OSDN Git Service
Sonic Zhang [Wed, 17 Nov 2010 06:19:28 +0000 (06:19 +0000)]
Blackfin: kgdb: disable interrupt when single stepping in ADEOS
When ADEOS and kgdb are both enabled, single step in linux kernel may be
scheduled to Xenomai core after return from interrupt handlers. This
blocks gdb continue operation after a break point is hit. So, disable
interrupt when running gdb single step.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sonic Zhang [Tue, 16 Nov 2010 09:41:07 +0000 (09:41 +0000)]
Blackfin: SMP: kgdb: apply anomaly 257 work around
When run kgdb testing, it looks like coreb hangs in single step or trap
exception without handling anomaly
05000257 properly on bf561 v0.5. But,
the anomaly list says it apply to bf561 v0.4 and bellow. Apply its work
around to 0.5 temporarily until the behavior and the root cause can be
confirmed by the hardware team.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 14 Nov 2010 00:02:53 +0000 (00:02 +0000)]
Blackfin: fix building IPIPE code when XIP is enabled
The low level assembly needs to use the pseudo_long_call helper so that
we use the right call insn when doing kernel XIP.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sonic Zhang [Fri, 12 Nov 2010 05:54:32 +0000 (05:54 +0000)]
Blackfin: SMP: kgdb: flush core internal write buffer before flushinv
KGDB single step in SMP kernel may hang forever in flushinv without a
CSYNC ahead. This is because the core internal write buffers need to
be flushed before invalidating the data cache to make sure the insn
fetch is not out of sync.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sonic Zhang [Fri, 12 Nov 2010 02:45:38 +0000 (02:45 +0000)]
Blackfin: sport_uart resources: remove unused secondary RX/TX pins
The SPORT/UART driver doesn't use the secondary channel pins, so don't
try and request them thus keeping other drivers from using them.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Stefan Weil [Sun, 7 Nov 2010 21:14:53 +0000 (22:14 +0100)]
Blackfin: tll6527m: fix spelling in unused code (struct name)
platfrom -> platform
This changes a struct name. The related code is conditionally
compiled and won't work because the include file linux/gpio-decoder.h
is missing, so removing this code would be an even better solution.
If the missing include file is added, it must fix the spelling, too.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sonic Zhang [Fri, 5 Nov 2010 11:29:46 +0000 (11:29 +0000)]
Blackfin: bf527-ezkit: add adau1373 chip address
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sonic Zhang [Thu, 4 Nov 2010 08:01:37 +0000 (08:01 +0000)]
Blackfin: no-mpu: fix masking of small uncached dma region
When using an uncached DMA region less than 1 MiB, we try to mask off
the whole last 1 MiB for it. Unfortunately, this fails as we forgot
to subtract one from the calculated mask, leading to the region still
be marked as cacheable.
Reported-by: Andrew Rook <andrew.rook@speakerbus.co.uk>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Steven Miao [Wed, 3 Nov 2010 09:25:09 +0000 (09:25 +0000)]
Blackfin: pm: drop irq save/restore in standby and suspend to mem callback
Since linux-2.6.31, the kernel suspend framework will do disable_irq/enable_irq,
so save/restore irq in standby and suspend to mem callback should be dropped.
Otherwise the common code notices things are enabled and complains.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Michael Hennerich [Thu, 28 Oct 2010 11:31:28 +0000 (11:31 +0000)]
MAINTAINERS: update Analog Devices support info
Add more Analog Devices driver entries and refine the differences between
Blackfin-specific code and processor independent drivers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 28 Oct 2010 19:34:09 +0000 (15:34 -0400)]
Blackfin: dpmc.h: pull in new pll.h
Any consumer of dpmc.h expects to use VR_CTL, so also pull in the new
mach/pll.h header for those functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 20:21:51 +0000 (20:21 +0000)]
Blackfin: bf54x: add MMR layout for PINT
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 20:32:24 +0000 (16:32 -0400)]
Blackfin: bf561: SMP: add multicore pll handlers
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 19:29:26 +0000 (15:29 -0400)]
Blackfin: unify pll.h headers
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Yi Li [Thu, 17 Dec 2009 08:20:32 +0000 (08:20 +0000)]
Blackfin: SMP: rewrite IPI handling to avoid memory allocation
Currently, sending an interprocessor interrupt (IPI) requires building up
a message dynamically which means memory allocation. But often times, we
will want to send an IPI in low level contexts where allocation is not
possible which may lead to a panic(). So create a per-cpu static array
for the message queue and use that instead.
Further, while we have two supplemental interrupts, we are currently only
using one of them. So use the second one for the most common IPI message
of all -- smp_send_reschedule(). This avoids ugly contention for locks
which in turn would require an IPI message ...
In general, this improves SMP performance, and in some cases allows the
SMP port to work in places it wouldn't before. Such as the PREEMPT_RT
state where the slab is protected by a per-cpu spin lock. If the slab
kmalloc/kfree were to put the task to sleep, and that task was actually
the IPI handler, then the system falls down yet again.
