OSDN Git Service
José Roberto de Souza [Wed, 4 Sep 2019 21:34:15 +0000 (14:34 -0700)]
drm/i915/tgl: Access the right register when handling PSR interruptions
For older gens PSR IIR and IMR have fixed addresses. From TGL onwards those
registers moved to each transcoder offset. The bits for the registers
are defined without an offset per transcoder as right now we have one
register per transcoder. So add a fake "trans_shift" when calculating
the bits offsets: it will be 0 for gen12+ and psr.transcoder otherwise.
v2 (Lucas): change the implementation to use trans_shift instead of
getting each bit value with a different macro
Cc: Imre Deak <imre.deak@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904213419.27547-3-jose.souza@intel.com
José Roberto de Souza [Wed, 4 Sep 2019 21:34:14 +0000 (14:34 -0700)]
drm/i915/psr: Only handle interruptions of the transcoder in use
It was enabling and checking PSR interruptions in every transcoder
while it should keep the interruptions on the non-used transcoders
masked.
While doing this it gives us trouble on Tiger Lake if we are
reading/writing to registers of disabled transcoders since from gen12
onwards the registers are relative to the transcoder. Instead of forcing
them ON to access those registers, just avoid the accesses as they are
not needed.
v2 (Lucas):
- Explain why we can't keep accessing all transcoders
- Remove TODO about extending the irq handling to multiple instances:
when/if implementing multiple instances it's pretty clear by the
singleton psr that it needs to be extended
- Fix intel_psr_debug_set() calling psr_irq_control() with
psr.transcoder not set yet (from Imre). Now we only set the debug
register right away if psr is already enabled. Otherwise we just
record the value to be set when enabling the source.
- Do not depend on the value of TRANSCODER_A. Just be relative to it
(from Imre)
- handle psr error last so we don't schedule the work before handling
the other flags
v3:
- Adding a warning about setting reserverd bits on EDP_PSR_IMR
Cc: Imre Deak <imre.deak@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904213419.27547-2-jose.souza@intel.com
Daniel Vetter [Tue, 20 Aug 2019 19:54:51 +0000 (21:54 +0200)]
drm/i915: disable set/get_tiling ioctl on gen12+
The cpu (de)tiler hw is gone, this stopped being useful. Plus it never
supported any of the fancy new tiling formats, which means userspace
also stopped using the magic side-channel this provides.
This would totally break a lot of the igts, but they're already broken
for the same reasons as userspace on gen12 would be.
v2: Look at ggtt->num_fences instead, that also avoids the need for a
comment (Chris). This also means that gen12 support really needs to
make sure num_fences is set to 0. There is a patch for that, but it
checks for HAS_MAPPABLE_APERTURE, which I'm not sure is the right
thing really. Adding relevant people.
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Stuart Summers <stuart.summers@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820195451.15671-1-daniel.vetter@ffwll.ch
Ville Syrjälä [Tue, 3 Sep 2019 15:40:18 +0000 (18:40 +0300)]
Revert "drm/i915: Fix DP-MST crtc_mask"
This reverts commit
4eaceea3a00f8e936a7f48dcd0c975a57f88930f.
Several userspace clients (modesetting ddx and mutter+wayland at least)
handle encoder.possible_crtcs incorrectly. What they essentially do is
the following:
possible_crtcs = ~0;
for_each_possible_encoder(connector)
possible_crtcs &= encoder->possible_crtcs;
Ie. they calculate the intersection of the possible_crtcs
for the connector when they really should be calculating the
union instead.
In our case each MST encoder now has just one unique bit set,
and so the intersection is always zero. The end result is that
MST connectors can't be lit up because no crtc can be found to
drive them.
I've submitted a fix for the modesetting ddx [1], and complained
on #wayland about mutter, so hopefully the situation will improve
in the future. In the meantime we have regression, and so must go
back to the old way of misconfiguring possible_crtcs in the kernel.
[1] https://gitlab.freedesktop.org/xorg/xserver/merge_requests/277
Cc: Jonas Ådahl <jadahl@gmail.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111507
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190903154018.26357-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Chris Wilson [Wed, 4 Sep 2019 10:07:07 +0000 (11:07 +0100)]
drm/i915: Restore relaxed padding (OCL_OOB_SUPPRES_ENABLE) for skl+
This bit was fliped on for "syncing dependencies between camera and
graphics". BSpec has no recollection why, and it is causing
unrecoverable GPU hangs with Vulkan compute workloads.
From BSpec, setting bit5 to 0 enables relaxed padding requirements for
buffers, 1D and 2D non-array, non-MSAA, non-mip-mapped linear surfaces;
and *must* be set to 0h on skl+ to ensure "Out of Bounds" case is
suppressed.
Reported-by: Jason Ekstrand <jason@jlekstrand.net>
Suggested-by: Jason Ekstrand <jason@jlekstrand.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110998
Fixes:
8424171e135c ("drm/i915/gen9: h/w w/a: syncing dependencies between camera and graphics")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: denys.kostin@globallogic.com
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.1+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904100707.7377-1-chris@chris-wilson.co.uk
Swati Sharma [Tue, 3 Sep 2019 19:22:57 +0000 (00:52 +0530)]
drm/i915/display: Extract glk_read_luts()
For glk, add hw read out to create hw blob of gamma
lut values.
v4: -No need to initialize *blob [Jani]
-Removed right shifts [Jani]
-Dropped dev local var [Jani]
v5: -Returned blob instead of assigning it internally within the
function [Ville]
-Renamed glk_get_color_config() to glk_read_luts() [Ville]
-Added degamma validation [Ville]
v9: -80 character limit [Uma]
-Made read func para as const [Ville, Uma]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-8-git-send-email-swati2.sharma@intel.com
Swati Sharma [Tue, 3 Sep 2019 19:22:56 +0000 (00:52 +0530)]
drm/i915/display: Extract ilk_read_luts()
For ilk, add hw read out to create hw blob of gamma
lut values.
v4: -No need to initialize *blob [Jani]
-Removed right shifts [Jani]
-Dropped dev local var [Jani]
v5: -Returned blob instead of assigning it internally within the
function [Ville]
-Renamed ilk_get_color_config() to ilk_read_luts() [Ville]
v9: -80 character limit [Uma]
-Made read func para as const [Ville, Uma]
-Renamed ilk_read_gamma_lut() to ilk_read_lut_10() [Uma, Ville]
v10: -Made ilk_read_luts() static [Jani]
-ilk_load_lut_10 has lut_size, not (lut_size - 1) [Jani]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-7-git-send-email-swati2.sharma@intel.com
Swati Sharma [Tue, 3 Sep 2019 19:22:55 +0000 (00:52 +0530)]
drm/i915/display: Extract i9xx_read_luts()
For the legacy(gen < 4) gamma, add hw read out to create hw blob of gamma
lut values. Also, add function intel_color_lut_pack to convert hw value
with given bit precision to lut property val.
v4: -No need to initialize *blob [Jani]
-Removed right shifts [Jani]
-Dropped dev local var [Jani]
v5: -Returned blob instead of assigning it internally within the
function [Ville]
-Renamed function i9xx_get_color_config() to i9xx_read_luts()
-Renamed i9xx_get_config_internal() to i9xx_read_lut_8() [Ville]
v9: -Change in commit message [Jani, Uma]
-Wrap commit within 75 characters [Uma]
-Use macro for 256 [Uma]
-Made read func para as const [Ville, Uma]
v10: -Made i9xx_read_luts() static [Jani]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-6-git-send-email-swati2.sharma@intel.com
Swati Sharma [Tue, 3 Sep 2019 19:22:54 +0000 (00:52 +0530)]
drm/i915/display: Add macro to compare gamma hw/sw lut
Add macro to compare hw/sw gamma lut values. First need to
check whether hw/sw gamma mode matches or not. If not
no need to compare lut values, if matches then only compare
lut entries.
v5: -Called PIPE_CONF_CHECK_COLOR_LUT inside if (!adjust) [Jani]
-Added #undef PIPE_CONF_CHECK_COLOR_LUT [Jani]
v8: -Added check for gamma mode before gamma lut entry comparison
[Jani]
-Split patch 3 into 4 patches
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-5-git-send-email-swati2.sharma@intel.com
Swati Sharma [Tue, 3 Sep 2019 19:22:53 +0000 (00:52 +0530)]
drm/i915/display: Add func to compare hw/sw gamma lut
Add func intel_color_lut_equal() to compare hw/sw gamma
lut values. Since hw/sw gamma lut sizes and lut entries comparison
will be different for different gamma modes, add gamma mode dependent
checks.
