OSDN Git Service
Chaitra P B [Tue, 24 Apr 2018 09:28:37 +0000 (05:28 -0400)]
scsi: mpt3sas: Allow processing of events during driver unload.
Events were not processed during driver unload, hence unloading of
driver doesn't complete when drives are disconnected while unloading of
driver. So don't block events in ISR path, i,e., remove the flag
ioc->remove_host so that events are getting processed during driver
unload. Thus allowing driver unload to complete by processing drive
removal events during driver unload.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Tue, 24 Apr 2018 09:28:36 +0000 (05:28 -0400)]
scsi: mpt3sas: Increase event log buffer to support 24 port HBA's.
For 24 port HBA's events generated by IOC are more in certain cases and
the current circular buffer may be overwritten.Hence increased the event
log buffer to accommodate more events.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Tue, 24 Apr 2018 09:28:35 +0000 (05:28 -0400)]
scsi: mpt3sas: Added support for SAS Device Discovery Error Event.
The SAS Device Discovery Error Event is sent to the host when discovery
for a particular device is failed during discovery, even after maximum
retries by the IOC.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Tue, 24 Apr 2018 09:28:34 +0000 (05:28 -0400)]
scsi: mpt3sas: Enhanced handling of Sense Buffer.
Enhanced DMA allocation for Sense Buffer, if the allocation does not fit
within same 4GB.Introduced is_MSB_are_same function to check if allocted
buffer within 4GB range or not.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Tue, 24 Apr 2018 09:28:33 +0000 (05:28 -0400)]
scsi: mpt3sas: Optimize I/O memory consumption in driver.
For every IO, memory of PAGE size is allocated for handling NVMe native
PRPS. And in addition to that for every IO (chains need per IO * chain
buffer size, e.g. 38 * 128byte) amount of memory is allocated for chain
buffers.
However, at any point of time; the IO request can be for NVMe target
device (where PRP's page is used for framing PRP's) or can be for SCSI
target device (where chain buffers are used for framing chain
SGE's). This patch modifies the driver to reuse same pre-allocated PRP
page buffers as a chain buffer for IO's targeted for SCSI target
devices. No need to allocate separate buffers for chain SGE's buffers.
Suppose if the number of chain buffers need for IO doesn't fit in the
PRP Page size then driver maintain's separate buffers for those extra
chain buffers that exceeds the PRP page size. For example consider PRP
page size as 4K and chain buffer size as 128 bytes, then number of chain
buffers that can fit in PRP page is 4096/128 => 32. if the number of
chain buffer need per IO exceeds 32; for example consider number of
chains need per IO is 36 then for remaining 4 chain buffer's driver
allocates them individual.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Tue, 24 Apr 2018 09:28:32 +0000 (05:28 -0400)]
scsi: mpt3sas: Lockless access for chain buffers.
Introduces Chain lookup table/tracker and implements accessing chain
buffer using smid. Removed link list based access of chain buffer which
requires lock and allocated as many chains needed.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Tue, 24 Apr 2018 09:28:31 +0000 (05:28 -0400)]
scsi: mpt3sas: Pre-allocate RDPQ Array at driver boot time.
Instead of allocating RDPQ array (This stores the address's of each RDPQ
pools) at run time, now it will be allocated once during driver load
time and same will be reused during host reset operation also (instead
of allocating & freeing this buffer on the fly during every host reset
operation) and then freed during driver unload.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chaitra P B [Tue, 24 Apr 2018 09:28:30 +0000 (05:28 -0400)]
scsi: mpt3sas: Bug fix for big endian systems.
This patch fixes sparse warnings and bugs on big endian systems.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Sun, 29 Apr 2018 12:31:49 +0000 (13:31 +0100)]
scsi: mpt3sas: fix spelling mistake: "disbale" -> "disable"
Trivial fix to spelling mistake in module parameter description text
[mkp: applied by hand]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Sun, 29 Apr 2018 12:25:32 +0000 (13:25 +0100)]
scsi: megaraid_sas: fix spelling mistake: "disbale" -> "disable"
Trivial fix to spelling mistake in module parameter description text
[mkp: applied by hand]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Fri, 27 Apr 2018 19:15:52 +0000 (20:15 +0100)]
scsi: esas2r: fix spelling mistake: "asynchromous" -> "asynchronous"
Trivial fix to spelling mistake in module description text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Wed, 25 Apr 2018 10:58:43 +0000 (11:58 +0100)]
scsi: isci: remove redundant check on in_connection_align_insertion_frequency
The sanity check on u->in_connection_align_insertion_frequency is being
performed twice and hence the first check can be removed since it is
redundant. Cleans up cppcheck warning:
drivers/scsi/ibmvscsi/ibmvscsi.c:1711: (warning) Identical inner 'if'
condition is always true.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Sat, 21 Apr 2018 10:58:35 +0000 (18:58 +0800)]
scsi: a100u2w: Use module_pci_driver
Remove boilerplate code by using macro module_pci_driver.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Sat, 21 Apr 2018 10:58:34 +0000 (18:58 +0800)]
scsi: wd719x: Use module_pci_driver
Remove boilerplate code by using macro module_pci_driver.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Sat, 21 Apr 2018 10:58:33 +0000 (18:58 +0800)]
scsi: am53c974: Use module_pci_driver
Remove boilerplate code by using macro module_pci_driver.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Sun, 15 Apr 2018 14:52:37 +0000 (16:52 +0200)]
scsi: scsi_transport_sas: don't bounce highmem pages for the smp handler
All three instance of ->smp_handler deal with highmem backed requests
just fine.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 20 Apr 2018 16:04:40 +0000 (18:04 +0200)]
scsi: ips: fix firmware timestamps for 32-bit
do_gettimeofday() is deprecated since it will stop working in 2038 on
32-bit platforms, leading to incorrect times passed to the firmware.
