OSDN Git Service
Andrea Arcangeli [Mon, 28 Jul 2008 22:46:26 +0000 (15:46 -0700)]
mmu-notifiers: add mm_take_all_locks() operation
mm_take_all_locks holds off reclaim from an entire mm_struct. This allows
mmu notifiers to register into the mm at any time with the guarantee that
no mmu operation is in progress on the mm.
This operation locks against the VM for all pte/vma/mm related operations
that could ever happen on a certain mm. This includes vmtruncate,
try_to_unmap, and all page faults.
The caller must take the mmap_sem in write mode before calling
mm_take_all_locks(). The caller isn't allowed to release the mmap_sem
until mm_drop_all_locks() returns.
mmap_sem in write mode is required in order to block all operations that
could modify pagetables and free pages without need of altering the vma
layout (for example populate_range() with nonlinear vmas). It's also
needed in write mode to avoid new anon_vmas to be associated with existing
vmas.
A single task can't take more than one mm_take_all_locks() in a row or it
would deadlock.
mm_take_all_locks() and mm_drop_all_locks are expensive operations that
may have to take thousand of locks.
mm_take_all_locks() can fail if it's interrupted by signals.
When mmu_notifier_register returns, we must be sure that the driver is
notified if some task is in the middle of a vmtruncate for the 'mm' where
the mmu notifier was registered (mmu_notifier_invalidate_range_start/end
is run around the vmtruncation but mmu_notifier_register can run after
mmu_notifier_invalidate_range_start and before
mmu_notifier_invalidate_range_end). Same problem for rmap paths. And
we've to remove page pinning to avoid replicating the tlb_gather logic
inside KVM (and GRU doesn't work well with page pinning regardless of
needing tlb_gather), so without mm_take_all_locks when vmtruncate frees
the page, kvm would have no way to notice that it mapped into sptes a page
that is going into the freelist without a chance of any further
mmu_notifier notification.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kanoj Sarcar <kanojsarcar@yahoo.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Chris Wright <chrisw@redhat.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Izik Eidus <izike@qumranet.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrea Arcangeli [Mon, 28 Jul 2008 22:46:22 +0000 (15:46 -0700)]
mmu-notifiers: add list_del_init_rcu()
Introduce list_del_init_rcu() and document it.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Kanoj Sarcar <kanojsarcar@yahoo.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Chris Wright <chrisw@redhat.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Izik Eidus <izike@qumranet.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Mon, 28 Jul 2008 22:46:22 +0000 (15:46 -0700)]
arm: fix HAVE_CLK merge goof
This fixes a merge goof whereby ARCH_EP93XX got the "select HAVE_CLK" line
which belongs instead with ARCH_AT91.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan [Mon, 28 Jul 2008 22:46:21 +0000 (15:46 -0700)]
__ratelimit() cpu flags can't be static
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Mon, 28 Jul 2008 22:46:19 +0000 (15:46 -0700)]
tmpfs: fix kernel BUG in shmem_delete_inode
SuSE's insserve initscript ordering program hits kernel BUG at mm/shmem.c:814
on 2.6.26. It's using posix_fadvise on directories, and the shmem_readpage
method added in 2.6.23 is letting POSIX_FADV_WILLNEED allocate useless pages
to a tmpfs directory, incrementing i_blocks count but never decrementing it.
Fix this by assigning shmem_aops (pointing to readpage and writepage and
set_page_dirty) only when it's needed, on a regular file or a long symlink.
Many thanks to Kel for outstanding bugreport and steps to reproduce it.
Reported-by: Kel Modderman <kel@otaku42.de>
Tested-by: Kel Modderman <kel@otaku42.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Mon, 28 Jul 2008 22:46:18 +0000 (15:46 -0700)]
exec: include pagemap.h again to fix build
Fix compilation errors on avr32 and without CONFIG_SWAP, introduced by
ba92a43dbaee339cf5915ef766d3d3ffbaaf103c ("exec: remove some includes")
In file included from include/asm/tlb.h:24,
from fs/exec.c:55:
include/asm-generic/tlb.h: In function 'tlb_flush_mmu':
include/asm-generic/tlb.h:76: error: implicit declaration of function 'release_pages'
include/asm-generic/tlb.h: In function 'tlb_remove_page':
include/asm-generic/tlb.h:105: error: implicit declaration of function 'page_cache_release'
make[1]: *** [fs/exec.o] Error 1
This straightforward part-revert is nobody's favourite patch to address
the underlying tlb.h needs swap.h needs pagemap.h (but sparc won't like
that) mess; but appropriate to fix the build now before any overhaul.
