OSDN Git Service
David S. Miller [Thu, 25 Jan 2018 04:48:11 +0000 (23:48 -0500)]
Merge branch 'rebased-net-ioctl' of git://git./linux/kernel/git/viro/vfs
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 25 Jan 2018 04:44:15 +0000 (23:44 -0500)]
Merge git://git./linux/kernel/git/davem/net
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 25 Jan 2018 01:24:30 +0000 (17:24 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Avoid negative netdev refcount in error flow of xfrm state add, from
Aviad Yehezkel.
2) Fix tcpdump decoding of IPSEC decap'd frames by filling in the
ethernet header protocol field in xfrm{4,6}_mode_tunnel_input().
From Yossi Kuperman.
3) Fix a syzbot triggered skb_under_panic in pppoe having to do with
failing to allocate an appropriate amount of headroom. From
Guillaume Nault.
4) Fix memory leak in vmxnet3 driver, from Neil Horman.
5) Cure out-of-bounds packet memory access in em_nbyte EMATCH module,
from Wolfgang Bumiller.
6) Restrict what kinds of sockets can be bound to the KCM multiplexer
and also disallow when another layer has attached to the socket and
made use of sk_user_data. From Tom Herbert.
7) Fix use before init of IOTLB in vhost code, from Jason Wang.
8) Correct STACR register write bit definition in IBM emac driver, from
Ivan Mikhaylov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net/ibm/emac: wrong bit is used for STA control register write
net/ibm/emac: add 8192 rx/tx fifo size
vhost: do not try to access device IOTLB when not initialized
vhost: use mutex_lock_nested() in vhost_dev_lock_vqs()
i40e: flower: check if TC offload is enabled on a netdev
qed: Free reserved MR tid
qed: Remove reserveration of dpi for kernel
kcm: Check if sk_user_data already set in kcm_attach
kcm: Only allow TCP sockets to be attached to a KCM mux
net: sched: fix TCF_LAYER_LINK case in tcf_get_base_ptr
net: sched: em_nbyte: don't add the data offset twice
mlxsw: spectrum_router: Don't log an error on missing neighbor
vmxnet3: repair memory leak
ipv6: Fix getsockopt() for sockets with default IPV6_AUTOFLOWLABEL
pppoe: take ->needed_headroom of lower device into account on xmit
xfrm: fix boolean assignment in xfrm_get_type_offload
xfrm: Fix eth_hdr(skb)->h_proto to reflect inner IP version
xfrm: fix error flow in case of add state fails
xfrm: Add SA to hardware at the end of xfrm_state_construct()
Al Viro [Sat, 1 Jul 2017 22:46:30 +0000 (18:46 -0400)]
kill kernel_sock_ioctl()
no users since 2014
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Thu, 5 Oct 2017 16:59:44 +0000 (12:59 -0400)]
dev_ioctl(): move copyin/copyout to callers
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Mon, 2 Oct 2017 00:27:01 +0000 (20:27 -0400)]
ipconfig: use dev_set_mtu()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Mon, 2 Oct 2017 00:13:08 +0000 (20:13 -0400)]
lift handling of SIOCIW... out of dev_ioctl()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Mon, 2 Oct 2017 01:12:09 +0000 (21:12 -0400)]
kill dev_ifname32()
same story...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 30 Sep 2017 23:32:17 +0000 (19:32 -0400)]
kill bond_ioctl()
Same story as with dev_ifsioc(), except that the last cases with non-trivial
conversions had been taken out in 2013...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 30 Sep 2017 23:31:15 +0000 (19:31 -0400)]
kill dev_ifsioc()
Once upon a time net/socket.c:dev_ifsioc() used to handle SIOCSHWTSTAMP and
SIOCSIFMAP. These have different native and compat layout, so the format
conversion had been needed. In 2009 these two cases had been taken out,
turning the rest into a convoluted way to calling sock_do_ioctl(). We copy
compat structure into native one, call sock_do_ioctl() on that and copy
the result back for the in/out ioctls. No layout transformation anywhere,
so we might as well just call sock_do_ioctl() and skip all the headache with
copying.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 1 Jul 2017 12:03:10 +0000 (08:03 -0400)]
ip_rt_ioctl(): take copyin to caller
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 1 Jul 2017 11:53:12 +0000 (07:53 -0400)]
devinet_ioctl(): take copyin/copyout to caller
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Mon, 26 Jun 2017 17:19:16 +0000 (13:19 -0400)]
net: separate SIOCGIFCONF handling from dev_ioctl()
Only two of dev_ioctl() callers may pass SIOCGIFCONF to it.
Separating that codepath from the rest of dev_ioctl() allows both
to simplify dev_ioctl() itself (all other cases work with struct ifreq *)
*and* seriously simplify the compat side of that beast: all it takes
is passing to inet_gifconf() an extra argument - the size of individual
records (sizeof(struct ifreq) or sizeof(struct compat_ifreq)). With
dev_ifconf() called directly from sock_do_ioctl()/compat_dev_ifconf()
that's easy to arrange.
As the result, compat side of SIOCGIFCONF doesn't need any
allocations, copy_in_user() back and forth, etc.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Wed, 24 Jan 2018 23:49:02 +0000 (15:49 -0800)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc bugfix from David Miller:
"Sparc Makefile typo fix"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: fix typo in CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64
Ivan Mikhaylov [Wed, 24 Jan 2018 12:53:25 +0000 (15:53 +0300)]
net/ibm/emac: wrong bit is used for STA control register write
STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Mikhaylov [Wed, 24 Jan 2018 12:53:24 +0000 (15:53 +0300)]
net/ibm/emac: add 8192 rx/tx fifo size
emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 23:02:17 +0000 (18:02 -0500)]
Merge branch '100GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-01-24
This series contains updates to fm10k only.
Alex fixes MACVLAN offload for fm10k, where we were not seeing unicast
packets being received because we did not correctly configure the
default VLAN ID for the port and defaulting to 0.
Jake cleans up unnecessary parenthesis in a couple of "if" statements.
Fixed the driver to stop adding VLAN 0 into the VLAN table, since it
would cause the VLAN table to be inconsistent between the PF and VF.
Also fixed an issue where we were assuming that VLAN 1 is enabled when
the default VLAN ID is not set, so resolve by not requesting any filters
for the default_vid if it has not yet been assigned.
Ngai fixes an issue which was generating a dmesg regarding unbale to
kill a particular VLAN ID for the device. This is due to
ndo_vlan_rx_kill_vid() exits with an error and the handler for this ndo
is fm10k_update_vid() which exits prematurely under PF VLAN management.
So to resolve, we must check the VLAN update action type before exiting
fm10k_update_vid(), and act appropriately based on the action type.
Also corrected code comment typos.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ngai-Mint Kwan [Wed, 24 Jan 2018 22:23:27 +0000 (14:23 -0800)]
fm10k: clarify action when updating the VLAN table
Clarify the comment for when entering promiscuous mode that we update
the VLAN table. Add a comment distinguishing the case where we're
exiting promiscuous mode and need to clear the entire VLAN table.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@gmail.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ngai-Mint Kwan [Wed, 24 Jan 2018 22:22:18 +0000 (14:22 -0800)]
fm10k: correct typo in fm10k_pf.c
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 24 Jan 2018 22:20:29 +0000 (14:20 -0800)]
fm10k: don't assume VLAN 1 is enabled
Since commit
856dfd69e84f ("fm10k: Fix multicast mode synch issues",
2016-03-03) we've incorrectly assumed that VLAN 1 is enabled when the
default VID is not set.