v3: -Rebase
v4: -Renamed intel_compare_color_lut() to intel_color_lut_equal() [Jani]
-Added the default label above the correct label [Jani]
-Corrected smatch warn "variable dereferenced before check"
[Dan Carpenter]
v5: -Added condition (!blob1 && !blob2) return true [Jani]
v6: -Made patch11 as patch3 [Jani]
v8: -Split patch 3 into 4 patches
-Optimized blob check condition [Ville]
v9: -Exclude spilt gamma mode (bdw and ivb platforms)
as there is exception in way gamma values are written in
hardware [Ville]
-Added exception made in commit [Uma]
-Dropped else, character limit and indentation [Uma]
-Added multi segmented gama mode for icl+ platforms [Uma]
v10: -Dropped multi segmented mode for icl+ platforms [Jani]
-Removed references of sw and hw state in compare code [Jani]
-Dropped inline from func [Jani]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-4-git-send-email-swati2.sharma@intel.com
Swati Sharma [Tue, 3 Sep 2019 19:22:51 +0000 (00:52 +0530)]
drm/i915/display: Add func to get gamma bit precision
Each platform supports different gamma modes and each gamma mode
has different bit precision. Here bit precision corresponds
to number of bits the hw LUT supports.
Add func per platform to return bit precision corresponding to gamma mode
which will be later used as a parameter in lut comparison function
intel_color_lut_equal().
This is done for legacy, ilk, glk and their variant platforms.
v6: -Added func intel_color_get_bit_precision() to get bit precision for
gamma and degamma lut readout depending upon platform and
corresponding to load_luts() [Ankit]
-Made patch11 as patch3 [Jani]
v7: -Renamed func intel_color_get_bit_precision() to
intel_color_get_gamma_bit_precision()
-Added separate function/platform for gamma bit precision [Ville]
-Corrected checkpatch warnings
v8: -Split patch 3 into 4 separate patches
v9: -Changed commit message, gave more info [Uma]
-Added precision func for icl+ platform
v10: -Removed precision func for chv and icl+ platforms [Jani]
-Added gamma_enable check once [Jani]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-2-git-send-email-swati2.sharma@intel.com
Swati Sharma [Tue, 3 Sep 2019 19:22:52 +0000 (00:52 +0530)]
drm/i915/display: Add debug log for color parameters
Add debug log for color related parameters like gamma_mode, gamma_enable,
csc_enable, etc inside intel_dump_pipe_config().
v6: -Added debug log for color para in intel_dump_pipe_config [Jani]
v7: -Split patch 3 into 4 patches
v8: -Corrected alignment [Uma]
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1567538578-4489-3-git-send-email-swati2.sharma@intel.com
Chris Wilson [Mon, 2 Sep 2019 04:02:46 +0000 (05:02 +0100)]
drm/i915: Refresh the errno to vmf_fault translations
It's been a long time since we accidentally reported -EIO upon wedging,
it can now only be generated by failure to swap in a page.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Reviewed-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190902040303.14195-4-chris@chris-wilson.co.uk
Chris Wilson [Sun, 1 Sep 2019 11:04:31 +0000 (12:04 +0100)]
drm/i915/selftests: Remove unused __engines_name()
This function was never used and probably will never be used, so remove
it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190901110431.12393-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 2 Sep 2019 04:02:47 +0000 (05:02 +0100)]
drm/i915: Replace obj->pin_global with obj->frontbuffer
obj->pin_global was originally used as a means to keep the shrinker off
the active scanout, but we use the vma->pin_count itself for that and
the obj->frontbuffer to delay shrinking active framebuffers. The other
role that obj->pin_global gained was for spotting display objects inside
GEM and working harder to keep those coherent; for which we can again
simply inspect obj->frontbuffer directly.
Coming up next, we will want to manipulate the pin_global counter
outside of the principle locks, so would need to make pin_global atomic.
However, since obj->frontbuffer is already managed atomically, it makes
sense to use that the primary key for display objects instead of having
pin_global.
Ville pointed out the principle difference is that obj->frontbuffer is
set for as long as an intel_framebuffer is attached to an object, but
obj->pin_global was only raised for as long as the object was active. In
practice, this means that we consider the object as being on the scanout
for longer than is strictly required, causing us to be more proactive in
flushing -- though it should be true that we would have flushed
eventually when the back became the front, except that on the flip path
that flush is async but when hit from another ioctl it will be
synchronous.
v2: i915_gem_object_is_framebuffer()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190902040303.14195-5-chris@chris-wilson.co.uk
Chris Wilson [Mon, 2 Sep 2019 04:02:44 +0000 (05:02 +0100)]
drm/i915: Report aliasing ppgtt size as ggtt size
The aliasing-ppgtt is constrained to be the same size as the Global GTT
since it aliases the same address space. Simplifying gtt size reporting
in this case.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190902040303.14195-2-chris@chris-wilson.co.uk
Chris Wilson [Mon, 2 Sep 2019 04:02:43 +0000 (05:02 +0100)]
drm/i915: Restrict the aliasing-ppgtt to the size of the ggtt
The aliasing-ppgtt is not allowed to be smaller than the ggtt, nor
should we advertise it as being any bigger, or else we may get sued for
false advertisement.
Testcase: igt/gem_exec_big
Fixes:
0b718ba1e884 ("drm/i915/gtt: Downgrade Cherryview back to aliasing-ppgtt")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190902040303.14195-1-chris@chris-wilson.co.uk
Ville Syrjälä [Wed, 28 Aug 2019 18:34:24 +0000 (21:34 +0300)]
drm/i915: Clean up HDMI deep color handling a bit
Reogranize the HDMI deep color state computation to just
loop over possible bpc values. Avoids having to maintain
so many variants of the clock etc.
The current code also looks confused w.r.t. port_clock vs.
bw_constrained. It would happily update port_clock for
deep color but then not actually enable deep color due to
bw_constrained being set. The new logic handles that case
correctly.
v2: Pull stuff into separate funcs (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828183424.7856-1-ville.syrjala@linux.intel.com
Ville Syrjälä [Fri, 30 Aug 2019 18:27:19 +0000 (21:27 +0300)]
drm/i915: Prefer encoder->name over port_name()
enum port is a mess now because it no longer matches the spec
at all. Let's start to dig ourselves out of this hole by
reducing our reliance on port_name(). This should at least make
a bunch of debug messages a bit more sensible while we think how
to fill the the hole properly.
Based on the following cocci script with a lot of manual cleanup
(all the format strings etc.):
@@
expression E;
@@
(
- port_name(E->port)
+ E->base.base.id, E->base.name
|
- port_name(E.port)
+ E.base.base.id, E.base.name
)
@@
enum port P;
expression E;
@@
P = E->port
<...
- port_name(P)
+ E->base.base.id, E->base.name
...>
@@
enum port P;
expression E;
@@
P = E.port
<...
- port_name(P)
+ E.base.base.id, E.base.name
...>
@@
expression E;
@@
{
- enum port P = E;
... when != P
}
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830182719.32608-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 28 Aug 2019 10:20:59 +0000 (13:20 +0300)]
drm/i915: Limit MST to <= 8bpc once again
My attempt at allowing MST to use the higher color depths has
regressed some configurations. Apparently people have setups
where all MST streams will fit into the DP link with 8bpc but
won't fit with higher color depths.
What we really should be doing is reducing the bpc for all the
streams on the same link until they start to fit. But that requires
a bit more work, so in the meantime let's revert back closer to
the old behavior and limit MST to at most 8bpc.