Reported-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Reported-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Tested-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 28 Jul 2008 22:13:42 +0000 (15:13 -0700)]
Merge branch 'cpus4096-v2' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
cpu masks: optimize and clean up cpumask_of_cpu()
cpumask: export cpumask_of_cpu_map
cpumask: change cpumask_of_cpu_ptr to use new cpumask_of_cpu
cpumask: put cpumask_of_cpu_map in the initdata section
cpumask: make cpumask_of_cpu_map generic
James Bottomley [Mon, 28 Jul 2008 22:11:44 +0000 (17:11 -0500)]
ipwireless: fix compile failure
There's a brown paper bag compile failure introduced by this patch
commit
a01386924874c4d6d67f8a34e66f04452c2abb69
Author: David Sterba <dsterba@suse.cz>
Date: Mon Jul 28 16:53:32 2008 +0200
ipwireless: Preallocate received packet buffers with MRU size
Really, it can't ever have been even compile tested. It looks like the
closing bracket is in the wrong place, so this is the fix.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Molnar [Mon, 28 Jul 2008 21:32:00 +0000 (23:32 +0200)]
Merge branch 'linus' into cpus4096
Conflicts:
kernel/stop_machine.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Mon, 28 Jul 2008 18:32:33 +0000 (11:32 -0700)]
cpu masks: optimize and clean up cpumask_of_cpu()
Clean up and optimize cpumask_of_cpu(), by sharing all the zero words.
Instead of stupidly generating all possible i=0...NR_CPUS 2^i patterns
creating a huge array of constant bitmasks, realize that the zero words
can be shared.
In other words, on a 64-bit architecture, we only ever need 64 of these
arrays - with a different bit set in one single world (with enough zero
words around it so that we can create any bitmask by just offsetting in
that big array). And then we just put enough zeroes around it that we
can point every single cpumask to be one of those things.
So when we have 4k CPU's, instead of having 4k arrays (of 4k bits each,
with one bit set in each array - 2MB memory total), we have exactly 64
arrays instead, each 8k bits in size (64kB total).
And then we just point cpumask(n) to the right position (which we can
calculate dynamically). Once we have the right arrays, getting
"cpumask(n)" ends up being:
static inline const cpumask_t *get_cpu_mask(unsigned int cpu)
{
const unsigned long *p = cpu_bit_bitmap[1 + cpu % BITS_PER_LONG];
p -= cpu / BITS_PER_LONG;
return (const cpumask_t *)p;
}
This brings other advantages and simplifications as well:
- we are not wasting memory that is just filled with a single bit in
various different places
- we don't need all those games to re-create the arrays in some dense
format, because they're already going to be dense enough.
if we compile a kernel for up to 4k CPU's, "wasting" that 64kB of memory
is a non-issue (especially since by doing this "overlapping" trick we
probably get better cache behaviour anyway).
[ mingo@elte.hu:
Converted Linus's mails into a commit. See:
http://lkml.org/lkml/2008/7/27/156
http://lkml.org/lkml/2008/7/28/320
Also applied a family filter - which also has the side-effect of leaving
out the bits where Linus calls me an idio... Oh, never mind ;-)
]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Mon, 28 Jul 2008 19:14:43 +0000 (21:14 +0200)]
Merge branch 'linus' into cpus4096
Linus Torvalds [Mon, 28 Jul 2008 16:59:26 +0000 (09:59 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: add driver for Atmel integrated touchscreen controller
Input: ads7846 - optimize order of calculating Rt in ads7846_rx()
Input: ads7846 - fix sparse endian warnings
Input: uinput - remove duplicate include
Input: serio - offload resume to kseriod
Input: serio - mark serio_register_driver() __must_check
Linus Torvalds [Mon, 28 Jul 2008 16:46:00 +0000 (09:46 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: fix uninitialized variable for search_rsb_list callers
dlm: release socket on error
dlm: fix basts for granted CW waiting PR/CW
dlm: check for null in device_write
Linus Torvalds [Mon, 28 Jul 2008 16:05:35 +0000 (09:05 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc: Disable 64K hugetlb support when doing 64K SPU mappings
powerpc/powermac: Fixup default serial port device for pmac_zilog
powerpc/powermac: Use sane default baudrate for SCC debugging
powerpc/mm: Implement _PAGE_SPECIAL & pte_special() for 64-bit
powerpc: Show processor cache information in sysfs
powerpc: Make core id information available to userspace
powerpc: Make core sibling information available to userspace
powerpc/vio: More fallout from dma_mapping_error API change
ibmveth: Fix multiple errors with dma_mapping_error conversion
powerpc/pseries: Fix CMO sysdev attribute API change fallout
powerpc: Enable tracehook for the architecture
powerpc: Add TIF_NOTIFY_RESUME support for tracehook
powerpc: Add asm/syscall.h with the tracehook entry points
powerpc: Make syscall tracing use tracehook.h helpers
powerpc: Call tracehook_signal_handler() when setting up signal frames
powerpc: Update cpu_sibling_maps dynamically
powerpc: register_cpu_online should be __cpuinit
powerpc: kill useless SMT code in prom_hold_cpus
powerpc: Fix 8xx build failure
powerpc: Fix vio build warnings
...
