git.osdn.net Git - sagit-ice-cold/kernel_xiaomi

usb: chipidea: vbus event may exist before starting gadget

[ Upstream commit c3b674a04b8ab62a1d35e86714d466af0a0ecc18 ]

At some situations, the vbus may already be there before starting
gadget. So we need to check vbus event after switching to gadget in
order to handle missing vbus event. The typical use cases are plugging
vbus cable before driver load or the vbus has already been there
after stopping host but before starting gadget.

Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Stephen Boyd <stephen.boyd@linaro.org>
Reported-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

audit: log 32-bit socketcalls

[ Upstream commit 62bc306e2083436675e33b5bdeb6a77907d35971 ]

32-bit socketcalls were not being logged by audit on x86_64 systems.
Log them. This is basically a duplicate of the call from
net/socket.c:sys_socketcall(), but it addresses the impedance mismatch
between 32-bit userspace process and 64-bit kernel audit.

See: https://github.com/linux-audit/audit-kernel/issues/14

Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: dapm: handle probe deferrals

[ Upstream commit 37e1df8c95e2c8a57c77eafc097648f6e40a60ff ]

This starts to handle probe deferrals on regulators and clocks
on the ASoC DAPM.

I came to this patch after audio stopped working on Ux500 ages
ago and I finally looked into it to see what is wrong. I had
messages like this in the console since a while back:

ab8500-codec.0: ASoC: Failed to request audioclk: -517
ab8500-codec.0: ASoC: Failed to create DAPM control audioclk
ab8500-codec.0: Failed to create new controls -12
snd-soc-mop500.0: ASoC: failed to instantiate card -12
snd-soc-mop500.0: Error: snd_soc_register_card failed (-12)!
snd-soc-mop500: probe of snd-soc-mop500.0 failed with error -12

Apparently because the widget table for the codec looks like
this (sound/soc/codecs/ab8500-codec.c):

static const struct snd_soc_dapm_widget ab8500_dapm_widgets[] = {

        /* Clocks */
        SND_SOC_DAPM_CLOCK_SUPPLY("audioclk"),

        /* Regulators */
        SND_SOC_DAPM_REGULATOR_SUPPLY("V-AUD", 0, 0),
        SND_SOC_DAPM_REGULATOR_SUPPLY("V-AMIC1", 0, 0),
        SND_SOC_DAPM_REGULATOR_SUPPLY("V-AMIC2", 0, 0),
        SND_SOC_DAPM_REGULATOR_SUPPLY("V-DMIC", 0, 0),

So when we call snd_soc_register_codec() and any of these widgets
get a deferred probe we do not get an -EPROBE_DEFER (-517) back as
we should and instead we just fail. Apparently the code assumes
that clocks and regulators must be available at this point and
not defer.

After this patch it rather looks like this:

ab8500-codec.0: Failed to create new controls -517
snd-soc-mop500.0: ASoC: failed to instantiate card -517
snd-soc-mop500.0: Error: snd_soc_register_card failed (-517)!
(...)
abx500-clk.0: registered clocks for ab850x
snd-soc-mop500.0: ab8500-codec-dai.0 <-> ux500-msp-i2s.1 mapping ok
snd-soc-mop500.0: ab8500-codec-dai.1 <-> ux500-msp-i2s.3 mapping ok

I'm pretty happy about the patch as it it, but I'm a bit
uncertain on how to proceed: there are a lot of users of the
external functions snd_soc_dapm_new_control() (111 sites)
and that will now return an occassional error pointer, which
is not handled in the calling sites.

I want an indication from the maintainers whether I should just
go in and augment all these call sites, or if deferred probe
is frowned upon when it leads to this much overhead.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

partitions/efi: Fix integer overflow in GPT size calculation

[ Upstream commit c5082b70adfe8e1ea1cf4a8eff92c9f260e364d2 ]

If a GUID Partition Table claims to have more than 2**25 entries, the
calculation of the partition table size in alloc_read_gpt_entries() will
overflow a 32-bit integer and not enough space will be allocated for the
table.

Nothing seems to get written out of bounds, but later efi_partition() will
read up to 32768 bytes from a 128 byte buffer, possibly OOPSing or exposing
information to /proc/partitions and uevents.

The problem exists on both 64-bit and 32-bit platforms.

Fix the overflow and also print a meaningful debug message if the table
size is too large.

Signed-off-by: Alden Tondettar <alden.tondettar@gmail.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: mos7840: fix control-message error handling

[ Upstream commit cd8db057e93ddaacbec025b567490555d2bca280 ]

Make sure to detect short transfers when reading a device register.

The modem-status handling had sufficient error checks in place, but move
handling of short transfers into the register accessor function itself
for consistency.

Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: mos7720: fix control-message error handling

[ Upstream commit 0d130367abf582e7cbf60075c2a7ab53817b1d14 ]

Make sure to log an error on short transfers when reading a device
register.

Also clear the provided buffer (which if often an uninitialised
automatic variable) on errors as the driver currently does not bother to
check for errors.

Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdkfd: fix improper return value on error

[ Upstream commit 8bf793883da213864efc50c274d2b38ec0ca58b2 ]

In function kfd_wait_on_events(), when the call to copy_from_user()
fails, the value of return variable ret is 0. 0 indicates success, which
is inconsistent with the execution status. This patch fixes the bug by
assigning "-EFAULT" to ret when copy_from_user() returns an unexpected
value.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/ipoib: Replace list_del of the neigh->list with list_del_init

[ Upstream commit c586071d1dc8227a7182179b8e50ee92cc43f6d2 ]

In order to resolve a situation where a few process delete
the same list element in sequence and cause panic, list_del
is replaced with list_del_init. In this case if the first
process that calls list_del releases the lock before acquiring
it again, other processes who can acquire the lock will call
list_del_init.

Fixes: b63b70d87741 ("IPoIB: Use a private hash table for path lookup")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/ipoib: rtnl_unlock can not come after free_netdev

[ Upstream commit 89a3987ab7a923c047c6dec008e60ad6f41fac22 ]

The ipoib_vlan_add function calls rtnl_unlock after free_netdev,
rtnl_unlock not only releases the lock, but also calls netdev_run_todo.
The latter function browses the net_todo_list array and completes the
unregistration of all its net_device instances. If we call free_netdev
before rtnl_unlock, then netdev_run_todo call over the freed device causes
panic.
To fix, move rtnl_unlock call before free_netdev call.

Fixes: 9baa0b036410 ("IB/ipoib: Add rtnl_link_ops support")
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/ipoib: Fix deadlock over vlan_mutex

[ Upstream commit 1c3098cdb05207e740715857df7b0998e372f527 ]

This patch fixes Deadlock while executing ipoib_vlan_delete.

The function takes the vlan_rwsem semaphore and calls
unregister_netdevice. The later function calls
ipoib_mcast_stop_thread that cause workqueue flush.

When the queue has one of the ipoib_ib_dev_flush_xxx events,
a deadlock occur because these events also tries to catch the
same vlan_rwsem semaphore.

To fix, unregister_netdevice should be called after releasing
the semaphore.

Fixes: cbbe1efa4972 ("IPoIB: Fix deadlock between ipoib_open() and child interface create")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: goldfish: Fix a parameter of a call to free_irq

[ Upstream commit 1a5c2d1de7d35f5eb9793266237903348989502b ]

'request_irq()' and 'free_irq()' should be called with the same dev_id.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8635/1: nommu: allow enabling REMAP_VECTORS_TO_RAM

[ Upstream commit 8a792e9afbce84a0fdaf213fe42bb97382487094 ]

REMAP_VECTORS_TO_RAM depends on DRAM_BASE, but since DRAM_BASE is a
hex, REMAP_VECTORS_TO_RAM could never get enabled. Also depending on
DRAM_BASE is redundant as whenever REMAP_VECTORS_TO_RAM makes itself
available to Kconfig, DRAM_BASE also is available as the Kconfig
gets sourced on !MMU.

Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: hx711: Add DT binding for avia,hx711

[ Upstream commit ff1293f67734da68e23fecb6ecdae7112b8c43f9 ]

Add DT bindings for avia,hx711
Add vendor avia to vendor list

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: axp288: Drop bogus AXP288_ADC_TS_PIN_CTRL register modifications

[ Upstream commit fa2849e9649b5180ffc4cb3c3b005261c403093a ]

For some reason the axp288_adc driver was modifying the
AXP288_ADC_TS_PIN_CTRL register, changing bits 0-1 depending on
whether the GP_ADC channel or another channel was written.

These bits control when a bias current is send to the TS_PIN, the
GP_ADC has its own pin and a separate bit in another register to
control the bias current.

Not only does changing when to enable the TS_PIN bias current
(always or only when sampling) when reading the GP_ADC make no sense
at all, the code is modifying these bits is writing the entire register,
assuming that all the other bits have their default value.

So if the firmware has configured a different bias-current for either
pin, then that change gets clobbered by the write, likewise if the
firmware has set bit 2 to indicate that the battery has no thermal sensor,
this will get clobbered by the write.

This commit fixes all this, by simply removing all writes to the
AXP288_ADC_TS_PIN_CTRL register, they are not needed to read the
GP_ADC pin, and can actually be harmful.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (gl520sm) Fix overflows and crash seen when writing into limit attributes

[ Upstream commit 87cdfa9d60f4f40e6d71b04b10b36d9df3c89282 ]

Writes into limit attributes can overflow due to multplications and
additions with unbound input values. Writing into fan limit attributes
can result in a crash with a division by zero if very large values are
written and the fan divider is larger than 1.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sh_eth: use correct name for ECMR_MPDE bit

[ Upstream commit 6dcf45e514974a1ff10755015b5e06746a033e5f ]

This bit was wrongly named due to a typo, Sergei checked the SH7734/63
manuals and this bit should be named MPDE.

Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

extcon: axp288: Use vbus-valid instead of -present to determine cable presence

[ Upstream commit 5757aca10146061befd168dab37fb0db1ccd8f73 ]

The vbus-present bit in the power status register also gets set to 1
when a usb-host cable (id-pin shorted to ground) is plugged in and a 5v
boost converter is supplying 5v to the otg usb bus.

This causes a "disconnect or unknown or ID event" warning in dmesg as
well as the extcon device to report the last detected charger cable
type as being connected even though none is connected.

This commit switches to checking the vbus-valid bit instead, which is
only 1 when both vbus is present and the vbus-path is enabled in the
vbus-path control register (the vbus-path gets disabled when a usb-host
cable is detected, to avoid the pmic drawing power from the 5v boost
converter).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

igb: re-assign hw address pointer on reset after PCI error

[ Upstream commit 69b97cf6dbce7403845a28bbc75d57f5be7b12ac ]

Whenever the igb driver detects the result of a read operation returns
a value composed only by F's (like 0xFFFFFFFF), it will detach the
net_device, clear the hw_addr pointer and warn to the user that adapter's
link is lost - those steps happen on igb_rd32().

In case a PCI error happens on Power architecture, there's a recovery
mechanism called EEH, that will reset the PCI slot and call driver's
handlers to reset the adapter and network functionality as well.

We observed that once hw_addr is NULL after the error is detected on
igb_rd32(), it's never assigned back, so in the process of resetting
the network functionality we got a NULL pointer dereference in both
igb_configure_tx_ring() and igb_configure_rx_ring(). In order to avoid
such bug, this patch re-assigns the hw_addr value in the slot_reset
handler.

