OSDN Git Service
Mike Christie [Thu, 1 Sep 2011 02:53:40 +0000 (21:53 -0500)]
[SCSI] qla4xxx: select iscsi boot sysfs attrs
qla4xxx now uses iscsi_boot_sysfs to export the targets used
for boot to sysfs. It needs to select that config option
to make sure that module is also built.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Tue, 30 Aug 2011 22:54:54 +0000 (15:54 -0700)]
[SCSI] bnx2fc: Bumped version to 1.0.6
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Tue, 30 Aug 2011 22:54:53 +0000 (15:54 -0700)]
[SCSI] bnx2fc: Fix FW assert during RSCN stress tests
Firmware asserts when the same CQE is armed twice. This scenario happens during
RSCN stress tests as driver incorrects arms the CQ after the session is
offloaded.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Tue, 30 Aug 2011 22:54:52 +0000 (15:54 -0700)]
[SCSI] bnx2fc: Fix panic caused because of incorrect errror handling in create().
Driver incorrectly calls bnx2fc_interface_cleanup() when bnx2fc_if_create fails
which accesses bad pointer. Handle bnx2fc_if_create failure by directly calling
bnx2fc_net_cleanup.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Tue, 30 Aug 2011 22:54:51 +0000 (15:54 -0700)]
[SCSI] bnx2fc: Avoid calling bnx2fc_if_destroy with unnecessary locks
It is not required to hold rtnl_lock and bnx2fc_dev_lock when calling
bnx2fc_if_destroy, as the locking is only required to serialize creation and
deletion of fcoe instances. More importantly, this unnecessary locking causes
deadlock as bnx2fc_if_destroy calls fc_remove_host holding rtnl_lock.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Nithin Nayak Sujir [Tue, 30 Aug 2011 22:54:50 +0000 (15:54 -0700)]
[SCSI] bnx2fc: Validate vlan id in NETDEV_UNREGISTER handler
When bnx2fc receives an UNREGISTER event on a vlan interface it calls
destroy on all interfaces that matches the physical interface. Add
vlan_id check to destroy only the vlan interface that generated the
event.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Tue, 30 Aug 2011 22:54:49 +0000 (15:54 -0700)]
[SCSI] bnx2fc: No abort issued for REC when it times out
ABTS was not issued for timed out REC, as REC completion handler exits out if
the IO completed. Check for timed out REC and issue ABTS before proceeding with
further processing in REC completion handler. Also, initialize rec_retry and
srr_retry before starting the IO.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Tue, 30 Aug 2011 22:54:48 +0000 (15:54 -0700)]
[SCSI] bnx2fc: Send solicitation only after vlan discovery is complete
Link up event is generated to the driver even before vlan discovery has
started. Because of this driver can send discovery solicitation on a stale
vlan. Call fcoe_ctlr_link_up() only when the driver is in enabled state, which
implies the vlan discovery is complete before sending solicitation.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Tue, 30 Aug 2011 22:54:47 +0000 (15:54 -0700)]
[SCSI] bnx2fc: Reset max receive frame size during link up
If the max receive frame size is changed during link down, the driver uses the
same value after linkup unless it is reset to default.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Wed, 24 Aug 2011 08:51:19 +0000 (10:51 +0200)]
[SCSI] scsi_dh_alua: Decrease retry interval
The alua device handler starts the first retry after 10 seconds,
and increases it times 10 for each round.
This leads to an unnecessary delay. This patch modifies it to
start after one second, and increase by a factor of two.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Wed, 24 Aug 2011 08:51:18 +0000 (10:51 +0200)]
[SCSI] scsi_dh_alua: Fix Erroneous TPG ID check
For Target Portal Group IDs occupying the full 2 bytes in the
RTPG response, the following group_id check in the alua_rtpg
routine always fails in scsi_dh_alua.c:
if (h->group_id == (ucp[2] << 8) + ucp[3]) {
This causes the ALUA handler to wrongly identify the AAS of
a specified device as well as incorrectly interpreting the
supported AAS of the target as seen by the following entries
in the /var/log/messages:
"alua: port group 3ea state A supports tousna"
"alua: port group 3e9 state A supports tousna"
This is because 'ucp' is wrongly declared in alua_rtpg as
a character pointer instead of an unsigned character pointer.
Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Wed, 24 Aug 2011 08:51:17 +0000 (10:51 +0200)]
[SCSI] scsi_dh: Check for sdev state in store_dh_state()
Avoid attaching a hardware handler to a device which is
already scheduled for deletion.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Wed, 24 Aug 2011 08:51:16 +0000 (10:51 +0200)]
[SCSI] scsi_dh_alua: always update TPGS status on activate
When activating a patch we should always update the TPGS state
as it might have changed in between.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Wed, 24 Aug 2011 08:51:15 +0000 (10:51 +0200)]
[SCSI] scsi_dh: Implement match callback function
Some device handler types are not tied to the vendor/model
but rather to a specific capability. Eg ALUA is supported
if the 'TPGS' setting in the standard inquiry is set.
This patch implements a 'match' callback for device handler
which supersedes the original vendor/model lookup and
implements the callback for the ALUA handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Wed, 24 Aug 2011 08:51:14 +0000 (10:51 +0200)]
[SCSI] scsi_dh: Fixup kernel-doc comments
Fixup some kernel-doc comments to reference to the
correct function name.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Wed, 24 Aug 2011 08:51:13 +0000 (10:51 +0200)]
[SCSI] scsi_dh_alua: Evaluate TPGS setting from inquiry data
Instead of issuing a standard inquiry from within the
alua device handler we can evaluate the TPGS setting from
the existing inquiry data of the sdev and save us the I/O.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Christoph Hellwig [Sat, 16 Jul 2011 19:00:35 +0000 (15:00 -0400)]
[SCSI] libsas: fix sas_queuecommand return values
->queuecommand must return either 0, or one of the SCSI_MLQUEUE_* return
values. Non-transient errors are indicated by setting cmd->result before
calling ->scsi_done and returning 0. Fix libsas to adhere to this calling
convention. Note that the DID_ERROR for returns from the low-level driver
might not be correct for all cases, but it's the best we can do with
the current layering in libsas. I also suspect that the pre-existing
handling of -SAS_QUEUE_FULL should really be SCSI_MLQUEUE_HOST_BUSY, but
I'll leave that for a separate change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Christoph Hellwig [Mon, 11 Jul 2011 18:49:24 +0000 (14:49 -0400)]
[SCSI] libsas: reindent sas_queuecommand
Switch sas_queuecommand to a normal indentation and goto based error handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Christoph Hellwig [Mon, 11 Jul 2011 18:49:23 +0000 (14:49 -0400)]
[SCSI] libsas: sas_queuecommand doesnt need host_lock
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Nao Nishijima [Thu, 25 Aug 2011 09:04:14 +0000 (18:04 +0900)]
[SCSI] sd: Use sd_printk() instead of printk()
sd_ioctl() still use printk() for log output.
It should use sd_printk() instead of printk(), as well as other sd_*.
All SCSI messages should output via s*_printk() instead of printk().
Signed-off-by: Nao Nishijima <nao.nishijima.xt@hitachi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Nao Nishijima [Thu, 25 Aug 2011 09:04:06 +0000 (18:04 +0900)]
[SCSI] genhd: add a new attribute "alias" in gendisk
This patch allows the user to set an "alias" of the disk via sysfs interface.
This patch only adds a new attribute "alias" in gendisk structure.
To show the alias instead of the device name in kernel messages,
we need to revise printk messages and use alias_name() in them.
Example:
(current) printk("disk name is %s\n", disk->disk_name);
(new) printk("disk name is %s\n", alias_name(disk));
Users can use alphabets, numbers, '-' and '_' in "alias" attribute. A disk can
have an "alias" which length is up to 255 bytes. This attribute is write-once.
Suggested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Suggested-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Nao Nishijima <nao.nishijima.xt@hitachi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Thu, 25 Aug 2011 05:36:38 +0000 (00:36 -0500)]
[SCSI] scsi scan: don't fail scans when host is in recovery
The problem is that if we are doing a scsi scan then the device goes
into recovery then we will wait for the recovery to complete. It waits
because scsi-ml will send inquiries or report luns and the queueing code
will have been blocked due to the host not being ready. However, if we
are in recovery and then a scan is started the scan will silently fail
and some devices will not be added.
