OSDN Git Service
Sylwia Wnuczko [Tue, 23 Jul 2019 10:01:43 +0000 (06:01 -0400)]
i40e: Persistent LLDP support
This patch adds a function to read NVM module data and uses it to
read current LLDP agent configuration from NVM API version 1.8.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Piotr Kwapulinski [Tue, 23 Jul 2019 10:01:41 +0000 (06:01 -0400)]
i40e: allow reset in recovery mode
Driver waits after issuing a reset. When a reset takes too long a driver
gives up. Implemented by invoking PF reset in a loop. After defined
number of unsuccessful PF reset trials it returns error.
Without this patch PF reset fails when NIC is in recovery mode.
So make i40e_set_mac_type() public. i40e driver requires i40e_set_mac_type()
to be public. It is required for recovery mode handling. Without this patch
recovery mode could not be detected in i40e_probe().
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Grzegorz Siwik [Tue, 23 Jul 2019 10:01:40 +0000 (06:01 -0400)]
i40e: Remove function i40e_update_dcb_config()
This patch removes function i40e_update_dcb_config(). Instead of
i40e_update_dcb_config() we use i40e_init_dcb(), which implements the
correct NVM read.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Slawomir Laba [Tue, 23 Jul 2019 10:01:39 +0000 (06:01 -0400)]
i40e: Fix crash caused by stress setting of VF MAC addresses
Add update to the VSI pointer passed to the i40e_set_vf_mac function.
If VF is in reset state the driver waits in i40e_set_vf_mac function
for the reset to be complete, yet after reset the vsi pointer
that was passed into this function is no longer valid.
The patch updates local VSI pointer directly from pf->vsi array,
by using the id stored in VF pointer (lan_vsi_idx).
Without this commit the driver might occasionally invoke general
protection fault in kernel and disable the OS entirely.
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 23 Jul 2019 10:01:37 +0000 (06:01 -0400)]
i40e: reset veb.tc_stats when resetting veb.stats
The stats structure for the VEB switch statistics is reset periodically,
but the tc_stats are not reset at the same time.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Piotr Azarewicz [Tue, 23 Jul 2019 10:01:36 +0000 (06:01 -0400)]
i40e: Update FW API version to 1.9
Upcoming FW increment API version to 1.9 due to Extend PHY access AQ
command support. SW is ready for that support as well.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adrian Podlawski [Tue, 23 Jul 2019 10:01:35 +0000 (06:01 -0400)]
i40e: check_recovery_mode had wrong if statement
Function check_recovery_mode had wrong if statement.
Now we check proper FWS1B register values, which are responsible for
the recovery mode. Recovery mode has 4 values for x710 and 2 for x722.
That's why we need 6 different flags which are defined in the code.
Now in the if statement, we recognize type of mac address
and register value.
Without those changes driver could show wrong state.
Signed-off-by: Adrian Podlawski <adrian.podlawski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sylwia Wnuczko [Tue, 23 Jul 2019 10:01:34 +0000 (06:01 -0400)]
i40e: Add drop mode parameter to set mac config
This patch adds "drop mode" parameter to set mac config AQ command.
This bit controls the behavior when a no-drop packet is blocking a TC
queue.
0 – The PF driver is notified.
1 – The blocking packet is dropped and then the PF driver is notified.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Beilei Xing [Tue, 23 Jul 2019 10:01:33 +0000 (06:01 -0400)]
i40e: fix shifts of signed values
This patch fixes following error reported by cppcheck:
(error) Shifting signed 32-bit value by 31 bits is undefined behaviour
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
huhai [Mon, 22 Jul 2019 11:55:59 +0000 (19:55 +0800)]
i40e: add check on i40e_configure_tx_ring() return value
When i40e_configure_tx_ring(vsi->tx_rings[i]) returns an error, we should
exit from i40e_vsi_configure_tx and return the error, instead of continuing
to check whether xdp is enable, and configure the xdp transmit ring.
Signed-off-by: huhai <huhai@kylinos.cn>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mauro S. M. Rodrigues [Thu, 18 Jul 2019 17:52:02 +0000 (14:52 -0300)]
i40e: Check if transceiver implements DDM before access
Similar to the ixgbe issue fixed in:
655c91414579 ("ixgbe: Check DDM existence in transceiver before access)
i40e has the same issue when reading eeprom from SFP's module that comply
with SFF-8472 but not implement the Digital Diagnostic Monitoring (DDM)
interface described in it. The existence of such area is specified by bit
6 of byte 92, set to 1 if implemented.
Without this patch, due to not checking this bit i40e fails to read SFP
module's eeprom with the follow message:
ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Arnd Bergmann [Mon, 15 Jul 2019 12:35:07 +0000 (14:35 +0200)]
i40e: reduce stack usage in i40e_set_fc
The functions i40e_aq_get_phy_abilities_resp() and i40e_set_fc() both
have giant structure on the stack, which makes each one use stack frames
larger than 500 bytes.
As clang decides one function into the other, we get a warning for
exceeding the frame size limit on 32-bit architectures:
drivers/net/ethernet/intel/i40e/i40e_common.c:1654:23: error: stack frame size of 1116 bytes in function 'i40e_set_fc' [-Werror,-Wframe-larger-than=]
When building with gcc, the inlining does not happen, but i40e_set_fc()
calls i40e_aq_get_phy_abilities_resp() anyway, so they add up on the
kernel stack just as much.
The parts that actually use large stacks don't overlap, so make sure
each one is a separate function, and mark them as noinline_for_stack to
prevent the compilers from combining them again.
