OSDN Git Service
Kevin Hilman [Mon, 20 Jul 2009 16:09:23 +0000 (09:09 -0700)]
OMAP3: Overo: add missing pen-down GPIO definition
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Thu, 4 Jun 2009 22:57:10 +0000 (15:57 -0700)]
OMAP: GPIO: clear/restore level/edge detect settings on mask/unmask
If IRQ triggering is enabled, it can trigger a pending interrupt
even for masked interrupts. Any pending GPIO interrupts can
prevent the powerdomain from hitting retention.
Problem found, reported and additional review and testing by Chunquiu
Wang.
Tested-by: Chunquiu Wang <cqwang@motorola.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Jouni Hogander [Wed, 29 Oct 2008 10:06:04 +0000 (12:06 +0200)]
OMAP3: PM: Fix wrong sequence in suspend.
Powerdomain previous state is checked after restoring new states in
suspend. This patch fixes this problem.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Eero Nurkkala [Tue, 23 Jun 2009 09:53:29 +0000 (12:53 +0300)]
OMAP: PM: CPUfreq: obey min/max settings of policy
Use the min/max settings from CPUfreq policy rather than
processor defined min/max settings.
Without this patch, it's possible to scale frequency outside
the current policy range.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Wed, 1 Jul 2009 04:02:45 +0000 (21:02 -0700)]
OMAP2/3/4: UART: allow in-order port traversal
Use list_add_tail() when adding discovered UART ports. This is so
traversal using list_for_each_entry() will traverse the list in the
order they were found.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Mon, 27 Apr 2009 19:27:36 +0000 (12:27 -0700)]
OMAP2/3/4: UART: Allow per-UART disabling wakeup for serial ports
This patch causes the OMAP uarts to honor the sysfs power/wakeup file
for IOPAD wakeups. Before the OMAP was always woken up from off mode
on a rs232 signal change. This patch also creates a different
platform device for each serial port so that the wakeup properties can
be control per port.
By default, IOPAD wakeups are enabled for each UART. To disable,
# echo disabled > /sys/devices/platform/serial8250.0/power/wakeup
Where serial8250.0 can be replaced by .1, or .2 to control the other
ports.
Original idea and original patch from Russ Dill <russ.dill@gmail.com>
Cc: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tero Kristo [Thu, 5 Mar 2009 14:32:23 +0000 (16:32 +0200)]
OMAP3: Fixed crash bug with serial + suspend
It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.
Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path. Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Wed, 24 Jun 2009 17:32:03 +0000 (10:32 -0700)]
OMAP4: UART: cleanup special case IRQ handling
Streamline the OMAP4 special IRQ assignments by putting inside
normal init loop instead of having a separate loop.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Wed, 24 Jun 2009 18:39:18 +0000 (11:39 -0700)]
OMAP3: PM: Do not build suspend code if SUSPEND is not enabled
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Tue, 5 May 2009 23:34:25 +0000 (16:34 -0700)]
OMAP3: PM: prevent module wakeups from waking IVA2
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Mon, 27 Apr 2009 23:14:54 +0000 (16:14 -0700)]
OMAP3: PM: Clear pending PRCM reset flags on init
Any pending reset flags can prevent retention. Ensure they are all
cleared during boot.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Mon, 27 Apr 2009 14:50:23 +0000 (07:50 -0700)]
OMAP3: PM: Ensure PRCM interrupts are cleared at boot
Any pending PRCM interrupts can prevent retention. Ensure
they are cleared during boot.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Tue, 9 Jun 2009 18:45:30 +0000 (11:45 -0700)]
OMAP3: PM: CM_REGADDR macros using wrong name
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Kevin Hilman [Wed, 10 Jun 2009 16:02:25 +0000 (09:02 -0700)]
OMAP2/3: PM: make PM __init calls static
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Linus Torvalds [Sat, 1 Aug 2009 00:40:45 +0000 (17:40 -0700)]
Linux 2.6.31-rc5
Linus Torvalds [Fri, 31 Jul 2009 19:17:37 +0000 (12:17 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: bump up nr_to_write in xfs_vm_writepage
xfs: reduce bmv_count in xfs_vn_fiemap
Linus Torvalds [Fri, 31 Jul 2009 19:10:26 +0000 (12:10 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
io context: fix ref counting
block: make the end_io functions be non-GPL exports
block: fix improper kobject release in blk_integrity_unregister
block: always assign default lock to queues
mg_disk: Add missing ready status check on mg_write()
mg_disk: fix issue with data integrity on error in mg_write()
mg_disk: fix reading invalid status when use polling driver
mg_disk: remove prohibited sleep operation
Linus Torvalds [Fri, 31 Jul 2009 19:09:57 +0000 (12:09 -0700)]
Merge branch 'timers-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: Save mult_orig in clocksource_disable()
Linus Torvalds [Fri, 31 Jul 2009 19:09:22 +0000 (12:09 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: orphan subsystem
imxmmc: Remove unnecessary semicolons
cb710: use SG_MITER_TO_SG/SG_MITER_FROM_SG
sdhci: use SG_MITER_TO_SG/SG_MITER_FROM_SG
lib/scatterlist: add a flags to signalize mapping direction
Linus Torvalds [Fri, 31 Jul 2009 19:09:02 +0000 (12:09 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sound/aoa: Add kmalloc NULL tests
ALSA: hda - Increase PCM stream name buf in patch_realtek.c
sound: mpu401.c: Buffer overflow
sound: aedsp16: Buffer overflow
ALSA: hda: fix out-of-bound hdmi_eld.sad[] write
ALSA: hda - Add quirk for Dell Studio 1555
Magnus Damm [Tue, 28 Jul 2009 21:09:55 +0000 (14:09 -0700)]
clocksource: Save mult_orig in clocksource_disable()
To fix the common case where ->enable() does not set up
mult, make sure mult_orig is saved in mult on disable.
