OSDN Git Service
Guillaume Nault [Wed, 7 Sep 2016 15:21:40 +0000 (17:21 +0200)]
ipv6: report NLM_F_CREATE and NLM_F_EXCL flags in RTM_NEWROUTE events
Since commit
37a1d3611c12 ("ipv6: include NLM_F_REPLACE in route
replace notifications"), RTM_NEWROUTE notifications have their
NLM_F_REPLACE flag set if the new route replaced a preexisting one.
However, other flags aren't set.
This patch reports the missing NLM_F_CREATE and NLM_F_EXCL flag bits.
NLM_F_APPEND is not reported, because in ipv6 a NLM_F_CREATE request
is interpreted as an append request (contrary to ipv4, "prepend" is not
supported, so if NLM_F_EXCL is not set then NLM_F_APPEND is implicit).
As a result, the possible flag combination can now be reported
(iproute2's terminology into parentheses):
* NLM_F_CREATE | NLM_F_EXCL: route didn't exist, exclusive creation
("add").
* NLM_F_CREATE: route did already exist, new route added after
preexisting ones ("append").
* NLM_F_REPLACE: route did already exist, new route replaced the
first preexisting one ("change").
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Wed, 7 Sep 2016 15:20:46 +0000 (17:20 +0200)]
ipv4: fix value of ->nlmsg_flags reported in RTM_NEWROUTE events
fib_table_insert() inconsistently fills the nlmsg_flags field in its
notification messages.
Since commit
b8f558313506 ("[RTNETLINK]: Fix sending netlink message
when replace route."), the netlink message has its nlmsg_flags set to
NLM_F_REPLACE if the route replaced a preexisting one.
Then commit
a2bb6d7d6f42 ("ipv4: include NLM_F_APPEND flag in append
route notifications") started setting nlmsg_flags to NLM_F_APPEND if
the route matched a preexisting one but was appended.
In other cases (exclusive creation or prepend), nlmsg_flags is 0.
This patch sets ->nlmsg_flags in all situations, preserving the
semantic of the NLM_F_* bits:
* NLM_F_CREATE: a new fib entry has been created for this route.
* NLM_F_EXCL: no other fib entry existed for this route.
* NLM_F_REPLACE: this route has overwritten a preexisting fib entry.
* NLM_F_APPEND: the new fib entry was added after other entries for
the same route.
As a result, the possible flag combination can now be reported
(iproute2's terminology into parentheses):
* NLM_F_CREATE | NLM_F_EXCL: route didn't exist, exclusive creation
("add").
* NLM_F_CREATE | NLM_F_APPEND: route did already exist, new route
added after preexisting ones ("append").
* NLM_F_CREATE: route did already exist, new route added before
preexisting ones ("prepend").
* NLM_F_REPLACE: route did already exist, new route replaced the
first preexisting one ("change").
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Sep 2016 04:52:56 +0000 (21:52 -0700)]
ipv4: accept u8 in IP_TOS ancillary data
In commit
f02db315b8d8 ("ipv4: IP_TOS and IP_TTL can be specified as
ancillary data") Francesco added IP_TOS values specified as integer.
However, kernel sends to userspace (at recvmsg() time) an IP_TOS value
in a single byte, when IP_RECVTOS is set on the socket.
It can be very useful to reflect all ancillary options as given by the
kernel in a subsequent sendmsg(), instead of aborting the sendmsg() with
EINVAL after Francesco patch.
So this patch extends IP_TOS ancillary to accept an u8, so that an UDP
server can simply reuse same ancillary block without having to mangle
it.
Jesper can then augment
https://github.com/netoptimizer/network-testing/blob/master/src/udp_example02.c
to add TOS reflection ;)
Fixes:
f02db315b8d8 ("ipv4: IP_TOS and IP_TTL can be specified as ancillary data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Francesco Fusco <ffusco@redhat.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 7 Sep 2016 23:03:42 +0000 (01:03 +0200)]
bpf: fix range propagation on direct packet access
LLVM can generate code that tests for direct packet access via
skb->data/data_end in a way that currently gets rejected by the
verifier, example:
[...]
7: (61) r3 = *(u32 *)(r6 +80)
8: (61) r9 = *(u32 *)(r6 +76)
9: (bf) r2 = r9
10: (07) r2 += 54
11: (3d) if r3 >= r2 goto pc+12
R1=inv R2=pkt(id=0,off=54,r=0) R3=pkt_end R4=inv R6=ctx
R9=pkt(id=0,off=0,r=0) R10=fp
12: (18) r4 = 0xffffff7a
14: (05) goto pc+430
[...]
from 11 to 24: R1=inv R2=pkt(id=0,off=54,r=0) R3=pkt_end R4=inv
R6=ctx R9=pkt(id=0,off=0,r=0) R10=fp
24: (7b) *(u64 *)(r10 -40) = r1
25: (b7) r1 = 0
26: (63) *(u32 *)(r6 +56) = r1
27: (b7) r2 = 40
28: (71) r8 = *(u8 *)(r9 +20)
invalid access to packet, off=20 size=1, R9(id=0,off=0,r=0)
The reason why this gets rejected despite a proper test is that we
currently call find_good_pkt_pointers() only in case where we detect
tests like rX > pkt_end, where rX is of type pkt(id=Y,off=Z,r=0) and
derived, for example, from a register of type pkt(id=Y,off=0,r=0)
pointing to skb->data. find_good_pkt_pointers() then fills the range
in the current branch to pkt(id=Y,off=0,r=Z) on success.
For above case, we need to extend that to recognize pkt_end >= rX
pattern and mark the other branch that is taken on success with the
appropriate pkt(id=Y,off=0,r=Z) type via find_good_pkt_pointers().
Since eBPF operates on BPF_JGT (>) and BPF_JGE (>=), these are the
only two practical options to test for from what LLVM could have
generated, since there's no such thing as BPF_JLT (<) or BPF_JLE (<=)
that we would need to take into account as well.
After the fix:
[...]
7: (61) r3 = *(u32 *)(r6 +80)
8: (61) r9 = *(u32 *)(r6 +76)
9: (bf) r2 = r9
10: (07) r2 += 54
11: (3d) if r3 >= r2 goto pc+12
R1=inv R2=pkt(id=0,off=54,r=0) R3=pkt_end R4=inv R6=ctx
R9=pkt(id=0,off=0,r=0) R10=fp
12: (18) r4 = 0xffffff7a
14: (05) goto pc+430
[...]
from 11 to 24: R1=inv R2=pkt(id=0,off=54,r=54) R3=pkt_end R4=inv
R6=ctx R9=pkt(id=0,off=0,r=54) R10=fp
24: (7b) *(u64 *)(r10 -40) = r1
25: (b7) r1 = 0
26: (63) *(u32 *)(r6 +56) = r1
27: (b7) r2 = 40
28: (71) r8 = *(u8 *)(r9 +20)
29: (bf) r1 = r8
30: (25) if r8 > 0x3c goto pc+47
R1=inv56 R2=imm40 R3=pkt_end R4=inv R6=ctx R8=inv56
R9=pkt(id=0,off=0,r=54) R10=fp
31: (b7) r1 = 1
[...]
