OSDN Git Service
Jon Mason [Thu, 24 Jun 2010 18:45:10 +0000 (18:45 +0000)]
s2io: add dynamic LRO disable support
This patch adds dynamic LRO disable support for s2io net driver,
enables LRO by default, increases the driver version number, and
corrects the name of the LRO modparm.
This is mostly Wang's patch based on Neil's initial work, heavily
modified based on Ramkrishna's suggestions. This has been tested on
a Neterion Xframe adapter and verified via adapter LRO statistics.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Neil Horman <nhorman@redhat.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Ramkrishna Vepa <Ramkrishna.Vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 21 Jun 2010 11:48:45 +0000 (11:48 +0000)]
syncookies: add support for ECN
Allows use of ECN when syncookies are in effect by encoding ecn_ok
into the syn-ack tcp timestamp.
While at it, remove a uneeded #ifdef CONFIG_SYN_COOKIES.
With CONFIG_SYN_COOKIES=nm want_cookie is ifdef'd to 0 and gcc
removes the "if (0)".
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Mon, 21 Jun 2010 11:48:44 +0000 (11:48 +0000)]
syncookies: do not store rcv_wscale in tcp timestamp
As pointed out by Fernando Gont there is no need to encode rcv_wscale
into the cookie.
We did not use the restored rcv_wscale anyway; it is recomputed
via tcp_select_initial_window().
Thus we can save 4 bits in the ts option space by removing rcv_wscale.
In case window scaling was not supported, we set the (invalid) wscale
value 0xf.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 23 Jun 2010 02:51:25 +0000 (02:51 +0000)]
ipv6: remove ipv6_statistics
commit
9261e5370112 (ipv6: making ip and icmp statistics per/namespace)
forgot to remove ipv6_statistics variable.
commit
bc417d99bf27 (ipv6: remove stale MIB definitions) took care of
icmpv6_statistics & icmpv6msg_statistics
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Denis V. Lunev <den@openvz.org>
CC: Alexey Dobriyan <adobriyan@gmail.com>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 22 Jun 2010 20:58:41 +0000 (20:58 +0000)]
snmp: add align parameter to snmp_mib_init()
In preparation for 64bit snmp counters for some mibs,
add an 'align' parameter to snmp_mib_init(), instead
of assuming mibs only contain 'unsigned long' fields.
Callers can use __alignof__(type) to provide correct
alignment.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 22 Jun 2010 12:44:11 +0000 (12:44 +0000)]
loopback: use u64_stats_sync infrastructure
Commit
6b10de38f0ef (loopback: Implement 64bit stats on 32bit arches)
introduced 64bit stats in loopback driver, using a private seqcount and
private helpers.
David suggested to introduce a generic infrastructure, added in (net:
Introduce u64_stats_sync infrastructure)
This patch reimplements loopback 64bit stats using the u64_stats_sync
infrastructure.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 22 Jun 2010 07:43:15 +0000 (07:43 +0000)]
arp: RCU change in arp_solicit()
Avoid two atomic ops in arp_solicit()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Tue, 22 Jun 2010 01:14:35 +0000 (01:14 +0000)]
dccp: make implementation of Syn-RTT symmetric
This patch is thanks to Andre Noll who reported the issue and helped testing.
The Syn-RTT sampled during the initial handshake currently only works for
the client sending the DCCP-Request. TFRC penalizes the absence of an RTT
sample with a very slow initial speed (1 packet per second), which delays
slow-start significantly, resulting in sluggish performance.
This patch mirrors the "Syn RTT" principle by adding a timestamp also onto
the DCCP-Response, producing an RTT sample when the (Data)Ack completing
the handshake arrives.
Also changed the documentation to 'TFRC' since Syn RTTs are also used by CCID-4.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Tue, 22 Jun 2010 01:14:34 +0000 (01:14 +0000)]
dccp: remove unused function argument
This removes an unused 'sk' argument from several option-inserting functions.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Benard [Fri, 18 Jun 2010 04:19:54 +0000 (04:19 +0000)]
net/fec: clean suspend/resume
Commit
59d4289b83b11379d867e2f7146904b19cc96404 converted fec to dev_pm_ops but
didn't update the suspend/resume functions thus leading to the following warning :
"initialization from incompatible pointer type" when CONFIG_PM is set.
This patch also fixe a few indentation and style around CONFIG_PM area.
