OSDN Git Service
Felipe Balbi [Tue, 27 Jan 2015 19:48:14 +0000 (13:48 -0600)]
usb: dwc3: remove reliance on dev_vdbg()
By moving all dev_vdbg() to tracepoints, we
can finally get rid of dev_vdbg() usage from
dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi [Tue, 27 Jan 2015 19:47:02 +0000 (13:47 -0600)]
usb: dwc3: trace: add trace logs for core and gadget
Sometimes we want to just print a formatted
string without passing any extra data. The
following will be used for removing reliance
on dev_vdbg() from dwc3.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi [Tue, 27 Jan 2015 19:49:28 +0000 (13:49 -0600)]
usb: dwc3: gadget: WARN() in case of unknown IRQ
if an unknown IRQ event is triggered, that means
the HW is really misbehaving. Instead of printing
a debug message, let's WARN() so users report
when that happens.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi [Tue, 27 Jan 2015 19:24:26 +0000 (13:24 -0600)]
usb: dwc3: gadget: avoid variable shadowing
We already have both ret and dwc defined in this
same function.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Andrzej Pietrasiewicz [Mon, 19 Jan 2015 12:52:58 +0000 (13:52 +0100)]
usb: gadget: uvc: comments for iterating over streaming hierarchy
The purpose of the functions and their parametrs might not be obvious
to the reader, so explain it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Andrzej Pietrasiewicz [Mon, 19 Jan 2015 12:52:57 +0000 (13:52 +0100)]
usb: gadget: uvc: use explicit type instead of void *
The first parameter of __uvcg_iter_strm_cls() is always used in
the context of struct uvcg_streaming_header, so change the
function prototype accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Peter Chen [Fri, 16 Jan 2015 10:29:01 +0000 (18:29 +0800)]
usb: phy: mxs: add delay before set phyctrl.clkgate
There is a request from IC engineer that if we doesn't
set phypwd as 0xffffffff, we need to delay about five
32Khz cycles before set phy's pwd register, otherwise,
the wakeup signal may can't wake up controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Peter Chen [Fri, 16 Jan 2015 10:29:00 +0000 (18:29 +0800)]
usb: phy: mxs: do not set PWD.RXPWD1PT1 for low speed connection
At very rare cases, the SoF will not send out after resume with
low speed connection. The workaround is do not power down
PWD.RXPWD1PT1 bit during the suspend.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Li Jun [Fri, 16 Jan 2015 10:28:59 +0000 (18:28 +0800)]
usb: phy: mxs: refine mxs_phy_disconnect_line
For non-otg mode, we keep the usage of disconnect line between phy analog
and digital unchanging; for otg mode, at peripheral role, we keep the usage
unchanging too, at host role, the digital part needs to know dp/dm change
to respond device's data pulse when it is at low power mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Peter Chen [Fri, 16 Jan 2015 10:28:58 +0000 (18:28 +0800)]
usb: phy: mxs: don't need IP fix for imx6sx
The RLT code has already done it, so no software operation is needed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:56:05 +0000 (00:56 +0200)]
usb: isp1760: Fix USB disabled check
The isp1760 driver registration function returns an error if USB is
disabled. This made sense when the driver only supported host
controllers, but now that it supports peripheral controllers host
support isn't mandatory anymore.
Fix this by returning an error only when both the HCD and UDC functions
are disabled, either through the kernel configuration or at runtime.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:56:04 +0000 (00:56 +0200)]
usb: isp1760: Remove duplicate usb_disabled() check
Both isp1760_register() and isp1761_pci_probe() check whether USB is
disabled by calling usb_disabled(), and bail out with an error if it is.
One check is enough, remove the PCI-specific check.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:56:03 +0000 (00:56 +0200)]
usb: isp1760: Make HCD support optional
Enable compilation of the isp1760 driver in pure host mode, pure device
mode, or dual-role mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:56:02 +0000 (00:56 +0200)]
usb: isp1760: Move driver from drivers/usb/host/ to drivers/usb/isp1760/
Now that this is DRD, it doesn't make sense to keep it under
drivers/usb/host.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:56:01 +0000 (00:56 +0200)]
usb: isp1760: Add device controller support
The ISP1761 is a dual-mode host and device controller backward
compatible on the host side with the ISP1760. Add support for the device
controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:56:00 +0000 (00:56 +0200)]
usb: isp1760: Move PORT1 configuration to core code
Configuring the mode of operation of port 1 doesn't belong to the HCD
code, as it's related to the soon to come UDC support. Move the
configuration to core code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:59 +0000 (00:55 +0200)]
usb: isp1760: Initialize the bus interface in core code
Although the corresponding register is part of the HCD register space,
processor bus initialization is not specific to the HCD. To prepare for
device controller support, move bus interface initialization to core
code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:58 +0000 (00:55 +0200)]
usb: isp1760: Set IRQF_SHARED flag in core code
The IRQF_SHARED flag needs to be set regardless of the bus type. Don't
require glue code to set it manually.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:57 +0000 (00:55 +0200)]
usb: isp1760: Move core code to isp1760-core.c
Move core device initialization to a central location in order to share
it with the device mode implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:56 +0000 (00:55 +0200)]
usb: isp1760: Reorganize header files
The isp1760-rhcd.h header contains PTD constants and structures only
useful for the HCD implementation. It also contains register definitions
that will be needed by common code when implementing support for the
ISP1761 device controller, but doesn't contain the isp1760_hcd structure
definition that will also be used by common code.