Verifier test cases are also added in this work, one that demonstrates
the mentioned example here and one that tries a bad packet access for
the current/fall-through branch (the one with types pkt(id=X,off=Y,r=0),
pkt(id=X,off=0,r=0)), then a case with good and bad accesses, and two
with both test variants (>, >=).
Fixes:
969bf05eb3ce ("bpf: direct packet access")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yaogong Wang [Wed, 7 Sep 2016 21:49:28 +0000 (14:49 -0700)]
tcp: use an RB tree for ooo receive queue
Over the years, TCP BDP has increased by several orders of magnitude,
and some people are considering to reach the 2 Gbytes limit.
Even with current window scale limit of 14, ~1 Gbytes maps to ~740,000
MSS.
In presence of packet losses (or reorders), TCP stores incoming packets
into an out of order queue, and number of skbs sitting there waiting for
the missing packets to be received can be in the 10^5 range.
Most packets are appended to the tail of this queue, and when
packets can finally be transferred to receive queue, we scan the queue
from its head.
However, in presence of heavy losses, we might have to find an arbitrary
point in this queue, involving a linear scan for every incoming packet,
throwing away cpu caches.
This patch converts it to a RB tree, to get bounded latencies.
Yaogong wrote a preliminary patch about 2 years ago.
Eric did the rebase, added ofo_last_skb cache, polishing and tests.
Tested with network dropping between 1 and 10 % packets, with good
success (about 30 % increase of throughput in stress tests)
Next step would be to also use an RB tree for the write queue at sender
side ;)
Signed-off-by: Yaogong Wang <wygivan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-By: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Sep 2016 00:10:28 +0000 (17:10 -0700)]
Merge branch 'ovs-802.1ad'
Eric Garver says:
====================
openvswitch: add 802.1ad support
This series adds 802.1ad support to openvswitch. It is a continuation of the
work originally started by Thomas F Herbert - hence the large rev number.
The extra VLAN is implemented by using an additional level of the
OVS_KEY_ATTR_ENCAP netlink attribute.
In OVS flow speak, this looks like
eth_type(0x88a8),vlan(vid=100),encap(eth_type(0x8100), vlan(vid=200),
encap(eth_type(0x0800), ...))
The userspace counterpart has also seen recent activity on the ovs-dev mailing
lists. There are some new 802.1ad OVS tests being added - also on the ovs-dev
list. This patch series has been tested using the most recent version of
userspace (v3) and tests (v2).
v22 changes:
- merge patch 4 into patch 3
- fix checkpatch.pl errors
- Still some 80 char warnings for long string literals
- refresh pointer after pskb_may_pull()
- refactor vlan nlattr parsing to remove some double checks
- introduce ovs_nla_put_vlan()
- move triple VLAN check to after ethertype serialization
- WARN_ON_ONCE() on triple VLAN and unexpected encap values
v21 changes:
- Fix (and simplify) netlink attribute parsing
- re-add handling of truncated VLAN tags
- fix if/else dangling assignment in {push,pop}_vlan()
- simplify parse_vlan()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Garver [Wed, 7 Sep 2016 16:56:59 +0000 (12:56 -0400)]
openvswitch: 802.1AD Flow handling, actions, vlan parsing, netlink attributes
Add support for 802.1ad including the ability to push and pop double
tagged vlans. Add support for 802.1ad to netlink parsing and flow
conversion. Uses double nested encap attributes to represent double
tagged vlan. Inner TPID encoded along with ctci in nested attributes.
This is based on Thomas F Herbert's original v20 patch. I made some
small clean ups and bug fixes.
Signed-off-by: Thomas F Herbert <thomasfherbert@gmail.com>
Signed-off-by: Eric Garver <e@erig.me>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Garver [Wed, 7 Sep 2016 16:56:58 +0000 (12:56 -0400)]
vlan: Check for vlan ethernet types for 8021.q or 802.1ad
This is to simplify using double tagged vlans. This function allows all
valid vlan ethertypes to be checked in a single function call.
Also replace some instances that check for both ETH_P_8021Q and
ETH_P_8021AD.
Patch based on one originally by Thomas F Herbert.
Signed-off-by: Thomas F Herbert <thomasfherbert@gmail.com>
Signed-off-by: Eric Garver <e@erig.me>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas F Herbert [Wed, 7 Sep 2016 16:56:57 +0000 (12:56 -0400)]
openvswitch: 802.1ad uapi changes.
openvswitch: Add support for 8021.AD
Change the description of the VLAN tpid field.
Signed-off-by: Thomas F Herbert <thomasfherbert@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Colitti [Wed, 7 Sep 2016 15:42:25 +0000 (00:42 +0900)]
net: inet: diag: expose the socket mark to privileged processes.
This adds the capability for a process that has CAP_NET_ADMIN on
a socket to see the socket mark in socket dumps.
Commit
a52e95abf772 ("net: diag: allow socket bytecode filters to
match socket marks") recently gave privileged processes the
ability to filter socket dumps based on mark. This patch is
complementary: it ensures that the mark is also passed to
userspace in the socket's netlink attributes. It is useful for
tools like ss which display information about sockets.
Tested: https://android-review.googlesource.com/270210
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zubair Lutfullah Kakakhel [Mon, 5 Sep 2016 12:07:54 +0000 (13:07 +0100)]
net: ethernet: xilinx: Enable emaclite for MIPS
The MIPS based xilfpga platform uses this driver.
Enable it for MIPS
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Sep 2016 20:09:41 +0000 (13:09 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
ipsec-next 2016-09-08
1) Constify the xfrm_replay structures. From Julia Lawall
2) Protect xfrm state hash tables with rcu, lookups
can be done now without acquiring xfrm_state_lock.
From Florian Westphal.
3) Protect xfrm policy hash tables with rcu, lookups
can be done now without acquiring xfrm_policy_lock.
From Florian Westphal.
4) We don't need to have a garbage collector list per
namespace anymore, so use a global one instead.
From Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
subashab@codeaurora.org [Wed, 7 Sep 2016 00:09:31 +0000 (18:09 -0600)]
net: xfrm: Change u32 sysctl entries to use proc_douintvec
proc_dointvec limits the values to INT_MAX in u32 sysctl entries.
proc_douintvec allows to write upto UINT_MAX.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Sep 2016 05:44:56 +0000 (22:44 -0700)]
Merge branch 'be2net-error-recovery-and-bug-fixes'
Sriharsha Basavapatna says:
====================
be2net: patch-set
The following patch set contains an error recovery feature and a few
bug fixes. Please consider applying this to the net-next tree. Thanks.
Patch-1 Supports HW error recovery in Skyhawk/BEx adapters
Patch-2 Fixes driver unload to issue function reset FW command
Patch-3 Avoids issuing GET_EXT_FAT_CAPABILITIES command for VFs
Patch-4 Avoids redundant addition of mac address in HW
Patch-5 Fixes mac address collision in some configurations
Patch-6 Updates driver version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sriharsha Basavapatna [Wed, 7 Sep 2016 14:27:54 +0000 (19:57 +0530)]
be2net: Update the driver version to 11.1.0.0
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy [Wed, 7 Sep 2016 14:27:53 +0000 (19:57 +0530)]
be2net: Fix mac address collision in some configurations
If the device mac address is updated using ndo_set_mac_address(),
while the same mac address is already programmed, the driver does not
detect this condition if its netdev->dev_addr has been changed. The
driver tries to add the same mac address resulting in mac address
collision error. This has been observed in bonding mode-5 configuration.