Linus Torvalds [Mon, 28 Jul 2008 15:41:56 +0000 (08:41 -0700)]
Merge git://git./linux/kernel/git/kkeil/ISDN-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6:
Remove deprecated virt_to_bus()
Linus Torvalds [Mon, 28 Jul 2008 15:41:13 +0000 (08:41 -0700)]
Merge git://git./linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (72 commits)
sh: SuperH Mobile CEU and camera platform data for AP325RXA
sh: Update smc911x platform data for AP325RXA
sh: SuperH Mobile LCDC platform data for AP325RXA
sh: Add SuperH Mobile CEU platform data for Migo-R
sh: Add SuperH Mobile LCDC platform data for Migo-R
sh: Move asid_cache() out of ifdef to fix SH-3/4 nommu build.
sh: Workaround for __put_user_asm() bug with gcc 4.x on big-endian.
sh: Wire up new syscalls.
sh: fix uImage Entry Point
sh_keysc: remove request_mem_region() and release_mem_region()
sh: Don't miss pending signals returning to user mode after signal processing
sh: Use clk_always_enable() on sh7366
sh: Use clk_always_enable() on sh7343 / SE77343
sh: Use clk_always_enable() on sh7722 / Migo-R / SE7722
sh: Use clk_always_enable() on sh7723 / ap325rxa
sh: Introduce clk_always_enable() function
sh: Show all clocks and their state in /proc/clocks
sh: Merge sh7343 and sh7722 clock code
sh: Add SuperH Mobile MSTPCR bits to clock framework
sh: Use arch_flags to simplify sh7722 siu clock code
...
Linus Torvalds [Mon, 28 Jul 2008 15:37:46 +0000 (08:37 -0700)]
Merge git://git./linux/kernel/git/rusty/linux-2.6-for-linus
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
stop_machine: fix up ftrace.c
stop_machine: Wean existing callers off stop_machine_run()
stop_machine(): stop_machine_run() changed to use cpu mask
Hotplug CPU: don't check cpu_online after take_cpu_down
Simplify stop_machine
stop_machine: add ALL_CPUS option
module: fix build warning with !CONFIG_KALLSYMS
Linus Torvalds [Mon, 28 Jul 2008 15:35:40 +0000 (08:35 -0700)]
Merge git://git./linux/kernel/git/mchehab/v4l-dvb
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (98 commits)
V4L/DVB (8549): mxl5007: Fix an error at include file
V4L/DVB (8548): pwc: Fix compilation
V4L/DVB (8546): add tuner-3036 and dpc7146 drivers to feature-removal-schedule.txt
V4L/DVB (8546): saa7146: fix read from uninitialized memory
V4L/DVB (8544): gspca: probe/open race.
V4L/DVB (8543): em28xx: Rename #define for Compro VideoMate ForYou/Stereo
V4L/DVB (8542): em28xx: AMD ATI TV Wonder HD 600 entry at cards struct is duplicated
V4L/DVB (8541): em28xx: HVR-950 entry is duplicated.
V4L/DVB (8540): em28xx-cards: Add Compro VideoMate ForYou/Stereo model
V4L/DVB (8539): em28xx-cards: New supported IDs for analog models
V4L/DVB (8538): em28xx-cards: Add GrabBeeX+ USB2800 model
V4L/DVB (8534): remove select's of FW_LOADER
V4L/DVB (8522): videodev2: Fix merge conflict
V4L/DVB (8532): mxl5007t: remove excessive locks
V4L/DVB (8531): mxl5007t: move i2c gate handling outside of mutex protected code blocks
V4L/DVB (8530): au0828: add support for new revision of HVR950Q
V4L/DVB (8529): mxl5007t: enable _init and _sleep power management functionality
V4L/DVB (8528): add support for MaxLinear MxL5007T silicon tuner
V4L/DVB (8526): saa7146: fix VIDIOC_ENUM_FMT
V4L/DVB (8525): fix a few assorted spelling mistakes.
