OSDN Git Service
Olof Johansson [Thu, 26 Jul 2018 06:39:59 +0000 (23:39 -0700)]
Merge tag 'qcom-arm64-for-4.19' of git://git./linux/kernel/git/agross/linux into next/dt
Qualcomm ARM64 Updates for v4.19
* Add support for PM8005/PM8998 and related nodes
* Add/fix nodes on SDM845 for I2c, SPI, UART, and RPMH
* Fix BT LED trigger on DB410c
* Drop legacy clock names on MSM8916
* Add gpio line names on DB820c
* tag 'qcom-arm64-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: qcom: db410c: Fix Bluetooth LED trigger
arm64: dts: sdm845: Default qupv3_id_0 as "disabled" like _id_1
arm64: dts: msm8916: drop legacy suffix for clocks used by MSM DRM driver
arm64: dts: qcom: db820c: Add gpio-line-names property
arm64: dts: sdm845: Add rpmh-clk node
arm64: dts: sdm845: Add rpmh-rsc node
arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp
arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes
arm64: dts: qcom: Add pm8005 and pm8998 support
arm64: dts: qcom: Add pmu node to sdm845
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 22:06:03 +0000 (15:06 -0700)]
Merge tag 'am654-for-v4.19-signed' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
TI AM654 support for v4.19 merge window
This branch adds initial support for new Texas Instruments AM654
quad core A53 ARMv8 SoC. It's the first device for TI K3 multicore SoC
architecture.
Initially only basic devices are configured, support for more devices
will follow later on. And many of the internal devices familiar from
earlier TI SoCs should work with existing kernel device drivers.
* tag 'am654-for-v4.19-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm64: dts: ti: Add support for AM654 EVM base board
soc: ti: Add Support for AM654 SoC config option
arm64: dts: ti: Add Support for AM654 SoC
arm64: Add support for TI's K3 Multicore SoC architecture
dt-bindings: arm: ti: Add bindings for AM654 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:56:39 +0000 (14:56 -0700)]
Merge tag 'imx-dt64-4.19' of git://git./linux/kernel/git/shawnguo/linux into next/dt
Freescale arm64 device tree update for 4.19:
- Update device tree sources to use SPDX identifiers for license.
- Add cooling device property '#cooling-cells' for all CPUs of
a cluster.
* tag 'imx-dt64-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: freescale: Add missing cooling device properties for CPUs
arm64: dts: freescale: Update to use SPDX identifiers
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:55:45 +0000 (14:55 -0700)]
Merge tag 'imx-dt-4.19' of git://git./linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree update for 4.19:
- Add device tree support for i.MX6SLL SoC.
- New board support: ConnectCore 6UL System-On-Module and SBC Express;
ZII SCU2 Mezz, SCU3 ESB, SSMB SPU3 and CFU1 board; i.MX6SLL EVK
board; Engicam i.CoreM6 1.5 Quad/Dual MIPI; LogicPD MX31Lite board;
i.MX53 HSC/DDC boards from K+P.
- Remove fake regulator bus container node and enable USB OTG support
for i.MX6 wandboard and riotboard.
- Populate RAVE SP EEPROM, backlight, power button and watchdog devices
for ZII boards.
- Add cooling-cells for cpufreq cooling device, and add OPP properties
for all CPUs.
- A series from Anson Huang to enable LCD panel and backlight support
for imx6sll-evk board.
- Make pfuze100 sw4 regulator always-on for for a few Freescale/NXP
development boards, because the regulator is critical there and
cannot be turned off.
- Add more device support for i.MX5: AIPSTZ, SAHARA Crypto, M4IF,
Tigerp, PMU, CodaHx4 VPU.
- Enable PMU secure-reg-access for imx51-babbage, imx51-zii-rdu1 and
imx53-ppd board.
- Switch more device tree license to use SPDX identifier.
- Switch to use OF graph to describe the display for imx7d-nitrogen7.
- Add chosen/stdout-path for more boards, so that earlycon can be
enabled more easily on kernel cmdline.
- Convert GPC to new device tree bindings and add Vivante gpu nodes
for i.MX6SL SoC.
- Add more device support for imx6dl-mamoj board: parallel display,
WiFi and USB.
- A series from Stefan Agner to update i.MX6 apalis/colibri boards on
various aspects: SD/MMC card detection, regulators, etc.
* tag 'imx-dt-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (96 commits)
ARM: dts: imx7d: remove "operating-points" property for cpu1
ARM: dts: vf610-zii-ssmb-spu3: Fix W=1 level warnings
ARM: dts: vf610: Add ZII CFU1 board
ARM: dts: imx6dl-mamoj: Add usb host and device support
ARM: dts: imx6dl-mamoj: Add Wifi support
ARM: dts: imx6dl-mamoj: Add parallel display support
ARM: dts: vf610: Add ZII SSMB SPU3 board
ARM: dts: imx6ul-pico-hobbit: Do not hardcode the memory size
ARM: dts: imx6sl-evk: make pfuze100 sw4 always on
ARM: dts: imx6sll-evk: make pfuze100 sw4 always on
ARM: dts: imx6sx-sdb-reva: make pfuze100 sw4 always on
ARM: dts: imx6qdl-sabresd: make pfuze100 sw4 always on
ARM: dts: imx6sl-evk: add missing GPIO iomux setting
ARM: dts: imx51-zii-scu3-esb: Fix RAVE SP watchdog compatible string
ARM: dts: imx51-zii-scu3-esb: Add switch IRQ line pinumx config
ARM: dts: imx6sx-nitrogen6sx: remove obsolete display configuration
ARM: dts: imx7d-nitrogen7: use OF graph to describe the display
ARM: dts: imx: Switch Boundary Devices boards to SPDX identifier
ARM: dts: imx6sl: Add vivante gpu nodes
ARM: dts: imx6sll-evk: enable SEIKO 43WVF1G lcdif panel
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:54:42 +0000 (14:54 -0700)]
Merge tag 'imx-dt-clkdep-4.19' of git://git./linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree changes with clock dependency:
- Add clock for i.MX6UL GPIO blocks
* tag 'imx-dt-clkdep-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6ul: add GPIO clocks
clk: imx6ul: remove clks_init_on array
clk: imx6ul: add GPIO clock gates
dt-bindings: clock: imx6ul: Do not change the clock definition order
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:49:25 +0000 (14:49 -0700)]