To fix this, store the mac address configured in HW in the adapter
structure. Use this to compare against the new address being updated
to avoid collision.
Signed-off-by: Suresh Reddy <Suresh.Reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh Reddy [Wed, 7 Sep 2016 14:27:52 +0000 (19:57 +0530)]
be2net: Avoid redundant addition of mac address in HW
If a mac address is added to the uc_list and later the same mac address
is added via ndo_set_mac_address() or vice versa, the driver does not
detect this condition and tries to add it again. This results in a mac
address collision error when the FW rejects it.
Fix this by checking if the given mac address is present in uc_list while
setting the device mac address and vice versa. Similarly skip deletion if
the address is still in use in the other form.
Signed-off-by: Suresh Reddy <Suresh.Reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Wed, 7 Sep 2016 14:27:51 +0000 (19:57 +0530)]
be2net: Add privilege level check for OPCODE_COMMON_GET_EXT_FAT_CAPABILITIES SLI cmd.
Driver issues OPCODE_COMMON_GET_EXT_FAT_CAPABILITIES cmd during init which
when issued by VFs results in the logging of a cmd failure message since
they don't have the required privilege for this cmd. Fix by checking
privilege before issuing the cmd.
Also fixed typo in CAPABILITIES.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Wed, 7 Sep 2016 14:27:50 +0000 (19:57 +0530)]
be2net: Issue COMMON_RESET_FUNCTION cmd during driver unload
As per SLI guideline, drivers need to issue COMMON_RESET_FUNCTION SLI
cmd during driver unload to clean up any non-persistent state
information.
Issue this cmd only if VFs are not assigned to VMs as it is possible
for PF driver to unload while it\'s VF remains functional and assigned
to a VM.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sriharsha Basavapatna [Wed, 7 Sep 2016 14:27:49 +0000 (19:57 +0530)]
be2net: Support UE recovery in BEx/Skyhawk adapters
This patch supports recovery from UEs caused due to Transient Parity
Errors (TPE), in BE2, BE3 and Skyhawk adapters. This change avoids
system reboot when such errors occur. The driver recovers from these
errors such that the adapter resumes full operational status as prior
to the UE.
Following is the list of changes in the driver to support this:
o The driver registers its UE recoverable capability with ARM FW at init
time. This also allows the driver to know if the feature is supported in
the FW.
o As the UE recovery requires precise time bound processing, the driver
creates its own error recovery work queue with a single worker thread (per
module, shared across functions).
o Each function runs an error detection task at an interval of 1 second as
required by the FW. The error detection logic already exists for BEx/SH,
but it now runs in the context of a separate worker thread.
o When an error is detected by the task, if it is recoverable, the PF0
driver instance initiates a soft reset, while other PF driver instances
wait for the reset to complete and the chip to become ready. Once
the chip is ready, all driver instances including PF0, resume to
reinitialize the respective functions.
o The PF0 driver checks for some recovery criteria, to determine if the
recovery can be initiated. If the criteria is not met, the PF0 driver does
not initiate a soft reset, it retains the existing behavior to stop
further processing and requires a reboot to get the chip to operational
state again.
o To allow each function to share the workq, while also making progress in
its recovery process, a per-function recovery state machine is used.
The per-function tasks avoid blocking operations like msleep() while in
this state machine (until reinit state) and instead reschedule for the
required delay.
o With these changes, the existing error recovery code for Lancer also
runs in the context of the new worker thread.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Wed, 7 Sep 2016 13:53:42 +0000 (15:53 +0200)]
net: smsc911x: request and deassert optional RESET GPIO
On some systems (such as the Qualcomm APQ8060 Dragonboard) the
RESET signal of the SMSC911x is not pulled up by a resistor (or
the internal pull-up that will pull it up if the pin is not
even connected) but instead connected to a GPIO line, so that
the operating system must explicitly deassert RESET before use.
Support this in the SMSC911x driver so this ethernet connector
can be used on such targets.
Notice that we request the line to go logical low (deassert)
whilst the line on the actual component is active low. This
is managed in the respective hardware description when
specifying the GPIO line with e.g. device tree or ACPI. With
device tree it looks like this in one case:
reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
Which means that logically requesting the RESET line to be
deasserted will result in the line being driven high, taking
the device out of reset.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Wed, 7 Sep 2016 13:53:31 +0000 (15:53 +0200)]
net: smsc911x: augment device tree bindings
This adds device tree bindings for:
- An optional GPIO line for releasing the RESET signal to the
SMSC911x devices
- An optional PME (power management event) interrupt line that
can be utilized to wake up the system on network activity.
This signal exist on all the SMSC911x devices, it is just not
very often routed.
Both these lines are routed to the SoC on the Qualcomm APQ8060
Dragonboard and thus needs to be bound in the device tree.
Cc: devicetree@vger.kernel.org
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Sep 2016 00:47:00 +0000 (17:47 -0700)]
Merge branch 'qed-debug-data-collection'
Tomer Tayar says:
====================
qed*: Debug data collection
This patch series adds the support of debug data collection in the qed driver,
and the means to extract it in the qede driver via the get_regs operation.
Changes from V1:
- Respin of the series after rebasing next-next.
- Remove the first patch as it seems that its V1 version was already applied
(commit '
4102426f9b7b3627c8c23a54d70363e81c93f9b7').
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Wed, 7 Sep 2016 13:36:25 +0000 (16:36 +0300)]
qed*: Add support for the ethtool get_regs operation
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomer Tayar [Wed, 7 Sep 2016 13:36:24 +0000 (16:36 +0300)]
qed: Add support for debug data collection
This patch adds the support for dumping and formatting the HW/FW debug data.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Wed, 7 Sep 2016 13:27:09 +0000 (15:27 +0200)]
kaweth: remove obsolete debugging statements
SOme statements in the driver only served to inform
which functions were entered. Ftrace can do that just as good without
needing memory. Remove the statements.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baoyou Xie [Wed, 7 Sep 2016 11:07:00 +0000 (19:07 +0800)]
qed: add missing header dependencies
We get 4 warnings when building kernel with W=1:
drivers/net/ethernet/qlogic/qed/qed_selftest.c:6:5: warning: no previous prototype for 'qed_selftest_memory' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:19:5: warning: no previous prototype for 'qed_selftest_interrupt' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:32:5: warning: no previous prototype for 'qed_selftest_register' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_selftest.c:55:5: warning: no previous prototype for 'qed_selftest_clock' [-Wmissing-prototypes]
In fact, these functions are declared in qed_selftest.h, so this patch
add missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Colitti [Wed, 7 Sep 2016 04:38:35 +0000 (13:38 +0900)]
net: diag: make udp_diag_destroy work for mapped addresses.
udp_diag_destroy does look up the IPv4 UDP hashtable for mapped
addresses, but it gets the IPv4 address to look up from the
beginning of the IPv6 address instead of the end.
