OSDN Git Service
Andrea Arcangeli [Fri, 19 Apr 2019 00:50:52 +0000 (17:50 -0700)]
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
commit
04f5866e41fb70690e28397487d8bd8eea7d712a upstream.
The core dumping code has always run without holding the mmap_sem for
writing, despite that is the only way to ensure that the entire vma
layout will not change from under it. Only using some signal
serialization on the processes belonging to the mm is not nearly enough.
This was pointed out earlier. For example in Hugh's post from Jul 2017:
https://lkml.kernel.org/r/alpine.LSU.2.11.
1707191716030.2055@eggly.anvils
"Not strictly relevant here, but a related note: I was very surprised
to discover, only quite recently, how handle_mm_fault() may be called
without down_read(mmap_sem) - when core dumping. That seems a
misguided optimization to me, which would also be nice to correct"
In particular because the growsdown and growsup can move the
vm_start/vm_end the various loops the core dump does around the vma will
not be consistent if page faults can happen concurrently.
Pretty much all users calling mmget_not_zero()/get_task_mm() and then
taking the mmap_sem had the potential to introduce unexpected side
effects in the core dumping code.
Adding mmap_sem for writing around the ->core_dump invocation is a
viable long term fix, but it requires removing all copy user and page
faults and to replace them with get_dump_page() for all binary formats
which is not suitable as a short term fix.
For the time being this solution manually covers the places that can
confuse the core dump either by altering the vma layout or the vma flags
while it runs. Once ->core_dump runs under mmap_sem for writing the
function mmget_still_valid() can be dropped.
Allowing mmap_sem protected sections to run in parallel with the
coredump provides some minor parallelism advantage to the swapoff code
(which seems to be safe enough by never mangling any vma field and can
keep doing swapins in parallel to the core dumping) and to some other
corner case.
In order to facilitate the backporting I added "Fixes:
86039bd3b4e6"
however the side effect of this same race condition in /proc/pid/mem
should be reproducible since before 2.6.12-rc2 so I couldn't add any
other "Fixes:" because there's no hash beyond the git genesis commit.
Because find_extend_vma() is the only location outside of the process
context that could modify the "mm" structures under mmap_sem for
reading, by adding the mmget_still_valid() check to it, all other cases
that take the mmap_sem for reading don't need the new check after
mmget_not_zero()/get_task_mm(). The expand_stack() in page fault
context also doesn't need the new check, because all tasks under core
dumping are frozen.
Link: http://lkml.kernel.org/r/20190325224949.11068-1-aarcange@redhat.com
Fixes:
86039bd3b4e6 ("userfaultfd: add new syscall to provide memory externalization")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Jann Horn <jannh@google.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Jann Horn <jannh@google.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suthikulpanit, Suravee [Wed, 20 Mar 2019 08:12:28 +0000 (08:12 +0000)]
Revert "svm: Fix AVIC incomplete IPI emulation"
commit
4a58038b9e420276157785afa0a0bbb4b9bc2265 upstream.
This reverts commit
bb218fbcfaaa3b115d4cd7a43c0ca164f3a96e57.
As Oren Twaig pointed out the old discussion:
https://patchwork.kernel.org/patch/
8292231/
that the change coud potentially cause an extra IPI to be sent to
the destination vcpu because the AVIC hardware already set the IRR bit
before the incomplete IPI #VMEXIT with id=1 (target vcpu is not running).
Since writting to ICR and ICR2 will also set the IRR. If something triggers
the destination vcpu to get scheduled before the emulation finishes, then
this could result in an additional IPI.
Also, the issue mentioned in the commit
bb218fbcfaaa was misdiagnosed.
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Oren Twaig <oren@scalemp.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Saurav Kashyap [Thu, 18 Apr 2019 10:40:12 +0000 (03:40 -0700)]
Revert "scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO"
commit
0228034d8e5915b98c33db35a98f5e909e848ae9 upstream.
This patch clears FC_RP_STARTED flag during logoff, because of this
re-login(flogi) didn't happen to the switch.
This reverts commit
1550ec458e0cf1a40a170ab1f4c46e3f52860f65.
Fixes:
1550ec458e0c ("scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO")
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Hannes Reinecke <hare@#suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jaesoo Lee [Wed, 10 Apr 2019 00:02:22 +0000 (17:02 -0700)]
scsi: core: set result when the command cannot be dispatched
commit
be549d49115422f846b6d96ee8fd7173a5f7ceb0 upstream.
When SCSI blk-mq is enabled, there is a bug in handling errors in
scsi_queue_rq. Specifically, the bug is not setting result field of
scsi_request correctly when the dispatch of the command has been
failed. Since the upper layer code including the sg_io ioctl expects to
receive any error status from result field of scsi_request, the error is
silently ignored and this could cause data corruptions for some
applications.
Fixes:
d285203cf647 ("scsi: add support for a blk-mq based I/O path.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jaesoo Lee <jalee@purestorage.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mikulas Patocka [Fri, 5 Apr 2019 00:53:28 +0000 (20:53 -0400)]
vt: fix cursor when clearing the screen
commit
b2ecf00631362a83744e5ec249947620db5e240c upstream.
The patch
a6dbe4427559 ("vt: perform safe console erase in the right
order") introduced a bug. The conditional do_update_region() was
replaced by a call to update_region() that does contain the conditional
already, but with unwanted extra side effects such as restoring the cursor
drawing.
In order to reproduce the bug:
- use framebuffer console with the AMDGPU driver
- type "links" to start the console www browser
- press 'q' and space to exit links
Now the cursor will be permanently visible in the center of the
screen. It will stay there until something overwrites it.
The bug goes away if we change update_region() back to the conditional
do_update_region().
[ nico: reworded changelog ]
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Cc: stable@vger.kernel.org
Fixes:
a6dbe4427559 ("vt: perform safe console erase in the right order")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven [Mon, 1 Apr 2019 11:25:10 +0000 (13:25 +0200)]
serial: sh-sci: Fix HSCIF RX sampling point calculation
commit
ace965696da2611af759f0284e26342b7b6cec89 upstream.
There are several issues with the formula used for calculating the
deviation from the intended rate:
1. While min_err and last_stop are signed, srr and baud are unsigned.
Hence the signed values are promoted to unsigned, which will lead
to a bogus value of deviation if min_err is negative,
2. Srr is the register field value, which is one less than the actual
sampling rate factor,
3. The divisions do not use rounding.
Fix this by casting unsigned variables to int, adding one to srr, and
using a single DIV_ROUND_CLOSEST().
Fixes:
63ba1e00f178a448 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven [Fri, 29 Mar 2019 09:10:26 +0000 (10:10 +0100)]
serial: sh-sci: Fix HSCIF RX sampling point adjustment
commit
6b87784b53592a90d21576be8eff688b56d93cce upstream.
The calculation of the sampling point has min() and max() exchanged.
Fix this by using the clamp() helper instead.
Fixes:
63ba1e00f178a448 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KT Liao [Wed, 27 Mar 2019 00:28:32 +0000 (17:28 -0700)]
Input: elan_i2c - add hardware ID for multiple Lenovo laptops
commit
738c06d0e4562e0acf9f2c7438a22b2d5afc67aa upstream.
There are many Lenovo laptops which need elan_i2c support, this patch adds
relevant IDs to the Elan driver so that touchpads are recognized.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 16 Apr 2019 15:06:33 +0000 (17:06 +0200)]
ALSA: core: Fix card races between register and disconnect
commit
2a3f7221acddfe1caa9ff09b3a8158c39b2fdeac upstream.
There is a small race window in the card disconnection code that
allows the registration of another card with the very same card id.
This leads to a warning in procfs creation as caught by syzkaller.
The problem is that we delete snd_cards and snd_cards_lock entries at
the very beginning of the disconnection procedure. This makes the
slot available to be assigned for another card object while the
disconnection procedure is being processed. Then it becomes possible
to issue a procfs registration with the existing file name although we
check the conflict beforehand.
The fix is simply to move the snd_cards and snd_cards_lock clearances
at the end of the disconnection procedure. The references to these
entries are merely either from the global proc files like
/proc/asound/cards or from the card registration / disconnection, so
it should be fine to shift at the very end.
Reported-by: syzbot+48df349490c36f9f54ab@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hui Wang [Wed, 17 Apr 2019 08:10:32 +0000 (16:10 +0800)]
ALSA: hda/realtek - add two more pin configuration sets to quirk table
commit
b26e36b7ef36a8a3a147b1609b2505f8a4ecf511 upstream.
We have two Dell laptops which have the codec
10ec0236 and
10ec0256
respectively, the headset mic on them can't work, need to apply the
quirk of ALC255_FIXUP_DELL1_MIC_NO_PRESENCE. So adding their pin
configurations in the pin quirk table.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Mon, 15 Apr 2019 11:43:02 +0000 (12:43 +0100)]
staging: comedi: ni_usb6501: Fix possible double-free of ->usb_rx_buf
commit
af4b54a2e5ba18259ff9aac445bf546dd60d037e upstream.
`ni6501_alloc_usb_buffers()` is called from `ni6501_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `ni6501_detach()` will be called from the core comedi
module code to clean up. `ni6501_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already beed freed, leading to a
double-free error. Fix it bu removing the call to
`kfree(devpriv->usb_rx_buf)` from `ni6501_alloc_usb_buffers()`, relying
on `ni6501_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Mon, 15 Apr 2019 11:43:01 +0000 (12:43 +0100)]
staging: comedi: ni_usb6501: Fix use of uninitialized mutex
commit
660cf4ce9d0f3497cc7456eaa6d74c8b71d6282c upstream.
If `ni6501_auto_attach()` returns an error, the core comedi module code
will call `ni6501_detach()` to clean up. If `ni6501_auto_attach()`
successfully allocated the comedi device private data, `ni6501_detach()`
assumes that a `struct mutex mut` contained in the private data has been
initialized and uses it. Unfortunately, there are a couple of places
where `ni6501_auto_attach()` can return an error after allocating the
device private data but before initializing the mutex, so this
assumption is invalid. Fix it by initializing the mutex just after
allocating the private data in `ni6501_auto_attach()` before any other
errors can be retturned. Also move the call to `usb_set_intfdata()`
just to keep the code a bit neater (either position for the call is
fine).
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=
cf4f2b6c24aff0a3edf6>:
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
usb 1-1: string descriptor 0 read error: -71
comedi comedi0: Wrong number of endpoints
ni6501 1-1:0.233: driver 'ni6501' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 585 Comm: kworker/0:3 Not tainted
5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xfe/0x12b0 kernel/locking/mutex.c:1072
ni6501_detach+0x5b/0x110 drivers/staging/comedi/drivers/ni_usb6501.c:567
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+cf4f2b6c24aff0a3edf6@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Mon, 15 Apr 2019 11:52:30 +0000 (12:52 +0100)]
staging: comedi: vmk80xx: Fix possible double-free of ->usb_rx_buf
commit
663d294b4768bfd89e529e069bffa544a830b5bf upstream.
`vmk80xx_alloc_usb_buffers()` is called from `vmk80xx_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `vmk80xx_detach()` will be called from the core comedi
module code to clean up. `vmk80xx_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already been freed, leading to a
double-free error. Fix it by removing the call to
`kfree(devpriv->usb_rx_buf)` from `vmk80xx_alloc_usb_buffers()`, relying
on `vmk80xx_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Mon, 15 Apr 2019 11:10:14 +0000 (12:10 +0100)]
staging: comedi: vmk80xx: Fix use of uninitialized semaphore
commit
08b7c2f9208f0e2a32159e4e7a4831b7adb10a3e upstream.
If `vmk80xx_auto_attach()` returns an error, the core comedi module code
will call `vmk80xx_detach()` to clean up. If `vmk80xx_auto_attach()`
successfully allocated the comedi device private data,
`vmk80xx_detach()` assumes that a `struct semaphore limit_sem` contained
in the private data has been initialized and uses it. Unfortunately,
there are a couple of places where `vmk80xx_auto_attach()` can return an
error after allocating the device private data but before initializing
the semaphore, so this assumption is invalid. Fix it by initializing
the semaphore just after allocating the private data in
`vmk80xx_auto_attach()` before any other errors can be returned.
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=
54c2f58f15fe6876b6ad>:
usb 1-1: config 0 has no interface number 0
usb 1-1: New USB device found, idVendor=10cf, idProduct=8068, bcdDevice=e6.8d
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
vmk80xx 1-1:0.117: driver 'vmk80xx' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted
5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152
down+0x12/0x80 kernel/locking/semaphore.c:58
vmk80xx_detach+0x59/0x100 drivers/staging/comedi/drivers/vmk80xx.c:829
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+54c2f58f15fe6876b6ad@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Gromm [Tue, 2 Apr 2019 11:39:57 +0000 (13:39 +0200)]
staging: most: core: use device description as name
commit
131ac62253dba79daf4a6d83ab12293d2b9863d3 upstream.
This patch uses the device description to clearly identity a device
attached to the bus. It is needed as the currently useed mdevX
notation is not sufficiant in case more than one network
interface controller is being used at the same time.
Cc: stable@vger.kernel.org
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
he, bo [Wed, 6 Mar 2019 02:32:20 +0000 (10:32 +0800)]
io: accel: kxcjk1013: restore the range after resume.
commit
fe2d3df639a7940a125a33d6460529b9689c5406 upstream.
On some laptops, kxcjk1013 is powered off when system enters S3. We need
restore the range regiter during resume. Otherwise, the sensor doesn't
work properly after S3.
Signed-off-by: he, bo <bo.he@intel.com>
Signed-off-by: Chen, Hu <hu1.chen@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabrice Gasnier [Mon, 25 Mar 2019 13:01:23 +0000 (14:01 +0100)]
iio: core: fix a possible circular locking dependency
commit
7f75591fc5a123929a29636834d1bcb8b5c9fee3 upstream.
This fixes a possible circular locking dependency detected warning seen
with:
- CONFIG_PROVE_LOCKING=y
- consumer/provider IIO devices (ex: "voltage-divider" consumer of "adc")
When using the IIO consumer interface, e.g. iio_channel_get(), the consumer
device will likely call iio_read_channel_raw() or similar that rely on
'info_exist_lock' mutex.
typically:
...
mutex_lock(&chan->indio_dev->info_exist_lock);
if (chan->indio_dev->info == NULL) {
ret = -ENODEV;
goto err_unlock;
}
ret = do_some_ops()
err_unlock:
mutex_unlock(&chan->indio_dev->info_exist_lock);
return ret;
...
Same mutex is also hold in iio_device_unregister().
The following deadlock warning happens when:
- the consumer device has called an API like iio_read_channel_raw()
at least once.