Reported-by: Anthony H Thai <ahthai@us.ibm.com>
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ralink: Fix incorrect assignment on ralink_soc

[ Upstream commit 08d90c81b714482dceb5323d14f6617bcf55ee61 ]

ralink_soc sould be assigned to RT3883_SOC, replace incorrect
comparision with assignment.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Fixes: 418d29c87061 ("MIPS: ralink: Unify SoC id handling")
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14903/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Ensure bss section ends on a long-aligned address

[ Upstream commit 3f00f4d8f083bc61005d0a1ef592b149f5c88bbd ]

When clearing the .bss section in kernel_entry we do so using LONG_S
instructions, and branch whilst the current write address doesn't equal
the end of the .bss section minus the size of a long integer. The .bss
section always begins at a long-aligned address and we always increment
the write pointer by the size of a long integer - we therefore rely upon
the .bss section ending at a long-aligned address. If this is not the
case then the long-aligned write address can never be equal to the
non-long-aligned end address & we will continue to increment past the
end of the .bss section, attempting to zero the rest of memory.

Despite this requirement that .bss end at a long-aligned address we pass
0 as the end alignment requirement to the BSS_SECTION macro and thus
don't guarantee any particular alignment, allowing us to hit the error
condition described above.

Fix this by instead passing 8 bytes as the end alignment argument to
the BSS_SECTION macro, ensuring that the end of the .bss section is
always at least long-aligned.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14526/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for msiof nodes

[ Upstream commit 654450baf2afba86cf328e1849ccac61ec4630af ]

Use recently added R-Car Gen 2 fallback binding for msiof nodes in
DT for r8a7790 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7790 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDS: RDMA: Fix the composite message user notification

[ Upstream commit 941f8d55f6d613a460a5e080d25a38509f45eb75 ]

When application sends an RDS RDMA composite message consist of
RDMA transfer to be followed up by non RDMA payload, it expect to
be notified *only* when the full message gets delivered. RDS RDMA
notification doesn't behave this way though.

Thanks to Venkat for debug and root casuing the issue
where only first part of the message(RDMA) was
successfully delivered but remainder payload delivery failed.
In that case, application should not be notified with
a false positive of message delivery success.

Fix this case by making sure the user gets notified only after
the full message delivery.

Reviewed-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

GFS2: Fix reference to ERR_PTR in gfs2_glock_iter_next

[ Upstream commit 14d37564fa3dc4e5d4c6828afcd26ac14e6796c5 ]

This patch fixes a place where function gfs2_glock_iter_next can
reference an invalid error pointer.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm: bridge: add DT bindings for TI ths8135

[ Upstream commit 2e644be30fcc08c736f66b60f4898d274d4873ab ]

THS8135 is a configurable video DAC. Add DT bindings for this chip.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481623759-12786-3-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm_fourcc: Fix DRM_FORMAT_MOD_LINEAR #define

[ Upstream commit af913418261d6d3e7a29f06cf35f04610ead667c ]

We need to define DRM_FORMAT_MOD_VENDOR_NONE for the fourcc_mod_code()
macro to work correctly.

Signed-off-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1481657272-25975-1-git-send-email-hoegsberg@google.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.90

fix xen_swiotlb_dma_mmap prototype

xen_swiotlb_dma_mmap was backported from v4.10, but older
kernels before commit 00085f1efa38 ("dma-mapping: use unsigned long
for dma_attrs") use a different signature:

arm/xen/mm.c:202:10: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.mmap = xen_swiotlb_dma_mmap,
^~~~~~~~~~~~~~~~~~~~
arm/xen/mm.c:202:10: note: (near initialization for 'xen_swiotlb_dma_ops.mmap')

This adapts the patch to the old calling conventions.

Fixes: "swiotlb-xen: implement xen_swiotlb_dma_mmap callback"
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

swiotlb-xen: implement xen_swiotlb_dma_mmap callback

commit 7e91c7df29b5e196de3dc6f086c8937973bd0b88 upstream.

This function creates userspace mapping for the DMA-coherent memory.

Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Oleksandr Dmytryshyn <oleksandr.dmytryshyn@globallogic.com>
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

video: fbdev: aty: do not leak uninitialized padding in clk to userspace

commit 8e75f7a7a00461ef6d91797a60b606367f6e344d upstream.

'clk' is copied to a userland with padding byte(s) after 'vclk_post_div'
field unitialized, leaking data from the stack. Fix this ensuring all of
'clk' is initialized to zero.

References: https://github.com/torvalds/linux/pull/441
Reported-by: sohu0106 <sohu0106@126.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: VMX: use cmpxchg64

commit c0a1666bcb2a33e84187a15eabdcd54056be9a97 upstream.

This fixes a compilation failure on 32-bit systems.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: pxa: fix the number of DMA requestor lines

commit 4c35430ad18f5a034302cb90e559ede5a27f93b9 upstream.

The number of requestor lines was clamped to 0 for all pxa architectures
in the requestor declaration. Fix this by using the value.

Fixes: 72b195cb7162 ("ARM: pxa: add the number of DMA requestor lines")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: pxa: add the number of DMA requestor lines

commit 72b195cb716284217e8b270af420bc7e5cf04b3c upstream.

Declare the number of DMA requestor lines per platform :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines

This information will be used to activate the DMA flow control or not.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: mmp-pdma: add number of requestors

commit c283e41ef32442f41e7180f9bb1c5aedf9255bfe upstream.

The DMA chip has a fixed number of requestor lines used for flow
control. This number is platform dependent. The pxa_dma dma driver will
use this value to activate or not the flow control.

There won't be any impact on mmp_pdma driver.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxl: Fix driver use count

commit 197267d0356004a31c4d6b6336598f5dff3301e1 upstream.

cxl keeps a driver use count, which is used with the hash memory model
on p8 to know when to upgrade local TLBIs to global and to trigger
callbacks to manage the MMU for PSL8.

If a process opens a context and closes without attaching or fails the
attachment, the driver use count is never decremented. As a
consequence, TLB invalidations remain global, even if there are no
active cxl contexts.

We should increment the driver use count when the process is attaching
to the cxl adapter, and not on open. It's not needed before the
adapter starts using the context and the use count is decremented on
the detach path, so it makes more sense.

It affects only the user api. The kernel api is already doing The
Right Thing.

Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Fixes: 7bb5d91a4dda ("cxl: Rework context lifetimes")
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[ajd: backport to stable v4.4 tree]
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: VMX: remove WARN_ON_ONCE in kvm_vcpu_trigger_posted_interrupt

commit 5753743fa5108b8f98bd61e40dc63f641b26c768 upstream.

WARN_ON_ONCE(pi_test_sn(&vmx->pi_desc)) in kvm_vcpu_trigger_posted_interrupt()
intends to detect the violation of invariant that VT-d PI notification
event is not suppressed when vcpu is in the guest mode. Because the
two checks for the target vcpu mode and the target suppress field
cannot be performed atomically, the target vcpu mode may change in
between. If that does happen, WARN_ON_ONCE() here may raise false
alarms.

As the previous patch fixed the real invariant breaker, remove this
WARN_ON_ONCE() to avoid false alarms, and document the allowed cases
instead.

Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reported-by: "Ramamurthy, Venkatesh" <venkatesh.ramamurthy@intel.com>
Reported-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes: 28b835d60fcc ("KVM: Update Posted-Interrupts Descriptor when vCPU is preempted")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: VMX: do not change SN bit in vmx_update_pi_irte()

commit dc91f2eb1a4021eb6705c15e474942f84ab9b211 upstream.

In kvm_vcpu_trigger_posted_interrupt() and pi_pre_block(), KVM
assumes that PI notification events should not be suppressed when the
target vCPU is not blocked.

vmx_update_pi_irte() sets the SN field before changing an interrupt
from posting to remapping, but it does not check the vCPU mode.
Therefore, the change of SN field may break above the assumption.
Besides, I don't see reasons to suppress notification events here, so
remove the changes of SN field to avoid race condition.

Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reported-by: "Ramamurthy, Venkatesh" <venkatesh.ramamurthy@intel.com>
Reported-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes: 28b835d60fcc ("KVM: Update Posted-Interrupts Descriptor when vCPU is preempted")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

timer/sysclt: Restrict timer migration sysctl values to 0 and 1

commit b94bf594cf8ed67cdd0439e70fa939783471597a upstream.

timer_migration sysctl acts as a boolean switch, so the allowed values
should be restricted to 0 and 1.

Add the necessary extra fields to the sysctl table entry to enforce that.

[ tglx: Rewrote changelog ]

Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Link: http://lkml.kernel.org/r/1492640690-3550-1-git-send-email-mhjungk@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kazuhiro Hayashi <kazuhiro3.hayashi@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gfs2: Fix debugfs glocks dump

commit 10201655b085df8e000822e496e5d4016a167a36 upstream.

The switch to rhashtables (commit 88ffbf3e03) broke the debugfs glock
dump (/sys/kernel/debug/gfs2/<device>/glocks) for dumps bigger than a
single buffer: the right function for restarting an rhashtable iteration
from the beginning of the hash table is rhashtable_walk_enter;
rhashtable_walk_stop + rhashtable_walk_start will just resume from the
current position.

The upstream commit doesn't directly apply to 4.4.y because 4.4.y
doesn't have rhashtable_walk_enter and the following mainline commits:

  92ecd73a887c4a2b94daf5fc35179d75d1c4ef95
    gfs2: Deduplicate gfs2_{glocks,glstats}_open
  cc37a62785a584f4875788689f3fd1fa6e4eb291
    gfs2: Replace rhashtable_walk_init with rhashtable_walk_enter

Other than rhashtable_walk_enter, rhashtable_walk_init can fail.  To
handle the failure case in gfs2_glock_seq_stop, we check if
rhashtable_walk_init has initialized iter->walker; if it has not, we
must not call rhashtable_walk_stop or rhashtable_walk_exit.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/fpu: Don't let userspace set bogus xcomp_bv

commit 814fb7bb7db5433757d76f4c4502c96fc53b0b5e upstream.

[Please apply to 4.4-stable.  Note: the backport includes the
fpstate_init() call in xstateregs_set(), since fix is useless without
it.  It was added by commit 91c3dba7dbc1 ("x86/fpu/xstate: Fix PTRACE
frames for XSAVES"), but it doesn't make sense to backport that whole
commit.]

On x86, userspace can use the ptrace() or rt_sigreturn() system calls to
set a task's extended state (xstate) or "FPU" registers.  ptrace() can
set them for another task using the PTRACE_SETREGSET request with
NT_X86_XSTATE, while rt_sigreturn() can set them for the current task.
In either case, registers can be set to any value, but the kernel
assumes that the XSAVE area itself remains valid in the sense that the
CPU can restore it.

However, in the case where the kernel is using the uncompacted xstate
format (which it does whenever the XSAVES instruction is unavailable),
it was possible for userspace to set the xcomp_bv field in the
xstate_header to an arbitrary value.  However, all bits in that field
are reserved in the uncompacted case, so when switching to a task with
nonzero xcomp_bv, the XRSTOR instruction failed with a #GP fault.  This
caused the WARN_ON_FPU(err) in copy_kernel_to_xregs() to be hit.  In
addition, since the error is otherwise ignored, the FPU registers from
the task previously executing on the CPU were leaked.

Fix the bug by checking that the user-supplied value of xcomp_bv is 0 in
the uncompacted case, and returning an error otherwise.

The reason for validating xcomp_bv rather than simply overwriting it
with 0 is that we want userspace to see an error if it (incorrectly)
provides an XSAVE area in compacted format rather than in uncompacted
format.

