OSDN Git Service
Vladimir Oltean [Wed, 5 Jan 2022 13:21:38 +0000 (15:21 +0200)]
net: dsa: merge all bools of struct dsa_switch into a single u32
struct dsa_switch has 9 boolean properties, many of which are in fact
set by drivers for custom behavior (vlan_filtering_is_global,
needs_standalone_vlan_filtering, etc etc). The binary layout of the
structure could be improved. For example, the "bool setup" at the
beginning introduces a gratuitous 7 byte hole in the first cache line.
The change merges all boolean properties into bitfields of an u32, and
places that u32 in the first cache line of the structure, since many
bools are accessed from the data path (untag_bridge_pvid, vlan_filtering,
vlan_filtering_is_global).
We place this u32 after the existing ds->index, which is also 4 bytes in
size. As a positive side effect, ds->tagger_data now fits into the first
cache line too, because 4 bytes are saved.
Before:
pahole -C dsa_switch net/dsa/slave.o
struct dsa_switch {
bool setup; /* 0 1 */
/* XXX 7 bytes hole, try to pack */
struct device * dev; /* 8 8 */
struct dsa_switch_tree * dst; /* 16 8 */
unsigned int index; /* 24 4 */
/* XXX 4 bytes hole, try to pack */
struct notifier_block nb; /* 32 24 */
/* XXX last struct has 4 bytes of padding */
void * priv; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
void * tagger_data; /* 64 8 */
struct dsa_chip_data * cd; /* 72 8 */
const struct dsa_switch_ops * ops; /* 80 8 */
u32 phys_mii_mask; /* 88 4 */
/* XXX 4 bytes hole, try to pack */
struct mii_bus * slave_mii_bus; /* 96 8 */
unsigned int ageing_time_min; /* 104 4 */
unsigned int ageing_time_max; /* 108 4 */
struct dsa_8021q_context * tag_8021q_ctx; /* 112 8 */
struct devlink * devlink; /* 120 8 */
/* --- cacheline 2 boundary (128 bytes) --- */
unsigned int num_tx_queues; /* 128 4 */
bool vlan_filtering_is_global; /* 132 1 */
bool needs_standalone_vlan_filtering; /* 133 1 */
bool configure_vlan_while_not_filtering; /* 134 1 */
bool untag_bridge_pvid; /* 135 1 */
bool assisted_learning_on_cpu_port; /* 136 1 */
bool vlan_filtering; /* 137 1 */
bool pcs_poll; /* 138 1 */
bool mtu_enforcement_ingress; /* 139 1 */
unsigned int num_lag_ids; /* 140 4 */
unsigned int max_num_bridges; /* 144 4 */
/* XXX 4 bytes hole, try to pack */
size_t num_ports; /* 152 8 */
/* size: 160, cachelines: 3, members: 27 */
/* sum members: 141, holes: 4, sum holes: 19 */
/* paddings: 1, sum paddings: 4 */
/* last cacheline: 32 bytes */
};
After:
pahole -C dsa_switch net/dsa/slave.o
struct dsa_switch {
struct device * dev; /* 0 8 */
struct dsa_switch_tree * dst; /* 8 8 */
unsigned int index; /* 16 4 */
u32 setup:1; /* 20: 0 4 */
u32 vlan_filtering_is_global:1; /* 20: 1 4 */
u32 needs_standalone_vlan_filtering:1; /* 20: 2 4 */
u32 configure_vlan_while_not_filtering:1; /* 20: 3 4 */
u32 untag_bridge_pvid:1; /* 20: 4 4 */
u32 assisted_learning_on_cpu_port:1; /* 20: 5 4 */
u32 vlan_filtering:1; /* 20: 6 4 */
u32 pcs_poll:1; /* 20: 7 4 */
u32 mtu_enforcement_ingress:1; /* 20: 8 4 */
/* XXX 23 bits hole, try to pack */
struct notifier_block nb; /* 24 24 */
/* XXX last struct has 4 bytes of padding */
void * priv; /* 48 8 */
void * tagger_data; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct dsa_chip_data * cd; /* 64 8 */
const struct dsa_switch_ops * ops; /* 72 8 */
u32 phys_mii_mask; /* 80 4 */
/* XXX 4 bytes hole, try to pack */
struct mii_bus * slave_mii_bus; /* 88 8 */
unsigned int ageing_time_min; /* 96 4 */
unsigned int ageing_time_max; /* 100 4 */
struct dsa_8021q_context * tag_8021q_ctx; /* 104 8 */
struct devlink * devlink; /* 112 8 */
unsigned int num_tx_queues; /* 120 4 */
unsigned int num_lag_ids; /* 124 4 */
/* --- cacheline 2 boundary (128 bytes) --- */
unsigned int max_num_bridges; /* 128 4 */
/* XXX 4 bytes hole, try to pack */
size_t num_ports; /* 136 8 */
/* size: 144, cachelines: 3, members: 27 */
/* sum members: 132, holes: 2, sum holes: 8 */
/* sum bitfield members: 9 bits, bit holes: 1, sum bit holes: 23 bits */
/* paddings: 1, sum paddings: 4 */
/* last cacheline: 16 bytes */
};
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 5 Jan 2022 13:21:37 +0000 (15:21 +0200)]
net: dsa: move dsa_port :: type near dsa_port :: index
Both dsa_port :: type and dsa_port :: index introduce a 4 octet hole
after them, so we can group them together and the holes would be
eliminated, turning 16 octets of storage into just 8. This makes the
cpu_dp pointer fit in the first cache line, which is good, because
dsa_slave_to_master(), called by dsa_enqueue_skb(), uses it.
Before:
pahole -C dsa_port net/dsa/slave.o
struct dsa_port {
union {
struct net_device * master; /* 0 8 */
struct net_device * slave; /* 0 8 */
}; /* 0 8 */
const struct dsa_device_ops * tag_ops; /* 8 8 */
struct dsa_switch_tree * dst; /* 16 8 */
struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */
enum {
DSA_PORT_TYPE_UNUSED = 0,
DSA_PORT_TYPE_CPU = 1,
DSA_PORT_TYPE_DSA = 2,
DSA_PORT_TYPE_USER = 3,
} type; /* 32 4 */
/* XXX 4 bytes hole, try to pack */
struct dsa_switch * ds; /* 40 8 */
unsigned int index; /* 48 4 */
/* XXX 4 bytes hole, try to pack */
const char * name; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct dsa_port * cpu_dp; /* 64 8 */
u8 mac[6]; /* 72 6 */
u8 stp_state; /* 78 1 */
u8 vlan_filtering:1; /* 79: 0 1 */
u8 learning:1; /* 79: 1 1 */
u8 lag_tx_enabled:1; /* 79: 2 1 */
u8 devlink_port_setup:1; /* 79: 3 1 */
u8 setup:1; /* 79: 4 1 */
/* XXX 3 bits hole, try to pack */
struct device_node * dn; /* 80 8 */
unsigned int ageing_time; /* 88 4 */
/* XXX 4 bytes hole, try to pack */
struct dsa_bridge * bridge; /* 96 8 */
struct devlink_port devlink_port; /* 104 288 */
/* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */
struct phylink * pl; /* 392 8 */
struct phylink_config pl_config; /* 400 40 */
struct net_device * lag_dev; /* 440 8 */
/* --- cacheline 7 boundary (448 bytes) --- */
struct net_device * hsr_dev; /* 448 8 */
struct list_head list; /* 456 16 */
const struct ethtool_ops * orig_ethtool_ops; /* 472 8 */
const struct dsa_netdevice_ops * netdev_ops; /* 480 8 */
struct mutex addr_lists_lock; /* 488 32 */
/* --- cacheline 8 boundary (512 bytes) was 8 bytes ago --- */
struct list_head fdbs; /* 520 16 */
struct list_head mdbs; /* 536 16 */
/* size: 552, cachelines: 9, members: 30 */
/* sum members: 539, holes: 3, sum holes: 12 */
/* sum bitfield members: 5 bits, bit holes: 1, sum bit holes: 3 bits */
/* last cacheline: 40 bytes */
};
After:
pahole -C dsa_port net/dsa/slave.o
struct dsa_port {
union {
struct net_device * master; /* 0 8 */
struct net_device * slave; /* 0 8 */
}; /* 0 8 */
const struct dsa_device_ops * tag_ops; /* 8 8 */
struct dsa_switch_tree * dst; /* 16 8 */
struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */
struct dsa_switch * ds; /* 32 8 */
unsigned int index; /* 40 4 */
enum {
DSA_PORT_TYPE_UNUSED = 0,
DSA_PORT_TYPE_CPU = 1,
DSA_PORT_TYPE_DSA = 2,
DSA_PORT_TYPE_USER = 3,
} type; /* 44 4 */
const char * name; /* 48 8 */
struct dsa_port * cpu_dp; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
u8 mac[6]; /* 64 6 */
u8 stp_state; /* 70 1 */
u8 vlan_filtering:1; /* 71: 0 1 */
u8 learning:1; /* 71: 1 1 */
u8 lag_tx_enabled:1; /* 71: 2 1 */
u8 devlink_port_setup:1; /* 71: 3 1 */
u8 setup:1; /* 71: 4 1 */
/* XXX 3 bits hole, try to pack */
struct device_node * dn; /* 72 8 */
unsigned int ageing_time; /* 80 4 */
/* XXX 4 bytes hole, try to pack */
struct dsa_bridge * bridge; /* 88 8 */
struct devlink_port devlink_port; /* 96 288 */
/* --- cacheline 6 boundary (384 bytes) --- */
struct phylink * pl; /* 384 8 */
struct phylink_config pl_config; /* 392 40 */
struct net_device * lag_dev; /* 432 8 */
struct net_device * hsr_dev; /* 440 8 */
/* --- cacheline 7 boundary (448 bytes) --- */
struct list_head list; /* 448 16 */
const struct ethtool_ops * orig_ethtool_ops; /* 464 8 */
const struct dsa_netdevice_ops * netdev_ops; /* 472 8 */
struct mutex addr_lists_lock; /* 480 32 */
/* --- cacheline 8 boundary (512 bytes) --- */
struct list_head fdbs; /* 512 16 */
struct list_head mdbs; /* 528 16 */
/* size: 544, cachelines: 9, members: 30 */
/* sum members: 539, holes: 1, sum holes: 4 */
/* sum bitfield members: 5 bits, bit holes: 1, sum bit holes: 3 bits */
/* last cacheline: 32 bytes */
};
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 5 Jan 2022 13:21:36 +0000 (15:21 +0200)]
net: dsa: merge all bools of struct dsa_port into a single u8
struct dsa_port has 5 bool members which create quite a number of 7 byte
holes in the structure layout. By merging them all into bitfields of an
u8, and placing that u8 in the 1-byte hole after dp->mac and dp->stp_state,
we can reduce the structure size from 576 bytes to 552 bytes on arm64.