Fixes:
0a862b43acc6 ("i40e/i40evf: Add module_types and update_link_info")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Colin Ian King [Thu, 22 Aug 2019 12:53:40 +0000 (13:53 +0100)]
nexthops: remove redundant assignment to variable err
Variable err is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused Value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Aug 2019 07:25:12 +0000 (00:25 -0700)]
Merge branch 'mlx5-hyperv'
Haiyang Zhang says:
====================
Add software backchannel and mlx5e HV VHCA stats
This patch set adds paravirtual backchannel in software in pci_hyperv,
which is required by the mlx5e driver HV VHCA stats agent.
The stats agent is responsible on running a periodic rx/tx packets/bytes
stats update.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Thu, 22 Aug 2019 05:06:00 +0000 (05:06 +0000)]
net/mlx5e: Add mlx5e HV VHCA stats agent
HV VHCA stats agent is responsible on running a preiodic rx/tx
packets/bytes stats update. Currently the supported format is version
MLX5_HV_VHCA_STATS_VERSION. Block ID 1 is dedicated for statistics data
transfer from the VF to the PF.
The reporter fetch the statistics data from all opened channels, fill it
in a buffer and send it to mlx5_hv_vhca_write_agent.
As the stats layer should include some metadata per block (sequence and
offset), the HV VHCA layer shall modify the buffer before actually send it
over block 1.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Thu, 22 Aug 2019 05:05:56 +0000 (05:05 +0000)]
net/mlx5: Add HV VHCA control agent
Control agent is responsible over of the control block (ID 0). It should
update the PF via this block about every capability change. In addition,
upon block 0 invalidate, it should activate all other supported agents
with data requests from the PF.
Upon agent create/destroy, the invalidate callback of the control agent
is being called in order to update the PF driver about this change.
The control agent is an integral part of HV VHCA and will be created
and destroy as part of the HV VHCA init/cleanup flow.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Thu, 22 Aug 2019 05:05:51 +0000 (05:05 +0000)]
net/mlx5: Add HV VHCA infrastructure
HV VHCA is a layer which provides PF to VF communication channel based on
HyperV PCI config channel. It implements Mellanox's Inter VHCA control
communication protocol. The protocol contains control block in order to
pass messages between the PF and VF drivers, and data blocks in order to
pass actual data.
The infrastructure is agent based. Each agent will be responsible of
contiguous buffer blocks in the VHCA config space. This infrastructure will
bind agents to their blocks, and those agents can only access read/write
the buffer blocks assigned to them. Each agent will provide three
callbacks (control, invalidate, cleanup). Control will be invoked when
block-0 is invalidated with a command that concerns this agent. Invalidate
callback will be invoked if one of the blocks assigned to this agent was
invalidated. Cleanup will be invoked before the agent is being freed in
order to clean all of its open resources or deferred works.
Block-0 serves as the control block. All execution commands from the PF
will be written by the PF over this block. VF will ack on those by
writing on block-0 as well. Its format is described by struct
mlx5_hv_vhca_control_block layout.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Thu, 22 Aug 2019 05:05:47 +0000 (05:05 +0000)]
net/mlx5: Add wrappers for HyperV PCIe operations
Add wrapper functions for HyperV PCIe read / write /
block_invalidate_register operations. This will be used as an
infrastructure in the downstream patch for software communication.
This will be enabled by default if CONFIG_PCI_HYPERV_INTERFACE is set.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Thu, 22 Aug 2019 05:05:41 +0000 (05:05 +0000)]
PCI: hv: Add a Hyper-V PCI interface driver for software backchannel interface
This interface driver is a helper driver allows other drivers to
have a common interface with the Hyper-V PCI frontend driver.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dexuan Cui [Thu, 22 Aug 2019 05:05:37 +0000 (05:05 +0000)]
PCI: hv: Add a paravirtual backchannel in software
Windows SR-IOV provides a backchannel mechanism in software for communication
between a VF driver and a PF driver. These "configuration blocks" are
similar in concept to PCI configuration space, but instead of doing reads and
writes in 32-bit chunks through a very slow path, packets of up to 128 bytes
can be sent or received asynchronously.
Nearly every SR-IOV device contains just such a communications channel in
hardware, so using this one in software is usually optional. Using the
software channel, however, allows driver implementers to leverage software
tools that fuzz the communications channel looking for vulnerabilities.
The usage model for these packets puts the responsibility for reading or
writing on the VF driver. The VF driver sends a read or a write packet,
indicating which "block" is being referred to by number.
If the PF driver wishes to initiate communication, it can "invalidate" one or
more of the first 64 blocks. This invalidation is delivered via a callback
supplied by the VF driver by this driver.
No protocol is implied, except that supplied by the PF and VF drivers.
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 22 Aug 2019 03:23:29 +0000 (20:23 -0700)]
Merge tag 'mlx5-updates-2019-08-21' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 tc flow handling for concurrent execution (Part 3)
This series includes updates to mlx5 ethernet and core driver:
Vlad submits part 3 of 3 part series to allow TC flow handling
for concurrent execution.
Vlad says:
==========
Structure mlx5e_neigh_hash_entry code that uses it are refactored in
following ways:
- Extend neigh_hash_entry with rcu and modify its users to always take
reference to the structure when using it (neigh_hash_entry has already
had atomic reference counter which was only used when scheduling neigh
update on workqueue from atomic context of neigh update netevent).
- Always use mlx5e_neigh_update_table->encap_lock when modifying neigh
update hash table and list. Originally, this lock was only used to
synchronize with netevent handler function, which is called from bh
context and cannot use rtnl lock for synchronization. Use rcu read lock
instead of encap_lock to lookup nhe in atomic context of netevent even
handler function. Convert encap_lock to mutex to allow creating new
neigh hash entries while holding it, which is safe to do because the
lock is no longer used in atomic context.
