OSDN Git Service
Linus Torvalds [Sat, 12 Dec 2009 19:40:13 +0000 (11:40 -0800)]
Merge branch 'omap-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (75 commits)
omap3: Fix OMAP35XX_REV macros
omap: serial: fix non-empty uart fifo read abort
omap3: Zoom2/3: Update hsmmc board config params
omap3 : Enable TWL4030 Keypad for Zoom2 and Zoom3 boards
omap3: id code detection 3525 vs 3515
omap3: rx51: Use wl1251 in SPI mode 3
omap3: zoom2/3: make MMC slot work again
omap1: htcherald: Update defconfig to include mux support
omap1: LCD_DMA: Use some define rather than a hexadecimal
omap: header: remove unused data-type
omap: arch/arm/plat-omap/devices.c - sort alphabetically
omap: Correcting GPMC_CONFIG1_DEVICETYPE_NAND
OMAP3: serial - allow platforms specify which UARTs to initialize
omap3: cm-t35: add mux initialization
OMAP4: Sync up omap4430 defconfig
OMAP4: Remove the secondary wait loop
OMAP4: AuxCoreBoot registers only accessible in secure mode
OMAP4: Fix SRAM base and size
OMAP4: Fix cpu detection
omap3: pandora: board file updates for .33
...
Linus Torvalds [Sat, 12 Dec 2009 19:39:09 +0000 (11:39 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
be2net: fix error in rx completion processing.
igbvf: avoid reset storms due to mailbox issues
igb: fix handling of mailbox collisions between PF/VF
usb: remove rare pm primitive for conversion to new API
Linus Torvalds [Sat, 12 Dec 2009 19:37:39 +0000 (11:37 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slab, kmemleak: pass the correct pointer to kmemleak_erase()
slab, kmemleak: stop calling kmemleak_erase() unconditionally
SLAB: Fix unlikely() annotation in __cache_alloc_node()
SLAB: Fix lockdep annotations for CPU hotplug
SLUB: Fix __GFP_ZERO unlikely() annotation
slub: allow stats to be cleared
Linus Torvalds [Sat, 12 Dec 2009 19:34:10 +0000 (11:34 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (21 commits)
sched: Remove forced2_migrations stats
sched: Fix memory leak in two error corner cases
sched: Fix build warning in get_update_sysctl_factor()
sched: Update normalized values on user updates via proc
sched: Make tunable scaling style configurable
sched: Fix missing sched tunable recalculation on cpu add/remove
sched: Fix task priority bug
sched: cgroup: Implement different treatment for idle shares
sched: Remove unnecessary RCU exclusion
sched: Discard some old bits
sched: Clean up check_preempt_wakeup()
sched: Move update_curr() in check_preempt_wakeup() to avoid redundant call
sched: Sanitize fork() handling
sched: Clean up ttwu() rq locking
sched: Remove rq->clock coupling from set_task_cpu()
sched: Consolidate select_task_rq() callers
sched: Remove sysctl.sched_features
sched: Protect sched_rr_get_param() access to task->sched_class
sched: Protect task->cpus_allowed access in sched_getaffinity()
sched: Fix balance vs hotplug race
...
Fixed up conflicts in kernel/sysctl.c (due to sysctl cleanup)
Pekka Enberg [Sat, 12 Dec 2009 08:12:19 +0000 (10:12 +0200)]
Merge branches 'slab/fixes', 'slab/kmemleak', 'slub/perf' and 'slub/stats' into for-linus
Ajit Khaparde [Sat, 12 Dec 2009 06:59:09 +0000 (22:59 -0800)]
be2net: fix error in rx completion processing.
There are certain skews of the NIC which have multiple bits set in
adapter->cap. Use & instead of == to process rx completions.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Sat, 12 Dec 2009 06:58:14 +0000 (22:58 -0800)]
igbvf: avoid reset storms due to mailbox issues
From: Alexander Duyck <alexander.h.duyck@intel.com>
This change makes it so that reset/interrupt storms can be avoided when
there are mailbox issues. The new behavior is to only allow the device to
trigger mailbox related resets only once every 10 seconds.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Sat, 12 Dec 2009 06:57:34 +0000 (22:57 -0800)]
igb: fix handling of mailbox collisions between PF/VF
This patch changes the handling of collisions between the use of the
PF/VF sides of the mailbox.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Sat, 12 Dec 2009 05:43:00 +0000 (21:43 -0800)]
usb: remove rare pm primitive for conversion to new API
This patch removes a rare use of the USB power management API which
won't be supported after the conversion to the new generic runtime power
management framework. Functionality is not altered.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 12 Dec 2009 04:58:20 +0000 (20:58 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (75 commits)
net: Handle NETREG_UNINITIALIZED devices correctly
can: add the driver for Analog Devices Blackfin on-chip CAN controllers
xfrm: Fix truncation length of authentication algorithms installed via PF_KEY
net: use compat helper functions in compat_sys_recvmmsg
net: fix compat_sys_recvmmsg parameter type
cxgb3: Fixing EEH handlers
cnic: Zero out status block and Event Queue indices.
cnic: Send delete command when shutting down iSCSI ring.
net: smc91x: Fix up type mismatch in smc_drv_resume().
smc91x: fix unused flags warnings on UP systems
MAINTAINERS: Transfering maintainership of cdc-ether
net: Add missing TST_CFG_WRITE bits around sky2_pci_write
net: Fix Yukon-2 Optima TCP offload setup
net: niu uses crc32, so select CRC32
wireless: update old static regulatory domain rules
mac80211: Revert 'Use correct sign for mesh active path refresh'
mac80211: Fixed bug in mesh portal paths
net/mac80211: Correct size given to memset
b43: Remove reset after fatal DMA error
rtl8187: add radio led and fix warnings on suspend
...