- the consumer driver is unregistered, removed (unbind from sysfs)
======================================================
WARNING: possible circular locking dependency detected
4.19.24 #577 Not tainted
------------------------------------------------------
sh/372 is trying to acquire lock:
(kn->count#30){++++}, at: kernfs_remove_by_name_ns+0x3c/0x84
but task is already holding lock:
(&dev->info_exist_lock){+.+.}, at: iio_device_unregister+0x18/0x60
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->info_exist_lock){+.+.}:
__mutex_lock+0x70/0xa3c
mutex_lock_nested+0x1c/0x24
iio_read_channel_raw+0x1c/0x60
iio_read_channel_info+0xa8/0xb0
dev_attr_show+0x1c/0x48
sysfs_kf_seq_show+0x84/0xec
seq_read+0x154/0x528
__vfs_read+0x2c/0x15c
vfs_read+0x8c/0x110
ksys_read+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbedefb60
-> #0 (kn->count#30){++++}:
lock_acquire+0xd8/0x268
__kernfs_remove+0x288/0x374
kernfs_remove_by_name_ns+0x3c/0x84
remove_files+0x34/0x78
sysfs_remove_group+0x40/0x9c
sysfs_remove_groups+0x24/0x34
device_remove_attrs+0x38/0x64
device_del+0x11c/0x360
cdev_device_del+0x14/0x2c
iio_device_unregister+0x24/0x60
release_nodes+0x1bc/0x200
device_release_driver_internal+0x1a0/0x230
unbind_store+0x80/0x130
kernfs_fop_write+0x100/0x1e4
__vfs_write+0x2c/0x160
vfs_write+0xa4/0x17c
ksys_write+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbe906840
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->info_exist_lock);
lock(kn->count#30);
lock(&dev->info_exist_lock);
lock(kn->count#30);
*** DEADLOCK ***
...
cdev_device_del() can be called without holding the lock. It should be safe
as info_exist_lock prevents kernelspace consumers to use the exported
routines during/after provider removal. cdev_device_del() is for userspace.
Help to reproduce:
See example: Documentation/devicetree/bindings/iio/afe/voltage-divider.txt
sysv {
compatible = "voltage-divider";
io-channels = <&adc 0>;
output-ohms = <22>;
full-ohms = <222>;
};
First, go to iio:deviceX for the "voltage-divider", do one read:
$ cd /sys/bus/iio/devices/iio:deviceX
$ cat in_voltage0_raw
Then, unbind the consumer driver. It triggers above deadlock warning.
$ cd /sys/bus/platform/drivers/iio-rescale/
$ echo sysv > unbind
Note I don't actually expect stable will pick this up all the
way back into IIO being in staging, but if's probably valid that
far back.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Fixes:
ac917a81117c ("staging:iio:core set the iio_dev.info pointer to null on unregister")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Georg Ottinger [Wed, 30 Jan 2019 13:42:02 +0000 (14:42 +0100)]
iio: adc: at91: disable adc channel interrupt in timeout case
commit
09c6bdee51183a575bf7546890c8c137a75a2b44 upstream.
Having a brief look at at91_adc_read_raw() it is obvious that in the case
of a timeout the setting of AT91_ADC_CHDR and AT91_ADC_IDR registers is
omitted. If 2 different channels are queried we can end up with a
situation where two interrupts are enabled, but only one interrupt is
cleared in the interrupt handler. Resulting in a interrupt loop and a
system hang.
Signed-off-by: Georg Ottinger <g.ottinger@abatec.at>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lars-Peter Clausen [Wed, 20 Feb 2019 15:11:32 +0000 (17:11 +0200)]
iio: Fix scan mask selection
commit
20ea39ef9f2f911bd01c69519e7d69cfec79fde3 upstream.
The trialmask is expected to have all bits set to 0 after allocation.
Currently kmalloc_array() is used which does not zero the memory and so
random bits are set. This results in random channels being enabled when
they shouldn't. Replace kmalloc_array() with kcalloc() which has the same
interface but zeros the memory.
Note the fix is actually required earlier than the below fixes tag, but
will require a manual backport due to move from kmalloc to kmalloc_array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Fixes commit
057ac1acdfc4 ("iio: Use kmalloc_array() in iio_scan_mask_set()").
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jean-Francois Dagenais [Wed, 6 Mar 2019 20:56:06 +0000 (15:56 -0500)]
iio: dac: mcp4725: add missing powerdown bits in store eeprom
commit
06003531502d06bc89d32528f6ec96bf978790f9 upstream.
When issuing the write DAC register and write eeprom command, the two
powerdown bits (PD0 and PD1) are assumed by the chip to be present in
the bytes sent. Leaving them at 0 implies "powerdown disabled" which is
a different state that the current one. By adding the current state of
the powerdown in the i2c write, the chip will correctly power-on exactly
like as it is at the moment of store_eeprom call.
This is documented in MCP4725's datasheet, FIGURE 6-2: "Write Commands
for DAC Input Register and EEPROM" and MCP4726's datasheet, FIGURE 6-3:
"Write All Memory Command".
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dragos Bogdan [Tue, 19 Mar 2019 10:47:00 +0000 (12:47 +0200)]
iio: ad_sigma_delta: select channel when reading register
commit
fccfb9ce70ed4ea7a145f77b86de62e38178517f upstream.
The desired channel has to be selected in order to correctly fill the
buffer with the corresponding data.
The `ad_sd_write_reg()` already does this, but for the
`ad_sd_read_reg_raw()` this was omitted.
Fixes:
af3008485ea03 ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gwendal Grignou [Wed, 13 Mar 2019 11:40:02 +0000 (12:40 +0100)]
iio: cros_ec: Fix the maths for gyro scale calculation
commit
3d02d7082e5823598090530c3988a35f69689943 upstream.
Calculation did not use IIO_DEGREE_TO_RAD and implemented a variant to
avoid precision loss as we aim a nano value. The offset added to avoid
rounding error, though, doesn't give us a close result to the expected
value. E.g.
For 1000dps, the result should be:
(1000 * pi ) / 180 >> 15 ~= 0.
000532632218
But with current calculation we get
$ cat scale
0.
000547890
Fix the calculation by just doing the maths involved for a nano value
val * pi * 10e12 / (180 * 2^15)
so we get a closer result.
$ cat scale
0.
000532632
Fixes:
c14dca07a31d ("iio: cros_ec_sensors: add ChromeOS EC Contiguous Sensors driver")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Looijmans [Wed, 6 Mar 2019 07:31:48 +0000 (08:31 +0100)]
iio:chemical:bme680: Fix SPI read interface
commit
73f3bc6da506711302bb67572440eb84b1ec4a2c upstream.
The SPI interface implementation was completely broken.
When using the SPI interface, there are only 7 address bits, the upper bit
is controlled by a page select register. The core needs access to both
ranges, so implement register read/write for both regions. The regmap
paging functionality didn't agree with a register that needs to be read
and modified, so I implemented a custom paging algorithm.
This fixes that the device wouldn't even probe in SPI mode.
The SPI interface then isn't different from I2C, merged them into the core,
and the I2C/SPI named registers are no longer needed.
Implemented register value caching for the registers to reduce the I2C/SPI
data transfers considerably.
The calibration set reads as all zeroes until some undefined point in time,
and I couldn't determine what makes it valid. The datasheet mentions these
registers but does not provide any hints on when they become valid, and they
aren't even enumerated in the memory map. So check the calibration and
retry reading it from the device after each measurement until it provides
something valid.
Despite the size this is suitable for a stable backport given that
it seems the SPI support never worked.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes:
1b3bd8592780 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Looijmans [Wed, 6 Mar 2019 07:31:47 +0000 (08:31 +0100)]
iio:chemical:bme680: Fix, report temperature in millidegrees
commit
9436f45dd53595e21566a8c6627411077dfdb776 upstream.
The standard unit for temperature is millidegrees Celcius. Adapt the
driver to report in millidegrees instead of degrees.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes:
1b3bd8592780 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Looijmans [Wed, 13 Feb 2019 07:41:47 +0000 (08:41 +0100)]
iio/gyro/bmg160: Use millidegrees for temperature scale
commit
40a7198a4a01037003c7ca714f0d048a61e729ac upstream.
Standard unit for temperature is millidegrees Celcius, whereas this driver
was reporting in degrees. Fix the scale factor in the driver.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sergey Larin [Sat, 2 Mar 2019 16:54:55 +0000 (19:54 +0300)]
iio: gyro: mpu3050: fix chip ID reading
commit
409a51e0a4a5f908763191fae2c29008632eb712 upstream.
According to the datasheet, the last bit of CHIP_ID register controls
I2C bus, and the first one is unused. Handle this correctly.
Note that there are chips out there that have a value such that
the id check currently fails.
Signed-off-by: Sergey Larin <cerg2010cerg2010@mail.ru>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mircea Caprioru [Wed, 20 Feb 2019 11:08:20 +0000 (13:08 +0200)]
staging: iio: ad7192: Fix ad7193 channel address
commit
7ce0f216221856a17fc4934b39284678a5fef2e9 upstream.
This patch fixes the differential channels addresses for the ad7193.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leonard Pollak [Wed, 13 Feb 2019 10:19:52 +0000 (11:19 +0100)]
Staging: iio: meter: fixed typo
commit
0a8a29be499cbb67df79370aaf5109085509feb8 upstream.
This patch fixes an obvious typo, which will cause erroneously returning the Peak
Voltage instead of the Peak Current.
Signed-off-by: Leonard Pollak <leonardp@tr-host.de>
Cc: <Stable@vger.kernel.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vitaly Kuznetsov [Wed, 3 Apr 2019 14:06:42 +0000 (16:06 +0200)]
KVM: x86: svm: make sure NMI is injected after nmi_singlestep
commit
99c221796a810055974b54c02e8f53297e48d146 upstream.
I noticed that apic test from kvm-unit-tests always hangs on my EPYC 7401P,
the hanging test nmi-after-sti is trying to deliver 30000 NMIs and tracing
shows that we're sometimes able to deliver a few but never all.
When we're trying to inject an NMI we may fail to do so immediately for
various reasons, however, we still need to inject it so enable_nmi_window()
arms nmi_singlestep mode. #DB occurs as expected, but we're not checking
for pending NMIs before entering the guest and unless there's a different
event to process, the NMI will never get delivered.
Make KVM_REQ_EVENT request on the vCPU from db_interception() to make sure
pending NMIs are checked and possibly injected.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Tue, 2 Apr 2019 15:10:47 +0000 (08:10 -0700)]
KVM: x86: Don't clear EFER during SMM transitions for 32-bit vCPU
commit
8f4dc2e77cdfaf7e644ef29693fa229db29ee1de upstream.
Neither AMD nor Intel CPUs have an EFER field in the legacy SMRAM save
state area, i.e. don't save/restore EFER across SMM transitions. KVM
somewhat models this, e.g. doesn't clear EFER on entry to SMM if the
guest doesn't support long mode. But during RSM, KVM unconditionally
clears EFER so that it can get back to pure 32-bit mode in order to
start loading CRs with their actual non-SMM values.
Clear EFER only when it will be written when loading the non-SMM state
so as to preserve bits that can theoretically be set on 32-bit vCPUs,
e.g. KVM always emulates EFER_SCE.
And because CR4.PAE is cleared only to play nice with EFER, wrap that
code in the long mode check as well. Note, this may result in a
compiler warning about cr4 being consumed uninitialized. Re-read CR4
even though it's technically unnecessary, as doing so allows for more
readable code and RSM emulation is not a performance critical path.
Fixes:
660a5d517aaab ("KVM: x86: save/load state on SMM switch")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ronnie Sahlberg [Tue, 9 Apr 2019 21:47:22 +0000 (07:47 +1000)]
cifs: fix handle leak in smb2_query_symlink()
commit
e6d0fb7b34f264f72c33053558a360a6a734905e upstream.
If we enter smb2_query_symlink() for something that is not a symlink
and where the SMB2_open() would succeed we would never end up
closing this handle and would thus leak a handle on the server.
Fix this by immediately calling SMB2_close() on successfull open.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZhangXiaoxu [Sat, 6 Apr 2019 07:47:39 +0000 (15:47 +0800)]
cifs: Fix use-after-free in SMB2_read
commit
088aaf17aa79300cab14dbee2569c58cfafd7d6e upstream.
There is a KASAN use-after-free:
BUG: KASAN: use-after-free in SMB2_read+0x1136/0x1190
Read of size 8 at addr
ffff8880b4e45e50 by task ln/1009
Should not release the 'req' because it will use in the trace.
Fixes:
eccb4422cf97 ("smb3: Add ftrace tracepoints for improved SMB3 debugging")
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org> 4.18+
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZhangXiaoxu [Sat, 6 Apr 2019 07:47:38 +0000 (15:47 +0800)]
cifs: Fix use-after-free in SMB2_write
commit
6a3eb3360667170988f8a6477f6686242061488a upstream.
There is a KASAN use-after-free:
BUG: KASAN: use-after-free in SMB2_write+0x1342/0x1580
Read of size 8 at addr
ffff8880b6a8e450 by task ln/4196
Should not release the 'req' because it will use in the trace.
Fixes:
eccb4422cf97 ("smb3: Add ftrace tracepoints for improved SMB3 debugging")
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org> 4.18+
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aurelien Aptel [Fri, 29 Mar 2019 09:49:12 +0000 (10:49 +0100)]
CIFS: keep FileInfo handle live during oplock break
commit
b98749cac4a695f084a5ff076f4510b23e353ecd upstream.
In the oplock break handler, writing pending changes from pages puts
the FileInfo handle. If the refcount reaches zero it closes the handle
and waits for any oplock break handler to return, thus causing a deadlock.
To prevent this situation:
* We add a wait flag to cifsFileInfo_put() to decide whether we should
wait for running/pending oplock break handlers
* We keep an additionnal reference of the SMB FileInfo handle so that
for the rest of the handler putting the handle won't close it.
- The ref is bumped everytime we queue the handler via the
cifs_queue_oplock_break() helper.
- The ref is decremented at the end of the handler
This bug was triggered by xfstest 464.
Also important fix to address the various reports of
oops in smb2_push_mandatory_locks
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Oskolkov [Tue, 23 Apr 2019 17:25:33 +0000 (10:25 -0700)]
net: IP6 defrag: use rbtrees in nf_conntrack_reasm.c
[ Upstream commit
997dd96471641e147cb2c33ad54284000d0f5e35 ]
Currently, IPv6 defragmentation code drops non-last fragments that
are smaller than 1280 bytes: see
commit
0ed4229b08c1 ("ipv6: defrag: drop non-last frags smaller than min mtu")
This behavior is not specified in IPv6 RFCs and appears to break
compatibility with some IPv6 implemenations, as reported here:
https://www.spinics.net/lists/netdev/msg543846.html
This patch re-uses common IP defragmentation queueing and reassembly
code in IP6 defragmentation in nf_conntrack, removing the 1280 byte
restriction.
Signed-off-by: Peter Oskolkov <posk@google.com>
Reported-by: Tom Herbert <tom@herbertland.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Peter Oskolkov [Tue, 23 Apr 2019 17:25:32 +0000 (10:25 -0700)]
net: IP6 defrag: use rbtrees for IPv6 defrag
[ Upstream commit
d4289fcc9b16b89619ee1c54f829e05e56de8b9a ]
Currently, IPv6 defragmentation code drops non-last fragments that
are smaller than 1280 bytes: see
commit
0ed4229b08c1 ("ipv6: defrag: drop non-last frags smaller than min mtu")
This behavior is not specified in IPv6 RFCs and appears to break
compatibility with some IPv6 implemenations, as reported here:
https://www.spinics.net/lists/netdev/msg543846.html
This patch re-uses common IP defragmentation queueing and reassembly
code in IPv6, removing the 1280 byte restriction.
v2: change handling of overlaps to match that of upstream.
Signed-off-by: Peter Oskolkov <posk@google.com>
Reported-by: Tom Herbert <tom@herbertland.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Peter Oskolkov [Tue, 23 Apr 2019 17:25:31 +0000 (10:25 -0700)]
net: IP defrag: encapsulate rbtree defrag code into callable functions
[ Upstream commit
c23f35d19db3b36ffb9e04b08f1d91565d15f84f ]
This is a refactoring patch: without changing runtime behavior,
it moves rbtree-related code from IPv4-specific files/functions
into .h/.c defrag files shared with IPv6 defragmentation code.
v2: make handling of overlapping packets match upstream.
