OSDN Git Service
Nick Piggin [Tue, 20 Feb 2007 21:58:08 +0000 (13:58 -0800)]
[PATCH] fs: fix libfs data leak
simple_prepare_write leaks uninitialised kernel data. This happens because
the it leaves an uninitialised "hole" over the part of the page that the
write is expected to go to. This is fine, but it then marks the page
uptodate, which means a concurrent read can come in and copy the
uninitialised memory into userspace before it written to.
Fix it by simply marking it uptodate in simple_commit_write instead, after
the hole has been filled in. This could theoretically break an fs that
uses simple_prepare_write and not simple_commit_write, and that relies on
the incorrect simple_prepare_write behaviour. Luckily, none of those
exists in the tree.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Jones [Tue, 20 Feb 2007 21:58:07 +0000 (13:58 -0800)]
[PATCH] loosen dependancy on rtc cmos
This option is useful for all of the X86 subarchs afaik (and especially
X86_GENERICARCH).
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simon Horman [Tue, 20 Feb 2007 21:58:07 +0000 (13:58 -0800)]
[PATCH] PPC64 Kdump documentation update
Patch from Mohan Kumar M to add the ppc64 portions of the kdump
documentation.
http://thread.gmane.org/gmane.linux.kernel/481689/focus=3375
Cc: Mohan Kumar M <mohan@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simon Horman [Tue, 20 Feb 2007 21:58:06 +0000 (13:58 -0800)]
[PATCH] Update OSDL/Linux-Foundation maintainer addresses
The patch below updates MAINTAIER address
Individuals (Only Andrew :): osdl.org -> linux-foundation.org
Lists: osdl.org -> lists.osdl.org
I assume the latter will change at some stage, but at least
with this change the osdl/linux-foundation lists are consistent.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Koeller [Tue, 20 Feb 2007 21:58:05 +0000 (13:58 -0800)]
[PATCH] 8250: Fix GCC4 signed/unsigned mismatch warning
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Tue, 20 Feb 2007 21:58:05 +0000 (13:58 -0800)]
[PATCH] cdrom: use unsigned bitfields
Fix 23 of these sparse warnings on x86_64 allmodconfig:
include/linux/cdrom.h:942:19: error: dubious bitfield without explicit
`signed' or `unsigned'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Tue, 20 Feb 2007 21:58:05 +0000 (13:58 -0800)]
[PATCH] tty: use NULL for ptrs
Fix sparse warning in tty_io:
drivers/char/tty_io.c:1536:34: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Tue, 20 Feb 2007 21:58:04 +0000 (13:58 -0800)]
[PATCH] kernel-doc: include struct short description in title output
Output of a function or struct in html mode needs to include the short
description from the function/struct name line in the output title line.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 20 Feb 2007 21:58:01 +0000 (13:58 -0800)]
[PATCH] mfd: SM501 core driver
This driver provides the core functionality of the SM501, which is a
multi-function chip including two framebuffers, video acceleration, USB,
and many other peripheral blocks.
The driver exports a number of entries for the peripheral drivers to use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jarek Poplawski [Tue, 20 Feb 2007 21:58:00 +0000 (13:58 -0800)]
[PATCH] lockdep: debug_locks check after check_chain_key
In __lock_acquire check_chain_key can turn off debug_locks, so check is
needed to assure proper return code.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Miguel Ojeda [Tue, 20 Feb 2007 21:58:00 +0000 (13:58 -0800)]
[PATCH] cfag12864b: fix crash when built-in and no parport present
The problem comes when ks0108/cfag12864b are built-in and no parallel port is
present. ks0108_init() is called first, as it should be, but fails to load
(as there is no parallel port to use).
After that, cfag12864b_init() gets called, without knowing anything about
ks0108 failed, and calls ks0108_writecontrol(), which dereferences an
uninitialized pointer.
Init order is OK, I think. The problem is how to stop cfag12864b_init() being
called if ks0108 failed to load. modprobe does it for us, but, how when
built-in?
Signed-off-by: Miguel Ojeda Sandonis <maxextreme@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aneesh Kumar K.V [Tue, 20 Feb 2007 21:57:58 +0000 (13:57 -0800)]
[PATCH] ext[234]: update documentation
Signed-off-by: "Aneesh Kumar K.V" <aneesh.kumar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan [Tue, 20 Feb 2007 21:57:57 +0000 (13:57 -0800)]
[PATCH] mwave: interesting flags savings
Flags from spin_lock_irqsave() are saved into global variable and restored
from it. My gut feeling this is very racy.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gerhard Dirschl [Tue, 20 Feb 2007 21:57:56 +0000 (13:57 -0800)]
[PATCH] pktcdvd: Correctly set cmd_len field in pkt_generic_packet
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=7810 - a silly
copy-paste bug introduced by the latest change.
Signed-off-by: Gerhard Dirschl <gd@spherenet.de>
Cc: Peter Osterlund <petero2@telia.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Tue, 20 Feb 2007 21:57:56 +0000 (13:57 -0800)]
[PATCH] fault injection: split up stacktrace filter Kconfig option
There is no prompt for CONFIG_STACKTRACE, so FAULT_INJECTION cannot be
selected without LOCKDEP enabled. (found by Paolo 'Blaisorblade'
Giarrusso)
In order to fix such broken Kconfig dependency, this patch splits up the
stacktrace filter support for fault injection by new Kconfig option, which
enables to use fault injection on the architecture which doesn't have
general stacktrace support.
