OSDN Git Service
Francisco Jerez [Fri, 29 May 2015 13:44:13 +0000 (16:44 +0300)]
drm/i915: Fix command parser to validate multiple register access with the same command.
Until now the software command checker assumed that commands could
read or write at most a single register per packet. This is not
necessarily the case, MI_LOAD_REGISTER_IMM expects a variable-length
list of offset/value pairs and writes them in sequence. The previous
code would only check whether the first entry was valid, effectively
allowing userspace to write unrestricted registers of the MMIO space
by sending a multi-register write with a legal first register, with
potential security implications on Gen6 and 7 hardware.
Fix it by extending the drm_i915_cmd_descriptor table to represent
multi-register access and making validate_cmd() iterate for all
register offsets present in the command packet.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Thu, 28 May 2015 15:32:36 +0000 (18:32 +0300)]
drm/i915: Don't skip request retirement if the active list is empty
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rodrigo Vivi [Wed, 3 Jun 2015 23:50:19 +0000 (16:50 -0700)]
drm/i915/skl: Fix DMC API version in firmware file name
04 is the minor version. API version is ver1.
So let's follow same scheme used on published version at 01.org.
If really needed the minor version a follow-up updated will be
done. But for now we need to move fwd and unblock end users.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Michel Thierry [Fri, 29 May 2015 13:15:05 +0000 (14:15 +0100)]
drm/i915: limit PPGTT size to 2GB in 32-bit platforms
We already set this limit for the GGTT.
This is a temporary patch until a full replacement of size_t variables
(inadequate in 32-bit kernel) is in place.
Regression from:
commit
a4e0bedca678c81eea4cd79a4bd502335639f73a
Author: Michel Thierry <michel.thierry@intel.com>
Date: Wed Apr 8 12:13:35 2015 +0100
drm/i915: Use complete address space in true PPGTT
v2: Prettify code and explain why this is needed. (Chris)
v3: Don't hide the compilation warning in 32-bit. (Chris)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Thu, 28 May 2015 17:26:58 +0000 (10:26 -0700)]
drm/i915: Another fbdev hack to avoid PSR on fbcon.
With unified modeset and flip paths introduced recently when switching
to fbcon PSR was being disabled on fb_set_par path but re-enabled on
fb_pan_display one, causing missed screen updates and un unusable
console.
Regression introduced with:
commit
bb54662350662815b4bfc2ff4464330a2dbd7041
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:13 2015 +0300
drm/i915: Unify modeset and flip paths of intel_crtc_set_config()
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rodrigo Vivi [Thu, 28 May 2015 17:21:16 +0000 (10:21 -0700)]
drm/i915: Return the frontbuffer flip to enable intel_crtc_enable_planes.
Without this frontbuffer flip when enabling planes PSR got compromised
and wasn't being enabled waiting forever on the flush that never
arrived.
Another solution would to create a enable_cursor function and split this
frontbuffer flip among the different plane enable and disable functions.
But if necessary this can be done in a follow up work. For now let's
just fix the regression.
It was removed by:
commit
87d4300a7dbc19634018e147b4753f3c9bb5f471
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:54 2015 +0300
drm/i915: Move intel_(pre_disable/post_enable)_primary to intel_display.c, and use it there.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 25 May 2015 21:52:29 +0000 (18:52 -0300)]
drm/i915: disable IPS while getting the sink CRCs
This commit is the "sink CRC" version of:
commit
8c740dcea254a1472df2c0ac5ac585412a2507ec
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Oct 17 18:42:03 2014 -0300
drm/i915: disable IPS while getting the pipe CRCs.
For some unknown reason, when IPS gets enabled, the sink CRC changes.
Since hsw_enable_ips() doesn't really guarantee to enable IPS (it
depends on package C-states), we can't really predict if IPS is
enabled or disabled while running our CRC tests, so let's just
completely disable IPS while sink CRCs are being used.
If we find a way to make IPS not change the pipe CRC result, we may
want to fix IPS and then revert this patch (and
8c740dcea too). While
this doesn't happen, let's merge this patch, so the IGT tests relying
on sink CRCs can work properly.
This was discovered while developing a new IGT test, which will
probably be called kms_frontbuffer_tracking.
Testcase: igt/kms_frontbuffer_tracking (not on upstream IGT yet)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 28 May 2015 07:38:45 +0000 (09:38 +0200)]
drm/i915: Disable 12bpc hdmi for now
It's totally broken, and since
commit
d328c9d78d64ca11e744fe227096990430a88477
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
the kernel will try to use it even for the common rgb888 framebuffers.
Ville has patches to fix it all up properly, but unfortunately they're
stuck in review limbo. And since the 4.2 feature cutoff has passed we
need to somehow handle this regression.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Ville Syrjälä [Tue, 26 May 2015 17:42:31 +0000 (20:42 +0300)]
drm/i915: Adjust sideband locking a bit for CHV/VLV
chv_enable_pll() doesn't need to hold sb_lock for the entire duration of
the function. Drop the lock as soon as possible.
valleyview_set_cdclk() does a potential lock+unlock+lock+unlock cycle
with sb_lock. Grab the lock a few lines earlier so we can make do
with a single lock+unlock cycle always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 26 May 2015 17:42:30 +0000 (20:42 +0300)]
drm/i915: s/dpio_lock/sb_lock/
Rename dpio_lock to sb_lock to inform the reader that its primary
purpose is to protect the sideband mailbox rather than some DPIO
state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 26 May 2015 17:27:23 +0000 (20:27 +0300)]
drm/i915: Kill intel_flush_primary_plane()
The primary plane frobbing was removed from the sprite code in
commit
ecce87ea3ab55ad0dc64460e6422c357d158a55e
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:50 2015 +0300
drm/i915: Remove implicitly disabling primary plane for now
but the intel_flush_primary_plane() calls were left behind. Replace them
with straight forward POSTING_READ() of the sprite surface address
register.