Cc: stable@vger.kernel.org
Cc: Lyude Paul <lyude@redhat.com>
Tested-by: Geoffrey Bennett <gmux22@gmail.com>
Fixes:
f1477219869c ("drm/i915: Remove the 8bpc shackles from DP MST")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111505
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828102059.2512-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Chris Wilson [Fri, 30 Aug 2019 18:19:29 +0000 (19:19 +0100)]
drm/i915/perf: Assert locking for i915_init_oa_perf_state()
We use the context->pin_mutex to serialise updates to the OA config and
the registers values written into each new context. Document this
relationship and assert we do hold the context->pin_mutex as used by
gen8_configure_all_contexts() to serialise updates to the OA config
itself.
v2: Add a white-lie for when we call intel_gt_resume() from init.
v3: Lie while we have the context pinned inside atomic reset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20190830181929.18663-1-chris@chris-wilson.co.uk
Matt Roper [Mon, 26 Aug 2019 22:55:40 +0000 (15:55 -0700)]
drm/i915: Add 324mhz and 326.4mhz cdclks for gen11+
The bspec was recently updated with these new cdclk values for ICL, EHL,
and TGL.
Bspec: 20598
Bspec: 49201
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826225540.11987-3-matthew.d.roper@intel.com
Matt Roper [Fri, 30 Aug 2019 00:48:28 +0000 (17:48 -0700)]
drm/i915: Allow /2 CD2X divider on gen11+
The bspec has just recently been updated with new cdclk values that
require the use of a /2 CD2X divider rather than a /1 divider. Once we
add the divider selection logic to ICL+ cdclk programming, we have
pretty much the same logic we were already using on CNL, so it's simpler
to drop icl_set_cdclk() completely and reuse cnl_set_cdclk() on gen11+
platforms as well.
v2:
- Using ICL_CDCLK_CD2X_PIPE_NONE + BXT_CDCLK_CD2X_PIPE(pipe) for TGL is
correct, but looks really confusing. Add some TGL_ macros that alias
these to avoid confusion. (Ville)
- Use DIV_ROUND_CLOSEST rather than / when applying the divider. (Ville)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830004828.19359-1-matthew.d.roper@intel.com
Maarten Lankhorst [Fri, 30 Aug 2019 10:16:44 +0000 (12:16 +0200)]
drm/i915: Fix regression with crtc disable ordering
When we moved the code to disable crtc's to a separate patch,
we forgot to ensure that for_each_oldnew_intel_crtc_in_state_reverse()
was moved as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes:
66d9cec8a6c9 ("drm/i915/display: Move the commit_tail() disable sequence to separate function")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830101644.8740-1-maarten.lankhorst@linux.intel.com
Chris Wilson [Fri, 30 Aug 2019 18:03:25 +0000 (19:03 +0100)]
drm/i915: Use RCU for unlocked vm_idr lookup
Since i915_address_space is now RCU protected, we can do the vm_idr lookup
without taking the vm_idr_mutex, just with the rcu_read_lock() instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830180325.7755-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 30 Aug 2019 18:00:00 +0000 (19:00 +0100)]
drm/i915: Remove ppgtt->dirty_engines
This is no longer used anywhere and so can be removed. However, tracking
the dirty status on the ppgtt doesn't work very well if the ppgtt is
shared, so perhaps for the best that it is no longer required.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830180000.24608-3-chris@chris-wilson.co.uk
Chris Wilson [Fri, 30 Aug 2019 17:59:59 +0000 (18:59 +0100)]
drm/i915/gtt: Downgrade Cherryview back to aliasing-ppgtt
With the upcoming change in timing (dramatically reducing the latency
between manipulating the ppGTT and execution), no amount of tweaking
could save Cherryview, it would always fail to invalidate its TLB.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830180000.24608-2-chris@chris-wilson.co.uk
Chris Wilson [Fri, 30 Aug 2019 17:59:58 +0000 (18:59 +0100)]
drm/i915/gtt: Downgrade gen7 (ivb, byt, hsw) back to aliasing-ppgtt
With the upcoming change in timing (dramatically reducing the latency
between manipulating the ppGTT and execution), no amount of tweaking
could save Baytrail, it would always fail to invalidate its TLB. Ville
was right, Baytrail is beyond hope.
v2: Rollback on all gen7; same timing instability on TLB invalidation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830180000.24608-1-chris@chris-wilson.co.uk
Lucas De Marchi [Thu, 29 Aug 2019 21:15:26 +0000 (14:15 -0700)]
drm/i915: unify icp, tgp and mcc irq setup
Use a single function to setup the SDE irq and make MCC, ICP and TGP use
it, just like was done for the irq handler.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190829211526.30525-4-jose.souza@intel.com
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Lucas De Marchi [Thu, 29 Aug 2019 21:15:25 +0000 (14:15 -0700)]
drm/i915: parameterize SDE hotplug registers
Ice Lake, Tiger Lake and Elkhart Lake all have different port
configurations and all of them can be parameterized the same way to form
the SDE hotplug bitmask. Avoid making them a special case an just use
the parameterized macros.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190829211526.30525-3-jose.souza@intel.com
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Lucas De Marchi [Thu, 29 Aug 2019 21:15:24 +0000 (14:15 -0700)]
drm/i915: unify icp, tgp and mcc irq handling
The differences are only on the pins, trigger and long_detect function.
The MCC handling is already partially merged, so merge TGP as well.
Remove the pins argument from icp_irq_handler() so we have all the
differences between the 3 set in a common if ladder.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190829211526.30525-2-jose.souza@intel.com
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Lucas De Marchi [Thu, 29 Aug 2019 21:15:23 +0000 (14:15 -0700)]
drm/i915: parameterize south hpd macros
South, follow the north.
Instead of defining separate macros for each port, make them take port
as parameter as done for TC ports and for north engine. This will allow
us to easily extend this as needed.
tgp_ddi_port_hotplug_long_detect() is also removed as after the EHL
introduction the tgp variant is an exact copy of icp.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190829211526.30525-1-jose.souza@intel.com
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Joonas Lahtinen [Fri, 30 Aug 2019 08:58:49 +0000 (11:58 +0300)]
drm/i915: Indent GuC/WOPCM documentation sections
Indent GuC/WOPCM documentation correctly to reside under
"Memory Management and Command Submission" section to avoid
it escaping to the upper level navigation.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830085849.12519-2-joonas.lahtinen@linux.intel.com
Joonas Lahtinen [Fri, 30 Aug 2019 08:58:48 +0000 (11:58 +0300)]
drm/i915: Remove link to missing "Batchbuffer Pools" documentation
The referenced documentation section has been removed. Remove the
link to avoid warning when building the documentation.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830085849.12519-1-joonas.lahtinen@linux.intel.com
Ramalingam C [Wed, 28 Aug 2019 16:42:16 +0000 (22:12 +0530)]
drm/i915/hdcp: Enable HDCP 1.4 and 2.2 on Gen12+
>From Gen12 onwards, HDCP HW block is implemented within transcoders.
Till Gen11 HDCP HW block was part of DDI.
Hence required changes in HW programming is handled here.
As ME FW needs the transcoder detail on which HDCP is enabled
on Gen12+ platform, we are populating the detail in hdcp_port_data.
v2:
_MMIO_TRANS is used [Lucas and Daniel]
platform check is moved into the caller [Lucas]
v3:
platform check is moved into a macro [Shashank]
v4:
Few optimizations in the coding [Shashank]
v5:
Fixed alignment in macro definition in i915_reg.h [Shashank]
unused variables "reg" is removed.
v6:
Configuring the transcoder at compute_config.
transcoder is used instead of pipe in macros.
Rebased.
v7:
transcoder is cached at intel_hdcp
hdcp_port_data is configured with transcoder index asper ME FW.
v8:
s/trans/cpu_transcoder
s/tc/cpu_transcoder
v9:
rep_ctl is prepared for TCD too.
return moved into deault of rep_ctl prepare function [Shashank]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-7-ramalingam.c@intel.com
Ramalingam C [Wed, 28 Aug 2019 16:42:15 +0000 (22:12 +0530)]
drm/i915/hdcp: update current transcoder into intel_hdcp
On gen12+ platforms, HDCP HW is associated to the transcoder.
Hence on every modeset update associated transcoder into the
intel_hdcp of the port.
v2:
s/trans/cpu_transcoder [Jani]
v3:
comment is added for fw_ddi init for gen12+ [Shashank]
only hdcp capable transcoder is translated into fw_tc [Shashank]
v4:
fw_tc initialization is kept for modeset. [Tomas]
few extra doc is added at port_data init [Tomas]
v5:
Few comments are improvised [Tomas]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-6-ramalingam.c@intel.com
Ramalingam C [Wed, 28 Aug 2019 16:42:14 +0000 (22:12 +0530)]
misc/mei/hdcp: Fill transcoder index in port info
For gen12+ platform we need to pass the transcoder info
as part of the port info into ME FW.