Cc: "Paolo 'Blaisorblade' Giarrusso" <blaisorblade@yahoo.it>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OGAWA Hirofumi [Tue, 20 Feb 2007 21:57:55 +0000 (13:57 -0800)]
[PATCH] FAT: DIO-write fallback to normal buffered
If the DIO write on FAT is expanding the size, it will be fail by -EINVAL,
because FAT can't handle it now.
This patch fallback it to the normal buffered-write and would return
success.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Srinivasa Ds [Tue, 20 Feb 2007 21:57:54 +0000 (13:57 -0800)]
[PATCH] kprobes: list all active probes in the system
This patch lists all active probes in the system by scanning through
kprobe_table[]. It takes care of aggregate handlers and prints the type of
the probe. Letter "k" for kprobes, "j" for jprobes, "r" for kretprobes.
It also lists address of the instruction,its symbolic name(function name +
offset) and the module name. One can access this file through
/sys/kernel/debug/kprobes/list.
Output looks like this
=====================
llm40:~/a # cat /sys/kernel/debug/kprobes/list
c0169ae3 r sys_read+0x0
c0169ae3 k sys_read+0x0
c01694c8 k vfs_write+0x0
c0167d20 r sys_open+0x0
f8e658a6 k reiserfs_delete_inode+0x0 reiserfs
c0120f4a k do_fork+0x0
c0120f4a j do_fork+0x0
c0169b4a r sys_write+0x0
c0169b4a k sys_write+0x0
c0169622 r vfs_read+0x0
=================================
[akpm@linux-foundation.org: cleanup]
[ananth@in.ibm.com: sparc build fix]
Signed-off-by: Srinivasa DS <srinivasa@in.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Tue, 20 Feb 2007 21:57:54 +0000 (13:57 -0800)]
[PATCH] fs: fix __block_write_full_page error case buffer submission
Andrew noticed that unlocking the page before submitting all buffers for
writeout could cause problems if the IO completes before we've finished
messing around with the page buffers, and they subsequently get freed.
Even if there were no bug, it is a good idea to bring the error case
into line with the common case here.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric W. Biederman [Tue, 20 Feb 2007 21:57:53 +0000 (13:57 -0800)]
[PATCH] shm: make sysv ipc shared memory use stacked files
The current ipc shared memory code runs into several problems because it
does not quite use files like the rest of the kernel. With the option of
backing ipc shared memory with either hugetlbfs or ordinary shared memory
the problems got worse. With the added support for ipc namespaces things
behaved so unexpected that we now have several bad namespace reference
counting bugs when using what appears at first glance to be a reasonable
idiom.
So to attack these problems and hopefully make the code more maintainable
this patch simply uses the files provided by other parts of the kernel and
builds it's own files out of them. The shm files are allocated in do_shmat
and freed when their reference count drops to zero with their last unmap.
The file and vm operations that we don't want to implement or we don't
implement completely we just delegate to the operations of our backing
file.
This means that we now get an accurate shm_nattch count for we have a
hugetlbfs inode for backing store, and the shm accounting of last attach
and last detach time work as well.
This means that getting a reference to the ipc namespace when we create the
file and dropping the referenece in the release method is now safe and
correct.
This means we no longer need a special case for clearing VM_MAYWRITE
as our file descriptor now only has write permissions when we have
requested write access when calling shmat. Although VM_SHARED is now
cleared as well which I believe is harmless and is mostly likely a
minor bug fix.
By using the same set of operations for both the hugetlb case and regular
shared memory case shmdt is not simplified and made slightly more correct
as now the test "vma->vm_ops == &shm_vm_ops" is 100% accurate in spotting
all shared memory regions generated from sysvipc shared memory.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Lameter [Tue, 20 Feb 2007 21:57:52 +0000 (13:57 -0800)]
[PATCH] slab: reduce size of alien cache to cover only possible nodes
The alien cache is a per cpu per node array allocated for every slab on the
system. Currently we size this array for all nodes that the kernel does
support. For IA64 this is 1024 nodes. So we allocate an array with 1024
objects even if we only boot a system with 4 nodes.
This patch uses "nr_node_ids" to determine the number of possible nodes
supported by a hardware configuration and only allocates an alien cache
sized for possible nodes.
The initialization of nr_node_ids occurred too late relative to the bootstrap
of the slab allocator and so I moved the setup_nr_node_ids() into
free_area_init_nodes().
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Lameter [Tue, 20 Feb 2007 21:57:51 +0000 (13:57 -0800)]
[PATCH] Convert highest_possible_processor_id to nr_cpu_ids
We frequently need the maximum number of possible processors in order to
allocate arrays for all processors. So far this was done using
highest_possible_processor_id(). However, we do need the number of
processors not the highest id. Moreover the number was so far dynamically
calculated on each invokation. The number of possible processors does not
change when the system is running. We can therefore calculate that number
once.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Lameter [Tue, 20 Feb 2007 21:57:51 +0000 (13:57 -0800)]
[PATCH] Replace highest_possible_node_id() with nr_node_ids
highest_possible_node_id() is currently used to calculate the last possible
node idso that the network subsystem can figure out how to size per node
arrays.