The other user of intel_flush_primary_plane() is g4x_disable_trickle_feed()
where we can just inline the steps directly.
This allows intel_flush_primary_plane() to be killed off.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 26 May 2015 17:22:39 +0000 (20:22 +0300)]
drm/i915: Throw out WIP CHV power well definitions
Expecting CHV power wells to be just an extended versions of the VLV
power wells, a bunch of commented out power wells were added in
anticipation when Punit folks would implement it all. Turns out they
never did, and instead CHV has fewer power wells than VLV. Rip out all
the #if 0'ed junk that's not needed.
v2: Rename the "pipe-a" well to "display" to match VLV
Clarify the pipe A power well relationship to pipes B and C (Deepak)
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 26 May 2015 17:22:38 +0000 (20:22 +0300)]
drm/i915: Use the default 600ns LDO programming sequence delay
Not sure which LDO programming sequence delay should be used for the CHV
PHY, but the spec says that 600ns is "Used by default for initial
bringup", and the BIOS seems to use that, so let's do the same.
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Michel Thierry [Mon, 27 Apr 2015 11:31:44 +0000 (12:31 +0100)]
drm/i915: Remove unnecessary null check in execlists_context_unqueue
commit
53292cdb066950611e5bc2e0eb109c7edb42af78 ("drm/i915: Workaround
to avoid lite restore with HEAD==TAIL") added a check for req0 != null
which is unnecessary.
The only way req0 could be null is if the list was empty, and this is
already addressed at the beginning of execlists_context_unqueue().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Thu, 21 May 2015 20:01:47 +0000 (21:01 +0100)]
drm/i915: Use spinlocks for checking when to waitboost
In commit
1854d5ca0dd7a9fc11243ff220a3e93fce2b4d3e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:32 2015 +0100
drm/i915: Deminish contribution of wait-boosting from clients
we removed an atomic timer based check for allowing waitboosting and
moved it below the mutex taken during RPS. However, that mutex can be
held for long periods of time on Vallyview/Cherryview as communication
with the PCU is slow. As clients may frequently wait for results (e.g.
such as tranform feedback) we introduced contention between the client
and the RPS worker. We can take advantage of the RPS worker, by
switching the wait boost decision to use spin locks and defer the
actual reclocking to the worker.
Fixes a regression of up to 45% on Baytrail and Baswell!
v2 (Daniel):
- Use max_freq_softlimit instead of the not-yet-merged boost
frequency.
- Don't inject a fake irq into the boost work, instead treat
client_boost as just another legit waker.
v3: Drop the now unused mask (Chris).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90112
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 26 May 2015 13:57:19 +0000 (14:57 +0100)]
drm/i915: Fix the confusing comment about the ioctl limits
It was reported that this comment was confusing, and indeed it is.
v2: (one year later!) Add the range for the DRM_I915_* iotcl defines
(Daniel)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 26 May 2015 05:46:21 +0000 (07:46 +0200)]
Revert "drm/i915: Force clean compilation with -Werror"
This reverts commit
118182e9d7d5afa0c7c10f568afb46ab78b462e9.
It's causing too much trouble when compile-testing for non-i915 folks.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Daniel Vetter [Fri, 22 May 2015 17:45:27 +0000 (19:45 +0200)]
drm/i915: Update DRIVER_DATE to
20150522
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Thu, 21 May 2015 20:01:48 +0000 (21:01 +0100)]
drm/i915: Introduce DRM_I915_THROTTLE_JIFFIES
As Daniel commented on
commit
b7ffe1362c5f468b853223acc9268804aa92afc8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 27 13:41:24 2015 +0100
drm/i915: Free RPS boosts for all laggards
it is better to be explicit when sharing hardcoded values such as
throttle/boost timeouts. Make it so!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Thu, 21 May 2015 20:01:45 +0000 (21:01 +0100)]
drm/i915: Use the correct destructor for freeing requests on error
After allocating from the slab cache, we then need to free the request
back into the slab cache upon error (and not call kfree as that leads
to eventual memory corruption).
Fixes regression from
commit
efab6d8dd158fdccbe6a030f89fbf9ca0a9564e4
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:57 2015 +0100
drm/i915: Use a separate slab for requests
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chandra Konduru [Mon, 18 May 2015 23:18:44 +0000 (16:18 -0700)]
drm/i915/skl: don't fail colorkey + scaler request
There is a mplayer video failure reported with xv.
This is because there is a request to do both plane scaling
and colorkey. Because skl hw doesn't support plane scaling
and colorkey at the same time, request is failed which is expected
behavior.
To make xv operate, this patch allows colorkey continue to work
without using scaler. Then behavior would be similar to platforms
without plane scaler support.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90449
[danvet: change can_scale to bool as requested by Ville.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 19 May 2015 17:32:57 +0000 (20:32 +0300)]
drm/i915: Enable GTT caching on gen8
GTT caching was disabled by default on gen8 due to not working with
big pages. Some information suggests that it got fixed, but still
GTT caching has been left disabled by default. Or could be it just
meant that the default was changed to off, and hence the problem
got solved.