It is easy to hit the problem where devices do not show up with
FC where we are doing tests that disrupt the target controllers.
When the controller is disruprted (reboot, or setting firmware, etc),
and we cause the dev loss tmo to fire then devices will be removed
Then when the problem has been fixed, the rport will be scanned and
devices should be added back. But if we cause another disruption before
scanning has started then devices will not get added back. If the problem
is not started until the scan is started then the devices will be added
back.
This patch fixes that problem by not failing scans when the host
is in recovery. We will let scsi-ml send the IO and let the queueing
and scsi error handling deal with it like is done if we went into
recovery while scanning.
For recovery cases where the host is being torn down then with the
patch we will still fail the scan since there is not point in scanning.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Thu, 25 Aug 2011 01:56:42 +0000 (18:56 -0700)]
[SCSI] bnx2fc: Need not schedule destroy_work from __bnx2fc_destroy
Since it is already called in the right context with rtnl_lock and dev_mutex
held.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Mon, 22 Aug 2011 01:49:49 +0000 (21:49 -0400)]
[SCSI] lpfc 8.3.26: Change driver version to 8.3.26
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Mon, 22 Aug 2011 01:49:16 +0000 (21:49 -0400)]
[SCSI] lpfc 8.3.26: Fix SYSFS interface issues
Fix SYSFS interface issues.
- In the lpfc_sli4_pdev_status_reg_wait() routine, after initial 100ms delay
following write to PHYSDEV_CONTROL register for the firmware reaction, check
the RN bit and ERR bit of the SLIPORT_STATUS register. If none of them
became 1, the previous PHYSDEV_CONTROL register should be considered failed
due to lack of privilege and error for no permission should be returned
immediately without getting into the wait for RDY bits on the SLIPORT_STATUS
register.
- Remove the driver check on dev->is_physfn before proceed to perform the
PHYSDEV_CONTROL register write, and let the PCI function's privilege
setting and driver handling of PHYSDEV_CONTROL register write failure to
handle the reset-ability through the SLI port.
- Added key to ctlreg_write to prevent unauthorized or unexpected write to
the control register.
- Change return to EACCES for sysfs access that are failed because hba_reset
is disabled.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Mon, 22 Aug 2011 01:48:49 +0000 (21:48 -0400)]
[SCSI] lpfc 8.3.26: Fix HBA initialization issues
Fix HBA initialization issues
- Swap all values that come from the firmware image on little endian systems.
Created a new bf_get_be macro that does the same as the bf_get_le macro but
for big endian data instead of little endian data.
- Moved the incrementing of temp_offset after the copy
fixed the write object loop to use temp_offset to figure out where the end
of the image is instead of offset.
- Added the necessary codes for properly bringing the driver instance offline
and then trying to bring the port back online with the PCI function IP reset.
If it fails to bring the SLI port back online, it will fall through to
bringing the SLI port to HBA error offline.
- Add a call in the probe_one_s3 and probe_one_s4 routines to get the Modeldesc
- Change OCe50100 to OCe15100
- Made the error log also include the PCI BAR bitmap returned from kernel call
pci_select_bars().
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Mon, 22 Aug 2011 01:48:13 +0000 (21:48 -0400)]
[SCSI] lpfc 8.3.26: Fix issues pertaining to SCSI/FC protocol.
Fix issues pertaining to SCSI/FC protocol.
- Allow frames destined to 0xFFFFFE to be processed by the driver by matching
that DID with the physical port.
- Call lpfc_sli_issue_iocb with context1 set to ndlp
- In echo command accept function, adjust memcpy to limit memcpy to 1K
- Set LPFC_SLI3_BG_ENABLED properly upon completion.
- Skip the INIT_VFI call in lpfc_register_fcf if the FCF is already
registered and go immediately to initial flogi.