Note that as before, in case of error we clear the task's FPU state.
This is perhaps non-ideal, especially for PTRACE_SETREGSET; it might be
better to return an error before changing anything.  But it seems the
"clear on error" behavior is fine for now, and it's a little tricky to
do otherwise because it would mean we couldn't simply copy the full
userspace state into kernel memory in one __copy_from_user().

This bug was found by syzkaller, which hit the above-mentioned
WARN_ON_FPU():

    WARNING: CPU: 1 PID: 0 at ./arch/x86/include/asm/fpu/internal.h:373 __switch_to+0x5b5/0x5d0
    CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.13.0 #453
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
    task: ffff9ba2bc8e42c0 task.stack: ffffa78cc036c000
    RIP: 0010:__switch_to+0x5b5/0x5d0
    RSP: 0000:ffffa78cc08bbb88 EFLAGS: 00010082
    RAX: 00000000fffffffe RBX: ffff9ba2b8bf2180 RCX: 00000000c0000100
    RDX: 00000000ffffffff RSI: 000000005cb10700 RDI: ffff9ba2b8bf36c0
    RBP: ffffa78cc08bbbd0 R08: 00000000929fdf46 R09: 0000000000000001
    R10: 0000000000000000 R11: 0000000000000000 R12: ffff9ba2bc8e42c0
    R13: 0000000000000000 R14: ffff9ba2b8bf3680 R15: ffff9ba2bf5d7b40
    FS:  00007f7e5cb10700(0000) GS:ffff9ba2bf400000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 00000000004005cc CR3: 0000000079fd5000 CR4: 00000000001406e0
    Call Trace:
    Code: 84 00 00 00 00 00 e9 11 fd ff ff 0f ff 66 0f 1f 84 00 00 00 00 00 e9 e7 fa ff ff 0f ff 66 0f 1f 84 00 00 00 00 00 e9 c2 fa ff ff <0f> ff 66 0f 1f 84 00 00 00 00 00 e9 d4 fc ff ff 66 66 2e 0f 1f

Here is a C reproducer.  The expected behavior is that the program spin
forever with no output.  However, on a buggy kernel running on a
processor with the "xsave" feature but without the "xsaves" feature
(e.g. Sandy Bridge through Broadwell for Intel), within a second or two
the program reports that the xmm registers were corrupted, i.e. were not
restored correctly.  With CONFIG_X86_DEBUG_FPU=y it also hits the above
kernel warning.

    #define _GNU_SOURCE
    #include <stdbool.h>
    #include <inttypes.h>
    #include <linux/elf.h>
    #include <stdio.h>
    #include <sys/ptrace.h>
    #include <sys/uio.h>
    #include <sys/wait.h>
    #include <unistd.h>

    int main(void)
    {
        int pid = fork();
        uint64_t xstate[512];
        struct iovec iov = { .iov_base = xstate, .iov_len = sizeof(xstate) };

        if (pid == 0) {
            bool tracee = true;
            for (int i = 0; i < sysconf(_SC_NPROCESSORS_ONLN) && tracee; i++)
                tracee = (fork() != 0);
            uint32_t xmm0[4] = { [0 ... 3] = tracee ? 0x00000000 : 0xDEADBEEF };
            asm volatile("   movdqu %0, %%xmm0\n"
                         "   mov %0, %%rbx\n"
                         "1: movdqu %%xmm0, %0\n"
                         "   mov %0, %%rax\n"
                         "   cmp %%rax, %%rbx\n"
                         "   je 1b\n"
                         : "+m" (xmm0) : : "rax", "rbx", "xmm0");
            printf("BUG: xmm registers corrupted!  tracee=%d, xmm0=%08X%08X%08X%08X\n",
                   tracee, xmm0[0], xmm0[1], xmm0[2], xmm0[3]);
        } else {
            usleep(100000);
            ptrace(PTRACE_ATTACH, pid, 0, 0);
            wait(NULL);
            ptrace(PTRACE_GETREGSET, pid, NT_X86_XSTATE, &iov);
            xstate[65] = -1;
            ptrace(PTRACE_SETREGSET, pid, NT_X86_XSTATE, &iov);
            ptrace(PTRACE_CONT, pid, 0, 0);
            wait(NULL);
        }
        return 1;
    }

Note: the program only tests for the bug using the ptrace() system call.
The bug can also be reproduced using the rt_sigreturn() system call, but
only when called from a 32-bit program, since for 64-bit programs the
kernel restores the FPU state from the signal frame by doing XRSTOR
directly from userspace memory (with proper error checking).

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Eric Biggers <ebiggers3@gmail.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Kevin Hao <haokexin@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: Yu-cheng Yu <yu-cheng.yu@intel.com>
Cc: kernel-hardening@lists.openwall.com
Fixes: 0b29643a5843 ("x86/xsaves: Change compacted format xsave area header")
Link: http://lkml.kernel.org/r/20170922174156.16780-2-ebiggers3@gmail.com
Link: http://lkml.kernel.org/r/20170923130016.21448-25-mingo@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: prevent to set invalid default subvolid

commit 6d6d282932d1a609e60dc4467677e0e863682f57 upstream.

`btrfs sub set-default` succeeds to set an ID which isn't corresponding to any
fs/file tree. If such the bad ID is set to a filesystem, we can't mount this
filesystem without specifying `subvol` or `subvolid` mount options.

Fixes: 6ef5ed0d386b ("Btrfs: add ioctl and incompat flag to set the default mount subvol")
Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: propagate error to btrfs_cmp_data_prepare caller

commit 78ad4ce014d025f41b8dde3a81876832ead643cf upstream.

btrfs_cmp_data_prepare() (almost) always returns 0 i.e. ignoring errors
from gather_extent_pages(). While the pages are freed by
btrfs_cmp_data_free(), cmp->num_pages still has > 0. Then,
btrfs_extent_same() try to access the already freed pages causing faults
(or violates PageLocked assertion).

This patch just return the error as is so that the caller stop the process.

Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Fixes: f441460202cb ("btrfs: fix deadlock with extent-same and readpage")
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix NULL pointer dereference from free_reloc_roots()

commit bb166d7207432d3c7d10c45dc052f12ba3a2121d upstream.

__del_reloc_root should be called before freeing up reloc_root->node.
If not, calling __del_reloc_root() dereference reloc_root->node, causing
the system BUG.

Fixes: 6bdf131fac23 ("Btrfs: don't leak reloc root nodes on error")
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Fix race condition with driver_override

commit 9561475db680f7144d2223a409dd3d7e322aca03 upstream.

The driver_override implementation is susceptible to a race condition when
different threads are reading vs. storing a different driver override. Add
locking to avoid the race condition.

This is in close analogy to commit 6265539776a0 ("driver core: platform:
fix race condition with driver_override") from Adrian Salido.

Fixes: 782a985d7af2 ("PCI: Introduce new device binding path using pci_dev.driver_override")
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kvm: nVMX: Don't allow L2 to access the hardware CR8

commit 51aa68e7d57e3217192d88ce90fd5b8ef29ec94f upstream.

If L1 does not specify the "use TPR shadow" VM-execution control in
vmcs12, then L0 must specify the "CR8-load exiting" and "CR8-store
exiting" VM-execution controls in vmcs02. Failure to do so will give
the L2 VM unrestricted read/write access to the hardware CR8.

This fixes CVE-2017-12154.

Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: VMX: Do not BUG() on out-of-bounds guest IRQ

commit 3a8b0677fc6180a467e26cc32ce6b0c09a32f9bb upstream.

The value of the guest_irq argument to vmx_update_pi_irte() is
ultimately coming from a KVM_IRQFD API call. Do not BUG() in
vmx_update_pi_irte() if the value is out-of bounds. (Especially,
since KVM as a whole seems to hang after that.)

Instead, print a message only once if we find that we don't have a
route for a certain IRQ (which can be out-of-bounds or within the
array).

This fixes CVE-2017-1000252.

Fixes: efc644048ecde54 ("KVM: x86: Update IRTE for posted-interrupts")
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: fault: Route pte translation faults via do_translation_fault

commit 760bfb47c36a07741a089bf6a28e854ffbee7dc9 upstream.

We currently route pte translation faults via do_page_fault, which elides
the address check against TASK_SIZE before invoking the mm fault handling
code. However, this can cause issues with the path walking code in
conjunction with our word-at-a-time implementation because
load_unaligned_zeropad can end up faulting in kernel space if it reads
across a page boundary and runs into a page fault (e.g. by attempting to
read from a guard region).

In the case of such a fault, load_unaligned_zeropad has registered a
fixup to shift the valid data and pad with zeroes, however the abort is
reported as a level 3 translation fault and we dispatch it straight to
do_page_fault, despite it being a kernel address. This results in calling
a sleeping function from atomic context:

  BUG: sleeping function called from invalid context at arch/arm64/mm/fault.c:313
  in_atomic(): 0, irqs_disabled(): 0, pid: 10290
  Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
  [...]
  [<ffffff8e016cd0cc>] ___might_sleep+0x134/0x144
  [<ffffff8e016cd158>] __might_sleep+0x7c/0x8c
  [<ffffff8e016977f0>] do_page_fault+0x140/0x330
  [<ffffff8e01681328>] do_mem_abort+0x54/0xb0
  Exception stack(0xfffffffb20247a70 to 0xfffffffb20247ba0)
  [...]
  [<ffffff8e016844fc>] el1_da+0x18/0x78
  [<ffffff8e017f399c>] path_parentat+0x44/0x88
  [<ffffff8e017f4c9c>] filename_parentat+0x5c/0xd8
  [<ffffff8e017f5044>] filename_create+0x4c/0x128
  [<ffffff8e017f59e4>] SyS_mkdirat+0x50/0xc8
  [<ffffff8e01684e30>] el0_svc_naked+0x24/0x28
  Code: 36380080 d5384100 f9400800 9402566d (d4210000)
  ---[ end trace 2d01889f2bca9b9f ]---

Fix this by dispatching all translation faults to do_translation_faults,
which avoids invoking the page fault logic for faults on kernel addresses.

Reported-by: Ankit Jain <ankijain@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Make sure SPsel is always set

commit 5371513fb338fb9989c569dc071326d369d6ade8 upstream.

When the kernel is entered at EL2 on an ARMv8.0 system, we construct
the EL1 pstate and make sure this uses the the EL1 stack pointer
(we perform an exception return to EL1h).

But if the kernel is either entered at EL1 or stays at EL2 (because
we're on a VHE-capable system), we fail to set SPsel, and use whatever
stack selection the higher exception level has choosen for us.

Let's not take any chance, and make sure that SPsel is set to one
before we decide the mode we're going to run in.

Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

seccomp: fix the usage of get/put_seccomp_filter() in seccomp_get_filter()

commit 66a733ea6b611aecf0119514d2dddab5f9d6c01e upstream.

As Chris explains, get_seccomp_filter() and put_seccomp_filter() can end
up using different filters. Once we drop ->siglock it is possible for
task->seccomp.filter to have been replaced by SECCOMP_FILTER_FLAG_TSYNC.

Fixes: f8e529ed941b ("seccomp, ptrace: add support for dumping seccomp filters")
Reported-by: Chris Salls <chrissalls5@gmail.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
[tycho: add __get_seccomp_filter vs. open coding refcount_inc()]
Signed-off-by: Tycho Andersen <tycho@docker.com>
[kees: tweak commit log]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bsg-lib: don't free job in bsg_prepare_job

commit f507b54dccfd8000c517d740bc45f20c74532d18 upstream.