This change fills the payload for ME FW from hdcp_port_data.
v2:
Doc is enhanced for physical_port and attached_transcoder [Tomas]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-5-ramalingam.c@intel.com
Ramalingam C [Wed, 28 Aug 2019 16:42:13 +0000 (22:12 +0530)]
drm: Extend I915 mei interface for transcoder info
I915 needs to send the index of the transcoder as per ME FW.
To support this, define enum mei_fw_tc and add as a member into
the struct hdcp_port_data.
v2:
Typo in commit msg is fixed [Shashank]
v3:
kdoc is added for mei_fw_tc [Tomas]
s/MEI_TC_x/MEI_TRANSCODER_x
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-4-ramalingam.c@intel.com
Ramalingam C [Wed, 28 Aug 2019 16:42:12 +0000 (22:12 +0530)]
drm: Move port definition back to i915 header
We dont need the definition of the enum port outside I915, anymore.
Hence move enum port definition into I915 driver itself.
v2:
intel_display.h is included in intel_hdcp.h
v3:
enum port is declared in headers.
v4:
commit msg is rephrased.
v5:
copyright year is updated [Tomas]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-3-ramalingam.c@intel.com
Ramalingam C [Wed, 28 Aug 2019 16:42:11 +0000 (22:12 +0530)]
drm/i915: mei_hdcp: I915 sends ddi index as per ME FW
I915 converts it's port value into ddi index defiend by ME FW
and pass it as a member of hdcp_port_data structure.
Hence expose the enum mei_fw_ddi to I915 through
i915_mei_interface.h.
v2:
Copyright years are bumped [Tomas]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828164216.405-2-ramalingam.c@intel.com
Chris Wilson [Thu, 29 Aug 2019 08:11:15 +0000 (09:11 +0100)]
drm/i915/execlists: Try rearranging breadcrumb flush
The addition of the DC_FLUSH failed to ensure sanctity of the post-sync
write as CI immediately got a completion CS-event before the breadcrumb
was coherent. So let's try the other idea of moving the post-sync write
into the CS_STALL.
References: https://bugs.freedesktop.org/show_bug.cgi?id=111514
References:
e8f6b4952ec5 ("drm/i915/execlists: Flush the post-sync breadcrumb write harder")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190829081150.10271-2-chris@chris-wilson.co.uk
Manasi Navare [Wed, 28 Aug 2019 22:47:01 +0000 (15:47 -0700)]
drm/i915/display: Move the commit_tail() disable sequence to separate function
Create a new function intel_commit_modeset_disables() consistent
with the naming in drm atomic helpers and similar to the enable function.
This helps better organize the disable sequence in atomic_commit_tail()
No functional change
v4:
* Do not create a function pointer, just a function (Maarten)
v3:
* Rebase (Manasi)
v2:
* Create a helper for old_crtc_state disables (Lucas)
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190828224701.422-1-manasi.d.navare@intel.com
Manasi Navare [Tue, 27 Aug 2019 22:17:34 +0000 (15:17 -0700)]
drm/i915/display: Rename update_crtcs() to commit_modeset_enables()
This patch has no functional changes. This just renames the update_crtcs()
hooks to commit_modeset_enables() to match the drm_atomic helper naming
conventions.
v2:
* Rebase on drm-tip
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827221735.29351-2-manasi.d.navare@intel.com
Matthew Auld [Thu, 29 Aug 2019 20:19:19 +0000 (21:19 +0100)]
drm/i915: s/for_each_sgt_dma/for_each_sgt_daddr/
The sg_table for our backing store might contain addresses from
stolen-memory or in the future local-memory, at which point this is no
longer a dma-iterator. As a consequence we should now break on NULL
iter.sgp, instead of dmap == 0 which is considered an invalid dma
address.
As a bonus, gcc much prefers this construct,
Function old new delta
gen8_ggtt_insert_entries 211 192 -19
gen6_ggtt_insert_entries 292 262 -30
i915_error_object_create 996 954 -42
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190829201919.21493-1-matthew.auld@intel.com
Fernando Pacheco [Thu, 29 Aug 2019 17:41:53 +0000 (10:41 -0700)]
drm/i915/uc: Extract common code from GuC stop/disable comm
During normal driver unload we attempt to disable GuC communication
while it is currently stopped. This results in a nop'd call to
intel_guc_ct_disable within guc_disable_communication because
stop/disable rely on the same flag to prevent further comms with CT.
We can avoid the call to disable and still leave communication in a
satisfactory state by extracting a set of shared steps from stop/disable.
This set can include guc_disable_interrupts as we do not require the
single caller of guc_stop_communication to be atomic:
"drm/i915/selftests: Fixup atomic reset checking".
This situation (stop -> disable) only occurs during intel_uc_fini_hw,
so during fini, call guc_disable_communication only if currently enabled.
The symmetric calls to enable/disable remain unmodified for all other
scenarios.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110943
Signed-off-by: Fernando Pacheco <fernando.pacheco@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190829174154.14675-1-fernando.pacheco@intel.com
Chris Wilson [Thu, 29 Aug 2019 17:08:48 +0000 (18:08 +0100)]
drm/i915/selftests: cond_resched() within the longer buddy tests
Let the scheduler have a breather in between passes of the longer buddy
tests. Important if we are running under kasan etc and this takes far
longer than usual!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190829170848.969-1-chris@chris-wilson.co.uk
José Roberto de Souza [Fri, 23 Aug 2019 08:20:39 +0000 (01:20 -0700)]
drm/i915/tgl: PSR link standby is not supported anymore
According to BSpc if link standby is set on TGL+, PSR will not be
enabled. Vendors should not use panels that requires link standby and
even if they do, panel should assert a PSR error that will cause PSR to
be disabled.
BSpec: 50434
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-8-lucas.demarchi@intel.com
Dhinakaran Pandiyan [Tue, 27 Aug 2019 08:45:16 +0000 (01:45 -0700)]
drm/i915/tgl: Gen-12 display loses Yf tiling and legacy CCS support
Yf tiling was removed in gen-12, so do not expose Yf modifiers to user
space. Gen-12 display also is incompatible with pre-gen12 Y-tiled
CCS, so do not expose I915_FORMAT_MOD_Y_TILED_CCS.
v2: Rebase to carry forward recently added gen11 formats.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827084516.6748-1-dhinakaran.pandiyan@intel.com
Madhumitha Tolakanahalli Pradeep [Fri, 23 Aug 2019 00:46:55 +0000 (17:46 -0700)]
drm/i915/tgl: Enabling DSC on Pipe A for TGL
DSC was not supported on Pipe A for previous platforms. Tigerlake onwards,
all the pipes support DSC. Hence, the DSC and FEC restriction on
Pipe A needs to be removed.
v2: Changes in the logic around removing the restriction around
Pipe A (Manasi, Lucas)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Madhumitha Tolakanahalli Pradeep <madhumitha.tolakanahalli.pradeep@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823004655.28905-1-madhumitha.tolakanahalli.pradeep@intel.com
Chris Wilson [Mon, 26 Aug 2019 07:21:27 +0000 (08:21 +0100)]
drm/i915: Protect our local workers against I915_FENCE_TIMEOUT
Trust our own workers to not cause unnecessary delays and disable the
automatic timeout on their asynchronous fence waits. (Along the same
lines that we trust our own requests to complete eventually, if
necessary by force.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826072149.9447-6-chris@chris-wilson.co.uk
Imre Deak [Fri, 23 Aug 2019 10:07:11 +0000 (13:07 +0300)]
drm/i915: Align power domain names with port names
There is a difference in BSpec's and the driver's designation of DDI
ports. BSpec uses the following names:
- before GEN11:
BSpec/driver:
port A/B/C/D etc
- GEN11:
BSpec/driver:
port A-F
- GEN12:
BSpec:
port A/B/C for combo PHY ports
port TC1-6 for Type C PHY ports
driver:
port A-I.
The driver's port D name matches BSpec's TC1 port name.
