OSDN Git Service
Eli Cohen [Thu, 2 Apr 2015 14:07:21 +0000 (17:07 +0300)]
net/mlx5_core: Coding style fix
Put a line of space before return and next statement.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haggai Abramonvsky [Thu, 2 Apr 2015 14:07:20 +0000 (17:07 +0300)]
net/mlx5_core: Fix call to mlx5_core_qp_modify
Pass 0 in the sqd_event parameter.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Thu, 2 Apr 2015 14:07:19 +0000 (17:07 +0300)]
net/mlx5_core: Allocate firmware pages from device's NUMA node
Allocate firmware pages from the NUMA node which is close to the device.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Apr 2015 20:27:13 +0000 (16:27 -0400)]
Merge branch 'tipc-next'
Jon Maloy says:
====================
tipc: remove some unnecessary complexity
The TIPC code is unnecessarily complex in some places, often because
the conditions or assumptions that were the cause for the complexity
are not valid anymore.
In these three commits, we eliminate some cases of such redundant
complexity.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 2 Apr 2015 13:33:02 +0000 (09:33 -0400)]
tipc: simplify link mtu negotiation
When a link is being established, the two endpoints advertise their
respective interface MTU in the transmitted RESET and ACTIVATE messages.
If there is any difference, the lower of the two MTUs will be selected
for use by both endpoints.
However, as a remnant of earlier attempts to introduce TIPC level
routing. there also exists an MTU discovery mechanism. If an intermediate
node has a lower MTU than the two endpoints, they will discover this
through a bisectional approach, and finally adopt this MTU for common use.
Since there is no TIPC level routing, and probably never will be,
this mechanism doesn't make any sense, and only serves to make the
link level protocol unecessarily complex.
In this commit, we eliminate the MTU discovery algorithm,and fall back
to the simple MTU advertising approach. This change is fully backwards
compatible.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 2 Apr 2015 13:33:01 +0000 (09:33 -0400)]
tipc: eliminate delayed link deletion at link failover
When a bearer is disabled manually, all its links have to be reset
and deleted. However, if there is a remaining, parallel link ready
to take over a deleted link's traffic, we currently delay the delete
of the removed link until the failover procedure is finished. This
is because the remaining link needs to access state from the reset
link, such as the last received packet number, and any partially
reassembled buffer, in order to perform a successful failover.
In this commit, we do instead move the state data over to the new
link, so that it can fulfill the procedure autonomously, without
accessing any data on the old link. This means that we can now
proceed and delete all pertaining links immediately when a bearer
is disabled. This saves us from some unnecessary complexity in such
situations.
We also choose to change the confusing definitions CHANGEOVER_PROTOCOL,
ORIGINAL_MSG and DUPLICATE_MSG to the more descriptive TUNNEL_PROTOCOL,
FAILOVER_MSG and SYNCH_MSG respectively.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 2 Apr 2015 13:33:00 +0000 (09:33 -0400)]
tipc: drop tunneled packet duplicates at reception
In commit
8b4ed8634f8b3f9aacfc42b4a872d30c36b9e255
("tipc: eliminate race condition at dual link establishment")
we introduced a parallel link synchronization mechanism that
guarentees sequential delivery even for users switching from
an old to a newly established link. The new mechanism makes it
unnecessary to deliver the tunneled duplicate packets back to
the old link, as we are currently doing. It is now sufficient
to use the last tunneled packet's inner sequence number as
synchronization point between the two parallel links, whereafter
it can be dropped.
In this commit, we drop the duplicate packets arriving on the new
link, after updating the synchronization point at each new arrival.
Although it would now have been sufficient for the other endpoint
to only tunnel the last packet in its send queue, and not the
entire queue, we must still do this to maintain compatibility
with older nodes.
This commit makes it possible to get rid if some complex
interaction between the two parallel links.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Apr 2015 20:25:27 +0000 (16:25 -0400)]
Merge branch 'mlx4-next'
Or Gerlitz says:
====================
Mellanox mlx4 driver updates
The main feature added by this series are Ido's changes to support
Granular QoS for VFs, where for the time being only max rate is supported.
Muhammad added support for setting rx-fcs and rx-all through ethtool,
and Ido did the interface identify work.
Last, add Ido as a maintainer for the mlx4 Ethernet driver!
Some of next week is the Passover holiday here and I will be
mostly OOO. If needed (...) Ido or Amir will send V1 and such.
Rebased against net-next commit
033f46b "crypto: algif -
explicitly mark end of data".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Thu, 2 Apr 2015 13:31:23 +0000 (16:31 +0300)]
MAINTAINERS: Update mlx4_en entry
Add Ido Shamay as co-maintainer for the mlx4 Ethernet driver.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Muhammad Mahajna [Thu, 2 Apr 2015 13:31:22 +0000 (16:31 +0300)]
net/mlx4_en: Add RX-ALL support
Enabled when the device supports KEEP FCS and IGNORE FCS.