- use "status" variable instead of "ret" variable to hold the return of the
fc_block_scsi_eh.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jayamohan Kallickal [Mon, 22 Aug 2011 17:08:29 +0000 (10:08 -0700)]
[SCSI] be2iscsi: Add pci_disable device
This patch adds call to pci_disable_device during
rmmod and shutdown. The lack of this call was causing hang in
insmod - rmmod loop test
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jayamohan Kallickal [Mon, 22 Aug 2011 17:08:28 +0000 (10:08 -0700)]
[SCSI] be2iscsi: Adding a shutdown Routine
This patch adds a shutdown routine. It fixes a bug where when be2net
and be2iscsi are both used be2iscsi was not cleaning up its resources
properly causing be2net to fail to get loaded when the system is
rebooted.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jayamohan Kallickal [Wed, 24 Aug 2011 23:05:30 +0000 (16:05 -0700)]
[SCSI] be2iscsi: Fixing the /proc/interrupts problem V3
Fix be2iscsi driver to use a separate pointer for each irq action->name
field and avoid display corruption in /proc/interrupts. The be2iscsi driver
was using a single static array in a function for the irq action->name field.
This results in garbage output from /proc/interrupts
The pointer for action->name is garbage and scribbles the output on the screen.
This patch fixes the problem:
156: 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 PCI-MSI-X beiscsi_msix_0017
This patch is based on Prarit's patch here:
http://www.spinics.net/lists/linux-scsi/msg52325.html
but I have fixed up the failure paths and removed
redundant check for !i suggested by Eike.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Chad Dupuis [Tue, 16 Aug 2011 18:31:55 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Fix "active_mask" may be used uninitialized warning.
Since active_mask is first assigned in an "else" block, the compiler throws
a warning saying that the active_mask variable may be used uninitialized in
a print statement later. Initialize active_mask to 0 in the declaration to
stop the warning.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Giridhar Malavali [Tue, 16 Aug 2011 18:31:54 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Issue mailbox command only when firmware hung bit is reset for ISP82xx.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Joe Carnuccio [Tue, 16 Aug 2011 18:31:53 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Return sysfs error codes appropriate to conditions.
Return sysfs error codes that match the conditions encountered.
This prevents sysfs from retrying a request which is conditioned
to fail under the current circumstance.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Joe Carnuccio [Tue, 16 Aug 2011 18:31:52 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Provide method for updating I2C attached VPD.
Provide bsg interface for updating VPD attached on the I2C serial bus.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Joe Carnuccio [Tue, 16 Aug 2011 18:31:51 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Correction to sysfs edc interface.
Corrects the return value for the cases where read/write edc fails;
this prevents sysfs from retrying the operation until forever.
Corrects the printk width specifier for the first byte of buf.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Saurav Kashyap [Tue, 16 Aug 2011 18:31:50 +0000 (11:31 -0700)]
[SCSI] qla2xxx: During loopdown perform Diagnostic loopback.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Saurav Kashyap [Tue, 16 Aug 2011 18:31:49 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Fix array out of bound warning.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Saurav Kashyap [Tue, 16 Aug 2011 18:31:48 +0000 (11:31 -0700)]
[SCSI] qla2xxx: check for marker IOCB during response queue processing.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Chad Dupuis [Tue, 16 Aug 2011 18:31:47 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Enable write permission to some debug related module parameters to be changed dynamically.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Saurav Kashyap [Tue, 16 Aug 2011 18:31:46 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Prevent CPU lockups when "ql2xdontresethba" module param is set.
Driver is not releasing the lock if ql2xdontresethba is set, this might lead
to a lockup.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Saurav Kashyap [Tue, 16 Aug 2011 18:31:45 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Implemeted beacon on/off for ISP82XX.
[jejb: fix up checkpatch.pl errors]
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Giridhar Malavali [Tue, 16 Aug 2011 18:31:44 +0000 (11:31 -0700)]
[SCSI] qla2xxx: Add support for ISP82xx to capture dump (minidump) on failure.
Minidump allows us to catpure a snapshot of the firmware/hardware states at the
time of failure for further analysis.
[jejb: added missing #include <linux/vmalloc.h>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Swen Schillig [Mon, 15 Aug 2011 12:40:32 +0000 (14:40 +0200)]
[SCSI] zfcp: support for hardware data router
FICON Express8S supports hardware data router, which requires an
adapted qdio request format.
This part 2/2 exploits the functionality in zfcp.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Swen Schillig [Mon, 15 Aug 2011 12:40:31 +0000 (14:40 +0200)]
[SCSI] qdio: base support for hardware data router with zfcp
FICON Express8S supports hardware data router, which requires an
adapted qdio request format.