- Rcu-ify mlx5e_neigh_hash_entry->encap_list by changing operations on
encap list to their rcu counterparts and extending encap structure
with rcu_head to free the encap instances after rcu grace period. This
allows fast traversal of list of encaps attached to nhe under rcu read
lock protection.
- Take encap_table_lock when accessing encap entries in neigh update and
neigh stats update code to protect from concurrent encap entry
insertion or removal.
This approach leads to potential race condition when neigh update and
neigh stats update code can access encap and flow entries that are not
fully initialized or are being destroyed, or neigh can change state
without updating encaps that are created concurrently. Prevent these
issues by following changes in flow and encap initialization:
- Extend mlx5e_tc_flow with 'init_done' completion. Modify neigh update
to wait for both encap and flow completions to prevent concurrent
access to a structure that is being initialized by tc.
- Skip structures that failed during initialization: encaps with
encap_id<0 and flows that don't have OFFLOADED flag set.
- To ensure that no new flows are added to encap when it is being
accessed by neigh update or neigh stats update, take encap_table_lock
mutex.
- To prevent concurrent deletion by tc, ensure that neigh update and
neigh stats update hold references to encap and flow instances while
using them.
With changes presented in this patch set it is now safe to execute tc
concurrently with neigh update and neigh stats update. However, these
two workqueue tasks modify same flow "tmp_list" field to store flows
with reference taken in temporary list to release the references after
update operation finishes and should not be executed concurrently with
each other.
Last 3 patches of this series provide 3 new mlx5 trace points to track
mlx5 tc requests and mlx5 neigh updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Tue, 25 Jun 2019 19:40:20 +0000 (22:40 +0300)]
net/mlx5e: Add trace point for neigh update
Allow tracing neigh state during neigh update task that is executed on
workqueue and is scheduled by neigh state change event.
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5e_rep_neigh_update >> set_event
># cat trace
...
kworker/u48:7-2221 [009] ...1 1475.387435: mlx5e_rep_neigh_update:
netdev: ens1f0 MAC: 24:8a:07:9a:17:9a IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_connected=1
Added corresponding documentation in
Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Tue, 25 Jun 2019 19:33:15 +0000 (22:33 +0300)]
net/mlx5e: Add trace point for neigh used value update
Allow tracing result of neigh used value update task that is executed
periodically on workqueue.
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5e_tc_update_neigh_used_value >> set_event
># cat trace
...
kworker/u48:4-8806 [009] ...1 55117.882428: mlx5e_tc_update_neigh_used_value:
netdev: ens1f0 IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_used=1
Added corresponding documentation in
Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Dmytro Linkin [Thu, 27 Jun 2019 10:55:02 +0000 (10:55 +0000)]
net/mlx5e: Add tc flower tracepoints
Implemented following tracepoints:
1. Configure flower (mlx5e_configure_flower)
2. Delete flower (mlx5e_delete_flower)
3. Stats flower (mlx5e_stats_flower)
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5e_configure_flower >> set_event
># cat trace
...
tc-6535 [019] ...1 2672.404466: mlx5e_configure_flower: cookie=
0000000067874a55 actions= REDIRECT
Added corresponding documentation in
Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Sun, 4 Aug 2019 10:52:31 +0000 (13:52 +0300)]
net/mlx5e: Only access fully initialized flows in neigh update
To remove dependency on rtnl lock and prevent neigh update code from
accessing uninitialized flows when executing concurrently with tc, extend
mlx5e_tc_flow with 'init_done' completion. Modify helper
mlx5e_take_all_encap_flows() to wait for flow completion after obtaining
reference to it. Modify mlx5e_tc_encap_flows_del() and
mlx5e_tc_encap_flows_add() to skip flows that don't have OFFLOADED flag
set, which can happen if concurrent flow initialization failed.
This commit finishes neigh update refactoring for concurrent execution
started in previous change in this series.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Sun, 4 Aug 2019 09:25:57 +0000 (12:25 +0300)]
net/mlx5e: Refactor neigh update for concurrent execution
In order to remove dependency on rtnl lock and allow neigh update workqueue
task to execute concurrently with tc, refactor mlx5e_rep_neigh_update() for
concurrent execution:
- Lock encap table when accessing encap entry to prevent concurrent
changes. To do this properly, the initial encap state check is moved from
mlx5e_rep_neigh_update() into mlx5e_rep_update_flows() to be performed
under encap_tbl_lock protection.
- Wait for encap to be fully initialized before accessing it by means of
'res_ready' completion.
- Add mlx5e_take_all_encap_flows() helper which is used to construct a
temporary list of flows and efi indexes that is used to access current
encap data in flow which can be attached to multiple encaps
simultaneously. Release the flows from temporary list after
encap_tbl_lock critical section. This is necessary because
mlx5e_flow_put() can't be called while holding encap_tbl_lock.
- Modify mlx5e_tc_encap_flows_add() and mlx5e_tc_encap_flows_del() to work
with user-provided list of flows built by mlx5e_take_all_encap_flows(),
instead of traversing encap flow list directly.
This is first step in complex neigh update refactoring, which is finished
by following commit in this series.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Sat, 3 Aug 2019 18:43:06 +0000 (21:43 +0300)]
net/mlx5e: Refactor neigh used value update for concurrent execution
In order to remove dependency on rtnl lock and allow neigh used value
update workqueue task to execute concurrently with tc, refactor
mlx5e_tc_update_neigh_used_value() for concurrent execution:
- Lock encap table when accessing encap entry to prevent concurrent
changes.
