drm/amd/display: Fix black flash when switching from ODM2to1 to ODMBypass

[Why]
On secondary display hotplug we switch primary
stream from ODM2to1 to ODMBypass mode. Current
logic will trigger disabling front end for this
stream.

[How]
We need to check if prev_odm_pipe is equal to NULL
in order to disable dangling planes in this scenario.

Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix check for stream and plane

[WHY]
Function wasn't returning false when it had a no stream

[HOW]
Made it return false when it had no stream.

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ethan Wellenreiter <Ethan.Wellenreiter@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Re-initialize viewport after pipe merge

[Why]
Pipes get merged in preparation for SubVP but if they don't get used, and
are in ODM or some other multi pipe config, it would calculate the
voltage level with a viewport of just one pipe from when they were split
resulting in too low of a voltage level.

[How]
Made it so that the viewport and other timing settings get rebuilt and re-
initialized after the pipe merge, before calculating the voltage level so it
would calculate it correctly.

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ethan Wellenreiter <Ethan.Wellenreiter@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Use correct plane for CAB cursor size allocation

[Why&How]
plane and stream variables used for cursor size allocation calculation
were stale from previous iteration. Redo the iteration to find the
correct cursor plane for the calculation.

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: ensure no PCIe peer access for CPU XGMI iolinks

[Why] Devices with CPU XGMI iolink do not support PCIe peer access.

Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.201

Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: bump SMU 13.0.0 driver_if header version

To suppress the warning about version mismatch with
the latest 78.54.0 PMFW.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: use vbios carried pptable for all SMU13.0.7 SKUs

For those SMU13.0.7 unsecure SKUs, the vbios carried pptable is ready to go.
Use that one instead of hardcoded softpptable.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: use vbios carried pptable for those supported SKUs

For some SMU13.0.0 SKUs, the vbios carried pptable is ready to go.
Use that one instead of hardcoded softpptable.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add visual confirm color support for SubVP

[Why && How]
We would like to have visual confirm color support for SubVP.
1. Set visual confirm color to red: SubVP is enable on this
display;
2. Set visual confirm color to green: SubVP is enable on
other display and DRR is on this display;
3. Set visual confirm color to blue: SubVP is enable on
other display and DRR is off on this display;

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.132.0

- Fix comment to indicate correct visual confirm option

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add comments.

Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Revert "program k1/k2 divider for virtual signal for DCN32"

[Why & How]
This reverts commit e6cf22ef5fae493a99e162c3f2e7233448d2b970 since it
causes a SubVP related regression: "Switching between windowed video and
fullscreen can intermittently cause black screen"

Fixes: e6cf22ef5fae49 ("drm/amd/display: program k1/k2 divider for virtual signal for DCN32")
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix primary EDP link detection

[HOW&WHY]
EDP link detection must
be updated to support a primary EDP with a
link index of greater than 0.

* SWDEV-342936 - dc: DSC bringup for SAG 1.5

[WHY]
SmartAccess Graphics 1.5 (a.k.a SmartMux 1.5)
requires seamless switching between GPUs
with DSC enabled.

[HOW]
Moved DSC programming to
apply_single_control_ctx_to_hw before the stream
enablement logic to ensure the CRC checker provides valid
values for non-black frames
allowing the system to come out of forced PSR on
d2i.

Added additional logic to both generate a black
frame through setVisibility calls and keep track
of the CRCs values for this black frame when
coming out of forced PSR.

Updating logic for DalRegKey_DisableDSC to disable
DSC on EDP and all ports for systems.

[CLEANED]
dc: Moved DSC programming to before stream enablement

[HOW&WHY]
Moved DSC programming to
apply_single_control_ctx_to_hw before the stream
enablement logic.

