OSDN Git Service
Daniel Schultz [Tue, 17 Sep 2019 08:12:53 +0000 (10:12 +0200)]
mfd: rk808: Fix RK818 ID template
[ Upstream commit
37ef8c2c15bdc1322b160e38986c187de2b877b2 ]
The Rockchip PMIC driver can automatically detect connected component
versions by reading the ID_MSB and ID_LSB registers. The probe function
will always fail with RK818 PMICs because the ID_MSK is 0xFFF0 and the
RK818 template ID is 0x8181.
This patch changes this value to 0x8180.
Fixes:
9d6105e19f61 ("mfd: rk808: Fix up the chip id get failed")
Cc: stable@vger.kernel.org
Cc: Elaine Zhang <zhangqing@rock-chips.com>
Cc: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
yangerkun [Thu, 19 Sep 2019 06:35:08 +0000 (14:35 +0800)]
ext4: fix a bug in ext4_wait_for_tail_page_commit
commit
565333a1554d704789e74205989305c811fd9c7a upstream.
No need to wait for any commit once the page is fully truncated.
Besides, it may confuse e.g. concurrent ext4_writepage() with the page
still be dirty (will be cleared by truncate_pagecache() in
ext4_setattr()) but buffers has been freed; and then trigger a bug
show as below:
[ 26.057508] ------------[ cut here ]------------
[ 26.058531] kernel BUG at fs/ext4/inode.c:2134!
...
[ 26.088130] Call trace:
[ 26.088695] ext4_writepage+0x914/0xb28
[ 26.089541] writeout.isra.4+0x1b4/0x2b8
[ 26.090409] move_to_new_page+0x3b0/0x568
[ 26.091338] __unmap_and_move+0x648/0x988
[ 26.092241] unmap_and_move+0x48c/0xbb8
[ 26.093096] migrate_pages+0x220/0xb28
[ 26.093945] kernel_mbind+0x828/0xa18
[ 26.094791] __arm64_sys_mbind+0xc8/0x138
[ 26.095716] el0_svc_common+0x190/0x490
[ 26.096571] el0_svc_handler+0x60/0xd0
[ 26.097423] el0_svc+0x8/0xc
Run the procedure (generate by syzkaller) parallel with ext3.
void main()
{
int fd, fd1, ret;
void *addr;
size_t length = 4096;
int flags;
off_t offset = 0;
char *str = "12345";
fd = open("a", O_RDWR | O_CREAT);
assert(fd >= 0);
/* Truncate to 4k */
ret = ftruncate(fd, length);
assert(ret == 0);
/* Journal data mode */
flags = 0xc00f;
ret = ioctl(fd, _IOW('f', 2, long), &flags);
assert(ret == 0);
/* Truncate to 0 */
fd1 = open("a", O_TRUNC | O_NOATIME);
assert(fd1 >= 0);
addr = mmap(NULL, length, PROT_WRITE | PROT_READ,
MAP_SHARED, fd, offset);
assert(addr != (void *)-1);
memcpy(addr, str, 5);
mbind(addr, length, 0, 0, 0, MPOL_MF_MOVE);
}
And the bug will be triggered once we seen the below order.
reproduce1 reproduce2
... | ...
truncate to 4k |
change to journal data mode |
| memcpy(set page dirty)
truncate to 0: |
ext4_setattr: |
... |
ext4_wait_for_tail_page_commit |
| mbind(trigger bug)
truncate_pagecache(clean dirty)| ...
... |
mbind will call ext4_writepage() since the page still be dirty, and then
report the bug since the buffers has been free. Fix it by return
directly once offset equals to 0 which means the page has been fully
truncated.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: yangerkun <yangerkun@huawei.com>
Link: https://lore.kernel.org/r/20190919063508.1045-1-yangerkun@huawei.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Darrick J. Wong [Tue, 15 Oct 2019 15:44:32 +0000 (08:44 -0700)]
splice: only read in as much information as there is pipe buffer space
commit
3253d9d093376d62b4a56e609f15d2ec5085ac73 upstream.
Andreas Grünbacher reports that on the two filesystems that support
iomap directio, it's possible for splice() to return -EAGAIN (instead of
a short splice) if the pipe being written to has less space available in
its pipe buffers than the length supplied by the calling process.
Months ago we fixed splice_direct_to_actor to clamp the length of the
read request to the size of the splice pipe. Do the same to do_splice.
Fixes:
17614445576b6 ("splice: don't read more than available pipe space")
Reported-by: syzbot+3c01db6025f26530cf8d@syzkaller.appspotmail.com
Reported-by: Andreas Grünbacher <andreas.gruenbacher@gmail.com>
Reviewed-by: Andreas Grünbacher <andreas.gruenbacher@gmail.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexandre Belloni [Sun, 20 Oct 2019 23:13:20 +0000 (01:13 +0200)]
rtc: disable uie before setting time and enable after
commit
7e7c005b4b1f1f169bcc4b2c3a40085ecc663df2 upstream.
When setting the time in the future with the uie timer enabled,
rtc_timer_do_work will loop for a while because the expiration of the uie
timer was way before the current RTC time and a new timer will be enqueued
until the current rtc time is reached.
If the uie timer is enabled, disable it before setting the time and enable
it after expiring current timers (which may actually be an alarm).
This is the safest thing to do to ensure the uie timer is still
synchronized with the RTC, especially in the UIE emulation case.
Reported-by: syzbot+08116743f8ad6f9a6de7@syzkaller.appspotmail.com
Fixes:
6610e0893b8b ("RTC: Rework RTC code to use timerqueue for events")
Link: https://lore.kernel.org/r/20191020231320.8191-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen Jun [Sun, 1 Dec 2019 01:58:11 +0000 (17:58 -0800)]
mm/shmem.c: cast the type of unmap_start to u64
commit
aa71ecd8d86500da6081a72da6b0b524007e0627 upstream.
In 64bit system. sb->s_maxbytes of shmem filesystem is MAX_LFS_FILESIZE,
which equal LLONG_MAX.
If offset > LLONG_MAX - PAGE_SIZE, offset + len < LLONG_MAX in
shmem_fallocate, which will pass the checking in vfs_fallocate.
/* Check for wrap through zero too */
if (((offset + len) > inode->i_sb->s_maxbytes) || ((offset + len) < 0))
return -EFBIG;
loff_t unmap_start = round_up(offset, PAGE_SIZE) in shmem_fallocate
causes a overflow.
Syzkaller reports a overflow problem in mm/shmem:
UBSAN: Undefined behaviour in mm/shmem.c:2014:10
signed integer overflow: '
9223372036854775807 + 1' cannot be represented in type 'long long int'
CPU: 0 PID:17076 Comm: syz-executor0 Not tainted 4.1.46+ #1
Hardware name: linux, dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x2c8 arch/arm64/kernel/traps.c:100
show_stack+0x20/0x30 arch/arm64/kernel/traps.c:238
__dump_stack lib/dump_stack.c:15 [inline]
ubsan_epilogue+0x18/0x70 lib/ubsan.c:164
handle_overflow+0x158/0x1b0 lib/ubsan.c:195
shmem_fallocate+0x6d0/0x820 mm/shmem.c:2104
vfs_fallocate+0x238/0x428 fs/open.c:312
SYSC_fallocate fs/open.c:335 [inline]
SyS_fallocate+0x54/0xc8 fs/open.c:239
The highest bit of unmap_start will be appended with sign bit 1
(overflow) when calculate shmem_falloc.start:
shmem_falloc.start = unmap_start >> PAGE_SHIFT.
Fix it by casting the type of unmap_start to u64, when right shifted.
This bug is found in LTS Linux 4.1. It also seems to exist in mainline.
Link: http://lkml.kernel.org/r/1573867464-5107-1-git-send-email-chenjun102@huawei.com
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Mon, 4 Nov 2019 15:58:15 +0000 (15:58 +0000)]
firmware: qcom: scm: Ensure 'a0' status code is treated as signed
commit
ff34f3cce278a0982a7b66b1afaed6295141b1fc upstream.
The 'a0' member of 'struct arm_smccc_res' is declared as 'unsigned long',
however the Qualcomm SCM firmware interface driver expects to receive
negative error codes via this field, so ensure that it's cast to 'long'
before comparing to see if it is less than 0.
Cc: <stable@vger.kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Theodore Ts'o [Tue, 12 Nov 2019 03:18:13 +0000 (22:18 -0500)]
ext4: work around deleting a file with i_nlink == 0 safely
commit
c7df4a1ecb8579838ec8c56b2bb6a6716e974f37 upstream.
If the file system is corrupted such that a file's i_links_count is
too small, then it's possible that when unlinking that file, i_nlink
will already be zero. Previously we were working around this kind of
corruption by forcing i_nlink to one; but we were doing this before
trying to delete the directory entry --- and if the file system is
corrupted enough that ext4_delete_entry() fails, then we exit with
i_nlink elevated, and this causes the orphan inode list handling to be
FUBAR'ed, such that when we unmount the file system, the orphan inode
list can get corrupted.
A better way to fix this is to simply skip trying to call drop_nlink()
if i_nlink is already zero, thus moving the check to the place where
it makes the most sense.
https://bugzilla.kernel.org/show_bug.cgi?id=205433
Link: https://lore.kernel.org/r/20191112032903.8828-1-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vincenzo Frascino [Mon, 2 Dec 2019 07:57:29 +0000 (07:57 +0000)]
powerpc: Fix vDSO clock_getres()
[ Upstream commit
552263456215ada7ee8700ce022d12b0cffe4802 ]
clock_getres in the vDSO library has to preserve the same behaviour
of posix_get_hrtimer_res().
In particular, posix_get_hrtimer_res() does:
sec = 0;
ns = hrtimer_resolution;
and hrtimer_resolution depends on the enablement of the high
resolution timers that can happen either at compile or at run time.
Fix the powerpc vdso implementation of clock_getres keeping a copy of
hrtimer_resolution in vdso data and using that directly.
Fixes:
a7f290dad32e ("[PATCH] powerpc: Merge vdso's and add vdso support to 32 bits kernel")
Cc: stable@vger.kernel.org
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
[chleroy: changed CLOCK_REALTIME_RES to CLOCK_HRTIMER_RES]
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a55eca3a5e85233838c2349783bcb5164dae1d09.1575273217.git.christophe.leroy@c-s.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Chancellor [Tue, 19 Nov 2019 04:57:11 +0000 (21:57 -0700)]
powerpc: Avoid clang warnings around setjmp and longjmp
[ Upstream commit
c9029ef9c95765e7b63c4d9aa780674447db1ec0 ]
Commit
aea447141c7e ("powerpc: Disable -Wbuiltin-requires-header when
setjmp is used") disabled -Wbuiltin-requires-header because of a
warning about the setjmp and longjmp declarations.
r367387 in clang added another diagnostic around this, complaining
that there is no jmp_buf declaration.