...
Linus Torvalds [Mon, 28 Jul 2008 15:33:25 +0000 (08:33 -0700)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Set CONFIG_HAVE_ARCH_TRACEHOOK
sparc: Add task_pt_regs().
sparc: Add call to tracehook_signal_handler().
sparc: Create and use TIF_NOTIFY_RESUME.
sparc: Use tracehook routines in syscall_trace().
sparc64: tracehook: CONFIG_HAVE_ARCH_TRACEHOOK
sparc: Add user_stack_pointer().
sparc64: tracehook_signal_handler
sparc64: tracehook: TIF_NOTIFY_RESUME
sparc: Add asm/syscall.h
sparc64: tracehook syscall
sparc: enable headers_export again
sparc, sparc64: use arch/sparc/include
Linus Torvalds [Mon, 28 Jul 2008 15:32:25 +0000 (08:32 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: missing bits of net-namespace / sysctl
ipcomp: Fix warnings after ipcomp consolidation.
dccp: Add check for truncated ICMPv6 DCCP error packets
dccp: Fix incorrect length check for ICMPv4 packets
dccp: Add check for sequence number in ICMPv6 message
dccp: Fix sequence number check for ICMPv4 packets
dccp: Bug-Fix - AWL was never updated
dccp: Allow to distinguish original and retransmitted packets
Randy Dunlap [Mon, 28 Jul 2008 03:44:24 +0000 (20:44 -0700)]
SubmittingPatches: add git pull & diffstat format info
Add git pull command info and diffstat summary info so that we don't
have to search email archives for it repeatedly.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Rothwell [Mon, 28 Jul 2008 01:05:04 +0000 (11:05 +1000)]
more sysdev API change fallout - drivers/base/memory.c
Noticed because of this warning:
drivers/base/memory.c:279: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Sun, 27 Jul 2008 21:47:12 +0000 (23:47 +0200)]
ACPI/CPUIDLE: prevent setting pm_idle to NULL
pm_idle_save resp. pm_idle_old can be NULL when the restore code in
acpi_processor_cst_has_changed() resp. cpuidle_uninstall_idle_handler()
is called. This can set pm_idle unconditinally to NULL, which causes the
kernel to panic when calling pm_idle in the x86 idle code. This was
covered by an extra check for !pm_idle in the x86 idle code, which was
removed during the x86 idle code refactoring.
Instead of restoring the pm_idle check in the x86 code prevent the
acpi/cpuidle code to set pm_idle to NULL.
Reported by: Dhaval Giani http://lkml.org/lkml/2008/7/2/309
Based on a debug patch from Ingo Molnar
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 28 Jul 2008 15:28:50 +0000 (08:28 -0700)]
Merge branch 'i2c-for-linus' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'i2c-for-linus' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c: Blackfin I2C Driver: Functional power management support
i2c: Documentation: upgrading clients HOWTO
i2c: S3C24XX I2C frequency scaling support.
i2c: i2c_gpio: keep probe resident for hotplugged devices.
i2c: S3C2410: Pass the I2C bus number via drivers platform data
David Sterba [Mon, 28 Jul 2008 14:53:32 +0000 (16:53 +0200)]
ipwireless: Preallocate received packet buffers with MRU size
ipwireless: Preallocate received packet buffers with MRU size
Packets are assembled from link size (~300 bytes) up to PPP MRU
(1500 by default). Try to preallocate full size rather than
repeatedly advance buffer size by 256 bytes.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:53:27 +0000 (16:53 +0200)]
ipwireless: Put packets to pool start
ipwireless: Put packets to pool start
Put packets to pool start, try to reuse cached memory.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:53:21 +0000 (16:53 +0200)]
ipwireless: Increase PPP outgoing queue size
ipwireless: Increase PPP outgoing queue size
Increase default size of PPP outgoing queue. Currently set to 1, which
means that a packet quickly following another pushed by PPP must wait
until hardware actually sends the previous and PPP has to be waken up
by ppp_wakeup(). This slows down upstream.
Now PPP can push more packets at once which get buffered inside driver
and pushed immediatelly to hardware when previous packet is out.
Experiments show that size = 10 is quite good for all connection types
(GPRS/EDGE/UMTS) and gains 4 KB/sec of upload for UMTS for batch uploads.
Need for higher queue size than 10 occures in only < 0.1 % of cases.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:53:16 +0000 (16:53 +0200)]
ipwireless: Explicitly request io and mem regions
ipwireless: Explicitly request io and mem regions
Documentation/pcmcia/driver-changes.txt says, that driver should call request_region
for used memory/io regions since PCMCIA does not do this (since 2.6.8).