Before:
pahole -C dsa_port net/dsa/slave.o
struct dsa_port {
union {
struct net_device * master; /* 0 8 */
struct net_device * slave; /* 0 8 */
}; /* 0 8 */
const struct dsa_device_ops * tag_ops; /* 8 8 */
struct dsa_switch_tree * dst; /* 16 8 */
struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */
enum {
DSA_PORT_TYPE_UNUSED = 0,
DSA_PORT_TYPE_CPU = 1,
DSA_PORT_TYPE_DSA = 2,
DSA_PORT_TYPE_USER = 3,
} type; /* 32 4 */
/* XXX 4 bytes hole, try to pack */
struct dsa_switch * ds; /* 40 8 */
unsigned int index; /* 48 4 */
/* XXX 4 bytes hole, try to pack */
const char * name; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct dsa_port * cpu_dp; /* 64 8 */
u8 mac[6]; /* 72 6 */
u8 stp_state; /* 78 1 */
/* XXX 1 byte hole, try to pack */
struct device_node * dn; /* 80 8 */
unsigned int ageing_time; /* 88 4 */
bool vlan_filtering; /* 92 1 */
bool learning; /* 93 1 */
/* XXX 2 bytes hole, try to pack */
struct dsa_bridge * bridge; /* 96 8 */
struct devlink_port devlink_port; /* 104 288 */
/* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */
bool devlink_port_setup; /* 392 1 */
/* XXX 7 bytes hole, try to pack */
struct phylink * pl; /* 400 8 */
struct phylink_config pl_config; /* 408 40 */
/* --- cacheline 7 boundary (448 bytes) --- */
struct net_device * lag_dev; /* 448 8 */
bool lag_tx_enabled; /* 456 1 */
/* XXX 7 bytes hole, try to pack */
struct net_device * hsr_dev; /* 464 8 */
struct list_head list; /* 472 16 */
const struct ethtool_ops * orig_ethtool_ops; /* 488 8 */
const struct dsa_netdevice_ops * netdev_ops; /* 496 8 */
struct mutex addr_lists_lock; /* 504 32 */
/* --- cacheline 8 boundary (512 bytes) was 24 bytes ago --- */
struct list_head fdbs; /* 536 16 */
struct list_head mdbs; /* 552 16 */
bool setup; /* 568 1 */
/* size: 576, cachelines: 9, members: 30 */
/* sum members: 544, holes: 6, sum holes: 25 */
/* padding: 7 */
};
After:
pahole -C dsa_port net/dsa/slave.o
struct dsa_port {
union {
struct net_device * master; /* 0 8 */
struct net_device * slave; /* 0 8 */
}; /* 0 8 */
const struct dsa_device_ops * tag_ops; /* 8 8 */
struct dsa_switch_tree * dst; /* 16 8 */
struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */
enum {
DSA_PORT_TYPE_UNUSED = 0,
DSA_PORT_TYPE_CPU = 1,
DSA_PORT_TYPE_DSA = 2,
DSA_PORT_TYPE_USER = 3,
} type; /* 32 4 */
/* XXX 4 bytes hole, try to pack */
struct dsa_switch * ds; /* 40 8 */
unsigned int index; /* 48 4 */
/* XXX 4 bytes hole, try to pack */
const char * name; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct dsa_port * cpu_dp; /* 64 8 */
u8 mac[6]; /* 72 6 */
u8 stp_state; /* 78 1 */
u8 vlan_filtering:1; /* 79: 0 1 */
u8 learning:1; /* 79: 1 1 */
u8 lag_tx_enabled:1; /* 79: 2 1 */
u8 devlink_port_setup:1; /* 79: 3 1 */
u8 setup:1; /* 79: 4 1 */
/* XXX 3 bits hole, try to pack */
struct device_node * dn; /* 80 8 */
unsigned int ageing_time; /* 88 4 */
/* XXX 4 bytes hole, try to pack */
struct dsa_bridge * bridge; /* 96 8 */
struct devlink_port devlink_port; /* 104 288 */
/* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */
struct phylink * pl; /* 392 8 */
struct phylink_config pl_config; /* 400 40 */
struct net_device * lag_dev; /* 440 8 */
/* --- cacheline 7 boundary (448 bytes) --- */
struct net_device * hsr_dev; /* 448 8 */
struct list_head list; /* 456 16 */
const struct ethtool_ops * orig_ethtool_ops; /* 472 8 */
const struct dsa_netdevice_ops * netdev_ops; /* 480 8 */
struct mutex addr_lists_lock; /* 488 32 */
/* --- cacheline 8 boundary (512 bytes) was 8 bytes ago --- */
struct list_head fdbs; /* 520 16 */
struct list_head mdbs; /* 536 16 */
/* size: 552, cachelines: 9, members: 30 */
/* sum members: 539, holes: 3, sum holes: 12 */
/* sum bitfield members: 5 bits, bit holes: 1, sum bit holes: 3 bits */
/* last cacheline: 40 bytes */
};
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 5 Jan 2022 13:21:35 +0000 (15:21 +0200)]
net: dsa: move dsa_port :: stp_state near dsa_port :: mac
The MAC address of a port is 6 octets in size, and this creates a 2
octet hole after it. There are some other u8 members of struct dsa_port
that we can put in that hole. One such member is the stp_state.
