OSDN Git Service
Jakub Kicinski [Mon, 31 Jan 2022 21:17:30 +0000 (13:17 -0800)]
ethernet: smc911x: fix indentation in get/set EEPROM
Build bot produced a smatch indentation warning,
the code looks correct but it mixes spaces and tabs.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220131211730.3940875-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonathan McDowell [Mon, 31 Jan 2022 13:56:41 +0000 (13:56 +0000)]
net: phy: Fix qca8081 with speeds lower than 2.5Gb/s
A typo in qca808x_read_status means we try to set SMII mode on the port
rather than SGMII when the link speed is not 2.5Gb/s. This results in no
traffic due to the mismatch in configuration between the phy and the
mac.
v2:
Only change interface mode when the link is up
Fixes:
79c7bc0521545 ("net: phy: add qca8081 read_status")
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lior Nahmanson [Sun, 30 Jan 2022 11:29:01 +0000 (13:29 +0200)]
net: macsec: Fix offload support for NETDEV_UNREGISTER event
Current macsec netdev notify handler handles NETDEV_UNREGISTER event by
releasing relevant SW resources only, this causes resources leak in case
of macsec HW offload, as the underlay driver was not notified to clean
it's macsec offload resources.
Fix by calling the underlay driver to clean it's relevant resources
by moving offload handling from macsec_dellink() to macsec_common_dellink()
when handling NETDEV_UNREGISTER event.
Fixes:
3cf3227a21d1 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/1643542141-28956-1-git-send-email-raeds@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Camel Guo [Mon, 31 Jan 2022 08:38:40 +0000 (09:38 +0100)]
net: stmmac: dump gmac4 DMA registers correctly
Unlike gmac100, gmac1000, gmac4 has 27 DMA registers and they are
located at DMA_CHAN_BASE_ADDR (0x1100). In order for ethtool to dump
gmac4 DMA registers correctly, this commit checks if a net_device has
gmac4 and uses different logic to dump its DMA registers.
This fixes the following KASAN warning, which can normally be triggered
by a command similar like "ethtool -d eth0":
BUG: KASAN: vmalloc-out-of-bounds in dwmac4_dump_dma_regs+0x6d4/0xb30
Write of size 4 at addr
ffffffc010177100 by task ethtool/1839
kasan_report+0x200/0x21c
__asan_report_store4_noabort+0x34/0x60
dwmac4_dump_dma_regs+0x6d4/0xb30
stmmac_ethtool_gregs+0x110/0x204
ethtool_get_regs+0x200/0x4b0
dev_ethtool+0x1dac/0x3800
dev_ioctl+0x7c0/0xb50
sock_ioctl+0x298/0x6c4
...
Fixes:
fbf68229ffe7 ("net: stmmac: unify registers dumps methods")
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20220131083841.3346801-1-camel.guo@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arınç ÜNAL [Sat, 29 Jan 2022 06:27:04 +0000 (09:27 +0300)]
net: dsa: mt7530: make NET_DSA_MT7530 select MEDIATEK_GE_PHY
Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.
A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.
Fixes:
b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220129062703.595-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wen Gu [Wed, 26 Jan 2022 15:33:04 +0000 (23:33 +0800)]
net/smc: Forward wakeup to smc socket waitqueue after fallback
When we replace TCP with SMC and a fallback occurs, there may be
some socket waitqueue entries remaining in smc socket->wq, such
as eppoll_entries inserted by userspace applications.
After the fallback, data flows over TCP/IP and only clcsocket->wq
will be woken up. Applications can't be notified by the entries
which were inserted in smc socket->wq before fallback. So we need
a mechanism to wake up smc socket->wq at the same time if some
entries remaining in it.
The current workaround is to transfer the entries from smc socket->wq
to clcsock->wq during the fallback. But this may cause a crash
like this:
general protection fault, probably for non-canonical address 0xdead000000000100: 0000 [#1] PREEMPT SMP PTI
CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Tainted: G E 5.16.0+ #107
RIP: 0010:__wake_up_common+0x65/0x170
Call Trace:
<IRQ>
__wake_up_common_lock+0x7a/0xc0
sock_def_readable+0x3c/0x70
tcp_data_queue+0x4a7/0xc40
tcp_rcv_established+0x32f/0x660
? sk_filter_trim_cap+0xcb/0x2e0
tcp_v4_do_rcv+0x10b/0x260
tcp_v4_rcv+0xd2a/0xde0
ip_protocol_deliver_rcu+0x3b/0x1d0
ip_local_deliver_finish+0x54/0x60
ip_local_deliver+0x6a/0x110
? tcp_v4_early_demux+0xa2/0x140
? tcp_v4_early_demux+0x10d/0x140
ip_sublist_rcv_finish+0x49/0x60
ip_sublist_rcv+0x19d/0x230
ip_list_rcv+0x13e/0x170
__netif_receive_skb_list_core+0x1c2/0x240
netif_receive_skb_list_internal+0x1e6/0x320
napi_complete_done+0x11d/0x190
mlx5e_napi_poll+0x163/0x6b0 [mlx5_core]
__napi_poll+0x3c/0x1b0
net_rx_action+0x27c/0x300
__do_softirq+0x114/0x2d2
irq_exit_rcu+0xb4/0xe0
common_interrupt+0xba/0xe0
</IRQ>
<TASK>
The crash is caused by privately transferring waitqueue entries from
smc socket->wq to clcsock->wq. The owners of these entries, such as
epoll, have no idea that the entries have been transferred to a
different socket wait queue and still use original waitqueue spinlock
(smc socket->wq.wait.lock) to make the entries operation exclusive,
but it doesn't work. The operations to the entries, such as removing
from the waitqueue (now is clcsock->wq after fallback), may cause a
crash when clcsock waitqueue is being iterated over at the moment.
This patch tries to fix this by no longer transferring wait queue
entries privately, but introducing own implementations of clcsock's
callback functions in fallback situation. The callback functions will
forward the wakeup to smc socket->wq if clcsock->wq is actually woken
up and smc socket->wq has remaining entries.
Fixes:
2153bd1e3d3d ("net/smc: Transfer remaining wait queue entries during fallback")
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Fri, 28 Jan 2022 14:15:50 +0000 (22:15 +0800)]
net: stmmac: properly handle with runtime pm in stmmac_dvr_remove()
There are two issues with runtime pm handling in stmmac_dvr_remove():
1. the mac is runtime suspended before stopping dma and rx/tx. We
need to ensure the device is properly resumed back.
2. the stmmaceth clk enable/disable isn't balanced in both exit and
error handling code path. Take the exit code path for example, when we
unbind the driver or rmmod the driver module, the mac is runtime
suspended as said above, so the stmmaceth clk is disabled, but
stmmac_dvr_remove()
stmmac_remove_config_dt()
clk_disable_unprepare()
CCF will complain this time. The error handling code path suffers
from the similar situtaion.
Here are kernel warnings in error handling code path on Allwinner D1
platform:
[ 1.604695] ------------[ cut here ]------------
[ 1.609328] bus-emac already disabled
[ 1.613015] WARNING: CPU: 0 PID: 38 at drivers/clk/clk.c:952 clk_core_disable+0xcc/0xec
[ 1.621039] CPU: 0 PID: 38 Comm: kworker/u2:1 Not tainted 5.14.0-rc4#1
[ 1.627653] Hardware name: Allwinner D1 NeZha (DT)
[ 1.632443] Workqueue: events_unbound deferred_probe_work_func
[ 1.638286] epc : clk_core_disable+0xcc/0xec
[ 1.642561] ra : clk_core_disable+0xcc/0xec
[ 1.646835] epc :
ffffffff8023c2ec ra :
ffffffff8023c2ec sp :
ffffffd00411bb10
[ 1.654054] gp :
ffffffff80ec9988 tp :
ffffffe00143a800 t0 :
ffffffff80ed6a6f
[ 1.661272] t1 :
ffffffff80ed6a60 t2 :
0000000000000000 s0 :
ffffffe001509e00
[ 1.668489] s1 :
0000000000000001 a0 :
0000000000000019 a1 :
ffffffff80e80bd8
[ 1.675707] a2 :
00000000ffffefff a3 :
00000000000000f4 a4 :
0000000000000002
[ 1.682924] a5 :
0000000000000001 a6 :
0000000000000030 a7 :
00000000028f5c29
[ 1.690141] s2 :
0000000000000800 s3 :
ffffffe001375000 s4 :
ffffffe01fdf7a80
[ 1.697358] s5 :
ffffffe001375010 s6 :
ffffffff8001fc10 s7 :
ffffffffffffffff
[ 1.704577] s8 :
0000000000000001 s9 :
ffffffff80ecb248 s10:
ffffffe001b80000
[ 1.711794] s11:
ffffffe001b80760 t3 :
0000000000000062 t4 :
ffffffffffffffff
[ 1.719012] t5 :