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Toke Høiland-Jørgensen [Fri, 5 Apr 2019 13:01:59 +0000 (15:01 +0200)]
sch_cake: Simplify logic in cake_select_tin()
[ Upstream commit
4976e3c683f328bc6f2edef555a4ffee6524486f ]
The logic in cake_select_tin() was getting a bit hairy, and it turns out we
can simplify it quite a bit. This also allows us to get rid of one of the
two diffserv parsing functions, which has the added benefit that
already-zeroed DSCP fields won't get re-written.
Suggested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pieter Jansen van Vuuren [Tue, 2 Apr 2019 02:36:34 +0000 (19:36 -0700)]
nfp: flower: remove vlan CFI bit from push vlan action
[ Upstream commit
42cd5484a22f1a1b947e21e2af65fa7dab09d017 ]
We no longer set CFI when pushing vlan tags, therefore we remove
the CFI bit from push vlan.
Fixes:
1a1e586f54bf ("nfp: add basic action capabilities to flower offloads")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pieter Jansen van Vuuren [Tue, 2 Apr 2019 02:36:33 +0000 (19:36 -0700)]
nfp: flower: replace CFI with vlan present
[ Upstream commit
f7ee799a51ddbcc205ef615fe424fb5084e9e0aa ]
Replace vlan CFI bit with a vlan present bit that indicates the
presence of a vlan tag. Previously the driver incorrectly assumed
that an vlan id of 0 is not matchable, therefore we indicate vlan
presence with a vlan present bit.
Fixes:
5571e8c9f241 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Toke Høiland-Jørgensen [Thu, 4 Apr 2019 13:01:33 +0000 (15:01 +0200)]
sch_cake: Make sure we can write the IP header before changing DSCP bits
[ Upstream commit
c87b4ecdbe8db27867a7b7f840291cd843406bd7 ]
There is not actually any guarantee that the IP headers are valid before we
access the DSCP bits of the packets. Fix this using the same approach taken
in sch_dsmark.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Toke Høiland-Jørgensen [Thu, 4 Apr 2019 13:01:33 +0000 (15:01 +0200)]
sch_cake: Use tc_skb_protocol() helper for getting packet protocol
[ Upstream commit
b2100cc56fca8c51d28aa42a9f1fbcb2cf351996 ]
We shouldn't be using skb->protocol directly as that will miss cases with
hardware-accelerated VLAN tags. Use the helper instead to get the right
protocol number.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Lemon [Sun, 14 Apr 2019 21:21:29 +0000 (14:21 -0700)]
route: Avoid crash from dereferencing NULL rt->from
[ Upstream commit
9c69a13205151c0d801de9f9d83a818e6e8f60ec ]
When __ip6_rt_update_pmtu() is called, rt->from is RCU dereferenced, but is
never checked for null - rt6_flush_exceptions() may have removed the entry.
[ 1913.989004] RIP: 0010:ip6_rt_cache_alloc+0x13/0x170
[ 1914.209410] Call Trace:
[ 1914.214798] <IRQ>
[ 1914.219226] __ip6_rt_update_pmtu+0xb0/0x190
[ 1914.228649] ip6_tnl_xmit+0x2c2/0x970 [ip6_tunnel]
[ 1914.239223] ? ip6_tnl_parse_tlv_enc_lim+0x32/0x1a0 [ip6_tunnel]
[ 1914.252489] ? __gre6_xmit+0x148/0x530 [ip6_gre]
[ 1914.262678] ip6gre_tunnel_xmit+0x17e/0x3c7 [ip6_gre]
[ 1914.273831] dev_hard_start_xmit+0x8d/0x1f0
[ 1914.283061] sch_direct_xmit+0xfa/0x230
[ 1914.291521] __qdisc_run+0x154/0x4b0
[ 1914.299407] net_tx_action+0x10e/0x1f0
[ 1914.307678] __do_softirq+0xca/0x297
[ 1914.315567] irq_exit+0x96/0xa0
[ 1914.322494] smp_apic_timer_interrupt+0x68/0x130
[ 1914.332683] apic_timer_interrupt+0xf/0x20
[ 1914.341721] </IRQ>
Fixes:
a68886a69180 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Saeed Mahameed [Tue, 19 Mar 2019 08:05:41 +0000 (01:05 -0700)]
net/mlx5: FPGA, tls, idr remove on flow delete
[ Upstream commit
df3a8344d404a810b4aadbf19b08c8232fbaa715 ]
Flow is kfreed on mlx5_fpga_tls_del_flow but kept in the idr data
structure, this is risky and can cause use-after-free, since the
idr_remove is delayed until tls_send_teardown_cmd completion.
Instead of delaying idr_remove, in this patch we do it on
mlx5_fpga_tls_del_flow, before actually kfree(flow).
Added synchronize_rcu before kfree(flow)
Fixes:
ab412e1dd7db ("net/mlx5: Accel, add TLS rx offload routines")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jakub Kicinski [Tue, 9 Apr 2019 00:59:50 +0000 (17:59 -0700)]
net/tls: prevent bad memory access in tls_is_sk_tx_device_offloaded()
[ Upstream commit
b4f47f3848eb70986f75d06112af7b48b7f5f462 ]
Unlike '&&' operator, the '&' does not have short-circuit
evaluation semantics. IOW both sides of the operator always
get evaluated. Fix the wrong operator in
tls_is_sk_tx_device_offloaded(), which would lead to
out-of-bounds access for for non-full sockets.
Fixes:
4799ac81e52a ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Saeed Mahameed [Wed, 20 Mar 2019 05:09:05 +0000 (22:09 -0700)]
net/mlx5: FPGA, tls, hold rcu read lock a bit longer
[ Upstream commit
31634bf5dcc418b5b2cacd954394c0c4620db6a2 ]
To avoid use-after-free, hold the rcu read lock until we are done copying
flow data into the command buffer.
Fixes:
ab412e1dd7db ("net/mlx5: Accel, add TLS rx offload routines")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matteo Croce [Thu, 11 Apr 2019 10:26:33 +0000 (12:26 +0200)]
net: thunderx: don't allow jumbo frames with XDP
[ Upstream commit
1f227d16083b2e280b7dde4ca78883d75593f2fd ]
The thunderx driver forbids to load an eBPF program if the MTU is too high,
but this can be circumvented by loading the eBPF, then raising the MTU.
Fix this by limiting the MTU if an eBPF program is already loaded.
Fixes:
05c773f52b96e ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matteo Croce [Thu, 11 Apr 2019 10:26:32 +0000 (12:26 +0200)]
net: thunderx: raise XDP MTU to 1508
[ Upstream commit
5ee15c101f29e0093ffb5448773ccbc786eb313b ]
The thunderx driver splits frames bigger than 1530 bytes to multiple
pages, making impossible to run an eBPF program on it.
This leads to a maximum MTU of 1508 if QinQ is in use.
The thunderx driver forbids to load an eBPF program if the MTU is higher
than 1500 bytes. Raise the limit to 1508 so it is possible to use L2
protocols which need some more headroom.
Fixes:
05c773f52b96e ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Sun, 14 Apr 2019 00:32:21 +0000 (17:32 -0700)]
ipv4: ensure rcu_read_lock() in ipv4_link_failure()
[ Upstream commit
c543cb4a5f07e09237ec0fc2c60c9f131b2c79ad ]
fib_compute_spec_dst() needs to be called under rcu protection.
syzbot reported :
WARNING: suspicious RCU usage
5.1.0-rc4+ #165 Not tainted
include/linux/inetdevice.h:220 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by swapper/0/0:
#0:
0000000051b67925 ((&n->timer)){+.-.}, at: lockdep_copy_map include/linux/lockdep.h:170 [inline]
#0:
0000000051b67925 ((&n->timer)){+.-.}, at: call_timer_fn+0xda/0x720 kernel/time/timer.c:1315
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.1.0-rc4+ #165
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
lockdep_rcu_suspicious+0x153/0x15d kernel/locking/lockdep.c:5162
__in_dev_get_rcu include/linux/inetdevice.h:220 [inline]
fib_compute_spec_dst+0xbbd/0x1030 net/ipv4/fib_frontend.c:294
spec_dst_fill net/ipv4/ip_options.c:245 [inline]
__ip_options_compile+0x15a7/0x1a10 net/ipv4/ip_options.c:343
ipv4_link_failure+0x172/0x400 net/ipv4/route.c:1195
dst_link_failure include/net/dst.h:427 [inline]
arp_error_report+0xd1/0x1c0 net/ipv4/arp.c:297
neigh_invalidate+0x24b/0x570 net/core/neighbour.c:995
neigh_timer_handler+0xc35/0xf30 net/core/neighbour.c:1081
call_timer_fn+0x190/0x720 kernel/time/timer.c:1325
expire_timers kernel/time/timer.c:1362 [inline]
__run_timers kernel/time/timer.c:1681 [inline]
__run_timers kernel/time/timer.c:1649 [inline]
run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694
__do_softirq+0x266/0x95a kernel/softirq.c:293
invoke_softirq kernel/softirq.c:374 [inline]
irq_exit+0x180/0x1d0 kernel/softirq.c:414
exiting_irq arch/x86/include/asm/apic.h:536 [inline]
smp_apic_timer_interrupt+0x14a/0x570 arch/x86/kernel/apic/apic.c:1062
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807
Fixes:
ed0de45a1008 ("ipv4: recompile ip options in ipv4_link_failure")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Suryaputra [Fri, 12 Apr 2019 20:19:27 +0000 (16:19 -0400)]
ipv4: recompile ip options in ipv4_link_failure
[ Upstream commit
ed0de45a1008991fdaa27a0152befcb74d126a8b ]
Recompile IP options since IPCB may not be valid anymore when
ipv4_link_failure is called from arp_error_report.
Refer to the commit
3da1ed7ac398 ("net: avoid use IPCB in cipso_v4_error")
and the commit before that (
9ef6b42ad6fd) for a similar issue.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason Wang [Tue, 9 Apr 2019 04:10:25 +0000 (12:10 +0800)]
vhost: reject zero size iova range
[ Upstream commit
813dbeb656d6c90266f251d8bd2b02d445afa63f ]
We used to accept zero size iova range which will lead a infinite loop
in translate_desc(). Fixing this by failing the request in this case.
Reported-by: syzbot+d21e6e297322a900c128@syzkaller.appspotmail.com
Fixes:
6b1e6cc7 ("vhost: new device IOTLB API")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hoang Le [Tue, 9 Apr 2019 07:59:24 +0000 (14:59 +0700)]
tipc: missing entries in name table of publications
[ Upstream commit
d1841533e54876f152a30ac398a34f47ad6590b1 ]
When binding multiple services with specific type 1Ki, 2Ki..,
this leads to some entries in the name table of publications
missing when listed out via 'tipc name show'.
The problem is at identify zero last_type conditional provided
via netlink. The first is initial 'type' when starting name table
dummping. The second is continuously with zero type (node state
service type). Then, lookup function failure to finding node state
service type in next iteration.
To solve this, adding more conditional to marked as dirty type and
lookup correct service type for the next iteration instead of select
the first service as initial 'type' zero.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hangbin Liu [Mon, 8 Apr 2019 08:45:17 +0000 (16:45 +0800)]
team: set slave to promisc if team is already in promisc mode
[ Upstream commit
43c2adb9df7ddd6560fd3546d925b42cef92daa0 ]
After adding a team interface to bridge, the team interface will enter
promisc mode. Then if we add a new slave to team0, the slave will keep
promisc off. Fix it by setting slave to promisc on if team master is
already in promisc mode, also do the same for allmulti.
v2: add promisc and allmulti checking when delete ports
Fixes:
3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 16 Apr 2019 17:55:20 +0000 (10:55 -0700)]
tcp: tcp_grow_window() needs to respect tcp_space()
[ Upstream commit
50ce163a72d817a99e8974222dcf2886d5deb1ae ]
For some reason, tcp_grow_window() correctly tests if enough room
is present before attempting to increase tp->rcv_ssthresh,
but does not prevent it to grow past tcp_space()
This is causing hard to debug issues, like failing
the (__tcp_select_window(sk) >= tp->rcv_wnd) test
in __tcp_ack_snd_check(), causing ACK delays and possibly
slow flows.
Depending on tcp_rmem[2], MTU, skb->len/skb->truesize ratio,
we can see the problem happening on "netperf -t TCP_RR -- -r 2000,2000"
after about 60 round trips, when the active side no longer sends
immediate acks.
This bug predates git history.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lorenzo Bianconi [Tue, 9 Apr 2019 09:47:20 +0000 (11:47 +0200)]
net: fou: do not use guehdr after iptunnel_pull_offloads in gue_udp_recv
[ Upstream commit
988dc4a9a3b66be75b30405a5494faf0dc7cffb6 ]
gue tunnels run iptunnel_pull_offloads on received skbs. This can
determine a possible use-after-free accessing guehdr pointer since
the packet will be 'uncloned' running pskb_expand_head if it is a
cloned gso skb (e.g if the packet has been sent though a veth device)
Fixes:
a09a4c8dd1ec ("tunnels: Remove encapsulation offloads on decap")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yuya Kusakabe [Tue, 16 Apr 2019 01:22:28 +0000 (10:22 +0900)]
net: Fix missing meta data in skb with vlan packet
[ Upstream commit
d85e8be2a5a02869f815dd0ac2d743deb4cd7957 ]
skb_reorder_vlan_header() should move XDP meta data with ethernet header
if XDP meta data exists.
Fixes:
de8f3a83b0a0 ("bpf: add meta pointer for direct access")
Signed-off-by: Yuya Kusakabe <yuya.kusakabe@gmail.com>
Signed-off-by: Takeru Hayasaka <taketarou2@gmail.com>
Co-developed-by: Takeru Hayasaka <taketarou2@gmail.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikolay Aleksandrov [Thu, 11 Apr 2019 12:08:25 +0000 (15:08 +0300)]
net: bridge: multicast: use rcu to access port list from br_multicast_start_querier
[ Upstream commit
c5b493ce192bd7a4e7bd073b5685aad121eeef82 ]
br_multicast_start_querier() walks over the port list but it can be
called from a timer with only multicast_lock held which doesn't protect
the port list, so use RCU to walk over it.
Fixes:
c83b8fab06fc ("bridge: Restart queries when last querier expires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikolay Aleksandrov [Thu, 11 Apr 2019 10:56:39 +0000 (13:56 +0300)]
net: bridge: fix per-port af_packet sockets
[ Upstream commit
3b2e2904deb314cc77a2192f506f2fd44e3d10d0 ]
When the commit below was introduced it changed two visible things:
- the skb was no longer passed through the protocol handlers with the
original device
- the skb was passed up the stack with skb->dev = bridge
The first change broke af_packet sockets on bridge ports. For example we
use them for hostapd which listens for ETH_P_PAE packets on the ports.
We discussed two possible fixes:
- create a clone and pass it through NF_HOOK(), act on the original skb
based on the result
- somehow signal to the caller from the okfn() that it was called,
meaning the skb is ok to be passed, which this patch is trying to
implement via returning 1 from the bridge link-local okfn()
Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and
drop/error would return < 0 thus the okfn() is called only when the
return was 1, so we signal to the caller that it was called by preserving
the return value from nf_hook().