Before:
pahole -C dsa_port net/dsa/slave.o
struct dsa_port {
union {
struct net_device * master; /* 0 8 */
struct net_device * slave; /* 0 8 */
}; /* 0 8 */
const struct dsa_device_ops * tag_ops; /* 8 8 */
struct dsa_switch_tree * dst; /* 16 8 */
struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */
enum {
DSA_PORT_TYPE_UNUSED = 0,
DSA_PORT_TYPE_CPU = 1,
DSA_PORT_TYPE_DSA = 2,
DSA_PORT_TYPE_USER = 3,
} type; /* 32 4 */
/* XXX 4 bytes hole, try to pack */
struct dsa_switch * ds; /* 40 8 */
unsigned int index; /* 48 4 */
/* XXX 4 bytes hole, try to pack */
const char * name; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct dsa_port * cpu_dp; /* 64 8 */
u8 mac[6]; /* 72 6 */
/* XXX 2 bytes hole, try to pack */
struct device_node * dn; /* 80 8 */
unsigned int ageing_time; /* 88 4 */
bool vlan_filtering; /* 92 1 */
bool learning; /* 93 1 */
u8 stp_state; /* 94 1 */
/* XXX 1 byte hole, try to pack */
struct dsa_bridge * bridge; /* 96 8 */
struct devlink_port devlink_port; /* 104 288 */
/* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */
bool devlink_port_setup; /* 392 1 */
/* XXX 7 bytes hole, try to pack */
struct phylink * pl; /* 400 8 */
struct phylink_config pl_config; /* 408 40 */
/* --- cacheline 7 boundary (448 bytes) --- */
struct net_device * lag_dev; /* 448 8 */
bool lag_tx_enabled; /* 456 1 */
/* XXX 7 bytes hole, try to pack */
struct net_device * hsr_dev; /* 464 8 */
struct list_head list; /* 472 16 */
const struct ethtool_ops * orig_ethtool_ops; /* 488 8 */
const struct dsa_netdevice_ops * netdev_ops; /* 496 8 */
struct mutex addr_lists_lock; /* 504 32 */
/* --- cacheline 8 boundary (512 bytes) was 24 bytes ago --- */
struct list_head fdbs; /* 536 16 */
struct list_head mdbs; /* 552 16 */
bool setup; /* 568 1 */
/* size: 576, cachelines: 9, members: 30 */
/* sum members: 544, holes: 6, sum holes: 25 */
/* padding: 7 */
};
After:
pahole -C dsa_port net/dsa/slave.o
struct dsa_port {
union {
struct net_device * master; /* 0 8 */
struct net_device * slave; /* 0 8 */
}; /* 0 8 */
const struct dsa_device_ops * tag_ops; /* 8 8 */
struct dsa_switch_tree * dst; /* 16 8 */
struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */
enum {
DSA_PORT_TYPE_UNUSED = 0,
DSA_PORT_TYPE_CPU = 1,
DSA_PORT_TYPE_DSA = 2,
DSA_PORT_TYPE_USER = 3,
} type; /* 32 4 */
/* XXX 4 bytes hole, try to pack */
struct dsa_switch * ds; /* 40 8 */
unsigned int index; /* 48 4 */
/* XXX 4 bytes hole, try to pack */
const char * name; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
struct dsa_port * cpu_dp; /* 64 8 */
u8 mac[6]; /* 72 6 */
u8 stp_state; /* 78 1 */
/* XXX 1 byte hole, try to pack */
struct device_node * dn; /* 80 8 */
unsigned int ageing_time; /* 88 4 */
bool vlan_filtering; /* 92 1 */
bool learning; /* 93 1 */
/* XXX 2 bytes hole, try to pack */
struct dsa_bridge * bridge; /* 96 8 */
struct devlink_port devlink_port; /* 104 288 */
/* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */
bool devlink_port_setup; /* 392 1 */
/* XXX 7 bytes hole, try to pack */
struct phylink * pl; /* 400 8 */
struct phylink_config pl_config; /* 408 40 */
/* --- cacheline 7 boundary (448 bytes) --- */
struct net_device * lag_dev; /* 448 8 */
bool lag_tx_enabled; /* 456 1 */
/* XXX 7 bytes hole, try to pack */
struct net_device * hsr_dev; /* 464 8 */
struct list_head list; /* 472 16 */
const struct ethtool_ops * orig_ethtool_ops; /* 488 8 */
const struct dsa_netdevice_ops * netdev_ops; /* 496 8 */
struct mutex addr_lists_lock; /* 504 32 */
/* --- cacheline 8 boundary (512 bytes) was 24 bytes ago --- */
struct list_head fdbs; /* 536 16 */
struct list_head mdbs; /* 552 16 */
bool setup; /* 568 1 */
/* size: 576, cachelines: 9, members: 30 */
/* sum members: 544, holes: 6, sum holes: 25 */
/* padding: 7 */
};
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 5 Jan 2022 14:36:37 +0000 (14:36 +0000)]
Merge branch 'hns3-stats-refactor'
Jie Wang says:
====================
net: hns3: refactor rss/tqp stats functions
Currently, hns3 PF and VF module have two sets of rss and tqp stats APIs
to provide get and set functions. Most of these APIs are the same. There is
no need to keep these two sets of same functions for double development and
bugfix work.
This series refactor the rss and tqp stats APIs in hns3 PF and VF by
implementing one set of common APIs for PF and VF reuse and deleting the
old APIs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:15 +0000 (22:20 +0800)]
net: hns3: create new common cmd code for PF and VF modules
Currently PF and VF use two sets of command code for modules to interact
with firmware. These codes values are same espect the macro names. It is
redundent to keep two sets of command code for same functions between PF
and VF.
So this patch firstly creates a unified command code for PF and VF module.
We keep the macro name same with the PF command code name to avoid too many
meaningless modifications. Secondly the new common command codes are used
to replace the old ones in VF and deletes the old ones.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:14 +0000 (22:20 +0800)]
net: hns3: refactor VF tqp stats APIs with new common tqp stats APIs
This patch firstly uses new tqp struct(hclge_comm_tqp) and removes the
old VF tqp struct(hclgevf_tqp). All the tqp stats members used in VF module
are modified according to the new hclge_comm_tqp.
Secondly VF tqp stats APIs are refactored to use new common tqp stats APIs.
The old tqp stats APIs in VF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:13 +0000 (22:20 +0800)]
net: hns3: refactor PF tqp stats APIs with new common tqp stats APIs
This patch firstly uses new tqp struct(hclge_comm_tqp) and deletes the
old PF tqp struct(hclge_tqp). All the tqp stats members used in PF module
are modified according to the new hclge_comm_tqp.
Secondly PF tqp stats APIs are refactored to use new common tqp stats APIs.
The old tqp stats APIs in PF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:12 +0000 (22:20 +0800)]
net: hns3: create new set of common tqp stats APIs for PF and VF reuse
This patch creates new set of common tqp stats structures and APIs for PF
and VF tqp stats module. Subfunctions such as get tqp stats, update tqp
stats and reset tqp stats are inclued in this patch.
These new common tqp stats APIs will be used to replace the old PF and VF
tqp stats APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:11 +0000 (22:20 +0800)]
net: hns3: refactor VF rss init APIs with new common rss init APIs
This patch uses common rss init APIs to replace the old APIs in VF rss
module and removes the old VF rss init APIs. Several related Subfunctions
and macros are also modified in this patch.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:10 +0000 (22:20 +0800)]
net: hns3: refactor PF rss init APIs with new common rss init APIs
This patch uses common rss init APIs to replace the old APIs in PF rss
module and deletes the old PF rss init APIs. Some related subfunctions and
macros are also modified in this patch.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:09 +0000 (22:20 +0800)]
net: hns3: create new set of common rss init APIs for PF and VF reuse
This patch creates new set of common rss init APIs for PF and VF rss
module. Subfunctions called by rss init process are also created include
rss tuple configuration and rss indirect table configuration.
These new common rss init APIs will be used to replace the old PF and VF
rss init APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:08 +0000 (22:20 +0800)]
net: hns3: refactor VF rss set APIs with new common rss set APIs
This patch uses new common rss set APIs to replace the old APIs in VF rss
module and removes those old rss set APIs. The related macros in VF are
also modified.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:07 +0000 (22:20 +0800)]
net: hns3: refactor PF rss set APIs with new common rss set APIs
This patch uses new common rss set APIs to replace the old APIs in PF rss
module and deletes the old rss set APIs. The related macros are also
modified.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:06 +0000 (22:20 +0800)]
net: hns3: create new set of common rss set APIs for PF and VF module
Currently, hns3 PF and VF rss module have two sets of rss set APIs to
configure rss. There is no need to keep two sets of these same APIs.
So this patch creates new set of common rss set APIs for PF and VF reuse.
These new APIs will be used to unify old APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:05 +0000 (22:20 +0800)]
net: hns3: refactor VF rss get APIs with new common rss get APIs
This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as
child member of hclgevf_dev and deletes the original child rss parameter
member(hclgevf_rss_cfg). All the rss parameter members used in VF rss
module is modified according to the new hclge_comm_rss_cfg.
Secondly VF rss get APIs are refactored to use new common rss get APIs. The
old rss get APIs in VF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:04 +0000 (22:20 +0800)]
net: hns3: refactor PF rss get APIs with new common rss get APIs
This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as
child member of hclge_dev and deletes the original child rss parameter
members in vport. All the vport child rss parameter members used in PF rss
module is modified according to the new hclge_comm_rss_cfg.
