OSDN Git Service
David S. Miller [Wed, 11 Jan 2017 02:34:03 +0000 (21:34 -0500)]
Merge branch 'mlx5-fixes'
Saeed Mahameed says:
====================
Mellanox mlx5 fixes and cleanups 2017-01-10
This series includes some mlx5e general cleanups from Daniel, Gil, Hadar
and myself.
Also it includes some critical mlx5e TC offloads fixes from Or Gerlitz.
For -stable:
- net/mlx5e: Remove WARN_ONCE from adaptive moderation code
Although this fix doesn't affect any functionality, I thought it is
better to clean this -WARN_ONCE- up for -stable in case someone hits
such corner case.
Please apply and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Jurgens [Tue, 10 Jan 2017 20:33:39 +0000 (22:33 +0200)]
net/mlx5: Only cancel recovery work when cleaning up device
Do not attempt to drain the health workqueue when unloading the device in
the recovery flow, this can cause a deadlock when the recovery work
tries to cancel itself with sync.
Because the work is no longer unconditionally canceled when unloading, it
must be explicitly canceled in the AER flow.
fixes:
689a248df83b ("net/mlx5: Cancel recovery work in remove flow")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gil Rockah [Tue, 10 Jan 2017 20:33:38 +0000 (22:33 +0200)]
net/mlx5e: Remove WARN_ONCE from adaptive moderation code
When trying to do interface down or changing interface configuration
under heavy traffic, some of the adaptive moderation corner cases can
occur and leave a WARN_ONCE call trace in the kernel log.
Those WARN_ONCE are meant for debug only, and should have been inserted
only under debug. We avoid such call traces by removing those WARN_ONCE.
Fixes:
cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Gil Rockah <gilr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 10 Jan 2017 20:33:37 +0000 (22:33 +0200)]
net/mlx5e: Un-register uplink representor on nic_disable
The code before this patch registered uplink e-Switch representor
on nic_enable and unregistered on nic_cleanup, the right place
for this unregister is in nic_disable.
Fixes:
127ea380acc9 ("net/mlx5: Add Representors registration API")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 10 Jan 2017 20:33:36 +0000 (22:33 +0200)]
net/mlx5e: Properly handle FW errors while adding TC rules
When the firmware returns an error (common example is an attempt to
add twice the same rule which is refused by the some FWs), we are not
properly derefing/cleaning few resources allocated on the way.
Examples are vport vlan deref under eswitch vlan offloads, and encap
entry/neighbour deref under eswitch encapsulation offloads, fix that.
Fixes:
a54e20b4fcae ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Fixes:
8b32580df1cb ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Tue, 10 Jan 2017 20:33:35 +0000 (22:33 +0200)]
net/mlx5e: Fix kbuild warnings for uninitialized parameters
kbuild warn about parameters that may be used uninitialized, fix it.
Fixes:
a54e20b4fcae ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 10 Jan 2017 20:33:34 +0000 (22:33 +0200)]
net/mlx5e: Set inline mode requirements for matching on IP fragments
For e-switch level matching on packets being an IP fragment, we
need to make sure the source vport inline mode is L3, fix that.
Fixes:
3f7d0eb42d59 ('net/mlx5e: Offload TC matching on packets being IP fragments')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 10 Jan 2017 20:33:33 +0000 (22:33 +0200)]
net/mlx5e: Properly get address type of encapsulation IP headers
As done elsewhere in our TC/flower offload code, the address type of
the encapsulation IP headers should be realized accroding to the
addr_type field of the encapsulation control dissector key, do that.
Fixes:
bbd00f7e2349 ('net/mlx5e: Add TC tunnel release action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 10 Jan 2017 20:33:32 +0000 (22:33 +0200)]
net/mlx5e: TC ipv4 tunnel encap offload error flow fixes
When the route lookup fails we should return the actual error.
When the neigh isn't valid, we should return -EOPNOTSUPP as done
in similar cases along the code.
When the offload can't take place as of invalid neigh etc, we
must release the neigh.
Fixes:
a54e20b4fcae ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 10 Jan 2017 20:33:31 +0000 (22:33 +0200)]
net/mlx5e: Warn when rejecting offload attempts of IP tunnels
We silently reject offloading of IPv6 tunnels, non vxlan tunnels,
vxlan tunnels where the dst port to match is not provided, etc.
Be a bit more verbose and print a warning so the user better
realizes what went wrong here and can fix it.
Fixes:
a54e20b4fcae ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Fixes:
bbd00f7e2349 ('net/mlx5e: Add TC tunnel release action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Tue, 10 Jan 2017 20:33:30 +0000 (22:33 +0200)]
net/mlx5e: Properly handle offloading of source udp port for IP tunnels
We can offload the matching on source udp port of ip tunnels for
decapsulation. We can not offload setting source udp port for tunnels
as part of encapsulation. Fix both the code that deals with matching
offload (decap) and the code that deal with encap offload to align with
that.
Fixes:
a54e20b4fcae ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Fixes:
bbd00f7e2349 ('net/mlx5e: Add TC tunnel release action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 10 Jan 2017 20:24:15 +0000 (12:24 -0800)]
gro: Disable frag0 optimization on IPv6 ext headers
The GRO fast path caches the frag0 address. This address becomes
invalid if frag0 is modified by pskb_may_pull or its variants.
So whenever that happens we must disable the frag0 optimization.
This is usually done through the combination of gro_header_hard
and gro_header_slow, however, the IPv6 extension header path did
the pulling directly and would continue to use the GRO fast path
incorrectly.
This patch fixes it by disabling the fast path when we enter the
IPv6 extension header path.
Fixes:
78a478d0efd9 ("gro: Inline skb_gro_header and cache frag0 virtual address")
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 10 Jan 2017 20:24:01 +0000 (12:24 -0800)]
gro: Enter slow-path if there is no tailroom
The GRO path has a fast-path where we avoid calling pskb_may_pull
and pskb_expand by directly accessing frag0. However, this should
only be done if we have enough tailroom in the skb as otherwise
we'll have to expand it later anyway.
This patch adds the check by capping frag0_len with the skb tailroom.
Fixes:
cb18978cbf45 ("gro: Open-code final pskb_may_pull")
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Tue, 10 Jan 2017 17:41:49 +0000 (09:41 -0800)]
mlx4: Return EOPNOTSUPP instead of ENOTSUPP
In commit
b45f0674b997 ("mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs"),
it changed EOPNOTSUPP to ENOTSUPP by mistake. This patch fixes it.
Fixes:
b45f0674b997 ("mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 10 Jan 2017 16:10:34 +0000 (17:10 +0100)]
net/af_iucv: don't use paged skbs for TX on HiperSockets
With commit
e53743994e21
("af_iucv: use paged SKBs for big outbound messages"),
we transmit paged skbs for both of AF_IUCV's transport modes
(IUCV or HiperSockets).
The qeth driver for Layer 3 HiperSockets currently doesn't
support NETIF_F_SG, so these skbs would just be linearized again
by the stack.
Avoid that overhead by using paged skbs only for IUCV transport.
cc stable, since this also circumvents a significant skb leak when
sending large messages (where the skb then needs to be linearized).
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # v4.8+
Fixes:
e53743994e21 ("af_iucv: use paged SKBs for big outbound messages")
Signed-off-by: David S. Miller <davem@davemloft.net>
Anna, Suman [Tue, 10 Jan 2017 03:48:56 +0000 (21:48 -0600)]
net: add the AF_QIPCRTR entries to family name tables
Commit
bdabad3e363d ("net: Add Qualcomm IPC router") introduced a
new address family. Update the family name tables accordingly so
that the lockdep initialization can use the proper names for this
family.