On 64-bit platforms the current code appears to be fine, as the
calculation passes an 8-bit century number into the firmware that can
represent times long in the future (possibly until 25599).
Using ktime_get_real_seconds() to get a 64-bit seconds value and
time64_to_tm() to convert it into the firmware format greatly simplifies
the ips timekeeping code, makes 32-bit and 64-bit behave the same way
here, and gets us closer to removing the deprecated interfaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Fri, 20 Apr 2018 16:02:09 +0000 (18:02 +0200)]
scsi: esas2r: use ktime_get_real_seconds()
do_gettimeofday() is deprecated because of the y2038 overflow. Here, we
use the result to pass into a 32-bit field in the firmware, which still
risks an overflow, but if the firmware is written to expect unsigned
values, it can at least last until y2106, and there is not much we can
do about it.
This changes do_gettimeofday() to ktime_get_real_seconds(), which at
least simplifies the code a bit, and avoids the deprecated
interface. I'm adding a comment about the overflow to document what
happens.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
YueHaibing [Thu, 29 Mar 2018 11:43:11 +0000 (19:43 +0800)]
scsi: mvumi: Using module_pci_driver
Remove boilerplate code by using macro module_pci_driver.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Randy Dunlap [Sat, 14 Apr 2018 17:51:06 +0000 (10:51 -0700)]
scsi: target: add driver-api document
Add a driver-api document for target/iSCSI interfaces.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
To: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: linux-scsi@vger.kernel.org
Cc: target-devel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Randy Dunlap [Sat, 14 Apr 2018 17:51:05 +0000 (10:51 -0700)]
scsi: target: target_core_user.[ch]: convert comments into DOC:
Make documentation on target-supported userspace-I/O design be
usable by kernel-doc by using "DOC:". This is used in the driver-api
Documentation chapter.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
To: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: linux-scsi@vger.kernel.org
Cc: target-devel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Randy Dunlap [Sat, 14 Apr 2018 17:51:04 +0000 (10:51 -0700)]
scsi: target: target_core_transport.c: enable+fix kernel-doc
For exported functions that already have near-kernel-doc notation,
fix them to begin with "/**" and make a few corrections so that they
don't have any kernel-doc warnings.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
To: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: linux-scsi@vger.kernel.org
Cc: target-devel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Randy Dunlap [Sat, 14 Apr 2018 17:51:03 +0000 (10:51 -0700)]
scsi: target: target_core_transport.c: fix kernel-doc warnings
Correct a function parameter's name to eliminate kernel-doc warnings
in drivers/target/target_core_transport.c.
Fixes these kernel-doc warnings: (tested by adding these files to a new
target.rst documentation file)
../drivers/target/target_core_transport.c:1671: warning: No description found for parameter 'fabric_tmr_ptr'
../drivers/target/target_core_transport.c:1671: warning: Excess function parameter 'fabric_context' description in 'target_submit_tmr'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
To: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: linux-scsi@vger.kernel.org
Cc: target-devel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jia-Ju Bai [Tue, 10 Apr 2018 12:38:42 +0000 (20:38 +0800)]
scsi: st: Replace GFP_ATOMIC with GFP_KERNEL in new_tape_buffer
new_tape_buffer() is never called in atomic context. new_tape_buffer()
is only called by st_probe(), which is only set as ".probe" in struct
scsi_driver.
Despite never getting called from atomic context, new_tape_buffer()
calls kzalloc() with GFP_ATOMIC, which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL, which
can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jia-Ju Bai [Tue, 10 Apr 2018 12:37:59 +0000 (20:37 +0800)]
scsi: st: Replace GFP_ATOMIC with GFP_KERNEL in st_probe
st_probe() is never called in atomic context. st_probe() is only set as
".probe" in struct scsi_driver.
Despite never getting called from atomic context, st_probe() calls
kzalloc() with GFP_ATOMIC, which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL, which
can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin Wilck [Tue, 17 Apr 2018 23:35:11 +0000 (01:35 +0200)]
scsi: devinfo: BLIST_RETRY_ASC_C1 for Fujitsu ETERNUS
On Fujitsu ETERNUS systems, sense code ABORTED COMMAND with ASC/Q C1/01
is used to indicate temporary condition where the storage-internal path
to a target is switched from one controller to another. SCSI commands
that return with this error code must be retried unconditionally
(i.e. without the "maybe_retry" logic in scsi_decide_disposition);
otherwise dm-multipath might initiate a failover from a healthy path
e.g. for REQ_FAILFAST_DEV commands.
Introduce a new blist flag for this case.
[mkp: applied by hand]
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin Wilck [Tue, 17 Apr 2018 23:35:10 +0000 (01:35 +0200)]
scsi: devinfo: add BLIST_RETRY_ITF for EMC Symmetrix
EMC Symmetrix returns 'internal target error' for a variety of
conditions, most of which will be transient. So we should always retry
it, even with failfast set. Otherwise we'd get spurious path flaps with
multipath.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin Wilck [Tue, 17 Apr 2018 23:35:09 +0000 (01:35 +0200)]
scsi: devinfo: warn on undefined blist flags
Warn if a device (or the user) sets blist flags which are unknown
or have been removed. This should enable us to reuse freed blist
bits in later releases.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin Wilck [Tue, 17 Apr 2018 23:35:08 +0000 (01:35 +0200)]
scsi: devinfo: change blist_flag_t to 64bit
Space for SCSI blist flags is gradually running out. Change the type to
__u64 and fix a checkpatch complaint about symbolic mode flags in
scsi_devinfo.c.