The job structure is allocated as part of the request, so we should not
free it in the error path of bsg_prepare_job.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nl80211: check for the required netlink attributes presence

commit e785fa0a164aa11001cba931367c7f94ffaff888 upstream.

nl80211_set_rekey_data() does not check if the required attributes
NL80211_REKEY_DATA_{REPLAY_CTR,KEK,KCK} are present when processing
NL80211_CMD_SET_REKEY_OFFLOAD request. This request can be issued by
users with CAP_NET_ADMIN privilege and may result in NULL dereference
and a system crash. Add a check for the required attributes presence.
This patch is based on the patch by bo Zhang.

This fixes CVE-2017-12153.

References: https://bugzilla.redhat.com/show_bug.cgi?id=1491046
Fixes: e5497d766ad ("cfg80211/nl80211: support GTK rekey offload")
Reported-by: bo Zhang <zhangbo5891001@gmail.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfs: Return -ENXIO for negative SEEK_HOLE / SEEK_DATA offsets

commit fc46820b27a2d9a46f7e90c9ceb4a64a1bc5fab8 upstream.

In generic_file_llseek_size, return -ENXIO for negative offsets as well
as offsets beyond EOF. This affects filesystems which don't implement
SEEK_HOLE / SEEK_DATA internally, possibly because they don't support
holes.

Fixes xfstest generic/448.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags

commit 1013e760d10e614dc10b5624ce9fc41563ba2e65 upstream.

Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SMB: Validate negotiate (to protect against downgrade) even if signing off

commit 0603c96f3af50e2f9299fa410c224ab1d465e0f9 upstream.

As long as signing is supported (ie not a guest user connection) and
connection is SMB3 or SMB3.02, then validate negotiate (protect
against man in the middle downgrade attacks). We had been doing this
only when signing was required, not when signing was just enabled,
but this more closely matches recommended SMB3 behavior and is
better security. Suggested by Metze.

Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Jeremy Allison <jra@samba.org>
Acked-by: Stefan Metzmacher <metze@samba.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix SMB3.1.1 guest authentication to Samba

commit 23586b66d84ba3184b8820277f3fc42761640f87 upstream.

Samba rejects SMB3.1.1 dialect (vers=3.1.1) negotiate requests from
the kernel client due to the two byte pad at the end of the negotiate
contexts.

Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Fix parent_dn reference leak in add_dt_node()

commit b537ca6fede69a281dc524983e5e633d79a10a08 upstream.

A reference to the parent device node is held by add_dt_node() for the
node to be added. If the call to dlpar_configure_connector() fails
add_dt_node() returns ENOENT and that reference is not freed.

Add a call to of_node_put(parent_dn) prior to bailing out after a
failed dlpar_configure_connector() call.

Fixes: 8d5ff320766f ("powerpc/pseries: Make dlpar_configure_connector parent node aware")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KEYS: prevent KEYCTL_READ on negative key

commit 37863c43b2c6464f252862bf2e9768264e961678 upstream.

Because keyctl_read_key() looks up the key with no permissions
requested, it may find a negatively instantiated key.  If the key is
also possessed, we went ahead and called ->read() on the key.  But the
key payload will actually contain the ->reject_error rather than the
normal payload.  Thus, the kernel oopses trying to read the
user_key_payload from memory address (int)-ENOKEY = 0x00000000ffffff82.

Fortunately the payload data is stored inline, so it shouldn't be
possible to abuse this as an arbitrary memory read primitive...

Reproducer:
    keyctl new_session
    keyctl request2 user desc '' @s
    keyctl read $(keyctl show | awk '/user: desc/ {print $1}')

It causes a crash like the following:
     BUG: unable to handle kernel paging request at 00000000ffffff92
     IP: user_read+0x33/0xa0
     PGD 36a54067 P4D 36a54067 PUD 0
     Oops: 0000 [#1] SMP
     CPU: 0 PID: 211 Comm: keyctl Not tainted 4.14.0-rc1 #337
     Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-20170228_101828-anatol 04/01/2014
     task: ffff90aa3b74c3c0 task.stack: ffff9878c0478000
     RIP: 0010:user_read+0x33/0xa0
     RSP: 0018:ffff9878c047bee8 EFLAGS: 00010246
     RAX: 0000000000000001 RBX: ffff90aa3d7da340 RCX: 0000000000000017
     RDX: 0000000000000000 RSI: 00000000ffffff82 RDI: ffff90aa3d7da340
     RBP: ffff9878c047bf00 R08: 00000024f95da94f R09: 0000000000000000
     R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
     R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
     FS:  00007f58ece69740(0000) GS:ffff90aa3e200000(0000) knlGS:0000000000000000
     CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
     CR2: 00000000ffffff92 CR3: 0000000036adc001 CR4: 00000000003606f0
     Call Trace:
      keyctl_read_key+0xac/0xe0
      SyS_keyctl+0x99/0x120
      entry_SYSCALL_64_fastpath+0x1f/0xbe
     RIP: 0033:0x7f58ec787bb9
     RSP: 002b:00007ffc8d401678 EFLAGS: 00000206 ORIG_RAX: 00000000000000fa
     RAX: ffffffffffffffda RBX: 00007ffc8d402800 RCX: 00007f58ec787bb9
     RDX: 0000000000000000 RSI: 00000000174a63ac RDI: 000000000000000b
     RBP: 0000000000000004 R08: 00007ffc8d402809 R09: 0000000000000020
     R10: 0000000000000000 R11: 0000000000000206 R12: 00007ffc8d402800
     R13: 00007ffc8d4016e0 R14: 0000000000000000 R15: 0000000000000000
     Code: e5 41 55 49 89 f5 41 54 49 89 d4 53 48 89 fb e8 a4 b4 ad ff 85 c0 74 09 80 3d b9 4c 96 00 00 74 43 48 8b b3 20 01 00 00 4d 85 ed <0f> b7 5e 10 74 29 4d 85 e4 74 24 4c 39 e3 4c 89 e2 4c 89 ef 48
     RIP: user_read+0x33/0xa0 RSP: ffff9878c047bee8
     CR2: 00000000ffffff92

Fixes: 61ea0c0ba904 ("KEYS: Skip key state checks when checking for possession")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KEYS: prevent creating a different user's keyrings

commit 237bbd29f7a049d310d907f4b2716a7feef9abf3 upstream.

It was possible for an unprivileged user to create the user and user
session keyrings for another user.  For example:

    sudo -u '#3000' sh -c 'keyctl add keyring _uid.4000 "" @u
                           keyctl add keyring _uid_ses.4000 "" @u
                           sleep 15' &
    sleep 1
    sudo -u '#4000' keyctl describe @u
    sudo -u '#4000' keyctl describe @us

This is problematic because these "fake" keyrings won't have the right
permissions.  In particular, the user who created them first will own
them and will have full access to them via the possessor permissions,
which can be used to compromise the security of a user's keys:

    -4: alswrv-----v------------  3000     0 keyring: _uid.4000
    -5: alswrv-----v------------  3000     0 keyring: _uid_ses.4000

Fix it by marking user and user session keyrings with a flag
KEY_FLAG_UID_KEYRING.  Then, when searching for a user or user session
keyring by name, skip all keyrings that don't have the flag set.

Fixes: 69664cf16af4 ("keys: don't generate user and user session keyrings unless they're accessed")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KEYS: fix writing past end of user-supplied buffer in keyring_read()

commit e645016abc803dafc75e4b8f6e4118f088900ffb upstream.

Userspace can call keyctl_read() on a keyring to get the list of IDs of
keys in the keyring. But if the user-supplied buffer is too small, the
kernel would write the full list anyway --- which will corrupt whatever
userspace memory happened to be past the end of the buffer. Fix it by
only filling the space that is available.

Fixes: b2a4df200d57 ("KEYS: Expand the capacity of a keyring")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: talitos - fix sha224

commit afd62fa26343be6445479e75de9f07092a061459 upstream.

Kernel crypto tests report the following error at startup

[ 2.752626] alg: hash: Test 4 failed for sha224-talitos
[ 2.757907] 00000000: 30 e2 86 e2 e7 8a dd 0d d7 eb 9f d5 83 fe f1 b0
00000010: 2d 5a 6c a5 f9 55 ea fd 0e 72 05 22

This patch fixes it

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: talitos - Don't provide setkey for non hmac hashing algs.

commit 56136631573baa537a15e0012055ffe8cfec1a33 upstream.

Today, md5sum fails with error -ENOKEY because a setkey
function is set for non hmac hashing algs, see strace output below:

mmap(NULL, 378880, PROT_READ, MAP_SHARED, 6, 0) = 0x77f50000
accept(3, 0, NULL) = 7
vmsplice(5, [{"bin/\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 378880}], 1, SPLICE_F_MORE|SPLICE_F_GIFT) = 262144
splice(4, NULL, 7, NULL, 262144, SPLICE_F_MORE) = -1 ENOKEY (Required key not available)
write(2, "Generation of hash for file kcap"..., 50) = 50
munmap(0x77f50000, 378880) = 0

This patch ensures that setkey() function is set only
for hmac hashing.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: scsi_transport_iscsi: fix the issue that iscsi_if_rx doesn't parse nlmsg properly

commit c88f0e6b06f4092995688211a631bb436125d77b upstream.

ChunYu found a kernel crash by syzkaller:

[  651.617875] kasan: CONFIG_KASAN_INLINE enabled
[  651.618217] kasan: GPF could be caused by NULL-ptr deref or user memory access
[  651.618731] general protection fault: 0000 [#1] SMP KASAN
[  651.621543] CPU: 1 PID: 9539 Comm: scsi Not tainted 4.11.0.cov #32
[  651.621938] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[  651.622309] task: ffff880117780000 task.stack: ffff8800a3188000
[  651.622762] RIP: 0010:skb_release_data+0x26c/0x590
[...]
[  651.627260] Call Trace:
[  651.629156]  skb_release_all+0x4f/0x60
[  651.629450]  consume_skb+0x1a5/0x600
[  651.630705]  netlink_unicast+0x505/0x720
[  651.632345]  netlink_sendmsg+0xab2/0xe70
[  651.633704]  sock_sendmsg+0xcf/0x110
[  651.633942]  ___sys_sendmsg+0x833/0x980
[  651.637117]  __sys_sendmsg+0xf3/0x240
[  651.638820]  SyS_sendmsg+0x32/0x50
[  651.639048]  entry_SYSCALL_64_fastpath+0x1f/0xc2

It's caused by skb_shared_info at the end of sk_buff was overwritten by
ISCSI_KEVENT_IF_ERROR when parsing nlmsg info from skb in iscsi_if_rx.

During the loop if skb->len == nlh->nlmsg_len and both are sizeof(*nlh),
ev = nlmsg_data(nlh) will acutally get skb_shinfo(SKB) instead and set a
new value to skb_shinfo(SKB)->nr_frags by ev->type.

This patch is to fix it by checking nlh->nlmsg_len properly there to
avoid over accessing sk_buff.

Reported-by: ChunYu Wang <chunwang@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid5: preserve STRIPE_ON_UNPLUG_LIST in break_stripe_batch_list

commit 184a09eb9a2fe425e49c9538f1604b05ed33cfef upstream.

In release_stripe_plug(), if a stripe_head has its STRIPE_ON_UNPLUG_LIST
set, it indicates that this stripe_head is already in the raid5_plug_cb
list and release_stripe() would be called instead to drop a reference
count. Otherwise, the STRIPE_ON_UNPLUG_LIST bit would be set for this
stripe_head and it will get queued into the raid5_plug_cb list.