Signed-off-by: Eric BĂ©nard <eric@eukrea.com>
Cc: netdev@vger.kernel.org
Cc: davem@davemloft.net
Cc: amit.kucheria@canonical.com
Cc: s.hauer@pengutronix.de
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Divy Le Ray [Mon, 21 Jun 2010 15:54:53 +0000 (15:54 +0000)]
cxgb3: request 7.10 firmware
The driver requests FW 7.10
Bump up driver version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divy Le Ray [Mon, 21 Jun 2010 15:54:48 +0000 (15:54 +0000)]
cxgb3: update FW to 7.10
Update FW to 7.10
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Mon, 21 Jun 2010 12:29:14 +0000 (12:29 +0000)]
net/core/pktgen.c: Use pr_<level>
Add pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove "pktgen: " from formats
Convert printks to pr_<level>
Added func_enter() for debugging
Moved version to end of string at module_init
Coalesced long formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hagen Paul Pfeifer [Sat, 19 Jun 2010 17:05:36 +0000 (17:05 +0000)]
net: optimize Berkeley Packet Filter (BPF) processing
Gcc is currenlty not in the ability to optimize the switch statement in
sk_run_filter() because of dense case labels. This patch replace the
OR'd labels with ordered sequenced case labels. The sk_chk_filter()
function is modified to patch/replace the original OPCODES in a
ordered but equivalent form. gcc is now in the ability to transform the
switch statement in sk_run_filter into a jump table of complexity O(1).
Until this patch gcc generates a sequence of conditional branches (O(n) of 567
byte .text segment size (arch x86_64):
7ff: 8b 06 mov (%rsi),%eax
801: 66 83 f8 35 cmp $0x35,%ax
805: 0f 84 d0 02 00 00 je adb <sk_run_filter+0x31d>
80b: 0f 87 07 01 00 00 ja 918 <sk_run_filter+0x15a>
811: 66 83 f8 15 cmp $0x15,%ax
815: 0f 84 c5 02 00 00 je ae0 <sk_run_filter+0x322>
81b: 77 73 ja 890 <sk_run_filter+0xd2>
81d: 66 83 f8 04 cmp $0x4,%ax
821: 0f 84 17 02 00 00 je a3e <sk_run_filter+0x280>
827: 77 29 ja 852 <sk_run_filter+0x94>
829: 66 83 f8 01 cmp $0x1,%ax
[...]
With the modification the compiler translate the switch statement into
the following jump table fragment:
7ff: 66 83 3e 2c cmpw $0x2c,(%rsi)
803: 0f 87 1f 02 00 00 ja a28 <sk_run_filter+0x26a>
809: 0f b7 06 movzwl (%rsi),%eax
80c: ff 24 c5 00 00 00 00 jmpq *0x0(,%rax,8)
813: 44 89 e3 mov %r12d,%ebx
816: e9 43 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
81b: 41 89 dc mov %ebx,%r12d
81e: e9 3b 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
Furthermore, I reordered the instructions to reduce cache line misses by
order the most common instruction to the start.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Fri, 25 Jun 2010 07:06:29 +0000 (07:06 +0000)]
sfc: Log clearer error messages for hardware monitor
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Fri, 25 Jun 2010 07:05:56 +0000 (07:05 +0000)]
sfc: Use Toeplitz IPv4 hash for RSS and hash insertion
Insertion of the Falcon hash is unreliable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Fri, 25 Jun 2010 07:05:43 +0000 (07:05 +0000)]
sfc: Move siena_nic_data::ipv6_rss_key to efx_nic::rx_hash_key
We will use this hash key for Toeplitz IPv4 hashing too.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Fri, 25 Jun 2010 07:05:33 +0000 (07:05 +0000)]
sfc: Fix reading of inserted hash
The hash appears immediately before the packet data, not at the
beginning of the buffer. This means we can easily use negative offsets
from the start of packet data, so adjust the data and length at the
top of __efx_rx_packet() instead of wherever we consume the hash.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:52:26 +0000 (10:52 +0000)]
enic: Clean ups
1) Update copyright
2) Fix hardware queue descriptor field size CQ_ENET_RQ_DESC_FCOE_SOF_BITS
3) Include rtnetlink.h instead of if_link.h
4) Selectively flush writes to interrupt mask register
5) Use pci_enable_device_mem
6) Remove unused variables and header files
7) Fix size mismatch between memory alloc and free operations of a variable
8) Check for non null arguments to vic_provinfo_alloc
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:52:08 +0000 (10:52 +0000)]
enic: Bug Fix: Handle surprise hardware removals
Handle surprise hardware removals gracefully during devcmd issue and init,
cleanup of queues.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:51:59 +0000 (10:51 +0000)]
enic: Feature Add: Add loopback capability to enic devices
Hardware has the loopback capability to queue the packets transmitted from
a device to the receive queue of the same device. enic now supports the
loopback capability.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:51:51 +0000 (10:51 +0000)]
enic: Use receive queue buffer blocks of 32/64 entries
Change the receive queue buffer allocations into blocks of 32 entries when
ring size is less than 64, otherwise use 64 entries per block.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:51:43 +0000 (10:51 +0000)]
enic: Add new firmware devcmds
Add new firmware devcmds - CMD_PROXY_BY_BDF, CMD_PACKET_FILTER_ALL,
CMD_ENABLE_WAIT.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:50:56 +0000 (10:50 +0000)]
enic: Use (netdev|dev|pr)_<level> macro helpers for logging
Replace all printk routines with the (netdev|dev|pr)_<level> macros that
provide verbose logs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:50:12 +0000 (10:50 +0000)]
enic: Clean up: Add wrapper routines for firmware devcmd calls
Add wrapper routines that issue devcmds to firmware and ensure that a
devcmd lock is held for each devcmd call.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:50:00 +0000 (10:50 +0000)]
enic: Use a lighter reset operation for enic devices
The port profile information for a dynamic enic device is set by the upper
layers, that are oblivious to the device reset operation. We do not want a
reset operation erase the network state of a dynamic enic device as there
is no way to set up the port profile information again. Hence a lighter
reset operation called hang reset is used. Hang reset, unlike soft reset
does not reset the network state and resets the host side state only.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:49:51 +0000 (10:49 +0000)]
enic: Bug Fix: Change hardware ingress vlan rewrite mode
The current ingress vlan rewrite mode setting lets the hardware strip off
the tag control information of a packet received on native vlan. As a
result, the priority bits are also lost. The fix is to change the ingress
vlan rewrite mode setting such that the complete tag control information is
retained for packets that belong to native vlan.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasanthy Kolluri [Thu, 24 Jun 2010 10:49:25 +0000 (10:49 +0000)]
enic: Feature Add: Replace LRO with GRO
enic now uses the GRO mechanism instead of LRO to pass skbs to upper
layers.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 24 Jun 2010 14:58:42 +0000 (14:58 +0000)]
cnic: Update version to 2.1.3.
