OSDN Git Service
Christoph Hellwig [Tue, 3 Oct 2017 08:47:00 +0000 (10:47 +0200)]
block: move __elv_next_request to blk-core.c
No need to have this helper inline in a header. Also drop the __ prefix.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Paolo Valente [Thu, 21 Sep 2017 09:04:03 +0000 (11:04 +0200)]
block, bfq: decrease burst size when queues in burst exit
If many queues belonging to the same group happen to be created
shortly after each other, then the concurrent processes associated
with these queues have typically a common goal, and they get it done
as soon as possible if not hampered by device idling. Examples are
processes spawned by git grep, or by systemd during boot. As for
device idling, this mechanism is currently necessary for weight
raising to succeed in its goal: privileging I/O. In view of these
facts, BFQ does not provide the above queues with either weight
raising or device idling.
On the other hand, a burst of queue creations may be caused also by
the start-up of a complex application. In this case, these queues need
usually to be served one after the other, and as quickly as possible,
to maximise responsiveness. Therefore, in this case the best strategy
is to weight-raise all the queues created during the burst, i.e., the
exact opposite of the strategy for the above case.
To distinguish between the two cases, BFQ uses an empirical burst-size
threshold, found through extensive tests and monitoring of daily
usage. Only large bursts, i.e., burst with a size above this
threshold, are considered as generated by a high number of parallel
processes. In this respect, upstart-based boot proved to be rather
hard to detect as generating a large burst of queue creations, because
with upstart most of the queues created in a burst exit *before* the
next queues in the same burst are created. To address this issue, I
changed the burst-detection mechanism so as to not decrease the size
of the current burst even if one of the queues in the burst is
eliminated.
Unfortunately, this missing decrease causes false positives on very
fast systems: on the start-up of a complex application, such as
libreoffice writer, so many queues are created, served and exited
shortly after each other, that a large burst of queue creations is
wrongly detected as occurring. These false positives just disappear if
the size of a burst is decreased when one of the queues in the burst
exits. This commit restores the missing burst-size decrease, relying
of the fact that upstart is apparently unlikely to be used on systems
running this and future versions of the kernel.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Mauro Andreolini <mauro.andreolini@unimore.it>
Signed-off-by: Angelo Ruocco <angeloruocco90@gmail.com>
Tested-by: Mirko Montanari <mirkomontanari91@gmail.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Lee Tibbert <lee.tibbert@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Paolo Valente [Thu, 21 Sep 2017 09:04:02 +0000 (11:04 +0200)]
block, bfq: let early-merged queues be weight-raised on split too
A just-created bfq_queue, say Q, may happen to be merged with another
bfq_queue on the very first invocation of the function
__bfq_insert_request. In such a case, even if Q would clearly deserve
interactive weight raising (as it has just been created), the function
bfq_add_request does not make it to be invoked for Q, and thus to
activate weight raising for Q. As a consequence, when the state of Q
is saved for a possible future restore, after a split of Q from the
other bfq_queue(s), such a state happens to be (unjustly)
non-weight-raised. Then the bfq_queue will not enjoy any weight
raising on the split, even if should still be in an interactive
weight-raising period when the split occurs.
This commit solves this problem as follows, for a just-created
bfq_queue that is being early-merged: it stores directly, in the saved
state of the bfq_queue, the weight-raising state that would have been
assigned to the bfq_queue if not early-merged.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Tested-by: Angelo Ruocco <angeloruocco90@gmail.com>
Tested-by: Mirko Montanari <mirkomontanari91@gmail.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Lee Tibbert <lee.tibbert@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Paolo Valente [Thu, 21 Sep 2017 09:04:01 +0000 (11:04 +0200)]
block, bfq: check and switch back to interactive wr also on queue split
As already explained in the message of commit "block, bfq: fix
wrong init of saved start time for weight raising", if a soft
real-time weight-raising period happens to be nested in a larger
interactive weight-raising period, then BFQ restores the interactive
weight raising at the end of the soft real-time weight raising. In
particular, BFQ checks whether the latter has ended only on request
dispatches.
Unfortunately, the above scheme fails to restore interactive weight
raising in the following corner case: if a bfq_queue, say Q,
1) Is merged with another bfq_queue while it is in a nested soft
real-time weight-raising period. The weight-raising state of Q is
then saved, and not considered any longer until a split occurs.
2) Is split from the other bfq_queue(s) at a time instant when its
soft real-time weight raising is already finished.
On the split, while resuming the previous, soft real-time
weight-raised state of the bfq_queue Q, BFQ checks whether the
current soft real-time weight-raising period is actually over. If so,
BFQ switches weight raising off for Q, *without* checking whether the
soft real-time period was actually nested in a non-yet-finished
interactive weight-raising period.
This commit addresses this issue by adding the above missing check in
bfq_queue splits, and restoring interactive weight raising if needed.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Tested-by: Angelo Ruocco <angeloruocco90@gmail.com>
Tested-by: Mirko Montanari <mirkomontanari91@gmail.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Lee Tibbert <lee.tibbert@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Paolo Valente [Thu, 21 Sep 2017 09:04:00 +0000 (11:04 +0200)]
block, bfq: fix wrong init of saved start time for weight raising
This commit fixes a bug that causes bfq to fail to guarantee a high
responsiveness on some drives, if there is heavy random read+write I/O
in the background. More precisely, such a failure allowed this bug to
be found [1], but the bug may well cause other yet unreported
anomalies.
BFQ raises the weight of the bfq_queues associated with soft real-time
applications, to privilege the I/O, and thus reduce latency, for these
applications. This mechanism is named soft-real-time weight raising in
BFQ. A soft real-time period may happen to be nested into an
interactive weight raising period, i.e., it may happen that, when a
bfq_queue switches to a soft real-time weight-raised state, the
bfq_queue is already being weight-raised because deemed interactive
too. In this case, BFQ saves in a special variable
wr_start_at_switch_to_srt, the time instant when the interactive
weight-raising period started for the bfq_queue, i.e., the time
instant when BFQ started to deem the bfq_queue interactive. This value
is then used to check whether the interactive weight-raising period
would still be in progress when the soft real-time weight-raising
period ends. If so, interactive weight raising is restored for the
bfq_queue. This restore is useful, in particular, because it prevents
bfq_queues from losing their interactive weight raising prematurely,
as a consequence of spurious, short-lived soft real-time
weight-raising periods caused by wrong detections as soft real-time.
If, instead, a bfq_queue switches to soft-real-time weight raising
while it *is not* already in an interactive weight-raising period,
then the variable wr_start_at_switch_to_srt has no meaning during the
following soft real-time weight-raising period. Unfortunately the
handling of this case is wrong in BFQ: not only the variable is not
flagged somehow as meaningless, but it is also set to the time when
the switch to soft real-time weight-raising occurs. This may cause an
interactive weight-raising period to be considered mistakenly as still
in progress, and thus a spurious interactive weight-raising period to
start for the bfq_queue, at the end of the soft-real-time
weight-raising period. In particular the spurious interactive
weight-raising period will be considered as still in progress, if the
soft-real-time weight-raising period does not last very long. The
bfq_queue will then be wrongly privileged and, if I/O bound, will
unjustly steal bandwidth to truly interactive or soft real-time
bfq_queues, harming responsiveness and low latency.
This commit fixes this issue by just setting wr_start_at_switch_to_srt
to minus infinity (farthest past time instant according to jiffies
macros): when the soft-real-time weight-raising period ends, certainly
no interactive weight-raising period will be considered as still in
progress.
[1] Background I/O Type: Random - Background I/O mix: Reads and writes
- Application to start: LibreOffice Writer in
http://www.phoronix.com/scan.php?page=news_item&px=Linux-4.13-IO-Laptop
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Angelo Ruocco <angeloruocco90@gmail.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Lee Tibbert <lee.tibbert@gmail.com>
Tested-by: Mirko Montanari <mirkomontanari91@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Thu, 28 Sep 2017 17:31:55 +0000 (11:31 -0600)]
writeback: only allow one inflight and pending full flush
When someone calls wakeup_flusher_threads() or
wakeup_flusher_threads_bdi(), they schedule writeback of all dirty
pages in the system (or on that bdi). If we are tight on memory, we
can get tons of these queued from kswapd/vmscan. This causes (at
least) two problems:
1) We consume a ton of memory just allocating writeback work items.