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:53:11 +0000 (16:53 +0200)]
ipwireless: Constify buffer variables
ipwireless: Constify buffer variables
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:53:05 +0000 (16:53 +0200)]
ipwireless: Do not return value from sending funcs
ipwireless: Do not return value from sending funcs
Do not return value from do_send_fragment and do_send_packet, it's not used.
The packet size checks are not useful too:
* zero length packet will never be sent, caller always passes packet_header
size which is either 1 or 3
* MTU check is done in caller, no need to repeat
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:53:00 +0000 (16:53 +0200)]
ipwireless: Remove endian-dependent bitfields
ipwireless: Remove endian-dependent bitfields
Remove endian-dependent bitfields and use bitmasks to transform
packet header bitfields from/to machine order.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:52:55 +0000 (16:52 +0200)]
ipwireless: Glue splitted printk strings back
ipwireless: Glue splitted printk strings back
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:52:49 +0000 (16:52 +0200)]
ipwireless: Remove pt_regs from interrupt handler
ipwireless: Remove pt_regs from interrupt handler
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:52:44 +0000 (16:52 +0200)]
ipwireless: Rename spinlock variables to lock
ipwireless: Rename spinlock variables to lock
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:52:39 +0000 (16:52 +0200)]
ipwireless: Remove unused defines
ipwireless: Remove unused defines
Remove unused defines, defines hiding variables, defines hiding 0.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Sterba [Mon, 28 Jul 2008 14:52:33 +0000 (16:52 +0200)]
ipwireless: Misc cleanups
ipwireless: Misc cleanups
- remove likely() and some extra () in ifs
- use unsigned in for loops
- remove useless typecasts
- remove obvious comments
- add () around ?:
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Hennerich [Sun, 27 Jul 2008 06:41:54 +0000 (14:41 +0800)]
i2c: Blackfin I2C Driver: Functional power management support
PM_SUSPEND_MEM: Blackfin does not maintain register state through
Hibernate. Save and restore peripheral base initialization during
PM transitions.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks [Mon, 28 Jul 2008 11:04:08 +0000 (12:04 +0100)]
i2c: Documentation: upgrading clients HOWTO
Add a document describing how i2c clients on Linux 2.6 can be
moved from the old to the new driver model.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks [Mon, 28 Jul 2008 11:04:07 +0000 (12:04 +0100)]
i2c: S3C24XX I2C frequency scaling support.
Add support for CPU frequency scaling to the S3C24XX I2C driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks [Mon, 28 Jul 2008 11:04:09 +0000 (12:04 +0100)]
i2c: i2c_gpio: keep probe resident for hotplugged devices.
Change the i2c_gpio driver to use platform_driver_register()
instead of platform_driver_probe() to ensure that is can
attach to any devices that may be loaded after it has initialised.
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks [Mon, 28 Jul 2008 11:04:06 +0000 (12:04 +0100)]
i2c: S3C2410: Pass the I2C bus number via drivers platform data
Allow the platform data to specify the bus bumber that the
new I2C bus will be given. This is to allow the use of the
board registration mechanism to specify the new style of
I2C device registration which allows boards to provide a
list of attached devices.
Note, as discussed on the mailing list, we have dropped
backwards compatibility of adding an dynamic bus number
as it should not affect most boards to have the bus pinned
to 0 if they have either not specified platform data for
driver. Any board supplying platform data will automatically
have the bus_num field set to 0, and anyone who needs the
driver on a different bus number can supply platform data
to set bus_num.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Karsten Keil [Mon, 28 Jul 2008 10:21:25 +0000 (12:21 +0200)]
Remove deprecated virt_to_bus()
Please pull from git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6.git master
This was a forgotten item in a printk from the old driver,
the DMA allocation use already the new interface.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Magnus Damm [Mon, 28 Jul 2008 10:14:35 +0000 (19:14 +0900)]
sh: SuperH Mobile CEU and camera platform data for AP325RXA
Add AP325RXA specific platform data for on-chip sh7723 CEU and ncm03j camera.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Mon, 28 Jul 2008 10:11:07 +0000 (19:11 +0900)]
sh: Update smc911x platform data for AP325RXA
Pass board specific smc911x parameters using struct smc911x_platdata.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Mon, 28 Jul 2008 10:07:04 +0000 (19:07 +0900)]
sh: SuperH Mobile LCDC platform data for AP325RXA
Add LCD panel platform data for the AP325RXA board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Mon, 28 Jul 2008 09:51:01 +0000 (18:51 +0900)]
sh: Add SuperH Mobile CEU platform data for Migo-R
Add Migo-R specific platform data for on-chip sh7722 CEU and ov772x camera.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Mon, 28 Jul 2008 09:47:30 +0000 (18:47 +0900)]
sh: Add SuperH Mobile LCDC platform data for Migo-R
Add WVGA and QVGA LCD panel support to Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Mon, 28 Jul 2008 09:39:25 +0000 (18:39 +0900)]
sh: Move asid_cache() out of ifdef to fix SH-3/4 nommu build.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshinori Sato [Mon, 28 Jul 2008 09:36:13 +0000 (18:36 +0900)]
sh: Workaround for __put_user_asm() bug with gcc 4.x on big-endian.
