OSDN Git Service
Samuel Ortiz [Mon, 13 Oct 2014 23:42:23 +0000 (01:42 +0200)]
NFC: Introduce vendor commands structures
Together with inline routines to associate a vendor commands
array with an NFC device.
Vendor commands allow vendors to implement their very specific
operations from driver code instead of adding new stack ops
for non NFC generic commands.
Vendors need to select their own unique IDs and use that as a
namespace for defining sub commands.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:52 +0000 (13:16 +0200)]
NFC: st21nfcb: Configure CLF with NCI proprietary command
In order to prevent any NFC feature when NFC is disable and
to save power, (down to 4uA) put the CLF in hibernate mode
with RF deactivated.
Add the equivalent to enable the NFC feature when initiating
the st21nfcb driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:51 +0000 (13:16 +0200)]
NFC: st21nfcb: disable irq when st21nfcb is disabled
When st21nfcb is disabled, the irq line may remain active
while no data are available, flooding the system with
irrelevant i2c transaction.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:50 +0000 (13:16 +0200)]
NFC: st21nfcb: Move powered flag from phy to ndlc layer
The powered flag can be set from the ndlc_open and ndlc_close layer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:49 +0000 (13:16 +0200)]
NFC: st21nfcb: Move st21nfcb_nci_remove in ndlc_remove
Removing st21nfcb may need to execute some specific commands before
stopping the ndlc state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:48 +0000 (13:16 +0200)]
NFC: nci: Move close ops call in nci_close_device
When closing the device some data (proprietary commands)
might be sent. The core state machine needs to be set for
correct command execution.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:47 +0000 (13:16 +0200)]
NFC: st21nfcb: Add support for nci proprietary commands
On st21nfcb, nci proprietary commands are available to run
specific chip operations (for example: power management)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:46 +0000 (13:16 +0200)]
NFC: st21nfcb: Fix st21nfcb_nci_close
When closing st21nfcb driver, flag ST21NFCB_NCI_RUNNING can be cleared
only once the ndlc and the transport (i2c or spi) layers are released.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:45 +0000 (13:16 +0200)]
NFC: st21nfcb: Add ndlc_close in st21nfcb_nci_remove
In order to release the st21nfcb properly close the ndlc
layer first.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:44 +0000 (13:16 +0200)]
NFC: st21nfcb: remove st21nfcb_nci_i2c_disable
ndlc_remove already calls st21nfcb_nci_i2c_disable and
phy->powered is already set to 0.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:43 +0000 (13:16 +0200)]
NFC: st21nfcb: Do not remove header once the payload is sent
Once the data is sent, we need to preserve the full frame for
the ndlc state machine. If the NDLC ACK is not received in time,
the ndlc layer will resend the same frame.
Having the header byte pulled will corrupt the frame.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Firo Yang [Sat, 6 Jun 2015 11:16:42 +0000 (13:16 +0200)]
NFC: st21nfcb: Remove inappropriate kfree on a devm_kzalloc pointer
Since ndev->driver_data is allocated by devm_kzalloc(), we do not
need the inappropriate kfree to free it in driver's remove function.
Freeing will trigger when driver unloads.
Cc: stable@vger.kernel.org
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:41 +0000 (13:16 +0200)]
NFC: nci: Add nci_prop_cmd allowing to send proprietary nci cmd
Handle allowing to send proprietary nci commands anywhere in the nci
state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:40 +0000 (13:16 +0200)]
NFC: nci: Add nci init ops for early device initialization
Some device may need to execute some proprietary commands
in order to "wake-up"; Before the nci state initialization.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sat, 6 Jun 2015 11:16:39 +0000 (13:16 +0200)]
NFC: nci: Add NCI_RESET return code check before setup
setup was executed in any case, even if NCI_RESET failed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Sat, 6 Jun 2015 11:16:37 +0000 (13:16 +0200)]
NFC: nci: Handle proprietary response and notifications
Allow for drivers to explicitly define handlers for each
proprietary notifications and responses they expect to support.
Reviewed-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Joe Perches [Mon, 1 Jun 2015 00:44:45 +0000 (17:44 -0700)]
NFC: nci: hci: Fix releasing uninitialized skbs
Several of these goto exit; uses should be direct returns
as skb is not yet initialized by nci_hci_get_param().
Miscellanea:
o Use !memcmp instead of memcmp() == 0
o Remove unnecessary goto from if () {... goto exit;} else {...} exit:
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Uwe Kleine-König [Tue, 19 May 2015 07:22:56 +0000 (09:22 +0200)]
NFC: pn544: use flags argument of devm_gpiod_get to set direction
Since
39b2bbe3d715 (gpio: add flags argument to gpiod_get*()
functions) which appeared in v3.17-rc1, the gpiod_get* functions
take an additional parameter that allows to specify direction and
initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
While touching this also do some minor coding style fixes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Tomas Winkler [Thu, 7 May 2015 13:38:30 +0000 (16:38 +0300)]
NFC: microread: drop unused variable
In microread_i2c_irq_thread_fn 'client' set but not used
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Valentin Rothberg [Tue, 28 Apr 2015 09:08:47 +0000 (11:08 +0200)]
NFC: Remove obsolete setting of DEBUG
CONFIG_DYNAMIC_DEBUG is the right toggle to enable pr_debug().