Secondly PF rss get APIs are refactored to use new common rss get APIs. The
old rss get APIs in PF are deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:03 +0000 (22:20 +0800)]
net: hns3: create new set of common rss get APIs for PF and VF rss module
The PF and VF rss get APIs are almost the same espect the suffixes of API
names. These same impementions bring double development and bugfix work.
So this patch creates new common rss get APIs for PF and VF rss module.
Subfunctions called by rss query process are also created(e.g. rss tuple
conversion APIs).
These new common rss get APIs will be used to replace PF and VF old rss
APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:02 +0000 (22:20 +0800)]
net: hns3: refactor hclge_comm_send function in PF/VF drivers
Currently, there are two different sets of special command codes in PF and
VF cmdq modules, this is because VF driver only uses small part of all the
command codes. In other words, these not used command codes in VF are also
sepcial command codes theoretically.
So this patch unifes the special command codes and deletes the bool param
is_pf of hclge_comm_send. All the related functions are refactored
according to the new hclge_comm_send function prototype.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Wed, 5 Jan 2022 14:20:01 +0000 (22:20 +0800)]
net: hns3: create new rss common structure hclge_comm_rss_cfg
Currently PF stores its rss parameters in vport structure. VF stores rss
configurations in hclgevf_rss_cfg structure. Actually hns3 rss parameters
are same beween PF and VF. The two set of rss parameters are redundent and
may add extra bugfix work.
So this patch creates new common rss parameter struct(hclge_comm_rss_cfg)
to unify PF and VF rss configurations.
These new structures will be used to unify rss configurations in PF and VF
rss APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 5 Jan 2022 11:25:14 +0000 (11:25 +0000)]
Merge branch 'lan966x-extend-switchdev-and-mdb-support'
Horatiu Vultur says:
====================
net: lan966x: Extend switchdev with mdb support
This patch series extends lan966x with mdb support by implementing
the switchdev callbacks: SWITCHDEV_OBJ_ID_PORT_MDB and
SWITCHDEV_OBJ_ID_HOST_MDB.
It adds support for both ipv4/ipv6 entries and l2 entries.
v2->v3:
- rename PGID_FIRST and PGID_LAST to PGID_GP_START and PGID_GP_END
- don't forget and relearn an entry for the CPU if there are more
references to the cpu.
v1->v2:
- rename lan966x_mac_learn_impl to __lan966x_mac_learn
- rename lan966x_mac_cpu_copy to lan966x_mac_ip_learn
- fix grammar and typos in comments and commit messages
- add reference counter for entries that copy frames to CPU
====================
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 4 Jan 2022 15:33:38 +0000 (16:33 +0100)]
net: lan966x: Extend switchdev with mdb support
Extend lan966x driver with mdb support by implementing the switchdev
calls: SWITCHDEV_OBJ_ID_PORT_MDB and SWITCHDEV_OBJ_ID_HOST_MDB.
It is allowed to add both ipv4/ipv6 entries and l2 entries. To add
ipv4/ipv6 entries is not required to use the PGID table while for l2
entries it is required. The PGID table is much smaller than MAC table
so only fewer l2 entries can be added.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 4 Jan 2022 15:33:37 +0000 (16:33 +0100)]
net: lan966x: Add PGID_GP_START and PGID_GP_END
The first entries in the PGID table are used by the front ports while
the last entries are used for different purposes like flooding mask,
copy to CPU, etc. So add these macros to define which entries can be
used for general purpose.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 4 Jan 2022 15:33:36 +0000 (16:33 +0100)]
net: lan966x: Add function lan966x_mac_ip_learn()
Extend mac functionality with the function lan966x_mac_ip_learn. This
function adds an entry in the MAC table for IP multicast addresses.
These entries can copy a frame to the CPU but also can forward on the
front ports.
This functionality is needed for mdb support. In case the CPU and some
of the front ports subscribe to an IP multicast address.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 5 Jan 2022 11:22:17 +0000 (11:22 +0000)]
Merge branch 'mtk_eth_soc-refactoring-and-clause45'
Daniel Golle says:
====================
net: ethernet: mtk_eth_soc: refactoring and Clause 45
Rework value and type of mdio read and write functions in mtk_eth_soc
and generally clean up and unify both functions.
Then add support to access Clause 45 phy registers, using newly
introduced helper inline functions added by a patch Russell King has
suggested in a reply to an earlier version of this series [1].
All three commits are tested on the Bananapi BPi-R64 board having
MediaTek MT7531BE DSA gigE switch using clause 22 MDIO and
Ubiquiti UniFi 6 LR access point having Aquantia AQR112C PHY using
clause 45 MDIO.
[1]: https://lore.kernel.org/netdev/Ycr5Cna76eg2B0An@shell.armlinux.org.uk/
v11: also address return value of mtk_mdio_busy_wait
v10: correct order of SoB lines in 2/3, change patch order in series
v9: improved formatting and Cc missing maintainer
v8: add patch from Russel King, switch to bitfield helper macros
v7: remove unneeded variables and order OR-ed call parameters
v6: further clean up functions and more cleanly separate patches
v5: fix wrong variable name in first patch covered by follow-up patch
v4: clean-up return values and types, split into two commits
v3: return -1 instead of 0xffff on error in _mtk_mdio_write
v2: use MII_DEVADDR_C45_SHIFT and MII_REGADDR_C45_MASK to extract
device id and register address. Unify read and write functions to
have identical types and parameter names where possible as we are
anyway already replacing both function bodies.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Golle [Tue, 4 Jan 2022 12:07:46 +0000 (12:07 +0000)]
net: ethernet: mtk_eth_soc: implement Clause 45 MDIO access
Implement read and write access to IEEE 802.3 Clause 45 Ethernet
phy registers while making use of new mdiobus_c45_regad and
mdiobus_c45_devad helpers.
Tested on the Ubiquiti UniFi 6 LR access point featuring
MediaTek MT7622BV WiSoC with Aquantia AQR112C.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King (Oracle) [Tue, 4 Jan 2022 12:07:00 +0000 (12:07 +0000)]
net: mdio: add helpers to extract clause 45 regad and devad fields
Add a couple of helpers and definitions to extract the clause 45 regad
and devad fields from the regnum passed into MDIO drivers.
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Golle [Tue, 4 Jan 2022 12:06:22 +0000 (12:06 +0000)]
net: ethernet: mtk_eth_soc: fix return values and refactor MDIO ops
Instead of returning -1 (-EPERM) when MDIO bus is stuck busy
while writing or 0xffff if it happens while reading, return the
appropriate -ETIMEDOUT. Also fix return type to int instead of u32.
Refactor functions to use bitfield helpers instead of having various
masking and shifting constants in the code, which also results in the
register definitions in the header file being more obviously related
to what is stated in the MediaTek's Reference Manual.
Fixes:
656e705243fd0 ("net-next: mediatek: add support for MT7623 ethernet")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Tue, 4 Jan 2022 15:02:13 +0000 (20:32 +0530)]
Revert "net: wwan: iosm: Keep device at D0 for s2idle case"
Depending on BIOS configuration IOSM driver exchanges
protocol required for putting device into D3L2 or D3L1.2.
ipc_pcie_suspend_s2idle() is implemented to put device to D3L1.2.
This patch forces PCI core know this device should stay at D0.
- pci_save_state()is expensive since it does a lot of slow PCI
config reads.
The reported issue is not observed on x86 platform. The supurios
wake on AMD platform needs to be futher debugged with orignal patch
submitter [1]. Also the impact of adding pci_save_state() needs to be
assessed by testing it on other platforms.
This reverts commit
f4dd5174e273("net: wwan: iosm: Keep device
at D0 for s2idle case").
[1] https://lore.kernel.org/all/
20211224081914.345292-2-kai.heng.feng@canonical.com/
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Link: https://lore.kernel.org/r/20220104150213.1894-1-m.chetan.kumar@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 4 Jan 2022 16:13:02 +0000 (08:13 -0800)]
Merge tag 'mac80211-next-for-net-next-2022-01-04' of git://git./linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Just a few more changes:
- mac80211: allow non-standard VHT MCSes 10/11
- mac80211: add sleepable station iterator for drivers
- nl80211: clarify a comment
- mac80211: small cleanup to use typed element helpers
* tag 'mac80211-next-for-net-next-2022-01-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next:
mac80211: use ieee80211_bss_get_elem()
nl80211: clarify comment for mesh PLINK_BLOCKED state
mac80211: Add stations iterator where the iterator function may sleep
mac80211: allow non-standard VHT MCS-10/11
====================
Link: https://lore.kernel.org/r/20220104153403.69749-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg [Mon, 20 Dec 2021 10:36:10 +0000 (11:36 +0100)]
mac80211: use ieee80211_bss_get_elem()
Instead of ieee80211_bss_get_ie(), use the more typed
ieee80211_bss_get_elem().