Linus Torvalds [Sat, 12 Dec 2009 04:57:46 +0000 (20:57 -0800)]
Merge branch 'compat-ioctl-merge' of git://git./linux/kernel/git/arnd/playground
* 'compat-ioctl-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground:
usbdevfs: move compat_ioctl handling to devio.c
lp: move compat_ioctl handling into lp.c
compat_ioctl: pass compat pointer directly to handlers
compat_ioctl: simplify lookup table
compat_ioctl: simplify calling of handlers
compat_ioctl: inline all conversion handlers
compat_ioctl: Remove BKL
compat_ioctl: remove all VT ioctl handling
Linus Torvalds [Sat, 12 Dec 2009 04:57:31 +0000 (20:57 -0800)]
Merge git://git./linux/kernel/git/arnd/asm-generic
* git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: add sys_recvmmsg to unistd.h
asm-generic: add sys_accept4 to unistd.h
asm-generic/gpio.h: add some forward decls of the device struct
asm-generic: Fix typo in asm-generic/unistd.h.
lib/checksum: fix one more thinko
lib/checksum.c: make do_csum optional
lib/checksum.c: use 32-bit arithmetic consistently
Linus Torvalds [Sat, 12 Dec 2009 04:49:09 +0000 (20:49 -0800)]
Merge branch 'timers-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
itimer: Fix the itimer trace print format
hrtimer: move timer stats helper functions to hrtimer.c
hrtimer: Tune hrtimer_interrupt hang logic
Linus Torvalds [Sat, 12 Dec 2009 04:48:21 +0000 (20:48 -0800)]
Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: Avoid out of bounds array reference in save_trace()
futex: Take mmap_sem for get_user_pages in fault_in_user_writeable
lockstat: Add usage info to Documentation/lockstat.txt
lockstat: Fix min, max times in /proc/lock_stats
Linus Torvalds [Sat, 12 Dec 2009 04:47:59 +0000 (20:47 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Fix PCI hotplug with passthrough mode
x86/amd-iommu: Fix passthrough mode
x86: mmio-mod.c: Use pr_fmt
x86: kmmio.c: Add and use pr_fmt(fmt)
x86: i8254.c: Add pr_fmt(fmt)
x86: setup_percpu.c: Use pr_<level> and add pr_fmt(fmt)
x86: es7000_32.c: Use pr_<level> and add pr_fmt(fmt)
x86: Print DMI_BOARD_NAME as well as DMI_PRODUCT_NAME from __show_regs()
x86: Factor duplicated code out of __show_regs() into show_regs_common()
arch/x86/kernel/microcode*: Use pr_fmt() and remove duplicated KERN_ERR prefix
x86, mce: fix confusion between bank attributes and mce attributes
x86/mce: Set up timer unconditionally
x86: Fix bogus warning in apic_noop.apic_write()
x86: Fix typo in arch/x86/mm/kmmio.c
x86: ASUS P4S800 reboot=bios quirk
Linus Torvalds [Sat, 12 Dec 2009 04:47:44 +0000 (20:47 -0800)]
Merge branch 'tracing-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Remove comparing of NULL to va_list in trace_array_vprintk()
tracing: Fix function graph trace_pipe to properly display failed entries
tracing: Add full state to trace_seq
tracing: Buffer the output of seq_file in case of filled buffer
tracing: Only call pipe_close if pipe_close is defined
tracing: Add pipe_close interface
Linus Torvalds [Sat, 12 Dec 2009 04:47:30 +0000 (20:47 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (57 commits)
x86, perf events: Check if we have APIC enabled
perf_event: Fix variable initialization in other codepaths
perf kmem: Fix unused argument build warning
perf symbols: perf_header__read_build_ids() offset'n'size should be u64
perf symbols: dsos__read_build_ids() should read both user and kernel buildids
perf tools: Align long options which have no short forms
perf kmem: Show usage if no option is specified
sched: Mark sched_clock() as notrace
perf sched: Add max delay time snapshot
perf tools: Correct size given to memset
perf_event: Fix perf_swevent_hrtimer() variable initialization
perf sched: Fix for getting task's execution time
tracing/kprobes: Fix field creation's bad error handling
perf_event: Cleanup for cpu_clock_perf_event_update()
perf_event: Allocate children's perf_event_ctxp at the right time
perf_event: Clean up __perf_event_init_context()
hw-breakpoints: Modify breakpoints without unregistering them
perf probe: Update perf-probe document
perf probe: Support --del option
trace-kprobe: Support delete probe syntax
...
Linus Torvalds [Sat, 12 Dec 2009 04:46:51 +0000 (20:46 -0800)]
Merge branch 'for-linus' of git://codeaurora.org/quic/kernel/dwalker/linux-msm
* 'for-linus' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
HTC Dream: mmc compilation fixes
video: Allow selecting MSM framebuffer in Kconfig
Add arm msm maintainer entry
msm: Add memory map for HTC Dream
msm: add minimal board file for HTC Dream device
msm: make debugging UART (for DEBUG_LL) configurable
David S. Miller [Sat, 12 Dec 2009 01:12:17 +0000 (17:12 -0800)]
Merge branch 'master' of /home/davem/src/GIT/linux-2.6/
Conflicts:
include/net/tcp.h
Tony Lindgren [Sat, 12 Dec 2009 00:19:16 +0000 (16:19 -0800)]
Merge branch 'for-next' into omap-for-linus
Sanjeev Premi [Sat, 12 Dec 2009 00:16:37 +0000 (16:16 -0800)]
omap3: Fix OMAP35XX_REV macros
In original implementation, the revision passed to
these macros contained revision number in lower nibble.
But, later the revision bits (OMAP_REVBITS_XX) were
defined to use omap_revision[15:08] where revision
number is containied in higher nibble.