Merge tag 'amlogic-dt64-1' of https://git./linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 64-bit DT updates for v4.19
- new SoC: S805x
- new board: S805x-based P241 board from Amlogic
- AXG: add ADC support w/buttons, add pins for PDM, SPDIF
- AXG: s400 board: preliminary support for audio
- GX: nanopi-k2: add HDMI, CEC, CVBS support
* tag 'amlogic-dt64-1' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-axg: add pdm pins
ARM64: dts: meson-axg: add spdif input pins
ARM64: dts: meson-axg: remove spdif out from gpio a7
ARM64: dts: meson-axg: add adc buttons the S400
ARM64: dts: meson-axg: remove vddio_ao18 from SoC dtsi
ARM64: dts: meson-axg: add saradc support
ARM64: dts: add S805X based P241 board
dt-bindings: amlogic: Add support for GXL S805X and the P241 board
ARM64: dts: amlogic: Add missing cooling device properties for CPUs
ARM64: dts: meson-axg: add spdif output pins
ARM64: dts: meson-axg: add s400 speaker amplifier
ARM64: dts: meson-axg: add s400 main 12v supply
ARM64: dts: meson-axg: add s400 microphone card leds
ARM64: dts: meson-gxbb-nanopi-k2: Add HDMI, CEC and CVBS nodes
ARM64: dts: meson-gx-p23x-q20x: move the wifi node to each board's .dts
ARM64: dts: meson: enable the saradc node in meson-gx-p23x-q20x.dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:48:09 +0000 (14:48 -0700)]
Merge tag 'renesas-dt-bindings-for-v4.19' of https://git./linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Bindings Updates for v4.19
Bindings relating to initial support for RZ/N1D (R9A06G032) SoC and its
RZN1D-DB board:
* Add Renesas R9A06G032 SMP enable method
* Document SoC and Board bindings
* tag 'renesas-dt-bindings-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
dt-bindings: cpu: Add Renesas R9A06G032 SMP enable method.
dt-bindings: arm: Document the RZN1D-DB board
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:35:40 +0000 (14:35 -0700)]
Merge tag 'renesas-arm64-dt2-for-v4.19' of https://git./linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM64 Based SoC DT Updates for v4.19
Corrections:
* Remove non-existing STBE region from Ether-AVB node in DT of
R-Car E3 (r8a77990) SoC
Cleanups:
* Consistently use rwdt as label for Renesas Watchdog Timer devices
* Add second port to rcar_sound placeholder in DT of R-Car M3-N (r8a77965) SoC
* Fix adv7482 decimal unit addresses in DT of Salvator-X and -XS boards
Enhancements:
* Describe in DT:
- INTC-EX of R-Car V3H (r8a77980) SoC
- USB3.0 of R-Car E3 (r8a77980) SoC
- All SCIF and HSCIF devices of R-Car D3 (r8a77995) SoC.
Previously only SCIF2, used as the debug consile, was described.
- All IPMMU devicesof R-Car M3-N (r8a77965), V3H (r8a77980) and
E3 (r8a77990) SoCs
* Enable USB3.0 in DT of R-Car E3 (r8a77980) based Ebisu board
* Prefer HSCIF1 over SCIF1 in DT of Salvator-X and -XS boards
* tag 'renesas-arm64-dt2-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a77980: add INTC-EX support
arm64: dts: renesas: r8a77990: Enable USB3.0 host for Ebisu board
arm64: dts: renesas: r8a77995: Add SCIF {0,1,3,4,5} and all HSCIF device nodes
arm64: dts: renesas: r8a779{65,80,90}: Add IPMMU devices nodes
arm64: dts: renesas: Unify the labels for RWDT
arm64: dts: renesas: salvator-common: Prefer HSCIF1 over SCIF1
arm64: dts: renesas: r8a77965: Add second port to rcar_sound placeholder
arm64: dts: renesas: salvator-common: Fix adv7482 decimal unit addresses
arm64: dts: renesas: r8a77990: Remove non-existing STBE region
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:30:08 +0000 (14:30 -0700)]
Merge tag 'at91-ab-4.19-dt' of git://git./linux/kernel/git/abelloni/linux into next/dt
AT91 DT for 4.19:
- New boards from Laird: WB45N, WB50N, SOM60 modules and DVK, Gatwick
- fix the PMC compatibles
* tag 'at91-ab-4.19-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: fix typos for SSC TD functions
ARM: dts: add support for Laird SOM60 module and DVK boards
ARM: dts: add support for Gatwick board based on WB50N
ARM: dts: add support for Laird WB50N cpu module and DVK
ARM: dts: add support for Laird WB45N cpu module and DVK
ARM: dts: at91: add labels to soc dtsi for derivative boards
dt-bindings: add laird and giantec vendor prefix
ARM: dts: fix PMC compatible
ARM: at91: fix USB clock detection handling
dt-bindings: clk: at91: Document all the PMC compatibles
dt-bindings: arm: remove PMC bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Viresh Kumar [Fri, 20 Jul 2018 10:11:50 +0000 (18:11 +0800)]
ARM: dts: berlin: Add missing OPP properties for CPUs
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (clocks, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:28:31 +0000 (14:28 -0700)]
Merge tag 'hisi-arm64-dt-for-4.19v2' of git://github.com/hisilicon/linux-hisi into next/dt
ARM64: DT: Hisilicon SoC DT updates for 4.19v2
- Tidy up MMC properties for hi3660
- Remove keep-power-in-suspend on hikey and hikey960 to
avoid keeping wifi power during suspend and let the
user enable it if required
- Update idle states for hikey960
- Add missing cooling device properties for cpus on hi6220
* tag 'hisi-arm64-dt-for-4.19v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Add missing cooling device properties for CPUs
arm64: hikey960: update idle-states
arm64: dts: hikey: Remove keep-power-in-suspend property
arm64: dts: hikey960: Remove keep-power-in-suspend property
arm64: dts: hikey960: Clean up MMC properties and move to proper file
arm64: dts: hikey960: Remove deprecated MMC properties
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:27:56 +0000 (14:27 -0700)]
Merge tag 'zynq-dt-for-v4.19-v2' of https://github.com/Xilinx/linux-xlnx into next/dt
ARM: dts: zynq: DT changes for v4.19
- Add Z-turn board
- Add mmc aliases
- Fix model information
- Sort out documentatio
- Update Zybo Z7
- Fix gpio-keys
* tag 'zynq-dt-for-v4.19-v2' of https://github.com/Xilinx/linux-xlnx:
ARM: dts: zynq: Remove #address/#size-cells from gpio-keys
ARM: dts: zynq: Add LEDs to the Zybo Z7 board
ARM: dts: zynq: Use gpio constants for the Zybo Z7 board
ARM: dts: zynq: Fix memory size on the Zybo Z7 board
dt-bindings: xilinx: zynq: Add missing boards
dt-bindings: xilinx: zynq: Move Paralella board to Xilinx
dt-bindings: xilinx: zynq: Sort entries alphabetically
dt-bindings: xilinx: zynq: Improve boards description
ARM: dts: zynq: correct and improve the model property of dt files
ARM: dts: zynq: Set correct manufacturer for ZedBoard and MicroZed boards
ARM: dts: zynq: Add mmc alias for zc702/zc706/zed/zybo
ARM: dts: zynq: Add support for Z-turn board
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:27:26 +0000 (14:27 -0700)]
Merge tag 'zynqmp-dt-for-v4.19-v2' of https://github.com/Xilinx/linux-xlnx into next/dt
arm: dts: zynqmp: DT changes for v4.19
- Use serdev for BT in zcu100
- Remove ep108
- Fix gpio-keys binding
- Add suport for Ultra96
* tag 'zynqmp-dt-for-v4.19-v2' of https://github.com/Xilinx/linux-xlnx:
arm64: dts: zynqmp: Add support for Avnet Ultra96 rev1 board
arm64: dts: zynqmp: Remove #address/#size-cells from gpio-keys
arm64: dts: zynqmp: Remove ep108 board
arm64: dts: zynqmp: Use serdev for zcu100 BT
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:26:49 +0000 (14:26 -0700)]
Merge tag 'uniphier-dt64-v4.19' of git://git./linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM64 SoC DT updates for v4.19
- Add missing #cooling-cells properties
- Add hp-det-gpio property to detect headphone via GPIO
* tag 'uniphier-dt64-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: add headphone detect gpio for LD11 global board
arm64: dts: uniphier: add headphone detect gpio for LD20 global board
arm64: dts: uniphier: Add missing cooling device properties for CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:26:15 +0000 (14:26 -0700)]
Merge tag 'uniphier-dt-v4.19' of git://git./linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM SoC DT updates for v4.19
- Add missing #cooling-cells properties
* tag 'uniphier-dt-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: Add missing cooling device properties for CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 21 Jul 2018 21:25:39 +0000 (14:25 -0700)]
Merge tag 'omap-for-v4.19/dt-pt2-signed' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
Few more beaglebone variants for v4.19 merge window
This adds dts files for two new beaglebone variants for
Octavo Systems OSD3358-SM-RED and Sancloud am335x-sancloud-bbe.
* tag 'omap-for-v4.19/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x: add am335x-sancloud-bbe board support
dt-bindings: Add vendor prefix for Sancloud
ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED based on TI AM335x
Signed-off-by: Olof Johansson <olof@lixom.net>
Loic Poulain [Wed, 11 Jul 2018 12:18:23 +0000 (14:18 +0200)]
arm64: dts: qcom: db410c: Fix Bluetooth LED trigger
Current LED trigger, 'bt', is not known/used by any existing driver.
Fix this by renaming it to 'bluetooth-power' trigger which is
controlled by the Bluetooth subsystem.
Fixes:
9943230c8860 ("arm64: dts: qcom: Add apq8016-sbc board LED's related device nodes")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Douglas Anderson [Fri, 29 Jun 2018 18:45:27 +0000 (11:45 -0700)]
arm64: dts: sdm845: Default qupv3_id_0 as "disabled" like _id_1
In commit
8e4947ee477d ("arm64: dts: qcom: sdm845: Add I2C, SPI, and
UART9 nodes") I accidentally forgot to add the line:
status = "disabled";
to qupv3_id_0 to match qupv3_id_1. Add it now. NOTE: right now the
only sdm845 board with a device tree in mainline is MTP and that board
currently doesn't have any peripherals under qupv3_id_0. If any board
was currently using peripherals under qupv3_id_0 then that board would
need to add this snippet to their board dts file:
&qupv3_id_0 {
status = "okay";
};
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Niklas Cassel [Thu, 19 Jul 2018 11:12:34 +0000 (13:12 +0200)]
arm64: dts: msm8916: drop legacy suffix for clocks used by MSM DRM driver
Drop legacy suffix for clocks used by MSM DRM driver.
The _clk suffix has been deprecated since commit
20c3bb80235 ("drm/msm:
drop _clk suffix from clk names").
Fixes:
720c3bb80235 (drm/msm: drop _clk suffix from clk names)
The following warnings during boot have been seen since the referenced
fixes commit:
msm_dsi_phy
1a98300.dsi-phy: Using legacy clk name binding. Use "iface" instead of "iface_clk"
msm
1a00000.mdss: Using legacy clk name binding. Use "iface" instead of "iface_clk"
msm
1a00000.mdss: Using legacy clk name binding. Use "bus" instead of "bus_clk"
msm
1a00000.mdss: Using legacy clk name binding. Use "vsync" instead of "vsync_clk"
msm_mdp
1a01000.mdp: Using legacy clk name binding. Use "bus" instead of "bus_clk"
msm_mdp
1a01000.mdp: Using legacy clk name binding. Use "iface" instead of "iface_clk"
msm_mdp
1a01000.mdp: Using legacy clk name binding. Use "core" instead of "core_clk"
msm_mdp
1a01000.mdp: Using legacy clk name binding. Use "vsync" instead of "vsync_clk"
msm_dsi
1a98000.dsi: Using legacy clk name binding. Use "mdp_core" instead of "mdp_core_clk"
msm_dsi
1a98000.dsi: Using legacy clk name binding. Use "iface" instead of "iface_clk"
msm_dsi
1a98000.dsi: Using legacy clk name binding. Use "bus" instead of "bus_clk"
msm_dsi
1a98000.dsi: Using legacy clk name binding. Use "byte" instead of "byte_clk"
msm_dsi
1a98000.dsi: Using legacy clk name binding. Use "pixel" instead of "pixel_clk"
msm_dsi
1a98000.dsi: Using legacy clk name binding. Use "core" instead of "core_clk"
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Manivannan Sadhasivam [Wed, 18 Apr 2018 13:46:01 +0000 (19:16 +0530)]
arm64: dts: qcom: db820c: Add gpio-line-names property
Add gpio-line-names property for Dragonboard820c based on APQ8096 SoC.