Fixes:
8626c56c8279 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Mon, 15 Apr 2019 20:57:23 +0000 (15:57 -0500)]
net: atm: Fix potential Spectre v1 vulnerabilities
[ Upstream commit
899537b73557aafbdd11050b501cf54b4f5c45af ]
arg is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/atm/lec.c:715 lec_mcast_attach() warn: potential spectre issue 'dev_lec' [r] (local cap)
Fix this by sanitizing arg before using it to index dev_lec.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/
20180423164740.GY17484@dhcp22.suse.cz/
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Si-Wei Liu [Mon, 8 Apr 2019 23:45:27 +0000 (19:45 -0400)]
failover: allow name change on IFF_UP slave interfaces
[ Upstream commit
8065a779f17e94536a1c4dcee4f9d88011672f97 ]
When a netdev appears through hot plug then gets enslaved by a failover
master that is already up and running, the slave will be opened
right away after getting enslaved. Today there's a race that userspace
(udev) may fail to rename the slave if the kernel (net_failover)
opens the slave earlier than when the userspace rename happens.
Unlike bond or team, the primary slave of failover can't be renamed by
userspace ahead of time, since the kernel initiated auto-enslavement is
unable to, or rather, is never meant to be synchronized with the rename
request from userspace.
As the failover slave interfaces are not designed to be operated
directly by userspace apps: IP configuration, filter rules with
regard to network traffic passing and etc., should all be done on master
interface. In general, userspace apps only care about the
name of master interface, while slave names are less important as long
as admin users can see reliable names that may carry
other information describing the netdev. For e.g., they can infer that
"ens3nsby" is a standby slave of "ens3", while for a
name like "eth0" they can't tell which master it belongs to.
Historically the name of IFF_UP interface can't be changed because
there might be admin script or management software that is already
relying on such behavior and assumes that the slave name can't be
changed once UP. But failover is special: with the in-kernel
auto-enslavement mechanism, the userspace expectation for device
enumeration and bring-up order is already broken. Previously initramfs
and various userspace config tools were modified to bypass failover
slaves because of auto-enslavement and duplicate MAC address. Similarly,
in case that users care about seeing reliable slave name, the new type
of failover slaves needs to be taken care of specifically in userspace
anyway.
It's less risky to lift up the rename restriction on failover slave
which is already UP. Although it's possible this change may potentially
break userspace component (most likely configuration scripts or
management software) that assumes slave name can't be changed while
UP, it's relatively a limited and controllable set among all userspace
components, which can be fixed specifically to listen for the rename
events on failover slaves. Userspace component interacting with slaves
is expected to be changed to operate on failover master interface
instead, as the failover slave is dynamic in nature which may come and
go at any point. The goal is to make the role of failover slaves less
relevant, and userspace components should only deal with failover master
in the long run.
Fixes:
30c8bd5aa8b2 ("net: Introduce generic failover module")
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sabrina Dubroca [Fri, 12 Apr 2019 13:04:10 +0000 (15:04 +0200)]
bonding: fix event handling for stacked bonds
[ Upstream commit
92480b3977fd3884649d404cbbaf839b70035699 ]
When a bond is enslaved to another bond, bond_netdev_event() only
handles the event as if the bond is a master, and skips treating the
bond as a slave.
This leads to a refcount leak on the slave, since we don't remove the
adjacency to its master and the master holds a reference on the slave.
Reproducer:
ip link add bondL type bond
ip link add bondU type bond
ip link set bondL master bondU
ip link del bondL
No "Fixes:" tag, this code is older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 20 Apr 2019 07:16:05 +0000 (09:16 +0200)]
Linux 4.19.36
Arnd Bergmann [Wed, 6 Mar 2019 10:52:36 +0000 (11:52 +0100)]
appletalk: Fix compile regression
[ Upstream commit
27da0d2ef998e222a876c0cec72aa7829a626266 ]
A bugfix just broke compilation of appletalk when CONFIG_SYSCTL
is disabled:
In file included from net/appletalk/ddp.c:65:
net/appletalk/ddp.c: In function 'atalk_init':
include/linux/atalk.h:164:34: error: expected expression before 'do'
#define atalk_register_sysctl() do { } while(0)
^~
net/appletalk/ddp.c:1934:7: note: in expansion of macro 'atalk_register_sysctl'
rc = atalk_register_sysctl();
This is easier to avoid by using conventional inline functions
as stubs rather than macros. The header already has inline
functions for other purposes, so I'm changing over all the
macros for consistency.
Fixes:
6377f787aeb9 ("appletalk: Fix use-after-free in atalk_proc_exit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Konstantin Khlebnikov [Tue, 9 Apr 2019 17:05:43 +0000 (20:05 +0300)]
mm: hide incomplete nr_indirectly_reclaimable in sysfs
In upstream branch this fixed by commit
b29940c1abd7 ("mm: rename and
change semantics of nr_indirectly_reclaimable_bytes").
This fixes /sys/devices/system/node/node*/vmstat format:
...
nr_dirtied
6613155
nr_written
5796802
11089216
...
Cc: <stable@vger.kernel.org> # 4.19.y
Fixes:
7aaf77272358 ("mm: don't show nr_indirectly_reclaimable in /proc/vmstat")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Roman Gushchin <guro@fb.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Gushchin [Tue, 30 Oct 2018 17:48:25 +0000 (17:48 +0000)]
mm: hide incomplete nr_indirectly_reclaimable in /proc/zoneinfo
[fixed differently upstream, this is a work-around to resolve it for 4.19.y]
Yongqin reported that /proc/zoneinfo format is broken in 4.14
due to commit
7aaf77272358 ("mm: don't show nr_indirectly_reclaimable
in /proc/vmstat")
Node 0, zone DMA
per-node stats
nr_inactive_anon 403
nr_active_anon 89123
nr_inactive_file 128887
nr_active_file 47377
nr_unevictable 2053
nr_slab_reclaimable 7510
nr_slab_unreclaimable 10775
nr_isolated_anon 0
nr_isolated_file 0
<...>
nr_vmscan_write 0
nr_vmscan_immediate_reclaim 0
nr_dirtied 6022
nr_written 5985
74240
^^^^^^^^^^
pages free 131656
The problem is caused by the nr_indirectly_reclaimable counter,
which is hidden from the /proc/vmstat, but not from the
/proc/zoneinfo. Let's fix this inconsistency and hide the
counter from /proc/zoneinfo exactly as from /proc/vmstat.
BTW, in 4.19+ the counter has been renamed and exported by
the commit
b29940c1abd7 ("mm: rename and change semantics of
nr_indirectly_reclaimable_bytes"), so there is no such a problem
anymore.
Cc: <stable@vger.kernel.org> # 4.14.x-4.18.x
Fixes:
7aaf77272358 ("mm: don't show nr_indirectly_reclaimable in /proc/vmstat")
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kaike Wan [Mon, 18 Mar 2019 16:55:19 +0000 (09:55 -0700)]
IB/hfi1: Failed to drain send queue when QP is put into error state
commit
662d66466637862ef955f7f6e78a286d8cf0ebef upstream.
When a QP is put into error state, all pending requests in the send work
queue should be drained. The following sequence of events could lead to a
failure, causing a request to hang:
(1) The QP builds a packet and tries to send through SDMA engine.
However, PIO engine is still busy. Consequently, this packet is put on
the QP's tx list and the QP is put on the PIO waiting list. The field
qp->s_flags is set with HFI1_S_WAIT_PIO_DRAIN;
(2) The QP is put into error state by the user application and
notify_error_qp() is called, which removes the QP from the PIO waiting
list and the packet from the QP's tx list. In addition, qp->s_flags is
cleared of RVT_S_ANY_WAIT_IO bits, which does not include
HFI1_S_WAIT_PIO_DRAIN bit;
(3) The hfi1_schdule_send() function is called to drain the QP's send
queue. Subsequently, hfi1_do_send() is called. Since the flag bit
HFI1_S_WAIT_PIO_DRAIN is set in qp->s_flags, hfi1_send_ok() fails. As
a result, hfi1_do_send() bails out without draining any request from
the send queue;
(4) The PIO engine completes the sending and tries to wake up any QP on
its waiting list. But the QP has been removed from the PIO waiting
list and therefore is kept in sleep forever.
The fix is to clear qp->s_flags of HFI1_S_ANY_WAIT_IO bits in step (2).
HFI1_S_ANY_WAIT_IO includes RVT_S_ANY_WAIT_IO and HFI1_S_WAIT_PIO_DRAIN.
Fixes:
2e2ba09e48b7 ("IB/rdmavt, IB/hfi1: Create device dependent s_flags")
Cc: <stable@vger.kernel.org> # 4.19.x+
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Mon, 25 Mar 2019 14:54:43 +0000 (15:54 +0100)]
bpf: fix use after free in bpf_evict_inode
[ Upstream commit
1da6c4d9140cb7c13e87667dc4e1488d6c8fc10f ]
syzkaller was able to generate the following UAF in bpf:
BUG: KASAN: use-after-free in lookup_last fs/namei.c:2269 [inline]
BUG: KASAN: use-after-free in path_lookupat.isra.43+0x9f8/0xc00 fs/namei.c:2318
Read of size 1 at addr
ffff8801c4865c47 by task syz-executor2/9423
CPU: 0 PID: 9423 Comm: syz-executor2 Not tainted 4.20.0-rc1-next-
20181109+
#110
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.8+0x242/0x309 mm/kasan/report.c:412
__asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:430
lookup_last fs/namei.c:2269 [inline]
path_lookupat.isra.43+0x9f8/0xc00 fs/namei.c:2318
filename_lookup+0x26a/0x520 fs/namei.c:2348
user_path_at_empty+0x40/0x50 fs/namei.c:2608
user_path include/linux/namei.h:62 [inline]
do_mount+0x180/0x1ff0 fs/namespace.c:2980
ksys_mount+0x12d/0x140 fs/namespace.c:3258
__do_sys_mount fs/namespace.c:3272 [inline]
__se_sys_mount fs/namespace.c:3269 [inline]
__x64_sys_mount+0xbe/0x150 fs/namespace.c:3269
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457569
Code: fd b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7
48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff
ff 0f 83 cb b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007fde6ed96c78 EFLAGS:
00000246 ORIG_RAX:
00000000000000a5
RAX:
ffffffffffffffda RBX:
0000000000000005 RCX:
0000000000457569
RDX:
0000000020000040 RSI:
0000000020000000 RDI:
0000000000000000
RBP:
000000000072bf00 R08:
0000000020000340 R09:
0000000000000000
R10:
0000000000200000 R11:
0000000000000246 R12:
00007fde6ed976d4
R13:
00000000004c2c24 R14:
00000000004d4990 R15:
00000000ffffffff
Allocated by task 9424:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xc7/0xe0 mm/kasan/kasan.c:553
__do_kmalloc mm/slab.c:3722 [inline]
__kmalloc_track_caller+0x157/0x760 mm/slab.c:3737
kstrdup+0x39/0x70 mm/util.c:49
bpf_symlink+0x26/0x140 kernel/bpf/inode.c:356
vfs_symlink+0x37a/0x5d0 fs/namei.c:4127
do_symlinkat+0x242/0x2d0 fs/namei.c:4154
__do_sys_symlink fs/namei.c:4173 [inline]
__se_sys_symlink fs/namei.c:4171 [inline]
__x64_sys_symlink+0x59/0x80 fs/namei.c:4171
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 9425:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/kasan.c:521
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xcf/0x230 mm/slab.c:3817
bpf_evict_inode+0x11f/0x150 kernel/bpf/inode.c:565
evict+0x4b9/0x980 fs/inode.c:558
iput_final fs/inode.c:1550 [inline]
iput+0x674/0xa90 fs/inode.c:1576
do_unlinkat+0x733/0xa30 fs/namei.c:4069
__do_sys_unlink fs/namei.c:4110 [inline]
__se_sys_unlink fs/namei.c:4108 [inline]
__x64_sys_unlink+0x42/0x50 fs/namei.c:4108
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
In this scenario path lookup under RCU is racing with the final
unlink in case of symlinks. As Linus puts it in his analysis:
[...] We actually RCU-delay the inode freeing itself, but
when we do the final iput(), the "evict()" function is called
synchronously. Now, the simple fix would seem to just RCU-delay
the kfree() of the symlink data in bpf_evict_inode(). Maybe
that's the right thing to do. [...]
Al suggested to piggy-back on the ->destroy_inode() callback in
order to implement RCU deferral there which can then kfree() the
inode->i_link eventually right before putting inode back into
inode cache. By reusing free_inode_nonrcu() from there we can
avoid the need for our own inode cache and just reuse generic
one as we currently do.
And in-fact on top of all this we should just get rid of the
bpf_evict_inode() entirely. This means truncate_inode_pages_final()
and clear_inode() will then simply be called by the fs core via
evict(). Dropping the reference should really only be done when
inode is unhashed and nothing reachable anymore, so it's better
also moved into the final ->destroy_inode() callback.
Fixes:
0f98621bef5d ("bpf, inode: add support for symlinks and fix mtime/ctime")
Reported-by: syzbot+fb731ca573367b7f6564@syzkaller.appspotmail.com
Reported-by: syzbot+a13e5ead792d6df37818@syzkaller.appspotmail.com
Reported-by: syzbot+7a8ba368b47fdefca61e@syzkaller.appspotmail.com
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Analyzed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lore.kernel.org/lkml/0000000000006946d2057bbd0eef@google.com/T/
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
Pi-Hsun Shih [Wed, 13 Mar 2019 18:44:33 +0000 (11:44 -0700)]
include/linux/swap.h: use offsetof() instead of custom __swapoffset macro
[ Upstream commit
a4046c06be50a4f01d435aa7fe57514818e6cc82 ]
Use offsetof() to calculate offset of a field to take advantage of
compiler built-in version when possible, and avoid UBSAN warning when
compiling with Clang:
UBSAN: Undefined behaviour in mm/swapfile.c:3010:38
member access within null pointer of type 'union swap_header'
CPU: 6 PID: 1833 Comm: swapon Tainted: G S 4.19.23 #43
Call trace:
dump_backtrace+0x0/0x194
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0x70/0x94
ubsan_epilogue+0x14/0x44
ubsan_type_mismatch_common+0xf4/0xfc
__ubsan_handle_type_mismatch_v1+0x34/0x54
__se_sys_swapon+0x654/0x1084
__arm64_sys_swapon+0x1c/0x24
el0_svc_common+0xa8/0x150
el0_svc_compat_handler+0x2c/0x38
el0_svc_compat+0x8/0x18
Link: http://lkml.kernel.org/r/20190312081902.223764-1-pihsun@chromium.org
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chao Yu [Sat, 23 Feb 2019 01:48:27 +0000 (09:48 +0800)]
f2fs: fix to dirty inode for i_mode recovery
[ Upstream commit
ca597bddedd94906cd761d8be6a3ad21292725de ]
As Seulbae Kim reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=202637
We didn't recover permission field correctly after sudden power-cut,
the reason is in setattr we didn't add inode into global dirty list
once i_mode is changed, so latter checkpoint triggered by fsync will
not flush last i_mode into disk, result in this problem, fix it.
Reported-by: Seulbae Kim <seulbae@gatech.edu>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
David Howells [Fri, 8 Mar 2019 12:48:39 +0000 (12:48 +0000)]
rxrpc: Fix client call connect/disconnect race
[ Upstream commit
930c9f9125c85b5134b3e711bc252ecc094708e3 ]
rxrpc_disconnect_client_call() reads the call's connection ID protocol
value (call->cid) as part of that function's variable declarations. This
is bad because it's not inside the locked section and so may race with
someone granting use of the channel to the call.
