge tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6 into fixes
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX fixes for 3.7-rc
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: ehci: fix host power mask bit
ARM i.MX: fix error-valued pointer dereference in clk_register_gate2()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linus Torvalds [Fri, 16 Nov 2012 15:39:30 +0000 (07:39 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Some more bug fixes and a config change.
The signal bug is nasty, if the clock_gettime vdso function is
interrupted by a signal while in access-register-mode we end up with
an endless signal loop until the signal stack is full. The config
change is for aligned struct pages, gives us 8% improvement with
hackbench."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/3215: fix tty close handling
s390/mm: have 16 byte aligned struct pages
s390/gup: fix access_ok() usage in __get_user_pages_fast()
s390/gup: add missing TASK_SIZE check to get_user_pages_fast()
s390/topology: fix core id vs physical package id mix-up
s390/signal: set correct address space control
Linus Torvalds [Fri, 16 Nov 2012 15:32:32 +0000 (07:32 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"All pretty normal: one TTM oops fix, one radeon, a few intel and a
vmwgfx fix."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: remove unneeded preempt_disable/enable
ttm: Clear the ttm page allocated from high memory zone correctly
vmwgfx: return an -EFAULT if copy_to_user() fails
drm/radeon: fix logic error in atombios_encoders.c
drm/i915: do not ignore eDP bpc settings from vbt
drm/i915/sdvo: clean up connectors on intel_sdvo_init() failures
drm/i915/crt: fix DPMS standby and suspend mode handling
Linus Torvalds [Fri, 16 Nov 2012 15:19:45 +0000 (07:19 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull another clk layer fix from Michael Turquette:
"GCC 4.7 users get compilation errors from unnecessary use of inline in
clk-provider.h. This pull request fixes the regression by removing
inline usage from those function declarations."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: remove inline usage from clk-provider.h
Christoph Fritz [Fri, 16 Nov 2012 14:39:24 +0000 (15:39 +0100)]
ARM: imx: ehci: fix host power mask bit
This patch sets HPM (Host power mask bit) to bit 16 according to i.MX
Reference Manual. Falsely it was set to bit 8, but this controls pull-up
Impedance.
Reported-by: Michael Burkey <mdburkey@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Acked-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Wei Yongjun [Thu, 25 Oct 2012 15:02:18 +0000 (23:02 +0800)]
ARM i.MX: fix error-valued pointer dereference in clk_register_gate2()
The error-valued pointer clk is used for the arg of kfree, it should be
kfree(gate) if clk_register() return ERR_PTR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Johan Hovold [Wed, 14 Nov 2012 11:18:17 +0000 (12:18 +0100)]
ARM: at91/usbh: fix overcurrent gpio setup
Use gpio_is_valid also for overcurrent pins (which are currently
negative in many board files).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Royer [Tue, 6 Nov 2012 16:31:03 +0000 (17:31 +0100)]
ARM: at91/AT91SAM9G45: fix crypto peripherals irq issue due to sparse irq support
Spare irq support introduced by commit
8fe82a5 (ARM: at91: sparse irq support)
involves to add the NR_IRQS_LEGACY offset to irq number.
Signed-off-by: Nicolas Royer <nicolas@eukrea.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Eric Bénard <eric@eukrea.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Cc: stable@vger.kernel.org # 3.6
Antonio Quartulli [Thu, 8 Nov 2012 20:55:30 +0000 (21:55 +0100)]
batman-adv: process broadcast packets in BLA earlier
The logic in the BLA mechanism may decide to drop broadcast packets
because the node may still be in the setup phase. For this reason,
further broadcast processing like the early client detection mechanism
must be done only after the BLA check.
This patches moves the invocation to BLA before any other broadcast
processing.
This was introduced
30cfd02b60e1cb16f5effb0a01f826c5bb7e4c59
("batman-adv: detect not yet announced clients")
Reported-by: Glen Page <glen.page@thet.net>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Antonio Quartulli [Thu, 8 Nov 2012 20:55:29 +0000 (21:55 +0100)]
batman-adv: don't add TEMP clients belonging to other backbone nodes
The "early client detection" mechanism must not add clients belonging
to other backbone nodes. Such clients must be reached by directly
using the LAN instead of the mesh.
