OSDN Git Service
Filipe Manana [Fri, 11 Nov 2022 11:50:30 +0000 (11:50 +0000)]
btrfs: search for delalloc more efficiently during lseek/fiemap
During lseek (SEEK_HOLE/DATA) and fiemap, when processing a file range
that corresponds to a hole or a prealloc extent, we have to check if
there's any delalloc in the range. We do it by searching for delalloc
ranges in the inode's io_tree (for unflushed delalloc) and in the inode's
extent map tree (for delalloc that is flushing).
We avoid searching the extent map tree if the number of outstanding
extents is 0, as in that case we can't have extent maps for our search
range in the tree that correspond to delalloc that is flushing. However
if we have any unflushed delalloc, due to buffered writes or mmap writes,
then the outstanding extents counter is not 0 and we'll search the extent
map tree. The tree may be large because it can have lots of extent maps
that were loaded by reads or created by previous writes, therefore taking
a significant time to search the tree, specially if have a file with a
lot of holes and/or prealloc extents.
We can improve on this by instead of searching the extent map tree,
searching the ordered extents tree of the inode, since when delalloc is
flushing we create an ordered extent along with the new extent map, while
holding the respective file range locked in the inode's io_tree. The
ordered extents tree is typically much smaller, since ordered extents have
a short life and get removed from the tree once they are completed, while
extent maps can stay for a very long time in the extent map tree, either
created by previous writes or loaded by read operations.
So use the ordered extents tree instead of the extent maps tree.
This change is part of a patchset that has the goal to make performance
better for applications that use lseek's SEEK_HOLE and SEEK_DATA modes to
iterate over the extents of a file. Two examples are the cp program from
coreutils 9.0+ and the tar program (when using its --sparse / -S option).
A sample test and results are listed in the changelog of the last patch
in the series:
1/9 btrfs: remove leftover setting of EXTENT_UPTODATE state in an inode's io_tree
2/9 btrfs: add an early exit when searching for delalloc range for lseek/fiemap
3/9 btrfs: skip unnecessary delalloc searches during lseek/fiemap
4/9 btrfs: search for delalloc more efficiently during lseek/fiemap
5/9 btrfs: remove no longer used btrfs_next_extent_map()
6/9 btrfs: allow passing a cached state record to count_range_bits()
7/9 btrfs: update stale comment for count_range_bits()
8/9 btrfs: use cached state when looking for delalloc ranges with fiemap
9/9 btrfs: use cached state when looking for delalloc ranges with lseek
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Link: https://lore.kernel.org/linux-btrfs/20221106073028.71F9.409509F4@e16-tech.com/
Link: https://lore.kernel.org/linux-btrfs/CAL3q7H5NSVicm7nYBJ7x8fFkDpno8z3PYt5aPU43Bajc1H0h1Q@mail.gmail.com/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Fri, 11 Nov 2022 11:50:29 +0000 (11:50 +0000)]
btrfs: skip unnecessary delalloc searches during lseek/fiemap
During lseek (SEEK_HOLE/DATA) and fiemap, when processing a file range
that corresponds to a hole or a prealloc extent, if we find that there is
no delalloc marked in the inode's io_tree but there is delalloc due to
an extent map in the io tree, then on the next iteration that calls
find_delalloc_subrange() we can skip searching the io tree again, since
on the first call we had no delalloc in the io tree for the whole range.
This change is part of a patchset that has the goal to make performance
better for applications that use lseek's SEEK_HOLE and SEEK_DATA modes to
iterate over the extents of a file. Two examples are the cp program from
coreutils 9.0+ and the tar program (when using its --sparse / -S option).
A sample test and results are listed in the changelog of the last patch
in the series:
1/9 btrfs: remove leftover setting of EXTENT_UPTODATE state in an inode's io_tree
2/9 btrfs: add an early exit when searching for delalloc range for lseek/fiemap
3/9 btrfs: skip unnecessary delalloc searches during lseek/fiemap
4/9 btrfs: search for delalloc more efficiently during lseek/fiemap
5/9 btrfs: remove no longer used btrfs_next_extent_map()
6/9 btrfs: allow passing a cached state record to count_range_bits()
7/9 btrfs: update stale comment for count_range_bits()
8/9 btrfs: use cached state when looking for delalloc ranges with fiemap
9/9 btrfs: use cached state when looking for delalloc ranges with lseek
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Link: https://lore.kernel.org/linux-btrfs/20221106073028.71F9.409509F4@e16-tech.com/
Link: https://lore.kernel.org/linux-btrfs/CAL3q7H5NSVicm7nYBJ7x8fFkDpno8z3PYt5aPU43Bajc1H0h1Q@mail.gmail.com/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Fri, 11 Nov 2022 11:50:28 +0000 (11:50 +0000)]
btrfs: add an early exit when searching for delalloc range for lseek/fiemap
During fiemap and lseek (SEEK_HOLE/DATA), when looking for delalloc in a
range corresponding to a hole or a prealloc extent, if we found the whole
range marked as delalloc in the inode's io_tree, then we can terminate
immediately and avoid searching the extent map tree. If not, and if the
found delalloc starts at the same offset of our search start but ends
before our search range's end, then we can adjust the search range for
the search in the extent map tree. So implement those changes.
This change is part of a patchset that has the goal to make performance
better for applications that use lseek's SEEK_HOLE and SEEK_DATA modes to
iterate over the extents of a file. Two examples are the cp program from
coreutils 9.0+ and the tar program (when using its --sparse / -S option).
A sample test and results are listed in the changelog of the last patch
in the series:
1/9 btrfs: remove leftover setting of EXTENT_UPTODATE state in an inode's io_tree
2/9 btrfs: add an early exit when searching for delalloc range for lseek/fiemap
3/9 btrfs: skip unnecessary delalloc searches during lseek/fiemap
4/9 btrfs: search for delalloc more efficiently during lseek/fiemap
5/9 btrfs: remove no longer used btrfs_next_extent_map()
6/9 btrfs: allow passing a cached state record to count_range_bits()
7/9 btrfs: update stale comment for count_range_bits()
8/9 btrfs: use cached state when looking for delalloc ranges with fiemap
9/9 btrfs: use cached state when looking for delalloc ranges with lseek
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Link: https://lore.kernel.org/linux-btrfs/20221106073028.71F9.409509F4@e16-tech.com/
Link: https://lore.kernel.org/linux-btrfs/CAL3q7H5NSVicm7nYBJ7x8fFkDpno8z3PYt5aPU43Bajc1H0h1Q@mail.gmail.com/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Fri, 11 Nov 2022 11:50:27 +0000 (11:50 +0000)]
btrfs: remove leftover setting of EXTENT_UPTODATE state in an inode's io_tree
We don't need to set the EXTENT_UPDATE bit in an inode's io_tree to mark a
range as uptodate, we rely on the pages themselves being uptodate - page
reading is not triggered for already uptodate pages. Recently we removed
most use of the EXTENT_UPTODATE for buffered IO with commit
52b029f42751
("btrfs: remove unnecessary EXTENT_UPTODATE state in buffered I/O path"),
but there were a few leftovers, namely when reading from holes and
successfully finishing read repair.
These leftovers are unnecessarily making an inode's tree larger and deeper,
slowing down searches on it. So remove all the leftovers.
This change is part of a patchset that has the goal to make performance
better for applications that use lseek's SEEK_HOLE and SEEK_DATA modes to
iterate over the extents of a file. Two examples are the cp program from
coreutils 9.0+ and the tar program (when using its --sparse / -S option).