There are 4 gpio-controllers present on this board, including the
APQ8096 SoC, PM8994 (GPIO and MPP) and PMI8994 (GPIO).
Lines names are derived from 96Boards CE Specification 1.0, Appendix
"Expansion Connector Signal Description". Line names for PMI8994 MPP
pins are not added due to the absence of the gpio-controller support.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Douglas Anderson [Mon, 18 Jun 2018 21:50:51 +0000 (14:50 -0700)]
arm64: dts: sdm845: Add rpmh-clk node
This adds the rpmh-clk node to sdm845 based on the examples in the
bindings.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Douglas Anderson [Mon, 18 Jun 2018 21:50:50 +0000 (14:50 -0700)]
arm64: dts: sdm845: Add rpmh-rsc node
This adds the rpmh-rsc node to sdm845 based on the examples in the
bindings.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Douglas Anderson [Wed, 13 Jun 2018 16:53:52 +0000 (09:53 -0700)]
arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp
The debug UART is very useful to have. I2C10 is enabled as an example
of a I2C port we can talk on for now. Eventually we'll want to put
peripherals under it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Douglas Anderson [Wed, 13 Jun 2018 16:53:51 +0000 (09:53 -0700)]
arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes
This adds nodes to SDM845-dtsi for all the I2C ports, all the SPI
ports, and UART9. Note that I2C / SPI / UART are a bit strange on
sdm845 because each "serial engine" has 4 pins associated with it and
depending on which firmware has been loaded into the serial engine
(loaded by the BIOS) the serial engine can behave like an I2C port, a
SPI port, or a UART. As per the landed bindings that means that we
need to create one node for each possible mode that the port could be
in. With 16 serial engines that means 16 x 3 = 48 nodes.
We get away with only creating 33 nodes for now because it seems very
likely that SDM845-based boards will actually all use the same UART
(UART 9) for debug purposes. While another UART could be used for
something like Bluetooth communication we can cross that path when we
come to it. Some documentation that I saw implied that using a UART
for "high speed" communications actually needs yet another different
serial engine firmware anyway.
Note that quick measurements adding all these nodes adds <10k of extra
space per dtb that they're included with. If this becomes a problem
we may need to think of a different way to structure this so that
boards only get the nodes they need (or figure out how to get dtc to
strip 'disabled' nodes). For now it seems OK.
These nodes were programmatically generated with a fairly dumb python
script. See http://crosreview.com/
1091631 for the source.
NOTE: at the moment SPI chip select doesn't appear to work in my tests
with the latest posted SPI driver. All testing of SPI with this patch
has been done by hacking SPI to GPIO chip select.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Stephen Boyd [Wed, 13 Jun 2018 15:20:54 +0000 (08:20 -0700)]
arm64: dts: qcom: Add pm8005 and pm8998 support
Add basic support for the pm8005 and pm8998 PMICs. For now just support
the GPIO controllers.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Stephen Boyd [Tue, 22 May 2018 06:23:52 +0000 (23:23 -0700)]
arm64: dts: qcom: Add pmu node to sdm845
Add the CPU PMU on sdm845 to get perf support for hardware events.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Anson Huang [Thu, 19 Jul 2018 08:24:19 +0000 (16:24 +0800)]
ARM: dts: imx7d: remove "operating-points" property for cpu1
Commit
b97872d4eb22 ("ARM: dts: imx: Add missing OPP properties for CPUs")
added "operating-points" property for all CPUs, but i.MX7D already has
"operating-points-v2" property on both CPUs, so no need to add
"operating-points" property again, this patch removes it.
Fixes:
b97872d4eb22 ("ARM: dts: imx: Add missing OPP properties for CPUs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Thu, 19 Jul 2018 20:00:02 +0000 (13:00 -0700)]
ARM: dts: vf610-zii-ssmb-spu3: Fix W=1 level warnings
Fix a couple of things that were causing warning when building DTB
with W=1.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: cphealy@gmail.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Thu, 19 Jul 2018 19:57:24 +0000 (12:57 -0700)]
ARM: dts: vf610: Add ZII CFU1 board
Add support for the Zodiac Inflight Innovations CFU1
board (VF610-based).
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jerome Brunet [Mon, 16 Jul 2018 10:11:50 +0000 (12:11 +0200)]
ARM64: dts: meson-axg: add pdm pins
Add pdm input pin definitions to meson AXG
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Jerome Brunet [Mon, 16 Jul 2018 10:11:49 +0000 (12:11 +0200)]
ARM64: dts: meson-axg: add spdif input pins
Add spdif input pin definitions to meson AXG
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Jerome Brunet [Mon, 16 Jul 2018 10:11:48 +0000 (12:11 +0200)]
ARM64: dts: meson-axg: remove spdif out from gpio a7
Spdif out in not multiplexed on gpio A7 (spdif in is)
Remove this entry to fix the problem.
Fixes:
53c03b0aff36 ("ARM64: dts: meson-axg: add spdif output pins")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Jerome Brunet [Mon, 16 Jul 2018 10:11:47 +0000 (12:11 +0200)]
ARM64: dts: meson-axg: add adc buttons the S400
Add the 6 adc buttons of the amlogic S400
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Jerome Brunet [Mon, 16 Jul 2018 10:11:46 +0000 (12:11 +0200)]
ARM64: dts: meson-axg: remove vddio_ao18 from SoC dtsi
Regulator should not be defined inside the SoC dtsi file.
vddio_ao18 is already defined in the S400 board dts anyway.
Fixes:
bb8a2ebd0498 ("ARM64: dts: meson-axg: add saradc support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Xingyu Chen [Mon, 2 Jul 2018 22:25:15 +0000 (22:25 +0000)]
ARM64: dts: meson-axg: add saradc support
Add the DT info for SAR ADC of the Amlogic's Meson-AXG SoC.