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 24 Jun 2010 14:58:41 +0000 (14:58 +0000)]
cnic: Further unify kcq handling code.
This eliminates some of the duplicate code for the various devices
that require the same basic kcq handling.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 24 Jun 2010 14:58:40 +0000 (14:58 +0000)]
cnic: Restructure kcq processing.
By doing more work in the common function cnic_get_kcqes(), and
making full use of the kcq_info structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 24 Jun 2010 14:58:39 +0000 (14:58 +0000)]
cnic: Unify kcq allocation for all devices.
By creating a common data stucture kcq_info for all devices, the kcq
(kernel completion queue) for all devices can be allocated by common
code.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 24 Jun 2010 14:58:38 +0000 (14:58 +0000)]
cnic: Unify IRQ code for all hardware types.
By creating a common cnic_doirq().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 24 Jun 2010 14:58:37 +0000 (14:58 +0000)]
cnic: Fine-tune CID memory space calculation.
The current code makes assumptions about the CID (context ID) memory
space and starting CID that may not be always correct when firmware
changes. In particular, BNX2_ISCSI_START_CID may not always be fixed.
We now calculate cp->max_cid_space and cp->iscsi_start_cid dynamically
instead of using fixed constants. The unused cp->max_iscsi_conn is also
eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 23 Jun 2010 11:31:28 +0000 (11:31 +0000)]
sfc: Record hardware RX hash on each skb where possible
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 23 Jun 2010 11:30:35 +0000 (11:30 +0000)]
sfc: Disable setting feature flags that are not implemented
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 23 Jun 2010 11:30:26 +0000 (11:30 +0000)]
sfc: Replace EFX_DRIVER_NAME with KBUILD_MODNAME
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 23 Jun 2010 11:30:07 +0000 (11:30 +0000)]
sfc: Implement message level control
Replace EFX_ERR() with netif_err(), EFX_INFO() with netif_info(),
EFX_LOG() with netif_dbg() and EFX_TRACE() and EFX_REGDUMP() with
netif_vdbg().
Replace EFX_ERR_RL(), EFX_INFO_RL() and EFX_LOG_RL() using explicit
calls to net_ratelimit().
Implement the ethtool operations to get and set message level flags,
and add a 'debug' module parameter for the initial value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 23 Jun 2010 11:29:24 +0000 (11:29 +0000)]
sfc: Log MTD errors using partition name, not just net device name
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 21 Jun 2010 03:06:53 +0000 (03:06 +0000)]
sfc: Implement ethtool register dump operation
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Konstantin Khorenko [Fri, 25 Jun 2010 04:54:58 +0000 (21:54 -0700)]
tcp: do not send reset to already closed sockets
i've found that tcp_close() can be called for an already closed
socket, but still sends reset in this case (tcp_send_active_reset())
which seems to be incorrect. Moreover, a packet with reset is sent
with different source port as original port number has been already
cleared on socket. Besides that incrementing stat counter for
LINUX_MIB_TCPABORTONCLOSE also does not look correct in this case.
Initially this issue was found on 2.6.18-x RHEL5 kernel, but the same
seems to be true for the current mainstream kernel (checked on
2.6.35-rc3). Please, correct me if i missed something.