Tested: https://android-review.googlesource.com/269874
Fixes:
5d77dca82839 ("net: diag: support SOCK_DESTROY for UDP sockets")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Vagin [Wed, 7 Sep 2016 04:31:17 +0000 (21:31 -0700)]
netlink: don't forget to release a rhashtable_iter structure
This bug was detected by kmemleak:
unreferenced object 0xffff8804269cc3c0 (size 64):
comm "criu", pid 1042, jiffies
4294907360 (age 13.713s)
hex dump (first 32 bytes):
a0 32 cc 2c 04 88 ff ff 00 00 00 00 00 00 00 00 .2.,............
00 01 00 00 00 00 ad de 00 02 00 00 00 00 ad de ................
backtrace:
[<
ffffffff8184dffa>] kmemleak_alloc+0x4a/0xa0
[<
ffffffff8124720f>] kmem_cache_alloc_trace+0x10f/0x280
[<
ffffffffa02864cc>] __netlink_diag_dump+0x26c/0x290 [netlink_diag]
v2: don't remove a reference on a rhashtable_iter structure to
release it from netlink_diag_dump_done
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Fixes:
ad202074320c ("netlink: Use rhashtable walk interface in diag dump")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Sep 2016 00:21:56 +0000 (17:21 -0700)]
Merge tag 'rxrpc-rewrite-
20160907-2' of git://git./linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Local abort tracepoint
Here are two patches. They need to be applied on top of the just-posted
call refcount overhaul patch:
(1) Fix the return value of some call completion helpers.
(2) Add a tracepoint that allows local aborts to be debugged.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Sep 2016 00:20:23 +0000 (17:20 -0700)]
Merge tag 'rxrpc-rewrite-
20160907-1' of git://git./linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Overhaul call refcounting
Here's a set of mostly small patches leading up to one big one.
The big patch at the end of the series overhauls how rxrpc_call refcounting
is handled, making it more sane so that calls bound to user IDs are _only_
released from socket operations or kernel API functions. Further, the
patch stops calls from holding refs on their parent socket - which can
prevent the socket from being cleaned up.
The second largest patch improves the call tracking tracepoint by providing
extra information about the situation in which gets and puts occur. This
allows distinctions to be drawn between refs held by the socket user ID
tree, refs held by the work queue (to be implemented by a future patch) and
other refs.
The other patches include a couple of cleanups and some simple alterations
to avoid NULL pointer dereferences in the big patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Tue, 6 Sep 2016 21:19:51 +0000 (22:19 +0100)]
rxrpc: Add tracepoint for working out where aborts happen
Add a tracepoint for working out where local aborts happen. Each
tracepoint call is labelled with a 3-letter code so that they can be
distinguished - and the DATA sequence number is added too where available.
rxrpc_kernel_abort_call() also takes a 3-letter code so that AFS can
indicate the circumstances when it aborts a call.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 7 Sep 2016 15:34:12 +0000 (16:34 +0100)]
rxrpc: Fix returns of call completion helpers
rxrpc_set_call_completion() returns bool, not int, so the ret variable
should match this.
rxrpc_call_completed() and __rxrpc_call_completed() should return the value
of rxrpc_set_call_completion().
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 7 Sep 2016 08:19:31 +0000 (09:19 +0100)]
rxrpc: Calls shouldn't hold socket refs
rxrpc calls shouldn't hold refs on the sock struct. This was done so that
the socket wouldn't go away whilst the call was in progress, such that the
call could reach the socket's queues.
However, we can mark the socket as requiring an RCU release and rely on the
RCU read lock.
To make this work, we do:
(1) rxrpc_release_call() removes the call's call user ID. This is now
only called from socket operations and not from the call processor:
rxrpc_accept_call() / rxrpc_kernel_accept_call()
rxrpc_reject_call() / rxrpc_kernel_reject_call()
rxrpc_kernel_end_call()
rxrpc_release_calls_on_socket()
rxrpc_recvmsg()
Though it is also called in the cleanup path of
rxrpc_accept_incoming_call() before we assign a user ID.
(2) Pass the socket pointer into rxrpc_release_call() rather than getting
it from the call so that we can get rid of uninitialised calls.
(3) Fix call processor queueing to pass a ref to the work queue and to
release that ref at the end of the processor function (or to pass it
back to the work queue if we have to requeue).
(4) Skip out of the call processor function asap if the call is complete
and don't requeue it if the call is complete.
(5) Clean up the call immediately that the refcount reaches 0 rather than
trying to defer it. Actual deallocation is deferred to RCU, however.
(6) Don't hold socket refs for allocated calls.
(7) Use the RCU read lock when queueing a message on a socket and treat
the call's socket pointer according to RCU rules and check it for
NULL.
We also need to use the RCU read lock when viewing a call through
procfs.
(8) Transmit the final ACK/ABORT to a client call in rxrpc_release_call()
if this hasn't been done yet so that we can then disconnect the call.
Once the call is disconnected, it won't have any access to the
connection struct and the UDP socket for the call work processor to be
able to send the ACK. Terminal retransmission will be handled by the
connection processor.
(9) Release all calls immediately on the closing of a socket rather than
trying to defer this. Incomplete calls will be aborted.
The call refcount model is much simplified. Refs are held on the call by:
(1) A socket's user ID tree.
(2) A socket's incoming call secureq and acceptq.
(3) A kernel service that has a call in progress.
(4) A queued call work processor. We have to take care to put any call
that we failed to queue.
(5) sk_buffs on a socket's receive queue. A future patch will get rid of
this.
Whilst we're at it, we can do:
(1) Get rid of the RXRPC_CALL_EV_RELEASE event. Release is now done
entirely from the socket routines and never from the call's processor.
(2) Get rid of the RXRPC_CALL_DEAD state. Calls now end in the
RXRPC_CALL_COMPLETE state.
(3) Get rid of the rxrpc_call::destroyer work item. Calls are now torn
down when their refcount reaches 0 and then handed over to RCU for
final cleanup.
(4) Get rid of the rxrpc_call::deadspan timer. Calls are cleaned up
immediately they're finished with and don't hang around.
Post-completion retransmission is handled by the connection processor
once the call is disconnected.
(5) Get rid of the dead call expiry setting as there's no longer a timer
to set.
(6) rxrpc_destroy_all_calls() can just check that the call list is empty.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 7 Sep 2016 14:26:39 +0000 (15:26 +0100)]
rxrpc: Use rxrpc_is_service_call() rather than rxrpc_conn_is_service()
Use rxrpc_is_service_call() rather than rxrpc_conn_is_service() if the call
is available just in case call->conn is NULL.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 7 Sep 2016 14:28:54 +0000 (15:28 +0100)]
rxrpc: Pass the connection pointer to rxrpc_post_packet_to_call()
Pass the connection pointer to rxrpc_post_packet_to_call() as the call
might get disconnected whilst we're looking at it, but the connection
pointer determined by rxrpc_data_read() is guaranteed by RCU for the
duration of the call.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 7 Sep 2016 14:19:25 +0000 (15:19 +0100)]
rxrpc: Cache the security index in the rxrpc_call struct
Cache the security index in the rxrpc_call struct so that we can get at it
even when the call has been disconnected and the connection pointer
cleared.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 7 Sep 2016 13:45:26 +0000 (14:45 +0100)]
rxrpc: Use call->peer rather than call->conn->params.peer
Use call->peer rather than call->conn->params.peer to avoid the possibility
of call->conn being NULL and, whilst we're at it, check it for NULL before we
access it.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 7 Sep 2016 13:34:21 +0000 (14:34 +0100)]
rxrpc: Improve the call tracking tracepoint
Improve the call tracking tracepoint by showing more differentiation
between some of the put and get events, including:
(1) Getting and putting refs for the socket call user ID tree.