ffffffff80e0f6d8 t6 :
ffffffd00411b8f0
[ 1.724321] status:
8000000201800100 badaddr:
0000000000000000 cause:
0000000000000003
[ 1.732233] [<
ffffffff8023c2ec>] clk_core_disable+0xcc/0xec
[ 1.737810] [<
ffffffff80240430>] clk_disable+0x38/0x78
[ 1.742956] [<
ffffffff8001fc0c>] worker_thread+0x1a8/0x4d8
[ 1.748451] [<
ffffffff8031a500>] stmmac_remove_config_dt+0x1c/0x4c
[ 1.754646] [<
ffffffff8031c8ec>] sun8i_dwmac_probe+0x378/0x82c
[ 1.760484] [<
ffffffff8001fc0c>] worker_thread+0x1a8/0x4d8
[ 1.765975] [<
ffffffff8029a6c8>] platform_probe+0x64/0xf0
[ 1.771382] [<
ffffffff8029833c>] really_probe.part.0+0x8c/0x30c
[ 1.777305] [<
ffffffff8029865c>] __driver_probe_device+0xa0/0x148
[ 1.783402] [<
ffffffff8029873c>] driver_probe_device+0x38/0x138
[ 1.789324] [<
ffffffff802989cc>] __device_attach_driver+0xd0/0x170
[ 1.795508] [<
ffffffff802988f8>] __driver_attach_async_helper+0xbc/0xc0
[ 1.802125] [<
ffffffff802965ac>] bus_for_each_drv+0x68/0xb4
[ 1.807701] [<
ffffffff80298d1c>] __device_attach+0xd8/0x184
[ 1.813277] [<
ffffffff802967b0>] bus_probe_device+0x98/0xbc
[ 1.818852] [<
ffffffff80297904>] deferred_probe_work_func+0x90/0xd4
[ 1.825122] [<
ffffffff8001f8b8>] process_one_work+0x1e4/0x390
[ 1.830872] [<
ffffffff8001fd80>] worker_thread+0x31c/0x4d8
[ 1.836362] [<
ffffffff80026bf4>] kthreadd+0x94/0x188
[ 1.841335] [<
ffffffff80026bf4>] kthreadd+0x94/0x188
[ 1.846304] [<
ffffffff8001fa60>] process_one_work+0x38c/0x390
[ 1.852054] [<
ffffffff80026564>] kthread+0x124/0x160
[ 1.857021] [<
ffffffff8002643c>] set_kthread_struct+0x5c/0x60
[ 1.862770] [<
ffffffff80001f08>] ret_from_syscall_rejected+0x8/0xc
[ 1.868956] ---[ end trace
8d5c6046255f84a0 ]---
[ 1.873675] ------------[ cut here ]------------
[ 1.878366] bus-emac already unprepared
[ 1.882378] WARNING: CPU: 0 PID: 38 at drivers/clk/clk.c:810 clk_core_unprepare+0xe4/0x168
[ 1.890673] CPU: 0 PID: 38 Comm: kworker/u2:1 Tainted: G W 5.14.0-rc4 #1
[ 1.898674] Hardware name: Allwinner D1 NeZha (DT)
[ 1.903464] Workqueue: events_unbound deferred_probe_work_func
[ 1.909305] epc : clk_core_unprepare+0xe4/0x168
[ 1.913840] ra : clk_core_unprepare+0xe4/0x168
[ 1.918375] epc :
ffffffff8023d6cc ra :
ffffffff8023d6cc sp :
ffffffd00411bb10
[ 1.925593] gp :
ffffffff80ec9988 tp :
ffffffe00143a800 t0 :
0000000000000002
[ 1.932811] t1 :
ffffffe01f743be0 t2 :
0000000000000040 s0 :
ffffffe001509e00
[ 1.940029] s1 :
0000000000000001 a0 :
000000000000001b a1 :
ffffffe00143a800
[ 1.947246] a2 :
0000000000000000 a3 :
00000000000000f4 a4 :
0000000000000001
[ 1.954463] a5 :
0000000000000000 a6 :
0000000005fce2a5 a7 :
0000000000000001
[ 1.961680] s2 :
0000000000000800 s3 :
ffffffff80afeb90 s4 :
ffffffe01fdf7a80
[ 1.968898] s5 :
ffffffe001375010 s6 :
ffffffff8001fc10 s7 :
ffffffffffffffff
[ 1.976115] s8 :
0000000000000001 s9 :
ffffffff80ecb248 s10:
ffffffe001b80000
[ 1.983333] s11:
ffffffe001b80760 t3 :
ffffffff80b39120 t4 :
0000000000000001
[ 1.990550] t5 :
0000000000000000 t6 :
ffffffe001600002
[ 1.995859] status:
8000000201800120 badaddr:
0000000000000000 cause:
0000000000000003
[ 2.003771] [<
ffffffff8023d6cc>] clk_core_unprepare+0xe4/0x168
[ 2.009609] [<
ffffffff802403a0>] clk_unprepare+0x24/0x3c
[ 2.014929] [<
ffffffff8031a508>] stmmac_remove_config_dt+0x24/0x4c
[ 2.021125] [<
ffffffff8031c8ec>] sun8i_dwmac_probe+0x378/0x82c
[ 2.026965] [<
ffffffff8001fc0c>] worker_thread+0x1a8/0x4d8
[ 2.032463] [<
ffffffff8029a6c8>] platform_probe+0x64/0xf0
[ 2.037871] [<
ffffffff8029833c>] really_probe.part.0+0x8c/0x30c
[ 2.043795] [<
ffffffff8029865c>] __driver_probe_device+0xa0/0x148
[ 2.049892] [<
ffffffff8029873c>] driver_probe_device+0x38/0x138
[ 2.055815] [<
ffffffff802989cc>] __device_attach_driver+0xd0/0x170
[ 2.061999] [<
ffffffff802988f8>] __driver_attach_async_helper+0xbc/0xc0
[ 2.068616] [<
ffffffff802965ac>] bus_for_each_drv+0x68/0xb4
[ 2.074193] [<
ffffffff80298d1c>] __device_attach+0xd8/0x184
[ 2.079769] [<
ffffffff802967b0>] bus_probe_device+0x98/0xbc
[ 2.085345] [<
ffffffff80297904>] deferred_probe_work_func+0x90/0xd4
[ 2.091616] [<
ffffffff8001f8b8>] process_one_work+0x1e4/0x390
[ 2.097367] [<
ffffffff8001fd80>] worker_thread+0x31c/0x4d8
[ 2.102858] [<
ffffffff80026bf4>] kthreadd+0x94/0x188
[ 2.107830] [<
ffffffff80026bf4>] kthreadd+0x94/0x188
[ 2.112800] [<
ffffffff8001fa60>] process_one_work+0x38c/0x390
[ 2.118551] [<
ffffffff80026564>] kthread+0x124/0x160
[ 2.123520] [<
ffffffff8002643c>] set_kthread_struct+0x5c/0x60
[ 2.129268] [<
ffffffff80001f08>] ret_from_syscall_rejected+0x8/0xc
[ 2.135455] ---[ end trace
8d5c6046255f84a1 ]---
Fixes:
5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 28 Jan 2022 15:10:45 +0000 (15:10 +0000)]
Merge tag 'ieee802154-for-net-2022-01-28' of git://git./linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2022-01-28
An update from ieee802154 for your *net* tree.
A bunch of fixes in drivers, all from Miquel Raynal.
Clarifying the default channel in hwsim, leak fixes in at86rf230 and ca8210 as
well as a symbol duration fix for mcr20a. Topping up the driver fixes with
better error codes in nl802154 and a cleanup in MAINTAINERS for an orphaned
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyue Wang [Fri, 28 Jan 2022 10:47:14 +0000 (18:47 +0800)]
gve: fix the wrong AdminQ buffer queue index check
The 'tail' and 'head' are 'unsigned int' type free-running count, when
'head' is overflow, the 'int i (= tail) < u32 head' will be false:
Only '- loop 0: idx = 63' result is shown, so it needs to use 'int' type
to compare, it can handle the overflow correctly.
typedef uint32_t u32;
int main()
{
u32 tail, head;
int stail, shead;
int i, loop;
tail = 0xffffffff;
head = 0x00000000;
for (i = tail, loop = 0; i < head; i++) {
unsigned int idx = i & 63;
printf("+ loop %d: idx = %u\n", loop++, idx);
}
stail = tail;
shead = head;
for (i = stail, loop = 0; i < shead; i++) {
unsigned int idx = i & 63;
printf("- loop %d: idx = %u\n", loop++, idx);
}
return 0;
}
Fixes:
5cdad90de62c ("gve: Batch AQ commands for creating and destroying queues.")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 28 Jan 2022 14:56:47 +0000 (14:56 +0000)]
Merge branch 'ax25-fixes'
Duoming Zhou says:
====================
ax25: fix NPD and UAF bugs when detaching ax25 device
There are NPD and UAF bugs when detaching ax25 device, we
use lock and refcount to mitigate these bugs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Duoming Zhou [Fri, 28 Jan 2022 04:47:16 +0000 (12:47 +0800)]
ax25: add refcount in ax25_dev to avoid UAF bugs
If we dereference ax25_dev after we call kfree(ax25_dev) in
ax25_dev_device_down(), it will lead to concurrency UAF bugs.
There are eight syscall functions suffer from UAF bugs, include
ax25_bind(), ax25_release(), ax25_connect(), ax25_ioctl(),
ax25_getname(), ax25_sendmsg(), ax25_getsockopt() and
ax25_info_show().
One of the concurrency UAF can be shown as below:
(USE) | (FREE)
| ax25_device_event
| ax25_dev_device_down
ax25_bind | ...
... | kfree(ax25_dev)
ax25_fillin_cb() | ...
ax25_fillin_cb_from_dev() |
... |
The root cause of UAF bugs is that kfree(ax25_dev) in
ax25_dev_device_down() is not protected by any locks.
When ax25_dev, which there are still pointers point to,
is released, the concurrency UAF bug will happen.
This patch introduces refcount into ax25_dev in order to
guarantee that there are no pointers point to it when ax25_dev
is released.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duoming Zhou [Fri, 28 Jan 2022 04:47:15 +0000 (12:47 +0800)]
ax25: improve the incomplete fix to avoid UAF and NPD bugs
The previous commit
1ade48d0c27d ("ax25: NPD bug when detaching
AX25 device") introduce lock_sock() into ax25_kill_by_device to
prevent NPD bug. But the concurrency NPD or UAF bug will occur,
when lock_sock() or release_sock() dereferences the ax25_cb->sock.
