OSDN Git Service
Serey Kong [Thu, 27 Aug 2015 15:42:41 +0000 (11:42 -0400)]
i40e/i40evf: Explicitly assign enum index for VSI type
Ran into an issue where PF's VSI type list was different from VF's,
which was resulted in different enum index. The VSI type list can
be different depending on what build flag is used for PF and VF.
The change is to explicitly assign enum index for each VSI type
so that PF and VF always reference to the same VSI type event if the
enum lists are different.
Change-ID: I8c0e5fdb515f324f7964df863a458073cf467e57
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Thu, 27 Aug 2015 15:42:40 +0000 (11:42 -0400)]
i40e: add switch for link polling
There's been some need for controlling the periodic link polling for
debugging link issues. This patch enables switching it off and on
through an ethtool private flag. The link poll remains on by default,
but can be turned off with
ethtool --set-priv-flags p261p1 LinkPolling off
and later turned back on with
ethtool --set-priv-flags p261p1 LinkPolling on
To check the current status, use
ethtool --show-priv-flags p261p1
Change-ID: I32e4ab654ff3eec90a06cf144899971b82d71c40
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matt Jared [Thu, 27 Aug 2015 15:42:39 +0000 (11:42 -0400)]
i40e: Fix multiple link up messages
This patch addresses an issue where multiple link up messages can be logged
resulting from aq link status timing when link properties are changed (fc,
speed, etc.); solved by using a single function to handle status printing
and adding a mechanism to track whether link state (up or down) has
actually changed.
Change-ID: Ied6ed6e49dc397c77d992adc0bc9ed3767152b9d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Thu, 27 Aug 2015 15:42:38 +0000 (11:42 -0400)]
i40e: Fix for extra Flow Director filter in table after error
This patch fixes a problem where the PF's fdir filter table would have an
entry that the hw was unable to add. This notification happens in the hot
path, so instead of trying to fix it then, we note the location in the
failure case and delete it during regular fdir subtask callback. Without
this patch, a case can occur where an invalid entry gets replayed and a
valid one is not.
Change-ID: I67831c183b5d0309876de807cc434809b74c9cb7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Thu, 27 Aug 2015 15:42:37 +0000 (11:42 -0400)]
i40e/i40evf: Store CEE DCBX DesiredCfg and RemoteCfg
This patch adds capability to query and store the CEE DCBX DesiredCfg
and RemoteCfg data from the LLDP MIB.
Added new member "desired_dcbx_config" in the i40e_hw data structure
to hold CEE only DesiredCfg data.
Change-ID: I19c550369594384eaff4cc63e690ca740231195d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Thu, 27 Aug 2015 15:42:36 +0000 (11:42 -0400)]
i40e: Add parsing for CEE DCBX TLVs
This patch adds parsing for CEE DCBX TLVs from the LLDP MIB.
While the driver gets the DCB CEE operational configuration from Firmware
using the "Get CEE DCBX Oper Config" AQ command there is a need to get
the CEE DesiredCfg Tx by firmware and DCB configuration Rx from peer; for
debug and other application purposes.
Change-ID: I9140edf1a25a2852c7eff805d81e5eff6266178d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 27 Aug 2015 15:42:35 +0000 (11:42 -0400)]
i40e: add more verbose error messages
Under certain circumstances, the device may not have enough resources to
enable all of the VFs that it advertises in config space. Although the
number of supported VFs is reported upon driver init, it is not obvious
when this is different from the number reported in config space. To
eliminate this confusion, add an error message explaining the problem.
Additionally, move the 'Allocating VFs' message down below the error
checks so as to prevent further confusion.
Change-ID: I45b7efca53a7aebf7777be33a8bc9d615ae48ea1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg [Thu, 27 Aug 2015 15:42:34 +0000 (11:42 -0400)]
i40e: inline interrupt enable
The interrupt enable function can be inlined by moving it to the header
file, which decreases the function call overhead for a frequently called
function.
Change-ID: I3214cc99593725768642680e7b8ce7e9bba7e44d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg [Thu, 27 Aug 2015 15:42:33 +0000 (11:42 -0400)]
i40e: fix erroneous WARN_ON
The driver was issuing a WARN_ON during ring size changes
because the code was cloning the rx_ring struct but
not zeroing out the pointers before allocating new memory.
Zero out the pointers in the cloned copy before allocating
new memory for them. In this case the code was correctly
avoiding memory leaks but still triggering the warning.
Change-ID: I186dd493948e9b7254ab0593d4aad8b68808918d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Thu, 8 Oct 2015 12:26:44 +0000 (05:26 -0700)]
Merge branch 'bpf_random32'
Daniel Borkmann says:
====================
BPF/random32 updates
BPF update to split the prandom state apart, and to move the
*once helpers to the core. For details, please see individual
patches. Given the changes and since it's in the tree for
quite some time, net-next is a better choice in our opinion.
v1 -> v2:
- Make DO_ONCE() type-safe, remove the kvec helper. Credits
go to Alexei Starovoitov for the __VA_ARGS__ hint, thanks!
- Add a comment to the DO_ONCE() helper as suggested by Alexei.
- Rework prandom_init_once() helper to the new API.
- Keep Alexei's Acked-by on the last patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 7 Oct 2015 23:20:39 +0000 (01:20 +0200)]
bpf: split state from prandom_u32() and consolidate {c, e}BPF prngs
While recently arguing on a seccomp discussion that raw prandom_u32()
access shouldn't be exposed to unpriviledged user space, I forgot the
fact that SKF_AD_RANDOM extension actually already does it for some time
in cBPF via commit
4cd3675ebf74 ("filter: added BPF random opcode").
Since prandom_u32() is being used in a lot of critical networking code,
lets be more conservative and split their states. Furthermore, consolidate
eBPF and cBPF prandom handlers to use the new internal PRNG. For eBPF,
bpf_get_prandom_u32() was only accessible for priviledged users, but
should that change one day, we also don't want to leak raw sequences
through things like eBPF maps.