In file included from ../arch/powerpc/xmon/xmon.c:47:
../arch/powerpc/include/asm/setjmp.h:10:13: error: declaration of
built-in function 'setjmp' requires the declaration of the 'jmp_buf'
type, commonly provided in the header <setjmp.h>.
[-Werror,-Wincomplete-setjmp-declaration]
extern long setjmp(long *);
^
../arch/powerpc/include/asm/setjmp.h:11:13: error: declaration of
built-in function 'longjmp' requires the declaration of the 'jmp_buf'
type, commonly provided in the header <setjmp.h>.
[-Werror,-Wincomplete-setjmp-declaration]
extern void longjmp(long *, long);
^
2 errors generated.
We are not using the standard library's longjmp/setjmp implementations
for obvious reasons; make this clear to clang by using -ffreestanding
on these files.
Cc: stable@vger.kernel.org # 4.14+
Suggested-by: Segher Boessenkool <segher@kernel.crashing.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191119045712.39633-3-natechancellor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Anders Roxell [Wed, 12 Jun 2019 08:11:58 +0000 (10:11 +0200)]
regulator: 88pm800: fix warning same module names
[ Upstream commit
6f10419187d0d5fe395e2a2f2a64370961bf02a3 ]
When building with CONFIG_MFD_88PM800 and CONFIG_REGULATOR_88PM800
enabled as loadable modules, we see the following warning:
warning: same module names found:
drivers/regulator/88pm800.ko
drivers/mfd/88pm800.ko
Rework so that the file is named 88pm800-regulator.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqing Pan [Fri, 24 May 2019 03:16:22 +0000 (11:16 +0800)]
ath10k: fix fw crash by moving chip reset after napi disabled
[ Upstream commit
08d80e4cd27ba19f9bee9e5f788f9a9fc440a22f ]
On SMP platform, when continuously running wifi up/down, the napi
poll can be scheduled during chip reset, which will call
ath10k_pci_has_fw_crashed() to check the fw status. But in the reset
period, the value from FW_INDICATOR_ADDRESS register will return
0xdeadbeef, which also be treated as fw crash. Fix the issue by
moving chip reset after napi disabled.
ath10k_pci 0000:01:00.0: firmware crashed! (guid
73b30611-5b1e-4bdd-90b4-
64c81eb947b6)
ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
ath10k_pci 0000:01:00.0: failed to get memcpy hi address for firmware address 4: -16
ath10k_pci 0000:01:00.0: failed to read firmware dump area: -16
ath10k_pci 0000:01:00.0: Copy Engine register dump:
ath10k_pci 0000:01:00.0: [00]: 0x0004a000 0 0 0 0
ath10k_pci 0000:01:00.0: [01]: 0x0004a400 0 0 0 0
ath10k_pci 0000:01:00.0: [02]: 0x0004a800 0 0 0 0
ath10k_pci 0000:01:00.0: [03]: 0x0004ac00 0 0 0 0
ath10k_pci 0000:01:00.0: [04]: 0x0004b000 0 0 0 0
ath10k_pci 0000:01:00.0: [05]: 0x0004b400 0 0 0 0
ath10k_pci 0000:01:00.0: [06]: 0x0004b800 0 0 0 0
ath10k_pci 0000:01:00.0: [07]: 0x0004bc00 1 0 1 0
ath10k_pci 0000:01:00.0: [08]: 0x0004c000 0 0 0 0
ath10k_pci 0000:01:00.0: [09]: 0x0004c400 0 0 0 0
ath10k_pci 0000:01:00.0: [10]: 0x0004c800 0 0 0 0
ath10k_pci 0000:01:00.0: [11]: 0x0004cc00 0 0 0 0
Tested HW: QCA9984,QCA9887,WCN3990
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Helen Koike [Fri, 17 May 2019 17:20:11 +0000 (13:20 -0400)]
media: vimc: fix component match compare
[ Upstream commit
ee1c71a8e1456ab53fe667281d855849edf26a4d ]
If the system has other devices being registered in the component
framework, the compare function will be called with a device that
doesn't belong to vimc.
This device is not necessarily a platform_device, nor have a
platform_data (which causes a NULL pointer dereference error) and if it
does have a pdata, it is not necessarily type of struct vimc_platform_data.
So casting to any of these types is wrong.
Instead of expecting a given pdev with a given pdata, just expect for
the device it self. vimc-core is the one who creates them, we know in
advance exactly which object to expect in the match.
Fixes:
4a29b7090749 ("[media] vimc: Subdevices as modules")
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ido Schimmel [Tue, 11 Jun 2019 07:19:41 +0000 (10:19 +0300)]
mlxsw: spectrum_router: Refresh nexthop neighbour when it becomes dead
[ Upstream commit
83d5782681cc12b3d485a83cb34c46b2445f510c ]
The driver tries to periodically refresh neighbours that are used to
reach nexthops. This is done by periodically calling neigh_event_send().
However, if the neighbour becomes dead, there is nothing we can do to
return it to a connected state and the above function call is basically
a NOP.
This results in the nexthop never being written to the device's
adjacency table and therefore never used to forward packets.
Fix this by dropping our reference from the dead neighbour and
associating the nexthop with a new neigbhour which we will try to
refresh.
Fixes:
a7ff87acd995 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Lindgren [Sun, 7 Apr 2019 18:12:50 +0000 (11:12 -0700)]
power: supply: cpcap-battery: Fix signed counter sample register
[ Upstream commit
c68b901ac4fa969db8917b6a9f9b40524a690d20 ]
The accumulator sample register is signed 32-bits wide register on
droid 4. And only the earlier version of cpcap has a signed 24-bits
wide register. We're currently passing it around as unsigned, so
let's fix that and use sign_extend32() for the earlier revision.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shirish S [Wed, 16 Jan 2019 15:10:40 +0000 (15:10 +0000)]
x86/MCE/AMD: Carve out the MC4_MISC thresholding quirk
[ Upstream commit
30aa3d26edb0f3d7992757287eec0ca588a5c259 ]
The MC4_MISC thresholding quirk needs to be applied during S5 -> S0 and
S3 -> S0 state transitions, which follow different code paths. Carve it
out into a separate function and call it mce_amd_feature_init() where
the two code paths of the state transitions converge.
[ bp: massage commit message and the carved out function. ]
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1547651417-23583-3-git-send-email-shirish.s@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shirish S [Thu, 10 Jan 2019 07:54:40 +0000 (07:54 +0000)]
x86/MCE/AMD: Turn off MC4_MISC thresholding on all family 0x15 models
[ Upstream commit
c95b323dcd3598dd7ef5005d6723c1ba3b801093 ]
MC4_MISC thresholding is not supported on all family 0x15 processors,
hence skip the x86_model check when applying the quirk.
[ bp: massage commit message. ]
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1547106849-3476-2-git-send-email-shirish.s@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luo Jiaxing [Fri, 25 Jan 2019 14:22:34 +0000 (22:22 +0800)]
scsi: hisi_sas: Reject setting programmed minimum linkrate > 1.5G
[ Upstream commit
eb44e4d7b5a3090f0114927f42ae575c29664a09 ]
The SAS controller cannot support a programmed minimum linkrate of > 1.5G
(it will always negotiate to 1.5G at least), so just reject it.
This solves a strange situation where the PHY negotiated linkrate may be
less than the programmed minimum linkrate.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xiang Chen [Fri, 25 Jan 2019 14:22:30 +0000 (22:22 +0800)]
scsi: hisi_sas: send primitive NOTIFY to SSP situation only
[ Upstream commit
569eddcf3a0f4efff4ef96a7012010e0f7daa8b4 ]
Send primitive NOTIFY to SSP situation only, or it causes underflow issue
when sending IO. Also rename hisi_sas_hw.sl_notify() to hisi_sas_hw.
sl_notify_ssp().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yonglong Liu [Wed, 20 Feb 2019 02:32:41 +0000 (10:32 +0800)]
net: hns3: Check variable is valid before assigning it to another
[ Upstream commit
676131f7c53ecdd79e29fc8cfcdefe6f9f2485e8 ]
In hnae3_register_ae_dev(), ae_algo->ops is assigned to ae_dev->ops
before check that ae_algo->ops is valid.
And in hnae3_register_ae_algo(), missing check for ae_algo->ops.
This patch fixes them.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Huazhong Tan [Wed, 30 Jan 2019 20:55:44 +0000 (04:55 +0800)]
net: hns3: change hnae3_register_ae_dev() to int
[ Upstream commit
74354140a579008fd164241e3697d9c37e5b8989 ]
hnae3_register_ae_dev() may fail, and it should return a error code
to its caller, so change hnae3_register_ae_dev() return type to int.
Also, when hnae3_register_ae_dev() return error, hns3_probe() should
do some error handling and return the error code.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jian Shen [Sat, 26 Jan 2019 16:49:11 +0000 (00:49 +0800)]
net: hns3: clear pci private data when unload hns3 driver
[ Upstream commit
ac864c2346d087dd3739435af1b8d36be5f60c75 ]
When unload hns3 driver, we should clear the pci private data.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Karsten Graul [Wed, 30 Jan 2019 17:51:05 +0000 (18:51 +0100)]
net/smc: do not wait under send_lock
[ Upstream commit
33f3fcc290671590821ff3c0c9396db1ec9b7d4c ]
smc_cdc_get_free_slot() might wait for free transfer buffers when using
SMC-R. This wait should not be done under the send_lock, which is a
spin_lock. This fixes a cpu loop in parallel threads waiting for the
send_lock.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Toke Høiland-Jørgensen [Wed, 9 Jan 2019 16:09:44 +0000 (17:09 +0100)]
sch_cake: Correctly update parent qlen when splitting GSO packets
[ Upstream commit
8c6c37fdc20ec9ffaa342f827a8e20afe736fb0c ]
To ensure parent qdiscs have the same notion of the number of enqueued
packets even after splitting a GSO packet, update the qdisc tree with the
number of packets that was added due to the split.
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stefano Stabellini [Fri, 21 Dec 2018 23:06:32 +0000 (15:06 -0800)]
pvcalls-front: don't return error when the ring is full
[ Upstream commit
d90a1ca60a1eccb4383fe203c76223ab4c0799ed ]
When the ring is full, size == array_size. It is not an error condition,
so simply return 0 instead of an error.