Make checkpatch happy by replacing simple_strtoul() with kstrtoull().
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin Wilck [Tue, 17 Apr 2018 23:35:07 +0000 (01:35 +0200)]
scsi: devinfo: use const_ilog2 for array indices
Use the just introduced const_ilog2() macro to avoid sparse errors.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Martin Wilck [Tue, 17 Apr 2018 23:35:06 +0000 (01:35 +0200)]
scsi: ilog2: create truly constant version for sparse
Sparse emits errors about ilog2() in array indices because of the use of
__ilog2_32() and __ilog2_64(), rightly so
(https://www.spinics.net/lists/linux-sparse/msg03471.html).
Create a const_ilog2() variant that works with sparse for this scenario.
(Note: checkpatch.pl complains about missing parentheses, but that
appears to be a false positive. I can get rid of the warning simply by
inserting whitespace, making checkpatch "see" the whole macro).
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Long Li [Thu, 19 Apr 2018 21:54:24 +0000 (14:54 -0700)]
scsi: storvsc: Select channel based on available percentage of ring buffer to write
This is a best effort for estimating on how busy the ring buffer is for
that channel, based on available buffer to write in percentage. It is
still possible that at the time of actual ring buffer write, the space
may not be available due to other processes may be writing at the time.
Selecting a channel based on how full it is can reduce the possibility
that a ring buffer write will fail, and avoid the situation a channel is
over busy.
Now it's possible that storvsc can use a smaller ring buffer size
(e.g. 40k bytes) to take advantage of cache locality.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Souptick Joarder [Sat, 14 Apr 2018 18:55:57 +0000 (00:25 +0530)]
scsi: target: Change return type to vm_fault_t
Use new return type vm_fault_t for fault handler in struct
vm_operations_struct.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lee Duncan [Fri, 6 Apr 2018 18:31:41 +0000 (11:31 -0700)]
scsi: target: prefer dbroot of /etc/target over /var/target
The target database root directory, dbroot, has defaulted to /var/target
for a while, but its main client, targetcli-fb, has been moving it to
/etc/target for quite some time. With the plethora of target drivers now
appearing, it has become more difficult to initialize this attribute
before use by any child drivers.
If the directory /etc/target exists, use that as the DB root. Otherwise,
fall back to using /var/target.
The ability to override this dbroot attribute still exists via sysfs.
Signed-off-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Wed, 18 Apr 2018 11:30:38 +0000 (12:30 +0100)]
scsi: mptfc: fix spelling mistake in macro names
Rename macros MPI_FCPORTPAGE0_SUPPORT_SPEED_UKNOWN and
MPI_FCPORTPAGE0_CURRENT_SPEED_UKNOWN to add in missing N in UNKNOWN
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Tue, 17 Apr 2018 01:04:40 +0000 (18:04 -0700)]
scsi: sd_zbc: Let the SCSI core handle ILLEGAL REQUEST / ASC 0x21
scsi_io_completion() translates the sense key ILLEGAL REQUEST / ASC 0x21 into
ACTION_FAIL. That means that setting cmd->allowed to zero in sd_zbc_complete()
for this sense code / ASC combination is not necessary. Hence remove the code
that resets cmd->allowed from sd_zbc_complete().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Tue, 17 Apr 2018 01:04:39 +0000 (18:04 -0700)]
scsi: sd_zbc: Change the type of the ZBC fields into u32
This patch does not change any functionality but makes it clear that it is on
purpose that these fields are 32 bits wide.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Mon, 16 Apr 2018 08:50:22 +0000 (10:50 +0200)]
scsi: storsvc: don't set a bounce limit
The default already is to never bounce, so the call is a no-op.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig [Mon, 16 Apr 2018 08:50:21 +0000 (10:50 +0200)]
scsi: iscsi_tcp: don't set a bounce limit
The default already is to never bounce, so the call is a no-op.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Souptick Joarder [Sat, 14 Apr 2018 18:47:41 +0000 (00:17 +0530)]
scsi: sg: Change return type to vm_fault_t
Use new return type vm_fault_t for fault handler in struct
vm_operations_struct.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Michael Schmitz [Thu, 12 Apr 2018 01:53:26 +0000 (13:53 +1200)]
scsi: zorro_esp: New driver for Amiga Zorro NCR53C9x boards
New combined SCSI driver for all ESP based Zorro SCSI boards for m68k Amiga.
Code largely based on board specific parts of the old drivers (blz1230.c,
blz2060.c, cyberstorm.c, cyberstormII.c, fastlane.c which were removed after
the 2.6 kernel series for lack of maintenance) with contributions by Tuomas
Vainikka (TCQ bug tests and workaround) and Finn Thain (TCQ bugfix by use of
PIO in extended message in transfer).
New Kconfig option and Makefile entries for new Amiga Zorro ESP SCSI driver
included in this patch.