So far power domains were named according to the BSpec designation, to
make it easier to match the code against the specification. That however
can be confusing when a power domain needs to be matched to a port on
GEN12+. To resolve that use the driver's port A-I designation for power
domain names too and rename the corresponding power wells so that they
reflect the mapping from the driver's to BSpec's port name.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823100711.27833-1-imre.deak@intel.com
Chris Wilson [Mon, 26 Aug 2019 13:38:37 +0000 (14:38 +0100)]
drm/i915/selftests: Ignore coherency failures on Broadwater
We've been ignoring similar coherency issues in IGT for Broadwater, and
specifically Broadwater (original gen4) and not, for example, Crestline
(same generation as Broadwater, but the mobile variant). Without any
means to reproduce locally (I have a 965GM but alas no 965G), fixing will
be slow, so tell CI to ignore any failure until we are ready with a fix.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826133837.6784-1-chris@chris-wilson.co.uk
Mika Kuoppala [Fri, 9 Aug 2019 14:56:53 +0000 (17:56 +0300)]
drm/i915: Extend non readable mcr range
Our current avoidance of non readable mcr range was not
inclusive enough. Extend the start and end.
References: HSDES#
1405586840
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190809145653.2279-1-mika.kuoppala@linux.intel.com
Chris Wilson [Tue, 27 Aug 2019 12:06:15 +0000 (13:06 +0100)]
drm/i915/execlists: Flush the post-sync breadcrumb write harder
Quite rarely we see that the CS completion event fires before the
breadcrumb is coherent, which presumably is a result of the CS_STALL not
waiting for the post-sync operation. Try throwing in a DC_FLUSH into
the following pipecontrol to see if that makes any difference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827120615.31390-1-chris@chris-wilson.co.uk
Chris Wilson [Tue, 27 Aug 2019 16:17:26 +0000 (17:17 +0100)]
drm/i915/selftests: Try to recycle context allocations
igt_ctx_exec allocates a new context for each iteration, keeping them
all allocated until the end. Instead, release the local ctx reference at
the end of each iteration, allowing ourselves to reap those if under
mempressure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827161726.3640-2-chris@chris-wilson.co.uk
Chris Wilson [Tue, 27 Aug 2019 16:17:25 +0000 (17:17 +0100)]
drm/i915/selftests: Remove accidental serialization between gpu_fill
Upon object creation for live_gem_contexts, we fill the object with
known scratch and flush it out of the CPU cache. Before performing the
GPU fill, we don't need to flush it again and so avoid serialising with
previous fills.
However, we do need some throttling on the internal interfaces if we do
not want to run out of memory!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827161726.3640-1-chris@chris-wilson.co.uk
Daniele Ceraolo Spurio [Tue, 27 Aug 2019 18:58:05 +0000 (11:58 -0700)]
drm/i915: use a separate context for gpu relocs
The CS pre-parser can pre-fetch commands across memory sync points and
starting from gen12 it is able to pre-fetch across BB_START and BB_END
boundaries as well, so when we emit gpu relocs the pre-parser might
fetch the target location of the reloc before the memory write lands.
The parser can't pre-fetch across the ctx switch, so we use a separate
context to guarantee that the memory is synchronized before the parser
can get to it.
Note that there is no risk of the CS doing a lite restore from the reloc
context to the user context, even if the two have the same hw_id,
because since gen11 the CS also checks the LRCA when deciding if it can
lite-restore.
v2: limit new context to gen12+, release in eb_destroy, add a comment
in emit_fini_breadcrumb (Chris).
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827185805.21799-1-daniele.ceraolospurio@intel.com
Michel Thierry [Fri, 23 Aug 2019 08:20:50 +0000 (01:20 -0700)]
drm/i915/tgl/perf: use the same oa ctx_id format as icl
Compared to Icelake, Tigerlake's MAX_CONTEXT_HW_ID is smaller by one, but
since we just use the upper 32 bits of the lrc_desc, it's guaranteed OA
will use the correct one.
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-19-lucas.demarchi@intel.com
Michel Thierry [Fri, 23 Aug 2019 08:20:48 +0000 (01:20 -0700)]
drm/i915/tgl: Do not apply WaIncreaseDefaultTLBEntries from GEN12 onwards
Workaround no longer needed (plus L3_LRA_1_GPGPU doesn't exist).
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-17-lucas.demarchi@intel.com
José Roberto de Souza [Fri, 23 Aug 2019 08:20:47 +0000 (01:20 -0700)]
drm/i915/tgl: Implement TGL DisplayPort training sequence
On TGL some registers moved from DDI to transcoder and the
DisplayPort training sequence has a separate BSpec page.
I started adding 'ifs' to the original intel_ddi_pre_enable_dp() but
it was becoming really hard to follow, so a new and cleaner function
for TGL was added with comments of all steps. It's similar to ICL,
but different enough to deserve a new function.
The rest of DisplayPort enable and the whole disable sequences
remained the same.
v2: FEC and DSC should be enabled on sink side before start link
training(Maarten reported and Manasi confirmed the DSC part)
v3: Add call to enable FEC on step 7.l(Manasi)
BSpec: 49190
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-16-lucas.demarchi@intel.com
José Roberto de Souza [Fri, 23 Aug 2019 08:20:44 +0000 (01:20 -0700)]
drm/i915: Disable pipes in reverse order
Disable CRTC/pipes in reverse order because some features (MST in
TGL+) requires master and slave relationship between pipes, so it
should always pick the lowest pipe as master as it will be enabled
first and disable in the reverse order so the master will be the last
one to be disabled.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-13-lucas.demarchi@intel.com
José Roberto de Souza [Fri, 23 Aug 2019 08:20:43 +0000 (01:20 -0700)]
drm: Add for_each_oldnew_intel_crtc_in_state_reverse()
Same as for_each_oldnew_intel_crtc_in_state() but iterates in reverse
order.
v2: Fix additional blank line
v3: Rebase
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-12-lucas.demarchi@intel.com
José Roberto de Souza [Fri, 23 Aug 2019 08:20:41 +0000 (01:20 -0700)]
drm/i915/tgl: Add maximum resolution supported by PSR2 HW
TGL PSR2 HW supports a bigger resolution, so lets add it
BSpec: 50422, 49199
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-10-lucas.demarchi@intel.com
José Roberto de Souza [Sat, 17 Aug 2019 09:38:33 +0000 (02:38 -0700)]
drm/i915: Do not read PSR2 register in transcoders without PSR2
This fix unclaimed access warnings:
[ 245.525788] ------------[ cut here ]------------
[ 245.525884] Unclaimed read from register 0x62900
[ 245.526154] WARNING: CPU: 0 PID: 1234 at drivers/gpu/drm/i915/intel_uncore.c:1100 __unclaimed_reg_debug+0x40/0x50 [i915]
[ 245.526160] Modules linked in: i915 x86_pkg_temp_thermal ax88179_178a coretemp usbnet crct10dif_pclmul mii crc32_pclmul ghash_clmulni_intel e1000e [last unloaded: i915]
[ 245.526191] CPU: 0 PID: 1234 Comm: kms_fullmodeset Not tainted 5.1.0-rc6+ #915
[ 245.526197] Hardware name: Intel Corporation Tiger Lake Client Platform/TigerLake U DDR4 SODIMM RVP, BIOS TGLSFWR1.D00.2081.A10.