We've seen as much as 600 million of these writeback work items
pending. That's a lot of memory to pointlessly hold hostage,
while the box is under memory pressure.
2) We spend so much time processing these work items, that we
introduce a softlockup in writeback processing. This is because
each of the writeback work items don't end up doing any work (it's
hard when you have millions of identical ones coming in to the
flush machinery), so we just sit in a tight loop pulling work
items and deleting/freeing them.
Fix this by adding a 'start_all' bit to the writeback structure, and
set that when someone attempts to flush all dirty pages. The bit is
cleared when we start writeback on that work item. If the bit is
already set when we attempt to queue !nr_pages writeback, then we
simply ignore it.
This provides us one full flush in flight, with one pending as well,
and makes for more efficient handling of this type of writeback.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Chris Mason <clm@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Thu, 28 Sep 2017 17:31:22 +0000 (11:31 -0600)]
writeback: move nr_pages == 0 logic to one location
Now that we have no external callers of wb_start_writeback(), we
can shuffle the passing in of 'nr_pages'. Everybody passes in 0
at this point, so just kill the argument and move the dirty
count retrieval to that function.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Chris Mason <clm@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Thu, 28 Sep 2017 17:28:55 +0000 (11:28 -0600)]
writeback: make wb_start_writeback() static
We don't have any callers outside of fs-writeback.c anymore,
make it private.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Chris Mason <clm@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Thu, 28 Sep 2017 17:28:02 +0000 (11:28 -0600)]
writeback: pass in '0' for nr_pages writeback in laptop mode
Laptop mode really wants to writeback the number of dirty
pages and inodes. Instead of calculating this in the caller,
just pass in 0 and let wakeup_flusher_threads() handle it.
Use the new wakeup_flusher_threads_bdi() instead of rolling
our own.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Chris Mason <clm@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Thu, 28 Sep 2017 17:26:59 +0000 (11:26 -0600)]
writeback: provide a wakeup_flusher_threads_bdi()
Similar to wakeup_flusher_threads(), except that we only wake
up the flusher threads on the specified backing device.
No functional changes in this patch.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Chris Mason <clm@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Thu, 28 Sep 2017 17:25:03 +0000 (11:25 -0600)]
writeback: remove 'range_cyclic' argument for wb_start_writeback()
All the callers pass in 'true' for range_cyclic, so kill the
argument.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Wed, 27 Sep 2017 19:28:18 +0000 (13:28 -0600)]
writeback: switch wakeup_flusher_threads() to cyclic writeback
We're writing back the full range of dirty pages on the devices,
there's no point in making this special and not do normal range
cyclic writeback.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Wed, 20 Sep 2017 14:58:25 +0000 (08:58 -0600)]
fs: kill 'nr_pages' argument from wakeup_flusher_threads()
Everybody is passing in 0 now, let's get rid of the argument.
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Wed, 27 Sep 2017 12:08:57 +0000 (06:08 -0600)]
buffer: eliminate the need to call free_more_memory() in __getblk_slow()
Since the previous commit removed any case where grow_buffers()
would return failure due to memory allocations, we can safely
remove the case where we have to call free_more_memory() in
this function.
Since this is also the last user of free_more_memory(), kill
it off completely.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Wed, 27 Sep 2017 11:45:36 +0000 (05:45 -0600)]
buffer: grow_dev_page() should use __GFP_NOFAIL for all cases
We currently use it for find_or_create_page(), which means that it
cannot fail. Ensure we also pass in 'retry == true' to
alloc_page_buffers(), which also ensure that it cannot fail.
After this, there are no failure cases in grow_dev_page() that
occur because of a failed memory allocation.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Wed, 27 Sep 2017 11:40:16 +0000 (05:40 -0600)]
buffer: have alloc_page_buffers() use __GFP_NOFAIL
Instead of adding weird retry logic in that function, utilize
__GFP_NOFAIL to ensure that the vm takes care of handling any
potential retries appropriately. This means we don't have to
call free_more_memory() from here.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Sat, 30 Sep 2017 08:08:24 +0000 (02:08 -0600)]
blk-mq: wire up completion notifier for laptop mode
For some reason, the laptop mode IO completion notified was never wired
up for blk-mq. Ensure that we trigger the callback appropriately, to arm
the laptop mode flush timer.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Sun, 1 Oct 2017 07:26:21 +0000 (01:26 -0600)]
blk-mq-tag: kill unused tag enums
We don't have any notion of a tagging cache anymore, and haven't
for a long time. Kill off the unused enums.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
weiping zhang [Sat, 30 Sep 2017 07:01:48 +0000 (15:01 +0800)]
blk-mq: remove unused function hctx_allow_merges
since
9bddeb2a5b981 "blk-mq: make per-sw-queue bio merge as default .bio_merge"
there is no caller for this function.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
weiping zhang [Sat, 30 Sep 2017 01:49:21 +0000 (09:49 +0800)]
null_blk: add "no_sched" module parameter
add an option that disable io scheduler for null block device.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Shaohua Li [Tue, 26 Sep 2017 18:02:12 +0000 (11:02 -0700)]
block: fix a build error
The code is only for blkcg not for all cgroups
Fixes:
d4478e92d618 ("block/loop: make loop cgroup aware")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Corentin Labbe [Mon, 25 Sep 2017 17:10:07 +0000 (19:10 +0200)]
block: cryptoloop - Fix build warning
This patch fix the following build warning:
drivers/block/cryptoloop.c:46:8: warning: variable 'cipher' set but not used [-Wunused-but-set-variable]
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Shaohua Li [Mon, 25 Sep 2017 19:07:22 +0000 (13:07 -0600)]
block/loop: make loop cgroup aware
loop block device handles IO in a separate thread. The actual IO
dispatched isn't cloned from the IO loop device received, so the
dispatched IO loses the cgroup context.
I'm ignoring buffer IO case now, which is quite complicated. Making the
loop thread aware cgroup context doesn't really help. The loop device
only writes to a single file. In current writeback cgroup
implementation, the file can only belong to one cgroup.
For direct IO case, we could workaround the issue in theory. For
example, say we assign cgroup1 5M/s BW for loop device and cgroup2
10M/s. We can create a special cgroup for loop thread and assign at
least 15M/s for the underlayer disk. In this way, we correctly throttle
the two cgroups. But this is tricky to setup.
This patch tries to address the issue. We record bio's css in loop
command. When loop thread is handling the command, we then use the API
provided in patch 1 to set the css for current task. The bio layer will
use the css for new IO (from patch 3).
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Shaohua Li [Thu, 14 Sep 2017 21:02:06 +0000 (14:02 -0700)]
block: make blkcg aware of kthread stored original cgroup info
bio_blkcg is the only API to get cgroup info for a bio right now. If
bio_blkcg finds current task is a kthread and has original blkcg
associated, it will use the css instead of associating the bio to
current task. This makes it possible that kthread dispatches bios on
behalf of other threads.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Shaohua Li [Thu, 14 Sep 2017 21:02:05 +0000 (14:02 -0700)]
blkcg: delete unused APIs
Nobody uses the APIs right now.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Shaohua Li [Thu, 14 Sep 2017 21:02:04 +0000 (14:02 -0700)]
kthread: add a mechanism to store cgroup info
kthread usually runs jobs on behalf of other threads. The jobs should be
charged to cgroup of original threads. But the jobs run in a kthread,
where we lose the cgroup context of original threads. The patch adds a
machanism to record cgroup info of original threads in kthread context.
Later we can retrieve the cgroup info and attach the cgroup info to jobs.