I think having the ability to determine the maximum amount of nodes in a
system at runtime is useful but then we should name this entry
correspondingly, it should return the number of node_ids, and the the value
needs to be setup only once on bootup. The node_possible_map does not
change after bootup.
This patch introduces nr_node_ids and replaces the use of
highest_possible_node_id(). nr_node_ids is calculated on bootup when the
page allocators pagesets are initialized.
[deweerdt@free.fr: fix oops]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 20 Feb 2007 21:57:50 +0000 (13:57 -0800)]
[PATCH] mincore warning fix
allnoconfig:
mm/mincore.c: In function 'do_mincore':
mm/mincore.c:122: warning: unused variable 'entry'
Yet another entry in the why-macros-are-wrong encyclopedia.
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KAMEZAWA Hiroyuki [Tue, 20 Feb 2007 21:57:49 +0000 (13:57 -0800)]
[PATCH] fix mempolicy's check on a system with memory-less-node
bind_zonelist() can create zero-length zonelist if there is a
memory-less-node. This patch checks the length of zonelist. If length is
0, returns -EINVAL.
tested on ia64/NUMA with memory-less-node.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 20 Feb 2007 21:57:48 +0000 (13:57 -0800)]
[PATCH] rework reserved major handling
Several people have reported failures in dynamic major device number handling
due to the recent changes in there to avoid handing out the local/experimental
majors.
Rolf reports that this is due to a gcc-4.1.0 bug.
The patch refactors that code a lot in an attempt to provoke the compiler into
behaving.
Cc: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andries Brouwer [Tue, 20 Feb 2007 21:57:47 +0000 (13:57 -0800)]
[PATCH] minix v3: fix superblock definition
Somehow we got the layout of the v3 superblock wrong, which causes crashes due
to overindexing of the buffer_head array in statfs on large fielsystems.
Cc: "Cedric Augonnet" <cedric.augonnet@gmail.com>
Cc: "Daniel Aragones" <danarag@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 20 Feb 2007 21:57:47 +0000 (13:57 -0800)]
[PATCH] xfs warning fix
fs/xfs/linux-2.6/xfs_super.c:903: warning: 'noinline' attribute ignored
Cc: David Chinner <dgc@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ralf Baechle [Tue, 20 Feb 2007 21:57:45 +0000 (13:57 -0800)]
[PATCH] Fix build errors if bitop functions are do {} while macros
If one of clear_bit, change_bit or set_bit is defined as a do { } while (0)
function usage of these functions in parenthesis like
(foo_bit(23, &var))
while be expaned to something like
(do { ... } while (0)}).
resulting in a build error. This patch removes the useless parenthesis.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 20 Feb 2007 20:14:32 +0000 (12:14 -0800)]
Merge branch 'for-linus' of /home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4165/1: S3C24XX: Select CONFIG_NO_IOPORT
[ARM] Fix s3c2410 ALSA audio for typedef elimination
[ARM] Fix ARM AACI ALSA driver
[ARM] fix mach-at91 build breakage
[ARM] Fix jornada720 build errors
[ARM] Fix iop13xx build error
[ARM] Fix build error caused by move of apm
[ARM] 4223/1: ixdp2351 : Fix for a define error
[ARM] 4187/1: iop: unify time implementation across iop32x, iop33x, and iop13xx
[ARM] 4186/1: iop: remove cp6_enable/disable routines
[ARM] 4185/2: entry: introduce get_irqnr_preamble and arch_ret_to_user
Russell King [Tue, 20 Feb 2007 19:13:30 +0000 (19:13 +0000)]
Merge ARM fixes
Linus Torvalds [Tue, 20 Feb 2007 18:26:46 +0000 (10:26 -0800)]
Merge branch 'upstream-linus' of /linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (21 commits)
natsemi: Support Aculab E1/T1 PMXc cPCI carrier cards
natsemi: Add support for using MII port with no PHY
skge: race with workq and RTNL
Replace local random function with random32()
s2io: RTNL and flush_scheduled_work deadlock
8139too: RTNL and flush_scheduled_work deadlock
sis190: RTNL and flush_scheduled_work deadlock
r8169: RTNL and flush_scheduled_work deadlock
[PATCH] ieee80211softmac: Fix setting of initial transmit rates
[PATCH] bcm43xx: OFDM fix for rev 1 cards
[PATCH] bcm43xx: Fix for 4311 and 02/07/07 specification changes
[PATCH] prism54: correct assignment of DOT1XENABLE in WE-19 codepaths
[PATCH] zd1211rw: Readd zd_addr_t cast
[PATCH] bcm43xx: Fix for oops on resume
[PATCH] bcm43xx: Ignore ampdu status reports
[PATCH] wavelan: Use ARRAY_SIZE macro when appropriate
[PATCH] hostap: Use ARRAY_SIZE macro when appropriate
[PATCH] misc-wireless: Use ARRAY_SIZE macro when appropriate
[PATCH] ipw2100: Use ARRAY_SIZE macro when appropriate
[PATCH] bcm43xx: Janitorial change - remove two unused variables
...