This was introduced by
30cfd02b60e1cb16f5effb0a01f826c5bb7e4c59
("batman-adv: detect not yet announced clients")
Reported-by: Glen Page <glen.page@thet.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Antonio Quartulli [Thu, 8 Nov 2012 13:21:11 +0000 (14:21 +0100)]
batman-adv: correctly pass the client flag on tt_response
When a TT response with the full table is sent, the client flags
should be sent as well. This patch fix the flags assignment when
populating the tt_response to send back
This was introduced by
30cfd02b60e1cb16f5effb0a01f826c5bb7e4c59
("batman-adv: detect not yet announced clients")
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Antonio Quartulli [Wed, 7 Nov 2012 14:05:33 +0000 (15:05 +0100)]
batman-adv: fix tt_global_entries flags update
Flags carried by a change_entry have to be always copied into the
client entry as they may contain important attributes (e.g.
TT_CLIENT_WIFI).
For instance, a client added by means of the "early detection
mechanism" has no flag set at the beginning, so they must be updated once the
proper ADD event is received.
This was introduced by
30cfd02b60e1cb16f5effb0a01f826c5bb7e4c59
("batman-adv: detect not yet announced clients")
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Simon Marchi [Thu, 15 Nov 2012 18:13:19 +0000 (18:13 +0000)]
tilegx: request_irq with a non-null device name
This patch simply makes the tilegx net driver call request_irq with a
non-null name. It makes the output in /proc/interrupts more obvious, but
also helps tools that don't expect to find null there.
Signed-off-by: Simon Marchi <simon.marchi@polymtl.ca>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Fri, 16 Nov 2012 00:00:43 +0000 (10:00 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
Just a few small things to fix regressions, somehow all patches from Jani:
- Fix dpms confusion about which platforms support intermediate modes on
vga.
- Revert the "ignore vbt for eDP bpc" patch, it breaks machines. This will
annoy mbp retina owners again, but windows machines seem to _really_
depend upon this. We can try to quirk the mbp retinas again in 3.8 and
backport the patch.
- Fix connector leaks when the sdvo setup failed, resulted in an OOPS
later on when trying to probe that connector (with it's encoder kfree'd
already).
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: do not ignore eDP bpc settings from vbt
drm/i915/sdvo: clean up connectors on intel_sdvo_init() failures
drm/i915/crt: fix DPMS standby and suspend mode handling
Dave Airlie [Fri, 16 Nov 2012 00:00:24 +0000 (10:00 +1000)]
Merge branch 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just a single radeon fix from Alex.
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix logic error in atombios_encoders.c
Akinobu Mita [Fri, 9 Nov 2012 12:10:43 +0000 (12:10 +0000)]
drm/ttm: remove unneeded preempt_disable/enable
It is unnecessary to disable preemption explicitly while calling
copy_highpage(). Because copy_highpage() will do it again through
kmap_atomic/kunmap_atomic.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Zhao Yakui [Tue, 13 Nov 2012 18:31:55 +0000 (18:31 +0000)]
ttm: Clear the ttm page allocated from high memory zone correctly
The TTM page can be allocated from high memory. In such case it is
wrong to use the page_address(page) as the virtual address for the high memory
page.
bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50241
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dan Carpenter [Mon, 12 Nov 2012 11:07:24 +0000 (11:07 +0000)]
vmwgfx: return an -EFAULT if copy_to_user() fails
copy_to_user() returns the number of bytes remaining to be copied, but
we want to return a negative error code here. I fixed a couple of these
last year, but I missed this one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jiri Pirko [Wed, 14 Nov 2012 02:51:04 +0000 (02:51 +0000)]
net: correct check in dev_addr_del()
Check (ha->addr == dev->dev_addr) is always true because dev_addr_init()
sets this. Correct the check to behave properly on addr removal.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Vagin [Thu, 15 Nov 2012 04:03:17 +0000 (04:03 +0000)]
tcp: fix retransmission in repair mode
Currently if a socket was repaired with a few packet in a write queue,
a kernel bug may be triggered:
kernel BUG at net/ipv4/tcp_output.c:2330!
RIP: 0010:[<
ffffffff8155784f>] tcp_retransmit_skb+0x5ff/0x610
According to the initial realization
v3.4-rc2-963-gc0e88ff,
all skb-s should look like already posted. This patch fixes code
according with this sentence.
Here are three points, which were not done in the initial patch:
1. A tcp send head should not be changed
2. Initialize TSO state of a skb
3. Reset the retransmission time
This patch moves logic from tcp_sendmsg to tcp_write_xmit. A packet
passes the ussual way, but isn't sent to network. This patch solves
all described problems and handles tcp_sendpages.