Move definitions to the right location and create an isp1760-regs.h to
store register definitions. No change other than moving definitions and
modifying indentation is performed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:55 +0000 (00:55 +0200)]
usb: isp1760: Prefix driver data structures with isp1760_
The slotinfo and memory_chunk structures are specific to the driver and
defined in a header file. Prefix them with isp1760_ to avoid namespace
clashes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:54 +0000 (00:55 +0200)]
usb: isp1760: Decouple usb_hdc and isp1760_priv
Allocate the driver private data structure manually instead of using the
usb_hcd private space. This will allow skipping hcd registration for the
isp1761 when used in device mode only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:53 +0000 (00:55 +0200)]
usb: isp1760: Refactor PCI initialization code
Move the initialization code out of the PCI probe function to a new
function in order to simplify and fix error handling.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:52 +0000 (00:55 +0200)]
usb: isp1760: Use the managed devm_ioremap_resource() API
This simplifies error and remove code paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:51 +0000 (00:55 +0200)]
usb: isp1760: Pass resource pointer to isp1760_register
The function takes quite a few arguments, passing the resource pointer
instead of the start address and length simplifies it a bit.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:50 +0000 (00:55 +0200)]
usb: isp1760: Remove busname argument to isp1760_register
The argument is unused, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:49 +0000 (00:55 +0200)]
usb: isp1760: Prefix init_kmem_once and deinit_kmem_cache with isp1760_
The two functions are specific to the driver but have very generic
names, subject to collisions. Rename them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:48 +0000 (00:55 +0200)]
usb: isp1760: Fix indentation in probe error path
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:47 +0000 (00:55 +0200)]
usb: isp1760: Don't expose hcd to glue code from isp1760_register
The glue code probe functions don't need to access the hcd structure
anymore. Modify isp1760_register to return an integer error code instead
of the hcd pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:46 +0000 (00:55 +0200)]
usb: isp1760: Manage device driver data in common code
Don't duplicate *_set_drvdata calls in glue code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:45 +0000 (00:55 +0200)]
usb: isp1760: Move removal cleanup code to isp1760-hcd.c
The removal cleanup code is duplicated between the different bus glues.
Move it to a central location.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:44 +0000 (00:55 +0200)]
usb: isp1760: Merge platform and OF glue codes
Both handle platform devices, merge them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:43 +0000 (00:55 +0200)]
usb: isp1760: Unmap I/O registers at platform device removal
The I/O registers are mapped in the HCD code but must be unmapped by
glue code. The OF and PCI glue code unmap them correctly but the
platform glue code is missing an iounmap() call. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:42 +0000 (00:55 +0200)]
usb: isp1760: Retrieve pdev memory resource from hcd at remove time
The platform driver remove function needs to release the memory resource
requested at probe time. Instead of retrieving the resource from the
platform device, retrieve it from the usb_hcd. This mimics the behaviour
of the PCI and OF glues, and will make it easier to share code between
all three glue layers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:41 +0000 (00:55 +0200)]
usb: isp1760: Remove isp1760 glue structure
The structure is allocated for the sole purpose of holding a pointer to
the HCD and being stored in platform device driver data. Store the HCD
pointer directly instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Laurent Pinchart [Tue, 20 Jan 2015 22:55:40 +0000 (00:55 +0200)]
usb: isp1760: Use the gpio descriptor API
Switching to the managed gpio descriptor API simplifies both error and
cleanup code paths (by removing the need to free the gpio) and runtime
code (by removing manual handling of the active low flag). It also
permits handling the reset gpio entirely from within the HCD code,
sharing it between the different glue layers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Asaf Vertz [Wed, 21 Jan 2015 09:06:34 +0000 (11:06 +0200)]
usb: gadget: zero: fix format string warnings
Fixed the following warnings (reported by cppcheck):
[drivers/usb/gadget/function/f_sourcesink.c:1217]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1261]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1305]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1349]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1393]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1437]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1476]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1520]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1564]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
[drivers/usb/gadget/function/f_sourcesink.c:1608]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'
Reviewed-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Robert Baldyga [Fri, 23 Jan 2015 12:41:01 +0000 (13:41 +0100)]
usb: gadget: ffs: add eventfd notification about ffs events
Add eventfd which notifies userspace about ep0 events and AIO completion
events. It simplifies using of FunctionFS with event loop, because now
we need to poll on single file (instead of polling on ep0 and eventfd's
supplied to AIO layer).
FunctionFS eventfd is not triggered if another eventfd is supplied to
AIO layer (in AIO request). It can be useful, for example, when we want
to handle AIO transations for chosen endpoint in separate thread.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mario Schuknecht [Mon, 26 Jan 2015 19:40:21 +0000 (20:40 +0100)]
usb: gadget: f_fs: Fix loop variable
Use if-loop variable 'epfile' instead of start variable 'epfiles'. Now the
correct endpoint file name is stored.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mario Schuknecht [Mon, 26 Jan 2015 19:30:27 +0000 (20:30 +0100)]
usb: gadget: Fix os desc test
USB vendor type is encoded in field bmRequestType. Make test USB_TYPE_VENDOR
with bRequestType instead of bRequest.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Bin Liu [Mon, 26 Jan 2015 22:22:07 +0000 (16:22 -0600)]
usb: musb: cppi41: improve rx channel abort routine
1. set AUTOREQ to NONE at the beginning of teardown;
2. add delay for dma pipeline to drain;
3. Do not set USB_TDOWN bit for RX teardown.
The CPPI hw has an issue that when tearing down a RX channel, if
another RX channel is receiving data, the CPPI will lockup.
To workaround the issue, do not set the CPPI TD bit. The steps before
this point ensures the CPPI channel will be torn down properly.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Bin Liu [Mon, 26 Jan 2015 22:22:06 +0000 (16:22 -0600)]
usb: musb: cppi41: correct the macro name EP_MODE_AUTOREG_*
The macro EP_MODE_AUTOREG_* should be called EP_MODE_AUTOREQ_*, as they
are used for register AUTOREQ.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Yoshihiro Shimoda [Mon, 19 Jan 2015 03:53:17 +0000 (12:53 +0900)]
usb: renesas_usbhs: add support for requesting DT DMA
This patch adds dma_request_slave_channel_reason() calling to request
dma slave channels for multiplatform environment.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Yoshihiro Shimoda [Mon, 19 Jan 2015 03:53:16 +0000 (12:53 +0900)]
usb: renesas_usbhs: add usbhsf_dma_init_pdev() function
To add support for requesting DT DMA in the future, this patch adds
usbhsf_dma_init_pdev() function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sergei Shtylyov [Sun, 18 Jan 2015 22:59:09 +0000 (01:59 +0300)]
usb: renesas_usbhs: mod_host: use HUB_CHAR_*
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sergei Shtylyov [Sun, 18 Jan 2015 22:57:18 +0000 (01:57 +0300)]
usb: musb: virthub: use HUB_CHAR_*
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sergei Shtylyov [Sun, 18 Jan 2015 22:55:55 +0000 (01:55 +0300)]
usb: dummy_hcd: use HUB_CHAR_*
Fix using the bare numbers to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sergei Shtylyov [Sun, 18 Jan 2015 22:54:15 +0000 (01:54 +0300)]
usb: dwc2: hcd: use HUB_CHAR_*
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Andrzej Pietrasiewicz [Fri, 16 Jan 2015 14:14:27 +0000 (15:14 +0100)]
usb: gadget: uvc: preserve the address passed to kfree()
__uvcg_fill_strm() called from __uvcg_iter_stream_cls()
might have advanced the "data" even if __uvcg_iter_stream_cls()
returns an error, so use a backup copy as an argument to kfree().