Linus Torvalds [Tue, 20 Feb 2007 18:17:32 +0000 (10:17 -0800)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Remove bogus SYSFS dependency
backlight: simplify corgi_bl locking
backlight: Separate backlight properties from backlight ops pointers
backlight: Clean up pmac_backlight handling
backlight: Improve backlight selection for fbdev drivers
backlight: Rework backlight/fb interaction simplifying, lots
backlight: Remove unneeded backlight update_status calls
backlight: Remove uneeded update_status call from chipsfb.c
backlight/fbcon: Add FB_EVENT_CONBLANK
backlight: Fix Kconfig entries
backlight: Remove uneeded nvidia set_power calls
backlight: Convert semaphore -> mutex
backlight: Fix external uses of backlight internal semaphore
backlight: Minor code cleanups for hp680_bl.c
backlight: Minor code cleanups for corgi_bl.c
backlight: Remove excessive (un)likelys
backlight: Remove unneeded owner field
backlight: Fix error handling
backlight: Add Frontpath ProGear HX1050+ driver
backlight: Add maintainer entry
David Brownell [Tue, 20 Feb 2007 05:28:53 +0000 (21:28 -0800)]
[PATCH] ARM: fix mach-at91 build breakage
The rename of the AT91 subtree from mach-at91rm9200 to mach-at91
(to accomodate at91sam926x processors) was incomplete. It needs
this patch to be able to build again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 20 Feb 2007 18:14:29 +0000 (10:14 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[NET] Eliminate user-selectable CONFIG_MV643XX_ETH_[012]
[MIPS] Drop __init from init_8259A()
[MIPS] Fix Kconfig typo bug
[MIPS] Fix double signal on trap and break instruction
[MIPS] sigset_32 has been made redundand by compat_sigset_t.
[MIPS] emma2rh: Remove needless <asm/i8259.h> inclusion.
[MIPS] Add MTD device support for Cobalt
Geert Uytterhoeven [Tue, 20 Feb 2007 14:45:21 +0000 (15:45 +0100)]
[PATCH] tty_register_driver: Remove incorrect and superfluous cast
tty_register_driver: Remove incorrect and superfluous cast (expected and passed
types are both const char *)
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dale Farnsworth [Tue, 20 Feb 2007 12:15:20 +0000 (05:15 -0700)]
[NET] Eliminate user-selectable CONFIG_MV643XX_ETH_[012]
Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware. After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mackerras <paulus@samba.org>
Atsushi Nemoto [Tue, 20 Feb 2007 11:08:45 +0000 (20:08 +0900)]
[MIPS] Drop __init from init_8259A()
init_8259A() is called from i8259A_resume() so should not be marked as
__init. And add some tests for whether 8259A was already initialized
or not.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 8 Feb 2007 12:44:19 +0000 (12:44 +0000)]
[MIPS] Fix Kconfig typo bug
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Tue, 6 Feb 2007 07:02:21 +0000 (16:02 +0900)]
[MIPS] Fix double signal on trap and break instruction
This commit broke gdb, since any BREAK or TRAP instruction cause SIGSEGV.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Sun, 11 Feb 2007 18:22:36 +0000 (18:22 +0000)]
[MIPS] sigset_32 has been made redundand by compat_sigset_t.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Thu, 8 Feb 2007 01:30:29 +0000 (10:30 +0900)]
[MIPS] emma2rh: Remove needless <asm/i8259.h> inclusion.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Tue, 20 Feb 2007 05:11:57 +0000 (14:11 +0900)]
[MIPS] Add MTD device support for Cobalt
This patch has added MTD device support for Cobalt.
Moreover, removes old type FlashROM support.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ben Dooks [Mon, 12 Feb 2007 17:59:35 +0000 (18:59 +0100)]
[ARM] 4165/1: S3C24XX: Select CONFIG_NO_IOPORT
On S3C24XX architecture, select CONFIG_NO_IOPORT
as we only have memory based IO.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jeff Garzik [Tue, 20 Feb 2007 16:28:42 +0000 (11:28 -0500)]
Merge branch 'upstream-jgarzik' of git://git./linux/kernel/git/linville/wireless-2.6 into upstream
Mark Brown [Mon, 19 Feb 2007 20:15:40 +0000 (20:15 +0000)]
natsemi: Support Aculab E1/T1 PMXc cPCI carrier cards
Aculab E1/T1 PMXc cPCI carrier card cards present a natsemi on the cPCI
bus with an oversized EEPROM using a direct MII<->MII connection with no
PHY. This patch adds a new device table entry supporting these cards.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Brown [Mon, 19 Feb 2007 20:15:39 +0000 (20:15 +0000)]
natsemi: Add support for using MII port with no PHY
This patch provides code paths which allow the natsemi driver to use the
external MII port on the chip but ignore any PHYs that may be attached to it.
The link state will be left as it was when the driver started and can be
configured via ethtool. Any PHYs that are present can be accessed via the MII
ioctl()s.