Signed-off-by: Stefano Stabellini <stefanos@xilinx.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
YueHaibing [Mon, 19 Nov 2018 12:48:19 +0000 (20:48 +0800)]
e100: Fix passing zero to 'PTR_ERR' warning in e100_load_ucode_wait
[ Upstream commit
cd0d465bb697a9c7bf66a9fe940f7981232f1676 ]
Fix a static code checker warning:
drivers/net/ethernet/intel/e100.c:1349
e100_load_ucode_wait() warn: passing zero to 'PTR_ERR'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan Chancellor [Thu, 20 Dec 2018 16:23:44 +0000 (17:23 +0100)]
drbd: Change drbd_request_detach_interruptible's return type to int
[ Upstream commit
5816a0932b4fd74257b8cc5785bc8067186a8723 ]
Clang warns when an implicit conversion is done between enumerated
types:
drivers/block/drbd/drbd_state.c:708:8: warning: implicit conversion from
enumeration type 'enum drbd_ret_code' to different enumeration type
'enum drbd_state_rv' [-Wenum-conversion]
rv = ERR_INTR;
~ ^~~~~~~~
drbd_request_detach_interruptible's only call site is in the return
statement of adm_detach, which returns an int. Change the return type of
drbd_request_detach_interruptible to match, silencing Clang's warning.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 30 Nov 2018 00:09:38 +0000 (16:09 -0800)]
scsi: lpfc: Correct topology type reporting on G7 adapters
[ Upstream commit
76558b25733140a0c6bd53ea8af04b2811c92ec3 ]
Driver missed classifying the chip type for G7 when reporting supported
topologies. This resulted in loop being shown as supported on FC links that
are not supported per the standard.
Add the chip classifications to the topology checks in the driver.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 30 Nov 2018 00:09:37 +0000 (16:09 -0800)]
scsi: lpfc: Correct code setting non existent bits in sli4 ABORT WQE
[ Upstream commit
1c36833d82ff24d0d54215fd956e7cc30fffce54 ]
Driver is setting bits in word 10 of the SLI4 ABORT WQE (the wqid). The
field was a carry over from a prior SLI revision. The field does not exist
in SLI4, and the action may result in an overlap with future definition of
the WQE.
Remove the setting of WQID in the ABORT WQE.
Also cleaned up WQE field settings - initialize to zero, don't bother to
set fields to zero.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 30 Nov 2018 00:09:33 +0000 (16:09 -0800)]
scsi: lpfc: Cap NPIV vports to 256
[ Upstream commit
8b47ae69e049ae0b3373859d901f0334322f9fe9 ]
Depending on the chipset, the number of NPIV vports may vary and be in
excess of what most switches support (256). To avoid confusion with the
users, limit the reported NPIV vports to 256.
Additionally correct the 16G adapter which is reporting a bogus NPIV vport
number if the link is down.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
H. Nikolaus Schaller [Thu, 7 Nov 2019 10:30:39 +0000 (11:30 +0100)]
omap: pdata-quirks: remove openpandora quirks for mmc3 and wl1251
[ Upstream commit
2398c41d64321e62af54424fd399964f3d48cdc2 ]
With a wl1251 child node of mmc3 in the device tree decoded
in omap_hsmmc.c to handle special wl1251 initialization, we do
no longer need to instantiate the mmc3 through pdata quirks.
We also can remove the wlan regulator and reset/interrupt definitions
and do them through device tree.
Fixes:
81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.7+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Wen Yang [Tue, 26 Nov 2019 14:04:52 +0000 (22:04 +0800)]
usb: typec: fix use after free in typec_register_port()
[ Upstream commit
5c388abefda0d92355714010c0199055c57ab6c7 ]
We can't use "port->sw" and/or "port->mux" after it has been freed.
Fixes:
23481121c81d ("usb: typec: class: Don't use port parent for getting mux handles")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: stable <stable@vger.kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191126140452.14048-1-wenyang@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mathias Nyman [Wed, 11 Dec 2019 14:20:07 +0000 (16:20 +0200)]
xhci: make sure interrupts are restored to correct state
[ Upstream commit
bd82873f23c9a6ad834348f8b83f3b6a5bca2c65 ]
spin_unlock_irqrestore() might be called with stale flags after
reading port status, possibly restoring interrupts to a incorrect
state.
If a usb2 port just finished resuming while the port status is read
the spin lock will be temporary released and re-acquired in a separate
function. The flags parameter is passed as value instead of a pointer,
not updating flags properly before the final spin_unlock_irqrestore()
is called.
Cc: <stable@vger.kernel.org> # v3.12+
Fixes:
8b3d45705e54 ("usb: Fix xHCI host issues on remote wakeup.")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Quinn Tran [Tue, 5 Nov 2019 15:06:52 +0000 (07:06 -0800)]
scsi: qla2xxx: Fix SRB leak on switch command timeout
[ Upstream commit
af2a0c51b1205327f55a7e82e530403ae1d42cbb ]
when GPSC/GPDB switch command fails, driver just returns without doing a
proper cleanup. This patch fixes this memory leak by calling sp->free() in
the error path.
Link: https://lore.kernel.org/r/20191105150657.8092-4-hmadhani@marvell.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Himanshu Madhani [Fri, 30 Aug 2019 22:23:57 +0000 (15:23 -0700)]
scsi: qla2xxx: Fix message indicating vectors used by driver
[ Upstream commit
da48b82425b8bf999fb9f7c220e967c4d661b5f8 ]
This patch updates log message which indicates number of vectors used by
the driver instead of displaying failure to get maximum requested
vectors. Driver will always request maximum vectors during
initialization. In the event driver is not able to get maximum requested
vectors, it will adjust the allocated vectors. This is normal and does not
imply failure in driver.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Link: https://lore.kernel.org/r/20190830222402.23688-2-hmadhani@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Fri, 9 Aug 2019 03:01:52 +0000 (20:01 -0700)]
scsi: qla2xxx: Always check the qla2x00_wait_for_hba_online() return value
[ Upstream commit
e6803efae5acd109fad9f2f07dab674563441a53 ]
This patch fixes several Coverity complaints about not always checking
the qla2x00_wait_for_hba_online() return value.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Fri, 9 Aug 2019 03:01:48 +0000 (20:01 -0700)]
scsi: qla2xxx: Fix qla24xx_process_bidir_cmd()
[ Upstream commit
c29282c65d1cf54daeea63be46243d7f69d72f4d ]
Set the r??_data_len variables before using these instead of after.
This patch fixes the following Coverity complaint:
const: At condition req_data_len != rsp_data_len, the value of req_data_len
must be equal to 0.
const: At condition req_data_len != rsp_data_len, the value of rsp_data_len
must be equal to 0.
dead_error_condition: The condition req_data_len != rsp_data_len cannot be
true.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes:
a9b6f722f62d ("[SCSI] qla2xxx: Implementation of bidirectional.") # v3.7.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Fri, 9 Aug 2019 03:01:40 +0000 (20:01 -0700)]
scsi: qla2xxx: Fix session lookup in qlt_abort_work()
[ Upstream commit
ac452b8e79320c9e90c78edf32ba2d42431e4daf ]
Pass the correct session ID to find_sess_by_s_id() instead of passing an
uninitialized variable.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes:
2d70c103fd2a ("[SCSI] qla2xxx: Add LLD target-mode infrastructure for >= 24xx series") # v3.5.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Quinn Tran [Fri, 26 Jul 2019 16:07:38 +0000 (09:07 -0700)]
scsi: qla2xxx: Fix hang in fcport delete path
[ Upstream commit
f00b3428a801758243693e046b34226e92bc56b3 ]
A hang was observed in the fcport delete path when the device was
responding slow and an issue-lip path (results in session termination) was
taken.
Fix this by issuing logo requests unconditionally.
PID: 19491 TASK:
ffff8e23e67bb150 CPU: 0 COMMAND: "kworker/0:0"
#0 [
ffff8e2370297bf8] __schedule at
ffffffffb4f7dbb0
#1 [
ffff8e2370297c88] schedule at
ffffffffb4f7e199
#2 [
ffff8e2370297c98] schedule_timeout at
ffffffffb4f7ba68
#3 [
ffff8e2370297d40] msleep at
ffffffffb48ad9ff
#4 [
ffff8e2370297d58] qlt_free_session_done at
ffffffffc0c32052 [qla2xxx]
#5 [
ffff8e2370297e20] process_one_work at
ffffffffb48bcfdf
#6 [
ffff8e2370297e68] worker_thread at
ffffffffb48bdca6
#7 [
ffff8e2370297ec8] kthread at
ffffffffb48c4f81
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Himanshu Madhani [Fri, 26 Jul 2019 16:07:26 +0000 (09:07 -0700)]
scsi: qla2xxx: Fix DMA unmap leak
[ Upstream commit
5d328de64d89400dcf9911125844d8adc0db697f ]
With debug kernel we see following wanings indicating memory leak.
[28809.523959] WARNING: CPU: 3 PID: 6790 at lib/dma-debug.c:978
dma_debug_device_change+0x166/0x1d0
[28809.523964] pci 0000:0c:00.6: DMA-API: device driver has pending DMA
allocations while released from device [count=5]
[28809.523964] One of leaked entries details: [device
address=0x00000002aefe4000] [size=8208 bytes] [mapped with DMA_BIDIRECTIONAL]
[mapped as coherent]
Fix this by unmapping DMA memory.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steffen Maier [Fri, 25 Oct 2019 16:12:53 +0000 (18:12 +0200)]
scsi: zfcp: trace channel log even for FCP command responses
[ Upstream commit
100843f176109af94600e500da0428e21030ca7f ]
While v2.6.26 commit
b75db73159cc ("[SCSI] zfcp: Add qtcb dump to hba debug
trace") is right that we don't want to flood the (payload) trace ring
buffer, we don't trace successful FCP command responses by default. So we
can include the channel log for problem determination with failed responses
of any FSF request type.
Fixes:
b75db73159cc ("[SCSI] zfcp: Add qtcb dump to hba debug trace")
Fixes:
a54ca0f62f95 ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.")
Cc: <stable@vger.kernel.org> #2.6.38+
Link: https://lore.kernel.org/r/e37597b5c4ae123aaa85fd86c23a9f71e994e4a9.1572018132.git.bblock@linux.ibm.com
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ming Lei [Fri, 30 Nov 2018 16:38:18 +0000 (00:38 +0800)]
block: fix single range discard merge
commit
2a5cf35cd6c56b2924bce103413ad3381bdc31fa upstream.
There are actually two kinds of discard merge:
- one is the normal discard merge, just like normal read/write request,
and call it single-range discard
- another is the multi-range discard, queue_max_discard_segments(rq->q) > 1
For the former case, queue_max_discard_segments(rq->q) is 1, and we
should handle this kind of discard merge like the normal read/write
request.
This patch fixes the following kernel panic issue[1], which is caused by
not removing the single-range discard request from elevator queue.
Guangwu has one raid discard test case, in which this issue is a bit
easier to trigger, and I verified that this patch can fix the kernel
panic issue in Guangwu's test case.
[1] kernel panic log from Jens's report
BUG: unable to handle kernel NULL pointer dereference at
0000000000000148
PGD 0 P4D 0.