How that happens:
1) the server receives a packet for socket in TCP_CLOSE_WAIT state
that triggers a tcp_reset():
Call Trace:
<IRQ> [<
ffffffff8025b9b9>] tcp_reset+0x12f/0x1e8
[<
ffffffff80046125>] tcp_rcv_state_process+0x1c0/0xa08
[<
ffffffff8003eb22>] tcp_v4_do_rcv+0x310/0x37a
[<
ffffffff80028bea>] tcp_v4_rcv+0x74d/0xb43
[<
ffffffff8024ef4c>] ip_local_deliver_finish+0x0/0x259
[<
ffffffff80037131>] ip_local_deliver+0x200/0x2f4
[<
ffffffff8003843c>] ip_rcv+0x64c/0x69f
[<
ffffffff80021d89>] netif_receive_skb+0x4c4/0x4fa
[<
ffffffff80032eca>] process_backlog+0x90/0xec
[<
ffffffff8000cc50>] net_rx_action+0xbb/0x1f1
[<
ffffffff80012d3a>] __do_softirq+0xf5/0x1ce
[<
ffffffff8001147a>] handle_IRQ_event+0x56/0xb0
[<
ffffffff8006334c>] call_softirq+0x1c/0x28
[<
ffffffff80070476>] do_softirq+0x2c/0x85
[<
ffffffff80070441>] do_IRQ+0x149/0x152
[<
ffffffff80062665>] ret_from_intr+0x0/0xa
<EOI> [<
ffffffff80008a2e>] __handle_mm_fault+0x6cd/0x1303
[<
ffffffff80008903>] __handle_mm_fault+0x5a2/0x1303
[<
ffffffff80033a9d>] cache_free_debugcheck+0x21f/0x22e
[<
ffffffff8006a263>] do_page_fault+0x49a/0x7dc
[<
ffffffff80066487>] thread_return+0x89/0x174
[<
ffffffff800c5aee>] audit_syscall_exit+0x341/0x35c
[<
ffffffff80062e39>] error_exit+0x0/0x84
tcp_rcv_state_process()
... // (sk_state == TCP_CLOSE_WAIT here)
...
/* step 2: check RST bit */
if(th->rst) {
tcp_reset(sk);
goto discard;
}
...
---------------------------------
tcp_rcv_state_process
tcp_reset
tcp_done
tcp_set_state(sk, TCP_CLOSE);
inet_put_port
__inet_put_port
inet_sk(sk)->num = 0;
sk->sk_shutdown = SHUTDOWN_MASK;
2) After that the process (socket owner) tries to write something to
that socket and "inet_autobind" sets a _new_ (which differs from
the original!) port number for the socket:
Call Trace:
[<
ffffffff80255a12>] inet_bind_hash+0x33/0x5f
[<
ffffffff80257180>] inet_csk_get_port+0x216/0x268
[<
ffffffff8026bcc9>] inet_autobind+0x22/0x8f
[<
ffffffff80049140>] inet_sendmsg+0x27/0x57
[<
ffffffff8003a9d9>] do_sock_write+0xae/0xea
[<
ffffffff80226ac7>] sock_writev+0xdc/0xf6
[<
ffffffff800680c7>] _spin_lock_irqsave+0x9/0xe
[<
ffffffff8001fb49>] __pollwait+0x0/0xdd
[<
ffffffff8008d533>] default_wake_function+0x0/0xe
[<
ffffffff800a4f10>] autoremove_wake_function+0x0/0x2e
[<
ffffffff800f0b49>] do_readv_writev+0x163/0x274
[<
ffffffff80066538>] thread_return+0x13a/0x174
[<
ffffffff800145d8>] tcp_poll+0x0/0x1c9
[<
ffffffff800c56d3>] audit_syscall_entry+0x180/0x1b3
[<
ffffffff800f0dd0>] sys_writev+0x49/0xe4
[<
ffffffff800622dd>] tracesys+0xd5/0xe0
3) sendmsg fails at last with -EPIPE (=> 'write' returns -EPIPE in userspace):
F: tcp_sendmsg1 -EPIPE: sk=
ffff81000bda00d0, sport=49847, old_state=7, new_state=7, sk_err=0, sk_shutdown=3
Call Trace:
[<
ffffffff80027557>] tcp_sendmsg+0xcb/0xe87
[<
ffffffff80033300>] release_sock+0x10/0xae
[<
ffffffff8016f20f>] vgacon_cursor+0x0/0x1a7
[<
ffffffff8026bd32>] inet_autobind+0x8b/0x8f
[<
ffffffff8003a9d9>] do_sock_write+0xae/0xea
[<
ffffffff80226ac7>] sock_writev+0xdc/0xf6
[<
ffffffff800680c7>] _spin_lock_irqsave+0x9/0xe
[<
ffffffff8001fb49>] __pollwait+0x0/0xdd
[<
ffffffff8008d533>] default_wake_function+0x0/0xe
[<
ffffffff800a4f10>] autoremove_wake_function+0x0/0x2e
[<
ffffffff800f0b49>] do_readv_writev+0x163/0x274
[<
ffffffff80066538>] thread_return+0x13a/0x174
[<
ffffffff800145d8>] tcp_poll+0x0/0x1c9
[<
ffffffff800c56d3>] audit_syscall_entry+0x180/0x1b3
[<
ffffffff800f0dd0>] sys_writev+0x49/0xe4
[<
ffffffff800622dd>] tracesys+0xd5/0xe0
tcp_sendmsg()
...