1904182155 04/18/2019
[ 245.526273] RIP: 0010:__unclaimed_reg_debug+0x40/0x50 [i915]
[ 245.526281] Code: 74 05 5b 5d 41 5c c3 45 84 e4 48 c7 c0 76 97 21 a0 48 c7 c6 6c 97 21 a0 89 ea 48 0f 44 f0 48 c7 c7 7f 97 21 a0 e8 4f 1e fe e0 <0f> 0b 83 2d 6f d9 1c 00 01 5b 5d 41 5c c3 66 90 41 57 41 56 41 55
[ 245.526288] RSP: 0018:
ffffc900006bf7d8 EFLAGS:
00010086
[ 245.526297] RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000000
[ 245.526304] RDX:
0000000000000007 RSI:
0000000000000000 RDI:
00000000ffffffff
[ 245.526310] RBP:
0000000000061900 R08:
0000000000000000 R09:
0000000000000001
[ 245.526317] R10:
0000000000000006 R11:
0000000000000000 R12:
0000000000000001
[ 245.526324] R13:
0000000000000000 R14:
ffff8882914f0d58 R15:
0000000000000206
[ 245.526332] FS:
00007fed2a3c39c0(0000) GS:
ffff8882a8600000(0000) knlGS:
0000000000000000
[ 245.526340] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 245.526347] CR2:
00007fed28dff000 CR3:
00000002a086c006 CR4:
0000000000760ef0
[ 245.526354] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 245.526361] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 245.526367] PKRU:
55555554
[ 245.526373] Call Trace:
[ 245.526454] gen11_fwtable_read32+0x219/0x250 [i915]
[ 245.526576] intel_psr_activate+0x57/0x400 [i915]
[ 245.526697] intel_psr_enable_locked+0x367/0x4b0 [i915]
[ 245.526828] intel_psr_enable+0xa4/0xd0 [i915]
[ 245.526946] intel_enable_ddi+0x127/0x2f0 [i915]
[ 245.527075] intel_encoders_enable.isra.79+0x62/0x90 [i915]
[ 245.527202] haswell_crtc_enable+0x2a2/0x850 [i915]
[ 245.527337] intel_update_crtc+0x51/0x360 [i915]
[ 245.527466] skl_update_crtcs+0x26c/0x300 [i915]
[ 245.527603] intel_atomic_commit_tail+0x3e5/0x13c0 [i915]
[ 245.527757] intel_atomic_commit+0x24d/0x2d0 [i915]
[ 245.527782] drm_atomic_helper_set_config+0x7b/0x90
[ 245.527799] drm_mode_setcrtc+0x1b4/0x6f0
[ 245.527856] ? drm_mode_getcrtc+0x180/0x180
[ 245.527867] drm_ioctl_kernel+0xad/0xf0
[ 245.527886] drm_ioctl+0x2f4/0x3b0
[ 245.527902] ? drm_mode_getcrtc+0x180/0x180
[ 245.527935] ? rcu_read_lock_sched_held+0x6f/0x80
[ 245.527956] do_vfs_ioctl+0xa0/0x6d0
[ 245.527970] ? __task_pid_nr_ns+0xb6/0x200
[ 245.527991] ksys_ioctl+0x35/0x70
[ 245.528009] __x64_sys_ioctl+0x11/0x20
[ 245.528020] do_syscall_64+0x55/0x180
[ 245.528034] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 245.528042] RIP: 0033:0x7fed2cc7c3c7
[ 245.528050] Code: 00 00 90 48 8b 05 c9 3a 0d 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 99 3a 0d 00 f7 d8 64 89 01 48
[ 245.528057] RSP: 002b:
00007ffe36944378 EFLAGS:
00000246 ORIG_RAX:
0000000000000010
[ 245.528067] RAX:
ffffffffffffffda RBX:
00007ffe369443b0 RCX:
00007fed2cc7c3c7
[ 245.528074] RDX:
00007ffe369443b0 RSI:
00000000c06864a2 RDI:
0000000000000003
[ 245.528081] RBP:
00007ffe369443b0 R08:
0000000000000000 R09:
0000564c0173ae98
[ 245.528088] R10:
0000564c0173aeb8 R11:
0000000000000246 R12:
00000000c06864a2
[ 245.528095] R13:
0000000000000003 R14:
0000000000000000 R15:
0000000000000000
[ 245.528128] irq event stamp: 140866
[ 245.528138] hardirqs last enabled at (140865): [<
ffffffff819a63dc>] _raw_spin_unlock_irqrestore+0x4c/0x60
[ 245.528148] hardirqs last disabled at (140866): [<
ffffffff819a624d>] _raw_spin_lock_irqsave+0xd/0x50
[ 245.528158] softirqs last enabled at (140860): [<
ffffffff81c0038c>] __do_softirq+0x38c/0x499
[ 245.528170] softirqs last disabled at (140853): [<
ffffffff810b4a09>] irq_exit+0xa9/0xc0
[ 245.528247] WARNING: CPU: 0 PID: 1234 at drivers/gpu/drm/i915/intel_uncore.c:1100 __unclaimed_reg_debug+0x40/0x50 [i915]
[ 245.528254] ---[ end trace
366069676e98a410 ]---
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-7-lucas.demarchi@intel.com
José Roberto de Souza [Fri, 23 Aug 2019 08:20:37 +0000 (01:20 -0700)]
drm/i915/tgl: Guard and warn if more than one eDP panel is present
On TGL+ it's possible to have PSR1 enabled in other ports besides DDIA.
PSR2 is still limited to DDIA. However currently we handle only one
instance of PSR struct. Lets guard intel_psr_init_dpcd() against
multiple eDP panels and warn about it.
v2: Reword commit message to be TGL+ only and with the info where
PSR1/PSR2 are supported (Lucas)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-6-lucas.demarchi@intel.com
Chris Wilson [Tue, 27 Aug 2019 13:59:35 +0000 (14:59 +0100)]
drm/i915: Make engine's batch pool safe for use with virtual engines
A virtual engine itself does not have a batch pool, but we can gleefully
use any of its siblings instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827135935.3831-1-chris@chris-wilson.co.uk
Chris Wilson [Tue, 27 Aug 2019 13:26:31 +0000 (14:26 +0100)]
drm/i915: Only activate i915_active debugobject once
The point of debug_object_activate is to mark the first, and only the
first, acquisition. The object then remains active until the last
release. However, we marked up all successful first acquires even though
we allowed concurrent parties to try and acquire the i915_active
simultaneously (serialised by the i915_active.mutex).
Testcase: igt/gem_mmap_gtt/fault-concurrent
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827132631.18627-1-chris@chris-wilson.co.uk
Chris Wilson [Tue, 27 Aug 2019 09:49:33 +0000 (10:49 +0100)]
drm/i915/selftests: Markup impossible error pointers
If we create a new live_context() we should have a mapping for each
engine. Document that assumption with an assertion.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190827094933.13778-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 26 Aug 2019 13:07:50 +0000 (14:07 +0100)]
drm/i915: Use NOEVICT for first pass on attemping to pin a GGTT mmap
The intention is that we first try to pin the current vma into the
mappable aperture only if it is already in use or it fits in the free
space and will not cause contention. The first attempt was meant to be
using PIN_NOEVICT to reuse the current vma if possible, following up
with different eviction strategies.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111485
Fixes:
6846895fde05 ("drm/i915: Replace PIN_NONFAULT with calls to PIN_NOEVICT")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826130750.17272-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 26 Aug 2019 07:21:22 +0000 (08:21 +0100)]
drm/i915/selftests: Add the usual batch vma managements to st_workarounds
To properly handle asynchronous migration of batch objects, we need to
couple the fences on the incoming batch into the request and should not
assume that they always start idle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826072149.9447-1-chris@chris-wilson.co.uk
Lyude Paul [Fri, 23 Aug 2019 20:52:51 +0000 (16:52 -0400)]
drm/i915: Call dma_set_max_seg_size() in i915_driver_hw_probe()
Currently, we don't call dma_set_max_seg_size() for i915 because we
intentionally do not limit the segment length that the device supports.
However, this results in a warning being emitted if we try to map
anything larger than SZ_64K on a kernel with CONFIG_DMA_API_DEBUG_SG
enabled:
[ 7.751926] DMA-API: i915 0000:00:02.0: mapping sg segment longer
than device claims to support [len=98304] [max=65536]
[ 7.751934] WARNING: CPU: 5 PID: 474 at kernel/dma/debug.c:1220
debug_dma_map_sg+0x20f/0x340
This was originally brought up on
https://bugs.freedesktop.org/show_bug.cgi?id=108517 , and the consensus
there was it wasn't really useful to set a limit (and that dma-debug
isn't really all that useful for i915 in the first place). Unfortunately
though, CONFIG_DMA_API_DEBUG_SG is enabled in the debug configs for
various distro kernels. Since a WARN_ON() will disable automatic problem
reporting (and cause any CI with said option enabled to start
complaining), we really should just fix the problem.