Enable GTT caching in the hopes of some performance increase.
Whether or not the big pages issue has been fixed is irrelevant
at this stage since we don't use big pages.
This gives me a 1-2% improvement in xonotic on my BSW. Haven't tried
BDW, but supposedly it has larger TLBs so might not benefit as much.
On HSW GTT caching is enabled by default.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 19 May 2015 17:32:56 +0000 (20:32 +0300)]
drm/i915: Move WaProgramL3SqcReg1Default:bdw to init_clock_gating()
GEN8_L3SQCREG1 isn't saved in the context (verified by going through
a context dump), and so we shouldn't be using the ring w/a code to
initialize it. Also Bspec explicitly talks about MMIO and writing it
with the CPU.
Additionally there's another w/a WaTempDisableDOPClkGating:bdw which
tells us to disable DOP clock gating around the GEN8_L3SQCREG1 write
to make sure everyone notices the change. So let's do that as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 19 May 2015 17:32:55 +0000 (20:32 +0300)]
drm/i915: Use ilk_init_lp_watermarks() on BDW
We're not using ilk_init_lp_watermarks() on BDW for some reason.
Probably due to the BDW patches and the relevant WM patches landing
roughlly at the same time. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:38 +0000 (17:17 +0300)]
drm/i915: Disable FDI RX/TX before the ports
Bspec says we should disable the FDI RX/TX before disabling the PCH
ports. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:37 +0000 (17:17 +0300)]
drm/i915: Disable CRT port after pipe on PCH platforms
Follow the BSpec sequence for the CRT port as well on PCH platforms,
ie. disable the pipe before the port.
Didn't bother looking at DDI in detail yet, so leave that one be even
though the CRT is a PCH port there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:36 +0000 (17:17 +0300)]
drm/i915: Disable SDVO port after the pipe on PCH platforms
While at it also remove the redundant/unneeded w/a like done for hdmi
already.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Mention that this also removes the unneeded w/a, as suggested
by Jesse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:35 +0000 (17:17 +0300)]
drm/i915: Disable HDMI port after the pipe on PCH platforms
BSpec says we should disable all ports after the pipe on PCH
platforms. Do so. Fixes a pipe off timeout on ILK now caused by
the transcoder B workaround.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:34 +0000 (17:17 +0300)]
drm/i915: Fix the IBX transcoder B workarounds
Currently the IBX transcoder B workarounds are not working correctly.
Well, the HDMI one seems to be working somewhat, but the DP one is
definitely busted.
After a bit of experimentation it looks like the best way to make this
work is first disable the port on transcoder B, and then re-enable it
transcoder A, and immediately disable it again.
We can also clean up the code by noting that we can't be called without
a valid crtc. And also note that port A on ILK does not need the
workaround, so let's check for that one too.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:33 +0000 (17:17 +0300)]
drm/i915: Write the SDVO reg twice on IBX
On IBX the SDVO/HDMI register write may be masked when enabling the
port, so it may need to written twice. The HDMI code does this, but
the SDVO code does not. Add the workaround to the SDVO code as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:31 +0000 (17:17 +0300)]
drm/i915: Fix DP enhanced framing for CPT
Currently we're always enabling enhanced framing on CPT even if the sink
doesn't support it. Fix this up by actaully looking at what the sink
tells us.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:30 +0000 (17:17 +0300)]
drm/i915: Clean up the CPT DP .get_hw_state() port readout
Define a TRANS_DP_PIPE_TO_PORT() to make the CPT DP .get_hw_state()
pipe readout neater.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:29 +0000 (17:17 +0300)]
drm/i915: Clarfify the DP code platform checks
intel_dp.c is a mess with all the checks for different
platform/PCH variants and ports. Try to clean it up by recognizing
the following facts:
- IVB port A, and CPT port B/C/D are always the special cases
- VLV/CHV don't have port A
- Using the same kind of logic everywhere makes things much easier to
parse
So let's move the IVB port A and PCH port B/C/D checks to be done first,
and let the other cases fall through, and always check for these things
using the same logic.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:28 +0000 (17:17 +0300)]
drm/i915: Remove the double register write from intel_disable_hdmi()
IBX can have problems with the first write to the port register getting
masked when enabling the port. We are trying to apply the workaround
also when disabling the port where it's not needed, and we also try
to apply it for CPT/PPT as well which don't need it. Just kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with the remove CHV if block.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 5 May 2015 14:17:27 +0000 (17:17 +0300)]
drm/i915: Remove a bogus 12bpc "toggle" from intel_disable_hdmi()
The IBX 12bpc port enable toggle is only relevant when enabling
the port, not when disabling it. Also this code doesn't actually
toggle anything, and essentially just writes the port register
one extra time. Furthermore CPT/PPT don't need such workarounds
and yet we include them. Just kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Thu, 21 May 2015 15:37:48 +0000 (16:37 +0100)]
drm/i915/skl: Deinit/init the display at suspend/resume
We need to re-init the display hardware when going out of suspend. This
includes:
- Hooking the PCH to the reset logic
- Restoring CDCDLK
- Enabling the DDB power
Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:
- DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
of supported frequencies. As eDP also uses DPLL0 for its link rate,
once DPLL0 is on, we restrict the possible eDP link rates the chosen
VCO.
- CDCLK also limits the bandwidth available to push pixels.
So, as a first step, this commit restore what the BIOS set, until I can
do more testing.