- Save offloaded encap flows to temporary list and release them after encap
entry is updated. Add mlx5e_put_encap_flow_list() helper which is
intended to be shared with neigh update code in following patch in this
series. This is necessary because mlx5e_flow_put() can't be called while
holding encap_tbl_lock.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Mon, 11 Jun 2018 11:16:14 +0000 (14:16 +0300)]
net/mlx5e: Protect neigh hash encap list with spinlock and rcu
Rcu-ify mlx5e_neigh_hash_entry->encap_list by changing operations on encap
list to their rcu counterparts and extending encap structure with rcu_head
to free the encap instances after rcu grace period. Use rcu read lock when
traversing encap list. Implement helper mlx5e_get_next_valid_encap()
function that is used by mlx5e_tc_update_neigh_used_value() to safely
iterate over valid entries of nhe->encap_list.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Tue, 12 Jun 2018 08:59:43 +0000 (11:59 +0300)]
net/mlx5e: Refactor mlx5e_neigh_update_table->encap_lock
To remove dependency on rtnl lock, always take neigh update encap lock when
modifying neigh update hash table and list. Originally, this lock was only
used to synchronize with netevent handler function, which is called from bh
context and cannot use rtnl lock for synchronization. Take lock in encap
entry attach function to prevent concurrent modifications of neigh update
hash table and list.
Taking the encap lock when creating new nhe introduces a problem that we
need to allocate new entry with sleeping GFP_KERNEL flag while holding a
spinlock. However, since previous patch in this series has already
converted lookup in netevent handler function to user rcu read lock instead
of encap lock, we can safely convert the lock type to mutex.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Fri, 8 Jun 2018 08:49:28 +0000 (11:49 +0300)]
net/mlx5e: Extend neigh hash entry with rcu
To remove dependency on rtnl lock and to allow unlocked iteration over list
of neigh hash entries, extend nhe with rcu. Change operations on neigh list
to their rcu counterparts and free neigh hash entry with rcu timeout.
Introduce mlx5e_get_next_nhe() helper that is used to iterate over rcu
neigh list with reference to nhe taken.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Fri, 8 Jun 2018 08:31:28 +0000 (11:31 +0300)]
net/mlx5e: Always take reference to neigh entry
Neigh entry has reference counter, however it is only used when scheduling
neigh update event. In all other cases reference to neigh entry is not
taken while working with it. Neigh code relies on synchronization provided
by rtnl lock and uses encap list size as implicit reference counter.
To remove dependency on rtnl lock, always take reference to neigh entry
while using it. Remove neigh entry from hash table and delete it only when
reference counter reaches zero. This can result spurious neigh update
events, when there is an event on entry that has zero encaps attached.
However, such events are rare and properly handled by neigh update handler.
Extend encap entry with reference to neigh hash entry in order to be able
to directly release it when encap is detached, instead of lookup nhe by key
through hash table. Extend nhe with reference to device priv structure to
guarantee correctness when nhe is used with stack devices, bond setup, in
which case it is non-trivial to determine correct device when releasing the
nhe.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Wed, 13 Jun 2018 11:49:46 +0000 (14:49 +0300)]
net/mlx5e: Extract code that queues neigh update work into function
As a preparation for following refactoring that removes rtnl lock
dependency from neigh hash entry handlers, extract code that enqueues neigh
update work into standalone function. This commit doesn't change
functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
YueHaibing [Wed, 21 Aug 2019 13:57:01 +0000 (21:57 +0800)]
net: stmmac: dwc-qos: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:55:50 +0000 (21:55 +0800)]
net: stmmac: dwmac-anarion: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:54:06 +0000 (21:54 +0800)]
net: stmmac: dwmac-meson: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:51:30 +0000 (21:51 +0800)]
net: stmmac: dwmac-meson8b: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:46:13 +0000 (21:46 +0800)]
net: systemport: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:41:31 +0000 (21:41 +0800)]
net: bcmgenet: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:38:54 +0000 (21:38 +0800)]
pxa168_eth: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:33:02 +0000 (21:33 +0800)]
net: mvneta: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:29:45 +0000 (21:29 +0800)]
net: fec: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:05:09 +0000 (21:05 +0800)]
ezchip: nps_enet: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 13:02:41 +0000 (21:02 +0800)]
cirrus: cs89x0: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 12:59:59 +0000 (20:59 +0800)]
net: sxgbe: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 12:58:11 +0000 (20:58 +0800)]
net: ks8851-ml: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 12:53:57 +0000 (20:53 +0800)]
net: socionext: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 12:50:50 +0000 (20:50 +0800)]
via-rhine: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 12:48:50 +0000 (20:48 +0800)]
net: ethernet: ti: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 21 Aug 2019 12:32:03 +0000 (20:32 +0800)]
amd-xgbe: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Aug 2019 20:02:32 +0000 (13:02 -0700)]
Merge tag 'mac80211-next-for-davem-2019-08-21' of git://git./linux/kernel/git/jberg/mac80211-next
Johannes Berg:
====================
Here are a few groups of changes:
* EDMG channel support (60 GHz, just a single patch)
* initial 6/7 GHz band support (Arend)
* association timestamp recording (Ben)
* rate control improvements for better performance with
the mt76 driver (Felix)
* various fixes for previous HE support changes (John)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Aug 2019 19:58:39 +0000 (12:58 -0700)]
Merge branch 'mlxsw-Add-devlink-trap-support'
Ido Schimmel says:
====================
mlxsw: Add devlink-trap support
This patchset adds devlink-trap support in mlxsw.
Patches #1-#4 add the necessary APIs and defines in mlxsw.