Since this mechanism is only required by kthread, we store the cgroup
info in kthread data instead of generic task_struct.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Tue, 26 Sep 2017 01:24:14 +0000 (18:24 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull compat fix from Al Viro:
"I really wish gcc warned about conversions from pointer to function
into void *..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a typo in put_compat_shm_info()
Al Viro [Tue, 26 Sep 2017 00:38:45 +0000 (20:38 -0400)]
fix a typo in put_compat_shm_info()
"uip" misspelled as "up"; unfortunately, the latter happens to be
a function and gcc is happy to convert it to void *...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Mon, 25 Sep 2017 22:46:04 +0000 (15:46 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Two sets of NVMe pull requests from Christoph:
- Fixes for the Fibre Channel host/target to fix spec compliance
- Allow a zero keep alive timeout
- Make the debug printk for broken SGLs work better
- Fix queue zeroing during initialization
- Set of RDMA and FC fixes
- Target div-by-zero fix
- bsg double-free fix.
- ndb unknown ioctl fix from Josef.
- Buffered vs O_DIRECT page cache inconsistency fix. Has been floating
around for a long time, well reviewed. From Lukas.
- brd overflow fix from Mikulas.
- Fix for a loop regression in this merge window, where using a union
for two members of the loop_cmd turned out to be a really bad idea.
From Omar.
- Fix for an iostat regression fix in this series, using the wrong API
to get at the block queue. From Shaohua.
- Fix for a potential blktrace delection deadlock. From Waiman.
* 'for-linus' of git://git.kernel.dk/linux-block: (30 commits)
nvme-fcloop: fix port deletes and callbacks
nvmet-fc: sync header templates with comments
nvmet-fc: ensure target queue id within range.
nvmet-fc: on port remove call put outside lock
nvme-rdma: don't fully stop the controller in error recovery
nvme-rdma: give up reconnect if state change fails
nvme-core: Use nvme_wq to queue async events and fw activation
nvme: fix sqhd reference when admin queue connect fails
block: fix a crash caused by wrong API
fs: Fix page cache inconsistency when mixing buffered and AIO DIO
nvmet: implement valid sqhd values in completions
nvme-fabrics: Allow 0 as KATO value
nvme: allow timed-out ios to retry
nvme: stop aer posting if controller state not live
nvme-pci: Print invalid SGL only once
nvme-pci: initialize queue memory before interrupts
nvmet-fc: fix failing max io queue connections
nvme-fc: use transport-specific sgl format
nvme: add transport SGL definitions
nvme.h: remove FC transport-specific error values
...
Linus Torvalds [Mon, 25 Sep 2017 22:41:56 +0000 (15:41 -0700)]
Merge tag 'gfs2-for-linus-4.14-rc3' of git://git./linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fix from Bob Peterson:
"GFS2: Fix an old regression in GFS2's debugfs interface
This fixes a regression introduced by commit
88ffbf3e037e ("GFS2: Use
resizable hash table for glocks"). The regression caused the glock dump
in debugfs to not report all the glocks, which makes debugging
extremely difficult"
* tag 'gfs2-for-linus-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix debugfs glocks dump
Linus Torvalds [Mon, 25 Sep 2017 22:37:19 +0000 (15:37 -0700)]
Merge tag 'microblaze-4.14-rc3' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze fixes from Michal Simek:
- Kbuild fix
- use vma_pages
- setup default little endians
* tag 'microblaze-4.14-rc3' of git://git.monstr.eu/linux-2.6-microblaze:
arch: change default endian for microblaze
microblaze: Cocci spatch "vma_pages"
microblaze: Add missing kvm_para.h to Kbuild
Linus Torvalds [Mon, 25 Sep 2017 22:22:31 +0000 (15:22 -0700)]
Merge tag 'trace-v4.14-rc1-2' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Stack tracing and RCU has been having issues with each other and
lockdep has been pointing out constant problems.
The changes have been going into the stack tracer, but it has been
discovered that the problem isn't with the stack tracer itself, but it
is with calling save_stack_trace() from within the internals of RCU.
The stack tracer is the one that can trigger the issue the easiest,
but examining the problem further, it could also happen from a WARN()
in the wrong place, or even if an NMI happened in this area and it did
an rcu_read_lock().
The critical area is where RCU is not watching. Which can happen while
going to and from idle, or bringing up or taking down a CPU.
The final fix was to put the protection in kernel_text_address() as it
is the one that requires RCU to be watching while doing the stack
trace.
To make this work properly, Paul had to allow rcu_irq_enter() happen
after rcu_nmi_enter(). This should have been done anyway, since an NMI
can page fault (reading vmalloc area), and a page fault triggers
rcu_irq_enter().
One patch is just a consolidation of code so that the fix only needed
to be done in one location"
* tag 'trace-v4.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove RCU work arounds from stack tracer
extable: Enable RCU if it is not watching in kernel_text_address()
extable: Consolidate *kernel_text_address() functions
rcu: Allow for page faults in NMI handlers
James Smart [Tue, 19 Sep 2017 21:01:50 +0000 (14:01 -0700)]
nvme-fcloop: fix port deletes and callbacks
Now that there are potentially long delays between when a remoteport or
targetport delete calls is made and when the callback occurs (dev_loss_tmo
timeout), no longer block in the delete routines and move the final nport
puts to the callbacks.
Moved the fcloop_nport_get/put/free routines to avoid forward declarations.
Ensure port_info structs used in registrations are nulled in case fields
are not set (ex: devloss_tmo values).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Wed, 20 Sep 2017 18:07:26 +0000 (11:07 -0700)]
nvmet-fc: sync header templates with comments
Comments were incorrect:
- defer_rcv was in host port template. moved to target port template
- Added Mandatory statements for target port template items
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Tue, 19 Sep 2017 23:33:56 +0000 (16:33 -0700)]
nvmet-fc: ensure target queue id within range.
When searching for queue id's ensure they are within the expected range.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Tue, 19 Sep 2017 22:13:11 +0000 (15:13 -0700)]
nvmet-fc: on port remove call put outside lock
Avoid calling the put routine, as it may traverse to free routines while
holding the target lock.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sagi Grimberg [Thu, 21 Sep 2017 14:01:38 +0000 (17:01 +0300)]
nvme-rdma: don't fully stop the controller in error recovery
By calling nvme_stop_ctrl on a already failed controller will wait for the
scan work to complete (only by identify timeout expiration which is 60
seconds). This is unnecessary when we already know that the controller has
failed.
Reported-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sagi Grimberg [Thu, 21 Sep 2017 14:01:37 +0000 (17:01 +0300)]
nvme-rdma: give up reconnect if state change fails
If we failed to transition to state LIVE after a successful reconnect,
then controller deletion already started. In this case there is no
point moving forward with reconnect.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sagi Grimberg [Thu, 21 Sep 2017 14:01:36 +0000 (17:01 +0300)]
nvme-core: Use nvme_wq to queue async events and fw activation
async_event_work might race as it is executed from two different
workqueues at the moment.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 21 Sep 2017 15:13:49 +0000 (08:13 -0700)]
nvme: fix sqhd reference when admin queue connect fails
Fix bug in sqhd patch.
It wasn't the sq that was at risk. In the case where the admin queue
connect command fails, the sq->size field is not set. Therefore, this
becomes a divide by zero error.
Add a quick check to bypass under this failure condition.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Andreas Gruenbacher [Tue, 19 Sep 2017 12:15:35 +0000 (07:15 -0500)]
gfs2: Fix debugfs glocks dump
The switch to rhashtables (commit
88ffbf3e03) broke the debugfs glock
dump (/sys/kernel/debug/gfs2/<device>/glocks) for dumps bigger than a
single buffer: the right function for restarting an rhashtable iteration
from the beginning of the hash table is rhashtable_walk_enter;
rhashtable_walk_stop + rhashtable_walk_start will just resume from the
current position.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Cc: stable@vger.kernel.org # v4.3+
Shaohua Li [Thu, 21 Sep 2017 19:17:16 +0000 (12:17 -0700)]
block: fix a crash caused by wrong API
part_stat_show takes a part device not a disk, so we should use
part_to_disk.