When the flag is set, pass all received frames up the stack,
even ones with invalid FCS, controlled by ethtool.
Signed-off-by: Muhammad Mahajna <muhammadm@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Muhammad Mahajna [Thu, 2 Apr 2015 13:31:21 +0000 (16:31 +0300)]
net/mlx4_en: Add RX-FCS support
Enabled when device supports KEEP FCS. When the flag is set, Ethernet FCS
is appended to the end of the frame, controlled by ethtool.
Signed-off-by: Muhammad Mahajna <muhammadm@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:20 +0000 (16:31 +0300)]
net/mlx4_en: Add interface identify support
Add support for the interface ethtool identify feature.
Make the physical port LED to blink with green and yellow colors.
The device handles the LED blink by itself (synchrous use of
set_phys_id), by returning 0 to ETHTOOL_ID_ACTIVE command.
Signed-off-by: Eyal Grossman <eyalgr@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:19 +0000 (16:31 +0300)]
net/mlx4: Add SET_PORT opcode modifiers enumeration
The calls to SET_PORT used hard-code numbers, when supplying command's
opcode modifiers, fix that to use well defined constants.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:18 +0000 (16:31 +0300)]
net/mlx4: Set enhanced QoS support by default when ETS supported
If HCA supports ETS QoS feature, set enhanced QoS bit in init_hca as default.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:17 +0000 (16:31 +0300)]
net/mlx4: Warn users of depracated QoS Firmware
A new capability bit was introduced in the past to to differ devices
using the QoS ETS feature. The old was deprecated since then.
If driver sees device which set only the old capabilty, it will print
warning to user suggesting to upgrade the FW.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:16 +0000 (16:31 +0300)]
net/mlx4_en: Enable TX rate limit per VF
Support granular QoS per VF, by implementing the ndo_set_vf_rate.
Enforce a rate limit per VF when called, and enabled only for VFs in
VST mode with user priority supported by the device.
We don't enforce VFs to be in VST mode at the moment of configuration,
but rather save the given rate limit and enforce it when the VF is
moved to VST with user priority which is supported (currently 0).
VST<->VGT or VST qos value state changes are disallowed when a rate
limit is configured. Minimum BW share is not supported yet.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:15 +0000 (16:31 +0300)]
net/mlx4: Added qos_vport QP configuration in VST mode
Granular QoS per VF feature introduce a new QP field, qos_vport.
PF administrator can connect VF QPs to a certain QoS Vport, to
inherit its proporties. Connecting QPs to the default QoS Vport
(defined as 0) is always allowed, even when there are no allocated VPPs.
At this point, only the default vport is connected to QPs.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:14 +0000 (16:31 +0300)]
net/mlx4: Allocate VPPs for each port on PF init
Initialization of granular Qos per VF mechanism.
Query the port availible VPPs and allocates those on all supported
priorities in an equal share. Allocation is done only in SRIOV mode,
when the feature is supported by the device and port type is Ethernet.
Allocation currently is done only on the default priority 0.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:13 +0000 (16:31 +0300)]
net/mlx4: Query device for QoS per VF support
Checks in QUERY_DEV_CAP if the granular QoS per VF feature is
supported by the device. Disabled for guests.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:12 +0000 (16:31 +0300)]
net/mlx4: Add mlx4_SET_VPORT_QOS implementation
Add the SET_VPORT_QOS device command, which is ntended for virtual
granular QoS configuration per VF in SRIOV mode. The SET_VPORT_QOS
command sets and queries QoS parameters of a VPort. Each priority
allowed for a VPort is assigned with a share of the BW, and a BW
limitation. QoS parameters can be modified at any time, but must be
initialized before any QP is associated with the VPort.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:11 +0000 (16:31 +0300)]
net/mlx4: Add mlx4_ALLOCATE_VPP implementation
Implements device ALLOCATE_VPP command, to be used for granular QoS
configuration of VFs by the PF device. Defines and queries the amount
of VPPs assigned to each port, and the amount of VPPs assigned to each
priority of each port. Once the total VPPs are split between the priorities
of a port, they may be assigned with a share of the BW or a rate limit.
Split into two functions (get/set) whoch are supplied with
mlx4_alloc_vpp_context and physical port number.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:10 +0000 (16:31 +0300)]
net/mlx4: New file for QoS related firmware commands
Create two new files fw_qos.h and fw_qos.c in mlx4_core module.