A sample test and results are listed in the changelog of the last patch
in the series:
1/9 btrfs: remove leftover setting of EXTENT_UPTODATE state in an inode's io_tree
2/9 btrfs: add an early exit when searching for delalloc range for lseek/fiemap
3/9 btrfs: skip unnecessary delalloc searches during lseek/fiemap
4/9 btrfs: search for delalloc more efficiently during lseek/fiemap
5/9 btrfs: remove no longer used btrfs_next_extent_map()
6/9 btrfs: allow passing a cached state record to count_range_bits()
7/9 btrfs: update stale comment for count_range_bits()
8/9 btrfs: use cached state when looking for delalloc ranges with fiemap
9/9 btrfs: use cached state when looking for delalloc ranges with lseek
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Link: https://lore.kernel.org/linux-btrfs/20221106073028.71F9.409509F4@e16-tech.com/
Link: https://lore.kernel.org/linux-btrfs/CAL3q7H5NSVicm7nYBJ7x8fFkDpno8z3PYt5aPU43Bajc1H0h1Q@mail.gmail.com/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Wed, 14 Sep 2022 05:32:51 +0000 (13:32 +0800)]
btrfs: move tree block parentness check into validate_extent_buffer()
[BACKGROUND]
Although both btrfs metadata and data has their read time verification
done at endio time (btrfs_validate_metadata_buffer() and
btrfs_verify_data_csum()), metadata has extra verification, mostly
parentness check including first key/transid/owner_root/level, done at
read_tree_block() and btrfs_read_extent_buffer().
On the other hand, all the data verification is done at endio context.
[ENHANCEMENT]
This patch will make a new union in btrfs_bio, taking the space of the
old data checksums, thus it will not increase the memory usage.
With that extra btrfs_tree_parent_check inside btrfs_bio, we can just
pass the check parameter into read_extent_buffer_pages(), and before
submitting the bio, we can copy the check structure into btrfs_bio.
And finally at endio time, we can grab btrfs_bio::parent_check and pass
it to validate_extent_buffer(), to move the remaining checks into it.
This brings the following benefits:
- Much simpler btrfs_read_extent_buffer()
Now it only needs to iterate through all mirrors.
- Simpler read-time transid check
Previously we go verify_parent_transid() after reading out the extent
buffer.
Now the transid check is done inside the endio function, no other
code can modify the content.
Thus no need to use the extent lock anymore.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Wed, 14 Sep 2022 05:32:50 +0000 (13:32 +0800)]
btrfs: concentrate all tree block parentness check parameters into one structure
There are several different tree block parentness check parameters used
across several helpers:
- level
Mandatory
- transid
Under most cases it's mandatory, but there are several backref cases
which skips this check.
- owner_root
- first_key
Utilized by most top-down tree search routine. Otherwise can be
skipped.
Those four members are not always mandatory checks, and some of them are
the same u64, which means if some arguments got swapped compiler will
not catch it.
Furthermore if we're going to further expand the parentness check, we
need to modify quite some helpers just to add one more parameter.
This patch will concentrate all these members into a structure called
btrfs_tree_parent_check, and pass that structure for the following
helpers:
- btrfs_read_extent_buffer()
- read_tree_block()
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Anand Jain [Mon, 7 Nov 2022 15:07:17 +0000 (23:07 +0800)]
btrfs: move device->name RCU allocation and assign to btrfs_alloc_device()
There is a repeating code section in the parent function after calling
btrfs_alloc_device(), as below:
name = rcu_string_strdup(path, GFP_...);
if (!name) {
btrfs_free_device(device);
return ERR_PTR(-ENOMEM);
}
rcu_assign_pointer(device->name, name);
Except in add_missing_dev() for obvious reasons.
This patch consolidates that repeating code into the btrfs_alloc_device()
itself so that the parent function doesn't have to duplicate code.
This consolidation also helps to review issues regarding RCU lock
violation with device->name.
Parent function device_list_add() and add_missing_dev() use GFP_NOFS for
the allocation, whereas the rest of the parent functions use GFP_KERNEL,
so bring the NOFS allocation context using memalloc_nofs_save() in the
function device_list_add() and add_missing_dev() is already doing it.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 7 Nov 2022 16:30:21 +0000 (17:30 +0100)]
btrfs: constify input buffer parameter in compression code
The input buffers passed down to compression must never be changed,
switch type to u8 as it's a raw byte buffer and use const.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 7 Nov 2022 07:32:31 +0000 (15:32 +0800)]
btrfs: raid56: remove the old error tracking system
Since all the recovery paths have been migrated to the new error bitmap
based system, we can remove the old stripe number based system.
This cleanup involves one behavior change:
- Rebuild rbio can no longer be merged
Previously a rebuild rbio (caused by retry after data csum mismatch)
can be merged, if the error happens in the same stripe.
But with the new error bitmap based solution, it's much harder to
compare error bitmaps.
So here we just don't merge rebuild rbio at all.
This may introduce some performance impact at extreme corner cases,
but we're willing to take it.
Other than that, this patch will cleanup the following members:
- rbio::faila
- rbio::failb
They will be replaced by per-vertical stripe check, which is more
accurate.
- rbio::error
It will be replace by per-vertical stripe error bitmap check.
- Allow get_rbio_vertical_errors() to accept NULL pointers for
@faila and @failb
Some call sites only want to check if we have errors beyond the
tolerance.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 7 Nov 2022 07:32:30 +0000 (15:32 +0800)]
btrfs: raid56: migrate recovery and scrub recovery path to use error_bitmap
Since we have rbio::error_bitmap to indicate exactly where the errors
are (including read error and csum mismatch error), we can make recovery
path more accurate.
For example:
0 32K 64K
Data 1 |XXXXXXXX| |
Data 2 | |XXXXXXXXX|
Parity | | |
1) Get csum mismatch when reading data 1 [0, 32K)
2) Mark corresponding range error
The old code will mark the whole data 1 stripe as error.
While the new code will only mark data 1 [0, 32K) as error.
3) Recovery path
The old code will recover data 1 [0, 64K), all using Data 2 and
parity.
This means, Data 1 [32K, 64K) will be corrupted data, as data 2
[32K, 64K) is already corrupted.
While the new code will only recover data 1 [0, 32K), as only
that range has error so far.
This new behavior can avoid populating rbio cache with incorrect data.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Mon, 7 Nov 2022 07:32:29 +0000 (15:32 +0800)]
btrfs: raid56: introduce btrfs_raid_bio::error_bitmap
Currently btrfs raid56 uses btrfs_raid_bio::faila and failb to indicate
which stripe(s) had IO errors.
But that has some problems:
- If one sector failed csum check, the whole stripe where the corruption
is will be marked error.
This can reduce the chance we do recover, like this:
0 4K 8K
Data 1 |XX| |
Data 2 | |XX|
Parity | | |
In above case, 0~4K in data 1 should be recovered using data 2 and
parity, while 4K~8K in data 2 should be recovered using data 1 and
parity.
Currently if we trigger read on 0~4K of data 1, we will also recover
4K~8K of data 1 using corrupted data 2 and parity, causing wrong
result in rbio cache.
- Harder to expand for future M-N scheme
As we're limited to just faila/b, two corruptions.
- Harder to expand to handle extra csum errors
This can be problematic if we start to do csum verification.
This patch will introduce an extra @error_bitmap, where one bit
represents error that happened for that sector.
The choice to introduce a new error bitmap other than reusing
sector_ptr, is to avoid extra search between rbio::stripe_sectors[] and
rbio::bio_sectors[].
Since we can submit bio using sectors from both sectors, doing proper
search on both array will more complex.
Although the new bitmap will take extra memory, later we can remove
things like @error and faila/b to save some memory.