Cc: Courtney Cavin <courtney.cavin@sonymobile.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Boyd [Mon, 9 Jan 2017 22:31:58 +0000 (14:31 -0800)]
net: qrtr: Mark 'buf' as little endian
Failure to mark this pointer as __le32 causes checkers like
sparse to complain:
net/qrtr/qrtr.c:274:16: warning: incorrect type in assignment (different base types)
net/qrtr/qrtr.c:274:16: expected unsigned int [unsigned] [usertype] <noident>
net/qrtr/qrtr.c:274:16: got restricted __le32 [usertype] <noident>
net/qrtr/qrtr.c:275:16: warning: incorrect type in assignment (different base types)
net/qrtr/qrtr.c:275:16: expected unsigned int [unsigned] [usertype] <noident>
net/qrtr/qrtr.c:275:16: got restricted __le32 [usertype] <noident>
net/qrtr/qrtr.c:276:16: warning: incorrect type in assignment (different base types)
net/qrtr/qrtr.c:276:16: expected unsigned int [unsigned] [usertype] <noident>
net/qrtr/qrtr.c:276:16: got restricted __le32 [usertype] <noident>
Silence it.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 9 Jan 2017 19:58:34 +0000 (11:58 -0800)]
net: dsa: Ensure validity of dst->ds[0]
It is perfectly possible to have non zero indexed switches being present
in a DSA switch tree, in such a case, we will be deferencing a NULL
pointer while dsa_cpu_port_ethtool_{setup,restore}. Be more defensive
and ensure that dst->ds[0] is valid before doing anything with it.
Fixes:
0c73c523cf73 ("net: dsa: Initialize CPU port ethtool ops per tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Jan 2017 19:18:01 +0000 (11:18 -0800)]
net: skb_flow_get_be16() can be static
Removes following sparse complain :
net/core/flow_dissector.c:70:8: warning: symbol 'skb_flow_get_be16'
was not declared. Should it be static?
Fixes:
972d3876faa8 ("flow dissector: ICMP support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 10 Jan 2017 16:46:47 +0000 (11:46 -0500)]
Merge branch 'r8152-fix-autosuspend'
Hayes Wang says:
====================
r8152: fix autosuspend issue
Avoid rx is split into two parts when runtime suspend occurs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Tue, 10 Jan 2017 09:04:07 +0000 (17:04 +0800)]
r8152: fix rx issue for runtime suspend
Pause the rx and make sure the rx fifo is empty when the autosuspend
occurs.
If the rx data comes when the driver is canceling the rx urb, the host
controller would stop getting the data from the device and continue
it after next rx urb is submitted. That is, one continuing data is
split into two different urb buffers. That let the driver take the
data as a rx descriptor, and unexpected behavior happens.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Tue, 10 Jan 2017 09:04:06 +0000 (17:04 +0800)]
r8152: split rtl8152_suspend function
Split rtl8152_suspend() into rtl8152_system_suspend() and
rtl8152_rumtime_suspend().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 10 Jan 2017 08:30:51 +0000 (09:30 +0100)]
net: socket: Make unnecessarily global sockfs_setattr() static
Make sockfs_setattr() static as it is not used outside of net/socket.c
This fixes the following GCC warning:
net/socket.c:534:5: warning: no previous prototype for ‘sockfs_setattr’ [-Wmissing-prototypes]
Fixes:
86741ec25462 ("net: core: Add a UID field to struct sock.")
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 10 Jan 2017 16:27:46 +0000 (11:27 -0500)]
Merge tag 'wireless-drivers-for-davem-2017-01-10' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.10
Only two fixes at this time. The rtlwifi fix is an important one as it
fixes a reported oops and Linus was already asking about it. The
orinoco fix is not tested on a real device, because it's old legacy
hardware and hardly no-one use it, but it should fix a (theoretical)
issue with VMAP_STACK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Jan 2017 16:51:32 +0000 (08:51 -0800)]
tcp: do not export tcp_peer_is_proven()
After commit
1fb6f159fd21 ("tcp: add tcp_conn_request"),
tcp_peer_is_proven() no longer needs to be exported.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Mon, 9 Jan 2017 14:17:27 +0000 (15:17 +0100)]
net: phy: Add Meson GXL PHY hardware dependency
As I understand it the Meson GXL PHY driver is only useful on one
architecture so only make it visible on that architecture.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes:
7334b3e47aee ("net: phy: Add Meson GXL Internal PHY driver")
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Tsyrklevich [Mon, 9 Jan 2017 13:57:48 +0000 (20:57 +0700)]
net/appletalk: Fix kernel memory disclosure
ipddp_route structs contain alignment padding so kernel heap memory
is leaked when they are copied to user space in
ipddp_ioctl(SIOCFINDIPDDPRT). Change kmalloc() to kzalloc() to clear
that memory.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Tikhomirov [Mon, 9 Jan 2017 07:45:49 +0000 (10:45 +0300)]
ipv4: make tcp_notsent_lowat sysctl knob behave as true unsigned int
> cat /proc/sys/net/ipv4/tcp_notsent_lowat
-1
> echo
4294967295 > /proc/sys/net/ipv4/tcp_notsent_lowat
-bash: echo: write error: Invalid argument
> echo -
2147483648 > /proc/sys/net/ipv4/tcp_notsent_lowat
> cat /proc/sys/net/ipv4/tcp_notsent_lowat
-
2147483648
but in documentation we have "tcp_notsent_lowat - UNSIGNED INTEGER"
v2: simplify to just proc_douintvec
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Alemayhu [Sat, 7 Jan 2017 22:53:00 +0000 (23:53 +0100)]
ipv6: fix typos
o s/approriate/appropriate
o s/discouvery/discovery
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zefir Kurtisi [Fri, 6 Jan 2017 11:14:48 +0000 (12:14 +0100)]
phy state machine: failsafe leave invalid RUNNING state
While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().
If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.
This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.
This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 9 Jan 2017 19:58:28 +0000 (11:58 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix dumping of nft_quota entries, from Pablo Neira Ayuso.
2) Fix out of bounds access in nf_tables discovered by KASAN, from
Florian Westphal.
3) Fix IRQ enabling in dp83867 driver, from Grygorii Strashko.
4) Fix unicast filtering in be2net driver, from Ivan Vecera.
5) tg3_get_stats64() can race with driver close and ethtool
reconfigurations, fix from Michael Chan.
6) Fix error handling when pass limit is reached in bpf code gen on
x86. From Daniel Borkmann.
7) Don't clobber switch ops and use proper MDIO nested reads and writes
in bcm_sf2 driver, from Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
net: dsa: bcm_sf2: Utilize nested MDIO read/write
net: dsa: bcm_sf2: Do not clobber b53_switch_ops
net: stmmac: fix maxmtu assignment to be within valid range
bpf: change back to orig prog on too many passes
tg3: Fix race condition in tg3_get_stats64().
be2net: fix unicast list filling
be2net: fix accesses to unicast list
netlabel: add CALIPSO to the list of built-in protocols
vti6: fix device register to report IFLA_INFO_KIND
net: phy: dp83867: fix irq generation
amd-xgbe: Fix IRQ processing when running in single IRQ mode
sh_eth: R8A7740 supports packet shecksumming
sh_eth: fix EESIPR values for SH77{34|63}
r8169: fix the typo in the comment
nl80211: fix sched scan netlink socket owner destruction
bridge: netfilter: Fix dropping packets that moving through bridge interface
netfilter: ipt_CLUSTERIP: check duplicate config when initializing
netfilter: nft_payload: mangle ckecksum if NFT_PAYLOAD_L4CSUM_PSEUDOHDR is set
netfilter: nf_tables: fix oob access
netfilter: nft_queue: use raw_smp_processor_id()
...