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Mazanov [Thu, 15 Nov 2012 17:07:00 +0000 (21:07 +0400)]
clk: remove inline usage from clk-provider.h
Users of GCC 4.7 have reported compiler errors due to having inline
applied to function declarations in clk-provider.h. The definitions
exist in drivers/clk/clk.c. An example error:
In file included from arch/arm/mach-omap2/clockdomain.c:25:0:
arch/arm/mach-omap2/clockdomain.c: In function ‘clkdm_clk_disable’:
include/linux/clk-provider.h:338:12: error: inlining failed in call to always_inline ‘__clk_get_enable_count’: function body not available
arch/arm/mach-omap2/clockdomain.c:1001:28: error: called from here
make[1]: *** [arch/arm/mach-omap2/clockdomain.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
This patch removes the use of inline from include/linux/clk-provider.h
but keeps the function definitions in drivers/clk/clk.c as inlined since
they are one-liners.
Signed-off-by: Igor Mazanov <i.mazanov@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: improved subject, added changelog]
Linus Torvalds [Thu, 15 Nov 2012 19:34:45 +0000 (11:34 -0800)]
Merge tag 'for-linus' of git://github.com/gxt/linux
Pull unicore32 update from Guan Xuetao.
* tag 'for-linus' of git://github.com/gxt/linux:
arch/unicore32: remove CONFIG_EXPERIMENTAL
unicore32: switch to generic sys_execve()
unicore32: switch to generic kernel_thread()/kernel_execve()
unicore32: Use Kbuild infrastructure for kvm_para.h
UAPI: (Scripted) Disintegrate arch/unicore32/include/asm
UniCore32-bugfix: Remove definitions in asm/bug.h to solve difference between native and cross compiler
UniCore32-bugfix: fix mismatch return value of __xchg_bad_pointer
UniCore32 bugfix: add missed CONFIG_ZONE_DMA
unicore32/mm/fault.c: Port OOM changes to do_pf
Linus Torvalds [Thu, 15 Nov 2012 19:28:43 +0000 (11:28 -0800)]
Merge tag 'upstream-3.7-rc6' of git://git.infradead.org/linux-ubifs
Pull UBIFS fixes from Artem Bityutskiy:
"Two patches which fix a problem reported by several people in the
past, but only fixed now because no one gave enough material for
debugging.
Anyway, these fix the problem that sometimes after a power cut the
file-system is not mountable with the following symptom:
grab_empty_leb: could not find an empty LEB
The fixes make the file-system mountable again."
* tag 'upstream-3.7-rc6' of git://git.infradead.org/linux-ubifs:
UBIFS: fix mounting problems after power cuts
UBIFS: introduce categorized lprops counter
Linus Torvalds [Thu, 15 Nov 2012 19:27:53 +0000 (11:27 -0800)]
Merge tag 'for-v3.7-fixes' of git://git.infradead.org/users/cbou/linux-pstore
Pull pstore fix from Anton Vorontsov:
"A small fixup for the persistent storage subsystem. The bug can
prevent kernel booting on a APEI-enabled machines w/ PSTORE_CONSOLE=y
(this is N by default, though)."
* tag 'for-v3.7-fixes' of git://git.infradead.org/users/cbou/linux-pstore:
pstore: Fix NULL pointer dereference in console writes
Linus Torvalds [Thu, 15 Nov 2012 19:25:39 +0000 (11:25 -0800)]
Merge branch 'i2c-for-linus' of git://git./linux/kernel/git/jdelvare/staging
Pill i2c fixes from Jean Delvare.
Well, "fixes".. The biggest patch here is actually Jan marking Wolfram
Sang as the main i2c subsystem maintainer, with Jan staying on as the PC
controller maintainer.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-mux-pinctrl: Fix probe error path
MAINTAINERS: i2c: 7 years, this is it
Linus Torvalds [Thu, 15 Nov 2012 19:22:03 +0000 (11:22 -0800)]
Merge tag 'regulator-3.7' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few fixes for teardown issues that will be rarely seen, plus a fix
for a silly bug in regulator_is_supported_voltage() which shows how
often the answer to the question should be false.
The supported voltage commit is very new as I just edited to add a Cc
to stable, the code itself has been in -next."
* tag 'regulator-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fix voltage check in regulator_is_supported_voltage()
regulator: core: Avoid deadlock when regulator_register fails
Regulator: core: Unregister when gpio request fails.