One thought was also to have own per bpf_prog states, but due to ABI
reasons this is not easily possible, i.e. the program code currently
cannot access bpf_prog itself, and copying the rnd_state to/from the
stack scratch space whenever a program uses the prng seems not really
worth the trouble and seems too hacky. If needed, taus113 could in such
cases be implemented within eBPF using a map entry to keep the state
space, or get_random_bytes() could become a second helper in cases where
performance would not be critical.
Both sides can trigger a one-time late init via prandom_init_once() on
the shared state. Performance-wise, there should even be a tiny gain
as bpf_user_rnd_u32() saves one function call. The PRNG needs to live
inside the BPF core since kernels could have a NET-less config as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Chema Gonzalez <chema@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 7 Oct 2015 23:20:38 +0000 (01:20 +0200)]
random32: add prandom_init_once helper for own rngs
Add a prandom_init_once() facility that works on the rnd_state, so that
users that are keeping their own state independent from prandom_u32() can
initialize their taus113 per cpu states.
The motivation here is similar to net_get_random_once(): initialize the
state as late as possible in the hope that enough entropy has been
collected for the seeding. prandom_init_once() makes use of the recently
introduced prandom_seed_full_state() helper and is generic enough so that
it could also be used on fast-paths due to the DO_ONCE().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 7 Oct 2015 23:20:37 +0000 (01:20 +0200)]
random32: add prandom_seed_full_state helper
Factor out the full reseed handling code that populates the state
through get_random_bytes() and runs prandom_warmup(). The resulting
prandom_seed_full_state() will be used later on in more than the
current __prandom_reseed() user. Fix also two minor whitespace
issues along the way.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Frederic Sowa [Wed, 7 Oct 2015 23:20:36 +0000 (01:20 +0200)]
once: make helper generic for calling functions once
Make the get_random_once() helper generic enough, so that functions
in general would only be called once, where one user of this is then
net_get_random_once().
The only implementation specific call is to get_random_bytes(), all
the rest of this *_once() facility would be duplicated among different
subsystems otherwise. The new DO_ONCE() helper will be used by prandom()
later on, but might also be useful for other scenarios/subsystems as
well where a one-time initialization in often-called, possibly fast
path code could occur.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Frederic Sowa [Wed, 7 Oct 2015 23:20:35 +0000 (01:20 +0200)]
net: move net_get_random_once to lib
There's no good reason why users outside of networking should not
be using this facility, f.e. for initializing their seeds.
Therefore, make it accessible from there as get_random_once().
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 7 Oct 2015 15:40:13 +0000 (08:40 -0700)]
net: Do not drop to make_route if oif is l3mdev
Commit
deaa0a6a930 ("net: Lookup actual route when oif is VRF device")
exposed a bug in __ip_route_output_key_hash for VRF devices: on FIB lookup
failure if the oif is specified the current logic drops to make_route on
the assumption that the route tables are wrong. For VRF/L3 master devices
this leads to wrong dst entries and route lookups. For example:
$ ip route ls table vrf-red
unreachable default
broadcast 10.2.1.0 dev eth1 proto kernel scope link src 10.2.1.2
10.2.1.0/24 dev eth1 proto kernel scope link src 10.2.1.2
local 10.2.1.2 dev eth1 proto kernel scope host src 10.2.1.2
broadcast 10.2.1.255 dev eth1 proto kernel scope link src 10.2.1.2
$ ip route get oif vrf-red 1.1.1.1
1.1.1.1 dev vrf-red src 10.0.0.2
cache
With this patch:
$ ip route get oif vrf-red 1.1.1.1
RTNETLINK answers: No route to host
which is the correct response based on the default route
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 7 Oct 2015 08:16:09 +0000 (10:16 +0200)]
bpf, skb_do_redirect: clear sender_cpu before xmit
Similar to commit
c29390c6dfee ("xps: must clear sender_cpu before
forwarding"), we also need to clear the skb->sender_cpu when moving
from RX to TX via skb_do_redirect() due to the shared location of
napi_id (used on RX) and sender_cpu (used on TX).
Fixes:
27b29f63058d ("bpf: add bpf_redirect() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 6 Oct 2015 21:53:57 +0000 (23:53 +0200)]
net: hns: fix 32-bit build warning
The recently added hns driver causes a build warning in ARM
allmodconfig builds:
drivers/net/ethernet/hisilicon/hns/hnae.c: In function 'handles_show':
drivers/net/ethernet/hisilicon/hns/hnae.c:452:13: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
j, (u64)h->qs[i]->io_base);
^
This removes the pointless cast and prints the pointer address using
the "%p" format string in all three locations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Ringle [Tue, 6 Oct 2015 20:37:46 +0000 (16:37 -0400)]
net: Microchip encx24j600 driver
This ethernet driver supports the Micorchip enc424j600/626j600 Ethernet
controller over a SPI bus interface. This driver makes use of the regmap API to
optimize access to registers by caching registers where possible.
Datasheet:
http://ww1.microchip.com/downloads/en/DeviceDoc/39935b.pdf
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Oct 2015 11:46:03 +0000 (04:46 -0700)]
Merge branch 'broadcom-iproc'
Arun Parameswaran says:
====================
Add support for Broadcom's iProc MDIO and Cygnus Ethernet PHY
This patchset adds support for the iProc MDIO interface and the
Broadcom Cygnus SoC's internal Ethernet PHY.
The internal Ethernet PHY(s) in the Cygnus SoC's are accessed
via the MDIO interface found in most of the iProc based chips.
The patch also consolidates the common API's used by the
Broadcom phys to a common library. Existing Broadcom phy
drivers have been modified to use the common library API's.