Fixes:
d62e26b3ffd2("block: pass in queue to inflight accounting")
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Omar Sandoval <osandov@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Lukas Czerner [Thu, 21 Sep 2017 14:16:29 +0000 (08:16 -0600)]
fs: Fix page cache inconsistency when mixing buffered and AIO DIO
Currently when mixing buffered reads and asynchronous direct writes it
is possible to end up with the situation where we have stale data in the
page cache while the new data is already written to disk. This is
permanent until the affected pages are flushed away. Despite the fact
that mixing buffered and direct IO is ill-advised it does pose a thread
for a data integrity, is unexpected and should be fixed.
Fix this by deferring completion of asynchronous direct writes to a
process context in the case that there are mapped pages to be found in
the inode. Later before the completion in dio_complete() invalidate
the pages in question. This ensures that after the completion the pages
in the written area are either unmapped, or populated with up-to-date
data. Also do the same for the iomap case which uses
iomap_dio_complete() instead.
This has a side effect of deferring the completion to a process context
for every AIO DIO that happens on inode that has pages mapped. However
since the consensus is that this is ill-advised practice the performance
implication should not be a problem.
This was based on proposal from Jeff Moyer, thanks!
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Mon, 18 Sep 2017 16:08:29 +0000 (09:08 -0700)]
nvmet: implement valid sqhd values in completions
To support sqhd, for initiators that are following the spec and
paying attention to sqhd vs their sqtail values:
- add sqhd to struct nvmet_sq
- initialize sqhd to 0 in nvmet_sq_setup
- rather than propagate the 0's-based qsize value from the connect message
which requires a +1 in every sqhd update, and as nothing else references
it, convert to 1's-based value in nvmt_sq/cq_setup() calls.
- validate connect message sqsize being non-zero per spec.
- updated assign sqhd for every completion that goes back.
Also remove handling the NULL sq case in __nvmet_req_complete, as it can't
happen with the current code.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Guilherme G. Piccoli [Thu, 14 Sep 2017 16:59:28 +0000 (13:59 -0300)]
nvme-fabrics: Allow 0 as KATO value
Currently, driver code allows user to set 0 as KATO
(Keep Alive TimeOut), but this is not being respected.
This patch enforces the expected behavior.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 7 Sep 2017 20:18:04 +0000 (13:18 -0700)]
nvme: allow timed-out ios to retry
Currently the nvme_req_needs_retry() applies several checks to see if
a retry is allowed. On of those is whether the current time has exceeded
the start time of the io plus the timeout length. This check, if an io
times out, means there is never a retry allowed for the io. Which means
applications see the io failure.
Remove this check and allow the io to timeout, like it does on other
protocols, and retries to be made.
On the FC transport, a frame can be lost for an individual io, and there
may be no other errors that escalate for the connection/association.
The io will timeout, which causes the transport to escalate into creating
a new association, but the io that timed out, due to this retry logic, has
already failed back to the application and things are hosed.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 14 Sep 2017 18:03:09 +0000 (11:03 -0700)]
nvme: stop aer posting if controller state not live
If an nvme async_event command completes, in most cases, a new
async event is posted. However, if the controller enters a
resetting or reconnecting state, there is nothing to block the
scheduled work element from posting the async event again. Nor are
there calls from the transport to stop async events when an
association dies.
In the case of FC, where the association is torn down, the aer must
be aborted on the FC link and completes through the normal job
completion path. Thus the terminated async event ends up being
rescheduled even though the controller isn't in a valid state for
the aer, and the reposting gets the transport into a partially torn
down data structure.
It's possible to hit the scenario on rdma, although much less likely
due to an aer completing right as the association is terminated and
as the association teardown reclaims the blk requests via
nvme_cancel_request() so its immediate, not a link-related action
like on FC.
Fix by putting controller state checks in both the async event
completion routine where it schedules the async event and in the
async event work routine before it calls into the transport. It's
effectively a "stop_async_events()" behavior. The transport, when
it creates a new association with the subsystem will transition
the state back to live and is already restarting the async event
posting.
Signed-off-by: James Smart <james.smart@broadcom.com>
[hch: remove taking a lock over reading the controller state]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Keith Busch [Fri, 15 Sep 2017 17:05:38 +0000 (13:05 -0400)]
nvme-pci: Print invalid SGL only once
The WARN_ONCE macro returns true if the condition is true, not if the
warn was raised, so we're printing the scatter list every time it's
invalid. This is excessive and makes debugging harder, so this patch
prints it just once.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Keith Busch [Thu, 14 Sep 2017 17:54:39 +0000 (13:54 -0400)]
nvme-pci: initialize queue memory before interrupts
A spurious interrupt before the nvme driver has initialized the completion
queue may inadvertently cause the driver to believe it has a completion
to process. This may result in a NULL dereference since the nvmeq's tags
are not set at this point.
The patch initializes the host's CQ memory so that a spurious interrupt
isn't mistaken for a real completion.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Mon, 11 Sep 2017 23:16:53 +0000 (16:16 -0700)]
nvmet-fc: fix failing max io queue connections
fc transport is treating NVMET_NR_QUEUES as maximum queue count, e.g.
admin queue plus NVMET_NR_QUEUES-1 io queues. But NVMET_NR_QUEUES is
the number of io queues, so maximum queue count is really
NVMET_NR_QUEUES+1.
Fix the handling in the target fc transport
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 7 Sep 2017 20:20:24 +0000 (13:20 -0700)]
nvme-fc: use transport-specific sgl format
Sync with NVM Express spec change and FC-NVME 1.18.
FC transport sets SGL type to Transport SGL Data Block Descriptor and
subtype to transport-specific value 0x0A.
Removed the warn-on's on the PRP fields. They are unneeded. They were
to check for values from the upper layer that weren't set right, and
for the most part were fine. But, with Async events, which reuse the
same structure and 2nd time issued the SGL overlay converted them to
the Transport SGL values - the warn-on's were errantly firing.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 7 Sep 2017 20:20:23 +0000 (13:20 -0700)]
nvme: add transport SGL definitions
Add transport SGL defintions from NVMe TP 4008, required for
the final NVMe-FC standard.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 7 Sep 2017 23:27:25 +0000 (16:27 -0700)]
nvme.h: remove FC transport-specific error values
The NVM express group recinded the reserved range for the transport.
Remove the FC-centric values that had been defined.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 14 Sep 2017 18:30:15 +0000 (11:30 -0700)]
qla2xxx: remove use of FC-specific error codes
The qla2xxx driver uses the FC-specific error when it needed to return an
error to the FC-NVME transport. Convert to use a generic value instead.
Signed-off-by: James Smart <james.smart@broadcom.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 7 Sep 2017 23:27:29 +0000 (16:27 -0700)]
lpfc: remove use of FC-specific error codes
The lpfc driver uses the FC-specific error when it needed to return an
error to the FC-NVME transport. Convert to use a generic value instead.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 7 Sep 2017 23:27:28 +0000 (16:27 -0700)]
nvmet-fcloop: remove use of FC-specific error codes
The FC-NVME transport loopback test module used the FC-specific error
codes in cases where it emulated a transport abort case. Instead of
using the FC-specific values, now use a generic value (NVME_SC_INTERNAL).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 7 Sep 2017 23:27:27 +0000 (16:27 -0700)]
nvmet-fc: remove use of FC-specific error codes
The FC-NVME target transport used the FC-specific error codes in
return codes when the transport or lldd failed. Instead of using the
FC-specific values, now use a generic value (NVME_SC_INTERNAL).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
James Smart [Thu, 7 Sep 2017 23:27:26 +0000 (16:27 -0700)]
nvme-fc: remove use of FC-specific error codes
The FC-NVME transport used the FC-specific error codes in cases where
it had to fabricate an error to go back up stack. Instead of using the
FC-specific values, now use a generic value (NVME_SC_INTERNAL).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Omar Sandoval [Wed, 20 Sep 2017 21:24:34 +0000 (14:24 -0700)]
loop: remove union of use_aio and ref in struct loop_cmd
When the request is completed, lo_complete_rq() checks cmd->use_aio.
However, if this is in fact an aio request, cmd->use_aio will have
already been reused as cmd->ref by lo_rw_aio*. Fix it by not using a
union. On x86_64, there's a hole after the union anyways, so this
doesn't make struct loop_cmd any bigger.