This part 1/2 provides the qdio base required for exploitation in
zfcp.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Steffen Maier [Mon, 15 Aug 2011 12:40:30 +0000 (14:40 +0200)]
[SCSI] zfcp: non-experimental support for DIF/DIX
DIF/DIX support for zfcp is no longer experimental,
and config option is no longer necessary.
Return error from queuecommand for unsupported data directions.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jianyun Li [Wed, 11 May 2011 15:22:44 +0000 (23:22 +0800)]
[SCSI] mvumi: Add Marvell UMI driver
The Marvell Universal Message Interface (UMI) defines a messaging
interface between host and Marvell products (Plato, for example). It
considers situations of limited system resource and optimized system
performance.
UMI driver translates host request to message and sends message
to FW via UMI, FW receives message and processes it, then sends response
to UMI driver.
FW generates an interrupt when it needs to send information or
response to UMI driver
Signed-off-by: Jianyun Li <jyli@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 15 Aug 2011 01:42:56 +0000 (20:42 -0500)]
[SCSI] qla4xxx: export iface name
Export the name of iface session is attached to. This is needed
so tools like iscsiadm/iscsistart can match the sessions to
userspace ifaces when rebuilding iscsid's state during boot.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Fri, 12 Aug 2011 09:51:29 +0000 (02:51 -0700)]
[SCSI] qla4xxx: Added support for adapter and firmware reset
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Fri, 12 Aug 2011 09:51:28 +0000 (02:51 -0700)]
[SCSI] scsi: Added support for adapter and firmware reset
Added new sysfs attr 'host_reset' in scsi_sysfs.c to
perform adapter or firmware reset as suggested by
Mike Christie here:
http://marc.info/?l=linux-scsi&m=
127359347111167&w=2
user/application can write "adapter" or "firmware" on
this attr and it will call newly added function hook
in scsi_host_template to call LDD adapter or firmware
reset implementation.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Harish Zunjarrao [Fri, 12 Aug 2011 09:51:27 +0000 (02:51 -0700)]
[SCSI] qla4xxx: Added Get ACB support using BSG
This command is used to read ACB params from firmware
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Harish Zunjarrao [Fri, 12 Aug 2011 09:51:26 +0000 (02:51 -0700)]
[SCSI] qla4xxx: Added restore factory defaults support using BSG
This command will causes the firmware to update all
configurations to pre-defined factory default settings.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
TARUISI Hiroaki [Thu, 11 Aug 2011 11:25:20 +0000 (20:25 +0900)]
[SCSI] Fix out of spec CD-ROM problem with media change
Some CD-ROMs fail to report a media change correctly. The specific
one for this patch simply fails to respond to commands, then gives a
UNIT ATTENTION after being reset which returns ASC/ASCQ 28/00. This
is out of spec behaviour, but add a check in the eat CC/UA on reset
path to catch this case so the CD-ROM will function somewhat properly.
[jejb: fixed up white space and accepted without signoff]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 1 Aug 2011 10:26:19 +0000 (03:26 -0700)]
[SCSI] qla4xxx: added support to update initiator iscsi port
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 1 Aug 2011 10:26:18 +0000 (03:26 -0700)]
[SCSI] scsi_transport_iscsi: Added support to update initiator iscsi port
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 1 Aug 2011 10:26:17 +0000 (03:26 -0700)]
[SCSI] qla4xxx: Added vendor specific sysfs attributes
Added board_id, fw_state, phy_port_cnt, phy_port_num,
iscsi_func_cnt, hba_model
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Harish Zunjarrao [Mon, 1 Aug 2011 10:26:16 +0000 (03:26 -0700)]
[SCSI] qla4xxx: Add read/update NVRAM support for 40xx adapters using BSG
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Harish Zunjarrao [Mon, 1 Aug 2011 10:26:15 +0000 (03:26 -0700)]
[SCSI] qla4xxx: Add get ACB state support using BSG
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Harish Zunjarrao [Mon, 1 Aug 2011 10:26:14 +0000 (03:26 -0700)]
[SCSI] qla4xxx: Code cleanup for read/update flash using BSG
- Corrected return status
- Added reset active check
- Removed unused dma_map_sg calls
- Added debug prints on failure
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 1 Aug 2011 10:26:13 +0000 (03:26 -0700)]
[SCSI] qla4xxx: Added support to update mtu
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 1 Aug 2011 10:26:12 +0000 (03:26 -0700)]
[SCSI] scsi_transport_iscsi: Added support to update mtu
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Manish Rangankar [Mon, 25 Jul 2011 18:48:55 +0000 (13:48 -0500)]
[SCSI] qla4xxx: Boot from SAN support for open-iscsi
Hook qla4xxx in fw boot sysfs interface so iscsi tools
can use the info to create boot sessions.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Manish Rangankar [Mon, 25 Jul 2011 18:48:54 +0000 (13:48 -0500)]
[SCSI] qla4xxx: Remove reduandant code after open-iscsi integration.