Since break_stripe_batch_list() did not preserve STRIPE_ON_UNPLUG_LIST,
A stripe could be re-added to plug list while it is still on that list
in the following situation. If stripe_head A is added to another
stripe_head B's batch list, in this case A will have its
batch_head != NULL and be added into the plug list. After that,
stripe_head B gets handled and called break_stripe_batch_list() to
reset all the batched stripe_head(including A which is still on
the plug list)'s state and reset their batch_head to NULL.
Before the plug list gets processed, if there is another write request
comes in and get stripe_head A, A will have its batch_head == NULL
(cleared by calling break_stripe_batch_list() on B) and be added to
plug list once again.

Signed-off-by: Dennis Yang <dennisyang@qnap.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid5: fix a race condition in stripe batch

commit 3664847d95e60a9a943858b7800f8484669740fc upstream.

We have a race condition in below scenario, say have 3 continuous stripes, sh1,
sh2 and sh3, sh1 is the stripe_head of sh2 and sh3:

CPU1 CPU2 CPU3
handle_stripe(sh3)
stripe_add_to_batch_list(sh3)
-> lock(sh2, sh3)
-> lock batch_lock(sh1)
-> add sh3 to batch_list of sh1
-> unlock batch_lock(sh1)
clear_batch_ready(sh1)
-> lock(sh1) and batch_lock(sh1)
-> clear STRIPE_BATCH_READY for all stripes in batch_list
-> unlock(sh1) and batch_lock(sh1)
->clear_batch_ready(sh3)
-->test_and_clear_bit(STRIPE_BATCH_READY, sh3)
--->return 0 as sh->batch == NULL
-> sh3->batch_head = sh1
-> unlock (sh2, sh3)

In CPU1, handle_stripe will continue handle sh3 even it's in batch stripe list
of sh1. By moving sh3->batch_head assignment in to batch_lock, we make it
impossible to clear STRIPE_BATCH_READY before batch_head is set.

Thanks Stephane for helping debug this tricky issue.

Reported-and-tested-by: Stephane Thiell <sthiell@stanford.edu>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Erase irqsoff trace with empty write

commit 8dd33bcb7050dd6f8c1432732f930932c9d3a33e upstream.

One convenient way to erase trace is "echo > trace". However, this
is currently broken if the current tracer is irqsoff tracer. This
is because irqsoff tracer use max_buffer as the default trace
buffer.

Set the max_buffer as the one to be cleared when it's the trace
buffer currently in use.

Link: http://lkml.kernel.org/r/1505754215-29411-1-git-send-email-byan@nvidia.com
Cc: <mingo@redhat.com>
Fixes: 4acd4d00f ("tracing: give easy way to clear trace buffer")
Signed-off-by: Bo Yan <byan@nvidia.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Fix trace_pipe behavior for instance traces

commit 75df6e688ccd517e339a7c422ef7ad73045b18a2 upstream.

When reading data from trace_pipe, tracing_wait_pipe() performs a
check to see if tracing has been turned off after some data was read.
Currently, this check always looks at global trace state, but it
should be checking the trace instance where trace_pipe is located at.

Because of this bug, cat instances/i1/trace_pipe in the following
script will immediately exit instead of waiting for data:

cd /sys/kernel/debug/tracing
echo 0 > tracing_on
mkdir -p instances/i1
echo 1 > instances/i1/tracing_on
echo 1 > instances/i1/events/sched/sched_process_exec/enable
cat instances/i1/trace_pipe

Link: http://lkml.kernel.org/r/20170917102348.1615-1-tahsin@google.com
Fixes: 10246fa35d4f ("tracing: give easy way to clear trace buffer")
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book3S: Fix race and leak in kvm_vm_ioctl_create_spapr_tce()

commit 47c5310a8dbe7c2cb9f0083daa43ceed76c257fa upstream, with part
of commit edd03602d97236e8fea13cd76886c576186aa307 folded in.

Nixiaoming pointed out that there is a memory leak in
kvm_vm_ioctl_create_spapr_tce() if the call to anon_inode_getfd()
fails; the memory allocated for the kvmppc_spapr_tce_table struct
is not freed, and nor are the pages allocated for the iommu
tables.

David Hildenbrand pointed out that there is a race in that the
function checks early on that there is not already an entry in the
stt->iommu_tables list with the same LIOBN, but an entry with the
same LIOBN could get added between then and when the new entry is
added to the list.

This fixes both problems. To simplify things, we now call
anon_inode_getfd() before placing the new entry in the list. The
check for an existing entry is done while holding the kvm->lock
mutex, immediately before adding the new entry to the list.

[paulus@ozlabs.org - folded in that part of edd03602d972 ("KVM:
PPC: Book3S HV: Protect updates to spapr_tce_tables list", 2017-08-28)
which restructured the code that 47c5310a8dbe modified, to avoid
a build failure caused by the absence of put_unused_fd().
Also removed the locked memory accounting, since it doesn't exist
in this version, and adjusted the commit message.]

Fixes: 54738c097163 ("KVM: PPC: Accelerate H_PUT_TCE by implementing it in real mode")
Reported-by: Nixiaoming <nixiaoming@huawei.com>
Reported-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: flush hw_roc_start work before cancelling the ROC

commit 6e46d8ce894374fc135c96a8d1057c6af1fef237 upstream.

When HW ROC is supported it is possible that after the HW notified
that the ROC has started, the ROC was cancelled and another ROC was
added while the hw_roc_start worker is waiting on the mutex (since
cancelling the ROC and adding another one also holds the same mutex).
As a result, the hw_roc_start worker will continue to run after the
new ROC is added but before it is actually started by the HW.
This may result in notifying userspace that the ROC has started before
it actually does, or in case of management tx ROC, in an attempt to
tx while not on the right channel.

In addition, when the driver will notify mac80211 that the second ROC
has started, mac80211 will warn that this ROC has already been
notified.

Fix this by flushing the hw_roc_start work before cancelling an ROC.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: release auth_key.response for reconnect.

commit f5c4ba816315d3b813af16f5571f86c8d4e897bd upstream.

There is a race that cause cifs reconnect in cifs_mount,
- cifs_mount
  - cifs_get_tcp_session
    - [ start thread cifs_demultiplex_thread
      - cifs_read_from_socket: -ECONNABORTED
        - DELAY_WORK smb2_reconnect_server ]
  - cifs_setup_session
  - [ smb2_reconnect_server ]

auth_key.response was allocated in cifs_setup_session, and
will release when the session destoried. So when session re-
connect, auth_key.response should be check and released.

Tested with my system:
CIFS VFS: Free previous auth_key.response = ffff8800320bbf80

A simple auth_key.response allocation call trace:
- cifs_setup_session
- SMB2_sess_setup
- SMB2_sess_auth_rawntlmssp_authenticate
- build_ntlmssp_auth_blob
- setup_ntlmv2_rsp

Signed-off-by: Shu Wang <shuwang@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.89

ftrace: Fix memleak when unregistering dynamic ops when tracing disabled

commit edb096e00724f02db5f6ec7900f3bbd465c6c76f upstream.

If function tracing is disabled by the user via the function-trace option or
the proc sysctl file, and a ftrace_ops that was allocated on the heap is
unregistered, then the shutdown code exits out without doing the proper
clean up. This was found via kmemleak and running the ftrace selftests, as
one of the tests unregisters with function tracing disabled.

# cat kmemleak
unreferenced object 0xffffffffa0020000 (size 4096):
  comm "swapper/0", pid 1, jiffies 4294668889 (age 569.209s)
  hex dump (first 32 bytes):
    55 ff 74 24 10 55 48 89 e5 ff 74 24 18 55 48 89  U.t$.UH...t$.UH.
    e5 48 81 ec a8 00 00 00 48 89 44 24 50 48 89 4c  .H......H.D$PH.L
  backtrace:
    [<ffffffff81d64665>] kmemleak_vmalloc+0x85/0xf0
    [<ffffffff81355631>] __vmalloc_node_range+0x281/0x3e0
    [<ffffffff8109697f>] module_alloc+0x4f/0x90
    [<ffffffff81091170>] arch_ftrace_update_trampoline+0x160/0x420
    [<ffffffff81249947>] ftrace_startup+0xe7/0x300
    [<ffffffff81249bd2>] register_ftrace_function+0x72/0x90
    [<ffffffff81263786>] trace_selftest_ops+0x204/0x397
    [<ffffffff82bb8971>] trace_selftest_startup_function+0x394/0x624
    [<ffffffff81263a75>] run_tracer_selftest+0x15c/0x1d7
    [<ffffffff82bb83f1>] init_trace_selftests+0x75/0x192
    [<ffffffff81002230>] do_one_initcall+0x90/0x1e2
    [<ffffffff82b7d620>] kernel_init_freeable+0x350/0x3fe
    [<ffffffff81d61ec3>] kernel_init+0x13/0x122
    [<ffffffff81d72c6a>] ret_from_fork+0x2a/0x40
    [<ffffffffffffffff>] 0xffffffffffffffff

Fixes: 12cce594fa ("ftrace/x86: Allow !CONFIG_PREEMPT dynamic ops to use allocated trampolines")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: fix bch_hprint crash and improve output

commit 9276717b9e297a62d1151a43d1cd286213f68eb7 upstream.

Most importantly, solve a crash where %llu was used to format signed
numbers.  This would cause a buffer overflow when reading sysfs
writeback_rate_debug, as only 20 bytes were allocated for this and
%llu writes 20 characters plus a null.

Always use the units mechanism rather than having different output
paths for simplicity.

Also, correct problems with display output where 1.10 was a larger
number than 1.09, by multiplying by 10 and then dividing by 1024 instead
of dividing by 100.  (Remainders of >= 1000 would print as .10).

Minor changes: Always display the decimal point instead of trying to
omit it based on number of digits shown.  Decide what units to use
based on 1000 as a threshold, not 1024 (in other words, always print
at most 3 digits before the decimal point).

Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reported-by: Dmitry Yu Okunev <dyokunev@ut.mephi.ru>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: Correct return value for sysfs attach errors

commit 77fa100f27475d08a569b9d51c17722130f089e7 upstream.

If you encounter any errors in bch_cached_dev_attach it will return
a negative error code. The variable 'v' which stores the result is
unsigned, thus user space sees a very large value returned for bytes
written which can cause incorrect user space behavior. Utilize 1
signed variable to use throughout the function to preserve error return
capability.

Signed-off-by: Tony Asleson <tasleson@redhat.com>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: correct cache_dirty_target in __update_writeback_rate()

commit a8394090a9129b40f9d90dcb7f4a49d60c727ca6 upstream.

__update_write_rate() uses a Proportion-Differentiation Controller
algorithm to control writeback rate. A dirty target number is used in
this PD controller to control writeback rate. A larger target number
will make the writeback rate smaller, on the versus, a smaller target
number will make the writeback rate larger.

bcache uses the following steps to calculate the target number,
1) cache_sectors = all-buckets-of-cache-set * buckets-size
2) cache_dirty_target = cache_sectors * cached-device-writeback_percent
3) target = cache_dirty_target *
(sectors-of-cached-device/sectors-of-all-cached-devices-of-this-cache-set)

The calculation at step 1) for cache_sectors is incorrect, which does
not consider dirty blocks occupied by flash only volume.

A flash only volume can be took as a bcache device without cached
device. All data sectors allocated for it are persistent on cache device
and marked dirty, they are not touched by bcache writeback and garbage
collection code. So data blocks of flash only volume should be ignore
when calculating cache_sectors of cache set.

Current code does not subtract dirty sectors of flash only volume, which
results a larger target number from the above 3 steps. And in sequence
the cache device's writeback rate is smaller then a correct value,
writeback speed is slower on all cached devices.

This patch fixes the incorrect slower writeback rate by subtracting
dirty sectors of flash only volumes in __update_writeback_rate().