Co-authored-by: sregolui <sregolui@amd.com>
Reviewed-by: Jayendran Ramani <Jayendran.Ramani@amd.com>
Reviewed-by: Harry Vanzylldejong <Harry.Vanzylldejong@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: sregolui <sregolui@amd.com>
Signed-off-by: Iswara Nagulendran <Iswara.Nagulendran@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix wrong register access

[why]
fw version check was for release branch.
for staging, it has a chance to enter wrong code path.

Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: use actual cursor size instead of max for CAB allocation

[Why&How]
When calculating allocation for cursor size, get the real cursor through
the HUBP instead of using the maximum cursor size for more optimal
allocation

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: disable display fresh from MALL on an edge case for DCN321

[Why&How]
When using a 4k monitor when cursor caching is not supported due to
framebuffer being on an uncacheable address, enabling display refresh
from MALL would trigger corruption if SS is enabled.

Prevent entering SS if we are on the edge case and cursor caching is not
possible. Do this only if cursor size larger than a 64x64@4bpp. Pull the
cursor size calculation out of if condition since cursor address may not
be set on all platforms

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix CAB cursor size allocation for DCN32/321

For calculating cursor size allocation, surface size was used, resulting
in over allocation

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Missing HPO instance added

[Why & How]
Number of encoder is set to 4 but only 3 instances are created.

Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo Chen <sancchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refactor edp dsc codes.

Refactor edp dsc codes.

We split out edp dsc config from "global" to "per-panel" config settings.

Reviewed-by: Mike Hsieh <mike.hsieh@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: SubVP missing scaling case

[Description]
For SubVP scaling case we have to combine
the plane scaling and stream scaling.

Use UCLK dummy p-state WM for FCLK WM set C

[Description]
For DCN32/321 program dummy UCLK P-state watermark into FCLK
watermark set C register.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add support for visual confirm color

[Why]
We want to get the visual confirm color of the bottom-most pipe
for test automation.

[How]
Save the visual confirm color to plane_state before program to MPC;

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Allow PHY state update between same states

[Why & How]
In some cases, there are calls to transition from TX_ON to TX_ON, such as
when using MST or during resolution change. This is expected, so allow HW
programming to continue.

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Cleanup PSR flag

[Why]
enable_sw_cntl_psr flag is not needed.
For PSR1 and PSR2, we should be passing
dirty rectangle and cursor updates to FW
regardless of enable_sw_cntl_psr flag.

[How]
Remove enable_sw_cntl_psr flag from driver.
Send cursor info and dirty rectagle status to
dmub only in the case of dcn31 and above.

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Cursor lag with PSR1 eDP

[Why]
On edp with psr1, we do not provide updates
of the cursor position regularly to firmware
like with PSR2. To send updates regularly,
the flag enable_sw_cntl_psr has to equal 1,
but cursor update should be provided
regularly to FW regardless of that flag.

[How]
Ensure that we always send cursor updates to
firmware when PSR version equals 1.

Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DC debug option to force LTTPR mode

[WHY]
Useful for external teams debugging LTTPR issues

Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add a override flag as wa for some specific dongle

[Why & How]
Add a override flag as wa for some specific dongle

Co-authored-by: Leo Chen <sancchen@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo Chen <SanChuan.Chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Only commit SubVP state after pipe programming

[Description]
We only want to commit the SubVP config to DMCUB
after the main and phantom pipe programming has
completed. Commiting the state early can cause
issues such as P-State being allowed by the HW
early which causes the SubVP state machine to
go into a bad state

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove assert from PHY state update

[Why & How]
In some cases, there are calls to transition from TX_ON to TX_ON. This is
expected, so do not assert. However, these are redundant, so return
prematurely.

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: set dig fifo read start level to 7 before dig fifo reset

[Why]
DIG_FIFO_ERROR = 1 caused mst daisy chain 2nd monitor black.

[How]
We need to set dig fifo read start level = 7 before dig fifo reset during dig
fifo enable according to hardware designer's suggestion. If it is zero, it will
cause underflow or overflow and DIG_FIFO_ERROR = 1.