Use DMA transfers wherever possible, with board-specific DMA set-up functions
copied from the old driver code. Three byte reselection messages do appear to
cause DMA timeouts. So wire up a PIO transfer routine for these
instead. esp_reselect_with_tag explicitly sets
esp->cmd_block_dma as target address for the message bytes but PIO
requires a virtual address. Substiute kernel virtual address
esp->cmd_block in PIO transfer call if DMA address is esp->cmd_block_dma
and phase is message in.
PIO code taken from mac_esp.c where the reselection timeout issue was debugged
and fixed first, with minor macro and function rename.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christian T. Steigies <cts@debian.org>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xose Vazquez Perez [Fri, 6 Apr 2018 22:47:23 +0000 (00:47 +0200)]
scsi: scsi_dh: replace too broad "TP9" string with the exact models
SGI/TP9100 is not an RDAC array:
^^^
https://git.opensvc.com/gitweb.cgi?p=multipath-tools/.git;a=blob;f=libmultipath/hwtable.c;h=
88b4700beb1d8940008020fbe4c3cd97d62f4a56;hb=HEAD#l235
This partially reverts commit
35204772ea03 ("[SCSI] scsi_dh_rdac :
Consolidate rdac strings together")
[mkp: fixed up the new entries to align with rest of struct]
Cc: NetApp RDAC team <ng-eseries-upstream-maintainers@netapp.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Cc: DM ML <dm-devel@redhat.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xose Vazquez Perez [Fri, 6 Apr 2018 22:15:07 +0000 (00:15 +0200)]
scsi: devinfo: delete duplicate "Generic"/"USB Storage-SMC" device
The revision field is currently unused by the devinfo pattern matching
code. Combine two blacklist entries into one.
$ egrep "Generic.*Storage-SMC" /proc/scsi/device_info
'Generic' 'USB Storage-SMC' 0x402
'Generic' 'USB Storage-SMC' 0x402
[mkp: tweaked commit desc]
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:33 +0000 (14:24 -0700)]
scsi: lpfc: update driver version to 12.0.0.2
Update the driver version to 12.0.0.2
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:32 +0000 (14:24 -0700)]
scsi: lpfc: Correct missing remoteport registration during link bounces
Remote port disappearance/reappearances would cause a series of RSCN
events to be delivered to the driver. During the resulting GID_FT
handling, the driver clears the fc4 settings on the remote port, which
makes it skip registration. As such, the nvme associations eventually
fail and return io errors to the applications.
Correct by not clearng the nlp_fc4_types for all nodes in
lpfc_issue_gidft. Instead, when the GID_FT response is handled, clear
the nlp_fc4_types of FCP and NVME prior to evaluating the fc4_type
returned by the GID_FT response. This approach leaves "skipped" nodes
with their nlp_fc4_types intacted.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:31 +0000 (14:24 -0700)]
scsi: lpfc: Fix NULL pointer reference when resetting adapter
Points referencing local port structures didn't accommodate cases where
the localport may not be registered yet.
Add NULL pointer checks to logic.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:30 +0000 (14:24 -0700)]
scsi: lpfc: Fix nvme remoteport registration race conditions
On tests adding and removing a remote port, calls to nvme_info would
eventually show fewer target ports discovered than were present in the
san. Additionally, the following error messages were seen:
6031 RemotePort Registration failed err: -116, DID x471301
There is a race condition that exists between the driver and the nvme
transport on remote port unregister vs the confirmed deletion. It's
possible that the driver may rediscover the remote port and reregister
the remote port before a prior unregister delete callback was made (as
it rebinded to the prior remoteport structure). However, the driver was
coded to expect the callback before seeing the remote port again thus a
new registration. The logic results in the driver having an invalid
remoteport pointer set.
Correct by tracking when waiting for the delete callback. In cases where
the ndlp remoteport pointer is updated, it is only cleared when the wait
has not been superceded by a prior registration.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:29 +0000 (14:24 -0700)]
scsi: lpfc: Fix driver not recovering NVME rports during target link faults
During target-side port faults, the driver would not recover all target
port logins. This resulted in a loss of nvme device discovery.
The driver is coded to wait for all GID_FT requests to complete before
restarting discovery. A fault is seen where the outstanding GIT_FT
counts are not properly decremented, thus discovery would never
start. Another fault was found in the clearing of the gidft_inp counter
that would be skipped in this condition. And a third fault found with
lpfc_nvme_register_port that would remove a reverence on the ndlp which
then allows a node swap on a port address change to prematurely remove
the reference and release the ndlp.
The following changes are made:
- Correct the decrementing of the outstanding GID_FT counters.
- In RSCN handling, no longer zero the counter before calling to issue
another GID_FT.
- No longer remove the reference on the dlp when the ndlp->nrport value
is not yet null.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:28 +0000 (14:24 -0700)]
scsi: lpfc: Fix WQ/CQ creation for older asic's.
The patch to enlarge WQ/CQ creation keys off of an adapter response that
indicates support for the larger values. Older adapters return an
incorrect response and are limited in size. Thus the adapters fail the
WQ creation steps.
Augment the WQ sizing checks with a check on the older adapter types and
limit them to the restricted sizes.
Fixes:
c176ffa0841c ("scsi: lpfc: Increase CQ and WQ sizes for SCSI")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:27 +0000 (14:24 -0700)]
scsi: lpfc: Fix NULL pointer access in lpfc_nvme_info_show
After making remoteport unregister requests, the ndlp nrport pointer was
stale.