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Paul Zimmerman [Thu, 15 Jan 2015 20:14:10 +0000 (20:14 +0000)]
MAINTAINERS: update maintainer entry for dwc2 driver
Update the MAINTAINERS entry for the dwc2 driver to show John Youn
as the new maintainer
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Paul Zimmerman [Thu, 15 Jan 2015 19:21:46 +0000 (19:21 +0000)]
Revert "usb: dwc2: add bus suspend/resume for dwc2"
This reverts commit
0cf884e819e05437287a668b9bfcc198bab6329c.
Even after applying the follow-on patch at
https://patchwork.kernel.org/patch/
5325111
there are still problems with device connect on the Altera SOCFPGA
platform at least. One possible fix would be to add a whitelist
to enable suspend/resume on platforms where it does work correctly.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Andy Shevchenko [Thu, 15 Jan 2015 11:40:04 +0000 (13:40 +0200)]
usb: gadget: ethernet: re-use %pM specifier to print MAC
Instead of custom approach the patch converts code to use %pM specifier to
print MAC.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Paul Zimmerman [Thu, 15 Jan 2015 02:45:12 +0000 (02:45 +0000)]
usb: phy: make GPIOs optional for the generic phy
The use of GPIOs should be optional for the generic phy, otherwise
the Altera SOCFPGA platform at least is broken.
Fixes breakage caused by a combination of
e9f2cefb0cd "usb: phy:
generic: migrate to gpio_desc" and
135b3c4304d "usb: dwc2: platform:
add generic PHY framework support".
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Dan Carpenter [Wed, 14 Jan 2015 21:06:35 +0000 (00:06 +0300)]
usb: gadget: uvc: cleanup UVCG_FRAME_ATTR macro
1) Change "conv" an "vnoc" to "to_cpu_endian" to "to_little_endian".
2) No need to check the "limit" because that is already handled in
kstrtoXX so delete that parameter along with the check.
3) By using a "bits" parameter, we can combine the "uxx" parameter and
the "str2u" parameters.
4) The kstrtou##bits() conversion does not need to be done under the
mutex so move it to the start of the function.
5) Change the name of "identity_conv" to "noop_conversion".
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Dan Carpenter [Wed, 14 Jan 2015 21:03:08 +0000 (00:03 +0300)]
usb: gadget: uvc: memory leak in uvcg_frame_make()
We need to add a kfree(h) on an error path.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Dan Carpenter [Wed, 14 Jan 2015 21:02:18 +0000 (00:02 +0300)]
usb: gadget: uvc: remove an impossible condition
"num" is a u32 so "(num > 0xFFFFFFFF)" is never true. Also the range
is already checked in kstrtou32().
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Dan Carpenter [Wed, 14 Jan 2015 20:59:48 +0000 (23:59 +0300)]
usb: gadget: uvc: fix some error codes
We're basically saying ERR_CAST(NULL) and PTR_ERR(NULL) here, which is
nonsensical.
Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi [Mon, 19 Jan 2015 15:57:20 +0000 (09:57 -0600)]
Merge tag 'v3.19-rc5' into next
Linux 3.19-rc5
Conflicts:
drivers/usb/dwc2/gadget.c
drivers/usb/gadget/udc/bdc/bdc_ep.c
Linus Torvalds [Sun, 18 Jan 2015 06:02:20 +0000 (18:02 +1200)]
Linux 3.19-rc5
Linus Torvalds [Sun, 18 Jan 2015 06:00:40 +0000 (18:00 +1200)]
Merge tag 'armsoc-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various
bugs around clocks, reg ranges, etc. There's also a few defconfig
updates (which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but nothing
in here seems particularly risky"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
reset: sunxi: fix spinlock initialization
ARM: dts: disable CCI on exynos5420 based arndale-octa
drivers: bus: check cci device tree node status
ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
ARM: nomadik: fix up leftover device tree pins
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
ARM: exynos_defconfig: Enable LM90 driver
ARM: exynos_defconfig: Enable options for display panel support
arm: dts: Use pmu_system_controller phandle for dp phy
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
...
Linus Torvalds [Sun, 18 Jan 2015 03:29:11 +0000 (15:29 +1200)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock driver fixes from Mike Turquette:
"Small number of fixes for clock drivers and a single null pointer
dereference fix in the framework core code.
The driver fixes vary from fixing section mismatch warnings to
preventing machines from hanging (and preventing developers from
crying)"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: fix possible null pointer dereference
Revert "clk: ppc-corenet: Fix Section mismatch warning"
clk: rockchip: fix deadlock possibility in cpuclk
clk: berlin: bg2q: remove non-exist "smemc" gate clock
clk: at91: keep slow clk enabled to prevent system hang
clk: rockchip: fix rk3288 cpuclk core dividers
clk: rockchip: fix rk3066 pll lock bit location
clk: rockchip: Fix clock gate for rk3188 hclk_emem_peri
clk: rockchip: add CLK_IGNORE_UNUSED flag to fix rk3066/rk3188 USB Host
Linus Torvalds [Sun, 18 Jan 2015 03:26:52 +0000 (15:26 +1200)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is one fix for a Multiqueue sleeping in invalid context problem
and a MAINTAINER file update for Qlogic"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ->queue_rq can't sleep
MAINTAINERS: Update maintainer list for qla4xxx
Stanimir Varbanov [Mon, 5 Jan 2015 16:04:23 +0000 (18:04 +0200)]
clk: fix possible null pointer dereference
The commit
646cafc6 (clk: Change clk_ops->determine_rate to
return a clk_hw as the best parent) opens a possibility for
null pointer dereference, fix this.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Kevin Hao [Wed, 3 Dec 2014 08:53:51 +0000 (16:53 +0800)]
Revert "clk: ppc-corenet: Fix Section mismatch warning"
This reverts commit
da788acb28386aa896224e784954bb73c99ff26c.