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Neil Armstrong [Thu, 5 Jul 2018 09:50:43 +0000 (11:50 +0200)]
ARM64: dts: add S805X based P241 board
The Amlogic P241 board is the Reference Design board for the S805X
variant of the Amlogic Meson GXL SoC family.
The P241 board has the following features :
- 1GiB DDR4 Memory
- HDMI Connector with CEC
- A/V jack with Stereo Audio and CVBS
- 10/100 Ethernet
- 2x USB2.0 Type-A
- On-board WiFi SDIO Module
- On-board eMMC storage
- Infraread Received
- Factory Reset button
- UART connector
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Neil Armstrong [Thu, 5 Jul 2018 09:50:42 +0000 (11:50 +0200)]
dt-bindings: amlogic: Add support for GXL S805X and the P241 board
The S805X is a variant of the Amlogic Meson GXL SoC family with the
following physical limitations :
- No SDCard interface
- No GPIOCLK pins
- No USB OTG ID pin (but Gadget feature can stil be forced)
- No 5V regulator
- Reduced ADC inputs (only ADC0 and ADC1)
- GPIODV_26, GPIOAO_3, GPIOAO_4, GPIOAO_5, GPIOAO_6, GPIOX_14,
GPIOX_15, GPIOH_3 are no more exposed on the package
Amlogic exposes the following SW limitations :
- HDMI max resolution should be 1080p60, VPU clock should be downgraded
- Video Decoding should be limited to 1080p60, VDEC clock should be downgraded
- CPU speed should be limited by SCPI OPP table to 1.2GHz
- DRAM interface is limited to DDR4 16bit up to 1GiB
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Viresh Kumar [Fri, 25 May 2018 05:40:01 +0000 (11:10 +0530)]
ARM64: dts: amlogic: Add missing cooling device properties for CPUs
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[khilman: s/arm64/ARM64/ in Subject]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Jerome Brunet [Wed, 4 Jul 2018 17:04:09 +0000 (19:04 +0200)]
ARM64: dts: meson-axg: add spdif output pins
Add the different pin configurations for the spdif output
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Jerome Brunet [Thu, 28 Jun 2018 09:50:54 +0000 (11:50 +0200)]
ARM64: dts: meson-axg: add s400 speaker amplifier
Add the first of the two tas5707 power amplifier present on the
speaker daughter board.
According to the schematics of the S400 v3, only I2SB_DIN3 and
I2SC_DOUT2 will be available to the speaker board.
9R83, 9R84 and 9R18 are not connected so no audio signal will be
provided to the second amplifier. There is no point in enabling it
even if it is visible on the i2c bus.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Jerome Brunet [Thu, 28 Jun 2018 09:50:53 +0000 (11:50 +0200)]
ARM64: dts: meson-axg: add s400 main 12v supply
Add a fixed regulator for the main 12v which is the main power supply
of the board.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Jerome Brunet [Thu, 28 Jun 2018 09:50:52 +0000 (11:50 +0200)]
ARM64: dts: meson-axg: add s400 microphone card leds
The microphone card connected to the s400 has 6 leds controlled
through an additional i2c gpio controller.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Neil Armstrong [Tue, 26 Jun 2018 07:40:55 +0000 (09:40 +0200)]
ARM64: dts: meson-gxbb-nanopi-k2: Add HDMI, CEC and CVBS nodes
The Amlogic Meson GXBB based Nanopi-K2 board has an HDMI connector
with CEC and CVBS available on the 40pin header.
This patch adds the nodes to enable HDMI, CEC and CVBS functionnalities.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Martin Blumenstingl [Sat, 23 Jun 2018 19:38:28 +0000 (21:38 +0200)]
ARM64: dts: meson-gx-p23x-q20x: move the wifi node to each board's .dts
meson-gx-p23x-q20x.dtsi is currently used by five boards:
- Amlogic P230 and P231 (which should be identical, apart from the
external RGMII PHY on P230 whereas P231 can only use the internal PHY)
- Amlogic Q200 (identical to P230 but with an S912 GXM SoC instead of a
GXL S905D SoC) and Q201 (identical to P231 but with an S912 GXM SoC
instead of a GXL S905D SoC)
- NEXBOX A1 (based on the S912 GXM SoC)
The Amlogic P230 board uses a Broadcom BCM4356 SDIO wifi chip. Since the
other Amlogic reference design boards are very similar it's safe to
assume that these also use a Broadcom based SDIO wifi chip (which is
also how it was configured in meson-gx-p23x-q20x.dtsi).
However, NEXBOX A1 comes with a "longsys LTM8830" SDIO wifi module,
which is based on the "Qualcomm Atheros QCA9377-3(QCA1023-0)" chipset.
Thus move the wifi node from meson-gx-p23x-q20x.dtsi to each of the
four Amlogic reference board's .dts files.
There are no devicetree bindings for the QCA9377 SDIO wifi module yet,
so nothing is added to meson-gxm-nexbox-a1.dts.
Fixes:
f51b454549b812 ("ARM64: dts: meson-gxm: Add support for the Nexbox A1")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Martin Blumenstingl [Sat, 23 Jun 2018 14:59:59 +0000 (16:59 +0200)]
ARM64: dts: meson: enable the saradc node in meson-gx-p23x-q20x.dtsi
meson-gxl-s905d-p230.dts and meson-gxm-q200.dts enable the saradc node
(and configure it's vref-supply "VDDIO_AO18") in their corresponding
.dts file.
Move both (the saradc node as well as the VDDIO_AO18 regulator) to
remove some duplicate code.