This manifests as an assertion failure (see below) where the call in the
presumed channel (0 because call->cid wasn't set when we read it) doesn't
match the call attached to the channel we were actually granted (if 1, 2 or
3).
Fix this by moving the read and dependent calculations inside of the
channel_lock section. Also, only set the channel number and pointer
variables if cid is not zero (ie. unset).
This problem can be induced by injecting an occasional error in
rxrpc_wait_for_channel() before the call to schedule().
Make two further changes also:
(1) Add a trace for wait failure in rxrpc_connect_call().
(2) Drop channel_lock before BUG'ing in the case of the assertion failure.
The failure causes a trace akin to the following:
rxrpc: Assertion failed -
18446612685268945920(0xffff8880beab8c00) ==
18446612685268621312(0xffff8880bea69800) is false
------------[ cut here ]------------
kernel BUG at net/rxrpc/conn_client.c:824!
...
RIP: 0010:rxrpc_disconnect_client_call+0x2bf/0x99d
...
Call Trace:
rxrpc_connect_call+0x902/0x9b3
? wake_up_q+0x54/0x54
rxrpc_new_client_call+0x3a0/0x751
? rxrpc_kernel_begin_call+0x141/0x1bc
? afs_alloc_call+0x1b5/0x1b5
rxrpc_kernel_begin_call+0x141/0x1bc
afs_make_call+0x20c/0x525
? afs_alloc_call+0x1b5/0x1b5
? __lock_is_held+0x40/0x71
? lockdep_init_map+0xaf/0x193
? lockdep_init_map+0xaf/0x193
? __lock_is_held+0x40/0x71
? yfs_fs_fetch_data+0x33b/0x34a
yfs_fs_fetch_data+0x33b/0x34a
afs_fetch_data+0xdc/0x3b7
afs_read_dir+0x52d/0x97f
afs_dir_iterate+0xa0/0x661
? iterate_dir+0x63/0x141
iterate_dir+0xa2/0x141
ksys_getdents64+0x9f/0x11b
? filldir+0x111/0x111
? do_syscall_64+0x3e/0x1a0
__x64_sys_getdents64+0x16/0x19
do_syscall_64+0x7d/0x1a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes:
45025bceef17 ("rxrpc: Improve management and caching of client connection objects")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stanislaw Gruszka [Fri, 8 Mar 2019 00:28:18 +0000 (16:28 -0800)]
lib/div64.c: off by one in shift
[ Upstream commit
cdc94a37493135e355dfc0b0e086d84e3eadb50d ]
fls counts bits starting from 1 to 32 (returns 0 for zero argument). If
we add 1 we shift right one bit more and loose precision from divisor,
what cause function incorect results with some numbers.
Corrected code was tested in user-space, see bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=202391
Link: http://lkml.kernel.org/r/1548686944-11891-1-git-send-email-sgruszka@redhat.com
Fixes:
658716d19f8f ("div64_u64(): improve precision on 32bit platforms")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reported-by: Siarhei Volkau <lis8215@gmail.com>
Tested-by: Siarhei Volkau <lis8215@gmail.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
YueHaibing [Fri, 1 Mar 2019 02:57:57 +0000 (10:57 +0800)]
appletalk: Fix use-after-free in atalk_proc_exit
[ Upstream commit
6377f787aeb945cae7abbb6474798de129e1f3ac ]
KASAN report this:
BUG: KASAN: use-after-free in pde_subdir_find+0x12d/0x150 fs/proc/generic.c:71
Read of size 8 at addr
ffff8881f41fe5b0 by task syz-executor.0/2806
CPU: 0 PID: 2806 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xfa/0x1ce lib/dump_stack.c:113
print_address_description+0x65/0x270 mm/kasan/report.c:187
kasan_report+0x149/0x18d mm/kasan/report.c:317
pde_subdir_find+0x12d/0x150 fs/proc/generic.c:71
remove_proc_entry+0xe8/0x420 fs/proc/generic.c:667
atalk_proc_exit+0x18/0x820 [appletalk]
atalk_exit+0xf/0x5a [appletalk]
__do_sys_delete_module kernel/module.c:1018 [inline]
__se_sys_delete_module kernel/module.c:961 [inline]
__x64_sys_delete_module+0x3dc/0x5e0 kernel/module.c:961
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007fb2de6b9c58 EFLAGS:
00000246 ORIG_RAX:
00000000000000b0
RAX:
ffffffffffffffda RBX:
000000000073bf00 RCX:
0000000000462e99
RDX:
0000000000000000 RSI:
0000000000000000 RDI:
00000000200001c0
RBP:
0000000000000002 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
00007fb2de6ba6bc
R13:
00000000004bccaa R14:
00000000006f6bc8 R15:
00000000ffffffff
Allocated by task 2806:
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496
slab_post_alloc_hook mm/slab.h:444 [inline]
slab_alloc_node mm/slub.c:2739 [inline]
slab_alloc mm/slub.c:2747 [inline]
kmem_cache_alloc+0xcf/0x250 mm/slub.c:2752
kmem_cache_zalloc include/linux/slab.h:730 [inline]
__proc_create+0x30f/0xa20 fs/proc/generic.c:408
proc_mkdir_data+0x47/0x190 fs/proc/generic.c:469
0xffffffffc10c01bb
0xffffffffc10c0166
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 2806:
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x130/0x180 mm/kasan/common.c:458
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook mm/slub.c:1436 [inline]
slab_free mm/slub.c:2986 [inline]
kmem_cache_free+0xa6/0x2a0 mm/slub.c:3002
pde_put+0x6e/0x80 fs/proc/generic.c:647
remove_proc_entry+0x1d3/0x420 fs/proc/generic.c:684
0xffffffffc10c031c
0xffffffffc10c0166
do_one_initcall+0xfa/0x5ca init/main.c:887
do_init_module+0x204/0x5f6 kernel/module.c:3460
load_module+0x66b2/0x8570 kernel/module.c:3808
__do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902
do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at
ffff8881f41fe500
which belongs to the cache proc_dir_entry of size 256
The buggy address is located 176 bytes inside of
256-byte region [
ffff8881f41fe500,
ffff8881f41fe600)
The buggy address belongs to the page:
page:
ffffea0007d07f80 count:1 mapcount:0 mapping:
ffff8881f6e69a00 index:0x0
flags: 0x2fffc0000000200(slab)
raw:
02fffc0000000200 dead000000000100 dead000000000200 ffff8881f6e69a00
raw:
0000000000000000 00000000800c000c 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881f41fe480: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff8881f41fe500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>
ffff8881f41fe580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881f41fe600: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff8881f41fe680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
It should check the return value of atalk_proc_init fails,
otherwise atalk_exit will trgger use-after-free in pde_subdir_find
while unload the module.This patch fix error cleanup path of atalk_init
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kevin Wang [Fri, 22 Feb 2019 04:36:49 +0000 (12:36 +0800)]
drm/amdkfd: use init_mqd function to allocate object for hid_mqd (CI)
[ Upstream commit
cac734c2dbd2514f14c8c6a17caba1990d83bf1d ]
if use the legacy method to allocate object, when mqd_hiq need to run
uninit code, it will be cause WARNING call trace.
eg: (s3 suspend test)
[ 34.918944] Call Trace:
[ 34.918948] [<
ffffffff92961dc1>] dump_stack+0x19/0x1b
[ 34.918950] [<
ffffffff92297648>] __warn+0xd8/0x100
[ 34.918951] [<
ffffffff9229778d>] warn_slowpath_null+0x1d/0x20
[ 34.918991] [<
ffffffffc03ce1fe>] uninit_mqd_hiq_sdma+0x4e/0x50 [amdgpu]
[ 34.919028] [<
ffffffffc03d0ef7>] uninitialize+0x37/0xe0 [amdgpu]
[ 34.919064] [<
ffffffffc03d15a6>] kernel_queue_uninit+0x16/0x30 [amdgpu]
[ 34.919086] [<
ffffffffc03d26c2>] pm_uninit+0x12/0x20 [amdgpu]
[ 34.919107] [<
ffffffffc03d4915>] stop_nocpsch+0x15/0x20 [amdgpu]
[ 34.919129] [<
ffffffffc03c1dce>] kgd2kfd_suspend.part.4+0x2e/0x50 [amdgpu]
[ 34.919150] [<
ffffffffc03c2667>] kgd2kfd_suspend+0x17/0x20 [amdgpu]
[ 34.919171] [<
ffffffffc03c103a>] amdgpu_amdkfd_suspend+0x1a/0x20 [amdgpu]
[ 34.919187] [<
ffffffffc02ec428>] amdgpu_device_suspend+0x88/0x3a0 [amdgpu]
[ 34.919189] [<
ffffffff922e22cf>] ? enqueue_entity+0x2ef/0xbe0
[ 34.919205] [<
ffffffffc02e8220>] amdgpu_pmops_suspend+0x20/0x30 [amdgpu]
[ 34.919207] [<
ffffffff925c56ff>] pci_pm_suspend+0x6f/0x150
[ 34.919208] [<
ffffffff925c5690>] ? pci_pm_freeze+0xf0/0xf0
[ 34.919210] [<
ffffffff926b45c6>] dpm_run_callback+0x46/0x90
[ 34.919212] [<
ffffffff926b49db>] __device_suspend+0xfb/0x2a0
[ 34.919213] [<
ffffffff926b4b9f>] async_suspend+0x1f/0xa0
[ 34.919214] [<
ffffffff922c918f>] async_run_entry_fn+0x3f/0x130
[ 34.919216] [<
ffffffff922b9d4f>] process_one_work+0x17f/0x440
[ 34.919217] [<
ffffffff922bade6>] worker_thread+0x126/0x3c0
[ 34.919218] [<
ffffffff922bacc0>] ? manage_workers.isra.25+0x2a0/0x2a0
[ 34.919220] [<
ffffffff922c1c31>] kthread+0xd1/0xe0
[ 34.919221] [<
ffffffff922c1b60>] ? insert_kthread_work+0x40/0x40
[ 34.919222] [<
ffffffff92974c1d>] ret_from_fork_nospec_begin+0x7/0x21
[ 34.919224] [<
ffffffff922c1b60>] ? insert_kthread_work+0x40/0x40
[ 34.919224] ---[ end trace
38cd9f65c963adad ]---
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Shi [Wed, 13 Feb 2019 16:14:23 +0000 (17:14 +0100)]
ARM: 8839/1: kprobe: make patch_lock a raw_spinlock_t
[ Upstream commit
143c2a89e0e5fda6c6fd08d7bc1126438c19ae90 ]
When running kprobe on -rt kernel, the below bug is caught:
|BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:931
|in_atomic(): 1, irqs_disabled(): 128, pid: 14, name: migration/0
|Preemption disabled at:[<
802f2b98>] cpu_stopper_thread+0xc0/0x140
|CPU: 0 PID: 14 Comm: migration/0 Tainted: G O 4.8.3-rt2 #1
|Hardware name: Freescale LS1021A
|[<
8025a43c>] (___might_sleep)
|[<
80b5b324>] (rt_spin_lock)
|[<
80b5c31c>] (__patch_text_real)
|[<
80b5c3ac>] (patch_text_stop_machine)
|[<
802f2920>] (multi_cpu_stop)
Since patch_text_stop_machine() is called in stop_machine() which
disables IRQ, sleepable lock should be not used in this atomic context,
so replace patch_lock to raw lock.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ilia Mirkin [Sun, 13 Jan 2019 22:50:10 +0000 (17:50 -0500)]
drm/nouveau/volt/gf117: fix speedo readout register
[ Upstream commit
fc782242749fa4235592854fafe1a1297583c1fb ]
GF117 appears to use the same register as GK104 (but still with the
general Fermi readout mechanism).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108980
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mika Westerberg [Thu, 31 Jan 2019 16:38:56 +0000 (19:38 +0300)]
PCI: Blacklist power management of Gigabyte X299 DESIGNARE EX PCIe ports
[ Upstream commit
85b0cae89d5266e6a7abb2e83c6f716326fc494c ]
Gigabyte X299 DESIGNARE EX motherboard has one PCIe root port that is
connected to an Alpine Ridge Thunderbolt controller. This port has slot
implemented bit set in the config space but other than that it is not
hotplug capable in the sense we are expecting in Linux (it has
dev->is_hotplug_bridge set to 0):
00:1c.4 PCI bridge: Intel Corporation 200 Series PCH PCI Express Root Port #5
Bus: primary=00, secondary=05, subordinate=46, sec-latency=0
Memory behind bridge:
78000000-
8fffffff [size=384M]
Prefetchable memory behind bridge:
00003800f8000000-
00003800ffffffff [size=128M]
...
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
...
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #8, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet+ LinkState+
This system is using ACPI based hotplug to notify the OS that it needs to
rescan the PCI bus (ACPI hotplug).
If there is nothing connected in any of the Thunderbolt ports the root port
will not have any runtime PM active children and is thus automatically
runtime suspended pretty soon after boot by PCI PM core. Now, when a
device is connected the BIOS SMI handler responsible for enumerating newly
added devices is not able to find anything because the port is in D3.
Prevent this from happening by blacklisting PCI power management of this
particular Gigabyte system.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202031
Reported-by: Kedar A Dongre <kedar.a.dongre@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Leo Yan [Tue, 5 Feb 2019 23:24:53 +0000 (16:24 -0700)]
coresight: cpu-debug: Support for CA73 CPUs
[ Upstream commit
a0f890aba2be33377f4eb24e13633c4a76a68f38 ]
This patch is to add the AMBA device ID for CA73 CPU, so that CPU debug
module can be initialized successfully when a SoC contain CA73 CPUs.
This patch has been verified on 96boards Hikey960.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhang Rui [Fri, 1 Feb 2019 06:13:41 +0000 (14:13 +0800)]
Revert "ACPI / EC: Remove old CLEAR_ON_RESUME quirk"
[ Upstream commit
b6a3e1475b0220378ad32bdf4d8692f058b1fc03 ]
On some Samsung hardware, it is necessary to clear events accumulated by
the EC during sleep. These ECs stop reporting GPEs until they are manually
polled, if too many events are accumulated.
Thus the CLEAR_ON_RESUME quirk is introduced to send EC query commands
unconditionally after resume to clear all the EC query events on those
platforms.
Later, commit
4c237371f290 ("ACPI / EC: Remove old CLEAR_ON_RESUME quirk")
removes the CLEAR_ON_RESUME quirk because we thought the new EC IRQ
polling logic should handle this case.
Now it has been proved that the EC IRQ Polling logic does not fix the
issue actually because we got regression report on these Samsung
platforms after removing the quirk.
Thus revert commit
4c237371f290 ("ACPI / EC: Remove old CLEAR_ON_RESUME
quirk") to introduce back the Samsung quirk in this patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161
Tested-by: Ortwin Glück <odi@odi.ch>
Tested-by: Francisco Cribari <cribari@gmail.com>
Tested-by: Balazs Varga <balazs4web@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lars Persson [Wed, 23 Jan 2019 11:59:42 +0000 (12:59 +0100)]
crypto: axis - fix for recursive locking from bottom half
[ Upstream commit
c34a83820f59bb275e5f2d55cd5ea99c64f6ef23 ]
Clients may submit a new requests from the completion callback
context. The driver was not prepared to receive a request in this
state because it already held the request queue lock and a recursive
lock error is triggered.
Now all completions are queued up until we are ready to drop the queue
lock and then delivered.