I think this problem is GCC(4.1.2) bug.
Syscall "getdents" returned "dirent->d_off" is always 0.
I think other EB enviroment have same problem.
Problem code
0c03c954 <filldir>:
:
c03c97a: 58 f7 mov.l @(28,r15),r8 !-> offset (high)
c03c97c: 59 f8 mov.l @(32,r15),r9 !-> offset (low)
c03c97e: 53 f9 mov.l @(36,r15),r3
c03c980: 54 fa mov.l @(40,r15),r4
:
c03c9a0: 21 82 mov.l r8,@r1 !offset(high) -> dirent->d_off
It's workaround patch.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Mon, 28 Jul 2008 09:34:45 +0000 (18:34 +0900)]
sh: Wire up new syscalls.
This wires up the signalfd4, eventfd2, epoll_create1, dup3, pipe2, and
inotify_init1 syscalls.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshihiro Shimoda [Wed, 23 Jul 2008 07:49:06 +0000 (16:49 +0900)]
sh: fix uImage Entry Point
fix the problem that cannot boot using uImage when PAGE_SIZE is
8kbyte or 64kbyte.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Tetsuya Mukawa [Fri, 18 Jul 2008 22:46:53 +0000 (07:46 +0900)]
sh_keysc: remove request_mem_region() and release_mem_region()
Remove request_mem_region() and release_mem_region() from sh_keysc driver.
Those functions can find resource conflict, but it is already checked in
platform_device_add().
Signed-off-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Stuart MENEFY [Thu, 17 Jul 2008 12:08:40 +0000 (13:08 +0100)]
sh: Don't miss pending signals returning to user mode after signal processing
Without this patch, signals sent during architecture specific signal
handling (typically as a result of the user's stack being inaccessible)
are ignored.
This is the SH version of commit
c3ff8ec31c1249d268cd11390649768a12bec1b9
which was for the i386.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 10:20:11 +0000 (19:20 +0900)]
sh: Use clk_always_enable() on sh7366
Use clk_always_enable() in the sh7366 processor code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 10:18:24 +0000 (19:18 +0900)]
sh: Use clk_always_enable() on sh7343 / SE77343
Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 10:16:11 +0000 (19:16 +0900)]
sh: Use clk_always_enable() on sh7722 / Migo-R / SE7722
Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 10:13:34 +0000 (19:13 +0900)]
sh: Use clk_always_enable() on sh7723 / ap325rxa
Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 10:09:51 +0000 (19:09 +0900)]
sh: Introduce clk_always_enable() function
Add SuperH specific funcion clk_always_enable(), useful to enable MSTPCR
bits in processor or board specific code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 10:05:54 +0000 (19:05 +0900)]
sh: Show all clocks and their state in /proc/clocks
Show all clocks in /proc/clocks, and also show if they are enabled or
disabled. This is useful to show MSTPCR bits on SuperH Mobile processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 10:02:23 +0000 (19:02 +0900)]
sh: Merge sh7343 and sh7722 clock code
This code makes sh7343 share the sh7722 clock code. Instead of just using
the good and very old sh7343 clock implmentation, switch to the new MSTPCR
enabled clock code. SIU clocks are disabled on sh7343 for now.
With this change all SuperH Mobile devices now use the same clock code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 09:56:15 +0000 (18:56 +0900)]
sh: Add SuperH Mobile MSTPCR bits to clock framework
Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 09:52:19 +0000 (18:52 +0900)]
sh: Use arch_flags to simplify sh7722 siu clock code
Make use of arch_flags to simplify the SIU clock code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 17 Jul 2008 09:48:57 +0000 (18:48 +0900)]
sh: Add arch_flags to struct clk
Add arch_flags to struct clk so we can keep per-clock private data
somewhere and share code between multiple clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adrian Bunk [Wed, 16 Jul 2008 16:45:40 +0000 (19:45 +0300)]
fix sh ptep_get_and_clear breakage
Commit
1ea0704e0da65b2b46f9142ff1391163aac24060
(mm: add a ptep_modify_prot transaction abstraction)
triggered on sh build errors like the following:
<-- snip -->
...