This patch updates the macros; else incorrect revision
is detected for OMAP35xx devices.
Signed-off-by: Sanjeev Premi <premi@ti.com>
vikram pandita [Sat, 12 Dec 2009 00:16:37 +0000 (16:16 -0800)]
omap: serial: fix non-empty uart fifo read abort
OMAP3xxx and OMAP4430 UART IP blocks have a restriction wrt RX FIFO.
Empty RX fifo read causes an abort.
OMAP3xxx:
UART IP revision >= 0x52 have this issue
MVR register format is:
Bits Field Name Description Type Reset
31:8 RESERVED RO 0x0
7:4 MAJOR Major revision number of the module. RO 0x--
3:0 MINOR Minor revision number of the module. RO 0x--
OMAP4xxx:
All revisions have this issue
Revision id check is not used as the format of MVR resigster has changed
For omap4 MVR register reads as: 0x50410602 => Revision id = 0x0602
Format of MVR register on omap4 is: (Courtesy: Cousson, Benoit)
Bits Field Name Description Type Reset
31:30 SCHEME Scheme revision number of module RO 0x1
29:28 RESERVED RO 0x1
27:16 FUNC Function revision number of module RO 0x041
15:11 RTL Rtl revision number of module RO 0x00
10:8 MAJOR Major revision number of the module. RO 0x6
7:6 CUSTOM Custom revision number of the module. RO 0x0
5:0 MINOR Minor revision number of the module. RO 0x02
Override the default 8250 read handler: mem_serial_in()
by a custom handler: serial_in_8250()
which makes sure that RX fifo is not read when empty
tested on zoom3(3630) board
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Madhusudhan Chikkature [Sat, 12 Dec 2009 00:16:37 +0000 (16:16 -0800)]
omap3: Zoom2/3: Update hsmmc board config params
Update the hsmmc zoom peripheral configuration to support:
Power saving mode
mmc2 8-bit support
Configure mmc2 as non removable
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
manjugk manjugk [Sat, 12 Dec 2009 00:16:37 +0000 (16:16 -0800)]
omap3 : Enable TWL4030 Keypad for Zoom2 and Zoom3 boards
The TWL4030 keypad driver is not enabled by default for zoom2 and zoom3
boards.
This patch will enable the same for both zoom2 and zoom3 boards.
Tested on zoom2(3430) and zoom3(3630) boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sergey Lapin [Sat, 12 Dec 2009 00:16:37 +0000 (16:16 -0800)]
omap3: id code detection 3525 vs 3515
The runtime detection of OMAP3515 and OMAP3525
was reversed.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kalle Valo [Sat, 12 Dec 2009 00:16:37 +0000 (16:16 -0800)]
omap3: rx51: Use wl1251 in SPI mode 3
Otherwise Extreme Lower Power (ELP) wakeup doesn't work properly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Anand Gadiyar [Sat, 12 Dec 2009 00:16:36 +0000 (16:16 -0800)]
omap3: zoom2/3: make MMC slot work again
omap3: zoom2/3: make MMC slot work again
Commit
12f8dfb56 accidentally broke MMC on zoom2/3.
The .vmmc1 field of zoom_twldata was deleted. Restoring it
allows the MMC slot to work again
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cory Maccarrone [Sat, 12 Dec 2009 00:16:36 +0000 (16:16 -0800)]
omap1: htcherald: Update defconfig to include mux support
The existing htcherald_defconfig did not include mux support, which
prevented USB and other functionality from working out of the box.
This change updates the defconfig to add it in. It also aligns the
defconfig to the -rc8 kernel config.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Janusz Krzysztofik [Sat, 12 Dec 2009 00:16:36 +0000 (16:16 -0800)]
omap1: LCD_DMA: Use some define rather than a hexadecimal
The patch corrects the issue introduced with one of my earlier patches:
OMAP: DMA: Fix omapfb/lcdc on OMAP1510 broken when PM set[1]
as pointed out by OMAP subsystem maintainer.
Applies on top of my prevoius patch:
OMAP: DMA: move LCD DMA related code from plat-omap to mach-omap1[2]
Tested on Amstrad Delta
Compile tested with omap_generic_2420_defconfig
[1] http://patchwork.kernel.org/patch/57922/
[2] http://patchwork.kernel.org/patch/61952/
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
vikram pandita [Sat, 12 Dec 2009 00:16:36 +0000 (16:16 -0800)]
omap: header: remove unused data-type
Remove unused data type omap_gpio_switch_config
Thereby also get rid of following sparse warnings:
arch/arm/plat-omap/include/plat/board.h :121:20:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :122:19:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :123:24:
warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ladislav Michl [Sat, 12 Dec 2009 00:16:36 +0000 (16:16 -0800)]
omap: arch/arm/plat-omap/devices.c - sort alphabetically
Comment in omap_init_devices asks to keep init calls and their
implementations in alphabetical order, so let it be that way.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Vimal Singh [Sat, 12 Dec 2009 00:16:35 +0000 (16:16 -0800)]
omap: Correcting GPMC_CONFIG1_DEVICETYPE_NAND
For NAND devices '2' should be used with GPMC_CONFIG1_DEVICETYPE
instead of '1'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mika Westerberg [Sat, 12 Dec 2009 00:16:35 +0000 (16:16 -0800)]
OMAP3: serial - allow platforms specify which UARTs to initialize
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mike Rapoport [Sat, 12 Dec 2009 00:16:35 +0000 (16:16 -0800)]
omap3: cm-t35: add mux initialization
CM-T35 can be assembled with different set of peripherals thus making
certain interfaces available to user as GPIOs or dedicated pins. Because
of it CM-T35 bootloader sets up mux configuration only for pins
necessary to boot the system and the rest of the mux configuration is
done by the kernel. Besides, having mux configuration in the kernel
allows to minimize dependancy on bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Santosh Shilimkar [Sat, 12 Dec 2009 00:16:35 +0000 (16:16 -0800)]
OMAP4: Sync up omap4430 defconfig
Enable minimum features to boot omap4430 on es1.0 samples. v2 versions
removes the "CONFIG_SYSFS_DEPRECATED_V2" since it's deprecated. Without
this older file system doesn't boot. One need to upgrade the filesystem
if getting stuck in first init function.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Santosh Shilimkar [Sat, 12 Dec 2009 00:16:35 +0000 (16:16 -0800)]
OMAP4: Remove the secondary wait loop
The secondary cores wakes up in time so the wait loop is not
necessary anymore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Santosh Shilimkar [Sat, 12 Dec 2009 00:16:35 +0000 (16:16 -0800)]
OMAP4: AuxCoreBoot registers only accessible in secure mode
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Santosh Shilimkar [Sat, 12 Dec 2009 00:16:35 +0000 (16:16 -0800)]
OMAP4: Fix SRAM base and size
This patch fixes the public sram base address and available
size on OMAP4430.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Santosh Shilimkar [Sat, 12 Dec 2009 00:16:34 +0000 (16:16 -0800)]
OMAP4: Fix cpu detection
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.
Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Grazvydas Ignotas [Sat, 12 Dec 2009 00:16:34 +0000 (16:16 -0800)]
omap3: pandora: board file updates for .33
Pandora board file updates:
- change keycodes of game buttons
it was decided not to use ABXY layout by the developers.
- drop i2c bus 3 speed to 100kHz
this is needed for battery monitoring chip to work reliably.
- drop pandora_lcd platform_device
the older DSS driver was never functional on l-o or mainline
kernels due to missing panel driver, so remove unneeded
pandora_lcd platform_device. This also removes last OMAP_TAG
from the board file.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gregoire Gentil [Sat, 12 Dec 2009 00:16:34 +0000 (16:16 -0800)]
omap3: Defconfig file of Always Innovating OMAP3-based Touch Book
Defconfig file of Always Innovating OMAP3-based Touch Book
Signed-off-by: Gregoire Gentil <gregoire@gentil.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gregoire Gentil [Sat, 12 Dec 2009 00:16:34 +0000 (16:16 -0800)]
omap3: Board file of Always Innovating OMAP3-based Touch Book
Board file of Always Innovating OMAP3-based Touch Book
Signed-off-by: Gregoire Gentil <gregoire@gentil.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cory Maccarrone [Sat, 12 Dec 2009 00:16:34 +0000 (16:16 -0800)]
omap1: I2C mux and clocks for omap7xx
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cory Maccarrone [Sat, 12 Dec 2009 00:16:34 +0000 (16:16 -0800)]
omap1: Add omap7xx USB support
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Janusz Krzysztofik [Sat, 12 Dec 2009 00:16:33 +0000 (16:16 -0800)]
omap1: DMA: move LCD related code from plat-omap to mach-omap1
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ladislav Michl [Sat, 12 Dec 2009 00:16:33 +0000 (16:16 -0800)]
omap1: Use gen_nand
Since omapnand driver never find its way into mainline, switch to gen_nand instead.
Following patch is compile tested only, but it is based on code I wrote for
NetStar board and runtime tested it there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Kevin Hilman <kjh@hilman.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ladislav Michl [Sat, 12 Dec 2009 00:16:33 +0000 (16:16 -0800)]
smc91x: remove OMAP specific bits
Now that all OMAP boards are using the board resources, we don't need
to keep the arch/board specific crap in the driver header.
Cc: linux-net@vger.kernel.org
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ladislav Michl [Sat, 12 Dec 2009 00:16:33 +0000 (16:16 -0800)]
omap: use smc91x_platdata to setup smc91x
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sat, 12 Dec 2009 00:16:33 +0000 (16:16 -0800)]
omap: mux: Add 36xx CBP package support
Add 36xx CBP package support
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sat, 12 Dec 2009 00:16:33 +0000 (16:16 -0800)]
omap: mux: Remove old mux code for 34xx
Remove old mux code for 34xx
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sat, 12 Dec 2009 00:16:32 +0000 (16:16 -0800)]
omap: mux: Replace omap_cfg_reg() with new style signal or gpio functions
Replace omap_cfg_reg() with new style signal or gpio functions
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sat, 12 Dec 2009 00:16:32 +0000 (16:16 -0800)]
omap: Split i2c platform init for mach-omap1 and mach-omap2
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sat, 12 Dec 2009 00:16:32 +0000 (16:16 -0800)]
omap: mux: Add debugfs support for new mux code
Add debugfs support for new mux code
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sat, 12 Dec 2009 00:16:32 +0000 (16:16 -0800)]
omap: mux: Add new style init functions to omap3 board-*.c files
Add new style mux init functions to omap3 board-*.c files
So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sat, 12 Dec 2009 00:16:32 +0000 (16:16 -0800)]
omap: mux: Add new style pin multiplexing data for 34xx
Add new style mux data for 34xx. This should also
work with 3630 easily by adding the processor subset
and ball data.
Note that this data is __initdata, and gets optimized
out except for the GPIO pins if CONFIG_OMAP_MUX
is not set.