This patch series is based on Linux v4.3-rc1 and is avaliable in:
https://github.com/Broadcom/cygnus-linux/tree/cygnus-net-phy-mdio-v3
The Ethernet driver for the iProc family will be submitted soon,
as will the device tree configurations for the different iProc
family SoCs.
Changes from v2:
- Modified drivers/net/phy/Kconfig to modify the BCM_CYGNUS_PHY
driver to 'depends on MDIO_BCM_IPROC' instead of 'select'.
- Added github branch to the cover letter
Changes from v1:
- Updated device tree documentation for the iProc MDIO driver
based on Florian's feedback.
- Moved the core register defines from the Cygnus PHY driver to
'include/linux/brcmphy.h' based on Florian's feedback.
- Created a new patch/commit to modify the bcm7xxx phy driver
to use the new core register defines.
- Modified the Kconfig entry for the Broadcom PHY library to
'tristate' instead of 'bool'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Parameswaran [Tue, 6 Oct 2015 19:25:50 +0000 (12:25 -0700)]
net: phy: bcm7xxx: Modified to use global core register defines
Modified the bcm7xxx phy driver to remove local core register
defines and use the common ones from "include/linux/brcmphy.h"
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Parameswaran [Tue, 6 Oct 2015 19:25:49 +0000 (12:25 -0700)]
net: phy: Broadcom Cygnus internal Etherent PHY driver
Add support for the Broadcom Cygnus SoCs internal PHY's.
The PHYs are 1000M/100M/10M capable with support for 'EEE'
and 'APD' (Auto Power Down).
This driver supports the following Broadcom Cygnus SoCs:
- BCM583XX (BCM58300, BCM58302, BCM58303, BCM58305)
- BCM113XX (BCM11300, BCM11320, BCM11350, BCM11360)
The PHY's on these SoC's require some workarounds for
stable operation, both during configuration time and
during suspend/resume. This driver handles the
application of the workarounds.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Parameswaran [Tue, 6 Oct 2015 19:25:48 +0000 (12:25 -0700)]
net: phy: Add Broadcom phy library for common interfaces
This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.
Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Parameswaran [Tue, 6 Oct 2015 19:25:47 +0000 (12:25 -0700)]
net: phy: Broadcom iProc MDIO bus driver
This patch adds support for the Broadcom iProc MDIO bus interface.
The MDIO interface can be found in the Broadcom iProc family Soc's.
The MDIO bus is accessed using a combination of command and data
registers. This MDIO driver provides access to the Etherent GPHY's
connected to the MDIO bus.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Parameswaran [Tue, 6 Oct 2015 19:25:46 +0000 (12:25 -0700)]
dt-bindings: net: Broadcom iProc MDIO bus driver device tree binding
Add device tree binding documentation for the Broadcom iProc MDIO
bus driver.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Oct 2015 11:38:37 +0000 (04:38 -0700)]
Merge branch 'net/rds/4.3-v3' of git://git./linux/kernel/git/ssantosh/linux
Santosh Shilimkar says:
====================
RDS: connection scalability and performance improvements
[v4]
Re-sending the same patches from v3 again since my repost of
patch 05/14 from v3 was whitespace damaged.
[v3]
Updated patch "[PATCH v2 05/14] RDS: defer the over_batch work to
send worker" as per David Miller's comment [4] to avoid the magic
value usage. Patch now makes use of already available but unused
send_batch_count module parameter. Rest of the patches are same as
earlier version v2 [3]
[v2]:
Dropped "[PATCH 05/15] RDS: increase size of hash-table to 8K" from
earlier version [1]. I plan to address the hash table scalability using
re-sizable hash tables as suggested by David Laight and David Miller [2]
This series addresses RDS connection bottlenecks on massive workloads and
improve the RDMA performance almost by 3X. RDS TCP also gets a small gain
of about 12%.
RDS is being used in massive systems with high scalability where several
hundred thousand end points and tens of thousands of local processes
are operating in tens of thousand sockets. Being RC(reliable connection),
socket bind and release happens very often and any inefficiencies in
bind hash look ups hurts the overall system performance. RDS bin hash-table
uses global spin-lock which is the biggest bottleneck. To make matter worst,
it uses rcu inside global lock for hash buckets.
This is being addressed by simply using per bucket rw lock which makes the
locking simple and very efficient. The hash table size is still an issue and
I plan to address it by using re-sizable hash tables as suggested on the list.
For RDS RDMA improvement, the completion handling is revamped so that we
can do batch completions. Both send and receive completion handlers are
split logically to achieve the same. RDS 8K messages being one of the
key usecase, mr pool is adapted to have the 8K mrs along with default 1M
mrs. And while doing this, few fixes and couple of bottlenecks seen with
rds_sendmsg() are addressed.
Series applies against 4.3-rc1 as well net-next. Its tested on Oracle
hardware with IB fabric for both bcopy as well as RDMA mode. RDS TCP is
tested with iXGB NIC. Like last time, iWARP transport is untested with
these changes. The patchset is also available at below git repo:
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux.git net/rds/4.3-v3
As a side note, the IB HCA driver I used for testing misses at least 3
important patches in upstream to see the full blown IB performance and
am hoping to get that in mainline with help of them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Oct 2015 11:27:13 +0000 (04:27 -0700)]
Merge branch 'pass_net_through_output_path'
Eric W. Biederman says:
====================
net: Pass net through the output path v2
This is the next installment of my work to pass struct net through the
output path so the code does not need to guess how to figure out which
network namespace it is in, and ultimately routes can have output
devices in another network namespace.
The first patch in this series is a fix for a bug that came in when sk
was passed through the functions in the output path, and as such is
probably a candidate for net. At the same time my later patches depend
on it so sending the fix separately would be confusing.
The second patch in this series is another fix that for an issue that
came in when sk was passed through the output path. I don't think it
needs a backport as I don't think anyone uses the path where the code
was incorrect.