The NULL pointer dereference bug can be shown as below:
ax25_kill_by_device() | ax25_release()
| ax25_destroy_socket()
| ax25_cb_del()
... | ...
| ax25->sk=NULL;
lock_sock(s->sk); //(1) |
s->ax25_dev = NULL; | ...
release_sock(s->sk); //(2) |
... |
The root cause is that the sock is set to null before dereference
site (1) or (2). Therefore, this patch extracts the ax25_cb->sock
in advance, and uses ax25_list_lock to protect it, which can synchronize
with ax25_cb_del() and ensure the value of sock is not null before
dereference sites.
The concurrency UAF bug can be shown as below:
ax25_kill_by_device() | ax25_release()
| ax25_destroy_socket()
... | ...
| sock_put(sk); //FREE
lock_sock(s->sk); //(1) |
s->ax25_dev = NULL; | ...
release_sock(s->sk); //(2) |
... |
The root cause is that the sock is released before dereference
site (1) or (2). Therefore, this patch uses sock_hold() to increase
the refcount of sock and uses ax25_list_lock to protect it, which
can synchronize with ax25_cb_del() in ax25_destroy_socket() and
ensure the sock wil not be released before dereference sites.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuji Ishikawa [Thu, 27 Jan 2022 12:17:14 +0000 (21:17 +0900)]
net: stmmac: dwmac-visconti: No change to ETHER_CLOCK_SEL for unexpected speed request.
Variable clk_sel_val is not initialized in the default case of the first switch statement.
In that case, the function should return immediately without any changes to the hardware.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes:
b38dd98ff8d0 ("net: stmmac: Add Toshiba Visconti SoCs glue driver")
Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raju Rangoju [Thu, 27 Jan 2022 06:02:22 +0000 (11:32 +0530)]
net: amd-xgbe: ensure to reset the tx_timer_active flag
Ensure to reset the tx_timer_active flag in xgbe_stop(),
otherwise a port restart may result in tx timeout due to
uncleared flag.
Fixes:
c635eaacbf77 ("amd-xgbe: Remove Tx coalescing")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20220127060222.453371-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 28 Jan 2022 02:53:01 +0000 (18:53 -0800)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Remove leftovers from flowtable modules, from Geert Uytterhoeven.
2) Missing refcount increment of conntrack template in nft_ct,
from Florian Westphal.
3) Reduce nft_zone selftest time, also from Florian.
4) Add selftest to cover stateless NAT on fragments, from Florian Westphal.
5) Do not set net_device when for reject packets from the bridge path,
from Phil Sutter.
6) Cancel register tracking info on nft_byteorder operations.
7) Extend nft_concat_range selftest to cover set reload with no elements,
from Florian Westphal.
8) Remove useless update of pointer in chain blob builder, reported
by kbuild test robot.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nf_tables: remove assignment with no effect in chain blob builder
selftests: nft_concat_range: add test for reload with no element add/del
netfilter: nft_byteorder: track register operations
netfilter: nft_reject_bridge: Fix for missing reply from prerouting
selftests: netfilter: check stateless nat udp checksum fixup
selftests: netfilter: reduce zone stress test running time
netfilter: nft_ct: fix use after free when attaching zone template
netfilter: Remove flowtable relics
====================
Link: https://lore.kernel.org/r/20220127235235.656931-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Shyam Sundar S K [Thu, 27 Jan 2022 09:20:03 +0000 (14:50 +0530)]
net: amd-xgbe: Fix skb data length underflow
There will be BUG_ON() triggered in include/linux/skbuff.h leading to
intermittent kernel panic, when the skb length underflow is detected.
Fix this by dropping the packet if such length underflows are seen
because of inconsistencies in the hardware descriptors.
Fixes:
622c36f143fc ("amd-xgbe: Fix jumbo MTU processing on newer hardware")
Suggested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20220127092003.2812745-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 27 Jan 2022 18:58:39 +0000 (20:58 +0200)]
Merge tag 'net-5.17-rc2' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter and can.
Current release - new code bugs:
- tcp: add a missing sk_defer_free_flush() in tcp_splice_read()
- tcp: add a stub for sk_defer_free_flush(), fix CONFIG_INET=n
- nf_tables: set last expression in register tracking area
- nft_connlimit: fix memleak if nf_ct_netns_get() fails
- mptcp: fix removing ids bitmap setting
- bonding: use rcu_dereference_rtnl when getting active slave
- fix three cases of sleep in atomic context in drivers: lan966x, gve
- handful of build fixes for esoteric drivers after netdev->dev_addr
was made const
Previous releases - regressions:
- revert "ipv6: Honor all IPv6 PIO Valid Lifetime values", it broke
Linux compatibility with USGv6 tests
- procfs: show net device bound packet types
- ipv4: fix ip option filtering for locally generated fragments
- phy: broadcom: hook up soft_reset for BCM54616S
Previous releases - always broken:
- ipv4: raw: lock the socket in raw_bind()
- ipv4: decrease the use of shared IPID generator to decrease the
chance of attackers guessing the values
- procfs: fix cross-netns information leakage in /proc/net/ptype
- ethtool: fix link extended state for big endian
- bridge: vlan: fix single net device option dumping
- ping: fix the sk_bound_dev_if match in ping_lookup"
* tag 'net-5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
net: bridge: vlan: fix memory leak in __allowed_ingress
net: socket: rename SKB_DROP_REASON_SOCKET_FILTER
ipv4: remove sparse error in ip_neigh_gw4()
ipv4: avoid using shared IP generator for connected sockets
ipv4: tcp: send zero IPID in SYNACK messages
ipv4: raw: lock the socket in raw_bind()
MAINTAINERS: add missing IPv4/IPv6 header paths
MAINTAINERS: add more files to eth PHY
net: stmmac: dwmac-sun8i: use return val of readl_poll_timeout()
net: bridge: vlan: fix single net device option dumping
net: stmmac: skip only stmmac_ptp_register when resume from suspend
net: stmmac: configure PTP clock source prior to PTP initialization
Revert "ipv6: Honor all IPv6 PIO Valid Lifetime values"
connector/cn_proc: Use task_is_in_init_pid_ns()
pid: Introduce helper task_is_in_init_pid_ns()
gve: Fix GFP flags when allocing pages
net: lan966x: Fix sleep in atomic context when updating MAC table
net: lan966x: Fix sleep in atomic context when injecting frames
ethernet: seeq/ether3: don't write directly to netdev->dev_addr
ethernet: 8390/etherh: don't write directly to netdev->dev_addr
...
Tim Yi [Thu, 27 Jan 2022 07:49:53 +0000 (15:49 +0800)]
net: bridge: vlan: fix memory leak in __allowed_ingress
When using per-vlan state, if vlan snooping and stats are disabled,
untagged or priority-tagged ingress frame will go to check pvid state.
If the port state is forwarding and the pvid state is not
learning/forwarding, untagged or priority-tagged frame will be dropped
but skb memory is not freed.
Should free skb when __allowed_ingress returns false.
Fixes:
a580c76d534c ("net: bridge: vlan: add per-vlan state")
Signed-off-by: Tim Yi <tim.yi@pica8.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20220127074953.12632-1-tim.yi@pica8.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso [Thu, 27 Jan 2022 12:40:38 +0000 (13:40 +0100)]
netfilter: nf_tables: remove assignment with no effect in chain blob builder
cppcheck possible warnings:
>> net/netfilter/nf_tables_api.c:2014:2: warning: Assignment of function parameter has no effect outside the function. Did you forget dereferencing it? [uselessAssignmentPtrArg]
ptr += offsetof(struct nft_rule_dp, data);
^
Reported-by: kernel test robot <yujie.liu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Menglong Dong [Thu, 27 Jan 2022 09:13:01 +0000 (17:13 +0800)]
net: socket: rename SKB_DROP_REASON_SOCKET_FILTER
Rename SKB_DROP_REASON_SOCKET_FILTER, which is used
as the reason of skb drop out of socket filter before
it's part of a released kernel. It will be used for
more protocols than just TCP in future series.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/all/20220127091308.91401-2-imagedong@tencent.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Thu, 27 Jan 2022 01:34:04 +0000 (17:34 -0800)]
ipv4: remove sparse error in ip_neigh_gw4()
./include/net/route.h:373:48: warning: incorrect type in argument 2 (different base types)
./include/net/route.h:373:48: expected unsigned int [usertype] key
./include/net/route.h:373:48: got restricted __be32 [usertype] daddr
Fixes:
5c9f7c1dfc2e ("ipv4: Add helpers for neigh lookup for nexthop")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220127013404.1279313-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 27 Jan 2022 16:37:05 +0000 (08:37 -0800)]
Merge branch 'ipv4-less-uses-of-shared-ip-generator'
Eric Dumazet says:
====================
ipv4: less uses of shared IP generator
From: Eric Dumazet <edumazet@google.com>
We keep receiving research reports based on linux IPID generation.
Before breaking part of the Internet by switching to pure
random generator, this series reduces the need for the
shared IP generator for TCP sockets.
====================
Link: https://lore.kernel.org/r/20220127011022.1274803-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Thu, 27 Jan 2022 01:10:22 +0000 (17:10 -0800)]
ipv4: avoid using shared IP generator for connected sockets
ip_select_ident_segs() has been very conservative about using
the connected socket private generator only for packets with IP_DF
set, claiming it was needed for some VJ compression implementations.
As mentioned in this referenced document, this can be abused.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
Before switching to pure random IPID generation and possibly hurt
some workloads, lets use the private inet socket generator.
Not only this will remove one vulnerability, this will also
improve performance of TCP flows using pmtudisc==IP_PMTUDISC_DONT
Fixes:
73f156a6e8c1 ("inetpeer: get rid of ip_id_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reported-by: Ray Che <xijiache@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Thu, 27 Jan 2022 01:10:21 +0000 (17:10 -0800)]
ipv4: tcp: send zero IPID in SYNACK messages
In commit
431280eebed9 ("ipv4: tcp: send zero IPID for RST and
ACK sent in SYN-RECV and TIME-WAIT state") we took care of some
ctl packets sent by TCP.