As a positive side-effect this enables the saradc also for the P231 (GXL
S905D) and Q201 (GXM S912) development boards which are similar to the
P230/Q200 boards (P231 and Q201 use the internal 100Mbit/s PHY, while
P230 and Q200 have an external RGMII PHY).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Sergei Shtylyov [Tue, 17 Jul 2018 20:08:27 +0000 (23:08 +0300)]
arm64: dts: renesas: r8a77980: add INTC-EX support
Describe the INTC-EX interrupt controller in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Yoshihiro Shimoda [Wed, 18 Jul 2018 04:54:14 +0000 (13:54 +0900)]
arm64: dts: renesas: r8a77990: Enable USB3.0 host for Ebisu board
This patch adds and USB3.0 host device node and enable it for
R-Car E3 Ebisu board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Takeshi Kihara [Tue, 17 Jul 2018 11:42:09 +0000 (13:42 +0200)]
arm64: dts: renesas: r8a77995: Add SCIF {0,1,3,4,5} and all HSCIF device nodes
This patch adds the device nodes for SCIF {0,1,3,4,5} and all HSCIF serial
ports, incl. clocks, power domain and DMAs.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Claudiu Beznea [Tue, 17 Jul 2018 14:03:53 +0000 (17:03 +0300)]
ARM: dts: at91: fix typos for SSC TD functions
Fix typo for TD function of pins PIN_PB22 and PIN_PC14
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ben Whitten [Fri, 15 Jun 2018 13:40:55 +0000 (14:40 +0100)]
ARM: dts: add support for Laird SOM60 module and DVK boards
This adds support for Lairds upcoming SOM module, featuring Marvell WiFi
and Bluetooth, 2Gb NAND / 1Gb LPDDR SDRAM, and an Atmel SAMA5D3 CPU.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ben Whitten [Fri, 15 Jun 2018 13:40:54 +0000 (14:40 +0100)]
ARM: dts: add support for Gatwick board based on WB50N
Add support for the LoRa gateway from Laird, the RG1xx.
This board houses the WB50NBT CPU module along with a Semtech SX1301 based
concentrator card.
https://www.lairdtech.com/products/rg1xx-lora-gateway
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ben Whitten [Fri, 15 Jun 2018 13:40:53 +0000 (14:40 +0100)]
ARM: dts: add support for Laird WB50N cpu module and DVK
This adds support for Lairds CPU module, featuring Atheros wifi, CSR
Bluetooth and, Atmel SAMA5D3 CPU.
https://www.lairdtech.com/products/wb50nbt-wi-fi-bluetooth-module
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ben Whitten [Fri, 15 Jun 2018 13:40:52 +0000 (14:40 +0100)]
ARM: dts: add support for Laird WB45N cpu module and DVK
This adds support for Lairds combo CPU module, featuring on board
Atheros wifi, CSR Bluetooth radio and, Atmel CPU.
https://www.lairdtech.com/products/wb45nbt
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ben Whitten [Fri, 15 Jun 2018 13:40:51 +0000 (14:40 +0100)]
ARM: dts: at91: add labels to soc dtsi for derivative boards
This adds labels to commonly used device-tree nodes so that derivative
boards can avoid ahb/apb hierarchy.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Michal Simek [Tue, 17 Jul 2018 14:53:32 +0000 (16:53 +0200)]
ARM: dts: zynq: Remove #address/#size-cells from gpio-keys
dts reports incorrect usage of these properties in gpio-keys node.
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary
The patch is removing these useless properties.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 05:50:48 +0000 (01:50 -0400)]
ARM: dts: zynq: Add LEDs to the Zybo Z7 board
Add an LED node, connected to the Processing System (PS)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 05:50:47 +0000 (01:50 -0400)]
ARM: dts: zynq: Use gpio constants for the Zybo Z7 board
Include GPIO dt-bindings and use GPIO_ACTIVE_* constants
to improve readability
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 05:50:46 +0000 (01:50 -0400)]
ARM: dts: zynq: Fix memory size on the Zybo Z7 board
According to the reference manual, the board has two Micron
MT41K256M16HA-125 DDR3L memory ICs, which have 512 MiB each
Tested on a ZYBO-Z7-20 board
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:24 +0000 (00:10 -0400)]
dt-bindings: xilinx: zynq: Add missing boards
The bindings were missing when the device-tree
files were added
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:23 +0000 (00:10 -0400)]
dt-bindings: xilinx: zynq: Move Paralella board to Xilinx
Move the Adapteva Parallela board to Xilinx dt-bindings,
as it's based on a Zynq SoC from Xilinx
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:22 +0000 (00:10 -0400)]
dt-bindings: xilinx: zynq: Sort entries alphabetically
Sort additional compatible strings (boards) alphabetically
by their manufacturer and model number
This will help when finding a board because they
will be grouped by their manufacturer
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:21 +0000 (00:10 -0400)]
dt-bindings: xilinx: zynq: Improve boards description
Change the description of some boards to make it similar
to the value of the model property from their respective
device-tree, using the format "<manufacturer> <model>"
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:20 +0000 (00:10 -0400)]
ARM: dts: zynq: correct and improve the model property of dt files
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:19 +0000 (00:10 -0400)]
ARM: dts: zynq: Set correct manufacturer for ZedBoard and MicroZed boards
Both boards are made by Avnet, Inc. So add an additional
value to the compatible property
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 7 Apr 2016 09:23:34 +0000 (11:23 +0200)]
ARM: dts: zynq: Add mmc alias for zc702/zc706/zed/zybo
Add missing mmc alias.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Anton Gerasimov [Wed, 28 Mar 2018 14:17:34 +0000 (16:17 +0200)]
ARM: dts: zynq: Add support for Z-turn board
Add a dts for MYIR Z-turn board and respective target in Makefile.
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 2 May 2018 11:14:35 +0000 (13:14 +0200)]
arm64: dts: zynqmp: Add support for Avnet Ultra96 rev1 board
Avnet Ultra96 rev1 board is commercialized Xilinx zcu100 revC/D
internal board. The patch is reusing zcu100 revC files but changing
model description and compatible strings which are used for example by
libmraa.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 2 May 2018 11:29:00 +0000 (13:29 +0200)]
arm64: dts: zynqmp: Remove #address/#size-cells from gpio-keys
dts reports incorrect usage of these properties in gpio-keys node.
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary
The patch is removing these useless properties.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 2 Mar 2018 07:45:16 +0000 (08:45 +0100)]
arm64: dts: zynqmp: Remove ep108 board
ZynqMP Emulation board is no longer tested and there is no reason to
keep maintaining it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 12 Mar 2018 15:12:33 +0000 (16:12 +0100)]
arm64: dts: zynqmp: Use serdev for zcu100 BT
Mainline started to use serdev interface for uart attached devices.