This occurs because we check the default_vid and if it's zero, start
several loops over the active_vlans bitmask at 1, instead of checking to
ensure that that bit is active.
This happened because of commit
d9ff3ee8efe9 ("fm10k: Add support for
VLAN 0 w/o default VLAN", 2014-08-07) which mistakenly assumed that we
should send requests for MAC and VLAN filters with VLAN 0 when the
default_vid isn't set.
However, the switch generally considers this an invalid configuration,
so the only time we'd have a default_vid of 0 is when the switch is
down.
Instead, lets just not request any filters for the default_vid if it's
not yet been assigned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 24 Jan 2018 22:19:30 +0000 (14:19 -0800)]
fm10k: stop adding VLAN 0 to the VLAN table
Currently, when the driver loads, it sends a request to add VLAN 0 to the
VLAN table. For the PF, this is honored, and VLAN 0 is indeed set. For
the VF, this request is silently converted into a request for the
default VLAN as defined by either the switch vid or the PF vid.
This results in the odd behavior that the VLAN table doesn't appear
consistent between the PF and the VF.
Furthermore, setting a MAC filter with VLAN 0 is generally considered an
invalid configuration by the switch, and since commit
856dfd69e84f
("fm10k: Fix multicast mode synch issues", 2016-03-03) we've had code
which prevents us from ever sending such a request.
Since there's not really a good reason to keep VLAN 0 in the VLAN table,
stop requesting it in fm10k_restore_rx_state().
This might seem to indicate that we would no longer properly configure
the MAC and VLAN tables for the default vid. However, due to the way
that fm10k_find_next_vlan() behaves, it will always return the
default_vid as enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ngai-Mint Kwan [Wed, 24 Jan 2018 22:18:22 +0000 (14:18 -0800)]
fm10k: fix "failed to kill vid" message for VF
When a VF is under PF VLAN assignment:
ip link set <pf> vf <#> vlan <vid>
This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":
failed to kill vid 0081/<vid> for device <vf>
This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.
Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.
The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.
However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 24 Jan 2018 22:17:15 +0000 (14:17 -0800)]
fm10k: cleanup unnecessary parenthesis in fm10k_iov.c
This fixes a few warnings found by checkpatch.pl --strict
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wei Yongjun [Wed, 24 Jan 2018 02:14:33 +0000 (02:14 +0000)]
cxgb4: make symbol pedits static
Fixes the following sparse warning:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_flower.c:46:27: warning:
symbol 'pedits' was not declared. Should it be static?
Fixes:
27ece1f357b7 ("cxgb4: add tc flower support for ETH-DMAC rewrite")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 23 Jan 2018 09:27:26 +0000 (17:27 +0800)]
vhost: do not try to access device IOTLB when not initialized
The code will try to access dev->iotlb when processing
VHOST_IOTLB_INVALIDATE even if it was not initialized which may lead
to NULL pointer dereference. Fixes this by check dev->iotlb before.
Fixes:
6b1e6cc7855b0 ("vhost: new device IOTLB API")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 23 Jan 2018 09:27:25 +0000 (17:27 +0800)]
vhost: use mutex_lock_nested() in vhost_dev_lock_vqs()
We used to call mutex_lock() in vhost_dev_lock_vqs() which tries to
hold mutexes of all virtqueues. This may confuse lockdep to report a
possible deadlock because of trying to hold locks belong to same
class. Switch to use mutex_lock_nested() to avoid false positive.
Fixes:
6b1e6cc7855b0 ("vhost: new device IOTLB API")
Reported-by: syzbot+dbb7c1161485e61b0241@syzkaller.appspotmail.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Wed, 24 Jan 2018 01:01:29 +0000 (17:01 -0800)]
net: erspan: fix use-after-free
When building the erspan header for either v1 or v2, the eth_hdr()
does not point to the right inner packet's eth_hdr,
causing kasan report use-after-free and slab-out-of-bouds read.
The patch fixes the following syzkaller issues:
[1] BUG: KASAN: slab-out-of-bounds in erspan_xmit+0x22d4/0x2430 net/ipv4/ip_gre.c:735
[2] BUG: KASAN: slab-out-of-bounds in erspan_build_header+0x3bf/0x3d0 net/ipv4/ip_gre.c:698
[3] BUG: KASAN: use-after-free in erspan_xmit+0x22d4/0x2430 net/ipv4/ip_gre.c:735
[4] BUG: KASAN: use-after-free in erspan_build_header+0x3bf/0x3d0 net/ipv4/ip_gre.c:698
[2] CPU: 0 PID: 3654 Comm: syzkaller377964 Not tainted 4.15.0-rc9+ #185
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x25b/0x340 mm/kasan/report.c:409
__asan_report_load_n_noabort+0xf/0x20 mm/kasan/report.c:440
erspan_build_header+0x3bf/0x3d0 net/ipv4/ip_gre.c:698
erspan_xmit+0x3b8/0x13b0 net/ipv4/ip_gre.c:740
__netdev_start_xmit include/linux/netdevice.h:4042 [inline]
netdev_start_xmit include/linux/netdevice.h:4051 [inline]
packet_direct_xmit+0x315/0x6b0 net/packet/af_packet.c:266
packet_snd net/packet/af_packet.c:2943 [inline]
packet_sendmsg+0x3aed/0x60b0 net/packet/af_packet.c:2968
sock_sendmsg_nosec net/socket.c:638 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:648
SYSC_sendto+0x361/0x5c0 net/socket.c:1729
SyS_sendto+0x40/0x50 net/socket.c:1697
do_syscall_32_irqs_on arch/x86/entry/common.c:327 [inline]
do_fast_syscall_32+0x3ee/0xf9d arch/x86/entry/common.c:389
entry_SYSENTER_compat+0x54/0x63 arch/x86/entry/entry_64_compat.S:129
RIP: 0023:0xf7fcfc79
RSP: 002b:
00000000ffc6976c EFLAGS:
00000286 ORIG_RAX:
0000000000000171
RAX:
ffffffffffffffda RBX:
0000000000000004 RCX:
0000000020011000
RDX:
0000000000000000 RSI:
0000000000000000 RDI:
0000000020008000
RBP:
000000000000001c R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
0000000000000000
R13:
0000000000000000 R14:
0000000000000000 R15:
0000000000000000
Fixes:
f551c91de262 ("net: erspan: introduce erspan v2 for ip_gre")
Fixes:
84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Reported-by: syzbot+9723f2d288e49b492cf0@syzkaller.appspotmail.com
Reported-by: syzbot+f0ddeb2b032a8e1d9098@syzkaller.appspotmail.com
Reported-by: syzbot+f14b3703cd8d7670203f@syzkaller.appspotmail.com
Reported-by: syzbot+eefa384efad8d7997f20@syzkaller.appspotmail.com
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 23 Jan 2018 08:08:40 +0000 (00:08 -0800)]
i40e: flower: check if TC offload is enabled on a netdev
Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.