Oops: 0000 [#1] SMP PTI
CPU: 37 PID: 763 Comm: kworker/37:1H Not tainted \
4.20.0-rc3-00649-ge64d9a554a91-dirty #14 Hardware name: Wiwynn \
Leopard-Orv2/Leopard-DDR BW, BIOS LBM08 03/03/2017 Workqueue: kblockd \
blk_mq_run_work_fn RIP: \
0010:blk_mq_get_driver_tag+0x81/0x120 Code: 24 \
10 48 89 7c 24 20 74 21 83 fa ff 0f 95 c0 48 8b 4c 24 28 65 48 33 0c 25 28 00 00 00 \
0f 85 96 00 00 00 48 83 c4 30 5b 5d c3 <48> 8b 87 48 01 00 00 8b 40 04 39 43 20 72 37 \
f6 87 b0 00 00 00 02 RSP: 0018:
ffffc90004aabd30 EFLAGS:
00010246 \
RAX:
0000000000000003 RBX:
ffff888465ea1300 RCX:
ffffc90004aabde8
RDX:
00000000ffffffff RSI:
ffffc90004aabde8 RDI:
0000000000000000
RBP:
0000000000000000 R08:
ffff888465ea1348 R09:
0000000000000000
R10:
0000000000001000 R11:
00000000ffffffff R12:
ffff888465ea1300
R13:
0000000000000000 R14:
ffff888465ea1348 R15:
ffff888465d10000
FS:
0000000000000000(0000) GS:
ffff88846f9c0000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000148 CR3:
000000000220a003 CR4:
00000000003606e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
blk_mq_dispatch_rq_list+0xec/0x480
? elv_rb_del+0x11/0x30
blk_mq_do_dispatch_sched+0x6e/0xf0
blk_mq_sched_dispatch_requests+0xfa/0x170
__blk_mq_run_hw_queue+0x5f/0xe0
process_one_work+0x154/0x350
worker_thread+0x46/0x3c0
kthread+0xf5/0x130
? process_one_work+0x350/0x350
? kthread_destroy_worker+0x50/0x50
ret_from_fork+0x1f/0x30
Modules linked in: sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel \
kvm switchtec irqbypass iTCO_wdt iTCO_vendor_support efivars cdc_ether usbnet mii \
cdc_acm i2c_i801 lpc_ich mfd_core ipmi_si ipmi_devintf ipmi_msghandler acpi_cpufreq \
button sch_fq_codel nfsd nfs_acl lockd grace auth_rpcgss oid_registry sunrpc nvme \
nvme_core fuse sg loop efivarfs autofs4 CR2:
0000000000000148 \
---[ end trace
340a1fb996df1b9b ]---
RIP: 0010:blk_mq_get_driver_tag+0x81/0x120
Code: 24 10 48 89 7c 24 20 74 21 83 fa ff 0f 95 c0 48 8b 4c 24 28 65 48 33 0c 25 28 \
00 00 00 0f 85 96 00 00 00 48 83 c4 30 5b 5d c3 <48> 8b 87 48 01 00 00 8b 40 04 39 43 \
20 72 37 f6 87 b0 00 00 00 02
Fixes:
445251d0f4d329a ("blk-mq: fix discard merge with scheduler attached")
Reported-by: Jens Axboe <axboe@kernel.dk>
Cc: Guangwu Zhang <guazhang@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Andre Tomt <andre@tomt.net>
Cc: Jack Wang <jack.wang.usish@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeff Mahoney [Thu, 24 Oct 2019 14:31:27 +0000 (10:31 -0400)]
reiserfs: fix extended attributes on the root directory
commit
60e4cf67a582d64f07713eda5fcc8ccdaf7833e6 upstream.
Since commit
d0a5b995a308 (vfs: Add IOP_XATTR inode operations flag)
extended attributes haven't worked on the root directory in reiserfs.
This is due to reiserfs conditionally setting the sb->s_xattrs handler
array depending on whether it located or create the internal privroot
directory. It necessarily does this after the root inode is already
read in. The IOP_XATTR flag is set during inode initialization, so
it never gets set on the root directory.
This commit unconditionally assigns sb->s_xattrs and clears IOP_XATTR on
internal inodes. The old return values due to the conditional assignment
are handled via open_xa_root, which now returns EOPNOTSUPP as the VFS
would have done.
Link: https://lore.kernel.org/r/20191024143127.17509-1-jeffm@suse.com
CC: stable@vger.kernel.org
Fixes:
d0a5b995a308 ("vfs: Add IOP_XATTR inode operations flag")
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Tue, 5 Nov 2019 16:44:12 +0000 (17:44 +0100)]
ext4: Fix credit estimate for final inode freeing
commit
65db869c754e7c271691dd5feabf884347e694f5 upstream.
Estimate for the number of credits needed for final freeing of inode in
ext4_evict_inode() was to small. We may modify 4 blocks (inode & sb for
orphan deletion, bitmap & group descriptor for inode freeing) and not
just 3.
[ Fixed minor whitespace nit. -- TYT ]
Fixes:
e50e5129f384 ("ext4: xattr-in-inode support")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20191105164437.32602-6-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Monakhov [Thu, 31 Oct 2019 10:39:19 +0000 (10:39 +0000)]
quota: fix livelock in dquot_writeback_dquots
commit
6ff33d99fc5c96797103b48b7b0902c296f09c05 upstream.
Write only quotas which are dirty at entry.
XFSTEST: https://github.com/dmonakhov/xfstests/commit/
b10ad23566a5bf75832a6f500e1236084083cddc
Link: https://lore.kernel.org/r/20191031103920.3919-1-dmonakhov@openvz.org
CC: stable@vger.kernel.org
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Dmitry Monakhov <dmtrmonakhov@yandex-team.ru>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chengguang Xu [Tue, 5 Nov 2019 04:51:00 +0000 (12:51 +0800)]
ext2: check err when partial != NULL
commit
e705f4b8aa27a59f8933e8f384e9752f052c469c upstream.
Check err when partial == NULL is meaningless because
partial == NULL means getting branch successfully without
error.
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191105045100.7104-1-cgxu519@mykernel.net
Signed-off-by: Chengguang Xu <cgxu519@mykernel.net>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Monakhov [Thu, 31 Oct 2019 10:39:20 +0000 (10:39 +0000)]
quota: Check that quota is not dirty before release
commit
df4bb5d128e2c44848aeb36b7ceceba3ac85080d upstream.
There is a race window where quota was redirted once we drop dq_list_lock inside dqput(),
but before we grab dquot->dq_lock inside dquot_release()
TASK1 TASK2 (chowner)
->dqput()
we_slept:
spin_lock(&dq_list_lock)
if (dquot_dirty(dquot)) {
spin_unlock(&dq_list_lock);
dquot->dq_sb->dq_op->write_dquot(dquot);
goto we_slept
if (test_bit(DQ_ACTIVE_B, &dquot->dq_flags)) {
spin_unlock(&dq_list_lock);
dquot->dq_sb->dq_op->release_dquot(dquot);
dqget()
mark_dquot_dirty()
dqput()
goto we_slept;
}
So dquot dirty quota will be released by TASK1, but on next we_sleept loop
we detect this and call ->write_dquot() for it.
XFSTEST: https://github.com/dmonakhov/xfstests/commit/
440a80d4cbb39e9234df4d7240aee1d551c36107
Link: https://lore.kernel.org/r/20191031103920.3919-2-dmonakhov@openvz.org
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Monakhov <dmtrmonakhov@yandex-team.ru>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ville Syrjälä [Thu, 19 Sep 2019 13:28:53 +0000 (16:28 +0300)]
video/hdmi: Fix AVI bar unpack
commit
6039f37dd6b76641198e290f26b31c475248f567 upstream.
The bar values are little endian, not big endian. The pack
function did it right but the unpack got it wrong. Fix it.
Cc: stable@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixes:
2c676f378edb ("[media] hdmi: added unpack and logging functions for InfoFrames")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919132853.30954-1-ville.syrjala@linux.intel.com
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cédric Le Goater [Tue, 3 Dec 2019 16:36:42 +0000 (17:36 +0100)]
powerpc/xive: Skip ioremap() of ESB pages for LSI interrupts
commit
b67a95f2abff0c34e5667c15ab8900de73d8d087 upstream.
The PCI INTx interrupts and other LSI interrupts are handled differently
under a sPAPR platform. When the interrupt source characteristics are
queried, the hypervisor returns an H_INT_ESB flag to inform the OS
that it should be using the H_INT_ESB hcall for interrupt management
and not loads and stores on the interrupt ESB pages.
A default -1 value is returned for the addresses of the ESB pages. The
driver ignores this condition today and performs a bogus IO mapping.
Recent changes and the DEBUG_VM configuration option make the bug
visible with :
kernel BUG at arch/powerpc/include/asm/book3s/64/pgtable.h:612!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Radix MMU=Hash SMP NR_CPUS=1024 NUMA pSeries
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.0-0.rc6.git0.1.fc32.ppc64le #1
NIP:
c000000000f63294 LR:
c000000000f62e44 CTR:
0000000000000000
REGS:
c0000000fa45f0d0 TRAP: 0700 Not tainted (5.4.0-0.rc6.git0.1.fc32.ppc64le)
...
NIP ioremap_page_range+0x4c4/0x6e0
LR ioremap_page_range+0x74/0x6e0
Call Trace:
ioremap_page_range+0x74/0x6e0 (unreliable)
do_ioremap+0x8c/0x120
__ioremap_caller+0x128/0x140
ioremap+0x30/0x50
xive_spapr_populate_irq_data+0x170/0x260
xive_irq_domain_map+0x8c/0x170
irq_domain_associate+0xb4/0x2d0
irq_create_mapping+0x1e0/0x3b0
irq_create_fwspec_mapping+0x27c/0x3e0
irq_create_of_mapping+0x98/0xb0
of_irq_parse_and_map_pci+0x168/0x230
pcibios_setup_device+0x88/0x250
pcibios_setup_bus_devices+0x54/0x100
__of_scan_bus+0x160/0x310
pcibios_scan_phb+0x330/0x390
pcibios_init+0x8c/0x128
do_one_initcall+0x60/0x2c0
kernel_init_freeable+0x290/0x378
kernel_init+0x2c/0x148
ret_from_kernel_thread+0x5c/0x80
Fixes:
bed81ee181dd ("powerpc/xive: introduce H_INT_ESB hcall")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191203163642.2428-1-clg@kaod.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alastair D'Silva [Mon, 4 Nov 2019 02:32:53 +0000 (13:32 +1100)]
powerpc: Allow flush_icache_range to work across ranges >4GB
commit
29430fae82073d39b1b881a3cd507416a56a363f upstream.
When calling flush_icache_range with a size >4GB, we were masking
off the upper 32 bits, so we would incorrectly flush a range smaller
than intended.
This patch replaces the 32 bit shifts with 64 bit ones, so that
the full size is accounted for.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-2-alastair@au1.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cédric Le Goater [Thu, 31 Oct 2019 06:31:00 +0000 (07:31 +0100)]
powerpc/xive: Prevent page fault issues in the machine crash handler
commit
1ca3dec2b2dff9d286ce6cd64108bda0e98f9710 upstream.