In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:
#include <stdio.h>
#include <stdint.h>
#include <assert.h>
#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))
static const struct dpll_freq {
unsigned int freq;
unsigned int decimal;
} freqs[] = {
{ .freq = 308570, .decimal =
0b01001100111},
{ .freq = 337500, .decimal =
0b01010100001},
{ .freq = 432000, .decimal =
0b01101011110},
{ .freq = 450000, .decimal =
0b01110000010},
{ .freq = 540000, .decimal =
0b10000110110},
{ .freq = 617140, .decimal =
0b10011010000},
{ .freq = 675000, .decimal =
0b10101000100},
};
static void intbits(unsigned int v)
{
int i;
for(i = 10; i >= 0; i--)
putchar('0' + ((v >> i) & 1));
}
static unsigned int freq_decimal(unsigned int freq /* in kHz */)
{
return (freq - 1000) / 500;
}
static void test_freq(const struct dpll_freq *entry)
{
unsigned int decimal = freq_decimal(entry->freq);
printf("freq: %d, expected: ", entry->freq);
intbits(entry->decimal);
printf(", got: ");
intbits(decimal);
putchar('\n');
assert(decimal == entry->decimal);
}
int main(int argc, char **argv)
{
int i;
for (i = 0; i < ARRAY_SIZE(freqs); i++)
test_freq(&freqs[i]);
return 0;
}
v2:
- Rebase on top of -nightly
- Use (freq - 1000) / 500 for the decimal frequency (Ville)
- Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
- Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
be consistent with the BXT code (Ville)
- Store boot CDCLK in ddi_pll_init (Ville)
- Merge dev_priv's skl_boot_cdclk into cdclk_freq
- Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
- Replace various '0' by SKL_DPLL0 to be a bit more explicit that
we're programming DPLL0
- Busy poll the PCU before doing the frequency change. It takes about
3/4 cycles, each separated by 10us, to get the ACK from the CPU
(Ville)
v3:
- Restore dev_priv->skl_boot_cdclk, leaving unification with
dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:24 +0000 (13:41 +0100)]
drm/i915: Free RPS boosts for all laggards
If the client stalls on a congested request, chosen to be 20ms old to
match throttling, allow the client a free RPS boost.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
[danvet: s/0/NULL/ reported by 0-day build]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:23 +0000 (13:41 +0100)]
drm/i915: Don't downclock whilst we have clients waiting for GPU results
If we have clients stalled waiting for requests, ignore the GPU if it
signals that it should downclock due to low load. This helps prevent
the automatic timeout from causing extremely long running batches from
taking even longer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:22 +0000 (13:41 +0100)]
drm/i915: Convert RPS tracking to a intel_rps_client struct
Now that we have internal clients, rather than faking a whole
drm_i915_file_private just for tracking RPS boosts, create a new struct
intel_rps_client and pass it along when waiting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:21 +0000 (13:41 +0100)]
drm/i915: Limit mmio flip RPS boosts
Since we will often pageflip to an active surface, we will often have to
wait for the surface to be written before issuing the flip. Also we are
likely to wait on that surface in plenty of time before the vblank.
Since we have a mechanism for boosting when a flip misses the expected
vblank, curtain the number of times we RPS boost when simply waiting for
mmioflip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:20 +0000 (13:41 +0100)]
drm/i915: Limit ring synchronisation (sw sempahores) RPS boosts
Ring switches can occur many times per frame, and are often out of
control, causing frequent RPS boosting for no practical benefit. Treat
the sw semaphore synchronisation as a separate client and only allow it
to boost once per busy/idle cycle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:18 +0000 (13:41 +0100)]
drm/i915: Inline check required for object syncing prior to execbuf
This trims a little overhead from the common case of not needing to
synchronize between rings.
v2: execlists is special and likes to duplicate code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:17 +0000 (13:41 +0100)]
drm/i915: Implement inter-engine read-read optimisations
Currently, we only track the last request globally across all engines.
This prevents us from issuing concurrent read requests on e.g. the RCS
and BCS engines (or more likely the render and media engines). Without
semaphores, we incur costly stalls as we synchronise between rings -
greatly impacting the current performance of Broadwell versus Haswell in
certain workloads (like video decode). With the introduction of
reference counted requests, it is much easier to track the last request
per ring, as well as the last global write request so that we can
optimise inter-engine read read requests (as well as better optimise
certain CPU waits).
v2: Fix inverted readonly condition for nonblocking waits.
v3: Handle non-continguous engine array after waits
v4: Rebase, tidy, rewrite ring list debugging
v5: Use obj->active as a bitfield, it looks cool
v6: Micro-optimise, mostly involving moving code around
v7: Fix retire-requests-upto for execlists (and multiple rq->ringbuf)
v8: Rebase
v9: Refactor i915_gem_object_sync() to allow the compiler to better
optimise it.
Benchmark: igt/gem_read_read_speed
hsw:gt3e (with semaphores):
Before: Time to read-read 1024k: 275.794µs
After: Time to read-read 1024k: 123.260µs
hsw:gt3e (w/o semaphores):
Before: Time to read-read 1024k: 230.433µs
After: Time to read-read 1024k: 124.593µs
bdw-u (w/o semaphores): Before After
Time to read-read 1x1: 26.274µs 10.350µs
Time to read-read 128x128: 40.097µs 21.366µs
Time to read-read 256x256: 77.087µs 42.608µs
Time to read-read 512x512: 281.999µs 181.155µs
Time to read-read 1024x1024: 1196.141µs 1118.223µs
Time to read-read 2048x2048: 5639.072µs 5225.837µs
Time to read-read 4096x4096: 22401.662µs 21137.067µs
Time to read-read 8192x8192: 89617.735µs 85637.681µs
Testcase: igt/gem_concurrent_blit (read-read and friends)
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v8]
[danvet: s/\<rq\>/req/g]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Thu, 21 May 2015 12:21:25 +0000 (14:21 +0200)]
drm/i915: s/\<rq\>/req/g
The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.
Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Imre Deak [Tue, 19 May 2015 14:05:42 +0000 (17:05 +0300)]
drm/i915/skl: enable WaForceContextSaveRestoreNonCoherent
v2:
- set the override disable flag too on stepping F0 (mika)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Tue, 19 May 2015 14:05:41 +0000 (17:05 +0300)]
drm/i915/bxt: fix WaForceContextSaveRestoreNonCoherent on steppings B0+
On B0 and C0 steppings the workaround enable bit would be overriden by
default, so the overriding must be disabled.
The WA was added in
commit
83a24979c40ebbf0fa0cd14df16f74142f373cd3
Author: Nick Hoath <nicholas.hoath@intel.com>
Date: Fri Apr 10 13:12:26 2015 +0100
drm/i915/bxt: Add WaForceContextSaveRestoreNonCoherent
Spotted-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 20 May 2015 13:12:47 +0000 (14:12 +0100)]
drm/i915: Force clean compilation with -Werror
Our driver compiles clean (nowadays thanks to 0day) but for me, at least,
it would be beneficial if the compiler threw an error rather than a
warning when it found a piece of suspect code. (I use this to
compile-check patch series and want to break on the first compiler error
in order to fix the patch.)
v2: Kick off a new "Debugging" submenu for i915.ko
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add "DRM i915" to the menu name as requested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 20 May 2015 13:45:16 +0000 (14:45 +0100)]
drm/i915: Kill the dev variable in intel_suspend_complete()
The macros we use there are the magic ones that can take either dev or
dev_priv. We'd like to move as much as possible towards dev_priv though.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 20 May 2015 13:45:15 +0000 (14:45 +0100)]
drm/i915: Add a space after ', ' and don't capitalize mid-sentence
Couldn't let it go!
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 20 May 2015 13:45:14 +0000 (14:45 +0100)]
drm/i915/bxt: Also add bxt_resume_prepare() to the S3/S4 path
Currently bxt_resume_prepare() is only used in the runtime-resume path.
Add it to the full S3/S4 path as well.
v2: Rebase on top of the vlv_resume_prepare() shuffling around
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sonika Jindal [Wed, 20 May 2015 08:10:48 +0000 (13:40 +0530)]
drm/i915/skl: Swapping 90 and 270 to be compliant with Xrandr
Since DRM_ROTATE is counter clockwise (which is compliant with Xrandr),
and HW rotation is clockwise, swapping 90/270 to work as expected from
userspace.
v2: Rebased
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Wed, 20 May 2015 06:03:27 +0000 (09:03 +0300)]
drm/i915: Update comment in clear_intel_crtc_state()
Explain why a few fields of the new pipe_config have their values
preserved, while the others are zeroed.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Tue, 19 May 2015 12:05:00 +0000 (15:05 +0300)]
drm/i915/skl: add F0 stepping ID
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Imre Deak [Tue, 19 May 2015 12:04:59 +0000 (15:04 +0300)]
drm/i915/bxt: limit WaDisableMaskBasedCammingInRCC to stepping A
Also make the WA comment consistent with the rest, where the stepping
info is not shown.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 19 May 2015 11:29:16 +0000 (12:29 +0100)]
drm/i915: Tighten the exposure ARGB/ABGR 8888 formats
ARGB8888 is used for cursors on all platforms so we need to allow it
everywhere.
ABGR8888 is currently only honoured:
- on VLV/CHV in sprite planes
- on SKL+ for primary and sprite planes
so only allow it for those platforms.
Note that we only support ARGB8888/ABGR8888 on the primary plane for
SKL/BXT because we have in line of sight the pipe bottom color on those
platforms and because the primary plane programming on VLV/CHV doesn't
anything different for those formats today.
v2: Fix the logic to forbid the creation ABGR2101010 fbs (Ville)
v3: Still allow the creation of ARGB8888 fbs now that cursor planes use
real fb objects (found by PRTS).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Mon, 18 May 2015 18:53:48 +0000 (19:53 +0100)]
drm/i915: Fix 'suspedn' typo
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Vandana Kannan [Wed, 13 May 2015 06:50:35 +0000 (12:20 +0530)]
drm/i915/bxt: Move around lane stagger calculation
Making lane stagger calculation common for HDMI and DP
v2: Imre's comments addressed
- Remove lane stagger from bxt_clk_div and make it a local variable in
ddi_pll_select
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Vandana Kannan [Wed, 13 May 2015 06:48:52 +0000 (12:18 +0530)]
drm/i915/bxt: Port PLL programming BUN
BUN 1: prop_coeff, int_coeff, tdctargetcnt programming updated and tied to
VCO frequencies. Program i_lockthresh in PORT_PLL_9.
VCO calculated based on the formula:
Desired Output = Port bit rate in MHz (DisplayPort HBR2 is 5400 MHz)
Fast Clock = Desired Output / 2
VCO = Fast Clock * P1 * P2
Prop_coeff, int_coeff, and tdctargetcnt modified according to above
calculation.
