x86/mm/32: Enable full randomization on i386 and X86_32

commit 8b8addf891de8a00e4d39fc32f93f7c5eb8feceb upstream.

Currently on i386 and on X86_64 when emulating X86_32 in legacy mode, only
the stack and the executable are randomized but not other mmapped files
(libraries, vDSO, etc.). This patch enables randomization for the
libraries, vDSO and mmap requests on i386 and in X86_32 in legacy mode.

By default on i386 there are 8 bits for the randomization of the libraries,
vDSO and mmaps which only uses 1MB of VA.

This patch preserves the original randomness, using 1MB of VA out of 3GB or
4GB. We think that 1MB out of 3GB is not a big cost for having the ASLR.

The first obvious security benefit is that all objects are randomized (not
only the stack and the executable) in legacy mode which highly increases
the ASLR effectiveness, otherwise the attackers may use these
non-randomized areas. But also sensitive setuid/setgid applications are
more secure because currently, attackers can disable the randomization of
these applications by setting the ulimit stack to "unlimited". This is a
very old and widely known trick to disable the ASLR in i386 which has been
allowed for too long.

Another trick used to disable the ASLR was to set the ADDR_NO_RANDOMIZE
personality flag, but fortunately this doesn't work on setuid/setgid
applications because there is security checks which clear Security-relevant
flags.

This patch always randomizes the mmap_legacy_base address, removing the
possibility to disable the ASLR by setting the stack to "unlimited".

Signed-off-by: Hector Marco-Gisbert <hecmargi@upv.es>
Acked-by: Ismael Ripoll Ripoll <iripoll@upv.es>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/1457639460-5242-1-git-send-email-hecmargi@upv.es
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: sony: do not bail out when the sixaxis refuses the output report

commit 19f4c2ba869517048add62c202f9645b6adf5dfb upstream.

When setting the operational mode, some third party (Speedlink Strike-FX)
gamepads refuse the output report. Failing here means we refuse to
initialize the gamepad while this should be harmless.

The weird part is that the initial commit that added this: a7de9b8
("HID: sony: Enable Gasia third-party PS3 controllers") mentions this
very same controller as one requiring this output report.
Anyway, it's broken for one user at least, so let's change it.
We will report an error, but at least the controller should work.

And no, these devices present themselves as legacy Sony controllers
(VID:PID of 054C:0268, as in the official ones) so there are no ways
of discriminating them from the official ones.

https://bugzilla.redhat.com/show_bug.cgi?id=1255325

Reported-and-tested-by: Max Fedotov <thesourcehim@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PNP: Add Broadwell to Intel MCH size workaround

commit a77060f07ffc6ac978e280e738302f3e5572a99e upstream.

Add device ID 0x1604 for Broadwell to commit cb171f7abb9a ("PNP:
Work around BIOS defects in Intel MCH area reporting").

>From a Lenovo ThinkPad T550:

  system 00:01: [io  0x1800-0x189f] could not be reserved
  system 00:01: [io  0x0800-0x087f] has been reserved
  system 00:01: [io  0x0880-0x08ff] has been reserved
  system 00:01: [io  0x0900-0x097f] has been reserved
  system 00:01: [io  0x0980-0x09ff] has been reserved
  system 00:01: [io  0x0a00-0x0a7f] has been reserved
  system 00:01: [io  0x0a80-0x0aff] has been reserved
  system 00:01: [io  0x0b00-0x0b7f] has been reserved
  system 00:01: [io  0x0b80-0x0bff] has been reserved
  system 00:01: [io  0x15e0-0x15ef] has been reserved
  system 00:01: [io  0x1600-0x167f] has been reserved
  system 00:01: [io  0x1640-0x165f] has been reserved
  system 00:01: [mem 0xf8000000-0xfbffffff] could not be reserved
  system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
  system 00:01: [mem 0xfed10000-0xfed13fff] has been reserved
  system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
  system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
  system 00:01: [mem 0xfed45000-0xfed4bfff] has been reserved
  system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
  [...]
  resource sanity check: requesting [mem 0xfed10000-0xfed15fff], which spans more than pnp 00:01 [mem 0xfed10000-0xfed13fff]
  ------------[ cut here ]------------
  WARNING: CPU: 2 PID: 1 at /build/linux-CrHvZ_/linux-4.2.6/arch/x86/mm/ioremap.c:198 __ioremap_caller+0x2ee/0x360()
  Info: mapping multiple BARs. Your kernel is fine.
  Modules linked in:
  CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.2.0-1-amd64 #1 Debian 4.2.6-1
  Hardware name: LENOVO 20CKCTO1WW/20CKCTO1WW, BIOS N11ET34W (1.10 ) 08/20/2015
   0000000000000000 ffffffff817e6868 ffffffff8154e2f6 ffff8802241efbf8
   ffffffff8106e5b1 ffffc90000e98000 0000000000006000 ffffc90000e98000
   0000000000006000 0000000000000000 ffffffff8106e62a ffffffff817e68c8
  Call Trace:
   [<ffffffff8154e2f6>] ? dump_stack+0x40/0x50
   [<ffffffff8106e5b1>] ? warn_slowpath_common+0x81/0xb0
   [<ffffffff8106e62a>] ? warn_slowpath_fmt+0x4a/0x50
   [<ffffffff810742a3>] ? iomem_map_sanity_check+0xb3/0xc0
   [<ffffffff8105dade>] ? __ioremap_caller+0x2ee/0x360
   [<ffffffff81036ae6>] ? snb_uncore_imc_init_box+0x66/0x90
   [<ffffffff810351a8>] ? uncore_pci_probe+0xc8/0x1a0
   [<ffffffff81302d7f>] ? local_pci_probe+0x3f/0xa0
   [<ffffffff81303ea4>] ? pci_device_probe+0xc4/0x110
   [<ffffffff813d9b1e>] ? driver_probe_device+0x1ee/0x450
   [<ffffffff813d9dfb>] ? __driver_attach+0x7b/0x80
   [<ffffffff813d9d80>] ? driver_probe_device+0x450/0x450
   [<ffffffff813d796a>] ? bus_for_each_dev+0x5a/0x90
   [<ffffffff813d9091>] ? bus_add_driver+0x1f1/0x290
   [<ffffffff81b37fa8>] ? uncore_cpu_setup+0xc/0xc
   [<ffffffff813da73f>] ? driver_register+0x5f/0xe0
   [<ffffffff81b38074>] ? intel_uncore_init+0xcc/0x2b0
   [<ffffffff81b37fa8>] ? uncore_cpu_setup+0xc/0xc
   [<ffffffff8100213e>] ? do_one_initcall+0xce/0x200
   [<ffffffff8108a100>] ? parse_args+0x140/0x4e0
   [<ffffffff81b2b0cb>] ? kernel_init_freeable+0x162/0x1e8
   [<ffffffff815443f0>] ? rest_init+0x80/0x80
   [<ffffffff815443fe>] ? kernel_init+0xe/0xf0
   [<ffffffff81553e5f>] ? ret_from_fork+0x3f/0x70
   [<ffffffff815443f0>] ? rest_init+0x80/0x80
  ---[ end trace 472e7959536abf12 ]---

  00:00.0 Host bridge: Intel Corporation Broadwell-U Host Bridge -OPI (rev 09)
          Subsystem: Lenovo Device 2223
          Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
          Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
          Latency: 0
          Capabilities: [e0] Vendor Specific Information: Len=0c <?>
          Kernel driver in use: bdw_uncore
  00: 86 80 04 16 06 00 90 20 09 00 00 06 00 00 00 00
  10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  20: 00 00 00 00 00 00 00 00 00 00 00 00 aa 17 23 22
  30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

Signed-off-by: Christophe Le Roy <christophe.fish@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PNP: Add Haswell-ULT to Intel MCH size workaround

commit ed1f0eeebaeeb7f790e9e7642116a208581e5bfc upstream.

Add device ID 0x0a04 for Haswell-ULT to the list of devices with MCH
problems.

From a Lenovo ThinkPad T440S:
[    0.188604] pnp: PnP ACPI init
[    0.189044] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.189048] system 00:00: [mem 0x000c0000-0x000c3fff] could not be reserved
[    0.189050] system 00:00: [mem 0x000c4000-0x000c7fff] could not be reserved
[    0.189052] system 00:00: [mem 0x000c8000-0x000cbfff] could not be reserved
[    0.189054] system 00:00: [mem 0x000cc000-0x000cffff] could not be reserved
[    0.189056] system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
[    0.189058] system 00:00: [mem 0x000d4000-0x000d7fff] has been reserved
[    0.189060] system 00:00: [mem 0x000d8000-0x000dbfff] has been reserved
[    0.189061] system 00:00: [mem 0x000dc000-0x000dffff] has been reserved
[    0.189063] system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved
[    0.189065] system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved
[    0.189067] system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved
[    0.189069] system 00:00: [mem 0x000ec000-0x000effff] could not be reserved
[    0.189071] system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
[    0.189073] system 00:00: [mem 0x00100000-0xdf9fffff] could not be reserved
[    0.189075] system 00:00: [mem 0xfec00000-0xfed3ffff] could not be reserved
[    0.189078] system 00:00: [mem 0xfed4c000-0xffffffff] could not be reserved
[    0.189082] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.189216] system 00:01: [io  0x1800-0x189f] could not be reserved
[    0.189220] system 00:01: [io  0x0800-0x087f] has been reserved
[    0.189222] system 00:01: [io  0x0880-0x08ff] has been reserved
[    0.189224] system 00:01: [io  0x0900-0x097f] has been reserved
[    0.189226] system 00:01: [io  0x0980-0x09ff] has been reserved
[    0.189229] system 00:01: [io  0x0a00-0x0a7f] has been reserved
[    0.189231] system 00:01: [io  0x0a80-0x0aff] has been reserved
[    0.189233] system 00:01: [io  0x0b00-0x0b7f] has been reserved
[    0.189235] system 00:01: [io  0x0b80-0x0bff] has been reserved
[    0.189238] system 00:01: [io  0x15e0-0x15ef] has been reserved
[    0.189240] system 00:01: [io  0x1600-0x167f] has been reserved
[    0.189242] system 00:01: [io  0x1640-0x165f] has been reserved
[    0.189246] system 00:01: [mem 0xf8000000-0xfbffffff] could not be reserved
[    0.189249] system 00:01: [mem 0x00000000-0x00000fff] could not be reserved
[    0.189251] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.189254] system 00:01: [mem 0xfed10000-0xfed13fff] has been reserved
[    0.189256] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.189258] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.189261] system 00:01: [mem 0xfed45000-0xfed4bfff] has been reserved
[    0.189264] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[....]
[    0.583653] resource sanity check: requesting [mem 0xfed10000-0xfed15fff], which spans more than pnp 00:01 [mem 0xfed10000-0xfed13fff]
[    0.583654] ------------[ cut here ]------------
[    0.583660] WARNING: CPU: 0 PID: 1 at arch/x86/mm/ioremap.c:198 __ioremap_caller+0x2c5/0x380()
[    0.583661] Info: mapping multiple BARs. Your kernel is fine.
[    0.583662] Modules linked in:

[    0.583666] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.3.3-303.fc23.x86_64 #1
[    0.583668] Hardware name: LENOVO 20AR001GXS/20AR001GXS, BIOS GJET86WW (2.36 ) 12/04/2015
[    0.583670]  0000000000000000 0000000014cf7e59 ffff880214a1baf8 ffffffff813a625f
[    0.583673]  ffff880214a1bb40 ffff880214a1bb30 ffffffff810a07c2 00000000fed10000
[    0.583675]  ffffc90000cb8000 0000000000006000 0000000000000000 ffff8800d6381040
[    0.583678] Call Trace:
[    0.583683]  [<ffffffff813a625f>] dump_stack+0x44/0x55
[    0.583686]  [<ffffffff810a07c2>] warn_slowpath_common+0x82/0xc0
[    0.583688]  [<ffffffff810a085c>] warn_slowpath_fmt+0x5c/0x80
[    0.583692]  [<ffffffff810a6fba>] ? iomem_map_sanity_check+0xba/0xd0
[    0.583695]  [<ffffffff81065835>] __ioremap_caller+0x2c5/0x380
[    0.583698]  [<ffffffff81065907>] ioremap_nocache+0x17/0x20
[    0.583701]  [<ffffffff8103a119>] snb_uncore_imc_init_box+0x79/0xb0
[    0.583705]  [<ffffffff81038900>] uncore_pci_probe+0xd0/0x1b0
[    0.583707]  [<ffffffff813efda5>] local_pci_probe+0x45/0xa0
[    0.583710]  [<ffffffff813f118d>] pci_device_probe+0xfd/0x140
[    0.583713]  [<ffffffff814d9b52>] driver_probe_device+0x222/0x480
[    0.583715]  [<ffffffff814d9e34>] __driver_attach+0x84/0x90
[    0.583717]  [<ffffffff814d9db0>] ? driver_probe_device+0x480/0x480
[    0.583720]  [<ffffffff814d762c>] bus_for_each_dev+0x6c/0xc0
[    0.583722]  [<ffffffff814d930e>] driver_attach+0x1e/0x20
[    0.583724]  [<ffffffff814d8e4b>] bus_add_driver+0x1eb/0x280
[    0.583727]  [<ffffffff81d6af1a>] ? uncore_cpu_setup+0x12/0x12
[    0.583729]  [<ffffffff814da680>] driver_register+0x60/0xe0
[    0.583733]  [<ffffffff813ef78c>] __pci_register_driver+0x4c/0x50
[    0.583736]  [<ffffffff81d6affc>] intel_uncore_init+0xe2/0x2e6
[    0.583738]  [<ffffffff81d6af1a>] ? uncore_cpu_setup+0x12/0x12
[    0.583741]  [<ffffffff81002123>] do_one_initcall+0xb3/0x200
[    0.583745]  [<ffffffff810be500>] ? parse_args+0x1a0/0x4a0
[    0.583749]  [<ffffffff81d5c1c8>] kernel_init_freeable+0x189/0x223
[    0.583752]  [<ffffffff81775c40>] ? rest_init+0x80/0x80
[    0.583754]  [<ffffffff81775c4e>] kernel_init+0xe/0xe0
[    0.583758]  [<ffffffff81781adf>] ret_from_fork+0x3f/0x70
[    0.583760]  [<ffffffff81775c40>] ? rest_init+0x80/0x80
[    0.583765] ---[ end trace 077c426a39e018aa ]---

00:00.0 Host bridge [0600]: Intel Corporation Haswell-ULT DRAM Controller [8086:0a04] (rev 0b)
Subsystem: Lenovo Device [17aa:220c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: hsw_uncore

Link: https://bugzilla.redhat.com/show_bug.cgi?id=1300955
Tested-by: <robo@tcp.sk>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ignore errors from scsi_dh_add_device()

commit 221255aee67ec1c752001080aafec0c4e9390d95 upstream.

device handler initialisation might fail due to a number of
reasons. But as device_handlers are optional this shouldn't
cause us to disable the device entirely.
So just ignore errors from scsi_dh_add_device().

Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipath: Restrict use of the write() interface

Commit e6bd18f57aad ("IB/security: Restrict use of the write()
interface") fixed a security problem with various write()
implementations in the Infiniband subsystem.  In older kernel versions
the ipath_write() function has the same problem and needs the same
restriction.  (The ipath driver has been completely removed upstream.)

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: consider recv buf for the initial window scale

[ Upstream commit f626300a3e776ccc9671b0dd94698fb3aa315966 ]

tcp_select_initial_window() intends to advertise a window
scaling for the maximum possible window size. To do so,
it considers the maximum of net.ipv4.tcp_rmem[2] and
net.core.rmem_max as the only possible upper-bounds.
However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE
to set the socket's receive buffer size to values
larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max.
Thus, SO_RCVBUFFORCE is effectively ignored by
tcp_select_initial_window().

To fix this, consider the maximum of net.ipv4.tcp_rmem[2],
net.core.rmem_max and socket's initial buffer space.

Fixes: b0573dea1fb3 ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Suggested-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qed: Fix setting/clearing bit in completion bitmap

[ Upstream commit 59d3f1ceb69b54569685d0c34dff16a1e0816b19 ]

Slowpath completion handling is incorrectly changing
SPQ_RING_SIZE bits instead of a single one.

Fixes: 76a9a3642a0b ("qed: fix handling of concurrent ramrods")
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/irda: fix NULL pointer dereference on memory allocation failure

[ Upstream commit d3e6952cfb7ba5f4bfa29d4803ba91f96ce1204d ]

I ran into this:

    kasan: CONFIG_KASAN_INLINE enabled
    kasan: GPF could be caused by NULL-ptr deref or user memory access
    general protection fault: 0000 [#1] PREEMPT SMP KASAN
    CPU: 2 PID: 2012 Comm: trinity-c3 Not tainted 4.7.0-rc7+ #19
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
    task: ffff8800b745f2c0 ti: ffff880111740000 task.ti: ffff880111740000
    RIP: 0010:[<ffffffff82bbf066>]  [<ffffffff82bbf066>] irttp_connect_request+0x36/0x710
    RSP: 0018:ffff880111747bb8  EFLAGS: 00010286
    RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000069dd8358
    RDX: 0000000000000009 RSI: 0000000000000027 RDI: 0000000000000048
    RBP: ffff880111747c00 R08: 0000000000000000 R09: 0000000000000000
    R10: 0000000069dd8358 R11: 1ffffffff0759723 R12: 0000000000000000
    R13: ffff88011a7e4780 R14: 0000000000000027 R15: 0000000000000000
    FS:  00007fc738404700(0000) GS:ffff88011af00000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 00007fc737fdfb10 CR3: 0000000118087000 CR4: 00000000000006e0
    Stack:
     0000000000000200 ffff880111747bd8 ffffffff810ee611 ffff880119f1f220
     ffff880119f1f4f8 ffff880119f1f4f0 ffff88011a7e4780 ffff880119f1f232
     ffff880119f1f220 ffff880111747d58 ffffffff82bca542 0000000000000000
    Call Trace:
     [<ffffffff82bca542>] irda_connect+0x562/0x1190
     [<ffffffff825ae582>] SYSC_connect+0x202/0x2a0
     [<ffffffff825b4489>] SyS_connect+0x9/0x10
     [<ffffffff8100334c>] do_syscall_64+0x19c/0x410
     [<ffffffff83295ca5>] entry_SYSCALL64_slow_path+0x25/0x25
    Code: 41 89 ca 48 89 e5 41 57 41 56 41 55 41 54 41 89 d7 53 48 89 fb 48 83 c7 48 48 89 fa 41 89 f6 48 c1 ea 03 48 83 ec 20 4c 8b 65 10 <0f> b6 04 02 84 c0 74 08 84 c0 0f 8e 4c 04 00 00 80 7b 48 00 74
    RIP  [<ffffffff82bbf066>] irttp_connect_request+0x36/0x710
     RSP <ffff880111747bb8>
    ---[ end trace 4cda2588bc055b30 ]---

The problem is that irda_open_tsap() can fail and leave self->tsap = NULL,
and then irttp_connect_request() almost immediately dereferences it.

Cc: stable@vger.kernel.org
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: bgmac: Fix infinite loop in bgmac_dma_tx_add()

[ Upstream commit e86663c475d384ab5f46cb5637e9b7ad08c5c505 ]

Nothing is decrementing the index "i" while we are cleaning up the
fragments we could not successful transmit.

Fixes: 9cde94506eacf ("bgmac: implement scatter/gather support")
Reported-by: coverity (CID 1352048)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bonding: set carrier off for devices created through netlink

[ Upstream commit 005db31d5f5f7c31cfdc43505d77eb3ca5cf8ec6 ]

Commit e826eafa65c6 ("bonding: Call netif_carrier_off after
register_netdevice") moved netif_carrier_off() from bond_init() to
bond_create(), but the latter is called only for initial default
devices and ones created through sysfs:

 $ modprobe bonding
 $ echo +bond1 > /sys/class/net/bonding_masters
 $ ip link add bond2 type bond
 $ grep "MII Status" /proc/net/bonding/*
 /proc/net/bonding/bond0:MII Status: down
 /proc/net/bonding/bond1:MII Status: down
 /proc/net/bonding/bond2:MII Status: up

Ensure that carrier is initially off also for devices created through
netlink.

Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: reject RTNH_F_DEAD and RTNH_F_LINKDOWN from user space

[ Upstream commit 80610229ef7b26615dbb6cb6e873709a60bacc9f ]

Vegard Nossum is reporting for a crash in fib_dump_info
when nh_dev = NULL and fib_nhs == 1:

Pid: 50, comm: netlink.exe Not tainted 4.7.0-rc5+
RIP: 0033:[<00000000602b3d18>]
RSP: 0000000062623890  EFLAGS: 00010202
RAX: 0000000000000000 RBX: 000000006261b800 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000024 RDI: 000000006245ba00
RBP: 00000000626238f0 R08: 000000000000029c R09: 0000000000000000
R10: 0000000062468038 R11: 000000006245ba00 R12: 000000006245ba00
R13: 00000000625f96c0 R14: 00000000601e16f0 R15: 0000000000000000
Kernel panic - not syncing: Kernel mode fault at addr 0x2e0, ip 0x602b3d18
CPU: 0 PID: 50 Comm: netlink.exe Not tainted 4.7.0-rc5+ #581
Stack:
 626238f0 960226a02 00000400 000000fe
 62623910 600afca7 62623970 62623a48
 62468038 00000018 00000000 00000000
Call Trace:
 [<602b3e93>] rtmsg_fib+0xd3/0x190
 [<602b6680>] fib_table_insert+0x260/0x500
 [<602b0e5d>] inet_rtm_newroute+0x4d/0x60
 [<60250def>] rtnetlink_rcv_msg+0x8f/0x270
 [<60267079>] netlink_rcv_skb+0xc9/0xe0
 [<60250d4b>] rtnetlink_rcv+0x3b/0x50
 [<60265400>] netlink_unicast+0x1a0/0x2c0
 [<60265e47>] netlink_sendmsg+0x3f7/0x470
 [<6021dc9a>] sock_sendmsg+0x3a/0x90
 [<6021e0d0>] ___sys_sendmsg+0x300/0x360
 [<6021fa64>] __sys_sendmsg+0x54/0xa0
 [<6021fac0>] SyS_sendmsg+0x10/0x20
 [<6001ea68>] handle_syscall+0x88/0x90
 [<600295fd>] userspace+0x3fd/0x500
 [<6001ac55>] fork_handler+0x85/0x90

$ addr2line -e vmlinux -i 0x602b3d18
include/linux/inetdevice.h:222
net/ipv4/fib_semantics.c:1264

Problem happens when RTNH_F_LINKDOWN is provided from user space
when creating routes that do not use the flag, catched with
netlink fuzzer.

Currently, the kernel allows user space to set both flags
to nh_flags and fib_flags but this is not intentional, the
assumption was that they are not set. Fix this by rejecting
both flags with EINVAL.

Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Fixes: 0eeb075fad73 ("net: ipv4 sysctl option to ignore routes when nexthop link is down")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Dinesh Dutt <ddutt@cumulusnetworks.com>
Cc: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: enable per-socket rate limiting of all 'challenge acks'

[ Upstream commit 083ae308280d13d187512b9babe3454342a7987e ]

The per-socket rate limit for 'challenge acks' was introduced in the
context of limiting ack loops:

commit f2b2c582e824 ("tcp: mitigate ACK loops for connections as tcp_sock")

And I think it can be extended to rate limit all 'challenge acks' on a
per-socket basis.

Since we have the global tcp_challenge_ack_limit, this patch allows for
tcp_challenge_ack_limit to be set to a large value and effectively rely on
the per-socket limit, or set tcp_challenge_ack_limit to a lower value and
still prevents a single connections from consuming the entire challenge ack
quota.

It further moves in the direction of eliminating the global limit at some
point, as Eric Dumazet has suggested. This a follow-up to:
Subject: tcp: make challenge acks less predictable

Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Yue Cao <ycao009@ucr.edu>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: make challenge acks less predictable

[ Upstream commit 75ff39ccc1bd5d3c455b6822ab09e533c551f758 ]

Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.

This patch increases the default limit from 100 to 1000, and adds
some randomization so that the attacker can no longer hijack
sessions without spending a considerable amount of probes.

Based on initial analysis and patch from Linus.

Note that we also have per socket rate limiting, so it is tempting
to remove the host limit in the future.

v2: randomize the count of challenge acks per second, not the period.

Fixes: 282f23c6ee34 ("tcp: implement RFC 5961 3.2")
Reported-by: Yue Cao <ycao009@ucr.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.17

vfs: fix deadlock in file_remove_privs() on overlayfs

commit c1892c37769cf89c7e7ba57528ae2ccb5d153c9b upstream.

file_remove_privs() is called with inode lock on file_inode(), which
proceeds to calling notify_change() on file->f_path.dentry.  Which triggers
the WARN_ON_ONCE(!inode_is_locked(inode)) in addition to deadlocking later
when ovl_setattr tries to lock the underlying inode again.

Fix this mess by not mixing the layers, but doing everything on underlying
dentry/inode.

Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 07a2daab49c5 ("ovl: Copy up underlying inode's ->i_mode to overlay inode")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

intel_th: Fix a deadlock in modprobing

commit a36aa80f3cb2540fb1dbad6240852de4365a2e82 upstream.

Driver initialization tries to request a hub (GTH) driver module from
its probe callback, resulting in a deadlock.

This patch solves the problem by adding a deferred work for requesting
the hub module.

Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

intel_th: pci: Add Kaby Lake PCH-H support

commit 7a1a47ce35821b40f5b2ce46379ba14393bc3873 upstream.

This adds Intel(R) Trace Hub PCI ID for Kaby Lake PCH-H.

Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mvneta: set real interrupt per packet for tx_done

commit 06708f81528725148473c0869d6af5f809c6824b upstream.

Commit aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.

In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.

This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.

Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libceph: apply new_state before new_up_client on incrementals

commit 930c532869774ebf8af9efe9484c597f896a7d46 upstream.

Currently, osd_weight and osd_state fields are updated in the encoding
order.  This is wrong, because an incremental map may look like e.g.

    new_up_client: { osd=6, addr=... } # set osd_state and addr
    new_state: { osd=6, xorstate=EXISTS } # clear osd_state

Suppose osd6's current osd_state is EXISTS (i.e. osd6 is down).  After
applying new_up_client, osd_state is changed to EXISTS | UP.  Carrying
on with the new_state update, we flip EXISTS and leave osd6 in a weird
"!EXISTS but UP" state.  A non-existent OSD is considered down by the
mapping code

2087    for (i = 0; i < pg->pg_temp.len; i++) {
2088            if (ceph_osd_is_down(osdmap, pg->pg_temp.osds[i])) {
2089                    if (ceph_can_shift_osds(pi))
2090                            continue;
2091
2092                    temp->osds[temp->size++] = CRUSH_ITEM_NONE;

and so requests get directed to the second OSD in the set instead of
the first, resulting in OSD-side errors like:

[WRN] : client.4239 192.168.122.21:0/2444980242 misdirected client.4239.1:2827 pg 2.5df899f2 to osd.4 not [1,4,6] in e680/680

and hung rbds on the client:

[  493.566367] rbd: rbd0: write 400000 at 11cc00000 (0)
[  493.566805] rbd: rbd0:   result -6 xferred 400000
[  493.567011] blk_update_request: I/O error, dev rbd0, sector 9330688

The fix is to decouple application from the decoding and:
- apply new_weight first
- apply new_state before new_up_client
- twiddle osd_state flags if marking in
- clear out some of the state if osd is destroyed

Fixes: http://tracker.ceph.com/issues/14901

Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libata: LITE-ON CX1-JB256-HP needs lower max_sectors

commit 1488a1e3828d60d74c9b802a05e24c0487babe4e upstream.

Since 34b48db66e08 ("block: remove artifical max_hw_sectors cap"),
max_sectors is no longer limited to BLK_DEF_MAX_SECTORS and LITE-ON
CX1-JB256-HP keeps timing out with higher max_sectors.  Revert it to
the previous value.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: dgerasimov@gmail.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=121671
Fixes: 34b48db66e08 ("block: remove artifical max_hw_sectors cap")
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: mux: reg: wrong condition checked for of_address_to_resource return value

commit 22ebf00eb56fe77922de8138aa9af9996582c2b3 upstream.

of_address_to_resource return 0 on successful call but
devm_ioremap_resource is called only if it returns non-zero value

Signed-off-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

posix_cpu_timer: Exit early when process has been reaped

commit 2c13ce8f6b2f6fd9ba2f9261b1939fc0f62d1307 upstream.

Variable "now" seems to be genuinely used unintialized
if branch

if (CPUCLOCK_PERTHREAD(timer->it_clock)) {

is not taken and branch

if (unlikely(sighand == NULL)) {

is taken. In this case the process has been reaped and the timer is marked as
disarmed anyway. So none of the postprocessing of the sample is
required. Return right away.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Link: http://lkml.kernel.org/r/20160707223911.GA26483@p183.telecom.by
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: fix airspy usb probe error path

commit aa93d1fee85c890a34f2510a310e55ee76a27848 upstream.

Fix a memory leak on probe error of the airspy usb device driver.

The problem is triggered when more than 64 usb devices register with
v4l2 of type VFL_TYPE_SDR or VFL_TYPE_SUBDEV.

The memory leak is caused by the probe function of the airspy driver
mishandeling errors and not freeing the corresponding control structures
when an error occours registering the device to v4l2 core.

A badusb device can emulate 64 of these devices, and then through
continual emulated connect/disconnect of the 65th device, cause the
kernel to run out of RAM and crash the kernel, thus causing a local DOS
vulnerability.

Fixes CVE-2016-5400

Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipr: Clear interrupt on croc/crocodile when running with LSI

commit 54e430bbd490e18ab116afa4cd90dcc45787b3df upstream.

If we fall back to using LSI on the Croc or Crocodile chip we need to
clear the interrupt so we don't hang the system.

Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SCSI: fix new bug in scsi_dev_info_list string matching

commit 5e7ff2ca7f2da55fe777167849d0c93403bd0dc8 upstream.

Commit b704f70ce200 ("SCSI: fix bug in scsi_dev_info_list matching")
changed the way vendor- and model-string matching was carried out in the
routine that looks up entries in a SCSI devinfo list.  The new matching
code failed to take into account the case of a maximum-length string; in
such cases it could end up testing for a terminating '\0' byte beyond
the end of the memory allocated to the string.  This out-of-bounds bug
was detected by UBSAN.

I don't know if anybody has actually encountered this bug.  The symptom
would be that a device entry in the blacklist might not be matched
properly if it contained an 8-character vendor name or a 16-character
model name.  Such entries certainly exist in scsi_static_device_list.

This patch fixes the problem by adding a check for a maximum-length
string before the '\0' test.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: b704f70ce200 ("SCSI: fix bug in scsi_dev_info_list matching")
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDS: fix rds_tcp_init() error path

commit 3dad5424adfb346c871847d467f97dcdca64ea97 upstream.

If register_pernet_subsys() fails, we shouldn't try to call
unregister_pernet_subsys().

Fixes: 467fa15356 ("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.")
Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: fix oops caused by wrong rtnl dellink usage

commit 25e1ed6e64f52a692ba3191c4fde650aab3ecc07 upstream.

For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...

This patch adds a private dellink function for the CAN device driver interface
that does just nothing.

It's a follow up to commit 993e6f2fd ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.

Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: fix handling of unmodifiable configuration options fix

commit bce271f255dae8335dc4d2ee2c4531e09cc67f5a upstream.

With upstream commit bb208f144cf3f59 (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.

When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.

Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: c_can: Update D_CAN TX and RX functions to 32 bit - fix Altera Cyclone access

commit 427460c83cdf55069eee49799a0caef7dde8df69 upstream.

When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.

The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.

Testing performed on Altera CycloneV (D_CAN).  Requesting tests on other
C_CAN & D_CAN platforms.

Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: at91_can: RX queue could get stuck at high bus load

commit 43200a4480cbbe660309621817f54cbb93907108 upstream.