David S. Miller [Mon, 9 Jan 2017 03:01:22 +0000 (22:01 -0500)]
Merge branch 'bcm_sf2-fixes'
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Couple fixes
Here are a couple of fixes for bcm_sf2, please queue these up for -stable
as well, thank you very much!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 8 Jan 2017 05:01:57 +0000 (21:01 -0800)]
net: dsa: bcm_sf2: Utilize nested MDIO read/write
We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.
Fixes:
461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 8 Jan 2017 05:01:56 +0000 (21:01 -0800)]
net: dsa: bcm_sf2: Do not clobber b53_switch_ops
We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.
Fixes:
f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kweh, Hock Leong [Sat, 7 Jan 2017 09:32:03 +0000 (17:32 +0800)]
net: stmmac: fix maxmtu assignment to be within valid range
There is no checking valid value of maxmtu when getting it from
device tree. This resolution added the checking condition to
ensure the assignment is made within a valid range.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 8 Jan 2017 22:18:17 +0000 (14:18 -0800)]
Linux 4.10-rc3
Daniel Borkmann [Fri, 6 Jan 2017 23:26:33 +0000 (00:26 +0100)]
bpf: change back to orig prog on too many passes
If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.
Fixes:
959a75791603 ("bpf, x86: add support for constant blinding")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 8 Jan 2017 19:42:04 +0000 (11:42 -0800)]
Merge tag 'usb-4.10-rc3' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 4.10-rc3. Yeah, it's a lot, an
artifact of the holiday break I think.
Lots of gadget and the usual XHCI fixups for reported issues (one day
that driver will calm down...) Also included are a bunch of usb-serial
driver fixes, and for good measure, a number of much-reported MUSB
driver issues have finally been resolved.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (72 commits)
USB: fix problems with duplicate endpoint addresses
usb: ohci-at91: use descriptor-based gpio APIs correctly
usb: storage: unusual_uas: Add JMicron JMS56x to unusual device
usb: hub: Move hub_port_disable() to fix warning if PM is disabled
usb: musb: blackfin: add bfin_fifo_offset in bfin_ops
usb: musb: fix compilation warning on unused function
usb: musb: Fix trying to free already-free IRQ 4
usb: musb: dsps: implement clear_ep_rxintr() callback
usb: musb: core: add clear_ep_rxintr() to musb_platform_ops
USB: serial: ti_usb_3410_5052: fix NULL-deref at open
USB: serial: spcp8x5: fix NULL-deref at open
USB: serial: quatech2: fix sleep-while-atomic in close
USB: serial: pl2303: fix NULL-deref at open
USB: serial: oti6858: fix NULL-deref at open
USB: serial: omninet: fix NULL-derefs at open and disconnect
USB: serial: mos7840: fix misleading interrupt-URB comment
USB: serial: mos7840: remove unused write URB
USB: serial: mos7840: fix NULL-deref at open
USB: serial: mos7720: remove obsolete port initialisation
USB: serial: mos7720: fix parallel probe
...
Linus Torvalds [Sun, 8 Jan 2017 19:37:44 +0000 (11:37 -0800)]
Merge tag 'char-misc-4.10-rc3' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are a few small char/misc driver fixes for 4.10-rc3.
Two MEI driver fixes, and three NVMEM patches for reported issues, and
a new Hyper-V driver MAINTAINER update. Nothing major at all, all have
been in linux-next with no reported issues"
* tag 'char-misc-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
hyper-v: Add myself as additional MAINTAINER
nvmem: fix nvmem_cell_read() return type doc
nvmem: imx-ocotp: Fix wrong register size
nvmem: qfprom: Allow single byte accesses for read/write
mei: move write cb to completion on credentials failures
mei: bus: fix mei_cldev_enable KDoc
Linus Torvalds [Sun, 8 Jan 2017 19:22:00 +0000 (11:22 -0800)]
Merge tag 'staging-4.10-rc3' of git://git./linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and IIO driver fixes for 4.10-rc3.
Most of these are minor IIO fixes of reported issues, along with one
network driver fix to resolve an issue. And a MAINTAINERS update with
a new mailing list. All of these, except the MAINTAINERS file update,
have been in linux-next with no reported issues (the MAINTAINERS patch
happened on Friday...)"
* tag 'staging-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
MAINTAINERS: add greybus subsystem mailing list
staging: octeon: Call SET_NETDEV_DEV()
iio: accel: st_accel: fix LIS3LV02 reading and scaling
iio: common: st_sensors: fix channel data parsing
iio: max44000: correct value in illuminance_integration_time_available
iio: adc: TI_AM335X_ADC should depend on HAS_DMA
iio: bmi160: Fix time needed to sleep after command execution
iio: 104-quad-8: Fix active level mismatch for the preset enable option
iio: 104-quad-8: Fix off-by-one errors when addressing IOR
iio: 104-quad-8: Fix index control configuration
Michael Chan [Fri, 6 Jan 2017 21:18:53 +0000 (16:18 -0500)]
tg3: Fix race condition in tg3_get_stats64().
The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations. Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block. tg3_get_stats64() is
already taking tp->lock.
Reported-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Fri, 6 Jan 2017 20:59:30 +0000 (21:59 +0100)]
be2net: fix unicast list filling
The adapter->pmac_id[0] item is used for primary MAC address but
this is not true for adapter->uc_list[0] as is assumed in
be_set_uc_list(). There are N UC addresses copied first from net_device
to adapter->uc_list[1..N] and then N UC addresses from
adapter->uc_list[0..N-1] are sent to HW. So the last UC address is never
stored into HW and address 00:00:00:00;00:00 (from uc_list[0]) is used
instead.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes:
b717241 be2net: replace polling with sleeping in the FW completion path
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Weiner [Sat, 7 Jan 2017 00:21:43 +0000 (19:21 -0500)]
mm: workingset: fix use-after-free in shadow node shrinker
Several people report seeing warnings about inconsistent radix tree
nodes followed by crashes in the workingset code, which all looked like
use-after-free access from the shadow node shrinker.
Dave Jones managed to reproduce the issue with a debug patch applied,
which confirmed that the radix tree shrinking indeed frees shadow nodes
while they are still linked to the shadow LRU:
WARNING: CPU: 2 PID: 53 at lib/radix-tree.c:643 delete_node+0x1e4/0x200
CPU: 2 PID: 53 Comm: kswapd0 Not tainted 4.10.0-rc2-think+ #3
Call Trace:
delete_node+0x1e4/0x200
__radix_tree_delete_node+0xd/0x10
shadow_lru_isolate+0xe6/0x220
__list_lru_walk_one.isra.4+0x9b/0x190
list_lru_walk_one+0x23/0x30
scan_shadow_nodes+0x2e/0x40
shrink_slab.part.44+0x23d/0x5d0
shrink_node+0x22c/0x330
kswapd+0x392/0x8f0
This is the WARN_ON_ONCE(!list_empty(&node->private_list)) placed in the
inlined radix_tree_shrink().
The problem is with
14b468791fa9 ("mm: workingset: move shadow entry
tracking to radix tree exceptional tracking"), which passes an update
callback into the radix tree to link and unlink shadow leaf nodes when
tree entries change, but forgot to pass the callback when reclaiming a
shadow node.
While the reclaimed shadow node itself is unlinked by the shrinker, its
deletion from the tree can cause the left-most leaf node in the tree to
be shrunk. If that happens to be a shadow node as well, we don't unlink
it from the LRU as we should.
Consider this tree, where the s are shadow entries:
root->rnode
|
[0 n]
| |
[s ] [sssss]
Now the shadow node shrinker reclaims the rightmost leaf node through
the shadow node LRU:
root->rnode
|
[0 ]
|
[s ]
Because the parent of the deleted node is the first level below the
root and has only one child in the left-most slot, the intermediate
level is shrunk and the node containing the single shadow is put in
its place:
root->rnode
|
[s ]
The shrinker again sees a single left-most slot in a first level node
and thus decides to store the shadow in root->rnode directly and free
the node - which is a leaf node on the shadow node LRU.
root->rnode
|
s
Without the update callback, the freed node remains on the shadow LRU,
where it causes later shrinker runs to crash.