It gathers all relevant QoS firmware related commands etc, thus improving
encapsulation of the mlx4_core module. For now it contains the QoS existing
commands: mlx4_SET_PORT_SCHEDULER and mlx4_SET_PORT_PRIO2TC.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:09 +0000 (16:31 +0300)]
net/mlx4: Aesthetic code changes in multi_func_init
Previous vf_oper and vf_admin code created very long lines, making it hard
to read the code. Added relevant in-struct pointers to reduce code
complexity and avoid code lines spread over 80 lines. Same logic is preserved.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:08 +0000 (16:31 +0300)]
net/mlx4: Make mlx4_is_eth visible inline funcion
Currently implemented as static function in resource_tracker.c --
this change will allow other files in mlx4_core to use it as well.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:07 +0000 (16:31 +0300)]
net/mlx4_en: Change loopback only upon feature change
Currently any change of netdev features results in a call to
mlx4_en_update_loopback_state(). Those calls are unnecessary,
and should be called only upon loopback feature change.
Also moved some of the logic into mlx4_en_update_loopback_state().
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Thu, 2 Apr 2015 13:31:06 +0000 (16:31 +0300)]
net/mlx4: Add RSS support for fragmented IP datagrams
Enable RSS support for fragmented IP packets, when device supports it.
Until now, fragmented IP packets were directed only to the default_qpn.
Since IP fragments (datagram) have no upper protocols (L3 IP packets),
hash is performed on 3-tuple - dst MAC, source IP and dest IP. The HW
makes sure that this holds for the 1st fragment too, so all fragments
go to the same QP.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Apr 2015 20:16:53 +0000 (16:16 -0400)]
Merge git://git./linux/kernel/git/davem/net
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 2 Apr 2015 18:30:36 +0000 (11:30 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"This time we have addition of caps for jz4740 which fixes intentional
warning at boot. Then we have memory leak issues in drivers using
virt-dma by Peter on few drive"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: moxart-dma: Fix memory leak when stopping a running transfer
dmaengine: bcm2835-dma: Fix memory leak when stopping a running transfer
dmaengine: omap-dma: Fix memory leak when terminating running transfer
dmaengine: edma: fix memory leak when terminating running transfers
dmaengine: jz4740: Define capabilities
Linus Torvalds [Thu, 2 Apr 2015 18:09:41 +0000 (11:09 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix use-after-free with mac80211 RX A-MPDU reorder timer, from
Johannes Berg.
2) iwlwifi leaks memory every module load/unload cycles, fix from Larry
Finger.
3) Need to use for_each_netdev_safe() in rtnl_group_changelink()
otherwise we can crash, from WANG Cong.
4) mlx4 driver does register_netdev() too early in the probe sequence,
from Ido Shamay.
5) Don't allow router discovery hop limit to decrease the interface's
hop limit, from D.S. Ljungmark.
6) tx_packets and tx_bytes improperly accounted for certain classes of
USB network devices, fix from Ben Hutchings.
7) ip{6}mr_rules_init() mistakenly use plain kfree to release the ipmr
tables in the error path, they must instead use ip{6}mr_free_table().
Fix from WANG Cong.
8) cxgb4 doesn't properly quiesce all RX activity before unregistering
the netdevice. Fix from Hariprasad Shenai.
9) Fix hash corruptions in ipvlan driver, from Jiri Benc.
10) nla_memcpy(), like a real memcpy, should fully initialize the
destination buffer, even if the source attribute is smaller. Fix
from Jiri Benc.
11) Fix wrong error code returned from iucv_sock_sendmsg(). We should
use whatever sock_alloc_send_skb() put into 'err'. From Eugene
Crosser.
12) Fix slab object leak on module unload in TIPC, from Ying Xue.
13) Need a READ_ONCE() when reading the cached RX socket route in
tcp_v{4,6}_early_demux(). From Michal Kubecek.
14) Still too many problems with TPC support in the ath9k driver, so
disable it for now. From Felix Fietkau.
15) When in AP mode the rtlwifi driver can leak DMA mappings, fix from
Larry Finger.
16) Missing kzalloc() failure check in gs_usb CAN driver, from Colin Ian
King.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
cxgb4: Fix to dump devlog, even if FW is crashed
cxgb4: Firmware macro changes for fw verison 1.13.32.0
bnx2x: Fix kdump when iommu=on
bnx2x: Fix kdump on 4-port device
mac80211: fix RX A-MPDU session reorder timer deletion
MAINTAINERS: Update Intel Wired Ethernet Driver info
tipc: fix a slab object leak
net/usb/r8152: add device id for Lenovo TP USB 3.0 Ethernet
af_iucv: fix AF_IUCV sendmsg() errno
openvswitch: Return vport module ref before destruction
netlink: pad nla_memcpy dest buffer with zeroes
bonding: Bonding Overriding Configuration logic restored.
ipvlan: fix check for IP addresses in control path
ipvlan: do not use rcu operations for address list
ipvlan: protect against concurrent link removal
ipvlan: fix addr hash list corruption
net: fec: setup right value for mdio hold time
net: tcp6: fix double call of tcp_v6_fill_cb()
cxgb4vf: Fix sparse warnings
netns: don't clear nsid too early on removal
...