/* Wait for a connection to finish. */
if ((1 << sk->sk_state) & ~(TCPF_ESTABLISHED | TCPF_CLOSE_WAIT)) {
int old_state = sk->sk_state;
if ((err = sk_stream_wait_connect(sk, &timeo)) != 0) {
if (f_d && (err == -EPIPE)) {
printk("F: tcp_sendmsg1 -EPIPE: sk=%p, sport=%u, old_state=%d, new_state=%d, "
"sk_err=%d, sk_shutdown=%d\n",
sk, ntohs(inet_sk(sk)->sport), old_state, sk->sk_state,
sk->sk_err, sk->sk_shutdown);
dump_stack();
}
goto out_err;
}
}
...
4) Then the process (socket owner) understands that it's time to close
that socket and does that (and thus triggers sending reset packet):
Call Trace:
...
[<
ffffffff80032077>] dev_queue_xmit+0x343/0x3d6
[<
ffffffff80034698>] ip_output+0x351/0x384
[<
ffffffff80251ae9>] dst_output+0x0/0xe
[<
ffffffff80036ec6>] ip_queue_xmit+0x567/0x5d2
[<
ffffffff80095700>] vprintk+0x21/0x33
[<
ffffffff800070f0>] check_poison_obj+0x2e/0x206
[<
ffffffff80013587>] poison_obj+0x36/0x45
[<
ffffffff8025dea6>] tcp_send_active_reset+0x15/0x14d
[<
ffffffff80023481>] dbg_redzone1+0x1c/0x25
[<
ffffffff8025dea6>] tcp_send_active_reset+0x15/0x14d
[<
ffffffff8000ca94>] cache_alloc_debugcheck_after+0x189/0x1c8
[<
ffffffff80023405>] tcp_transmit_skb+0x764/0x786
[<
ffffffff8025df8a>] tcp_send_active_reset+0xf9/0x14d
[<
ffffffff80258ff1>] tcp_close+0x39a/0x960
[<
ffffffff8026be12>] inet_release+0x69/0x80
[<
ffffffff80059b31>] sock_release+0x4f/0xcf
[<
ffffffff80059d4c>] sock_close+0x2c/0x30
[<
ffffffff800133c9>] __fput+0xac/0x197
[<
ffffffff800252bc>] filp_close+0x59/0x61
[<
ffffffff8001eff6>] sys_close+0x85/0xc7
[<
ffffffff800622dd>] tracesys+0xd5/0xe0
So, in brief:
* a received packet for socket in TCP_CLOSE_WAIT state triggers
tcp_reset() which clears inet_sk(sk)->num and put socket into
TCP_CLOSE state
* an attempt to write to that socket forces inet_autobind() to get a
new port (but the write itself fails with -EPIPE)
* tcp_close() called for socket in TCP_CLOSE state sends an active
reset via socket with newly allocated port
This adds an additional check in tcp_close() for already closed
sockets. We do not want to send anything to closed sockets.
Signed-off-by: Konstantin Khorenko <khorenko@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Baryshkov [Wed, 16 Jun 2010 23:02:24 +0000 (23:02 +0000)]
broadcom: Add 5241 support
This patch adds the 5241 PHY ID to the broadcom module.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Baryshkov [Wed, 16 Jun 2010 23:02:23 +0000 (23:02 +0000)]
broadcom: move all PHY_ID's to header
Move all PHY IDs to brcmphy.h header for completeness and unification of code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton [Fri, 25 Jun 2010 03:33:04 +0000 (20:33 -0700)]
net: fix "netpoll: Allow netpoll_setup/cleanup recursion"
Remove rtnl_unlock() which had no corresponding rtnl_lock().
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 24 Jun 2010 01:26:27 +0000 (18:26 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Conflicts:
net/ipv4/ip_output.c
Brandon Philips [Wed, 16 Jun 2010 16:21:58 +0000 (16:21 +0000)]
sky2: enable rx/tx in sky2_phy_reinit()
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Olsa [Tue, 15 Jun 2010 01:07:31 +0000 (01:07 +0000)]
net - IP_NODEFRAG option for IPv4 socket
this patch is implementing IP_NODEFRAG option for IPv4 socket.