Track when waiting for waiting for unregister completion callback and
adjust nldp pointer assignment. Add a few safety checks for NULL
pointer values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:26 +0000 (14:24 -0700)]
scsi: lpfc: Fix lingering lpfc_wq resource after driver unload
After driver unloads, lpfc_wq remains active. The destroy_workqueue
calls were not being made in driver unload. Additionally, SLI3 is
allocating lpfc_wq resources, but never uses it.
Make the destroy_workqueue calls on driver unload. Modify the SLI3 code
path no longer allocate lpfc_wq resources.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:25 +0000 (14:24 -0700)]
scsi: lpfc: Fix Abort request WQ selection
When running loads that generated aborts, io errors where seen. Turns
out the abort requests where not placed on the proper WQ resulting in
the errors. Closer inspection inspection of this error also showed
improper spinlock api use.
Correct the WQ selection policy for the abort requests. Correct
spin_lock/spin_lock_irq/spin_lock_irqsave usage.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:24 +0000 (14:24 -0700)]
scsi: lpfc: Enlarge nvmet asynchronous receive buffer counts
Under large io load, the current sizing of asynchronous buffer counts
could be exceeded, indicated by a 2885 log message:
2885 Port Status Event: port status reg 0x81800000, port smphr
reg 0xc000, error 1=0x52004a01, error 2=0x0
Enlarge the async receive queue size. Allow for a configurable number
of buffers to be posted to each RQ, using the new attribute
lpfc_nvmet_mrq_post.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:23 +0000 (14:24 -0700)]
scsi: lpfc: Add per io channel NVME IO statistics
When debugging various issues, per IO channel IO statistics were useful
to understand what was happening. However, many of the stats were on a
port basis rather than an io channel basis.
Move statistics to an io channel basis.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:22 +0000 (14:24 -0700)]
scsi: lpfc: Correct target queue depth application changes
The max_scsicmpl_time parameter can be used to perform scsi cmd queue
depth mgmt based on io completion time: the queue depth is reduced to
make completion time shorter. However, as soon as an io completes and
the completion time is within limits, the code immediately bumps the
queue depth limit back up to the target queue depth. Thus the procedure
restarts, effectively limiting the usefulness of adjusting queue depth
to help completion time.
This patch makes the following changes:
- Removes the code at io completion that resets the queue depth as soon
as within limits.
- As the code removed was where the target queue depth was first
applied, change target queue depth application so that it occurs when
the parameter is changed.
- Makes target queue depth a standard parameter: both a module
parameter and a sysfs parameter.
- Optimizes the command pending count by using atomics rather than
locks.
- Updates the debugfs nodelist stats to allow better debugging of
pending command counts.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Mon, 9 Apr 2018 21:24:21 +0000 (14:24 -0700)]
scsi: lpfc: Fix multiple PRLI completion error path
Nodelist entry for SCSI array ends up in UNMAPPED state. This is due to
illegal discovery State machine transition because of two PRLIs and the
first one failing with LS_RJT. Also, the error path was designed
assuming the PRLIs complete in the order they were sent, FCP first, then
NVME. In a failing case, the array thinks about the first PRLI (FCP),
but issues LS_RJT for the 2nd PRLI immediately.
Fix PRLI completion error path for the ordering expectation. Ensure the
discovery state machine update is not set until all outstanding PRLIs
are complete.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Fri, 6 Apr 2018 09:02:12 +0000 (02:02 -0700)]
scsi: megaraid_sas: driver version upgrade
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Fri, 6 Apr 2018 09:02:11 +0000 (02:02 -0700)]
scsi: megaraid_sas: Increase timeout by 1 sec for non-RAID fastpath IOs
Hardware could time out Fastpath IOs one second earlier than the timeout
provided by the host.
For non-RAID devices, driver provides timeout value based on OS provided
timeout value. Under certain scenarios, if the OS provides a timeout
value of 1 second, due to above behavior hardware will timeout
immediately.
Increase timeout value for non-RAID fastpath IOs by 1 second.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Himanshu Jha [Fri, 6 Apr 2018 09:02:10 +0000 (02:02 -0700)]
scsi: megaraid_sas: Use zeroing memory allocator than allocator/memset
Use pci_zalloc_consistent for allocating zeroed memory and remove
unnecessary memset function.
Done using Coccinelle.
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Long Li [Wed, 28 Mar 2018 00:48:39 +0000 (17:48 -0700)]
scsi: netvsc: Use the vmbus function to calculate ring buffer percentage
In Vmbus, we have defined a function to calculate available ring buffer
percentage to write.
Use that function and remove netvsc's private version.
[mkp: typo]
Signed-off-by: Long Li <longli@microsoft.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Long Li [Wed, 28 Mar 2018 00:48:38 +0000 (17:48 -0700)]
scsi: vmbus: Add function to report available ring buffer to write in total ring size percentage
Netvsc has a function to calculate how much ring buffer in percentage is
available to write. This function is also useful for storvsc and other
vmbus devices.
Define a similar function in vmbus to be used by other vmbus devices.
Signed-off-by: Long Li <longli@microsoft.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jason Yan [Mon, 26 Mar 2018 09:27:41 +0000 (17:27 +0800)]
scsi: libsas: add transport class for ATA devices
Now ata devices attached with sas controller do not have transport
class, so that we can not see any information of these ata devices in
/sys/class/ata_port(or ata_link or ata_device).
Add transport class for the ata devices attached with sas controller.