(2) Getting and putting refs for queueing and failing to queue the call
processor work item.
Note that these aren't necessarily used in this patch, but will be taken
advantage of in future patches.
An enum is added for the event subtype numbers rather than coding them
directly as decimal numbers and a table of 3-letter strings is provided
rather than a sequence of ?: operators.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 7 Sep 2016 13:42:15 +0000 (14:42 +0100)]
rxrpc: Delete unused rxrpc_kernel_free_skb()
Delete rxrpc_kernel_free_skb() as it's unused.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Wed, 7 Sep 2016 13:43:39 +0000 (14:43 +0100)]
rxrpc: Whitespace cleanup
Remove some whitespace.
Signed-off-by: David Howells <dhowells@redhat.com>
Arnd Bergmann [Tue, 6 Sep 2016 19:20:36 +0000 (21:20 +0200)]
ptp: ixp46x: remove NO_IRQ handling
gpio_to_irq does not return NO_IRQ but instead returns a negative
error code on failure. Returning NO_IRQ from the function has no
negative effects as we only compare the result to the expected
interrupt number, but it's better to return a proper failure
code for consistency, and we should remove NO_IRQ from the kernel
entirely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Tue, 6 Sep 2016 16:50:00 +0000 (17:50 +0100)]
sfc: check MTU against minimum threshold
Reported-by: Ma Yuying <yuma@redhat.com>
Suggested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 6 Sep 2016 13:10:22 +0000 (15:10 +0200)]
perf, bpf: fix conditional call to bpf_overflow_handler
The newly added bpf_overflow_handler function is only built of both
CONFIG_EVENT_TRACING and CONFIG_BPF_SYSCALL are enabled, but the caller
only checks the latter:
kernel/events/core.c: In function 'perf_event_alloc':
kernel/events/core.c:9106:27: error: 'bpf_overflow_handler' undeclared (first use in this function)
This changes the caller so we also skip this call if CONFIG_EVENT_TRACING
is disabled entirely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
aa6a5f3cb2b2 ("perf, bpf: add perf events core support for BPF_PROG_TYPE_PERF_EVENT programs")
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baoyou Xie [Tue, 6 Sep 2016 08:21:56 +0000 (16:21 +0800)]
net: arc_emac: mark arc_mdio_reset() static
We get 1 warning when building kernel with W=1:
drivers/net/ethernet/arc/emac_mdio.c:107:5: warning: no previous prototype for 'arc_mdio_reset' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baoyou Xie [Tue, 6 Sep 2016 08:19:02 +0000 (16:19 +0800)]
lan78xx: mark symbols static where possible
We get a few warnings when building kernel with W=1:
drivers/net/usb/lan78xx.c:1182:6: warning: no previous prototype for 'lan78xx_defer_kevent' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:1409:5: warning: no previous prototype for 'lan78xx_nway_reset' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:2000:5: warning: no previous prototype for 'lan78xx_set_mac_addr' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Sep 2016 21:24:02 +0000 (14:24 -0700)]
Merge branch 'qed-get_regs'
Tomer Tayar [Mon, 5 Sep 2016 11:35:10 +0000 (14:35 +0300)]
qed: Add infrastructure for debug data collection
Adds support for several infrastructure operations that are done as part of
debug data collection.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 5 Sep 2016 10:26:33 +0000 (13:26 +0300)]
bnx2x: Add support for segmentation of tunnels with outer checksums
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 4 Sep 2016 21:24:03 +0000 (14:24 -0700)]
qed: Remove OOM messages
These messages are unnecessary as OOM allocation failures already do
a dump_stack() giving more or less the same information.
$ size drivers/net/ethernet/qlogic/qed/built-in.o* (defconfig x86-64)
text data bss dec hex filename
127817 27969 32800 188586 2e0aa drivers/net/ethernet/qlogic/qed/built-in.o.new
132474 27969 32800 193243 2f2db drivers/net/ethernet/qlogic/qed/built-in.o.old
Miscellanea:
o Change allocs to the generally preferred forms where possible.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Sep 2016 20:53:29 +0000 (13:53 -0700)]
Merge tag 'rxrpc-rewrite-
20160904-2' of git://git./linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Split output code from sendmsg code
Here's a set of small patches that split the packet transmission code from
the sendmsg code and simply rearrange the new file to make it more
logically laid out ready for being rewritten. An enum is also moved out of
the header file to there as it's only used there. This needs to be applied
on top of the just-posted fixes patch set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Sep 2016 20:46:26 +0000 (13:46 -0700)]
Merge tag 'rxrpc-rewrite-
20160904-1' of git://git./linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Small fixes
Here's a set of small fix patches:
(1) Fix some uninitialised variables.
(2) Set the client call state before making it live by attaching it to the
conn struct.
(3) Randomise the epoch and starting client conn ID values, and don't
change the epoch when the client conn ID rolls round.
(4) Replace deprecated create_singlethread_workqueue() calls.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Haishuang Yan [Sun, 4 Sep 2016 10:52:51 +0000 (18:52 +0800)]
vxlan: Update tx_errors statistics if vxlan_build_skb return err.
If vxlan_build_skb return err < 0, tx_errors should be also increased.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brenden Blanco [Sun, 4 Sep 2016 04:29:58 +0000 (21:29 -0700)]
net/mlx4_en: protect ring->xdp_prog with rcu_read_lock
Depending on the preempt mode, the bpf_prog stored in xdp_prog may be
freed despite the use of call_rcu inside bpf_prog_put. The situation is
possible when running in PREEMPT_RCU=y mode, for instance, since the rcu
callback for destroying the bpf prog can run even during the bh handling
in the mlx4 rx path.
Several options were considered before this patch was settled on:
Add a napi_synchronize loop in mlx4_xdp_set, which would occur after all
of the rings are updated with the new program.
This approach has the disadvantage that as the number of rings
increases, the speed of update will slow down significantly due to
napi_synchronize's msleep(1).
Add a new rcu_head in bpf_prog_aux, to be used by a new bpf_prog_put_bh.
The action of the bpf_prog_put_bh would be to then call bpf_prog_put
later. Those drivers that consume a bpf prog in a bh context (like mlx4)
would then use the bpf_prog_put_bh instead when the ring is up. This has
the problem of complexity, in maintaining proper refcnts and rcu lists,
and would likely be harder to review. In addition, this approach to
freeing must be exclusive with other frees of the bpf prog, for instance
a _bh prog must not be referenced from a prog array that is consumed by
a non-_bh prog.
