OSDN Git Service
Ricardo Neri [Wed, 1 Aug 2012 12:56:40 +0000 (07:56 -0500)]
OMAPDSS: DISPC: Improvements to DIGIT sync signal selection
DSS code wrongly assumes that VENC is always available as source for the external
sync signal for the display controller DIGIT channel. One cannot blindly write/read
the value of DSS_CONTROL[15] as in certain processors (e.g., OMAP5) this operation
may not be valid. If the the sync source is not read correctly, the callers of
dss_get_hdmi_venc_clk_source might make wrong assumptions about, for instance,
video timings.
Logic is added to correctly get the sync signal based on the available displays
in the DIGIT channel. The source is set only if both VENC and HDMI are supported.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Jassi Brar [Tue, 24 Jul 2012 14:03:55 +0000 (19:33 +0530)]
OMAPDSS: DISPC: Use msleep instead of blocking mdelay
We have no reason to block in the error handler workqueue, so use msleep.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Ricardo Neri [Tue, 31 Jul 2012 00:12:02 +0000 (19:12 -0500)]
OMAPDSS: HDMI: Disable PLL properly in case of error at power_on
Small patch to disable the PLL appropriately before runtime_put in case
an error occurs while enabling the PHY.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 29 Jun 2012 11:13:07 +0000 (14:13 +0300)]
Merge "Apply LCD manager related parameters" from Archit
The LCD interface drivers(DPI, DSI, RFBI, SDI) do some direct DISPC register
writes to configure LCD manager related fields. This series groups these fields
into a single struct, and let's the interface driver apply these parameters.
This allows us to:
- Check the LCD manager related parameters before applying them.
- Remove some omap_dss_device references as APPLY holds the applied parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Mon, 25 Jun 2012 09:28:48 +0000 (14:58 +0530)]
OMAPDSS: OVERLAY: Clean up replication checking
Replication logic for an overlay depends on the color mode in which it is
configured and the video port width of the manager it is connected to.
video port width now held in dss_lcd_mgr_config in the manager's private
data in APPLY. Use this instead of referring to the omap_dss_device connected to
the manager.
Replication is enabled in the case of TV manager, the video_port_width is set to
a default value of 24 for TV manager.
Make the replication checking an overlay function since it's more of an overlay
characteristic than a display characteristic.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Tue, 29 May 2012 06:25:38 +0000 (11:55 +0530)]
OMAPDSS: RFBI: Use dss_mgr_enable to enable the overlay manager
The RFBI driver uses a direct DISPC register write to enable the overlay
manager. Replace this with dss_mgr_enable() which checks if the connected
overlay and managers are correctly configured, and configure DSS for
fifomerge.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Fri, 29 Jun 2012 09:11:30 +0000 (14:41 +0530)]
OMAPDSS: DISPC: Remove a redundant function
dss_mgr_is_lcd() available in dss.h does the same thing as dispc_mgr_is_lcd()
in dispc.c. Remove the function from dispc.c and replace it with the one in
dss.h.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Thu, 24 May 2012 09:38:54 +0000 (15:08 +0530)]
OMAPDSS: APPLY: Remove usage of omap_dss_device from manual/auto update checks
APPLY needs to know at certain places whether an overlay manager is in manual
or auto update mode. The caps of the connected omap_dss_device were used to
check that.
A LCD manager is in manual update if stallmode is enabled for that manager. TV
managers for now always auto update.
Return the value of stallmode parameter in the private data 'lcd_confg' in
mgr_manual_update() and ovl_manual_update(), for TV managers stallmode field
will be false by default.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Wed, 23 May 2012 11:31:35 +0000 (17:01 +0530)]
OMAPDSS: MANAGER: Check LCD related overlay manager parameters
The LCD related manager configurations are a part of the manager's private data
in APPLY. Pass this to dss_lcd_mgr_config to dss_mgr_check and create a function
to check the validity of some of the configurations.
To check some of the configurations, we require information of interface to
which the manager output is connected. These can be added once interfaces are
represented as an entity.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Fri, 29 Jun 2012 09:07:03 +0000 (14:37 +0530)]
OMAPDSS: APPLY: Remove DISPC writes to manager's lcd parameters in interface drivers
Replace the DISPC fuctions used to configure LCD channel related manager
parameters with dss_mgr_set_lcd_config() in APPLY. This function ensures that
the DISPC registers are written at the right time by using the shadow register
programming model.
The LCD manager configurations is stored as a private data of manager in APPLY.
It is treated as an extra info as it's the panel drivers which trigger this
apply via interface drivers, and not a DSS2 user like omapfb or omapdrm.
Storing LCD manager related properties in APPLY also prevents the need to refer
to the panel connected to the manager for information. This helps in making the
DSS driver less dependent on panel.
A helper function is added to check whether the manager is LCD or TV. The direct
DISPC register writes are removed from the interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Fri, 29 Jun 2012 09:03:18 +0000 (14:33 +0530)]
OMAPDSS: SDI: Configure dss_lcd_mgr_config struct with lcd manager parameters
Create a dss_lcd_mgr_config struct instance in SDI. Fill up all the parameters
of the struct with configurations held by the panel, and the configurations
required by SDI.
Use these to write to the DISPC registers. These direct register writes would be
later replaced by a function which applies the configuration using the shadow
register programming model.
Create function sdi_config_lcd_manager() which fills the mgr_config parameters
and writes to the DISPC registers.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Fri, 29 Jun 2012 09:01:07 +0000 (14:31 +0530)]
OMAPDSS: DSI: Configure dss_lcd_mgr_config struct with lcd manager parameters
Create a dss_lcd_mgr_config struct instance in DSI. Fill up all the parameters
of the struct with configurations held by the panel, and the configurations
required by DSI.
Use these to write to the DISPC registers. These direct register writes would be
later replaced by a function which applies the configuration using the shadow
register programming model.
The function dsi_configure_dispc_clocks() is now called in
dsi_display_init_dispc(), this lets all the lcd manager related configurations
happen in the same place. The DISPC_DIVISORo register was written in
dsi_configure_dispc_clock(), now it just fills up the dispc_clock_info parameter
in mgr_config. The clock_info is written later in dsi_display_init_dispc().
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Mon, 25 Jun 2012 05:54:10 +0000 (11:24 +0530)]
OMAPDSS: RFBI: Configure dss_lcd_mgr_config struct with lcd manager parameters
Create a dss_lcd_mgr_config struct instance in RFBI. Fill up all the parameters
of the struct with configurations held by the panel, and the configurations
required by RFBI.
Use these to write to the DISPC registers. These direct register writes would be
later replaced by a function which applies the configuration using the shadow
register programming model.
Create function rfbi_config_lcd_manager() which fills up the mgr_config
parameters and writes to the DISPC regs.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Fri, 29 Jun 2012 08:49:13 +0000 (14:19 +0530)]
OMAPDSS: DPI: Configure dss_lcd_mgr_config struct with lcd manager parameters
Create a dss_lcd_mgr_config struct instance in DPI. Fill up all the parameters
of the struct with configurations held by the panel, and the configurations
required by DPI.
Use these to write to the DISPC registers. These direct register writes would be
later replaced by a function which applies the configuration using the shadow
register programming model.
The DISPC_DIVISORo registers were written in the functions dpi_set_dispc_clk()
and dpi_set_dsi_clk(), now they just fill up the dispc_clock_info parameter in
mgr_config. They are written later in dpi_config_lcd_manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Fri, 29 Jun 2012 08:33:48 +0000 (14:03 +0530)]
OMAPDSS: Add struct to hold LCD overlay manager configuration
Create a struct dss_lcd_mgr_config which holds LCD overlay manager related
parameters. These are currently partially contained in the omap_dss_device
connected to the manager, and the rest are in the interface driver.