Currently the new error bitmap and failab mechanism coexists, the error
bitmap is only updated at endio time and recover entrance.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 28 Oct 2022 01:53:04 +0000 (03:53 +0200)]
btrfs: pass btrfs_inode to btrfs_add_delayed_iput
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 28 Oct 2022 01:47:16 +0000 (03:47 +0200)]
btrfs: use btrfs_inode inside btrfs_verify_data_csum
The function is mostly using internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 28 Oct 2022 01:47:16 +0000 (03:47 +0200)]
btrfs: use btrfs_inode inside compress_file_range
The function is mostly using internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 28 Oct 2022 01:37:50 +0000 (03:37 +0200)]
btrfs: switch async_chunk::inode to btrfs_inode
The async_chunk::inode structure is for internal interfaces so we should
use the btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_inherit_iflags
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to inode_tree_add
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to fixup_tree_root_location
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_inode_by_name
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_unlink_subvol
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_clear_delalloc_extent
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_split_delalloc_extent
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_set_delalloc_extent
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_merge_delalloc_extent
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 28 Oct 2022 00:55:51 +0000 (02:55 +0200)]
btrfs: switch extent_io_tree::private_data to btrfs_inode and rename
The extent_io_tree::private_data was meant to be a preparatory work for
the metadata inode rework but that never materialized. Now it's used
only for an inode so it's better to change the appropriate type and
rename it.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 28 Oct 2022 00:47:06 +0000 (02:47 +0200)]
btrfs: drop private_data parameter from extent_io_tree_init
All callers except one pass NULL, so the parameter can be dropped and
the inode::io_tree initialization can be open coded.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_delete_subvolume
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to __unlink_start_trans
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_check_data_csum
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Fri, 28 Oct 2022 00:22:15 +0000 (02:22 +0200)]
btrfs: switch btrfs_writepage_fixup::inode to btrfs_inode
The btrfs_writepage_fixup structure is for internal interfaces so we
should use the btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_add_delalloc_inodes
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_dirty_inode
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_inode_unlock
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_inode_lock
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_truncate
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_submit_dio_bio
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: switch btrfs_dio_private::inode to btrfs_inode
The btrfs_dio_private structure is for internal interfaces so we should
use the btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_repair_one_sector
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to submit_one_bio
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_submit_dio_repair_bio
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_submit_data_read_bio
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_submit_data_write_bio
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_submit_metadata_bio
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_wq_submit_bio
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_submit_bio_start_direct_io
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:41:32 +0000 (02:41 +0200)]
btrfs: pass btrfs_inode to btrfs_submit_bio_start
The function is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:40:36 +0000 (02:40 +0200)]
btrfs: switch async_submit_bio::inode to btrfs_inode
The async bio submit is for internal interfaces so we should use the
btrfs_inode.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:30:45 +0000 (02:30 +0200)]
btrfs: simplify btree_submit_bio_start and btrfs_submit_bio_start parameters
After previous patches the unused parameters can be removed from
btree_submit_bio_start and btrfs_submit_bio_start as they don't need to
conform to the extent_submit_bio_start_t typedef.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:22:19 +0000 (02:22 +0200)]
btrfs: change how submit bio callback is passed to btrfs_wq_submit_bio
There's a callback function parameter for btrfs_wq_submit_bio that can
be one of: metadata, buffered data, direct io data. The callback
abstraction is unnecessary as we have all functions available.
Replace the parameter with a command that leads to a direct call in
run_one_async_start. The called functions can be then simplified and we
can also remove the extent_submit_bio_start_t typedef.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:07:10 +0000 (02:07 +0200)]
btrfs: drop parameter compression_type from btrfs_submit_dio_repair_bio
Compression and direct io don't work together so the compression
parameter can be dropped after previous patch that changed the call
to direct.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 00:02:32 +0000 (02:02 +0200)]
btrfs: change how repair action is passed to btrfs_repair_one_sector
There's a function pointer passed to btrfs_repair_one_sector that will
submit the right bio for repair. However there are only two callbacks,
for buffered and for direct IO. This can be simplified to a bool-based
switch and call either function, indirect calls in this case is an
unnecessary abstraction. This allows to remove the submit_bio_hook_t
typedef.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 31 Oct 2022 19:33:46 +0000 (20:33 +0100)]
btrfs: convert btrfs_block_group::seq_zone to runtime flag
In zoned mode the sequential status of zone can be also tracked in the
runtime flags of block group.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 31 Oct 2022 19:33:44 +0000 (20:33 +0100)]
btrfs: convert btrfs_block_group::needs_free_space to runtime flag
We already have flags in block group to track various status bits,
convert needs_free_space as well and reduce size of btrfs_block_group.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 31 Oct 2022 19:33:42 +0000 (20:33 +0100)]
btrfs: zoned: use helper to check a power of two zone size
We have a 64bit compatible helper to check if a value is a power of two,
use it instead of open coding it.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Mon, 31 Oct 2022 19:33:40 +0000 (20:33 +0100)]
btrfs: zlib: use copy_page for full page copy
The copy_page helper may use an optimized version for full page copy
(eg. on s390 there's a special instruction for that), there's one more
left to convert.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:54 +0000 (16:15 +0000)]
btrfs: send: bump the extent reference count limit for backref walking
After the previous patchset which is comprised of the following patches:
01/17 btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
02/17 btrfs: fix inode list leak during backref walking at find_parent_nodes()
03/17 btrfs: fix ulist leaks in error paths of qgroup self tests
04/17 btrfs: remove pointless and double ulist frees in error paths of qgroup tests
05/17 btrfs: send: avoid unnecessary path allocations when finding extent clone
06/17 btrfs: send: update comment at find_extent_clone()
07/17 btrfs: send: drop unnecessary backref context field initializations
08/17 btrfs: send: avoid unnecessary backref lookups when finding clone source
09/17 btrfs: send: optimize clone detection to increase extent sharing
10/17 btrfs: use a single argument for extent offset in backref walking functions
11/17 btrfs: use a structure to pass arguments to backref walking functions
12/17 btrfs: reuse roots ulist on each leaf iteration for iterate_extent_inodes()
13/17 btrfs: constify ulist parameter of ulist_next()
14/17 btrfs: send: cache leaf to roots mapping during backref walking
15/17 btrfs: send: skip unnecessary backref iterations
16/17 btrfs: send: avoid double extent tree search when finding clone source
17/17 btrfs: send: skip resolution of our own backref when finding clone source
we have now much better performance when doing backref walking in the send
code, so we can increase the current limit from 64 to 1024 references.
This limit is still a bit conservative because there are still edge cases
where backref walking will be too slow and spend a lot of cpu time, some IO
reading b+tree nodes/leaves and memory. The goal is to eventually get rid
of any limit, but for now bump it as it benefits users with extents shared
more than 64 times and up to 1024 times, allowing for more deduplication
at the destination without having to run a dedupe tool after a receive.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:53 +0000 (16:15 +0000)]
btrfs: send: skip resolution of our own backref when finding clone source
When doing backref walking to determine a source range to clone from, it
is worthless to collect and resolve our own data backref, as we can't
obviously use it as a clone source and it represents the range we want to
clone into. Collecting the backref implies doing the extra work to resolve
it, doing the search for a file extent item in a subvolume tree, etc.
Skipping the data backref is valid as long as we only have the send root
as the single clone root, otherwise the leaf with the file extent item may
be accessible from another clone root due to shared subtrees created by
snapshots, and therefore we have to collect the backref and resolve it.
So add a callback to the backref walking code to guide it to skip data
backrefs.