(Commit log composed by Coly Li to pass checkpatch.pl checking)

Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: do not subtract sectors_to_gc for bypassed IO

commit 69daf03adef5f7bc13e0ac86b4b8007df1767aab upstream.

Since bypassed IOs use no bucket, so do not subtract sectors_to_gc to
trigger gc thread.

Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Acked-by: Coly Li <colyli@suse.de>
Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: Fix leak of bdev reference

commit 4b758df21ee7081ab41448d21d60367efaa625b3 upstream.

If blkdev_get_by_path() in register_bcache() fails, we try to lookup the
block device using lookup_bdev() to detect which situation we are in to
properly report error. However we never drop the reference returned to
us from lookup_bdev(). Fix that.

Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: initialize dirty stripes in flash_dev_run()

commit 175206cf9ab63161dec74d9cd7f9992e062491f5 upstream.

bcache uses a Proportion-Differentiation Controller algorithm to control
writeback rate to cached devices. In the PD controller algorithm, dirty
stripes of thin flash device should not be counted in, because flash only
volumes never write back dirty data.

Currently dirty stripe counter for thin flash device is not initialized
when the thin flash device starts. Which means the following calculation
in PD controller will reference an undefined dirty stripes number, and
all cached devices attached to the same cache set where the thin flash
device lies on may have an inaccurate writeback rate.

This patch calles bch_sectors_dirty_init() in flash_dev_run(), to
correctly initialize dirty stripe counter when the thin flash device
starts to run. This patch also does following parameter data type change,
-void bch_sectors_dirty_init(struct cached_dev *dc);
+void bch_sectors_dirty_init(struct bcache_device *);
to call this function conveniently in flash_dev_run().

(Commit log is composed by Coly Li)

Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: uvcvideo: Prevent heap overflow when accessing mapped controls

commit 7e09f7d5c790278ab98e5f2c22307ebe8ad6e8ba upstream.

The size of uvc_control_mapping is user controlled leading to a
potential heap overflow in the uvc driver. This adds a check to verify
the user provided size fits within the bounds of the defined buffer
size.

Originally-from: Richard Simmons <rssimmo@amazon.com>

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: v4l2-compat-ioctl32: Fix timespec conversion

commit 9c7ba1d7634cef490b85bc64c4091ff004821bfd upstream.

Certain syscalls like recvmmsg support 64 bit timespec values for the
X32 ABI. The helper function compat_put_timespec converts a timespec
value to a 32 bit or 64 bit value depending on what ABI is used. The
v4l2 compat layer, however, is not designed to support 64 bit timespec
values and always uses 32 bit values. Hence, compat_put_timespec must
not be used.

Without this patch, user space will be provided with bad timestamp
values from the VIDIOC_DQEVENT ioctl. Also, fields of the struct
v4l2_event32 that come immediately after timestamp get overwritten,
namely the field named id.

Fixes: 81993e81a994 ("compat: Get rid of (get|put)_compat_time(val|spec)")
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Tiffany Lin <tiffany.lin@mediatek.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: shpchp: Enable bridge bus mastering if MSI is enabled

commit 48b79a14505349a29b3e20f03619ada9b33c4b17 upstream.

An SHPC may generate MSIs to notify software about slot or controller
events (SHPC spec r1.0, sec 4.7). A PCI device can only generate an MSI if
it has bus mastering enabled.

Enable bus mastering if the bridge contains an SHPC that uses MSI for event
notifications.

Signed-off-by: Aleksandr Bezzubikov <zuban32s@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: Re-enable MMU upon Machine Check exception

commit 1ee55a8f7f6b7ca4c0c59e0b4b4e3584a085c2d3 upstream.

I recently came upon a scenario where I would get a double fault
machine check exception tiriggered by a kernel module.
However the ensuing crash stacktrace (ksym lookup) was not working
correctly.

Turns out that machine check auto-disables MMU while modules are allocated
in kernel vaddr spapce.

This patch re-enables the MMU before start printing the stacktrace
making stacktracing of modules work upon a fatal exception.

Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: moved code into low level handler to avoid in 2 places]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Apply trace_clock changes to instance max buffer

commit 170b3b1050e28d1ba0700e262f0899ffa4fccc52 upstream.

Currently trace_clock timestamps are applied to both regular and max
buffers only for global trace. For instance trace, trace_clock
timestamps are applied only to regular buffer. But, regular and max
buffers can be swapped, for example, following a snapshot. So, for
instance trace, bad timestamps can be seen following a snapshot.
Let's apply trace_clock timestamps to instance max buffer as well.

Link: http://lkml.kernel.org/r/ebdb168d0be042dcdf51f81e696b17fabe3609c1.1504642143.git.tom.zanussi@linux.intel.com
Fixes: 277ba0446 ("tracing: Add interface to allow multiple trace buffers")
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ftrace: Fix selftest goto location on error

commit 46320a6acc4fb58f04bcf78c4c942cc43b20f986 upstream.

In the second iteration of trace_selftest_ops(), the error goto label is
wrong in the case where trace_selftest_test_global_cnt is off. In the
case of error, it leaks the dynamic ops that was allocated.

Fixes: 95950c2e ("ftrace: Add self-tests for multiple function trace users")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: qla2xxx: Fix an integer overflow in sysfs code

commit e6f77540c067b48dee10f1e33678415bfcc89017 upstream.

The value of "size" comes from the user.  When we add "start + size" it
could lead to an integer overflow bug.

It means we vmalloc() a lot more memory than we had intended.  I believe
that on 64 bit systems vmalloc() can succeed even if we ask it to
allocate huge 4GB buffers.  So we would get memory corruption and likely
a crash when we call ha->isp_ops->write_optrom() and ->read_optrom().

Only root can trigger this bug.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=194061
Fixes: b7cc176c9eb3 ("[SCSI] qla2xxx: Allow region-based flash-part accesses.")
Reported-by: shqking <shqking@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: sg: fixup infoleak when using SG_GET_REQUEST_TABLE

commit 3e0097499839e0fe3af380410eababe5a47c4cf9 upstream.

When calling SG_GET_REQUEST_TABLE ioctl only a half-filled table is
returned; the remaining part will then contain stale kernel memory
information. This patch zeroes out the entire table to avoid this
issue.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: sg: factor out sg_fill_request_table()

commit 4759df905a474d245752c9dc94288e779b8734dd upstream.

Factor out sg_fill_request_table() for better readability.

[mkp: typos, applied by hand]

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: sg: off by one in sg_ioctl()

commit bd46fc406b30d1db1aff8dabaff8d18bb423fdcf upstream.

If "val" is SG_MAX_QUEUE then we are one element beyond the end of the
"rinfo" array so the > should be >=.

Fixes: 109bade9c625 ("scsi: sg: use standard lists for sg_requests")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: sg: use standard lists for sg_requests

commit 109bade9c625c89bb5ea753aaa1a0a97e6fbb548 upstream.

'Sg_request' is using a private list implementation; convert it to
standard lists.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: sg: remove 'save_scat_len'

commit 136e57bf43dc4babbfb8783abbf707d483cacbe3 upstream.

Unused.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: storvsc: fix memory leak on ring buffer busy

commit 0208eeaa650c5c866a3242201678a19e6dc4a14e upstream.

When storvsc is sending I/O to Hyper-v, it may allocate a bigger buffer
descriptor for large data payload that can't fit into a pre-allocated
buffer descriptor. This bigger buffer is freed on return path.

If I/O request to Hyper-v fails due to ring buffer busy, the storvsc
allocated buffer descriptor should also be freed.

[mkp: applied by hand]

Fixes: be0cf6ca301c ("scsi: storvsc: Set the tablesize based on the information given by the host")
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: megaraid_sas: Return pended IOCTLs with cmd_status MFI_STAT_WRONG_STATE in case adapter is dead

commit eb3fe263a48b0d27b229c213929c4cb3b1b39a0f upstream.

After a kill adapter, since the cmd_status is not set, the IOCTLs will
be hung in driver resulting in application hang. Set cmd_status
MFI_STAT_WRONG_STATE when completing pended IOCTLs.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: megaraid_sas: Check valid aen class range to avoid kernel panic

commit 91b3d9f0069c8307d0b3a4c6843b65a439183318 upstream.

Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: trace high part of "new" 64 bit SCSI LUN

commit 5d4a3d0a2ff23799b956e5962b886287614e7fad upstream.

Complements debugging aspects of the otherwise functionally complete
v3.17 commit 9cb78c16f5da ("scsi: use 64-bit LUNs").

While I don't have access to a target exporting 3 or 4 level LUNs,
I did test it by explicitly attaching a non-existent fake 4 level LUN
by means of zfcp sysfs attribute "unit_add".
In order to see corresponding trace records of otherwise successful
events, we had to increase the trace level of area SCSI and HBA to 6.

$ echo 6 > /sys/kernel/debug/s390dbf/zfcp_0.0.1880_scsi/level
$ echo 6 > /sys/kernel/debug/s390dbf/zfcp_0.0.1880_hba/level

$ echo 0x4011402240334044 > \
  /sys/bus/ccw/drivers/zfcp/0.0.1880/0x50050763031bd327/unit_add

Example output formatted by an updated zfcpdbf from the s390-tools
package interspersed with kernel messages at scsi_logging_level=4605:

Timestamp      : ...
Area           : REC
Subarea        : 00
Level          : 1
Exception      : -
CPU ID         : ..
Caller         : 0x...
Record ID      : 1
Tag            : scsla_1
LUN            : 0x4011402240334044
WWPN           : 0x50050763031bd327
D_ID           : 0x00......
Adapter status : 0x5400050b
Port status    : 0x54000001
LUN status     : 0x41000000
Ready count    : 0x00000001
Running count  : 0x00000000
ERP want       : 0x01
ERP need       : 0x01

scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY pass 1 length 36
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY successful with code 0x0

Timestamp      : ...
Area           : HBA
Subarea        : 00
Level          : 6
Exception      : -
CPU ID         : ..
Caller         : 0x...
Record ID      : 1
Tag            : fs_norm
Request ID     : 0x<inquiry2-req-id>
Request status : 0x00000010
FSF cmnd       : 0x00000001
FSF sequence no: 0x...
FSF issued     : ...
FSF stat       : 0x00000000
FSF stat qual  : 00000000 00000000 00000000 00000000
Prot stat      : 0x00000001
Prot stat qual : ........ ........ 00000000 00000000
Port handle    : 0x...
LUN handle     : 0x...
|
Timestamp      : ...
Area           : SCSI
Subarea        : 00
Level          : 6
Exception      : -
CPU ID         : ..
Caller         : 0x...
Record ID      : 1
Tag            : rsl_nor
Request ID     : 0x<inquiry2-req-id>
SCSI ID        : 0x00000000
SCSI LUN       : 0x40224011
SCSI LUN high  : 0x40444033 <=======================
SCSI result    : 0x00000000
SCSI retries   : 0x00
SCSI allowed   : 0x03
SCSI scribble  : 0x<inquiry2-req-id>
SCSI opcode    : 12000000 a4000000 00000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU     : 00000000 00000000 00000000 00000000
                 00000000 00000000

scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY pass 2 length 164
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY successful with code 0x0
scsi 2:0:0:4630896905707208721: scsi scan: peripheral device type of 31, \
no device added

Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 9cb78c16f5da ("scsi: use 64-bit LUNs")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: trace HBA FSF response by default on dismiss or timedout late response

commit fdb7cee3b9e3c561502e58137a837341f10cbf8b upstream.