BUN 2: Port PLLs require additional programming at certain frequencies -
DCO amplitude in PORT_PLL_10
Review comments from Siva which were addressed in the initial version of the
patch.
- Change PORT_PLL_LOCK_THRESHOLD to PORT_PLL_LOCK_THRESHOLD_MASK
- Calculate for HDMI
- Correct values for vco = 5.4
- return in case of invalid vco range
v2: Imre's review comments addressed
- change dcoampovr_en to dcoampovr_en_h
- change PORT_PLL_DCO_AMP_OVR_EN to PORT_PLL_DCO_AMP_OVR_EN_H
- Correct lane stagger value for 324MHz
- Make coef common for HDMI and DP
- remove superfluous comments
v3: Imre's comments addressed
- Remove Prop_coeff, int_coeff, tdctargetcnt, dcoampovr_en, gain_ctl,
dcoampovr_en_h from bxt_clk_div and make them local variables.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> [v1]
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 18 May 2015 14:10:01 +0000 (17:10 +0300)]
drm/i915: add HAS_DP_MST feature test macro
Be in line with other features that we have.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 18 May 2015 13:01:45 +0000 (16:01 +0300)]
drm/i915/dp: make link rate printing prettier
Turn
[drm:intel_dp_print_rates] source rates: 162000,270000,540000,
[drm:intel_dp_print_rates] sink rates: 162000,270000,
[drm:intel_dp_print_rates] common rates: 162000,270000,
into
[drm:intel_dp_print_rates] source rates: 162000, 270000, 540000
[drm:intel_dp_print_rates] sink rates: 162000, 270000
[drm:intel_dp_print_rates] common rates: 162000, 270000
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 15 May 2015 18:43:56 +0000 (19:43 +0100)]
drm/i915/bxt: Update the Broxton PCI ids
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 15 May 2015 18:06:03 +0000 (19:06 +0100)]
drm/i915: Don't expose ARGB1555 on gen2/3
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 15 May 2015 18:06:01 +0000 (19:06 +0100)]
drm/i915: Remove ARBG/ABGR
2101010 on platform not supporting those formats
We just have have VLV and CHV sprites programming the hardware
differently for the ABGR2101010 so keep them working.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 15 May 2015 18:06:00 +0000 (19:06 +0100)]
drm/i915: Remove the COMMON_PRIMARY_FORMATS defines
That define makes it hard to figure out what is the actual list of
formats at a glance. Expand it then.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 15 May 2015 10:42:21 +0000 (11:42 +0100)]
drm/i915: Use uninterruptible mutex_lock for userptr bo creation
Mika encountered one pathological scenario under X where acquiring all
the mm locks (required to insert a mmu notifier) was very slow, so slow
that by the time we tried to lock the struct_mutex with the usual call
to i915_mutex_lock_interruptible(), X's signal timer had fired causing
us to restart the ioctl (and so looped indefinitely).
While I suspect this is the result of another bug (something leaking mm
perhaps?) we can forgo the error checking and interuptible nature of the
lock here so we only have to pay the expense once and get on with it.
This does expose the userptr creation routine to a driver livelock
though by not being interruptible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Init ret to avoid issues reported by PRTS.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Fri, 15 May 2015 08:51:50 +0000 (11:51 +0300)]
drm/i915: Preserve ddi_pll_sel when allocating new pipe_config
When the modeset code is reached with a CRTC that only needs a flip, the
code that assigns PLLs is skipped. But since there is still a state swap
for that CRTC, the current PLL assignment needs to be preserved. I
missed the ddi_pll_sel field in the following commit, which causes
warnings in DDI platforms.
commit
4978cc93d9ac240b435ce60431aef24239b4c270
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:21 2015 +0300
drm/i915: Preserve shared DPLL information in new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90410
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tvrtko Ursulin [Thu, 14 May 2015 12:38:31 +0000 (13:38 +0100)]
drm/i915: Dump some DPLL fields in pipe config debug
v2: Split strings to 80 char, add ddi_pll_sel and fixed typo. (Damien Lespiau)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Fri, 15 May 2015 10:34:29 +0000 (13:34 +0300)]
drm/i915: Don't overwrite (e)DP PLL selection on SKL
In the following commit, the place where the contents of dpll_hw_state
in crtc_state where zeroed was changed. Prior to that commit, it
happened when the new state was allocated, but now that happens just
before the call the .crtc_compute_clock() hook. The DP code for SKL,
however, sets up the (private) PLL in the encoder compute config
function that has already run by the time that memset() is reached,
causing the previous value to be lost.
This patch fixes the issue by moving the memset() down the call chain,
so that it is only called if the values in dpll_hw_state are going to be
updated.
commit
4978cc93d9ac240b435ce60431aef24239b4c270
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:21 2015 +0300
drm/i915: Preserve shared DPLL information in new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90462
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reported-and-tested-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 13 May 2015 12:34:05 +0000 (15:34 +0300)]
drm/i915/bios: be more explicit about discarding iomem address space
Add one explicit discard of __iomem address space qualifier in
validate_vbt(), and respect it otherwise. This adds clarity in the code,
and reduces the sparse warnings from the module to just one.
Quoting Daniel, "The vbt really is plain old memory. Except that it's
reserved in the e820 table as something special and hence treated as io
range by the kernel. But it is memory, hence casting away the __iomem is
imo the right approach."
