OSDN Git Service
Jim Lin [Thu, 15 May 2014 00:32:58 +0000 (17:32 -0700)]
clk: tegra: Fix xusb_fs_src mux
The parent-to-index mapping for xusb_fs_src is incorrect.
Fix it by adding a mux table.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Jim Lin [Thu, 15 May 2014 00:32:57 +0000 (17:32 -0700)]
clk: tegra: Enable hardware control of PLLE
Enable hardware control of PLLE spread-spectrum, IDDQ, and enable
controls when enabling PLLE. The hardware (e.g. XUSB) using PLLE
will use these controls for power-saving optimizations.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Anders Berg [Thu, 15 May 2014 13:42:25 +0000 (15:42 +0200)]
clk: Add clock driver for AXM55xx SoC
Add clk driver to support clock blocks found on the AXM55xx devices. The driver
provides clock implementations for three different types of clock devices on
the AXM55xx device: PLL clock, a clock divider and a clock mux.
Signed-off-by: Anders Berg <anders.berg@lsi.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Laurent Pinchart [Thu, 22 May 2014 18:02:14 +0000 (20:02 +0200)]
clk: shmobile: mstp: Fix the is_enabled() operation
The MSTP[SC]R registers have clock stop bits, not clock enable bits. The
bit value should thus be inverted in the is_enabled() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Sylwester Nawrocki [Mon, 19 May 2014 17:22:50 +0000 (19:22 +0200)]
clk: Add of_clk_get_by_clkspec() helper
This patch adds of_clk_get_by_clkspec() helper function, which does only
a struct clk lookup from the clock providers. It is used in the subsequent
patch where parsing of a clock from device tree and the lookup from
providers needed to be split.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Linus Walleij [Tue, 15 Apr 2014 08:29:45 +0000 (10:29 +0200)]
clk: impd1: add pclk clocks
The IM-PD1 PrimeCells all have pclk assignments though this clock
cannot be controlled, and we need to provide this as a dummy
clock for the PL061 GPIO driver to probe, so let's assign it to
all the cells on the board.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Mike Turquette [Wed, 21 May 2014 04:48:38 +0000 (21:48 -0700)]
Merge tag 'zynq-clk-for-3.16' of git://git.xilinx.com/linux-xlnx into clk-next-zynq
arm: Xilinx Zynq clk patches for v3.16
- Keep debug clocks in bootup state
- Fix email address in si570
Michal Simek [Thu, 3 Apr 2014 15:05:02 +0000 (17:05 +0200)]
clk: si570: Fix email address specifiction
Just fix missing ">" in the email.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stephen Boyd [Fri, 16 May 2014 17:05:14 +0000 (10:05 -0700)]
clk: qcom: Fix msm8660 GCC probe
When consolidating the msm8660 GCC probe code I forgot to keep
around these temporary clock registrations. Put them back so the
clock tree is not entirely orphaned.
Fixes:
49fc825f0cc2 (clk: qcom: Consolidate common probe code)
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Mike Turquette [Fri, 16 May 2014 23:09:46 +0000 (16:09 -0700)]
Merge branch 'clk-fixes' into clk-next
Tuomas Tynkkynen [Fri, 16 May 2014 13:50:20 +0000 (16:50 +0300)]
clk: tegra: Fix wrong value written to PLLE_AUX
The value written to PLLE_AUX was incorrect due to a wrong variable
being used. Without this fix SATA does not work.
Cc: stable@vger.kernel.org
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: improved changelog]
Fabio Estevam [Fri, 9 May 2014 03:01:50 +0000 (00:01 -0300)]
Documentation: clock: fixed-clock: Remove unsupported 'gpios' property
Remove the 'gpios' property from the documentation as this is something that the
current fixed clock driver does not handle.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Arnd Bergmann [Thu, 8 May 2014 14:56:16 +0000 (16:56 +0200)]
clk/versatile: export symbols for impd1
The impd1 code on mach-integrator can be a loadable module,
so we have to export icst_clk_register, integrator_impd1_clk_init
and integrator_impd1_clk_exit.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Mike Turquette [Thu, 15 May 2014 06:16:32 +0000 (23:16 -0700)]
Merge tag 'clk-hisi-for-v3.16' of https://git./linux/kernel/git/hzhuang1/linux into clk-next-hisilicon
enable hix5hd2 clock
Hans de Goede [Mon, 12 May 2014 12:04:47 +0000 (14:04 +0200)]
clk: sunxi: Fixup clk_sunxi_mmc_phase_control to take a clk rather then a hw_clk
__clk_get_hw is supposed to be used by clk providers, not clk consumers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Mike Turquette [Tue, 13 May 2014 23:04:19 +0000 (16:04 -0700)]
Merge tag 'clk-mvebu-3.16' of git://git.infradead.org/linux-mvebu into clk-next-mvebu
clk mvebu changes for v3.16
- orion5x: brand new driver
Simon Horman [Thu, 17 Apr 2014 23:05:51 +0000 (08:05 +0900)]
clk: shmobile: r8a7779: Add MSTP clock support
Add MSTP clock support for the r8a7779 SoC
The only change required appears to be to note a new
compatibility string in the bindings.
Cc: devicetree@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Simon Horman [Thu, 17 Apr 2014 23:05:50 +0000 (08:05 +0900)]
clk: shmobile: r8a7779: Add clocks support
The R8A7779 SoC has several clocks that are too custom to be supported in a
generic driver. Those clocks are all fixed rate clocks with multiplier and
divisor set according to boot mode configuration.