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark A. Greer [Fri, 24 Apr 2015 17:37:22 +0000 (10:37 -0700)]
NFC: trf7970a: Handle extra byte in response to Type 5 RMB commands
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Masanari Iida [Fri, 5 Jun 2015 12:38:19 +0000 (21:38 +0900)]
NFC: Fix typo in nfc-hci.txt
This patch fix a spelling typo in nfc-hci.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Thu, 28 May 2015 15:10:03 +0000 (17:10 +0200)]
NFC: nxp-nci: Fix build warning
When GPIO is not enabled we hit this kind of warning:
drivers/nfc/nxp-nci/i2c.c: In function 'nxp_nci_i2c_acpi_config':
drivers/nfc/nxp-nci/i2c.c:320:2: error: implicit declaration of function 'devm_gpiod_get_index' [-Werror=implicit-function-declaration]
gpiod_en = devm_gpiod_get_index(&client->dev, NULL, 2);
This is fixed by explicitely including gpio/consumer.h.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Oleg Zhurakivskyy [Mon, 25 May 2015 10:55:13 +0000 (13:55 +0300)]
NFC: nxp-nci_i2c: Add support for enumerating through ACPI
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Florian Fainelli [Mon, 8 Jun 2015 18:05:20 +0000 (11:05 -0700)]
net: phy: bcm7xxx: update workaround to fix 100BaseT corner cases
Update the AFE_TX_CONFIG value to solve marginal rise/fall issues
observed when the link is operating in 100BaseT. This workaround applies
to GPHY revisions D0, E0 and newer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 8 Jun 2015 07:50:49 +0000 (00:50 -0700)]
Merge branch 'phy-micrel'
Jaeden Amero says:
====================
net/phy: micrel: Center FLP timing at 16ms
In v2, we add an additional cleanup commit to make an array of strings
static const and to improve const correctness generally. We also no longer
unnecessarily initialize the result variable in
ksz9031_center_flp_timing().
In v3, we remove the unnecessary result variable from ksz9031_config_init()
introduced by a previous version of "net/phy: micrel: Center FLP timing at
16ms".
In v4, we modify the commit message of "net/phy: micrel: Center FLP timing
at 16ms" to replace the awkward quotation of the data sheet's programming
procedure with an explanation of why we program the FLP burst registers and
restart auto-negotiation where we do (config_init).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaeden Amero [Fri, 5 Jun 2015 23:00:26 +0000 (18:00 -0500)]
net/phy: micrel: Center FLP timing at 16ms
Link failures have been observed when using the KSZ9031 with HP 1810-8G
and HP 1910-8G network switches. Center the FLP timing at 16ms to help
avoid intermittent link failures.
>From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section
"Auto-Negotiation Timing":
The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst
transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3
Standard specifies this timing to be 16ms +/-8ms. Some PHY link
partners need to receive the FLP with 16ms centered timing;
otherwise, there can be intermittent link failures and long
link-up times.
The PHY data sheet recommends configuring the FLP burst registers after
power-up/reset and immediately thereafter restarting auto-negotiation, so
we center the FLP timing at 16ms and then restart auto-negotiation in the
config_init for KSZ9031.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaeden Amero [Fri, 5 Jun 2015 23:00:25 +0000 (18:00 -0500)]
net/phy: micrel: Comment MMD address of extended registers
There are some defines for a few pad skew related extended registers.
Specify for which MMD Address (dev_addr) they are for.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaeden Amero [Fri, 5 Jun 2015 23:00:24 +0000 (18:00 -0500)]
net/phy: micrel: Be more const correct
In a few places in this driver, we weren't using const where we could
have. Use const more.
In addition, change the arrays of strings in ksz9031_config_init() to be
not only const, but also static.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firo Yang [Mon, 8 Jun 2015 03:54:51 +0000 (11:54 +0800)]
fib_trie: coding style: Use pointer after check
As Alexander Duyck pointed out that:
struct tnode {
...
struct key_vector kv[1];
}
The kv[1] member of struct tnode is an arry that refernced by
a null pointer will not crash the system, like this:
struct tnode *p = NULL;
struct key_vector *kv = p->kv;
As such p->kv doesn't actually dereference anything, it is simply a
means for getting the offset to the array from the pointer p.
This patch make the code more regular to avoid making people feel
odd when they look at the code.