Fixes:
2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Fixes:
44ae12a768b7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corentin Labbe [Tue, 23 Jan 2018 14:33:14 +0000 (14:33 +0000)]
sparc64: fix typo in CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64
This patch fixes the typo CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64
Fixes:
81658ad0d923 ("sparc64: Add CAMELLIA driver making use of the new camellia opcodes.")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 21:44:21 +0000 (16:44 -0500)]
Merge branch 'qed-rdma-bug-fixes'
Michal Kalderon says:
====================
qed: rdma bug fixes
This patch contains two small bug fixes related to RDMA.
Both related to resource reservations.
====================
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Tue, 23 Jan 2018 09:33:47 +0000 (11:33 +0200)]
qed: Free reserved MR tid
A tid was allocated for reserved MR during initialization but
not freed. This lead to an annoying output message during
rdma unload flow.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Tue, 23 Jan 2018 09:33:46 +0000 (11:33 +0200)]
qed: Remove reserveration of dpi for kernel
Double reservation for kernel dedicated dpi was performed.
Once in the core module and once in qedr.
Remove the reservation from core.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 24 Jan 2018 21:39:44 +0000 (13:39 -0800)]
fm10k: Fix configuration for macvlan offload
The fm10k driver didn't work correctly when macvlan offload was enabled.
Specifically what would occur is that we would see no unicast packets being
received. This was traced down to us not correctly configuring the default
VLAN ID for the port and defaulting to 0.
To correct this we either use the default ID provided by the switch or
simply use 1. With that we are able to pass and receive traffic without any
issues.
In addition we were not repopulating the filter table following a reset. To
correct that I have added a bit of code to fm10k_restore_rx_state that will
repopulate the Rx filter configuration for the macvlan interfaces.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wang Dongsheng [Tue, 23 Jan 2018 04:25:06 +0000 (20:25 -0800)]
net: qcom/emac: extend DMA mask to 46bits
Bit TPD3[31] is used as a timestamp bit if PTP is enabled, but
it's used as an address bit if PTP is disabled. Since PTP isn't
supported by the driver, we can extend the DMA address to 46 bits.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Winter [Tue, 23 Jan 2018 03:46:24 +0000 (16:46 +1300)]
ip_tunnel: Use mark in skb by default
This allows marks set by connmark in iptables
to be used for route lookups.
Signed-off-by: Thomas Winter <thomas.winter@alliedtelesis.co.nz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Mon, 22 Jan 2018 15:59:50 +0000 (16:59 +0100)]
net: stmmac: do not use a bitwise AND operator with a bool operand
Doing a bitwise AND between a bool and an int is generally not a good idea.
The bool will be promoted to an int with value 0 or 1,
the int is generally regarded as true with a non-zero value,
thus ANDing them has the potential to yield an undesired result.
This commit fixes the following smatch warnings:
drivers/net/ethernet/stmicro/stmmac/enh_desc.c:344 enh_desc_prepare_tx_desc() warn: maybe use && instead of &
drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c:337 dwmac4_rd_prepare_tx_desc() warn: maybe use && instead of &
drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c:380 dwmac4_rd_prepare_tso_tx_desc() warn: maybe use && instead of &
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 21:09:09 +0000 (16:09 -0500)]
Merge branch '1GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2018-01-24
This series contains updates to igb and e1000e only.
Corinna Vinschen implements the ability to set the VF MAC to
00:00:00:00:00:00 via RTM_SETLINK on the PF, to prevent receiving
"invlaid argument" when libvirt attempts to restore the MAC address back
to its original state of 00:00:00:00:00:00.
Zhang Shengju adds a new function igb_get_max_rss_queues() to get the
maxium number of RSS queues and to reduce code duplication.
Matt fixes an issue with e1000e where when setting HTHREST, we should
only be setting bit 8. Also added a dev_info() message to alert when
C-states have been disabled, to help in debugging.
Jesus adds code comments to clarify the idlescope configuration
constraints.
Lyude Paul fixes a kernel crash on hotplug of igb, by checking to ensure
that we are in the process of dismantling the netdev on hotplug events.
Markus Elfring removes a duplicate message for a memory allocation
failure.
Daniel Hua fixes an issue where transmit timestamps will stop being put
into the socket when link is repeatedly up/down due to TSYNCTXCTL's TXTT
bit (Transmit timestamp valid bit) not clearing in the timeout logic of
ptp_tx_work(), which in turn causes no new timestamp to be loaded to the
TXSTMP register.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 21:01:11 +0000 (16:01 -0500)]
Merge branch 'net-sched-propagate-extack-to-cls-offloads-on-destroy-and-only-with-skip_sw'
Jakub Kicinski says:
====================
net: sched: propagate extack to cls offloads on destroy and only with skip_sw
This series some of Jiri's comments and the fact that today drivers
may produce extack even if there is no skip_sw flag (meaning the
driver failure is not really a problem), and warning messages will
only confuse the users.
First patch propagates extack to destroy as requested by Jiri, extack
is then propagated to the driver callback for each classifier. I chose
not to provide the extack on error paths. As a rule of thumb it seems
best to keep the extack of the condition which caused the error. E.g.
err = this_will_fail(arg, extack);
if (err) {
undo_things(arg, NULL /* don't pass extack */);
return err;
}
Note that NL_SET_ERR_MSG() will ignore the message if extack is NULL.
I was pondering whether we should make NL_SET_ERR_MSG() refuse to
overwrite the msg, but there seem to be cases in the tree where extack
is set like this:
err = this_will_fail(arg, extack);
if (err) {
undo_things(arg, NULL /* don't pass extack */);
NL_SET_ERR_MSG(extack, "extack is set after undo call :/");
return err;
}
I think not passing extack to undo calls is reasonable.