David S. Miller [Thu, 2 Apr 2015 18:05:02 +0000 (14:05 -0400)]
Merge branch 'netdev_iflink_remove'
Nicolas Dichtel says:
====================
Remove iflink field from the net_device structure
The first goal of this series was to advertise the veth peer via the IFLA_LINK
attribute, but iflink was not ready for network namespaces.
The iflink of an interface should be set to its ifindex for a physical interface
and to another value (0 if not relevant) for a virtual interface.
This was not the case for some interfaces, like vxlan, bond, or bridge for
example.
There is also a risk, if the targeted interface moves to another netns, that the
ifindex changes without updating corresponding iflink fields (eg. vlan).
Moving the management of this property into virtual interface drivers allows to
better handle this last case because most of virtual interface drivers have a
pointer to the link netdevice.
Anyway, dev->iflink value was always a copy of some internal data of the virtual
interface driver, thus let's use these internal data directly.
So, this series removes the iflink field and let the drivers manage it.
Only the last patch was present in the v1, but I fully rework it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:11 +0000 (17:07 +0200)]
veth: set iflink to the peer veth
Now that the peer netns is advertised in rtnl messages, we can set this property
so that IFLA_LINK will advertise the peer ifindex. It allows the userland to get
the full veth configuration.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:10 +0000 (17:07 +0200)]
dev: set iflink to 0 for virtual interfaces
Virtual interfaces are supposed to set an iflink value != of their ifindex.
It was not the case for some of them, like vxlan, bond or bridge.
Let's set iflink to 0 when dev->rtnl_link_ops is set.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:09 +0000 (17:07 +0200)]
net: remove iflink field from struct net_device
Now that all users of iflink have the ndo_get_iflink handler available, it's
possible to remove this field.
By default, dev_get_iflink() returns the ifindex of the interface.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:08 +0000 (17:07 +0200)]
dsa: implement ndo_get_iflink
Don't use dev->iflink anymore.
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:07 +0000 (17:07 +0200)]
infiniband/ipoib: implement ndo_get_iflink
Don't use dev->iflink anymore.
CC: Roland Dreier <roland@kernel.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:06 +0000 (17:07 +0200)]
ipvlan: implement ndo_get_iflink
Don't use dev->iflink anymore.
CC: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:05 +0000 (17:07 +0200)]
macvlan: implement ndo_get_iflink
Don't use dev->iflink anymore.
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:04 +0000 (17:07 +0200)]
vlan: implement ndo_get_iflink
Don't use dev->iflink anymore.
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:03 +0000 (17:07 +0200)]
ipmr,ip6mr: implement ndo_get_iflink
Don't use dev->iflink anymore.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:02 +0000 (17:07 +0200)]
ipip,gre,vti,sit: implement ndo_get_iflink
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:01 +0000 (17:07 +0200)]
ip6tnl,gre6,vti6: implement ndo_get_iflink
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 2 Apr 2015 15:07:00 +0000 (17:07 +0200)]
dev: introduce dev_get_iflink()
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tadeusz.struk@intel.com [Wed, 1 Apr 2015 20:53:06 +0000 (13:53 -0700)]
crypto: algif - explicitly mark end of data
After the TX sgl is expanded we need to explicitly mark end of data
at the last buffer that contains data.
Changes in v2
- use type 'bool' and true/false for 'mark'.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Apr 2015 02:55:41 +0000 (22:55 -0400)]
Merge branch 'dsa-next'
Andrew Lunn says:
====================
DSA Mavell drivers refactoring and cleanup
v1->v2:
* Add missing signed-of-by: For patches authored by Guenter Roeck.
* Add Reviewed by from Guenter Roack to patch #5.
This is a collection of patches again net-next from today containing
refactoring and consolidate of code, cleanups and using #define's to
replace register numbers.
Patch #1 Swaps the 6131 driver to use the consolidated setup code.
Patch #2 Moves the Switch IDs used during probe into a central
location. We need these later so that we can differentiate
the different features the devices have.
Patch #3 Makes the 6131 driver set the number of ports in the private
state structure. It then uses this, rather than hard coded
maximum number of ports.
Patch #4 Similar to Patch #3, but for the 6123_61_65 driver.
Patch #5 Similar to Patch #3, and #4, but for all the remaining
drivers. This greatly increases the similarity of the code
between drivers, allow further patches to consolidate the
duplicated code.
Patch #6 Consolidate the switch reset code, which has two minor
variants. Removes around 35 lines per driver.
Patch #7 Moves phy page access functions out of the 6352 driver into
the shared code. Currently only the 6352 driver uses this,
but it is likely other devices will come along wanting this
functionality.
Patch #8 Consolidates the code used to access phy registers. Removes
around 40 lines of code per driver.