The rest of the patchset focuses on the path from xxx_local_out to
dst_output and in the end succeeds in passing sock_net(sk) from the
socket a packet locally originates on to the dst->output function.
Given the size reduction in the code I think this counts as a cleanup as
much as feature work.
There remain a number of helper functions (like ip option processing) to
take care of before the network stack can support destination devices in
other network namespaces but with this set of changes the backbone of
the work is done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:47 +0000 (16:48 -0500)]
dst: Pass net into dst->output
The network namespace is already passed into dst_output pass it into
dst->output lwt->output and friends.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:46 +0000 (16:48 -0500)]
ipv4, ipv6: Pass net into ip_local_out and ip6_local_out
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:45 +0000 (16:48 -0500)]
ipv4, ipv6: Pass net into __ip_local_out and __ip6_local_out
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:44 +0000 (16:48 -0500)]
ipvlan: Cache net in ipvlan_process_v4_outbound and ipvlan_process_v6_outbound
Compute net once in ipvlan_process_v4_outbound and
ipvlan_process_v6_outbound and store it in a variable so that net does
not need to be recomputed next time it is used.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:43 +0000 (16:48 -0500)]
ppp: Cache net in pptp_xmit
Compute net and store it in a variable in pptp_xmit, so that the value
can be reused the next time it is needed.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:42 +0000 (16:48 -0500)]
ipv4: Cache net in ip_build_and_send_pkt and ip_queue_xmit
Compute net and store it in a variable in the functions
ip_build_and_send_pkt and ip_queue_xmit so that it does not need to be
recomputed next time it is needed.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:41 +0000 (16:48 -0500)]
ipv4: Cache net in iptunnel_xmit
Store net in a variable in ip_tunnel_xmit so it does not need
to be recomputed when it is used again.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:40 +0000 (16:48 -0500)]
ipv6: Merge ip6_local_out and ip6_local_out_sk
Stop hidding the sk parameter with an inline helper function and make
all of the callers pass it, so that it is clear what the function is
doing.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:39 +0000 (16:48 -0500)]
ipv6: Merge __ip6_local_out and __ip6_local_out_sk
Only __ip6_local_out_sk has callers so rename __ip6_local_out_sk
__ip6_local_out and remove the previous __ip6_local_out.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:38 +0000 (16:48 -0500)]
ipv4: Merge ip_local_out and ip_local_out_sk
It is confusing and silly hiding a parameter so modify all of
the callers to pass in the appropriate socket or skb->sk if
no socket is known.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:37 +0000 (16:48 -0500)]
ipv4: Merge __ip_local_out and __ip_local_out_sk
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:36 +0000 (16:48 -0500)]
dst: Pass a sk into .local_out
For consistency with the other similar methods in the kernel pass a
struct sock into the dst_ops .local_out method.
Simplifying the socket passing case is needed a prequel to passing a
struct net reference into .local_out.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:35 +0000 (16:48 -0500)]
net: Pass net into dst_output and remove dst_output_okfn
Replace dst_output_okfn with dst_output
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:34 +0000 (16:48 -0500)]
xfrm: Only compute net once in xfrm_policy_queue_process
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:33 +0000 (16:48 -0500)]
ipv4: Fix ip_queue_xmit to pass sk into ip_local_out_sk
After a packet has been encapsulated by a tunnel we should use the
tunnel sockets local multicast loopback flag to control if the
encapsulated packet should be locally loopback back.
Pass sk into ip_local_out_sk so that in the rare case we are dealing
with a tunneled packet whose tunnel destination address is a multicast
address the kernel properly decides to loopback this packet.
In practice I don't think this matters as ip_queue_xmit is used by
tcp, l2tp and sctp none of which I am aware of uses ip level
multicasting as they are all point to point communications protocols.
Let's fix this before someone uses ip_queue_xmit for a tunnel protocol
that does use multicast.
Fixes:
aad88724c9d5 ("ipv4: add a sock pointer to dst->output() path.")
Fixes:
b0270e91014d ("ipv4: add a sock pointer to ip_queue_xmit()")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Wed, 7 Oct 2015 21:48:32 +0000 (16:48 -0500)]
ipv4: Fix ip_local_out_sk by passing the sk into __ip_local_out_sk
In the rare case where sk != skb->sk ip_local_out_sk arranges
to call dst->output differently if the skb is queued or not.
This is a bug.
Fix this bug by passing the sk parameter of ip_local_out_sk through
from ip_local_out_sk to __ip_local_out_sk (skipping __ip_local_out).
Fixes:
7026b1ddb6b8 ("netfilter: Pass socket pointer down through okfn().")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Oct 2015 11:21:09 +0000 (04:21 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-07
This series contains updates to i40e and i40evf only.
Paul updates i40e to simply increase the amount of time we wait for a
reset to complete since we have seen in some rare occasions the reset
can take longer to complete.
Shannon updates the driver to turn on Wake-on-LAN by default if it is
enabled in the hardware config to begin with, rather than always disable
it and wait for the user to expressly turn it on. Added new device id's
and support for future devices. Fixed a possible type compare problem
between a size and possible negative number. Also fixed a shift value
that was wrong, which ended up with a bad bitmask. Did general house
cleaning of the driver to cleanup several low lying fruit in the
driver. Fixed an issue where new unicast address's would be added to
the VSI list and then immediately removed and would never actually
make it down to the hardware. Resolved the issue by removing the
separation from unicast and multicast in the search for filters to be
deleted.
Mitch fixes an issue where the hardware would continue to access the
memory formerly used by the rings for a VF which have been removed,
causing memory corruption or DMAR errors. To relieve this condition,
explicitly stop all rings associated with each VF before releasing its
resources. Also fixed a panic if the driver is unable to enable MSI-X
or its unable to acquire enough vectors, so propagate interrupt
allocation failure information to the calling function. Cleaned up
opcode that is not required.