Note that as me and Chris Wilson discussed, the other solution for this
would be to make DMA-API not make such assumptions when a driver hasn't
explicitly set a maximum segment size. But, taking a look at the commit
which originally introduced this behavior, commit
78c47830a5cb
("dma-debug: check scatterlist segments"), there is an explicit mention
of this assumption and how it applies to devices with no segment size:
Conversely, devices which are less limited than the rather
conservative defaults, or indeed have no limitations at all
(e.g. GPUs with their own internal MMU), should be encouraged to
set appropriate dma_parms, as they may get more efficient DMA
mapping performance out of it.
So unless there's any concerns (I'm open to discussion!), let's just
follow suite and call dma_set_max_seg_size() with UINT_MAX as our limit
to silence any warnings.
Changes since v3:
* Drop patch for enabling CONFIG_DMA_API_DEBUG_SG in CI. It looks like
just turning it on causes the kernel to spit out bogus WARN_ONs()
during some igt tests which would otherwise require teaching igt to
disable the various DMA-API debugging options causing this. This is
too much work to be worth it, since DMA-API debugging is useless for
us. So, we'll just settle with this single patch to squelch WARN_ONs()
during driver load for users that have CONFIG_DMA_API_DEBUG_SG turned
on for some reason.
* Move dma_set_max_seg_size() call into i915_driver_hw_probe() - Chris
Wilson
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.18+
Link: https://patchwork.freedesktop.org/patch/msgid/20190823205251.14298-1-lyude@redhat.com
Xiaolin Zhang [Fri, 23 Aug 2019 06:57:31 +0000 (14:57 +0800)]
drm/i915: to make vgpu ppgtt notificaiton as atomic operation
vgpu ppgtt notification was split into 2 steps, the first step is to
update PVINFO's pdp register and then write PVINFO's g2v_notify register
with action code to tirgger ppgtt notification to GVT side.
currently these steps were not atomic operations due to no any protection,
so it is easy to enter race condition state during the MTBF, stress and
IGT test to cause GPU hang.
the solution is to add a lock to make vgpu ppgtt notication as atomic
operation.
Cc: stable@vger.kernel.org
Signed-off-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1566543451-13955-1-git-send-email-xiaolin.zhang@intel.com
Chris Wilson [Fri, 23 Aug 2019 23:51:41 +0000 (00:51 +0100)]
drm/i915/selftests: Teach igt_gpu_fill_dw() to take intel_context
Avoid having to pass around (ctx, engine) everywhere by passing the
actual intel_context we intend to use. Today we preach this lesson to
igt_gpu_fill_dw and its callers' callers.
The immediate benefit for the GEM selftests is that we aim to use the
GEM context as the control, the source of the engines on which to test
the GEM context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823235141.31799-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 23 Aug 2019 18:14:55 +0000 (19:14 +0100)]
drm/i915: Keep drm_i915_file_private around under RCU
Ensure that the drm_i915_file_private continues to exist as we attempt
to remove a request from its list, which may race with the destruction
of the file.
<6> [38.380714] [IGT] gem_ctx_create: starting subtest basic-files
<0> [42.201329] BUG: spinlock bad magic on CPU#0, kworker/u16:0/7
<4> [42.201356] general protection fault: 0000 [#1] PREEMPT SMP PTI
<4> [42.201371] CPU: 0 PID: 7 Comm: kworker/u16:0 Tainted: G U 5.3.0-rc5-CI-Patchwork_14169+ #1
<4> [42.201391] Hardware name: Dell Inc. OptiPlex 745 /0GW726, BIOS 2.3.1 05/21/2007
<4> [42.201594] Workqueue: i915 retire_work_handler [i915]
<4> [42.201614] RIP: 0010:spin_dump+0x5a/0x90
<4> [42.201625] Code: 00 48 8d 88 c0 06 00 00 48 c7 c7 00 71 09 82 e8 35 ef 00 00 48 85 db 44 8b 4d 08 41 b8 ff ff ff ff 48 c7 c1 0b cd 0f 82 74 0e <44> 8b 83 e0 04 00 00 48 8d 8b c0 06 00 00 8b 55 04 48 89 ee 48 c7
<4> [42.201660] RSP: 0018:
ffffc9000004bd80 EFLAGS:
00010202
<4> [42.201673] RAX:
0000000000000031 RBX:
6b6b6b6b6b6b6b6b RCX:
ffffffff820fcd0b
<4> [42.201688] RDX:
0000000000000000 RSI:
ffff88803de266f8 RDI:
00000000ffffffff
<4> [42.201703] RBP:
ffff888038381ff8 R08:
00000000ffffffff R09:
000000006b6b6b6b
<4> [42.201718] R10:
0000000041cb0b89 R11:
646162206b636f6c R12:
ffff88802a618500
<4> [42.201733] R13:
ffff88802b32c288 R14:
ffff888038381ff8 R15:
ffff88802b32c250
<4> [42.201748] FS:
0000000000000000(0000) GS:
ffff88803de00000(0000) knlGS:
0000000000000000
<4> [42.201765] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
<4> [42.201778] CR2:
00007f2cefc6d180 CR3:
00000000381ee000 CR4:
00000000000006f0
<4> [42.201793] Call Trace:
<4> [42.201805] do_raw_spin_lock+0x66/0xb0
<4> [42.201898] i915_request_retire+0x548/0x7c0 [i915]
<4> [42.201989] retire_requests+0x4d/0x60 [i915]
<4> [42.202078] i915_retire_requests+0x144/0x2e0 [i915]
<4> [42.202169] retire_work_handler+0x10/0x40 [i915]
Recently, in commit
44c22f3f1a0a ("drm/i915: Serialize insertion into the
file->mm.request_list"), we fixed a race on insertion. Now, it appears
we also have a race with destruction!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823181455.31910-1-chris@chris-wilson.co.uk
Daniele Ceraolo Spurio [Tue, 20 Aug 2019 01:23:27 +0000 (18:23 -0700)]
drm/i915/uc: define GuC and HuC FWs for EHL
First uc firmware release for EHL.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820012327.36443-1-daniele.ceraolospurio@intel.com
Chris Wilson [Fri, 23 Aug 2019 15:39:44 +0000 (16:39 +0100)]
drm/i915: Flush the existing fence before GGTT read/write
Our fence management is lazy, very lazy. If the user marks an object as
untiled, we do not immediately flush the fence but merely mark it as
dirty. On the next use we have to remember to check and remove the fence,
by which time we hope it is idle and we do not have to wait.
v2: Throw away the old fence on the next ggtt_pin.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111468
Fixes:
1f7fd484fff1 ("drm/i915: Replace i915_vma_put_fence()")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823153944.20630-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 23 Aug 2019 14:14:21 +0000 (15:14 +0100)]
drm/i915/gtt: Preallocate Braswell top-level page directory
In order for the Braswell top-level PD to remain the same from the time
of request construction to its submission onto HW, as we may be
asynchronously rewriting the page tables (thus changing the expected
register state after having already stored the old addresses in the
request), the top level PD must be preallocated.
So wave goodbye to our lazy allocation of those 4x2 pages.
v2: A little bit of write-flushing required (presumably it always has
been required, but now we are more susceptible and it is showing up!)
v3: Put back the forced-PD-reload on every batch, we can't survive
without it and explicitly marking the context for PD reload makes
Braswell turn nasty.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823141421.2398-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 23 Aug 2019 13:26:46 +0000 (14:26 +0100)]
drm/i915: Hold irq-off for the entire fake lock period
Sadly lockdep records when the irqs are re-enabled and then marks up the
fake lock as being irq-unsafe. Our hand is forced and so we must mark up
the entire fake lock critical section as irq-off.
Hopefully this is the last tweak required!
v2: Not quite, we need to mark the timeline spinlock as irqsafe. That
was a genuine bug being hidden by the earlier lockdep splat.