v2:
- rename the temporary tc_cls_common_offload_init().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:24 +0000 (12:54 -0800)]
net: sched: remove tc_cls_common_offload_init_deprecated()
All users are now converted to tc_cls_common_offload_init().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:23 +0000 (12:54 -0800)]
cls_u32: propagate extack to delete callback
Propagate extack on removal of offloaded filter. Don't pass
extack from error paths.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:22 +0000 (12:54 -0800)]
cls_u32: pass offload flags to tc_cls_common_offload_init()
Pass offload flags to the new implementation of
tc_cls_common_offload_init(). Extack will now only
be set if user requested skip_sw. hnodes need to
hold onto the flags now to be able to reuse them
on filter removal.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:21 +0000 (12:54 -0800)]
cls_flower: propagate extack to delete callback
Propagate extack on removal of offloaded filter. Don't pass
extack from error paths.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:20 +0000 (12:54 -0800)]
cls_flower: pass offload flags to tc_cls_common_offload_init()
Pass offload flags to the new implementation of
tc_cls_common_offload_init(). Extack will now only
be set if user requested skip_sw.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:19 +0000 (12:54 -0800)]
cls_matchall: propagate extack to delete callback
Propagate extack on removal of offloaded filter. Don't pass
extack from error paths.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:18 +0000 (12:54 -0800)]
cls_matchall: pass offload flags to tc_cls_common_offload_init()
Pass offload flags to the new implementation of
tc_cls_common_offload_init(). Extack will now only
be set if user requested skip_sw.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:17 +0000 (12:54 -0800)]
cls_bpf: propagate extack to offload delete callback
Propagate extack on removal of offloaded filter.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:16 +0000 (12:54 -0800)]
cls_bpf: pass offload flags to tc_cls_common_offload_init()
Pass offload flags to the new implementation of
tc_cls_common_offload_init(). Extack will now only
be set if user requested skip_sw.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:15 +0000 (12:54 -0800)]
cls_bpf: remove gen_flags from bpf_offload
cls_bpf now guarantees that only device-bound programs are
allowed with skip_sw. The drivers no longer pay attention to
flags on filter load, therefore the bpf_offload member can be
removed. If flags are needed again they should probably be
added to struct tc_cls_common_offload instead.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:14 +0000 (12:54 -0800)]
net: sched: prepare for reimplementation of tc_cls_common_offload_init()
Rename the tc_cls_common_offload_init() helper function to
tc_cls_common_offload_init_deprecated() and add a new implementation
which also takes flags argument. We will only set extack if flags
indicate that offload is forced (skip_sw) otherwise driver errors
should be ignored, as they don't influence the overall filter
installation.
Note that we need the tc_skip_hw() helper for new version, therefore
it is added later in the file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 24 Jan 2018 20:54:13 +0000 (12:54 -0800)]
net: sched: propagate extack to cls->destroy callbacks
Propagate extack to cls->destroy callbacks when called from
non-error paths. On error paths pass NULL to avoid overwriting
the failure message.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 20:54:31 +0000 (15:54 -0500)]
Merge branch 'kcm-fix-two-syzcaller-issues'
Tom Herbert says:
====================
kcm: fix two syzcaller issues
In this patch set:
- Don't allow attaching non-TCP or listener sockets to a KCM mux.
- In kcm_attach Check if sk_user_data is already set. This is
under lock to avoid race conditions. More work is need to make
all of the users of sk_user_data to use the same locking.
- v2
Remove unncessary check for not PF_KCM in kcm_attach (suggested by
Guillaume Nault)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 24 Jan 2018 20:35:41 +0000 (12:35 -0800)]
kcm: Check if sk_user_data already set in kcm_attach
This is needed to prevent sk_user_data being overwritten.
The check is done under the callback lock. This should prevent
a socket from being attached twice to a KCM mux. It also prevents
a socket from being attached for other use cases of sk_user_data
as long as the other cases set sk_user_data under the lock.
Followup work is needed to unify all the use cases of sk_user_data
to use the same locking.
Reported-by: syzbot+114b15f2be420a8886c3@syzkaller.appspotmail.com
Fixes:
ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: Tom Herbert <tom@quantonium.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 24 Jan 2018 20:35:40 +0000 (12:35 -0800)]
kcm: Only allow TCP sockets to be attached to a KCM mux
TCP sockets for IPv4 and IPv6 that are not listeners or in closed
stated are allowed to be attached to a KCM mux.
Fixes:
ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+8865eaff7f9acd593945@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
James Morris [Wed, 24 Jan 2018 20:53:57 +0000 (07:53 +1100)]
MAINTAINERS: update email address for James Morris
Update my email address.
Signed-off-by: James Morris <jmorris@namei.org>
Daniel Hua [Tue, 2 Jan 2018 00:33:18 +0000 (08:33 +0800)]
igb: Clear TXSTMP when ptp_tx_work() is timeout
Problem description:
After ethernet cable connect and disconnect for several iterations on a
device with i210, tx timestamp will stop being put into the socket.
Steps to reproduce:
1. Setup a device with i210 and wire it to a 802.1AS capable switch (
Extreme Networks Summit x440 is used in our case)
2. Have the gptp daemon running on the device and make sure it is synced
with the switch
3. Have the switch disable and enable the port, wait for the device gets
resynced with the switch
4. Iterates step 3 until the device is not albe to get resynced
5. Review the log in dmesg and you will see warning message "igb : clearing
Tx timestamp hang"
Root cause:
If ptp_tx_work() gets scheduled just before the port gets disabled, a LINK
DOWN event will be processed before ptp_tx_work(), which may cause timeout
in ptp_tx_work(). In the timeout logic, the TSYNCTXCTL's TXTT bit (Transmit
timestamp valid bit) is not cleared, causing no new timestamp loaded to
TXSTMP register. Consequently therefore, no new interrupt is triggerred by
TSICR.TXTS bit and no more Tx timestamp send to the socket.
Signed-off-by: Daniel Hua <daniel.hua@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Markus Elfring [Mon, 1 Jan 2018 19:56:55 +0000 (20:56 +0100)]
igb: Delete an error message for a failed memory allocation in igb_enable_sriov()
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lyude Paul [Tue, 12 Dec 2017 19:31:30 +0000 (14:31 -0500)]
igb: Free IRQs when device is hotplugged
Recently I got a Caldigit TS3 Thunderbolt 3 dock, and noticed that upon
hotplugging my kernel would immediately crash due to igb:
[ 680.825801] kernel BUG at drivers/pci/msi.c:352!