After running some various stress tests on the system, the static limit
of 5 messages seems to work. On the off chance even this overflows, we
simply panic(), and we can review that scenario to see if the limit needs
to be increased a bit more.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Graf Yang [Mon, 21 Sep 2009 11:51:31 +0000 (11:51 +0000)]
Blackfin: SMP: relocate blackfin_core_id() definition
Since we're breaking apart some inter-header dependencies to avoid more
circular loops, move the blackfin_core_id() definition to the func that
it is based upon.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 14:07:33 +0000 (10:07 -0400)]
Blackfin: SMP: fix build breakage in cache.h
The SMP code needs "asmlinkage" which linkage.h provides.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Graf Yang [Mon, 21 Sep 2009 11:51:31 +0000 (11:51 +0000)]
Blackfin: SMP: add missing arch_{read,write}_lock_flags helpers
Common code expects these to be defined for SMP ports, so add them.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Graf Yang [Mon, 21 Sep 2009 11:51:31 +0000 (11:51 +0000)]
Blackfin: bf561: fix mem_map.h SMP overrides
The BF561 mem_map.h header has the __ASSEMBLY__/CONFIG_SMP checks out
of order which leads to build errors for assembly code that happens to
include this file.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Graf Yang [Mon, 21 Sep 2009 11:51:31 +0000 (11:51 +0000)]
Blackfin: SMP: tweak platform_request_ipi() usage
This function takes an irq_handler_t function, but the prototype in
the header doesn't match the function definition. This is due to the
smp headers needing to avoid circular dependencies. So change the
function to take a simple pointer.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 21 Sep 2009 11:51:31 +0000 (11:51 +0000)]
Blackfin: SMP: fix asm/bitops.h errors
The common asm-generic non-atomic bitops.h defines test_bit() for us, but
we need to use our own version. So redirect the definition of this func
to avoid having to inline the rest of the asm-generic file.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Graf Yang [Mon, 21 Sep 2009 11:51:31 +0000 (11:51 +0000)]
Blackfin: SMP: fix cpumask misbehavior
The cpu maps are defines provided by common linux/cpumask.h, not local
variables. So stop exporting them locally and include the right header
for their definition.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Graf Yang [Fri, 12 Mar 2010 04:24:21 +0000 (04:24 +0000)]
Blackfin: SMP: rename the arch_xxx lock funcs to __raw_xxx
The external functions are named __raw_xxx, not arch_xxx, so rename the
prototypes to match reality. This fixes some simple build errors in the
bfin_ksyms.c code which exports these helpers to modules.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sonic Zhang [Wed, 9 Sep 2009 10:46:19 +0000 (10:46 +0000)]
serial: bfin_5xx: move resources into board files
Rather than maintain Kconfig entries where people have to enter raw
numbers and hardcode lists of addresses/pins in the driver itself,
push it all to platform resources. This lets us simplify the driver,
the Kconfig, and gives board porters greater flexibility.
In the process, we need to also start supporting the early platform
interface. Not a big deal, but it causes the patch to be bigger than
a simple resource relocation.
All the Blackfin boards already have their resources updated and in
place for this change.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 14:06:32 +0000 (10:06 -0400)]
Blackfin: bf561: update a few more SIC_SYSCR locations
Looks like I missed a few new spots when renaming the SICA macros.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 04:08:46 +0000 (00:08 -0400)]
Blackfin: drop asm/irq.h include from mach headers
These were only included because of the irq handling of the PLL funcs,
and those PLL funcs have been moved out into their own header now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 03:56:12 +0000 (23:56 -0400)]
Blackfin: bf51x/bf52x: drop redundant "base" def/cdef header
The
defBF512.h header exists only to include defBF51x_base.h, and it is
the only place where defBF51x_base.h is included. So move the contents
of the defBF51x_base.h header into the
defBF512.h header.
Same situation for the other def/cdef pairs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 03:46:22 +0000 (23:46 -0400)]
Blackfin: clean up mach header includes
The main asm/blackfin.h header will pull in mach/blackfin.h to get
all the fun Blackfin defines. So having any of the sub-mach headers
trying to include asm/blackfin.h makes no sense -- punt it.
The mach/blackfin.h header takes care of including the part-specific
def headers which in turn will include any other needed def file.
Similarly, it takes care of pulling in the part-specific cdef header.
So move this logic out of the blackfin.h when necessary.
Further, make sure the cdef headers do not waste time including the
def headers again.
Since all parts need the common def/cdef headers, move this logic
out of the part-specific headers and into the mach/blackfin.h file.
Finally, we need to split the BF539 def header since the BF538 does
not have MXVR and we don't want to expose those MMRs.
So now all parts should have the same behavior:
mach/blackfin.h
asm/def_LPBlackfin.h
part-specific def.h
if ! asm
asm/cdef_LPBlackfin.h
part-specific cdef.h
And the sub def/cdef headers only tail into what they need.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 02:55:28 +0000 (22:55 -0400)]
Blackfin: bf533: merge fio_flag back into normal mach headers
We don't want the BF533 to be different in terms of its MMR headers, so
merge the FIO_FLAG helpers back into the normal place. To avoid circular
dependencies with headers, turn the inline C funcs into CPP defines. Not
like there will be any code size differences.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 01:40:31 +0000 (21:40 -0400)]
Blackfin: bf561-ezkit: add SMP defconfig
Since the SMP code paths tend to compile fail a lot, start a SMP defconfig
so our nightly build tools will automatically test it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 01:30:29 +0000 (21:30 -0400)]
Blackfin: bf533: convert boards to gpio framework
We don't want people banging on MMRs directly. As for the ip0x board,
it shouldn't need to muck with the CS pin directly as the Blackfin SPI
bus master driver takes care of driving this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 26 Oct 2010 01:11:10 +0000 (21:11 -0400)]
Blackfin: push gpio (port) defines into common headers
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 26 Oct 2010 01:10:43 +0000 (21:10 -0400)]
Blackfin: bf54x: drop unused legacy MMR names
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 25 Oct 2010 18:11:09 +0000 (18:11 +0000)]
Blackfin: dma: constify MMR pointer array
The array of pointers is never written, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 25 Oct 2010 08:04:44 +0000 (08:04 +0000)]
Blackfin: standardize DMAC traffic control MMRs & MDMA MMRs
Use the same naming convention for DMA traffic MMRs (most were legacy
anyways) so we can avoid useless ifdef trees.