Fixes:
92d773324b7e ("block/loop: fix use after free")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Waiman Long [Wed, 20 Sep 2017 19:12:20 +0000 (13:12 -0600)]
blktrace: Fix potential deadlock between delete & sysfs ops
The lockdep code had reported the following unsafe locking scenario:
CPU0 CPU1
---- ----
lock(s_active#228);
lock(&bdev->bd_mutex/1);
lock(s_active#228);
lock(&bdev->bd_mutex);
*** DEADLOCK ***
The deadlock may happen when one task (CPU1) is trying to delete a
partition in a block device and another task (CPU0) is accessing
tracing sysfs file (e.g. /sys/block/dm-1/trace/act_mask) in that
partition.
The s_active isn't an actual lock. It is a reference count (kn->count)
on the sysfs (kernfs) file. Removal of a sysfs file, however, require
a wait until all the references are gone. The reference count is
treated like a rwsem using lockdep instrumentation code.
The fact that a thread is in the sysfs callback method or in the
ioctl call means there is a reference to the opended sysfs or device
file. That should prevent the underlying block structure from being
removed.
Instead of using bd_mutex in the block_device structure, a new
blk_trace_mutex is now added to the request_queue structure to protect
access to the blk_trace structure.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fix typo in patch subject line, and prune a comment detailing how
the code used to work.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Josef Bacik [Sat, 6 May 2017 02:25:18 +0000 (22:25 -0400)]
nbd: ignore non-nbd ioctl's
In testing we noticed that nbd would spew if you ran a fio job against
the raw device itself. This is because fio calls a block device
specific ioctl, however the block layer will first pass this back to the
driver ioctl handler in case the driver wants to do something special.
Since the device was setup using netlink this caused us to spew every
time fio called this ioctl. Since we don't have special handling, just
error out for any non-nbd specific ioctl's that come in. This fixes the
spew.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Christoph Hellwig [Thu, 7 Sep 2017 11:54:35 +0000 (13:54 +0200)]
bsg-lib: don't free job in bsg_prepare_job
The job structure is allocated as part of the request, so we should not
free it in the error path of bsg_prepare_job.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mikulas Patocka [Wed, 13 Sep 2017 13:17:57 +0000 (09:17 -0400)]
brd: fix overflow in __brd_direct_access
The code in __brd_direct_access multiplies the pgoff variable by page size
and divides it by 512. It can cause overflow on 32-bit architectures. The
overflow happens if we create ramdisk larger than 4G and use it as a
sparse device.
This patch replaces multiplication and division with multiplication by the
number of sectors per page.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes:
1647b9b959c7 ("brd: add dax_operations support")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Babu Moger [Mon, 18 Sep 2017 16:53:29 +0000 (10:53 -0600)]
arch: change default endian for microblaze
Fix the default for microblaze. Michal Simek mentioned default for
microblaze should be CPU_LITTLE_ENDIAN.
Fixes : commit
206d3642d8ee ("arch/microblaze: add choice for endianness
and update Makefile")
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Thomas Meyer [Wed, 20 Sep 2017 22:29:36 +0000 (00:29 +0200)]
microblaze: Cocci spatch "vma_pages"
Use vma_pages function on vma object instead of explicit computation.
Found by coccinelle spatch "api/vma_pages.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 19 Sep 2017 14:40:21 +0000 (16:40 +0200)]
microblaze: Add missing kvm_para.h to Kbuild
Running make allmodconfig;make is throwing compilation error:
CC kernel/watchdog.o
In file included from ./include/linux/kvm_para.h:4:0,
from kernel/watchdog.c:29:
./include/uapi/linux/kvm_para.h:32:26: fatal error: asm/kvm_para.h: No
such file or directory
#include <asm/kvm_para.h>
^
compilation terminated.
make[1]: *** [kernel/watchdog.o] Error 1
make: *** [kernel/watchdog.o] Error 2
Reported-by: Michal Hocko <mhocko@kernel.org>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fixes:
83f0124ad81e87b ("microblaze: remove asm-generic wrapper headers")
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Michal Hocko <mhocko@suse.com>
Linus Torvalds [Sun, 24 Sep 2017 23:38:56 +0000 (16:38 -0700)]
Linux 4.14-rc2
Linus Torvalds [Sun, 24 Sep 2017 23:04:12 +0000 (16:04 -0700)]
Merge tag 'devicetree-fixes-for-4.14' of git://git./linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix build for !OF providing empty of_find_device_by_node
- fix Abracon vendor prefix
- sync dtx_diff include paths (again)
- a stm32h7 clock binding doc fix
* tag 'devicetree-fixes-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: clk: stm32h7: fix clock-cell size
scripts/dtc: dtx_diff - 2nd update of include dts paths to match build
dt-bindings: fix vendor prefix for Abracon
of: provide inline helper for of_find_device_by_node
Linus Torvalds [Sun, 24 Sep 2017 19:33:58 +0000 (12:33 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Another round of CR3/PCID related fixes (I think this addresses all
but one of the known problems with PCID support), an objtool fix plus
a Clang fix that (finally) solves all Clang quirks to build a bootable
x86 kernel as-is"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Fix inline asm call constraints for Clang
objtool: Handle another GCC stack pointer adjustment bug
x86/mm/32: Load a sane CR3 before cpu_init() on secondary CPUs
x86/mm/32: Move setup_clear_cpu_cap(X86_FEATURE_PCID) earlier
x86/mm/64: Stop using CR3.PCID == 0 in ASID-aware code
x86/mm: Factor out CR3-building code
Linus Torvalds [Sun, 24 Sep 2017 19:28:55 +0000 (12:28 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"A clocksource driver section mismatch fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/integrator: Fix section mismatch warning
Linus Torvalds [Sun, 24 Sep 2017 18:57:07 +0000 (11:57 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Three irqchip driver fixes, and an affinity mask helper function bug
fix affecting x86"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "genirq: Restrict effective affinity to interrupts actually using it"
irqchip.mips-gic: Fix shared interrupt mask writes
irqchip/gic-v4: Fix building with ancient gcc
irqchip/gic-v3: Iterate over possible CPUs by for_each_possible_cpu()
Linus Torvalds [Sun, 24 Sep 2017 18:53:13 +0000 (11:53 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull address-limit checking fixes from Ingo Molnar:
"This fixes a number of bugs in the address-limit (USER_DS) checks that
got introduced in the merge window, (mostly) affecting the ARM and
ARM64 platforms"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64/syscalls: Move address limit check in loop
arm/syscalls: Optimize address limit check
Revert "arm/syscalls: Check address limit on user-mode return"
syscalls: Use CHECK_DATA_CORRUPTION for addr_limit_user_check
Linus Torvalds [Sun, 24 Sep 2017 18:40:41 +0000 (11:40 -0700)]
Merge branch 'next-general' of git://git./linux/kernel/git/jmorris/linux-security
Pull misc security layer update from James Morris:
"This is the remaining 'general' change in the security tree for v4.14,
following the direct merging of SELinux (+ TOMOYO), AppArmor, and
seccomp.
That's everything now for the security tree except IMA, which will
follow shortly (I've been traveling for the past week with patchy
internet)"
* 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security: fix description of values returned by cap_inode_need_killpriv
Linus Torvalds [Sun, 24 Sep 2017 18:34:28 +0000 (11:34 -0700)]
Merge branch 'next-tpm' of git://git./linux/kernel/git/jmorris/linux-security
Pull TPM updates from James Morris:
"Here are the TPM updates from Jarkko for v4.14, which I've placed in
their own branch (next-tpm). I ended up cherry-picking them as other
changes had been made in Jarkko's branch after he sent me his original
pull request.
I plan on maintaining a separate branch for TPM (and other security
subsystems) from now on.
From Jarkko: 'Not much this time except a few fixes'"
* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: ibmvtpm: simplify crq initialization and document crq format
tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers
Documentation: tpm: add powered-while-suspended binding documentation
tpm: tpm_crb: constify acpi_device_id.
tpm: vtpm: constify vio_device_id
Michal Suchanek [Fri, 24 Feb 2017 19:35:16 +0000 (20:35 +0100)]
tpm: ibmvtpm: simplify crq initialization and document crq format
The crq is passed in registers and is the same on BE and LE hosts.