[ 680.828388] invalid opcode: 0000 [#1] SMP
[ 680.829194] Modules linked in: igb(O) thunderbolt i2c_algo_bit joydev vfat fat btusb btrtl btbcm btintel bluetooth ecdh_generic hp_wmi sparse_keymap rfkill wmi_bmof iTCO_wdt intel_rapl x86_pkg_temp_thermal coretemp crc32_pclmul snd_pcm rtsx_pci_ms mei_me snd_timer memstick snd pcspkr mei soundcore i2c_i801 tpm_tis psmouse shpchp wmi tpm_tis_core tpm video hp_wireless acpi_pad rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci mfd_core xhci_pci xhci_hcd i2c_hid i2c_core [last unloaded: igb]
[ 680.831085] CPU: 1 PID: 78 Comm: kworker/u16:1 Tainted: G O 4.15.0-rc3Lyude-Test+ #6
[ 680.831596] Hardware name: HP HP ZBook Studio G4/826B, BIOS P71 Ver. 01.03 06/09/2017
[ 680.832168] Workqueue: kacpi_hotplug acpi_hotplug_work_fn
[ 680.832687] RIP: 0010:free_msi_irqs+0x180/0x1b0
[ 680.833271] RSP: 0018:
ffffc9000030fbf0 EFLAGS:
00010286
[ 680.833761] RAX:
ffff8803405f9c00 RBX:
ffff88033e3d2e40 RCX:
000000000000002c
[ 680.834278] RDX:
0000000000000000 RSI:
00000000000000ac RDI:
ffff880340be2178
[ 680.834832] RBP:
0000000000000000 R08:
ffff880340be1ff0 R09:
ffff8803405f9c00
[ 680.835342] R10:
0000000000000000 R11:
0000000000000040 R12:
ffff88033d63a298
[ 680.835822] R13:
ffff88033d63a000 R14:
0000000000000060 R15:
ffff880341959000
[ 680.836332] FS:
0000000000000000(0000) GS:
ffff88034f440000(0000) knlGS:
0000000000000000
[ 680.836817] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 680.837360] CR2:
000055e64044afdf CR3:
0000000001c09002 CR4:
00000000003606e0
[ 680.837954] Call Trace:
[ 680.838853] pci_disable_msix+0xce/0xf0
[ 680.839616] igb_reset_interrupt_capability+0x5d/0x60 [igb]
[ 680.840278] igb_remove+0x9d/0x110 [igb]
[ 680.840764] pci_device_remove+0x36/0xb0
[ 680.841279] device_release_driver_internal+0x157/0x220
[ 680.841739] pci_stop_bus_device+0x7d/0xa0
[ 680.842255] pci_stop_bus_device+0x2b/0xa0
[ 680.842722] pci_stop_bus_device+0x3d/0xa0
[ 680.843189] pci_stop_and_remove_bus_device+0xe/0x20
[ 680.843627] trim_stale_devices+0xf3/0x140
[ 680.844086] trim_stale_devices+0x94/0x140
[ 680.844532] trim_stale_devices+0xa6/0x140
[ 680.845031] ? get_slot_status+0x90/0xc0
[ 680.845536] acpiphp_check_bridge.part.5+0xfe/0x140
[ 680.846021] acpiphp_hotplug_notify+0x175/0x200
[ 680.846581] ? free_bridge+0x100/0x100
[ 680.847113] acpi_device_hotplug+0x8a/0x490
[ 680.847535] acpi_hotplug_work_fn+0x1a/0x30
[ 680.848076] process_one_work+0x182/0x3a0
[ 680.848543] worker_thread+0x2e/0x380
[ 680.848963] ? process_one_work+0x3a0/0x3a0
[ 680.849373] kthread+0x111/0x130
[ 680.849776] ? kthread_create_worker_on_cpu+0x50/0x50
[ 680.850188] ret_from_fork+0x1f/0x30
[ 680.850601] Code: 43 14 85 c0 0f 84 d5 fe ff ff 31 ed eb 0f 83 c5 01 39 6b 14 0f 86 c5 fe ff ff 8b 7b 10 01 ef e8 b7 e4 d2 ff 48 83 78 70 00 74 e3 <0f> 0b 49 8d b5 a0 00 00 00 e8 62 6f d3 ff e9 c7 fe ff ff 48 8b
[ 680.851497] RIP: free_msi_irqs+0x180/0x1b0 RSP:
ffffc9000030fbf0
As it turns out, normally the freeing of IRQs that would fix this is called
inside of the scope of __igb_close(). However, since the device is
already gone by the point we try to unregister the netdevice from the
driver due to a hotplug we end up seeing that the netif isn't present
and thus, forget to free any of the device IRQs.
So: make sure that if we're in the process of dismantling the netdev, we
always allow __igb_close() to be called so that IRQs may be freed
normally. Additionally, only allow igb_close() to be called from
__igb_close() if it hasn't already been called for the given adapter.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes:
9474933caf21 ("igb: close/suspend race in netif_device_detach")
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: stable@vger.kernel.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matt Turner [Tue, 14 Nov 2017 23:51:33 +0000 (15:51 -0800)]
e1000e: Alert the user that C-states will be disabled by enabling jumbo frames
I personally spent a long time trying to decypher why my CPU would not
reach deeper C-states. Let's just tell the next user what's going on.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesus Sanchez-Palencia [Fri, 10 Nov 2017 22:21:50 +0000 (14:21 -0800)]
igb: Clarify idleslope config constraints
By design, the idleslope increments are restricted to 16.384kbps steps.
Add a comment to igb_main.c making that explicit and add one example
that illustrates the impact of that.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matt Turner [Tue, 7 Nov 2017 22:13:30 +0000 (14:13 -0800)]
e1000e: Set HTHRESH when PTHRESH is used
According to section 12.0.3.4.13 "Receive Descriptor Control - RXDCTL"
of the Intel® 82579 Gigabit Ethernet PHY Datasheet v2.1:
"HTHRESH should be given a non zero value when ever PTHRESH is
used."
In RXDCTL(0), PTHRESH lives at bits 5:0, and HTHREST lives at bits 13:8.
Set only bit 8 of HTHREST as is done in e1000_flush_rx_ring(). Found by
inspection.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Zhang Shengju [Tue, 19 Sep 2017 13:40:54 +0000 (21:40 +0800)]
igb: add function to get maximum RSS queues
This patch adds a new function igb_get_max_rss_queues() to get maximum
RSS queues, this will reduce duplicate code and facilitate future
maintenance.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Corinna Vinschen [Mon, 10 Apr 2017 08:58:14 +0000 (10:58 +0200)]
igb: Allow to remove administratively set MAC on VFs
Before libvirt modifies the MAC address and vlan tag for an SRIOV VF
for use by a virtual machine (either using vfio device assignment or
macvtap passthru mode), it saves the current MAC address and vlan tag
so that it can reset them to their original value when the guest is
done. Libvirt can't leave the VF MAC set to the value used by the
now-defunct guest since it may be started again later using a
different VF, but it certainly shouldn't just pick any random value,
either. So it saves the state of everything prior to using the VF, and
resets it to that.
The igb driver initializes the MAC addresses of all VFs to
00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK
netlink message, also visible in the list of VFs in the output of "ip
link show"). But when libvirt attempts to restore the MAC address back
to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel
responds with "Invalid argument".
Forbidding a reset back to the original value leaves the VF MAC at the
value set for the now-defunct virtual machine. Especially on a system
with NetworkManager enabled, this has very bad consequences, since
NetworkManager forces all interfacess to be IFF_UP all the time - if
the same virtual machine is restarted using a different VF (or even on
a different host), there will be multiple interfaces watching for
traffic with the same MAC address.
To allow libvirt to revert to the original state, we need a way to
remove the administrative set MAC on a VF, to allow normal host
operation again, and to reset/overwrite the VF MAC via VF netdev.
This patch implements the outlined scenario by allowing to set the
VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF.
igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0,
so it's possible to reset the VF MAC back to the original value via
the VF netdev.
Note: Recent patches to libvirt allow for a workaround if the NIC
isn't capable of resetting the administrative MAC back to all 0, but
in theory the NIC should allow resetting the MAC in the first place.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <arron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Wed, 24 Jan 2018 20:03:37 +0000 (15:03 -0500)]
Merge branch 'pktgen-Behavior-flags-fixes'
Dmitry Safonov says:
====================
pktgen: Behavior flags fixes
v2:
o fixed a nitpick from David Miller
There are a bunch of fixes/cleanups/Documentations.
Diffstat says for itself, regardless added docs and missed flag
parameters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Safonov [Thu, 18 Jan 2018 18:31:37 +0000 (18:31 +0000)]
pktgen: Clean read user supplied flag mess
Don't use error-prone-brute-force way.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Safonov [Thu, 18 Jan 2018 18:31:36 +0000 (18:31 +0000)]
pktgen: Remove brute-force printing of flags
Add macro generated pkt_flag_names array, with a little help of which
the flags can be printed by using an index.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Safonov [Thu, 18 Jan 2018 18:31:35 +0000 (18:31 +0000)]
pktgen: Add behaviour flags macro to generate flags/names
PKT_FALGS macro will be used to add package behavior names definitions
to simplify the code that prints/reads pkg flags.