Same goes for MDMA names -- this actually allows us to undo a bunch of
ifdef redirects that existed for this purpose alone.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 25 Oct 2010 08:02:30 +0000 (08:02 +0000)]
Blackfin: bfin_dma.h: start a header for DMA MMR layout
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 16 Feb 2010 09:03:18 +0000 (04:03 -0500)]
Blackfin: switch to asm-generic/io.h
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 27 Oct 2010 01:52:59 +0000 (21:52 -0400)]
asm-generic/io.h: add reads[bwl]/writes[bwl] helpers
A bunch of arches define reads[bwl]/writes[bwl] helpers for accessing
memory mapped registers. Since the Blackfin ones aren't specific to
Blackfin code, move them to the common asm-generic/io.h for people.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 10 Jan 2011 07:45:57 +0000 (02:45 -0500)]
net/irda: bfin_sir: back out transitional defines
Now that the common header is sane, we can drop the transitional cruft.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 28 Sep 2009 03:16:01 +0000 (03:16 +0000)]
Blackfin: bfin_serial.h: unify heavily duplicated serial code
Each Blackfin port has been duplicating UART structures and defines when
there really is no need for it. So start a new bfin_serial.h header to
unify all these pieces and give ourselves a fresh start.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 28 Oct 2010 19:43:50 +0000 (15:43 -0400)]
net/irda: bfin_sir: pull in serial headers for defines
We're in the process of cleaning up the global Blackfin namespace, so the
bfin_sir driver needs to pull in the serial header explicitly now.
This does add a little transitional cruft to keep things compiling, but a
follow up patch in this series will cull that.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Bob Liu [Fri, 17 Sep 2010 11:09:57 +0000 (11:09 +0000)]
Blackfin: musb-boards: push clkin value to platform resources
In order to not touch the driver file for different xtal usage,
push the clkin value to board file and calculate the register
value instead of hardcoding it.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Graf Yang [Thu, 28 Jan 2010 10:46:55 +0000 (10:46 +0000)]
Blackfin: SMP: fix hotplug building after irq header shuffle
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Linus Torvalds [Sat, 8 Jan 2011 01:16:27 +0000 (17:16 -0800)]
Merge branch 'for-next' of git://git./linux/kernel/git/hch/hfsplus
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/hfsplus:
hfsplus: %L-to-%ll, macro correction, and remove unneeded braces
hfsplus: spaces/indentation clean-up
hfsplus: C99 comments clean-up
hfsplus: over 80 character lines clean-up
hfsplus: fix an artifact in ioctl flag checking
hfsplus: flush disk caches in sync and fsync
hfsplus: optimize fsync
hfsplus: split up inode flags
hfsplus: write up fsync for directories
hfsplus: simplify fsync
hfsplus: avoid useless work in hfsplus_sync_fs
hfsplus: make sure sync writes out all metadata
hfsplus: use raw bio access for partition tables
hfsplus: use raw bio access for the volume headers
hfsplus: always use hfsplus_sync_fs to write the volume header
hfsplus: silence a few debug printks
hfsplus: fix option parsing during remount
Fix up conflicts due to VFS changes in fs/hfsplus/{hfsplus_fs.h,unicode.c}
Linus Torvalds [Sat, 8 Jan 2011 01:08:46 +0000 (17:08 -0800)]
Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
spi/omap: Fix DMA API usage in OMAP MCSPI driver
spi/imx: correct the test on platform_get_irq() return value
spi/topcliff: Typo fix threhold to threshold
spi/dw_spi Typo change diable to disable.
spi/fsl_espi: change the read behaviour of the SPIRF
spi/mpc52xx-psc-spi: move probe/remove to proper sections
spi/dw_spi: add DMA support
spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
spi/dw_spi: Fix too short timeout in spi polling loop
spi/pl022: convert running variable
spi/pl022: convert busy flag to a bool
spi/pl022: pass the returned sglen to the DMA engine
spi/pl022: map the buffers on the DMA engine
spi/topcliff_pch: Fix data transfer issue
spi/imx: remove autodetection
spi/pxa2xx: pass of_node to spi device and set a parent device
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add CE4100 support
...
Linus Torvalds [Sat, 8 Jan 2011 01:02:58 +0000 (17:02 -0800)]
Merge branch 'for-2.6.38' of git://git./linux/kernel/git/tj/percpu
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (30 commits)
gameport: use this_cpu_read instead of lookup
x86: udelay: Use this_cpu_read to avoid address calculation
x86: Use this_cpu_inc_return for nmi counter
x86: Replace uses of current_cpu_data with this_cpu ops
x86: Use this_cpu_ops to optimize code
vmstat: User per cpu atomics to avoid interrupt disable / enable
irq_work: Use per cpu atomics instead of regular atomics
cpuops: Use cmpxchg for xchg to avoid lock semantics
x86: this_cpu_cmpxchg and this_cpu_xchg operations
percpu: Generic this_cpu_cmpxchg() and this_cpu_xchg support
percpu,x86: relocate this_cpu_add_return() and friends
connector: Use this_cpu operations
xen: Use this_cpu_inc_return
taskstats: Use this_cpu_ops
random: Use this_cpu_inc_return
fs: Use this_cpu_inc_return in buffer.c
highmem: Use this_cpu_xx_return() operations
vmstat: Use this_cpu_inc_return for vm statistics
x86: Support for this_cpu_add, sub, dec, inc_return
percpu: Generic support for this_cpu_add, sub, dec, inc_return
...