Pass the node updater callback into __radix_tree_delete_node() in case
the deletion causes the left-most branch in the tree to collapse too.
Also add warnings when linked nodes are freed right away, rather than
wait for the use-after-free when the list is scanned much later.
Fixes:
14b468791fa9 ("mm: workingset: move shadow entry tracking to radix tree exceptional tracking")
Reported-by: Dave Chinner <david@fromorbit.com>
Reported-by: Hugh Dickins <hughd@google.com>
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-and-tested-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chris Leech <cleech@redhat.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox <mawilcox@linuxonhyperv.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Sat, 7 Jan 2017 23:37:31 +0000 (15:37 -0800)]
mm: stop leaking PageTables
4.10-rc loadtest (even on x86, and even without THPCache) fails with
"fork: Cannot allocate memory" or some such; and /proc/meminfo shows
PageTables growing.
Commit
953c66c2b22a ("mm: THP page cache support for ppc64") that got
merged in rc1 removed the freeing of an unused preallocated pagetable
after do_fault_around() has called map_pages().
This is usually a good optimization, so that the followup doesn't have
to reallocate one; but it's not sufficient to shift the freeing into
alloc_set_pte(), since there are failure cases (most commonly
VM_FAULT_RETRY) which never reach finish_fault().
Check and free it at the outer level in do_fault(), then we don't need
to worry in alloc_set_pte(), and can restore that to how it was (I
cannot find any reason to pte_free() under lock as it was doing).
And fix a separate pagetable leak, or crash, introduced by the same
change, that could only show up on some ppc64: why does do_set_pmd()'s
failure case attempt to withdraw a pagetable when it never deposited
one, at the same time overwriting (so leaking) the vmf->prealloc_pte?
Residue of an earlier implementation, perhaps? Delete it.
Fixes:
953c66c2b22a ("mm: THP page cache support for ppc64")
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 7 Jan 2017 17:47:43 +0000 (09:47 -0800)]
Merge branch 'rc-fixes' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"The asm-prototypes.h file added in the last merge window results in
invalid code with CONFIG_KMEMCHECK=y. The net result is that genksyms
segfaults.
This pull request fixes the header, the genksyms fix is in my kbuild
branch for 4.11"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
asm-prototypes: Clear any CPP defines before declaring the functions
Greg Kroah-Hartman [Fri, 6 Jan 2017 07:20:03 +0000 (08:20 +0100)]
MAINTAINERS: add greybus subsystem mailing list
The Greybus driver subsystem has a mailing list, so list it in the
MAINTAINERS file so that people know to send patches there as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ivan Vecera [Fri, 6 Jan 2017 19:30:02 +0000 (20:30 +0100)]
be2net: fix accesses to unicast list
Commit
988d44b "be2net: Avoid redundant addition of mac address in HW"
introduced be_dev_mac_add & be_uc_mac_add helpers that incorrectly
access adapter->uc_list as an array of bytes instead of an array of
be_eth_addr. Consequently NIC is not filled with valid data so unicast
filtering is broken.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes:
988d44b be2net: Avoid redundant addition of mac address in HW
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Fri, 6 Jan 2017 19:26:54 +0000 (14:26 -0500)]
netlabel: add CALIPSO to the list of built-in protocols
When we added CALIPSO support in Linux v4.8 we forgot to add it to the
list of supported protocols with display at boot.
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 6 Jan 2017 23:38:39 +0000 (15:38 -0800)]
Merge tag 'sound-4.10-rc3' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing particular stands out, only a few small fixes for USB-audio,
HD-audio and Firewire. The USB-audio fix is the respin of the previous
race fix after a revert due to the regression"
* tag 'sound-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: firewire-lib: change structure member with proper type"
ALSA: usb-audio: test EP_FLAG_RUNNING at urb completion
ALSA: usb-audio: Fix irq/process data synchronization
ALSA: hda - Apply asus-mode8 fixup to ASUS X71SL
ALSA: hda - Fix up GPIO for ASUS ROG Ranger
ALSA: firewire-lib: change structure member with proper type
ALSA: firewire-tascam: Fix to handle error from initialization of stream data
ALSA: fireworks: fix asymmetric API call at unit removal
Linus Torvalds [Fri, 6 Jan 2017 23:35:27 +0000 (15:35 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One fix for a broken driver on Renesas RZ/A1 SoCs with bootloaders
that don't turn all the clks on and another fix for stm32f4 SoCs where
we have multiple drivers attaching to the same DT node"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: stm32f4: Use CLK_OF_DECLARE_DRIVER initialization method
clk: renesas: mstp: Support 8-bit registers for r7s72100
Linus Torvalds [Fri, 6 Jan 2017 23:32:40 +0000 (15:32 -0800)]
Merge tag 'hwmon-for-linus-v4.10-rc3' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix temp1_max_alarm attribute in lm90 driver"
* tag 'hwmon-for-linus-v4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (lm90) fix temp1_max_alarm attribute
Linus Torvalds [Fri, 6 Jan 2017 23:27:17 +0000 (15:27 -0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"MIPS:
- fix host kernel crashes when receiving a signal with 64-bit
userspace
- flush instruction cache on all vcpus after generating entry code
(both for stable)
x86:
- fix NULL dereference in MMU caused by SMM transitions (for stable)
- correct guest instruction pointer after emulating some VMX errors
- minor cleanup"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: remove duplicated declaration
KVM: MIPS: Flush KVM entry code from icache globally
KVM: MIPS: Don't clobber CP0_Status.UX
KVM: x86: reset MMU on KVM_SET_VCPU_EVENTS
KVM: nVMX: fix instruction skipping during emulated vm-entry
Linus Torvalds [Fri, 6 Jan 2017 23:18:58 +0000 (15:18 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- re-introduce the arm64 get_current() optimisation
- KERN_CONT fallout fix in show_pte()
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: restore get_current() optimisation
arm64: mm: fix show_pte KERN_CONT fallout
David S. Miller [Fri, 6 Jan 2017 21:26:19 +0000 (16:26 -0500)]
Merge tag 'mac80211-for-davem-2017-01-06' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another single fix, to correctly handle destruction of a
single netlink socket having ownership of multiple objects
(scheduled scan requests and interfaces.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Forster [Fri, 6 Jan 2017 10:27:59 +0000 (10:27 +0000)]
vti6: fix device register to report IFLA_INFO_KIND
vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
Signed-off-by: Dave Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko [Thu, 5 Jan 2017 20:48:07 +0000 (14:48 -0600)]
net: phy: dp83867: fix irq generation
For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.
Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lendacky, Thomas [Wed, 4 Jan 2017 21:07:16 +0000 (15:07 -0600)]
amd-xgbe: Fix IRQ processing when running in single IRQ mode
When running in single IRQ mode, the additional IRQ routines were being
skipped because only the XGMAC interrupt status was being checked.
Update the code so that the additional IRQ routines are checked whenever
an interrupt is received.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Wed, 4 Jan 2017 21:29:32 +0000 (00:29 +0300)]
sh_eth: R8A7740 supports packet shecksumming
The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data, thus CSMR isn't cleared...
Fixes:
73a0d907301e ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Wed, 4 Jan 2017 19:18:24 +0000 (22:18 +0300)]
sh_eth: fix EESIPR values for SH77{34|63}
As the SH77{34|63} manuals are freely available, I've checked the EESIPR
values written against the manuals, and they appeared to set the reserved
bits 11-15 (which should be 0 on write). Fix those EESIPR values.