Patch #5 implements devlink-trap support for layer 2 drops. More drops
will be added in the future.
Patches #6-#7 add selftests to make sure that all the new code paths are
exercised and that the feature is working as expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 21 Aug 2019 07:19:37 +0000 (10:19 +0300)]
selftests: mlxsw: Add a test case for devlink-trap
Test generic devlink-trap functionality over mlxsw. These tests are not
specific to a single trap, but do not check the devlink-trap common
infrastructure either.
Currently, the only test case is device deletion (by reloading the
driver) while packets are being trapped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 21 Aug 2019 07:19:36 +0000 (10:19 +0300)]
selftests: mlxsw: Add test cases for devlink-trap L2 drops
Test that each supported packet trap is triggered under the right
conditions and that packets are indeed dropped and not forwarded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 21 Aug 2019 07:19:35 +0000 (10:19 +0300)]
mlxsw: spectrum: Add devlink-trap support
Register supported packet traps (layer 2 drops only, currently) and
associated trap group with devlink during driver initialization.
The amount of traffic generated by these packet drop traps is capped at
10Kpps to ensure the CPU is not overwhelmed by incoming packets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 21 Aug 2019 07:19:34 +0000 (10:19 +0300)]
mlxsw: Add trap group for layer 2 discards
Discard trap groups are defined in a different enum so that they could
all share the same policer ID: MLXSW_REG_HTGT_TRAP_GROUP_MAX + 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 21 Aug 2019 07:19:33 +0000 (10:19 +0300)]
mlxsw: Add layer 2 discard trap IDs
Add the trap IDs used to report layer 2 drops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 21 Aug 2019 07:19:32 +0000 (10:19 +0300)]
mlxsw: reg: Add new trap actions
Subsequent patches will add discard traps support in mlxsw. The driver
cannot configure such traps with a normal trap action, but needs to use
exception trap action, which also increments an error counter.
On the other hand, when these traps are initialized or set to drop
action, they should use the default drop action set by the firmware.
This guarantees that when the feature is disabled we get the exact same
behavior as before the feature was introduced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 21 Aug 2019 07:19:31 +0000 (10:19 +0300)]
mlxsw: core: Add API to set trap action
Up until now the action of a trap was never changed during its lifetime.
This is going to change by subsequent patches that will allow devlink to
control the action of certain traps.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Tue, 20 Aug 2019 09:54:49 +0000 (11:54 +0200)]
mac80211: minstrel_ht: improve rate probing for devices with static fallback
On some devices that only support static rate fallback tables sending rate
control probing packets can be really expensive.
Probing lower rates can already hurt throughput quite a bit. What hurts even
more is the fact that on mt76x0/mt76x2, single probing packets can only be
forced by directing packets at a different internal hardware queue, which
causes some heavy reordering and extra latency.
The reordering issue is mainly problematic while pushing lots of packets to
a particular station. If there is little activity, the overhead of probing is
neglegible.
The static fallback behavior is designed to pretty much only handle rate
control algorithms that use only a very limited set of rates on which the
algorithm switches up/down based on packet error rate.
In order to better support that kind of hardware, this patch implements a
different approach to rate probing where it switches to a slightly higher rate,
waits for tx status feedback, then updates the stats and switches back to
the new max throughput rate. This only triggers above a packet rate of 100
per stats interval (~50ms).
For that kind of probing, the code has to reduce the set of probing rates
a lot more compared to single packet probing, so it uses only one packet
per MCS group which is either slightly faster, or as close as possible to
the max throughput rate.
This allows switching between similar rates with different numbers of
streams. The algorithm assumes that the hardware will work its way lower
within an MCS group in case of retransmissions, so that lower rates don't
have to be probed by the high packets per second rate probing code.
To further reduce the search space, it also does not probe rates with lower
channel bandwidth than the max throughput rate.
At the moment, these changes will only affect mt76x0/mt76x2.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 20 Aug 2019 09:54:48 +0000 (11:54 +0200)]
mac80211: minstrel_ht: fix default max throughput rate indexes
Use the first supported rate instead of 0 (which can be invalid)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 20 Aug 2019 09:54:47 +0000 (11:54 +0200)]
mac80211: minstrel_ht: reduce unnecessary rate probing attempts
On hardware with static fallback tables (e.g. mt76x2), rate probing attempts
can be very expensive.
On such devices, avoid sampling rates slower than the per-group max throughput
rate, based on the assumption that the fallback table will take care of probing
lower rates within that group if the higher rates fail.
To further reduce unnecessary probing attempts, skip duplicate attempts on
rates slower than the max throughput rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 20 Aug 2019 09:54:46 +0000 (11:54 +0200)]
mac80211: minstrel_ht: fix per-group max throughput rate initialization
The group number needs to be multiplied by the number of rates per group
to get the full rate index
Fixes:
5935839ad735 ("mac80211: improve minstrel_ht rate sorting by throughput & probability")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexei Avshalom Lazar [Sun, 18 Aug 2019 14:35:17 +0000 (17:35 +0300)]
nl80211: Add support for EDMG channels
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John Crispin [Tue, 13 Aug 2019 07:07:12 +0000 (09:07 +0200)]
mac80211: fix possible NULL pointerderef in obss pd code
he_spr_ie_elem is dereferenced before the NULL check. fix this by moving
the assignment after the check.
fixes commit
697f6c507c74 ("mac80211: propagate HE operation info into
bss_conf")
This was reported by the static code checker.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190813070712.25509-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Greear [Fri, 9 Aug 2019 18:00:01 +0000 (11:00 -0700)]
mac80211: add assoc-at support
Report timestamp for when sta becomes associated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-2-greearb@candelatech.com
[fix ktime_get_boot_ns() to ktime_get_boottime_ns(), assoc_at type to u64]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Greear [Fri, 9 Aug 2019 18:00:00 +0000 (11:00 -0700)]
cfg80211: Support assoc-at timer in sta-info
Report timestamp of when sta became associated.