CC arch/sh/mm/pg-sh4.o
cc1: warnings being treated as errors
include2/asm/pgtable.h:139: error: 'ptep_get_and_clear' declared inline after being called
include2/asm/pgtable.h:139: error: previous declaration of 'ptep_get_and_clear' was here
make[2]: *** [arch/sh/mm/pg-sh4.o] Error 1
<-- snip -->
Since there's no good reason for marking these global functions as
"inline" this patch therefore removes the inline's.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshihiro Shimoda [Wed, 16 Jul 2008 11:21:09 +0000 (20:21 +0900)]
sh: Renesas R0P7785LC0011RL board support
This adds initial support for the Renesas R0P7785LC0011RL board.
This patch supports 29bit address mode only.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 16 Jul 2008 10:02:54 +0000 (19:02 +0900)]
sh: Add memory chunks to SH-Mobile UIO devices
This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 15 Jul 2008 12:55:03 +0000 (21:55 +0900)]
sh: Export sh7366 VPU, VEU(1), VEU(2) using uio_pdrv_genirq
This patch exports the VPU, VEU(1) and VEU(2) blocks of the sh7366
to user space using the uio_pdrv_genirq platform driver.
While at it, fix up the VEU(2) interrupt vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 15 Jul 2008 12:53:33 +0000 (21:53 +0900)]
sh: Export sh7723 VPU, VEU2H0, VEU2H1 using uio_pdrv_genirq
This patch exports the VPU, VEU2H0 and VEU2H1 blocks of the sh7723
to user space using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 15 Jul 2008 12:52:19 +0000 (21:52 +0900)]
sh: Export sh7722 VPU and VEU using uio_pdrv_genirq
This patch exports the VPU and VEU blocks of the sh7722 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 15 Jul 2008 12:51:39 +0000 (21:51 +0900)]
sh: Export sh7343 VPU and VEU using uio_pdrv_genirq
This patch exports the VPU and VEU blocks of the sh7343 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshinori Sato [Wed, 9 Jul 2008 16:20:03 +0000 (01:20 +0900)]
sh2(A) exception handler update
This patch is
By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize
By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshihiro Shimoda [Mon, 7 Jul 2008 12:11:54 +0000 (21:11 +0900)]
sh: update Solution Engine 7343
updated the following codes for Solution Endine 7343:
- fix compile error in arch/sh/boards/se/7343/irq.c
- add nor flash physmaps
- update defconfig
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshihiro Shimoda [Mon, 7 Jul 2008 12:11:51 +0000 (21:11 +0900)]
sh: update sh7343 code
updated the following codes for SH7343:
- add register_intc_controller()
- add EARLY_SCIF_CONSOLE_PORT
- add define of CPG register
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Sat, 5 Jul 2008 03:33:30 +0000 (12:33 +0900)]
sh: fix pg-sh4.c build breakage in linux-next
Remove inline from ptep_get_and_clean() to match with header file prototype.
Makes linux-next build.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Sat, 5 Jul 2008 03:32:44 +0000 (12:32 +0900)]
sh: enable I2C on the ap325rxa board
This patch enables I2C on the sh7723-based ap325rxa board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Sat, 5 Jul 2008 03:32:23 +0000 (12:32 +0900)]
sh: add SuperH Mobile I2C platform data to sh7366
This patch adds platform data for the single I2C channel on sh7366.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Sat, 5 Jul 2008 03:32:06 +0000 (12:32 +0900)]
sh: add SuperH Mobile I2C platform data to sh7723
This patch adds platform data for the single I2C channel on sh7723.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Sat, 5 Jul 2008 03:31:46 +0000 (12:31 +0900)]
sh: add SuperH Mobile I2C platform data to sh7343
This patch adds platform data for two I2C channels to the sh7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshihiro Shimoda [Fri, 4 Jul 2008 03:37:12 +0000 (12:37 +0900)]
sh: add interrupt ack code to sh4a
This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshinori Sato [Fri, 4 Jul 2008 03:54:51 +0000 (12:54 +0900)]
sh: Fix up link error on SH-2 zImage with older binutils.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Stuart Menefy [Wed, 2 Jul 2008 08:51:23 +0000 (17:51 +0900)]
sh: Conditionally re-enable IRQs in fault path.
The current kernel behaviour is to reenable interrupts unconditionally
when taking a page fault. This patch changes this to only enable them
if interrupts were previously enabled.