It turns out we need to use a similar strategy for SYNACK packets.
By default, they carry IP_DF and IPID==0, but there are ways
to ask them to use the hashed IP ident generator and thus
be used to build off-path attacks.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
One of this way is to force (before listener is started)
echo 1 >/proc/sys/net/ipv4/ip_no_pmtu_disc
Another way is using forged ICMP ICMP_FRAG_NEEDED
with a very small MTU (like 68) to force a false return from
ip_dont_fragment()
In this patch, ip_build_and_send_pkt() uses the following
heuristics.
1) Most SYNACK packets are smaller than IPV4_MIN_MTU and therefore
can use IP_DF regardless of the listener or route pmtu setting.
2) In case the SYNACK packet is bigger than IPV4_MIN_MTU,
we use prandom_u32() generator instead of the IPv4 hashed ident one.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ray Che <xijiache@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Cc: Geoff Alexander <alexandg@cs.unm.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mathias Krause [Thu, 27 Jan 2022 08:34:19 +0000 (18:34 +1000)]
drm/vmwgfx: Fix stale file descriptors on failed usercopy
A failing usercopy of the fence_rep object will lead to a stale entry in
the file descriptor table as put_unused_fd() won't release it. This
enables userland to refer to a dangling 'file' object through that still
valid file descriptor, leading to all kinds of use-after-free
exploitation scenarios.
Fix this by deferring the call to fd_install() until after the usercopy
has succeeded.
Fixes:
c906965dee22 ("drm/vmwgfx: Add export fence to file descriptor support")
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Thu, 27 Jan 2022 00:51:16 +0000 (16:51 -0800)]
ipv4: raw: lock the socket in raw_bind()
For some reason, raw_bind() forgot to lock the socket.
BUG: KCSAN: data-race in __ip4_datagram_connect / raw_bind
write to 0xffff8881170d4308 of 4 bytes by task 5466 on cpu 0:
raw_bind+0x1b0/0x250 net/ipv4/raw.c:739
inet_bind+0x56/0xa0 net/ipv4/af_inet.c:443
__sys_bind+0x14b/0x1b0 net/socket.c:1697
__do_sys_bind net/socket.c:1708 [inline]
__se_sys_bind net/socket.c:1706 [inline]
__x64_sys_bind+0x3d/0x50 net/socket.c:1706
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff8881170d4308 of 4 bytes by task 5468 on cpu 1:
__ip4_datagram_connect+0xb7/0x7b0 net/ipv4/datagram.c:39
ip4_datagram_connect+0x2a/0x40 net/ipv4/datagram.c:89
inet_dgram_connect+0x107/0x190 net/ipv4/af_inet.c:576
__sys_connect_file net/socket.c:1900 [inline]
__sys_connect+0x197/0x1b0 net/socket.c:1917
__do_sys_connect net/socket.c:1927 [inline]
__se_sys_connect net/socket.c:1924 [inline]
__x64_sys_connect+0x3d/0x50 net/socket.c:1924
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000000 -> 0x0003007f
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 5468 Comm: syz-executor.5 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 26 Jan 2022 22:55:35 +0000 (14:55 -0800)]
MAINTAINERS: add missing IPv4/IPv6 header paths
Add missing headers to the IP entry.
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 26 Jan 2022 20:24:24 +0000 (12:24 -0800)]
MAINTAINERS: add more files to eth PHY
include/linux/linkmode.h and include/linux/mii.h
do not match anything in MAINTAINERS. Looks like
they should be under Ethernet PHY.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Wed, 26 Jan 2022 16:52:15 +0000 (00:52 +0800)]
net: stmmac: dwmac-sun8i: use return val of readl_poll_timeout()
When readl_poll_timeout() timeout, we'd better directly use its return
value.
Before this patch:
[ 2.145528] dwmac-sun8i: probe of
4500000.ethernet failed with error -14
After this patch:
[ 2.138520] dwmac-sun8i: probe of
4500000.ethernet failed with error -110
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Wed, 26 Jan 2022 13:10:25 +0000 (15:10 +0200)]
net: bridge: vlan: fix single net device option dumping
When dumping vlan options for a single net device we send the same
entries infinitely because user-space expects a 0 return at the end but
we keep returning skb->len and restarting the dump on retry. Fix it by
returning the value from br_vlan_dump_dev() if it completed or there was
an error. The only case that must return skb->len is when the dump was
incomplete and needs to continue (-EMSGSIZE).
Reported-by: Benjamin Poirier <bpoirier@nvidia.com>
Fixes:
8dcea187088b ("net: bridge: vlan: add rtm definitions and dump support")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Jan 2022 13:46:18 +0000 (13:46 +0000)]
Merge branch 'stmmac-ptp-fix'
Mohammad Athari Bin Ismail says:
====================
Fix PTP issue in stmmac
This patch series to fix PTP issue in stmmac related to:
1/ PTP clock source configuration during initialization.
2/ PTP initialization during resume from suspend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohammad Athari Bin Ismail [Wed, 26 Jan 2022 09:47:23 +0000 (17:47 +0800)]
net: stmmac: skip only stmmac_ptp_register when resume from suspend
When resume from suspend, besides skipping PTP registration, it also
skipping PTP HW initialization. This could cause PTP clock not able to
operate properly when resume from suspend.
To fix this, only stmmac_ptp_register() is skipped when resume from
suspend.
Fixes:
fe1319291150 ("stmmac: Don't init ptp again when resume from suspend/hibernation")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohammad Athari Bin Ismail [Wed, 26 Jan 2022 09:47:22 +0000 (17:47 +0800)]
net: stmmac: configure PTP clock source prior to PTP initialization
For Intel platform, it is required to configure PTP clock source prior PTP
initialization in MAC. So, need to move ptp_clk_freq_config execution from
stmmac_ptp_register() to stmmac_init_ptp().
Fixes:
76da35dc99af ("stmmac: intel: Add PSE and PCH PTP clock source selection")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Wed, 26 Jan 2022 15:38:52 +0000 (16:38 +0100)]
Revert "ipv6: Honor all IPv6 PIO Valid Lifetime values"
This reverts commit
b75326c201242de9495ff98e5d5cff41d7fc0d9d.
This commit breaks Linux compatibility with USGv6 tests. The RFC this
commit was based on is actually an expired draft: no published RFC
currently allows the new behaviour it introduced.
Without full IETF endorsement, the flash renumbering scenario this
patch was supposed to enable is never going to work, as other IPv6
equipements on the same LAN will keep the 2 hours limit.
Fixes:
b75326c20124 ("ipv6: Honor all IPv6 PIO Valid Lifetime values")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 27 Jan 2022 09:23:26 +0000 (11:23 +0200)]
Merge tag 'rpmsg-v5.17-fixes' of git://git./linux/kernel/git/remoteproc/linux
Pull rpmsg fixes from Bjorn Andersson:
"The cdev cleanup in the rpmsg_char driver was not performed properly,
resulting in unpredicable behaviour when the parent remote processor
is stopped with any of the cdevs open by a client.
Two patches transitions the implementation to use cdev_device_add()
and cdev_del_device(), to capture the relationship between the two
objects, and relocates the incorrectly placed cdev_del()"
* tag 'rpmsg-v5.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
rpmsg: char: Fix race between the release of rpmsg_eptdev and cdev
rpmsg: char: Fix race between the release of rpmsg_ctrldev and cdev
Linus Torvalds [Thu, 27 Jan 2022 09:19:20 +0000 (11:19 +0200)]
Merge tag 'rproc-v5.17-fixes' of git://git./linux/kernel/git/remoteproc/linux
Pull remoteproc fix from Bjorn Andersson:
"The interaction between the various Qualcomm remoteproc drivers and
the Qualcomm 'QMP' driver (used to communicate with the
power-management hardware) was reworked in v5.17-rc1, but failed to
account for the new Kconfig dependency"
* tag 'rproc-v5.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
remoteproc: qcom: q6v5: fix service routines build errors
Miquel Raynal [Tue, 25 Jan 2022 12:14:26 +0000 (13:14 +0100)]
MAINTAINERS: Remove Harry Morris bouncing address
Harry's e-mail address from Cascoda bounces, I have not found any
contributions from him since 2018 so let's drop the Maintainer entry
from the CA8210 driver and mark it Orphan.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-7-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Miquel Raynal [Tue, 25 Jan 2022 12:14:25 +0000 (13:14 +0100)]
net: ieee802154: Return meaningful error codes from the netlink helpers
Returning -1 does not indicate anything useful.
Use a standard and meaningful error code instead.
Fixes:
a26c5fd7622d ("nl802154: add support for security layer")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-6-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Miquel Raynal [Tue, 25 Jan 2022 12:14:24 +0000 (13:14 +0100)]
net: ieee802154: ca8210: Stop leaking skb's
Upon error the ieee802154_xmit_complete() helper is not called. Only
ieee802154_wake_queue() is called manually. We then leak the skb
structure.
Free the skb structure upon error before returning.
Fixes:
ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-5-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Miquel Raynal [Tue, 25 Jan 2022 12:14:23 +0000 (13:14 +0100)]
net: ieee802154: at86rf230: Stop leaking skb's
Upon error the ieee802154_xmit_complete() helper is not called. Only
ieee802154_wake_queue() is called manually. In the Tx case we then leak
the skb structure.
Free the skb structure upon error before returning when appropriate.
As the 'is_tx = 0' cannot be moved in the complete handler because of a
possible race between the delay in switching to STATE_RX_AACK_ON and a
new interrupt, we introduce an intermediate 'was_tx' boolean just for
this purpose.
There is no Fixes tag applying here, many changes have been made on this
area and the issue kind of always existed.