That commit tried to fix the section mismatch warning by moving the
ppc_corenet_clk_driver struct to init section. This is definitely wrong
because the kernel would free the memories occupied by this struct
after boot while this driver is still registered in the driver core.
The kernel would panic when accessing this driver struct.
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Heiko Stübner [Fri, 16 Jan 2015 16:52:44 +0000 (17:52 +0100)]
clk: rockchip: fix deadlock possibility in cpuclk
Lockdep reported a possible deadlock between the cpuclk lock and for example
the i2c driver.
CPU0 CPU1
---- ----
lock(clk_lock);
local_irq_disable();
lock(&(&i2c->lock)->rlock);
lock(clk_lock);
<Interrupt>
lock(&(&i2c->lock)->rlock);
*** DEADLOCK ***
The generic clock-types of the core ccf already use spin_lock_irqsave when
touching clock registers, so do the same for the cpuclk.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: removed initialization of "flags"]
Linus Torvalds [Sat, 17 Jan 2015 18:26:24 +0000 (06:26 +1200)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Two patches, the first by Andy to fix dw dmac runtime pm and second
one by me to fix the dmaengine headers in MAINTAINERS"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw: balance PM runtime calls
MAINTAINERS: dmaengine: fix the header file for dmaengine
Linus Torvalds [Sat, 17 Jan 2015 18:24:30 +0000 (06:24 +1200)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also two PMU driver fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools powerpc: Use dwfl_report_elf() instead of offline.
perf tools: Fix segfault for symbol annotation on TUI
perf test: Fix dwarf unwind using libunwind.
perf tools: Avoid build splat for syscall numbers with uclibc
perf tools: Elide strlcpy warning with uclibc
perf tools: Fix statfs.f_type data type mismatch build error with uclibc
tools: Remove bitops/hweight usage of bits in tools/perf
perf machine: Fix __machine__findnew_thread() error path
perf tools: Fix building error in x86_64 when dwarf unwind is on
perf probe: Propagate error code when write(2) failed
perf/x86/intel: Fix bug for "cycles:p" and "cycles:pp" on SLM
perf/rapl: Fix sysfs_show() initialization for RAPL PMU
Ingo Molnar [Sat, 17 Jan 2015 10:04:35 +0000 (11:04 +0100)]
Merge tag 'perf-urgent-for-mingo' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix segfault when using both the map symtab viewer and annotation
in the TUI (Namhyung Kim).
- uClibc build fixes (Alexey Brodkin, Vineet Gupta).
- bitops/hweight were moved from tools/perf/ too tools/include, move
some leftovers (Arnaldo Carvalho de Melo)
- Fix dwarf unwind x86_64 build error (Namhyung Kim)
- Fix __machine__findnew_thread() error path (Namhyung Kim)
- Propagate error code when write(2) failed in 'perf probe' (Namhyung Kim)
- Use dwfl_report_elf() instead of offline in powerpc bits to
properly handle non prelinked DSOs (Sukadev Bhattiprolu).
- Fix dwarf unwind using libunwind in 'perf test' (Wang Nan)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Olof Johansson [Thu, 15 Jan 2015 23:45:18 +0000 (15:45 -0800)]
Merge tag 'samsung-fixes-3.19' of git://git./linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes for v3.19" from Kukjin Kim:
Samsung fixes for v3.19
- exynos_defconfig: enable LM90 driver and display panel support
- HWMON
- SENSORS_LM90
- Direct Rendering Manager (DRM)
- DRM bridge registration and lookup framework
- Parade ps8622/ps8625 eDP/LVDS bridge
- NXP ptn3460 eDP/LVDS bridge
- Exynos Fully Interactive Mobile Display controller (FIMD)
- Panel registration and lookup framework
- Simple panels
- Backlight & LCD device support
- use pmu_system_controller phandle for dp phy
: DP PHY requires pmu_system_controller to handle PMU reg. now
* tag 'samsung-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable LM90 driver
ARM: exynos_defconfig: Enable options for display panel support
arm: dts: Use pmu_system_controller phandle for dp phy
Signed-off-by: Olof Johansson <olof@lixom.net>
Tyler Baker [Mon, 12 Jan 2015 15:54:46 +0000 (07:54 -0800)]
reset: sunxi: fix spinlock initialization
Call spin_lock_init() before the spinlocks are used, both in early init
and probe functions preventing a lockdep splat.
I have been observing lockdep complaining [1] during boot on my a80 optimus [2]
when CONFIG_PROVE_LOCKING has been enabled. This patch resolves the splat,
and has been tested on a few other sunxi platforms without issue.
[1] http://storage.kernelci.org/next/next-
20150107/arm-multi_v7_defconfig+CONFIG_PROVE_LOCKING=y/lab-tbaker/boot-sun9i-a80-optimus.html
[2] http://kernelci.org/boot/?a80-optimus
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 13 Jan 2015 23:32:43 +0000 (15:32 -0800)]
Merge tag 'renesas-soc-fixes-for-v3.19' of git://git./linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Fixes for v3.19" from Simon Horman:
Renesas ARM Based SoC Fixes for v3.19
This pull request is based on the last round of SoC updates for v3.19,
Fourth Round of Renesas ARM Based SoC Updates for v3.19, tagged as
renesas-soc3-for-v3.19, merged into your next/soc branch and included in
v3.19-rc1.
- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds
Set .control_parent for all irqpin instances for sh73a0 SoC when booting
using legacy C.
- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds
This fixes a long standing problem which has been present since
the sh73a0 SoC started using the INTC External IRQ pin driver.
The patch that introduced the problem is
341eb5465f67437a ("ARM:
shmobile: INTC External IRQ pin driver on sh73a0") which was included
in v3.10.