This is useful for systems where the device is connected without a PHY
or where either information or actions outside the scope of the driver
are required in order to use the PHYs.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stephen Hemminger [Fri, 16 Feb 2007 23:37:39 +0000 (15:37 -0800)]
skge: race with workq and RTNL
If a workqueue function that needs RTNL is running when skge_down
is called then a deadlock is possible. Fix by only clearing the timer,
and handling the flush_scheduled_work on removal. This work queue is only
ever used for the old fiber based boards.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ralf Baechle [Fri, 16 Feb 2007 11:55:33 +0000 (11:55 +0000)]
Replace local random function with random32()
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Francois Romieu [Thu, 15 Feb 2007 22:37:50 +0000 (23:37 +0100)]
s2io: RTNL and flush_scheduled_work deadlock
Mantra: don't use flush_scheduled_work with RTNL held.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Francois Romieu [Thu, 15 Feb 2007 22:37:44 +0000 (23:37 +0100)]
8139too: RTNL and flush_scheduled_work deadlock
Your usual dont-flush_scheduled_work-with-RTNL-held stuff.
It is a bit different here since the thread runs permanently
or is only occasionally kicked for recovery depending on the
hardware revision.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Francois Romieu [Thu, 15 Feb 2007 22:37:29 +0000 (23:37 +0100)]
sis190: RTNL and flush_scheduled_work deadlock
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Francois Romieu [Thu, 15 Feb 2007 22:37:21 +0000 (23:37 +0100)]
r8169: RTNL and flush_scheduled_work deadlock
flush_scheduled_work() in net_device->close has a slight tendency
to deadlock with tasks on the workqueue that hold RTNL.
rtl8169_close/down simply need the recovery tasks to not meddle
with the hardware while the device is going down.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Russell King [Tue, 20 Feb 2007 16:11:11 +0000 (16:11 +0000)]
[ARM] Fix s3c2410 ALSA audio for typedef elimination
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 20 Feb 2007 15:44:23 +0000 (15:44 +0000)]
[ARM] Fix ARM AACI ALSA driver
CC [M] sound/arm/aaci.o
sound/arm/aaci.c:729: error: parse error before '*' token
sound/arm/aaci.c:731: warning: function declaration isn't a prototype
...
sound/arm/aaci.c:786: error: parse error before '*' token
sound/arm/aaci.c:786: warning: function declaration isn't a prototype
...
sound/arm/aaci.c:827: error: parse error before '*' token
sound/arm/aaci.c:828: warning: function declaration isn't a prototype
...
sound/arm/aaci.c:845: error: parse error before "aaci_capture_ops"
sound/arm/aaci.c:845: warning: type defaults to `int' in declaration of `aaci_capture_ops'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David Brownell [Tue, 20 Feb 2007 05:28:53 +0000 (21:28 -0800)]
[ARM] fix mach-at91 build breakage
The rename of the AT91 subtree from mach-at91rm9200 to mach-at91
(to accomodate at91sam926x processors) was incomplete. It needs
this patch to be able to build again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 20 Feb 2007 15:23:57 +0000 (15:23 +0000)]
[ARM] Fix jornada720 build errors
kernel/built-in.o: In function `pm_suspend':
utsname_sysctl.c:(.text+0x23008): multiple definition of `pm_suspend'
arch/arm/mach-sa1100/built-in.o:arch/arm/mach-sa1100/sleep.S:(.text+0xf68): first defined here
arm-linux-ld: Warning: size of symbol `pm_suspend' changed from 20 in arch/arm/mach-sa1100/built-in.o to 44 in kernel/built-in.o
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 20 Feb 2007 14:56:51 +0000 (14:56 +0000)]
[ARM] Fix iop13xx build error
CC arch/arm/mach-iop13xx/setup.o
arch/arm/mach-iop13xx/setup.c: In function 'iq8134x_probe_flash_size':
arch/arm/mach-iop13xx/setup.c:210: warning: implicit declaration of function 'ioremap'
arch/arm/mach-iop13xx/setup.c:210: warning: initialization makes pointer from integer without a cast
arch/arm/mach-iop13xx/setup.c:218: warning: implicit declaration of function 'writew'
arch/arm/mach-iop13xx/setup.c:222: warning: implicit declaration of function 'readb'
arch/arm/mach-iop13xx/setup.c:231: warning: implicit declaration of function 'iounmap'
LD .tmp_vmlinux1
arch/arm/mach-iop13xx/built-in.o: In function `iop13xx_platform_init':
iq81340mc.c:(.init.text+0x150): undefined reference to `ioremap'
iq81340mc.c:(.init.text+0x21c): undefined reference to `writew'
iq81340mc.c:(.init.text+0x24c): undefined reference to `writew'
iq81340mc.c:(.init.text+0x254): undefined reference to `iounmap'
iq81340mc.c:(.init.text+0x2c4): undefined reference to `readb'
iq81340mc.c:(.init.text+0x2e8): undefined reference to `readb'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 20 Feb 2007 14:53:28 +0000 (14:53 +0000)]
[ARM] Fix build error caused by move of apm
CC arch/arm/common/sharpsl_pm.o
arch/arm/common/sharpsl_pm.c:30:31: error: asm/apm-emulation.h: No such file or directory
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Richard Purdie [Tue, 20 Feb 2007 12:27:25 +0000 (12:27 +0000)]
backlight: Remove bogus SYSFS dependency
Remove a bogus SYSFS dependency from the backlight class
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Ozzy [Mon, 19 Feb 2007 14:05:42 +0000 (15:05 +0100)]
[ARM] 4223/1: ixdp2351 : Fix for a define error
Fix syntax error for a define in ixdp2351.h
Signed-off-by: ozzy <linux-ozzy@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 20 Feb 2007 10:52:01 +0000 (10:52 +0000)]
[ARM] Merge remaining IOP code
Conflicts:
include/asm-arm/arch-at91rm9200/entry-macro.S
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Richard Purdie [Sat, 10 Feb 2007 23:50:39 +0000 (23:50 +0000)]