When the machine crash handler is invoked, all interrupts are masked
but interrupts which have not been started yet do not have an ESB page
mapped in the Linux address space. This crashes the 'crash kexec'
sequence on sPAPR guests.
To fix, force the mapping of the ESB page when an interrupt is being
mapped in the Linux IRQ number space. This is done by setting the
initial state of the interrupt to OFF which is not necessarily the
case on PowerNV.
Fixes:
243e25112d06 ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191031063100.3864-1-clg@kaod.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alastair D'Silva [Mon, 4 Nov 2019 02:32:54 +0000 (13:32 +1100)]
powerpc: Allow 64bit VDSO __kernel_sync_dicache to work across ranges >4GB
commit
f9ec11165301982585e5e5f606739b5bae5331f3 upstream.
When calling __kernel_sync_dicache with a size >4GB, we were masking
off the upper 32 bits, so we would incorrectly flush a range smaller
than intended.
This patch replaces the 32 bit shifts with 64 bit ones, so that
the full size is accounted for.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-3-alastair@au1.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Fri, 8 Nov 2019 20:34:30 +0000 (21:34 +0100)]
ppdev: fix PPGETTIME/PPSETTIME ioctls
commit
998174042da229e2cf5841f574aba4a743e69650 upstream.
Going through the uses of timeval in the user space API,
I noticed two bugs in ppdev that were introduced in the y2038
conversion:
* The range check was accidentally moved from ppsettime to
ppgettime
* On sparc64, the microseconds are in the other half of the
64-bit word.
Fix both, and mark the fix for stable backports.
Cc: stable@vger.kernel.org
Fixes:
3b9ab374a1e6 ("ppdev: convert to y2038 safe")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191108203435.112759-8-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jarkko Nikula [Sat, 16 Nov 2019 15:16:51 +0000 (17:16 +0200)]
ARM: dts: omap3-tao3530: Fix incorrect MMC card detection GPIO polarity
commit
287897f9aaa2ad1c923d9875914f57c4dc9159c8 upstream.
The MMC card detection GPIO polarity is active low on TAO3530, like in many
other similar boards. Now the card is not detected and it is unable to
mount rootfs from an SD card.
Fix this by using the correct polarity.
This incorrect polarity was defined already in the commit
30d95c6d7092
("ARM: dts: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi") in v3.18
kernel and later changed to use defined GPIO constants in v4.4 kernel by
the commit
3a637e008e54 ("ARM: dts: Use defined GPIO constants in flags
cell for OMAP2+ boards").
While the latter commit did not introduce the issue I'm marking it with
Fixes tag due the v4.4 kernels still being maintained.
Fixes:
3a637e008e54 ("ARM: dts: Use defined GPIO constants in flags cell for OMAP2+ boards")
Cc: linux-stable <stable@vger.kernel.org> # 4.4+
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H. Nikolaus Schaller [Thu, 7 Nov 2019 10:30:37 +0000 (11:30 +0100)]
mmc: host: omap_hsmmc: add code for special init of wl1251 to get rid of pandora_wl1251_init_card
commit
f6498b922e57aecbe3b7fa30a308d9d586c0c369 upstream.
Pandora_wl1251_init_card was used to do special pdata based
setup of the sdio mmc interface. This does no longer work with
v4.7 and later. A fix requires a device tree based mmc3 setup.
Therefore we move the special setup to omap_hsmmc.c instead
of calling some pdata supplied init_card function.
The new code checks for a DT child node compatible to wl1251
so it will not affect other MMC3 use cases.
Generally, this code was and still is a hack and should be
moved to mmc core to e.g. read such properties from optional
DT child nodes.
Fixes:
81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.7+
[Ulf: Fixed up some checkpatch complaints]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Mon, 5 Aug 2019 16:27:09 +0000 (18:27 +0200)]
pinctrl: samsung: Fix device node refcount leaks in S3C64xx wakeup controller init
commit
7f028caadf6c37580d0f59c6c094ed09afc04062 upstream.
In s3c64xx_eint_eint0_init() the for_each_child_of_node() loop is used
with a break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes:
61dd72613177 ("pinctrl: Add pinctrl-s3c64xx driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Mon, 5 Aug 2019 16:27:10 +0000 (18:27 +0200)]
pinctrl: samsung: Fix device node refcount leaks in init code
commit
a322b3377f4bac32aa25fb1acb9e7afbbbbd0137 upstream.
Several functions use for_each_child_of_node() loop with a break to find
a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes:
9a2c1c3b91aa ("pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Mon, 5 Aug 2019 16:27:08 +0000 (18:27 +0200)]
pinctrl: samsung: Fix device node refcount leaks in S3C24xx wakeup controller init
commit
6fbbcb050802d6ea109f387e961b1dbcc3a80c96 upstream.
In s3c24xx_eint_init() the for_each_child_of_node() loop is used with a
break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes:
af99a7507469 ("pinctrl: Add pinctrl-s3c24xx driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Mon, 5 Aug 2019 16:27:07 +0000 (18:27 +0200)]
pinctrl: samsung: Fix device node refcount leaks in Exynos wakeup controller init
commit
5c7f48dd14e892e3e920dd6bbbd52df79e1b3b41 upstream.
In exynos_eint_wkup_init() the for_each_child_of_node() loop is used
with a break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes:
43b169db1841 ("pinctrl: add exynos4210 specific extensions for samsung pinctrl driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nishka Dasgupta [Sun, 4 Aug 2019 16:02:00 +0000 (21:32 +0530)]
pinctrl: samsung: Add of_node_put() before return in error path
commit
3d2557ab75d4c568c79eefa2e550e0d80348a6bd upstream.
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return of
exynos_eint_wkup_init() error path.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes:
14c255d35b25 ("pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gregory CLEMENT [Fri, 15 Nov 2019 15:57:52 +0000 (16:57 +0100)]
pinctrl: armada-37xx: Fix irq mask access in armada_37xx_irq_set_type()
commit
04fb02757ae5188031eb71b2f6f189edb1caf5dc upstream.
As explained in the following commit
a9a1a4833613 ("pinctrl:
armada-37xx: Fix gpio interrupt setup") the armada_37xx_irq_set_type()
function can be called before the initialization of the mask field.
That means that we can't use this field in this function and need to
workaround it using hwirq.
Fixes:
30ac0d3b0702 ("pinctrl: armada-37xx: Add edge both type gpio irq support")
Cc: stable@vger.kernel.org
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191115155752.2562-1-gregory.clement@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafael J. Wysocki [Wed, 4 Dec 2019 01:54:27 +0000 (02:54 +0100)]
ACPI: PM: Avoid attaching ACPI PM domain to certain devices
commit
b9ea0bae260f6aae546db224daa6ac1bd9d94b91 upstream.
Certain ACPI-enumerated devices represented as platform devices in
Linux, like fans, require special low-level power management handling
implemented by their drivers that is not in agreement with the ACPI
PM domain behavior. That leads to problems with managing ACPI fans
during system-wide suspend and resume.
For this reason, make acpi_dev_pm_attach() skip the affected devices
by adding a list of device IDs to avoid to it and putting the IDs of
the affected devices into that list.
Fixes:
e5cc8ef31267 (ACPI / PM: Provide ACPI PM callback routines for subsystems)
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vamshi K Sthambamkadi [Thu, 28 Nov 2019 10:28:29 +0000 (15:58 +0530)]
ACPI: bus: Fix NULL pointer check in acpi_bus_get_private_data()
commit
627ead724eff33673597216f5020b72118827de4 upstream.
kmemleak reported backtrace:
[<
bbee0454>] kmem_cache_alloc_trace+0x128/0x260
[<
6677f215>] i2c_acpi_install_space_handler+0x4b/0xe0
[<
1180f4fc>] i2c_register_adapter+0x186/0x400
[<
6083baf7>] i2c_add_adapter+0x4e/0x70
[<
a3ddf966>] intel_gmbus_setup+0x1a2/0x2c0 [i915]
[<
84cb69ae>] i915_driver_probe+0x8d8/0x13a0 [i915]
[<
81911d4b>] i915_pci_probe+0x48/0x160 [i915]
[<
4b159af1>] pci_device_probe+0xdc/0x160
[<
b3c64704>] really_probe+0x1ee/0x450
[<
bc029f5a>] driver_probe_device+0x142/0x1b0
[<
d8829d20>] device_driver_attach+0x49/0x50
[<
de71f045>] __driver_attach+0xc9/0x150
[<
df33ac83>] bus_for_each_dev+0x56/0xa0
[<
80089bba>] driver_attach+0x19/0x20
[<
cc73f583>] bus_add_driver+0x177/0x220
[<
7b29d8c7>] driver_register+0x56/0xf0
In i2c_acpi_remove_space_handler(), a leak occurs whenever the
"data" parameter is initialized to 0 before being passed to
acpi_bus_get_private_data().
This is because the NULL pointer check in acpi_bus_get_private_data()
(condition->if(!*data)) returns EINVAL and, in consequence, memory is
never freed in i2c_acpi_remove_space_handler().
Fix the NULL pointer check in acpi_bus_get_private_data() to follow
the analogous check in acpi_get_data_full().
Signed-off-by: Vamshi K Sthambamkadi <vamshi.k.sthambamkadi@gmail.com>
[ rjw: Subject & changelog ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Francesco Ruggeri [Wed, 20 Nov 2019 05:47:27 +0000 (21:47 -0800)]
ACPI: OSL: only free map once in osl.c
commit
833a426cc471b6088011b3d67f1dc4e147614647 upstream.
acpi_os_map_cleanup checks map->refcount outside of acpi_ioremap_lock
before freeing the map. This creates a race condition the can result
in the map being freed more than once.
A panic can be caused by running
for ((i=0; i<10; i++))
do
for ((j=0; j<100000; j++))
do
cat /sys/firmware/acpi/tables/data/BERT >/dev/null
done &
done
This patch makes sure that only the process that drops the reference
to 0 does the freeing.
Fixes:
b7c1fadd6c2e ("ACPI: Do not use krefs under a mutex in osl.c")
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika Westerberg [Wed, 30 Oct 2019 15:05:45 +0000 (18:05 +0300)]
ACPI / hotplug / PCI: Allocate resources directly under the non-hotplug bridge
commit
77adf9355304f8dcf09054280af5e23fc451ab3d upstream.
Valerio and others reported that commit
84c8b58ed3ad ("ACPI / hotplug /
PCI: Don't scan bridges managed by native hotplug") prevents some recent
LG and HP laptops from booting with endless loop of:
ACPI Error: No handler or method for GPE 08, disabling event (
20190215/evgpe-835)
ACPI Error: No handler or method for GPE 09, disabling event (
20190215/evgpe-835)
ACPI Error: No handler or method for GPE 0A, disabling event (
20190215/evgpe-835)
...