The parameters are directly written to the DISPC registers in the interface
drivers. These should eventually be applied at the correct time using the
shadow register programming model. This struct would help in grouping these
parameters so that they can be applied together.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Fri, 29 Jun 2012 08:30:54 +0000 (14:00 +0530)]
OMAPDSS: DISPC: Change return type of dispc_mgr_set_clock_div()
dipsc_mgr_set_clock div has an int return type to report errors or success.
The function doesn't really check for errors and always returns 0. Change
the return type to void.
Checking for the correct DISPC clock divider ranges will be done when a DSS2
user does a manager apply. This support will be added later.
Signed-off-by: Archit Taneja <archit@ti.com>
Chandrabhanu Mahapatra [Thu, 28 Jun 2012 09:44:02 +0000 (15:14 +0530)]
ARM: OMAP2PLUS: DSS: Disable LCD3 output when resetting DSS
The dispc_disable_outputs() function currently disables all LCD managers except
LCD3. This patch adds disabling functionality for LCD3 manager thereby
maintaining consistency of Display Subsystem for in case Display Controller is
reset when LCD3 manager is in use.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Fri, 29 Jun 2012 07:18:33 +0000 (10:18 +0300)]
Merge Misc DSS clean ups from Archit
This series does the following things:
- Remove passive matrix LCD support: There are no panel drivers with
passive matrix LCD drivers in DSS2. There are no passive matrix panels
even available to test with DSS. Since no one is using passive matrix
panels, stop trying to support it. It cleans up the DSS driver.
- Add some new fields to omap_video_timings: There were some standard
panel timing fields missing from omap_video_timings. Namely
Hsync/Vsync/DE levels and interlace. Add these to omap_video_timings
to align it more with xorg modeline. Add some other OMAP DSS specific
fields to omap_video_timings.
- Remove some hacks done because omap_video_timings didn't have the
above fields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Tue, 26 Jun 2012 07:08:31 +0000 (12:38 +0530)]
OMAPDSS: DSI: Fix HSYNC, VSYNC and DE polarities between DISPC and DSI
For DSI operation in videomode, DISPC logic levels for the signals HSYNC, VSYNC
and DE need to be specified to DSI via the fields VP_HSYNC_POL, VP_VSYNC_POL and
VP_DE_POL in DSI_CTRL registers.
This information is completely internal to DSS as logic levels for the above
signals hold no meaning on the DSI bus. Hence a DSI panel driver should be
totally oblivious of these fields.
Fix the logic levels/polarities in the DISPC and DSI registers to a default
value. This is done by overriding these fields in omap_video_timings struct
filled by the panel driver for DISPC, and use the equivalent default values
when programming DSI_CTRL registers. Also, remove the redundant polarity related
fields in omap_dss_dsi_videomode_data.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Sun, 24 Jun 2012 07:38:10 +0000 (13:08 +0530)]
OMAPDSS: HDMI: Remove custom hdmi_video_timings struct
The hdmi CEA and VESA timings were represented by the struct hdmi_video_timings,
omap_video_timings couldn't be used as it didn't contain the fields hsync/vsync
polarities and interlaced/progressive information.
Remove hdmi_video_timings, and use omap_video_timings instead.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Thu, 28 Jun 2012 12:53:18 +0000 (18:23 +0530)]
OMAPFB: Map interlace field in omap_video_timings with fb vmode flags
Use the interlace field in omap_video_timings to configure/retrieve
corresponding fb mode flags in fb_var_screeninfo and fb_videomode.
The interlace field maps with the fb mode flags FB_VMODE_INTERLACED and
FB_VMODE_NONINTERLACED.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Wed, 6 Jun 2012 10:55:52 +0000 (16:25 +0530)]
OMAPDSS: DISPC/APPLY: Use interlace info in manager timings for dispc_ovl_setup()
Currently the interlace parameter passed to dispc_ovl_setup() is configured by
checking the display type, and set to true if the display type is VENC.
This isn't correct as other panels can take interlaced content too. The
omap_video_timings struct in manager's private data contains the info whether
the panel is in interlaced mode or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Thu, 28 Jun 2012 05:45:51 +0000 (11:15 +0530)]
OMAPDSS: Add interlace parameter to omap_video_timings
Add a parameter called interlace which tells whether the timings are in
interlaced or progressive mode. This aligns the omap_video_timings struct with
the Xorg modeline configuration.
It also removes the hack needed to write to divide the manager height by 2 if
the connected interface is VENC.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Fri, 29 Jun 2012 06:43:32 +0000 (12:13 +0530)]
OMAPDSS: Remove omap_panel_config enum from omap_dss_device
omap_panel_config contains fields which are finally written to DISPC_POL_FREQo
registers. These are now held by omap_video_timings and are set when the manager
timings are applied.
Remove the omap_panel_config enum, and remove all it's references from panel or
interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Fri, 15 Jun 2012 02:09:47 +0000 (07:39 +0530)]
OMAPFB: Map the newly added omap_video_timings fields with fb sync flags
Use the newly added fields in omap_video_timings(hsync, vsync and data_enable
logic levels and data, hsync and vsync latching related info) to
configure/retrieve corresponding sync flags in fb_var_screeninfo and
fb_videomode.
Out of the new fields, hsync_level and vsync_level can be mapped to the fb sync
flags FB_SYNC_HOR_HIGH_ACT and FB_SYNC_VERT_HIGH_ACT.
When converting fb mode to omap_video_timings, the fields which don't have an
equivalent parameter in fb are kept as the original values if the panel driver
has a get_timings op, else they are set to default values.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Mon, 25 Jun 2012 07:04:22 +0000 (12:34 +0530)]
OMAPDSS: DISPC: Remove dispc_mgr_set_pol_freq()
dispc_mgr_set_pol_freq() configures the fields in the register DISPC_POL_FREQo.
All these fields have been moved to omap_video_timings struct, and are now
programmed in dispc_mgr_set_lcd_timings(). These will be configured when timings
are applied via dss_mgr_set_timings().
Remove dispc_mgr_set_pol_freq() and it's calls from the interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Thu, 21 Jun 2012 05:07:43 +0000 (10:37 +0530)]
OMAPDSS: DISPC: Configure newly added omap_video_timing fields
Hsync, Vsync, Data enable enable logic levels and latching info of Data lanes,
Hsync and Vsync signals(with respect to pixel clock) are newly added parameters
in omap_video_timings.
Program these in dispc_mgr_set_lcd_timings. These will be configured when the
manager's timings are set via dss_mgr_set_timings().
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Thu, 21 Jun 2012 07:51:02 +0000 (13:21 +0530)]
OMAPDSS: DISPLAY: Ignore newly added omap_video_timings fields for display timings sysfs file
The display sysfs file for viewing/storing display timings is something which
will be deprecated. The new omap_video_timings fields (hsync_level, vsync_level
and others) are not configurable or viewable via this sysfs file.
This prevents the need to make the input more configurable to take the new
fields and at the same time work without these fields for backward
compatibility.
In display_timings_store, the omap_video_timings struct used to set the timings
is initialized to the existing panel timings so that the new fields are taken in
correctly. The other fields are taken from the user as before.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Mon, 25 Jun 2012 06:56:38 +0000 (12:26 +0530)]
OMAPDSS: Add some new fields to omap_video_timings
Some panel timing related fields are contained in omap_panel_config in the form
of flags. The fields are:
- Hsync logic level
- Vsync logic level
- Data driven on rising/falling edge of pixel clock
- Output enable/Data enable logic level
- HSYNC/VSYNC driven on rising/falling edge of pixel clock
Out of these parameters, Hsync and Vsync logic levels are a part of the timings
in the Xorg modeline configuration. So it makes sense to move the to
omap_video_timings. The rest aren't a part of modeline, but it still makes
sense to move these since they are related to panel timings.