Fixed up conflicts: in arch/x86/kernel/{apic/nmi.c, apic/x2apic_uv_x.c, process.c}
as per Tejun.
Linus Torvalds [Sat, 8 Jan 2011 00:58:04 +0000 (16:58 -0800)]
Merge branch 'for-2.6.38' of git://git./linux/kernel/git/tj/wq
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Linus Torvalds [Fri, 7 Jan 2011 22:55:48 +0000 (14:55 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Constify function scope static struct sched_param usage
sched: Fix strncmp operation
sched: Move sched_autogroup_exit() to free_signal_struct()
sched: Fix struct autogroup memory leak
sched: Mark autogroup_init() __init
sched: Consolidate the name of root_task_group and init_task_group
Linus Torvalds [Fri, 7 Jan 2011 22:55:31 +0000 (14:55 -0800)]
Merge branch 'x86-apic-cleanups-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-apic-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: apic: Cleanup and simplify setup_local_APIC()
x86: Further simplify mp_irq info handling
x86: Unify 3 similar ways of saving mp_irqs info
x86, ioapic: Avoid writing io_apic id if already correct
x86, x2apic: Don't map lapic addr for preenabled x2apic systems
x86, sfi: Use register_lapic_address()
x86, apic: Use register_lapic_address() in init_apic_mapping()
x86, apic: Remove early_init_lapic_mapping()
x86, apic: Unify identical register_lapic_address() functions
Linus Torvalds [Fri, 7 Jan 2011 22:54:03 +0000 (14:54 -0800)]
Merge branch 'mce-for-linus' of git://git./linux/kernel/git/bp/bp
* 'mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, MCE: Fix NB error formatting
EDAC, MCE: Use BIT_64() to eliminate warnings on 32-bit
EDAC, MCE: Enable MCE decoding on F15h
EDAC, MCE: Allow F15h bank 6 MCE injection
EDAC, MCE: Shorten error report formatting
EDAC, MCE: Overhaul error fields extraction macros
EDAC, MCE: Add F15h FP MCE decoder
EDAC, MCE: Add F15 EX MCE decoder
EDAC, MCE: Add an F15h NB MCE decoder
EDAC, MCE: No F15h LS MCE decoder
EDAC, MCE: Add F15h CU MCE decoder
EDAC, MCE: Add F15h IC MCE decoder
EDAC, MCE: Add F15h DC MCE decoder
EDAC, MCE: Select extended error code mask
Linus Torvalds [Fri, 7 Jan 2011 22:53:42 +0000 (14:53 -0800)]
Merge branch 'edac-for-linus' of git://git./linux/kernel/git/bp/bp
* 'edac-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Disable DRAM ECC injection on K8
EDAC: Fixup scrubrate manipulation
amd64_edac: Remove two-stage initialization
amd64_edac: Check ECC capabilities initially
amd64_edac: Carve out ECC-related hw settings
amd64_edac: Remove PCI ECS enabling functions
amd64_edac: Remove explicit Kconfig PCI dependency
amd64_edac: Allocate driver instances dynamically
amd64_edac: Rework printk macros
amd64_edac: Rename CPU PCI devices
amd64_edac: Concentrate per-family init even more
amd64_edac: Cleanup the CPU PCI device reservation
amd64_edac: Simplify CPU family detection
amd64_edac: Add per-family init function
amd64_edac: Use cached extended CPU model
amd64_edac: Remove F11h support
Linus Torvalds [Fri, 7 Jan 2011 22:50:50 +0000 (14:50 -0800)]
Merge branch 'for-linus' of git://git390.marist.edu/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (65 commits)
[S390] prevent unneccesary loops_per_jiffy recalculation
[S390] cpuinfo: use get_online_cpus() instead of preempt_disable()
[S390] smp: remove cpu hotplug messages
[S390] mutex: enable spinning mutex on s390
[S390] mutex: Introduce arch_mutex_cpu_relax()
[S390] cio: fix ccwgroup unregistration race condition
[S390] perf: add DWARF register lookup for s390
[S390] cleanup ftrace backend functions
[S390] ptrace cleanup
[S390] smp/idle: call init_idle() before starting a new cpu
[S390] smp: delay idle task creation
[S390] dasd: Correct retry counter for terminated I/O.
[S390] dasd: Add support for raw ECKD access.
[S390] dasd: Prevent deadlock during suspend/resume.
[S390] dasd: Improve handling of stolen DASD reservation
[S390] dasd: do path verification for paths added at runtime
[S390] dasd: add High Performance FICON multitrack support
[S390] cio: reduce memory consumption of itcw structures
[S390] nmi: enable machine checks early
[S390] qeth: buffer count imbalance
...
Linus Torvalds [Fri, 7 Jan 2011 22:50:14 +0000 (14:50 -0800)]
Merge branch 'rmobile-latest' of git://git./linux/kernel/git/lethal/sh-2.6
* 'rmobile-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (67 commits)
ARM: mach-shmobile: update for SMP changes.
ARM: mach-shmobile: update for GIC changes.