This change is part of a patchset comprised of the following patches:
01/17 btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
02/17 btrfs: fix inode list leak during backref walking at find_parent_nodes()
03/17 btrfs: fix ulist leaks in error paths of qgroup self tests
04/17 btrfs: remove pointless and double ulist frees in error paths of qgroup tests
05/17 btrfs: send: avoid unnecessary path allocations when finding extent clone
06/17 btrfs: send: update comment at find_extent_clone()
07/17 btrfs: send: drop unnecessary backref context field initializations
08/17 btrfs: send: avoid unnecessary backref lookups when finding clone source
09/17 btrfs: send: optimize clone detection to increase extent sharing
10/17 btrfs: use a single argument for extent offset in backref walking functions
11/17 btrfs: use a structure to pass arguments to backref walking functions
12/17 btrfs: reuse roots ulist on each leaf iteration for iterate_extent_inodes()
13/17 btrfs: constify ulist parameter of ulist_next()
14/17 btrfs: send: cache leaf to roots mapping during backref walking
15/17 btrfs: send: skip unnecessary backref iterations
16/17 btrfs: send: avoid double extent tree search when finding clone source
17/17 btrfs: send: skip resolution of our own backref when finding clone source
The following test was run on non-debug kernel (Debian's default kernel
config) before and after applying the patchset:
$ cat test-send-many-shared-extents.sh
#!/bin/bash
DEV=/dev/sdh
MNT=/mnt/sdh
umount $DEV &> /dev/null
mkfs.btrfs -f $DEV
mount $DEV $MNT
num_files=50000
num_clones_per_file=50
for ((i = 1; i <= $num_files; i++)); do
xfs_io -f -c "pwrite 0 64K" $MNT/file_$i > /dev/null
echo -ne "\r$i files created..."
done
echo
btrfs subvolume snapshot -r $MNT $MNT/snap1
cloned=0
for ((i = 1; i <= $num_clones_per_file; i++)); do
for ((j = 1; j <= $num_files; j++)); do
cp --reflink=always $MNT/file_$j $MNT/file_${j}_clone_${i}
cloned=$((cloned + 1))
echo -ne "\r$cloned / $((num_files * num_clones_per_file)) clone operations"
done
done
echo
btrfs subvolume snapshot -r $MNT $MNT/snap2
# Unmount and mount again to clear all cached metadata (and data).
umount $DEV
mount $DEV $MNT
start=$(date +%s%N)
btrfs send $MNT/snap2 > /dev/null
end=$(date +%s%N)
dur=$(( (end - start) /
1000000000 ))
echo -e "\nFull send took $dur seconds"
# Unmount and mount again to clear all cached metadata (and data).
umount $DEV
mount $DEV $MNT
start=$(date +%s%N)
btrfs send -p $MNT/snap1 $MNT/snap2 > /dev/null
end=$(date +%s%N)
dur=$(( (end - start) /
1000000000 ))
echo -e "\nIncremental send took $dur seconds"
umount $MNT
Before applying the patchset:
(...)
Full send took 1108 seconds
(...)
Incremental send took 1135 seconds
After applying the whole patchset:
(...)
Full send took 268 seconds (-75.8%)
(...)
Incremental send took 316 seconds (-72.2%)
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:52 +0000 (16:15 +0000)]
btrfs: send: avoid double extent tree search when finding clone source
At find_extent_clone() we search twice for the extent item corresponding
to the data extent that the current file extent items points to:
1) Once with a call to extent_from_logical();
2) Once again during backref walking, through iterate_extent_inodes()
which eventually leads to find_parent_nodes() where we will search
again the extent tree for the same extent item.
The extent tree can be huge, so doing this one extra search for every
extent we want to send adds up and it's expensive.
The first call is there since the send code was introduced and it
accomplishes two things:
1) Check that the extent is flagged as a data extent in the extent tree.
But it can not be anything else, otherwise we wouldn't have a file
extent item in the send root pointing to it.
This was probably added to catch bugs in the early days where send was
yet too young and the interaction with everything else was far from
perfect;
2) Check how many direct references there are on the extent, and if
there's too many (more than SEND_MAX_EXTENT_REFS), avoid doing the
backred walking as it may take too long and slowdown send.
So improve on this by having a callback in the backref walking code that
is called when it finds the extent item in the extent tree, and have those
checks done in the callback. When the callback returns anything different
from 0, it stops the backref walking code. This way we do a single search
on the extent tree for the extent item of our data extent.
Also, before this change we were only checking the number of references on
the data extent against SEND_MAX_EXTENT_REFS, but after starting backref
walking we will end up resolving backrefs for extent buffers in the path
from a leaf having a file extent item pointing to our data extent, up to
roots of trees from which the extent buffer is accessible from, due to
shared subtrees resulting from snapshoting. We were therefore allowing for
the possibility for send taking too long due to some node in the path from
the leaf to a root node being shared too many times. After this change we
check for reference counts being greater than SEND_MAX_EXTENT_REFS for
both data extents and metadata extents.
This change is part of a patchset comprised of the following patches:
01/17 btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
02/17 btrfs: fix inode list leak during backref walking at find_parent_nodes()
03/17 btrfs: fix ulist leaks in error paths of qgroup self tests
04/17 btrfs: remove pointless and double ulist frees in error paths of qgroup tests
05/17 btrfs: send: avoid unnecessary path allocations when finding extent clone
06/17 btrfs: send: update comment at find_extent_clone()
07/17 btrfs: send: drop unnecessary backref context field initializations
08/17 btrfs: send: avoid unnecessary backref lookups when finding clone source
09/17 btrfs: send: optimize clone detection to increase extent sharing
10/17 btrfs: use a single argument for extent offset in backref walking functions
11/17 btrfs: use a structure to pass arguments to backref walking functions
12/17 btrfs: reuse roots ulist on each leaf iteration for iterate_extent_inodes()
13/17 btrfs: constify ulist parameter of ulist_next()
14/17 btrfs: send: cache leaf to roots mapping during backref walking
15/17 btrfs: send: skip unnecessary backref iterations
16/17 btrfs: send: avoid double extent tree search when finding clone source
17/17 btrfs: send: skip resolution of our own backref when finding clone source
Performance test results are in the changelog of patch 17/17.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:51 +0000 (16:15 +0000)]
btrfs: send: skip unnecessary backref iterations
When looking for a clone source for an extent, we are iterating over all
the backreferences for an extent. This is often a waste of time, because
once we find a good clone source we could stop immediately instead of
continuing backref walking, which is expensive.
Basically what happens currently is this:
1) Call iterate_extent_inodes() to iterate over all the backreferences;
2) It calls btrfs_find_all_leafs() which in turn calls the main function
to walk over backrefs and collect them - find_parent_nodes();
3) Then we collect all the references for our target data extent from the
extent tree (and delayed refs if any), add them to the rb trees,
resolve all the indirect backreferences and search for all the file
extent items in fs trees, building a list of inodes for each one of
them (struct extent_inode_elem);
4) Then back at iterate_extent_inodes() we find all the roots associated
to each found leaf, and call the callback __iterate_backrefs defined
at send.c for each inode in the inode list associated to each leaf.
Some times one the first backreferences we find in a fs tree is optimal
to satisfy the clone operation that send wants to perform, and in that
case we could stop immediately and avoid resolving all the remaining
indirect backreferences (search fs trees for the respective file extent
items, etc). This possibly if when we find a fs tree leaf with a file
extent item we are able to know what are all the roots that can lead to
the leaf - this is now possible after the previous patch in the series
that adds a cache that maps leaves to a list of roots. So we can now
shortcircuit backref walking during send, by having the callback we
pass to iterate_extent_inodes() to be called when we find a file extent
item for an indirect backreference, and have it return a special value
when it found a suitable backreference and it does not need to look for
more backreferences. This change does that.