What seems to happen is that during boot, after the initial PCI enumeration
when EC is enabled the platform triggers ACPI Notify() to one of the root
ports. The root port itself looks like this:
pci 0000:00:1b.0: PCI bridge to [bus 02-3a]
pci 0000:00:1b.0: bridge window [mem 0xc4000000-0xda0fffff]
pci 0000:00:1b.0: bridge window [mem 0x80000000-0xa1ffffff 64bit pref]
The BIOS has configured the root port so that it does not have I/O bridge
window.
Now when the ACPI Notify() is triggered ACPI hotplug handler calls
acpiphp_native_scan_bridge() for each non-hotplug bridge (as this system is
using native PCIe hotplug) and pci_assign_unassigned_bridge_resources() to
allocate resources.
The device connected to the root port is a PCIe switch (Thunderbolt
controller) with two hotplug downstream ports. Because of the hotplug ports
__pci_bus_size_bridges() tries to add "additional I/O" of 256 bytes to each
(DEFAULT_HOTPLUG_IO_SIZE). This gets further aligned to 4k as that's the
minimum I/O window size so each hotplug port gets 4k I/O window and the
same happens for the root port (which is also hotplug port). This means
3 * 4k = 12k I/O window.
Because of this pci_assign_unassigned_bridge_resources() ends up opening a
I/O bridge window for the root port at first available I/O address which
seems to be in range 0x1000 - 0x3fff. Normally this range is used for ACPI
stuff such as GPE bits (below is part of /proc/ioports):
1800-1803 : ACPI PM1a_EVT_BLK
1804-1805 : ACPI PM1a_CNT_BLK
1808-180b : ACPI PM_TMR
1810-1815 : ACPI CPU throttle
1850-1850 : ACPI PM2_CNT_BLK
1854-1857 : pnp 00:05
1860-187f : ACPI GPE0_BLK
However, when the ACPI Notify() happened this range was not yet reserved
for ACPI/PNP (that happens later) so PCI gets it. It then starts writing to
this range and accidentally stomps over GPE bits among other things causing
the endless stream of messages about missing GPE handler.
This problem does not happen if "pci=hpiosize=0" is passed in the kernel
command line. The reason is that then the kernel does not try to allocate
the additional 256 bytes for each hotplug port.
Fix this by allocating resources directly below the non-hotplug bridges
where a new device may appear as a result of ACPI Notify(). This avoids the
hotplug bridges and prevents opening the additional I/O window.
Fixes:
84c8b58ed3ad ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203617
Link: https://lore.kernel.org/r/20191030150545.19885-1-mika.westerberg@linux.intel.com
Reported-by: Valerio Passini <passini.valerio@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John Hubbard [Thu, 31 Oct 2019 05:21:59 +0000 (22:21 -0700)]
cpufreq: powernv: fix stack bloat and hard limit on number of CPUs
commit
db0d32d84031188443e25edbd50a71a6e7ac5d1d upstream.
The following build warning occurred on powerpc 64-bit builds:
drivers/cpufreq/powernv-cpufreq.c: In function 'init_chip_info':
drivers/cpufreq/powernv-cpufreq.c:1070:1: warning: the frame size of
1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This is with a cross-compiler based on gcc 8.1.0, which I got from:
https://mirrors.edge.kernel.org/pub/tools/crosstool/files/bin/x86_64/8.1.0/
The warning is due to putting 1024 bytes on the stack:
unsigned int chip[256];
...and it's also undesirable to have a hard limit on the number of
CPUs here.
Fix both problems by dynamically allocating based on num_possible_cpus,
as recommended by Michael Ellerman.
Fixes:
053819e0bf840 ("cpufreq: powernv: Handle throttling due to Pmax capping at chip level")
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leonard Crestez [Tue, 24 Sep 2019 07:52:23 +0000 (10:52 +0300)]
PM / devfreq: Lock devfreq in trans_stat_show
commit
2abb0d5268ae7b5ddf82099b1f8d5aa8414637d4 upstream.
There is no locking in this sysfs show function so stats printing can
race with a devfreq_update_status called as part of freq switching or
with initialization.
Also add an assert in devfreq_update_status to make it clear that lock
must be held by caller.
Fixes:
39688ce6facd ("PM / devfreq: account suspend/resume for stats")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Shishkin [Wed, 20 Nov 2019 13:08:06 +0000 (15:08 +0200)]
intel_th: pci: Add Tiger Lake CPU support
commit
6e6c18bcb78c0dc0601ebe216bed12c844492d0c upstream.
This adds support for the Trace Hub in Tiger Lake CPU.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191120130806.44028-4-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Shishkin [Wed, 20 Nov 2019 13:08:05 +0000 (15:08 +0200)]
intel_th: pci: Add Ice Lake CPU support
commit
6a1743422a7c0fda26764a544136cac13e5ae486 upstream.
This adds support for the Trace Hub in Ice Lake CPU.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191120130806.44028-3-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Shishkin [Wed, 20 Nov 2019 13:08:04 +0000 (15:08 +0200)]
intel_th: Fix a double put_device() in error path
commit
512592779a337feb5905d8fcf9498dbf33672d4a upstream.
Commit
a753bfcfdb1f ("intel_th: Make the switch allocate its subdevices")
factored out intel_th_subdevice_alloc() from intel_th_populate(), but got
the error path wrong, resulting in two instances of a double put_device()
on a freshly initialized, but not 'added' device.
Fix this by only doing one put_device() in the error path.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes:
a753bfcfdb1f ("intel_th: Make the switch allocate its subdevices")
Reported-by: Wen Yang <wenyang@linux.alibaba.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org # v4.14+
Link: https://lore.kernel.org/r/20191120130806.44028-2-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gao Xiang [Sun, 1 Dec 2019 08:01:09 +0000 (16:01 +0800)]
erofs: zero out when listxattr is called with no xattr
commit
926d1650176448d7684b991fbe1a5b1a8289e97c upstream.
As David reported [1], ENODATA returns when attempting
to modify files by using EROFS as an overlayfs lower layer.
The root cause is that listxattr could return unexpected
-ENODATA by mistake for inodes without xattr. That breaks
listxattr return value convention and it can cause copy
up failure when used with overlayfs.
Resolve by zeroing out if no xattr is found for listxattr.
[1] https://lore.kernel.org/r/CAEvUa7nxnby+rxK-KRMA46=exeOMApkDMAV08AjMkkPnTPV4CQ@mail.gmail.com
Link: https://lore.kernel.org/r/20191201084040.29275-1-hsiangkao@aol.com
Fixes:
cadf1ccf1b00 ("staging: erofs: add error handling for xattr submodule")
Cc: <stable@vger.kernel.org> # 4.19+
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zhenzhong Duan [Wed, 23 Oct 2019 01:57:14 +0000 (09:57 +0800)]
cpuidle: Do not unset the driver if it is there already
commit
918c1fe9fbbe46fcf56837ff21f0ef96424e8b29 upstream.
Fix __cpuidle_set_driver() to check if any of the CPUs in the mask has
a driver different from drv already and, if so, return -EBUSY before
updating any cpuidle_drivers per-CPU pointers.
Fixes:
82467a5a885d ("cpuidle: simplify multiple driver support")
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans Verkuil [Mon, 16 Sep 2019 05:47:41 +0000 (02:47 -0300)]
media: cec.h: CEC_OP_REC_FLAG_ values were swapped
commit
806e0cdfee0b99efbb450f9f6e69deb7118602fc upstream.
CEC_OP_REC_FLAG_NOT_USED is 0 and CEC_OP_REC_FLAG_USED is 1, not the
other way around.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Jiunn Chang <c0d1n61at3@gmail.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 10 Oct 2019 13:13:32 +0000 (10:13 -0300)]
media: radio: wl1273: fix interrupt masking on release
commit
1091eb830627625dcf79958d99353c2391f41708 upstream.
If a process is interrupted while accessing the radio device and the
core lock is contended, release() could return early and fail to update
the interrupt mask.
Note that the return value of the v4l2 release file operation is
ignored.
Fixes:
87d1a50ce451 ("[media] V4L2: WL1273 FM Radio: TI WL1273 FM radio driver")
Cc: stable <stable@vger.kernel.org> # 2.6.38
Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 10 Oct 2019 13:13:31 +0000 (10:13 -0300)]
media: bdisp: fix memleak on release
commit
11609a7e21f8cea42630350aa57662928fa4dc63 upstream.
If a process is interrupted while accessing the video device and the
device lock is contended, release() could return early and fail to free
related resources.
Note that the return value of the v4l2 release file operation is
ignored.
Fixes:
28ffeebbb7bd ("[media] bdisp: 2D blitter driver using v4l2 mem2mem framework")
Cc: stable <stable@vger.kernel.org> # 4.2
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gerald Schaefer [Wed, 11 Sep 2019 17:42:23 +0000 (19:42 +0200)]
s390/mm: properly clear _PAGE_NOEXEC bit when it is not supported
commit
ab874f22d35a8058d8fdee5f13eb69d8867efeae upstream.
On older HW or under a hypervisor, w/o the instruction-execution-
protection (IEP) facility, and also w/o EDAT-1, a translation-specification
exception may be recognized when bit 55 of a pte is one (_PAGE_NOEXEC).
The current code tries to prevent setting _PAGE_NOEXEC in such cases,
by removing it within set_pte_at(). However, ptep_set_access_flags()
will modify a pte directly, w/o using set_pte_at(). There is at least
one scenario where this can result in an active pte with _PAGE_NOEXEC
set, which would then lead to a panic due to a translation-specification
exception (write to swapped out page):
do_swap_page
pte = mk_pte (with _PAGE_NOEXEC bit)
set_pte_at (will remove _PAGE_NOEXEC bit in page table, but keep it
in local variable pte)
vmf->orig_pte = pte (pte still contains _PAGE_NOEXEC bit)
do_wp_page
wp_page_reuse
entry = vmf->orig_pte (still with _PAGE_NOEXEC bit)
ptep_set_access_flags (writes entry with _PAGE_NOEXEC bit)
Fix this by clearing _PAGE_NOEXEC already in mk_pte_phys(), where the
pgprot value is applied, so that no pte with _PAGE_NOEXEC will ever be
visible, if it is not supported. The check in set_pte_at() can then also
be removed.
Cc: <stable@vger.kernel.org> # 4.11+
Fixes:
57d7f939e7bd ("s390: add no-execute support")
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Denis Efremov [Mon, 30 Sep 2019 20:31:47 +0000 (23:31 +0300)]
ar5523: check NULL before memcpy() in ar5523_cmd()
commit
315cee426f87658a6799815845788fde965ddaad upstream.
memcpy() call with "idata == NULL && ilen == 0" results in undefined
behavior in ar5523_cmd(). For example, NULL is passed in callchain
"ar5523_stat_work() -> ar5523_cmd_write() -> ar5523_cmd()". This patch
adds ilen check before memcpy() call in ar5523_cmd() to prevent an
undefined behavior.