ARM: mach-shmobile: Fix up clkdev fallout for SH73A0.
dma: shdma: don't register the global die notifier multiple times
ARM: mach-shmobile: Rely on run-time IRQ handlers
ARM: mach-shmobile: Run-time IRQ handler for GIC
ARM: mach-shmobile: Run-time IRQ handler for INTCA
ARM: mach-shmobile: Enable CONFIG_MULTI_IRQ_HANDLER
ARM: mach-shmobile: Use shared GIC entry macros
ARM: mach-shmobile: mackerel: Add zboot support
ARM: mach-shmobile: mackerel: Add HDMI sound support
ARM: mach-shmobile: mackerel: add HDMI video support
ARM: mach-shmobile: ap4evb: fixup clk_put timing of fsib_clk
ARM: mach-shmobile: sh73a0: fix div4 table
ARM: mach-shmobile: ap4/mackerel: modify wrong comment out of USB
ARM: mach-shmobile: Mackerel VGA camera support
mmc: sh_mmcif: make DMA support by the driver unconditional
ARM: mach-shmobile: Add eMMC support through MMCIF on AG5EVM
ARM: mach-shmobile: Use pullups for AG5EVM KEYSC pins
ARM: mach-shmobile: sh73a0 GPIO pullup improvement
...
Linus Torvalds [Fri, 7 Jan 2011 22:45:47 +0000 (14:45 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (58 commits)
Input: wacom_w8001 - support pen or touch only devices
Input: wacom_w8001 - use __set_bit to set keybits
Input: bu21013_ts - fix misuse of logical operation in place of bitop
Input: i8042 - add Acer Aspire 5100 to the Dritek list
Input: wacom - add support for digitizer in Lenovo W700
Input: psmouse - disable the synaptics extension on OLPC machines
Input: psmouse - fix up Synaptics comment
Input: synaptics - ignore bogus mt packet
Input: synaptics - add multi-finger and semi-mt support
Input: synaptics - report clickpad property
input: mt: Document interface updates
Input: fix double equality sign in uevent
Input: introduce device properties
hid: egalax: Add support for Wetab (726b)
Input: include MT library as source for kerneldoc
MAINTAINERS: Update input-mt entry
hid: egalax: Add support for Samsung NB30 netbook
hid: egalax: Document the new devices in Kconfig
hid: egalax: Add support for Wetab
hid: egalax: Convert to MT slots
...
Fixed up trivial conflict in drivers/input/keyboard/Kconfig
Linus Torvalds [Fri, 7 Jan 2011 22:39:20 +0000 (14:39 -0800)]
Merge branch 'tty-next' of git://git./linux/kernel/git/gregkh/tty-2.6
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
serial: apbuart: Fixup apbuart_console_init()
TTY: Add tty ioctl to figure device node of the system console.
tty: add 'active' sysfs attribute to tty0 and console device
drivers: serial: apbuart: Handle OF failures gracefully
Serial: Avoid unbalanced IRQ wake disable during resume
tty: fix typos/errors in tty_driver.h comments
pch_uart : fix warnings for 64bit compile
8250: fix uninitialized FIFOs
ip2: fix compiler warning on ip2main_pci_tbl
specialix: fix compiler warning on specialix_pci_tbl
rocket: fix compiler warning on rocket_pci_ids
8250: add a UPIO_DWAPB32 for 32 bit accesses
8250: use container_of() instead of casting
serial: omap-serial: Add support for kernel debugger
serial: fix pch_uart kconfig & build
drivers: char: hvc: add arm JTAG DCC console support
RS485 documentation: add 16C950 UART description
serial: ifx6x60: fix memory leak
serial: ifx6x60: free IRQ on error
Serial: EG20T: add PCH_UART driver
...
Fixed up conflicts in drivers/serial/apbuart.c with evil merge that
makes the code look fairly sane (unlike either side).
Linus Torvalds [Fri, 7 Jan 2011 21:16:28 +0000 (13:16 -0800)]
Merge branch 'usb-next' of git://git./linux/kernel/git/gregkh/usb-2.6
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
Linus Torvalds [Fri, 7 Jan 2011 20:47:02 +0000 (12:47 -0800)]
Merge git://git./linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (147 commits)
[SCSI] arcmsr: fix write to device check
[SCSI] lpfc: lower stack use in lpfc_fc_frame_check
[SCSI] eliminate an unnecessary local variable from scsi_remove_target()
[SCSI] libiscsi: use bh locking instead of irq with session lock
[SCSI] libiscsi: do not take host lock in queuecommand
[SCSI] be2iscsi: fix null ptr when accessing task hdr
[SCSI] be2iscsi: fix gfp use in alloc_pdu
[SCSI] libiscsi: add more informative failure message during iscsi scsi eh
[SCSI] gdth: Add missing call to gdth_ioctl_free
[SCSI] bfa: remove unused defintions and misc cleanups
[SCSI] bfa: remove inactive functions
[SCSI] bfa: replace bfa_assert with WARN_ON
[SCSI] qla2xxx: Use sg_next to fetch next sg element while walking sg list.
[SCSI] qla2xxx: Fix to avoid recursive lock failure during BSG timeout.
[SCSI] qla2xxx: Remove code to not reset ISP82xx on failure.
[SCSI] qla2xxx: Display mailbox register 4 during 8012 AEN for ISP82XX parts.
[SCSI] qla2xxx: Don't perform a BIG_HAMMER if Get-ID (0x20) mailbox command fails on CNAs.
[SCSI] qla2xxx: Remove redundant module parameter permission bits
[SCSI] qla2xxx: Add sysfs node for displaying board temperature.
[SCSI] qla2xxx: Code cleanup to remove unwanted comments and code.
...