Also add comments to explain why we do this.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: johnstul@us.ibm.com
Cc: lethal@linux-sh.org
Cc: akpm@linux-foundation.org
LKML-Reference: <
20090618152432.10136.9932.sendpatchset@rx1.opensource.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pierre Ossman [Fri, 31 Jul 2009 10:27:28 +0000 (12:27 +0200)]
mmc: orphan subsystem
I do not have the time to take care of this, so remove myself as
maintainer.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Joe Perches [Sun, 28 Jun 2009 16:26:31 +0000 (09:26 -0700)]
imxmmc: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Sebastian Andrzej Siewior [Mon, 22 Jun 2009 07:18:05 +0000 (09:18 +0200)]
cb710: use SG_MITER_TO_SG/SG_MITER_FROM_SG
the code allready uses flush_kernel_dcache_page(). This patch updates the
driver to the recent sg API changes which require that either SG_MITER_TO_SG
or SG_MITER_FROM_SG is set. SG_MITER_TO_SG calls flush_kernel_dcache_page()
in sg_mitter_stop()
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Sebastian Andrzej Siewior [Thu, 18 Jun 2009 07:33:32 +0000 (09:33 +0200)]
sdhci: use SG_MITER_TO_SG/SG_MITER_FROM_SG
so the page will be flushed on unmap on ARCH which need it.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Sebastian Andrzej Siewior [Thu, 18 Jun 2009 08:19:12 +0000 (10:19 +0200)]
lib/scatterlist: add a flags to signalize mapping direction
sg_miter_start() is currently unaware of the direction of the copy
process (to or from the scatter list). It is important to know the
direction because the page has to be flushed in case the data written
is seen on a different mapping in user land on cache incoherent
architectures.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Takashi Iwai [Fri, 31 Jul 2009 08:17:45 +0000 (10:17 +0200)]
Merge branch 'fix/oss' into for-linus
* fix/oss:
sound: mpu401.c: Buffer overflow
sound: aedsp16: Buffer overflow
Takashi Iwai [Fri, 31 Jul 2009 08:17:44 +0000 (10:17 +0200)]
Merge branch 'fix/misc' into for-linus
* fix/misc:
ALSA: sound/aoa: Add kmalloc NULL tests
Takashi Iwai [Fri, 31 Jul 2009 08:17:42 +0000 (10:17 +0200)]
Merge branch 'fix/hda' into for-linus
* fix/hda:
ALSA: hda - Increase PCM stream name buf in patch_realtek.c
ALSA: hda: fix out-of-bound hdmi_eld.sad[] write
ALSA: hda - Add quirk for Dell Studio 1555
Julia Lawall [Fri, 31 Jul 2009 06:32:03 +0000 (08:32 +0200)]
ALSA: sound/aoa: Add kmalloc NULL tests
Check that the result of kzalloc is not NULL before a dereference.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 31 Jul 2009 08:05:11 +0000 (10:05 +0200)]
ALSA: hda - Increase PCM stream name buf in patch_realtek.c
The name buf with size 16 is too short for some codec names, e.g.
truncated like "ALC861-VD Analo". Now the size is doubled.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Li Zefan [Fri, 31 Jul 2009 06:55:48 +0000 (08:55 +0200)]
io context: fix ref counting
Commit
d9c7d394a8ebacb60097b192939ae9f15235225e
("block: prevent possible io_context->refcount overflow") mistakenly
changed atomic_inc(&ioc->nr_tasks) to atomic_long_inc(&ioc->refcount).