Patch #9 Fixes missing mutex locking in the EEE code, and refactors
the code a bit to make it more understandable with respect to
locks.
Patch #10 Consolidates reading statistics. This is very similar code
for all devices, but the number of available statistics
differ, which can be determined from the product ID. Removes
around 65 lines per driver.
Patch #11 Add #defines for registers, and bits within the
registers. For the moment, this is limited to the shared
code. The individual drivers will be converted once the
remaining duplicated code is consolidated
Patch #12 Fix broken statistic counters on the 6172. The 6352 family
requires the port number is poked into a different set of
bits in the register compared to other devices.
Many thanks to Guenter Roeck for repeatedly reviewing the patches and
testing them on his hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 2 Apr 2015 02:06:40 +0000 (04:06 +0200)]
net: dsa: mv88e6xxx: Fix stats counters for 6352 family
The statistic counters for the mv88e6172 never worked. This device is
a member of the 6352 family of chips, which has a slightly different
layout of the register used for capturing statistics. Add support for
detecting this family and poking the port in the right place in the
register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 2 Apr 2015 02:06:39 +0000 (04:06 +0200)]
net: dsa: Use mnemonics rather than register numbers
Rather than refer to registers by number, define mnemonics. Also
define mnemonics for the commonly used bits within the registers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 2 Apr 2015 02:06:38 +0000 (04:06 +0200)]
net: dsa: Consolidate getting the statistics
Reading the statistics from the hardware is the same for all
chips. What differs is the number of available statistics. Have just
one copy of the code in the shared mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 2 Apr 2015 02:06:37 +0000 (04:06 +0200)]
net: dsa: mv88e6xxx: Add missing mutex's in EEE operations.
The phy_mutex should be held while reading and writing to the phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 2 Apr 2015 02:06:36 +0000 (04:06 +0200)]
net: dsa: Consolidate phy read and write functions
Move the common code for reading and writing phy registers into the
shared mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 2 Apr 2015 02:06:35 +0000 (04:06 +0200)]
net: dsa: Move phy page access functions into shared code
These functions could in future be used by other drivers. Move them
into the shared area.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 2 Apr 2015 02:06:34 +0000 (04:06 +0200)]
net: dsa: Centralize Marvell switch reset
Marvell switches are all reset in nearly the same way. The only
difference is if the PPU should be enabled or not. Move this
code into the shared mv88x6xxx.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 2 Apr 2015 02:06:33 +0000 (04:06 +0200)]
net: dsa: Consistently set and use ps->num_ports
As a step towards consolidating code, consistently set the
number of ports in the private state structure, and make use of it in
loops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Thu, 2 Apr 2015 02:06:32 +0000 (04:06 +0200)]
net: dsa: mv88e6123_61_65: Determine and use number of switch ports
Determine and use number of switch ports from chip ID instead of always
using the maximum, and return error when an attempt is made to access a
non-existing port.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Thu, 2 Apr 2015 02:06:31 +0000 (04:06 +0200)]
net: dsa: mv88e6131: Determine and use number of switch ports
Determine and use number of switch ports from chip ID instead of always
using the maximum, and return error when an attempt is made to access a
non-existing port.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Thu, 2 Apr 2015 02:06:30 +0000 (04:06 +0200)]
net: dsa: mv88e6xxx: Move switch product IDs into common include file
This will let us use the switch product IDs in the common source code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Thu, 2 Apr 2015 02:06:29 +0000 (04:06 +0200)]
net: dsa: mv88e6131: Use common initialization functions
Common initialization functions will be needed to enable
HW bridging support.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Thu, 2 Apr 2015 02:20:23 +0000 (11:20 +0900)]
pkt_sched: fq: correct spelling of locally
Correct spelling of locally.
Also remove extra space before tab character in struct fq_flow.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Thu, 2 Apr 2015 02:17:58 +0000 (11:17 +0900)]
vxlan: correct spelling in comments
Fix some spelling / typos:
* droppped -> dropped
* asddress -> address
* compatbility -> compatibility
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Wed, 1 Apr 2015 22:33:08 +0000 (15:33 -0700)]
vmxnet3: spelling fixes
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Wed, 1 Apr 2015 19:29:13 +0000 (12:29 -0700)]
vxge: Add const to ethtool_driver_stats_keys
Move about half a KB of data to text.