Sorted the array in order of printing the flags in pktgen_if_show()
Note: Renamed IPSEC_ON => IPSEC for simplicity.
No visible behavior change expected.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Safonov [Thu, 18 Jan 2018 18:31:34 +0000 (18:31 +0000)]
pktgen: Add missing !flag parameters
o FLOW_SEQ now can be disabled with pgset "flag !FLOW_SEQ"
o FLOW_SEQ and FLOW_RND are antonyms, as it's shown by pktgen_if_show()
o IPSEC now may be disabled
Note, that IPV6 is enabled with dst6/src6 parameters, not with
a flag parameter.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Safonov [Thu, 18 Jan 2018 18:31:33 +0000 (18:31 +0000)]
Documentation/pktgen: Clearify how-to use pktgen samples
o Change process name in ps output: looks like, these days the process
is named kpktgend_<cpu>, rather than pktgen/<cpu>.
o Use pg_ctrl for start/stop as it can work well with pgset without
changes to $(PGDEV) variable.
o Clarify a bit needed $(PGDEV) definition for sample scripts and that
one needs to `source functions.sh`.
o Document how-to unset a behaviour flag, note about history expansion.
o Fix pgset spi parameter value.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfgang Bumiller [Thu, 18 Jan 2018 10:32:36 +0000 (11:32 +0100)]
net: sched: fix TCF_LAYER_LINK case in tcf_get_base_ptr
TCF_LAYER_LINK and TCF_LAYER_NETWORK returned the same pointer as
skb->data points to the network header.
Use skb_mac_header instead.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfgang Bumiller [Thu, 18 Jan 2018 10:32:35 +0000 (11:32 +0100)]
net: sched: em_nbyte: don't add the data offset twice
'ptr' is shifted by the offset and then validated,
the memcmp should not add it a second time.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 24 Jan 2018 18:08:16 +0000 (10:08 -0800)]
Merge tag 'trace-v4.15-rc9' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"With the new ORC unwinder, ftrace stack tracing became disfunctional.
One was that ORC didn't know how to handle the ftrace callbacks in
general (which Josh fixed).
The other was that ORC would just bail if it hit a dynamically
allocated trampoline. Which means all ftrace stack tracing that
happens from the function tracer would produce no results (that
includes killing the max stack size tracer). I added a check to the
ORC unwinder to see if the trampoline belonged to ftrace, and if it
did, use the orc entry of the static trampoline that was used to
create the dynamic one (it would be identical).
Finally, I noticed that the skip values of the stack tracing were out
of whack. I went through and fixed them up"
* tag 'trace-v4.15-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Update stack trace skipping for ORC unwinder
ftrace, orc, x86: Handle ftrace dynamically allocated trampolines
x86/ftrace: Fix ORC unwinding from ftrace handlers
Willy Tarreau [Thu, 4 Jan 2018 13:31:25 +0000 (14:31 +0100)]
MAINTAINERS: clarify that only verified bugs should be submitted to security@
We're seeing a raise of automated reports from testing tools and reports
about address leaks that are not really exploitable as-is, many of which
do not represent an immediate risk justifying to work in closed places.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Kroah-Hartman [Wed, 24 Jan 2018 14:28:17 +0000 (15:28 +0100)]
Revert "module: Add retpoline tag to VERMAGIC"
This reverts commit
6cfb521ac0d5b97470883ff9b7facae264b7ab12.
Turns out distros do not want to make retpoline as part of their "ABI",
so this patch should not have been merged. Sorry Andi, this was my
fault, I suggested it when your original patch was the "correct" way of
doing this instead.
Reported-by: Jiri Kosina <jikos@kernel.org>
Fixes:
6cfb521ac0d5 ("module: Add retpoline tag to VERMAGIC")
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: rusty@rustcorp.com.au
Cc: arjan.van.de.ven@intel.com
Cc: jeyu@kernel.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yuval Mintz [Wed, 24 Jan 2018 09:02:09 +0000 (10:02 +0100)]
mlxsw: spectrum_router: Don't log an error on missing neighbor
Driver periodically samples all neighbors configured in device
in order to update the kernel regarding their state. When finding
an entry configured in HW that doesn't show in neigh_lookup()
driver logs an error message.
This introduces a race when removing multiple neighbors -
it's possible that a given entry would still be configured in HW
as its removal is still being processed but is already removed
from the kernel's neighbor tables.
Simply remove the error message and gracefully accept such events.
Fixes:
c723c735fa6b ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Fixes:
60f040ca11b9 ("mlxsw: spectrum_router: Periodically dump active IPv6 neighbours")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 15:56:59 +0000 (10:56 -0500)]
Merge branch 'cxgb4-fix-build-error'
Rahul Lakkireddy says:
====================
cxgb4: fix build error
Patch 1 fixes build error with compiling cudbg_zlib.c when
CONFIG_ZLIB_DEFLATE macro is not defined.
Patch 2 fixes following sparse warning:
"Using plain integer as NULL pointer"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Wed, 24 Jan 2018 08:01:05 +0000 (13:31 +0530)]
cxgb4: properly initialize variables
memset variables to 0 to fix sparse warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_cudbg.c:409:42: sparse: Using
plain integer as NULL pointer
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:43:47: sparse: Using
plain integer as NULL pointer
Fixes:
ad75b7d32f25 ("cxgb4: implement ethtool dump data operations")
Fixes:
91c1953de387 ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy [Wed, 24 Jan 2018 08:01:04 +0000 (13:31 +0530)]
cxgb4: enable ZLIB_DEFLATE when building cxgb4
Fixes:
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:39:5: error:
redefinition of 'cudbg_compress_buff'
int cudbg_compress_buff(struct cudbg_init *pdbg_init,
^~~~~~~~~~~~~~~~~~~
In file included from
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:23:0:
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.h:45:19: note: previous
definition of 'cudbg_compress_buff' was here
static inline int cudbg_compress_buff(struct cudbg_init *pdbg_init,
^~~~~~~~~~~~~~~~~~~
Fixes:
91c1953de387 ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 15:52:58 +0000 (10:52 -0500)]
Merge branch 'net-smc-socket-closing-improvements'
Ursula Braun says:
====================
net/smc: socket closing improvements
while the first 2 patches are just small cleanups, the remaing
patches affect socket closing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 24 Jan 2018 09:28:17 +0000 (10:28 +0100)]
net/smc: continue waiting if peer signals write_shutdown
If the peer sends a shutdown WRITE, this should not affect sending
in general, and waiting for send buffer space in particular.
Stop waiting of the local socket for send buffer space only, if peer
signals closing, but not if peer signals just shutdown WRITE.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 24 Jan 2018 09:28:16 +0000 (10:28 +0100)]
net/smc: improve state change handling after close wait
When a socket is closed or shutdown, smc waits for data being transmitted
in certain states. If the state changes during this wait, the close
switch depending on state should be reentered.