backlight: simplify corgi_bl locking
Now update_status has locking, we can remove the mutex from corgi_bl.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Sat, 10 Feb 2007 23:07:48 +0000 (23:07 +0000)]
backlight: Separate backlight properties from backlight ops pointers
Per device data such as brightness belongs to the indivdual device
and should therefore be separate from the the backlight operation
function pointers. This patch splits the two types of data and
allows simplifcation of some code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Sat, 10 Feb 2007 15:04:08 +0000 (15:04 +0000)]
backlight: Clean up pmac_backlight handling
Move the setting/unsetting of pmac_backlight into the
backlight core instead of doing it in each driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
James Simmons [Sat, 10 Feb 2007 14:15:43 +0000 (14:15 +0000)]
backlight: Improve backlight selection for fbdev drivers
Improve backlight selection for fbdev drivers
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Sat, 10 Feb 2007 14:10:33 +0000 (14:10 +0000)]
backlight: Rework backlight/fb interaction simplifying, lots
fb_info->bl_mutex is badly thought out and the backlight class doesn't
need it if the framebuffer/backlight register/unregister order is
consistent, particularly after the backlight locking fixes.
Fix the drivers to use the order:
backlight_device_register()
register_framebuffer()
unregister_framebuffer()
backlight_device_unregister()
and turn bl_mutex into a lock for the bl_curve data only.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Fri, 9 Feb 2007 09:53:56 +0000 (09:53 +0000)]
backlight: Remove unneeded backlight update_status calls
The backlight core listens for blanking events and triggers a
backlight_update_status call so these extra calls are not
needed and can be removed.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Fri, 9 Feb 2007 09:50:47 +0000 (09:50 +0000)]
backlight: Remove uneeded update_status call from chipsfb.c
Remove uneeded update_status call from chipsfb.c since the
backlight core now receives software blanking notifications
too.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Fri, 9 Feb 2007 09:46:45 +0000 (09:46 +0000)]
backlight/fbcon: Add FB_EVENT_CONBLANK
The backlight class wants notification whenever the console is blanked
but doesn't get this when hardware blanking fails and software blanking
is used. Changing FB_EVENT_BLANK to report both would be a behaviour
change which could confuse the console layer so add a new event for
software blanking and have the backlight class listen for both.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Fri, 9 Feb 2007 09:40:30 +0000 (09:40 +0000)]
backlight: Fix Kconfig entries
Currently its possible to build the backlight core as a module yet
compile the drivers into the kernel which gives missing symbols.
Fix.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Fri, 9 Feb 2007 00:34:52 +0000 (00:34 +0000)]
backlight: Remove uneeded nvidia set_power calls
nvidia_bl_set_power isn't needed since the backlight class handles
this by receiving fb events itself and calling update_status so
remove it.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Thu, 8 Feb 2007 22:53:55 +0000 (22:53 +0000)]
backlight: Convert semaphore -> mutex
Convert internal semaphore to a mutex
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Thu, 8 Feb 2007 22:25:09 +0000 (22:25 +0000)]
backlight: Fix external uses of backlight internal semaphore
backlight_device->sem has a very specific use as documented in the
header file. The external users of this are using it for a different
reason, to serialise access to the update_status() method.
backlight users were supposed to implement their own internal
serialisation of update_status() if needed but everyone is doing
things differently and incorrectly. Therefore add a global mutex to
take care of serialisation for everyone, once and for all.
Locking for get_brightness remains optional since most users don't
need it.
Also update the lcd class in a similar way.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Thu, 8 Feb 2007 00:33:24 +0000 (00:33 +0000)]
backlight: Minor code cleanups for hp680_bl.c
Since people use this code as an example, clean it up to
to use platform_*_drvdata instead of a global variable.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Thu, 8 Feb 2007 00:32:14 +0000 (00:32 +0000)]
backlight: Minor code cleanups for corgi_bl.c
Since people use this code as an example, clean it up to
to use platform_*_drvdata and remove an unneeded function.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Dmitry Torokhov [Thu, 8 Feb 2007 00:12:28 +0000 (00:12 +0000)]
backlight: Remove excessive (un)likelys
Remove excessive numbers of (un)likely()s in the backlight core.
There are no hot paths in this code so rely on compiler to do
the right thing.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Thu, 8 Feb 2007 00:06:32 +0000 (00:06 +0000)]
backlight: Remove unneeded owner field
Remove uneeded owner field from backlight_properties structure.
Nothing uses it and it is unlikely that it will ever be used. The
backlight class uses other means to ensure that nothing references
unloaded code.
Based on a patch from Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Dmitry Torokhov [Wed, 7 Feb 2007 22:25:50 +0000 (22:25 +0000)]
backlight: Fix error handling
Fix error handling when registering new device
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Marcin Juszkiewicz [Wed, 7 Feb 2007 22:24:01 +0000 (22:24 +0000)]
backlight: Add Frontpath ProGear HX1050+ driver
Add control of LCD backlight for Frontpath ProGear HX1050+.