1. Remove device database entry (ddb) state.
2. Remove device database (DDB) list building.
With open-iscsi integration the logins to the target devices are
handled by the user space. So the information of target is now
maintained in the iscsi_session object. This is handled at
libiscsi level so there is no need to maintain a list of DDBs in
the qla4xxx LLD.
3. qla4xxx: Remove add_device_dynamically.
Since autologin in FW is disabled with open-iscsi integration,
driver will never get an AEN for which driver has not requested
a DDB index. So remove the add_device_dynamically function.
4. Remove qla4xxx_tgt_dscvr
Since firmware autologin is disabled this function will not work.
Now user has the ability to do the target discovery and login to
each target individually. Firwmare will not do the login on its own.
5. Remove relogin related code
All relogin is handled by userspace now. qla4xxx just need to
notify userspace of a connection failure, this triggers the
relogin.
6. Remove add_session and alloc_session
Now qla4xxx uses iscsi_session_setup that would do the necessary
allocations for session and ddb_entry.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Manish Rangankar [Mon, 25 Jul 2011 18:48:53 +0000 (13:48 -0500)]
[SCSI] qla4xxx: support iscsiadm session mgmt
Add scsi_transport_iscsi hooks in qla4xxx to support
iSCSI session management using iscsiadm.
This patch is based on discussion here
http://groups.google.com/group/open-iscsi/browse_thread/thread/
e89fd888baf656a0#
Now users can use iscsiadm to do target discovery and do login/logout to
individual targets using the qla4xxx iSCSI class interface.
This patch leaves some dead code, but to make it easier to review
we are leaving and in the next patch we will remove that old code.
V2 - NOTE: Added code to avoid waiting for AEN during login/logout
in the driver, instead added a kernel to user event
to notify iscsid about login status. Because of this
iscsid will not get blocked.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Manish Rangankar [Mon, 25 Jul 2011 18:48:52 +0000 (13:48 -0500)]
[SCSI] scsi_transport_iscsi: Add conn login, kernel to user, event to support offload session login.
Offload drivers like qla4xxx will offload the sending of the login/logout
pdus still, so this patch adds iscsi_conn_login_event which is
used by these types of drivers to notify userspace that the connection
has changed state.
It also adds a iscsi_is_session_online helper so the lld
can query the sessions state field.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 25 Jul 2011 18:48:51 +0000 (13:48 -0500)]
[SCSI] qla4xxx: add bsg support
This patch adds bsg support to qla4xxx.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:50 +0000 (13:48 -0500)]
[SCSI] iscsi class: add bsg support to iscsi class
This patch adds bsg support to the iscsi class. There is only
1 request, the host vendor one, supported. It is expected that
this would be used for things like flash updates.
This patch is made over this one
http://marc.info/?l=linux-scsi&m=
131149780020992&w=2
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 25 Jul 2011 18:48:49 +0000 (13:48 -0500)]
[SCSI] qla4xxx: Add VLAN support
Add support to set VLAN and show vlan settings in sysfs
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
[Patch updated to new defines]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:48 +0000 (13:48 -0500)]
[SCSI] libiscsi: don't bugon when if user sets markers
libiscsi does not support markers and if someone tries
to set them the driver does a BUG(). There is not need
to be that extreme. Just return -ENOSYS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:47 +0000 (13:48 -0500)]
[SCSI] iscsi class: expand vlan support
Add support to set vlan priority and enable/disble a vlan.