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Eric Sandeen [Fri, 31 Jul 2009 05:02:17 +0000 (00:02 -0500)]
xfs: bump up nr_to_write in xfs_vm_writepage
VM calculation for nr_to_write seems off. Bump it way
up, this gets simple streaming writes zippy again.
To be reviewed again after Jens' writeback changes.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Cc: Chris Mason <chris.mason@oracle.com>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Eric Sandeen [Mon, 27 Jul 2009 02:52:01 +0000 (21:52 -0500)]
xfs: reduce bmv_count in xfs_vn_fiemap
commit
6321e3ed2acf3ee9643cdd403e1c88605d7944ba caused
the full bmv_count's worth of getbmapx structures to get
allocated; telling it to do MAXEXTNUM was a bit insane,
resulting in ENOMEM every time.
Chop it down to something reasonable, the number of slots
in the caller's input buffer. If this is too large the
caller may get ENOMEM but the reason should not be a
mystery, and they can try again with something smaller.
We add 1 to the value because in the normal getbmap
world, bmv_count includes the header and xfs_getbmap does:
nex = bmv->bmv_count - 1;
if (nex <= 0)
return XFS_ERROR(EINVAL);
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Linus Torvalds [Thu, 30 Jul 2009 23:46:58 +0000 (16:46 -0700)]
Merge branch 'tracing-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/stat: Fix seqfile memory leak
function-graph: Fix seqfile memory leak
trace_stack: Fix seqfile memory leak
profile: Suppress warning about large allocations when profile=1 is specified
Linus Torvalds [Thu, 30 Jul 2009 23:46:48 +0000 (16:46 -0700)]
Merge git://git./linux/kernel/git/mason/btrfs-unstable
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: be more polite in the async caching threads
Btrfs: preserve commit_root for async caching
Linus Torvalds [Thu, 30 Jul 2009 23:46:31 +0000 (16:46 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: at_hdmac: add DMA slave transfers
dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
dmaengine: dmatest: correct thread_count while using multiple thread per channel
dmaengine: dmatest: add a maximum number of test iterations
drivers/dma: Remove unnecessary semicolons
drivers/dma/fsldma.c: Remove unnecessary semicolons
dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA
fsldma: do not clear bandwidth control bits on the 83xx controller
fsldma: enable external start for the 83xx controller
fsldma: use PCI Read Multiple command
Linus Torvalds [Thu, 30 Jul 2009 23:46:17 +0000 (16:46 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-udf-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
udf: Fix loading of VAT inode when drive wrongly reports number of recorded blocks
Linus Torvalds [Thu, 30 Jul 2009 23:46:06 +0000 (16:46 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-quota-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-quota-2.6:
quota: Silence lockdep on quota_on
Linus Torvalds [Thu, 30 Jul 2009 23:45:53 +0000 (16:45 -0700)]
Merge git://git.infradead.org/users/cbou/battery-2.6.31
* git://git.infradead.org/users/cbou/battery-2.6.31:
Add ds2782 battery gas gauge driver
olpc_battery: Ensure that the TRICKLE bit is checked
olpc_battery: Fix up eeprom read function
Linus Torvalds [Thu, 30 Jul 2009 23:45:37 +0000 (16:45 -0700)]
Merge git://git./linux/kernel/git/steve/gfs2-2.6-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: remove dcache entries for remote deleted inodes
GFS2: Fix incorrent statfs consistency check
GFS2: Don't put unlikely reclaim candidates on the reclaim list.
GFS2: Don't try and dealloc own inode
GFS2: Fix panic in glock memory shrinker
GFS2: keep statfs info in sync on grows
GFS2: Shrink the shrinker
Linus Torvalds [Thu, 30 Jul 2009 23:45:20 +0000 (16:45 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Update defconfigs for embedded 6xx/7xxx, 8xx, 8{3,5,6}xxx
powerpc/86xx: Update GE Fanuc sbc310 default configuration
powerpc/86xx: Update defconfig for GE Fanuc's PPC9A
cpm_uart: Don't use alloc_bootmem in cpm_uart_cpm2.c
powerpc/83xx: Fix PCI IO base address on MPC837xE-RDB boards
powerpc/85xx: Don't scan for TBI PHY addresses on MPC8569E-MDS boards
powerpc/85xx: Fix ethernet link detection on MPC8569E-MDS boards
powerpc/mm: Fix SMP issue with MMU context handling code
Linus Torvalds [Thu, 30 Jul 2009 23:45:03 +0000 (16:45 -0700)]
Merge git://git./linux/kernel/git/rusty/linux-2.6-for-linus
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest and virtio: cleanup struct definitions to Linux style.