Miscellanea:
o Move strings out of the .h file into the .c file
in case the .h file is ever #included twice
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tadeusz Struk [Mon, 30 Mar 2015 21:25:44 +0000 (14:25 -0700)]
crypto: algif - use kmalloc instead of kzalloc
No need to use kzalloc to allocate sgls as the structure is initialized anyway.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tadeusz Struk [Mon, 30 Mar 2015 21:25:43 +0000 (14:25 -0700)]
crypto: af_alg - make exports consistant
Use EXPORT_SYMBOL_GPL instead of EXPORT_SYMBOL.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Apr 2015 18:48:50 +0000 (14:48 -0400)]
Merge tag 'wireless-drivers-for-davem-2015-04-01' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* fix a memory leak, we leaked memory each time the module
was loaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Apr 2015 18:47:21 +0000 (14:47 -0400)]
Merge branch 'cxgb4-net'
Hariprasad Shenai says:
====================
cxgb4 FW macro changes for new FW
Fix to dump device log even in the case of firmware crash. Also
incorporates changes for new FW.
This patch series has been created against net tree and includes patches on
cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 1 Apr 2015 16:11:16 +0000 (21:41 +0530)]
cxgb4: Fix to dump devlog, even if FW is crashed
Add new Common Code routines to retrieve Firmware Device Log
parameters from PCIE_FW_PF[7]. The firmware initializes its Device Log very
early on and stores the parameters for its location/size in that register.
Using the parameters from the register allows us to access the Firmware
Device Log even when the firmware crashes very early on or we're not
attached to the firmware
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 1 Apr 2015 16:11:15 +0000 (21:41 +0530)]
cxgb4: Firmware macro changes for fw verison 1.13.32.0
Adds new macro and few macro changes for fw version 1.13.32.0 also
changes version string in driver to match 1.13.32.0
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Wed, 1 Apr 2015 15:49:24 +0000 (08:49 -0700)]
chelsio cxgb/cxgb3: Make stats_strings arrays const
Move ~2KB of strings in each driver from data to text.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Apr 2015 18:27:28 +0000 (14:27 -0400)]
Merge tag 'wireless-drivers-next-for-davem-2015-04-01' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
ath9k:
* add Active Interference Cancellation, a method implemented in the HW
to counter WLAN RX > sensitivity degradation when BT is transmitting
at the same time. This feature is supported by cards like WB222
based on AR9462.
iwlwifi:
* Location Aware Regulatory was added by Arik
* 8000 device family work
* update to the BT Coex firmware API
brmcfmac:
* add new BCM43455 and BCM43457 SDIO device support
* add new BCM43430 SDIO device support
wil6210:
* take care of AP bridging
* fix NAPI behavior
* found approach to achieve 4*n+2 alignment of Rx frames
rt2x00:
* add new rt2800usb device DWA 130
rtlwifi:
* add USB ID for D-Link DWA-131
* add USB ID ASUS N10 WiFi dongle
mwifiex:
* throughput enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Apr 2015 18:19:22 +0000 (14:19 -0400)]
Merge tag 'mac80211-for-davem-2015-04-01' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This contains just a single fix for a crash I happened to randomly
run into today during testing. It's clearly been around for a while,
but is pretty hard to trigger, even when I tried explicitly (and
modified the code to make it more likely) it rarely did.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Apr 2015 17:58:06 +0000 (13:58 -0400)]
Merge tag 'linux-can-next-for-4.1-
20150401' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-04-01
this is a pull request of 5 patches for net-next/master.
There are two patches for the ems_usb driver by Gerhard Uttenthaler and
me, which fix sparse endianess warnings. Oliver Hartkopp adds two
patches to improve and extend the CAN-ID filter handling on RAW CAN
sockets. The last patch is by me, it silences an uninitialized variable
warning in the peak_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Wed, 1 Apr 2015 07:40:00 +0000 (00:40 -0700)]
net: bcmgenet: enable MoCA link state change detection
Currently, MoCA fixed PHYs are always in link-up state, regardless of
whether the link is actually up or not.
Add code to properly detect MoCA link state changes and to reflect the
new state in MoCA fixed PHY. Only GENET V3 and V4 MACs are capable of
detecting MoCA link state changes.
The code works as follows:
1. GENET MAC detects MoCA link state change and issues UMAC_IRQ_LINK_UP
or UMAC_IRQ_LINK_DOWN interrupt.
2. Link up/down interrupt is processed in bcmgenet_irq_task(), which
calls phy_mac_interrupt().
3. phy_mac_interrupt() updates the fixed PHY phydev->link and kicks
the PHY state machine.
4. PHY state machine proceeds to read the fixed PHY link status
register.
5. When the fixed PHY link status register is being read, the new
function bcmgenet_fixed_phy_link_update() gets called. It copies
the fixed PHY phydev->link value to the fixed PHY status->link.
6. PHY state machine receives the new link state of the fixed PHY.
7. MoCA fixed PHY link state now correctly reflects the real MoCA
hardware link state.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 1 Apr 2015 17:29:55 +0000 (10:29 -0700)]
Merge tag 'iommu-fixes-v4.0-rc6' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"This contains fixes for:
- a VT-d issue where hardware domain-ids might be freed while still
in use.