Link: https://lore.kernel.org/r/20211220113609.56f8e2a70152.Id5a56afb8a4f9b38d10445e5a1874e93e84b5251@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Mon, 20 Dec 2021 10:51:47 +0000 (11:51 +0100)]
nl80211: clarify comment for mesh PLINK_BLOCKED state
When a mesh link is in blocked state, it is very useful to still allow
auth requests from the peer to re-establish it.
When a remote node is power cycled, the peer state can easily end up
in blocked state if multiple auth attempts are performed. Since this
can lead to several minutes of downtime, we should accept auth attempts
of the peer after it has come back.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211220105147.88625-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Martin Blumenstingl [Tue, 28 Dec 2021 21:14:53 +0000 (22:14 +0100)]
mac80211: Add stations iterator where the iterator function may sleep
ieee80211_iterate_active_interfaces() and
ieee80211_iterate_active_interfaces_atomic() already exist, where the
former allows the iterator function to sleep. Add
ieee80211_iterate_stations() which is similar to
ieee80211_iterate_stations_atomic() but allows the iterator to sleep.
This is needed for adding SDIO support to the rtw88 driver. Some
interators there are reading or writing registers. With the SDIO ops
(sdio_readb, sdio_writeb and friends) this means that the iterator
function may sleep.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211228211501.468981-2-martin.blumenstingl@googlemail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ping-Ke Shih [Mon, 3 Jan 2022 01:36:21 +0000 (09:36 +0800)]
mac80211: allow non-standard VHT MCS-10/11
Some AP can possibly try non-standard VHT rate and mac80211 warns and drops
packets, and leads low TCP throughput.
Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
WARNING: CPU: 1 PID: 7817 at net/mac80211/rx.c:4856 ieee80211_rx_list+0x223/0x2f0 [mac8021
Since commit
c27aa56a72b8 ("cfg80211: add VHT rate entries for MCS-10 and MCS-11")
has added, mac80211 adds this support as well.
After this patch, throughput is good and iw can get the bitrate:
rx bitrate: 975.1 MBit/s VHT-MCS 10 80MHz short GI VHT-NSS 2
or
rx bitrate: 1083.3 MBit/s VHT-MCS 11 80MHz short GI VHT-NSS 2
Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1192891
Reported-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20220103013623.17052-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minghao Chi [Tue, 4 Jan 2022 11:35:43 +0000 (11:35 +0000)]
ethernet/sfc: remove redundant rc variable
Return value from efx_mcdi_rpc() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 4 Jan 2022 12:40:22 +0000 (12:40 +0000)]
Merge branch 'namespacify-mtu-ipv4'
xu xin says:
====================
ipv4: Namespaceify two sysctls related with mtu
The following patch series enables the min_pmtu and mtu_expires to
be visible and configurable per net namespace. Different namespace
application might have different requirements on the setting of
min_pmtu and mtu_expires.
If these two patches are applied, inside a net namespace we create,
we can see two more sysctls under /proc/sys/net/ipv4/route:
1. min_pmtu
2. mtu_expires
where min_pmtu and mtu_expires are configurable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
xu xin [Tue, 4 Jan 2022 10:59:47 +0000 (10:59 +0000)]
Namespaceify mtu_expires sysctl
This patch enables the sysctl mtu_expires to be configured per net
namespace.
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
xu xin [Tue, 4 Jan 2022 10:59:34 +0000 (10:59 +0000)]
Namespaceify min_pmtu sysctl
This patch enables the sysctl min_pmtu to be configured per net
namespace.
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 4 Jan 2022 03:48:27 +0000 (19:48 -0800)]
net: fixup build after bpf header changes
Recent bpf-next merge brought in header changes which uncovered
includes missing in net-next which were not present in bpf-next.
Build problems happen only on less-popular arches like hppa,
sparc, alpha etc.
I could repro the build problem with ice but not the mlx5 problem
Abdul was reporting. mlx5 does look like it should include filter.h,
anyway.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Fixes:
e63a02348958 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next")
Link: https://lore.kernel.org/all/7c03768d-d948-c935-a7ab-b1f963ac7eed@linux.vnet.ibm.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksander Jan Bajkowski [Mon, 3 Jan 2022 19:43:16 +0000 (20:43 +0100)]
net: lantiq_xrx200: add ingress SG DMA support
This patch adds support for scatter gather DMA. DMA in PMAC splits
the packet into several buffers when the MTU on the CPU port is
less than the MTU of the switch. The first buffer starts at an
offset of NET_IP_ALIGN. In subsequent buffers, dma ignores the
offset. Thanks to this patch, the user can still connect to the
device in such a situation. For normal configurations, the patch
has no effect on performance.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Radu Pirea (NXP OSS) [Mon, 3 Jan 2022 16:01:25 +0000 (18:01 +0200)]
phy: nxp-c45-tja11xx: add extts and perout support
Add support for external timestamp and periodic signal output.
TJA1103 have one periodic signal and one external time stamp signal that
can be multiplexed on all 11 gpio pins.
The periodic signal can be only enabled or disabled. Have no start time
and if is enabled will be generated with a period of one second in sync
with the LTC seconds counter. The phase change is possible only with a
half of a second.
The external timestamp signal has no interrupt and no valid bit and
that's why the timestamps are handled by polling in .do_aux_work.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 4 Jan 2022 12:12:56 +0000 (12:12 +0000)]
Merge branch 'act_tc-offload-originating-device'
Paul Blakey says:
====================
net/sched: Pass originating device to drivers offloading ct connection
Currently, drivers register to a ct zone that can be shared by multiple
devices. This can be inefficient for the driver to offload, as it
needs to handle all the cases where the tuple can come from,
instead of where it's most likely will arive from.
For example, consider the following tc rules:
tc filter add dev dev1 ... flower action ct commit zone 5 \
action mirred egress redirect dev dev2
tc filter add dev dev2 ... flower action ct zone 5 \
action goto chain chain 2
tc filter add dev dev2 ... flower ct_state +trk+est ... \
action mirred egress redirect dev dev1
Both dev2 and dev1 register to the zone 5 flow table (created
by act_ct). A tuple originating on dev1, going to dev2, will
be offloaded to both devices, and both will need to offload
both directions, resulting in 4 total rules. The traffic
will only hit originiating tuple on dev1, and reply tuple
on dev2.
By passing the originating device that created the connection
with the tuple, dev1 can choose to offload only the originating
tuple, and dev2 only the reply tuple. Resulting in a more
efficient offload.
The first patch adds an act_ct nf conntrack extension, to
temporarily store the originiating device from the skb before
offloading the connection once the connection is established.
Once sent to offload, it fills the tuple originating device.
The second patch get this information from tuples
which pass in openvswitch.
The third patch is Mellanox driver ct offload implementation using
this information to provide a hint to firmware of where this
offloaded tuple packets will arrive from (LOCAL or UPLINK port),
and thus increase insertion rate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Mon, 3 Jan 2022 11:44:52 +0000 (13:44 +0200)]
net/mlx5: CT: Set flow source hint from provided tuple device
Get originating device from tuple offload metadata match ingress_ifindex,
and set flow_source hint to either LOCAL for vf/sf reps, UPLINK for
uplink/wire/tunnel devices/bond, or ANY (as before this patch)
for all others.
This allows lower layer (software steering or firmware) to insert the tuple
rule only in one table (either rx or tx) instead of two (rx and tx).
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Mon, 3 Jan 2022 11:44:51 +0000 (13:44 +0200)]
net: openvswitch: Fill act ct extension
To give drivers the originating device information for optimized
connection tracking offload, fill in act ct extension with
ifindex from skb.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Mon, 3 Jan 2022 11:44:50 +0000 (13:44 +0200)]
net/sched: act_ct: Fill offloading tuple iifidx
Driver offloading ct tuples can use the information of which devices
received the packets that created the offloaded connections, to
more efficiently offload them only to the relevant device.