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Wang Fudong <Fudong.Wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Fix use-after-free in amdgpu_cs_ioctl

[Why]
In amdgpu_cs_ioctl, amdgpu_job_free could be performed ealier if there
is -ERESTARTSYS error. In this case, job->hw_fence could be not
initialized yet. Putting hw_fence during amdgpu_job_free could lead to a
use-after-free warning.

[How]
Check if drm_sched_job_init is performed before job_free by checking
s_fence.

v2: Check hw_fence.ops instead since it could be NULL if fence is not
initialized. Reverse the condition since !=NULL check is discouraged in
kernel.

Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix OTG H timing reset for dcn314

[Why]
When ODM is enabled, H timing control register reset
to 0. Div mode manual field get overwritten causing
no display on certain modes for dcn314.

[How]
Use REG_UPDATE instead of REG_SET to set div_mode
field.

Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refine aux transaction before retrieve caps

[Why]
LTTPR caps will read fail if aux channel is not active.

[How]
1.Perform 600 read upto 10 retry with 1ms delay in between.
2.If fail, return false and trigger another retry detection.
3.If pass, read LTTPR caps in retrieve link caps.

Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix DCN32 DPSTREAMCLK_CNTL programming

[Why]
Each index in the DPSTREAMCLK_CNTL register
phyiscally maps 1-to-1 with HPO stream encoder
instance. On the other hand, each index in
DTBCLK_P_CNTL physically maps 1-to-1 with OTG
instance.

Current DCN32 DPSTREAMCLK_CLK programing assumes
that OTG instance always maps 1-to-1 with
HPO stream encoder instance. This is not always
guaranteed and can result in blackscreen.

[How]
Program the correct dpstreamclk instance with
the correct dtbclk_p source.

Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Don't choose SubVP display if ActiveMargin > 0

[Description]
There can be SubVP scheduling issues if a SubVP
display is chosen has ActiveDramClockChangeLatency > 0.
Block this case for now, and enable Vactive case
(later) to handle this.

Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set ODM policy based on number of DSC slices

[Why & How]
Add addtional check in CalculateODMMode for cases where the ODM combine
is needed due to number of DSC slices.

Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.200

This version brings along following fixes:
- Modify pipe split policy
- Fix odm 2:1 policy in 4k144 mode
- Correct HDMI ODM combine policy
- Change AUX NACK behavior
- Change runtime initialization for DCN32/321
- Fix cursor flicker in PSRSU
- Fix k1/k2 divider for virtual signal for DCN32
- Free phantom plane after removing the context
- Add interface to track PHY state
- Add SubVP scaling case
- Add log clock table for SMU
- Fix atomic_check check
- Fix SMU 13.0.0 driver_if header
- Fix doorbells allocation

Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add missing pci_disable_device() in amdgpu_pmops_runtime_resume()

Add missing pci_disable_device() if amdgpu_device_resume() fails.

Fixes: 8e4d5d43cc6c ("drm/amdgpu: Handling of amdgpu_device_resume return value for graceful teardown")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix variable dereferenced before check

Fixes the following smatch warning:

drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:311 dc_dmub_srv_p_state_delegate()
warn: variable dereferenced before check 'dc' (see line 309)

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: sunliming <sunliming@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Remove the unneeded result variable

Return the value sdma_v5_2_start() directly instead of storing it in
another redundant variable.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Update mes_v11_api_def.h

New GFX11 MES FW adds the trap_en bit. For now hardcode to 1 (traps
enabled).

Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: disable FRU access on special SIENNA CICHLID card

Below driver load error will be printed, not friendly to end user.

amdgpu: ATOM BIOS: 113-D603GLXE-077
[drm] FRU: Failed to get size field
[drm:amdgpu_fru_get_product_info [amdgpu]] *ERROR* Failed to read FRU Manufacturer, ret:-5

Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd: remove possible condition with no effect (if == else)

This patch fix cocci warning:
drivers/gpu/drm/amd/display/dc/dcn314/dcn314_resource.c:1816:6-8:
WARNING: possible condition with no effect (if == else).

Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd: remove possible condition with no effect (if == else)

This patch fix cocci warning:
drivers/gpu/drm/amd/display/dc/core/dc.c:3335:2-4: WARNING:
possible condition with no effect (if == else).

Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd: fix potential memory leak

This patch fix potential memory leak (clk_src) when function run
into last return NULL.

Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd: fix potential memory leak

This patch fix potential memory leak (clk_src) when function run
into last return NULL.

s/free/kfree/ - Alex

Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: mmVM_L2_CNTL3 register not initialized correctly

The mmVM_L2_CNTL3 register is not assigned an initial value

Signed-off-by: Qu Huang <jinsdb@126.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm: amd: amdgpu: ACPI: Add comment about ACPI_FADT_LOW_POWER_S0

According to the ACPI specification [1], the ACPI_FADT_LOW_POWER_S0
flag merely means that it is better to use low-power S0 idle on the
given platform than S3 (provided that the latter is supported) and it
doesn't preclude using either of them (which of them will be used
depends on the choices made by user space).

However, on some systems that flag is used to indicate whether or not
to enable special firmware mechanics allowing the system to save more
energy when suspended to idle.  If that flag is unset, doing so is
generally risky.

Accordingly, add a comment to explain the ACPI_FADT_LOW_POWER_S0 check
in amdgpu_acpi_is_s0ix_active(), the purpose of which is otherwise
somewhat unclear.

Link: https://uefi.org/specs/ACPI/6.4/05_ACPI_Software_Programming_Model/ACPI_Software_Programming_Model.html#fixed-acpi-description-table-fadt
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: use time_after(a,b) to replace "a>b"

time_after() deals with timer wrapping correctly.

Signed-off-by: Yu Zhe <yuzhe@nfschina.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use dev_info to benefit mGPU case

'free PSP TMR buffer' happens in suspend, but sometimes
in mGPU config, it mixes with PSP resume log printing from
another GPU, which is confusing. So use dev_info instead of
DRM_INFO for printing.

[drm] PSP is resuming...
[drm] reserve 0xa00000 from 0x877e000000 for PSP TMR
amdgpu 0000:e3:00.0: amdgpu: GECC is enabled
amdgpu 0000:e3:00.0: amdgpu: SECUREDISPLAY: securedisplay ta ucode is not available
amdgpu 0000:e3:00.0: amdgpu: SMU is resuming...
amdgpu 0000:e3:00.0: amdgpu: smu driver if version = 0x00000040, smu fw if version = 0x00000041, smu fw program = 0, version = 0x003a5400 (58.84.0)
amdgpu 0000:e3:00.0: amdgpu: SMU driver if version not matched
amdgpu 0000:e3:00.0: amdgpu: dpm has been enabled
amdgpu 0000:e3:00.0: amdgpu: SMU is resumed successfully!
[drm] DMUB hardware initialized: version=0x02020014
[drm] free PSP TMR buffer
[drm] kiq ring mec 2 pipe 1 q 0

Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use adev_to_drm to get drm device

adev_to_drm is used everywhere in amdgpu code, so modify
it to keep consistency.

Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add MGCG perfmon setting for gfx11

Enable GFX11 MGCG perfmon setting.
V2: set rlc to saft mode before setting.

Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: avoid soft reset check when gpu recovery disabled

Avoid soft reset, even ip hang check (ring/ib test) when gpu recovery
disabled.

v2: add missing "}"

Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Fix isa version for the GC 10.3.7

Correct the isa version for handling KFD test.

Fixes: 7c4f4f197e0c ("drm/amdkfd: Add GC 10.3.6 and 10.3.7 KFD definitions")
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Fix page table setup on Arcturus

When translate_further is enabled, page table depth needs to
be updated. This was missing on Arcturus MMHUB init. This was
causing address translations to fail for SDMA user-mode queues.