These fields stored in omap_panel_config in dssdev are configured for LCD
panels, and the corresponding LCD managers in the DISPC_POL_FREQo registers.
Add the above fields in omap_video_timings. Represent their state via new enums.
Add these parameters to the omap_video_timings instances in the panel drivers.
Keep the corresponding IVS, IHS, IPC, IEO, RF and ONOFF flags in
omap_panel_config for now. The struct will be removed later.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Mon, 25 Jun 2012 06:46:22 +0000 (12:16 +0530)]
OMAPDSS: Remove passive matrix LCD support (part 4)
Remove configuration of Ac-bias pins
Ac-bias pins need to be configured only for passive matrix displays. Remove
acbi and acb fields in omap_dss_device and their configuration in panel
drivers. Don't program these fields in DISP_POL_FREQo register any more.
The panel driver for sharp-ls037v7dw01, and the panel config for
Innolux AT070TN8 in generic dpi panel driver set acb to a non zero value. This
is most likely carried over from the old omapfb driver which supported passive
matrix displays.
Cc: Thomas Weber <weber@corscience.de>
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Thu, 21 Jun 2012 04:15:11 +0000 (09:45 +0530)]
OMAPDSS: Remove passive matrix LCD support (part 3)
Remove omap_lcd_display_type enum
The enum omap_lcd_display_type is used to configure the lcd display type in
DISPC. Remove this enum and always set display type to TFT by creating function
dss_mgr_set_lcd_type_tft().
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Thu, 21 Jun 2012 04:11:10 +0000 (09:41 +0530)]
OMAPDSS: Remove passive matrix LCD support (part 2)
Remove OMAP_DSS_LCD_TFT as a omap_panel_config flag.
We don't support passive matrix displays any more. Remove this flag from all the
panel drivers.
Force the display_type to OMAP_DSS_LCD_DISPLAY_TFT in the interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Archit Taneja [Thu, 21 Jun 2012 04:03:55 +0000 (09:33 +0530)]
OMAPDSS: Remove passive matrix LCD support (part 1)
Remove clock constraints related to passive matrix displays.
There is a constraint (pcd_min should be 3) for passive matrix displays. Remove
this constraint in clock divider calculations as we won't support passive
matrix displays any more.
This cleans up the functions which calculate the clock dividers with DSI's PLL
or DSS_FCLK as the clock source.
Signed-off-by: Archit Taneja <archit@ti.com>
Jassi Brar [Wed, 27 Jun 2012 14:04:56 +0000 (19:34 +0530)]
OMAPDSS: HDMI: Replace spinlock with mutex in hdmi_check_hpd_state
State change of HDMI PHY could potentially take many millisecs, we can do
better by protecting things in hdmi_set_phy_pwr() with a mutex rather than
a spin_lock_irqsave.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Jassi Brar [Wed, 27 Jun 2012 14:04:36 +0000 (19:34 +0530)]
OMAPDSS: HDMI: Discard phy_tx_enabled member
It is simpler to read the current status from a register as compared
to maintaining a state variable to hold the information.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Chandrabhanu Mahapatra [Thu, 21 Jun 2012 05:53:56 +0000 (11:23 +0530)]
OMAPDSS: Add dump and debug support for LCD3
DISPC functions have been modified to provide clock and register dumps and debug
support for the LCD3 manager.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Chandrabhanu Mahapatra [Fri, 29 Jun 2012 05:13:13 +0000 (10:43 +0530)]
OMAPDSS: Add LCD3 overlay manager and Clock and IRQ support
The support for LCD3 manager has been added into the manager module. LCD3 panel
has registers as DISPC_CONTROL3 and DISPC_CONFIG3 just like those in LCD and
LCD2 panels. These registers control the Display Controller (DISPC) module for
LCD3 output. The three LCDs support Display Serial Interface (DSI), Remote Frame
Buffer Interface (RFBI) and Parallel CMOS Output Interface (DPI). These LCDs can
be connected through parallel output interface using DISPC and RFBI or DPI. For
serial interface DSS uses DSI.
The LCD3 panel, just like LCD and LCD2 panels, has a clock switch in DSS_CTRL
register which has been enabled. The clock switch chooses between DSS_CLK and
DPLL_DSI1_C_CLK1 as source for LCD3_CLK. New IRQs as DISPC_IRQ_VSYNC3,
DISPC_IRQ_FRAMEDONE3, DISPC_IRQ_ACBIAS_COUNT_STAT3 and DISPC_IRQ_SYNC_LOST3 have
been added specific to the new manager.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Chandrabhanu Mahapatra [Tue, 19 Jun 2012 09:38:16 +0000 (15:08 +0530)]
OMAPDSS: Add support for LCD3 channel
OMAP5 Display Subsystem (DSS) architecture comes with a additional LCD3 channel
with its own dedicated overlay manager. The current patch adds LCD3 channel and
basic register support for LCD3 channel. It adds register addresses for various
Display Controller (DISPC) registers like DISPC_DEFAULT_COLOR, DISPC_TIMING_H,
DISPC_DIVISORo, etc.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Chandrabhanu Mahapatra [Thu, 21 Jun 2012 05:37:44 +0000 (11:07 +0530)]
OMAPDSS: Cleanup implementation of LCD channels
The current implementation of LCD channels and managers consists of a number of
if-else construct which has been replaced by a simpler interface. A constant
structure mgr_desc has been created in Display Controller (DISPC) module. The
mgr_desc contains for each channel its name, irqs and is initialized one time
with all registers and their corresponding fields to be written to enable
various features of Display Subsystem. This structure is later used by various
functions of DISPC which simplifies the further implementation of LCD channels
and its corresponding managers.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 27 Jun 2012 13:37:18 +0000 (16:37 +0300)]
OMAPDSS: fix warnings if CONFIG_PM_RUNTIME=n
If runtime PM is not enabled in the kernel config, pm_runtime_get_sync()
will always return 1 and pm_runtime_put_sync() will always return
-ENOSYS. pm_runtime_get_sync() returning 1 presents no problem to the
driver, but -ENOSYS from pm_runtime_put_sync() causes the driver to
print a warning.
One option would be to ignore errors returned by pm_runtime_put_sync()
totally, as they only say that the call was unable to put the hardware
into suspend mode.
However, I chose to ignore the returned -ENOSYS explicitly, and print a
warning for other errors, as I think we should get notified if the HW
failed to go to suspend properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Tomi Valkeinen [Tue, 26 Jun 2012 12:52:16 +0000 (15:52 +0300)]
OMAPDSS: Use PM notifiers for system suspend
The current way how omapdss handles system suspend and resume is that
omapdss device (a platform device, which is not part of the device
hierarchy of the DSS HW devices, like DISPC and DSI, or panels.) uses
the suspend and resume callbacks from platform_driver to handle system
suspend. It does this by disabling all enabled panels on suspend, and
resuming the previously disabled panels on resume.
This presents a few problems.
One is that as omapdss device is not related to the panel devices or the
DSS HW devices, there's no ordering in the suspend process. This means
that suspend could be first ran for DSS HW devices and panels, and only
then for omapdss device. Currently this is not a problem, as DSS HW
devices and panels do not handle suspend.
Another, more pressing problem, is that when suspending or resuming, the
runtime PM functions return -EACCES as runtime PM is disabled during
system suspend. This causes the driver to print warnings, and operations
to fail as they think that they failed to bring up the HW.
This patch changes the omapdss suspend handling to use PM notifiers,
which are called before suspend and after resume. This way we have a
normally functioning system when we are suspending and resuming the
panels.