Patch based on code from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:46 +0000 (13:48 -0500)]
[SCSI] be2iscsi: remove host and session casts
iscsi_session_to_shost is a macro around dev_to_shost which returns a
Scsi_Host so there is no need to cast.
iscsi_session_to_shost is a macro around shost_priv which
returns a void pointer so no need to cast.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:45 +0000 (13:48 -0500)]
[SCSI] iscsi class: sysfs group is_visible callout for iscsi host attrs
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:44 +0000 (13:48 -0500)]
[SCSI] iscsi class: remove iface param mask
We can replace the iface param mask with the
attr_is_visible callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:43 +0000 (13:48 -0500)]
[SCSI] iscsi class: sysfs group is_visible callout for session attrs
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's session attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:42 +0000 (13:48 -0500)]
[SCSI] iscsi cls: sysfs group is_visible callout for conn attrs
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and drivers to use the attribute container
sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 25 Jul 2011 18:48:41 +0000 (13:48 -0500)]
[SCSI] qla4xxx: added support to show multiple iface in sysfs
Add support for default ipv4 and ipv6 ifaces in qla4xxx.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Reviewed-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
[make iface creation dynamic]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:40 +0000 (13:48 -0500)]
[SCSI] iscsi class: add iface representation
A iscsi host can have multiple interfaces. This patch
adds a new iface iscsi class for this. It exports the
network settings now, and will be extended to also
export iscsi initiator port settings like the isid
and initiator name for drivers that can support multiple
initiator ports.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 25 Jul 2011 18:48:39 +0000 (13:48 -0500)]
[SCSI] qla4xxx: Added new "struct ipaddress_config"
- Move all ipaddress related param to "struct ipaddress_config"
from "struct scsi_qla_host"
- update function - qla4xxx_update_local_ip()
- Rename IPOPT_IPv4_PROTOCOL_ENABLE to IPOPT_IPV4_PROTOCOL_ENABLE
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
[update for new ISCSI_IFACE values]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:38 +0000 (13:48 -0500)]
[SCSI] qla4xxx: add support for set_net_config
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patches from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike Christie [Mon, 25 Jul 2011 18:48:37 +0000 (13:48 -0500)]
[SCSI] iscsi_transport: add support for net settings
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Anton Blanchard [Mon, 1 Aug 2011 09:43:45 +0000 (19:43 +1000)]
[SCSI] ipr: Always initiate hard reset in kdump kernel
During kdump testing I noticed timeouts when initialising each IPR
adapter. While the driver has logic to detect an adapter in an
indeterminate state, it wasn't triggering and each adapter went
through a 5 minute timeout before finally going operational.
Some analysis showed the needs_hard_reset flag wasn't getting set.
We can check the reset_devices kernel parameter which is set by
kdump and force a full reset. This fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
kashyap.desai@lsi.com [Fri, 5 Aug 2011 05:34:37 +0000 (11:04 +0530)]
[SCSI] mptfusion: Fix for device offline while doing aggressive HBA reset
[Resend patch as per Bernd Schubert comment ]
Issue:
Device goes offline while doing aggressive HBA reset
along with IO using some utility.
Root cause:
FW goes into bad state due to aggressive reset. Softreset does not
help to recover FW. And also aggressive reset open up the window for
Error handling thread to kicked off at the same time HBA will be in
constant RESET loop as part of aggressive reset test case can lead
Device to goes offline.
Changes:
1. Added extra check as below inside eh_timed_out call back as below.
if(ioc->ioc_reset_in_progress) Rc = EH_TIMER_RESET
2. Removed " DOORBELL_ACTIVE" check for SAS controller from task
management context. Since SAS controller uses high priority queue
for task management. This check is not required for SAS controller.
3. Moved SoftReset call to HardReset from Task Mgmt context.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:52 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Bump version to 1.0.5
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:51 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Prevent creating of NPIV port with duplicate WWN
This patch adds a validation step before allowing creation of a new NPIV port.