Fixes: 352e683b72e7 ("drm/amdgpu: Enable translate_further to extend UTCL2 reach")
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: Allocate doorbells only when needed

Only allocate doorbells when the first queue is created on a GPU or the
doorbells need to be mapped into CPU or GPU virtual address space. This
avoids allocating doorbells unnecessarily and can allow more processes
to use KFD on multi-GPU systems.

Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Kent Russell <kent.Russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: update SMU 13.0.0 driver_if header

To fit the latest 78.53 PMFW.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove redundant check in atomic_check

[Why]
We have 2 back-to-back checks for skipping connectors.
Logically one of them will do the job.

[How]
Remove redundant check.

Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Adding log clock table from SMU

[Why & How]
Adding log for clock table from SMU helps with the debugging process.
Implemented using DC_LOG_SMU to output log.

Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo Chen <sancchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Uncomment SubVP scaling case

[Description]
Uncomment scaling cmd assignment since
FW headers are now promoted.

Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add interface to track PHY state

[Why]
Sometimes pixel clock needs to remain active after transmitter disable.

[How]
Use update_phy_state to track PHY state after stream
enable/disable and program pixel clock as needed.

Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Free phantom plane and stream properly

[Description]
Refcount is incremented on allocation and
when adding to the context. Therefore we must
release the phantom plane and stream after
removing from the context.

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: program k1/k2 divider for virtual signal for DCN32

[Why&How]
When using IGT, kms_bw multi display tests trigger an assert since
we ignore virtual signal type. k1/k2 dividers should be correctly
programmed if VSYNC needs to be correct. Add the appropriate condition
to the if arm to fix this.

Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Cursor flicker when entering PSRSU

[Why]
The DAL driver may transmit the wrong cursor position to PSRSU
DMUB driver when there are multiple planes.

[How]
Currently the driver apply the HW cursor on the top plane. So we
should only transmit the cursor position on the top plane to
PSRSU DMUB driver.

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: change to runtime initialization for reg offsets for DCN321

DC was using compile time initialization of register addresses using
SR_* macros and their variants. These have been converted to use runtime
initialization.

The REG_STRUCT macro is a definition that is added to SR_* macros.
During initialization, this must be defined before SR_* macros are
invoked, which are in turn invoked through various IP initialization macros.

Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: change to runtime initialization for reg offsets for DCN32

DC was using compile time initialization of register addresses using
SR_* macros and their variants. These have been converted to use runtime
initialization.

The REG_STRUCT macro is a definition that is added to SR_* macros.
During initialization, this must be defined before SR_* macros are
invoked, which are in turn invoked through various IP initialization macros.

Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Change AUX NACK behavior

[Why]
Retrying on receiving a NACK can result in long overall EDID read times
in some cases.

[How]
Retry only on DEFER and return immediately on NACK.

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: HDMI ODM Combine Policy Correction

[WHY]
Reprogramming the stream despite no changes in ODM combine mode.
Reprogramming the stream would cause intermittent black screen on
display which could only be recovered through enable/disable sequence.

[HOW]
Fixed bug where we detected a change in ODM combine mode despite ODM
combine mode being disabled. Also removed code which required stream to
be reprogrammed once a change in ODM combine mode was noticed. Lastly we
do not support dynamic ODM switching for HDMI TMDS and FRL on DCN32,
therefore we never want to change its ODM policy.

Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix odm 2:1 policy not being applied consistently in 4k144 modes

[Why]
odm 2:1 policy is splitting the pipes in 4k144.
then in subvp code, we merge the pipes. but since the
 configuration is unsupported, we keep the pipes split

[How]
for unsupported subvp configuration, redo the dml and
 pipe split calls

Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: do not change pipe split policy for RV2

[Why]
RV2 do not change pipe split policy in the
minimal pipe split transition state.
This will unblock mode support on some
parts that limit to DPM0 for power reason.

[How]
Do not change pipe split policy in the
minimal pipe split transition state to
allow 4k multi display configs to be
supported at DPM0.

Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.199

This verion brings along following fixes:
-Add scaling factor for SubVP
-Modify stop_dbg_mode return value
-Add gfx_off members and document
-Add GFXOFF function for vangogh
-Add GFXOFF stats to debug
-Fix codestyle problems
-Fix overflow on MIN_I64
-Fix Unneeded semicolon
-Fix comment typo
-Remove useless condition in amdgpu_job_stop_all_jobs_on_sched()
-Add decoder_iv_ts helper for ih_v6
-Add chip version to DCN32
-Avoid doing vm_init multiple time
-Modify size calculation in MALL
-Fix DSC for phantom pipes
-Update clock table policy for DCN314
-Modify header inclusion pattern
-Fix plug/unplug external monitor will playback MPO video
-Add debug parameter to retain default clock table
-Increase tlb flush timeout for sriov
-Fix compare intergers of different widths
-Add reserved dc_log_type
-Fix pixel clock programming

Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.130.0

- For SubVP add scaling factor to allow firmware to calculate
 accurate line to start programming

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: skip set_topology_info for VF

Skip set_topology_info as xgmi TA will now block it
and host needs to program it.

Signed-off-by: Vignesh Chander <Vignesh.Chander@amd.com>
Reviewed-By : Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add sdma instance check for gfx11 CGCG

For some ASICs, like GFX IP v11.0.1, only have one SDMA instance,
so not need to configure SDMA1_RLC_CGCG_CTRL for this case.

Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove unneeded defines from bios parser

Removes DEFINEs that should have been removed after they were
introduced to ObjectID.h by the commit abea57d70e90
("drm/amdgpu: Add BRACKET_LAYOUT_ENUMs to ObjectID.h")

Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: enable PCON support for dcn314

[Why]
DCN314 supports PCON.

[How]
Explicitly enable it in dcn314 resources.

Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable NBIO IP v7.7.0 Clock Gating

Enable AMD_CG_SUPPORT_BIF_MGCG and AMD_CG_SUPPORT_BIF_LS support.

Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add NBIO IP v7.7.0 Clock Gating support

Add BIF Clock Gating MGCG and LS support for NBIO IP v7.7.0.

Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add TX_POWER_CTRL_1 macro definitions for NBIO IP v7.7.0

Add the BIF0_PCIE_TX_POWER_CTRL_1 register offset and mask macro
definitions for AMD_CG_SUPPORT_BIF_LS.

Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: add a force flush to delay work when radeon

Although radeon card fence and wait for gpu to finish processing current batch rings,
there is still a corner case that radeon lockup work queue may not be fully flushed,
and meanwhile the radeon_suspend_kms() function has called pci_set_power_state() to
put device in D3hot state.
Per PCI spec rev 4.0 on 5.3.1.4.1 D3hot State.
> Configuration and Message requests are the only TLPs accepted by a Function in
> the D3hot state. All other received Requests must be handled as Unsupported Requests,
> and all received Completions may optionally be handled as Unexpected Completions.
This issue will happen in following logs:
Unable to handle kernel paging request at virtual address 00008800e0008010
CPU 0 kworker/0:3(131): Oops 0
pc = [<ffffffff811bea5c>]  ra = [<ffffffff81240844>]  ps = 0000 Tainted: G        W
pc is at si_gpu_check_soft_reset+0x3c/0x240
ra is at si_dma_is_lockup+0x34/0xd0
v0 = 0000000000000000  t0 = fff08800e0008010  t1 = 0000000000010000
t2 = 0000000000008010  t3 = fff00007e3c00000  t4 = fff00007e3c00258
t5 = 000000000000ffff  t6 = 0000000000000001  t7 = fff00007ef078000
s0 = fff00007e3c016e8  s1 = fff00007e3c00000  s2 = fff00007e3c00018
s3 = fff00007e3c00000  s4 = fff00007fff59d80  s5 = 0000000000000000
s6 = fff00007ef07bd98
a0 = fff00007e3c00000  a1 = fff00007e3c016e8  a2 = 0000000000000008
a3 = 0000000000000001  a4 = 8f5c28f5c28f5c29  a5 = ffffffff810f4338
t8 = 0000000000000275  t9 = ffffffff809b66f8  t10 = ff6769c5d964b800
t11= 000000000000b886  pv = ffffffff811bea20  at = 0000000000000000
gp = ffffffff81d89690  sp = 00000000aa814126
Disabling lock debugging due to kernel taint
Trace:
[<ffffffff81240844>] si_dma_is_lockup+0x34/0xd0
[<ffffffff81119610>] radeon_fence_check_lockup+0xd0/0x290
[<ffffffff80977010>] process_one_work+0x280/0x550
[<ffffffff80977350>] worker_thread+0x70/0x7c0
[<ffffffff80977410>] worker_thread+0x130/0x7c0
[<ffffffff80982040>] kthread+0x200/0x210
[<ffffffff809772e0>] worker_thread+0x0/0x7c0
[<ffffffff80981f8c>] kthread+0x14c/0x210
[<ffffffff80911658>] ret_from_kernel_thread+0x18/0x20
[<ffffffff80981e40>] kthread+0x0/0x210
 Code: ad3e0008  43f0074a  ad7e0018  ad9e0020  8c3001e8  40230101
 <88210000> 4821ed21
So force lockup work queue flush to fix this problem.

Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Zhenneng Li <lizhenneng@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove unused header

dml_wrapper* files were removed in commit 01b537eeb049
("drm/amd/display: Remove unused code"), as they are not used anywhere.
However, the header file wasn't removed, so remove the header as well.

Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Include missing header

The file amdgpu_dm_plane.c missed the header amdgpu_dm_plane.h, which
resulted on the following warning:

drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:1046:5:
warning: no previous prototype for 'fill_dc_scaling_info'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:1222:6:
warning: no previous prototype for 'handle_cursor_update'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:152:6:
warning: no previous prototype for 'modifier_has_dcc'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:1576:5:
warning: no previous prototype for 'amdgpu_dm_plane_init'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:157:10:
warning: no previous prototype for 'modifier_gfx9_swizzle_mode'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:752:5:
warning: no previous prototype for 'fill_plane_buffer_attributes'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:83:31:
warning: no previous prototype for 'amd_get_format_info'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:88:6:
warning: no previous prototype for 'fill_blending_from_plane_state'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:992:5:
warning: no previous prototype for 'dm_plane_helper_check_state'
[-Wmissing-prototypes]

Therefore, include the missing header on the file and turn global functions
that are not used outside of the file into static functions.

Fixes: 5d945cbcd4b1 ("drm/amd/display: Create a file dedicated to planes")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove unneeded semicolon

Semicolon is not required after curly braces.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=1918
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix i386 frame size warning

Addresses the following warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn30/display_mode_vba_30.c:3596:6: error: stack frame size (2092) exceeds limit (2048) in 'dml30_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
void dml30_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
     ^

UseMinimumDCFCLK() is eating away at
dml30_ModeSupportAndSystemConfigurationFull()'s stack space, so use a
pointer to struct vba_vars_st instead of passing lots of large arrays
as parameters by value.

Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Remove the additional kfd pre reset call for sriov

The additional call is caused by merge conflict

Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Check num_gfx_rings for gfx v9_0 rb setup.

No need to set up rb when no gfx rings.

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix hive reference leak when adding xgmi device

Only amdgpu_get_xgmi_hive but no amdgpu_put_xgmi_hive
which will leak the hive reference.

Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Move psp_xgmi_terminate call from amdgpu_xgmi_remove_device to psp_hw_fini

V1:
The amdgpu_xgmi_remove_device function will send unload command
to psp through psp ring to terminate xgmi, but psp ring has been
destroyed in psp_hw_fini.