Add new act_ct nf conntrack extension, which is used to store the skb
devices before offloading the connection, and then fill in the tuple
iifindex so drivers can get the device via metadata dissector match.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 4 Jan 2022 03:52:15 +0000 (19:52 -0800)]
Merge tag 'batadv-next-pullrequest-
20220103' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- allow netlink usage in unprivileged containers, by Linus Lüssing
- remove unneeded variable, by Minghao Chi
* tag 'batadv-next-pullrequest-
20220103' of git://git.open-mesh.org/linux-merge:
batman-adv: remove unneeded variable in batadv_nc_init
batman-adv: allow netlink usage in unprivileged containers
batman-adv: Start new development cycle
====================
Link: https://lore.kernel.org/r/20220103171722.1126109-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Fainelli [Mon, 3 Jan 2022 19:40:24 +0000 (11:40 -0800)]
net: mdio: Demote probed message to debug print
On systems with large numbers of MDIO bus/muxes the message indicating
that a given MDIO bus has been successfully probed is repeated for as
many buses we have, which can eat up substantial boot time for no
reason, demote to a debug print.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Christophe JAILLET [Sun, 2 Jan 2022 21:07:05 +0000 (22:07 +0100)]
net: vxge: Use dma_set_mask_and_coherent() and simplify code
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'high_dma' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly, including a now
useless parameter to vxge_device_register().
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sun, 2 Jan 2022 20:27:39 +0000 (21:27 +0100)]
ethernet: s2io: Use dma_set_mask_and_coherent() and simplify code
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'dma_flag' can only be 'true' after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly, including the now
useless 'high_dma_flag' field in 'struct s2io_nic'.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Sun, 2 Jan 2022 22:11:26 +0000 (14:11 -0800)]
net: vertexcom: default to disabled on kbuild
Sorry for being rude but new vendors/drivers are supposed to be disabled
by default, otherwise we will have to manually keep track of all vendors
we are not interested in building.
Fixes:
2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support")
CC: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 2 Jan 2022 18:48:47 +0000 (18:48 +0000)]
Merge branch 'lynx-pcs-interface-cleanup'
Colin Foster says:
====================
lynx pcs interface cleanup
The current Felix driver (and Seville) rely directly on the lynx_pcs
device. There are other possible PCS interfaces that can be used with
this hardware, so this should be abstracted from felix. The generic
phylink_pcs is used instead.
While going through the code, there were some opportunities to change
some misleading variable names. Those are included in this patch set.
v1->v2
* compile-time fixes for freescale parts
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Foster [Wed, 29 Dec 2021 05:03:10 +0000 (21:03 -0800)]
net: pcs: lynx: use a common naming scheme for all lynx_pcs variables
pcs-lynx.c used lynx_pcs and lynx as a variable name within the same file.
This standardizes all internal variables to just "lynx"
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Foster [Wed, 29 Dec 2021 05:03:09 +0000 (21:03 -0800)]
net: ethernet: enetc: name change for clarity from pcs to mdio_device
A simple variable update from "pcs" to "mdio_device" for the mdio device
will make things a little cleaner.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Foster [Wed, 29 Dec 2021 05:03:08 +0000 (21:03 -0800)]
net: dsa: seville: name change for clarity from pcs to mdio_device
A simple variable update from "pcs" to "mdio_device" for the mdio device
will make things a little cleaner.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Foster [Wed, 29 Dec 2021 05:03:07 +0000 (21:03 -0800)]
net: dsa: felix: name change for clarity from pcs to mdio_device
Simple rename of a variable to make things more logical.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Foster [Wed, 29 Dec 2021 05:03:06 +0000 (21:03 -0800)]
net: phy: lynx: refactor Lynx PCS module to use generic phylink_pcs
Remove references to lynx_pcs structures so drivers like the Felix DSA
can reference alternate PCS drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sun, 2 Jan 2022 10:23:39 +0000 (11:23 +0100)]
enic: Remove usage of the deprecated "pci-dma-compat.h" API
In [1], Christoph Hellwig has proposed to remove the wrappers in
include/linux/pci-dma-compat.h.
Some reasons why this API should be removed have been given by Julia
Lawall in [2].
A coccinelle script has been used to perform the needed transformation
Only relevant parts are given below.
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
[1]: https://lore.kernel.org/kernel-janitors/
20200421081257.GA131897@infradead.org/
[2]: https://lore.kernel.org/kernel-janitors/alpine.DEB.2.22.394.
2007120902170.2424@hadrien/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sun, 2 Jan 2022 09:20:05 +0000 (10:20 +0100)]
qed: Use dma_set_mask_and_coherent() and simplify code
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
Now that qed_set_coherency_mask() is mostly a single call to
dma_set_mask_and_coherent(), fold it in its only caller.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sat, 1 Jan 2022 21:15:29 +0000 (22:15 +0100)]
chelsio: cxgb: Use dma_set_mask_and_coherent() and simplify code
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'pci_using_dac' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sat, 1 Jan 2022 19:04:45 +0000 (20:04 +0100)]
sun/cassini: Use dma_set_mask_and_coherent() and simplify code
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'pci_using_dac' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dust Li [Fri, 31 Dec 2021 06:08:53 +0000 (14:08 +0800)]
net/smc: add comments for smc_link_{usable|sendable}
Add comments for both smc_link_sendable() and smc_link_usable()
to help better distinguish and use them.
No function changes.
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sat, 1 Jan 2022 14:48:25 +0000 (15:48 +0100)]
tehuti: Use dma_set_mask_and_coherent() and simplify code
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask_and_coherent() with a 64-bit mask
will never fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'pci_using_dac' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sat, 1 Jan 2022 14:02:45 +0000 (15:02 +0100)]
enic: Use dma_set_mask_and_coherent()
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
This simplifies code and removes some dead code (dma_set_coherent_mask()
can not fail after a successful dma_set_mask())
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hamish MacDonald [Sat, 1 Jan 2022 12:38:25 +0000 (22:38 +1000)]
net: socket.c: style fix
Removed spaces and added a tab that was causing an error on checkpatch
Signed-off-by: Hamish MacDonald <elusivenode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Justin Iurman [Thu, 30 Dec 2021 17:10:04 +0000 (18:10 +0100)]
ipv6: ioam: Support for Queue depth data field
v3:
- Report 'backlog' (bytes) instead of 'qlen' (number of packets)
v2:
- Fix sparse warning (use rcu_dereference)
This patch adds support for the queue depth in IOAM trace data fields.
The draft [1] says the following:
The "queue depth" field is a 4-octet unsigned integer field. This
field indicates the current length of the egress interface queue of
the interface from where the packet is forwarded out. The queue
depth is expressed as the current amount of memory buffers used by
the queue (a packet could consume one or more memory buffers,
depending on its size).
An existing function (i.e., qdisc_qstats_qlen_backlog) is used to
retrieve the current queue length without reinventing the wheel.
Note: it was tested and qlen is increasing when an artificial delay is
added on the egress with tc.
[1] https://datatracker.ietf.org/doc/html/draft-ietf-ippm-ioam-data#section-5.4.2.7
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 30 Dec 2021 15:39:00 +0000 (15:39 +0000)]
net/smc: remove redundant re-assignment of pointer link
The pointer link is being re-assigned the same value that it was
initialized with in the previous declaration statement. The
re-assignment is redundant and can be removed.
Fixes:
387707fdf486 ("net/smc: convert static link ID to dynamic references")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lu [Tue, 28 Dec 2021 13:44:36 +0000 (21:44 +0800)]
net/smc: Introduce TCP ULP support
This implements TCP ULP for SMC, helps applications to replace TCP with
SMC protocol in place. And we use it to implement transparent
replacement.
This replaces original TCP sockets with SMC, reuse TCP as clcsock when
calling setsockopt with TCP_ULP option, and without any overhead.
To replace TCP sockets with SMC, there are two approaches:
- use setsockopt() syscall with TCP_ULP option, if error, it would
fallback to TCP.
- use BPF prog with types BPF_CGROUP_INET_SOCK_CREATE or others to
replace transparently. BPF hooks some points in create socket, bind
and others, users can inject their BPF logics without modifying their
applications, and choose which connections should be replaced with SMC
by calling setsockopt() in BPF prog, based on rules, such as TCP tuples,
PID, cgroup, etc...
BPF doesn't support calling setsockopt with TCP_ULP now, I will send the
patches after this accepted.
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 2 Jan 2022 12:07:39 +0000 (12:07 +0000)]
Merge branch 'smc-RDMA-net-namespace'
Tony Lu says:
====================
RDMA device net namespace support for SMC
This patch set introduces net namespace support for linkgroups.
Path 1 is the main approach to implement net ns support.
Path 2 - 4 are the additional modifications to let us know the netns.
Also, I will submit changes of smc-tools to github later.