At the default trace level, we only trace unsuccessful events including
FSF responses.

zfcp_dbf_hba_fsf_response() only used protocol status and FSF status to
decide on an unsuccessful response. However, this is only one of multiple
possible sources determining a failed struct zfcp_fsf_req.

An FSF request can also "fail" if its response runs into an ERP timeout
or if it gets dismissed because a higher level recovery was triggered
[trace tags "erscf_1" or "erscf_2" in zfcp_erp_strategy_check_fsfreq()].
FSF requests with ERP timeout are:
FSF_QTCB_EXCHANGE_CONFIG_DATA, FSF_QTCB_EXCHANGE_PORT_DATA,
FSF_QTCB_OPEN_PORT_WITH_DID or FSF_QTCB_CLOSE_PORT or
FSF_QTCB_CLOSE_PHYSICAL_PORT for target ports,
FSF_QTCB_OPEN_LUN, FSF_QTCB_CLOSE_LUN.
One example is slow queue processing which can cause follow-on errors,
e.g. FSF_PORT_ALREADY_OPEN after FSF_QTCB_OPEN_PORT_WITH_DID timed out.
In order to see the root cause, we need to see late responses even if the
channel presented them successfully with FSF_PROT_GOOD and FSF_GOOD.
Example trace records formatted with zfcpdbf from the s390-tools package:

Timestamp      : ...
Area           : REC
Subarea        : 00
Level          : 1
Exception      : -
CPU ID         : ..
Caller         : ...
Record ID      : 1
Tag            : fcegpf1
LUN            : 0xffffffffffffffff
WWPN           : 0x<WWPN>
D_ID           : 0x00<D_ID>
Adapter status : 0x5400050b
Port status    : 0x41200000
LUN status     : 0x00000000
Ready count    : 0x00000001
Running count  : 0x...
ERP want       : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT
ERP need       : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT
|
Timestamp      : ... 30 seconds later
Area           : REC
Subarea        : 00
Level          : 1
Exception      : -
CPU ID         : ..
Caller         : ...
Record ID      : 2
Tag            : erscf_2
LUN            : 0xffffffffffffffff
WWPN           : 0x<WWPN>
D_ID           : 0x00<D_ID>
Adapter status : 0x5400050b
Port status    : 0x41200000
LUN status     : 0x00000000
Request ID     : 0x<request_ID>
ERP status     : 0x10000000 ZFCP_STATUS_ERP_TIMEDOUT
ERP step       : 0x0800 ZFCP_ERP_STEP_PORT_OPENING
ERP action     : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT
ERP count      : 0x00
|
Timestamp      : ... later than previous record
Area           : HBA
Subarea        : 00
Level          : 5 > default level => 3 <= default level
Exception      : -
CPU ID         : 00
Caller         : ...
Record ID      : 1
Tag            : fs_qtcb => fs_rerr
Request ID     : 0x<request_ID>
Request status : 0x00001010 ZFCP_STATUS_FSFREQ_DISMISSED
| ZFCP_STATUS_FSFREQ_CLEANUP
FSF cmnd       : 0x00000005
FSF sequence no: 0x...
FSF issued     : ... > 30 seconds ago
FSF stat       : 0x00000000 FSF_GOOD
FSF stat qual  : 00000000 00000000 00000000 00000000
Prot stat      : 0x00000001 FSF_PROT_GOOD
Prot stat qual : 00000000 00000000 00000000 00000000
Port handle    : 0x...
LUN handle     : 0x00000000
QTCB log length: ...
QTCB log info  : ...

In case of problems detecting that new responses are waiting on the input
queue, we sooner or later trigger adapter recovery due to an FSF request
timeout (trace tag "fsrth_1").
FSF requests with FSF request timeout are:
typically FSF_QTCB_ABORT_FCP_CMND; but theoretically also
FSF_QTCB_EXCHANGE_CONFIG_DATA or FSF_QTCB_EXCHANGE_PORT_DATA via sysfs,
FSF_QTCB_OPEN_PORT_WITH_DID or FSF_QTCB_CLOSE_PORT for WKA ports,
FSF_QTCB_FCP_CMND for task management function (LUN / target reset).
One or more pending requests can meanwhile have FSF_PROT_GOOD and FSF_GOOD
because the channel filled in the response via DMA into the request's QTCB.

In a theroretical case, inject code can create an erroneous FSF request
on purpose. If data router is enabled, it uses deferred error reporting.
A READ SCSI command can succeed with FSF_PROT_GOOD, FSF_GOOD, and
SAM_STAT_GOOD. But on writing the read data to host memory via DMA,
it can still fail, e.g. if an intentionally wrong scatter list does not
provide enough space. Rather than getting an unsuccessful response,
we get a QDIO activate check which in turn triggers adapter recovery.
One or more pending requests can meanwhile have FSF_PROT_GOOD and FSF_GOOD
because the channel filled in the response via DMA into the request's QTCB.
Example trace records formatted with zfcpdbf from the s390-tools package:

Timestamp      : ...
Area           : HBA
Subarea        : 00
Level          : 6 > default level => 3 <= default level
Exception      : -
CPU ID         : ..
Caller         : ...
Record ID      : 1
Tag            : fs_norm => fs_rerr
Request ID     : 0x<request_ID2>
Request status : 0x00001010 ZFCP_STATUS_FSFREQ_DISMISSED
| ZFCP_STATUS_FSFREQ_CLEANUP
FSF cmnd       : 0x00000001
FSF sequence no: 0x...
FSF issued     : ...
FSF stat       : 0x00000000 FSF_GOOD
FSF stat qual  : 00000000 00000000 00000000 00000000
Prot stat      : 0x00000001 FSF_PROT_GOOD
Prot stat qual : ........ ........ 00000000 00000000
Port handle    : 0x...
LUN handle     : 0x...
|
Timestamp      : ...
Area           : SCSI
Subarea        : 00
Level          : 3
Exception      : -
CPU ID         : ..
Caller         : ...
Record ID      : 1
Tag            : rsl_err
Request ID     : 0x<request_ID2>
SCSI ID        : 0x...
SCSI LUN       : 0x...
SCSI result    : 0x000e0000 DID_TRANSPORT_DISRUPTED
SCSI retries   : 0x00
SCSI allowed   : 0x05
SCSI scribble  : 0x<request_ID2>
SCSI opcode    : 28... Read(10)
FCP rsp inf cod: 0x00
FCP rsp IU     : 00000000 00000000 00000000 00000000
                                         ^^ SAM_STAT_GOOD
                 00000000 00000000

Only with luck in both above cases, we could see a follow-on trace record
of an unsuccesful event following a successful but late FSF response with
FSF_PROT_GOOD and FSF_GOOD. Typically this was the case for I/O requests
resulting in a SCSI trace record "rsl_err" with DID_TRANSPORT_DISRUPTED
[On ZFCP_STATUS_FSFREQ_DISMISSED, zfcp_fsf_protstatus_eval() sets
ZFCP_STATUS_FSFREQ_ERROR seen by the request handler functions as failure].
However, the reason for this follow-on trace was invisible because the
corresponding HBA trace record was missing at the default trace level
(by default hidden records with tags "fs_norm", "fs_qtcb", or "fs_open").

On adapter recovery, after we had shut down the QDIO queues, we perform
unsuccessful pseudo completions with flag ZFCP_STATUS_FSFREQ_DISMISSED
for each pending FSF request in zfcp_fsf_req_dismiss_all().
In order to find the root cause, we need to see all pseudo responses even
if the channel presented them successfully with FSF_PROT_GOOD and FSF_GOOD.

Therefore, check zfcp_fsf_req.status for ZFCP_STATUS_FSFREQ_DISMISSED
or ZFCP_STATUS_FSFREQ_ERROR and trace with a new tag "fs_rerr".

It does not matter that there are numerous places which set
ZFCP_STATUS_FSFREQ_ERROR after the location where we trace an FSF response
early. These cases are based on protocol status != FSF_PROT_GOOD or
== FSF_PROT_FSF_STATUS_PRESENTED and are thus already traced by default
as trace tag "fs_perr" or "fs_ferr" respectively.

NB: The trace record with tag "fssrh_1" for status read buffers on dismiss
all remains. zfcp_fsf_req_complete() handles this and returns early.
All other FSF request types are handled separately and as described above.

Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 8a36e4532ea1 ("[SCSI] zfcp: enhancement of zfcp debug features")
Fixes: 2e261af84cdb ("[SCSI] zfcp: Only collect FSF/HBA debug data for matching trace levels")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: fix payload with full FCP_RSP IU in SCSI trace records

commit 12c3e5754c8022a4f2fd1e9f00d19e99ee0d3cc1 upstream.

If the FCP_RSP UI has optional parts (FCP_SNS_INFO or FCP_RSP_INFO) and
thus does not fit into the fsp_rsp field built into a SCSI trace record,
trace the full FCP_RSP UI with all optional parts as payload record
instead of just FCP_SNS_INFO as payload and
a 1 byte RSP_INFO_CODE part of FCP_RSP_INFO built into the SCSI record.

That way we would also get the full FCP_SNS_INFO in case a
target would ever send more than
min(SCSI_SENSE_BUFFERSIZE==96, ZFCP_DBF_PAY_MAX_REC==256)==96.

The mandatory part of FCP_RSP IU is only 24 bytes.
PAYload costs at least one full PAY record of 256 bytes anyway.
We cap to the hardware response size which is only FSF_FCP_RSP_SIZE==128.
So we can just put the whole FCP_RSP IU with any optional parts into
PAYload similarly as we do for SAN PAY since v4.9 commit aceeffbb59bb
("zfcp: trace full payload of all SAN records (req,resp,iels)").
This does not cause any additional trace records wasting memory.

Decoded trace records were confusing because they showed a hard-coded
sense data length of 96 even if the FCP_RSP_IU field FCP_SNS_LEN showed
actually less.

Since the same commit, we set pl_len for SAN traces to the full length of a
request/response even if we cap the corresponding trace.
In contrast, here for SCSI traces we set pl_len to the pre-computed
length of FCP_RSP IU considering SNS_LEN or RSP_LEN if valid.
Nonetheless we trace a hardcoded payload of length FSF_FCP_RSP_SIZE==128
if there were optional parts.
This makes it easier for the zfcpdbf tool to format only the relevant
part of the long FCP_RSP UI buffer. And any trailing information is still
available in the payload trace record just in case.

Rename the payload record tag from "fcp_sns" to "fcp_riu" to make the new
content explicit to zfcpdbf which can then pick a suitable field name such
as "FCP rsp IU all:" instead of "Sense info :"
Also, the same zfcpdbf can still be backwards compatible with "fcp_sns".