V2:
1. Change the commit title.
2. Restore amdgpu_xgmi_remove_device to its original calling location.
   Move psp_xgmi_terminate call from amdgpu_xgmi_remove_device to
   psp_hw_fini.

Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable GFXOFF allow control for GC IP v11.0.1

Enable GFXOFF allow control when set the GFX power gating.

Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Document gfx_off members of struct amdgpu_gfx

Add comments to document gfx_off related members of struct amdgpu_gfx.

Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Documentation/gpu: Document GFXOFF's count and residency

Add documentation explaining those two new files.

While here, add a note about the value type.

Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: Implement GFXOFF's entry count and residency for vangogh

Implement functions to get and set GFXOFF's entry count and residency
for vangogh.

Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd: Add detailed GFXOFF stats to debugfs

Add debugfs interface to log GFXOFF statistics:

- Read amdgpu_gfxoff_count to get the total GFXOFF entry count at the
  time of query since system power-up

- Write 1 to amdgpu_gfxoff_residency to start logging, and 0 to stop.
  Read it to get average GFXOFF residency % multiplied by 100
  during the last logging interval.

Both features are designed to be keep the values persistent between
suspends.

Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix minor codestyle problems

Fixes five checkpatch warnings:

CHECK: Please don't use multiple blank lines
+
+

ERROR: Macros with complex values should be enclosed in parentheses
+#define MAX_I64 \
+       (int64_t)((1ULL << 63) - 1)

WARNING: Missing a blank line after declarations
+       struct bw_fixed res;
+       ASSERT(value < BW_FIXED_MAX_I32 && value > BW_FIXED_MIN_I32);

ERROR: that open brace { should be on the previous line
+               do
+               {

ERROR: that open brace { should be on the previous line
+                       if (remainder >= arg2_value)
+                       {

Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix overflow on MIN_I64 definition

The definition of MIN_I64 in bw_fixed.c can cause gcc to whinge about
integer overflow, because it is treated as a positive value, which is
then negated. The temporary positive value is not necessarily
representable.

This causes the following warning:
../drivers/gpu/drm/amd/amdgpu/../display/dc/dml/calcs/bw_fixed.c:30:19:
warning: integer overflow in expression ‘-9223372036854775808’ of type
‘long long int’ results in ‘-9223372036854775808’ [-Woverflow]
  30 |         (int64_t)(-(1LL << 63))
     |                   ^

Writing out (-MAX_I64 - 1) works instead.

Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Unneeded semicolon

There is no semicolon after '}' in line 510.

Signed-off-by: min tang <tangmin@cdjrlc.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix comment typo

The double `aligned' is duplicated in line 1070, remove one.

Signed-off-by: min tang <tangmin@cdjrlc.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Remove unused code

We have some old code associated with DML, which we had plans to use,
but at some point, we just moved away from it. This commit removes the
dml_wrapper* files since they are not used anymore.

Reported-by: Magali Lemes <magalilemes00@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use sjt mec fw on aldebaran for sriov

The second jump table is required on live migration or mulitple VF
configuration on Aldebaran. With this implemented, the first level
jump table(hw used) will be same, mec fw internal will use the
second level jump table jump to the real functionality implementation.
so the different VF can load different version of MEC as long as
they support sjt

Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: include soc._clock_tmp[] into DC's scratch region

Currently, we are using soc._clock_tmp[] to temporarily store and modify
data from soc.clock_limits[] before copying it back into
soc.clock_limits[] (because modifying data directly in
soc.clock_limits[] causes unintended behavior). However, this approach
has a number of downsides, such as:

1. struct _vcs_dpi_soc_bounding_box_st's creation/destruction
   aren't well defined (which could mean more unintended
   behavior).
2. Throwing "temp" varibles in structs everywhere doesn't make
   for a particularly readable codebase.

For these reasons, we should get rid of soc._clock_tmp[] by defining a
struct scratch within struct dc that, contains within it all of the
temporary variables (including _clock_tmp[]) such that it is obvious how
they are intended to be used.

Co-authored-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>