Currently, smc doesn't support net namespace isolation. The ibdevs
registered to smc are shared for all linkgroups and connections. When
running applications in different net namespaces, such as container
environment, applications should only use the ibdevs that belongs to the
same net namespace.
This adds a new field, net, in smc linkgroup struct. During first
contact, it checks and find the linkgroup has same net namespace, if
not, it is going to create and initialized the net field with first
link's ibdev net namespace. When finding the rdma devices, it also checks
the sk net device's and ibdev's net namespaces. After net namespace
destroyed, the net device and ibdev move to root net namespace,
linkgroups won't be matched, and wait for lgr free.
If rdma net namespace exclusive mode is not enabled, it behaves as
before.
Steps to enable and test net namespaces:
1. enable RDMA device net namespace exclusive support
rdma system set netns exclusive # default is shared
2. create new net namespace, move and initialize them
ip netns add test1
rdma dev set mlx5_1 netns test1
ip link set dev eth2 netns test1
ip netns exec test1 ip link set eth2 up
ip netns exec test1 ip addr add ${HOST_IP}/26 dev eth2
3. setup server and client, connect N <-> M
ip netns exec test1 smc_run sockperf server --tcp # server
ip netns exec test1 smc_run sockperf pp --tcp -i ${SERVER_IP} # client
4. netns isolated linkgroups (2 * 2 mesh) with their own linkgroups
- server
LG-ID LG-Role LG-Type VLAN #Conns PNET-ID
00000100 SERV SINGLE 0 0
00000200 SERV SINGLE 0 0
00000300 SERV SINGLE 0 0
00000400 SERV SINGLE 0 0
- client
LG-ID LG-Role LG-Type VLAN #Conns PNET-ID
00000100 CLNT SINGLE 0 0
00000200 CLNT SINGLE 0 0
00000300 CLNT SINGLE 0 0
00000400 CLNT SINGLE 0 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lu [Tue, 28 Dec 2021 13:06:12 +0000 (21:06 +0800)]
net/smc: Add net namespace for tracepoints
This prints net namespace ID, helps us to distinguish different net
namespaces when using tracepoints.
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lu [Tue, 28 Dec 2021 13:06:11 +0000 (21:06 +0800)]
net/smc: Print net namespace in log
This adds net namespace ID to the kernel log, net_cookie is unique in
the whole system. It is useful in container environment.
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lu [Tue, 28 Dec 2021 13:06:10 +0000 (21:06 +0800)]
net/smc: Add netlink net namespace support
This adds net namespace ID to diag of linkgroup, helps us to distinguish
different namespaces, and net_cookie is unique in the whole system.
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lu [Tue, 28 Dec 2021 13:06:09 +0000 (21:06 +0800)]
net/smc: Introduce net namespace support for linkgroup
Currently, rdma device supports exclusive net namespace isolation,
however linkgroup doesn't know and support ibdev net namespace.
Applications in the containers don't want to share the nics if we
enabled rdma exclusive mode. Every net namespaces should have their own
linkgroups.
This patch introduce a new field net for linkgroup, which is standing
for the ibdev net namespace in the linkgroup. The net in linkgroup is
initialized with the net namespace of link's ibdev. It compares the net
of linkgroup and sock or ibdev before choose it, if no matched, create
new one in current net namespace. If rdma net namespace exclusive mode
is not enabled, it behaves as before.
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 31 Dec 2021 14:35:40 +0000 (14:35 +0000)]
Merge git://git./linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 31 Dec 2021 14:29:31 +0000 (14:29 +0000)]
Merge tag 'mlx5-updates-2021-12-28' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 Software steering, New features and optimizations
This patch series brings various SW steering features, optimizations and
debug-ability focused improvements.
1) Expose debugfs for dumping the SW steering resources
2) Removing unused fields
3) support for matching on new fields
4) steering optimization for RX/TX-only rules
5) Make Software steering the default steering mechanism when
available, applies only to Switchdev mode FDB
From Yevgeny Kliteynik and Muhammad Sammar:
- Patch 1 fixes an error flow in creating matchers
- Patch 2 fix lower case macro prefix "mlx5_" to "MLX5_"
- Patch 3 removes unused struct member in mlx5dr_matcher
- Patch 4 renames list field in matcher struct to list_node to reflect the
fact that is field is for list node that is stored on another struct's lists
- Patch 5 adds checking for valid Flex parser ID value
- Patch 6 adds the missing reserved fields to dr_match_param and aligns it to
the format that is defined by HW spec
- Patch 7 adds support for dumping SW steering (SMFS) resources using debugfs
in CSV format: domain and its tables, matchers and rules
- Patch 8 adds support for a new destination type - UPLINK
- Patch 9 adds WARN_ON_ONCE on refcount checks in SW steering object destructors
- Patches 10, 11, 12 add misc5 flow table match parameters and add support for
matching on tunnel headers 0 and 1
- Patch 13 adds support for matching on geneve_tlv_option_0_exist field
- Patch 14 implements performance optimization for for empty or RX/TX-only
matchers by splitting RX and TX matchers handling: matcher connection in the
matchers chain is split into two separate lists (RX only and TX only), which
solves a usecase of many RX or TX only rules that create a long chain of
RX/TX-only paths w/o the actual rules
- Patch 15 ignores modify TTL if device doesn't support it instead of
adding and unsupported action
- Patch 16 sets SMFS as a default steering mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 31 Dec 2021 14:25:47 +0000 (14:25 +0000)]
Merge branch 'hnsd3-next'
Guangbin Huang says:
====================
net: hns3: refactor cmdq functions in PF/VF
Currently, hns3 PF and VF module have two sets of cmdq APIs to provide
cmdq message interaction functions. Most of these APIs are the same. The
only differences are the function variables and names with pf and vf
suffixes. These two sets of cmdq APIs are redundent and add extra bug fix
work.
This series refactor the cmdq APIs in hns3 PF and VF by implementing one
set of common cmdq APIs for PF and VF reuse and deleting the old APIs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:43 +0000 (18:22 +0800)]
net: hns3: delete the hclge_cmd.c and hclgevf_cmd.c
currently most cmdq APIs are unified in hclge_comm_cmd.c. Newly developed
cmdq APIs should also be placed in hclge_comm_cmd.c. So there is no need to
keep hclge_cmd.c and hclgevf_cmd.c.
This patch moves the hclge(vf)_cmd_send to hclge(vf)_main.c and deletes
the source files and makefile scripts.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:42 +0000 (18:22 +0800)]
net: hns3: refactor VF cmdq init and uninit APIs with new common APIs
This patch uses common cmdq init and uninit APIs to replace the old APIs in
VF cmdq module init and uninit module. Then the old VF init and uninit
APIs is deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:41 +0000 (18:22 +0800)]
net: hns3: refactor PF cmdq init and uninit APIs with new common APIs
This patch uses common cmdq init and uninit APIs to replace the old APIs in
PF cmdq module init and uninit modules. Then the old PF init and uninit
APIs is deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:40 +0000 (18:22 +0800)]
net: hns3: create common cmdq init and uninit APIs
The PF and VF cmdq init and uninit APIs are also almost same espect the
suffixes of API names.
This patch creates common cmdq init and uninit APIs needed by PF and VF
cmdq modules. The next patch will use the new unified APIs to replace init
and uninit APIs in PF module.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:39 +0000 (18:22 +0800)]
net: hns3: refactor VF cmdq resource APIs with new common APIs
This patch uses common cmdq resource allocate/free/query APIs to replace
the old APIs in VF cmdq module and deletes the old cmdq resource APIs.
Still we kept hclgevf_cmd_setup_basic_desc name as a seam API to avoid too
many meaningless replacement.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:38 +0000 (18:22 +0800)]
net: hns3: refactor PF cmdq resource APIs with new common APIs
This patch uses common cmdq resource allocate/free/query APIs to replace
the old APIs in PF cmdq module and deletes the old cmdq resource APIs.
Still we kept hclge_cmd_setup_basic_desc name as a seam API to avoid too
many meaningless replacement.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:37 +0000 (18:22 +0800)]
net: hns3: create common cmdq resource allocate/free/query APIs
The PF and VF cmdq module resource allocate/free/query APIs are almost the
same espect the suffixes of API names. These same implementations bring
double development and bugfix work.
This patch creates common cmdq resource allocate/free/query APIs called by
PF and VF cmdq init/uninit APIs. The next patch will use the new unified
APIs to replace init/uninit APIs.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:36 +0000 (18:22 +0800)]
net: hns3: refactor hclgevf_cmd_send with new hclge_comm_cmd_send API
This patch firstly uses new hardware description struct hclge_comm_hw as
child member of hclgevf_hw and deletes the old hardware description child
members. All the hclgevf_hw variables used in VF module is modified
according to the new hclgevf_hw.