At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Amr Bekhit <amrbekhit@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86: fix PEBS issues on Intel Atom/Core2

commit 1424a09a9e1839285e948d4ea9fdfca26c9a2086 upstream.

This patch fixes broken PEBS support on Intel Atom and Core2
due to wrong pointer arithmetic in intel_pmu_drain_pebs_core().

The get_next_pebs_record_by_bit() was called on PEBS format fmt0
which does not use the pebs_record_nhm layout.

Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Fixes: 21509084f999 ("perf/x86/intel: Handle multiple records in the PEBS buffer")
Link: http://lkml.kernel.org/r/1449182000-31524-3-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: handle ATTR_KILL*

commit b99c2d913810e56682a538c9f2394d76fca808f8 upstream.

Before 4bacc9c9234c ("overlayfs: Make f_path...") file->f_path pointed to
the underlying file, hence suid/sgid removal on write worked fine.

After that patch file->f_path pointed to the overlay file, and the file
mode bits weren't copied to overlay_inode->i_mode.  So the suid/sgid
removal simply stopped working.

The fix is to copy the mode bits, but then ovl_setattr() needs to clear
ATTR_MODE to avoid the BUG() in notify_change().  So do this first, then in
the next patch copy the mode.

Reported-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Cc: Eric Schultz <eric@startuperic.com>
Cc: Eric Hameleers <alien@slackware.com>
[backported by Eric Hameleers as seen in https://bugzilla.kernel.org/show_bug.cgi?id=150711]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/fair: Fix effective_load() to consistently use smoothed load

commit 7dd4912594daf769a46744848b05bd5bc6d62469 upstream.

Starting with the following commit:

  fde7d22e01aa ("sched/fair: Fix overly small weight for interactive group entities")

calc_tg_weight() doesn't compute the right value as expected by effective_load().

The difference is in the 'correction' term. In order to ensure \Sum
rw_j >= rw_i we cannot use tg->load_avg directly, since that might be
lagging a correction on the current cfs_rq->avg.load_avg value.
Therefore we use tg->load_avg - cfs_rq->tg_load_avg_contrib +
cfs_rq->avg.load_avg.

Now, per the referenced commit, calc_tg_weight() doesn't use
cfs_rq->avg.load_avg, as is later used in @w, but uses
cfs_rq->load.weight instead.

So stop using calc_tg_weight() and do it explicitly.

The effects of this bug are wake_affine() making randomly
poor choices in cgroup-intense workloads.

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: fde7d22e01aa ("sched/fair: Fix overly small weight for interactive group entities")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: block: fix packed command header endianness

commit f68381a70bb2b26c31b13fdaf67c778f92fd32b4 upstream.

The code that fills packed command header assumes that CPU runs in
little-endian mode. Hence the header is malformed in big-endian mode
and causes MMC data transfer errors:

[  563.200828] mmcblk0: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc40
[  563.219647] mmcblk0: packed cmd failed, nr 2, sectors 16, failure index: -1

Convert header data to LE.

Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Fixes: ce39f9d17c14 ("mmc: support packed write command for eMMC4.5 devices")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: fix use-after-free in sys_ioprio_get()

commit 8ba8682107ee2ca3347354e018865d8e1967c5f4 upstream.

get_task_ioprio() accesses the task->io_context without holding the task
lock and thus can race with exit_io_context(), leading to a
use-after-free. The reproducer below hits this within a few seconds on
my 4-core QEMU VM:

#define _GNU_SOURCE
#include <assert.h>
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/wait.h>

int main(int argc, char **argv)
{
pid_t pid, child;
long nproc, i;

/* ioprio_set(IOPRIO_WHO_PROCESS, 0, IOPRIO_PRIO_VALUE(IOPRIO_CLASS_IDLE, 0)); */
syscall(SYS_ioprio_set, 1, 0, 0x6000);

nproc = sysconf(_SC_NPROCESSORS_ONLN);

for (i = 0; i < nproc; i++) {
pid = fork();
assert(pid != -1);
if (pid == 0) {
for (;;) {
pid = fork();
assert(pid != -1);
if (pid == 0) {
_exit(0);
} else {
child = wait(NULL);
assert(child == pid);
}
}
}

pid = fork();
assert(pid != -1);
if (pid == 0) {
for (;;) {
/* ioprio_get(IOPRIO_WHO_PGRP, 0); */
syscall(SYS_ioprio_get, 2, 0);
}
}
}

for (;;) {
/* ioprio_get(IOPRIO_WHO_PGRP, 0); */
syscall(SYS_ioprio_get, 2, 0);
}

return 0;
}

This gets us KASAN dumps like this:

[   35.526914] ==================================================================
[   35.530009] BUG: KASAN: out-of-bounds in get_task_ioprio+0x7b/0x90 at addr ffff880066f34e6c
[   35.530009] Read of size 2 by task ioprio-gpf/363
[   35.530009] =============================================================================
[   35.530009] BUG blkdev_ioc (Not tainted): kasan: bad access detected
[   35.530009] -----------------------------------------------------------------------------

[   35.530009] Disabling lock debugging due to kernel taint
[   35.530009] INFO: Allocated in create_task_io_context+0x2b/0x370 age=0 cpu=0 pid=360
[   35.530009]  ___slab_alloc+0x55d/0x5a0
[   35.530009]  __slab_alloc.isra.20+0x2b/0x40
[   35.530009]  kmem_cache_alloc_node+0x84/0x200
[   35.530009]  create_task_io_context+0x2b/0x370
[   35.530009]  get_task_io_context+0x92/0xb0
[   35.530009]  copy_process.part.8+0x5029/0x5660
[   35.530009]  _do_fork+0x155/0x7e0
[   35.530009]  SyS_clone+0x19/0x20
[   35.530009]  do_syscall_64+0x195/0x3a0
[   35.530009]  return_from_SYSCALL_64+0x0/0x6a
[   35.530009] INFO: Freed in put_io_context+0xe7/0x120 age=0 cpu=0 pid=1060
[   35.530009]  __slab_free+0x27b/0x3d0
[   35.530009]  kmem_cache_free+0x1fb/0x220
[   35.530009]  put_io_context+0xe7/0x120
[   35.530009]  put_io_context_active+0x238/0x380
[   35.530009]  exit_io_context+0x66/0x80
[   35.530009]  do_exit+0x158e/0x2b90
[   35.530009]  do_group_exit+0xe5/0x2b0
[   35.530009]  SyS_exit_group+0x1d/0x20
[   35.530009]  entry_SYSCALL_64_fastpath+0x1a/0xa4
[   35.530009] INFO: Slab 0xffffea00019bcd00 objects=20 used=4 fp=0xffff880066f34ff0 flags=0x1fffe0000004080
[   35.530009] INFO: Object 0xffff880066f34e58 @offset=3672 fp=0x0000000000000001
[   35.530009] ==================================================================

Fix it by grabbing the task lock while we poke at the io_context.

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qeth: delete napi struct when removing a qeth device

commit 7831b4ff0d926e0deeaabef9db8800ed069a2757 upstream.

A qeth_card contains a napi_struct linked to the net_device during
device probing. This struct must be deleted when removing the qeth
device, otherwise Panic on oops can occur when qeth devices are
repeatedly removed and added.

Fixes: a1c3ed4c9ca ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Tested-by: Alexander Klein <ALKL@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/chrome: cros_ec_dev - double fetch bug in ioctl

commit 096cdc6f52225835ff503f987a0d68ef770bb78e upstream.

We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure
that those values have not changed between the two copy_from_user()
calls.  Otherwise it could lead to a buffer overflow.

Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value.
We should use the new smaller value so we don't copy too much data to
the user.

Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: a841178445bb ('mfd: cros_ec: Use a zero-length array for command data')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: rockchip: initialize flags of clk_init_data in mmc-phase clock

commit 595144c1141c951a3c6bb9004ae6a2bc29aad66f upstream.

The flags element of clk_init_data was never initialized for mmc-
phase-clocks resulting in the element containing a random value
and thus possibly enabling unwanted clock flags.

Fixes: 89bf26cbc1a0 ("clk: rockchip: Add support for the mmc clock phases using the framework")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: sun4i: fix FIFO limit

commit 6d9fe44bd73d567d04d3a68a2d2fa521ab9532f2 upstream.

When testing SPI without DMA I noticed that filling the FIFO on the
spi controller causes timeout.

Always leave room for one byte in the FIFO.

Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: sunxi: fix transfer timeout

commit 719bd6542044efd9b338a53dba1bef45f40ca169 upstream.

The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.

Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

namespace: update event counter when umounting a deleted dentry

commit e06b933e6ded42384164d28a2060b7f89243b895 upstream.

- m_start() in fs/namespace.c expects that ns->event is incremented each
  time a mount added or removed from ns->list.
- umount_tree() removes items from the list but does not increment event
  counter, expecting that it's done before the function is called.
- There are some codepaths that call umount_tree() without updating
  "event" counter. e.g. from __detach_mounts().
- When this happens m_start may reuse a cached mount structure that no
  longer belongs to ns->list (i.e. use after free which usually leads
  to infinite loop).

This change fixes the above problem by incrementing global event counter
before invoking umount_tree().

Change-Id: I622c8e84dcb9fb63542372c5dbf0178ee86bb589
Signed-off-by: Andrey Ulanov <andreyu@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

9p: use file_dentry()

commit b403f0e37a11f84f7ceaf40b0075499e5bcfd220 upstream.

v9fs may be used as lower layer of overlayfs and accessing f_path.dentry
can lead to a crash.  In this case it's a NULL pointer dereference in
p9_fid_create().

Fix by replacing direct access of file->f_path.dentry with the
file_dentry() accessor, which will always return a native object.

Reported-by: Alessio Igor Bogani <alessioigorbogani@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Tested-by: Alessio Igor Bogani <alessioigorbogani@gmail.com>
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: verify extent header depth

commit 7bc9491645118c9461bd21099c31755ff6783593 upstream.