Fixes:
380af9e390ec ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"")
Fixes:
f5d12767c8fd ("sh_eth: get SH77{34|63} support out of #ifdef")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 6 Jan 2017 19:19:03 +0000 (11:19 -0800)]
Merge tag 'vfio-v4.10-rc3' of git://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
- Add mtty sample driver properly into build system (Alex Williamson)
- Restore type1 mapping performance after mdev (Alex Williamson)
- Fix mdev device race (Alex Williamson)
- Cleanups to the mdev ABI used by vendor drivers (Alex Williamson)
- Build fix for old compilers (Arnd Bergmann)
- Fix sample driver error path (Dan Carpenter)
- Handle pci_iomap() error (Arvind Yadav)
- Fix mdev ioctl return type (Paul Gortmaker)
* tag 'vfio-v4.10-rc3' of git://github.com/awilliam/linux-vfio:
vfio-mdev: fix non-standard ioctl return val causing i386 build fail
vfio-pci: Handle error from pci_iomap
vfio-mdev: fix some error codes in the sample code
vfio-pci: use 32-bit comparisons for register address for gcc-4.5
vfio-mdev: Make mdev_device private and abstract interfaces
vfio-mdev: Make mdev_parent private
vfio-mdev: de-polute the namespace, rename parent_device & parent_ops
vfio-mdev: Fix remove race
vfio/type1: Restore mapping performance with mdev support
vfio-mdev: Fix mtty sample driver building
Linus Torvalds [Fri, 6 Jan 2017 18:53:21 +0000 (10:53 -0800)]
Merge branch 'stable/for-linus-4.10' of git://git./linux/kernel/git/konrad/swiotlb
Pull swiotlb fixes from Konrad Rzeszutek Wilk:
"This has one fix to make i915 work when using Xen SWIOTLB, and a
feature from Geert to aid in debugging of devices that can't do DMA
outside the 32-bit address space.
The feature from Geert is on top of v4.10 merge window commit
(specifically you pulling my previous branch), as his changes were
dependent on the Documentation/ movement patches.
I figured it would just easier than me trying than to cherry-pick the
Documentation patches to satisfy git.
The patches have been soaking since 12/20, albeit I updated the last
patch due to linux-next catching an compiler error and adding an
Tested-and-Reported-by tag"
* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Export swiotlb_max_segment to users
swiotlb: Add swiotlb=noforce debug option
swiotlb: Convert swiotlb_force from int to enum
x86, swiotlb: Simplify pci_swiotlb_detect_override()
Linus Torvalds [Fri, 6 Jan 2017 18:49:36 +0000 (10:49 -0800)]
Merge tag 'iommu-fixes-v4.10-rc2' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Three fixes queued up:
- fix an issue with command buffer overflow handling in the AMD IOMMU
driver
- add an additional context entry flush to the Intel VT-d driver to
make sure any old context entry from kdump copying is flushed out
of the cache
- correct the encoding of the PASID table size in the Intel VT-d
driver"
* tag 'iommu-fixes-v4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix the left value check of cmd buffer
iommu/vt-d: Fix pasid table size encoding
iommu/vt-d: Flush old iommu caches for kdump when the device gets context mapped
Linus Torvalds [Fri, 6 Jan 2017 18:40:17 +0000 (10:40 -0800)]
Merge tag 'acpi-4.10-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a device enumeration problem related to _ADR matching and an
IOMMU initialization issue related to the DMAR table missing, remove
an excessive function call from the core ACPI code, update an error
message in the ACPI WDAT watchdog driver and add a way to work around
problems with unhandled GPE notifications.
Specifics:
- Fix a device enumeration issue leading to incorrect associations
between ACPI device objects and platform device objects
representing physical devices if the given device object has both
_ADR and _HID (Rafael Wysocki).
- Avoid passing NULL to acpi_put_table() during IOMMU initialization
which triggers a (rightful) warning from ACPICA (Rafael Wysocki).
- Drop an excessive call to acpi_dma_deconfigure() from the core code
that binds ACPI device objects to device objects representing
physical devices (Lorenzo Pieralisi).
- Update an error message in the ACPI WDAT watchdog driver to make it
provide more useful information (Mika Westerberg).
- Add a mechanism to work around issues with unhandled GPE
notifications that occur during system initialization and cannot be
prevented by means of sysfs (Lv Zheng)"
* tag 'acpi-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / DMAR: Avoid passing NULL to acpi_put_table()
ACPI / scan: Prefer devices without _HID/_CID for _ADR matching
ACPI / watchdog: Print out error number when device creation fails
ACPI / sysfs: Provide quirk mechanism to prevent GPE flooding
ACPI: Drop misplaced acpi_dma_deconfigure() call from acpi_bind_one()
Linus Torvalds [Fri, 6 Jan 2017 18:37:50 +0000 (10:37 -0800)]
Merge tag 'pm-4.10-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a few issues in the intel_pstate driver, a documetation
issue, a false-positive compiler warning in the generic power domains
framework and two problems in the devfreq subsystem. They also update
the MAINTAINERS entry for devfreq and add a new "compatible" string to
the generic cpufreq-dt driver.
Specifics:
- Fix a few intel_pstate driver issues: add missing locking it two
places, avoid exposing a useless debugfs interface and keep the
attribute values in sysfs in sync (Rafael Wysocki).
- Drop confusing kernel-doc references related to power management
and ACPI from the driver API manual (Rafael Wysocki).
- Make a false-positive compiler warning in the generic power domains
framework go away (Augusto Mecking Caringi).
- Fix two initialization issues in the devfreq subsystem and update
the MAINTAINERS entry for it (Chanwoo Choi).
- Add a new "compatible" string for APM X-Gene 2 to the generic DT
cpufreq driver (Hoan Tran)"
* tag 'pm-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: dt: Add support for APM X-Gene 2
PM / devfreq: exynos-bus: Fix the wrong return value
PM / devfreq: Fix the bug of devfreq_add_device when governor is NULL
MAINTAINERS: Add myself as reviewer for DEVFREQ subsystem support
PM / docs: Drop confusing kernel-doc references from infrastructure.rst
PM / domains: Fix 'may be used uninitialized' build warning
cpufreq: intel_pstate: Always keep all limits settings in sync
cpufreq: intel_pstate: Use locking in intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Use locking in intel_pstate_resume()
cpufreq: intel_pstate: Do not expose PID parameters in passive mode
Konrad Rzeszutek Wilk [Tue, 20 Dec 2016 15:02:02 +0000 (10:02 -0500)]
swiotlb: Export swiotlb_max_segment to users
So they can figure out what is the optimal number of pages
that can be contingously stitched together without fear of
bounce buffer.