This change is part of a patchset comprised of the following patches:
01/17 btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
02/17 btrfs: fix inode list leak during backref walking at find_parent_nodes()
03/17 btrfs: fix ulist leaks in error paths of qgroup self tests
04/17 btrfs: remove pointless and double ulist frees in error paths of qgroup tests
05/17 btrfs: send: avoid unnecessary path allocations when finding extent clone
06/17 btrfs: send: update comment at find_extent_clone()
07/17 btrfs: send: drop unnecessary backref context field initializations
08/17 btrfs: send: avoid unnecessary backref lookups when finding clone source
09/17 btrfs: send: optimize clone detection to increase extent sharing
10/17 btrfs: use a single argument for extent offset in backref walking functions
11/17 btrfs: use a structure to pass arguments to backref walking functions
12/17 btrfs: reuse roots ulist on each leaf iteration for iterate_extent_inodes()
13/17 btrfs: constify ulist parameter of ulist_next()
14/17 btrfs: send: cache leaf to roots mapping during backref walking
15/17 btrfs: send: skip unnecessary backref iterations
16/17 btrfs: send: avoid double extent tree search when finding clone source
17/17 btrfs: send: skip resolution of our own backref when finding clone source
Performance test results are in the changelog of patch 17/17.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:50 +0000 (16:15 +0000)]
btrfs: send: cache leaf to roots mapping during backref walking
During a send operation, when doing backref walking to determine which
inodes/offsets/roots we can clone from, the most repetitive and expensive
step is to map each leaf that has file extent items pointing to the target
data extent to the IDs of the roots from which the leaves are accessible,
which happens at iterate_extent_inodes(). That step requires finding every
parent node of a leaf, then the parent of each parent, and so on until we
reach a root node. So it's a naturally expensive operation, and repetitive
because each leaf can have hundreds of file extent items (for a nodesize
of 16K, that can be slightly over 200 file extent items). There's also
temporal locality, as we process all file extent items from a leave before
moving the next leaf.
This change caches the mapping of leaves to root IDs, to avoid repeating
those computations over and over again. The cache is limited to a maximum
of 128 entries, with each entry being a struct with a size of 128 bytes,
so the maximum cache size is 16K plus any nodes internally allocated by
the maple tree that is used to index pointers to those structs. The cache
is invalidated whenever we detect relocation happened since we started
filling the cache, because if relocation happened then extent buffers for
leaves and nodes of the trees used by a send operation may have been
reallocated.
This cache also allows for another important optimization that is
introduced in the next patch in the series.
This change is part of a patchset comprised of the following patches:
01/17 btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
02/17 btrfs: fix inode list leak during backref walking at find_parent_nodes()
03/17 btrfs: fix ulist leaks in error paths of qgroup self tests
04/17 btrfs: remove pointless and double ulist frees in error paths of qgroup tests
05/17 btrfs: send: avoid unnecessary path allocations when finding extent clone
06/17 btrfs: send: update comment at find_extent_clone()
07/17 btrfs: send: drop unnecessary backref context field initializations
08/17 btrfs: send: avoid unnecessary backref lookups when finding clone source
09/17 btrfs: send: optimize clone detection to increase extent sharing
10/17 btrfs: use a single argument for extent offset in backref walking functions
11/17 btrfs: use a structure to pass arguments to backref walking functions
12/17 btrfs: reuse roots ulist on each leaf iteration for iterate_extent_inodes()
13/17 btrfs: constify ulist parameter of ulist_next()
14/17 btrfs: send: cache leaf to roots mapping during backref walking
15/17 btrfs: send: skip unnecessary backref iterations
16/17 btrfs: send: avoid double extent tree search when finding clone source
17/17 btrfs: send: skip resolution of our own backref when finding clone source
Performance test results are in the changelog of patch 17/17.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:49 +0000 (16:15 +0000)]
btrfs: constify ulist parameter of ulist_next()
The ulist_next() iterator function does not need to change the given ulist
so make it const. This will allow the next patch in the series to pass a
ulist to a function that does not need, and should not, modify the ulist.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:48 +0000 (16:15 +0000)]
btrfs: reuse roots ulist on each leaf iteration for iterate_extent_inodes()
At iterate_extent_inodes() we collect a ulist of leaves for a given extent
with a call to btrfs_find_all_leafs() and then we enter a loop where we
iterate over all the collected leaves. Each iteration of that loop does a
call to btrfs_find_all_roots_safe(), to determine all roots from which a
leaf is accessible, and that results in allocating and releasing a ulist
to store the root IDs.
Instead of allocating and releasing the roots ulist on every iteration,
allocate a ulist before entering the loop and keep using it on each
iteration, reinitializing the ulist at the end of each iteration.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:47 +0000 (16:15 +0000)]
btrfs: use a structure to pass arguments to backref walking functions
The public backref walking functions have quite a lot of arguments that
are passed down the call stack to find_parent_nodes(), the core function
of the backref walking code.
The next patches in series will need to add even arguments to these
functions that should be passed not only to find_parent_nodes(), but also
to other functions used by the later (directly or even lower in the call
stack).
So create a structure to hold all these arguments and state used by the
main backref walking function, find_parent_nodes(), and use it as the
argument for the public backref walking functions iterate_extent_inodes(),
btrfs_find_all_leafs() and btrfs_find_all_roots().
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:46 +0000 (16:15 +0000)]
btrfs: use a single argument for extent offset in backref walking functions
The interface for find_parent_nodes() has two extent offset related
arguments:
1) One u64 pointer argument for the extent offset;
2) One boolean argument to tell if the extent offset should be ignored or
not.
These are confusing, becase the extent offset pointer can be NULL and in
some cases callers pass a NULL value as a way to tell the backref walking
code to ignore offsets in file extent items (and simply consider all file
extent items that point to the target data extent).
The boolean argument was added in commit
c995ab3cda3f ("btrfs: add a flag
to iterate_inodes_from_logical to find all extent refs for uncompressed
extents"), but it was never really necessary, it was enough if it could
find a way to get a NULL value passed to the "extent_item_pos" argument of
find_parent_nodes(). The arguments are also passed to functions called
by find_parent_nodes() and respective helper functions, which further
makes everything more complicated than needed.
Then we have several backref walking related functions that end up calling
find_parent_nodes(), either directly or through some other function that
they call, and for many we have to use an "extent_item_pos" (u64) argument
and a boolean "ignore_offset" argument too.
This is confusing and not really necessary. So use a single argument to
specify the extent offset, as a simple u64 and not as a pointer, but
using a special value of (u64)-1, defined as a documented constant, to
indicate when the extent offset should be ignored.
This is also preparation work for the upcoming patches in the series that
add other arguments to find_parent_nodes() and other related functions
that use it.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:45 +0000 (16:15 +0000)]
btrfs: send: optimize clone detection to increase extent sharing
Currently send does not do the best decisions when it comes to decide
between multiple clone sources, which results in clone operations for
partial extent ranges, which has the following disadvantages:
1) We get less shared extents at the destination;
2) We have to read more data during the send operation and emit more
write commands.
Besides not being optimal behaviour, it also breaks user expectations and
is often reported by users, with a recent example in the Link tag at the
bottom of this change log.
Part of the reason for this non-optimal behaviour is that the backref
walking code does not provide information about the length of the file
extent items that were found for each backref, so send is blind about
which backref is the best to chose as a cloning source.
The other existing reasons are just silliness, namely always prefering
the inode with the lowest number when multiple are found for the same
root and when we can clone from multiple roots, always prefer the send
root over any of the other clone roots. This does not make any sense
since any inode or root is fine and as good as any other inode/root.
Fix this by making backref walking pass information about the number of
bytes referenced by each file extent item and then have send's backref
callback pick the inode with the highest number of bytes for each root.