Suggested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Miquel Raynal [Tue, 25 Jan 2022 12:14:22 +0000 (13:14 +0100)]
net: ieee802154: mcr20a: Fix lifs/sifs periods
These periods are expressed in time units (microseconds) while 40 and 12
are the number of symbol durations these periods will last. We need to
multiply them both with phy->symbol_duration in order to get these
values in microseconds.
Fixes:
8c6ad9cc5157 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-3-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Miquel Raynal [Tue, 25 Jan 2022 12:14:21 +0000 (13:14 +0100)]
net: ieee802154: hwsim: Ensure proper channel selection at probe time
Drivers are expected to set the PHY current_channel and current_page
according to their default state. The hwsim driver is advertising being
configured on channel 13 by default but that is not reflected in its own
internal pib structure. In order to ensure that this driver consider the
current channel as being 13 internally, we at least need to set the
pib->channel field to 13.
Fixes:
f25da51fdc38 ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[stefan@datenfreihafen.org: fixed assigment from page to channel]
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-2-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Jakub Kicinski [Thu, 27 Jan 2022 02:57:12 +0000 (18:57 -0800)]
Merge branch 'pid-introduce-helper-task_is_in_root_ns'
Leo Yan says:
====================
pid: Introduce helper task_is_in_root_ns()
This patch series introduces a helper function task_is_in_init_pid_ns()
to replace open code. The two patches are extracted from the original
series [1] for network subsystem.
As a plan, we can firstly land this patch set into kernel 5.18; there
have 5 patches are left out from original series [1], as a next step,
I will resend them for appropriate linux-next merging.
[1] https://lore.kernel.org/lkml/
20211208083320.472503-1-leo.yan@linaro.org/
====================
Link: https://lore.kernel.org/r/20220126050427.605628-1-leo.yan@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leo Yan [Wed, 26 Jan 2022 05:04:27 +0000 (13:04 +0800)]
connector/cn_proc: Use task_is_in_init_pid_ns()
This patch replaces open code with task_is_in_init_pid_ns() to check if
a task is in root PID namespace.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leo Yan [Wed, 26 Jan 2022 05:04:26 +0000 (13:04 +0800)]
pid: Introduce helper task_is_in_init_pid_ns()
Currently the kernel uses open code in multiple places to check if a
task is in the root PID namespace with the kind of format:
if (task_active_pid_ns(current) == &init_pid_ns)
do_something();
This patch creates a new helper function, task_is_in_init_pid_ns(), it
returns true if a passed task is in the root PID namespace, otherwise
returns false. So it will be used to replace open codes.
Suggested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Catherine Sullivan [Wed, 26 Jan 2022 00:38:43 +0000 (16:38 -0800)]
gve: Fix GFP flags when allocing pages
Use GFP_ATOMIC when allocating pages out of the hotpath,
continue to use GFP_KERNEL when allocating pages during setup.
GFP_KERNEL will allow blocking which allows it to succeed
more often in a low memory enviornment but in the hotpath we do
not want to allow the allocation to block.
Fixes:
f5cedc84a30d2 ("gve: Add transmit and receive support")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Link: https://lore.kernel.org/r/20220126003843.3584521-1-awogbemila@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal [Wed, 26 Jan 2022 11:54:54 +0000 (12:54 +0100)]
selftests: nft_concat_range: add test for reload with no element add/del
Add a specific test for the reload issue fixed with
commit
23c54263efd7cb ("netfilter: nft_set_pipapo: allocate pcpu scratch maps on clone").
Add to set, then flush set content + restore without other add/remove in
the transaction.
On kernels before the fix, this test case fails:
net,mac with reload [FAIL]
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso [Wed, 26 Jan 2022 00:46:58 +0000 (01:46 +0100)]
netfilter: nft_byteorder: track register operations
Cancel tracking for byteorder operation, otherwise selector + byteorder
operation is incorrectly reduced if source and destination registers are
the same.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Phil Sutter [Tue, 25 Jan 2022 19:06:03 +0000 (20:06 +0100)]
netfilter: nft_reject_bridge: Fix for missing reply from prerouting
Prior to commit
fa538f7cf05aa ("netfilter: nf_reject: add reject skbuff
creation helpers"), nft_reject_bridge did not assign to nskb->dev before
passing nskb on to br_forward(). The shared skbuff creation helpers
introduced in above commit do which seems to confuse br_forward() as
reject statements in prerouting hook won't emit a packet anymore.
Fix this by simply passing NULL instead of 'dev' to the helpers - they
use the pointer for just that assignment, nothing else.
Fixes:
fa538f7cf05aa ("netfilter: nf_reject: add reject skbuff creation helpers")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Mon, 24 Jan 2022 21:09:15 +0000 (22:09 +0100)]
selftests: netfilter: check stateless nat udp checksum fixup
Add a test that sends large udp packet (which is fragmented)
via a stateless nft nat rule, i.e. 'ip saddr set 10.2.3.4'
and check that the datagram is received by peer.
On kernels without
commit
4e1860a38637 ("netfilter: nft_payload: do not update layer 4 checksum when mangling fragments")',
this will fail with:
cmp: EOF on /tmp/tmp.V1q0iXJyQF which is empty
-rw------- 1 root root 4096 Jan 24 22:03 /tmp/tmp.Aaqnq4rBKS
-rw------- 1 root root 0 Jan 24 22:03 /tmp/tmp.V1q0iXJyQF
ERROR: in and output file mismatch when checking udp with stateless nat
FAIL: nftables v1.0.0 (Fearless Fosdick #2)
On patched kernels, this will show:
PASS: IP statless for ns2-PFp89amx
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Sun, 23 Jan 2022 14:45:54 +0000 (15:45 +0100)]
selftests: netfilter: reduce zone stress test running time
This selftests needs almost 3 minutes to complete, reduce the
insertes zones to 1000. Test now completes in about 20 seconds.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Sun, 23 Jan 2022 14:24:00 +0000 (15:24 +0100)]
netfilter: nft_ct: fix use after free when attaching zone template
The conversion erroneously removed the refcount increment.
In case we can use the percpu template, we need to increment
the refcount, else it will be released when the skb gets freed.
In case the slowpath is taken, the new template already has a
refcount of 1.
Fixes:
719774377622 ("netfilter: conntrack: convert to refcount_t api")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Geert Uytterhoeven [Sun, 23 Jan 2022 12:57:17 +0000 (13:57 +0100)]
netfilter: Remove flowtable relics
NF_FLOW_TABLE_IPV4 and NF_FLOW_TABLE_IPV6 are invisble, selected by
nothing (so they can no longer be enabled), and their last real users
have been removed (nf_flow_table_ipv6.c is empty).
Clean up the leftovers.
Fixes:
c42ba4290b2147aa ("netfilter: flowtable: remove ipv4/ipv6 modules")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Wed, 26 Jan 2022 15:45:49 +0000 (15:45 +0000)]
Merge branch 'lan966x-fixes'
Horatiu Vultur says:
====================
net: lan966x: Fixes for sleep in atomic context
This patch series contains 2 fixes for lan966x that is sleeping in atomic
context. The first patch fixes the injection of the frames while the second
one fixes the updating of the MAC table.
v1->v2:
- correct the fix tag in the second patch, it was using the wrong sha.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 25 Jan 2022 11:48:16 +0000 (12:48 +0100)]
net: lan966x: Fix sleep in atomic context when updating MAC table
The function lan966x_mac_wait_for_completion is used to poll the status
of the MAC table using the function readx_poll_timeout. The problem with
this function is that is called also from atomic context. Therefore
update the function to use readx_poll_timeout_atomic.
Fixes:
e18aba8941b40b ("net: lan966x: add mactable support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 25 Jan 2022 11:48:15 +0000 (12:48 +0100)]
net: lan966x: Fix sleep in atomic context when injecting frames
On lan966x, when injecting a frame it was polling the register
QS_INJ_STATUS to see if it can continue with the injection of the frame.
The problem was that it was using readx_poll_timeout which could sleep
in atomic context.
This patch fixes this issue by using readx_poll_timeout_atomic.
Fixes:
d28d6d2e37d10d ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 26 Jan 2022 15:40:02 +0000 (15:40 +0000)]
Merge branch 'dev_addr-const-fixes'
Jakub Kicinski says:
====================
ethernet: fix some esoteric drivers after netdev->dev_addr constification
Looking at recent fixes for drivers which don't get included with
allmodconfig builds I thought it's worth grepping for more instances of:
dev->dev_addr\[.*\] =
This set contains the fixes.
v2: add last 3 patches which fix drivers for the RiscPC ARM platform.
Thanks to Arnd Bergmann for explaining how to build test that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 26 Jan 2022 00:38:01 +0000 (16:38 -0800)]
ethernet: seeq/ether3: don't write directly to netdev->dev_addr
netdev->dev_addr is const now.
Compile tested rpc_defconfig w/ GCC 8.5.
Fixes:
adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 26 Jan 2022 00:38:00 +0000 (16:38 -0800)]
ethernet: 8390/etherh: don't write directly to netdev->dev_addr
netdev->dev_addr is const now.
Compile tested rpc_defconfig w/ GCC 8.5.
Fixes:
adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 26 Jan 2022 00:37:59 +0000 (16:37 -0800)]
ethernet: i825xx: don't write directly to netdev->dev_addr
netdev->dev_addr is const now.
Compile tested rpc_defconfig w/ GCC 8.5.
Fixes:
adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 26 Jan 2022 00:37:58 +0000 (16:37 -0800)]
ethernet: broadcom/sb1250-mac: don't write directly to netdev->dev_addr
netdev->dev_addr is const now.
Compile tested bigsur_defconfig and sb1250_swarm_defconfig.
Fixes:
adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 26 Jan 2022 00:37:57 +0000 (16:37 -0800)]
ethernet: tundra: don't write directly to netdev->dev_addr
netdev->dev_addr is const now.