* tag 'renesas-soc-fixes-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds
Abhilash Kesavan [Sat, 10 Jan 2015 03:11:36 +0000 (08:41 +0530)]
ARM: dts: disable CCI on exynos5420 based arndale-octa
The arndale-octa board was giving "imprecise external aborts" during
boot-up with MCPM enabled. CCI enablement of the boot cluster was found
to be the cause of these aborts (possibly because the secure f/w was not
allowing it). Hence, disable CCI for the arndale-octa board.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Abhilash Kesavan [Sat, 10 Jan 2015 03:11:35 +0000 (08:41 +0530)]
drivers: bus: check cci device tree node status
The arm-cci driver completes the probe sequence even if the cci node is
marked as disabled. Add a check in the driver to honour the cci status
in the device tree.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 12 Jan 2015 22:11:58 +0000 (14:11 -0800)]
Merge tag 'at91-fixes' of git://git./linux/kernel/git/nferre/linux-at91 into fixes
Merge "at91: fixes for 3.19 #1 (ter)" from Nicolas Ferre:
First fixes batch for AT91 on 3.19:
- fix some DT entries
- correct clock entry for the at91sam9263 LCD
- add a phy_fixup for Eth1 on sama5d4
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: Olof Johansson <olof@lixom.net>
Heiko Stübner [Sun, 11 Jan 2015 22:09:23 +0000 (23:09 +0100)]
ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
rk3288 SoCs have a function to automatically switch between jtag/sdmmc pinmux
settings depending on the card state. This collides with a lot of assumptions.
It only works when using the internal card-detect mechanism and breaks
horribly when using either the normal card-detect via the slot-gpio function
or via any other pin. Also there is of course no link between the mmc and jtag
on the software-side, so the jtag clocks may very well be disabled when the
card is ejected and the soc switches back to the jtag pinmux.
Leaving the switching function enabled did result in mmc timeouts and rcu
stalls thus hanging the system on 3.19-rc1. Therefore disable it in all cases,
as we expect the devicetree to explicitly select either mmc or jtag pinmuxes
anyway.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 11 Jan 2015 21:07:05 +0000 (13:07 -0800)]
Merge tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin into fixes
Merge "ARM: berlin: Fixes for v3.19 (round 1)" from Sebastian Hesselbarth:
Marvell Berlin fixes for v3.19 round 1:
- SDHCI DT fixes for BG2Q and BG2Q reference board
- BG2Q SM GPIO DT node relocation
* tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij [Fri, 9 Jan 2015 19:11:20 +0000 (20:11 +0100)]
ARM: nomadik: fix up leftover device tree pins
We altered the device tree bindings for the Nomadik family of
pin controllers to be standard, this file was merged out-of-order
so we missed fixing this. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 8 Jan 2015 22:43:00 +0000 (14:43 -0800)]
Merge tag 'omap-for-v3.19/fixes-rc1' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.19-rc1" from Tony Lindgren:
Fixes for omaps mostly to deal with dra7 timer issues
and hypervisor mode. The other fixes are minor fixes for
various boards. The summary of the fixes is:
- Fix real-time counter rate typos for some frequencies
- Fix counter frequency drift for am572x
- Fix booting of secondary CPU in HYP mode
- Fix n900 board name for legacy user space
- Fix cpufreq in omap2plus_defconfig after Kconfig change
- Fix dra7 qspi partitions
And also, let's re-enable smc91x on some n900 boards that
we have sitting in a few test boot systems after the boot
loader dependencies got fixed.
* tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
ARM: OMAP2+: Fix n900 board name for legacy user space
ARM: omap5/dra7xx: Enable booting secondary CPU in HYP mode
ARM: dra7xx: Fix counter frequency drift for AM572x errata i856
ARM: omap5/dra7xx: Fix frequency typos
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 8 Jan 2015 22:42:11 +0000 (14:42 -0800)]
Merge tag 'imx-fixes-3.19' of git://git./linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.19" from Shawn Guo:
The i.MX fixes for 3.19:
- One fix for incorrect i.MX25 SPI1 clock assignment in device tree,
which causes system hang when accessing SPI1.
- Correct i.MX6SX QSPI parent clock configuration to fix a kernel Oops.
- Fix ULPI PHY reset modelling on imx51-babbage board to remove the
dependency on bootloader for USB3317 ULPI PHY reset.
- Correct video divider setting on i.MX6Q rev T0 1.0 to fix the issue
that HDMI is not working at high resolution on T0 1.0.
- One incremental fix for CODA960 VPU enabling in device tree to
correct interrupt order.
- LS1021A SCFG block works in BE mode, add device tree property
big-endian to make it right.
* tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: imx6sx: Set PLL2 as parent of QSPI clocks
ARM: dts: imx25: Fix the SPI1 clocks
ARM: clk-imx6q: fix video divider for rev T0 1.0
ARM: dts: imx6qdl: Fix CODA960 interrupt order
ARM: ls1021a: dtsi: add 'big-endian' property for scfg node
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 8 Jan 2015 22:38:36 +0000 (14:38 -0800)]
Merge tag 'v3.19-rockchip-dtsfixes1' of git://git./linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: dts fix for 3.19" from Heiko Stübner:
Increase drive-strength to sdmmc pins on rk3288-evb to fix
an issue with the fixed highspeed card detection.
* tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: bump sd card pin drive strength up on rk3288-evb
Signed-off-by: Olof Johansson <olof@lixom.net>
Louis Langholtz [Fri, 16 Jan 2015 05:04:46 +0000 (22:04 -0700)]
kernel: avoid overflow in cmp_range
Avoid overflow possibility.
[ The overflow is purely theoretical, since this is used for memory
ranges that aren't even close to using the full 64 bits, but this is
the right thing to do regardless. - Linus ]
Signed-off-by: Louis Langholtz <lou_langholtz@me.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Peter Anvin <hpa@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sukadev Bhattiprolu [Sat, 22 Nov 2014 01:33:53 +0000 (20:33 -0500)]
perf tools powerpc: Use dwfl_report_elf() instead of offline.
dwfl_report_offline() works only when libraries are prelinked.