In addition, state change is avoided if sending of close or shutdown fails.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 24 Jan 2018 09:28:15 +0000 (10:28 +0100)]
net/smc: make wait for work request uninterruptible
Work requests are needed for every ib_post_send(), among them the
ib_post_send() to signal closing. If an smc socket program is cancelled,
the smc connections should be cleaned up, and require sending of closing
signals to the peer. This may fail, if a wait for
a free work request is needed, but is cancelled immediately due to the
cancel interrupt. To guarantee notification of the peer, the wait for
a work request is changed to uninterruptible.
And the area to receive work request completion info with
ib_poll_cq() is cleared first.
And _tx_ variable names are used in the _tx_routines for the
demultiplexing common type in the header.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 24 Jan 2018 09:28:14 +0000 (10:28 +0100)]
net/smc: get rid of tx_pend waits in socket closing
There is no need to wait for confirmation of pending tx requests
for a closing connection, since pending tx slots are dismissed
when finishing a connection.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 24 Jan 2018 09:28:13 +0000 (10:28 +0100)]
net/smc: simplify function smc_clcsock_accept()
Cleanup to avoid duplicate code in smc_clcsock_accept().
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 24 Jan 2018 09:28:12 +0000 (10:28 +0100)]
net/smc: use local struct sock variables consistently
Cleanup to consistently exploit the local struct sock definitions.
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Wed, 24 Jan 2018 15:14:07 +0000 (20:44 +0530)]
cxgb4/cxgb4vf: add support for ndo_set_vf_vlan
implement ndo_set_vf_vlan for mgmt netdevice to configure
the PCIe VF.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 15:32:29 +0000 (10:32 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2018-01-24
1) Only offloads SAs after they are fully initialized.
Otherwise a NIC may receive packets on a SA we can
not yet handle in the stack.
From Yossi Kuperman.
2) Fix negative refcount in case of a failing offload.
From Aviad Yehezkel.
3) Fix inner IP ptoro version when decapsulating
from interaddress family tunnels.
From Yossi Kuperman.
4) Use true or false for boolean variables instead of an
integer value in xfrm_get_type_offload.
From Gustavo A. R. Silva.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 01:24:32 +0000 (20:24 -0500)]
Merge branch 'bpf-and-netdevsim-test-updates'
Jakub Kicinski says:
====================
bpf and netdevsim test updates
A number of test improvements (delayed by merges). Quentin provides
patches for checking printing to the verifier log from the drivers
and validating extack messages are propagated. There is also a test
for replacing TC filters to avoid adding back the bug Daniel recently
fixed in net and stable.
====================
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 23 Jan 2018 19:22:56 +0000 (11:22 -0800)]
selftests/bpf: validate replace of TC filters is working
Daniel discovered recently I broke TC filter replace (and fixed
it in commit
ad9294dbc227 ("bpf: fix cls_bpf on filter replace")).
Add a test to make sure it never happens again.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Tue, 23 Jan 2018 19:22:55 +0000 (11:22 -0800)]
selftests/bpf: check bpf verifier log buffer usage works for HW offload
Make netdevsim print a message to the BPF verifier log buffer when a
program is offloaded.
Then use this message in hardware offload selftests to make sure that
using this buffer actually prints the message to the console for
eBPF hardware offload.
The message is appended after the last instruction is processed with the
verifying function from netdevsim. Output looks like the following:
$ tc filter add dev foo ingress bpf obj sample_ret0.o \
sec .text verbose skip_sw
Prog section '.text' loaded (5)!
- Type: 3
- Instructions: 2 (0 over limit)
- License:
Verifier analysis:
0: (b7) r0 = 0
1: (95) exit
[netdevsim] Hello from netdevsim!
processed 2 insns, stack depth 0
"verbose" flag is required to see it in the console since netdevsim does
not throw an error after printing the message.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 23 Jan 2018 19:22:54 +0000 (11:22 -0800)]
netdevsim: don't compile BPF code if syscall not enabled
We should not compile netdevsim/bpf.c if BPF syscall is not
enabled. Otherwise bpf core would have to provide wrappers
for all functions offload drivers may call, even though
system will never see a BPF object.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Tue, 23 Jan 2018 19:22:53 +0000 (11:22 -0800)]
selftests/bpf: add checks on extack messages for eBPF hw offload tests
Add checks to test that netlink extack messages are correctly displayed
in some expected error cases for eBPF offload to netdevsim with TC and
XDP.
iproute2 may be built without libmnl support, in which case the extack
messages will not be reported. Try to detect this condition, and when
enountered print a mild warning to the user and skip the extack validation.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Monnet [Tue, 23 Jan 2018 19:22:52 +0000 (11:22 -0800)]
netdevsim: add extack support for TC eBPF offload
Use the recently added extack support for TC eBPF filters in netdevsim.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 01:22:57 +0000 (20:22 -0500)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-01-23
This series contains updates to i40e and i40evf only.
Pawel enables FlatNVM support on x722 devices by allowing nvmupdate tool
to configure the preservation flags in the AdminQ command.
Mitch fixes a potential divide by zero error when DCB is enabled and
the firmware fails to configure the VSI, so check for this state.
Fixed a bug where the driver could fail to adhere to ETS bandwidth
allocations if 8 traffic classes were configured on the switch.
Sudheer fixes a potential deadlock by avoiding to call
flush_schedule_work() in i40evf_remove(), since cancel_work_sync()
and cancel_delayed_work_sync() already cleans up necessary work items.
Fixed an issue with the problematic detection and recovery from
hung queues in the PF which was causing lost interrupts. This is done
by triggering a software interrupt so that interrupts are forced on
and if we are already in napi_poll and an interrupt fires, napi_poll
will not be rescheduled and the interrupt is lost.
Avinash fixes an issue in the VF where is was possible to issue a
reset_task while the device is currently being removed.
Michal fixes an issue occurring while calling i40e_led_set() with
the blink parameter set to true, which was causing the activity LED
instead of the link LED to blink for port identification.
Shiraz changes the client interface to not call client close/open on
netdev down/up events, since this causes a lot of thrash that is
not needed. Instead, disable the PE TCP-ENA flag during a netdev
down event and re-enable on a netdev up event, since this blocks all
TCP traffic to the RDMA protocol engine.
Alan fixes an issue which was causing a potential transmit hang by
ignoring the PF link up message if the VF state is not yet in the
RUNNING state.
Amritha fixes the channel VSI recreation during the reset flow to
reconfigure the transmit rings and the queue context associated with
the channel VSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Mon, 22 Jan 2018 21:06:37 +0000 (16:06 -0500)]
vmxnet3: repair memory leak
with the introduction of commit
b0eb57cb97e7837ebb746404c2c58c6f536f23fa, it appears that rq->buf_info
is improperly handled. While it is heap allocated when an rx queue is
setup, and freed when torn down, an old line of code in
vmxnet3_rq_destroy was not properly removed, leading to rq->buf_info[0]
being set to NULL prior to its being freed, causing a memory leak, which
eventually exhausts the system on repeated create/destroy operations
(for example, when the mtu of a vmxnet3 interface is changed
frequently.
Fix is pretty straight forward, just move the NULL set to after the
free.