Carolyn extends the size of the test available for the interrupt names
so that all the descriptive data available for the Flow Director
interrupts is not truncated.
Catherine fixes an issue where there was a possibility of speed getting
set to 0 if advertised is set to 0 (which is the case when autoneg is
disabled).
Jesse fixes the checksum on big endian machines, so added code to swap
it correctly. Also fixed a bug in the return from get_link_status()
where only true or false was being returned, but false could mean
multiple things. So allow the caller to get all the return values
in the call chain bubbled back to the source so that the reason for
the failure does not get lost.
Anjali adds statistics to keep track of how many times we ask the stack
to linearize the SKB because the hardware cannot handle SKBs with more
than 8 frags per segment/single packet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Oct 2015 11:01:28 +0000 (04:01 -0700)]
Merge tag 'regmap-offload-update-bits' of git://git./linux/kernel/git/broonie/regmap
regmap: Allow buses to provide a custom update_bits() operation
Some buses provide a native _update_bits() operation which for uncached
registers is faster than doing a read/modify/write cycle as it is a
single bus transaction. Add support for implementing this to regmap.
Mitch Williams [Thu, 27 Aug 2015 15:42:32 +0000 (11:42 -0400)]
i40e/i40evf: remove unused opcode
This opcode is not required. VFs that program RSS through the firmware
do it by interacting directly with the firmware, and do not need to use
the virtual channel for this functionality.
Change-ID: Iaf17d2600e28ff1b6be8653f2fe9df1facd23b0e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Thu, 27 Aug 2015 15:42:31 +0000 (11:42 -0400)]
i40evf: propagate interrupt allocation failure
Lower level functions are properly reporting errors, and higher-level
functions are correctly responding to errors, but the errors aren't
actually getting through. Typically, the middle-manager function seems
to want to shield its boss from any bad news.
This change fixes a panic if the driver is unable to enable MSI-X or is
unable to acquire enough vectors.
Change-ID: Ifd5787ce92519a5d97e4b465902db930d97b71a1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Neerav Parikh [Thu, 27 Aug 2015 15:42:30 +0000 (11:42 -0400)]
i40e: Additional checks for CEE APP priority validity
The firmware has added additional status information to allow software
to determine if the APP priority for FCoE/iSCSI/FIP is valid or not in
CEE DCBX mode.
This patch adds to support those additional checks and will only add
applications to the software table that have oper and sync bits set
without any error.
Change-ID: I0a76c52427dadf97d4dba4538a3068d05e4eb56b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Anjali Singhai Jain [Thu, 27 Aug 2015 15:42:29 +0000 (11:42 -0400)]
i40e/i40evf: Add a stat to keep track of linearization count
Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.
Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:20 +0000 (15:14 -0400)]
i40e/i40evf: fix unicast mac address add
When using something like "ip maddr add ..." to add another unicast mac
address to the netdev, the mac address comes into the set_rx_mode handler
in the multicast list whether it is a unicast or multicast address.
This was confusing the code when it was trying to search for addresses
that needed to be deleted from the VSI, because it was looking for the
VSI unicast address in the netdev unicast list. The result was that a
new unicast address would get added to the VSI list and then immediately
removed, and would never actually make it down into the hardware.
This patch removes the separation from unicast and multicast in the search
for filters to be deleted. It also simplifies the logic a little with a
jump to the bottom of the loop when an address is found. Now it doesn't
matter which netdev list the address is hiding in, we'll check them all.
Change-ID: Ie3685a92427ae7d2212bf948919ce295bc7a874c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg [Wed, 26 Aug 2015 19:14:19 +0000 (15:14 -0400)]
i40e: fix bug in return from get_link_status and avoid spurious link messages
Previously, the driver could call this function and have only true/false
returned, but false could mean multiple things like failure to read
or link was down. This change allows the caller to get all return values
in the call chain bubbled back to the source, which keeps information about
failures from being lost.
Also, in some unlikely scenarios, the firmware can become slow to respond
to admin queue (AQ) queries for link state. Should the AQ time out,
the driver can detect the state and avoid a link change when there
may have been none.
Change-ID: Ib2ac38407b7880750fb891b392fa77457fe6c21c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg [Wed, 26 Aug 2015 19:14:18 +0000 (15:14 -0400)]
i40e: add little endian conversion for checksum
The checksum is not correct on big endian machines so add code to swap it
correctly.
Change-ID: Ic92b886d172a2cbe49f5d7eee1bc78e447023c7b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:17 +0000 (15:14 -0400)]
i40e/i40evf: give up the __func__
During early development, we added the function name to all of the error
strings to make debugging simpler. Now that we've released the driver,
our users should have more comprehensible error messages. So tear the
roof off and give up the __func__. Ow.
Change-ID: I7e1766252c7a032b9af6520da6aff536bdfd533c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Catherine Sullivan [Wed, 26 Aug 2015 19:14:16 +0000 (15:14 -0400)]
i40e: Never let speed get set to 0 in get_settings
In ethtool, there is a possibility of speed getting set to 0
if advertise is set to 0 (which it is when autoneg is disabled).
We never want this to happen as the firmware will actually attempt
to set the speed to 0 sending link down, so add an extra check
to make sure this doesn't happen.
Change-ID: I62e0eeee2cbf043d8e6f5c9c9f0b92794e877f01
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Wed, 26 Aug 2015 19:14:15 +0000 (15:14 -0400)]
i40e: Fix for truncated interrupt name
This patch extends the size of the text available for the interrupt names.
Without this patch, all the descriptive data available for the Flow
Director interrupts is truncated.