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tvrtko Ursulin [Wed, 13 May 2015 15:51:08 +0000 (16:51 +0100)]
drm/i915: Output scaler related pipe config debug in a single line
Just so it is grouped logically in line with other data and makes a
rather verbose output a bit shorter.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 13 May 2015 12:34:04 +0000 (15:34 +0300)]
drm/i915/bios: abstract finding VBT in BIOS to a separate function
Improve clarity. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 13 May 2015 12:34:03 +0000 (15:34 +0300)]
drm/i915/bios: remove a redundant NULL pointer check
We never pass a non-NULL vbt to validate_vbt, and we can safely expect
the callers to not change.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Fri, 15 May 2015 14:07:02 +0000 (15:07 +0100)]
drm/i915/skl: Remove unnecessary local variables in skl_plane_ctl*()
Ville noticed in another patch we we didn't need them at all, so remove
them. It's worth saying that it makes no difference to code generated as
gcc is clever enough to optimize it out.
v2: Remove 'break' after 'return' in switches (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 13 May 2015 07:35:25 +0000 (10:35 +0300)]
drm/i915/dsi: add support for DSI PLL N1 divisor values
Currently DSI PLL N1 is hardcoded off. Make it possible to use it
later. This should have no functional changes for now.
v2: s/ffz(~(n))/ffs(n) - 1/ (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Animesh Manna [Wed, 13 May 2015 16:43:29 +0000 (22:13 +0530)]
drm/i915/skl: Documentation for CSR firmware
Added docbook info regarding context save and restore (CSR)
firmware support added from gen9 onwards to drive newly added
DMC (Display microcontroller) in display engine.
v1: Initial version as RFC.
v2: Used "DOC:" tag for csr description based on review comment from Daniel.
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Fri, 15 May 2015 10:09:21 +0000 (13:09 +0300)]
drm/i915: Don't read dpcd for disconnected ports
Reading from disconnected ports will spit out timeout error
on the dmesg. Skip the attempted read if the port is not
connected and avoid confusing users/testcases about
expected timeouts.
This new dpcd debugfs entry was introduced by commit
aa7471d228eb
("drm/i915: add i915 specific connector debugfs file for DPCD")
v2 by Jani: move the check at the top, out of the loop.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90060
Tested-by: yex.tian@intel.com
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dan Carpenter [Tue, 12 May 2015 18:07:37 +0000 (21:07 +0300)]
drm/edid: fix a debug message
There is an extra semi-colon on the if statement so the debug output
always says "Failed to write EDID checksum" even when it didn't fail.
Fixes:
559be30cb74d ('drm/i915: Implement the intel_dp_autotest_edid function for DP EDID complaince tests')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 12 May 2015 15:13:22 +0000 (16:13 +0100)]
drm/i915: Make the sprite formats const
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 12 May 2015 15:13:18 +0000 (16:13 +0100)]
drm/i915: Don't use the intel_ prefix for gen-specific data
We now prefix our functions/enums/data with the first platform it has
been introduced. Do that for the primary plane formats.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: s/gen2/i8xx/ and s/gen4/i965/ ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 12 May 2015 15:13:17 +0000 (16:13 +0100)]
drm/i915/skl: Support the advertized index format
We advertize C8 in the primary plane formats didn't have the
corresponding code to set PLANE_CTL accordingly.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 12 May 2015 15:13:16 +0000 (16:13 +0100)]
drm/i915/skl: Replace BUG() by MISSING_CASE() in skl_plane_ctl_format()
Let's be consistent with the others skl_plane_ctl_*() functions and use
a MISSING_CASE(). Not only that, but it's a rude to BUG() the whole
machine here.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 12 May 2015 15:13:15 +0000 (16:13 +0100)]
drm/i915/skl: Rename a local variable to fit in 80 chars
No reason to not follow the 80 chars rule, renaming the local variable
makes it easy.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 12 May 2015 15:13:14 +0000 (16:13 +0100)]
drm/i915/skl: Add a new line before return
We usually use a new line before those kind of return statements. Also
the various skl_plane_ctl*() functions weren't consistent.
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 12 May 2015 15:13:13 +0000 (16:13 +0100)]
drm/i915/skl: Leave a new line between variable declarations and code
Cc: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 12 May 2015 12:23:09 +0000 (15:23 +0300)]
drm/i915: clean up dsi pll calculation
Improve readability. No functional changes.
v2: use more rational types (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 6 May 2015 12:33:44 +0000 (15:33 +0300)]
drm/i915: don't register invalid gmbus pins for skl
Do not expose invalid gmbus pins as i2c devices to userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 6 May 2015 12:33:43 +0000 (15:33 +0300)]
drm/i915: don't register invalid gmbus pins for bdw
Do not expose invalid gmbus pins as i2c devices to userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 12 May 2015 12:41:32 +0000 (15:41 +0300)]
drm/i915: constify validate_vbt in VBT parsing
Make input and output of validate_vbt const, and fix the fallout. We
shouldn't modify the VBT, so make the compiler help us here.
v2: use pointer arithmetics on void* to simplify (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Wed, 15 Apr 2015 12:18:28 +0000 (15:18 +0300)]
drm/i915: constify find_section in VBT parsing
Make input and output of find_section const, and fix the fallout. We
shouldn't modify the VBT, so make the compiler help us here.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 11 May 2015 17:49:10 +0000 (20:49 +0300)]
drm/i915: Use HOTPLUG_INT_STATUS_G4X on VLV/CHV
Use HOTPLUG_INT_STATUS_G4X instead of HOTPLUG_INT_STATUS_I915 on VLV/CHV
so that we don't confuse the AUX status bits with SDVO status bits.