This patch, I believe, creates a problem that somebody could enable or
disable a panel between PM_SUSPEND_PREPARE and the system suspend, and
similarly the other way around in resume. I choose to ignore the problem
for now, as it sounds rather unlikely, and if it happens, it's not
fatal.
In the long run the system suspend handling of omapdss and panels should
be thought out properly. The current approach feels rather hacky.
Perhaps the panel drivers should handle system suspend, or the users of
omapdss (omapfb, omapdrm) should handle system suspend.
Note that after this patch we could probably revert
0eaf9f52e94f756147dbfe1faf1f77a02378dbf9 (OMAPDSS: use sync versions of
pm_runtime_put). But as I said, this patch may be temporary, so let's
leave the sync version still in place.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Jassi Brar <jaswinder.singh@linaro.org>
Tested-by: Jassi Brar <jaswinder.singh@linaro.org>
Rajendra Nayak [Wed, 27 Jun 2012 08:51:26 +0000 (14:21 +0530)]
OMAPDSS: add clk_prepare_enable and clk_disable_unprepare
In preparation of OMAP moving to Common Clk Framework(CCF) change
clk_enable() and clk_disable() calls to clk_prepare_enable() and
clk_disable_unprepare() in omapdss. This can be safely done, as omapdss
never enables or disables clocks in atomic context.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: <linux-fbdev@vger.kernel.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
[tomi.valkeinen@ti.com: updated patch description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Peter Meerwald [Wed, 27 Jun 2012 20:09:22 +0000 (22:09 +0200)]
OMAPDSS: fix specification spelling in Kconfig
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Mon, 25 Jun 2012 08:20:13 +0000 (11:20 +0300)]
OMAPDSS: remove enum omap_dss_overlay_managers
We have two almost the same enums: omap_channel and
omap_dss_overlay_managers. omap_channel is used almost everywhere, and
omap_channel assigns explicit values to the enum values which are needed
for proper operation.
omap_dss_overlay_managers is only used in one place, so it's easy to
remove it, which is what this patch does.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen [Wed, 13 Jun 2012 08:24:38 +0000 (11:24 +0300)]
Merge tag 'v3.5-rc2'
Merge v3.5-rc2 to get latest device tree and dynamic debug changes.
Linus Torvalds [Sat, 9 Jun 2012 01:40:09 +0000 (18:40 -0700)]
Linux 3.5-rc2
David Rientjes [Fri, 8 Jun 2012 20:21:26 +0000 (13:21 -0700)]
mm, oom: fix badness score underflow
If the privileges given to root threads (3% of allowable memory) or a
negative value of /proc/pid/oom_score_adj happen to exceed the amount of
rss of a thread, its badness score overflows as a result of commit
a7f638f999ff ("mm, oom: normalize oom scores to oom_score_adj scale only
for userspace").
Fix this by making the type signed and return 1, meaning the thread is
still eligible for kill, if the value is negative.
Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 8 Jun 2012 21:59:29 +0000 (14:59 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar.
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix the relax_domain_level boot parameter
sched: Validate assumptions in sched_init_numa()
sched: Always initialize cpu-power
sched: Fix domain iteration
sched/rt: Fix lockdep annotation within find_lock_lowest_rq()
sched/numa: Load balance between remote nodes
sched/x86: Calculate booted cores after construction of sibling_mask
Randy Dunlap [Fri, 8 Jun 2012 20:18:33 +0000 (13:18 -0700)]
sched/fair: fix lots of kernel-doc warnings
Fix lots of new kernel-doc warnings in kernel/sched/fair.c:
Warning(kernel/sched/fair.c:3625): No description found for parameter 'env'
Warning(kernel/sched/fair.c:3625): Excess function parameter 'sd' description in 'update_sg_lb_stats'
Warning(kernel/sched/fair.c:3735): No description found for parameter 'env'
Warning(kernel/sched/fair.c:3735): Excess function parameter 'sd' description in 'update_sd_pick_busiest'
Warning(kernel/sched/fair.c:3735): Excess function parameter 'this_cpu' description in 'update_sd_pick_busiest'
.. more warnings
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 8 Jun 2012 21:53:06 +0000 (14:53 -0700)]
Revert "drm/i915/crt: Do not rely upon the HPD presence pin"
This reverts commit
9e612a008fa7fe493a473454def56aa321479495.
It incorrectly finds VGA connectors where none are attached, apparently
not noticing that nothing replied to the EDID queries, and happily using
the default EDID modes that have nothing to do with actual hardware.
That in turn then causes X to fall down to the lowest common
denominator, which is usually the default 1024x768 mode that is in the
default EDID and pretty much anything supports).
I'd suggest that if not relying on the HDP pin, the code should at least
check whether it gets valid EDID data back, rather than just assume
there's something on the VGA connector.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 8 Jun 2012 18:15:31 +0000 (11:15 -0700)]
Merge tag 'ext4_for_linus' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Theodore Ts'o:
"This update contains two bug fixes, both destined for the stable tree.
Perhaps the most important is one which fixes ext4 when used with file
systems originally formatted for use with ext3, but then later
converted to take advantage of ext4."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: don't set i_flags in EXT4_IOC_SETFLAGS
ext4: fix the free blocks calculation for ext3 file systems w/ uninit_bg
Linus Torvalds [Fri, 8 Jun 2012 18:06:01 +0000 (11:06 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/paulus/powerpc
Pull powerpc fixes from Paul Mackerras:
"Two small fixes for powerpc:
- a fix for a regression since 3.2 that causes 4-second (or longer)
pauses
- a fix for a potential oops when loading kernel modules on 32-bit
embedded systems."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix kernel panic during kernel module load
powerpc/time: Sanity check of decrementer expiration is necessary
Linus Torvalds [Fri, 8 Jun 2012 18:04:06 +0000 (11:04 -0700)]
Merge tag 'upstream-3.5-rc2' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS fixes from Artem Bityutskiy:
"Fix UBI and UBIFS - they refuse to work without debugfs. This was
broken by the 3.5-rc1 UBI/UBIFS changes when we removed the debugging
Kconfig switches.
Also, correct locking in 'ubi_wl_flush()' - it was extended to support
flushing a specific LEB in 3.5-rc1, and the locking was sub-optimal."
* tag 'upstream-3.5-rc2' of git://git.infradead.org/linux-ubifs:
UBI: correct ubi_wl_flush locking
UBIFS: fix debugfs-less systems support
UBI: fix debugfs-less systems support
Linus Torvalds [Fri, 8 Jun 2012 17:34:03 +0000 (10:34 -0700)]
Revert "vfs: stop d_splice_alias creating directory aliases"
This reverts commit
7732a557b1342c6e6966efb5f07effcf99f56167 (and commit
3f50fff4dace23d3cfeb195d5cd4ee813cee68b7, which was a follow-up
cleanup).
We're chasing an elusive bug that Dave Jones can apparently reproduce
using his system call fuzzer tool, and that looks like some kind of
locking ordering problem on the directory i_mutex chain. Our i_mutex
locking is rather complex, and depends on the topological ordering of
the directories, which is why we have been very wary of splicing
directory entries around.
Of course, we really don't want to ever see aliased unconnected
directories anyway, so none of this should ever happen, but this revert
aims to basically get us back to a known older state.
Bruce points to some of the previous discussion at
http://marc.info/?i=<
20110310105821.GE22723@ZenIV.linux.org.uk>
and in particular a long post from Neil:
http://marc.info/?i=<
20110311150749.