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicholas Mc Guire [Sun, 7 Jun 2015 10:35:46 +0000 (12:35 +0200)]
wan: dscc4: use msecs_to_jiffies for conversions
API compliance scanning with coccinelle flagged:
./drivers/net/wan/dscc4.c:1036:1-33:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:554:2-34:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:599:2-34:
WARNING: timeout (10) seems HZ dependent
Numeric constants passed to schedule_timeout_*() make the effective
timeout HZ dependent which does not seem to be the intent here.
Fixed up by converting the constant to jiffies with msecs_to_jiffies(),
passing 100ms (assuming HZ==100 in the original code).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicholas Mc Guire [Sat, 6 Jun 2015 07:51:51 +0000 (09:51 +0200)]
cosa: use msecs_to_jiffies for conversions
API compliance scanning with coccinelle flagged:
./drivers/net/wan/cosa.c:520:2-18: WARNING:
timeout (30) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which makes little sense in a device probe.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Sun, 7 Jun 2015 12:44:23 +0000 (15:44 +0300)]
net/mlx5_core: Fix static checker warnings around system guid query flow
Fix static checker warnings in the flow of system guid query.
Fixes:
707c4602cda6 ('net/mlx5_core: Add new query HCA vport commands')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vaishali Thakkar [Sat, 6 Jun 2015 01:14:00 +0000 (06:44 +0530)]
isdn/hisax: Convert use of __constant_cpu_to_le16 to cpu_to_le16
In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Murdaca [Fri, 5 Jun 2015 16:58:38 +0000 (18:58 +0200)]
ethernet: micrel: use time_is_before_eq_jiffies
use time_is_before_eq_jiffies macro for time comparison
Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fugang Duan [Fri, 5 Jun 2015 09:22:08 +0000 (17:22 +0800)]
net: fec: ptp: correct the ENET_ATCOR value
The current driver adjust freq formula is:
fe * diff = ppb * pc
Note:
fe: ENET ref clock frequency in Hz
diff = inc_corr - inc: difference between default increment and correction increment
ppb: parts per billion adjustment from base
pc: correction period (in number of fe clock cycles)
The correction increment will be used after N cycles of regular increments,
not every N cycles (with N being the correction period). For example, set ENET_ATCOR=4,
INC=8, INC_CORR=9, there will be 4 increments of 8 (ENET_ATINC[INC]) , followed by 1
increment of 9 (ENET_ATINC[INC_CORR]).
So, the correct formula is:
fe * diff = ppb * (pc + 1)
For ENET_ATCOR, a value 0 disables the correction counter and no corrections occur.
So base on the origin formula, set pc = pc > 1 ? pc - 1 : pc.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Simek [Fri, 5 Jun 2015 08:49:17 +0000 (10:49 +0200)]
net: ll_temac: Remove sparse warnings
Remove sparse warnings:
drivers/net/ethernet/xilinx/ll_temac_main.c:65:16: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:70:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:127:16: warning: cast
removes address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:137:9: warning: cast removes
address space of expression
drivers/net/ethernet/xilinx/ll_temac_main.c:409:3: warning: symbol
'temac_options' was not declared. Should it be static?
drivers/net/ethernet/xilinx/ll_temac_main.c:590:6: warning: symbol
'temac_adjust_link' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 5 Jun 2015 01:30:43 +0000 (18:30 -0700)]
tcp: get_cookie_sock() consolidation
IPv4 and IPv6 share same implementation of get_cookie_sock(),
and there is no point inlining it.
We add tcp_ prefix to the common helper name and export it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 4 Jun 2015 23:15:50 +0000 (16:15 -0700)]
net: bcmgenet: improve TX timeout
Dump useful ring statistics along with interrupt status, software
maintained pointers and hardware registers to help troubleshoot TX queue
stalls.
When a timeout occurs, disable TX NAPI for the rings, dump their states
while interrupts are disabled, re-enable interrupts, NAPI and queue flow
control to help with the recovery.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 4 Jun 2015 23:10:09 +0000 (01:10 +0200)]
net: dsa: mv88e6xxx: Fix deadlock by double lock
ethtool -S on a DSA interface can deadlock for some switches because
the same lock is taken twice. Use the register read function which
expects the lock to be already held.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes:
31888234b736 ("net: dsa: mv88e6xxx: Replace stats mutex with SMI mutex")
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Thu, 4 Jun 2015 17:11:54 +0000 (10:11 -0700)]
bpf: allow programs to write to certain skb fields
allow programs read/write skb->mark, tc_index fields and
((struct qdisc_skb_cb *)cb)->data.
mark and tc_index are generically useful in TC.
cb[0]-cb[4] are primarily used to pass arguments from one
program to another called via bpf_tail_call() which can
be seen in sockex3_kern.c example.
All fields of 'struct __sk_buff' are readable to socket and tc_cls_act progs.
mark, tc_index are writeable from tc_cls_act only.
cb[0]-cb[4] are writeable by both sockets and tc_cls_act.