Dan Carpenter [Fri, 7 Jan 2011 19:47:37 +0000 (20:47 +0100)]
input/tc3589x: fix compile error
There was a semi-colon missing and it broke the compile.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King - ARM Linux [Fri, 7 Jan 2011 15:49:20 +0000 (15:49 +0000)]
spi/omap: Fix DMA API usage in OMAP MCSPI driver
Running the latest kernel on the 4430SDP board with DMA API debugging
enabled results in this:
WARNING: at lib/dma-debug.c:803 check_unmap+0x19c/0x6f0()
NULL NULL: DMA-API: device driver tries to free DMA memory it has not allocated
[device address=0x000000008129901a] [size=260 bytes]
Modules linked in:
Backtrace:
[<
c003cbe0>] (dump_backtrace+0x0/0x10c) from [<
c0278da8>] (dump_stack+0x18/0x1c)
r7:
c1839dc0 r6:
c0198578 r5:
c0304b17 r4:
00000323
[<
c0278d90>] (dump_stack+0x0/0x1c) from [<
c005b158>] (warn_slowpath_common+0x58/0x70)
[<
c005b100>] (warn_slowpath_common+0x0/0x70) from [<
c005b214>] (warn_slowpath_fmt+0x38/0x40)
r8:
c1839e40 r7:
00000000 r6:
00000104 r5:
00000000 r4:
8129901a
[<
c005b1dc>] (warn_slowpath_fmt+0x0/0x40) from [<
c0198578>] (check_unmap+0x19c/0x6f0)
r3:
c03110de r2:
c0304e6b
[<
c01983dc>] (check_unmap+0x0/0x6f0) from [<
c0198cd8>] (debug_dma_unmap_page+0x74/0x80)
[<
c0198c64>] (debug_dma_unmap_page+0x0/0x80) from [<
c01d5ad8>] (omap2_mcspi_work+0x514/0xbf0)
[<
c01d55c4>] (omap2_mcspi_work+0x0/0xbf0) from [<
c006dfb0>] (process_one_work+0x294/0x400)
[<
c006dd1c>] (process_one_work+0x0/0x400) from [<
c006e50c>] (worker_thread+0x220/0x3f8)
[<
c006e2ec>] (worker_thread+0x0/0x3f8) from [<
c00738d0>] (kthread+0x88/0x90)
[<
c0073848>] (kthread+0x0/0x90) from [<
c005e924>] (do_exit+0x0/0x5fc)
r7:
00000013 r6:
c005e924 r5:
c0073848 r4:
c1829ee0
---[ end trace
1b75b31a2719ed20 ]---
I've no idea why this driver uses NULL for dma_unmap_single instead of
the &spi->dev that is laying around just waiting to be used in that
function - but it's an easy fix.
Also replace this comment with a FIXME comment:
/* Do DMA mapping "early" for better error reporting and
* dcache use. Note that if dma_unmap_single() ever starts
* to do real work on ARM, we'd need to clean up mappings
* for previous transfers on *ALL* exits of this loop...
*/
as the comment is not true - we do work in dma_unmap() functions,
particularly on ARMv6 and above. I've corrected the existing unmap
functions but if any others are required they must be added ASAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Richard Genoud [Fri, 7 Jan 2011 14:26:01 +0000 (15:26 +0100)]
spi/imx: correct the test on platform_get_irq() return value
The test "if (spi_imx->irq <= 0)" is not testing the IRQ value, but
the return value of platform_get_irq(). As platform_get_irq() can
return an error (-ENXIO) or the IRQ value it found, the test should be
"if (spi_imx->irq < 0)"
[grant.likely: Note: In general, Linux irq number 0 should also mean
no irq, but arm still allows devices to be assigned 0, and the imx
platform uses 0 for one of the spi devices, so this patch is needed
for the device to work]
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Linus Torvalds [Fri, 7 Jan 2011 16:56:33 +0000 (08:56 -0800)]
Merge branch 'vfs-scale-working' of git://git./linux/kernel/git/npiggin/linux-npiggin
* 'vfs-scale-working' of git://git.kernel.org/pub/scm/linux/kernel/git/npiggin/linux-npiggin: (57 commits)
fs: scale mntget/mntput
fs: rename vfsmount counter helpers
fs: implement faster dentry memcmp
fs: prefetch inode data in dcache lookup
fs: improve scalability of pseudo filesystems
fs: dcache per-inode inode alias locking
fs: dcache per-bucket dcache hash locking
bit_spinlock: add required includes
kernel: add bl_list
xfs: provide simple rcu-walk ACL implementation
btrfs: provide simple rcu-walk ACL implementation
ext2,3,4: provide simple rcu-walk ACL implementation
fs: provide simple rcu-walk generic_check_acl implementation
fs: provide rcu-walk aware permission i_ops
fs: rcu-walk aware d_revalidate method
fs: cache optimise dentry and inode for rcu-walk
fs: dcache reduce branches in lookup path
fs: dcache remove d_mounted
fs: fs_struct use seqlock
fs: rcu-walk for path lookup
...
Peter Zijlstra [Fri, 7 Jan 2011 12:41:40 +0000 (13:41 +0100)]
sched: Constify function scope static struct sched_param usage
Function-scope statics are discouraged because they are
easily overlooked and can cause subtle bugs/races due to
their global (non-SMP safe) nature.
Linus noticed that we did this for sched_param - at minimum
make the const.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: Message-ID: <AANLkTinotRxScOHEb0HgFgSpGPkq_6jKTv5CfvnQM=ee@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Hillf Danton [Thu, 6 Jan 2011 12:58:12 +0000 (20:58 +0800)]
sched: Fix strncmp operation
One of the operands, buf, is incorrect, since it is stripped and the
correct address for subsequent string comparing could change if
leading white spaces, if any, are removed from buf.