Linus Torvalds [Thu, 15 Nov 2012 19:21:28 +0000 (11:21 -0800)]
Merge tag 'sound-3.7' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The only large LOC is seen in WM5102 driver, just writing a bunch of
register updates, but the actual code change is small. Other than
that, all small fixes suitable for rc6."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix mutex deadlock at disconnection
ALSA: fm801: precedence bug in snd_fm801_tea575x_get_pins()
ALSA: es1968: precedence bug in snd_es1968_tea575x_get_pins()
ALSA: hda - Add a missing quirk entry for iMac 9,1
ASoC: core: Double control update err for snd_soc_put_volsw_sx
ASoC: dapm: Use card_list during DAPM shutdown
ASoC: cs42l52: fix the return value of cs42l52_set_fmt()
ASoC: bells: Correct type in sub speaker DAI name for WM5102
ASoC: wm8978: pll incorrectly configured when codec is master
ASoC: mxs-saif: Fix channel swap for 24-bit format
ASoC: bells: Select WM1250-EV1 Springbank audio I/O module
ASoC: bells: Add missing select of WM0010
ASoC: mxs-saif: Add MODULE_ALIAS
ASoC: wm5102: Write register value corrections after SYSCLK is enabled
Tommi Rantala [Thu, 15 Nov 2012 03:49:05 +0000 (03:49 +0000)]
sctp: fix /proc/net/sctp/ memory leak
Commit
13d782f ("sctp: Make the proc files per network namespace.")
changed the /proc/net/sctp/ struct file_operations opener functions to
use single_open_net() and seq_open_net().
Avoid leaking memory by using single_release_net() and seq_release_net()
as the release functions.
Discovered with Trinity (the syscall fuzzer).
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Carstens [Thu, 15 Nov 2012 08:22:40 +0000 (09:22 +0100)]
s390/3215: fix tty close handling
The 3215 console always has the RAW3215_FIXED flag set, which causes
raw3215_shutdown() not to wait for outstanding I/O requests if an attached
tty gets closed.
The flag however can be simply removed, so we can guarantee that all requests
belonging to the tty have been processed when the tty is closed.
However the tasklet that belongs to the 3215 device may be scheduled even if
there is no tty attached anymore, since we have a race between console and tty
processing.
Thefore unconditional tty_wakekup() in raw3215_wakeup() can cause the following
NULL pointer dereference:
3.465368 Unable to handle kernel pointer dereference at virtual kernel address (null)
3.465448 Oops: 0004 #1 SMP
3.465454 Modules linked in:
3.465459 CPU: 1 Not tainted 3.6.0 #1
3.465462 Process swapper/1 (pid: 0, task:
000000003ffa4428, ksp:
000000003ffb7ce0)
3.465466 Krnl PSW :
0404100180000000 0000000000162f86 (__wake_up+0x46/0xb8)
3.465480 R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:1 PM:0 EA:3
Krnl GPRS:
fffffffffffffffe 0000000000000000 0000000000000160 0000000000000001
3.465492
0000000000000001 0000000000000004 0000000000000004 000000000096b490
3.465499
0000000000000001 0000000000000100 0000000000000001 0000000000000001
3.465506
070000003fc87d60 0000000000000160 000000003fc87d68 000000003fc87d00
3.465526 Krnl Code:
0000000000162f76:
e3c0f0a80004 lg %r12,168(%r15)
0000000000162f7c:
58000370 l %r0,880
#
0000000000162f80:
c007ffffffff00 xilf %r0,
4294967295
>
0000000000162f86:
ba102000 cs %r1,%r0,0(%r2)
0000000000162f8a: 1211 ltr %r1,%r1
0000000000162f8c:
a774002f brc 7,162fea
0000000000162f90:
b904002d lgr %r2,%r13
0000000000162f94:
b904003a lgr %r3,%r10
3.465597 Call Trace:
3.465599 (<
0400000000000000> 0x400000000000000)
3.465602 <
000000000048c77e> raw3215_wakeup+0x2e/0x40
3.465607 <
0000000000134d66> tasklet_action+0x96/0x168
3.465612 <
000000000013423c> __do_softirq+0xd8/0x21c
3.465615 <
0000000000134678> irq_exit+0xa8/0xac
3.465617 <
000000000046c232> do_IRQ+0x182/0x248
3.465621 <
00000000005c8296> io_return+0x0/0x8
3.465625 <
00000000005c7cac> vtime_stop_cpu+0x4c/0xb8
3.465629 (<
0000000000194e06> tick_nohz_idle_enter+0x4e/0x74)
3.465633 <
0000000000104760> cpu_idle+0x170/0x184
3.465636 <
00000000005b5182> smp_start_secondary+0xd6/0xe0
3.465641 <
00000000005c86be> restart_int_handler+0x56/0x6c
3.465643 <
0000000000000000> 0x0
3.465645 Last Breaking-Event-Address:
3.465647 <
0000000000403136> tty_wakeup+0x46/0x98
3.465652
3.465654 Kernel panic - not syncing: Fatal exception in interrupt
01: HCPGIR450W CP entered; disabled wait PSW
00020001 80000000 00000000 0010F63C
The easiest solution is simply to check if tty is NULL in the tasklet.