Change description to reflect it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michael Trimarchi [Tue, 17 Jul 2018 09:25:26 +0000 (14:55 +0530)]
ARM: dts: imx6dl-mamoj: Add usb host and device support
Add USB host and device support for BTicino i.MX6DL Mamoj board.
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Tue, 17 Jul 2018 09:25:25 +0000 (14:55 +0530)]
ARM: dts: imx6dl-mamoj: Add Wifi support
Add TI WL18XX Wifi for BTicino i.MX6DL board.
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jagan Teki [Tue, 17 Jul 2018 09:25:24 +0000 (14:55 +0530)]
ARM: dts: imx6dl-mamoj: Add parallel display support
This patch adds parallel display support for i.MX6DL Mamoj board
along with relevant backlight through pwm.
LCD power sequence is added by 'Michael Trimarchi'.
Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Tue, 17 Jul 2018 04:06:51 +0000 (21:06 -0700)]
ARM: dts: vf610: Add ZII SSMB SPU3 board
Add support for Zodiac Inflight Innovations SSMB SPU3
board (VF610-based).
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Katsuhiro Suzuki [Mon, 25 Jun 2018 03:45:05 +0000 (12:45 +0900)]
arm64: dts: uniphier: add headphone detect gpio for LD11 global board
This patch adds GPIO for headphone detection on LD11 global board.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Katsuhiro Suzuki [Mon, 25 Jun 2018 03:45:04 +0000 (12:45 +0900)]
arm64: dts: uniphier: add headphone detect gpio for LD20 global board
This patch adds GPIO for headphone detection on LD20 global board.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Viresh Kumar [Fri, 25 May 2018 05:40:06 +0000 (11:10 +0530)]
arm64: dts: uniphier: Add missing cooling device properties for CPUs
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Viresh Kumar [Fri, 25 May 2018 10:31:51 +0000 (16:01 +0530)]
ARM: dts: uniphier: Add missing cooling device properties for CPUs
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Nishanth Menon [Tue, 26 Jun 2018 16:26:15 +0000 (11:26 -0500)]
arm64: dts: ti: Add support for AM654 EVM base board
The EValuation Module(EVM) platform for AM654 consists of a
common Base board + one or more of daughter cards, which include:
a) "Personality Modules", which can be specific to a profile, such as
ICSSG enabled or Multi-media (including audio).
b) SERDES modules, which may be 2 lane PCIe or two port PCIe + USB2
c) Camera daughter card
d) various display panels
Among other options. There are two basic configurations defined which
include an "EVM" configuration and "IDK" (Industrial development kit)
which differ in the specific combination of daughter cards that are
used.
To simplify support, we choose to support just the base board as the
core device tree file and all daughter cards would be expected to be
device tree overlays.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Tue, 26 Jun 2018 16:26:14 +0000 (11:26 -0500)]
soc: ti: Add Support for AM654 SoC config option
Add option to build AM6 SoC specific components
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benjamin Fair <b-fair@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Tue, 26 Jun 2018 16:26:13 +0000 (11:26 -0500)]
arm64: dts: ti: Add Support for AM654 SoC
The AM654 SoC is a lead device of the K3 Multicore SoC architecture
platform, targeted for broad market and industrial control with aim to
meet the complex processing needs of modern embedded products.
Some highlights of this SoC are:
* Quad ARMv8 A53 cores split over two clusters
* GICv3 compliant GIC500
* Configurable L3 Cache and IO-coherent architecture
* Dual lock-step capable R5F uC for safety-critical applications
* High data throughput capable distributed DMA architecture under NAVSS
* Three Gigabit Industrial Communication Subsystems (ICSSG), each with dual
PRUs and dual RTUs
* Hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
* Centralized System Controller for Security, Power, and Resource
management.
* Dual ADCSS, eQEP/eCAP, eHRPWM, dual CAN-FD
* Flash subsystem with OSPI and Hyperbus interfaces
* Multimedia capability with CAL, DSS7-UL, SGX544, McASP
* Peripheral connectivity including USB3, PCIE, MMC/SD, GPMC, I2C, SPI,
GPIO
See AM65x Technical Reference Manual (SPRUID7, April 2018)
for further details: http://www.ti.com/lit/pdf/spruid7
NOTE:
1. AM654 is the first of the device variants, hence we introduce a
generic am65.dtsi.
2. We indicate the proper bus topology, the ranges are elaborated in
each bus segment instead of using the top level ranges to make sure
that peripherals in each segment use the address space accurately.
3. Peripherals in each bus segment is maintained in a separate dtsi
allowing for reuse in different bus segment representation from a
different core such as R5. This is also the reason for maintaining a
1-1 address map in the ranges.
4. Cache descriptions follow the ARM64 standard description.
Further tweaks may be necessary as we introduce more complex devices,
but can be introduced in context of the device introduction.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benjamin Fair <b-fair@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Tue, 26 Jun 2018 16:26:12 +0000 (11:26 -0500)]
arm64: Add support for TI's K3 Multicore SoC architecture
Add support for Texas Instrument's K3 Multicore SoC architecture
processors.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Tue, 26 Jun 2018 16:26:11 +0000 (11:26 -0500)]
dt-bindings: arm: ti: Add bindings for AM654 SoC
The AM654 SoC is a lead device of the K3 Multicore SoC architecture
platform, targeted for broad market and industrial control with aim to
meet the complex processing needs of modern embedded products.
Some highlights of this SoC are:
* Quad ARMv8 A53 cores split over two clusters
* GICv3 compliant GIC500
* Configurable L3 Cache and IO-coherent architecture
* Dual lock-step capable R5F uC for safety-critical applications
* High data throughput capable distributed DMA architecture under NAVSS
* Three Gigabit Industrial Communication Subsystems (ICSSG), each with dual
PRUs and dual RTUs
* Hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
* Centralized System Controller for Security, Power, and Resource
management.
* Dual ADCSS, eQEP/eCAP, eHRPWM, dual CAN-FD
* Flash subsystem with OSPI and Hyperbus interfaces
* Multimedia capability with CAL, DSS7-UL, SGX544, McASP
* Peripheral connectivity including USB3, PCIE, MMC/SD, GPMC, I2C, SPI,
GPIO
See AM65x Technical Reference Manual (SPRUID7, April 2018)
for further details: http://www.ti.com/lit/pdf/spruid7
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Viresh Kumar [Fri, 25 May 2018 05:40:03 +0000 (11:10 +0530)]
arm64: dts: hisilicon: Add missing cooling device properties for CPUs
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Do minor rearrangement as well to keep ordering consistent.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Vincent Guittot [Wed, 11 Jul 2018 08:34:46 +0000 (10:34 +0200)]
arm64: hikey960: update idle-states
Update entry/exit latency and residency time of hikey960 to use more
realistic figures based on unitary tests done on the platform.