The fault was triggered by TCP over an IPsec connection in the LTP
test suite:
LTP: starting tcp4_ipsec02 (tcp_ipsec.sh -p ah -m transport -s "100 1000 65535")
BUG: spinlock recursion on CPU#1, genload/943
lock: 0xbf3c3094, .magic:
dead4ead, .owner: genload/943, .owner_cpu: 1
CPU: 1 PID: 943 Comm: genload Tainted: G O 4.9.62-axis5-devel #6
Hardware name: Axis ARTPEC-6 Platform
(unwind_backtrace) from [<
8010d134>] (show_stack+0x18/0x1c)
(show_stack) from [<
803a289c>] (dump_stack+0x84/0x98)
(dump_stack) from [<
8016e164>] (do_raw_spin_lock+0x124/0x128)
(do_raw_spin_lock) from [<
804de1a4>] (artpec6_crypto_submit+0x2c/0xa0)
(artpec6_crypto_submit) from [<
804def38>] (artpec6_crypto_prepare_submit_hash+0xd0/0x54c)
(artpec6_crypto_prepare_submit_hash) from [<
7f3165f0>] (ah_output+0x2a4/0x3dc [ah4])
(ah_output [ah4]) from [<
805df9bc>] (xfrm_output_resume+0x178/0x4a4)
(xfrm_output_resume) from [<
805d283c>] (xfrm4_output+0xac/0xbc)
(xfrm4_output) from [<
80587928>] (ip_queue_xmit+0x140/0x3b4)
(ip_queue_xmit) from [<
805a13b4>] (tcp_transmit_skb+0x4c4/0x95c)
(tcp_transmit_skb) from [<
8059f218>] (tcp_rcv_state_process+0xdf4/0xdfc)
(tcp_rcv_state_process) from [<
805a7530>] (tcp_v4_do_rcv+0x64/0x1ac)
(tcp_v4_do_rcv) from [<
805a9724>] (tcp_v4_rcv+0xa34/0xb74)
(tcp_v4_rcv) from [<
80581d34>] (ip_local_deliver_finish+0x78/0x2b0)
(ip_local_deliver_finish) from [<
8058259c>] (ip_local_deliver+0xe4/0x104)
(ip_local_deliver) from [<
805d23ec>] (xfrm4_transport_finish+0xf4/0x144)
(xfrm4_transport_finish) from [<
805df564>] (xfrm_input+0x4f4/0x74c)
(xfrm_input) from [<
804de420>] (artpec6_crypto_task+0x208/0x38c)
(artpec6_crypto_task) from [<
801271b0>] (tasklet_action+0x60/0xec)
(tasklet_action) from [<
801266d4>] (__do_softirq+0xcc/0x3a4)
(__do_softirq) from [<
80126d20>] (irq_exit+0xf4/0x15c)
(irq_exit) from [<
801741e8>] (__handle_domain_irq+0x68/0xbc)
(__handle_domain_irq) from [<
801014f0>] (gic_handle_irq+0x50/0x94)
(gic_handle_irq) from [<
80657370>] (__irq_usr+0x50/0x80)
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hsin-Yi, Wang [Wed, 9 Jan 2019 06:59:22 +0000 (14:59 +0800)]
drm/panel: panel-innolux: set display off in innolux_panel_unprepare
[ Upstream commit
46f3ceaffa81e846677bca8668e0ad40e643cffd ]
Move mipi_dsi_dcs_set_display_off() from innolux_panel_disable()
to innolux_panel_unprepare(), so they are consistent with
innolux_panel_enable() and innolux_panel_prepare().
This also fixes some mode check and irq timeout issue in MTK dsi code.
Since some dsi code (e.g. mtk_dsi) have following call trace:
1. drm_panel_disable(), which calls innolux_panel_disable()
2. switch to cmd mode
3. drm_panel_unprepare(), which calls innolux_panel_unprepare()
However, mtk_dsi needs to be in cmd mode to be able to send commands
(e.g. mipi_dsi_dcs_set_display_off() and mipi_dsi_dcs_enter_sleep_mode()),
so we need these functions to be called after the switch to cmd mode happens,
i.e. in innolux_panel_unprepare.
Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190109065922.231753-1-hsinyi@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christophe Leroy [Fri, 14 Dec 2018 15:26:20 +0000 (15:26 +0000)]
lkdtm: Add tests for NULL pointer dereference
[ Upstream commit
59a12205d3c32aee4c13ca36889fdf7cfed31126 ]
Introduce lkdtm tests for NULL pointer dereference: check access or exec
at NULL address, since these errors tend to be reported differently from
the general fault error text. For example from x86:
pr_alert("BUG: unable to handle kernel %s at %px\n",
address < PAGE_SIZE ? "NULL pointer dereference" : "paging request",
(void *)address);
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christophe Leroy [Wed, 7 Nov 2018 20:14:10 +0000 (20:14 +0000)]
lkdtm: Print real addresses
[ Upstream commit
4c411157a42f122051ae3469bee0b5cabe89e139 ]
Today, when doing a lkdtm test before the readiness of the
random generator, (ptrval) is printed instead of the address
at which it perform the fault:
[ 1597.337030] lkdtm: Performing direct entry EXEC_USERSPACE
[ 1597.337142] lkdtm: attempting ok execution at (ptrval)
[ 1597.337398] lkdtm: attempting bad execution at (ptrval)
[ 1597.337460] kernel tried to execute user page (
77858000) -exploit attempt? (uid: 0)
[ 1597.344769] Unable to handle kernel paging request for instruction fetch
[ 1597.351392] Faulting instruction address: 0x77858000
[ 1597.356312] Oops: Kernel access of bad area, sig: 11 [#1]
If the lkdtm test is done later on, it prints an hashed address.
In both cases this is pointless. The purpose of the test is to
ensure the kernel generates an Oops at the expected address,
so real addresses needs to be printed. This patch fixes that.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dmitry Osipenko [Sun, 21 Oct 2018 18:36:14 +0000 (21:36 +0300)]
soc/tegra: pmc: Drop locking from tegra_powergate_is_powered()
[ Upstream commit
b6e1fd17a38bd1d97c11d69fd3207b3ef9bfa4b3 ]
This fixes splats like the one below if CONFIG_DEBUG_ATOMIC_SLEEP=y
and machine (Tegra30) booted with SMP=n or all secondary CPU's are put
offline. Locking isn't needed because it protects atomic operation.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G C
4.18.0-next-20180821-00180-gc3ebb6544e44-dirty #823
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[<
c01134f4>] (unwind_backtrace) from [<
c010db2c>] (show_stack+0x20/0x24)
[<
c010db2c>] (show_stack) from [<
c0bd0f3c>] (dump_stack+0x94/0xa8)
[<
c0bd0f3c>] (dump_stack) from [<
c0151df8>] (___might_sleep+0x13c/0x174)
[<
c0151df8>] (___might_sleep) from [<
c0151ea0>] (__might_sleep+0x70/0xa8)
[<
c0151ea0>] (__might_sleep) from [<
c0bec2b8>] (mutex_lock+0x2c/0x70)
[<
c0bec2b8>] (mutex_lock) from [<
c0589844>] (tegra_powergate_is_powered+0x44/0xa8)
[<
c0589844>] (tegra_powergate_is_powered) from [<
c0581a60>] (tegra30_cpu_rail_off_ready+0x30/0x74)
[<
c0581a60>] (tegra30_cpu_rail_off_ready) from [<
c0122244>] (tegra30_idle_lp2+0xa0/0x108)
[<
c0122244>] (tegra30_idle_lp2) from [<
c0853438>] (cpuidle_enter_state+0x140/0x540)
[<
c0853438>] (cpuidle_enter_state) from [<
c08538a4>] (cpuidle_enter+0x40/0x4c)
[<
c08538a4>] (cpuidle_enter) from [<
c01595e0>] (call_cpuidle+0x30/0x48)
[<
c01595e0>] (call_cpuidle) from [<
c01599f8>] (do_idle+0x238/0x28c)
[<
c01599f8>] (do_idle) from [<
c0159d28>] (cpu_startup_entry+0x28/0x2c)
[<
c0159d28>] (cpu_startup_entry) from [<
c0be76c8>] (rest_init+0xd8/0xdc)
[<
c0be76c8>] (rest_init) from [<
c1200f50>] (start_kernel+0x41c/0x430)
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Wed, 27 Feb 2019 00:35:26 +0000 (16:35 -0800)]
scsi: core: Avoid that system resume triggers a kernel warning
[ Upstream commit
388b4e6a00bb3097278ed1648ac5a1cb48c894e6 ]
scsi_device_quiesce() and scsi_device_resume() are called during
system-wide suspend and resume. scsi_device_quiesce() only succeeds for
SCSI devices that are in one of the RUNNING, OFFLINE or TRANSPORT_OFFLINE
states (see also scsi_set_device_state()). This patch avoids that the
following warning is triggered when resuming a system for which quiescing a
SCSI device failed:
WARNING: CPU: 2 PID: 11303 at drivers/scsi/scsi_lib.c:2600 scsi_device_resume+0x4f/0x58
CPU: 2 PID: 11303 Comm: kworker/u8:70 Not tainted 5.0.0-rc1+ #50
Hardware name: LENOVO 80E3/Lancer 5B2, BIOS A2CN45WW(V2.13) 08/04/2016
Workqueue: events_unbound async_run_entry_fn
Call Trace:
scsi_dev_type_resume+0x2e/0x60
async_run_entry_fn+0x32/0xd8
process_one_work+0x1f4/0x420
worker_thread+0x28/0x3c0
kthread+0x118/0x130
ret_from_fork+0x22/0x40
Cc: Przemek Socha <soprwa@gmail.com>
Reported-by: Przemek Socha <soprwa@gmail.com>
Fixes:
3a0a529971ec ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Julia Cartwright [Wed, 20 Feb 2019 16:46:31 +0000 (16:46 +0000)]
iommu/dmar: Fix buffer overflow during PCI bus notification
[ Upstream commit
cffaaf0c816238c45cd2d06913476c83eb50f682 ]
Commit
57384592c433 ("iommu/vt-d: Store bus information in RMRR PCI
device path") changed the type of the path data, however, the change in
path type was not reflected in size calculations. Update to use the
correct type and prevent a buffer overflow.
This bug manifests in systems with deep PCI hierarchies, and can lead to
an overflow of the static allocated buffer (dmar_pci_notify_info_buf),
or can lead to overflow of slab-allocated data.
BUG: KASAN: global-out-of-bounds in dmar_alloc_pci_notify_info+0x1d5/0x2e0
Write of size 1 at addr
ffffffff90445d80 by task swapper/0/1
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W
4.14.87-rt49-02406-gd0a0e96 #1
Call Trace:
? dump_stack+0x46/0x59
? print_address_description+0x1df/0x290
? dmar_alloc_pci_notify_info+0x1d5/0x2e0
? kasan_report+0x256/0x340
? dmar_alloc_pci_notify_info+0x1d5/0x2e0
? e820__memblock_setup+0xb0/0xb0
? dmar_dev_scope_init+0x424/0x48f
? __down_write_common+0x1ec/0x230
? dmar_dev_scope_init+0x48f/0x48f
? dmar_free_unused_resources+0x109/0x109
? cpumask_next+0x16/0x20
? __kmem_cache_create+0x392/0x430
? kmem_cache_create+0x135/0x2f0
? e820__memblock_setup+0xb0/0xb0
? intel_iommu_init+0x170/0x1848
? _raw_spin_unlock_irqrestore+0x32/0x60
? migrate_enable+0x27a/0x5b0
? sched_setattr+0x20/0x20
? migrate_disable+0x1fc/0x380
? task_rq_lock+0x170/0x170
? try_to_run_init_process+0x40/0x40
? locks_remove_file+0x85/0x2f0
? dev_prepare_static_identity_mapping+0x78/0x78
? rt_spin_unlock+0x39/0x50
? lockref_put_or_lock+0x2a/0x40
? dput+0x128/0x2f0
? __rcu_read_unlock+0x66/0x80
? __fput+0x250/0x300
? __rcu_read_lock+0x1b/0x30
? mntput_no_expire+0x38/0x290
? e820__memblock_setup+0xb0/0xb0
? pci_iommu_init+0x25/0x63
? pci_iommu_init+0x25/0x63
? do_one_initcall+0x7e/0x1c0
? initcall_blacklisted+0x120/0x120
? kernel_init_freeable+0x27b/0x307
? rest_init+0xd0/0xd0
? kernel_init+0xf/0x120
? rest_init+0xd0/0xd0
? ret_from_fork+0x1f/0x40
The buggy address belongs to the variable:
dmar_pci_notify_info_buf+0x40/0x60
Fixes:
57384592c433 ("iommu/vt-d: Store bus information in RMRR PCI device path")
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lorenzo Bianconi [Wed, 20 Feb 2019 08:23:03 +0000 (09:23 +0100)]
net: ip6_gre: fix possible NULL pointer dereference in ip6erspan_set_version
[ Upstream commit
efcc9bcaf77c07df01371a7c34e50424c291f3ac ]
Fix a possible NULL pointer dereference in ip6erspan_set_version checking
nlattr data pointer
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 7549 Comm: syz-executor432 Not tainted 5.0.0-rc6-next-
20190218
#37
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:ip6erspan_set_version+0x5c/0x350 net/ipv6/ip6_gre.c:1726
Code: 07 38 d0 7f 08 84 c0 0f 85 9f 02 00 00 49 8d bc 24 b0 00 00 00 c6 43
54 01 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f
85 9a 02 00 00 4d 8b ac 24 b0 00 00 00 4d 85 ed 0f
RSP: 0018:
ffff888089ed7168 EFLAGS:
00010202
RAX:
dffffc0000000000 RBX:
ffff8880869d6e58 RCX:
0000000000000000
RDX:
0000000000000016 RSI:
ffffffff862736b4 RDI:
00000000000000b0
RBP:
ffff888089ed7180 R08:
1ffff11010d3adcb R09:
ffff8880869d6e58
R10:
ffffed1010d3add5 R11:
ffff8880869d6eaf R12:
0000000000000000
R13:
ffffffff8931f8c0 R14:
ffffffff862825d0 R15:
ffff8880869d6e58
FS:
0000000000b3d880(0000) GS:
ffff8880ae900000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000020000184 CR3:
0000000092cc5000 CR4:
00000000001406e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
ip6erspan_newlink+0x66/0x7b0 net/ipv6/ip6_gre.c:2210
__rtnl_newlink+0x107b/0x16c0 net/core/rtnetlink.c:3176
rtnl_newlink+0x69/0xa0 net/core/rtnetlink.c:3234
rtnetlink_rcv_msg+0x465/0xb00 net/core/rtnetlink.c:5192
netlink_rcv_skb+0x17a/0x460 net/netlink/af_netlink.c:2485
rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5210
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0x536/0x720 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x8ae/0xd70 net/netlink/af_netlink.c:1925
sock_sendmsg_nosec net/socket.c:621 [inline]
sock_sendmsg+0xdd/0x130 net/socket.c:631
___sys_sendmsg+0x806/0x930 net/socket.c:2136
__sys_sendmsg+0x105/0x1d0 net/socket.c:2174
__do_sys_sendmsg net/socket.c:2183 [inline]
__se_sys_sendmsg net/socket.c:2181 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2181
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x440159
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7
48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff
ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007fffa69156e8 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
00000000004002c8 RCX:
0000000000440159
RDX:
0000000000000000 RSI:
0000000020001340 RDI:
0000000000000003
RBP:
00000000006ca018 R08:
0000000000000001 R09:
00000000004002c8
R10:
0000000000000011 R11:
0000000000000246 R12:
00000000004019e0
R13:
0000000000401a70 R14:
0000000000000000 R15:
0000000000000000
Modules linked in:
---[ end trace
09f8a7d13b4faaa1 ]---
RIP: 0010:ip6erspan_set_version+0x5c/0x350 net/ipv6/ip6_gre.c:1726
Code: 07 38 d0 7f 08 84 c0 0f 85 9f 02 00 00 49 8d bc 24 b0 00 00 00 c6 43
54 01 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f
85 9a 02 00 00 4d 8b ac 24 b0 00 00 00 4d 85 ed 0f
RSP: 0018:
ffff888089ed7168 EFLAGS:
00010202
RAX:
dffffc0000000000 RBX:
ffff8880869d6e58 RCX:
0000000000000000
RDX:
0000000000000016 RSI:
ffffffff862736b4 RDI:
00000000000000b0
RBP:
ffff888089ed7180 R08:
1ffff11010d3adcb R09:
ffff8880869d6e58
R10:
ffffed1010d3add5 R11:
ffff8880869d6eaf R12:
0000000000000000
R13:
ffffffff8931f8c0 R14:
ffffffff862825d0 R15:
ffff8880869d6e58
FS:
0000000000b3d880(0000) GS:
ffff8880ae900000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000020000184 CR3:
0000000092cc5000 CR4:
00000000001406e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Fixes:
4974d5f678ab ("net: ip6_gre: initialize erspan_ver just for erspan tunnels")
Reported-and-tested-by: syzbot+30191cf1057abd3064af@syzkaller.appspotmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ard Biesheuvel [Sat, 16 Feb 2019 13:51:26 +0000 (14:51 +0100)]
crypto: sha512/arm - fix crash bug in Thumb2 build
[ Upstream commit
c64316502008064c158fa40cc250665e461b0f2a ]
The SHA512 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address
bf825000
pgd =
42f44b11
[
bf825000] *pgd=
80000040206003, *pmd=
5f1bd003, *pte=
00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<
bf820bca>] lr : [<
bf824ffd>] psr:
800b0033
sp :
ebc8bbe8 ip :
faaabe1c fp :
2fdd3433
r10:
4c5f1692 r9 :
e43037df r8 :
b04b0a5a
r7 :
c369d722 r6 :
39c3693e r5 :
7a013189 r4 :
1580d26b
r3 :
8762a9b0 r2 :
eea9c2cd r1 :
3e9ab536 r0 :
1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control:
70c5383d Table:
6b8467c0 DAC:
dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address
bf820bca
unwind: Index not found
bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace
e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ard Biesheuvel [Sat, 16 Feb 2019 13:51:25 +0000 (14:51 +0100)]
crypto: sha256/arm - fix crash bug in Thumb2 build
[ Upstream commit
69216a545cf81b2b32d01948f7039315abaf75a0 ]
The SHA256 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address
bf825000
pgd =
42f44b11
[
bf825000] *pgd=
80000040206003, *pmd=
5f1bd003, *pte=
00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<
bf820bca>] lr : [<
bf824ffd>] psr:
800b0033
sp :
ebc8bbe8 ip :
faaabe1c fp :
2fdd3433
r10:
4c5f1692 r9 :
e43037df r8 :
b04b0a5a
r7 :
c369d722 r6 :
39c3693e r5 :
7a013189 r4 :
1580d26b
r3 :
8762a9b0 r2 :
eea9c2cd r1 :
3e9ab536 r0 :
1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control:
70c5383d Table:
6b8467c0 DAC:
dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address
bf820bca
unwind: Index not found
bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace
e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Cong Wang [Thu, 31 Jan 2019 21:05:49 +0000 (13:05 -0800)]
xfrm: destroy xfrm_state synchronously on net exit path
[ Upstream commit
f75a2804da391571563c4b6b29e7797787332673 ]
xfrm_state_put() moves struct xfrm_state to the GC list
and schedules the GC work to clean it up. On net exit call
path, xfrm_state_flush() is called to clean up and
xfrm_flush_gc() is called to wait for the GC work to complete
before exit.