2fa2be66@notabene.brown>
It should be noted that it's possible that Dave's problems come from
other changes altohgether, including possibly just the fact that Dave
constantly is teachning his fuzzer new tricks. So what appears to be a
new bug could in fact be an old one that just gets newly triggered, but
reverting these patches as "still under heavy discussion" is the right
thing regardless.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 8 Jun 2012 16:26:55 +0000 (09:26 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi: Fix section mismatch warnings on 32-bit
x86/uv: Fix UV2 BAU legacy mode
x86/mm: Only add extra pages count for the first memory range during pre-allocation early page table space
x86, efi stub: Add .reloc section back into image
x86/ioapic: Fix NULL pointer dereference on CPU hotplug after disabling irqs
x86/reboot: Fix a warning message triggered by stop_other_cpus()
x86/intel/moorestown: Change intel_scu_devices_create() to __devinit
x86/numa: Set numa_nodes_parsed at acpi_numa_memory_affinity_init()
x86/gart: Fix kmemleak warning
x86: mce: Add the dropped timer interval init back
x86/mce: Fix the MCE poll timer logic
Linus Torvalds [Fri, 8 Jun 2012 16:14:46 +0000 (09:14 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A bit larger than what I'd wish for - half of it is due to hw driver
updates to Intel Ivy-Bridge which info got recently released,
cycles:pp should work there now too, amongst other things. (but we
are generally making exceptions for hardware enablement of this type.)
There are also callchain fixes in it - responding to mostly
theoretical (but valid) concerns. The tooling side sports perf.data
endianness/portability fixes which did not make it for the merge
window - and various other fixes as well."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
perf/x86: Check user address explicitly in copy_from_user_nmi()
perf/x86: Check if user fp is valid
perf: Limit callchains to 127
perf/x86: Allow multiple stacks
perf/x86: Update SNB PEBS constraints
perf/x86: Enable/Add IvyBridge hardware support
perf/x86: Implement cycles:p for SNB/IVB
perf/x86: Fix Intel shared extra MSR allocation
x86/decoder: Fix bsr/bsf/jmpe decoding with operand-size prefix
perf: Remove duplicate invocation on perf_event_for_each
perf uprobes: Remove unnecessary check before strlist__delete
perf symbols: Check for valid dso before creating map
perf evsel: Fix 32 bit values endianity swap for sample_id_all header
perf session: Handle endianity swap on sample_id_all header data
perf symbols: Handle different endians properly during symbol load
perf evlist: Pass third argument to ioctl explicitly
perf tools: Update ioctl documentation for PERF_IOC_FLAG_GROUP
perf tools: Make --version show kernel version instead of pull req tag
perf tools: Check if callchain is corrupted
perf callchain: Make callchain cursors TLS
...
Linus Torvalds [Fri, 8 Jun 2012 16:12:21 +0000 (09:12 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm intel and exynos fixes from Dave Airlie:
"A bunch of fixes for Intel and exynos, nothing too major, a new intel
PCI ID, and a fix for CRT detection."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: pch_irq_handler -> {ibx, cpt}_irq_handler
char/agp: add another Ironlake host bridge
drm/i915: fix up ivb plane 3 pageflips
drm/exynos: fixed blending for hdmi graphic layer
drm/exynos: Remove dummy encoder get_crtc operation implementation
drm/exynos: Keep a reference to frame buffer GEM objects
drm/exynos: Don't cast GEM object to Exynos GEM object when not needed
drm/exynos: DRIVER_BUS_PLATFORM is not a driver feature
drm/exynos: fixed size type.
drm/exynos: Use DRM_FORMAT_{NV12, YUV420} instead of DRM_FORMAT_{NV12M, YUV420M}
drm/i915: hold forcewake around ring hw init
drm/i915: Mark the ringbuffers as being in the GTT domain
drm/i915/crt: Do not rely upon the HPD presence pin
drm/i915: Reset last_retired_head when resetting ring
Linus Torvalds [Fri, 8 Jun 2012 16:11:33 +0000 (09:11 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull leap second timer fix from Thomas Gleixner.
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Fix CLOCK_MONOTONIC inconsistency during leapsecond
Linus Torvalds [Fri, 8 Jun 2012 16:10:35 +0000 (09:10 -0700)]
Merge tag 'moduleparam-for-linus' of git://git./linux/kernel/git/rusty/linux-2.6-for-linus
Pull minor module param fixes from Rusty Russell:
"One bugfix for multiple moduleparam levels, one removal of overzealous
printk."
* tag 'moduleparam-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
init: Drop initcall level output
module_param: stop double-calling parameters.
Don Zickus [Wed, 6 Jun 2012 14:05:42 +0000 (10:05 -0400)]
x86/nmi: Fix section mismatch warnings on 32-bit
It was reported that compiling for 32-bit caused a bunch of
section mismatch warnings:
VDSOSYM arch/x86/vdso/vdso32-syms.lds
LD arch/x86/vdso/built-in.o
LD arch/x86/built-in.o
WARNING: arch/x86/built-in.o(.data+0x5af0): Section mismatch in
reference from the variable test_nmi_ipi_callback_na.10451 to
the function .init.text:test_nmi_ipi_callback() [...]
WARNING: arch/x86/built-in.o(.data+0x5b04): Section mismatch in
reference from the variable nmi_unk_cb_na.10399 to the function
.init.text:nmi_unk_cb() The variable nmi_unk_cb_na.10399
references the function __init nmi_unk_cb() [...]
Both of these are attributed to the internal representation of
the nmiaction struct created during register_nmi_handler. The
reason for this is that those structs are not defined in the
init section whereas the rest of the code in nmi_selftest.c is.
To resolve this, I created a new #define,
register_nmi_handler_initonly, that tags the struct as
__initdata to resolve the mismatch. This #define should only be
used in rare situations where the register/unregister is called
during init of the kernel.
Big thanks to Jan Beulich for decoding this for me as I didn't
have a clue what was going on.
Reported-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Tested-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Cc: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/r/1338991542-23000-1-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Steffen Rumler [Wed, 6 Jun 2012 14:37:17 +0000 (16:37 +0200)]
powerpc: Fix kernel panic during kernel module load
This fixes a problem which can causes kernel oopses while loading
a kernel module.
According to the PowerPC EABI specification, GPR r11 is assigned
the dedicated function to point to the previous stack frame.
In the powerpc-specific kernel module loader, do_plt_call()
(in arch/powerpc/kernel/module_32.c), GPR r11 is also used
to generate trampoline code.
This combination crashes the kernel, in the case where the compiler
chooses to use a helper function for saving GPRs on entry, and the
module loader has placed the .init.text section far away from the
.text section, meaning that it has to generate a trampoline for
functions in the .init.text section to call the GPR save helper.
Because the trampoline trashes r11, references to the stack frame
using r11 can cause an oops.
The fix just uses GPR r12 instead of GPR r11 for generating the
trampoline code. According to the statements from Freescale, this is
safe from an EABI perspective.
I've tested the fix for kernel 2.6.33 on MPC8541.
Cc: stable@vger.kernel.org
Signed-off-by: Steffen Rumler <steffen.rumler.ext@nsn.com>
[paulus@samba.org: reworded the description]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cliff Wickman [Thu, 7 Jun 2012 13:31:40 +0000 (08:31 -0500)]
x86/uv: Fix UV2 BAU legacy mode
The SGI Altix UV2 BAU (Broadcast Assist Unit) as used for
tlb-shootdown (selective broadcast mode) always uses UV2
broadcast descriptor format. There is no need to clear the
'legacy' (UV1) mode, because the hardware always uses UV2 mode
for selective broadcast.
But the BIOS uses general broadcast and legacy mode, and the
hardware pays attention to the legacy mode bit for general
broadcast. So the kernel must not clear that mode bit.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/E1SccoO-0002Lh-Cb@eag09.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Yinghai Lu [Wed, 6 Jun 2012 17:55:40 +0000 (10:55 -0700)]
x86/mm: Only add extra pages count for the first memory range during pre-allocation early page table space
Robin found this regression:
| I just tried to boot an 8TB system. It fails very early in boot with:
| Kernel panic - not syncing: Cannot find space for the kernel page tables
git bisect commit
722bc6b16771ed80871e1fd81c86d3627dda2ac8.