The reason is, there's no other way to send out the packet with user
customized header of the reassembly part.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 21 Jun 2010 22:57:12 +0000 (22:57 +0000)]
qeth: handle missing z/VM authorization of OSX
For z/VM guest operating systems, OSX CHPIDs can only be used, if
LPAR and z/VM userID are explicitly authorized through the Service
Element. Issue a message if this SE-authorization is missing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 21 Jun 2010 22:57:11 +0000 (22:57 +0000)]
qeth: specify correct function level for OSN devices
OSN devices use the same function level as OSD devices. This patch
adds OSN-devices to the initialization function for func_level.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Blaschka [Mon, 21 Jun 2010 22:57:10 +0000 (22:57 +0000)]
qeth: fix page breaks in hw headers
Turning on memory debugging showed there could be page breaks in
hardware headers. OSA does not allow this so we had to add code
to bounce the header in case there is a page break. This patch also
fixes a problem in case the skb->data part of a fragmented skb
spreads multiple pages.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carsten Otte [Mon, 21 Jun 2010 22:57:09 +0000 (22:57 +0000)]
qeth: fix use after free for qeths debug area
The function qeth_free_buffer_pool is called _after_ the per-card
debug area has been released. This debug message is not all that
usefull anyway, and thus gets removed.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carsten Otte [Mon, 21 Jun 2010 22:57:08 +0000 (22:57 +0000)]
qeth: Fold qeth_qerr debug area
This patch removes the qerr debug area. Most info that goes in here is logged
to the card's local debug area already, those duplicates are removed. All other
elements are moved to the card's local debug area.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carsten Otte [Mon, 21 Jun 2010 22:57:07 +0000 (22:57 +0000)]
qeth: Fold qeth_misc debug area
This patch removes the misc debug area. Instead of logging the entire skb
we just log a pointer to it into the card's local debug area in
qeth_core_get_next_skb. Other then that, this debug area is not used anywhere.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carsten Otte [Mon, 21 Jun 2010 22:57:06 +0000 (22:57 +0000)]
qeth: Fold qeth_sense debug area
This patch removes the sense debug area completely. Despite the name this
debug area makes no sense at all because it's unused completely. Ouch.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carsten Otte [Mon, 21 Jun 2010 22:57:05 +0000 (22:57 +0000)]
qeth: Fold qeth_trace debug area
This patch removes the qeth_trace debug area. All relevant data is logged into
either qeth_setup or into each card's own debug area. Superfluous information
(such as the card number when logging into the card's own debug area) is
removed without replacement.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carsten Otte [Mon, 21 Jun 2010 22:57:04 +0000 (22:57 +0000)]
qeth: Add new s390 debug feature for each qeth card
This patch adds a debug area for each qeth card. This debug area will replace
various other debug areas that are global for all cards handled by the device
driver. On crash dump analysis this makes life easier when trying to find out
what's going on with an interface. Also, the forest of debug areas for this
device driver is significantly cleared up.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carsten Otte [Mon, 21 Jun 2010 22:57:03 +0000 (22:57 +0000)]
qeth: Rework qeth_dbf_longtext
This patch decouples qeth_dbf_longtext from qeth's static debug array. The
function only uses one member anyway.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Mon, 21 Jun 2010 22:57:02 +0000 (22:57 +0000)]
smsgiucv: guarantee single iucv connect in thaw
If another smsgiucv_app device exists, suspend / resume fails with
iucv path list corruption, because the same iucv_path_connect is
called twice.
The patch introduces a flag to save connect status of the smsgiucv
path to make sure iucv_path_connect in smsg_pm_restore_thaw is
called only once.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Tue, 22 Jun 2010 03:19:05 +0000 (03:19 +0000)]
qlcnic: update version to 5.0.6
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Tue, 22 Jun 2010 03:19:04 +0000 (03:19 +0000)]
qlcnic: mark context state freed after destroy
After destroying recv ctx, context state remain same.
Fix it by marking as FREED.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Tue, 22 Jun 2010 03:19:03 +0000 (03:19 +0000)]
qlcnic: offload tx timeout recovery
Offload tx timeout recovery to fw recovery func(check_health).
In check_health, first check health of device, if it its ok, then
do tx timeout recovery otherwise device recovery.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Tue, 22 Jun 2010 03:19:02 +0000 (03:19 +0000)]
qlcnic: dont free host resources during fw recovery
There is no need to free/alloc host resources during firmware
recovery.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Tue, 22 Jun 2010 03:19:01 +0000 (03:19 +0000)]
qlcnic: release device resources during interface down
Previously we were allocating device resources during probe and
release them during remove.
Now alloc during interface up and release in interface down.
This helps in device performance, as it doesn't need to keep
track of inactive resources.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Tue, 22 Jun 2010 03:19:00 +0000 (03:19 +0000)]
qlcnic: fix mac address mgmt
We first add mac address in driver local list and then send command to
fw to add same. There are checks in driver to ensure send command doesn't fail
before adding mac address in local list.
But instead fix should be:
Add mac address in fw and if it succeeds, add it in driver local list.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Tue, 22 Jun 2010 03:18:59 +0000 (03:18 +0000)]
qlcnic: handshake with card after fw load
Instead of delaying rcv handshake till interface comes up,
do it just after fw load.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Tue, 22 Jun 2010 03:18:58 +0000 (03:18 +0000)]
qlcnic: cleanup skb allocation
No need to maintian separate state for alloced and freed skb.
This can be done by null check.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 23 Jun 2010 20:00:48 +0000 (13:00 -0700)]
bridge: 64bit rx/tx counters
Use u64_stats_sync infrastructure to provide 64bit rx/tx
counters even on 32bit hosts.
It is safe to use a single u64_stats_sync for rx and tx,
because BH is disabled on both, and we use per_cpu data.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 22 Jun 2010 17:22:17 +0000 (10:22 -0700)]
net: Introduce u64_stats_sync infrastructure
To properly implement 64bits network statistics on 32bit or 64bit hosts,
we provide one new type and four methods, to ease conversions.