Although the extent tree depth of 5 should enough be for the worst
case of 2*32 extents of length 1, the extent tree code does not
currently to merge nodes which are less than half-full with a sibling
node, or to shrink the tree depth if possible.  So it's possible, at
least in theory, for the tree depth to be greater than 5.  However,
even in the worst case, a tree depth of 32 is highly unlikely, and if
the file system is maliciously corrupted, an insanely large eh_depth
can cause memory allocation failures that will trigger kernel warnings
(here, eh_depth = 65280):

    JBD2: ext4.exe wants too many credits credits:195849 rsv_credits:0 max:256
    ------------[ cut here ]------------
    WARNING: CPU: 0 PID: 50 at fs/jbd2/transaction.c:293 start_this_handle+0x569/0x580
    CPU: 0 PID: 50 Comm: ext4.exe Not tainted 4.7.0-rc5+ #508
    Stack:
     604a8947 625badd8 0002fd09 00000000
     60078643 00000000 62623910 601bf9bc
     62623970 6002fc84 626239b0 900000125
    Call Trace:
     [<6001c2dc>] show_stack+0xdc/0x1a0
     [<601bf9bc>] dump_stack+0x2a/0x2e
     [<6002fc84>] __warn+0x114/0x140
     [<6002fdff>] warn_slowpath_null+0x1f/0x30
     [<60165829>] start_this_handle+0x569/0x580
     [<60165d4e>] jbd2__journal_start+0x11e/0x220
     [<60146690>] __ext4_journal_start_sb+0x60/0xa0
     [<60120a81>] ext4_truncate+0x131/0x3a0
     [<60123677>] ext4_setattr+0x757/0x840
     [<600d5d0f>] notify_change+0x16f/0x2a0
     [<600b2b16>] do_truncate+0x76/0xc0
     [<600c3e56>] path_openat+0x806/0x1300
     [<600c55c9>] do_filp_open+0x89/0xf0
     [<600b4074>] do_sys_open+0x134/0x1e0
     [<600b4140>] SyS_open+0x20/0x30
     [<6001ea68>] handle_syscall+0x88/0x90
     [<600295fd>] userspace+0x3fd/0x500
     [<6001ac55>] fork_handler+0x85/0x90

    ---[ end trace 08b0b88b6387a244 ]---

[ Commit message modified and the extent tree depath check changed
from 5 to 32 -- tytso ]

Cc: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ecryptfs: don't allow mmap when the lower fs doesn't support it

commit f0fe970df3838c202ef6c07a4c2b36838ef0a88b upstream.

There are legitimate reasons to disallow mmap on certain files, notably
in sysfs or procfs.  We shouldn't emulate mmap support on file systems
that don't offer support natively.

CVE-2016-1583

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
[tyhicks: clean up f_op check by using ecryptfs_file_to_lower()]
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "ecryptfs: forbid opening files without mmap handler"

commit 78c4e172412de5d0456dc00d2b34050aa0b683b5 upstream.

This reverts commit 2f36db71009304b3f0b95afacd8eba1f9f046b87.

It fixed a local root exploit but also introduced a dependency on
the lower file system implementing an mmap operation just to open a file,
which is a bit of a heavy hammer.  The right fix is to have mmap depend
on the existence of the mmap handler instead.

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locks: use file_inode()

commit 6343a2120862f7023006c8091ad95c1f16a32077 upstream.

(Another one for the f_path debacle.)

ltp fcntl33 testcase caused an Oops in selinux_file_send_sigiotask.

The reason is that generic_add_lease() used filp->f_path.dentry->inode
while all the others use file_inode().  This makes a difference for files
opened on overlayfs since the former will point to the overlay inode the
latter to the underlying inode.

So generic_add_lease() added the lease to the overlay inode and
generic_delete_lease() removed it from the underlying inode.  When the file
was released the lease remained on the overlay inode's lock list, resulting
in use after free.

Reported-by: Eryu Guan <eguan@redhat.com>
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power_supply: power_supply_read_temp only if use_cnt > 0

commit 5bc28b93a36e3cb3acc2870fb75cb6ffb182fece upstream.

Change power_supply_read_temp() to use power_supply_get_property()
so that it will check the use_cnt and ensure it is > 0. The use_cnt
will be incremented at the end of __power_supply_register, so this
will block to case where get_property can be called before the supply
is fully registered. This fixes the issue show in the stack below:

[    1.452598] power_supply_read_temp+0x78/0x80
[    1.458680] thermal_zone_get_temp+0x5c/0x11c
[    1.464765] thermal_zone_device_update+0x34/0xb4
[    1.471195] thermal_zone_device_register+0x87c/0x8cc
[    1.477974] __power_supply_register+0x364/0x424
[    1.484317] power_supply_register_no_ws+0x10/0x18
[    1.490833] bq27xxx_battery_setup+0x10c/0x164
[    1.497003] bq27xxx_battery_i2c_probe+0xd0/0x1b0
[    1.503435] i2c_device_probe+0x174/0x240
[    1.509172] driver_probe_device+0x1fc/0x29c
[    1.515167] __driver_attach+0xa4/0xa8
[    1.520643] bus_for_each_dev+0x58/0x98
[    1.526204] driver_attach+0x20/0x28
[    1.531505] bus_add_driver+0x1c8/0x22c
[    1.537067] driver_register+0x68/0x108
[    1.542630] i2c_register_driver+0x38/0x7c
[    1.548457] bq27xxx_battery_i2c_driver_init+0x18/0x20
[    1.555321] do_one_initcall+0x38/0x12c
[    1.560886] kernel_init_freeable+0x148/0x1ec
[    1.566972] kernel_init+0x10/0xfc
[    1.572101] ret_from_fork+0x10/0x40

Also make the same change to ps_get_max_charge_cntl_limit() and
ps_get_cur_chrage_cntl_limit() to be safe. Lastly, change the return
value of power_supply_get_property() to -EAGAIN from -ENODEV if
use_cnt <= 0.

Fixes: 297d716f6260 ("power_supply: Change ownership from driver to core")
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cgroup: set css->id to -1 during init

commit 8fa3b8d689a54d6d04ff7803c724fb7aca6ce98e upstream.

If percpu_ref initialization fails during css_create(), the free path
can end up trying to free css->id of zero.  As ID 0 is unused, it
doesn't cause a critical breakage but it does trigger a warning
message.  Fix it by setting css->id to -1 from init_and_link_css().

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Wenwei Tao <ww.tao0320@gmail.com>
Fixes: 01e586598b22 ("cgroup: release css->id after css_free")
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: imx: Do not treat a PIN without MUX register as an error

commit ba562d5e54fd3136bfea0457add3675850247774 upstream.

Some PINs do not have a MUX register, it is not an error.
It is necessary to allow the continuation of the PINs configuration,
otherwise the whole PIN-group will be configured incorrectly.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: single: Fix missing flush of posted write for a wakeirq

commit 0ac3c0a4025f41748a083bdd4970cb3ede802b15 upstream.

With many repeated suspend resume cycles, the pin specific wakeirq
may not always work on omaps. This is because the write to enable the
pin interrupt may not have reached the device over the interconnect
before suspend happens.

Let's fix the issue with a flush of posted write with a readback.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pvclock: Add CPU barriers to get correct version value

commit 749d088b8e7f4b9826ede02b9a043e417fa84aa1 upstream.

Protocol for the "version" fields is: hypervisor raises it (making it
uneven) before it starts updating the fields and raises it again (making
it even) when it is done.  Thus the guest can make sure the time values
it got are consistent by checking the version before and after reading
them.

Add CPU barries after getting version value just like what function
vread_pvclock does, because all of callees in this function is inline.

Fixes: 502dfeff239e8313bfbe906ca0a1a6827ac8481b
Signed-off-by: Minfei Huang <mnghuan@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: tsc200x - report proper input_dev name

commit e9003c9cfaa17d26991688268b04244adb67ee2b upstream.

Passes input_id struct to the common probe function for the tsc200x drivers
instead of just the bustype.

This allows for the use of the product variable to set the input_dev->name
variable according to the type of touchscreen used. Note that when we
introduced support for TSC2004 we started calling everything TSC200X, so
let's keep this quirk.

Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: xpad - validate USB endpoint count during probe

commit caca925fca4fb30c67be88cacbe908eec6721e43 upstream.

This prevents a malicious USB device from causing an oops.

Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: wacom_w8001 - w8001_MAX_LENGTH should be 13

commit 12afb34400eb2b301f06b2aa3535497d14faee59 upstream.

Somehow the patch that added two-finger touch support forgot to update
W8001_MAX_LENGTH from 11 to 13.

Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: xpad - fix oops when attaching an unknown Xbox One gamepad

commit c7f1429389ec1aa25e042bb13451385fbb596f8c upstream.

Xbox One controllers have multiple interfaces which all have the
same class, subclass, and protocol. One of the these interfaces
has only a single endpoint. When Xpad attempts to bind to this
interface, it causes an oops when trying initialize the output URB
by trying to access the second endpoint's descriptor.

This situation was avoided for known Xbox One devices by checking
the XTYPE constant associated with the VID and PID tuple. However,
this breaks when new or previously unknown Xbox One controllers
are attached to the system.

This change addresses the problem by deriving the XTYPE for Xbox
One controllers based on the interface protocol before checking
the interface number.

Fixes: 1a48ff81b391 ("Input: xpad - add support for Xbox One controllers")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: elantech - add more IC body types to the list

commit 226ba707744a51acb4244724e09caacb1d96aed9 upstream.

The touchpad in HP Pavilion 14-ab057ca reports it's version as 12 and
according to Elan both 11 and 12 are valid IC types and should be
identified as hw_version 4.

Reported-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Tested-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: vmmouse - remove port reservation

commit 60842ef8128e7bf58c024814cd0dc14319232b6c upstream.

The VMWare EFI BIOS will expose port 0x5658 as an ACPI resource.  This
causes the port to be reserved by the APCI module as the system comes up,
making it unavailable to be reserved again by other drivers, thus
preserving this VMWare port for special use in a VMWare guest.

This port is designed to be shared among multiple VMWare services, such as
the VMMOUSE.  Because of this, VMMOUSE should not try to reserve this port
on its own.

The VMWare non-EFI BIOS does not do this to preserve compatibility with
existing/legacy VMs.  It is known that there is small chance a VM may be
configured such that these ports get reserved by other non-VMWare devices,
and if this ever happens, the result is undefined.

Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: timer: Fix leak in events via snd_timer_user_tinterrupt

commit e4ec8cc8039a7063e24204299b462bd1383184a5 upstream.

The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.

Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: timer: Fix leak in events via snd_timer_user_ccallback

commit 9a47e9cff994f37f7f0dbd9ae23740d0f64f9fe6 upstream.

The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.

Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: timer: Fix leak in SNDRV_TIMER_IOCTL_PARAMS

commit cec8f96e49d9be372fdb0c3836dcf31ec71e457e upstream.

The stack object “tread” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.

Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xenbus: don't bail early from xenbus_dev_request_and_reply()

commit 7469be95a487319514adce2304ad2af3553d2fc9 upstream.

xenbus_dev_request_and_reply() needs to track whether a transaction is
open.  For XS_TRANSACTION_START messages it calls transaction_start()
and for XS_TRANSACTION_END messages it calls transaction_end().

If sending an XS_TRANSACTION_START message fails or responds with an
an error, the transaction is not open and transaction_end() must be
called.

If sending an XS_TRANSACTION_END message fails, the transaction is
still open, but if an error response is returned the transaction is
closed.

Commit 027bd7e89906 ("xen/xenbus: Avoid synchronous wait on XenBus
stalling shutdown/restart") introduced a regression where failed
XS_TRANSACTION_START messages were leaving the transaction open.  This
can cause problems with suspend (and migration) as all transactions
must be closed before suspending.