Add verifier tests and improve sample code.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Thu, 4 Jun 2015 17:11:53 +0000 (10:11 -0700)]
bpf: make programs see skb->data == L2 for ingress and egress
eBPF programs attached to ingress and egress qdiscs see inconsistent skb->data.
For ingress L2 header is already pulled, whereas for egress it's present.
This is known to program writers which are currently forced to use
BPF_LL_OFF workaround.
Since programs don't change skb internal pointers it is safe to do
pull/push right around invocation of the program and earlier taps and
later pt->func() will not be affected.
Multiple taps via packet_rcv(), tpacket_rcv() are doing the same trick
around run_filter/BPF_PROG_RUN even if skb_shared.
This fix finally allows programs to use optimized LD_ABS/IND instructions
without BPF_LL_OFF for higher performance.
tc ingress + cls_bpf + samples/bpf/tcbpf1_kern.o
w/o JIT w/JIT
before 20.5 23.6 Mpps
after 21.8 26.6 Mpps
Old programs with BPF_LL_OFF will still work as-is.
We can now undo most of the earlier workaround commit:
a166151cbe33 ("bpf: fix bpf helpers to use skb->mac_header relative offsets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 4 Jun 2015 15:01:12 +0000 (08:01 -0700)]
tcp: remove redundant checks II
For same reasons than in commit
12e25e1041d0 ("tcp: remove redundant
checks"), we can remove redundant checks done for timewait sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 5 Jun 2015 18:19:11 +0000 (19:19 +0100)]
fddi: print an address with %p format specifier rather than %x
The debug is printing the struct smt_header * address using
the %x format specifier. Fix it to use %p instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicholas Mc Guire [Sat, 6 Jun 2015 08:41:17 +0000 (10:41 +0200)]
wan: dscc4: fix build warning Wunused-but-set-variable
Fix:
drivers/net/wan/dscc4.c: In function 'dscc4_open':
drivers/net/wan/dscc4.c:1049:25: warning: variable 'ppriv' set but not used
[-Wunused-but-set-variable]
This has been in there unused since
1da177e4c3f (Linux-2.6.12-rc2) simply
remove it.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 7 Jun 2015 04:17:57 +0000 (21:17 -0700)]
inet: add IP_BIND_ADDRESS_NO_PORT to overcome bind(0) limitations
When an application needs to force a source IP on an active TCP socket
it has to use bind(IP, port=x).
As most applications do not want to deal with already used ports, x is
often set to 0, meaning the kernel is in charge to find an available
port.
But kernel does not know yet if this socket is going to be a listener or
be connected.
It has very limited choices (no full knowledge of final 4-tuple for a
connect())
With limited ephemeral port range (about 32K ports), it is very easy to
fill the space.
This patch adds a new SOL_IP socket option, asking kernel to ignore
the 0 port provided by application in bind(IP, port=0) and only
remember the given IP address.
The port will be automatically chosen at connect() time, in a way
that allows sharing a source port as long as the 4-tuples are unique.
This new feature is available for both IPv4 and IPv6 (Thanks Neal)
Tested:
Wrote a test program and checked its behavior on IPv4 and IPv6.
strace(1) shows sequences of bind(IP=127.0.0.2, port=0) followed by
connect().
Also getsockname() show that the port is still 0 right after bind()
but properly allocated after connect().
socket(PF_INET, SOCK_STREAM, IPPROTO_IP) = 5
setsockopt(5, SOL_IP, IP_BIND_ADDRESS_NO_PORT, [1], 4) = 0
bind(5, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("127.0.0.2")}, 16) = 0
getsockname(5, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("127.0.0.2")}, [16]) = 0
connect(5, {sa_family=AF_INET, sin_port=htons(53174), sin_addr=inet_addr("127.0.0.3")}, 16) = 0
getsockname(5, {sa_family=AF_INET, sin_port=htons(38050), sin_addr=inet_addr("127.0.0.2")}, [16]) = 0
IPv6 test :
socket(PF_INET6, SOCK_STREAM, IPPROTO_IP) = 7
setsockopt(7, SOL_IP, IP_BIND_ADDRESS_NO_PORT, [1], 4) = 0
bind(7, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 0
getsockname(7, {sa_family=AF_INET6, sin6_port=htons(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, [28]) = 0
connect(7, {sa_family=AF_INET6, sin6_port=htons(57300), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, 28) = 0
getsockname(7, {sa_family=AF_INET6, sin6_port=htons(60964), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_flowinfo=0, sin6_scope_id=0}, [28]) = 0
I was able to bind()/connect() a million concurrent IPv4 sockets,
instead of ~32000 before patch.