Also note that this data uses omap3630 naming for
the SDMMC registers instead of 34xx naming with just
MMC.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sat, 12 Dec 2009 00:16:32 +0000 (16:16 -0800)]
omap: mux: Add new style pin multiplexing code for omap3
Initially only for 34xx. This code allows us to:
- Make the code more generic as the omap internal signal
names can stay the same across omap generations for some
devices
- Map mux registers to GPIO registers that is needed for
dynamic muxing of pins during off-idle
- Override bootloader mux values via kernel cmdline using
omap_mux=some.signa1=0x1234,some.signal2=0x1234
- View and set the mux registers via debugfs if
CONFIG_DEBUG_FS is enabled
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mike Rapoport [Sat, 12 Dec 2009 00:16:31 +0000 (16:16 -0800)]
omap2: mux: intoduce omap_mux_{read,write}
intoduce omap_mux_{read,write}
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Sat, 12 Dec 2009 00:16:02 +0000 (16:16 -0800)]
Merge branch 'for_2_6_33' of git://git.pwsan.com/linux-2.6 into omap-for-linus
Rajendra Nayak [Wed, 9 Dec 2009 01:47:17 +0000 (18:47 -0700)]
ARM: OMAP4: PM: Add init api for DPLL nodes
An api at init for all dpll nodes seem to be
needed to reparent the dpll clk node to its
bypass clk in case the dpll is in bypass.
If not done this causes sequencing issues at init
during propogate_rate.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:47:16 +0000 (18:47 -0700)]
ARM: OMAP4: PM: Add support for OMAP4 dpll api's
Most of the dpll api's from dpll.c are reused for OMAP4.
This patch does extend a few api's for OMAP4 support.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:47:16 +0000 (18:47 -0700)]
ARM: OMAP4: PM: Move DPLL control apis to dpll.c
This patch moves all the dpll control api's to a
common file dpll.c. This is in preperation of omap4
support wherein most of these api's can be reused.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Tue, 8 Dec 2009 18:31:44 +0000 (00:01 +0530)]
ARM: OMAP4: PM: Add dummy hooks for OMAP4 dpll api's
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:46:28 +0000 (18:46 -0700)]
ARM: OMAP4: PM: OMAP4 clock tree and clkdev registration
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:24:54 +0000 (18:24 -0700)]
ARM: OMAP4: PM: Adds CM1/2 register field masks
This patch adds OMAP4 specific CM1 and CM2 module
register field masks. Auto generated using a python
script (gen_cm_shifts_and_mask.py) developed by Benoit
Cousson, Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:24:52 +0000 (18:24 -0700)]
ARM: OMAP4: PM: Adds PRM register shift and mask bits
This patch adds OMAP4 specific PRM register bit field
shifts and masks. Auto generated using a python script
(gen_prm_shifts_and_mask.py) developed by Benoit Cousson,
Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:24:51 +0000 (18:24 -0700)]
ARM: OMAP4: PM: Adds PRM register defs for OMAP4
This patch adds OMAP4 specific PRM register defs. Auto generated
using a python script (gen_prm_4430_h.py) developed by Paul
Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:24:50 +0000 (18:24 -0700)]
ARM: OMAP4: PM: Adds CM1/2 register defs for OMAP4
This patch adds OMAP4 specific CM1 and CM2 module
register defs. Autogenerated using a python scripts
(gen_cm1_4430_h.py,gen_cm2_4430_h.py) developed
by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:24:49 +0000 (18:24 -0700)]
ARM: OMAP4: PM: PRM/CM module offsets for OMAP4
This patch adds the offsets for new modules in PRM
and CM for OMAP4
These are autogenerated using a python script (gen_prcm44xx_h.py)
developed by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:24:49 +0000 (18:24 -0700)]
ARM: OMAP4: PM: Fix the PRM and CM base addresses
This patch fixes the PRM and CM base addresses and adds
a new CM2 base address for OMAP4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Kevin Hilman [Tue, 8 Dec 2009 23:34:26 +0000 (16:34 -0700)]
OMAP: omap_device: track latency in nanoseconds
Rather than having to do a usecs = nsecs / NSECS_PER_USEC to
track latency in usecs, just track it in nanoseconds.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kevin Hilman [Tue, 8 Dec 2009 23:34:25 +0000 (16:34 -0700)]
OMAP: omap_device: fix nsec/usec conversion in latency calculations
Use
usecs = nsecs / NSEC_PER_USEC;
instead of
usecs = nsecs * NSEC_PER_USEC;
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kevin Hilman [Tue, 8 Dec 2009 23:34:24 +0000 (16:34 -0700)]
OMAP: hwmod: warn on missing clockdomain
WARN if a clock/hwmod is missing a clockdomain association since
resulting hwmod will not be able to correctly enable/disable clocks.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kevin Hilman [Tue, 8 Dec 2009 23:34:23 +0000 (16:34 -0700)]
OMAP: omap_device: use read_persistent_clock() instead of getnstimeofday()
During suspend and resume, when omap_device deactivation and
activation is happening, the timekeeping subsystem has likely already
been suspended. Thus getnstimeofday() will fail and trigger a WARN().
Use read_persistent_clock() instead of getnstimeofday() to avoid this.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kevin Hilman [Tue, 8 Dec 2009 23:34:22 +0000 (16:34 -0700)]
OMAP: omap_device: use UINT_MAX for default wakeup latency limit
The _dev_wakeup_lat_limit field of struct omap_device is u32, so use
UINT_MAX instead of INT_MAX for the default maximum.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kevin Hilman [Tue, 8 Dec 2009 23:34:17 +0000 (16:34 -0700)]
OMAP: omap_device: add to_omap_device() macro
Following the model of to_platform_device(), add to_omap_device()
macro so a platform_device pointer can be converted into an
omap_device pointer.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Tue, 8 Dec 2009 23:34:17 +0000 (16:34 -0700)]
OMAP3 hwmod: drop most of the OCP_SYSCONFIG.CLOCKACTIVITY code
Earlier, the hwmod code had considered the OCP_SYSCONFIG.CLOCKACTIVITY
bits to be incremental power saving bits, controlling internal IP
block clock gates. This was a misapprehension. The CLOCKACTIVITY
bits are used to indicate, in advance, which clocks will be cut when
the module acknowledges an idle request. This enables the IP block to
take whatever action is necessary to complete any in-progress work
before asserting its IdleAck.