It appears that the problematic change was added accidentally, so just
remove it.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xenbus: don't BUG() on user mode induced condition

commit 0beef634b86a1350c31da5fcc2992f0d7c8a622b upstream.

Inability to locate a user mode specified transaction ID should not
lead to a kernel crash. For other than XS_TRANSACTION_START also
don't issue anything to xenbus if the specified ID doesn't match that
of any active transaction.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/pciback: Fix conf_space read/write overlap check.

commit 02ef871ecac290919ea0c783d05da7eedeffc10e upstream.

Current overlap check is evaluating to false a case where a filter
field is fully contained (proper subset) of a r/w request.  This
change applies classical overlap check instead to include all the
scenarios.

More specifically, for (Hilscher GmbH CIFX 50E-DP(M/S)) device driver
the logic is such that the entire confspace is read and written in 4
byte chunks. In this case as an example, CACHE_LINE_SIZE,
LATENCY_TIMER and PCI_BIST are arriving together in one call to
xen_pcibk_config_write() with offset == 0xc and size == 4.  With the
exsisting overlap check the LATENCY_TIMER field (offset == 0xd, length
== 1) is fully contained in the write request and hence is excluded
from write, which is incorrect.

Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: unwind: ensure that .debug_frame is generated (vs. .eh_frame)

commit f52e126cc7476196f44f3c313b7d9f0699a881fc upstream.

With recent binutils update to support dwarf CFI pseudo-ops in gas, we
now get .eh_frame vs. .debug_frame. Although the call frame info is
exactly the same in both, the CIE differs, which the current kernel
unwinder can't cope with.

This broke both the kernel unwinder as well as loadable modules (latter
because of a new unhandled relo R_ARC_32_PCREL from .rela.eh_frame in
the module loader)

The ideal solution would be to switch unwinder to .eh_frame.
For now however we can make do by just ensureing .debug_frame is
generated by removing -fasynchronous-unwind-tables

 .eh_frame    generated with -gdwarf-2 -fasynchronous-unwind-tables
 .debug_frame generated with -gdwarf-2

Fixes STAR 9001058196

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arc: unwind: warn only once if DW2_UNWIND is disabled

commit 9bd54517ee86cb164c734f72ea95aeba4804f10b upstream.

If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core()
gets called following message gets printed in debug console:
----------------->8---------------
CONFIG_ARC_DW2_UNWIND needs to be enabled
----------------->8---------------

That message makes sense if user indeed wants to see a backtrace or
get nice function call-graphs in perf but what if user disabled
unwinder for the purpose? Why pollute his debug console?

So instead we'll warn user about possibly missing feature once and
let him decide if that was what he or she really wanted.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernel/sysrq, watchdog, sched/core: Reset watchdog on all CPUs while processing sysrq-w

commit 57675cb976eff977aefb428e68e4e0236d48a9ff upstream.

Lengthy output of sysrq-w may take a lot of time on slow serial console.

Currently we reset NMI-watchdog on the current CPU to avoid spurious
lockup messages. Sometimes this doesn't work since softlockup watchdog
might trigger on another CPU which is waiting for an IPI to proceed.
We reset softlockup watchdogs on all CPUs, but we do this only after
listing all tasks, and this may be too late on a busy system.

So, reset watchdogs CPUs earlier, in for_each_process_thread() loop.

Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1465474805-14641-1-git-send-email-aryabinin@virtuozzo.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pps: do not crash when failed to register

commit 368301f2fe4b07e5fb71dba3cc566bc59eb6705f upstream.

With this command sequence:

  modprobe plip
  modprobe pps_parport
  rmmod pps_parport

the partport_pps modules causes this crash:

  BUG: unable to handle kernel NULL pointer dereference at (null)
  IP: parport_detach+0x1d/0x60 [pps_parport]
  Oops: 0000 [#1] SMP
  ...
  Call Trace:
    parport_unregister_driver+0x65/0xc0 [parport]
    SyS_delete_module+0x187/0x210

The sequence that builds up to this is:

 1) plip is loaded and takes the parport device for exclusive use:

    plip0: Parallel port at 0x378, using IRQ 7.

 2) pps_parport then fails to grab the device:

    pps_parport: parallel port PPS client
    parport0: cannot grant exclusive access for device pps_parport
    pps_parport: couldn't register with parport0

 3) rmmod of pps_parport is then killed because it tries to access
    pardev->name, but pardev (taken from port->cad) is NULL.

So add a check for NULL in the test there too.

Link: http://lkml.kernel.org/r/20160714115245.12651-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vmlinux.lds: account for destructor sections

commit e41f501d391265ff568f3e49d6128cc30856a36f upstream.

If CONFIG_KASAN is enabled and gcc is configured with
--disable-initfini-array and/or gold linker is used, gcc emits
.ctors/.dtors and .text.startup/.text.exit sections instead of
.init_array/.fini_array.  .dtors section is not explicitly accounted in
the linker script and messes vvar/percpu layout.

We want:
  ffffffff822bfd80 D _edata
  ffffffff822c0000 D __vvar_beginning_hack
  ffffffff822c0000 A __vvar_page
  ffffffff822c0080 0000000000000098 D vsyscall_gtod_data
  ffffffff822c1000 A __init_begin
  ffffffff822c1000 D init_per_cpu__irq_stack_union
  ffffffff822c1000 A __per_cpu_load
  ffffffff822d3000 D init_per_cpu__gdt_page

We got:
  ffffffff8279a600 D _edata
  ffffffff8279b000 A __vvar_page
  ffffffff8279c000 A __init_begin
  ffffffff8279c000 D init_per_cpu__irq_stack_union
  ffffffff8279c000 A __per_cpu_load
  ffffffff8279e000 D __vvar_beginning_hack
  ffffffff8279e080 0000000000000098 D vsyscall_gtod_data
  ffffffff827ae000 D init_per_cpu__gdt_page

This happens because __vvar_page and .vvar get different addresses in
arch/x86/kernel/vmlinux.lds.S:

. = ALIGN(PAGE_SIZE);
__vvar_page = .;

.vvar : AT(ADDR(.vvar) - LOAD_OFFSET) {
/* work around gold bug 13023 */
__vvar_beginning_hack = .;

Discard .dtors/.fini_array/.text.exit, since we don't call dtors.
Merge .text.startup into init text.

Link: http://lkml.kernel.org/r/1467386363-120030-1-git-send-email-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, meminit: ensure node is online before checking whether pages are uninitialised

commit ef70b6f41cda6270165a6f27b2548ed31cfa3cb2 upstream.

early_page_uninitialised looks up an arbitrary PFN.  While a machine
without node 0 will boot with "mm, page_alloc: Always return a valid
node from early_pfn_to_nid", it works because it assumes that nodes are
always in PFN order.  This is not guaranteed so this patch adds
robustness by always checking if the node being checked is online.

Link: http://lkml.kernel.org/r/1468008031-3848-4-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, meminit: always return a valid node from early_pfn_to_nid

commit e4568d3803852d00effd41dcdd489e726b998879 upstream.

early_pfn_to_nid can return node 0 if a PFN is invalid on machines that
has no node 0.  A machine with only node 1 was observed to crash with
the following message:

   BUG: unable to handle kernel paging request at 000000000002a3c8
   PGD 0
   Modules linked in:
   Hardware name: Supermicro H8DSP-8/H8DSP-8, BIOS 080011  06/30/2006
   task: ffffffff81c0d500 ti: ffffffff81c00000 task.ti: ffffffff81c00000
   RIP: reserve_bootmem_region+0x6a/0xef
   CR2: 000000000002a3c8 CR3: 0000000001c06000 CR4: 00000000000006b0
   Call Trace:
      free_all_bootmem+0x4b/0x12a
      mem_init+0x70/0xa3
      start_kernel+0x25b/0x49b

The problem is that early_page_uninitialised uses the early_pfn_to_nid
helper which returns node 0 for invalid PFNs.  No caller of
early_pfn_to_nid cares except early_page_uninitialised.  This patch has
early_pfn_to_nid always return a valid node.

Link: http://lkml.kernel.org/r/1468008031-3848-3-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, compaction: prevent VM_BUG_ON when terminating freeing scanner

commit a46cbf3bc53b6a93fb84a5ffb288c354fa807954 upstream.

It's possible to isolate some freepages in a pageblock and then fail
split_free_page() due to the low watermark check.  In this case, we hit
VM_BUG_ON() because the freeing scanner terminated early without a
contended lock or enough freepages.

This should never have been a VM_BUG_ON() since it's not a fatal
condition.  It should have been a VM_WARN_ON() at best, or even handled
gracefully.

Regardless, we need to terminate anytime the full pageblock scan was not
done.  The logic belongs in isolate_freepages_block(), so handle its
state gracefully by terminating the pageblock loop and making a note to
restart at the same pageblock next time since it was not possible to
complete the scan this time.

[rientjes@google.com: don't rescan pages in a pageblock]
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1607111244150.83138@chino.kir.corp.google.com
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1606291436300.145590@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Minchan Kim <minchan@kernel.org>
Tested-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs/nilfs2: fix potential underflow in call to crc32_le

commit 63d2f95d63396059200c391ca87161897b99e74a upstream.

The value `bytes' comes from the filesystem which is about to be
mounted.  We cannot trust that the value is always in the range we
expect it to be.

Check its value before using it to calculate the length for the crc32_le
call.  It value must be larger (or equal) sumoff + 4.

This fixes a kernel bug when accidentially mounting an image file which
had the nilfs2 magic value 0x3434 at the right offset 0x406 by chance.
The bytes 0x01 0x00 were stored at 0x408 and were interpreted as a
s_bytes value of 1.  This caused an underflow when substracting sumoff +
4 (20) in the call to crc32_le.

  BUG: unable to handle kernel paging request at ffff88021e600000
  IP:  crc32_le+0x36/0x100
  ...
  Call Trace:
    nilfs_valid_sb.part.5+0x52/0x60 [nilfs2]
    nilfs_load_super_block+0x142/0x300 [nilfs2]
    init_nilfs+0x60/0x390 [nilfs2]
    nilfs_mount+0x302/0x520 [nilfs2]
    mount_fs+0x38/0x160
    vfs_kern_mount+0x67/0x110
    do_mount+0x269/0xe00
    SyS_mount+0x9f/0x100
    entry_SYSCALL_64_fastpath+0x16/0x71

Link: http://lkml.kernel.org/r/1466778587-5184-2-git-send-email-konishi.ryusuke@lab.ntt.co.jp
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Tested-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, compaction: abort free scanner if split fails

commit a4f04f2c6955aff5e2c08dcb40aca247ff4d7370 upstream.