lpaa23:~# ulimit -n
1000010
lpaa23:~# ./bind --connect --num-flows=
1000000 &
1000000 sockets
lpaa23:~# grep TCP /proc/net/sockstat
TCP: inuse
2000063 orphan 0 tw 47 alloc
2000157 mem 66
Check that a given source port is indeed used by many different
connections :
lpaa23:~# ss -t src :40000 | head -10
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 0 127.0.0.2:40000 127.0.202.33:44983
ESTAB 0 0 127.0.0.2:40000 127.2.27.240:44983
ESTAB 0 0 127.0.0.2:40000 127.2.98.5:44983
ESTAB 0 0 127.0.0.2:40000 127.0.124.196:44983
ESTAB 0 0 127.0.0.2:40000 127.2.139.38:44983
ESTAB 0 0 127.0.0.2:40000 127.1.59.80:44983
ESTAB 0 0 127.0.0.2:40000 127.3.6.228:44983
ESTAB 0 0 127.0.0.2:40000 127.0.38.53:44983
ESTAB 0 0 127.0.0.2:40000 127.1.197.10:44983
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Jun 2015 09:06:33 +0000 (14:36 +0530)]
cxgb4: Fix static checker warning
The patch
e85c9a7abfa4: ("cxgb4/cxgb4vf: Add code to calculate T5 BAR2
Offsets for SGE Queue Registers") from Dec 3, 2014, leads to the
following static checker warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5358
t4_bar2_sge_qregs()
warn: should '(qid >> qpp_shift) << page_shift' be a 64 bit type?
This patch fixes it
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 6 Jun 2015 04:26:07 +0000 (21:26 -0700)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
Free VI, flush sge ec and some other misc. fixes
This patch series adds the following.
Free VI interface during remove, flush SGE ec routine, rename
t4_link_start to t4_link_l1cfg since it only does l1 configuration, set
mac addr from when we can't contact firmware for debug purpose, set pcie
completion timeout and use fw interface to access TP_PIO_XXX registers
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Jun 2015 08:54:52 +0000 (14:24 +0530)]
cxgb4: Use FW LDST cmd to access TP_PIO_{ADDR, DATA} register first
The TP_PIO_{ADDR,DATA} registers are are in conflict with the firmware's
use of these registers. Added a routine to access it through FW LDST
cmd.
Access all TP_PIO_{ADDR,DATA} register access through new routine if FW
is alive. If firmware is dead, than fall back to indirect access.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Jun 2015 08:54:51 +0000 (14:24 +0530)]
cxgb4: program pci completion timeout
Set pci completion timeout to 0xd.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Jun 2015 08:54:50 +0000 (14:24 +0530)]
cxgb4: Set mac addr from vpd, when we can't contact firmware
Grab the Adapter MAC Address out of the VPD and use it for the "debug"
network interface when either we can't contact the firmware
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Jun 2015 08:54:49 +0000 (14:24 +0530)]
cxgb4: Rename t4_link_start() to t4_link_l1cfg
t4_link_start() was completely misnamed. It does _not_ start up the
link. It merely does the L1 Configuration for the link. The Link Up
process is started automatically by the firmware when the number of
enabled Virtual Interfaces on a port goes from 0 to 1. So renaming
this routine to t4_link_l1cfg() for better documentation.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Jun 2015 08:54:48 +0000 (14:24 +0530)]
cxgb4: Add sge ec context flush service
Add function to flush the sge ec context cache, and utilize
this new function in the driver
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Fri, 5 Jun 2015 08:54:47 +0000 (14:24 +0530)]
cxgb4: Free Virtual Interfaces in remove routine
Free VI interfaces in remove routine. If we don't do this then the
firmware will never drop the physical link to the peer.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 23:41:02 +0000 (16:41 -0700)]
Merge branch 'mlx5-next'
Or Gerlitz says:
====================
mlx5: Add Interface Step Sequence ID support
ISSI (Interface Step Sequence ID) defines the step sequence ID of the
interface between the driver to the firmware and is incremented by
steps of one. ISSI is used to enable deprecating/modifying features,
command interfaces and such, while maintaining compatibility.
As the driver serves both ConnectIB (CIB) and ConnectX4, we carefully
made sure that the IB functionality keeps running also on older CIB
firmware releases that don't support ISSI.
The Ethernet functionailty is available only on ConnectX4 where all
firmware releases support the feature since the very basic ISSI level.
So at this point no need for compatility code there.
As done prior to this series, when the Ethernet functionlity is enabled,
during the initialization flow, the core driver performs a query of the
supported ISSIs using the QUERY_ISSI command, and then, if ISSI is supported,
sets the actual issi value informing the firmware on which ISSI level to run,
using SET_ISSI command.
Previously, the IB driver wasn't ready to work on that mode, and hence
building both the IB driver and the Ethernet functionality in the core
driver were disallowed by Kconfigs, with this series, we allow users to
enable them both.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Haggai Abramonvsky [Thu, 4 Jun 2015 16:30:48 +0000 (19:30 +0300)]
mlx5: Enable mutual support for IB and Ethernet
Ethernet functionality is only available when working in ISSI > 0 mode.