Stats producer should use following template granted it already got an
exclusive access to counters (include/linux/u64_stats_sync.h contains
some documentation about details)
u64_stats_update_begin(&stats->syncp);
stats->bytes64 += len;
stats->packets64++;
u64_stats_update_end(&stats->syncp);
While a consumer should use following template to get consistent
snapshot :
u64 tbytes, tpackets;
unsigned int start;
do {
start = u64_stats_fetch_begin(&stats->syncp);
tbytes = stats->bytes64;
tpackets = stats->packets64;
} while (u64_stats_fetch_retry(&stats->lock, syncp));
Suggested by David Miller, and comments courtesy of Nick Piggin.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Wed, 16 Jun 2010 14:18:12 +0000 (14:18 +0000)]
net: consolidate netif_needs_gso() checks
netif_needs_gso() is checked twice in the TX path once,
before submitting the skb to the qdisc and once after
it is dequeued from the qdisc just before calling
ndo_hard_start(). This opens a window for a user to
change the gso/tso or tx checksum settings that can
cause netif_needs_gso to be true in one check and false
in the other.
Specifically, changing TX checksum setting may cause
the warning in skb_gso_segment() to be triggered if
the checksum is calculated earlier.
This consolidates the netif_needs_gso() calls so that
the stack only checks if gso is needed in
dev_hard_start_xmit().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Justin P. Mattock [Mon, 21 Jun 2010 20:45:42 +0000 (13:45 -0700)]
net: Fix a typo in netlink.h
Fix a typo in include/net/netlink.h
should be finalize instead of finanlize
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Thu, 17 Jun 2010 18:59:48 +0000 (18:59 +0000)]
e1000e: disable gig speed when in S0->Sx transition
Most of this workaround is necessary for all ICHx/PCH parts so one of
the two MAC-type checks can be removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Thu, 17 Jun 2010 18:59:27 +0000 (18:59 +0000)]
e1000e: packet split should not be used with early receive
Originally it was thought there were issues with ICHx/PCH parts with packet
split when jumbo frames were enabled but in fact it is really only when
early-receive is enabled (via ERT register) on these parts. Use packet
split with jumbos but only when early-receive is not enabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Thu, 17 Jun 2010 18:59:06 +0000 (18:59 +0000)]
e1000e: do not touch PHY page 800 registers when link speed is 1000Mbps
The PHY on 82577/82578 has issues when the registers on page 800 are
accessed when in gigabit mode. Do not clear the Wakeup Control register
when resetting the part since it is on page 800 (and will be cleared on
reset anyway).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Thu, 17 Jun 2010 18:58:43 +0000 (18:58 +0000)]
e1000e: avoid polling h/w registers during link negotiation
Avoid touching hardware registers when possible, otherwise link negotiation
can get messed up when user-level scripts are rapidly polling the driver to
see if/when link is up. Use the saved link state information instead when
possible.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Wed, 23 Jun 2010 18:57:09 +0000 (11:57 -0700)]
cnic: Disable statistics initialization for eth clients that do not support statistics
Disable statistics initialization for eth clients that do not support
statistics. This prevents memory corruption on bnx2x hw.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Anirban Chakraborty [Wed, 23 Jun 2010 18:49:42 +0000 (11:49 -0700)]
net: add dependency on fw class module to qlcnic and netxen_nic
netxen_nic and qlcnic driver depends on firmware_class module.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 23 Jun 2010 00:32:03 +0000 (00:32 +0000)]
snmp: fix SNMP_ADD_STATS()
commit
aa2ea0586d9d (tcp: fix outsegs stat for TSO segments) incorrectly
assumed SNMP_ADD_STATS() was used from BH context.
Fix this using mib[!in_softirq()] instead of mib[0]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Jun 2010 17:54:12 +0000 (10:54 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Filip Aben [Tue, 22 Jun 2010 17:10:35 +0000 (10:10 -0700)]
hso: remove setting of low_latency flag
This patch removes the setting of the low_latency flag.
tty_flip_buffer_push() is occasionally being called in irq context, which
causes a hang if the low_latency flag is set.
Removing the low_latency flag only seems to impact the flush to ldisc,
which will now be put on a workqueue.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 15 Jun 2010 01:52:25 +0000 (01:52 +0000)]
udp: Fix bogus UFO packet generation
It has been reported that the new UFO software fallback path
fails under certain conditions with NFS. I tracked the problem
down to the generation of UFO packets that are smaller than the
MTU. The software fallback path simply discards these packets.
This patch fixes the problem by not generating such packets on
the UFO path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helge Deller [Mon, 21 Jun 2010 20:50:18 +0000 (13:50 -0700)]
lasi82596: fix netdev_mc_count conversion
Fix commit
4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when
appropriate)
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Mon, 21 Jun 2010 03:44:50 +0000 (03:44 +0000)]
NET: MIPSsim: Fix modpost warning.