Fixes:
d67739268cf0 ("drm/i915/gt: Mark up the nested engine-pm timeline lock as irqsafe")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823132700.25286-2-chris@chris-wilson.co.uk
Ville Syrjälä [Wed, 21 Aug 2019 17:30:33 +0000 (20:30 +0300)]
drm/i915: Use hweight8() for 8bit masks
Use hweight8() instead of hweight32() for 8bit masks. Doesn't actually
matter for us since the arch code will go for hweight32() anyway, but
maybe we stil want to do this for documentation purposes?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821173033.24123-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Wed, 21 Aug 2019 17:30:32 +0000 (20:30 +0300)]
drm/i915: s/num_active_crtcs/num_active_pipes/
Set a good example and talk about pipes rather than crtcs.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821173033.24123-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Wed, 21 Aug 2019 17:30:31 +0000 (20:30 +0300)]
drm/i915: Use enum pipe consistently
Replace all "int pipe"s with "enum pipe pipe"s to make it clear
what we're dealing with.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821173033.24123-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Wed, 21 Aug 2019 17:30:30 +0000 (20:30 +0300)]
drm/i915: Unconfuse pipe vs. crtc->index in i915_get_crtc_scanoutpos()
The "pipe" argument passed in by the vblank code is in fact the crtc
index. Don't assume that is the same as the pipe.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821173033.24123-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Wed, 21 Aug 2019 17:30:29 +0000 (20:30 +0300)]
drm/i915: Use enum pipe instead of crtc index to track active pipes
We may need to eliminate the crtc->index == pipe assumptions from
the code to support arbitrary pipes being fused off. Start that by
switching some bitmasks over to using pipe instead of the crtc index.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821173033.24123-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Stuart Summers [Fri, 23 Aug 2019 16:03:07 +0000 (09:03 -0700)]
drm/i915: Expand subslice mask
Currently, the subslice_mask runtime parameter is stored as an
array of subslices per slice. Expand the subslice mask array to
better match what is presented to userspace through the
I915_QUERY_TOPOLOGY_INFO ioctl. The index into this array is
then calculated:
slice * subslice stride + subslice index / 8
v2: Fix 32-bit build
v3: Use new helper function in SSEU workaround warning message
v4: Use GEM_BUG_ON to force developers to use valid SSEU configurations
per platform (Chris)
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-12-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:03:06 +0000 (09:03 -0700)]
drm/i915: Add new function to copy subslices for a slice
Add a new function to copy subslices for a specified slice
between intel_sseu structures for the purpose of determining
power-gate status. Note that currently ss_stride has a max
of 1.
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-11-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:03:05 +0000 (09:03 -0700)]
drm/i915: Refactor instdone loops on new subslice functions
Refactor instdone loops to use the new intel_sseu_has_subslice
function.
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-10-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:03:04 +0000 (09:03 -0700)]
drm/i915: Add function to determine if a slice has a subslice
Add a new function to determine whether a particular slice
has a given subslice.
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-9-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:03:03 +0000 (09:03 -0700)]
drm/i915: Use subslice stride to set subslices for a given slice
Add a subslice stride calculation when setting subslices. This
aligns more closely with the userspace expectation of the subslice
mask structure.
v2: Use local variable for subslice_mask on HSW and
clean up a few other subslice_mask local variable
changes
v3: Add GEM_BUG_ON for ss_stride to prevent array overflow (Chris)
Split main set function and refactors in intel_device_info.c
into separate patches (Chris)
v4: Reduce ss_stride size check when setting subslices per slice
based on actual expected max stride (Chris)
Move that GEM_BUG_ON check for the ss_stride out to the patch
which adds the ss_stride
v5: Use memcpy instead of looping through each stride index
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-8-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:03:02 +0000 (09:03 -0700)]
drm/i915: Add function to set subslices
Add a new function to set a set of subslices for a given
slice.
v2: Fix typo in subslice_mask assignment
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-7-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:03:01 +0000 (09:03 -0700)]
drm/i915: Use local variables for subslice_mask for device info
When setting up subslice_mask, instead of operating on the slice
array directly, use a local variable to start bits per slice, then
use this to set the per slice array in one step.
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-6-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:03:00 +0000 (09:03 -0700)]
drm/i915: Add EU stride runtime parameter
Add a new SSEU runtime parameter, eu_stride, which is
used to mirror the userspace concept of a range of EUs
per subslice.
This patch simply adds the parameter and updates usage
in the QUERY_TOPOLOGY_INFO handler.
v2: Add GEM_BUG_ON to make sure eu_stride is valid
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-5-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:02:59 +0000 (09:02 -0700)]
drm/i915: Add subslice stride runtime parameter
Add a new parameter, ss_stride, to the runtime info
structure. This is used to mirror the userspace concept
of subslice stride, which is a range of subslices per slice.
This patch simply adds the definition and updates usage
in the QUERY_TOPOLOGY_INFO handler.
v2: Add GEM_BUG_ON to make sure ss_stride is valid
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-4-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:02:58 +0000 (09:02 -0700)]
drm/i915: Add function to set SSEU info per platform
Add a new function to allow each platform to set maximum
slice, subslice, and EU information to reduce code duplication.
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-3-stuart.summers@intel.com
Stuart Summers [Fri, 23 Aug 2019 16:02:57 +0000 (09:02 -0700)]
drm/i915: Use variable for debugfs device status
Use a local variable to find SSEU runtime information
in various debugfs functions.
v2: Remove extra line breaks per feedback from Chris
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823160307.180813-2-stuart.summers@intel.com
Michel Thierry [Fri, 23 Aug 2019 08:20:34 +0000 (01:20 -0700)]
drm/i915/tgl: Enable VD HCP/MFX sub-pipe power gating
HCP/MFX power gating is disabled by default, turn it on for the vd units
available. User space will also issue a MI_FORCE_WAKEUP properly to
wake up proper subwell.
During driver load, init_clock_gating happens after device_info_init_mmio
read the vdbox disable fuse register, so only present vd units will have
these enabled.
BSpec: 14214
HSDES:
1209977827
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Tony Ye <tony.ye@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-3-lucas.demarchi@intel.com
Michel Thierry [Fri, 23 Aug 2019 08:20:33 +0000 (01:20 -0700)]
drm/i915/tgl: Move GTCR register to cope with GAM MMIO address remap
GAM registers located in the 0x4xxx range have been relocated to 0xCxxx;
this is to make space for global MOCS registers.
v2: Rename register and bitfield to its new name (suggested by Mika)
HSD: 399379
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-2-lucas.demarchi@intel.com
Manasi Navare [Wed, 21 Aug 2019 21:59:50 +0000 (14:59 -0700)]
drm/i915/dp: Fix DSC enable code to use cpu_transcoder instead of encoder->type
This patch fixes the intel_configure_pps_for_dsc_encoder() function to use
cpu_transcoder instead of encoder->type to select the correct DSC registers
that was wrongly used in the original patch for one DSC register isntance.
Fixes:
7182414e2530 ("drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190821215950.24223-1-manasi.d.navare@intel.com
Anusha Srivatsa [Tue, 20 Aug 2019 22:30:59 +0000 (15:30 -0700)]
drm/dp/dsc: Add Support for all BPCs supported by TGL
DSC engine on ICL supports only 8 and 10 BPC as the input
BPC. But DSC engine in TGL supports 8, 10 and 12 BPC.
Add 12 BPC support for DSC while calculating compression
configuration.
v2: Remove the separate define TGL_DP_DSC_MAX_SUPPORTED_BPC
and use the value directly.(More such defines can be removed
as part of future patches). (Ville)
v3: Use values directly instead of accessing the defines
everytime for min and max DSC BPC.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820223059.18052-1-anusha.srivatsa@intel.com
José Roberto de Souza [Tue, 20 Aug 2019 22:33:25 +0000 (15:33 -0700)]
drm/i915: Do not unmask PSR interruption in IRQ postinstall
No need to unmask PSR interrutpion if PSR is not enabled, better move
the call to intel_psr_enable_source().
v2: Renamed intel_psr_irq_control() to psr_irq_control() (Lucas)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820223325.27490-3-jose.souza@intel.com
José Roberto de Souza [Tue, 20 Aug 2019 22:33:24 +0000 (15:33 -0700)]
drm/i915: Add transcoder restriction to PSR2
According to PSR2_CTL definition in BSpec there is only one instance
of PSR2_CTL. Platforms gen < 12 with EDP transcoder only support PSR2
on TRANSCODER_EDP while on TGL PSR2 is only supported by
TRANSCODER_A.
Since BDW PSR is allowed on any port, but we need to restrict by
transcoder.
v8: Renamed _psr2_supported_in_trans() to psr2_supported() (Lucas)
v9: Renamed psr2_supported() to transcoder_has_psr2() (Ville)
BSpec: 7713
BSpec: 20584
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190820223325.27490-2-jose.souza@intel.com