Previously, the IB driver wasn't ready to work on that mode, and hence
building both the IB driver and the Ethernet functionality in the core
driver were disallowed by Kconfigs.
Now, once we have all the pre-steps in place, we can remove this limitation.
The last steps in the IB driver for getting that setup to work are:
create dummy SRQ for the driver's use (until now we could use XRC_SRQ
as SRQ and XRC_SRQ, after moving to ISSI > 0, we separate XRC SRQs from
basic SRQs) and adapt the create QP function to be compatible with ISSI > 0.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:47 +0000 (19:30 +0300)]
IB/mlx5: Don't create IB instance over Ethernet ports
Since we still don't have RoCE support in mlx5, avoid
creating IB driver instance over Ethernet ports.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:46 +0000 (19:30 +0300)]
IB/mlx5: Avoid using the MAD_IFC command under ISSI > 0 mode
In ISSI > 0 mode, most of the MAD_IFC command features are deprecated, and can't
be used. Therefore, when in that mode, we replace all of them with other commands
that provide the required functionality.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:45 +0000 (19:30 +0300)]
net/mlx5_core: Add more query port helpers
Add the following helpers:
1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port
These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:44 +0000 (19:30 +0300)]
net/mlx5_core: Use port number when querying port ptys
Until now, mlx5_query_port_ptys always queried port number one.
Added new argument in the function's prototype so we can also query
the second port. This will be needed when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:43 +0000 (19:30 +0300)]
net/mlx5_core: Use port number in the query port mtu helpers
Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:42 +0000 (19:30 +0300)]
net/mlx5_core: Get vendor-id using the query adapter command
Add two wrapper functions to the query adapter command:
1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.
2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
query_adapter command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:41 +0000 (19:30 +0300)]
net/mlx5_core: Add new query HCA vport commands
Added the implementation for the following commands:
1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT
They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Majd Dibbiny [Thu, 4 Jun 2015 16:30:40 +0000 (19:30 +0300)]
net/mlx5_core: Make the vport helpers available for the IB driver too
Move the vport header file to be under include/linux/mlx5, such that
the mlx5 IB can use it as well.
Also add nic_ prefix to the vport NIC commands to differeniate between
HCA vport commands and NIC vport commands.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haggai Abramonvsky [Thu, 4 Jun 2015 16:30:39 +0000 (19:30 +0300)]
net/mlx5_core: Check the return bitmask when querying ISSI
The determination of the supported ISSI versions should be conditioned
on the returned mask, and not only on the return status of the query
ISSI command, fix that.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haggai Abramonvsky [Thu, 4 Jun 2015 16:30:38 +0000 (19:30 +0300)]
net/mlx5_core: Enable XRCs and SRQs when using ISSI > 0
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haggai Abramonvsky [Thu, 4 Jun 2015 16:30:37 +0000 (19:30 +0300)]
net/mlx5_core: Apply proper name convention to helpers
Some core helper functions were named with mlx5_ only prefix, fix that to
mlx5_core_ so we're aligned with the overall scheme used for core services.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Thu, 4 Jun 2015 16:30:36 +0000 (19:30 +0300)]
net/mlx5_en: Add missing check for memory allocation failure
The patch
afb736e9330a: "net/mlx5: Ethernet resource handling files"
from May 28, 2015, leads to the following static checker warning:
drivers/net/ethernet/mellanox/mlx5/core/en_flow_table.c:726 mlx5e_create_main_flow_table()
error: potential null dereference 'g'. (kcalloc returns null)
Fixes:
afb736e9330a ("net/mlx5: Ethernet resource handling files")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 22:44:32 +0000 (15:44 -0700)]
Merge branch 'flow_key_hashing'
Tom Herbert says:
====================
net: Increase inputs to flow_keys hashing
This patch set adds new fields to the flow_keys structure and hashes
over these fields to get a better flow hash. In particular, these
patches now include hashing over the full IPv6 addresses in order
to defend against address spoofing that always results in the
same hash. The new input also includes the Ethertype, L4 protocol,
VLAN, flow label, GRE keyid, and MPLS entropy label.
In order to increase hash inputs, we switch to using jhash2
which operates an an array of u32's. jhash2 operates on multiples of
three words. The data in the hash is constructed for that, and there
are are two variants for IPv4 and Ipv6 addressing. For IPv4 addresses,
jhash is performed over six u32's and for IPv6 it is done over twelve.
flow_keys can store either IPv4 or IPv6 addresses (addr_proto field
is a selector). ipv6_addr_hash is no longer used to convert addresses
for setting in flow table. For legacy uses of flow keys outside of
flow_dissector the flow_get_u32_src and flow_get_u32_dst functions
have been added to get u32 representation representations of addresses
in flow_keys.