The placement of rcu_read_lock in this patch is functionally the same as
putting an rcu_read_lock in napi_poll. Actually doing so could be a
potentially controversial change, but would bring the implementation in
line with sk_busy_loop (though of course the nature of those two paths
is substantially different), and would also avoid future copy/paste
problems with future supporters of XDP. Still, this patch does not take
that opinionated option.
Testing was done with kernels in either PREEMPT_RCU=y or
CONFIG_PREEMPT_VOLUNTARY=y+PREEMPT_RCU=n modes, with neither exhibiting
any drawback. With PREEMPT_RCU=n, the extra call to rcu_read_lock did
not show up in the perf report whatsoever, and with PREEMPT_RCU=y the
overhead of rcu_read_lock (according to perf) was the same before/after.
In the rx path, rcu_read_lock is eventually called for every packet
from netif_receive_skb_internal, so the napi poll call's rcu_read_lock
is easily amortized.
v2:
Remove extra rcu_read_lock in mlx4_en_process_rx_cq body
Annotate xdp_prog with __rcu, and convert all usages to rcu_assign or
rcu_dereference[_protected] as appropriate.
Add explicit mutex lock around rcu_assign instead of xchg loop.
Fixes:
d576acf0a22 ("net/mlx4_en: add page recycle to prepare rx ring for tx support")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Sep 2016 20:33:20 +0000 (13:33 -0700)]
Merge branch 'mediatek-rx-path-enhancements'
Sean Wang says:
====================
net: ethernet: mediatek: add enhancements to RX path
Changes since v1:
- fix message typos and add coverletter
Changes since v2:
- split from the previous series for submitting add enhancements as
a series targeting 'net-next' and add indents before comments.
Changes since v3:
- merge the patch using PDMA RX path
- fixed the input of mtk_poll_rx is with the remaining budget
Changes since v4:
- save one wmb and register update when no packet is being handled
inside mtk_poll_rx call
- fixed incorrect return packet count from mtk_napi_rx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Sat, 3 Sep 2016 09:59:27 +0000 (17:59 +0800)]
net: ethernet: mediatek: enhance RX path by aggregating more SKBs into NAPI
The patch adds support for aggregating more SKBs feed into NAPI in
order to get more benefits from generic receive offload (GRO) by
peeking at the RX ring status and moving more packets right before
returning from NAPI RX polling handler if NAPI budgets are still
available and some packets already present in hardware.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Sat, 3 Sep 2016 09:59:26 +0000 (17:59 +0800)]
net: ethernet: mediatek: enhance RX path by reducing the frequency of the memory barrier used
The patch makes move wmb() to outside the loop that could help
RX path handling more faster although that RX descriptors aren't
freed for DMA to use as soon as possible, but based on my experiment
and the result shows it still can reach about 943Mbpis without
performance drop that is tested based on the setup with one port
using Giga PHY and 256 RX descriptors for DMA to move.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Sep 2016 20:29:59 +0000 (13:29 -0700)]
Merge branch 'hso-neatening'
Joe Perches says:
====================
hso: neatening
This seems to be the only code in the kernel that uses
macro defines with a trailing underscore. Fix that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Fri, 2 Sep 2016 22:58:02 +0000 (15:58 -0700)]
hso: Convert printk to pr_<level>
Use a more common logging style
Miscellanea:
o Add pr_fmt to prefix each output message
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Fri, 2 Sep 2016 22:58:01 +0000 (15:58 -0700)]
hso: Use a more common logging style
Macros that end in an underscore are just odd.
Add hso_dbg(level, fmt, ...) and use it everwhere instead.
Several uses had additional unnecessary newlines as the
macro added a newline. Remove the newline from the macro
and add newlines to each use as appropriate.
Remove now unused D<digit> macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Woojung Huh [Fri, 2 Sep 2016 20:34:22 +0000 (20:34 +0000)]
smsc95xx: Add mdix control via ethtool
Add mdix control through ethtool.
Signed-off-by: Woojung Huh <Woojung.huh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Woojung Huh [Fri, 2 Sep 2016 20:34:20 +0000 (20:34 +0000)]
smsc95xx: Add register define
Add STRAP_STATUS defines.
Signed-off-by: Woojung Huh <Woojung.huh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Woojung Huh [Fri, 2 Sep 2016 20:34:19 +0000 (20:34 +0000)]
smsc95xx: Add maintainer
Add Microchip Linux Driver Support as maintainer
because this driver is maintaining by Microchip.
Signed-off-by: Woojung Huh <Woojung.huh@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Sep 2016 19:58:14 +0000 (12:58 -0700)]
Merge branch 'mv88e6xxx-isolate-Global2'
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: isolate Global2 support
Registers of Marvell chips are organized in internal SMI devices.
One of them at address 0x1C is called Global2. It provides an extended
set of registers, used for interrupt control, EEPROM access, indirect
PHY access (to bypass the PHY Polling Unit) and cross-chip setup.
Most chips have it, but some others don't (older ones such as 6060).
Now that its related code is isolated in mv88e6xxx_g2_* functions, move
it to its own global2.c file, making most of its setup code static.
Then make its compilation optional, which allows to reduce the size of
the mv88e6xxx driver for devices such as home routers embedding Ethernet
chips without Global2 support.
It is present on most recent chips, thus enable its support by default.
Changes in v2: fail probe if GLOBAL2 is required but not enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 2 Sep 2016 18:45:34 +0000 (14:45 -0400)]
net: dsa: mv88e6xxx: make global2 code optional
Since not every chip has a Global2 set of registers, make its support
optional, in which case the related functions will return -EOPNOTSUPP.
This also allows to reduce the size of the mv88e6xxx driver for devices
such as home routers embedding Ethernet chips without Global2 support.
It is present on most recent chips, thus enable its support by default.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 2 Sep 2016 18:45:33 +0000 (14:45 -0400)]
net: dsa: mv88e6xxx: move Global2 code
Marvell chips are composed of multiple SMI devices. One of them at
address 0x1C is called Global2. It provides an extended set of
registers, used for interrupt control, EEPROM access, indirect PHY
access (to bypass the PHY Polling Unit) and cross-chip related setup.
Most chips have it, but some others don't (older ones such as 6060).
Now that its related code is isolated in mv88e6xxx_g2_* functions, move
it to its own global2.c file, making most of its setup code static.
Document each registers in the meantime.
Its compilation can be later avoided for chips without such registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 2 Sep 2016 18:45:32 +0000 (14:45 -0400)]
net: dsa: mv88e6xxx: fix module naming
Since the mv88e6xxx.c file has been renamed, the driver compiled as a
module is called chip.ko instead of mv88e6xxx.ko. Fix this.
Fixes:
fad09c73c270 ("net: dsa: mv88e6xxx: rename single-chip support")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Sep 2016 19:45:26 +0000 (12:45 -0700)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Most relevant updates are the removal of per-conntrack timers to
use a workqueue/garbage collection approach instead from Florian
Westphal, the hash and numgen expression for nf_tables from Laura
Garcia, updates on nf_tables hash set to honor the NLM_F_EXCL flag,
removal of ip_conntrack sysctl and many other incremental updates on our
Netfilter codebase.
More specifically, they are:
1) Retrieve only 4 bytes to fetch ports in case of non-linear skb
transport area in dccp, sctp, tcp, udp and udplite protocol
conntrackers, from Gao Feng.