This is the boottime clock, units are nano-seconds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 2 Aug 2019 11:31:05 +0000 (13:31 +0200)]
cfg80211: apply same mandatory rate flags for 5GHz and 6GHz
For the new 6GHz band the same rules apply for mandatory rates so
add it to set_mandatory_flags_band() function.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-9-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 2 Aug 2019 11:31:04 +0000 (13:31 +0200)]
cfg80211: ibss: use 11a mandatory rates for 6GHz band operation
The default mandatory rates, ie. when not specified by user-space, is
determined by the band. Select 11a rateset for 6GHz band.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-8-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 2 Aug 2019 11:31:03 +0000 (13:31 +0200)]
cfg80211: use same IR permissive rules for 6GHz band
The function cfg80211_ir_permissive_chan() is applicable for
6GHz band as well so make sure it is handled.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-7-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 2 Aug 2019 11:31:02 +0000 (13:31 +0200)]
cfg80211: add 6GHz in code handling array with NUM_NL80211_BANDS entries
In nl80211.c there is a policy for all bands in NUM_NL80211_BANDS and
in trace.h there is a callback trace for multicast rates which is per
band in NUM_NL80211_BANDS. Both need to be extended for the new
NL80211_BAND_6GHZ.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-6-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 2 Aug 2019 11:31:01 +0000 (13:31 +0200)]
cfg80211: extend ieee80211_operating_class_to_band() for 6GHz
Add 6GHz operating class range as defined in 802.11ax D4.1 Annex E.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-5-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 2 Aug 2019 11:31:00 +0000 (13:31 +0200)]
cfg80211: util: add 6GHz channel to freq conversion and vice versa
Extend the functions ieee80211_channel_to_frequency() and
ieee80211_frequency_to_channel() to support 6GHz band according
specification in 802.11ax D4.1 27.3.22.2.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-4-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 2 Aug 2019 11:30:59 +0000 (13:30 +0200)]
cfg80211: add 6GHz UNII band definitions
For the new 6GHz there are new UNII band definitions as listed
in the FCC notice [1].
[1] https://docs.fcc.gov/public/attachments/FCC-18-147A1_Rcd.pdf
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-3-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Fri, 2 Aug 2019 11:30:58 +0000 (13:30 +0200)]
nl80211: add 6GHz band definition to enum nl80211_band
In the 802.11ax specification a new band is introduced, which
is also proposed by FCC for unlicensed use. This band is referred
to as 6GHz spanning frequency range from 5925 to 7125 MHz.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-2-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John Crispin [Wed, 7 Aug 2019 07:59:49 +0000 (09:59 +0200)]
mac80211: add missing length field increment when generating Radiotap header
The code generating the Tx Radiotap header when using tx_status_ext was
missing a field increment after setting the VHT bandwidth.
Fixes:
3d07ffcaf320 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-4-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John Crispin [Wed, 7 Aug 2019 07:59:48 +0000 (09:59 +0200)]
mac80211: 80Mhz was not reported properly when using tx_status_ext
When reporting 80MHz, we need to set 4 and not 2 inside the corresponding
field inside the Tx Radiotap header.
Fixes:
3d07ffcaf320 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John Crispin [Wed, 7 Aug 2019 07:59:47 +0000 (09:59 +0200)]
mac80211: fix bad guard when reporting legacy rates
When reporting legacy rates inside the TX Radiotap header we need to split
the check between "uses tx_statua_ext" and "is legacy rate". Not doing so
would make the code drop into the !tx_status_ext path.
Fixes:
3d07ffcaf320 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John Crispin [Wed, 7 Aug 2019 07:59:46 +0000 (09:59 +0200)]
mac80211: fix TX legacy rate reporting when tx_status_ext is used
The RX Radiotap header length was not calculated properly when reporting
legacy rates using tx_status_ext.
Fixes:
3d07ffcaf320 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller [Wed, 21 Aug 2019 05:59:45 +0000 (22:59 -0700)]
Merge tag 'mlx5-updates-2019-08-15' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-08-15
This patchset introduces changes in mlx5 devlink health reporters.
The highlight of these changes is adding a new reporter: RX reporter
mlx5 RX reporter: reports and recovers from timeouts and RX completion
error.
1) Perform TX reporter cleanup. In order to maintain the
code flow as similar as possible between RX and TX reporters, start the
set with cleanup.
2) Prepare for code sharing, generalize and move shared
functionality.
3) Refactor and extend TX reporter diagnostics information
to align the TX reporter diagnostics output with the RX reporter's
diagnostics output.
4) Add helper functions Patch 11: Add RX reporter, initially
supports only the diagnostics call back.
5) Change ICOSQ (Internal Operations Send Queue) open/close flow to
avoid race between interface down and completion error recovery.
6) Introduce recovery flows for RX ring population timeout on ICOSQ,
and for completion errors on ICOSQ and on RQ (Regular receive queues).
7) Include RX reporters in mlx5 documentation.
8) Last two patches of this series, are trivial fixes for previously
submitted patches on this release cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Aug 2019 00:02:44 +0000 (17:02 -0700)]
Merge branch '100GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-08-20
This series contains updates to ice driver only.
Brett fixes the detection of a hung transmit ring by checking the
software based tail (next_to_use) to determine if there is pending work.