Change-ID: I2ac458f23ac3b4ea8f1edf73edc283b1d3704c7f
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:14 +0000 (15:14 -0400)]
i40e/i40evf: assure clean asq status report
There was a possibility where the asq_last_status could get through without
update and thus report a previous error. I don't think we've actually seen
this happen, but this patch will help make sure it doesn't.
Change-ID: I9e33927052a5ee6ea21f80b66d4c4b76c2760b17
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:13 +0000 (15:14 -0400)]
i40e: make i40e_init_pf_fcoe to void
i40e_init_pf_fcoe() didn't return anything except 0, it prints enough
error info already, and no driver logic depends on the return value,
so this can be void.
Change-ID: Ie6afad849857d87a7064c42c3cce14c74c2f29d8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:12 +0000 (15:14 -0400)]
i40e: fix bad CEE status shift value
Fix a shift value that was wrong, ending up with a bad bitmask. Also add
a blank line between two sets of #defines for better readability.
Change-ID: I3e41fa2a2ab904d3a4e6cbf13972ab0036a10601
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:11 +0000 (15:14 -0400)]
i40e/i40evf: fix a potential type compare issue
Rework an if expression to assure there is no type compare problem between
a size and a possible negative number.
Change-ID: I4921fcc96abfcf69490efce020a9e4007f251c99
Reported-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:10 +0000 (15:14 -0400)]
i40e/i40evf: add driver support for new device ids
Early addition of new a device id.
Change-ID: I61a8c8556fdf4f5714be4e4089689e374f30293c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Wed, 26 Aug 2015 19:14:09 +0000 (15:14 -0400)]
i40e: stop VF rings
Explicitly stop the rings belonging to each VF when disabling SR-IOV.
Even though the VFs were gone, and the associated VSIs were removed, the
rings were not stopped, and in some circumstances the hardware would
continue to access the memory formerly used by the rings, causing memory
corruption or DMAR errors, both of which would lead to general malaise
of the kernel.
To relieve this condition, explicitly stop all the rings associated with
each VF before releasing its resources.
Change-ID: I78c05d562c66e7b594b7e48d67860f49b3e5b6ec
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Wed, 26 Aug 2015 19:14:08 +0000 (15:14 -0400)]
i40e: enable WoL operation if config bit show WoL capable
The driver was disabling Wake-on-LAN by default and waiting for the user
to expressly turn it on. This patch has the driver turning on WoL from
the start if enabled in the hardware config, which matches the behavior
of our other drivers.
Change-ID: I43faedb907f8ba4d1a61b72a7c86072b97af12b1
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Paul M Stillwell Jr [Wed, 26 Aug 2015 19:14:07 +0000 (15:14 -0400)]
i40e: Increase the amount of time we wait for reset to be done
In some rare cases the reset can take longer to complete so increase the
amount of time we wait.
Change-ID: Ib5628ec54b526a811ee33d1214fe763226406671
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Tue, 6 Oct 2015 21:49:58 +0000 (14:49 -0700)]
tcp: ensure prior synack rtx behavior with small backlogs
Some applications use a listen() backlog of 1.
Prior kernels were silently enforcing a qlen_log of 4, so that we were
sending up to /proc/sys/net/ipv4/tcp_synack_retries SYNACK messages.
Fixes:
ef547f2ac16b ("tcp: remove max_qlen_log")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuvaraja Mariappan [Tue, 6 Oct 2015 17:53:29 +0000 (10:53 -0700)]
net: ipv4: tcp.c Fixed an assignment coding style issue
Fixed an assignment coding style issue
Signed-off-by: Yuvaraja Mariappan <ymariappan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:52:14 +0000 (04:52 -0700)]
Merge branch 's390-net'
Ursula Braun says:
====================
s390: qeth patches for net-next
here are some s390 related patches for net-next. The qeth patches
are performance optimizations in the driver. The qdio patch corrects
a warning condition.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Tue, 6 Oct 2015 13:12:29 +0000 (15:12 +0200)]
s390/qdio: fix WARN_ON_ONCE condition
If HiperSockets Completion Queueing is enabled, qdio always
issues a warning, since the condition is always met.
This patch fixes the condition in WARN_ON_ONCE that was always
true.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lakhvich Dmitriy [Tue, 6 Oct 2015 13:12:28 +0000 (15:12 +0200)]
s390/qeth: optimize MAC handling in rx_mode callback
In layer2 mode of the qeth driver, MAC address lists
from struct net_device require mapping to the OSA-card.
The existing implementation is inefficient for lists with
more than several MAC addresses, since for every
ndo_set_rx_mode callback it removes all MAC addresses first,
and then registers the current MAC address list.
This patch changes implementation of ndo_set_rx_mode callback
in qeth, only performing hardware registration/removal for
new/deleted addresses. To shorten lookup of MAC addresses
registered addresses are kept in a hashtable instead of a
linear list.