2) Missing whitespace on error message in physdev match, from Hangbin Liu.
3) Skip redundant IPv4 checksum calculation in nf_dup_ipv4, from Liping Zhang.
4) Add nf_ct_expires() helper function and use it, from Florian Westphal.
5) Replace opencoded nf_ct_kill() call in IPVS conntrack support, also
from Florian.
6) Rename nf_tables set implementation to nft_set_{name}.c
7) Introduce the hash expression to allow arbitrary hashing of selector
concatenations, from Laura Garcia Liebana.
8) Remove ip_conntrack sysctl backward compatibility code, this code has
been around for long time already, and we have two interfaces to do
this already: nf_conntrack sysctl and ctnetlink.
9) Use nf_conntrack_get_ht() helper function whenever possible, instead
of opencoding fetch of hashtable pointer and size, patch from Liping Zhang.
10) Add quota expression for nf_tables.
11) Add number generator expression for nf_tables, this supports
incremental and random generators that can be combined with maps,
very useful for load balancing purpose, again from Laura Garcia Liebana.
12) Fix a typo in a debug message in FTP conntrack helper, from Colin Ian King.
13) Introduce a nft_chain_parse_hook() helper function to parse chain hook
configuration, this is used by a follow up patch to perform better chain
update validation.
14) Add rhashtable_lookup_get_insert_key() to rhashtable and use it from the
nft_set_hash implementation to honor the NLM_F_EXCL flag.
15) Missing nulls check in nf_conntrack from nf_conntrack_tuple_taken(),
patch from Florian Westphal.
16) Don't use the DYING bit to know if the conntrack event has been already
delivered, instead a state variable to track event re-delivery
states, also from Florian.
17) Remove the per-conntrack timer, use the workqueue approach that was
discussed during the NFWS, from Florian Westphal.
18) Use the netlink conntrack table dump path to kill stale entries,
again from Florian.
19) Add a garbage collector to get rid of stale conntracks, from
Florian.
20) Reschedule garbage collector if eviction rate is high.
21) Get rid of the __nf_ct_kill_acct() helper.
22) Use ARPHRD_ETHER instead of hardcoded 1 from ARP logger.
23) Make nf_log_set() interface assertive on unsupported families.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sun, 4 Sep 2016 12:25:21 +0000 (13:25 +0100)]
rxrpc Move enum rxrpc_command to sendmsg.c
Move enum rxrpc_command to sendmsg.c as it's now only used in that file.
Signed-off-by: David Howells <dhowells@redhat.com>
Bhaktipriya Shridhar [Sun, 4 Sep 2016 15:24:58 +0000 (20:54 +0530)]
fs/afs/flock: Remove deprecated create_singlethread_workqueue
The workqueue "afs_lock_manager" queues work item &vnode->lock_work,
per vnode. Since there can be multiple vnodes and since their work items
can be executed concurrently, alloc_workqueue has been used to replace
the deprecated create_singlethread_workqueue instance.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure because the workqueue is being used on a memory reclaim
path.
Since there are fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 2 Sep 2016 21:39:45 +0000 (22:39 +0100)]
rxrpc: Rearrange net/rxrpc/sendmsg.c
Rearrange net/rxrpc/sendmsg.c to be in a more logical order. This makes it
easier to follow and eliminates forward declarations.
Signed-off-by: David Howells <dhowells@redhat.com>
Bhaktipriya Shridhar [Sun, 4 Sep 2016 15:24:11 +0000 (20:54 +0530)]
fs/afs/callback: Remove deprecated create_singlethread_workqueue
The workqueue "afs_callback_update_worker" queues multiple work items
viz &vnode->cb_broken_work, &server->cb_break_work which require strict
execution ordering. Hence, an ordered dedicated workqueue has been used.
Since the workqueue is being used on a memory reclaim path, WQ_MEM_RECLAIM
has been set to ensure forward progress under memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 2 Sep 2016 21:39:45 +0000 (22:39 +0100)]
rxrpc: Split sendmsg from packet transmission code
Split the sendmsg code from the packet transmission code (mostly to be
found in output.c).
Signed-off-by: David Howells <dhowells@redhat.com>
Bhaktipriya Shridhar [Sun, 4 Sep 2016 15:23:42 +0000 (20:53 +0530)]
fs/afs/rxrpc: Remove deprecated create_singlethread_workqueue
The workqueue "afs_async_calls" queues work item
&call->async_work per afs_call. Since there could be multiple calls and since
these calls can be run concurrently, alloc_workqueue has been used to replace
the deprecated create_singlethread_workqueue instance.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure because the workqueue is being used on a memory reclaim
path.
Since there are fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Bhaktipriya Shridhar [Sun, 4 Sep 2016 15:22:39 +0000 (20:52 +0530)]
fs/afs/vlocation: Remove deprecated create_singlethread_workqueue
The workqueue "afs_vlocation_update_worker" queues a single work item
&afs_vlocation_update and hence it doesn't require execution ordering.
Hence, alloc_workqueue has been used to replace the deprecated
create_singlethread_workqueue instance.
Since the workqueue is being used on a memory reclaim path, WQ_MEM_RECLAIM
flag has been set to ensure forward progress under memory pressure.
Since there are fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Sun, 4 Sep 2016 12:14:46 +0000 (13:14 +0100)]
rxrpc: Don't change the epoch
It seems the local epoch should only be changed on boot, so remove the code
that changes it for client connections.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 2 Sep 2016 21:39:45 +0000 (22:39 +0100)]
rxrpc: Randomise epoch and starting client conn ID values
Create a random epoch value rather than a time-based one on startup and set
the top bit to indicate that this is the case.
Also create a random starting client connection ID value. This will be
incremented from here as new client connections are created.
Signed-off-by: David Howells <dhowells@redhat.com>
Paul Burton [Fri, 2 Sep 2016 14:22:48 +0000 (15:22 +0100)]
net: ti: cpmac: Fix compiler warning due to type confusion
cpmac_start_xmit() used the max() macro on skb->len (an unsigned int)
and ETH_ZLEN (a signed int literal). This led to the following compiler
warning:
In file included from include/linux/list.h:8:0,
from include/linux/module.h:9,
from drivers/net/ethernet/ti/cpmac.c:19:
drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_start_xmit':
include/linux/kernel.h:748:17: warning: comparison of distinct pointer
types lacks a cast
(void) (&_max1 == &_max2); \
^
drivers/net/ethernet/ti/cpmac.c:560:8: note: in expansion of macro 'max'
len = max(skb->len, ETH_ZLEN);
^
On top of this, it assigned the result of the max() macro to a signed
integer whilst all further uses of it result in it being cast to varying
widths of unsigned integer.