lguest: update commentry
lguest: fix comment style
virtio: refactor find_vqs
virtio: delete vq from list
virtio: fix memory leak on device removal
lguest: fix descriptor corruption in example launcher
lguest: dereferencing freed mem in add_eventfd()
Masami Hiramatsu [Tue, 28 Jul 2009 23:47:23 +0000 (19:47 -0400)]
kprobes: Use kernel_text_address() for checking probe address
Use kernel_text_address() for checking probe address instead of
__kernel_text_address(), because __kernel_text_address() returns true
for init functions even after relaseing those functions.
That will hit a BUG() in text_poke().
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 30 Jul 2009 23:40:37 +0000 (16:40 -0700)]
Alan doesn't want to maintain tty code any more
Not that anybody can blame him. It's a morass. But hey, it's way
better than it _used_ to be, though, so thanks for all the fish.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Wed, 22 Jul 2009 16:12:17 +0000 (18:12 +0200)]
quota: Silence lockdep on quota_on
Commit
d01730d74d2b0155da50d44555001706294014f7 didn't completely fix
the problem since we still take dqio_mutex and i_mutex in the wrong
order. Move taking of i_mutex further down (luckily it's needed only
for updating inode flags) below where dqio_mutex is taken.
Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Tue, 14 Jul 2009 17:30:23 +0000 (19:30 +0200)]
udf: Fix loading of VAT inode when drive wrongly reports number of recorded blocks
VAT inode is located in the last block recorded block of the medium. When the
drive errorneously reports number of recorded blocks, we failed to load the VAT
inode and thus mount the medium. This patch makes kernel try to read VAT inode
from the last block of the device if it is different from the last recorded
block.
Signed-off-by: Jan Kara <jack@suse.cz>
Chris Mason [Thu, 30 Jul 2009 14:04:48 +0000 (10:04 -0400)]
Btrfs: be more polite in the async caching threads
The semaphore used by the async caching threads can prevent a
transaction commit, which can make the FS appear to stall. This
releases the semaphore more often when a transaction commit is
in progress.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan Zheng [Thu, 30 Jul 2009 13:40:40 +0000 (09:40 -0400)]
Btrfs: preserve commit_root for async caching
The async block group caching code uses the commit_root pointer
to get a stable version of the extent allocation tree for scanning.
This copy of the tree root isn't going to change and it significantly
reduces the complexity of the scanning code.
During a commit, we have a loop where we update the extent allocation
tree root. We need to loop because updating the root pointer in
the tree of tree roots may allocate blocks which may change the
extent allocation tree.
Right now the commit_root pointer is changed inside this loop. It
is more correct to change the commit_root pointer only after all the
looping is done.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Benjamin Marzinski [Thu, 23 Jul 2009 23:52:34 +0000 (18:52 -0500)]
GFS2: remove dcache entries for remote deleted inodes
When a file is deleted from a gfs2 filesystem on one node, a dcache
entry for it may still exist on other nodes in the cluster. If this
happens, gfs2 will be unable to free this file on disk. Because of this,
it's possible to have a gfs2 filesystem with no files on it and no free
space. With this patch, when a node receives a callback notifying it
that the file is being deleted on another node, it schedules a new
workqueue thread to remove the file's dcache entry.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Benjamin Marzinski [Fri, 10 Jul 2009 23:13:26 +0000 (18:13 -0500)]
GFS2: Fix incorrent statfs consistency check
Since both linked and unlinked inodes are counted by rgd->rd_dinodes, It
makes no sense to count them with the used data blocks (first check that
I changed), it makes sense to count them with the linked inodes (second
check), and it makes no sense to care if there are more unlinked inodes
than linked ones. This fixes these errors.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Benjamin Marzinski [Fri, 10 Jul 2009 23:04:24 +0000 (18:04 -0500)]
GFS2: Don't put unlikely reclaim candidates on the reclaim list.