In the current Linux-OMAP code, this implies that the clock framework
should be changing module CLOCKACTIVITY bits as module clocks are enabled
and disabled. We don't do that yet, but in the future, we should.
This must wait until the clock tree is annotated with omap_hwmod pointers
(or vice-versa). In the meantime, drop most of the hwmod code that
controls CLOCKACTIVITY bits to avoid confusion.
This patch has benefited from many illuminating discussions with (in
alphabetical order) Benoît Cousson <b-cousson@ti.com>, Rajendra Nayak
<rnayak@ti.com>, and Sebastien Sabatier <s-sabatier1@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Sebastien Sabatier <s-sabatier1@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Paul Walmsley [Tue, 8 Dec 2009 23:34:16 +0000 (16:34 -0700)]
OMAP hwmod: add names to module MPU IRQ lines
Replace the existing u8 array of module MPU IRQ lines with a struct
that includes a name - similar to the existing struct
omap_hwmod_dma_info. Device drivers can then use
platform_get_resource_byname() to retrieve specific IRQs without nasty
dependencies on array ordering.
Thanks to Benoît Cousson <b-cousson@ti.com> and Kevin Hilman
<khilman@deeprootsystems.com> for feedback on this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Paul Walmsley [Tue, 8 Dec 2009 23:34:15 +0000 (16:34 -0700)]
OMAP3 hwmod: Add automatic OCP_SYSCONFIG AUTOIDLE handling
This patch fills in the OCP_SYSCONFIG.AUTOIDLE handling in the OMAP
hwmod code.
After this patch, the hwmod code will set the module AUTOIDLE bit
(generally <module>.OCP_SYSCONFIG.AUTOIDLE) to 1 by default upon
enable. If the hwmod flag HWMOD_NO_OCP_AUTOIDLE is set, AUTOIDLE will
be set to 0 upon enable. Upon module disable, AUTOIDLE will be set to
1.
Enabling module autoidle should save some power. The only reason to
not set the OCP_SYSCONFIG.AUTOIDLE bit is if there is a bug in the
module RTL, e.g., the MPUINTC block on OMAP3.
Comments from Kevin Hilman <khilman@deeprootsystems.com> inspired this patch,
and Kevin tested an earlier version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Paul Walmsley [Tue, 8 Dec 2009 23:34:14 +0000 (16:34 -0700)]
OMAP3 hwmod: reprogram OCP_SYSCONFIG register after setting SOFTRESET
Reprogram the module's OCP_SYSCONFIG register after module reset (SOFTRESET
= 1). This may not be needed, but the definition of the reset performed by
the SOFTRESET bit is unclear.
Kevin Hilman <khilman@deeprootsystems.com> tested an earlier version of
this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Paul Walmsley [Tue, 8 Dec 2009 23:33:16 +0000 (16:33 -0700)]
OMAP clock/hwmod: fix off-by-one errors
Fix loop bailout off-by-one bugs reported by Juha Leppänen
<juha_motorsportcom@luukku.com>.
This second version incorporates comments from Russell King
<linux@arm.linux.org.uk>. A new macro, 'omap_test_timeout', has
been created, with cleaner code, and existing code has been converted
to use it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Juha Leppänen <juha_motorsportcom@luukku.com>
Cc: Russell King <linux@arm.linux.org.uk>
Thara Gopinath [Tue, 8 Dec 2009 23:33:15 +0000 (16:33 -0700)]
OMAP3: PM: Fix for MPU power domain MEM BANK position
MPU power domain bank 0 bits are displayed in position of bank 1
in PWRSTS and PREPWRSTS registers. So read them from correct
position
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Tue, 8 Dec 2009 23:33:14 +0000 (16:33 -0700)]
OMAP3: SDRC: Place SDRC AC timing and MR changes in CORE DVFS SRAM code behind Kconfig
The code that reprograms the SDRC memory controller during CORE DVFS,
mach-omap2/sram34xx.S:omap3_sram_configure_core_dpll(), does not
ensure that all L3 initiators are prevented from accessing the SDRAM
before modifying the SDRC AC timing and MR registers. This can cause
memory to be corrupted or cause the SDRC to enter an unpredictable
state. This patch places that code behind a Kconfig option,
CONFIG_OMAP3_SDRC_AC_TIMING for now, and adds a note explaining what
is going on. Ideally the code can be added back in once supporting
code is present to ensure that other initiators aren't touching the
SDRAM. At the very least, these registers should be reprogrammable
during kernel init to deal with buggy bootloaders. Users who know
that all other system initiators will not be touching the SDRAM can
also re-enable this Kconfig option.
This is a modification of a patch originally written by Rajendra Nayak
<rnayak@ti.com> (the original is at http://patchwork.kernel.org/patch/51927/).
Rather than removing the code completely, this patch just comments it out.
Thanks to Benoît Cousson <b-cousson@ti.com> and Christophe Sucur
<c-sucur@ti.com> for explaining the technical basis for this and for
explaining what can be done to make this path work in future code.
Thanks to Richard Woodruff <r-woodruff2@ti.com>, Nishanth Menon
<nm@ti.com>, and Olof Johansson <olof@lixom.net> for their comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Christophe Sucur <c-sucur@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Olof Johansson <olof@lixom.net>
Roel Kluin [Tue, 8 Dec 2009 23:33:13 +0000 (16:33 -0700)]
OMAP2/3 powerdomain: return errors rather than returning the output of IS_ERR()
IS_ERR returns only 1 or 0, and the functions return a negative error
in other cases anyways.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Tue, 8 Dec 2009 23:33:13 +0000 (16:33 -0700)]
OMAP powerdomain: rearrange struct powerdomain to save some memory
This patch rearranges the order of structure members in struct powerdomain
to avoid wasting memory due to alignment restrictions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Tue, 8 Dec 2009 23:33:12 +0000 (16:33 -0700)]
OMAP powerdomain/PM: use symbolic constants for the max number of power states
Replace some bare constants with power states.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Paul Walmsley [Tue, 8 Dec 2009 23:33:11 +0000 (16:33 -0700)]
OMAP clockdomain/powerdomain: optimize out sleepdep code on OMAP24xx
OMAP24xx chips don't support software-configurable sleep dependencies.