If it is NULL nothing is to do (no tty attached), otherwise tty_wakeup()
can be called, since we hold a reference to the tty.
This is not nice... but it is a small patch and it works.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Alex Deucher [Wed, 14 Nov 2012 14:10:39 +0000 (09:10 -0500)]
drm/radeon: fix logic error in atombios_encoders.c
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=50431
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
David S. Miller [Thu, 15 Nov 2012 03:32:15 +0000 (22:32 -0500)]
Revert "drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free"
This reverts commit
aa731872f7d33dcb8b54dad0cfb82d4e4d195d7e.
As pointed out by Ben Hutchings, this change is not correct.
mdiobus_unregister() can't be called if the bus isn't registered yet,
however this change can result in situations which cause that to
happen.
Part of the confusion here revolves around the fact that the
callers of this module control registration/unregistration,
rather than the module itself.
Signed-off-by: David S. Miller <davem@davemloft.net>
Kamlakant Patel [Wed, 14 Nov 2012 01:41:38 +0000 (01:41 +0000)]
net/smsc911x: Fix ready check in cases where WORD_SWAP is needed
The chip ready check added by the commit
3ac3546e [Always wait for
the chip to be ready] does not work when the register read/write
is word swapped. This check has been added before the WORD_SWAP
register is programmed, so we need to check for swapped register
value as well.
Bit 16 is marked as RESERVED in SMSC datasheet, Steve Glendinning
<steve@shawell.net> checked with SMSC and wrote:
The chip architects have concluded we should be reading PMT_CTRL
until we see any of bits 0, 8, 16 or 24 set. Then we should read
BYTE_TEST to check the byte order is correct (as we already do).
The rationale behind this is that some of the chip variants have
word order swapping features too, so the READY bit could actually
be in any of the 4 possible locations. The architects have confirmed
that if any of these 4 positions is set the chip is ready. The other
3 locations will either never be set or can only go high after READY
does (so also indicate the device is ready).
This change will check for the READY bit at the 16th position. We do
not check the other two cases (bit 8 and 24) since the driver does not
support byte-swapped register read/write.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xiaotian Feng [Tue, 13 Nov 2012 19:47:36 +0000 (19:47 +0000)]
drivers/net: fix tasklet misuse issue
In commit
175c0dff, drivers uses tasklet_kill to avoid put disabled tasklet
on the tasklet vec. But some of the drivers uses tasklet_init & tasklet_disable
in the driver init code, then tasklet_enable when it is opened. This makes
tasklet_enable on a killed tasklet and make ksoftirqd crazy then. Normally,
drivers should use tasklet_init/tasklet_kill on device open/remove, and use
tasklet_disable/tasklet_enable on device suspend/resume.
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Saurabh Mohan [Thu, 15 Nov 2012 02:08:15 +0000 (18:08 -0800)]
ipv4/ip_vti.c: VTI fix post-decryption forwarding
With the latest kernel there are two things that must be done post decryption
so that the packet are forwarded.
1. Remove the mark from the packet. This will cause the packet to not match
the ipsec-policy again. However doing this causes the post-decryption check to
fail also and the packet will get dropped. (cat /proc/net/xfrm_stat).
2. Remove the sp association in the skbuff so that no policy check is done on
the packet for VTI tunnels.
Due to #2 above we must now do a security-policy check in the vti rcv path
prior to resetting the mark in the skbuff.
Signed-off-by: Saurabh Mohan <saurabh.mohan@vyatta.com>
Reported-by: Ruben Herold <ruben@puettmann.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 14 Nov 2012 11:49:53 +0000 (11:49 +0000)]
pstore: Fix NULL pointer dereference in console writes
Passing a NULL id causes a NULL pointer deference in writers such as
erst_writer and efi_pstore_write because they expect to update this id.
Pass a dummy id instead.