Fix this up by using max_t to ensure the comparison is performed as
unsigned integers, and for consistency change the type of the len
variable to unsigned int.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 2 Sep 2016 13:43:53 +0000 (19:13 +0530)]
cxgb4: Add support for ndo_get_vf_config
Adds support for ndo_get_vf_config, also fill the default mac address
that will be provided to the VF by firmware, in case user doesn't
provide one. So user can get the default MAC address address also
through ndo_get_vf_config.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 4 Sep 2016 18:39:59 +0000 (11:39 -0700)]
Merge branch 'netns-opt'
Cong Wang says:
====================
net: some minor optimization for netns id
Cong Wang (2):
vxlan: call peernet2id() in fdb notification
netns: avoid disabling irq for netns id
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Fri, 2 Sep 2016 04:53:45 +0000 (21:53 -0700)]
netns: avoid disabling irq for netns id
We never read or change netns id in hardirq context,
the only place we read netns id in softirq context
is in vxlan_xmit(). So, it should be enough to just
disable BH.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Fri, 2 Sep 2016 04:53:44 +0000 (21:53 -0700)]
vxlan: call peernet2id() in fdb notification
netns id should be already allocated each time we change
netns, that is, in dev_change_net_namespace() (more precisely
in rtnl_fill_ifinfo()). It is safe to just call peernet2id() here.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Fri, 2 Sep 2016 01:01:47 +0000 (18:01 -0700)]
openvswitch: Free tmpl with tmpl_free.
When an error occurs during conntrack template creation as part of
actions validation, we need to free the template. Previously we've been
using nf_ct_put() to do this, but nf_ct_tmpl_free() is more appropriate.
Signed-off-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sun, 4 Sep 2016 12:10:10 +0000 (13:10 +0100)]
rxrpc: The client call state must be changed before attachment to conn
We must set the client call state to RXRPC_CALL_CLIENT_SEND_REQUEST before
attaching the call to the connection struct, not after, as it's liable to
receive errors and conn aborts as soon as the assignment is made - and
these will cause its state to be changed outside of the initiating thread's
control.
Signed-off-by: David Howells <dhowells@redhat.com>
David S. Miller [Sat, 3 Sep 2016 00:11:32 +0000 (17:11 -0700)]
Merge branch 'liquidio-CN23XX-part-2'
Raghu Vatsavayi says:
====================
liquidio CN23XX support
I am posting the remaining half of patchset after the
acceptance of first half. With this patchset I am able
to completely submit the code of V3 patchset which you
earlier advised me to split into smaller ones.
This V5 patch also addresses all the comments from previous
submission:
1) Avoid busy loop while reading registers.
2) Other minor comments about debug messages and constants.
Please apply patches in following order as some of the
patches depend on earlier patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 1 Sep 2016 18:16:11 +0000 (11:16 -0700)]
liquidio:CN23XX pause frame support
Adds support for pause frame and priv flag for cn23xx
device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 1 Sep 2016 18:16:10 +0000 (11:16 -0700)]
liquidio: CN23XX napi support
This patch adds NAPI related support for cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 1 Sep 2016 18:16:09 +0000 (11:16 -0700)]
liquidio: CN23XX health monitoring
Adds support for watchdog based health monitoring
of octeon cores on cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 1 Sep 2016 18:16:08 +0000 (11:16 -0700)]
liquidio: ethtool and led control support
This patch adds support for some control operations like
LED identification, ethtool statistics and intr config for
cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 1 Sep 2016 18:16:07 +0000 (11:16 -0700)]
liquidio: CN23XX octeon3 instruction
Adds support for data path related changes based
on octeon3 instruction header(ih3) for cn23xx.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 1 Sep 2016 18:16:06 +0000 (11:16 -0700)]
liquidio: CN23XX IQ access
Adds support for Instruction Queue(IQ) index manipulation
routines through bar1 of cn23xx.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 1 Sep 2016 18:16:05 +0000 (11:16 -0700)]
liquidio: RX control commands
Adds support for RX control commands on cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 1 Sep 2016 18:16:04 +0000 (11:16 -0700)]
liquidio: link and control commands
This patch adds work queue support for link status and
control commands.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 3 Sep 2016 00:10:25 +0000 (17:10 -0700)]
Merge branch 'tipc-scalable-broadcast-NACK'
Jon Maloy says:
====================
tipc: improve broadcast NACK mechanism
The broadcast protocol has turned out to not scale well beyond 70-80
nodes, while it is now possible to build TIPC clusters of at least ten
times that size. This commit series improves the NACK/retransmission
mechanism of the broadcast protocol to make is at scalable as the rest
of TIPC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 1 Sep 2016 17:52:51 +0000 (13:52 -0400)]
tipc: send broadcast nack directly upon sequence gap detection
Because of the risk of an excessive number of NACK messages and
retransissions, receivers have until now abstained from sending
broadcast NACKS directly upon detection of a packet sequence number
gap. We have instead relied on such gaps being detected by link
protocol STATE message exchange, something that by necessity delays
such detection and subsequent retransmissions.
With the introduction of unicast NACK transmission and rate control
of retransmissions we can now remove this limitation. We now allow
receiving nodes to send NACKS immediately, while coordinating the
permission to do so among the nodes in order to avoid NACK storms.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 1 Sep 2016 17:52:50 +0000 (13:52 -0400)]
tipc: rate limit broadcast retransmissions
As cluster sizes grow, so does the amount of identical or overlapping
broadcast NACKs generated by the packet receivers. This often leads to
'NACK crunches' resulting in huge numbers of redundant retransmissions
of the same packet ranges.
In this commit, we introduce rate control of broadcast retransmissions,
so that a retransmitted range cannot be retransmitted again until after
at least 10 ms. This reduces the frequency of duplicate, redundant
retransmissions by an order of magnitude, while having a significant
positive impact on overall throughput and scalability.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 1 Sep 2016 17:52:49 +0000 (13:52 -0400)]
tipc: transfer broadcast nacks in link state messages
When we send broadcasts in clusters of more 70-80 nodes, we sometimes
see the broadcast link resetting because of an excessive number of
retransmissions. This is caused by a combination of two factors:
1) A 'NACK crunch", where loss of broadcast packets is discovered
and NACK'ed by several nodes simultaneously, leading to multiple
redundant broadcast retransmissions.
2) The fact that the NACKS as such also are sent as broadcast, leading
to excessive load and packet loss on the transmitting switch/bridge.
This commit deals with the latter problem, by moving sending of
broadcast nacks from the dedicated BCAST_PROTOCOL/NACK message type
to regular unicast LINK_PROTOCOL/STATE messages. We allocate 10 unused
bits in word 8 of the said message for this purpose, and introduce a
new capability bit, TIPC_BCAST_STATE_NACK in order to keep the change
backwards compatible.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Wu [Thu, 1 Sep 2016 17:50:01 +0000 (01:50 +0800)]
net: stmmac: dwmac-rk: add pd_gmac support for rk3399
Add the gmac power domain support for rk3399, in order to save more
power consumption.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Chen [Thu, 1 Sep 2016 17:50:00 +0000 (01:50 +0800)]
net: stmmac: dwmac-rk: fixes the gmac resume after PD on/off
GMAC Power Domain(PD) will be disabled during suspend.
That will causes GRF registers reset.
So corresponding GRF registers for GMAC must be setup again.
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Chen [Thu, 1 Sep 2016 17:49:59 +0000 (01:49 +0800)]
net: stmmac: dwmac-rk: add rk3366 & rk3399 specific data
Add constants and callback functions for the dwmac on rk3228/rk3229 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>