The complete results (in us) :
big cluster
cluster CPU
max entry latency 800 400
max exit latency 2900 550
residency 903Mhz 5000 1500
residency 2363Mhz 0 1500
little cluster
cluster CPU
max entry latency 500 400
max exit latency 1600 650
residency 533Mhz 8000 4500
residency 1844Mhz 0 1500
We can see that the residency time depends of the running OPP which is not
handled for now. Then we also have to take into account the constraint of
a residency time shorter than the tick to get full advantage of idle loop
reordering(tick is stopped if idle duration is higher than tick period).
Finally the selected residency value are :
big cluster
cluster CPU
residency 3700 1500
little cluster
cluster CPU
residency 3500 1500
A simple test with a task waking up every 11.111ms shows improvement:
- 5% a lowest OPP
- 22% at highest OPP
The period has been chosen:
- to be shorter than old cluster residency time and longer than new
residency time of cluster off C-state
- to prevent any sync with tick (4ms) when running tests that can add
some variances between tests
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
oscardagrach [Fri, 13 Jul 2018 16:02:31 +0000 (11:02 -0500)]
arm64: dts: hikey: Remove keep-power-in-suspend property
Remove the keep-power-in-suspend property because it keeps wifi power
on during suspend. This property is only required when enabling WoWLAN
and should only be enabled based on need.
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
oscardagrach [Fri, 13 Jul 2018 15:53:48 +0000 (10:53 -0500)]
arm64: dts: hikey960: Remove keep-power-in-suspend property
Remove the keep-power-in-suspend property because it keeps wifi power
on during suspend. This property is only required when enabling WoWLAN
and should only be enabled based on need. Also remove dupplicate property
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
oscardagrach [Mon, 18 Jun 2018 18:10:08 +0000 (13:10 -0500)]
arm64: dts: hikey960: Clean up MMC properties and move to proper file
Certain properties should be moved to the board file to reflect
the specific properties of the board, and not the SoC. Move these
properties to proper location and organize properties in both files.
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
oscardagrach [Mon, 18 Jun 2018 18:08:25 +0000 (13:08 -0500)]
arm64: dts: hikey960: Remove deprecated MMC properties
Remove deprecated MMC properties for hi3660
Signed-off-by: Ryan Grachek <ryan@edited.us>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Koen Kooi [Tue, 17 Jul 2018 06:51:49 +0000 (08:51 +0200)]
ARM: dts: am335x: add am335x-sancloud-bbe board support
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Tested on a revision G board.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Koen Kooi [Tue, 17 Jul 2018 07:40:58 +0000 (09:40 +0200)]
dt-bindings: Add vendor prefix for Sancloud
Add vendor prefix for Sancloud Ltd.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fabio Estevam [Tue, 17 Jul 2018 02:08:45 +0000 (23:08 -0300)]
ARM: dts: imx6ul-pico-hobbit: Do not hardcode the memory size
There are two variants of imx6ul-pico boards: one with 256MB and
another one with 512MB of RAM.
Do not hardcode the memory size in the device tree and let the
bootloader fill the correct value instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Robin Gong [Tue, 17 Jul 2018 05:12:05 +0000 (13:12 +0800)]
ARM: dts: imx6sl-evk: make pfuze100 sw4 always on
On i.MX6SL EVK board, pfuze100 sw4 supplies
LPDDR2 which is critical for system, must be
always on.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 17 Jul 2018 05:12:04 +0000 (13:12 +0800)]
ARM: dts: imx6sll-evk: make pfuze100 sw4 always on
On i.MX6SLL EVK board, pfuze100 sw4 supplies
LPDDR3 which is critical for system, must be
always on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 17 Jul 2018 05:12:03 +0000 (13:12 +0800)]
ARM: dts: imx6sx-sdb-reva: make pfuze100 sw4 always on
On i.MX6SX SDB Rev-A board, pfuze100 sw4 supplies
csi, audio codec and i2c etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 17 Jul 2018 05:12:02 +0000 (13:12 +0800)]
ARM: dts: imx6qdl-sabresd: make pfuze100 sw4 always on
On i.MX6QDL Sabre-SD board, pfuze100 sw4 supplies
GPS, touch and RGMII etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Neeraj Dantu [Fri, 13 Jul 2018 16:33:14 +0000 (16:33 +0000)]
ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED based on TI AM335x
OSD3358-SM-RED is a dev board for OSD335x System-in-Package(SiP) devices from
Octavo Systems.
This board family can be indentified by the A335BNLTOS00 in the at24 eeprom:
A2: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 4f 53 30 30 |.U3.A335BNLTOS00|]
https://octavosystems.com/octavo_products/osd3358-sm-red/
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Anson Huang [Sat, 14 Jul 2018 01:53:58 +0000 (09:53 +0800)]
ARM: dts: imx6sl-evk: add missing GPIO iomux setting
On i.MX6SL EVK board, the MX6SL_PAD_KEY_ROW5 pin is
used as lcd 3v3 regulator control pin, need to make
sure MX6SL_PAD_KEY_ROW5 is muxed as GPIO function
for controlling lcd 3v3 regulator.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by; Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Tue, 17 Jul 2018 06:44:38 +0000 (14:44 +0800)]
ARM: dts: imx51-zii-scu3-esb: Fix RAVE SP watchdog compatible string
It looks like I made a nasty typo in the original patch which resulted
in missing watchdog device. Fix it.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Andrey Smirnov [Fri, 13 Jul 2018 17:30:04 +0000 (10:30 -0700)]
ARM: dts: imx51-zii-scu3-esb: Add switch IRQ line pinumx config
Instead of relying on default values, configure PAD_AUD3_BB_CK to be a
GPIO explicitly. While at, it change the pad configuration to enable
a 100K pull-down (the pin is used as IRQ_TYPE_LEVEL_HIGH).
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>