Maintain the questionable offsetting in ndo_set_mac_address.
Compile tested holly_defconfig and mpc7448_hpc2_defconfig.
Fixes:
adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 26 Jan 2022 00:37:56 +0000 (16:37 -0800)]
ethernet: 3com/typhoon: don't write directly to netdev->dev_addr
This driver casts off the const and writes directly to netdev->dev_addr.
This will result in a MAC address tree corruption and a warning.
Compile tested ppc6xx_defconfig.
Fixes:
adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Mikityanskiy [Tue, 25 Jan 2022 10:06:54 +0000 (12:06 +0200)]
sch_htb: Fail on unsupported parameters when offload is requested
The current implementation of HTB offload doesn't support some
parameters. Instead of ignoring them, actively return the EINVAL error
when they are set to non-defaults.
As this patch goes to stable, the driver API is not changed here. If
future drivers support more offload parameters, the checks can be moved
to the driver side.
Note that the buffer and cbuffer parameters are also not supported, but
the tc userspace tool assigns some default values derived from rate and
ceil, and identifying these defaults in sch_htb would be unreliable, so
they are still ignored.
Fixes:
d03b195b5aa0 ("sch_htb: Hierarchical QoS hardware offload")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220125100654.424570-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Tue, 25 Jan 2022 18:16:03 +0000 (20:16 +0200)]
Merge tag 'nfs-for-5.17-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client updates from Anna Schumaker:
"New Features:
- Basic handling for case insensitive filesystems
- Initial support for fs_locations and server trunking
Bugfixes and Cleanups:
- Cleanups to how the "struct cred *" is handled for the
nfs_access_entry
- Ensure the server has an up to date ctimes before hardlinking or
renaming
- Update 'blocks used' after writeback, fallocate, and clone
- nfs_atomic_open() fixes
- Improvements to sunrpc tracing
- Various null check & indenting related cleanups
- Some improvements to the sunrpc sysfs code:
- Use default_groups in kobj_type
- Fix some potential races and reference leaks
- A few tracepoint cleanups in xprtrdma"
[ This should have gone in during the merge window, but didn't. The
original pull request - sent during the merge window - had gotten
marked as spam and discarded due missing DKIM headers in the email
from Anna. - Linus ]
* tag 'nfs-for-5.17-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (35 commits)
SUNRPC: Don't dereference xprt->snd_task if it's a cookie
xprtrdma: Remove definitions of RPCDBG_FACILITY
xprtrdma: Remove final dprintk call sites from xprtrdma
sunrpc: Fix potential race conditions in rpc_sysfs_xprt_state_change()
net/sunrpc: fix reference count leaks in rpc_sysfs_xprt_state_change
NFSv4.1 test and add 4.1 trunking transport
SUNRPC allow for unspecified transport time in rpc_clnt_add_xprt
NFSv4 handle port presence in fs_location server string
NFSv4 expose nfs_parse_server_name function
NFSv4.1 query for fs_location attr on a new file system
NFSv4 store server support for fs_location attribute
NFSv4 remove zero number of fs_locations entries error check
NFSv4: nfs_atomic_open() can race when looking up a non-regular file
NFSv4: Handle case where the lookup of a directory fails
NFSv42: Fallocate and clone should also request 'blocks used'
NFSv4: Allow writebacks to request 'blocks used'
SUNRPC: use default_groups in kobj_type
NFS: use default_groups in kobj_type
NFS: Fix the verifier for case sensitive filesystem in nfs_atomic_open()
NFS: Add a helper to remove case-insensitive aliases
...
Tvrtko Ursulin [Tue, 19 Oct 2021 12:27:10 +0000 (13:27 +0100)]
drm/i915: Flush TLBs before releasing backing store
We need to flush TLBs before releasing backing store otherwise userspace
is able to encounter stale entries if a) it is not declaring access to
certain buffers and b) it races with the backing store release from a
such undeclared execution already executing on the GPU in parallel.
The approach taken is to mark any buffer objects which were ever bound
to the GPU and to trigger a serialized TLB flush when their backing
store is released.
Alternatively the flushing could be done on VMA unbind, at which point
we would be able to ascertain whether there is potential a parallel GPU
execution (which could race), but essentially it boils down to paying
the cost of TLB flushes potentially needlessly at VMA unbind time (when
the backing store is not known to be going away so not needed for
safety), versus potentially needlessly at backing store relase time
(since we at that point cannot tell whether there is anything executing
on the GPU which uses that object).
Thereforce simplicity of implementation has been chosen for now with
scope to benchmark and refine later as required.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Bogendoerfer [Tue, 25 Jan 2022 14:40:06 +0000 (15:40 +0100)]
amd: declance: use eth_hw_addr_set()
Copy scattered mac address octets into an array then eth_hw_addr_set().
Fixes:
adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20220125144007.64407-1-tsbogend@alpha.franken.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Tue, 25 Jan 2022 16:29:10 +0000 (18:29 +0200)]
Merge tag 'for-5.17-rc1-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Several fixes for defragmentation that got broken in 5.16 after
refactoring and added subpage support. The observed bugs are excessive
IO or uninterruptible ioctl.
All stable material"
* tag 'for-5.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: update writeback index when starting defrag
btrfs: add back missing dirty page rate limiting to defrag
btrfs: fix deadlock when reserving space during defrag
btrfs: defrag: properly update range->start for autodefrag
btrfs: defrag: fix wrong number of defragged sectors
btrfs: allow defrag to be interruptible
btrfs: fix too long loop when defragging a 1 byte file
Yufeng Mo [Tue, 25 Jan 2022 07:03:12 +0000 (15:03 +0800)]
net: hns3: handle empty unknown interrupt for VF
Since some interrupt states may be cleared by hardware, the driver
may receive an empty interrupt. Currently, the VF driver directly
disables the vector0 interrupt in this case. As a result, the VF
is unavailable. Therefore, the vector0 interrupt should be enabled
in this case.
Fixes:
b90fcc5bd904 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 24 Jan 2022 17:22:49 +0000 (09:22 -0800)]
net: fec_mpc52xx: don't discard const from netdev->dev_addr
Recent changes made netdev->dev_addr const, and it's passed
directly to mpc52xx_fec_set_paddr().
Similar problem exists on the probe patch, the driver needs
to call eth_hw_addr_set().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes:
adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toke Høiland-Jørgensen [Mon, 24 Jan 2022 14:35:29 +0000 (15:35 +0100)]
net: cpsw: Properly initialise struct page_pool_params
The cpsw driver didn't properly initialise the struct page_pool_params
before calling page_pool_create(), which leads to crashes after the struct
has been expanded with new parameters.
The second Fixes tag below is where the buggy code was introduced, but
because the code was moved around this patch will only apply on top of the
commit in the first Fixes tag.
Fixes:
c5013ac1dd0e ("net: ethernet: ti: cpsw: move set of common functions in cpsw_priv")
Fixes:
9ed4050c0d75 ("net: ethernet: ti: cpsw: add XDP support")
Reported-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangyu Hua [Mon, 24 Jan 2022 03:29:54 +0000 (11:29 +0800)]
yam: fix a memory leak in yam_siocdevprivate()
ym needs to be free when ym->cmd != SIOCYAMSMCS.
Fixes:
0781168e23a2 ("yam: fix a missing-check bug")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Sun, 23 Jan 2022 15:54:58 +0000 (23:54 +0800)]
net: stmmac: reduce unnecessary wakeups from eee sw timer
Currently, on EEE capable platforms, if EEE SW timer is used, the SW
timer cause 1 wakeup/s even if the TX has successfully entered EEE.
Remove this unnecessary wakeup by only calling mod_timer() if we
haven't successfully entered EEE.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 25 Jan 2022 06:02:46 +0000 (08:02 +0200)]
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- Fix panic whe both KASAN and KPROBEs are enabled
- Avoid alignment faults in copy_*_kernel_nofault()
- Align SMP alternatives in modules
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9180/1: Thumb2: align ALT_UP() sections in modules sufficiently
ARM: 9179/1: uaccess: avoid alignment faults in copy_[from|to]_kernel_nofault
ARM: 9170/1: fix panic when kasan and kprobe are enabled
Jakub Kicinski [Mon, 24 Jan 2022 20:17:58 +0000 (12:17 -0800)]
Merge tag 'linux-can-fixes-for-5.17-
20220124' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-01-24
The first patch updates the email address of Brian Silverman from his
former employer to his private address.
The next patch fixes DT bindings information for the tcan4x5x SPI CAN
driver.
The following patch targets the m_can driver and fixes the
introduction of FIFO bulk read support.
Another patch for the tcan4x5x driver, which fixes the max register
value for the regmap config.
The last patch for the flexcan driver marks the RX mailbox support for
the MCF5441X as support.
* tag 'linux-can-fixes-for-5.17-
20220124' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: flexcan: mark RX via mailboxes as supported on MCF5441X
can: tcan4x5x: regmap: fix max register value
can: m_can: m_can_fifo_{read,write}: don't read or write from/to FIFO if length is 0
dt-bindings: can: tcan4x5x: fix mram-cfg RX FIFO config
mailmap: update email address of Brian Silverman
====================
Link: https://lore.kernel.org/r/20220124175955.3464134-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde [Fri, 21 Jan 2022 08:22:34 +0000 (09:22 +0100)]
can: flexcan: mark RX via mailboxes as supported on MCF5441X
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
The flexcan IP core on the MCF5441X cannot receive CAN RTR messages
via mailboxes. However the mailbox mode is more performant. The commit
|
1c45f5778a3b ("can: flexcan: add ethtool support to change rx-rtr setting during runtime")
added support to switch from FIFO to mailbox mode on these cores.
After testing the mailbox mode on the MCF5441X by Angelo Dureghello,
this patch marks it (without RTR capability) as supported. Further the
IP core overview table is updated, that RTR reception via mailboxes is
not supported.