Old example trace record before this fix, formatted with the tool zfcpdbf
from s390-tools:

Timestamp      : ...
Area           : SCSI
Subarea        : 00
Level          : 3
Exception      : -
CPU id         : ..
Caller         : 0x...
Record id      : 1
Tag            : rsl_err
Request id     : 0x<request_id>
SCSI ID        : 0x...
SCSI LUN       : 0x...
SCSI result    : 0x00000002
SCSI retries   : 0x00
SCSI allowed   : 0x05
SCSI scribble  : 0x<request_id>
SCSI opcode    : 00000000 00000000 00000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU     : 00000000 00000000 00000202 00000000
                                       ^^==FCP_SNS_LEN_VALID
                 00000020 00000000
                 ^^^^^^^^==FCP_SNS_LEN==32
Sense len      : 96 <==min(SCSI_SENSE_BUFFERSIZE,ZFCP_DBF_PAY_MAX_REC)
Sense info     : 70000600 00000018 00000000 29000000
                 00000400 00000000 00000000 00000000
                 00000000 00000000 00000000 00000000<==superfluous
                 00000000 00000000 00000000 00000000<==superfluous
                 00000000 00000000 00000000 00000000<==superfluous
                 00000000 00000000 00000000 00000000<==superfluous

New example trace records with this fix:

Timestamp      : ...
Area           : SCSI
Subarea        : 00
Level          : 3
Exception      : -
CPU ID         : ..
Caller         : 0x...
Record ID      : 1
Tag            : rsl_err
Request ID     : 0x<request_id>
SCSI ID        : 0x...
SCSI LUN       : 0x...
SCSI result    : 0x00000002
SCSI retries   : 0x00
SCSI allowed   : 0x03
SCSI scribble  : 0x<request_id>
SCSI opcode    : a30c0112 00000000 02000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU     : 00000000 00000000 00000a02 00000200
                 00000020 00000000
FCP rsp IU len : 56
FCP rsp IU all : 00000000 00000000 00000a02 00000200
                                       ^^=FCP_RESID_UNDER|FCP_SNS_LEN_VALID
                 00000020 00000000 70000500 00000018
                 ^^^^^^^^==FCP_SNS_LEN
                                   ^^^^^^^^^^^^^^^^^
                 00000000 240000cb 00011100 00000000
                 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
                 00000000 00000000
                 ^^^^^^^^^^^^^^^^^==FCP_SNS_INFO

Timestamp      : ...
Area           : SCSI
Subarea        : 00
Level          : 1
Exception      : -
CPU ID         : ..
Caller         : 0x...
Record ID      : 1
Tag            : lr_okay
Request ID     : 0x<request_id>
SCSI ID        : 0x...
SCSI LUN       : 0x...
SCSI result    : 0x00000000
SCSI retries   : 0x00
SCSI allowed   : 0x05
SCSI scribble  : 0x<request_id>
SCSI opcode    : <CDB of unrelated SCSI command passed to eh handler>
FCP rsp inf cod: 0x00
FCP rsp IU     : 00000000 00000000 00000100 00000000
                 00000000 00000008
FCP rsp IU len : 32
FCP rsp IU all : 00000000 00000000 00000100 00000000
                                       ^^==FCP_RSP_LEN_VALID
                 00000000 00000008 00000000 00000000
                          ^^^^^^^^==FCP_RSP_LEN
                                   ^^^^^^^^^^^^^^^^^==FCP_RSP_INFO

Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 250a1352b95e ("[SCSI] zfcp: Redesign of the debug tracing for SCSI records.")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: fix missing trace records for early returns in TMF eh handlers

commit 1a5d999ebfc7bfe28deb48931bb57faa8e4102b6 upstream.

For problem determination we need to see that we were in scsi_eh
as well as whether and why we were successful or not.

The following commits introduced new early returns without adding
a trace record:

v2.6.35 commit a1dbfddd02d2
("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh")
on fc_block_scsi_eh() returning != 0 which is FAST_IO_FAIL,

v2.6.30 commit 63caf367e1c9
("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp")
on not having gotten an FSF request after the maximum number of retry
attempts and thus could not issue a TMF and has to return FAILED.

Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: a1dbfddd02d2 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh")
Fixes: 63caf367e1c9 ("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: fix passing fsf_req to SCSI trace on TMF to correlate with HBA

commit 9fe5d2b2fd30aa8c7827ec62cbbe6d30df4fe3e3 upstream.

Without this fix we get SCSI trace records on task management functions
which cannot be correlated to HBA trace records because all fields
related to the FSF request are empty (zero).
Also, the FCP_RSP_IU is missing as well as any sense data if available.

This was caused by v2.6.14 commit 8a36e4532ea1 ("[SCSI] zfcp: enhancement
of zfcp debug features") introducing trace records for TMFs but
hard coding NULL for a possibly existing TMF FSF request.
The scsi_cmnd scribble is also zero or unrelated for the TMF request
so it also could not lookup a suitable FSF request from there.

A broken example trace record formatted with zfcpdbf from the s390-tools
package:

Timestamp      : ...
Area           : SCSI
Subarea        : 00
Level          : 1
Exception      : -
CPU ID         : ..
Caller         : 0x...
Record ID      : 1
Tag            : lr_fail
Request ID     : 0x0000000000000000
                   ^^^^^^^^^^^^^^^^ no correlation to HBA record
SCSI ID        : 0x<scsitarget>
SCSI LUN       : 0x<scsilun>
SCSI result    : 0x000e0000
SCSI retries   : 0x00
SCSI allowed   : 0x05
SCSI scribble  : 0x0000000000000000
SCSI opcode    : 2a000017 3bb80000 08000000 00000000
FCP rsp inf cod: 0x00
                   ^^ no TMF response
FCP rsp IU     : 00000000 00000000 00000000 00000000
                 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
                 00000000 00000000
                 ^^^^^^^^^^^^^^^^^ no interesting FCP_RSP_IU
Sense len      : ...
^^^^^^^^^^^^^^^^^^^^ no sense data length
Sense info     : ...
^^^^^^^^^^^^^^^^^^^^ no sense data content, even if present

There are some true cases where we really do not have an FSF request:
"rsl_fai" from zfcp_dbf_scsi_fail_send() called for early
returns / completions in zfcp_scsi_queuecommand(),
"abrt_or", "abrt_bl", "abrt_ru", "abrt_ar" from
zfcp_scsi_eh_abort_handler() where we did not get as far,
"lr_nres", "tr_nres" from zfcp_task_mgmt_function() where we're
successful and do not need to do anything because adapter stopped.
For these cases it's correct to pass NULL for fsf_req to _zfcp_dbf_scsi().

Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 8a36e4532ea1 ("[SCSI] zfcp: enhancement of zfcp debug features")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: fix capping of unsuccessful GPN_FT SAN response trace records

commit 975171b4461be296a35e83ebd748946b81cf0635 upstream.

v4.9 commit aceeffbb59bb ("zfcp: trace full payload of all SAN records
(req,resp,iels)") fixed trace data loss of 2.6.38 commit 2c55b750a884
("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
necessary for problem determination, e.g. to see the
currently active zone set during automatic port scan.

While it already saves space by not dumping any empty residual entries
of the large successful GPN_FT response (4 pages), there are seldom cases
where the GPN_FT response is unsuccessful and likely does not have
FC_NS_FID_LAST set in fp_flags so we did not cap the trace record.
We typically see such case for an initiator WWPN, which is not in any zone.

Cap unsuccessful responses to at least the actual basic CT_IU response
plus whatever fits the SAN trace record built-in "payload" buffer
just in case there's trailing information
of which we would at least see the existence and its beginning.

In order not to erroneously cap successful responses, we need to swap
calling the trace function and setting the CT / ELS status to success (0).

Example trace record pair formatted with zfcpdbf:

Timestamp      : ...
Area           : SAN
Subarea        : 00
Level          : 1
Exception      : -
CPU ID         : ..
Caller         : 0x...
Record ID      : 1
Tag            : fssct_1
Request ID     : 0x<request_id>
Destination ID : 0x00fffffc
SAN req short  : 01000000 fc020000 01720ffc 00000000
                 00000008
SAN req length : 20
|
Timestamp      : ...
Area           : SAN
Subarea        : 00
Level          : 1
Exception      : -
CPU ID         : ..
Caller         : 0x...
Record ID      : 2
Tag            : fsscth2
Request ID     : 0x<request_id>
Destination ID : 0x00fffffc
SAN resp short : 01000000 fc020000 80010000 00090700
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
SAN resp length: 16384
San resp info  : 01000000 fc020000 80010000 00090700
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]
                 00000000 00000000 00000000 00000000 [trailing info]

The fix saves all but one of the previously associated 64 PAYload trace
record chunks of size 256 bytes each.

Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: aceeffbb59bb ("zfcp: trace full payload of all SAN records (req,resp,iels)")
Fixes: 2c55b750a884 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: add handling for FCP_RESID_OVER to the fcp ingress path

commit a099b7b1fc1f0418ab8d79ecf98153e1e134656e upstream.

Up until now zfcp would just ignore the FCP_RESID_OVER flag in the FCP
response IU. When this flag is set, it is possible, in regards to the
FCP standard, that the storage-server processes the command normally, up
to the point where data is missing and simply ignores those.

In this case no CHECK CONDITION would be set, and because we ignored the
FCP_RESID_OVER flag we resulted in at least a data loss or even
-corruption as a follow-up error, depending on how the
applications/layers on top behave. To prevent this, we now set the
host-byte of the corresponding scsi_cmnd to DID_ERROR.

Other storage-behaviors, where the same condition results in a CHECK
CONDITION set in the answer, don't need to be changed as they are
handled in the mid-layer already.

Following is an example trace record decoded with zfcpdbf from the
s390-tools package. We forcefully injected a fc_dl which is one byte too
small:

Timestamp      : ...
Area           : SCSI
Subarea        : 00
Level          : 3
Exception      : -
CPU ID         : ..
Caller         : 0x...
Record ID      : 1
Tag            : rsl_err
Request ID     : 0x...
SCSI ID        : 0x...
SCSI LUN       : 0x...
SCSI result    : 0x00070000
                     ^^DID_ERROR
SCSI retries   : 0x..
SCSI allowed   : 0x..
SCSI scribble  : 0x...
SCSI opcode    : 2a000000 00000000 08000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU     : 00000000 00000000 00000400 00000001
                                       ^^fr_flags==FCP_RESID_OVER
                                         ^^fr_status==SAM_STAT_GOOD
                                            ^^^^^^^^fr_resid
                 00000000 00000000

As of now, we don't actively handle to possibility that a response IU
has both flags - FCP_RESID_OVER and FCP_RESID_UNDER - set at once.

Reported-by: Luke M. Hopkins <lmhopkin@us.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 553448f6c483 ("[SCSI] zfcp: Message cleanup")
Fixes: ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.") (tglx/history.git)
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: fix queuecommand for scsi_eh commands when DIX enabled

commit 71b8e45da51a7b64a23378221c0a5868bd79da4f upstream.

Since commit db007fc5e20c ("[SCSI] Command protection operation"),
scsi_eh_prep_cmnd() saves scmd->prot_op and temporarily resets it to
SCSI_PROT_NORMAL.
Other FCP LLDDs such as qla2xxx and lpfc shield their queuecommand()
to only access any of scsi_prot_sg...() if
(scsi_get_prot_op(cmd) != SCSI_PROT_NORMAL).

Do the same thing for zfcp, which introduced DIX support with
commit ef3eb71d8ba4 ("[SCSI] zfcp: Introduce experimental support for
DIF/DIX").

Otherwise, TUR SCSI commands as part of scsi_eh likely fail in zfcp,
because the regular SCSI command with DIX protection data, that scsi_eh
re-uses in scsi_send_eh_cmnd(), of course still has
(scsi_prot_sg_count() != 0) and so zfcp sends down bogus requests to the
FCP channel hardware.

This causes scsi_eh_test_devices() to have (finish_cmds == 0)
[not SCSI device is online or not scsi_eh_tur() failed]
so regular SCSI commands, that caused / were affected by scsi_eh,
are moved to work_q and scsi_eh_test_devices() itself returns false.
In turn, it unnecessarily escalates in our case in scsi_eh_ready_devs()
beyond host reset to finally scsi_eh_offline_sdevs()
which sets affected SCSI devices offline with the following kernel message:

"kernel: sd H:0:T:L: Device offlined - not ready after error recovery"

Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: ef3eb71d8ba4 ("[SCSI] zfcp: Introduce experimental support for DIF/DIX")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>