It also fixes a problem seen with this fix in place: the kernel previously
flushed the vsyscall page when handling a signal, which is not only
unncessary, but caused a possible sleep with interrupts disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Wed, 2 Jul 2008 08:46:40 +0000 (17:46 +0900)]
sh: Record the major cut revision for probed SH-4A parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Chris Smith [Wed, 2 Jul 2008 06:17:11 +0000 (15:17 +0900)]
sh: Optimized flush_icache_range() implementation.
Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Stuart Menefy [Wed, 2 Jul 2008 06:15:09 +0000 (15:15 +0900)]
sh: Stub in silicon cut in CPU info.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Wed, 2 Jul 2008 04:58:38 +0000 (13:58 +0900)]
sh: Tidy up the SH-3 exception vector table.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshinori Sato [Wed, 2 Jul 2008 02:20:24 +0000 (22:20 -0400)]
SH7619 add ethernet controler support
- Add EtherC + PHY resource define.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu [Tue, 24 Jun 2008 04:00:52 +0000 (13:00 +0900)]
sh: Remove sh_pcic_io_xxx function from Solution Engine IO code
sh_pcic_io_xxx function are very old.
In linux-2.4, mrshpc_ss socket driver used this function.
But there is not this driver to the present kernel.
I deleted these cords and checked operation.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu [Thu, 19 Jun 2008 10:27:55 +0000 (19:27 +0900)]
sh: Fix Kconfig of AP-325RXA
The CPU of AP-325RXA is SH7723, but a CPU becomes selectable.
This patch fixes this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu [Wed, 18 Jun 2008 09:32:03 +0000 (18:32 +0900)]
sh: Clean up code of Solution Engine 770x
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu [Wed, 18 Jun 2008 09:31:46 +0000 (18:31 +0900)]
sh: Update Solution Enginge 7712 defconfig
Enable SH-Ether support and NFS userland support.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu [Wed, 18 Jun 2008 09:29:06 +0000 (18:29 +0900)]
sh: Solution Enginge 7710/7712 SH-Ether support
Add support SH-Ether for Hitachi Solution Engine.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adrian Bunk [Wed, 18 Jun 2008 00:36:50 +0000 (03:36 +0300)]
sh/kernel/ cleanups
This patch contains the following cleanups:
- make the following needlessly global code static:
- cf-enabler.c: cf_init()
- cpu/clock.c: __clk_enable()
- cpu/clock.c: __clk_disable()
- process_32.c: default_idle()
- time_32.c: struct clocksource_sh
- timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
- process_{32,64}.c: disable_hlt()
- process_{32,64}.c: enable_hlt()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adrian Bunk [Tue, 17 Jun 2008 22:33:40 +0000 (01:33 +0300)]
sh: make pcibios_max_latency static
This patch makes the needlessly global pcibios_max_latency static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adrian Bunk [Tue, 17 Jun 2008 22:31:03 +0000 (01:31 +0300)]
sh: make EARLY_PCI_OP's static
This patch makes the needlessly global EARLY_PCI_OP's static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adrian Bunk [Tue, 17 Jun 2008 22:30:57 +0000 (01:30 +0300)]
sh/boards/dreamcast/rtc.c: make 2 functions static
This patch makes the needlessly global aica_rtc_{get,set}timeofday()
static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adrian McMenamin [Sun, 15 Jun 2008 19:48:09 +0000 (20:48 +0100)]
maple: tidy maple_driver code by removing redundant connect/disconnect
The connect and disconnect functions are unnecessary - everything they do can be
accomplished in the initial probe - so remove them.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu [Fri, 6 Jun 2008 08:04:56 +0000 (17:04 +0900)]
sh: Renesas Solutions SH7763RDP board support
This patch adds basic support for the SH7763RDP board.
This supports a basic stuff provided in SH7763, like SCIF,
NOR Flash and USB host.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu [Fri, 6 Jun 2008 08:04:08 +0000 (17:04 +0900)]
sh: Add SCIF2 support for SH7763.
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yusuke Goda [Fri, 6 Jun 2008 08:03:23 +0000 (17:03 +0900)]
sh: Add support Renesas Solutions AP-325RXA board
This board is SH7723 base board.
This has SCIF, LCDC, USB Host controler, NOR/NAND Flash, Sound,
Ether and other.
This patch supports SCIF, NOR Flash.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 3 Jun 2008 11:05:39 +0000 (20:05 +0900)]
sh: Initial consolidation of the _32/_64 uaccess split.
This consolidates everything but the bare assembly routines, which we
will sync up in a follow-up patch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>