However, current implementation allocates a structure on-stack to
represent the crq, initializes the members swapping them to BE, and
loads the structure swapping it from BE. This is pointless and causes
GCC warnings about ununitialized members. Get rid of the structure and
the warnings.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Hamza Attak [Mon, 14 Aug 2017 18:09:16 +0000 (19:09 +0100)]
tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers
The patch simply replaces all msleep function calls with usleep_range calls
in the generic drivers.
Tested with an Infineon TPM 1.2, using the generic tpm-tis module, for a
thousand PCR extends, we see results going from 1m57s unpatched to 40s
with the new patch. We obtain similar results when using the original and
patched tpm_infineon driver, which is also part of the patch.
Similarly with a STM TPM 2.0, using the CRB driver, it takes about 20ms per
extend unpatched and around 7ms with the new patch.
Note that the PCR consistency is untouched with this patch, each TPM has
been tested with 10 million extends and the aggregated PCR value is
continuously verified to be correct.
As an extension of this work, this could potentially and easily be applied
to other vendor's drivers. Still, these changes are not included in the
proposed patch as they are untested.
Signed-off-by: Hamza Attak <hamza@hpe.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Enric Balletbo i Serra [Tue, 27 Jun 2017 10:27:23 +0000 (12:27 +0200)]
Documentation: tpm: add powered-while-suspended binding documentation
Add a new powered-while-suspended property to control the behavior of the
TPM suspend/resume.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Arvind Yadav [Thu, 6 Jul 2017 17:48:39 +0000 (23:18 +0530)]
tpm: tpm_crb: constify acpi_device_id.
acpi_device_id are not supposed to change at runtime. All functions
working with acpi_device_id provided by <acpi/acpi_bus.h> work with
const acpi_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
4198 608 0 4806 12c6 drivers/char/tpm/tpm_crb.o
File size After adding 'const':
text data bss dec hex filename
4262 520 0 4782 12ae drivers/char/tpm/tpm_crb.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Arvind Yadav [Thu, 17 Aug 2017 17:34:21 +0000 (23:04 +0530)]
tpm: vtpm: constify vio_device_id
vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with
const vio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Stefan Berger [Thu, 27 Jul 2017 02:27:05 +0000 (22:27 -0400)]
security: fix description of values returned by cap_inode_need_killpriv
cap_inode_need_killpriv returns 1 if security.capability exists and
has a value and inode_killpriv() is required, 0 otherwise. Fix the
description of the return value to reflect this.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Steven Rostedt (VMware) [Thu, 21 Sep 2017 17:00:21 +0000 (13:00 -0400)]
tracing: Remove RCU work arounds from stack tracer
Currently the stack tracer calls rcu_irq_enter() to make sure RCU
is watching when it records a stack trace. But if the stack tracer
is triggered while tracing inside of a rcu_irq_enter(), calling
rcu_irq_enter() unconditionally can be problematic.
The reason for having rcu_irq_enter() in the first place has been
fixed from within the saving of the stack trace code, and there's no
reason for doing it in the stack tracer itself. Just remove it.
Cc: stable@vger.kernel.org
Fixes:
0be964be0 ("module: Sanitize RCU usage and locking")
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Suggested-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Fri, 22 Sep 2017 21:36:32 +0000 (17:36 -0400)]
extable: Enable RCU if it is not watching in kernel_text_address()
If kernel_text_address() is called when RCU is not watching, it can cause an
RCU bug because is_module_text_address(), the is_kprobe_*insn_slot()
and is_bpf_text_address() functions require the use of RCU.
Only enable RCU if it is not currently watching before it calls
is_module_text_address(). The use of rcu_nmi_enter() is used to enable RCU
because kernel_text_address() can happen pretty much anywhere (like an NMI),
and even from within an NMI. It is called via save_stack_trace() that can be
called by any WARN() or tracing function, which can happen while RCU is not
watching (for example, going to or coming from idle, or during CPU take down
or bring up).
Cc: stable@vger.kernel.org
Fixes:
0be964be0 ("module: Sanitize RCU usage and locking")
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Fri, 22 Sep 2017 21:22:19 +0000 (17:22 -0400)]
extable: Consolidate *kernel_text_address() functions
The functionality between kernel_text_address() and _kernel_text_address()
is the same except that _kernel_text_address() does a little more (that
function needs a rename, but that can be done another time). Instead of
having duplicate code in both, simply have _kernel_text_address() calls
kernel_text_address() instead.
This is marked for stable because there's an RCU bug that can happen if
one of these functions gets called while RCU is not watching. That fix
depends on this fix to keep from having to write the fix twice.
Cc: stable@vger.kernel.org
Fixes:
0be964be0 ("module: Sanitize RCU usage and locking")
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Paul E. McKenney [Fri, 22 Sep 2017 21:10:22 +0000 (14:10 -0700)]
rcu: Allow for page faults in NMI handlers
A number of architecture invoke rcu_irq_enter() on exception entry in
order to allow RCU read-side critical sections in the exception handler
when the exception is from an idle or nohz_full CPU. This works, at
least unless the exception happens in an NMI handler. In that case,
rcu_nmi_enter() would already have exited the extended quiescent state,
which would mean that rcu_irq_enter() would (incorrectly) cause RCU
to think that it is again in an extended quiescent state. This will
in turn result in lockdep splats in response to later RCU read-side
critical sections.
This commit therefore causes rcu_irq_enter() and rcu_irq_exit() to
take no action if there is an rcu_nmi_enter() in effect, thus avoiding
the unscheduled return to RCU quiescent state. This in turn should
make the kernel safe for on-demand RCU voyeurism.
Link: http://lkml.kernel.org/r/20170922211022.GA18084@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes:
0be964be0 ("module: Sanitize RCU usage and locking")
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Linus Torvalds [Sat, 23 Sep 2017 16:14:06 +0000 (06:14 -1000)]
Merge branch 'parisc-4.14-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Unbreak parisc bootloader by avoiding a gcc-7 optimization to convert
multiple byte-accesses into one word-access.
- Add missing HWPOISON page fault handler code. I completely missed
that when I added HWPOISON support during this merge window and it
only showed up now with the madvise07 LTP test case.
- Fix backtrace unwinding to stop when stack start has been reached.
- Issue warning if initrd has been loaded into memory regions with
broken RAM modules.
- Fix HPMC handler (parisc hardware fault handler) to comply with
architecture specification.
- Avoid compiler warnings about too large frame sizes.
- Minor init-section fixes.
* 'parisc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Unbreak bootloader due to gcc-7 optimizations
parisc: Reintroduce option to gzip-compress the kernel
parisc: Add HWPOISON page fault handler code
parisc: Move init_per_cpu() into init section
parisc: Check if initrd was loaded into broken RAM
parisc: Add PDCE_CHECK instruction to HPMC handler
parisc: Add wrapper for pdc_instr() firmware function
parisc: Move start_parisc() into init section
parisc: Stop unwinding at start of stack
parisc: Fix too large frame size warnings
Linus Torvalds [Sat, 23 Sep 2017 15:47:04 +0000 (05:47 -1000)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
- Smattering of miscellanous fixes
- A five patch series for i40iw that had a patch (5/5) that was larger
than I would like, but I took it because it's needed for large scale
users
- An 8 patch series for bnxt_re that landed right as I was leaving on
PTO and so had to wait until now...they are all appropriate fixes for
-rc IMO
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (22 commits)
bnxt_re: Don't issue cmd to delete GID for QP1 GID entry before the QP is destroyed
bnxt_re: Fix memory leak in FRMR path
bnxt_re: Remove RTNL lock dependency in bnxt_re_query_port
bnxt_re: Fix race between the netdev register and unregister events
bnxt_re: Free up devices in module_exit path
bnxt_re: Fix compare and swap atomic operands
bnxt_re: Stop issuing further cmds to FW once a cmd times out
bnxt_re: Fix update of qplib_qp.mtu when modified
i40iw: Add support for port reuse on active side connections
i40iw: Add missing VLAN priority
i40iw: Call i40iw_cm_disconn on modify QP to disconnect
i40iw: Prevent multiple netdev event notifier registrations
i40iw: Fail open if there are no available MSI-X vectors
RDMA/vmw_pvrdma: Fix reporting correct opcodes for completion
IB/bnxt_re: Fix frame stack compilation warning
IB/mlx5: fix debugfs cleanup
IB/ocrdma: fix incorrect fall-through on switch statement
IB/ipoib: Suppress the retry related completion errors
iw_cxgb4: remove the stid on listen create failure
iw_cxgb4: drop listen destroy replies if no ep found
...