Cc: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksa Sarai [Wed, 16 Oct 2019 15:50:01 +0000 (02:50 +1100)]
cgroup: pids: use atomic64_t for pids->limit
commit
a713af394cf382a30dd28a1015cbe572f1b9ca75 upstream.
Because pids->limit can be changed concurrently (but we don't want to
take a lock because it would be needlessly expensive), use atomic64_ts
instead.
Fixes: commit
49b786ea146f ("cgroup: implement the PIDs subsystem")
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ming Lei [Sat, 2 Nov 2019 08:02:15 +0000 (16:02 +0800)]
blk-mq: avoid sysfs buffer overflow with too many CPU cores
commit
8962842ca5abdcf98e22ab3b2b45a103f0408b95 upstream.
It is reported that sysfs buffer overflow can be triggered if the system
has too many CPU cores(>841 on 4K PAGE_SIZE) when showing CPUs of
hctx via /sys/block/$DEV/mq/$N/cpu_list.
Use snprintf to avoid the potential buffer overflow.
This version doesn't change the attribute format, and simply stops
showing CPU numbers if the buffer is going to overflow.
Cc: stable@vger.kernel.org
Fixes:
676141e48af7("blk-mq: don't dump CPU -> hw queue map on driver load")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Jeffery [Mon, 16 Sep 2019 17:15:14 +0000 (13:15 -0400)]
md: improve handling of bio with REQ_PREFLUSH in md_flush_request()
commit
775d78319f1ceb32be8eb3b1202ccdc60e9cb7f1 upstream.
If pers->make_request fails in md_flush_request(), the bio is lost. To
fix this, pass back a bool to indicate if the original make_request call
should continue to handle the I/O and instead of assuming the flush logic
will push it to completion.
Convert md_flush_request to return a bool and no longer calls the raid
driver's make_request function. If the return is true, then the md flush
logic has or will complete the bio and the md make_request call is done.
If false, then the md make_request function needs to keep processing like
it is a normal bio. Let the original call to md_handle_request handle any
need to retry sending the bio to the raid driver's make_request function
should it be needed.
Also mark md_flush_request and the make_request function pointer as
__must_check to issue warnings should these critical return values be
ignored.
Fixes:
2bc13b83e629 ("md: batch flush requests.")
Cc: stable@vger.kernel.org # # v4.19+
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pawel Harlozinski [Tue, 12 Nov 2019 13:02:36 +0000 (14:02 +0100)]
ASoC: Jack: Fix NULL pointer dereference in snd_soc_jack_report
commit
8f157d4ff039e03e2ed4cb602eeed2fd4687a58f upstream.
Check for existance of jack before tracing.
NULL pointer dereference has been reported by KASAN while unloading
machine driver (snd_soc_cnl_rt274).
Signed-off-by: Pawel Harlozinski <pawel.harlozinski@linux.intel.com>
Link: https://lore.kernel.org/r/20191112130237.10141-1-pawel.harlozinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jacob Rasmussen [Thu, 14 Nov 2019 23:20:11 +0000 (16:20 -0700)]
ASoC: rt5645: Fixed typo for buddy jack support.
commit
fe23be2d85b05f561431d75acddec726ea807d2a upstream.
Had a typo in
e7cfd867fd98 that resulted in buddy jack support not being
fixed.
Fixes:
e7cfd867fd98 ("ASoC: rt5645: Fixed buddy jack support.")
Signed-off-by: Jacob Rasmussen <jacobraz@google.com>
Reviewed-by: Ross Zwisler <zwisler@google.com>
Cc: <jacobraz@google.com>
CC: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191114232011.165762-1-jacobraz@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jacob Rasmussen [Mon, 11 Nov 2019 18:59:57 +0000 (11:59 -0700)]
ASoC: rt5645: Fixed buddy jack support.
commit
e7cfd867fd9842f346688f28412eb83dec342900 upstream.
The headphone jack on buddy was broken with the following commit:
commit
6b5da66322c5 ("ASoC: rt5645: read jd1_1 status for jd
detection").
This changes the jd_mode for buddy to 4 so buddy can read from the same
register that was used in the working version of this driver without
affecting any other devices that might use this, since no other device uses
jd_mode = 4. To test this I plugged and uplugged the headphone jack, verifying
audio works.
Signed-off-by: Jacob Rasmussen <jacobraz@google.com>
Reviewed-by: Ross Zwisler <zwisler@google.com>
Link: https://lore.kernel.org/r/20191111185957.217244-1-jacobraz@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Wed, 25 Sep 2019 13:59:15 +0000 (06:59 -0700)]
workqueue: Fix pwq ref leak in rescuer_thread()
commit
e66b39af00f426b3356b96433d620cb3367ba1ff upstream.
008847f66c3 ("workqueue: allow rescuer thread to do more work.") made
the rescuer worker requeue the pwq immediately if there may be more
work items which need rescuing instead of waiting for the next mayday
timer expiration. Unfortunately, it doesn't check whether the pwq is
already on the mayday list and unconditionally gets the ref and moves
it onto the list. This doesn't corrupt the list but creates an
additional reference to the pwq. It got queued twice but will only be
removed once.
This leak later can trigger pwq refcnt warning on workqueue
destruction and prevent freeing of the workqueue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Williams, Gerald S" <gerald.s.williams@intel.com>
Cc: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Thu, 19 Sep 2019 01:43:40 +0000 (18:43 -0700)]
workqueue: Fix spurious sanity check failures in destroy_workqueue()
commit
def98c84b6cdf2eeea19ec5736e90e316df5206b upstream.
Before actually destrying a workqueue, destroy_workqueue() checks
whether it's actually idle. If it isn't, it prints out a bunch of
warning messages and leaves the workqueue dangling. It unfortunately
has a couple issues.
* Mayday list queueing increments pwq's refcnts which gets detected as
busy and fails the sanity checks. However, because mayday list
queueing is asynchronous, this condition can happen without any
actual work items left in the workqueue.
* Sanity check failure leaves the sysfs interface behind too which can
lead to init failure of newer instances of the workqueue.
This patch fixes the above two by
* If a workqueue has a rescuer, disable and kill the rescuer before
sanity checks. Disabling and killing is guaranteed to flush the
existing mayday list.
* Remove sysfs interface before sanity checks.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marcin Pawlowski <mpawlowski@fb.com>
Reported-by: "Williams, Gerald S" <gerald.s.williams@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Fomichev [Wed, 6 Nov 2019 22:34:35 +0000 (14:34 -0800)]
dm zoned: reduce overhead of backing device checks
commit
e7fad909b68aa37470d9f2d2731b5bec355ee5d6 upstream.
Commit
75d66ffb48efb3 added backing device health checks and as a part
of these checks, check_events() block ops template call is invoked in
dm-zoned mapping path as well as in reclaim and flush path. Calling
check_events() with ATA or SCSI backing devices introduces a blocking
scsi_test_unit_ready() call being made in sd_check_events(). Even though
the overhead of calling scsi_test_unit_ready() is small for ATA zoned
devices, it is much larger for SCSI and it affects performance in a very
negative way.
Fix this performance regression by executing check_events() only in case
of any I/O errors. The function dmz_bdev_is_dying() is modified to call
only blk_queue_dying(), while calls to check_events() are made in a new
helper function, dmz_check_bdev().
Reported-by: zhangxiaoxu <zhangxiaoxu5@huawei.com>
Fixes:
75d66ffb48efb3 ("dm zoned: properly handle backing device failure")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maged Mokhtar [Wed, 23 Oct 2019 20:41:17 +0000 (22:41 +0200)]
dm writecache: handle REQ_FUA
commit
c1005322ff02110a4df7f0033368ea015062b583 upstream.
Call writecache_flush() on REQ_FUA in writecache_map().
Cc: stable@vger.kernel.org # 4.18+
Signed-off-by: Maged Mokhtar <mmokhtar@petasan.org>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sumit Garg [Mon, 14 Oct 2019 12:02:45 +0000 (17:32 +0530)]
hwrng: omap - Fix RNG wait loop timeout
commit
be867f987a4e1222114dd07a01838a17c26f3fff upstream.
Existing RNG data read timeout is 200us but it doesn't cover EIP76 RNG
data rate which takes approx. 700us to produce 16 bytes of output data
as per testing results. So configure the timeout as 1000us to also take
account of lack of udelay()'s reliability.
Fixes:
383212425c92 ("hwrng: omap - Add device variant for SafeXcel IP-76 found in Armada 8K")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amir Goldstein [Fri, 6 Dec 2019 06:33:36 +0000 (08:33 +0200)]
ovl: relax WARN_ON() on rename to self
commit
6889ee5a53b8d969aa542047f5ac8acdc0e79a91 upstream.
In ovl_rename(), if new upper is hardlinked to old upper underneath
overlayfs before upper dirs are locked, user will get an ESTALE error
and a WARN_ON will be printed.
Changes to underlying layers while overlayfs is mounted may result in
unexpected behavior, but it shouldn't crash the kernel and it shouldn't
trigger WARN_ON() either, so relax this WARN_ON().
Reported-by: syzbot+bb1836a212e69f8e201a@syzkaller.appspotmail.com
Fixes:
804032fabb3b ("ovl: don't check rename to self")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amir Goldstein [Sun, 17 Nov 2019 15:43:44 +0000 (17:43 +0200)]
ovl: fix corner case of non-unique st_dev;st_ino
commit
9c6d8f13e9da10a26ad7f0a020ef86e8ef142835 upstream.
On non-samefs overlay without xino, non pure upper inodes should use a
pseudo_dev assigned to each unique lower fs and pure upper inodes use the
real upper st_dev.
It is fine for an overlay pure upper inode to use the same st_dev;st_ino
values as the real upper inode, because the content of those two different
filesystem objects is always the same.
In this case, however:
- two filesystems, A and B
- upper layer is on A
- lower layer 1 is also on A
- lower layer 2 is on B
Non pure upper overlay inode, whose origin is in layer 1 will have the same
st_dev;st_ino values as the real lower inode. This may result with a false
positive results of 'diff' between the real lower and copied up overlay
inode.
Fix this by using the upper st_dev;st_ino values in this case. This breaks
the property of constant st_dev;st_ino across copy up of this case. This
breakage will be fixed by a later patch.
Fixes:
5148626b806a ("ovl: allocate anon bdev per unique lower fs")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 6 Dec 2019 15:26:00 +0000 (16:26 +0100)]
lib: raid6: fix awk build warnings
commit
702600eef73033ddd4eafcefcbb6560f3e3a90f7 upstream.