Avoid pointless log spam as below while handling AUX interrupts:
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_hpd_irq_handler] hotplug event received, stat 0x00000040, dig 0x00000000
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x71450064
Note that there's no functional issue, it's just that the sdvo bits
overlap with the dp aux bits. Hence every time we receive an aux
interrupt we also think there's an sdvo hpd interrupt, but due to lack
of any sdvo encoders nothing ever happens because of that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add Ville's explanation why nothing functional really
changes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 11 May 2015 17:49:09 +0000 (20:49 +0300)]
drm/i915: Remove excess inline keywords
Remove some inline keywords. One of the functions has clearly outgrown
it anyway, so let's just leave it to the compiler.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Tue, 12 May 2015 07:35:08 +0000 (10:35 +0300)]
drm/i915/gtt: Fix the boundary check for vm area
The check for start + length >= total_vm_size is
wrong since start + length can be exactly the size of
the vm.
Fix the check to allow allocation to boundary.
Fixes a regression in commit
4dd738e9cd79
("drm/i915: Fix 32b overflow check in gen8_ppgtt_alloc_page_directories")
Testcase: igt/gem_evict_everything/swapping-interruptible
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90399
Tested-by: Lu Hua <huax.lu@intel.com>
Cc: Chris Wilson <chris@chris.wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chandra Konduru [Mon, 11 May 2015 21:35:47 +0000 (14:35 -0700)]
drm/i915: Make scaler_id check in check_crtc_state work for all gens
During check_crtc_state, scaler_id mispatch is being reported for HSW.
This is applicable for skl+ and not for HSW. It is introduced by
commit id:
commit
a1b2278e4dfcd2dbea85e319ebf73a6b7b2f180b
Author: Chandra Konduru <chandra.konduru@intel.com>
Date: Tue Apr 7 15:28:45 2015 -0700
drm/i915: skylake panel fitting using shared scalers
This patch will make sure that we leave scaler_id as 0 for platforms
before skl and set for skl+ only. This way scaler_id check during
check_crtc_state will pass for both prior to skl and skl+ platforms.
v2:
-Leave scaler_id as 0 for gen < 9 (Daniel)
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
References: http://lists.freedesktop.org/archives/intel-gfx/2015-May/065741.html
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:16 +0000 (13:41 +0100)]
drm/i915: Fix race on unreferencing the wrong mmio-flip-request
As we perform the mmio-flip without any locking and then try to acquire
the struct_mutex prior to dereferencing the request, it is possible for
userspace to queue a new pageflip before the worker can finish clearing
the old state - and then it will clear the new flip request. The result
is that the new flip could be completed before the GPU has finished
rendering.
The bugs stems from removing the seqno checking in
commit
536f5b5e86b225dab94c7ff8061ae482b6077387
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Thu Nov 6 11:03:40 2014 +0200
drm/i915: Make mmio flip wait for seqno in the work function
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:15 +0000 (13:41 +0100)]
drm/i915: Ensure cache flushes prior to doing CS flips
Synchronising to an object active on the same ring is a no-op, for the
benefit of execbuffer scheduler. However, for CS flips this means that
we can forgo checking whether the last write request of the object is
actually queued and more importantly whether the cache flush for the
write was emitted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Mon, 27 Apr 2015 12:41:14 +0000 (13:41 +0100)]
drm/i915: Remove domain flubbing from i915_gem_object_finish_gpu()
We no longer interpolate domains in the same manner, and even if we did,
we should trust setting either of the other write domains would trigger
an invalidation rather than force it. Remove the tweaking of the
read_domains since it serves no purpose and use
i915_gem_object_wait_rendering() directly.
Note that this goes back to
commit
a8198eea156df47e0e843ac5c7d4c8774e121c42
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Apr 13 22:04:09 2011 +0100
drm/i915: Introduce i915_gem_object_finish_gpu()
and gpu domain tracking died in
commit
cc889e0f6ce6a63c62db17d702ecfed86d58083f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 13 20:45:19 2012 +0200
drm/i915: disable flushing_list/gpu_write_list
which is more than 1 year older.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add notes with information dug out of git history.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Peter Antoine [Mon, 11 May 2015 15:03:27 +0000 (16:03 +0100)]
drm/i915: Warn when execlists changes context without IRQs
If an batch ends while the IRQs are not turned on the notification can
go missing and the GPU can hang. So generate a warning in this case.
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chandra Konduru [Sat, 9 May 2015 03:22:46 +0000 (20:22 -0700)]
drm/i915: call intel_tile_height with correct parameter
In skylake update plane functions, intel_tile_height() is called with
bits_per_pixel instead of pixel_format. Correcting it.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
[danvet: Fixup alignment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tvrtko Ursulin [Fri, 8 May 2015 12:02:36 +0000 (13:02 +0100)]
drm/i915: Remove duplicated intel_tile_height declaration
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Deepak S [Sat, 9 May 2015 12:45:46 +0000 (18:15 +0530)]
drm/i915/chv: Set min freq to efficient frequency on chv
After feedback from the hardware team, now we set the GPU min/idel freq to RPe.
Punit is expecting us to operate GPU between Rpe & Rp0. If we drop the
frequency to RPn, punit is failing to change the vgg input voltage to
minimum :(
Since Punit validates the rps range [RPe, RP0]. This patch
removes unused cherryview_rps_min_freq function.
v2: Change commit message
v3: set min_freq before idle_freq (chris)
v4: Squash 'Remove unused rps min function' patch
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>