However, this doesn't work because one of the ->destructor(),
ipcomp_destroy(), schedules the same GC work again inside
the GC work. It is hard to wait for such a nested async
callback. This is also why syzbot still reports the following
warning:
WARNING: CPU: 1 PID: 33 at net/ipv6/xfrm6_tunnel.c:351 xfrm6_tunnel_net_exit+0x2cb/0x500 net/ipv6/xfrm6_tunnel.c:351
...
ops_exit_list.isra.0+0xb0/0x160 net/core/net_namespace.c:153
cleanup_net+0x51d/0xb10 net/core/net_namespace.c:551
process_one_work+0xd0c/0x1ce0 kernel/workqueue.c:2153
worker_thread+0x143/0x14a0 kernel/workqueue.c:2296
kthread+0x357/0x430 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
In fact, it is perfectly fine to bypass GC and destroy xfrm_state
synchronously on net exit call path, because it is in process context
and doesn't need a work struct to do any blocking work.
This patch introduces xfrm_state_put_sync() which simply bypasses
GC, and lets its callers to decide whether to use this synchronous
version. On net exit path, xfrm_state_fini() and
xfrm6_tunnel_net_exit() use it. And, as ipcomp_destroy() itself is
blocking, it can use xfrm_state_put_sync() directly too.
Also rename xfrm_state_gc_destroy() to ___xfrm_state_destroy() to
reflect this change.
Fixes:
b48c05ab5d32 ("xfrm: Fix warning in xfrm6_tunnel_net_exit.")
Reported-and-tested-by: syzbot+e9aebef558e3ed673934@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
shamir rabinovitch [Sun, 16 Dec 2018 07:01:08 +0000 (09:01 +0200)]
net/rds: fix warn in rds_message_alloc_sgs
[ Upstream commit
ea010070d0a7497253d5a6f919f6dd107450b31a ]
redundant copy_from_user in rds_sendmsg system call expose rds
to issue where rds_rdma_extra_size walk the rds iovec and and
calculate the number pf pages (sgs) it need to add to the tail of
rds message and later rds_cmsg_rdma_args copy the rds iovec again
and re calculate the same number and get different result causing
WARN_ON in rds_message_alloc_sgs.
fix this by doing the copy_from_user only once per rds_sendmsg
system call.
When issue occur the below dump is seen:
WARNING: CPU: 0 PID: 19789 at net/rds/message.c:316 rds_message_alloc_sgs+0x10c/0x160 net/rds/message.c:316
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 19789 Comm: syz-executor827 Not tainted 4.19.0-next-
20181030+ #101
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
panic+0x2ad/0x55c kernel/panic.c:188
__warn.cold.8+0x20/0x45 kernel/panic.c:540
report_bug+0x254/0x2d0 lib/bug.c:186
fixup_bug arch/x86/kernel/traps.c:178 [inline]
do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:271
do_invalid_op+0x36/0x40 arch/x86/kernel/traps.c:290
invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:969
RIP: 0010:rds_message_alloc_sgs+0x10c/0x160 net/rds/message.c:316
Code: c0 74 04 3c 03 7e 6c 44 01 ab 78 01 00 00 e8 2b 9e 35 fa 4c 89 e0 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d c3 e8 14 9e 35 fa <0f> 0b 31 ff 44 89 ee e8 18 9f 35 fa 45 85 ed 75 1b e8 fe 9d 35 fa
RSP: 0018:
ffff8801c51b7460 EFLAGS:
00010293
RAX:
ffff8801bc412080 RBX:
ffff8801d7bf4040 RCX:
ffffffff8749c9e6
RDX:
0000000000000000 RSI:
ffffffff8749ca5c RDI:
0000000000000004
RBP:
ffff8801c51b7490 R08:
ffff8801bc412080 R09:
ffffed003b5c5b67
R10:
ffffed003b5c5b67 R11:
ffff8801dae2db3b R12:
0000000000000000
R13:
000000000007165c R14:
000000000007165c R15:
0000000000000005
rds_cmsg_rdma_args+0x82d/0x1510 net/rds/rdma.c:623
rds_cmsg_send net/rds/send.c:971 [inline]
rds_sendmsg+0x19a2/0x3180 net/rds/send.c:1273
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:632
___sys_sendmsg+0x7fd/0x930 net/socket.c:2117
__sys_sendmsg+0x11d/0x280 net/socket.c:2155
__do_sys_sendmsg net/socket.c:2164 [inline]
__se_sys_sendmsg net/socket.c:2162 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2162
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x44a859
Code: e8 dc e6 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 6b cb fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007f1d4710ada8 EFLAGS:
00000297 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
00000000006dcc28 RCX:
000000000044a859
RDX:
0000000000000000 RSI:
0000000020001600 RDI:
0000000000000003
RBP:
00000000006dcc20 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000297 R12:
00000000006dcc2c
R13:
646e732f7665642f R14:
00007f1d4710b9c0 R15:
00000000006dcd2c
Kernel Offset: disabled
Rebooting in 86400 seconds..
Reported-by: syzbot+26de17458aeda9d305d8@syzkaller.appspotmail.com
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: shamir rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rafael J. Wysocki [Mon, 17 Dec 2018 11:21:55 +0000 (12:21 +0100)]
ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle
[ Upstream commit
f941d3e41da7f86bdb9dcc1977c2bcc6b89bfe47 ]
There are systems in which non-wakeup GPEs fire during the "noirq"
suspend stage of suspending devices and that effectively prevents the
system that tries to suspend to idle from entering any low-power
state at all. If the offending GPE fires regularly and often enough,
the system appears to be suspended, but in fact it is in a tight loop
over "noirq" suspend and "noirq" resume of devices all the time.
To prevent that from happening, disable all non-wakeup GPEs except
for the EC GPE for suspend-to-idle (the EC GPE is special, because
on some systems it has to be enabled for power button wakeup events
to be generated as expected).
Fixes:
147a7d9d25ca (ACPI / PM: Do not reconfigure GPEs for suspend-to-idle)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201987
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ayman Bagabas [Wed, 12 Dec 2018 23:07:57 +0000 (18:07 -0500)]
ALSA: hda: fix front speakers on Huawei MBXP
[ Upstream commit
8ac51bbc4cfec4ef08b03bef24b31e2d50ef8b37 ]
This patch solves bug 200501 'Only 2 of 4 speakers playing sound.'
It enables the front speakers on Huawei Matebook X Pro laptops.
These laptops come with Dolby Atmos sound system and these pins
configuration enables the front speakers.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200501
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Trigger Huang [Tue, 6 Nov 2018 11:37:58 +0000 (19:37 +0800)]
drm/ttm: Fix bo_global and mem_global kfree error
[ Upstream commit
30f33126feca0fe16df9e9302ffc28a953e2eb37 ]
ttm_bo_glob and ttm_mem_glob are defined as structure instance, while
not allocated by kzalloc, so kfree should not be invoked to release
them anymore. Otherwise, it will cause the following kernel BUG when
unloading amdgpu module
[ 48.419294] kernel BUG at /build/linux-5s7Xkn/linux-4.15.0/mm/slub.c:3894!
[ 48.419352] invalid opcode: 0000 [#1] SMP PTI
[ 48.419387] Modules linked in: amdgpu(OE-) amdchash(OE) amdttm(OE) amd_sched(OE) amdkcl(OE) amd_iommu_v2 drm_kms_helper drm i2c_algo_bit fb_sys_fops syscopyarea sysfillrect sysimgblt snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_pcm snd_seq_midi snd_seq_midi_event snd_rawmidi pcbc snd_seq snd_seq_device snd_timer aesni_intel snd soundcore joydev aes_x86_64 crypto_simd glue_helper cryptd input_leds mac_hid serio_raw binfmt_misc nfsd auth_rpcgss nfs_acl lockd grace sunrpc sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables autofs4 8139too psmouse i2c_piix4 8139cp mii floppy pata_acpi
[ 48.419782] CPU: 1 PID: 1281 Comm: modprobe Tainted: G OE 4.15.0-20-generic #21-Ubuntu
[ 48.419838] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 48.419901] RIP: 0010:kfree+0x137/0x180
[ 48.419934] RSP: 0018:
ffffb02101273bf8 EFLAGS:
00010246
[ 48.419974] RAX:
ffffeee1418ad7e0 RBX:
ffffffffc075f100 RCX:
ffff8fed7fca7ed0
[ 48.420025] RDX:
0000000000000000 RSI:
000000000003440e RDI:
0000000022400000
[ 48.420073] RBP:
ffffb02101273c10 R08:
0000000000000010 R09:
ffff8fed7ffd3680
[ 48.420121] R10:
ffffeee1418ad7c0 R11:
ffff8fed7ffd3000 R12:
ffffffffc075e2c0
[ 48.420169] R13:
ffffffffc074ec10 R14:
ffff8fed73063900 R15:
ffff8fed737428e8
[ 48.420216] FS:
00007fdc912ec540(0000) GS:
ffff8fed7fc80000(0000) knlGS:
0000000000000000
[ 48.420267] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 48.420308] CR2:
000055fa40c30060 CR3:
000000023470a006 CR4:
00000000003606e0
[ 48.420358] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 48.420405] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 48.420452] Call Trace:
[ 48.420485] ttm_bo_global_kobj_release+0x20/0x30 [amdttm]
[ 48.420528] kobject_release+0x6a/0x180
[ 48.420562] kobject_put+0x28/0x50
[ 48.420595] ttm_bo_global_release+0x36/0x50 [amdttm]
[ 48.420636] amdttm_bo_device_release+0x119/0x180 [amdttm]
[ 48.420678] ? amdttm_bo_clean_mm+0xa6/0xf0 [amdttm]
[ 48.420760] amdgpu_ttm_fini+0xc9/0x180 [amdgpu]
[ 48.420821] amdgpu_bo_fini+0x12/0x40 [amdgpu]
[ 48.420889] gmc_v9_0_sw_fini+0x40/0x50 [amdgpu]
[ 48.420947] amdgpu_device_fini+0x36f/0x4c0 [amdgpu]
[ 48.421007] amdgpu_driver_unload_kms+0xb4/0x150 [amdgpu]
[ 48.421058] drm_dev_unregister+0x46/0xf0 [drm]
[ 48.421102] drm_dev_unplug+0x12/0x70 [drm]
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Sun, 14 Oct 2018 17:54:27 +0000 (19:54 +0200)]
platform/x86: Add Intel AtomISP2 dummy / power-management driver
[ Upstream commit
49ad712afa88c502831d37f7089d98eac441fb80 ]
The Image Signal Processor found on Cherry Trail devices is brought up in
D0 state on devices which have camera sensors attached to it. The ISP will
not enter D3 state again without some massaging of its registers beforehand
and the ISP not being in D3 state blocks the SoC from entering S0ix modes.
There was a driver for the ISP in drivers/staging but that got removed
again because it never worked. It does not seem likely that a real
driver for the ISP will be added to the mainline kernel anytime soon.
This commit adds a dummy driver which contains the necessary magic from
the staging driver to powerdown the ISP, so that Cherry Trail devices where
the ISP is used will properly use S0ix modes when suspended.
Together with other recent S0ix related fixes this allows S0ix modes to
be entered on e.g. a Chuwi Hi8 Pro and a HP x2 210.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196915
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vitaly Kuznetsov [Wed, 17 Oct 2018 11:23:55 +0000 (13:23 +0200)]
kernel: hung_task.c: disable on suspend
[ Upstream commit
a1c6ca3c6de763459a6e93b644ec6518c890ba1c ]
It is possible to observe hung_task complaints when system goes to
suspend-to-idle state:
# echo freeze > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
sd 0:0:0:0: [sda] Synchronizing SCSI cache
INFO: task bash:1569 blocked for more than 120 seconds.