Newer versions of awk spit out these fun warnings:
awk: ../lib/raid6/unroll.awk:16: warning: regexp escape sequence `\#' is not a known regexp operator
As commit
700c1018b86d ("x86/insn: Fix awk regexp warnings") showed, it
turns out that there are a number of awk strings that do not need to be
escaped and newer versions of awk now warn about this.
Fix the string up so that no warning is produced. The exact same kernel
module gets created before and after this patch, showing that it wasn't
needed.
Link: https://lore.kernel.org/r/20191206152600.GA75093@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 11 Nov 2019 19:40:46 +0000 (13:40 -0600)]
rtlwifi: rtl8192de: Fix missing enable interrupt flag
commit
330bb7117101099c687e9c7f13d48068670b9c62 upstream.
In commit
38506ecefab9 ("rtlwifi: rtl_pci: Start modification for
new drivers"), the flag that indicates that interrupts are enabled was
never set.
In addition, there are several places when enable/disable interrupts
were commented out are restored. A sychronize_interrupts() call is
removed.
Fixes:
38506ecefab9 ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 11 Nov 2019 19:40:45 +0000 (13:40 -0600)]
rtlwifi: rtl8192de: Fix missing callback that tests for hw release of buffer
commit
3155db7613edea8fb943624062baf1e4f9cfbfd6 upstream.
In commit
38506ecefab9 ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback needed to check if the hardware has released
a buffer indicating that a DMA operation is completed was not added.
Fixes:
38506ecefab9 ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 11 Nov 2019 19:40:44 +0000 (13:40 -0600)]
rtlwifi: rtl8192de: Fix missing code to retrieve RX buffer address
commit
0e531cc575c4e9e3dd52ad287b49d3c2dc74c810 upstream.
In commit
38506ecefab9 ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback to get the RX buffer address was added to
the PCI driver. Unfortunately, driver rtl8192de was not modified
appropriately and the code runs into a WARN_ONCE() call. The use
of an incorrect array is also fixed.
Fixes:
38506ecefab9 ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josef Bacik [Fri, 15 Nov 2019 20:43:06 +0000 (15:43 -0500)]
btrfs: record all roots for rename exchange on a subvol
commit
3e1740993e43116b3bc71b0aad1e6872f6ccf341 upstream.
Testing with the new fsstress support for subvolumes uncovered a pretty
bad problem with rename exchange on subvolumes. We're modifying two
different subvolumes, but we only start the transaction on one of them,
so the other one is not added to the dirty root list. This is caught by
btrfs_cow_block() with a warning because the root has not been updated,
however if we do not modify this root again we'll end up pointing at an
invalid root because the root item is never updated.
Fix this by making sure we add the destination root to the trans list,
the same as we do with normal renames. This fixes the corruption.
Fixes:
cdd1fedf8261 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT")
CC: stable@vger.kernel.org # 4.9+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Wed, 30 Oct 2019 12:23:01 +0000 (12:23 +0000)]
Btrfs: send, skip backreference walking for extents with many references
commit
fd0ddbe2509568b00df364156f47561e9f469f15 upstream.
Backreference walking, which is used by send to figure if it can issue
clone operations instead of write operations, can be very slow and use
too much memory when extents have many references. This change simply
skips backreference walking when an extent has more than 64 references,
in which case we fallback to a write operation instead of a clone
operation. This limit is conservative and in practice I observed no
signicant slowdown with up to 100 references and still low memory usage
up to that limit.
This is a temporary workaround until there are speedups in the backref
walking code, and as such it does not attempt to add extra interfaces or
knobs to tweak the threshold.
Reported-by: Atemu <atemu.main@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CAE4GHgkvqVADtS4AzcQJxo0Q1jKQgKaW3JGp3SGdoinVo=C9eQ@mail.gmail.com/T/#me55dc0987f9cc2acaa54372ce0492c65782be3fa
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qu Wenruo [Thu, 24 Oct 2019 01:38:29 +0000 (09:38 +0800)]
btrfs: Remove btrfs_bio::flags member
commit
34b127aecd4fe8e6a3903e10f204a7b7ffddca22 upstream.
The last user of btrfs_bio::flags was removed in commit
326e1dbb5736
("block: remove management of bi_remaining when restoring original
bi_end_io"), remove it.
(Tagged for stable as the structure is heavily used and space savings
are desirable.)
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Thu, 3 Oct 2019 14:27:13 +0000 (07:27 -0700)]
btrfs: Avoid getting stuck during cyclic writebacks
commit
f7bddf1e27d18fbc7d3e3056ba449cfbe4e20b0a upstream.
During a cyclic writeback, extent_write_cache_pages() uses done_index
to update the writeback_index after the current run is over. However,
instead of current index + 1, it gets to to the current index itself.
Unfortunately, this, combined with returning on EOF instead of looping
back, can lead to the following pathlogical behavior.
1. There is a single file which has accumulated enough dirty pages to
trigger balance_dirty_pages() and the writer appending to the file
with a series of short writes.
2. balance_dirty_pages kicks in, wakes up background writeback and sleeps.
3. Writeback kicks in and the cursor is on the last page of the dirty
file. Writeback is started or skipped if already in progress. As
it's EOF, extent_write_cache_pages() returns and the cursor is set
to done_index which is pointing to the last page.
4. Writeback is done. Nothing happens till balance_dirty_pages
finishes, at which point we go back to #1.
This can almost completely stall out writing back of the file and keep
the system over dirty threshold for a long time which can mess up the
whole system. We encountered this issue in production with a package
handling application which can reliably reproduce the issue when
running under tight memory limits.
Reading the comment in the error handling section, this seems to be to
avoid accidentally skipping a page in case the write attempt on the
page doesn't succeed. However, this concern seems bogus.
On each page, the code either:
* Skips and moves onto the next page.
* Fails issue and sets done_index to index + 1.
* Successfully issues and continue to the next page if budget allows
and not EOF.
IOW, as long as it's not EOF and there's budget, the code never
retries writing back the same page. Only when a page happens to be
the last page of a particular run, we end up retrying the page, which
can't possibly guarantee anything data integrity related. Besides,
cyclic writes are only used for non-syncing writebacks meaning that
there's no data integrity implication to begin with.
Fix it by always setting done_index past the current page being
processed.
Note that this problem exists in other writepages too.
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Fri, 11 Oct 2019 15:41:20 +0000 (16:41 +0100)]
Btrfs: fix negative subv_writers counter and data space leak after buffered write
commit
a0e248bb502d5165b3314ac3819e888fdcdf7d9f upstream.
When doing a buffered write it's possible to leave the subv_writers
counter of the root, used for synchronization between buffered nocow
writers and snapshotting. This happens in an exceptional case like the
following:
1) We fail to allocate data space for the write, since there's not
enough available data space nor enough unallocated space for allocating
a new data block group;
2) Because of that failure, we try to go to NOCOW mode, which succeeds
and therefore we set the local variable 'only_release_metadata' to true
and set the root's sub_writers counter to 1 through the call to
btrfs_start_write_no_snapshotting() made by check_can_nocow();
3) The call to btrfs_copy_from_user() returns zero, which is very unlikely
to happen but not impossible;
4) No pages are copied because btrfs_copy_from_user() returned zero;
5) We call btrfs_end_write_no_snapshotting() which decrements the root's
subv_writers counter to 0;
6) We don't set 'only_release_metadata' back to 'false' because we do
it only if 'copied', the value returned by btrfs_copy_from_user(), is
greater than zero;
7) On the next iteration of the while loop, which processes the same
page range, we are now able to allocate data space for the write (we
got enough data space released in the meanwhile);
8) After this if we fail at btrfs_delalloc_reserve_metadata(), because
now there isn't enough free metadata space, or in some other place
further below (prepare_pages(), lock_and_cleanup_extent_if_need(),
btrfs_dirty_pages()), we break out of the while loop with
'only_release_metadata' having a value of 'true';
9) Because 'only_release_metadata' is 'true' we end up decrementing the
root's subv_writers counter to -1 (through a call to
btrfs_end_write_no_snapshotting()), and we also end up not releasing the
data space previously reserved through btrfs_check_data_free_space().
As a consequence the mechanism for synchronizing NOCOW buffered writes
with snapshotting gets broken.
Fix this by always setting 'only_release_metadata' to false at the start
of each iteration.
Fixes:
8257b2dc3c1a ("Btrfs: introduce btrfs_{start, end}_nocow_write() for each subvolume")
Fixes:
7ee9e4405f26 ("Btrfs: check if we can nocow if we don't have data space")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Wed, 9 Oct 2019 16:43:59 +0000 (17:43 +0100)]
Btrfs: fix metadata space leak on fixup worker failure to set range as delalloc
commit
536870071dbc4278264f59c9a2f5f447e584d139 upstream.
In the fixup worker, if we fail to mark the range as delalloc in the io
tree, we must release the previously reserved metadata, as well as update
the outstanding extents counter for the inode, otherwise we leak metadata
space.
In pratice we can't return an error from btrfs_set_extent_delalloc(),
which is just a wrapper around __set_extent_bit(), as for most errors
__set_extent_bit() does a BUG_ON() (or panics which hits a BUG_ON() as
well) and returning an -EEXIST error doesn't happen in this case since
the exclusive bits parameter always has a value of 0 through this code
path. Nevertheless, just fix the error handling in the fixup worker,
in case one day __set_extent_bit() can return an error to this code
path.
Fixes:
f3038ee3a3f101 ("btrfs: Handle btrfs_set_extent_delalloc failure in fixup worker")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josef Bacik [Thu, 26 Sep 2019 12:29:32 +0000 (08:29 -0400)]
btrfs: use refcount_inc_not_zero in kill_all_nodes
commit
baf320b9d531f1cfbf64c60dd155ff80a58b3796 upstream.
We hit the following warning while running down a different problem
[ 6197.175850] ------------[ cut here ]------------
[ 6197.185082] refcount_t: underflow; use-after-free.
[ 6197.194704] WARNING: CPU: 47 PID: 966 at lib/refcount.c:190 refcount_sub_and_test_checked+0x53/0x60
[ 6197.521792] Call Trace:
[ 6197.526687] __btrfs_release_delayed_node+0x76/0x1c0
[ 6197.536615] btrfs_kill_all_delayed_nodes+0xec/0x130
[ 6197.546532] ? __btrfs_btree_balance_dirty+0x60/0x60
[ 6197.556482] btrfs_clean_one_deleted_snapshot+0x71/0xd0
[ 6197.566910] cleaner_kthread+0xfa/0x120
[ 6197.574573] kthread+0x111/0x130
[ 6197.581022] ? kthread_create_on_node+0x60/0x60
[ 6197.590086] ret_from_fork+0x1f/0x30
[ 6197.597228] ---[ end trace
424bb7ae00509f56 ]---
This is because the free side drops the ref without the lock, and then
takes the lock if our refcount is 0. So you can have nodes on the tree
that have a refcount of 0. Fix this by zero'ing out that element in our
temporary array so we don't try to kill it again.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>