For flow lables we also eliminate the short circuit in flow_dissector
for non-zero flow label. The flow label is now considered additional
input to ports.
Testing: Ran netperf TCP_RR for 200 flows using IPv4 and IPv6 comparing
before the patches and with the patches. Did not detect any performance
degradation.
v2:
- Took out MPLS entropy label. Will add this later.
v3:
- Ensure hash start offset is a four byte boundary. Add BUG_BUILD_ON
to check for this.
- Fixes sparse error in GRE to get entropy from keyid.
v4:
- Rebase to Jiri changes to generalize flow dissection
- Support TIPC as its own address
- Bring back MPLS entropy label dissection
- Remove FLOW_DISSECTOR_KEY_IPV6_HASH_ADDRS
v5:
- Minor fixes from feedback
v6:
- Cleanup and sparse issue with flow label
- Change keyid to returned by flow_dissector to be __be32
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:46 +0000 (09:16 -0700)]
mpls: Add MPLS entropy label in flow_keys
In flow dissector if an MPLS header contains an entropy label this is
saved in the new keyid field of flow_keys. The entropy label is
then represented in the flow hash function input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:45 +0000 (09:16 -0700)]
net: Add GRE keyid in flow_keys
In flow dissector if a GRE header contains a keyid this is saved in the
new keyid field of flow_keys. The GRE keyid is then represented
in the flow hash function input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:44 +0000 (09:16 -0700)]
net: Add IPv6 flow label to flow_keys
In flow_dissector set the flow label in flow_keys for IPv6. This also
removes the shortcircuiting of flow dissection when a non-zero label
is present, the flow label can be considered to provide additional
entropy for a hash.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:43 +0000 (09:16 -0700)]
net: Add VLAN ID to flow_keys
In flow_dissector set vlan_id in flow_keys when VLAN is found.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:42 +0000 (09:16 -0700)]
net: Get rid of IPv6 hash addresses flow keys
We don't need to return the IPv6 address hash as part of flow keys.
In general, using the IPv6 address hash is risky in a hash value
since the underlying use of xor provides no entropy. If someone
really needs the hash value they can get it from the full IPv6
addresses in flow keys (e.g. from flow_get_u32_src).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:41 +0000 (09:16 -0700)]
net: Add keys for TIPC address
Add a new flow key for TIPC addresses.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:40 +0000 (09:16 -0700)]
net: Add full IPv6 addresses to flow_keys
This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.
We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.
With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:39 +0000 (09:16 -0700)]
net: Get skb hash over flow_keys structure
This patch changes flow hashing to use jhash2 over the flow_keys
structure instead just doing jhash_3words over src, dst, and ports.
This method will allow us take more input into the hashing function
so that we can include full IPv6 addresses, VLAN, flow labels etc.
without needing to resort to xor'ing which makes for a poor hash.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:38 +0000 (09:16 -0700)]
net: Remove superfluous setting of key_basic
key_basic is set twice in __skb_flow_dissect which seems unnecessary.
Remove second one.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:37 +0000 (09:16 -0700)]
mpls: Add definition for IPPROTO_MPLS
Add uapi define for MPLS over IP.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 4 Jun 2015 16:16:36 +0000 (09:16 -0700)]
net: Simplify GRE case in flow_dissector
Do break when we see routing flag or a non-zero version number in GRE
header.
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shailendra Verma [Thu, 4 Jun 2015 14:41:00 +0000 (20:11 +0530)]
atm:he - Do not initialise statics to 0.
According to <stdbool.h> false is always '0' and
Static variables are initialised to 0 by GCC.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Thu, 4 Jun 2015 15:33:48 +0000 (08:33 -0700)]
bpf: fix build due to missing tc_verd
fix build error:
net/core/filter.c: In function 'bpf_clone_redirect':
net/core/filter.c:1429:18: error: 'struct sk_buff' has no member named 'tc_verd'
if (G_TC_AT(skb2->tc_verd) & AT_INGRESS)
Fixes:
3896d655f4d4 ("bpf: introduce bpf_clone_redirect() helper")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Liu [Wed, 3 Jun 2015 10:10:42 +0000 (11:10 +0100)]
tcp: double default TSQ output bytes limit
Xen virtual network driver has higher latency than a physical NIC.
Having only 128K as limit for TSQ introduced 30% regression in guest
throughput.
This patch raises the limit to 256K. This reduces the regression to 8%.
This buys us more time to work out a proper solution in the long run.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 4 Jun 2015 06:49:21 +0000 (23:49 -0700)]
tcp: remove redundant checks
tcp_v4_rcv() checks the following before calling tcp_v4_do_rcv():
if (th->doff < sizeof(struct tcphdr) / 4)
goto bad_packet;
if (!pskb_may_pull(skb, th->doff * 4))
goto discard_it;
So following check in tcp_v4_do_rcv() is redundant
and "goto csum_err;" is wrong anyway.
if (skb->len < tcp_hdrlen(skb) || ...)
goto csum_err;
A second check can be removed after no_tcp_socket label for same reason.