A git revert of that commit does boot past that point on the 8TB
configuration.
That commit will add up extra pages for all memory range even
above 4g.
Try to limit that extra page count adding to first entry only.
Bisected-by: Robin Holt <holt@sgi.com>
Tested-by: Robin Holt <holt@sgi.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/CAE9FiQUj3wyzQxtq9yzBNc9u220p8JZ1FYHG7t%3DMOzJ%3D9BZMYA@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Fri, 8 Jun 2012 08:42:51 +0000 (09:42 +0100)]
Merge branch 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung into drm-fixes
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
drm/exynos: fixed blending for hdmi graphic layer
drm/exynos: Remove dummy encoder get_crtc operation implementation
drm/exynos: Keep a reference to frame buffer GEM objects
drm/exynos: Don't cast GEM object to Exynos GEM object when not needed
drm/exynos: DRIVER_BUS_PLATFORM is not a driver feature
drm/exynos: fixed size type.
drm/exynos: Use DRM_FORMAT_{NV12, YUV420} instead of DRM_FORMAT_{NV12M, YUV420M}
Dave Airlie [Fri, 8 Jun 2012 08:42:35 +0000 (09:42 +0100)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: pch_irq_handler -> {ibx, cpt}_irq_handler
char/agp: add another Ironlake host bridge
drm/i915: fix up ivb plane 3 pageflips
drm/i915: hold forcewake around ring hw init
drm/i915: Mark the ringbuffers as being in the GTT domain
drm/i915/crt: Do not rely upon the HPD presence pin
drm/i915: Reset last_retired_head when resetting ring
Borislav Petkov [Fri, 1 Jun 2012 16:56:00 +0000 (18:56 +0200)]
init: Drop initcall level output
9fb48c744ba6a ("params: add 3rd arg to option handler callback
signature") added similar lines to dmesg:
initlevel:0=early, 4 registered initcalls
initlevel:1=core, 31 registered initcalls
initlevel:2=postcore, 11 registered initcalls
initlevel:3=arch, 7 registered initcalls
initlevel:4=subsys, 40 registered initcalls
initlevel:5=fs, 30 registered initcalls
initlevel:6=device, 250 registered initcalls
initlevel:7=late, 35 registered initcalls
but they don't contain any info for the general user staring at dmesg.
I'm very doubtful the count of initcalls registered per level helps
anyone so drop that output completely.
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Fri, 8 Jun 2012 05:28:13 +0000 (14:58 +0930)]
module_param: stop double-calling parameters.
Commit
026cee0086fe1df4cf74691cf273062cc769617d "params:
<level>_initcall-like kernel parameters" set old-style module
parameters to level 0. And we call those level 0 calls where we used
to, early in start_kernel().
We also loop through the initcall levels and call the levelled
module_params before the corresponding initcall. Unfortunately level
0 is early_init(), so we call the standard module_param calls twice.
(Turns out most things don't care, but at least ubi.mtd does).
Change the level to -1 for standard module_param calls.
Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Paul Mackerras [Fri, 1 Jun 2012 08:13:43 +0000 (18:13 +1000)]
powerpc/time: Sanity check of decrementer expiration is necessary
This reverts
68568add2c ("powerpc/time: Remove unnecessary sanity check
of decrementer expiration"). We do need to check whether we have reached
the expiration time of the next event, because we sometimes get an early
decrementer interrupt, most notably when we set the decrementer to 1 in
arch_irq_work_raise(). The effect of not having the sanity check is that
if timer_interrupt() gets called early, we leave the decrementer set to
its maximum value, which means we then don't get any more decrementer
interrupts for about 4 seconds (or longer, depending on timebase
frequency). I saw these pauses as a consequence of getting a stray
hypervisor decrementer interrupt left over from exiting a KVM guest.
This isn't quite a straight revert because of changes to the surrounding
code, but it restores the same algorithm as was previously used.
Cc: stable@vger.kernel.org
Acked-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus Torvalds [Fri, 8 Jun 2012 00:54:07 +0000 (17:54 -0700)]
Revert "mm: correctly synchronize rss-counters at exit/exec"
This reverts commit
40af1bbdca47e5c8a2044039bb78ca8fd8b20f94.
It's horribly and utterly broken for at least the following reasons:
- calling sync_mm_rss() from mmput() is fundamentally wrong, because
there's absolutely no reason to believe that the task that does the
mmput() always does it on its own VM. Example: fork, ptrace, /proc -
you name it.
- calling it *after* having done mmdrop() on it is doubly insane, since
the mm struct may well be gone now.
- testing mm against NULL before you call it is insane too, since a
NULL mm there would have caused oopses long before.
.. and those are just the three bugs I found before I decided to give up
looking for me and revert it asap. I should have caught it before I
even took it, but I trusted Andrew too much.
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tao Ma [Thu, 7 Jun 2012 23:04:19 +0000 (19:04 -0400)]
ext4: don't set i_flags in EXT4_IOC_SETFLAGS
Commit
7990696 uses the ext4_{set,clear}_inode_flags() functions to
change the i_flags automatically but fails to remove the error setting
of i_flags. So we still have the problem of trashing state flags.
Fix this by removing the assignment.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Theodore Ts'o [Thu, 7 Jun 2012 22:56:06 +0000 (18:56 -0400)]
ext4: fix the free blocks calculation for ext3 file systems w/ uninit_bg
Ext3 filesystems that are converted to use as many ext4 file system
features as possible will enable uninit_bg to speed up e2fsck times.
These file systems will have a native ext3 layout of inode tables and
block allocation bitmaps (as opposed to ext4's flex_bg layout).
Unfortunately, in these cases, when first allocating a block in an
uninitialized block group, ext4 would incorrectly calculate the number
of free blocks in that block group, and then errorneously report that
the file system was corrupt:
EXT4-fs error (device vdd): ext4_mb_generate_buddy:741: group 30, 32254 clusters in bitmap, 32258 in gd
This problem can be reproduced via:
mke2fs -q -t ext4 -O ^flex_bg /dev/vdd 5g
mount -t ext4 /dev/vdd /mnt
fallocate -l 4600m /mnt/test
The problem was caused by a bone headed mistake in the check to see if a
particular metadata block was part of the block group.
Many thanks to Kees Cook for finding and bisecting the buggy commit
which introduced this bug (commit
fd034a84e1, present since v3.2).
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
Linus Torvalds [Thu, 7 Jun 2012 22:05:43 +0000 (15:05 -0700)]
Merge branch 'akpm' (Andrew's fixups)
Merge random fixes from Andrew Morton.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (11 patches)
mm: correctly synchronize rss-counters at exit/exec
btree: catch NULL value before it does harm
btree: fix tree corruption in btree_get_prev()
ipc: shm: restore MADV_REMOVE functionality on shared memory segments
drivers/platform/x86/acerhdf.c: correct Boris' mail address
c/r: prctl: drop VMA flags test on PR_SET_MM_ stack data assignment
c/r: prctl: add ability to get clear_tid_address
c/r: prctl: add minimal address test to PR_SET_MM
c/r: prctl: update prctl_set_mm_exe_file() after mm->num_exe_file_vmas removal
MAINTAINERS: whitespace fixes
shmem: replace_page must flush_dcache and others
Konstantin Khlebnikov [Thu, 7 Jun 2012 21:21:14 +0000 (14:21 -0700)]
mm: correctly synchronize rss-counters at exit/exec
mm->rss_stat counters have per-task delta: task->rss_stat. Before
changing task->mm pointer the kernel must flush this delta with
sync_mm_rss().
do_exit() already calls sync_mm_rss() to flush the rss-counters before
committing the rss statistics into task->signal->maxrss, taskstats,
audit and other stuff. Unfortunately the kernel does this before
calling mm_release(), which can call put_user() for processing
task->clear_child_tid. So at this point we can trigger page-faults and
task->rss_stat becomes non-zero again. As a result mm->rss_stat becomes
inconsistent and check_mm() will print something like this:
| BUG: Bad rss-counter state mm:
ffff88020813c380 idx:1 val:-1
| BUG: Bad rss-counter state mm:
ffff88020813c380 idx:2 val:1
This patch moves sync_mm_rss() into mm_release(), and moves mm_release()
out of do_exit() and calls it earlier. After mm_release() there should
be no pagefaults.