Not tainted 4.19.0-rc3_+ #687
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
bash D 0 1569 604 0x00000000
Call Trace:
? __schedule+0x1fe/0x7e0
schedule+0x28/0x80
suspend_devices_and_enter+0x4ac/0x750
pm_suspend+0x2c0/0x310
Register a PM notifier to disable the detector on suspend and re-enable
back on wakeup.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steve French [Fri, 19 Oct 2018 06:58:22 +0000 (01:58 -0500)]
cifs: fallback to older infolevels on findfirst queryinfo retry
[ Upstream commit
3b7960caceafdfc2cdfe2850487f8d091eb41144 ]
In cases where queryinfo fails, we have cases in cifs (vers=1.0)
where with backupuid mounts we retry the query info with findfirst.
This doesn't work to some NetApp servers which don't support
WindowsXP (and later) infolevel 261 (SMB_FIND_FILE_ID_FULL_DIR_INFO)
so in this case use other info levels (in this case it will usually
be level 257, SMB_FIND_FILE_DIRECTORY_INFO).
(Also fixes some indentation)
See kernel bugzilla 201435
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thor Thayer [Mon, 22 Oct 2018 22:22:26 +0000 (17:22 -0500)]
net: stmmac: Set OWN bit for jumbo frames
[ Upstream commit
487e2e22ab7968f2c0c82f37b5ca5883efd1a354 ]
Ping with Jumbo packet does not reply and get a watchdog timeout
[ 46.059616] ------------[ cut here ]------------
[ 46.064268] NETDEV WATCHDOG: eth0 (socfpga-dwmac): transmit queue 0 timed out
[ 46.071471] WARNING: CPU: 1 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x2cc/0x2d8
[ 46.079708] Modules linked in:
[ 46.082761] CPU: 1 PID: 0 Comm: swapper/1 Not tainted
4.18.0-00115-gc262be665854-dirty #264
[ 46.091082] Hardware name: SoCFPGA Stratix 10 SoCDK (DT)
[ 46.096377] pstate:
20000005 (nzCv daif -PAN -UAO)
[ 46.101152] pc : dev_watchdog+0x2cc/0x2d8
[ 46.105149] lr : dev_watchdog+0x2cc/0x2d8
[ 46.109144] sp :
ffff00000800bd80
[ 46.112447] x29:
ffff00000800bd80 x28:
ffff80007a9b4940
[ 46.117744] x27:
00000000ffffffff x26:
ffff80007aa183b0
[ 46.123040] x25:
0000000000000001 x24:
0000000000000140
[ 46.128336] x23:
ffff80007aa1839c x22:
ffff80007aa17fb0
[ 46.133632] x21:
ffff80007aa18000 x20:
ffff0000091a7000
[ 46.138927] x19:
0000000000000000 x18:
ffffffffffffffff
[ 46.144223] x17:
0000000000000000 x16:
0000000000000000
[ 46.149519] x15:
ffff0000091a96c8 x14:
07740775076f0720
[ 46.154814] x13:
07640765076d0769 x12:
0774072007300720
[ 46.160110] x11:
0765077507650775 x10:
0771072007740769
[ 46.165406] x9 :
076d0773076e0761 x8 :
077207740720073a
[ 46.170702] x7 :
072907630761076d x6 :
ffff80007ff9a0c0
[ 46.175997] x5 :
ffff80007ff9a0c0 x4 :
0000000000000002
[ 46.181293] x3 :
0000000000000000 x2 :
ffff0000091ac180
[ 46.186589] x1 :
e6a742ebe628e800 x0 :
0000000000000000
[ 46.191885] Call trace:
[ 46.194326] dev_watchdog+0x2cc/0x2d8
[ 46.197980] call_timer_fn+0x20/0x78
[ 46.201544] expire_timers+0xa4/0xb0
[ 46.205108] run_timer_softirq+0xe4/0x198
[ 46.209107] __do_softirq+0x114/0x210
[ 46.212760] irq_exit+0xd0/0xd8
[ 46.215895] __handle_domain_irq+0x60/0xb0
[ 46.219977] gic_handle_irq+0x58/0xa8
[ 46.223628] el1_irq+0xb0/0x128
[ 46.226761] arch_cpu_idle+0x10/0x18
[ 46.230326] do_idle+0x1d4/0x288
[ 46.233544] cpu_startup_entry+0x24/0x28
[ 46.237457] secondary_start_kernel+0x17c/0x1c0
[ 46.241971] ---[ end trace
57048cd1372cd828 ]---
Inspection of queue showed Jumbo packets were not sent out.
The ring Jumbo packet function needs to set the OWN bit so
the packet is sent.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sheng Yong [Fri, 12 Oct 2018 10:49:26 +0000 (18:49 +0800)]
f2fs: cleanup dirty pages if recover failed
[ Upstream commit
26b5a079197c8cb6725565968b7fd3299bd1877b ]
During recover, we will try to create new dentries for inodes with
dentry_mark. But if the parent is missing (e.g. killed by fsck),
recover will break. But those recovered dirty pages are not cleanup.
This will hit f2fs_bug_on:
[ 53.519566] F2FS-fs (loop0): Found nat_bits in checkpoint
[ 53.539354] F2FS-fs (loop0): recover_inode: ino = 5, name = file, inline = 3
[ 53.539402] F2FS-fs (loop0): recover_dentry: ino = 5, name = file, dir = 0, err = -2
[ 53.545760] F2FS-fs (loop0): Cannot recover all fsync data errno=-2
[ 53.546105] F2FS-fs (loop0): access invalid blkaddr:
4294967295
[ 53.546171] WARNING: CPU: 1 PID: 1798 at fs/f2fs/checkpoint.c:163 f2fs_is_valid_blkaddr+0x26c/0x320
[ 53.546174] Modules linked in:
[ 53.546183] CPU: 1 PID: 1798 Comm: mount Not tainted 4.19.0-rc2+ #1
[ 53.546186] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 53.546191] RIP: 0010:f2fs_is_valid_blkaddr+0x26c/0x320
[ 53.546195] Code: 85 bb 00 00 00 48 89 df 88 44 24 07 e8 ad a8 db ff 48 8b 3b 44 89 e1 48 c7 c2 40 03 72 a9 48 c7 c6 e0 01 72 a9 e8 84 3c ff ff <0f> 0b 0f b6 44 24 07 e9 8a 00 00 00 48 8d bf 38 01 00 00 e8 7c a8
[ 53.546201] RSP: 0018:
ffff88006c067768 EFLAGS:
00010282
[ 53.546208] RAX:
0000000000000000 RBX:
ffff880068844200 RCX:
ffffffffa83e1a33
[ 53.546211] RDX:
0000000000000000 RSI:
0000000000000008 RDI:
ffff88006d51e590
[ 53.546215] RBP:
0000000000000005 R08:
ffffed000daa3cb3 R09:
ffffed000daa3cb3
[ 53.546218] R10:
0000000000000001 R11:
ffffed000daa3cb2 R12:
00000000ffffffff
[ 53.546221] R13:
ffff88006a1f8000 R14:
0000000000000200 R15:
0000000000000009
[ 53.546226] FS:
00007fb2f3646840(0000) GS:
ffff88006d500000(0000) knlGS:
0000000000000000
[ 53.546229] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 53.546234] CR2:
00007f0fd77f0008 CR3:
00000000687e6002 CR4:
00000000000206e0
[ 53.546237] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 53.546240] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 53.546242] Call Trace:
[ 53.546248] f2fs_submit_page_bio+0x95/0x740
[ 53.546253] read_node_page+0x161/0x1e0
[ 53.546271] ? truncate_node+0x650/0x650
[ 53.546283] ? add_to_page_cache_lru+0x12c/0x170
[ 53.546288] ? pagecache_get_page+0x262/0x2d0
[ 53.546292] __get_node_page+0x200/0x660
[ 53.546302] f2fs_update_inode_page+0x4a/0x160
[ 53.546306] f2fs_write_inode+0x86/0xb0
[ 53.546317] __writeback_single_inode+0x49c/0x620
[ 53.546322] writeback_single_inode+0xe4/0x1e0
[ 53.546326] sync_inode_metadata+0x93/0xd0
[ 53.546330] ? sync_inode+0x10/0x10
[ 53.546342] ? do_raw_spin_unlock+0xed/0x100
[ 53.546347] f2fs_sync_inode_meta+0xe0/0x130
[ 53.546351] f2fs_fill_super+0x287d/0x2d10
[ 53.546367] ? vsnprintf+0x742/0x7a0
[ 53.546372] ? f2fs_commit_super+0x180/0x180
[ 53.546379] ? up_write+0x20/0x40
[ 53.546385] ? set_blocksize+0x5f/0x140
[ 53.546391] ? f2fs_commit_super+0x180/0x180
[ 53.546402] mount_bdev+0x181/0x200
[ 53.546406] mount_fs+0x94/0x180
[ 53.546411] vfs_kern_mount+0x6c/0x1e0
[ 53.546415] do_mount+0xe5e/0x1510
[ 53.546420] ? fs_reclaim_release+0x9/0x30
[ 53.546424] ? copy_mount_string+0x20/0x20
[ 53.546428] ? fs_reclaim_acquire+0xd/0x30
[ 53.546435] ? __might_sleep+0x2c/0xc0
[ 53.546440] ? ___might_sleep+0x53/0x170
[ 53.546453] ? __might_fault+0x4c/0x60
[ 53.546468] ? _copy_from_user+0x95/0xa0
[ 53.546474] ? memdup_user+0x39/0x60
[ 53.546478] ksys_mount+0x88/0xb0
[ 53.546482] __x64_sys_mount+0x5d/0x70
[ 53.546495] do_syscall_64+0x65/0x130
[ 53.546503] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.547639] ---[ end trace
b804d1ea2fec893e ]---
So if recover fails, we need to drop all recovered data.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Taehee Yoo [Mon, 1 Oct 2018 17:17:14 +0000 (02:17 +0900)]
netfilter: nf_flow_table: remove flowtable hook flush routine in netns exit routine
[ Upstream commit
b7f1a16d29b2e28d3dcbb070511bd703e306281b ]
When device is unregistered, flowtable flush routine is called
by notifier_call(nf_tables_flowtable_event). and exit callback of
nftables pernet_operation(nf_tables_exit_net) also has flowtable flush
routine. but when network namespace is destroyed, both notifier_call
and pernet_operation are called. hence flowtable flush routine in
pernet_operation is unnecessary.
test commands:
%ip netns add vm1
%ip netns exec vm1 nft add table ip filter
%ip netns exec vm1 nft add flowtable ip filter w \
{ hook ingress priority 0\; devices = { lo }\; }
%ip netns del vm1
splat looks like:
[ 265.187019] WARNING: CPU: 0 PID: 87 at net/netfilter/core.c:309 nf_hook_entry_head+0xc7/0xf0
[ 265.187112] Modules linked in: nf_flow_table_ipv4 nf_flow_table nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables nfnetlink ip_tables x_tables
[ 265.187390] CPU: 0 PID: 87 Comm: kworker/u4:2 Not tainted 4.19.0-rc3+ #5
[ 265.187453] Workqueue: netns cleanup_net
[ 265.187514] RIP: 0010:nf_hook_entry_head+0xc7/0xf0
[ 265.187546] Code: 8d 81 68 03 00 00 5b c3 89 d0 83 fa 04 48 8d 84 c7 e8 11 00 00 76 81 0f 0b 31 c0 e9 78 ff ff ff 0f 0b 48 83 c4 08 31 c0 5b c3 <0f> 0b 31 c0 e9 65 ff ff ff 0f 0b 31 c0 e9 5c ff ff ff 48 89 0c 24
[ 265.187573] RSP: 0018:
ffff88011546f098 EFLAGS:
00010246
[ 265.187624] RAX:
ffffffff8d90e135 RBX:
1ffff10022a8de1c RCX:
0000000000000000
[ 265.187645] RDX:
0000000000000000 RSI:
0000000000000005 RDI:
ffff880116298040
[ 265.187645] RBP:
ffff88010ea4c1a8 R08:
0000000000000000 R09:
0000000000000000
[ 265.187645] R10:
ffff88011546f1d8 R11:
ffffed0022c532c1 R12:
ffff88010ea4c1d0
[ 265.187645] R13:
0000000000000005 R14:
dffffc0000000000 R15:
ffff88010ea4c1c4
[ 265.187645] FS:
0000000000000000(0000) GS:
ffff88011b200000(0000) knlGS:
0000000000000000
[ 265.187645] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 265.187645] CR2:
00007fdfb8d00000 CR3:
0000000057a16000 CR4:
00000000001006f0
[ 265.187645] Call Trace:
[ 265.187645] __nf_unregister_net_hook+0xca/0x5d0
[ 265.187645] ? nf_hook_entries_free.part.3+0x80/0x80
[ 265.187645] ? save_trace+0x300/0x300
[ 265.187645] nf_unregister_net_hooks+0x2e/0x40
[ 265.187645] nf_tables_exit_net+0x479/0x1340 [nf_tables]
[ 265.187645] ? find_held_lock+0x39/0x1c0
[ 265.187645] ? nf_tables_abort+0x30/0x30 [nf_tables]
[ 265.187645] ? inet_frag_destroy_rcu+0xd0/0xd0
[ 265.187645] ? trace_hardirqs_on+0x93/0x210
[ 265.187645] ? __bpf_trace_preemptirq_template+0x10/0x10
[ 265.187645] ? inet_frag_destroy_rcu+0xd0/0xd0
[ 265.187645] ? inet_frag_destroy_rcu+0xd0/0xd0
[ 265.187645] ? __mutex_unlock_slowpath+0x17f/0x740
[ 265.187645] ? wait_for_completion+0x710/0x710
[ 265.187645] ? bucket_table_free+0xb2/0x1f0
[ 265.187645] ? nested_table_free+0x130/0x130
[ 265.187645] ? __lock_is_held+0xb4/0x140
[ 265.187645] ops_exit_list.isra.10+0x94/0x140
[ 265.187645] cleanup_net+0x45b/0x900
[ ... ]
This WARNING means that hook unregisteration is failed because
all flowtables hooks are already unregistered by notifier_call.
Network namespace exit routine guarantees that all devices will be
unregistered first. then, other exit callbacks of pernet_operations
are called. so that removing flowtable flush routine in exit callback of
pernet_operation(nf_tables_exit_net) doesn't make flowtable leak.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ndesaulniers@google.com [Mon, 15 Oct 2018 17:22:21 +0000 (10:22 -0700)]
compiler.h: update definition of unreachable()
[ Upstream commit
fe0640eb30b7da261ae84d252ed9ed3c7e68dfd8 ]
Fixes the objtool warning seen with Clang:
arch/x86/mm/fault.o: warning: objtool: no_context()+0x220: unreachable
instruction
Fixes commit
815f0ddb346c ("include/linux/compiler*.h: make compiler-*.h
mutually exclusive")
Josh noted that the fallback definition was meant to work around a
pre-gcc-4.6 bug. GCC still needs to work around
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365, so compiler-gcc.h
defines its own version of unreachable(). Clang and ICC can use this
shared definition.
Link: https://github.com/ClangBuiltLinux/linux/issues/204
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>