Same tests can be removed in tcp_v6_do_rcv()
Note : short tcp frames are not properly accounted in tcpInErrs MIB,
because pskb_may_pull() failure simply drops incoming skb, we might
fix this in a separate patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 06:47:24 +0000 (23:47 -0700)]
Merge branch 'switchdev-next'
Scott Feldman says:
====================
switchdev: documentation updates
Update the switchdev documentation to clarify that for IPV4 FIB object, the add
op is used for both adding and modifying the FIB entry on the device.
I found a few other white-space and grammer issues to fix, and to clarify the
static FDB ops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 4 Jun 2015 03:43:43 +0000 (20:43 -0700)]
switchdev: documentation: use switchdev_port_obj_xxx for IPv4 FIB add/modify/delete ops
Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.
Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 4 Jun 2015 03:43:42 +0000 (20:43 -0700)]
switchdev: documentation: for static FDB ops, use switchdev_port_fdb_xxx ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 4 Jun 2015 03:43:41 +0000 (20:43 -0700)]
switchdev: documentation: fix grammer error
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 4 Jun 2015 03:43:40 +0000 (20:43 -0700)]
switchdev: documentation: fix longer-than-80-char lines
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 06:44:57 +0000 (23:44 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================
Conflicts:
drivers/net/wireless/iwlwifi/Kconfig
Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 06:40:20 +0000 (23:40 -0700)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
cxgb4: Adds support for various ethtool stats
This patch series adds the following:
Adds support to dump adapter specific stats in ethtool
Adds support to dump channel stats in ethtool
Adds support to dump loopback port stats in ethtool
Remove wake-on-lan get/set ethtool support
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:42 +0000 (21:04 +0530)]
cxgb4: Remove WOL get/set ethtool support
Remove ethtool get/set support for wake on lan, adapter doesn't support
it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:41 +0000 (21:04 +0530)]
cxgb4: Add support to dump loopback port stats
Add support in ethtool to dump loopback port statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:40 +0000 (21:04 +0530)]
cxgb4: Add support in ethtool to dump channel stats
Add support in ethtool to dump adapter channel stats
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 3 Jun 2015 15:34:39 +0000 (21:04 +0530)]
cxgb4: Add ethtool support to get adapter stats
Add ethtool support to get adapter specific hardware statistics
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 03:22:46 +0000 (20:22 -0700)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
pull request: batman-adv
20150603
here you have our second batch of patches intended for net-next.
In this patchset you won't find any new features, but quite some code
cleanup work, a bunch of code style fixes and also comments corrections
by Markus Pargmann.
Moreover you have a patch from Sven Eckelmann removing an unnecessary
NULL check in batadv_iv_ogm_update_seqnos().
Please pull or let me know of any problem!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rasmus Villemoes [Wed, 3 Jun 2015 11:44:03 +0000 (13:44 +0200)]
net: tulip: rearrange order of searching for substrings
Currently, two of the branches are dead code, since an earlier smaller
substring would have been found ("TP" in the "TP_NW" case and either
of "BNC" and "AUI" in the "BNC_AUI" case). Rearrange the strstr()
calls so that the longer strings are searched for first.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 03:19:16 +0000 (20:19 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-06-03
This series contains updates to e1000e only.
Yanir provides 8 fixes and 1 version bump for e1000e. First fix resolves
a possible unit hang if multiple descriptors are available in the rings
during reset or runtime suspend. Fixed a warning on SPARC compile based
on a suggested solution from Alex Duyck. Fixed a logical error, where
a "if" condition under which a flush should occur, was revered. Fixed
a hardware issue that prevented i219 from working in legacy interrupts
mode. Fixed the hardware clock configuration and suprious non-linear
increment. Lastly, fixed a system hang which occurred during execution
of "ethtool -t <NIC>", by disabling MULR for the loopback test to avoid
the hand state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Tue, 2 Jun 2015 23:03:14 +0000 (16:03 -0700)]
bpf: introduce bpf_clone_redirect() helper
Allow eBPF programs attached to classifier/actions to call
bpf_clone_redirect(skb, ifindex, flags) helper which will
mirror or redirect the packet by dynamic ifindex selection
from within the program to a target device either at ingress
or at egress. Can be used for various scenarios, for example,
to load balance skbs into veths, split parts of the traffic
to local taps, etc.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carol Soto [Tue, 2 Jun 2015 21:07:25 +0000 (16:07 -0500)]
net/mlx4_core: fix typo in mlx4_set_vf_mac
fix typo in mlx4_set_vf_mac
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>