Patch is based on http://downloads.sf.net/progear/progear-lcd-0.2.tar.gz
driver by M Schacht.
Signed-off-by: Marcin Juszkiewicz <openembedded@hrw.one.pl>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Richard Purdie [Wed, 7 Feb 2007 22:21:07 +0000 (22:21 +0000)]
backlight: Add maintainer entry
Add myself as the backlight class/subsystem maintainer.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Linus Torvalds [Tue, 20 Feb 2007 01:38:33 +0000 (17:38 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Cobalt: Fix UART I/O type
[MIPS] Fixup copy_from_user_inatomic
[MIPS] Fix struct sigcontext for N32 userland
[MIPS] Make some __setup functions static
[MIPS] Declare highstart_pfn, highend_pfn only if CONFIG_HIGHMEM=y
[MIPS] Allow selection of KGDB only on platforms where it's supported.
Yoichi Yuasa [Fri, 9 Feb 2007 03:16:24 +0000 (12:16 +0900)]
[MIPS] Cobalt: Fix UART I/O type
The Cobalt UART is actually connected to memory resource area.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Mon, 19 Feb 2007 16:59:24 +0000 (16:59 +0000)]
[MIPS] Fixup copy_from_user_inatomic
From the
01408c4939479ec46c15aa7ef6e2406be50eeeca log message:
The problem is that when we write to a file, the copy from userspace to
pagecache is first done with preemption disabled, so if the source
address is not immediately available the copy fails *and* *zeros* *the*
*destination*.
This is a problem because a concurrent read (which admittedly is an odd
thing to do) might see zeros rather that was there before the write, or
what was there after, or some mixture of the two (any of these being a
reasonable thing to see).
If the copy did fail, it will immediately be retried with preemption
re-enabled so any transient problem with accessing the source won't
cause an error.
The first copying does not need to zero any uncopied bytes, and doing
so causes the problem. It uses copy_from_user_atomic rather than
copy_from_user so the simple expedient is to change copy_from_user_atomic
to *not* zero out bytes on failure.
< --- end cite --- >
This patch finally implements at least a not so pretty solution by
duplicating the relevant part of __copy_user.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Sat, 17 Feb 2007 15:12:57 +0000 (00:12 +0900)]
[MIPS] Fix struct sigcontext for N32 userland
The kernel use 64-bit for sc_regs[0], and both N32/N64 userland
expects it was 64-bit. But size of 'long' on N32 is actually 32-bit.
So this definition make some confusion. Use __u32 and __u64 for
N32/N64 sigcontext to get rid of this confusion.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Sat, 17 Feb 2007 16:02:14 +0000 (01:02 +0900)]
[MIPS] Make some __setup functions static
This fixes some sparse warnings. ("warning: symbol 'foo' was not
declared. Should it be static?")
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Mon, 19 Feb 2007 15:00:49 +0000 (15:00 +0000)]
[MIPS] Declare highstart_pfn, highend_pfn only if CONFIG_HIGHMEM=y
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Sat, 17 Feb 2007 02:58:39 +0000 (02:58 +0000)]
[MIPS] Allow selection of KGDB only on platforms where it's supported.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Greg Banks [Mon, 19 Feb 2007 23:12:34 +0000 (10:12 +1100)]
[PATCH] Fix a free-wrong-pointer bug in nfs/acl server.
Due to type confusion, when an nfsacl verison 2 'ACCESS' request
finishes and tries to clean up, it calls fh_put on entiredly the
wrong thing and this can cause an oops.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Sat, 17 Feb 2007 19:03:21 +0000 (20:03 +0100)]
[PATCH] tick management: make broadcast dependent on local APIC
The broadcast functionality is only necessary when a local APIC is
available. Make the config switch depend on X86_LOCAL_APIC. This
resolves the mach-voyager breakage introduced by the tick managament
code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Sun, 18 Feb 2007 05:22:39 +0000 (21:22 -0800)]
[PATCH] Declare init_irq_proc before we use it.
powerpc gets:
init/main.c: In function `do_basic_setup':
init/main.c:714: warning: implicit declaration of function `init_irq_proc'
but we cannot include linux/irq.h in generic code.
Fix it by moving the declaration into linux/interrupt.h instead.
And make sure all code that defines init_irq_proc() is including
linux/interrupt.h.
And nuke an ifdef-in-C
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Erez Zadok [Mon, 19 Feb 2007 04:57:45 +0000 (23:57 -0500)]
[PATCH] fs/stack.c: Copy i_nlink after all other attributes are copied
A user-specified get_nlinks may depend on other inode attributes.
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Signed-off-by: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Mon, 19 Feb 2007 18:12:05 +0000 (18:12 +0000)]
[PATCH] NOHZ: Produce debug output instead of a BUG()
The BUG_ON() in tick_nohz_stop_sched_tick() triggers on some boxen.