We also expose an mechanism for sub-users of SWIOTLB API, such
as Xen-SWIOTLB to set the max segment value. And lastly
if swiotlb=force is set (which mandates we bounce buffer everything)
we set max_segment so at least we can bounce buffer one 4K page
instead of a giant 512KB one for which we may not have space.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reported-and-Tested-by: Juergen Gross <jgross@suse.com>
Rafael J. Wysocki [Fri, 6 Jan 2017 13:36:30 +0000 (14:36 +0100)]
Merge branches 'acpi-scan', 'acpi-sysfs', 'acpi-wdat' and 'acpi-tables'
* acpi-scan:
ACPI / scan: Prefer devices without _HID/_CID for _ADR matching
ACPI: Drop misplaced acpi_dma_deconfigure() call from acpi_bind_one()
* acpi-sysfs:
ACPI / sysfs: Provide quirk mechanism to prevent GPE flooding
* acpi-wdat:
ACPI / watchdog: Print out error number when device creation fails
* acpi-tables:
ACPI / DMAR: Avoid passing NULL to acpi_put_table()
Rafael J. Wysocki [Fri, 6 Jan 2017 13:35:32 +0000 (14:35 +0100)]
Merge branches 'pm-domains', 'pm-docs' and 'pm-devfreq'
* pm-domains:
PM / domains: Fix 'may be used uninitialized' build warning
* pm-docs:
PM / docs: Drop confusing kernel-doc references from infrastructure.rst
* pm-devfreq:
PM / devfreq: exynos-bus: Fix the wrong return value
PM / devfreq: Fix the bug of devfreq_add_device when governor is NULL
MAINTAINERS: Add myself as reviewer for DEVFREQ subsystem support
Rafael J. Wysocki [Fri, 6 Jan 2017 13:34:52 +0000 (14:34 +0100)]
Merge branch 'pm-cpufreq'
* pm-cpufreq:
cpufreq: dt: Add support for APM X-Gene 2
cpufreq: intel_pstate: Always keep all limits settings in sync
cpufreq: intel_pstate: Use locking in intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Use locking in intel_pstate_resume()
cpufreq: intel_pstate: Do not expose PID parameters in passive mode
Linus Torvalds [Fri, 6 Jan 2017 07:17:41 +0000 (23:17 -0800)]
Merge tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Just two small fixes for platform drivers x86:
- use brightness_set_blocking for LED-setting callbacks on Fujitsu
laptops
- fix surface3_button build errors"
* tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: fujitsu-laptop: use brightness_set_blocking for LED-setting callbacks
platform/x86: fix surface3_button build errors
Linus Torvalds [Fri, 6 Jan 2017 07:06:06 +0000 (23:06 -0800)]
Merge branch 'stable-4.10' of git://git.infradead.org/users/pcmoore/audit
Pull audit fixes from Paul Moore:
"Two small fixes relating to audit's use of fsnotify.
The first patch plugs a leak and the second fixes some lock
shenanigans. The patches are small and I banged on this for an
afternoon with our testsuite and didn't see anything odd"
* 'stable-4.10' of git://git.infradead.org/users/pcmoore/audit:
audit: Fix sleep in atomic
fsnotify: Remove fsnotify_duplicate_mark()
Linus Torvalds [Thu, 5 Jan 2017 23:06:02 +0000 (15:06 -0800)]
Merge tag 'drm-intel-fixes-2017-01-05' of git://anongit.freedesktop.org/git/drm-intel
Pull i915 drm fixes from Jani Nikula:
"Here's a bunch of drm/i915 fixes for v4.10-rc3. It includes GVT-g
fixes.
My new year's resolution is to start using signed tags for pulls. If
that feels like a déjà vu, it's ((new year's) resolution), not (new
(year's resolution))"
[ Taking this directly from Jani because Dave Airlie is only partially
connected right now. - Linus ]
* tag 'drm-intel-fixes-2017-01-05' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Prevent timeline updates whilst performing reset
drm/i915: Silence allocation failure during sg_trim()
drm/i915: Don't clflush before release phys object
drm/i915: Fix oops in overlay due to frontbuffer tracking
drm/i915: Fix oopses in the overlay code due to i915_gem_active stuff
drm/i915: Initialize overlay->last_flip properly
drm/i915: Move the min_pixclk[] handling to the end of readout
drm/i915: Force VDD off on the new power seqeuencer before starting to use it
drm/i915/gvt: fix typo in cfg_space range check
drm/i915/gvt: fix an issue in emulating cfg space PCI_COMMAND
drm/i915/gvt/kvmgt: trival: code cleanup
drm/i915/gvt/kvmgt: prevent double-release of vgpu
drm/i915/gvt/kvmgt: check returned slot for gfn
drm/i915/gvt/kvmgt: dereference the pointer within lock
drm/i915/gvt: reset the GGTT entry when vGPU created
drm/i915/gvt: fix an error in opregion handling
Alan Stern [Mon, 19 Dec 2016 17:03:41 +0000 (12:03 -0500)]
USB: fix problems with duplicate endpoint addresses
When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses. This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:
WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...
CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<
ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<
ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179
[<
ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542
[<
ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
[<
ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
[<
ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
[< inline >] create_dir lib/kobject.c:71
[<
ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
[< inline >] kobject_add_varg lib/kobject.c:366
[<
ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411
[<
ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088
[<
ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206
[<
ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
[<
ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
[<
ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
[<
ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
[<
ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263
This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 5 Jan 2017 18:36:56 +0000 (10:36 -0800)]
Merge tag 'pinctrl-v4.10-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Three small pin control fixes for the v4.10 series. Very little to say
about them, just driver fixes.
- one fix to the AMD pinctrl ACPI glue
- fix requests on the Meson driver
- fix bitfield widths on Samsungs Exynos 5433"
* tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: samsung: Fix the width of PINCFG_TYPE_DRV bitfields for Exynos5433
pinctrl: meson: fix gpio request disabling other modes
pinctrl/amd: Set the level based on ACPI tables
Peter Rosin [Thu, 22 Dec 2016 07:43:55 +0000 (08:43 +0100)]
usb: ohci-at91: use descriptor-based gpio APIs correctly
The gpiod_get* function family does not want the -gpio suffix.
Use devm_gpiod_get_index_optional instead of devm_gpiod_get_optional.
The descriptor based APIs handle active high/low automatically.
The vbus-gpios are output, request enable while getting the gpio.
Don't try to get any vbus-gpios for ports outside num-ports.
WTF? Big sigh.
Fixes:
054d4b7b577d ("usb: ohci-at91: Use descriptor-based gpio APIs")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 5 Jan 2017 18:32:16 +0000 (10:32 -0800)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather large set of bugfixes, as we just returned from the
Christmas break. Most of these are relatively unimportant fixes for
regressions introduced during the merge window, and about half of the
changes are for mach-omap2.
A couple of patches are just cleanups and dead code removal that I
would not normally have considered for merging after -rc2, but I
decided to take them along with the fixes this time.
Notable fixes include:
- removing the skeleton.dtsi include broke a number of machines, and
we have to put empty /chosen nodes back to be able to pass kernel
command lines as before
- enabling Samsung platforms no longer hardwires CONFIG_HZ to 200, as
it had been for no good reason for a long time"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
MAINTAINERS: extend PSCI entry to cover the newly add PSCI checker code
drivers: psci: annotate timer on stack to silence odebug messages
ARM64: defconfig: enable DRM_MESON as module
ARM64: dts: meson-gx: Add Graphic Controller nodes
ARM64: dts: meson-gxl: fix GPIO include
ARM: dts: imx6: Disable "weim" node in the dtsi files
ARM: dts: qcom: apq8064: Add missing scm clock
ARM: davinci: da8xx: Fix sleeping function called from invalid context
ARM: davinci: Make __clk_{enable,disable} functions public
ARM: davinci: da850: don't add emac clock to lookup table twice
ARM: davinci: da850: fix infinite loop in clk_set_rate()
ARM: i.MX: remove map_io callback
ARM: dts: vf610-zii-dev-rev-b: Add missing newline
ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
ARM: dts: imx31: fix AVIC base address
ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
arm64: dts: vexpress: Support GICC_DIR operations
ARM: dts: vexpress: Support GICC_DIR operations
firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares
arm64: dts: msm8996: Add required memory carveouts
...