Tested by myself with successful results
Applies to net, and should likely be queued for stable, please
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-By: boyang@redhat.com
CC: boyang@redhat.com
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: David S. Miller <davem@davemloft.net>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 22 Jan 2018 20:06:42 +0000 (20:06 +0000)]
ipv6: Fix getsockopt() for sockets with default IPV6_AUTOFLOWLABEL
Commit
513674b5a2c9 ("net: reevalulate autoflowlabel setting after
sysctl setting") removed the initialisation of
ipv6_pinfo::autoflowlabel and added a second flag to indicate
whether this field or the net namespace default should be used.
The getsockopt() handling for this case was not updated, so it
currently returns 0 for all sockets for which IPV6_AUTOFLOWLABEL is
not explicitly enabled. Fix it to return the effective value, whether
that has been set at the socket or net namespace level.
Fixes:
513674b5a2c9 ("net: reevalulate autoflowlabel setting after sysctl ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Jan 2018 00:51:46 +0000 (19:51 -0500)]
Merge branch 'act_csum-spinlock-remove'
Davide Caratti says:
====================
net/sched: remove spinlock from 'csum' action
Similarly to what has been done earlier with other actions [1][2], this
series tries to improve the performance of 'csum' tc action, removing a
spinlock in the data path. Patch 1 lets act_csum use per-CPU counters;
patch 2 removes spin_{,un}lock_bh() calls from the act() method.
test procedure (using pktgen from https://github.com/netoptimizer):
# ip link add name eth1 type dummy
# ip link set dev eth1 up
# tc qdisc add dev eth1 root handle 1: prio
# for a in pass drop; do
> tc filter del dev eth1 parent 1: pref 10 matchall action csum udp
> tc filter add dev eth1 parent 1: pref 10 matchall action csum udp $a
> for n in 2 4; do
> ./pktgen_bench_xmit_mode_queue_xmit.sh -v -s 64 -t $n -n
1000000 -i eth1
> done
> done
test results:
| | before patch | after patch
$a | $n | avg. pps/thread | avg. pps/thread
-----+----+-----------------+----------------
pass | 2 |
1671463 ± 4% |
1920789 ± 3%
pass | 4 | 648797 ± 1% | 738190 ± 1%
drop | 2 |
3212692 ± 2% |
3719811 ± 2%
drop | 4 |
1078824 ± 1% |
1328099 ± 1%
references:
[1] https://www.spinics.net/lists/netdev/msg334760.html
[2] https://www.spinics.net/lists/netdev/msg465862.html
v3 changes:
- use rtnl_dereference() in place of rcu_dereference() in tcf_csum_dump()
v2 changes:
- add 'drop' test, it produces more contentions
- use RCU-protected struct to store 'action' and 'update_flags', to avoid
reading the values from subsequent configurations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 22 Jan 2018 17:14:32 +0000 (18:14 +0100)]
net/sched: act_csum: don't use spinlock in the fast path
use RCU instead of spin_{,unlock}_bh() to protect concurrent read/write on
act_csum configuration, to reduce the effects of contention in the data
path when multiple readers are present.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Mon, 22 Jan 2018 17:14:31 +0000 (18:14 +0100)]
net/sched: act_csum: use per-core statistics
use per-CPU counters, like other TC actions do, instead of maintaining one
set of stats across all cores. This allows updating act_csum stats without
the need of protecting them using spin_{,un}lock_bh() invocations.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Mon, 22 Jan 2018 17:06:37 +0000 (18:06 +0100)]
pppoe: take ->needed_headroom of lower device into account on xmit
In pppoe_sendmsg(), reserving dev->hard_header_len bytes of headroom
was probably fine before the introduction of ->needed_headroom in
commit
f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom").
But now, virtual devices typically advertise the size of their overhead
in dev->needed_headroom, so we must also take it into account in
skb_reserve().
Allocation size of skb is also updated to take dev->needed_tailroom
into account and replace the arbitrary 32 bytes with the real size of
a PPPoE header.
This issue was discovered by syzbot, who connected a pppoe socket to a
gre device which had dev->header_ops->create == ipgre_header and
dev->hard_header_len == 0. Therefore, PPPoE didn't reserve any
headroom, and dev_hard_header() crashed when ipgre_header() tried to
prepend its header to skb->data.
skbuff: skb_under_panic: text:
000000001d390b3a len:31 put:24
head:
00000000d8ed776f data:
000000008150e823 tail:0x7 end:0xc0 dev:gre0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 3670 Comm: syzkaller801466 Not tainted
4.15.0-rc7-next-
20180115+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x162/0x1f0 net/core/skbuff.c:100
RSP: 0018:
ffff8801d9bd7840 EFLAGS:
00010282
RAX:
0000000000000083 RBX:
ffff8801d4f083c0 RCX:
0000000000000000
RDX:
0000000000000083 RSI:
1ffff1003b37ae92 RDI:
ffffed003b37aefc
RBP:
ffff8801d9bd78a8 R08:
1ffff1003b37ae8a R09:
0000000000000000
R10:
0000000000000001 R11:
0000000000000000 R12:
ffffffff86200de0
R13:
ffffffff84a981ad R14:
0000000000000018 R15:
ffff8801d2d34180
FS:
00000000019c4880(0000) GS:
ffff8801db300000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000208bc000 CR3:
00000001d9111001 CR4:
00000000001606e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
skb_under_panic net/core/skbuff.c:114 [inline]
skb_push+0xce/0xf0 net/core/skbuff.c:1714
ipgre_header+0x6d/0x4e0 net/ipv4/ip_gre.c:879
dev_hard_header include/linux/netdevice.h:2723 [inline]
pppoe_sendmsg+0x58e/0x8b0 drivers/net/ppp/pppoe.c:890
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:640
sock_write_iter+0x31a/0x5d0 net/socket.c:909
call_write_iter include/linux/fs.h:1775 [inline]
do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653
do_iter_write+0x154/0x540 fs/read_write.c:932
vfs_writev+0x18a/0x340 fs/read_write.c:977
do_writev+0xfc/0x2a0 fs/read_write.c:1012
SYSC_writev fs/read_write.c:1085 [inline]
SyS_writev+0x27/0x30 fs/read_write.c:1082
entry_SYSCALL_64_fastpath+0x29/0xa0
Admittedly PPPoE shouldn't be allowed to run on non Ethernet-like
interfaces, but reserving space for ->needed_headroom is a more
fundamental issue that needs to be addressed first.
Same problem exists for __pppoe_xmit(), which also needs to take
dev->needed_headroom into account in skb_cow_head().
Fixes:
f5184d267c1a ("net: Allow netdevices to specify needed head/tailroom")
Reported-by: syzbot+ed0838d0fa4c4f2b528e20286e6dc63effc7c14d@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Mon, 22 Jan 2018 16:07:19 +0000 (08:07 -0800)]
net: link_watch: mark bonding link events urgent
It takes 1sec for bond link down notification to hit user-space
when all slaves of the bond go down. 1sec is too long for
protocol daemons in user-space relying on bond notification
to recover (eg: multichassis lag implementations in user-space).
Since the link event code already marks team device port link events
as urgent, this patch moves the code to cover all lag ports and master.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>