The /sys/class directory will show the infomation of the ata devices
as follows:
localhost:/sys/class # ls ata*
ata_device:
dev1.0 dev2.0
ata_link:
link1 link2
ata_port:
ata1 ata2
No functional change of the device scanning and io path. The ata
transport class was deleted when destroying the sas devices.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Fri, 23 Mar 2018 16:05:15 +0000 (00:05 +0800)]
scsi: hisi_sas: remove some unneeded structure members
This patch removes unneeded structure elements:
- hisi_sas_phy.dev_sas_addr: only ever written
- Also remove associated function which writes it,
hisi_sas_init_add().
- hisi_sas_device.attached_phy: only ever written
- Also remove code to set it in hisi_sas_dev_found()
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Fri, 23 Mar 2018 16:05:14 +0000 (00:05 +0800)]
scsi: hisi_sas: print device id for errors
When we find an erroneous slot completion, to help aid debugging add the
device index to the current debug log.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Fri, 23 Mar 2018 16:05:13 +0000 (00:05 +0800)]
scsi: hisi_sas: check IPTT is valid before using it for v3 hw
There is a bug of v3 hw development version. When AXI error happen, hw
may return an abnormal CQ that IPTT value is 0xffff. This will cause
IPTT out-of-bounds reference.
This patch adds a check of IPTT in cq_tasklet_v3_hw() and discards
invalid slot. This workaround scheme is just to enhance fault-tolerance
of the driver. So, we will apply this scheme for all version of v3 hw,
although release version has fixed this SoC bug.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Fri, 23 Mar 2018 16:05:12 +0000 (00:05 +0800)]
scsi: hisi_sas: consolidate command check in hisi_sas_get_ata_protocol()
Currently we check the fis->command value in 2 locations in
hisi_sas_get_ata_protocol() switch statement. Fix this by consolidating
the check for fis->command value to 1 location only.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 23 Mar 2018 16:05:11 +0000 (00:05 +0800)]
scsi: hisi_sas: use dma_zalloc_coherent()
This is a warning coming from Coccinelle, and need to use new interface
dma_zalloc_coherent() instead of dma_alloc_coherent()/memset().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 23 Mar 2018 16:05:10 +0000 (00:05 +0800)]
scsi: hisi_sas: delete timer when removing hisi_sas driver
Delete timer for v1 and v3 hw when removing hisi_sas driver.
Signed-off-by: Xiang chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Fri, 23 Mar 2018 16:05:09 +0000 (00:05 +0800)]
scsi: hisi_sas: update RAS feature for later revision of v3 HW
There is an modification for later revision of v3 hw. More HW errors are
reported through RAS interrupt. These errors were originally reported
only through MSI.
When report to RAS, some combinations are done to port AXI errors and
FIFO OMIT errors. For example, each port has 4 AXI errors, and they are
combined to one when report to RAS.
This patch does two things:
1. Enable RAS interrupt of these errors and handle them in PCI
error handlers.
2. Disable MSI interrupts of these errors for this later revision hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Fri, 23 Mar 2018 16:05:08 +0000 (00:05 +0800)]
scsi: hisi_sas: make SAS address of SATA disks unique
When directly connected with SATA disks in different SAS cores, fill SAS
address with scsi_host's id to make it's fake SAS address unique.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:35:42 +0000 (11:35 -0500)]
scsi: cxlflash: Handle spurious interrupts
The following Oops can occur when there is heavy I/O traffic and the host is
reset by a tool such as sg_reset.
[
c000200fff3fbc90]
c00800001690117c process_cmd_doneq+0x104/0x500
[cxlflash] (unreliable)
[
c000200fff3fbd80]
c008000016901648 cxlflash_rrq_irq+0xd0/0x150 [cxlflash]
[
c000200fff3fbde0]
c000000000193130 __handle_irq_event_percpu+0xa0/0x310
[
c000200fff3fbea0]
c0000000001933d8 handle_irq_event_percpu+0x38/0x90
[
c000200fff3fbee0]
c000000000193494 handle_irq_event+0x64/0xb0
[
c000200fff3fbf10]
c000000000198ea0 handle_fasteoi_irq+0xc0/0x230
[
c000200fff3fbf40]
c00000000019182c generic_handle_irq+0x4c/0x70
[
c000200fff3fbf60]
c00000000001794c __do_irq+0x7c/0x1c0
[
c000200fff3fbf90]
c00000000002a390 call_do_irq+0x14/0x24
[
c000200e5828fab0]
c000000000017b2c do_IRQ+0x9c/0x130
[
c000200e5828fb00]
c000000000009b04 h_virt_irq_common+0x114/0x120
When a context is reset, the pending commands are flushed and the AFU is
notified. Before the AFU handles this request there could be command
completion interrupts queued to PHB which are yet to be delivered to the
context. In this scenario, a context could receive an interrupt for a command
that has been flushed, leading to a possible crash when the memory for the
flushed command is accessed.