[akpm@linux-foundation.org: tweak comment]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org> [3.4.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joern Engel [Thu, 7 Jun 2012 21:21:14 +0000 (14:21 -0700)]
btree: catch NULL value before it does harm
Storing NULL values in the btree is illegal and can lead to memory
corruption and possible other fun as well. Catch it on insert, instead
of waiting for the inevitable.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland Dreier [Thu, 7 Jun 2012 21:21:13 +0000 (14:21 -0700)]
btree: fix tree corruption in btree_get_prev()
The memory the parameter __key points to is used as an iterator in
btree_get_prev(), so if we save off a bkey() pointer in retry_key and
then assign that to __key, we'll end up corrupting the btree internals
when we do eg
longcpy(__key, bkey(geo, node, i), geo->keylen);
to return the key value. What we should do instead is use longcpy() to
copy the key value that retry_key points to __key.
This can cause a btree to get corrupted by seemingly read-only
operations such as btree_for_each_safe.
[akpm@linux-foundation.org: avoid the double longcpy()]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Joern Engel <joern@logfs.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Thu, 7 Jun 2012 21:21:13 +0000 (14:21 -0700)]
ipc: shm: restore MADV_REMOVE functionality on shared memory segments
Commit
17cf28afea2a ("mm/fs: remove truncate_range") removed the
truncate_range inode operation in favour of the fallocate file
operation.
When using SYSV IPC shared memory segments, calling madvise with the
MADV_REMOVE advice on an area of shared memory will attempt to invoke
the .fallocate function for the shm_file_operations, which is NULL and
therefore returns -EOPNOTSUPP to userspace. The previous behaviour
would inherit the inode_operations from the underlying tmpfs file and
invoke truncate_range there.
This patch restores the previous behaviour by wrapping the underlying
fallocate function in shm_fallocate, as we do for fsync.
[hughd@google.com: use -ENOTSUPP in shm_fallocate()]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Borislav Petkov [Thu, 7 Jun 2012 21:21:12 +0000 (14:21 -0700)]
drivers/platform/x86/acerhdf.c: correct Boris' mail address
Correct mail address reference to a mail account which I actually read.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Cc: Peter Feuerer <peter@piie.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cyrill Gorcunov [Thu, 7 Jun 2012 21:21:12 +0000 (14:21 -0700)]
c/r: prctl: drop VMA flags test on PR_SET_MM_ stack data assignment
In commit
b76437579d13 ("procfs: mark thread stack correctly in
proc/<pid>/maps") the stack allocated via clone() is marked in
/proc/<pid>/maps as [stack:%d] thus it might be out of the former
mm->start_stack/end_stack values (and even has some custom VMA flags
set).
So to be able to restore mm->start_stack/end_stack drop vma flags test,
but still require the underlying VMA to exist.
As always note this feature is under CONFIG_CHECKPOINT_RESTORE and
requires CAP_SYS_RESOURCE to be granted.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cyrill Gorcunov [Thu, 7 Jun 2012 21:21:12 +0000 (14:21 -0700)]
c/r: prctl: add ability to get clear_tid_address
Zero is written at clear_tid_address when the process exits. This
functionality is used by pthread_join().
We already have sys_set_tid_address() to change this address for the
current task but there is no way to obtain it from user space.
Without the ability to find this address and dump it we can't restore
pthread'ed apps which call pthread_join() once they have been restored.
This patch introduces the PR_GET_TID_ADDRESS prctl option which allows
the current process to obtain own clear_tid_address.
This feature is available iif CONFIG_CHECKPOINT_RESTORE is set.
[akpm@linux-foundation.org: fix prctl numbering]
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pedro Alves <palves@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cyrill Gorcunov [Thu, 7 Jun 2012 21:21:11 +0000 (14:21 -0700)]
c/r: prctl: add minimal address test to PR_SET_MM
Make sure the address being set is greater than mmap_min_addr (as
suggested by Kees Cook).
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Konstantin Khlebnikov [Thu, 7 Jun 2012 21:21:11 +0000 (14:21 -0700)]
c/r: prctl: update prctl_set_mm_exe_file() after mm->num_exe_file_vmas removal
A fix for commit
b32dfe377102 ("c/r: prctl: add ability to set new
mm_struct::exe_file").
After removing mm->num_exe_file_vmas kernel keeps mm->exe_file until
final mmput(), it never becomes NULL while task is alive.
We can check for other mapped files in mm instead of checking
mm->num_exe_file_vmas, and mark mm with flag MMF_EXE_FILE_CHANGED in
order to forbid second changing of mm->exe_file.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Thu, 7 Jun 2012 21:21:10 +0000 (14:21 -0700)]
MAINTAINERS: whitespace fixes
Remove trailing spaces at EOL.
Always use a tab after the type :
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 7 Jun 2012 21:21:09 +0000 (14:21 -0700)]
shmem: replace_page must flush_dcache and others
Commit
bde05d1ccd51 ("shmem: replace page if mapping excludes its zone")
is not at all likely to break for anyone, but it was an earlier version
from before review feedback was incorporated. Fix that up now.
* shmem_replace_page must flush_dcache_page after copy_highpage [akpm]
* Expand comment on why shmem_unuse_inode needs page_swapcount [akpm]
* Remove excess of VM_BUG_ONs from shmem_replace_page [wangcong]
* Check page_private matches swap before calling shmem_replace_page [hughd]
* shmem_replace_page allow for unexpected race in radix_tree lookup [hughd]
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Stephane Marchesin <marcheu@chromium.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jordan Justen [Thu, 7 Jun 2012 16:05:21 +0000 (09:05 -0700)]
x86, efi stub: Add .reloc section back into image
Some UEFI firmware will not load a .efi with a .reloc section
with a size of 0.
Therefore, we create a .efi image with 4 main areas and 3 sections.
1. PE/COFF file header
2. .setup section (covers all setup code following the first sector)
3. .reloc section (contains 1 dummy reloc entry, created in build.c)
4. .text section (covers the remaining kernel image)
To make room for the new .setup section data, the header
bugger_off_msg had to be shortened.
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1339085121-12760-1-git-send-email-jordan.l.justen@intel.com
Tested-by: Lee G Rosenbaum <lee.g.rosenbaum@intel.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Linus Torvalds [Thu, 7 Jun 2012 16:06:54 +0000 (09:06 -0700)]
Merge tag 'parisc-fixes' of git://git./linux/kernel/git/jejb/parisc-2.6
Pull PARISC fixes from James Bottomley:
"This is a set of three bug fixes for minor build breakages that got
introduced just before 3.5-rc1 was released."