Link: https://lore.kernel.org/all/20220121084425.3141218-1-mkl@pengutronix.de
Tested-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Fri, 14 Jan 2022 17:50:54 +0000 (18:50 +0100)]
can: tcan4x5x: regmap: fix max register value
The MRAM of the tcan4x5x has a size of 2K and starts at 0x8000. There
are no further registers in the tcan4x5x making 0x87fc the biggest
addressable register.
This patch fixes the max register value of the regmap config from
0x8ffc to 0x87fc.
Fixes:
6e1caaf8ed22 ("can: tcan4x5x: fix max register value")
Link: https://lore.kernel.org/all/20220119064011.2943292-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Fri, 14 Jan 2022 14:35:01 +0000 (15:35 +0100)]
can: m_can: m_can_fifo_{read,write}: don't read or write from/to FIFO if length is 0
In order to optimize FIFO access, especially on m_can cores attached
to slow busses like SPI, in patch
|
e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")
bulk read/write support has been added to the m_can_fifo_{read,write}
functions.
That change leads to the tcan driver to call
regmap_bulk_{read,write}() with a length of 0 (for CAN frames with 0
data length). regmap treats this as an error:
| tcan4x5x spi1.0 tcan4x5x0: FIFO write returned -22
This patch fixes the problem by not calling the
cdev->ops->{read,write)_fifo() in case of a 0 length read/write.
Fixes:
e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20220114155751.2651888-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Reported-by: Michael Anochin <anochin@photo-meter.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Fri, 14 Jan 2022 17:47:41 +0000 (18:47 +0100)]
dt-bindings: can: tcan4x5x: fix mram-cfg RX FIFO config
This tcan4x5x only comes with 2K of MRAM, a RX FIFO with a dept of 32
doesn't fit into the MRAM. Use a depth of 16 instead.
Fixes:
4edd396a1911 ("dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver")
Link: https://lore.kernel.org/all/20220119062951.2939851-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 10 Jan 2022 08:20:19 +0000 (09:20 +0100)]
mailmap: update email address of Brian Silverman
Brian Silverman's address at bluerivertech.com is not valid anymore,
use Brian's private email address instead.
Link: https://lore.kernel.org/all/20220110082359.2019735-1-mkl@pengutronix.de
Cc: Brian Silverman <bsilver16384@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Filipe Manana [Thu, 20 Jan 2022 17:41:17 +0000 (17:41 +0000)]
btrfs: update writeback index when starting defrag
When starting a defrag, we should update the writeback index of the
inode's mapping in case it currently has a value beyond the start of the
range we are defragging. This can help performance and often result in
getting less extents after writeback - for e.g., if the current value
of the writeback index sits somewhere in the middle of a range that
gets dirty by the defrag, then after writeback we can get two smaller
extents instead of a single, larger extent.
We used to have this before the refactoring in 5.16, but it was removed
without any reason to do so. Originally it was added in kernel 3.1, by
commit
2a0f7f5769992b ("Btrfs: fix recursive auto-defrag"), in order to
fix a loop with autodefrag resulting in dirtying and writing pages over
and over, but some testing on current code did not show that happening,
at least with the test described in that commit.
So add back the behaviour, as at the very least it is a nice to have
optimization.
Fixes:
7b508037d4cac3 ("btrfs: defrag: use defrag_one_cluster() to implement btrfs_defrag_file()")
CC: stable@vger.kernel.org # 5.16
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Thu, 20 Jan 2022 17:11:52 +0000 (17:11 +0000)]
btrfs: add back missing dirty page rate limiting to defrag
A defrag operation can dirty a lot of pages, specially if operating on
the entire file or a large file range. Any task dirtying pages should
periodically call balance_dirty_pages_ratelimited(), as stated in that
function's comments, otherwise they can leave too many dirty pages in
the system. This is what we did before the refactoring in 5.16, and
it should have remained, just like in the buffered write path and
relocation. So restore that behaviour.
Fixes:
7b508037d4cac3 ("btrfs: defrag: use defrag_one_cluster() to implement btrfs_defrag_file()")
CC: stable@vger.kernel.org # 5.16
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Thu, 20 Jan 2022 14:27:56 +0000 (14:27 +0000)]
btrfs: fix deadlock when reserving space during defrag
When defragging we can end up collecting a range for defrag that has
already pages under delalloc (dirty), as long as the respective extent
map for their range is not mapped to a hole, a prealloc extent or
the extent map is from an old generation.
Most of the time that is harmless from a functional perspective at
least, however it can result in a deadlock:
1) At defrag_collect_targets() we find an extent map that meets all
requirements but there's delalloc for the range it covers, and we add
its range to list of ranges to defrag;
2) The defrag_collect_targets() function is called at defrag_one_range(),
after it locked a range that overlaps the range of the extent map;
3) At defrag_one_range(), while the range is still locked, we call
defrag_one_locked_target() for the range associated to the extent
map we collected at step 1);
4) Then finally at defrag_one_locked_target() we do a call to
btrfs_delalloc_reserve_space(), which will reserve data and metadata
space. If the space reservations can not be satisfied right away, the
flusher might be kicked in and start flushing delalloc and wait for
the respective ordered extents to complete. If this happens we will
deadlock, because both flushing delalloc and finishing an ordered
extent, requires locking the range in the inode's io tree, which was
already locked at defrag_collect_targets().
So fix this by skipping extent maps for which there's already delalloc.
Fixes:
eb793cf857828d ("btrfs: defrag: introduce helper to collect target file extents")
CC: stable@vger.kernel.org # 5.16
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Jisheng Zhang [Sun, 23 Jan 2022 12:27:58 +0000 (20:27 +0800)]
net: stmmac: remove unused members in struct stmmac_priv
The tx_coalesce and mii_irq are not used at all now, so remove them.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sun, 23 Jan 2022 06:53:46 +0000 (07:53 +0100)]
net: atlantic: Use the bitmap API instead of hand-writing it
Simplify code by using bitmap_weight() and bitmap_zero() instead of
hand-writing these functions.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 22 Jan 2022 11:40:56 +0000 (06:40 -0500)]
ping: fix the sk_bound_dev_if match in ping_lookup
When 'ping' changes to use PING socket instead of RAW socket by:
# sysctl -w net.ipv4.ping_group_range="0 100"
the selftests 'router_broadcast.sh' will fail, as such command
# ip vrf exec vrf-h1 ping -I veth0 198.51.100.255 -b
can't receive the response skb by the PING socket. It's caused by mismatch
of sk_bound_dev_if and dif in ping_rcv() when looking up the PING socket,
as dif is vrf-h1 if dif's master was set to vrf-h1.
This patch is to fix this regression by also checking the sk_bound_dev_if
against sdif so that the packets can stil be received even if the socket
is not bound to the vrf device but to the real iif.
Fixes:
c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wen Gu [Sat, 22 Jan 2022 09:43:09 +0000 (17:43 +0800)]
net/smc: Transitional solution for clcsock race issue
We encountered a crash in smc_setsockopt() and it is caused by
accessing smc->clcsock after clcsock was released.
BUG: kernel NULL pointer dereference, address:
0000000000000020
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 50309 Comm: nginx Kdump: loaded Tainted: G E 5.16.0-rc4+ #53
RIP: 0010:smc_setsockopt+0x59/0x280 [smc]
Call Trace:
<TASK>
__sys_setsockopt+0xfc/0x190
__x64_sys_setsockopt+0x20/0x30
do_syscall_64+0x34/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f16ba83918e
</TASK>
This patch tries to fix it by holding clcsock_release_lock and
checking whether clcsock has already been released before access.
In case that a crash of the same reason happens in smc_getsockopt()
or smc_switch_to_fallback(), this patch also checkes smc->clcsock
in them too. And the caller of smc_switch_to_fallback() will identify
whether fallback succeeds according to the return value.
Fixes:
fd57770dd198 ("net/smc: wait for pending work before clcsock release_sock")
Link: https://lore.kernel.org/lkml/5dd7ffd1-28e2-24cc-9442-1defec27375e@linux.ibm.com/T/
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sukadev Bhattiprolu [Sat, 22 Jan 2022 02:59:21 +0000 (18:59 -0800)]
ibmvnic: remove unused ->wait_capability
With previous bug fix, ->wait_capability flag is no longer needed and can
be removed.
Fixes:
249168ad07cd ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sukadev Bhattiprolu [Sat, 22 Jan 2022 02:59:20 +0000 (18:59 -0800)]
ibmvnic: don't spin in tasklet
ibmvnic_tasklet() continuously spins waiting for responses to all
capability requests. It does this to avoid encountering an error
during initialization of the vnic. However if there is a bug in the
VIOS and we do not receive a response to one or more queries the
tasklet ends up spinning continuously leading to hard lock ups.
If we fail to receive a message from the VIOS it is reasonable to
timeout the login attempt rather than spin indefinitely in the tasklet.
Fixes:
249168ad07cd ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sukadev Bhattiprolu [Sat, 22 Jan 2022 02:59:19 +0000 (18:59 -0800)]
ibmvnic: init ->running_cap_crqs early
We use ->running_cap_crqs to determine when the ibmvnic_tasklet() should
send out the next protocol message type. i.e when we get back responses
to all our QUERY_CAPABILITY CRQs we send out REQUEST_CAPABILITY crqs.
Similiary, when we get responses to all the REQUEST_CAPABILITY crqs, we
send out the QUERY_IP_OFFLOAD CRQ.
We currently increment ->running_cap_crqs as we send out each CRQ and
have the ibmvnic_tasklet() send out the next message type, when this
running_cap_crqs count drops to 0.
This assumes that all the CRQs of the current type were sent out before
the count drops to 0. However it is possible that we send out say 6 CRQs,
get preempted and receive all the 6 responses before we send out the
remaining CRQs. This can result in ->running_cap_crqs count dropping to
zero before all messages of the current type were sent and we end up
sending the next protocol message too early.