It is fixed by replacing buf with cmp.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <AANLkTinOPuYsVovrZpbuCCmG5deEyc8WgA_A1RJx_YK7@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mike Galbraith [Wed, 5 Jan 2011 10:16:04 +0000 (11:16 +0100)]
sched: Move sched_autogroup_exit() to free_signal_struct()
Per Oleg's suggestion, undo fork failure free/put_signal_struct change,
and move sched_autogroup_exit() to free_signal_struct() instead.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1294222564.8369.6.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mike Galbraith [Wed, 5 Jan 2011 10:11:25 +0000 (11:11 +0100)]
sched: Fix struct autogroup memory leak
Seems I lost a change somewhere, leaking memory.
sched: fix struct autogroup memory leak
Add missing change to actually use autogroup_free().
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1294222285.8369.2.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yong Zhang [Fri, 7 Jan 2011 04:43:45 +0000 (12:43 +0800)]
sched: Mark autogroup_init() __init
autogroup_init() is only called at boot time.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1294375425-31065-1-git-send-email-yong.zhang0@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yong Zhang [Fri, 7 Jan 2011 07:17:36 +0000 (15:17 +0800)]
sched: Consolidate the name of root_task_group and init_task_group
root_task_group is the leftover of USER_SCHED, now it's always
same to init_task_group.
But as Mike suggested, root_task_group is maybe the suitable name
to keep for a tree.
So in this patch:
init_task_group --> root_task_group
init_task_group_load --> root_task_group_load
INIT_TASK_GROUP_LOAD --> ROOT_TASK_GROUP_LOAD
Suggested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
20110107071736.GA32635@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Fri, 7 Jan 2011 13:14:15 +0000 (14:14 +0100)]
Merge branch 'linus' into x86/apic-cleanups
Conflicts:
arch/x86/include/asm/io_apic.h
Merge reason: Resolve the conflict, update to a more recent -rc base
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Borislav Petkov [Thu, 25 Nov 2010 14:40:27 +0000 (15:40 +0100)]
EDAC, MCE: Fix NB error formatting
Minor formatting fixup since the information which core was associated
with the MCE is not always valid.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Randy Dunlap [Sat, 13 Nov 2010 16:44:26 +0000 (11:44 -0500)]
EDAC, MCE: Use BIT_64() to eliminate warnings on 32-bit
Building for X86_32 produces shift count warnings, so use BIT_64() to
eliminate the warnings.
drivers/edac/mce_amd.c:778: warning: left shift count >= width of type
drivers/edac/mce_amd.c:778: warning: left shift count >= width of type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: bluesmoke-devel@lists.sourceforge.net
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 22 Sep 2010 15:44:51 +0000 (17:44 +0200)]
EDAC, MCE: Enable MCE decoding on F15h
Now that everything is inplace, enable MCE decoding on F15h. Make
initcall routine a bit more readable.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Tue, 9 Nov 2010 18:41:49 +0000 (19:41 +0100)]
EDAC, MCE: Allow F15h bank 6 MCE injection
F15h adds a sixth MCE bank: adjust bank number check in the injection
code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 22 Sep 2010 15:42:27 +0000 (17:42 +0200)]
EDAC, MCE: Shorten error report formatting
Shorten up MCi_STATUS flags and add BD's new deferred and poison types.
Also, simplify formatting.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 22 Sep 2010 14:08:37 +0000 (16:08 +0200)]
EDAC, MCE: Overhaul error fields extraction macros
Make macro names shorter thus making code shorter and more clear.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 22 Sep 2010 13:37:58 +0000 (15:37 +0200)]
EDAC, MCE: Add F15h FP MCE decoder
Add decoder for FP MCEs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 22 Sep 2010 13:28:59 +0000 (15:28 +0200)]
EDAC, MCE: Add F15 EX MCE decoder
Integrate the single FIROB signature into an expanded table along with
the new BD MCE types.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 22 Sep 2010 13:06:24 +0000 (15:06 +0200)]
EDAC, MCE: Add an F15h NB MCE decoder
by (almost) reusing the F10h one since the signatures are the same.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 22 Sep 2010 09:53:32 +0000 (11:53 +0200)]
EDAC, MCE: No F15h LS MCE decoder
F15h BD doesn't generate LS MCEs so warn about it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Tue, 21 Sep 2010 18:45:10 +0000 (20:45 +0200)]
EDAC, MCE: Add F15h CU MCE decoder
MCE bank 2 is redefined from a BU to a CU (Combined Unit) bank on F15h.
Add a decoder function for CU MCEs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Mon, 8 Nov 2010 14:03:35 +0000 (15:03 +0100)]
EDAC, MCE: Add F15h IC MCE decoder
Add support for decoding F15h IC MCEs.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 17 Sep 2010 17:22:34 +0000 (19:22 +0200)]
EDAC, MCE: Add F15h DC MCE decoder
Add a decoder for F15h DC MCEs to support the new types of DC MCEs
introduced by the BD microarchitecture.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 17 Sep 2010 17:11:47 +0000 (19:11 +0200)]
EDAC, MCE: Select extended error code mask
F15h enlarges the extended error code of an MCE to a 5-bit field
(MCi_STATUS[20:16]). Add a mask variable which default 0xf is overridden
on F15h.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 26 Nov 2010 18:24:44 +0000 (19:24 +0100)]
amd64_edac: Disable DRAM ECC injection on K8
K8 does not allow for an atomic RMW to a cacheline as F10h does so
disable the error injection interface for it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 24 Nov 2010 18:52:09 +0000 (19:52 +0100)]
EDAC: Fixup scrubrate manipulation
Make the ->{get|set}_sdram_scrub_rate return the actual scrub rate
bandwidth it succeeded setting and remove superfluous arg pointer used
for that. A negative value returned still means that an error occurred
while setting the scrubrate. Document this for future reference.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 15 Oct 2010 17:25:38 +0000 (19:25 +0200)]
amd64_edac: Remove two-stage initialization
Now that all prerequisites are in place, drop the two-stage driver
instances initialization in favor of the following simple init sequence:
1. Probe PCI device: we only test ECC capabilities here and if none exit
early.