Remove the BUG_ON and print information about the pending softirq
to allow better debugging of the problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Molnar [Mon, 19 Feb 2007 18:11:56 +0000 (18:11 +0000)]
[PATCH] NOHZ: Fix RCU handling
When a CPU is needed for RCU the tick has to continue even when it was
stopped before.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 19 Feb 2007 22:16:51 +0000 (14:16 -0800)]
Merge /linux/kernel/git/wim/linux-2.6-watchdog
* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] machzwd warning fix
Linus Torvalds [Mon, 19 Feb 2007 21:38:42 +0000 (13:38 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Update defconfigs
[MIPS] Support for several more SNI RM models.
[MIPS] Include <asm/bugs> to for declaration of check_bugs32.
[MIPS] Add external declaration of pagetable_init() to pgalloc.h
[MIPS] Make kernel_thread_helper() static
[MIPS] Make __declare_dbe_table static and avoid it getting optimized away
[MIPS] Use MIPS R2 instructions for bitops.
[MIPS] signals: Share even more code.
[MIPS] Fix CONFIG_MIPS32_N32=y CONFIG_MIPS32_O32=n build
[MIPS] Iomap implementation.
[MIPS] <asm/compat-signal.h> needs to include <asm/uaccess.h>.
[MIPS] IP27: Fix warning.
[MIPS] Fix sigset_t endianess swapping issues in 32-bit compat code.
Linus Torvalds [Mon, 19 Feb 2007 21:36:16 +0000 (13:36 -0800)]
Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon/vt1211: Add probing of alternate config index port
hwmon/
f71805f: Fix a race condition
hwmon/abituguru: Fix unchecked return status
hwmon: New driver for the Analog Devices ADM1029
hwmon/w83627ehf: Add support for the W83627DHG chip
hwmon: Use subsys_initcall
hwmon/lm70: Make lm70_remove a __devexit function
hwmon: Cleanup a bogus legacy comment
hwmon: Simplify the locking model of two drivers
hwmon: Drop unused mutexes in two drivers
hwmon/it87: Add PWM base frequency control
Linus Torvalds [Mon, 19 Feb 2007 21:34:11 +0000 (13:34 -0800)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (49 commits)
[MTD] [NAND] S3C2412 fix hw ecc
[MTD] [NAND] Work around false compiler warning in CAFÉ driver
[JFFS2] printk warning fixes
[MTD] [MAPS] ichxrom warning fix
[MTD] [MAPS] amd76xrom warning fix
[MTD] [MAPS] esb2rom warning fixes
[MTD] [MAPS] ck804xrom warning fix
[MTD] [MAPS] netsc520 warning fix
[MTD] [MAPS] sc520cdp warning fix
[MTD] [ONENAND] onenand_base warning fix
[MTD] [NAND] eXcite nand flash driver
[MTD] Improve heuristic for detecting wrong-endian RedBoot partition table
[MTD] Fix RedBoot partition parsing regression harder.
[MTD] [NAND] S3C2410: Hardware ECC correction code
[JFFS2] Use MTD_OOB_AUTO to automatically place cleanmarker on NAND
[MTD] Clarify OOB-operation interface comments
[MTD] remove unused ecctype,eccsize fields from struct mtd_info
[MTD] [NOR] Intel: remove ugly PROGREGION macros
[MTD] [NOR] STAA: use writesize instead off eccsize to represent ECC block
[MTD] OneNAND: Invalidate bufferRAM after erase
...
Linus Torvalds [Mon, 19 Feb 2007 21:33:01 +0000 (13:33 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: implement optional loose read cache
9p: Use kthread_stop instead of sending a SIGKILL.
Linus Torvalds [Mon, 19 Feb 2007 21:32:28 +0000 (13:32 -0800)]
Merge /pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] SCSI core: better initialization for sdev->scsi_level
[SCSI] scsi_proc.c: display sdev->scsi_level correctly
[SCSI] megaraid_sas: update version and author info
[SCSI] megaraid_sas: return sync cache call with success
[SCSI] megaraid_sas: replace pci_alloc_consitent with dma_alloc_coherent in ioctl path
[SCSI] megaraid_sas: add bios_param in scsi_host_template
[SCSI] megaraid_sas: do not process cmds if hw_crit_error is set
[SCSI] scsi_transport.h should include scsi_device.h
[SCSI] aic79xx: remove extra newline from info message
[SCSI] scsi_scan.c: handle bad inquiry responses
[SCSI] aic94xx: tie driver to the major number of the sequencer firmware
[SCSI] lpfc: add PCI error recovery support
[SCSI] megaraid: pci_module_init to pci_register_driver
[SCSI] tgt: fix the user/kernel ring buffer interface
[SCSI] sgiwd93: interfacing to wd33c93
[SCSI] wd33c93: Fast SCSI with WD33C93B
Linus Torvalds [Mon, 19 Feb 2007 21:31:34 +0000 (13:31 -0800)]
Merge branch 'for-linus' of /linux/kernel/git/dtor/input
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input:
Input: remove obsolete setup parameters from input drivers
Input: HIL - fix improper call to release_region()
Input: hid-lgff - treat devices as joysticks unless told otherwise
Input: HID - add support for Logitech Formula Force EX
Input: gpio-keys - switch to common GPIO API
Input: do not lock device when showing name, phys and uniq
Input: i8042 - let serio bus suspend ports
Input: psmouse - properly reset mouse on shutdown/suspend