This avoids a cascade of oopses caused when the initial
pstore_console_write passes a null which in turn causes writes to the
console causing further oopses in subsequent pstore_console_write calls.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Mark Brown [Thu, 15 Nov 2012 02:16:02 +0000 (11:16 +0900)]
Merge remote-tracking branches 'regulator/fix/gpio', 'regulator/fix/put' and 'regulator/fix/supp-volt' into tmp
Marek Szyprowski [Tue, 13 Nov 2012 08:48:51 +0000 (09:48 +0100)]
regulator: fix voltage check in regulator_is_supported_voltage()
regulator_is_supported_voltage() should return true only if the voltage
of fixed/constant regulator is between min_uV and max_uV.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Axel Lin [Sun, 4 Nov 2012 15:34:18 +0000 (23:34 +0800)]
tty: serial: max310x: Add terminating entry for spi_device_id table
The spi_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Wed, 14 Nov 2012 21:46:40 +0000 (13:46 -0800)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux
Pull power tools fixes from Len Brown:
"A pair of power tools patches -- a 3.7 regression fix plus a bug fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: graceful fail on garbage input
tools/power turbostat: Repair Segmentation fault when using -i option
Linus Torvalds [Wed, 14 Nov 2012 21:45:23 +0000 (13:45 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS update from Ralf Baechle:
"To avoid unnecessary risk and work the preemption fixes are combined
with some preparatory work that isn't strictly required. So it's
really just 3 fixes:
- Get is_compat_task() to do the right thing while simplifying it.
The unnecessary complexity hid a rarely striking bug which could be
triggered by ext3/ext4 under certain circumstances.
- Resolve a preemption issue in the irqflags.h functions for kernels
built to support pre-MIPS32 / pre-MIPS64 Release 2 processors.
- Fix the interrupt number of the MIPS Malta's CBUS UART."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Malta: Fix interupt number of CBUS UART.
MIPS: Make irqflags.h functions preempt-safe for non-mipsr2 cpus
MIPS: Remove irqflags.h dependency from bitops.h
MIPS: bitops.h: Change use of 'unsigned short' to 'int'
MIPS: compat: Delete now unused TIF_32BIT.
MIPS: compat: Implement is_compat_task() by testing for 32-bit address space.
MIPS: compat: Fix use of TIF_32BIT_ADDR vs _TIF_32BIT_ADDR
Linus Torvalds [Wed, 14 Nov 2012 21:44:04 +0000 (13:44 -0800)]
Merge branch 'for-3.7-fixes' of git://git./linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"This contains two fix patches for device_cgroup. One fixes a
regression introduced earlier in 3.7 cycle where device_cgroup could
try to dereference the NULL parent of the root cgroup. The other one
is RCU usage fix."
* 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: fix RCU usage
device_cgroup: fix unchecked cgroup parent usage
Paul Mackerras [Wed, 14 Nov 2012 08:15:47 +0000 (19:15 +1100)]
TTY: hvc_console, fix port reference count going to zero prematurely
Commit
bdb498c20040 "TTY: hvc_console, add tty install" took the port
refcounting out of hvc_open()/hvc_close(), but failed to remove the
kref_put() and tty_kref_put() calls in hvc_hangup() that were there to
remove the extra references that hvc_open() had taken.
The result was that doing a vhangup() when the current terminal was
a hvc_console, then closing the current terminal, would end up calling
destroy_hvc_struct() and making the port disappear entirely. This
meant that Fedora 17 systems would boot up but then not display the
login prompt on the console, and attempts to open /dev/hvc0 would
give a "No such device" error.
This fixes it by removing the extra kref_put() and tty_kref_put() calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hauke Mehrtens [Sun, 4 Nov 2012 22:13:09 +0000 (23:13 +0100)]
brcmfmac: fix typo in CONFIG_BRCMISCAN
The old ifdef CONFIG_BRCMFISCAN looks wrong to me and it makes more
sense when CONFIG_BRCMISCAN is used.