Test early for this so the compiler can redact the entire function body
on OMAP24xx.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Tue, 8 Dec 2009 23:33:10 +0000 (16:33 -0700)]
OMAP clockdomain/powerdomain: remove CONFIG_OMAP_DEBUG_{CLOCK,POWER}DOMAIN
Avoid cluttering the Kconfig space with debug options that are rarely
used. These can now be enabled and disabled by patching the "#undef DEBUG"
in the source files with "#define DEBUG", conforming to the practice for
the rest of the linux-omap code.
Also, while we're here, some lines in plat-omap/Kconfig use sets of
leading spaces when those lines should start with tabs. Convert most
of them to use tabs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Tue, 8 Dec 2009 23:33:09 +0000 (16:33 -0700)]
OMAP2/3 PRCM: don't export prm_*(), cm_*() functions
Device drivers and loadable modules should not be calling these
prm_* and cm_* functions, so stop exporting them. Only core code
and device driver integration code (in arch/arm/*omap*) should
call these functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Tue, 8 Dec 2009 23:29:38 +0000 (16:29 -0700)]
OMAP1 clock: convert mach-omap1/clock.h to mach-omap1/clock_data.c
The OMAP1 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=
125967425908895&w=2
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the mpu_rate data structures out into their own
files, opp.h and opp_data.c. In the long run, these mpu_rate tables
should be replaced with OPP code.
Also includes a patch from Felipe Balbi <felipe.balbi@nokia.com> to
mark omap1_clk_functions as __initdata to avoid a section warning:
http://patchwork.kernel.org/patch/64366/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Nishanth Menon <nm@ti.com>
Paul Walmsley [Tue, 8 Dec 2009 23:29:37 +0000 (16:29 -0700)]
OMAP1 clock: convert test in disable_unused() to use ENABLE_ON_INIT
mach-omap1/clock.c:omap1_clk_disable_unused() contains a test that
assumes that the clock structures are available in the file's
namespace. After a following patch, this will no longer be the case.
So we need to reimplement that test. It turns out that we already
have a facility in the clock framework to handle this case - the
ENABLE_ON_INIT flag - used on OMAP2/3. Remove the offending test and
mark the clocks that it was intended to catch as ENABLE_ON_INIT.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Linus Torvalds [Fri, 11 Dec 2009 23:59:23 +0000 (15:59 -0800)]
Merge branch 'next' of git://git./linux/kernel/git/davej/cpufreq
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[ACPI/CPUFREQ] Introduce bios_limit per cpu cpufreq sysfs interface
[CPUFREQ] make internal cpufreq_add_dev_* static
[CPUFREQ] use an enum for speedstep processor identification
[CPUFREQ] Document units for transition latency
[CPUFREQ] Use global sysfs cpufreq structure for conservative governor tunings
[CPUFREQ] Documentation: ABI: /sys/devices/system/cpu/cpu#/cpufreq/
[CPUFREQ] powernow-k6: set transition latency value so ondemand governor can be used
[CPUFREQ] cpumask: don't put a cpumask on the stack in x86...cpufreq/powernow-k8.c
Greg Kroah-Hartman [Fri, 11 Dec 2009 23:40:17 +0000 (15:40 -0800)]
Staging: batman: fix debug Kconfig option
The debug batman option needs to depend on the correct
config option.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ "No means no!" - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 11 Dec 2009 23:34:40 +0000 (15:34 -0800)]
Merge git://git./linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (58 commits)
tty: split the lock up a bit further
tty: Move the leader test in disassociate
tty: Push the bkl down a bit in the hangup code
tty: Push the lock down further into the ldisc code
tty: push the BKL down into the handlers a bit
tty: moxa: split open lock
tty: moxa: Kill the use of lock_kernel
tty: moxa: Fix modem op locking
tty: moxa: Kill off the throttle method
tty: moxa: Locking clean up
tty: moxa: rework the locking a bit
tty: moxa: Use more tty_port ops
tty: isicom: fix deadlock on shutdown
tty: mxser: Use the new locking rules to fix setserial properly
tty: mxser: use the tty_port_open method
tty: isicom: sort out the board init logic
tty: isicom: switch to the new tty_port_open helper
tty: tty_port: Add a kref object to the tty port
tty: istallion: tty port open/close methods
tty: stallion: Convert to the tty_port_open/close methods
...
Linus Torvalds [Fri, 11 Dec 2009 23:31:13 +0000 (15:31 -0800)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (21 commits)
ext3: PTR_ERR return of wrong pointer in setup_new_group_blocks()
ext3: Fix data / filesystem corruption when write fails to copy data
ext4: Support for 64-bit quota format
ext3: Support for vfsv1 quota format
quota: Implement quota format with 64-bit space and inode limits
quota: Move definition of QFMT_OCFS2 to linux/quota.h
ext2: fix comment in ext2_find_entry about return values
ext3: Unify log messages in ext3
ext2: clear uptodate flag on super block I/O error
ext2: Unify log messages in ext2
ext3: make "norecovery" an alias for "noload"
ext3: Don't update the superblock in ext3_statfs()
ext3: journal all modifications in ext3_xattr_set_handle
ext2: Explicitly assign values to on-disk enum of filetypes
quota: Fix WARN_ON in lookup_one_len
const: struct quota_format_ops
ubifs: remove manual O_SYNC handling
afs: remove manual O_SYNC handling
kill wait_on_page_writeback_range
vfs: Implement proper O_SYNC semantics
...