- an ipmmu-vmsa issue where where the device-table was not zero
terminated
- unchecked register access issue in the arm-smmu driver"
* tag 'iommu-fixes-v4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Remove unused variable
iommu: ipmmu-vmsa: Add terminating entry for ipmmu_of_ids
iommu/vt-d: Detach domain *only* from attached iommus
iommu/arm-smmu: fix ARM_SMMU_FEAT_TRANS_OPS condition
Rusty Russell [Wed, 1 Apr 2015 06:33:30 +0000 (17:03 +1030)]
lguest: now needs PCI_DIRECT.
Since commit
8e7094694396 ("lguest: add a dummy PCI host bridge.")
lguest uses PCI, but it needs you to frob the ports directly.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 1 Apr 2015 17:05:42 +0000 (10:05 -0700)]
Merge tag 'lazytime_fix' of git://git./linux/kernel/git/tytso/ext4
Pull lazytime fixes from Ted Ts'o:
"This fixes a problem in the lazy time patches, which can cause
frequently updated inods to never have their timestamps updated.
These changes guarantee that no timestamp on disk will be stale by
more than 24 hours"
* tag 'lazytime_fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
fs: add dirtytime_expire_seconds sysctl
fs: make sure the timestamps for lazytime inodes eventually get written
Linus Torvalds [Wed, 1 Apr 2015 16:45:47 +0000 (09:45 -0700)]
Merge branch 'for-4.0' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Two main issues:
- We found that turning on pNFS by default (when it's configured at
build time) was too aggressive, so we want to switch the default
before the 4.0 release.
- Recent client changes to increase open parallelism uncovered a
serious bug lurking in the server's open code.
Also fix a krb5/selinux regression.
The rest is mainly smaller pNFS fixes"
* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
sunrpc: make debugfs file creation failure non-fatal
nfsd: require an explicit option to enable pNFS
NFSD: Fix bad update of layout in nfsd4_return_file_layout
NFSD: Take care the return value from nfsd4_encode_stateid
NFSD: Printk blocklayout length and offset as format 0x%llx
nfsd: return correct lockowner when there is a race on hash insert
nfsd: return correct openowner when there is a race to put one in the hash
NFSD: Put exports after nfsd4_layout_verify fail
NFSD: Error out when register_shrinker() fail
NFSD: Take care the return value from nfsd4_decode_stateid
NFSD: Check layout type when returning client layouts
NFSD: restore trace event lost in mismerge
Uwe Kleine-König [Tue, 31 Mar 2015 20:08:45 +0000 (22:08 +0200)]
net: phy: at803x: simplify using devm_gpiod_get_optional and its 4th argument
Since
39b2bbe3d715 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Moreover use devm_gpiod_get_optional instead of ignoring all errors
returned by devm_gpiod_get and simplify accordingly.
The result is more strict error handling which is good.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rasmus Villemoes [Tue, 31 Mar 2015 14:05:23 +0000 (16:05 +0200)]
caif: remove unused struct member
The tty_name member of struct ser_device is never set or used, so it
can be removed. (The definition of struct ser_device is private to
this .c file, and the identifier tty_name only occurs in this one
place.)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Apr 2015 16:30:39 +0000 (12:30 -0400)]
Merge branch 'bnx2'
Yuval Mintz says:
====================
bnx2x: kdump related fixes
This patch series aims to fix bnx2x driver issues when loading in kdump kernel.
Both issues fixed here would be fatal to the device, requiring full reset of
the system in order to recover, preventing the device from serving its purpose
in the kdump environment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 1 Apr 2015 07:02:20 +0000 (10:02 +0300)]
bnx2x: Fix kdump when iommu=on
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 1 Apr 2015 07:02:19 +0000 (10:02 +0300)]
bnx2x: Fix kdump on 4-port device
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Wed, 1 Apr 2015 12:20:42 +0000 (14:20 +0200)]
mac80211: fix RX A-MPDU session reorder timer deletion
There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:
* tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
* station is destroyed
* reorder timer fires before ieee80211_free_tid_rx() runs,
accessing the station, thus potentially crashing due to
the use-after-free
The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.
Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marc Kleine-Budde [Wed, 1 Apr 2015 09:49:59 +0000 (11:49 +0200)]
can: pcan_usb: pcan_usb_fd_send_cmd(): silence compiler warning about uninitialized var
This patch silences the compiler warning:
drivers/net/can/usb/peak_usb/pcan_usb_fd.c: In function 'pcan_usb_fd_send_cmd':
drivers/net/can/usb/peak_usb/pcan_usb_fd.c:185:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
by initialising the variable as 0.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Wed, 1 Apr 2015 05:50:29 +0000 (07:50 +0200)]
can: introduce new raw socket option to join the given CAN filters
The CAN_RAW socket can set multiple CAN identifier specific filters that lead
to multiple filters in the af_can.c filter processing. These filters are
indenpendent from each other which leads to logical OR'ed filters when applied.