Finally select the root from which we can clone more bytes from.
Example reproducer:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV
mount $DEV $MNT
xfs_io -f -c "pwrite -S 0xab -b 2M 0 2M" $MNT/foo
cp --reflink=always $MNT/foo $MNT/bar
cp --reflink=always $MNT/foo $MNT/baz
sync
# Overwrite the second half of file foo.
xfs_io -c "pwrite -S 0xcd -b 1M 1M 1M" $MNT/foo
sync
echo
echo "*** fiemap in the original filesystem ***"
echo
xfs_io -c "fiemap -v" $MNT/foo
xfs_io -c "fiemap -v" $MNT/bar
xfs_io -c "fiemap -v" $MNT/baz
echo
btrfs filesystem du $MNT
btrfs subvolume snapshot -r $MNT $MNT/snap
btrfs send -f /tmp/send_stream $MNT/snap
umount $MNT
mkfs.btrfs -f $DEV &> /dev/null
mount $DEV $MNT
btrfs receive -f /tmp/send_stream $MNT
echo
echo "*** fiemap in the new filesystem ***"
echo
xfs_io -r -c "fiemap -v" $MNT/snap/foo
xfs_io -r -c "fiemap -v" $MNT/snap/bar
xfs_io -r -c "fiemap -v" $MNT/snap/baz
echo
btrfs filesystem du $MNT
rm -f /tmp/send_stream
rm -f /tmp/snap.fssum
umount $MNT
Before this change:
$ ./test.sh
(...)
*** fiemap in the original filesystem ***
/mnt/sdi/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..2047]: 26624..28671 2048 0x2000
1: [2048..4095]: 30720..32767 2048 0x1
/mnt/sdi/bar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..4095]: 26624..30719 4096 0x2001
/mnt/sdi/baz:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..4095]: 26624..30719 4096 0x2001
Total Exclusive Set shared Filename
2.00MiB 1.00MiB - /mnt/sdi/foo
2.00MiB 0.00B - /mnt/sdi/bar
2.00MiB 0.00B - /mnt/sdi/baz
6.00MiB 1.00MiB 2.00MiB /mnt/sdi
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap'
At subvol /mnt/sdi/snap
At subvol snap
*** fiemap in the new filesystem ***
/mnt/sdi/snap/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..4095]: 26624..30719 4096 0x2001
/mnt/sdi/snap/bar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..2047]: 26624..28671 2048 0x2000
1: [2048..4095]: 30720..32767 2048 0x1
/mnt/sdi/snap/baz:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..2047]: 26624..28671 2048 0x2000
1: [2048..4095]: 32768..34815 2048 0x1
Total Exclusive Set shared Filename
2.00MiB 0.00B - /mnt/sdi/snap/foo
2.00MiB 1.00MiB - /mnt/sdi/snap/bar
2.00MiB 1.00MiB - /mnt/sdi/snap/baz
6.00MiB 2.00MiB - /mnt/sdi/snap
6.00MiB 2.00MiB 2.00MiB /mnt/sdi
We end up with two 1M extents that are not shared for files bar and baz.
After this change:
$ ./test.sh
(...)
*** fiemap in the original filesystem ***
/mnt/sdi/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..2047]: 26624..28671 2048 0x2000
1: [2048..4095]: 30720..32767 2048 0x1
/mnt/sdi/bar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..4095]: 26624..30719 4096 0x2001
/mnt/sdi/baz:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..4095]: 26624..30719 4096 0x2001
Total Exclusive Set shared Filename
2.00MiB 1.00MiB - /mnt/sdi/foo
2.00MiB 0.00B - /mnt/sdi/bar
2.00MiB 0.00B - /mnt/sdi/baz
6.00MiB 1.00MiB 2.00MiB /mnt/sdi
Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap'
At subvol /mnt/sdi/snap
At subvol snap
*** fiemap in the new filesystem ***
/mnt/sdi/snap/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..4095]: 26624..30719 4096 0x2001
/mnt/sdi/snap/bar:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..2047]: 26624..28671 2048 0x2000
1: [2048..4095]: 30720..32767 2048 0x2001
/mnt/sdi/snap/baz:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..2047]: 26624..28671 2048 0x2000
1: [2048..4095]: 30720..32767 2048 0x2001
Total Exclusive Set shared Filename
2.00MiB 0.00B - /mnt/sdi/snap/foo
2.00MiB 0.00B - /mnt/sdi/snap/bar
2.00MiB 0.00B - /mnt/sdi/snap/baz
6.00MiB 0.00B - /mnt/sdi/snap
6.00MiB 0.00B 3.00MiB /mnt/sdi
Now there's a much better sharing, files bar and baz share 1M of the
extent of file foo and the second extent of files bar and baz is shared
between themselves.
This will later be turned into a test case for fstests.
Link: https://lore.kernel.org/linux-btrfs/20221008005704.795b44b0@crass-HP-ZBook-15-G2/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:44 +0000 (16:15 +0000)]
btrfs: send: avoid unnecessary backref lookups when finding clone source
At find_extent_clone(), unless we are given an inline extent, a file
extent item that represents hole or an extent that starts beyond the
i_size, we always do backref walking to look for clone sources, unless
if we have more than SEND_MAX_EXTENT_REFS (64) known references on the
extent.
However if we know we only have one reference in the extent item and only
one clone source (the send root), then it's pointless to do the backref
walking to search for clone sources, as we can't clone from any other
root. So skip the backref walking in that case.
The following test was run on a non-debug kernel (Debian's default kernel
config):
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV
mount $DEV $MNT
# Create an extent tree that's not too small and none of the
# extents is shared.
for ((i = 1; i <= 50000; i++)); do
xfs_io -f -c "pwrite 0 4K" $MNT/file_$i > /dev/null
echo -ne "\r$i files created..."
done
echo
btrfs subvolume snapshot -r $MNT $MNT/snap
start=$(date +%s%N)
btrfs send $MNT/snap > /dev/null
end=$(date +%s%N)
dur=$(( (end - start) /
1000000 ))
echo -e "\nsend took $dur milliseconds"
umount $MNT
Before this change:
send took 5389 milliseconds
After this change:
send took 4519 milliseconds (-16.1%)
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:43 +0000 (16:15 +0000)]
btrfs: send: drop unnecessary backref context field initializations
At find_extent_clone() we are initializing to zero the 'found_itself' and
'found' fields of the backref context before we use it but we have already
initialized the structure to zeroes when we declared it on stack, so it's
pointless to initialize those fields and they are unnecessarily increasing
the object text size with two "mov" instructions (x86_64).
Similarly make the 'extent_len' initialization more clear by using an if-
-then-else instead of a double assignment to it in case the extent's end
crosses the i_size boundary.
Before this change:
$ size fs/btrfs/send.o
text data bss dec hex filename
68694 4252 16 72962 11d02 fs/btrfs/send.o
After this change:
$ size fs/btrfs/send.o
text data bss dec hex filename
68678 4252 16 72946 11cf2 fs/btrfs/send.o
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:42 +0000 (16:15 +0000)]
btrfs: send: update comment at find_extent_clone()
We have this unclear comment at find_extent_clone() about extents starting
at a file offset greater than or equals to the i_size of the inode. It's
not really informative and it's misleading, since it mentions the author
found such extents with snapshots and large files.