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix code to find libgcc
[PARISC] fix compile break in use of lib/strncopy_from_user.c
[PARISC] fix missing TAINT_WARN problem
Linus Torvalds [Thu, 7 Jun 2012 16:06:13 +0000 (09:06 -0700)]
Merge git://git./linux/kernel/git/cmetcalf/linux-tile
Pull tile fixes from Chris Metcalf:
"These two minor bug fixes fix build failures from some changes that
were merged in during the 3.5 merge window."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: add #include to unbreak build after generic init_task conversion
tile: remove cpu_idle_on_new_stack
Artem Bityutskiy [Thu, 7 Jun 2012 12:15:30 +0000 (15:15 +0300)]
UBI: correct ubi_wl_flush locking
Commit "
62f38455 UBI: modify ubi_wl_flush function to clear work queue for a lnum"
takes the 'work_sem' semaphore in write mode for the entire loop, which is not
very good because it will block other workers for potentially long time. We do
not need to have it in write mode - read mode is enough, and we do not need to
hole it over the entire loop. So this patch turns changes the locking: takes
'work_sem' in read mode and pushes it down to the loop.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Artem Bityutskiy [Wed, 6 Jun 2012 13:03:10 +0000 (16:03 +0300)]
UBIFS: fix debugfs-less systems support
Commit "
f70b7e5 UBIFS: remove Kconfig debugging option" broke UBIFS and it
refuses to initialize if debugfs (CONFIG_DEBUG_FS) is disabled. I incorrectly
assumed that debugfs files creation function will return success if debugfs
is disabled, but they actually return -ENODEV. This patch fixes the issue.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Artem Bityutskiy [Wed, 6 Jun 2012 12:22:41 +0000 (15:22 +0300)]
UBI: fix debugfs-less systems support
Commit "
aa44d1d UBI: remove Kconfig debugging option" broke UBI and it
refuses to initialize if debugfs (CONFIG_DEBUG_FS) is disabled. I incorrectly
assumed that debugfs files creation function will return success if debugfs
is disabled, but they actually return -ENODEV. This patch fixes the issue.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Adam Jackson [Wed, 6 Jun 2012 19:45:44 +0000 (15:45 -0400)]
drm/i915: pch_irq_handler -> {ibx, cpt}_irq_handler
Cougar/Panther Point redefine the bits in SDEIIR pretty completely.
This function is just debugging, but if we're debugging we probably want
to be told accurate things instead of lies.
I'm told Lynx Point changes this yet more, but I have no idea how...
Note from Eugeni's review:
"For the record and for future enabling efforts, for LPT, bits 28-31
and 1-14 are gone since CPT/PPT (e.g., those must be zero). And there
is the bit 15 as a new addition, but we are not using it yet and
probably won't be using in foreseeable future."
Signed-off-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35103
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Wed, 6 Jun 2012 18:56:45 +0000 (11:56 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Update e-mail address in MAINTAINERS"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
MAINTAINERS: Update my e-mail address
Linus Torvalds [Wed, 6 Jun 2012 17:47:15 +0000 (10:47 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux
Pull ACPI and Power Management changes from Len Brown.
This does an evil merge to fix up what I think is a mismerge by Len to
the gma500 driver, and restore it to the mainline state.
In that driver, both branches had commented out the call to
acpi_video_register(), and Len resolved the merge to that commented-out
version.
However, in mainline, further changes by Alan (commit
d839ede47a56:
"gma500: opregion and ACPI" to be exact) had re-enabled the ACPI video
registration, so the current state of the driver seems to want it.
Alan is apparently still feeling the effects of partying with the Queen,
so he didn't reply to my query, but I'll do the evil merge anyway.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
ACPI: fix acpi_bus.h build warnings when ACPI is not enabled
drivers: acpi: Fix dependency for ACPI_HOTPLUG_CPU
tools/power turbostat: fix IVB support
tools/power turbostat: fix un-intended affinity of forked program
ACPI video: use after input_unregister_device()
gma500: don't register the ACPI video bus
acpi_video: Intel video is not always i915
acpi_video: fix leaking PCI references
ACPI: Ignore invalid _PSS entries, but use valid ones
ACPI battery: only refresh the sysfs files when pertinent information changes
Linus Torvalds [Wed, 6 Jun 2012 17:45:21 +0000 (10:45 -0700)]
Merge tag 'rdma-fixes' of git://git./linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA fixes from Roland Dreier:
"All in hardware drivers:
- Fix crash in cxgb4
- Fixes to new ocrdma driver
- Regression fixes for mlx4"
* tag 'rdma-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix max_wqe capacity reported from query device
mlx4_core: Fix setting VL_cap in mlx4_SET_PORT wrapper flow
IB/mlx4: Fix EQ deallocation in legacy mode
RDMA/cxgb4: Fix crash when peer address is 0.0.0.0
RDMA/ocrdma: Remove unnecessary version.h includes
RDMA/ocrdma: Fix signaled event for SRQ_LIMIT_REACHED
RDMA/ocrdma: Correct queue free count math
Roland Dreier [Wed, 6 Jun 2012 17:08:11 +0000 (10:08 -0700)]
Merge branches 'cxgb4', 'mlx4' and 'ocrdma' into for-linus
Sagi Grimberg [Thu, 24 May 2012 13:08:08 +0000 (16:08 +0300)]
IB/mlx4: Fix max_wqe capacity reported from query device
1. Limit the max number of WQEs per QP reported when querying the
device, so that ib_create_qp() will not fail for a QP size that the
device claimed to support due to additional headroom WQEs being
allocated.
2. Limit qp resources accepted for ib_create_qp() to the limits
reported in ib_query_device(). In kernel space, make sure that the
limits returned to the caller following qp creation also lie within
the reported device limits. For userspace, report as before, and do
adjustment in libmlx4 (so as not to break ABI).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Sagi Grimberg <sagig@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Jack Morgenstein [Thu, 24 May 2012 13:08:09 +0000 (16:08 +0300)]
mlx4_core: Fix setting VL_cap in mlx4_SET_PORT wrapper flow
Commit
096335b3f983 ("mlx4_core: Allow dynamic MTU configuration for
IB ports") modifies the port VL setting. This exposes a bug in
mlx4_common_set_port(), where the VL cap value passed in (inside the
command mailbox) is incorrectly zeroed-out:
mlx4_SET_PORT modifies the VL_cap field (byte 3 of the mailbox).
Since the SET_PORT command is paravirtualized on the master as well as
on the slaves, mlx4_SET_PORT_wrapper() is invoked on the master. This
calls mlx4_common_set_port() where mailbox byte 3 gets overwritten by
code which should only set a single bit in that byte (for the reset
qkey counter flag) -- but instead overwrites the entire byte.
The result is that when running in SR-IOV mode, the VL_cap will be set
to zero -- fix this.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Linus Torvalds [Wed, 6 Jun 2012 16:49:28 +0000 (09:49 -0700)]
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull two md fixes from NeilBrown:
"One sparse-warning fix, one bugfix for 3.4-stable"
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md: raid1/raid10: fix problem with merge_bvec_fn
lib/raid6: fix sparse warnings in recovery functions
Linus Torvalds [Wed, 6 Jun 2012 16:47:57 +0000 (09:47 -0700)]
Merge tag 'iommu-fixes-3.5-rc1' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Two patches are in here which fix AMD IOMMU specific issues. One
patch fixes a long-standing warning on resume because the
amd_iommu_resume function enabled interrupts. The other patch fixes a
deadlock in an error-path of the page-fault request handling code of
the IOMMU driver.
* tag 'iommu-fixes-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix deadlock in ppr-handling error path
iommu/amd: Cache pdev pointer to root-bridge
Chris Metcalf [Wed, 6 Jun 2012 15:23:19 +0000 (11:23 -0400)]
tile: add #include to unbreak build after generic init_task conversion
Some code was moved from init_task.c to setup.c but the appropriate
header needed to be moved as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Chris Metcalf [Wed, 6 Jun 2012 15:21:44 +0000 (11:21 -0400)]
tile: remove cpu_idle_on_new_stack
This routine isn't used unless CONFIG_HOMECACHE is enabled, which
isn't even available as a public configuration option yet.
Since it no longer links correctly in 3.4, just remove it for now.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>