Linus Torvalds [Fri, 11 Dec 2009 23:30:29 +0000 (15:30 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: Fix error return for fallocate() on XFS
xfs: cleanup dmapi macros in the umount path
xfs: remove incorrect sparse annotation for xfs_iget_cache_miss
xfs: kill the STATIC_INLINE macro
xfs: uninline xfs_get_extsz_hint
xfs: rename xfs_attr_fetch to xfs_attr_get_int
xfs: simplify xfs_buf_get / xfs_buf_read interfaces
xfs: remove IO_ISAIO
xfs: Wrapped journal record corruption on read at recovery
xfs: cleanup data end I/O handlers
xfs: use WRITE_SYNC_PLUG for synchronous writeout
xfs: reset the i_iolock lock class in the reclaim path
xfs: I/O completion handlers must use NOFS allocations
xfs: fix mmap_sem/iolock inversion in xfs_free_eofblocks
xfs: simplify inode teardown
Linus Torvalds [Fri, 11 Dec 2009 23:25:56 +0000 (15:25 -0800)]
Merge git://git./linux/kernel/git/gregkh/staging-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (235 commits)
Staging: IIO: add selection of IIO_SW_RING to LIS3L02DQ as needed
Staging: IIO: Add tsl2560-2 support to tsl2563 driver.
Staging: IIO: Remove tsl2561 driver. Support merged with tsl2563.
Staging: wlags49_h2: fix up signal levels
+ drivers-staging-wlags49_h2-remove-cvs-metadata.patch added to -mm tree
Staging: samsung-laptop: add TODO file
Staging: samsung-laptop: remove old kernel code
Staging: add Samsung Laptop driver
staging: batman-adv meshing protocol
Staging: rtl8192u: depends on USB
Staging: rtl8192u: remove dead code
Staging: rtl8192u: remove bad whitespaces
Staging: rtl8192u: make it compile
Staging: Added Realtek rtl8192u driver to staging
Staging: dream: add gpio and pmem support
Staging: dream: add TODO file
Staging: android: delete android drivers
Staging: et131x: clean up the avail fields in the rx registers
Staging: et131x: Clean up number fields
Staging: et131x: kill RX_DMA_MAX_PKT_TIME
...
Linus Torvalds [Fri, 11 Dec 2009 23:24:56 +0000 (15:24 -0800)]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (27 commits)
Driver core: fix race in dev_driver_string
Driver Core: Early platform driver buffer
sysfs: sysfs_setattr remove unnecessary permission check.
sysfs: Factor out sysfs_rename from sysfs_rename_dir and sysfs_move_dir
sysfs: Propagate renames to the vfs on demand
sysfs: Gut sysfs_addrm_start and sysfs_addrm_finish
sysfs: In sysfs_chmod_file lazily propagate the mode change.
sysfs: Implement sysfs_getattr & sysfs_permission
sysfs: Nicely indent sysfs_symlink_inode_operations
sysfs: Update s_iattr on link and unlink.
sysfs: Fix locking and factor out sysfs_sd_setattr
sysfs: Simplify iattr time assignments
sysfs: Simplify sysfs_chmod_file semantics
sysfs: Use dentry_ops instead of directly playing with the dcache
sysfs: Rename sysfs_d_iput to sysfs_dentry_iput
sysfs: Update sysfs_setxattr so it updates secdata under the sysfs_mutex
debugfs: fix create mutex racy fops and private data
Driver core: Don't remove kobjects in device_shutdown.
firmware_class: make request_firmware_nowait more useful
Driver-Core: devtmpfs - set root directory mode to 0755
...
Linus Torvalds [Fri, 11 Dec 2009 23:22:55 +0000 (15:22 -0800)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (122 commits)
USB: mos7840: add device IDs for B&B electronics devices
USB: ftdi_sio: add USB device ID's for B&B Electronics line
USB: musb: musb_host: fix sparse warning
USB: musb: musb_gadget: fix sparse warning
USB: musb: omap2430: fix sparse warning
USB: core: message: fix sparse warning
USB: core: hub: fix sparse warning
USB: core: fix sparse warning for static function
USB: Added USB_ETH_RNDIS to use instead of CONFIG_USB_ETH_RNDIS
USB: Check bandwidth when switching alt settings.
USB: Refactor code to find alternate interface settings.
USB: xhci: Fix command completion after a drop endpoint.
USB: xhci: Make reverting an alt setting "unfailable".
USB: usbtmc: Use usb_clear_halt() instead of custom code.
USB: xhci: Add correct email and files to MAINTAINERS entry.
USB: ehci-omap.c: introduce missing kfree
USB: xhci-mem.c: introduce missing kfree
USB: add remove_id sysfs attr for usb drivers
USB: g_multi kconfig: fix depends and help text
USB: option: add pid for ZTE
...
Linus Torvalds [Fri, 11 Dec 2009 23:22:27 +0000 (15:22 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: handle receive packets with a data length of zero
Linus Torvalds [Fri, 11 Dec 2009 23:19:56 +0000 (15:19 -0800)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jwessel/linux-2.6-kgdb
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: Always process the whole breakpoint list on activate or deactivate
kgdb: continue and warn on signal passing from gdb
kgdb,x86: do not set kgdb_single_step on x86
kgdb: allow for cpu switch when single stepping
kgdb,i386: Fix corner case access to ss with NMI watch dog exception
kgdb: Replace strstr() by strchr() for single-character needles
kgdbts: Read buffer overflow
kgdb: Read buffer overflow
kgdb,x86: remove redundant test