Linus Torvalds [Thu, 5 Jan 2017 18:29:40 +0000 (10:29 -0800)]
Merge tag 'for-linus-4.10-rc2-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- small fixes for xenbus driver
- one fix for xen dom0 boot on huge system
- small cleanups
* tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen: ARM: Zero reserved fields of xatp before making hypervisor call
xen: events: Replace BUG() with BUG_ON()
xen: remove stale xs_input_avail() from header
xen: return xenstore command failures via response instead of rc
xen: xenbus driver must not accept invalid transaction ids
xen/evtchn: use rb_entry()
xen/setup: Don't relocate p2m over existing one
Stephen Hemminger [Thu, 5 Jan 2017 17:36:26 +0000 (09:36 -0800)]
hyper-v: Add myself as additional MAINTAINER
Update the Hyper-V MAINTAINERS to include myself.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Mon, 2 Jan 2017 14:26:17 +0000 (15:26 +0100)]
usb: storage: unusual_uas: Add JMicron JMS56x to unusual device
This device gives the following error on detection.
xhci_hcd 0000:00:11.0: ERROR Transfer event for disabled endpoint or
incorrect stream ring
The same error is not seen when it is added to unusual_device
list with US_FL_NO_REPORT_OPCODES passed.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Oliver Neukum <oneukun@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven [Wed, 14 Dec 2016 14:37:30 +0000 (15:37 +0100)]
usb: hub: Move hub_port_disable() to fix warning if PM is disabled
If CONFIG_PM=n:
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
Fixes:
37be66767e3cae4f ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jérémy Lefaure [Wed, 4 Jan 2017 00:13:52 +0000 (18:13 -0600)]
usb: musb: blackfin: add bfin_fifo_offset in bfin_ops
The function bfin_fifo_offset is defined but not used:
drivers/usb/musb/blackfin.c:36:12: warning: ‘bfin_fifo_offset’ defined
but not used [-Wunused-function]
static u32 bfin_fifo_offset(u8 epnum)
^~~~~~~~~~~~~~~~
Adding bfin_fifo_offset to bfin_ops fixes this warning and allows musb
core to call this function instead of default_fifo_offset.
Fixes:
cc92f6818f6e ("usb: musb: Populate new IO functions for blackfin")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jérémy Lefaure [Wed, 4 Jan 2017 00:13:49 +0000 (18:13 -0600)]
usb: musb: fix compilation warning on unused function
The function musb_run_resume_work is called only when CONFIG_PM is
enabled. So this function should not be defined when CONFIG_PM is
disabled. Otherwise the compiler issues a warning:
drivers/usb/musb/musb_core.c:2057:12: error: ‘musb_run_resume_work’ defined but
not used [-Werror=unused-function]
static int musb_run_resume_work(struct musb *musb)
^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Lindgren [Wed, 4 Jan 2017 00:13:48 +0000 (18:13 -0600)]
usb: musb: Fix trying to free already-free IRQ 4
When unloading omap2430, we can get the following splat:
WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8
Trying to free already-free IRQ 4
...
[<
c01a8b78>] (free_irq) from [<
bf0aea84>]
(musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc])
[<
bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from
[<
bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc])
[<
bf09f88c>] (musb_remove [musb_hdrc]) from [<
c056a384>]
(platform_drv_remove+0x24/0x3c)
...
This is because the irq number in use is 260 nowadays, and the dma
controller is using u8 instead of int.
Fixes:
6995eb68aab7 ("USB: musb: enable low level DMA operation for Blackfin")
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: added Fixes tag]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu [Wed, 4 Jan 2017 00:13:47 +0000 (18:13 -0600)]
usb: musb: dsps: implement clear_ep_rxintr() callback
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu [Wed, 4 Jan 2017 00:13:46 +0000 (18:13 -0600)]
usb: musb: core: add clear_ep_rxintr() to musb_platform_ops
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt.
Clearing ep interrupt is platform dependent, so this patch adds a
platform callback to allow glue driver to clear the ep interrupt.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicholas Piggin [Thu, 5 Jan 2017 10:29:36 +0000 (20:29 +1000)]
kbuild: initramfs cleanup, set target from Kconfig
Rather than keep a list of all possible compression types in the
Makefile, set the target explicitly from Kconfig.
Reviewed-by: Francisco Blas Izquierdo Riera (klondike) <klondike@klondike.es>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicholas Piggin [Thu, 5 Jan 2017 10:29:35 +0000 (20:29 +1000)]
kbuild: initramfs fix dependency checking for compressed target
When using initramfs compression, the data file compression suffix
gets quotes pulled in from Kconfig, e.g., initramfs_data.cpio".gz"
which make does not match a target and causes rebuild.
Fix this by filtering out quotes from the Kconfig string.
Fixes:
35e669e1a254 ("initramfs: select builtin initram compression algorithm on KConfig instead of Makefile")
Reviewed-by: Francisco Blas Izquierdo Riera (klondike) <klondike@klondike.es>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Thu, 5 Jan 2017 16:49:57 +0000 (11:49 -0500)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains accumulated Netfilter fixes for your
net tree:
1) Ensure quota dump and reset happens iff we can deliver numbers to
userspace.
2) Silence splat on incorrect use of smp_processor_id() from nft_queue.
3) Fix an out-of-bound access reported by KASAN in
nf_tables_rule_destroy(), patch from Florian Westphal.
4) Fix layer 4 checksum mangling in the nf_tables payload expression
with IPv6.
5) Fix a race in the CLUSTERIP target from control plane path when two
threads run to add a new configuration object. Serialize invocations
of clusterip_config_init() using spin_lock. From Xin Long.
6) Call br_nf_pre_routing_finish_bridge_finish() once we are done with
the br_nf_pre_routing_finish() hook. From Artur Molchanov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Thu, 5 Jan 2017 16:41:16 +0000 (17:41 +0100)]
Merge tag 'usb-serial-4.10-rc3' of git://git./linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.10-rc3
These fixes address a number of long-standing issues in various
USB-serial drivers which would lead to crashes should a malicious device
lack the expected endpoints.
Included are also a few related fixes, and a couple of unrelated ones
that were found during my survey (e.g. a memleak and a
sleep-while-atomic).
A compiler warning revealed an error-handling issue in the new f81534
driver which is also fixed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Zhu Yanjun [Thu, 5 Jan 2017 07:54:27 +0000 (02:54 -0500)]
r8169: fix the typo in the comment
>From the realtek data sheet, the PID0 should be bit 0.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafael J. Wysocki [Thu, 5 Jan 2017 01:13:31 +0000 (02:13 +0100)]
ACPI / DMAR: Avoid passing NULL to acpi_put_table()
Linus reported that commit
174cc7187e6f "ACPICA: Tables: Back port
acpi_get_table_with_size() and early_acpi_os_unmap_memory() from
Linux kernel" added a new warning on his desktop system:
ACPI Warning: Table
ffffffff9fe6c0a0, Validation count is zero before decrement
which turns out to come from the acpi_put_table() in
detect_intel_iommu().
This happens if the DMAR table is not present in which case NULL is
passed to acpi_put_table() which doesn't check against that and
attempts to handle it regardless.
For this reason, check the pointer passed to acpi_put_table()
before invoking it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Fixes:
6b11d1d67713 ("ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Jan Dakinevich [Thu, 22 Dec 2016 22:13:53 +0000 (01:13 +0300)]
KVM: VMX: remove duplicated declaration
Declaration of VMX_VPID_EXTENT_SUPPORTED_MASK occures twice in the code.
Probably, it was happened after unsuccessful merge.
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
James Hogan [Tue, 3 Jan 2017 17:43:01 +0000 (17:43 +0000)]
KVM: MIPS: Flush KVM entry code from icache globally
Flush the KVM entry code from the icache on all CPUs, not just the one
that built the entry code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.16.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
James Hogan [Tue, 3 Jan 2017 17:43:00 +0000 (17:43 +0000)]
KVM: MIPS: Don't clobber CP0_Status.UX
On 64-bit kernels, MIPS KVM will clear CP0_Status.UX to prevent the
guest (running in user mode) from accessing the 64-bit memory segments.
However the previous value of CP0_Status.UX is never restored when
exiting from the guest.