Instead initialize the ->running_cap_crqs upfront so the tasklet will
only send the next protocol message after all responses are received.
Use the cap_reqs local variable to also detect any discrepancy (either
now or in future) in the number of capability requests we actually send.
Currently only send_query_cap() is affected by this behavior (of sending
next message early) since it is called from the worker thread (during
reset) and from application thread (during ->ndo_open()) and they can be
preempted. send_request_cap() is only called from the tasklet which
processes CRQ responses sequentially, is not be affected. But to
maintain the existing symmtery with send_query_capability() we update
send_request_capability() also.
Fixes:
249168ad07cd ("ibmvnic: Make CRQ interrupt tasklet wait for all capabilities crqs")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sukadev Bhattiprolu [Sat, 22 Jan 2022 02:59:18 +0000 (18:59 -0800)]
ibmvnic: Allow extra failures before disabling
If auto-priority-failover (APF) is enabled and there are at least two
backing devices of different priorities, some resets like fail-over,
change-param etc can cause at least two back to back failovers. (Failover
from high priority backing device to lower priority one and then back
to the higher priority one if that is still functional).
Depending on the timimg of the two failovers it is possible to trigger
a "hard" reset and for the hard reset to fail due to failovers. When this
occurs, the driver assumes that the network is unstable and disables the
VNIC for a 60-second "settling time". This in turn can cause the ethtool
command to fail with "No such device" while the vnic automatically recovers
a little while later.
Given that it's possible to have two back to back failures, allow for extra
failures before disabling the vnic for the settling time.
Fixes:
f15fde9d47b8 ("ibmvnic: delay next reset if hard reset fails")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 22 Jan 2022 00:57:31 +0000 (16:57 -0800)]
ipv4: fix ip option filtering for locally generated fragments
During IP fragmentation we sanitize IP options. This means overwriting
options which should not be copied with NOPs. Only the first fragment
has the original, full options.
ip_fraglist_prepare() copies the IP header and options from previous
fragment to the next one. Commit
19c3401a917b ("net: ipv4: place control
buffer handling away from fragmentation iterators") moved sanitizing
options before ip_fraglist_prepare() which means options are sanitized
and then overwritten again with the old values.
Fixing this is not enough, however, nor did the sanitization work
prior to aforementioned commit.
ip_options_fragment() (which does the sanitization) uses ipcb->opt.optlen
for the length of the options. ipcb->opt of fragments is not populated
(it's 0), only the head skb has the state properly built. So even when
called at the right time ip_options_fragment() does nothing. This seems
to date back all the way to v2.5.44 when the fast path for pre-fragmented
skbs had been introduced. Prior to that ip_options_build() would have been
called for every fragment (in fact ever since v2.5.44 the fragmentation
handing in ip_options_build() has been dead code, I'll clean it up in
-next).
In the original patch (see Link) caixf mentions fixing the handling
for fragments other than the second one, but I'm not sure how _any_
fragment could have had their options sanitized with the code
as it stood.
Tested with python (MTU on lo lowered to 1000 to force fragmentation):
import socket
s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
s.setsockopt(socket.IPPROTO_IP, socket.IP_OPTIONS,
bytearray([7,4,5,192, 20|0x80,4,1,0]))
s.sendto(b'1'*2000, ('127.0.0.1', 1234))
Before:
IP (tos 0x0, ttl 64, id 1053, offset 0, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
localhost.36500 > localhost.search-agent: UDP, length 2000
IP (tos 0x0, ttl 64, id 1053, offset 968, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
localhost > localhost: udp
IP (tos 0x0, ttl 64, id 1053, offset 1936, flags [none], proto UDP (17), length 100, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
localhost > localhost: udp
After:
IP (tos 0x0, ttl 96, id 42549, offset 0, flags [+], proto UDP (17), length 996, options (RR [bad length 4] [bad ptr 5] 192.148.4.1,,RA value 256))
localhost.51607 > localhost.search-agent: UDP, bad length 2000 > 960
IP (tos 0x0, ttl 96, id 42549, offset 968, flags [+], proto UDP (17), length 996, options (NOP,NOP,NOP,NOP,RA value 256))
localhost > localhost: udp
IP (tos 0x0, ttl 96, id 42549, offset 1936, flags [none], proto UDP (17), length 100, options (NOP,NOP,NOP,NOP,RA value 256))
localhost > localhost: udp
RA (20 | 0x80) is now copied as expected, RR (7) is "NOPed out".
Link: https://lore.kernel.org/netdev/20220107080559.122713-1-ooppublic@163.com/
Fixes:
19c3401a917b ("net: ipv4: place control buffer handling away from fragmentation iterators")
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: caixf <ooppublic@163.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jianguo Wu [Fri, 21 Jan 2022 09:15:31 +0000 (17:15 +0800)]
net-procfs: show net devices bound packet types
After commit:
7866a621043f ("dev: add per net_device packet type chains"),
we can not get packet types that are bound to a specified net device by
/proc/net/ptype, this patch fix the regression.
Run "tcpdump -i ens192 udp -nns0" Before and after apply this patch:
Before:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
After:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
ALL ens192 tpacket_rcv
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
v1 -> v2:
- fix the regression rather than adding new /proc API as
suggested by Stephen Hemminger.
Fixes:
7866a621043f ("dev: add per net_device packet type chains")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 21 Jan 2022 08:25:18 +0000 (16:25 +0800)]
bonding: use rcu_dereference_rtnl when get bonding active slave
bond_option_active_slave_get_rcu() should not be used in rtnl_mutex as it
use rcu_dereference(). Replace to rcu_dereference_rtnl() so we also can use
this function in rtnl protected context.
With this update, we can rmeove the rcu_read_lock/unlock in
bonding .ndo_eth_ioctl and .get_ts_info.
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes:
94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Wed, 19 Jan 2022 16:44:55 +0000 (17:44 +0100)]
net: sfp: ignore disabled SFP node
Commit
ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).
We need to ignore disabled SFP bus node.
Fixes:
ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 23 Jan 2022 15:52:42 +0000 (17:52 +0200)]
Merge tag 'powerpc-5.17-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- A series of bpf fixes, including an oops fix and some codegen fixes.
- Fix a regression in syscall_get_arch() for compat processes.
- Fix boot failure on some 32-bit systems with KASAN enabled.
- A couple of other build/minor fixes.
Thanks to Athira Rajeev, Christophe Leroy, Dmitry V. Levin, Jiri Olsa,
Johan Almbladh, Maxime Bizon, Naveen N. Rao, and Nicholas Piggin.
* tag 'powerpc-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Mask SRR0 before checking against the masked NIP
powerpc/perf: Only define power_pmu_wants_prompt_pmi() for CONFIG_PPC64
powerpc/32s: Fix kasan_init_region() for KASAN
powerpc/time: Fix build failure due to do_hard_irq_enable() on PPC32
powerpc/audit: Fix syscall_get_arch()
powerpc64/bpf: Limit 'ldbrx' to processors compliant with ISA v2.06
tools/bpf: Rename 'struct event' to avoid naming conflict
powerpc/bpf: Update ldimm64 instructions during extra pass
powerpc32/bpf: Fix codegen for bpf-to-bpf calls
bpf: Guard against accessing NULL pt_regs in bpf_get_task_stack()
Linus Torvalds [Sun, 23 Jan 2022 15:45:00 +0000 (17:45 +0200)]
Merge tag 'irq_urgent_for_v5.17_rc2' of git://git./linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
"A single use-after-free fix in the PCI MSI irq domain allocation path"
* tag 'irq_urgent_for_v5.17_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI/MSI: Prevent UAF in error path
Linus Torvalds [Sun, 23 Jan 2022 15:35:27 +0000 (17:35 +0200)]
Merge tag 'sched_urgent_for_v5.17_rc2' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
"A bunch of fixes: forced idle time accounting, utilization values
propagation in the sched hierarchies and other minor cleanups and
improvements"
* tag 'sched_urgent_for_v5.17_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel/sched: Remove dl_boosted flag comment
sched: Avoid double preemption in __cond_resched_*lock*()
sched/fair: Fix all kernel-doc warnings
sched/core: Accounting forceidle time for all tasks except idle task
sched/pelt: Relax the sync of load_sum with load_avg
sched/pelt: Relax the sync of runnable_sum with runnable_avg
sched/pelt: Continue to relax the sync of util_sum with util_avg
sched/pelt: Relax the sync of util_sum with util_avg
psi: Fix uaf issue when psi trigger is destroyed while being polled
Linus Torvalds [Sun, 23 Jan 2022 15:31:24 +0000 (17:31 +0200)]
Merge tag 'perf_urgent_for_v5.17_rc2' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Add support for accessing the general purpose counters on Alder Lake
via MMIO
- Add new LBR format v7 support which is v5 modulo TSX
- Fix counter enumeration on Alder Lake hybrids
- Overhaul how context time updates are done and get rid of
perf_event::shadow_ctx_time.
- The usual amount of fixes: event mask correction, supported event
types reporting, etc.
* tag 'perf_urgent_for_v5.17_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/perf: Avoid warning for Arch LBR without XSAVE
perf/x86/intel/uncore: Add IMC uncore support for ADL
perf/x86/intel/lbr: Add static_branch for LBR INFO flags
perf/x86/intel/lbr: Support LBR format V7
perf/x86/rapl: fix AMD event handling
perf/x86/intel/uncore: Fix CAS_COUNT_WRITE issue for ICX
perf/x86/intel: Add a quirk for the calculation of the number of counters on Alder Lake
perf: Fix perf_event_read_local() time
Linus Torvalds [Sun, 23 Jan 2022 08:12:53 +0000 (10:12 +0200)]
Linux 5.17-rc1