Secondly hclgevf_cmd_send is refactored to use hclge_comm_cmd_send APIs.
The old functions called by hclgevf_cmd_send are all deleted. Still we kept
hclgevf_cmd_send to avoid too many meaningless modifications.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:35 +0000 (18:22 +0800)]
net: hns3: refactor hclge_cmd_send with new hclge_comm_cmd_send API
This patch firstly uses new hardware description struct hclge_comm_hw as
child member of hclge_hw and deletes the original child memebers of
hclge_hw. All the hclge_hw variables used in PF module is modified
according to the new hclge_hw.
Secondly hclge_cmd_send is refactored to use hclge_comm_cmd_send APIs. The
old functions called by hclge_cmd_send are deleted and hclge_cmd_send is
kept to avoid too many meaningless modifications.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:34 +0000 (18:22 +0800)]
net: hns3: create new set of unified hclge_comm_cmd_send APIs
This patch create new set of unified hclge_comm_cmd_send APIs for PF and VF
cmdq module. Subfunctions called by hclge_comm_cmd_send are also created
include cmdq result check, cmdq return code conversion and ring space
opertaion APIs.
These new common cmdq APIs will be used to replace the old PF and VF cmdq
APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:33 +0000 (18:22 +0800)]
net: hns3: use struct hclge_desc to replace hclgevf_desc in VF cmdq module
This patch use new common struct hclge_desc to replace struct hclgevf_desc
in VF cmdq module and then delete the old struct hclgevf_desc.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:32 +0000 (18:22 +0800)]
net: hns3: create new cmdq hardware description structure hclge_comm_hw
Currently PF and VF cmdq APIs use struct hclge(vf)_hw to describe cmdq
hardware information needed by hclge(vf)_cmd_send. There are a little
differences between its child struct hclge_cmq_ring and hclgevf_cmq_ring.
It is redundent to use two sets of structures to support same functions.
So this patch creates new set of common cmdq hardware description
structures(hclge_comm_hw) to unify PF and VF cmdq functions. The struct
hclge_desc is still kept to avoid too many meaningless replacement.
These new structures will be used to unify hclge(vf)_hw structures in PF
and VF cmdq APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Fri, 31 Dec 2021 10:22:31 +0000 (18:22 +0800)]
net: hns3: refactor hns3 makefile to support hns3_common module
Currently we plan to refactor PF and VF cmdq module. A new file folder
hns3_common will be created to store new common APIs used by PF and VF
cmdq module. Thus the PF and VF compilation process will both depends on
the hns3_common. This may cause parallel building problems if we add a new
makefile building unit.
So this patch combined the PF and VF makefile scripts to the top level
makefile to support the new hns3_common which will be created in the next
patch.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Kliteynik [Sun, 28 Nov 2021 19:48:47 +0000 (21:48 +0200)]
net/mlx5: Set SMFS as a default steering mode if device supports it
Set SMFS (SW-managed flow steering) as a default steering mode
instead of DMFS (device-managed flow steering)
In SMFS, the driver writes the STEs (Steering Table Entries) directly
to the device's ICM, which allows for a higher rule insertion rate
than through using FW command interface, as it is done in DMFS.
SMFS/DMFS steering modes can be configured through devlink param
'flow_steering_mode'. The possible values are 'smfs' or 'dmfs'.
The desired 'flow_steering_mode' param value should be set before
enabling switchdev mode.
Example:
# devlink dev param set pci/0000:05:00.0 name flow_steering_mode smfs
# devlink dev eswitch set pci/0000:05:00.0 mode switchdev
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Yevgeny Kliteynik [Tue, 23 Nov 2021 00:11:12 +0000 (02:11 +0200)]
net/mlx5: DR, Ignore modify TTL if device doesn't support it
When modifying TTL, packet's csum has to be recalculated.
Due to HW issue in ConnectX-5, csum recalculation for modify TTL
is supported through a work-around that is specifically enabled
by configuration.
If the work-around isn't enabled, ignore the modify TTL action
rather than adding an unsupported action.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Yevgeny Kliteynik [Wed, 13 Oct 2021 23:34:00 +0000 (02:34 +0300)]
net/mlx5: DR, Improve steering for empty or RX/TX-only matchers
Every matcher has RX and TX paths. When a new matcher is created, its RX
and TX start/end anchors are connected to the respective RX and TX anchors
of the previous and next matchers.
This creates a potential performance issue: when a certain rule is added
to a matcher, in many cases it is RX or TX only rule, which may create a
long chain of RX/TX-only paths w/o the actual rules.
This patch aims to handle this issue.
RX and TX matchers are now handled separately: matcher connection in the
matchers chain is split into two separate lists: RX only and TX only.
when a new matcher is created, it is initially created 'detached' - its
RX/TX members are not inserted into the table's matcher list.
When an actual rule is added, only its appropriate RX or TX nic matchers
are then added to the table's nic matchers list and inserted into its
place in the chain of matchers.
I.e., if the rule that is being added is an RX-only rule, only the RX
part of the matcher will be connected to the chain, while TX part of the
matcher remains detached and doesn't prolong the TX chain of the matchers.
Same goes for rule deletion: when the last RX/TX rule of the nic matcher
is destroyed, the nic matcher is removed from its list.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Yevgeny Kliteynik [Mon, 8 Nov 2021 00:42:50 +0000 (02:42 +0200)]
net/mlx5: DR, Add support for matching on geneve_tlv_option_0_exist field
Match on geneve_tlv_option_0_exist field on devices that support STEv1.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Muhammad Sammar [Sun, 5 Sep 2021 14:07:49 +0000 (17:07 +0300)]
net/mlx5: DR, Support matching on tunnel headers 0 and 1
Tunnel headers are generic encapsulation headers, applies for all
tunneling protocols identified by the device native parser or by the
programmable parser, this support will enable raw matching headers 0 and 1.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Muhammad Sammar [Sun, 5 Sep 2021 11:54:59 +0000 (14:54 +0300)]
net/mlx5: DR, Add misc5 to match_param structs
Add misc5 match params to enable matching tunnel headers.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Muhammad Sammar [Sun, 5 Sep 2021 12:16:21 +0000 (15:16 +0300)]
net/mlx5: Add misc5 flow table match parameters
Add support for misc5 match parameter as per HW spec, this will allow
matching on tunnel_header fields.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Yevgeny Kliteynik [Wed, 29 Sep 2021 12:36:32 +0000 (15:36 +0300)]
net/mlx5: DR, Warn on failure to destroy objects due to refcount
Add WARN_ON_ONCE on refcount checks in SW steering object destructors
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Yevgeny Kliteynik [Sun, 24 Oct 2021 18:36:30 +0000 (21:36 +0300)]
net/mlx5: DR, Add support for UPLINK destination type
Add support for a new destination type - UPLINK.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Muhammad Sammar [Wed, 9 Dec 2020 11:40:50 +0000 (13:40 +0200)]
net/mlx5: DR, Add support for dumping steering info
Extend mlx5 debugfs support to present Software Steering resources:
dr_domain including it's tables, matchers and rules.
The interface is read-only. While dump is being presented, new steering
rules cannot be inserted/deleted.
The steering information is dumped in the CSV form with the following
format:
<object_type>,<object_ID>, <object_info>,...,<object_info>
This data can be read at the following path:
/sys/kernel/debug/mlx5/<BDF>/steering/fdb/<domain_handle>
Example:
# cat /sys/kernel/debug/mlx5/0000:82:00.0/steering/fdb/dmn_000018644
3100,0x55caa4621c50,0xee802,4,65533
3101,0x55caa4621c50,0xe0100008
Changes in V2:
- Reduce temp hex buffer size and avoid unnecessary memset
- Use bin2hex() instead of DIY loop
- Don't check debugfs functions return values
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Muhammad Sammar [Mon, 5 Jul 2021 12:37:56 +0000 (15:37 +0300)]
net/mlx5: DR, Add missing reserved fields to dr_match_param
Add the reserved fields to dr_match_param and arrange
as mlx5_ifc_dr_match_param_bits.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Yevgeny Kliteynik [Wed, 10 Nov 2021 22:22:29 +0000 (00:22 +0200)]
net/mlx5: DR, Add check for flex parser ID value
Allow only legal values for flex parser ID - values from 0 to 7.
For other values skip the parser, and as a result the matcher creation
will fail for using invalid flex parser ID.
Signed-off-by: Hamdan Igbaria <hamdani@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>