$ make CONFIG_DEBUG_SECTION_MISMATCH=y
[...]
WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe()
The variable mipsnet_driver references
the function __init mipsnet_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
[...]
Fixed by making mipsnet_probe __devinit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/mipsnet.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Sjur Braendeland [Thu, 17 Jun 2010 06:55:41 +0000 (06:55 +0000)]
caif: Add debug connection type for CAIF.
Added new CAIF protocol type CAIFPROTO_DEBUG for accessing
CAIF debug on the ST Ericsson modems.
There are two debug servers on the modem, one for radio related
debug (CAIF_RADIO_DEBUG_SERVICE) and the other for
communication/application related debug (CAIF_COM_DEBUG_SERVICE).
The debug connection can contain trace debug printouts or
interactive debug used for debugging and test.
Debug connections can be of type STREAM or SEQPACKET.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sjur Braendeland [Thu, 17 Jun 2010 06:55:40 +0000 (06:55 +0000)]
caif: Use link layer MTU instead of fixed MTU
Previously CAIF supported maximum transfer size of ~4050.
The transfer size is now calculated dynamically based on the
link layers mtu size.
Signed-off-by: Sjur Braendeland@stericsson.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Sjur Braendeland [Thu, 17 Jun 2010 06:55:39 +0000 (06:55 +0000)]
caif: Bugfix - RFM must support segmentation.
CAIF Remote File Manager may send or receive more than 4050 bytes.
Due to this The CAIF RFM service have to support segmentation.
Signed-off-by: Sjur Braendeland@stericsson.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Sjur Braendeland [Thu, 17 Jun 2010 06:55:38 +0000 (06:55 +0000)]
caif: Bugfix not all services uses flow-ctrl.
Flow control is not used by all CAIF services.
The usage of flow control is now part of the gerneal
initialization function for CAIF Services.
Signed-off-by: Sjur Braendeland@stericsson.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 16 Jun 2010 13:28:34 +0000 (13:28 +0000)]
e1000e: update driver version number
Also separate out an _EXTRAVERSION similar to the core kernel.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 16 Jun 2010 13:28:11 +0000 (13:28 +0000)]
e1000e: update copyright information
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 16 Jun 2010 13:27:49 +0000 (13:27 +0000)]
e1000e: enable support for EEE on 82579
This patch enables IEEE802.3az (a.k.a. Energy Efficient Ethernet) on the
new 82579 LOMs. An optional module parameter is provided to disable the
feature if desired.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 16 Jun 2010 13:27:28 +0000 (13:27 +0000)]
e1000e: initial support for 82579 LOMs
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 16 Jun 2010 13:27:05 +0000 (13:27 +0000)]
e1000e: fix check for manageability on ICHx/PCH
Do not check for all the bits in E1000_FWSM_MODE_MASK when checking for
manageability on 82577/82578; only check if iAMT is enabled. Both of the
manageability checks (for 82577/82578 and ICHx) must check the firmware
valid bit too since the other bits are only valid when the latter is set.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 16 Jun 2010 13:26:41 +0000 (13:26 +0000)]
e1000e: separate out PHY statistics register updates
The 82577/82578 parts have half-duplex statistics in PHY registers. These
need only be read when in half-duplex and should all be read at once rather
than one at a time to prevent excessive cycles of acquiring/releasing the
PHY semaphore.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 16 Jun 2010 13:26:17 +0000 (13:26 +0000)]
e1000e: cleanup e1000_sw_lcd_config_ich8lan()
Do not acquire and release the PHY unnecessarily for parts that return
from this workaround without actually accessing the PHY registers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 16 Jun 2010 13:25:55 +0000 (13:25 +0000)]
e1000e: cleanup ethtool loopback setup code
Refactor the loopback setup code to first handle the only 10/100 PHY
supported by the driver if applicable and then handle the 1Gig PHYs in a
switch statement for PHY-specific setups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dimitris Michailidis [Fri, 18 Jun 2010 10:05:35 +0000 (10:05 +0000)]
cxgb4: minor cleanup
Remove an unused flag and replace couple constants with enums.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dimitris Michailidis [Fri, 18 Jun 2010 10:05:34 +0000 (10:05 +0000)]
cxgb4: update FW definitions
Update to latest FW API. Most changes here pertain to port types and
querying FW for parameter values.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dimitris Michailidis [Fri, 18 Jun 2010 10:05:33 +0000 (10:05 +0000)]
cxgb4: add a missing error interrupt
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dimitris Michailidis [Fri, 18 Jun 2010 10:05:32 +0000 (10:05 +0000)]
cxgb4: propagate link initialization errors to .ndo_open's callers
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dimitris Michailidis [Fri, 18 Jun 2010 10:05:31 +0000 (10:05 +0000)]
cxgb4: switch to 64 bit inteface statistics
Implement ndo_get_stats64, remove ndo_get_stats.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dimitris Michailidis [Fri, 18 Jun 2010 10:05:30 +0000 (10:05 +0000)]
cxgb4: set dev_id to the port number
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>