This socket option joines the given CAN filters in the way that only CAN frames
are passed to user space that matched *all* given CAN filters. The semantic for
the applied filters is therefore changed to a logical AND.
This is useful especially when the filterset is a combination of filters where
the CAN_INV_FILTER flag is set in order to notch single CAN IDs or CAN ID
ranges from the incoming traffic.
As the raw_rcv() function is executed from NET_RX softirq the introduced
variables are implemented as per-CPU variables to avoid extensive locking at
CAN frame reception time.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Wed, 1 Apr 2015 05:50:28 +0000 (07:50 +0200)]
can: fix multiple delivery of a single CAN frame for overlapping CAN filters
The CAN_RAW socket can set multiple CAN identifier specific filters that lead
to multiple filters in the af_can.c filter processing. These filters are
indenpendent from each other which leads to logical OR'ed filters when applied.
This patch makes sure that every CAN frame which is filtered for a specific
socket is only delivered once to the user space. This is independent from the
number of matching CAN filters of this socket.
As the raw_rcv() function is executed from NET_RX softirq the introduced
variables are implemented as per-CPU variables to avoid extensive locking at
CAN frame reception time.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 25 Mar 2015 09:36:17 +0000 (10:36 +0100)]
can: ems_usb: mark timestamp as little endian
The struct ems_cpc_msg describes the a message received from the USB device,
which uses little endian byte order. This patch marks the timestamp in struct
ems_cpc_msg accordingly.
Acked-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Gerhard Uttenthaler [Tue, 24 Mar 2015 18:02:29 +0000 (19:02 +0100)]
can: ems_usb: fix endianess of CAN ID
The device expects the CAN ID in little endian format.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeff Kirsher [Thu, 26 Mar 2015 00:01:03 +0000 (17:01 -0700)]
MAINTAINERS: Update Intel Wired Ethernet Driver info
Update the git tree info with a recent change in tree names. Also
add our new mailing list created solely for Linux kernel patches
and kernel development, as well as the new patchwork project for
tracking patches. Lastly update the list of "reviewers" since a
couple of developers have moved on to different projects.
Made an update to the section header so that it is more manageable
going forward as we add new drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ying Xue [Wed, 1 Apr 2015 01:42:50 +0000 (09:42 +0800)]
tipc: fix a slab object leak
When remove TIPC module, there is a warning to remind us that a slab
object is leaked like:
root@localhost:~# rmmod tipc
[ 19.056226] =============================================================================
[ 19.057549] BUG TIPC (Not tainted): Objects remaining in TIPC on kmem_cache_close()
[ 19.058736] -----------------------------------------------------------------------------
[ 19.058736]
[ 19.060287] INFO: Slab 0xffffea0000519a00 objects=23 used=1 fp=0xffff880014668b00 flags=0x100000000004080
[ 19.061915] INFO: Object 0xffff880014668000 @offset=0
[ 19.062717] kmem_cache_destroy TIPC: Slab cache still has objects
This is because the listening socket of TIPC topology server is not
closed before TIPC proto handler is unregistered with proto_unregister().
However, as the socket is closed in tipc_exit_net() which is called by
unregister_pernet_subsys() during unregistering TIPC namespace operation,
the warning can be eliminated if calling unregister_pernet_subsys() is
moved before calling proto_unregister().
Fixes:
e05b31f4bf89 ("tipc: make tipc socket support net namespace")
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 31 Mar 2015 21:19:19 +0000 (17:19 -0400)]
Merge branch 'ptp-ns_to_timespec64'
Richard Cochran says:
====================
ptp: remove open coded ns_to_timespec64 and reverse
This patch series is a follow up to the recent timespec64 work for the
PTP Hardware Clock drivers. Arnd noticed that drivers are using open
coded implementations of ns_to_timespec64 and timespec64_to_ns. This
series replaces the open coded logic with the helper functions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:13 +0000 (23:08 +0200)]
ptp: ixgbe: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:09 +0000 (23:08 +0200)]
ptp: fec: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:08 +0000 (23:08 +0200)]
ptp: tg3: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() instead of
open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:06 +0000 (23:08 +0200)]
ptp: blackfin: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:16 +0000 (23:08 +0200)]
ptp: cpts: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:15 +0000 (23:08 +0200)]
ptp: stmmac: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() instead of
open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:14 +0000 (23:08 +0200)]
ptp: mlx4: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() instead of
open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:12 +0000 (23:08 +0200)]
ptp: igb: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:11 +0000 (23:08 +0200)]
ptp: e1000e: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() instead of
open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:10 +0000 (23:08 +0200)]
ptp: gianfar: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Tue, 31 Mar 2015 21:08:07 +0000 (23:08 +0200)]
ptp: bnx2x: use helpers for converting ns to timespec.
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>