Such extents are a result of fallocate with FALLOC_FL_KEEP_SIZE and there
is no relation to snapshots or large files (all write paths update the
i_size before inserting a new file extent item). So update the comment to
be precise about it and why we don't bother looking for clone sources in
that case.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 1 Nov 2022 16:15:41 +0000 (16:15 +0000)]
btrfs: send: avoid unnecessary path allocations when finding extent clone
When looking for an extent clone, at find_extent_clone(), we start by
allocating a path and then check for cases where we can't have clones
and exit immediately in those cases. It's a waste of time to allocate
the path before those cases, so reorder the logic so that we check for
those cases before allocating the path.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:12 +0000 (19:16 +0800)]
btrfs: remove the unused endio_raid56_workers and btrfs_raid_bio::end_io_work
Since we have switched all raid56 workload to submit-and-wait method,
there is no use for btrfs_fs_info::endio_raid56_workers workqueue and
btrfs_raid_bio::end_io_work.
Remove them to save some memory.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:11 +0000 (19:16 +0800)]
btrfs: raid56: switch scrub path to use a single function
This switch involves the following changes:
- Make finish_parity_scrub() only to submit the write bios
It will no longer call rbio_orig_end_io(), and now it will
return error.
- Add a new helper, recover_scrub_rbio(), to handle recovery
It's just doing extra scrub related checks, and then call
recover_sectors().
- Rename raid56_parity_scrub_stripe() to scrub_rbio()
- Rename scrub_parity_work() to scrub_rbio_work_locked()
To follow the existing naming scheme.
- Delete unused functions
Including:
* finish_rmw()
* raid_write_end_io()
* raid56_bio_end_io()
* __raid_recover_end_io()
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:10 +0000 (19:16 +0800)]
btrfs: raid56: extract scrub read bio list assembly code into a helper
Just like what we did for write/recovery, also extract the read bio
assembly code into a helper for scrub.
The difference between the three are:
- rmw_assemble_read_bios() only submit reads for missing sectors
Thus it will skip cached sectors, but will also read sectors which
is not covered by any full stripe. (For cache usage)
- recover_assemble_read_bios() reads every sector which has not failed
- scrub_assemble_read_bios() has extra check for vertical stripes
It's mostly the same as rmw_assemble_read_bios(), but will skip
sectors which is not covered by a vertical stripe.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:09 +0000 (19:16 +0800)]
btrfs: raid56: switch write path to rmw_rbio()
This includes the following changes:
- Implement new raid_unplug() functions
Now we don't need a workqueue to run the plug, as all our
work is just queue rmw_rbio_work() call, which can be executed
without sleep.
- Implement a rmw_rbio_work_locked() helper
This is for unlock_stripe(), which is already holding the full stripe
lock.
- Remove all the old functions
This should already shows how complex the old functions are, as we
ended up removing the following functions:
* rmw_work()
* validate_rbio_for_rmw()
* raid56_rmw_end_io_work()
* raid56_rmw_stripe()
* full_stripe_write()
* partial_stripe_write()
* __raid56_parity_write()
* run_plug()
* unplug_work()
* btrfs_raid_unplug()
* rmw_work()
* __raid56_parity_recover()
* raid_recover_end_io_work()
- Unexport rmw_rbio()
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:08 +0000 (19:16 +0800)]
btrfs: raid56: introduce the main entrance for RMW path
The new entrance will be called rmw_rbio(), it will have a streamlined
workflow by using submit-and-wait method.
Thus there will be no weird jumps between tons of functions, thus way
more reader friendly, and will make later expansion easier, as it's now
a straight workflow, the timing is way more clear.
Unfortunately we can not yet migrate the RMW path to use this new
entrance as we still need extra work to address the plug and
unlock_stripe() function.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:07 +0000 (19:16 +0800)]
btrfs: raid56: extract rwm write bios assembly into a helper
The helper will be later used to refactor the rmw write path.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:06 +0000 (19:16 +0800)]
btrfs: raid56: extract the rmw bio list build code into a helper
The helper will later be used to refactor the whole RMW path.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:05 +0000 (19:16 +0800)]
btrfs: raid56: switch recovery path to a single function
Currently btrfs uses end_io functions to jump between different stages
of recovery.
For example, we go the following different functions:
- raid56_bio_end_io()
This handles the read for all the sectors (except the missing device).
- __raid_recover_end_io()
This does the real work, it's called inside the delayed work function
raid_recover_end_io_work().
This one recovery path involves at least 3 different functions, which is
a big burden for readers.
This patch will change the behavior by:
- Introduce a unified recovery entrance, recover_rbio()
- Use submit-and-wait method
So the workflow is not interrupted by the endio function jump.
This doesn't bring performance change, but reduce the burden for
reviewers.
- Run the main function in the rmw_workers workqueue
Now raid56_parity_recover() only needs to setup the work, and
queue the work using start_async_work().
Now readers only need to do one function jump (start_async_work()) to
find out the main entrance of recovery path.
Furthermore, recover_rbio() function can easily be reused by other paths.
The old recovery path is still utilized by degraded write path.
It will be cleaned up when we have migrated the write path.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:04 +0000 (19:16 +0800)]
btrfs: raid56: extract sector recovery code into a helper
This includes extra changes:
- The allocation for unmap_array[] and pointers[]
Now we allocate them in one go, and free them together.
- Remove @err
Use errno_to_blk_status(ret) instead.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:03 +0000 (19:16 +0800)]
btrfs: raid56: extract the recovery bio list build code into a helper
This new helper will be also utilized in the incoming refactor of
recovery path.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:02 +0000 (19:16 +0800)]
btrfs: raid56: extract the pq generation code into a helper
Currently finish_rmw() will update the P/Q stripes before submitting
the writes.
It's done behind a for(;;) loop, it's a little congested indent-wise, so
extract the code into a helper called generate_pq_vertical().
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 1 Nov 2022 11:16:01 +0000 (19:16 +0800)]
btrfs: raid56: extract the vertical stripe recovery code into recover_vertical()
This refactor includes the following behavior change first:
- Don't error out if only P/Q is corrupted
The old code will directly error out if only P/Q is corrupted.
Although it is an logical error if we go into rebuild path with
only P/Q corrupted, there is no need to error out.
Just skip the rebuild and return the already good data.
Then comes the following refactor which shouldn't cause behavior
changes:
- Introduce a helper to do vertical stripe recovery
This not only reduce one indent level, but also paves the road for
later data checksum verification in RMW cycles.
- Sort rbio->faila/b before recovery
So we don't need to do the same swap every vertical stripe
- Replace a BUG_ON() with ASSERT()
Or checkpatch won't let me pass.
- Mark recovered sectors uptodate after the recover loop
- Do the cleanup for pointers unconditionally
We only need to initialize @pointers and @unmap_array to NULL, so
we can safely free them unconditionally.
- Mark the repaired sector uptodate in recover_vertical()
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 11:07:05 +0000 (13:07 +0200)]
btrfs: merge struct extent_page_data to btrfs_bio_ctrl
The two structures appear on the same call paths, btrfs_bio_ctrl is
embedded in extent_page_data and we pass bio_ctrl to some functions.
After merging there are fewer indirections and we have only one control
structure. The packing remains same.
The btrfs_bio_ctrl was selected as the target structure as the operation
is closer to bio processing.
Structure layout:
struct btrfs_bio_ctrl {
struct bio * bio; /* 0 8 */
int mirror_num; /* 8 4 */
enum btrfs_compression_type compress_type; /* 12 4 */
u32 len_to_stripe_boundary; /* 16 4 */
u32 len_to_oe_boundary; /* 20 4 */
btrfs_bio_end_io_t end_io_func; /* 24 8 */
bool extent_locked; /* 32 1 */
bool sync_io; /* 33 1 */
/* size: 40, cachelines: 1, members: 8 */
/* padding: 6 */
/* last cacheline: 40 bytes */
};
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 11:07:03 +0000 (13:07 +0200)]
btrfs: switch extent_page_data bit fields to bools
The semantics of the two members is a boolean, so change the type
accordingly. We have space in extent_page_data due to alignment there's
no change in size.