Replace dwfl_report_offline() with dwfl_report_elf() so we correctly
extract debug info even from libraries that are not prelinked.
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Link: http://lkml.kernel.org/r/20150114221045.GA17703@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Namhyung Kim [Wed, 14 Jan 2015 11:18:05 +0000 (20:18 +0900)]
perf tools: Fix segfault for symbol annotation on TUI
Currently the symbol structure is allocated with symbol_conf.priv_size
to carry sideband information like annotation, map browser on TUI and
sort-by-name tree node. So retrieving these information from symbol
needs to care about the details of such placement.
However the annotation code just assumes that the symbol is placed after
the struct annotation. But actually there's other info between them.
So accessing those struct will lead to an undefined behavior (usually a
crash) after they write their info to the same location.
To reproduce the problem, please follow the steps below:
1. run perf report (TUI of course) with -v option
2. open map browser (by pressing right arrow key for any entry)
3. search any function (by pressing '/' key and input whatever..)
4. return to the hist browser (by pressing 'q' or left arrow key)
5. open annotation window for the same entry (by pressing 'a' key)
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1421234288-22758-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Wang Nan [Wed, 14 Jan 2015 02:36:47 +0000 (10:36 +0800)]
perf test: Fix dwarf unwind using libunwind.
Perf tool fails to unwind user stack if the event raises in a shared
object. This patch improves tests/dwarf-unwind.c to demonstrate the
problem by utilizing commonly used glibc function "bsearch". If perf is
not statically linked, the testcase will try to unwind a mixed call
trace.
By debugging libunwind I found that there is a bug in unwind-libunwind:
it always passes 0 as segbase to libunwind, cause libunwind unable to
locate debug_frame entry fir first level ip address (I add some more
debugging output into libunwind to make things clear):
>_Uarm_dwarf_find_debug_frame: start_ip = 10be98, end_ip = 10c2a4
>_Uarm_dwarf_find_debug_frame: found debug_frame table `/lib/libc-2.18.so': segbase=0x0, len=7, gp=0x0, table_data=0x449388
>_Uarm_dwarf_search_unwind_table: call lookup:ip =
b6cd3bcc, segbase = 0, rel_ip =
b6cd3bcc
>lookup: e->start_ip_offset = bcf18 (rel_ip =
b6cd3bcc)
>lookup: e->start_ip_offset = 6d314 (rel_ip =
b6cd3bcc)
>lookup: e->start_ip_offset = 33d0c (rel_ip =
b6cd3bcc)
...
>lookup: e->start_ip_offset = 15d0c (rel_ip =
b6cd3bcc)
>lookup: e->start_ip_offset = 15c40 (rel_ip =
b6cd3bcc)
>_Uarm_dwarf_search_unwind_table: IP
b6cd3bcc inside range
b6c12000-
b6d4c000, but no explicit unwind info found
>put_rs_cache: unmasking signals/interrupts and releasing lock
>_Uarm_dwarf_step: returning -10
>_Uarm_step: dwarf_step()=-10
This patch passes map->start as segbase to dwarf_find_debug_frame(), so
di will be initialized correctly.
In addition, dso and executable are different when setting segbase. This
patch first check whether the elf is executable, and pass segbase only
for shared object.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1421203007-75799-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Vineet Gupta [Tue, 13 Jan 2015 13:43:22 +0000 (19:13 +0530)]
perf tools: Avoid build splat for syscall numbers with uclibc
This is due to duplicated unistd inclusion (via uClibc headers + kernel headers)
Also seen on ARM uClibc based tools
------- ARC build ---------->8-------------
CC util/evlist.o
In file included from
~/arc/k.org/arch/arc/include/uapi/asm/unistd.h:25:0,
from util/../perf-sys.h:10,
from util/../perf.h:15,
from util/event.h:7,
from util/event.c:3:
~/arc/k.org/include/uapi/asm-generic/unistd.h:906:0:
warning: "__NR_fcntl64" redefined [enabled by default]
#define __NR_fcntl64 __NR3264_fcntl
^
In file included from
~/arc/gnu/INSTALL_1412-arc-2014.12-rc1/arc-snps-linux-uclibc/sysroot/usr/include/sys/syscall.h:24:0,
from util/../perf-sys.h:6,
----------------->8-------------------
------- ARM build ---------->8-------------
CC FPIC plugin_scsi.o
In file included from util/../perf-sys.h:9:0,
from util/../perf.h:15,
from util/cache.h:7,
from perf.c:12:
~/arc/k.org/arch/arm/include/uapi/asm/unistd.h:28:0:
warning: "__NR_restart_syscall" redefined [enabled by default]
In file included from
~/buildroot/host/usr/arm-buildroot-linux-uclibcgnueabi/sysroot/usr/include/sys/syscall.h:25:0,
from util/../perf-sys.h:6,
from util/../perf.h:15,
from util/cache.h:7,
from perf.c:12:
~/buildroot/host/usr/arm-buildroot-linux-uclibcgnueabi/sysroot/usr/include/bits/sysnum.h:17:0:
note: this is the location of the previous definition
----------------->8-------------------
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1421156604-30603-4-git-send-email-vgupta@synopsys.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Vineet Gupta [Tue, 13 Jan 2015 13:43:21 +0000 (19:13 +0530)]
perf tools: Elide strlcpy warning with uclibc
----------------->8------------------
CC bench/sched-pipe.o
In file included from builtin-annotate.c:13:0:
util/cache.h:76:15: warning: redundant redeclaration of 'strlcpy'
[-Wredundant-decls]
extern size_t strlcpy(char *dest, const char *src, size_t size);
^
In file included from util/util.h:55:0,
from builtin.h:4,
from builtin-annotate.c:8:
~/vineetg/arc/gnu/INSTALL_1412-arc-2014.12-rc1/arc-snps-linux-uclibc/sysroot/usr/include/string.h:396:15:
note: previous declaration of 'strlcpy' was here
extern size_t strlcpy(char *__restrict dst, const char *__restrict src,
----------------->8------------------
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1421156604-30603-3-git-send-email-vgupta@synopsys.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Alexey Brodkin [Sat, 10 Jan 2015 11:10:50 +0000 (16:40 +0530)]
perf tools: Fix statfs.f_type data type mismatch build error with uclibc
ARC Linux uses the no legacy syscalls abi and corresponding uClibc headers
statfs defines f_type to be U32 which causes perf build breakage
http://git.uclibc.org/uClibc/tree/libc/sysdeps/linux/common-generic/bits/statfs.h
----------->8---------------
CC fs/fs.o
fs/fs.c: In function 'fs__valid_mount':
fs/fs.c:82:24: error: comparison between signed and unsigned integer
expressions [-Werror=sign-compare]
else if (st_fs.f_type != magic)
^
cc1: all warnings being treated as errors
----------->8---------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Cody P Schafer <dev@codyps.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Link: http://lkml.kernel.org/r/1420888254-17504-2-git-send-email-vgupta@synopsys.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Tue, 13 Jan 2015 13:19:12 +0000 (10:19 -0300)]
tools: Remove bitops/hweight usage of bits in tools/perf
We need to use lib/hweight.c for that, just like we do for lib/rbtree.c,
so tools need to link hweight.o. For now do it directly, but we need to
have a tools/lib/lk.a or .so that collects these goodies...
Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-a1e91dx3apzqw5kbdt7ut21s@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Namhyung Kim [Fri, 9 Jan 2015 00:38:12 +0000 (09:38 +0900)]
perf machine: Fix __machine__findnew_thread() error path
When thread__init_map_groups() fails, a new thread should be removed
from the rbtree since it's gonna be freed. Also update last match cache
only if the function succeeded.
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1420763892-15535-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Namhyung Kim [Mon, 12 Jan 2015 02:20:55 +0000 (10:20 +0800)]
perf tools: Fix building error in x86_64 when dwarf unwind is on
When build with 'make ARCH=x86' and dwarf unwind is on, there is a
compiling error:
CC /home/wn/perf/arch/x86/util/unwind-libdw.o
CC /home/wn/perf/arch/x86/tests/regs_load.o
arch/x86/tests/regs_load.S: Assembler messages:
arch/x86/tests/regs_load.S:65: Error: operand type mismatch for `push'
arch/x86/tests/regs_load.S:72: Error: operand type mismatch for `pop'
make[1]: *** [/home/wn/perf/arch/x86/tests/regs_load.o] Error 1
make[1]: INTERNAL: Exiting with 25 jobserver tokens available; should be 24!
make: *** [all] Error 2
...
Which is caused by incorrectly undefine macro HAVE_ARCH_X86_64_SUPPORT.
'config/Makefile.arch' tests __x86_64__ only when 'ARCH=x86_64'.
However, when building x86_64 kernel, ARCH=x86 is valid and commonly
used. Build systems, such as yocto, uses x86_64 compiler with 'ARCH=x86'
to build x86_64 perf, which causes mismatching.
As __LP64__ is defined for x86_64 as well, we can consolidate the
__x86_64__ check to the __LP64__ check and get rid of the IS_X86_64
IMHO.
(This patch is made by Namhyung Kim when replying my v1 patch:
https://lkml.org/lkml/2015/1/7/17
I modified the code to remove dependency on RAW_ARCH:
https://lkml.org/lkml/2015/1/7/865
Namhyung Kim didn't provide his SOB in his original email. I add
mine only for my modification.)
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1421029255-23039-1-git-send-email-wangnan0@huawei.com
[ Namhyung provided his S-o-B on a followup to this patch thread on lkml ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Namhyung Kim [Sat, 10 Jan 2015 10:33:48 +0000 (19:33 +0900)]
perf probe: Propagate error code when write(2) failed
When it failed to write probe commands to the probe_event file in
debugfs, it needs to propagate the error code properly. Current code
blindly uses the return value of the write(2) so it always uses
-1 (-EPERM) and it might confuse users.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1420886028-15135-4-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Fri, 16 Jan 2015 19:18:08 +0000 (08:18 +1300)]
Merge tag 'char-misc-3.19-rc5' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are three small driver fixes for reported issues for 3.19-rc5.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mcb: mcb-pci: Only remap the 1st 0x200 bytes of BAR 0
mei: add ABI documentation for fw_status exported through sysfs
mei: clean reset bit before reset
Linus Torvalds [Fri, 16 Jan 2015 19:16:52 +0000 (08:16 +1300)]
Merge tag 'driver-core-3.19-rc5' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is one kernfs fix for a reported issue for 3.19-rc5.
It has been in linux-next for a while"
* tag 'driver-core-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: Fix kernfs_name_compare
Linus Torvalds [Fri, 16 Jan 2015 19:15:49 +0000 (08:15 +1300)]
Merge tag 'tty-3.19-rc5' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some tty and serial driver fixes for 3.19-rc5 that resolve
some reported issues, and add a new device id to the 8250 serial port
driver.
All have been in linux-next with no reported problems"
* tag 'tty-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: samsung: Add the support for Exynos5433 SoC
Revert "tty: Fix pty master poll() after slave closes v2"
tty: Prevent hw state corruption in exclusive mode reopen
tty: Add support for the WCH384 4S multi-IO card
serial: fix parisc boot hang
Linus Torvalds [Fri, 16 Jan 2015 19:13:45 +0000 (08:13 +1300)]
Merge tag 'staging-3.19-rc5' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are 6 staging driver fixes for 3.19-rc5.
They fix some reported issues with some IIO drivers, as well as some
issues with the vt6655 wireless driver.
All have been in linux-next for a while"
* tag 'staging-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: fix sparse warning: argument type
staging: vt6655: Fix loss of distant/weak access points on channel change.
staging: vt6655: vnt_tx_packet Fix corrupted tx packets.
staging: vt6655: fix sparse warnings: incorrect argument type
iio: iio: Fix iio_channel_read return if channel havn't info
iio: ad799x: Fix ad7991/ad7995/ad7999 config setup
Linus Torvalds [Fri, 16 Jan 2015 19:02:44 +0000 (08:02 +1300)]
Merge tag 'usb-3.19-rc5' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a bunch of USB fixes for 3.19-rc5.
Most of these are gadget driver fixes, along with the xhci driver fix
that we both reported having problems with, as well as some new device
ids and other tiny fixes.