2. If the hw supports ECC and it is/can be enabled, we init the per-node
instance.
Remove "amd64_" prefix from static functions touched, while at it.
There actually should be no visible functional change resulting from
this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 15 Oct 2010 15:44:04 +0000 (17:44 +0200)]
amd64_edac: Check ECC capabilities initially
Rework the code to check the hardware ECC capabilities at PCI probing
time. We do all further initialization only if we actually can/have ECC
enabled.
While at it:
0. Fix function naming.
1. Simplify/clarify debug output.
2. Remove amd64_ prefix from the static functions
3. Reorganize code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Thu, 14 Oct 2010 14:01:30 +0000 (16:01 +0200)]
amd64_edac: Carve out ECC-related hw settings
This is in preparation for the init path reorganization where we want
only to
1) test whether a particular node supports ECC
2) can it be enabled
and only then do the necessary allocation/initialization. For that,
we need to decouple the ECC settings of the node from the instance's
descriptor.
The should be no functional change introduced by this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Thu, 14 Oct 2010 12:37:13 +0000 (14:37 +0200)]
amd64_edac: Remove PCI ECS enabling functions
PCI ECS is being enabled by default since 2.6.26 on AMD so this code is
just superfluous now, remove it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 13 Oct 2010 20:12:15 +0000 (22:12 +0200)]
amd64_edac: Remove explicit Kconfig PCI dependency
AMD_NB pulls in the dependency on PCI. Clarify/fix help text while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Wed, 13 Oct 2010 14:11:59 +0000 (16:11 +0200)]
amd64_edac: Allocate driver instances dynamically
Remove static allocation in favor of dynamically allocating space for as
many driver instances as northbridges present on the system.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Thu, 7 Oct 2010 16:29:15 +0000 (18:29 +0200)]
amd64_edac: Rework printk macros
Add a macro per printk level, shorten up error messages. Add relevant
information to KERN_INFO level. No functional change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 1 Oct 2010 18:11:07 +0000 (20:11 +0200)]
amd64_edac: Rename CPU PCI devices
Rename variables representing PCI devices to their BKDG names for faster
search and shorter, clearer code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 1 Oct 2010 17:35:38 +0000 (19:35 +0200)]
amd64_edac: Concentrate per-family init even more
Move the remaining per-family init code into the proper place and
simplify the rest of the initialization. Reorganize error handling in
amd64_init_one_instance().
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 1 Oct 2010 17:27:58 +0000 (19:27 +0200)]
amd64_edac: Cleanup the CPU PCI device reservation
Shorten code and clarify comments, return proper -E* values on error.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 1 Oct 2010 17:20:05 +0000 (19:20 +0200)]
amd64_edac: Simplify CPU family detection
Concentrate CPU family detection in the per-family init function.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 1 Oct 2010 16:38:19 +0000 (18:38 +0200)]
amd64_edac: Add per-family init function
Run a per-family init function which does all the settings based on
the family this driver instance is running on. Move the scrubrate
calculation in it and simplify code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 1 Oct 2010 17:44:53 +0000 (19:44 +0200)]
amd64_edac: Use cached extended CPU model
... instead of computing it needlessly again.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Borislav Petkov [Fri, 1 Oct 2010 16:19:06 +0000 (18:19 +0200)]
amd64_edac: Remove F11h support
F11h doesn't support DRAM ECC so whack it away.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Nick Piggin [Fri, 7 Jan 2011 06:50:11 +0000 (17:50 +1100)]
fs: scale mntget/mntput
The problem that this patch aims to fix is vfsmount refcounting scalability.
We need to take a reference on the vfsmount for every successful path lookup,
which often go to the same mount point.
The fundamental difficulty is that a "simple" reference count can never be made
scalable, because any time a reference is dropped, we must check whether that
was the last reference. To do that requires communication with all other CPUs
that may have taken a reference count.
We can make refcounts more scalable in a couple of ways, involving keeping
distributed counters, and checking for the global-zero condition less
frequently.
- check the global sum once every interval (this will delay zero detection
for some interval, so it's probably a showstopper for vfsmounts).
- keep a local count and only taking the global sum when local reaches 0 (this
is difficult for vfsmounts, because we can't hold preempt off for the life of
a reference, so a counter would need to be per-thread or tied strongly to a
particular CPU which requires more locking).
- keep a local difference of increments and decrements, which allows us to sum
the total difference and hence find the refcount when summing all CPUs. Then,
keep a single integer "long" refcount for slow and long lasting references,
and only take the global sum of local counters when the long refcount is 0.
This last scheme is what I implemented here. Attached mounts and process root
and working directory references are "long" references, and everything else is
a short reference.
This allows scalable vfsmount references during path walking over mounted
subtrees and unattached (lazy umounted) mounts with processes still running
in them.
This results in one fewer atomic op in the fastpath: mntget is now just a
per-CPU inc, rather than an atomic inc; and mntput just requires a spinlock
and non-atomic decrement in the common case. However code is otherwise bigger
and heavier, so single threaded performance is basically a wash.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Nick Piggin [Fri, 7 Jan 2011 06:50:10 +0000 (17:50 +1100)]
fs: rename vfsmount counter helpers
Suggested by Andreas, mnt_ prefix is clearer namespace, follows kernel
conventions better, and is easier for tab complete. I introduced these
names so I'll admit they were not good choices.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>