GFS2 was placing far too many glocks on the reclaim list that were not good
candidates for freeing up from cache. These locks would sit there and
repeatedly get scanned to see if they could be reclaimed, wasting a lot
of time when there was memory pressure. This fix does more checks on the
locks to see if they are actually likely to be removable from cache.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Steven Whitehouse [Fri, 10 Jul 2009 20:13:38 +0000 (21:13 +0100)]
GFS2: Don't try and dealloc own inode
When searching for unlinked, but still allocated inodes during block
allocation, avoid the block relating to the inode that is doing the
allocation. This fixes a hang caused when an unlinked, but still
open, inode tries to allocate some more blocks and lands up
finding itself during the search for deallocatable inodes.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Benjamin Marzinski [Tue, 30 Jun 2009 18:51:11 +0000 (13:51 -0500)]
GFS2: Fix panic in glock memory shrinker
It is possible for gfs2_shrink_glock_memory() to check a glock for
demotion
that's in the process of being freed by gfs2_glock_put(). In this case,
gfs2_shrink_glock_memory() will acquire a new reference to this glock,
and
then try to free the glock itself when it drops the refernce. To solve
this, gfs2_shrink_glock_memory() just needs to check if the glock is in
the process of being freed, and if so skip it without ever unlocking the
lru_lock.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Acked-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Benjamin Marzinski [Thu, 25 Jun 2009 20:09:51 +0000 (15:09 -0500)]
GFS2: keep statfs info in sync on grows
GFS2 wasn't syncing its statfs info on grows. This causes a problem
when you grow the filesystem on multiple nodes. GFS2 would calculate
the new space based on the resource groups (which are always current),
and then assume that the filesystem had grown the from the existing
statfs size. If you grew the filesystem on two different nodes in a
short time, the second node wouldn't see the statfs size change from the
first node, and would assume that it was grown by a larger amount than
it was. When all these changes were synced out, the total fileystem
size would be incorrect (the first grow would be counted twice).
This patch syncs makes GFS2 read in the statfs changes from disk before
a grow, and write them out after the grow, while the master statfs inode
is locked.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Steven Whitehouse [Thu, 25 Jun 2009 15:30:26 +0000 (16:30 +0100)]
GFS2: Shrink the shrinker
This patch removes some of the special cases that the shrinker
was trying to deal with. As a result we leave fewer items on
the list and none at all which cannot be demoted. This makes
the list scanning more efficient and solves some issues seen
with large numbers of inodes.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Rusty Russell [Thu, 30 Jul 2009 22:03:46 +0000 (16:03 -0600)]
lguest and virtio: cleanup struct definitions to Linux style.
I've been doing this for years, and akpm picked me up on it about 12
months ago. lguest partly serves as example code, so let's do it Right.
Also, remove two unused fields in struct vblk_info in the example launcher.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Rusty Russell [Thu, 30 Jul 2009 22:03:45 +0000 (16:03 -0600)]
lguest: update commentry
Every so often, after code shuffles, I need to go through and unbitrot
the Lguest Journey (see drivers/lguest/README). Since we now use RCU in
a simple form in one place I took the opportunity to expand that explanation.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Rusty Russell [Thu, 30 Jul 2009 22:03:45 +0000 (16:03 -0600)]
lguest: fix comment style
I don't really notice it (except to begrudge the extra vertical
space), but Ingo does. And he pointed out that one excuse of lguest
is as a teaching tool, it should set a good example.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Michael S. Tsirkin [Sun, 26 Jul 2009 12:48:08 +0000 (15:48 +0300)]
virtio: refactor find_vqs
This refactors find_vqs, making it more readable and robust, and fixing
two regressions from 2.6.30:
- double free_irq causing BUG_ON on device removal
- probe failure when vq can't be assigned to msi-x vector
(reported on old host kernels)
Tested-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Michael S. Tsirkin [Sun, 26 Jul 2009 12:48:01 +0000 (15:48 +0300)]
virtio: delete vq from list
This makes delete vq the reverse of find vq.
This is required to make it possible to retry find_vqs
after a failure, otherwise the list gets corrupted.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Michael S. Tsirkin [Thu, 23 Jul 2009 11:57:37 +0000 (14:57 +0300)]
virtio: fix memory leak on device removal
Make vp_free_vectors do the reverse of vq_request_vectors.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Thu, 30 Jul 2009 22:03:43 +0000 (16:03 -0600)]
lguest: fix descriptor corruption in example launcher
1d589bb16b825b3a7b4edd34d997f1f1f953033d "Add serial number support
for virtio_blk, V4a" extended 'struct virtio_blk_config' to 536 bytes.
Lguest and S/390 both use an 8 bit value for the feature length, and
this change broke them (if the code is naive).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: John Cooper <john.cooper@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Dan Carpenter [Sun, 19 Jul 2009 11:46:09 +0000 (14:46 +0300)]
lguest: dereferencing freed mem in add_eventfd()
"new" was freed and then dereferenced. Also the return value wasn't being
used so I modified the caller as well.
Compile tested only. Found by smatch (http://repo.or.cz/w/smatch.git).