If the user process uses 64-bit addressing (the n64 ABI) this can result
in address error exceptions from the kernel if it needs to deliver a
signal before returning to user mode, as the kernel will need to write a
sigframe to high user addresses on the user stack which are disallowed
by CP0_Status.UX=0.
This is fixed by explicitly setting SX and UX again when exiting from
the guest, and explicitly clearing those bits when returning to the
guest. Having the SX and UX bits set when handling guest exits (rather
than only when exiting to userland) will be helpful when we support VZ,
since we shouldn't need to directly read or write guest memory, so it
will be valid for cache management IPIs to access host user addresses.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.8.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Michal Marek [Tue, 3 Jan 2017 12:49:42 +0000 (13:49 +0100)]
asm-prototypes: Clear any CPP defines before declaring the functions
The asm-prototypes.h file is used to provide dummy function declarations
for genksyms, when processing asm files with EXPORT_SYMBOL. Make sure
that any architecture defines get out of our way. x86 currently has an
issue with memcpy on 64bit with CONFIG_KMEMCHECK=y and with
memset/__memset on 32bit:
$ cat init/test.c
#include <asm/asm-prototypes.h>
$ make -s init/test.o
In file included from ./arch/x86/include/asm/string.h:4:0,
from ./include/linux/string.h:18,
from ./include/linux/bitmap.h:8,
from ./include/linux/cpumask.h:11,
from ./arch/x86/include/asm/cpumask.h:4,
from ./arch/x86/include/asm/msr.h:10,
from ./arch/x86/include/asm/processor.h:20,
from ./arch/x86/include/asm/cpufeature.h:4,
from ./arch/x86/include/asm/thread_info.h:52,
from ./include/linux/thread_info.h:25,
from ./arch/x86/include/asm/preempt.h:6,
from ./include/linux/preempt.h:59,
from ./include/linux/spinlock.h:50,
from ./include/linux/seqlock.h:35,
from ./include/linux/time.h:5,
from ./include/uapi/linux/timex.h:56,
from ./include/linux/timex.h:56,
from ./include/linux/sched.h:19,
from ./include/linux/uaccess.h:4,
from ./arch/x86/include/asm/asm-prototypes.h:2,
from init/test.c:1:
./arch/x86/include/asm/string_64.h:52:47: error: expected declaration specifiers or ‘...’ before ‘(’ token
#define memcpy(dst, src, len) __inline_memcpy((dst), (src), (len))
./include/asm-generic/asm-prototypes.h:6:14: note: in expansion of macro ‘memcpy’
extern void *memcpy(void *, const void *, __kernel_size_t);
^
...
During real build, this manifests itself by genksyms segfaulting.
Fixes:
334bb7738764 ("x86/kbuild: enable modversions for symbols exported from asm")
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Cc: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Michal Marek <mmarek@suse.com>
Johannes Berg [Thu, 5 Jan 2017 09:57:14 +0000 (10:57 +0100)]
nl80211: fix sched scan netlink socket owner destruction
A single netlink socket might own multiple interfaces *and* a
scheduled scan request (which might belong to another interface),
so when it goes away both may need to be destroyed.
Remove the schedule_scan_stop indirection to fix this - it's only
needed for interface destruction because of the way this works
right now, with a single work taking care of all interfaces.
Cc: stable@vger.kernel.org
Fixes:
93a1e86ce10e4 ("nl80211: Stop scheduled scan if netlink client disappears")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Takashi Sakamoto [Thu, 5 Jan 2017 00:41:31 +0000 (09:41 +0900)]
Revert "ALSA: firewire-lib: change structure member with proper type"
This reverts commit
6b7e95d1336b9eb0d4c6db190ce756480496bd13. This commit
is based on a concern about value of the given parameter. It's expected
to be ORed value with some enumeration-constants, thus often it can not be
one of the enumeration-constants. I understood that this is out of
specification and causes implementation-dependent issues.
In C language specification, enumerated type can be interpreted as an
integer type, in which all of enumeration-constants in corresponding
enumerator-list can be stored. Implementations can select one of char,
signed int and unsigned int as its type, and this selection is
implementation-dependent.
In GCC, a signed integer is selected when at least one of
enumeration-constants has negative value, else an unsigned integer is
selected. This behaviour can be switched by -fshort-enums to short type.
Anyway, the type can be decided after scanning all of
enumeration-constants.
Totally, there's no rules to constrain the value of enumerated type to
be one of enumeration-constants. In short, in enumerated type, decision
of actual type for the type is the most important and
enumeration-constants are just used for the decision, thus it's permitted
to have an integer value in a range of enumeration-constants. In our case,
actual type for the type is currently deterministic to be either char or
unsigned int. Under GCC, it's unsigned int.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ioan-Adrian Ratiu [Wed, 4 Jan 2017 22:37:47 +0000 (00:37 +0200)]
ALSA: usb-audio: test EP_FLAG_RUNNING at urb completion
Testing EP_FLAG_RUNNING in snd_complete_urb() before running the completion
logic allows us to save a few cpu cycles by returning early, skipping the
pending urb in case the stream was stopped; the stop logic handles the urb
and sets the completion callbacks to NULL.
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ioan-Adrian Ratiu [Wed, 4 Jan 2017 22:37:46 +0000 (00:37 +0200)]
ALSA: usb-audio: Fix irq/process data synchronization
Commit
16200948d83 ("ALSA: usb-audio: Fix race at stopping the stream") was
incomplete causing another more severe kernel panic, so it got reverted.
This fixes both the original problem and its fallout kernel race/crash.
The original fix is to move the endpoint member NULL clearing logic inside
wait_clear_urbs() so the irq triggering the urb completion doesn't call
retire_capture/playback_urb() after the NULL clearing and generate a panic.
However this creates a new race between snd_usb_endpoint_start()'s call
to wait_clear_urbs() and the irq urb completion handler which again calls
retire_capture/playback_urb() leading to a new NULL dereference.
We keep the EP deactivation code in snd_usb_endpoint_start() because
removing it will break the EP reference counting (see [1] [2] for info),
however we don't need the "can_sleep" mechanism anymore because a new
function was introduced (snd_usb_endpoint_sync_pending_stop()) which
synchronizes pending stops and gets called inside the pcm prepare callback.
It also makes sense to remove can_sleep because it was also removed from
deactivate_urbs() signature in [3] so we benefit from more simplification.
[1] commit
015618b90 ("ALSA: snd-usb: Fix URB cancellation at stream start")
[2] commit
e9ba389c5 ("ALSA: usb-audio: Fix scheduling-while-atomic bug in PCM capture stream")
[3] commit
ccc1696d5 ("ALSA: usb-audio: simplify endpoint deactivation code")
Fixes:
f8114f8583bb ("Revert "ALSA: usb-audio: Fix race at stopping the stream"")
Signed-off-by: Ioan-Adrian Ratiu <adi@adirat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Thu, 5 Jan 2017 02:33:35 +0000 (18:33 -0800)]
Merge tag 'xfs-for-linus-4.10-rc3' of git://git./fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- fixes for crashes and double-cleanup errors
- XFS maintainership handover
- fix to prevent absurdly large block reservations
- fix broken sysfs getter/setters
* tag 'xfs-for-linus-4.10-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix max_retries _show and _store functions
xfs: update MAINTAINERS
xfs: fix crash and data corruption due to removal of busy COW extents
xfs: use the actual AG length when reserving blocks
xfs: fix double-cleanup when CUI recovery fails
Hoan Tran [Thu, 15 Dec 2016 22:55:00 +0000 (14:55 -0800)]
cpufreq: dt: Add support for APM X-Gene 2
Add the compatible string for supporting the generic device tree cpufreq-dt
driver on APM's X-Gene 2 SoC.
Signed-off-by: Hoan Tran <hotran@apm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>