To resolve this problem, a boolean will indicate if the hardware queue is
ready to process interrupts or not. This can be evaluated in the interrupt
handler before proessing an interrupt.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:35:34 +0000 (11:35 -0500)]
scsi: cxlflash: Remove commmands from pending list on timeout
The following Oops can occur if an internal command sent to the AFU does not
complete within the timeout:
[
c000000ff101b810]
c008000016020d94 term_mc+0xfc/0x1b0 [cxlflash]
[
c000000ff101b8a0]
c008000016020fb0 term_afu+0x168/0x280 [cxlflash]
[
c000000ff101b930]
c0080000160232ec cxlflash_pci_error_detected+0x184/0x230
[cxlflash]
[
c000000ff101b9e0]
c00800000d95d468 cxl_vphb_error_detected+0x90/0x150[cxl]
[
c000000ff101ba20]
c00800000d95f27c cxl_pci_error_detected+0xa4/0x240 [cxl]
[
c000000ff101bac0]
c00000000003eaf8 eeh_report_error+0xd8/0x1b0
[
c000000ff101bb20]
c00000000003d0b8 eeh_pe_dev_traverse+0x98/0x170
[
c000000ff101bbb0]
c00000000003f438 eeh_handle_normal_event+0x198/0x580
[
c000000ff101bc60]
c00000000003fba4 eeh_handle_event+0x2a4/0x338
[
c000000ff101bd10]
c0000000000400b8 eeh_event_handler+0x1f8/0x200
[
c000000ff101bdc0]
c00000000013da48 kthread+0x1a8/0x1b0
[
c000000ff101be30]
c00000000000b528 ret_from_kernel_thread+0x5c/0xb4
When an internal command times out, the command buffer is freed while it is
still in the pending commands list of the context. This corrupts the list and
when the context is cleaned up, a crash is encountered.
To resolve this issue, when an AFU command or TMF command times out, the
command should be deleted from the hardware queue pending command list before
freeing the buffer.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:35:27 +0000 (11:35 -0500)]
scsi: cxlflash: Synchronize reset and remove ops
The following Oops can be encountered if a device removal or system shutdown
is initiated while an EEH recovery is in process:
[
c000000ff2f479c0]
c008000015256f18 cxlflash_pci_slot_reset+0xa0/0x100
[cxlflash]
[
c000000ff2f47a30]
c00800000dae22e0 cxl_pci_slot_reset+0x168/0x290 [cxl]
[
c000000ff2f47ae0]
c00000000003ef1c eeh_report_reset+0xec/0x170
[
c000000ff2f47b20]
c00000000003d0b8 eeh_pe_dev_traverse+0x98/0x170
[
c000000ff2f47bb0]
c00000000003f80c eeh_handle_normal_event+0x56c/0x580
[
c000000ff2f47c60]
c00000000003fba4 eeh_handle_event+0x2a4/0x338
[
c000000ff2f47d10]
c0000000000400b8 eeh_event_handler+0x1f8/0x200
[
c000000ff2f47dc0]
c00000000013da48 kthread+0x1a8/0x1b0
[
c000000ff2f47e30]
c00000000000b528 ret_from_kernel_thread+0x5c/0xb4
The remove handler frees AFU memory while the EEH recovery is in progress,
leading to a race condition. This can result in a crash if the recovery thread
tries to access this memory.
To resolve this issue, the cxlflash remove handler will evaluate the device
state and yield to any active reset or probing threads.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:35:21 +0000 (11:35 -0500)]
scsi: cxlflash: Enable OCXL operations
This commit enables the OCXL operations for the OCXL devices.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:35:15 +0000 (11:35 -0500)]
scsi: cxlflash: Support AFU reset
The cxlflash core driver resets the AFU when the master contexts are created
in the initialization or recovery paths. Today, the OCXL provider service to
perform this operation is pending implementation. To avoid a crash due to a
missing fop, log an error once and return success to continue with execution.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:35:07 +0000 (11:35 -0500)]
scsi: cxlflash: Register for translation errors
While enabling a context on the link, a predefined callback can be registered
with the OCXL provider services to be notified on translation errors. These
errors can in turn be passed back to the user on a read operation.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:35:00 +0000 (11:35 -0500)]
scsi: cxlflash: Introduce OCXL context state machine
In order to protect the OCXL hardware contexts from getting clobbered, a
simple state machine is added to indicate when a context is in open, close or
start state. The expected states are validated throughout the code to prevent
illegal operations on a context. A mutex is added to protect writes to the
context state field.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:34:55 +0000 (11:34 -0500)]
scsi: cxlflash: Update synchronous interrupt status bits
The SISLite specification has been updated to define new synchronous interrupt
status bits. These bits are set by the AFU when a given PASID or EA is bad and
a synchronous interrupt is triggered.
The SISLite header file is updated to support these new bits. Note that there
are also some formatting updates to some of the existing bits to allow all of
the definitions to line up uniformly.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:34:48 +0000 (11:34 -0500)]
scsi: cxlflash: Setup LISNs for master contexts
Similar to user contexts, master contexts also require that the per-context
LISN registers be programmed for certain AFUs. The mapped trigger page is
obtained from underlying transport and registered with AFU for each master
context.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:34:42 +0000 (11:34 -0500)]
scsi: cxlflash: Setup LISNs for user contexts
The SISLite specification has been updated for OCXL to support communicating
data to generate AFU interrupts to the AFU. This includes a new capability bit
that is advertised for OCXL AFUs and new registers to hold the object handle
and translation PASID of each interrupt. For Power, the object handle is the
mapped trigger page. Note that because these mappings are kernel only, the
PASID of a kernel context must be used to satisfy the translation.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:34:35 +0000 (11:34 -0500)]
scsi: cxlflash: Introduce object handle fop
OCXL requires that AFUs use an opaque object handle to represent an AFU
interrupt. The specification does not provide a common means to communicate
the object handle to the AFU - each AFU must define this within the AFU
specification. To support this model, the object handle must be passed back to
the core driver as it manages the AFU specification (SISLite) for cxlflash.