All have been in linux-next with no problems"
* tag 'usb-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
usb: dwc3: gadget: Stop TRB preparation after limit is reached
usb: dwc3: gadget: Fix TRB preparation during SG
usb: phy: mv-usb: fix usb_phy build errors
usb: serial: handle -ENODEV quietly in generic_submit_read_urb
usb: serial: silence all non-critical read errors
USB: console: fix potential use after free
USB: console: fix uninitialised ldisc semaphore
usb: gadget: udc: atmel: fix possible oops when unloading module
usb: gadget: gadgetfs: fix an oops in ep_write()
usb: phy: Fix deferred probing
OHCI: add a quirk for ULi M5237 blocking on reset
uas: Add US_FL_NO_ATA_1X for 2 more Seagate disk enclosures
uas: Do not blacklist ASM1153 disk enclosures
usb: gadget: udc: avoid dereference before NULL check in ep_queue
usb: host: ehci-tegra: request deferred probe when failing to get phy
uas: disable UAS on Apricorn SATA dongles
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS566 with usb-id 0bc2:a013
uas: Add US_FL_NO_ATA_1X for Seagate devices with usb-id 0bc2:a013
xhci: Add broken-streams quirk for Fresco Logic FL1000G xhci controllers
USB: EHCI: adjust error return code
...
Linus Torvalds [Fri, 16 Jan 2015 19:01:21 +0000 (08:01 +1300)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Wire up compat_sys_execveat for compat (AArch32) tasks
- Revert
421520ba9829, as this breaks our side of the boot protocol
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: partially revert "ARM: 8167/1: extend the reserved memory for initrd to be page aligned"
arm64: compat: wire up compat_sys_execveat
Linus Torvalds [Fri, 16 Jan 2015 18:59:06 +0000 (07:59 +1300)]
Merge tag 'nfs-for-3.19-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Stable fix for a NFSv3/lockd race
- Fixes for several NFSv4.1 client id trunking bugs
- Remove an incorrect test when checking for delegated opens"
* tag 'nfs-for-3.19-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Remove incorrect check in can_open_delegated()
NFS: Ignore transport protocol when detecting server trunking
NFSv4/v4.1: Verify the client owner id during trunking detection
NFSv4: Cache the NFSv4/v4.1 client owner_id in the struct nfs_client
NFSv4.1: Fix client id trunking on Linux
LOCKD: Fix a race when initialising nlmsvc_timeout
Linus Torvalds [Fri, 16 Jan 2015 18:55:52 +0000 (07:55 +1300)]
Merge tag 'trace-fixes-v3.19-rc3' of git://git./linux/kernel/git/rostedt/linux-trace
Pull ftrace fixes from Steven Rostedt:
"This holds a few fixes to the ftrace infrastructure as well as the
mixture of function graph tracing and kprobes.
When jprobes and function graph tracing is enabled at the same time it
will crash the system:
# modprobe jprobe_example
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
After the first fork (jprobe_example probes it), the system will
crash.
This is due to the way jprobes copies the stack frame and does not do
a normal function return. This messes up with the function graph
tracing accounting which hijacks the return address from the stack and
replaces it with a hook function. It saves the return addresses in a
separate stack to put back the correct return address when done. But
because the jprobe functions do not do a normal return, their stack
addresses are not put back until the function they probe is called,
which means that the probed function will get the return address of
the jprobe handler instead of its own.
The simple fix here was to disable function graph tracing while the
jprobe handler is being called.
While debugging this I found two minor bugs with the function graph
tracing.
The first was about the function graph tracer sharing its function
hash with the function tracer (they both get filtered by the same
input). The changing of the set_ftrace_filter would not sync the
function recording records after a change if the function tracer was
disabled but the function graph tracer was enabled. This was due to
the update only checking one of the ops instead of the shared ops to
see if they were enabled and should perform the sync. This caused the
ftrace accounting to break and a ftrace_bug() would be triggered,
disabling ftrace until a reboot.
The second was that the check to update records only checked one of
the filter hashes. It needs to test both the "filter" and "notrace"
hashes. The "filter" hash determines what functions to trace where as
the "notrace" hash determines what functions not to trace (trace all
but these). Both hashes need to be passed to the update code to find
out what change is being done during the update. This also broke the
ftrace record accounting and triggered a ftrace_bug().
This patch set also include two more fixes that were reported
separately from the kprobe issue.
One was that init_ftrace_syscalls() was called twice at boot up. This
is not a major bug, but that call performed a rather large kmalloc
(NR_syscalls * sizeof(*syscalls_metadata)). The second call made the
first one a memory leak, and wastes memory.
The other fix is a regression caused by an update in the v3.19 merge
window. The moving to enable events early, moved the enabling before
PID 1 was created. The syscall events require setting the
TIF_SYSCALL_TRACEPOINT for all tasks. But for_each_process_thread()
does not include the swapper task (PID 0), and ended up being a nop.
A suggested fix was to add the init_task() to have its flag set, but I
didn't really want to mess with PID 0 for this minor bug. Instead I
disable and re-enable events again at early_initcall() where it use to
be enabled. This also handles any other event that might have its own
reg function that could break at early boot up"
* tag 'trace-fixes-v3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix enabling of syscall events on the command line
tracing: Remove extra call to init_ftrace_syscalls()
ftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing
ftrace: Check both notrace and filter for old hash
ftrace: Fix updating of filters for shared global_ops filters
Catalin Marinas [Fri, 16 Jan 2015 13:56:38 +0000 (13:56 +0000)]
arm64: partially revert "ARM: 8167/1: extend the reserved memory for initrd to be page aligned"
This patch partially reverts commit
421520ba98290a73b35b7644e877a48f18e06004
(only the arm64 part). There is no guarantee that the boot-loader places other
images like dtb in a different page than initrd start/end, especially when the
kernel is built with 64KB pages. When this happens, such pages must not be
freed. The free_reserved_area() already takes care of rounding up "start" and
rounding down "end" to avoid freeing partially used pages.
Cc: <stable@vger.kernel.org> # 3.17+
Reported-by: Peter Maydell <Peter.Maydell@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>