Signed-off-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reviewed-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Reviewed-by: Thomas Richter <tmricht@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Richter [Tue, 6 Oct 2015 13:12:27 +0000 (15:12 +0200)]
s390/qeth: switch to napi_gro_receive
Add support for GRO (generic receive offload) in the layer 2
part of device driver qeth. This results in a performance
improvement when GRO and RX is turned on.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:49:39 +0000 (04:49 -0700)]
Merge branch 'bridge-netlink-port-attrs'
Nikolay Aleksandrov says:
====================
bridge: netlink: complete port attribute support
This is the second set that completes the bridge port's netlink support and
makes everything from sysfs available via netlink. I've used sysfs as a
guide of what and how to set again. I've tested setting/getting every
option and also this time tested enabling KASAN. Again there're a few long
line warnings about the ifla attribute names in br_port_info_size() but
as the previous set - it's good to know what's been accounted for.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 6 Oct 2015 12:12:02 +0000 (14:12 +0200)]
bridge: netlink: add support for port's multicast_router attribute
Add IFLA_BRPORT_MULTICAST_ROUTER to allow setting/getting port's
multicast_router via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 6 Oct 2015 12:12:01 +0000 (14:12 +0200)]
bridge: netlink: allow to flush port's fdb
Add IFLA_BRPORT_FLUSH to allow flushing port's fdb similar to sysfs's
flush.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 6 Oct 2015 12:12:00 +0000 (14:12 +0200)]
bridge: netlink: export port's timer values
Add the following attributes in order to export port's timer values:
IFLA_BRPORT_MESSAGE_AGE_TIMER, IFLA_BRPORT_FORWARD_DELAY_TIMER and
IFLA_BRPORT_HOLD_TIMER.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 6 Oct 2015 12:11:59 +0000 (14:11 +0200)]
bridge: netlink: export port's topology_change_ack and config_pending
Add IFLA_BRPORT_TOPOLOGY_CHANGE_ACK and IFLA_BRPORT_CONFIG_PENDING to
allow getting port's topology_change_ack and config_pending respectively
via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 6 Oct 2015 12:11:58 +0000 (14:11 +0200)]
bridge: netlink: export port's id and number
Add IFLA_BRPORT_(ID|NO) to allow getting port's port_id and port_no
respectively via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 6 Oct 2015 12:11:57 +0000 (14:11 +0200)]
bridge: netlink: export port's designated cost and port
Add IFLA_BRPORT_DESIGNATED_(COST|PORT) to allow getting the port's
designated cost and port respectively via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 6 Oct 2015 12:11:56 +0000 (14:11 +0200)]
bridge: netlink: export port's bridge id
Add IFLA_BRPORT_BRIDGE_ID to allow getting the designated bridge id via
netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Tue, 6 Oct 2015 12:11:55 +0000 (14:11 +0200)]
bridge: netlink: export port's root id
Add IFLA_BRPORT_ROOT_ID to allow getting the designated root id via
netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 17:49:04 +0000 (10:49 -0700)]
net: Lookup actual route when oif is VRF device
If the user specifies a VRF device in a get route query the custom route
pointing to the VRF device is returned:
$ ip route ls table vrf-red
unreachable default
broadcast 10.2.1.0 dev eth1 proto kernel scope link src 10.2.1.2
10.2.1.0/24 dev eth1 proto kernel scope link src 10.2.1.2
local 10.2.1.2 dev eth1 proto kernel scope host src 10.2.1.2
broadcast 10.2.1.255 dev eth1 proto kernel scope link src 10.2.1.2
$ ip route get oif vrf-red 10.2.1.40
10.2.1.40 dev vrf-red
cache
Add the flags to skip the custom route and go directly to the FIB. With
this patch the actual route is returned:
$ ip route get oif vrf-red 10.2.1.40
10.2.1.40 dev eth1 src 10.2.1.2
cache
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:29:18 +0000 (04:29 -0700)]
Merge tag 'mac80211-next-for-davem-2015-10-05' of git://git./linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the current cycle, we have the following right now:
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from RafaĆ)
* support for netlink dump in vendor commands (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:27:51 +0000 (04:27 -0700)]
Merge branch 'l3mdev_saddr_op'
David Ahern says:
====================
net: Add saddr op to l3mdev and vrf
First 2 patches are re-sends of patches that got lost in the ethosphere
Tuesday; they were part of the first round of l3mdev conversions.
Next 3 handle the source address lookup for raw and datagram sockets
bound to a VRF device.
The conversion to the get_saddr op also fixes locally originated TCP
packets showing up at the VRF device. The use of the FLOWI_FLAG_L3MDEV_SRC
flag in ip_route_connect_init was causing locally generated packets
to skip the VRF device.
v2
- rebased to top of net-next per device delete fix and hash based
multipath patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 15:51:27 +0000 (08:51 -0700)]
net: Add l3mdev saddr lookup to raw_sendmsg
ping originated on box through a VRF device is showing up in tcpdump
without a source address:
$ tcpdump -n -i vrf-blue
08:58:33.311303 IP 0.0.0.0 > 10.2.2.254: ICMP echo request, id 2834, seq 1, length 64
08:58:33.311562 IP 10.2.2.254 > 10.2.2.2: ICMP echo reply, id 2834, seq 1, length 64
Add the call to l3mdev_get_saddr to raw_sendmsg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 15:51:26 +0000 (08:51 -0700)]
net: Add source address lookup op for VRF
Add operation to l3mdev to lookup source address for a given flow.
Add support for the operation to VRF driver and convert existing
IPv4 hooks to use the new lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 15:51:25 +0000 (08:51 -0700)]
net: Refactor path selection in __ip_route_output_key_hash
VRF device needs the same path selection following lookup to set source
address. Rather than duplicating code, move existing code into a
function that is exported to modules.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 15:51:24 +0000 (08:51 -0700)]
net: Add netif_is_l3_slave
IPv6 addrconf keys off of IFF_SLAVE so can not use it for L3 slave.
Add a new private flag and add netif_is_l3_slave function for checking
it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 15:51:23 +0000 (08:51 -0700)]
net: Rename FLOWI_FLAG_VRFSRC to FLOWI_FLAG_L3MDEV_SRC
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 5 Oct 2015 14:32:51 +0000 (08:32 -0600)]
net: Fix vti use case with oif in dst lookups for IPv6
It occurred to me yesterday that
741a11d9e4103 ("net: ipv6: Add
RT6_LOOKUP_F_IFACE flag if oif is set") means that xfrm6_dst_lookup
needs the FLOWI_FLAG_SKIP_NH_OIF flag set. This latest commit causes
the oif to be considered in lookups which is known to break vti. This
explains why
58189ca7b274 did not the IPv6 change at the time it was
submitted.