Linus Torvalds [Sat, 23 Sep 2017 15:41:27 +0000 (05:41 -1000)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix NAPI poll list corruption in enic driver, from Christian
Lamparter.
2) Fix route use after free, from Eric Dumazet.
3) Fix regression in reuseaddr handling, from Josef Bacik.
4) Assert the size of control messages in compat handling since we copy
it in from userspace twice. From Meng Xu.
5) SMC layer bug fixes (missing RCU locking, bad refcounting, etc.)
from Ursula Braun.
6) Fix races in AF_PACKET fanout handling, from Willem de Bruijn.
7) Don't use ARRAY_SIZE on spinlock array which might have zero
entries, from Geert Uytterhoeven.
8) Fix miscomputation of checksum in ipv6 udp code, from Subash Abhinov
Kasiviswanathan.
9) Push the ipv6 header properly in ipv6 GRE tunnel driver, from Xin
Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
inet: fix improper empty comparison
net: use inet6_rcv_saddr to compare sockets
net: set tb->fast_sk_family
net: orphan frags on stand-alone ptype in dev_queue_xmit_nit
MAINTAINERS: update git tree locations for ieee802154 subsystem
net: prevent dst uses after free
net: phy: Fix truncation of large IRQ numbers in phy_attached_print()
net/smc: no close wait in case of process shut down
net/smc: introduce a delay
net/smc: terminate link group if out-of-sync is received
net/smc: longer delay for client link group removal
net/smc: adapt send request completion notification
net/smc: adjust net_device refcount
net/smc: take RCU read lock for routing cache lookup
net/smc: add receive timeout check
net/smc: add missing dev_put
net: stmmac: Cocci spatch "of_table"
lan78xx: Use default values loaded from EEPROM/OTP after reset
lan78xx: Allow EEPROM write for less than MAX_EEPROM_SIZE
lan78xx: Fix for eeprom read/write when device auto suspend
...
Linus Torvalds [Sat, 23 Sep 2017 15:33:29 +0000 (05:33 -1000)]
Merge tag 'apparmor-pr-2017-09-22' of git://git./linux/kernel/git/jj/linux-apparmor
Pull apparmor updates from John Johansen:
"This is the apparmor pull request, similar to SELinux and seccomp.
It's the same series that I was sent to James' security tree + one
regression fix that was found after the series was sent to James and
would have been sent for v4.14-rc2.
Features:
- in preparation for secid mapping add support for absolute root view
based labels
- add base infastructure for socket mediation
- add mount mediation
- add signal mediation
minor cleanups and changes:
- be defensive, ensure unconfined profiles have dfas initialized
- add more debug asserts to apparmorfs
- enable policy unpacking to audit different reasons for failure
- cleanup conditional check for label in label_print
- Redundant condition: prev_ns. in [label.c:1498]
Bug Fixes:
- fix regression in apparmorfs DAC access permissions
- fix build failure on sparc caused by undeclared signals
- fix sparse report of incorrect type assignment when freeing label proxies
- fix race condition in null profile creation
- Fix an error code in aafs_create()
- Fix logical error in verify_header()
- Fix shadowed local variable in unpack_trans_table()"
* tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: fix apparmorfs DAC access permissions
apparmor: fix build failure on sparc caused by undeclared signals
apparmor: fix incorrect type assignment when freeing proxies
apparmor: ensure unconfined profiles have dfas initialized
apparmor: fix race condition in null profile creation
apparmor: move new_null_profile to after profile lookup fns()
apparmor: add base infastructure for socket mediation
apparmor: add more debug asserts to apparmorfs
apparmor: make policy_unpack able to audit different info messages
apparmor: add support for absolute root view based labels
apparmor: cleanup conditional check for label in label_print
apparmor: add mount mediation
apparmor: add the ability to mediate signals
apparmor: Redundant condition: prev_ns. in [label.c:1498]
apparmor: Fix an error code in aafs_create()
apparmor: Fix logical error in verify_header()
apparmor: Fix shadowed local variable in unpack_trans_table()
Josh Poimboeuf [Wed, 20 Sep 2017 21:24:33 +0000 (16:24 -0500)]
x86/asm: Fix inline asm call constraints for Clang
For inline asm statements which have a CALL instruction, we list the
stack pointer as a constraint to convince GCC to ensure the frame
pointer is set up first:
static inline void foo()
{
register void *__sp asm(_ASM_SP);
asm("call bar" : "+r" (__sp))
}
Unfortunately, that pattern causes Clang to corrupt the stack pointer.
The fix is easy: convert the stack pointer register variable to a global
variable.
It should be noted that the end result is different based on the GCC
version. With GCC 6.4, this patch has exactly the same result as
before:
defconfig defconfig-nofp distro distro-nofp
before
9820389 9491555 8816046 8516940
after
9820389 9491555 8816046 8516940
With GCC 7.2, however, GCC's behavior has changed. It now changes its
behavior based on the conversion of the register variable to a global.
That somehow convinces it to *always* set up the frame pointer before
inserting *any* inline asm. (Therefore, listing the variable as an
output constraint is a no-op and is no longer necessary.) It's a bit
overkill, but the performance impact should be negligible. And in fact,
there's a nice improvement with frame pointers disabled:
defconfig defconfig-nofp distro distro-nofp
before
9796316 9468236 9076191 8790305
after
9796957 9464267 9076381 8785949
So in summary, while listing the stack pointer as an output constraint
is no longer necessary for newer versions of GCC, it's still needed for
older versions.
Suggested-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/3db862e970c432ae823cf515c52b54fec8270e0e.1505942196.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Josh Poimboeuf [Wed, 20 Sep 2017 21:24:32 +0000 (16:24 -0500)]
objtool: Handle another GCC stack pointer adjustment bug
The kbuild bot reported the following warning with GCC 4.4 and a
randconfig:
net/socket.o: warning: objtool: compat_sock_ioctl()+0x1083: stack state mismatch: cfa1=7+160 cfa2=-1+0
This is caused by another GCC non-optimization, where it backs up and
restores the stack pointer for no apparent reason:
2f91: 48 89 e0 mov %rsp,%rax
2f94: 4c 89 e7 mov %r12,%rdi
2f97: 4c 89 f6 mov %r14,%rsi
2f9a: ba 20 00 00 00 mov $0x20,%edx
2f9f: 48 89 c4 mov %rax,%rsp
This issue would have been happily ignored before the following commit:
dd88a0a0c861 ("objtool: Handle GCC stack pointer adjustment bug")
But now that objtool is paying attention to such stack pointer writes
to/from a register, it needs to understand them properly. In this case
that means recognizing that the "mov %rsp, %rax" instruction is
potentially a backup of the stack pointer.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes:
dd88a0a0c861 ("objtool: Handle GCC stack pointer adjustment bug")
Link: http://lkml.kernel.org/r/8c7aa8e9a36fbbb6655d9d8e7cea58958c912da8.1505942196.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Sat, 23 Sep 2017 03:40:11 +0000 (17:40 -1000)]
Merge tag 'acpi-4.14-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix the initialization of resources in the ACPI WDAT watchdog
driver, a recent regression in the ACPI device properties handling, a
recent change in behavior causing the ACPI_HANDLE() macro to only work
for GPL code and create a MAINTAINERS entry for ACPI PMIC drivers in
order to specify the official reviewers for that code.