This patch was just compile tested by me, but not runtime tested.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 14 Nov 2012 19:17:58 +0000 (14:17 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/bluetooth/bluetooth
John W. Linville [Wed, 14 Nov 2012 19:16:54 +0000 (14:16 -0500)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-fixes
John W. Linville [Wed, 14 Nov 2012 19:15:43 +0000 (14:15 -0500)]
Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211
Takashi Iwai [Tue, 13 Nov 2012 10:22:48 +0000 (11:22 +0100)]
ALSA: usb-audio: Fix mutex deadlock at disconnection
The recent change for USB-audio disconnection race fixes introduced a
mutex deadlock again. There is a circular dependency between
chip->shutdown_rwsem and pcm->open_mutex, depicted like below, when a
device is opened during the disconnection operation:
A. snd_usb_audio_disconnect() ->
card.c::register_mutex ->
chip->shutdown_rwsem (write) ->
snd_card_disconnect() ->
pcm.c::register_mutex ->
pcm->open_mutex
B. snd_pcm_open() ->
pcm->open_mutex ->
snd_usb_pcm_open() ->
chip->shutdown_rwsem (read)
Since the chip->shutdown_rwsem protection in the case A is required
only for turning on the chip->shutdown flag and it doesn't have to be
taken for the whole operation, we can reduce its window in
snd_usb_audio_disconnect().
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Charles Keepax [Wed, 14 Nov 2012 09:39:31 +0000 (09:39 +0000)]
regulator: core: Avoid deadlock when regulator_register fails
When regulator_register fails and exits through the scrub path the
regulator_put function was called whilst holding the
regulator_list_mutex, causing deadlock.
This patch adds a private version of the regulator_put function which
can be safely called whilst holding the mutex, replacing the
aforementioned call.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dan Carpenter [Wed, 14 Nov 2012 08:23:54 +0000 (11:23 +0300)]
ALSA: fm801: precedence bug in snd_fm801_tea575x_get_pins()
There is a precedence bug because | has higher precedence than ?:. This
code was cut and pasted and I fixed a similar bug a few days ago.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alexander Duyck [Tue, 13 Nov 2012 13:10:59 +0000 (13:10 +0000)]
vxlan: Update hard_header_len based on lowerdev when instantiating VXLAN
In the event of a VXLAN device being linked to a device that has a
hard_header_len greater than that of standard ethernet we could end up with
the hard_header_len not being large enough for outgoing frames. In order to
prevent this we should update the length when a lowerdev is provided.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rami Rosen [Tue, 13 Nov 2012 13:29:15 +0000 (13:29 +0000)]
vxlan: fix a typo.
Use eXtensible and not eXtensiable in the comment on top.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Tue, 13 Nov 2012 21:27:19 +0000 (22:27 +0100)]
i2c-mux-pinctrl: Fix probe error path
When allocating the memory for i2c busses, the code checked the wrong
variable and thus never detected if there was a memory error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Tue, 13 Nov 2012 21:27:19 +0000 (22:27 +0100)]
MAINTAINERS: i2c: 7 years, this is it
I have been maintaining the i2c subsystem for 7 years now, it's about
time to let someone else take over. Just before I leave, I would like
to thank several individuals who made this possible at all:
* Greg Kroah-Hartman, for his faith in my potential subsystem
maintainer skills. Greg, I hope I met your expectations.
* Late David Brownell, for helping me convert the i2c subsystem to the
standard device driver model. Rest in peace David, we're missing you.
* Ben Dooks, for stepping in when I asked for someone to take care of
the huge flow of new i2c adapter drivers for embedded systems.
* Wolfram Sang, for joining the crew when it became clear that there
was more review work than Ben and myself could deal with.
I hope I did not forget anyone, please forgive me if I did.
Another big thank is due to Wolfram again, who quickly proposed to
take over as the main i2c subsystem maintainer. This will allow for a
smooth and fast transition.
Note that I will keep maintaining all I2C/SMBus controller drivers for
PC systems as well as a few others. I am hereby updating MAINTAINERS
accordingly. I'll also keep maintaining user-space i2c-tools.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Colin Cross [Thu, 8 Nov 2012 02:21:51 +0000 (18:21 -0800)]
Revert "Staging: Android alarm: IOCTL command encoding fix"
Commit
6bd4a5d96c08dc2380f8053b1bd4f879f55cd3c9 changed the
ANDROID_ALARM_GET_TIME ioctls from IOW to IOR. While technically
correct, the _IOC_DIR bits are ignored by alarm_ioctl, so the
commit breaks a userspace ABI used by all existing Android devices
for a purely cosmetic reason. Revert it.