If the memory compaction free scanner cannot successfully split a free
page (only possible due to per-zone low watermark), terminate the free
scanner rather than continuing to scan memory needlessly.  If the
watermark is insufficient for a free page of order <= cc->order, then
terminate the scanner since all future splits will also likely fail.

This prevents the compaction freeing scanner from scanning all memory on
very large zones (very noticeable for zones > 128GB, for instance) when
all splits will likely fail while holding zone->lock.

compaction_alloc() iterating a 128GB zone has been benchmarked to take
over 400ms on some systems whereas any free page isolated and ready to
be split ends up failing in split_free_page() because of the low
watermark check and thus the iteration continues.

The next time compaction occurs, the freeing scanner will likely start
at the end of the zone again since no success was made previously and we
get the same lengthy iteration until the zone is brought above the low
watermark.  All thp page faults can take >400ms in such a state without
this fix.

Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1606211820350.97086@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, sl[au]b: add __GFP_ATOMIC to the GFP reclaim mask

commit e838a45f9392a5bd2be1cd3ab0b16ae85857461c upstream.

Commit d0164adc89f6 ("mm, page_alloc: distinguish between being unable
to sleep, unwilling to sleep and avoiding waking kswapd") modified
__GFP_WAIT to explicitly identify the difference between atomic callers
and those that were unwilling to sleep.  Later the definition was
removed entirely.

The GFP_RECLAIM_MASK is the set of flags that affect watermark checking
and reclaim behaviour but __GFP_ATOMIC was never added.  Without it,
atomic users of the slab allocator strip the __GFP_ATOMIC flag and
cannot access the page allocator atomic reserves.  This patch addresses
the problem.

The user-visible impact depends on the workload but potentially atomic
allocations unnecessarily fail without this path.

Link: http://lkml.kernel.org/r/20160610093832.GK2527@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: at_xdmac: double FIFO flush needed to compute residue

commit 9295c41d77ca93aac79cfca6fa09fa1ca5cab66f upstream.

Due to the way CUBC register is updated, a double flush is needed to
compute an accurate residue. First flush aim is to get data from the DMA
FIFO and second one ensures that we won't report data which are not in
memory.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: at_xdmac: fix residue corruption

commit 53398f488821c2b5b15291e3debec6ad33f75d3d upstream.

An unexpected value of CUBC can lead to a corrupted residue. A more
complex sequence is needed to detect an inaccurate value for NCA or CUBC.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: at_xdmac: align descriptors on 64 bits

commit 4a9723e8df68cfce4048517ee32e37f78854b6fb upstream.

Having descriptors aligned on 64 bits allows update CNDA and CUBC in an
atomic way.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/quirks: Add early quirk to reset Apple AirPort card

commit abb2bafd295fe962bbadc329dbfb2146457283ac upstream.

The EFI firmware on Macs contains a full-fledged network stack for
downloading OS X images from osrecovery.apple.com. Unfortunately
on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331
wireless card on every boot and leaves it enabled even after
ExitBootServices has been called. The card continues to assert its IRQ
line, causing spurious interrupts if the IRQ is shared. It also corrupts
memory by DMAing received packets, allowing for remote code execution
over the air. This only stops when a driver is loaded for the wireless
card, which may be never if the driver is not installed or blacklisted.

The issue seems to be constrained to the Broadcom 4331. Chris Milsted
has verified that the newer Broadcom 4360 built into the MacBookPro11,3
(2013/2014) does not exhibit this behaviour. The chances that Apple will
ever supply a firmware fix for the older machines appear to be zero.

The solution is to reset the card on boot by writing to a reset bit in
its mmio space. This must be done as an early quirk and not as a plain
vanilla PCI quirk to successfully combat memory corruption by DMAed
packets: Matthew Garrett found out in 2012 that the packets are written
to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html).
This type of memory is made available to the page allocator by
efi_free_boot_services(). Plain vanilla PCI quirks run much later, in
subsys initcall level. In-between a time window would be open for memory
corruption. Random crashes occurring in this time window and attributed
to DMAed packets have indeed been observed in the wild by Chris
Bainbridge.

When Matthew Garrett analyzed the memory corruption issue in 2012, he
sought to fix it with a grub quirk which transitions the card to D3hot:
http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56

This approach does not help users with other bootloaders and while it
may prevent DMAed packets, it does not cure the spurious interrupts
emanating from the card. Unfortunately the card's mmio space is
inaccessible in D3hot, so to reset it, we have to undo the effect of
Matthew's grub patch and transition the card back to D0.

Note that the quirk takes a few shortcuts to reduce the amount of code:
The size of BAR 0 and the location of the PM capability is identical
on all affected machines and therefore hardcoded. Only the address of
BAR 0 differs between models. Also, it is assumed that the BCMA core
currently mapped is the 802.11 core. The EFI driver seems to always take
care of this.

Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback
towards finding the best solution to this problem.

The following should be a comprehensive list of affected models:
    iMac13,1        2012  21.5"       [Root Port 00:1c.3 = 8086:1e16]
    iMac13,2        2012  27"         [Root Port 00:1c.3 = 8086:1e16]
    Macmini5,1      2011  i5 2.3 GHz  [Root Port 00:1c.1 = 8086:1c12]
    Macmini5,2      2011  i5 2.5 GHz  [Root Port 00:1c.1 = 8086:1c12]
    Macmini5,3      2011  i7 2.0 GHz  [Root Port 00:1c.1 = 8086:1c12]
    Macmini6,1      2012  i5 2.5 GHz  [Root Port 00:1c.1 = 8086:1e12]
    Macmini6,2      2012  i7 2.3 GHz  [Root Port 00:1c.1 = 8086:1e12]
    MacBookPro8,1   2011  13"         [Root Port 00:1c.1 = 8086:1c12]
    MacBookPro8,2   2011  15"         [Root Port 00:1c.1 = 8086:1c12]
    MacBookPro8,3   2011  17"         [Root Port 00:1c.1 = 8086:1c12]
    MacBookPro9,1   2012  15"         [Root Port 00:1c.1 = 8086:1e12]
    MacBookPro9,2   2012  13"         [Root Port 00:1c.1 = 8086:1e12]
    MacBookPro10,1  2012  15"         [Root Port 00:1c.1 = 8086:1e12]
    MacBookPro10,2  2012  13"         [Root Port 00:1c.1 = 8086:1e12]

For posterity, spurious interrupts caused by the Broadcom 4331 wireless
card resulted in splats like this (stacktrace omitted):

    irq 17: nobody cared (try booting with the "irqpoll" option)
    handlers:
    [<ffffffff81374370>] pcie_isr
    [<ffffffffc0704550>] sdhci_irq [sdhci] threaded [<ffffffffc07013c0>] sdhci_thread_irq [sdhci]
    [<ffffffffc0a0b960>] azx_interrupt [snd_hda_codec]
    Disabling IRQ #17

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79301
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111781
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=728916
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=895951#c16
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1009819
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1098621
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1149632#c5
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1279130
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1332732
Tested-by: Konstantin Simanov <k.simanov@stlk.ru> # [MacBookPro8,1]
Tested-by: Lukas Wunner <lukas@wunner.de> # [MacBookPro9,1]
Tested-by: Bryan Paradis <bryan.paradis@gmail.com> # [MacBookPro9,2]
Tested-by: Andrew Worsley <amworsley@gmail.com> # [MacBookPro10,1]
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com> # [MacBookPro10,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris Milsted <cmilsted@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Michael Buesch <m@bues.ch>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: b43-dev@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Link: http://lkml.kernel.org/r/48d0972ac82a53d460e5fce77a07b2560db95203.1465690253.git.lukas@wunner.de
[ Did minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/quirks: Reintroduce scanning of secondary buses

commit 850c321027c2e31d0afc71588974719a4b565550 upstream.

We used to scan secondary buses until the following commit that
was applied in 2009:

  8659c406ade3 ("x86: only scan the root bus in early PCI quirks")

which commit constrained early quirks to the root bus only. Its
motivation was to prevent application of the nvidia_bugs quirk
on secondary buses.

We're about to add a quirk to reset the Broadcom 4331 wireless card on
2011/2012 Macs, which is located on a secondary bus behind a PCIe root
port. To facilitate that, reintroduce scanning of secondary buses.

The commit message of 8659c406ade3 notes that scanning only the root bus
"saves quite some unnecessary scanning work". The algorithm used prior
to 8659c406ade3 was particularly time consuming because it scanned
buses 0 to 31 brute force. To avoid lengthening boot time, employ a
recursive strategy which only scans buses that are actually reachable
from the root bus.

Yinghai Lu pointed out that the secondary bus number read from a
bridge's config space may be invalid, in particular a value of 0 would
cause an infinite loop. The PCI core goes beyond that and recurses to a
child bus only if its bus number is greater than the parent bus number
(see pci_scan_bridge()). Since the root bus is numbered 0, this implies
that secondary buses may not be 0. Do the same on early scanning.

If this algorithm is found to significantly impact boot time or cause
infinite loops on broken hardware, it would be possible to limit its
recursion depth: The Broadcom 4331 quirk applies at depth 1, all others
at depth 0, so the bus need not be scanned deeper than that for now. An
alternative approach would be to revert to scanning only the root bus,
and apply the Broadcom 4331 quirk to the root ports 8086:1c12, 8086:1e12
and 8086:1e16. Apple always positioned the card behind either of these
three ports. The quirk would then check presence of the card in slot 0
below the root port and do its deed.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/f0daa70dac1a9b2483abdb31887173eb6ab77bdf.1465690253.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/quirks: Apply nvidia_bugs quirk only on root bus

commit 447d29d1d3aed839e74c2401ef63387780ac51ed upstream.

Since the following commit:

  8659c406ade3 ("x86: only scan the root bus in early PCI quirks")

... early quirks are only applied to devices on the root bus.

The motivation was to prevent application of the nvidia_bugs quirk on
secondary buses.

We're about to reintroduce scanning of secondary buses for a quirk to
reset the Broadcom 4331 wireless card on 2011/2012 Macs. To prevent
regressions, open code the requirement to apply nvidia_bugs only on the
root bus.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/4d5477c1d76b2f0387a780f2142bbcdd9fee869b.1465690253.git.lukas@wunner.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: OHCI: Don't mark EDs as ED_OPER if scheduling fails

commit c66f59ee5050447b3da92d36f5385a847990a894 upstream.

Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.

This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.

The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.

Fix ed_schedule to update ED state only on successful return.

Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.4.16

ovl: verify upper dentry before unlink and rename

commit 11f3710417d026ea2f4fcf362d866342c5274185 upstream.

Unlink and rename in overlayfs checked the upper dentry for staleness by
verifying upper->d_parent against upperdir.  However the dentry can go
stale also by being unhashed, for example.

Expand the verification to actually look up the name again (under parent
lock) and check if it matches the upper dentry.  This matches what the VFS
does before passing the dentry to filesytem's unlink/rename methods, which
excludes any inconsistency caused by overlayfs.

Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Revert DisplayPort fast link training feature

commit 34511dce4b35685d3988d5c8b100d11a068db5bd upstream.

It has been found out that in some HW combination the DisplayPort
fast link training feature caused screen flickering. Let's revert
this feature for now until we can ensure that the feature works for
all platforms.

This is a manual revert of commits 5fa836a9d859 ("drm/i915: DP link
training optimization") and 4e96c97742f4 ("drm/i915: eDP link training
optimization").

Fixes: 5fa836a9d859 ("drm/i915: DP link training optimization")
Fixes: 4e96c97742f4 ("drm/i915: eDP link training optimization")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466410226-19543-1-git-send-email-mika.kahola@intel.com
(cherry picked from commit 91df09d92ad82c8778ca218097bf827f154292ca)
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tmpfs: fix regression hang in fallocate undo

commit 7f556567036cb7f89aabe2f0954b08566b4efb53 upstream.

The well-spotted fallocate undo fix is good in most cases, but not when
fallocate failed on the very first page.  index 0 then passes lend -1
to shmem_undo_range(), and that has two bad effects: (a) that it will
undo every fallocation throughout the file, unrestricted by the current
range; but more importantly (b) it can cause the undo to hang, because
lend -1 is treated as truncation, which makes it keep on retrying until
every page has gone, but those already fully instantiated will never go
away.  Big thank you to xfstests generic/269 which demonstrates this.

Fixes: b9b4bb26af01 ("tmpfs: don't undo fallocate past its last page")
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tmpfs: don't undo fallocate past its last page

commit b9b4bb26af017dbe930cd4df7f9b2fc3a0497bfe upstream.

When fallocate is interrupted it will undo a range that extends one byte
past its range of allocated pages.  This can corrupt an in-use page by
zeroing out its first byte.  Instead, undo using the inclusive byte
range.

Fixes: 1635f6a74152f1d ("tmpfs: undo fallocation on failure")
Link: http://lkml.kernel.org/r/1462713387-16724-1-git-send-email-anthony.romano@coreos.com
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Brandon Philips <brandon@ifup.co>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

crypto: qat - make qat_asym_algs.o depend on asn1 headers

commit 81dc0365cfa7bc7c08a0e44d9ee04964df782e19 upstream.

Parallel build can sporadically fail because asn1 headers may
not be built yet by the time qat_asym_algs.o is compiled:
  drivers/crypto/qat/qat_common/qat_asym_algs.c:55:32: fatal error: qat_rsapubkey-asn1.h: No such file or directory
   #include "qat_rsapubkey-asn1.h"

Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/acpi: allow xen-acpi-processor driver to load on Xen 4.7

commit 6f2d9d99213514360034c6d52d2c3919290b3504 upstream.

As of Xen 4.7 PV CPUID doesn't expose either of CPUID[1].ECX[7] and
CPUID[0x80000007].EDX[7] anymore, causing the driver to fail to load on
both Intel and AMD systems. Doing any kind of hardware capability
checks in the driver as a prerequisite was wrong anyway: With the
hypervisor being in charge, all such checking should be done by it. If
ACPI data gets uploaded despite some missing capability, the hypervisor
is free to ignore part or all of that data.

Ditch the entire check_prereq() function, and do the only valid check
(xen_initial_domain()) in the caller in its place.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

File names with trailing period or space need special case conversion

commit 45e8a2583d97ca758a55c608f78c4cef562644d1 upstream.

POSIX allows files with trailing spaces or a trailing period but
SMB3 does not, so convert these using the normal Services For Mac
mapping as we do for other reserved characters such as
: < > | ? *
This is similar to what Macs do for the same problem over SMB3.

Signed-off-by: Steve French <steve.french@primarydata.com>
Acked-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: dynamic allocation of ntlmssp blob

commit b8da344b74c822e966c6d19d6b2321efe82c5d97 upstream.

In sess_auth_rawntlmssp_authenticate(), the ntlmssp blob is allocated
statically and its size is an "empirical" 5*sizeof(struct
_AUTHENTICATE_MESSAGE) (320B on x86_64). I don't know where this value
comes from or if it was ever appropriate, but it is currently
insufficient: the user and domain name in UTF16 could take 1kB by
themselves. Because of that, build_ntlmssp_auth_blob() might corrupt
memory (out-of-bounds write). The size of ntlmssp_blob in
SMB2_sess_setup() is too small too (sizeof(struct _NEGOTIATE_MESSAGE)
+ 500).

This patch allocates the blob dynamically in
build_ntlmssp_auth_blob().

Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix reconnect to not defer smb3 session reconnect long after socket reconnect

commit 4fcd1813e6404dd4420c7d12fb483f9320f0bf93 upstream.

Azure server blocks clients that open a socket and don't do anything on it.
In our reconnect scenarios, we can reconnect the tcp session and
detect the socket is available but we defer the negprot and SMB3 session
setup and tree connect reconnection until the next i/o is requested, but
this looks suspicous to some servers who expect SMB3 negprog and session
setup soon after a socket is created.

In the echo thread, reconnect SMB3 sessions and tree connections
that are disconnected.  A later patch will replay persistent (and
resilient) handle opens.

Signed-off-by: Steve French <steve.french@primarydata.com>
Acked-by: Pavel Shilovsky <pshilovsky@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

53c700: fix BUG on untagged commands

commit 8beb330044d0d1878c7b92290e91c0b889e92633 upstream.

The untagged command case in the 53c700 driver has been broken since
host wide tags were enabled because the replaced scsi_find_tag()
function had a special case for the tag value SCSI_NO_TAG to retrieve
sdev->current_cmnd.  The replacement function scsi_host_find_tag() has
no such special case and returns NULL causing untagged commands to
trigger a BUG() in the driver.  Inspection shows that the 53c700 is the
only driver using this SCSI_NO_TAG case, so a local fix in the driver
suffices to fix this problem globally.

Fixes: 64d513ac31b - "scsi: use host wide tags by default"
Reported-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390: fix test_fp_ctl inline assembly contraints

commit bcf4dd5f9ee096bd1510f838dd4750c35df4e38b upstream.

The test_fp_ctl function is used to test if a given value is a valid
floating-point control. The inline assembly in test_fp_ctl uses an
incorrect constraint for the 'orig_fpc' variable. If the compiler
chooses the same register for 'fpc' and 'orig_fpc' the test_fp_ctl()
function always returns true. This allows user space to trigger
kernel oopses with invalid floating-point control values on the
signal stack.

This problem has been introduced with git commit 4725c86055f5bbdcdf
"s390: fix save and restore of the floating-point-control register"

Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: fix race between simultaneous decrements of ->host_failed

commit 72d8c36ec364c82bf1bf0c64dfa1041cfaf139f7 upstream.

sas_ata_strategy_handler() adds the works of the ata error handler to
system_unbound_wq. This workqueue asynchronously runs work items, so the
ata error handler will be performed concurrently on different CPUs. In
this case, ->host_failed will be decreased simultaneously in
scsi_eh_finish_cmd() on different CPUs, and become abnormal.

It will lead to permanently inequality between ->host_failed and
->host_busy, and scsi error handler thread won't start running. IO
errors after that won't be handled.

Since all scmds must have been handled in the strategy handler, just
remove the decrement in scsi_eh_finish_cmd() and zero ->host_busy after
the strategy handler to fix this race.

Fixes: 50824d6c5657 ("[SCSI] libsas: async ata-eh")
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: verify upper dentry in ovl_remove_and_whiteout()

commit cfc9fde0b07c3b44b570057c5f93dda59dca1c94 upstream.

The upper dentry may become stale before we call ovl_lock_rename_workdir.
For example, someone could (mistakenly or maliciously) manually unlink(2)
it directly from upperdir.

To ensure it is not stale, let's lookup it after ovl_lock_rename_workdir
and and check if it matches the upper dentry.

Essentially, it is the same problem and similar solution as in
commit 11f3710417d0 ("ovl: verify upper dentry before unlink and rename").

Signed-off-by: Maxim Patlasov <mpatlasov@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ovl: Copy up underlying inode's ->i_mode to overlay inode

commit 07a2daab49c549a37b5b744cbebb6e3f445f12bc upstream.

Right now when a new overlay inode is created, we initialize overlay
inode's ->i_mode from underlying inode ->i_mode but we retain only
file type bits (S_IFMT) and discard permission bits.

This patch changes it and retains permission bits too. This should allow
overlay to do permission checks on overlay inode itself in task context.

[SzM] It also fixes clearing suid/sgid bits on write.

Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Reported-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 4bacc9c9234c ("overlayfs: Make f_path always point to the overlay and f_inode to the underlay")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: mvebu: fix HW I/O coherency related deadlocks

commit c5379ba8fccd99d5f99632c789f0393d84a57805 upstream.

Until now, our understanding for HW I/O coherency to work on the
Cortex-A9 based Marvell SoC was that only the PCIe regions should be
mapped strongly-ordered. However, we were still encountering some
deadlocks, especially when testing the CESA crypto engine. After
checking with the HW designers, it was concluded that all the MMIO
registers should be mapped as strongly ordered for the HW I/O coherency
mechanism to work properly.

This fixes some easy to reproduce deadlocks with the CESA crypto engine
driver (dmcrypt on a sufficiently large disk partition).

Tested-by: Terry Stockert <stockert@inkblotadmirer.me>
Tested-by: Romain Perier <romain.perier@free-electrons.com>
Cc: Terry Stockert <stockert@inkblotadmirer.me>
Cc: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: armada-38x: fix MBUS_ID for crypto SRAM on Armada 385 Linksys

commit 929e604efa3dc0522214e0dc18984be23993e9f0 upstream.

When the support for the Marvell crypto engine was added in the Device
Tree of the various Armada 385 Device Tree files in commit
d716f2e837ac6 ("ARM: mvebu: define crypto SRAM ranges for all armada-38x
boards"), a typo was made in the MBus window attributes for the Armada
385 Linksys board: 0x09/0x05 are used instead of 0x19/0x15. This commit
fixes this typo, which makes the CESA engines operational on Armada 385
Linksys boards.

Reported-by: Terry Stockert <stockert@inkblotadmirer.me>
Cc: Terry Stockert <stockert@inkblotadmirer.me>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d716f2e837ac6 ("ARM: mvebu: define crypto SRAM ranges for all armada-38x boards")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: sunxi/dt: make the CHIP inherit from allwinner,sun5i-a13

commit 5fc39d347267bd029fcc9099c70e2fe2d53130e9 upstream.

The sun4i-timer driver registers its sched_clock only if the machine is
compatible with "allwinner,sun5i-a13", "allwinner,sun5i-a10s" or
"allwinner,sun4i-a10".
Add the missing "allwinner,sun5i-a13" string to the machine compatible.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 465a225fb2af ("ARM: sun5i: Add C.H.I.P DTS")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>