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Kumar Gala [Thu, 30 Jul 2009 04:34:01 +0000 (23:34 -0500)]
powerpc: Update defconfigs for embedded 6xx/7xxx, 8xx, 8{3,5,6}xxx
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Martyn Welch [Thu, 2 Jul 2009 14:18:44 +0000 (15:18 +0100)]
powerpc/86xx: Update GE Fanuc sbc310 default configuration
General update of defconfig including the following notable changes:
- Enable Highmem support.
- Support for PCMCIA based daughter card.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Martyn Welch [Thu, 2 Jul 2009 14:18:35 +0000 (15:18 +0100)]
powerpc/86xx: Update defconfig for GE Fanuc's PPC9A
General update of defconfig including the following notable changes:
- Enable GPIO access via sysfs on GE Fanuc's PPC9A.
- Enable Highmem support.
- Support for PCMCIA based daughter card.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mark Ware [Mon, 20 Jul 2009 11:51:03 +0000 (21:51 +1000)]
cpm_uart: Don't use alloc_bootmem in cpm_uart_cpm2.c
This is another alloc_bootmem() -> kzalloc() change, this time to
fix the non-fatal badness caused when booting with a cpm2_uart console.
Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Mon, 20 Jul 2009 21:36:43 +0000 (01:36 +0400)]
powerpc/83xx: Fix PCI IO base address on MPC837xE-RDB boards
U-Boot maps PCI IO at 0xe0300000, while current dts files specify
0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y.
8139too Fast Ethernet driver 0.9.28
Machine check in kernel mode.
Caused by (from SRR1=41000): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
MPC837x RDB
[...]
NIP [
00000900] 0x900
LR [
c0439df8] rtl8139_init_board+0x238/0x524
Call Trace:
[
cf831d90] [
c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable)
[
cf831de0] [
c043a15c] rtl8139_init_one+0x78/0x65c
[
cf831e40] [
c0235250] pci_call_probe+0x20/0x30
[...]
This patch fixes the issue by specifying the correct PCI IO base
address.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Wed, 1 Jul 2009 17:39:25 +0000 (21:39 +0400)]
powerpc/85xx: Don't scan for TBI PHY addresses on MPC8569E-MDS boards
Sometimes (e.g. when there are no UEMs attached to a board)
fsl_pq_mdio_find_free() fails to find a spare address for a TBI PHY,
this is because get_phy_id() returns bogus 0x0000ffff values
(0xffffffff is expected), and therefore mdio bus probing fails with
the following message:
fsl-pq_mdio: probe of
e0082120.mdio failed with error -16
And obviously ethernet doesn't work after this.
This patch solves the problem by adding tbi-phy node into mdio node,
so that we won't scan for spare addresses, we'll just use a fixed one.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Wed, 24 Jun 2009 16:30:28 +0000 (20:30 +0400)]
powerpc/85xx: Fix ethernet link detection on MPC8569E-MDS boards
Linux isn't able to detect link changes on ethernet ports that were
used by U-Boot. This is because U-Boot wrongly clears interrupt
polarity bit (INTPOL, 0x400) in the extended status register (EXT_SR,
0x1b) of Marvell PHYs.
There is no easy way for PHY drivers to know IRQ line polarity (we
could extract it from the device tree and pass it to phydevs, but
that'll be quite a lot of work), so for now just reset the PHYs to
their default states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 30 Jul 2009 04:04:25 +0000 (23:04 -0500)]
powerpc/mm: Fix SMP issue with MMU context handling code
In switch_mmu_context() if we call steal_context_smp() to get a context
to use we shouldn't fall through and than call steal_context_up(). Doing
so can be problematic in that the 'mm' that steal_context_up() ends up
using will not get marked dirty in the stale_map[] for other CPUs that
might have used that mm. Thus we could end up with stale TLB entries in
the other CPUs that can cause all kinda of havoc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linus Torvalds [Thu, 30 Jul 2009 02:39:22 +0000 (19:39 -0700)]
Merge branch 'i2c-fixes-rc4' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'i2c-fixes-rc4' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-omap: OMAP3430 Silicon Errata 1.153
i2c-omap: In case of a NACK|ARDY|AL return from the ISR
i2c-omap: Bug in reading the RXSTAT/TXSTAT values from the I2C_BUFFSTAT register
i2c-sh_mobile: change module_init() to subsys_initcall()
i2c: strncpy does not null terminate string
i2c-s3c2410: s3c24xx_i2c_init: don't clobber IICLC value
Linus Torvalds [Thu, 30 Jul 2009 02:15:18 +0000 (19:15 -0700)]
Merge branch 'pm-fixes' of git://git./linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Hibernate: Replace bdget call with simple atomic_inc of i_count
PM / ACPI: HP G7000 Notebook needs a SCI_EN resume quirk
Kristoffer Ericson [Wed, 29 Jul 2009 22:04:32 +0000 (15:04 -0700)]
MAINTAINERS: update HP Jornada 700-series and Epson s1d13xxxfb support
Add the relevant git repositories and affected files to the maintainership
of HP Jornada 700-series and Epson s1d13xxxfb support.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:32 +0000 (15:04 -0700)]
MAINTAINERS: finish off the email address coalescing
Add some touchups to the sample record.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:30 +0000 (15:04 -0700)]
MAINTAINERS: coalesce name and email address lines
Switch the MAINTAINERS email address format from
P: Linus Torvalds
M: torvalds@linux-foundation.org
to
M: Linus Torvalds <torvalds@linux-foundation.org>
Mainly to ease the copy-n-pasting of maitnainer addresses into email clients.