Updates the driver to assume that using more than one receive queue per
receive ring container is a rare case, so use unlikely() in the case
were we actually need to divide our budget for multiple queues. Fixed
an issue where the write back on ITR bit was not being set when
interrupts are disabled, which was causing only write backs when polling
only when a cache line is filled. Cleans up unnecessary wait times
during VF bring up and reset paths. Increased the mailbox size for
receive queues that are used to communicate with VFs to accommodate the
large number of VFs that the driver can support.
Akeem restructures the initialization flows for VFs, including how VFs
are configured and resources allocated to improve flows so that when we
clean up resources, we do not try to free resources that were never
allocated. Organizes code to ensure that VF specific code is located in
the SR-IOV specific file.
Paul fixes an issue when setting the pause parameter which was
incorrectly blocking users from changing receive or transmit pause
settings. Ensure register access for MSIX vector index is only done in
the PF space and not absolute device space.
Usha fixes a potential kernel hang in the DCB rebuild path when in CEE
mode, where the ETS recommended DCB configuration is not being set or
set correctly.
Mitch updates the driver to process all receive descriptors, regardless
of the size of the associated data.
Tony fixes and issue during the reset/rebuild path of a PF VSI where we
were assuming that the PF VSI was always to be enabled, which can
attempt to bring up a PF VSI on a downed interface which can lead to
various crashes.
Pawel fixes up variable definitions to match the type of data being
stored.
v2: Dropped patch 1 of the series to add ethtool support to query/add
channels on a VSI, while we re-qork the functionality to match the
ethtool expected behavior to report combined (Tx and Rx) numbers.
v3: Updated patch 4 to use kzalloc() and kfree() instead devm_kzalloc()
and devm_kfree().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Brett Creeley [Thu, 25 Jul 2019 08:55:41 +0000 (01:55 -0700)]
ice: improve print for VF's when adding/deleting MAC filters
When we fail to add/delete MAC filters in the VF, the print doesn't
distinguish between the two. Fix that by printing whether or not we
failed to add/delete the MAC filter respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pawel Kaminski [Thu, 25 Jul 2019 08:55:40 +0000 (01:55 -0700)]
ice: Change type for queue counts
These queue variables are being assigned values that are type u16.
Change the local variables to match these types. Since these
represent queue counts, they should never be negative.
Signed-off-by: Pawel Kaminski <pawel.kaminski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Akeem G Abodunrin [Thu, 25 Jul 2019 08:55:39 +0000 (01:55 -0700)]
ice: Move VF resources definition to SR-IOV specific file
In order to use some of the VF resources definition in the SR-IOV specific
virtchnl header file, this patch moves applicable code to
ice_virtchnl_pf.h file accordingly... and they should have been defined in
the destination file originally.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 25 Jul 2019 08:55:38 +0000 (01:55 -0700)]
ice: Increase size of Mailbox receive queue for many VFs
Currently we use the ICE_MBXQ_LEN for both the Mailbox send and receive
queues that are used to communicate with VFs. This is fine for the send
queue because the PF driver will lock the queue for every single send,
but for the Mailbox receive queue every VF is posting to its Mailbox
send queue and the hardware is then handing the message to the PF on its
Mailbox receive queue. This becomes a problem with many VFs because it
seems to overburden the Mailbox receive queue on the PF. Fix this by
increasing the Mailbox receive queue for the PF to 512 entries.
The number 512 was determined based on the number of VFs supported by
the device. We can have a total of 256 VFs so in the worst case this
allows the VFs to put 2 messages in the PFs Mailbox receive queue at the
same time.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 25 Jul 2019 08:55:37 +0000 (01:55 -0700)]
ice: Reduce wait times during VF bringup/reset
Currently there are a couple places where the VF is waiting too long when
checking the status of registers. This is causing the AVF driver to
spin for longer than necessary in the __IAVF_STARTUP state. Sometimes
it causes the AVF to go into the __IAVF_COMM_FAILED, which may retrigger
the __IAVF_STARTUP state. Try to reduce the chance of this happening by
removing unnecessary wait times in VF bringup/resets.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Paul Greenwalt [Thu, 25 Jul 2019 08:55:36 +0000 (01:55 -0700)]
ice: update GLINT_DYN_CTL and GLINT_VECT2FUNC register access
Register access for GLINT_DYN_CTL and GLINT_VECT2FUNC should be within
the PF space and not the absolute device space.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tony Nguyen [Thu, 25 Jul 2019 08:55:35 +0000 (01:55 -0700)]
ice: Do not always bring up PF VSI in ice_ena_vsi()
During rebuild ice_ena_vsi() is called to recover the VSI state.
This function assumes the PF VSI is always to be enabled, however,
it's possible that during reset/rebuild the interface can be
brought down. If this occurs, we can attempt to bring up the PF
VSI on a downed interface which can lead to various crashes. If
the interface is not running, do not bring up the associated VSI.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 25 Jul 2019 08:55:34 +0000 (01:55 -0700)]
ice: allow empty Rx descriptors
In some circumstances, the hardware will hand us a receive descriptor
which has no data attached, but is otherwise valid. The receive code was
improperly ignoring these descriptors, which result in an infinite loop.
To fix this, change the receive code to process all descriptors,
regardless of the size of the associated data. Add checks to the
memory-handling functions to allow for zero size.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Usha Ketineni [Thu, 25 Jul 2019 08:55:33 +0000 (01:55 -0700)]
ice: Fix kernel hang with DCB reset in CEE mode
This patch fixes the set local MIB AQ call failures in the DCB rebuild path
by setting the defaults for the ETS recommended DCB configuration. Also,
willing bits for the DCB configuration needs to be set correctly. Resets
works fine in IEEE mode as the ETS recommended DCB configuration is
populated but not in CEE mode.