Specifics:
- Fix the initialization of resources in the ACPI WDAT watchdog
driver that uses unititialized memory which causes compiler
warnings to be triggered (Arnd Bergmann).
- Fix a recent regression in the ACPI device properties handling that
causes some device properties data to be skipped during enumeration
(Sakari Ailus).
- Fix a recent change in behavior that caused the ACPI_HANDLE() macro
to stop working for non-GPL code which is a problem for the NVidia
binary graphics driver, for example (John Hubbard).
- Add a MAINTAINERS entry for the ACPI PMIC drivers to specify the
official reviewers for that code (Rafael Wysocki)"
* tag 'acpi-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: properties: Return _DSD hierarchical extension (data) sub-nodes correctly
ACPI / bus: Make ACPI_HANDLE() work for non-GPL code again
ACPI / watchdog: properly initialize resources
ACPI / PMIC: Add code reviewers to MAINTAINERS
David S. Miller [Sat, 23 Sep 2017 03:33:18 +0000 (20:33 -0700)]
Merge branch 'net-fix-reuseaddr-regression'
Josef Bacik says:
====================
net: fix reuseaddr regression
I introduced a regression when reworking the fastreuse port stuff that allows
bind conflicts to occur once a reuseaddr successfully opens on an existing tb.
The root cause is I reversed an if statement which caused us to set the tb as if
there were no owners on the socket if there were, which obviously is not
correct.
Dave could you please queue these changes up for -stable, I've run them through
the net tests and added another test to check for this problem specifically.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Sat, 23 Sep 2017 00:20:08 +0000 (20:20 -0400)]
inet: fix improper empty comparison
When doing my reuseport rework I screwed up and changed a
if (hlist_empty(&tb->owners))
to
if (!hlist_empty(&tb->owners))
This is obviously bad as all of the reuseport/reuse logic was reversed,
which caused weird problems like allowing an ipv4 bind conflict if we
opened an ipv4 only socket on a port followed by an ipv6 only socket on
the same port.
Fixes:
b9470c27607b ("inet: kill smallest_size and smallest_port")
Reported-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Sat, 23 Sep 2017 00:20:07 +0000 (20:20 -0400)]
net: use inet6_rcv_saddr to compare sockets
In ipv6_rcv_saddr_equal() we need to use inet6_rcv_saddr(sk) for the
ipv6 compare with the fast socket information to make sure we're doing
the proper comparisons.
Fixes:
637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk")
Reported-and-tested-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Sat, 23 Sep 2017 00:20:06 +0000 (20:20 -0400)]
net: set tb->fast_sk_family
We need to set the tb->fast_sk_family properly so we can use the proper
comparison function for all subsequent reuseport bind requests.
Fixes:
637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk")
Reported-and-tested-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 22 Sep 2017 23:42:37 +0000 (19:42 -0400)]
net: orphan frags on stand-alone ptype in dev_queue_xmit_nit
Zerocopy skbs frags are copied when the skb is looped to a local sock.
Commit
1080e512d44d ("net: orphan frags on receive") introduced calls
to skb_orphan_frags to deliver_skb and __netif_receive_skb for this.
With msg_zerocopy, these skbs can also exist in the tx path and thus
loop from dev_queue_xmit_nit. This already calls deliver_skb in its
loop. But it does not orphan before a separate pt_prev->func().
Add the missing skb_orphan_frags_rx.
Changes
v1->v2: handle skb_orphan_frags_rx failure
Fixes:
1f8b977ab32d ("sock: enable MSG_ZEROCOPY")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Sep 2017 03:28:59 +0000 (17:28 -1000)]
Merge tag 'pm-4.14-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a cpufreq regression introduced by recent changes related to
the generic DT driver, an initialization time memory leak in cpuidle
on ARM, a PM core bug that may cause system suspend/resume to fail on
some systems, a request type validation issue in the PM QoS framework
and two documentation-related issues.
Specifics:
- Fix a regression in cpufreq on systems using DT as the source of
CPU configuration information where two different code paths
attempt to create the cpufreq-dt device object (there can be only
one) and fix up the "compatible" matching for some TI platforms on
top of that (Viresh Kumar, Dave Gerlach).
- Fix an initialization time memory leak in cpuidle on ARM which
occurs if the cpuidle driver initialization fails (Stefan Wahren).
- Fix a PM core function that checks whether or not there are any
system suspend/resume callbacks for a device, but forgets to check
legacy callbacks which then may be skipped incorrectly and the
system may crash and/or the device may become unusable after a
suspend-resume cycle (Rafael Wysocki).
- Fix request type validation for latency tolerance PM QoS requests
which may lead to unexpected behavior (Jan Schönherr).
- Fix a broken link to PM documentation from a header file and a typo
in a PM document (Geert Uytterhoeven, Rafael Wysocki)"
* tag 'pm-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: ti-cpufreq: Support additional am43xx platforms
ARM: cpuidle: Avoid memleak if init fail
cpufreq: dt-platdev: Add some missing platforms to the blacklist
PM: core: Fix device_pm_check_callbacks()
PM: docs: Drop an excess character from devices.rst
PM / QoS: Use the correct variable to check the QoS request type
driver core: Fix link to device power management documentation
Linus Torvalds [Sat, 23 Sep 2017 03:23:41 +0000 (17:23 -1000)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- fixes for two long standing issues (lock up and a crash) in force
feedback handling in uinput driver
- tweak to firmware update timing in Elan I2C touchpad driver.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - extend Flash-Write delay
Input: uinput - avoid crash when sending FF request to device going away
Input: uinput - avoid FF flush when destroying device
Linus Torvalds [Sat, 23 Sep 2017 02:16:41 +0000 (16:16 -1000)]
Merge tag 'seccomp-v4.14-rc2' of git://git./linux/kernel/git/kees/linux
Pull seccomp updates from Kees Cook:
"Major additions:
- sysctl and seccomp operation to discover available actions
(tyhicks)
- new per-filter configurable logging infrastructure and sysctl
(tyhicks)
- SECCOMP_RET_LOG to log allowed syscalls (tyhicks)
- SECCOMP_RET_KILL_PROCESS as the new strictest possible action
- self-tests for new behaviors"
[ This is the seccomp part of the security pull request during the merge
window that was nixed due to unrelated problems - Linus ]
* tag 'seccomp-v4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
samples: Unrename SECCOMP_RET_KILL
selftests/seccomp: Test thread vs process killing
seccomp: Implement SECCOMP_RET_KILL_PROCESS action
seccomp: Introduce SECCOMP_RET_KILL_PROCESS
seccomp: Rename SECCOMP_RET_KILL to SECCOMP_RET_KILL_THREAD
seccomp: Action to log before allowing
seccomp: Filter flag to log all actions except SECCOMP_RET_ALLOW
seccomp: Selftest for detection of filter flag support
seccomp: Sysctl to configure actions that are allowed to be logged
seccomp: Operation for checking if an action is available
seccomp: Sysctl to display available actions
seccomp: Provide matching filter for introspection
selftests/seccomp: Refactor RET_ERRNO tests
selftests/seccomp: Add simple seccomp overhead benchmark
selftests/seccomp: Add tests for basic ptrace actions
Linus Torvalds [Sat, 23 Sep 2017 02:11:48 +0000 (16:11 -1000)]
Merge tag '4.14-smb3-fixes-from-recent-test-events-for-stable' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Various SMB3 fixes for stable and security improvements from the
recently completed SMB3/Samba test events
* tag '4.14-smb3-fixes-from-recent-test-events-for-stable' of git://git.samba.org/sfrench/cifs-2.6:
SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags
SMB3: handle new statx fields
SMB: Validate negotiate (to protect against downgrade) even if signing off
cifs: release auth_key.response for reconnect.
cifs: release cifs root_cred after exit_cifs
CIFS: make arrays static const, reduces object code size
[SMB3] Update session and share information displayed for debugging SMB2/SMB3
cifs: show 'soft' in the mount options for hard mounts
SMB3: Warn user if trying to sign connection that authenticated as guest
SMB3: Fix endian warning
Fix SMB3.1.1 guest authentication to Samba