The script to perform this operation:
#! /bin/sh
#
# Change MAINTAINERS from
# P: name
# M: address
# to:
# M: name <address>
#
# Integrate P: and M: lines
#
perl -i -e 'local $/; while(<>) { s@P: ([^\n]+)\nM: ([^\n]+)\n@M: \1 <\2>\n@g; print; }' MAINTAINERS
#
# Quote names with periods, commas and parentheses
#
sed -r -i -e "s/^M: (.+)([\.,'\(])(.*) </M: \"\1\2\3\" </g" MAINTAINERS
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:29 +0000 (15:04 -0700)]
get_maintainerpl-add-git-min-percent-option-fix
Allow an option to control the minimum percentage of sign-offs required
before being considered a maintainer.
git-min-percent has a default value of 5
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:28 +0000 (15:04 -0700)]
get_maintainer.pl: Add git-min-percent option
Allow an option to control the minimum percentage of sign-offs required
before being considered a maintainer.
git-min-percent has a default value of 5
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:28 +0000 (15:04 -0700)]
scripts/get_maintainer.pl: Add -f directory use
Don't require a specific file in a directory to be tested.
Also Arnd Bergmann pointed out that the MAINTAINERS pattern requirement
that directory patterns have a trailing slash was unnecessary and was
likely to be error prone. Removed that requirement.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:27 +0000 (15:04 -0700)]
MAINTAINERS: Scott Murray is no longer with SomaNetworks
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:27 +0000 (15:04 -0700)]
MAINTAINERS: QLOGIC QLA3XXX - Add Ron Mercer email address
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:26 +0000 (15:04 -0700)]
MAINTAINERS: QLOGIC QLA2XXX - add Andrew Vasquez email address
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:26 +0000 (15:04 -0700)]
MAINTAINERS: Remove CS461x sound card section
Thomas Woller's email address bounces
Nils Faerber isn't active
Added Thomas Woller to CREDITS, Nils already has an entry
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:25 +0000 (15:04 -0700)]
MAINTAINERS: INPUT: Add Dmitry's name to his email address
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:25 +0000 (15:04 -0700)]
MAINTAINERS: USB Serial Digi Acceleport: use separate P: for Al Borchers
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:24 +0000 (15:04 -0700)]
MAINTAINERS: Add PPS patterns
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:24 +0000 (15:04 -0700)]
MAINTAINERS: Update KERNEL JANITORS
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:23 +0000 (15:04 -0700)]
MAINTAINERS: Move ARPD to CREDITS
Jonathan Layes is hard to find.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:23 +0000 (15:04 -0700)]
MAINTAINERS: Remove L: linux-kernel@vger.
from sections that should not have them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:22 +0000 (15:04 -0700)]
MAINTAINERS: Use tabs in ACER ASPIRE ONE
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:21 +0000 (15:04 -0700)]
MAINTAINERS: QLGE 10Gb ETHERNET - pair P:/M: entries properly
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:21 +0000 (15:04 -0700)]
MAINTAINERS: Remove ivtv-user lists, add CX18 url
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Wed, 29 Jul 2009 22:04:20 +0000 (15:04 -0700)]
MAINTAINERS: IA64 - pair P:/M: entries properly
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Wed, 29 Jul 2009 22:04:19 +0000 (15:04 -0700)]
uio: mark uio.h functions __KERNEL__ only
To avoid userspace build failures such as:
.../linux/uio.h:37: error: expected `=', `,', `;', `asm' or `__attribute__' before `iov_length'
.../linux/uio.h:47: error: expected declaration specifiers or `...' before `size_t'
move uio functions inside a __KERNEL__ block.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Albin Tonnerre [Wed, 29 Jul 2009 22:04:18 +0000 (15:04 -0700)]
drivers/serial/atmel_serial.c: fix compile when CONFIG_SERIAL_ATMEL=Y and CONFIG_SERIAL_ATMEL_CONSOLE=N
When SERIAL_ATMEL_CONSOLE is disabled, ATMEL_CONSOLE_DEVICE is set to
NULL, and trying to access ATMEL_CONSOLE_DEVICE->flags in
atmel_serial_probe makes the compile fail. This fixes the issue by only
accessing it if CONFIG_SERIAL_ATMEL_CONSOLE is defined
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Wed, 29 Jul 2009 22:04:18 +0000 (15:04 -0700)]
lib: flexible array implementation
Once a structure goes over PAGE_SIZE*2, we see occasional allocation
failures. Some people have chosen to switch over to things like vmalloc()
that will let them keep array-like access to such a large structures.