Without this patch, PFR causes the kernel hang in CEE mode.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 25 Jul 2019 08:55:32 +0000 (01:55 -0700)]
ice: Set WB_ON_ITR when we don't re-enable interrupts
Currently when busy polling is enabled we aren't setting/enabling
WB_ON_ITR in the driver. This doesn't break the driver, but it does
cause issues. If we don't enable WB_ON_ITR mode we will still get
write-backs from hardware during polling when a cache line has been
filled, but if a cache line is not filled we will not get the
write-back because WB_ON_ITR is not set. Fix this by enabling
WB_ON_ITR in the driver when interrupts are disabled.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Tue, 20 Aug 2019 21:01:56 +0000 (14:01 -0700)]
Merge tag 'linux-can-next-for-5.4-
20190820' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-08-20
this is a pull request for net-next/master consisting of 18 patches.
The first patch is by Geert Uytterhoeven, it removes the unused platform
data support from the rcar_can driver.
A patch by Nishka Dasgupta marks the structure peak_pciec_i2c_bit_ops in
the peak_pci driver as constant.
A patch by me removes the custom DMA support from the hi311x driver.
The next 4 patches target the tcan4x5x driver and are also by me, they
first clean up the driver a bit, and then add missing error handling and
fix a bug in the length calculation in the regmap callbacks.
The next 2 patches are by me for the m_can_platform driver, they also
remove unneeded casts and add missing error handling.
The remaining 9 patches all target the mcp251x driver. The first 5 are
clean up patches by me, the next relaxes the timing in the
mcp251x_hw_reset() function. Alexander Shiyan's patch improves the name
which is used while registering the interrupt handler. Phil Elwell's
patch improves the mcp251x_open() function to use the DT-supplied
interrupt flags instead of hard coding them. The final patch is again by
me, it removes the custom DMA support from the hi311x driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Greenwalt [Thu, 25 Jul 2019 08:55:31 +0000 (01:55 -0700)]
ice: fix set pause param autoneg check
When ETHTOOL_GLINKSETTINGS is defined get pause param pause->autoneg
reports SW configured setting, however when not defined get pause param
pause->autoneg reports the link status. Set pause param needs to compare
pause->autoneg with the same source as get pause param to block the user
from changing autoneg with the set pause param option, or the user
may be incorrectly blocked from changing Rx|Tx pause settings.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Tue, 20 Aug 2019 20:51:46 +0000 (13:51 -0700)]
Merge branch 's390-net-next'
Julian Wiedmann says:
====================
s390/net: updates 2019-08-20
please apply the following patches to net-next. This series brings a mix
of cleanups and small improvements for various parts of qeth's control
path. Also, a minor cleanup for ctcm and lcs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Aug 2019 14:46:43 +0000 (16:46 +0200)]
s390/lcs: don't use intparm for channel IO
lcs passes an intparm when calling ccw_device_*(), even though lcs_irq()
later makes no use of this.
To reduce the confusion, consistently pass 0 as intparm instead.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Aug 2019 14:46:42 +0000 (16:46 +0200)]
s390/ctcm: don't use intparm for channel IO
ctcm passes an intparm when calling ccw_device_*(), even though
ctcm_irq_handler() later makes no use of this.
To reduce the confusion, consistently pass 0 as intparm instead.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Aug 2019 14:46:41 +0000 (16:46 +0200)]
s390/qeth: streamline control code for promisc mode
We have logic to determine the desired promisc mode in _each_ code path.
Change things around so that there is a clean split between
(a) high-level code that selects the new mode, and (b) implementations
of the various mechanisms to program this mode.
This also keeps qeth_promisc_to_bridge() from polluting the debug logs
on each RX modeset.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Aug 2019 14:46:40 +0000 (16:46 +0200)]
s390/qeth: get vnicc sub-cmd type from reply data
When processing the reply for a vnicc cmd, there's no need to remember
which specific sub-cmd type we initially sent. The reply itself contains
all the needed information.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Aug 2019 14:46:39 +0000 (16:46 +0200)]
s390/qeth: merge qeth_reply struct into qeth_cmd_buffer
Except for card->read_cmd, every cmd we issue now passes through
qeth_send_control_data() and allocates a qeth_reply struct. The way we
use this struct requires additional refcounting, and pointer tracking.
Clean up things by moving most of qeth_reply's content into the main
cmd struct. This keeps things in one place, saves us the additional
refcounting and simplifies the overall code flow.
A nice little benefit is that we can now match incoming replies against
the pending requests themselves, without caching the requests' seqnos.
The qeth_reply struct stays around for a little bit longer in a shrunk
form, to avoid touching every single callback.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Aug 2019 14:46:38 +0000 (16:46 +0200)]
s390/qeth: keep cmd alive after IO completion
Current code releases the cmd struct after its initial IO has completed.
Any reply processing is done independently, using a separate qeth_reply
struct.
In preparation for merging the cmd and reply structs together, take an
additional reference on the cmd object so that it stays around all the
way until qeth_send_control_data() returns.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 20 Aug 2019 14:46:37 +0000 (16:46 +0200)]
s390/qeth: use correct length field in SNMP cmd callback
qeth_snmp_command_cb() is the only cmd callback that pulls the reply's
data length from a low-level transport header field. This requires
additional complexity (ie. reply->offset) to make the header accessible
to what is supposed to be a pure IPA cmd callback.
Adapter cmds have a length field in their sub-cmd header, get the data
length from there instead.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>