Fixes:
42a7b32b73d6 ("xfrm: Add oif to dst lookups")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 5 Oct 2015 14:19:59 +0000 (17:19 +0300)]
gianfar: Add WAKE_UCAST and "wake-on-filer" support
This enables eTSEC's filer (Rx parser) and the FGPI Rx
interrupt (Filer General Purpose Interrupt) as a wakeup
source event.
Upon entering suspend state, the eTSEC filer is given
a rule to match incoming L2 unicast packets. A packet
matching the rule will be enqueued in the Rx ring and
a FGPI Rx interrupt will be asserted by the filer to
wakeup the system. Other packet types will be dropped.
On resume the filer table is restored to the content
before entering suspend state.
The set of rules from gfar_filer_config_wol() could be
extended to implement other WoL capabilities as well.
The "fsl,wake-on-filer" DT binding enables this capability
on certain platforms that feature the necessary power
management infrastructure, targeting mainly printing and
imaging applications.
(refer to Power Management section of the SoC Ref Man)
Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 5 Oct 2015 14:19:58 +0000 (17:19 +0300)]
powerpc: dts: p1022si: Add fsl,wake-on-filer for eTSEC
Enable the "wake-on-filer" (aka. wake on user defined packet)
wake on lan capability for the eTSEC ethernet nodes.
Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 5 Oct 2015 14:19:57 +0000 (17:19 +0300)]
doc: dt: net: Add fsl,wake-on-filer for eTSEC
Add the "fsl,wake-on-filer" property for eTSEC nodes to
indicate that the system has the power management
infrastructure needed to be able to wake up the system
via FGPI (filer, aka. h/w rx parser) interrupt.
Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 11:18:04 +0000 (04:18 -0700)]
Merge branch 'ovs-ipv6-tunnel'
Jiri Benc says:
====================
openvswitch: add IPv6 tunneling support
This builds on the previous work that added IPv6 support to lwtunnels and
adds IPv6 tunneling support to ovs.
To use IPv6 tunneling, there needs to be a metadata based tunnel net_device
created and added to the ovs bridge. Currently, only vxlan is supported by
the kernel, with geneve to follow shortly. There's no need nor intent to add
a support for this into the vport-vxlan (etc.) compat layer.
v3: dropped the last two patches added in v2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Mon, 5 Oct 2015 11:09:47 +0000 (13:09 +0200)]
openvswitch: netlink attributes for IPv6 tunneling
Add netlink attributes for IPv6 tunnel addresses. This enables IPv6 support
for tunnels.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Mon, 5 Oct 2015 11:09:46 +0000 (13:09 +0200)]
openvswitch: add tunnel protocol to sw_flow_key
Store tunnel protocol (AF_INET or AF_INET6) in sw_flow_key. This field now
also acts as an indicator whether the flow contains tunnel data (this was
previously indicated by tun_key.u.ipv4.dst being set but with IPv6 addresses
in an union with IPv4 ones this won't work anymore).
The new field was added to a hole in sw_flow_key.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Mon, 5 Oct 2015 10:11:21 +0000 (12:11 +0200)]
bridge: netlink: make br_fill_info's frame size smaller
When KASAN is enabled the frame size grows > 2048 bytes and we get a
warning, so make it smaller.
net/bridge/br_netlink.c: In function 'br_fill_info':
>> net/bridge/br_netlink.c:1110:1: warning: the frame size of 2160 bytes
>> is larger than 2048 bytes [-Wframe-larger-than=]
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 3 Oct 2015 18:43:46 +0000 (11:43 -0700)]
net: Add support for filtering neigh dump by device index
Add support for filtering neighbor dumps by device by adding the
NDA_IFINDEX attribute to the dump request.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 7 Oct 2015 10:01:53 +0000 (03:01 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-03
This series contains updates to i40e and i40evf, some of which are to
resolve more Red Hat bugzilla issues.
Jiang Liu updates the i40e and i40evf drivers to use numa_mem_id()
instead of numa_node_id() to get the nearest node with memory which
better supports memoryless nodes.
Anjali fixes an issue from Dan Carpenter <dan.carpenter@oracle.com>,
to resolve a memory leak in X722 RSS configuration path, where we should
free the memory allocated before exiting.
Shannon modifies the drivers to ensure we have the spinlocks before we
clear the ARQ and ASQ management registers. In addition, we widen the
locked portion insert a sanity check to ensure we are working with safe
register values.
Mitch fixes an issue where under certain circumstances, we can get an
extra VF_RESOURCES message from the PF driver at runtime. When this
occurs, we need to parse it because our VSI may have changed and that
will affect the relationship with the PF driver. But this parsing also
blows away our current MAC address, so resolve the issue by restoring
the current MAC address from the netdev struct after we parse the
resource message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 3 Oct 2015 17:09:07 +0000 (18:09 +0100)]
net: dsa: better error reporting
Add additional error reporting to the generic DSA code, so it's easier
to debug when things go wrong. This was useful when initially bringing
up
88e6176 on a new board.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 3 Oct 2015 17:09:01 +0000 (18:09 +0100)]
net: dsa: mv88e6xxx: remove link polling
The link status is polled by the generic phy layer, there's no need to
duplicate that polling with additional polling. This additional polling
adds additional MDIO traffic, and races with the generic phy layer,
resulting in missing or duplicated link status messages.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Ringle [Thu, 1 Oct 2015 16:38:07 +0000 (12:38 -0400)]
regmap: Allow installing custom reg_update_bits function
This commit allows installing a custom reg_update_bits function for cases where
the hardware provides a mechanism to set or clear register bits without a
read/modify/write cycle. Such is the case with the Microchip ENCX24J600.
If a custom reg_update_bits function is provided, it will only be used against
volatile registers.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
David S. Miller [Tue, 6 Oct 2015 13:25:43 +0000 (06:25 -0700)]
Revert "regmap: Allow installing custom reg_update_bits function"
This reverts commit
7741c373cf3ea1f5383fa97fb7a640a429d3dd7c.