But, vmalloc() has plenty of downsides.
Here's an alternative. I think it's what Andrew was suggesting here:
http://lkml.org/lkml/2009/7/2/518
I call it a flexible array. It does all of its work in PAGE_SIZE bits, so
never does an order>0 allocation. The base level has
PAGE_SIZE-2*sizeof(int) bytes of storage for pointers to the second level.
So, with a 32-bit arch, you get about 4MB (
4183112 bytes) of total
storage when the objects pack nicely into a page. It is half that on
64-bit because the pointers are twice the size. There's a table detailing
this in the code.
There are kerneldocs for the functions, but here's an
overview:
flex_array_alloc() - dynamically allocate a base structure
flex_array_free() - free the array and all of the
second-level pages
flex_array_free_parts() - free the second-level pages, but
not the base (for static bases)
flex_array_put() - copy into the array at the given index
flex_array_get() - copy out of the array at the given index
flex_array_prealloc() - preallocate the second-level pages
between the given indexes to
guarantee no allocs will occur at
put() time.
We could also potentially just pass the "element_size" into each of the
API functions instead of storing it internally. That would get us one
more base pointer on 32-bit.
I've been testing this by running it in userspace. The header and patch
that I've been using are here, as well as the little script I'm using to
generate the size table which goes in the kerneldocs.
http://sr71.net/~dave/linux/flexarray/
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Wed, 29 Jul 2009 22:04:16 +0000 (15:04 -0700)]
sdhci: get rid of "frequency too high" flood when using eSDHC
Since commit
8dfd0374be84793360db7fff2e635d2cd3bbcb21 ("MMC core: limit
minimum initialization frequency to 400kHz") MMC core checks for minimum
frequency, and that causes following messages flood when using eSDHC
controllers:
...
mmc0: Minimum clock frequency too high for identification mode
mmc0: Minimum clock frequency too high for identification mode
...
The warnings are legitimate, since if we'd use 133 MHz clocks for standard
SDHCI controllers, we'd not able to scale frequency down to 400 kHz.
But eSDHC controllers have a non-standard SD clock management, so we can
divide clock by 256 * 16, not just 256.
This patch introduces get_min_clock() callback for sdhci core and
implements it for sdhci-of driver, and thus fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hidetoshi Seto [Wed, 29 Jul 2009 22:04:14 +0000 (15:04 -0700)]
sysrq, kdump: make sysrq-c consistent
commit
d6580a9f15238b87e618310c862231ae3f352d2d ("kexec: sysrq: simplify
sysrq-c handler") changed the behavior of sysrq-c to unconditional
dereference of NULL pointer. So in cases with CONFIG_KEXEC, where
crash_kexec() was directly called from sysrq-c before, now it can be said
that a step of "real oops" was inserted before starting kdump.
However, in contrast to oops via SysRq-c from keyboard which results in
panic due to in_interrupt(), oops via "echo c > /proc/sysrq-trigger" will
not become panic unless panic_on_oops=1. It means that even if dump is
properly configured to be taken on panic, the sysrq-c from proc interface
might not start crashdump while the sysrq-c from keyboard can start
crashdump. This confuses traditional users of kdump, i.e. people who
expect sysrq-c to do common behavior in both of the keyboard and proc
interface.
This patch brings the keyboard and proc interface behavior of sysrq-c in
line, by forcing panic_on_oops=1 before oops in sysrq-c handler.
And some updates in documentation are included, to clarify that there is
no longer dependency with CONFIG_KEXEC, and that now the system can just
crash by sysrq-c if no dump mechanism is configured.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Brayan Arraes <brayan@yack.com.br>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Jones [Wed, 29 Jul 2009 22:04:12 +0000 (15:04 -0700)]
pps.h needs <linux/types.h>
Found with make headers_check
/usr/include/linux/pps.h:52: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>