It checks whether the WWPN passed for the new NPIV port to be created is unique
for the given physical port.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:50 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Obtain WWNN/WWPN from the shared memory
bnx2x driver would obtain the WWNN/WWPN from the shared memory and can be
obtained by the bnx2fc driver via ndo_fcoe_get_wwn.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:49 +0000 (17:38 -0700)]
[SCSI] fcoe: Move common functions to fcoe_transport library
Export fcoe_get_wwn, fcoe_validate_vport_create and fcoe_wwn_to_str so that all
LLDs can use these common function.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:48 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Drop incoming ABTS
As an initiator, driver need not handle incoming ABTS. It initiates an ABTS if
any IO requests time out.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:47 +0000 (17:38 -0700)]
[SCSI] bnx2fc: code cleanup in bnx2fc_offload_session
- Free session resources before rport logoff
- Do not free session resources in bnx2fc_alloc_session_resc() as it is handled
in caller's error handling path.
- Do not call bnx2fc_free_session_resc() if bnx2fc_init_tgt() fails as cq_lock
is not yet initialized.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:46 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Fix NULL pointer deref during arm_cq.
There exists a race condition between CQ doorbell unmap and IO completion path
that arms the CQ which causes a NULL dereference. Protect the ctx_base with
cq_lock to avoid this. Also, wait for the CQ doorbell to be successfully mapped
before arming the CQ.
Also, do not count uncolicited CQ completions for free_sqes.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:45 +0000 (17:38 -0700)]
[SCSI] bnx2fc: IO errors when receiving unsolicited LOGO
During the unsolicited LOGO processing, the session is uploaded and offloaded
after the relogin is complete. In between any new IOs are errored back as the
upload completion flag is set. Upon exhausting the retry count, the application
fails the IOs. Return target busy for all the cases when session is not ready.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:44 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Do not reuse the fcoe connection id immediately
CFC_DELETE is issued 2 secs after CONN_TERM is completed. If the session is
uploaded and offloaded immediately, it has to wait for the connection id to be
available.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:43 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Clear DESTROY_CMPL flag after firmware destroy
Since this flag was never cleared, the driver does not wait for firmware
destroy completions, causing missed KCQEs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:42 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Handle NETDEV_UNREGISTER for vlan devices
Since the driver holds the reference for vlan netdev, the reference has to be
released by the driver when the vlan device is removed. Driver handles this in
NETDEV_UNREGISTER event.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:41 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Reorganize cleanup code between interface_cleanup and if_destory
Move interface specific cleanup functionality to from bnx2fc_if_destroy to
bnx2fc_interface_cleanup. Do not access interface/hba in bnx2fc_if_destroy as
by the time this function is called interface may already be destroyed. This
patch is in preparation to handle NETDEV_UNREGISTER on a vlan device.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:40 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Change function names of bnx2fc_netdev_setup/bnx2fc_netdev_cleanup
Change them to bnx2fc_interface_setup/bnx2fc_interface_cleanup in preperation
for the patches to follow. Interface specific cleanup functionality will be
moved to bnx2fc_interface_cleanup.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:39 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Do not attempt destroying NPIV port twice
When NPIV ports are created/deleted rapidly there is a race condition between
bnx2fc_vport_destroy() from sysfs and bnx2fc_flogi_resp(), which could try to
delete the NPIV port from the list twice. Fix is to loop through the list of
NPIV ports to find a match, and only when it exists remove it.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:38 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Remove erroneous kref_get on IO request
During sequence cleanup, an additional reference for an IO has been
taken. Because of this, the IO is never released into the free list.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:37 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Enable bsg_request support for bnx2fc
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:36 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Bug fixes in percpu_thread_create/destroy
Look up p->work_list to process cq completions, and correct the error check for
thread creation.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 5 Aug 2011 00:38:35 +0000 (17:38 -0700)]
[SCSI] bnx2fc: Reset the max receive frame size
Reset max receive frame size every time before attempting FLOGI. Without this,
the stale MFS value will be used.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
kashyap.desai@lsi.com [Thu, 4 Aug 2011 11:17:50 +0000 (16:47 +0530)]
[SCSI] mpt2sas: Added missing mpt2sas_base_detach call from scsih_remove context
mpt2sas_base_detach() call was removed from _scsih_remove() while
doing some code shuffling. Mainly when we work on adding code for
scsih_shutdown(). I have added back mpt2sas_base_detach() which will
get callled from _scsih_remove().
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>