Cc: stable <stable@vger.kernel.org>
Cc: Dae S. Kim <dae@velatum.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hannes Frederic Sowa [Sat, 10 Nov 2012 19:52:34 +0000 (19:52 +0000)]
ipv6: setsockopt(IPIPPROTO_IPV6, IPV6_MINHOPCOUNT) forgot to set return value
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill Smelkov [Sat, 10 Nov 2012 07:12:36 +0000 (07:12 +0000)]
doc/net: Fix typo in netdev-features.txt
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 9 Nov 2012 13:35:24 +0000 (13:35 +0000)]
vxlan: Fix error that was resulting in VXLAN MTU size being 10 bytes too large
This change fixes an issue I found where VXLAN frames were fragmented when
they were up to the VXLAN MTU size. I root caused the issue to the fact that
the headroom was 4 + 20 + 8 + 8. This math doesn't appear to be correct
because we are not inserting a VLAN header, but instead a 2nd Ethernet header.
As such the math for the overhead should be 20 + 8 + 8 + 14 to account for the
extra headers that are inserted for VXLAN.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 13 Nov 2012 05:37:18 +0000 (05:37 +0000)]
tcp: tcp_replace_ts_recent() should not be called from tcp_validate_incoming()
We added support for RFC 5961 in latest kernels but TCP fails
to perform exhaustive check of ACK sequence.
We can update our view of peer tsval from a frame that is
later discarded by tcp_ack()
This makes timestamps enabled sessions vulnerable to injection of
a high tsval : peers start an ACK storm, since the victim
sends a dupack each time it receives an ACK from the other peer.
As tcp_validate_incoming() is called before tcp_ack(), we should
not peform tcp_replace_ts_recent() from it, and let callers do it
at the right time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Romain Francoise <romain@orebokech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Tue, 13 Nov 2012 03:19:43 +0000 (03:19 +0000)]
net: cdc_ncm: add Huawei devices
A number of Huawei 3G and LTE modems implement a CDC NCM function,
including the necessary functional descriptors, but using a non
standard interface layout and class/subclass/protocol codes.
These devices can be handled by this driver with only a minor
change to the probing logic, allowing a single combined control
and data interface. This works because the devices
- include a CDC Union descriptor labelling the combined
interface as both master and slave, and
- have an alternate setting #1 for the bulk endpoints on the
combined interface.
The 3G/LTE network connection is managed by vendor specific AT
commands on a serial function in the same composite device.
Handling the managment function is out of the scope of this
driver. It will be handled by an appropriate USB serial
driver.
Reported-and-Tested-by: Olof Ermis <olof.ermis@gmail.com>
Reported-and-Tested-by: Tommy Cheng <tommy7765@yahoo.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 12 Nov 2012 23:05:17 +0000 (23:05 +0000)]
qeth: set new mac even if old mac is gone
If the set_mac_address() function of qeth is invoked, qeth deletes
the old mac address first on OSA. Only if deletion returns
successfully the new mac address is set on OSA. Deletion may return
with a return value "MAC not found on OSA". In this case qeth
should continue setting the new mac address.
When the OSA cable is pulled, OSA forgets any set mac address. If
the OSA network interface acts as a slave to a bonding master
interface, bonding can invoke the set_mac_address function for
failover purposes and depends on successful setting of the new mac
address even though the old mac address could no longer be deleted.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 12 Nov 2012 23:05:16 +0000 (23:05 +0000)]
qeth: Fix IPA_CMD_QIPASSIST return code handling
Return codes of IPA_CMD_QIPASSIST are not checked, especially the ones which
indicate that the command is not supported. As a result, the device driver
would not enable all available features on older card generations.
This patch adds proper checking and sets the bare minimum in the supported
functions flags to avoid follow-on errors.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Glendinning [Tue, 6 Nov 2012 00:08:53 +0000 (00:08 +0000)]
smsc95xx: set MII_BUSY bit to read/write PHY regs
The device datasheet specifies the BUSY bit must be set when reading
or writing phy registers. This patch ensures we do that.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Tue, 13 Nov 2012 18:52:52 +0000 (10:52 -0800)]
Revert "USB/host: Cleanup unneccessary irq disable code"
This reverts commit
73d4066055e0e2830533041f4b91df8e6e5976ff.
Martin Steigerwald reported that this change caused a hard lockup when
using USB if threadirqs are enabled. Thomas pointed out that this patch
is incorrect, and can cause problems. So revert it to get the
previously working functionality back.
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams [Thu, 8 Nov 2012 17:56:53 +0000 (11:56 -0600)]
USB: option: add Alcatel X220/X500D USB IDs
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams [Thu, 8 Nov 2012 17:56:42 +0000 (11:56 -0600)]
USB: option: add Novatel E362 and Dell Wireless 5800 USB IDs
The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>