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Wed, 26 Oct 2022 21:25:14 +0000 (23:25 +0200)]
btrfs: simplify percent calculation helpers, rename div_factor
The div_factor* helpers calculate fraction or percentage fraction. The
name is a bit confusing, we use it only for percentage calculations and
there are two helpers.
There's a helper mult_frac that's for general fractions, that tries to
be accurate but we multiply and divide by small numbers so we can use
the div_u64 helper.
Rename the div_factor* helpers and use 1..100 percentage range, also drop
the case checking for percentage == 100, it's never hit.
The conversions:
* div_factor calculates tenths and the numbers need to be adjusted
* div_factor_fine is direct replacement
Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Mon, 31 Oct 2022 11:43:56 +0000 (11:43 +0000)]
btrfs: update stale comment for nowait direct IO writes
If when doing a direct IO write we need to fallback to buffered IO, we
this comment at btrfs_direct_write() that says we can't directly fallback
to buffered IO if we have a NOWAIT iocb, because we have no support for
NOWAIT buffered writes. That is not true anymore, as support for NOWAIT
buffered writes was added recently in commit
926078b21db9 ("btrfs: enable
nowait async buffered writes").
However we still can't fallback to a buffered write in case we have a
NOWAIT iocb, because we'll need to flush delalloc and wait for it to
complete after doing the buffered write, and that can block for several
reasons, the main reason being waiting for IO to complete.
So update the comment to mention all that.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Thu, 27 Oct 2022 16:12:04 +0000 (18:12 +0200)]
btrfs: fix SPDX comment in tree-mod-log.h
The header files should use the /* */ comment style, introduced in
commit
f3a84ccd28d0 ("btrfs: move the tree mod log code into its own
file").
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 16 Sep 2022 07:28:39 +0000 (15:28 +0800)]
btrfs: extract the inline extent read code into its own function
Currently we have inline extent read code behind two levels of
indentation, factor them them out into a new function,
read_inline_extent(), to make it a little easier to read.
Since we're here, also remove @extent_offset and @pg_offset arguments
from uncompress_inline() function, as it's not possible to have inline
extents at non-inline file offset.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 16 Sep 2022 07:28:38 +0000 (15:28 +0800)]
btrfs: remove new_inline argument from btrfs_extent_item_to_extent_map()
The argument @new_inline changes the following members of extent_map:
- em->compress_type
- EXTENT_FLAG_COMPRESSED of em->flags
However neither members makes a difference for inline extents:
- Inline extent read never use above em members
As inside btrfs_get_extent() we directly use the file extent item to
do the read.
- Inline extents are never to be split
Thus code really needs em->compress_type or that flag will never be
executed on inlined extents.
(btrfs_drop_extent_cache() would be one example)
- Fiemap no longer relies on extent maps
Recent fiemap optimization makes fiemap to search subvolume tree
directly, without using any extent map at all.
Thus those members make no difference for inline extents any more.
Furthermore such exception without much explanation is really a source
of confusion.
Thus this patch will completely remove the argument, and always set the
involved members, unifying the behavior.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 16 Sep 2022 07:28:37 +0000 (15:28 +0800)]
btrfs: do not reset extent map members for inline extents read
Currently for inline extents read inside btrfs_get_extent(), we will
reset several extent map members:
- em->start
Reset to extent_start, which is completely unnecessary.
The extent_start and em->start should have already be zero, ensured by
tree-checker already.
- em->len
Reset the round_up(copy_size, fs_info->sectorsize), which is again
unnecessary.
- em->orig_block_len
Reset to em->len (sectorsize), while it is originally unset from
btrfs_extent_item_to_extent_map().
This makes no difference, as all extent map handling paths will
ignore the orig_block_len if they found it's an inlined extent.
Such inline extent orig_block_len ignoring examples can be found in
btrfs_drop_extent_cache().
- em->orig_start
Reset to em->start (0), while it is originally set to EXTENT_MAP_HOLE.
This makes no difference either, as all extent map handling paths will
ignore the em->orig_start if they found it's an inline extent.
Thus all these em members resetting are unnecessary.
Replace them with ASSERT()s checking the only two members (block_start
and length) that make sense.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 16 Sep 2022 07:28:36 +0000 (15:28 +0800)]
btrfs: make inline extent read calculation much simpler
Currently we calculate inline extent read in a way that inline extent
can start at non-zero offset.
This is consistent with the inode selftests, which puts an inline extent
at file offset 5.
Meanwhile the inline extent creation code will only create inline extent
at file offset 0.
Furthermore with the introduction of tree-checker on file extents, we are
actively rejecting inline extent which starts at non-zero file offset.
And so far we haven't yet seen any report of rejected inline extents at
non-zero file offset.
This all means, the extra calculation to support inline extents at
non-zero file offset is mostly paper weight, and damaging the
readability of the code.
Thus this patch will:
- Add extra ASSERT()s to make sure involved file offset are all 0
- Remove @extent_offset calculation
- Simplify the involved code
As several variables are now single-use, no need to declare them as
a variable anymore.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 16 Sep 2022 07:28:35 +0000 (15:28 +0800)]
btrfs: selftests: remove impossible inline extent at non-zero file offset
In our inode-tests.c, we create an inline offset at file offset 5, which
is no longer possible since the introduction of tree-checker.
Thus I don't think we should spend time maintaining some corner cases
which are already ruled out by tree-checker.
So this patch will:
- Change the inline extent to start at file offset 0
Also change its length to 6 to cover the original length
- Add an extra ASSERT() for btrfs_add_extent_mapping()
This is to make sure tree-checker is working correctly.
- Update the inode selftest
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 26 Oct 2022 19:08:41 +0000 (15:08 -0400)]
btrfs: move orphan prototypes into orphan.h
Move these out of ctree.h into orphan.h to cut down on code in ctree.h.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 26 Oct 2022 19:08:40 +0000 (15:08 -0400)]
btrfs: move super_block specific helpers into super.h
This will make syncing fs.h to user space a little easier if we can pull
the super block specific helpers out of fs.h and put them in super.h.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 26 Oct 2022 19:08:39 +0000 (15:08 -0400)]
btrfs: move super prototypes into super.h
Move these out of ctree.h into super.h to cut down on code in ctree.h.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 26 Oct 2022 19:08:38 +0000 (15:08 -0400)]
btrfs: move CONFIG_BTRFS_FS_RUN_SANITY_TESTS checks to fs.h
We already have a few of these in fs.h, move the remaining checks out of
ctree.h into fs.h.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 26 Oct 2022 19:08:37 +0000 (15:08 -0400)]
btrfs: move verity prototypes into verity.h
Move these out of ctree.h into verity.h to cut down on code in ctree.h.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 26 Oct 2022 19:08:36 +0000 (15:08 -0400)]
btrfs: move dev-replace prototypes into dev-replace.h
We already have a dev-replace.h, simply move these prototypes and
helpers into dev-replace.h where they belong.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 26 Oct 2022 19:08:35 +0000 (15:08 -0400)]
btrfs: move scrub prototypes into scrub.h
Move these out of ctree.h into scrub.h to cut down on code in ctree.h.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 26 Oct 2022 19:08:34 +0000 (15:08 -0400)]
btrfs: move relocation prototypes into relocation.h
Move these out of ctree.h into relocation.h to cut down on code in
ctree.h
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 26 Oct 2022 19:08:33 +0000 (15:08 -0400)]
btrfs: move acl prototypes into acl.h
Move these out of ctree.h into acl.h to cut down on code in ctree.h.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>