Note that for Power systems, the object handle is the effective address of the
trigger page.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:34:27 +0000 (11:34 -0500)]
scsi: cxlflash: Support file descriptor mapping
The cxlflash core fop API requires a way to invoke the fault and release
handlers of underlying transports using their native file-based APIs. This
provides the core with the ability to insert selectively itself into the
processing stream of these operations for cleanup. Implement these two fops to
map and release when requested.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:34:20 +0000 (11:34 -0500)]
scsi: cxlflash: Support adapter context mmap and release
The cxlflash userspace API requires that users be able to mmap and release the
adapter context. Support mapping by implementing the AFU mmap fop to map the
context MMIO space and install the corresponding page table entry upon page
fault. Similarly, implement the AFU release fop to terminate and clean up the
context when invoked.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:34:12 +0000 (11:34 -0500)]
scsi: cxlflash: Support adapter context reading
The cxlflash userspace API requires that users be able to read the adapter
context for any pending events or interrupts from the AFU. Support reading
various events by implementing the AFU read fop to copy out event data.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:34:03 +0000 (11:34 -0500)]
scsi: cxlflash: Support adapter context polling
The cxlflash userspace API requires that users be able to poll the adapter
context for any pending events or interrupts from the AFU. Support polling on
various events by implementing the AFU poll fop using a waitqueue.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:33:55 +0000 (11:33 -0500)]
scsi: cxlflash: Support starting user contexts
User contexts request interrupts and are started using the "start work"
interface. Populate the start_work() fop to allocate and map interrupts before
starting the user context. As part of starting the context, update the user
process identification logic to properly derive the data required by the
SPA. Also, introduce a skeleton interrupt handler using a bitmap, flag, and
spinlock to track interrupts. This handler will be expanded in future commits.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:33:48 +0000 (11:33 -0500)]
scsi: cxlflash: Support AFU interrupt mapping and registration
Add support to map and unmap the irq space and manage irq registrations with
the kernel for each allocated AFU interrupt. Also support mapping the physical
trigger page to obtain an effective address that will be provided to the
cxlflash core in a future commit.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:33:41 +0000 (11:33 -0500)]
scsi: cxlflash: Support AFU interrupt management
Add support to allocate and free AFU interrupts using the OCXL provider
services. The trigger page returned upon successful allocation will be mapped
and exposed to the cxlflash core in a future commit.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:33:35 +0000 (11:33 -0500)]
scsi: cxlflash: Support process element lifecycle
As part of the context lifecycle, the associated process element within the
Shared Process Area (SPA) of the link must be updated. Each process is defined
by various parameters (pid, tid, PASID mm) that are stored in the SPA upon
starting a context and invalidated when a context is stopped.
Use the OCXL provider services to configure the SPA with the appropriate data
that is unique to the process when starting a context. Initially only kernel
contexts are supported and therefore these process values are not applicable.
Note that the OCXL service used has an optional callback for translation fault
error notification. While not used here, it will be expanded in a future
commit.
Also add a service to stop a context by terminating the corresponding PASID
and remove the process element from the SPA.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:33:28 +0000 (11:33 -0500)]
scsi: cxlflash: Setup OCXL transaction layer
The first function of the link needs to configure the transaction layer
between the host and device. This is accomplished by a call to the OCXL
provider services.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:33:21 +0000 (11:33 -0500)]
scsi: cxlflash: Setup function OCXL link
After reading and modifying the function configuration, setup the OCXL link
using the OCXL provider services. The link is released when the adapter is
unconfigured.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:33:14 +0000 (11:33 -0500)]
scsi: cxlflash: Support reading adapter VPD data
Use the PCI VPD services to support reading the VPD data of the underlying
adapter.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:33:05 +0000 (11:33 -0500)]
scsi: cxlflash: Support AFU state toggling
The AFU should be enabled following a successful configuration and disabled
near the end of the cleanup path.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:32:56 +0000 (11:32 -0500)]
scsi: cxlflash: Support process specific mappings
Once the context is started, the assigned MMIO space can be mapped and
unmapped. Provide means to map and unmap the context MMIO space.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:32:48 +0000 (11:32 -0500)]
scsi: cxlflash: Support starting an adapter context
Once the adapter context is created, it needs to be started by assigning the
MMIO space for the context and by enabling the process element in the
link. This commit adds the skeleton for starting the context and assigns the
context specific MMIO space. Master contexts have access to the global MMIO
space while the rest have access to the context specific space.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:32:37 +0000 (11:32 -0500)]
scsi: cxlflash: MMIO map the AFU
When the AFU is configured, the global and per process MMIO regions are
presented by the configuration space. Save these regions and map the global
MMIO region that is used to access all of the control and provisioning data in
the AFU.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:32:29 +0000 (11:32 -0500)]
scsi: cxlflash: Support image reload policy modification
On a PERST, the AFU image can be reloaded or left intact. Provide means to set
this image reload policy.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:32:20 +0000 (11:32 -0500)]
scsi: cxlflash: Support adapter context discovery
Provide means to obtain the process element of an adapter context as well as
locate an adapter context by file.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:32:09 +0000 (11:32 -0500)]
scsi: cxlflash: Support adapter file descriptors for OCXL
Allocate a file descriptor for an adapter context when requested. In order to
allocate inodes for the file descriptors, a pseudo filesystem is created and
used.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Mon, 26 Mar 2018 16:32:00 +0000 (11:32 -0500)]
scsi: cxlflash: Use IDR to manage adapter contexts
A range of PASIDs are used as identifiers for the adapter contexts. These
contexts may be destroyed and created randomly. Use an IDR to keep track of
contexts that are in use and assign a unique identifier to new ones.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>