Based on work for R-Car Gen2 SoCs by Laurent Pinchart.
Cc: devicetree@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Mike Turquette [Tue, 13 May 2014 02:11:13 +0000 (19:11 -0700)]
Merge tag 'socfpga-clk-update-for-v3.16' of git://git.rocketboards.org/linux-socfpga-next into clk-next-socfpga
Adds support getting the divider registers for the MAIN PLL that was once
thought to be hidden.
Geert Uytterhoeven [Mon, 14 Apr 2014 17:00:40 +0000 (19:00 +0200)]
clk: Improve clock-indices binding documentation
Improve the wording for the clock-indices binding documentation.
Also replace "empty nodes" by "empty strings", as reported before by Sergei
Shtylyov.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Geert Uytterhoeven [Tue, 22 Apr 2014 13:11:42 +0000 (15:11 +0200)]
clk: Improve clk_ops documentation
General:
- Add parameter names to .round_rate() and .set_rate().
Documentation/clk.txt:
- Add missing parameter for .set_rate(),
- Add missing .debug_init().
include/linux/clk-provider.h:
- Add parent rate documentation for .round_rate(),
- Reorder documentation to match implementation order,
- Add missing documentation for .init().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Geert Uytterhoeven [Tue, 22 Apr 2014 13:11:41 +0000 (15:11 +0200)]
clk: Fixup spacing in comments
- Remove spaces in front of TABs,
- Correct indentation for some CLK_* flag descriptions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Mike Turquette [Mon, 12 May 2014 23:55:33 +0000 (16:55 -0700)]
Merge branch 'clk-fixes' into clk-next
Ben Dooks [Tue, 15 Apr 2014 16:06:34 +0000 (17:06 +0100)]
clk: shmobile: clk-mstp: change to using clock-indices
With the addition of clock-indices, we need to change the renesas
clock implementation to use these instead of the local definition
of "renesas,clock-indices".
Since this will break booting with older device trees, we add a
simple auto-detection of which properties are present.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Dinh Nguyen [Mon, 12 May 2014 17:27:22 +0000 (12:27 -0500)]
clk: socfpga: add divider registers to the main pll outputs
The C0(mpu_clk), C1(main_clk), and C2(dbg_base_clk) outputs from the main
PLL go through a pre-divider before coming into the system. These registers
were hidden for the CycloneV platform, but are now used for the ArriaV
platform.
This patch updates the clock driver to read the div-reg property for the
socfpga-periph-clk clocks. Also moves the div_mask define to clk.h for re-use.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Zhangfei Gao [Mon, 21 Apr 2014 04:07:27 +0000 (12:07 +0800)]
clk: hisi: add clk-hix5hd2.c
Signed-off-by: Haifeng Yan <haifeng.yan@linaro.org>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Zhangfei Gao [Tue, 22 Apr 2014 07:42:47 +0000 (15:42 +0800)]
clk: hisi: add hisi_clk_register_gate
Add hisi_clk_register_gate register clk gate table
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Zhangfei Gao [Mon, 21 Apr 2014 03:35:21 +0000 (11:35 +0800)]
clk: hisi: use clk_register_mux_table in hisi_clk_register_mux
Platform hix5hd2 use mux table, so use clk_register_mux_table instead
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Emilio López [Fri, 2 May 2014 15:57:16 +0000 (17:57 +0200)]
clk: sunxi: Implement MMC phase control
HdG: add header exporting clk_sunxi_mmc_phase_control
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Emilio López [Fri, 2 May 2014 15:57:15 +0000 (17:57 +0200)]
clk: sunxi: factors: automatic reparenting support
This commit implements .determine_rate, so that our factor clocks can be
reparented when needed.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Kumar Gala [Fri, 4 Apr 2014 16:32:56 +0000 (11:32 -0500)]
clk: qcom: Various fixes for MSM8960's global clock controller
* Remove CE2_SLEEP_CLK, doesn't exist on 8960 family SoCs
* Fix incorrect offset for PMIC_SSBI2_RESET
* Fix typo:
SIC_TIC -> SPS_TIC_H
SFAB_ADM0_M2_A_CLK -> SFAB_ADM0_M2_H_CLK
* Fix naming convention:
SFAB_CFPB_S_HCLK -> SFAB_CFPB_S_H_CLK
SATA_SRC_CLK -> SATA_CLK_SRC
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Kumar Gala [Fri, 4 Apr 2014 16:31:29 +0000 (11:31 -0500)]
clk: qcom: Add basic support for APQ8064 global clock controller clocks
The APQ8064 and MSM8960 share a significant amount of clock data and
code between the two SoCs. Rather than duplicating the data we just add
support for a unqiue APQ8064 clock table into the MSM8960 code.
For now add just enough clocks to get a basic serial port going on an
APQ8064 device.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: trivial conflict due to missing ipq8064 support]
Stephen Boyd [Sat, 22 Mar 2014 00:59:37 +0000 (17:59 -0700)]
clk: qcom: Consolidate common probe code
Most of the probe code is the same between all the different
clock controllers. Consolidate the code into a common.c file.
This makes changes to the common probe parts easier and reduces
chances for bugs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Stephen Boyd [Wed, 26 Mar 2014 23:06:37 +0000 (16:06 -0700)]
clk: Ignore error and NULL pointers passed to clk_{unprepare, disable}()
This simplifies error paths in drivers that use optional clocks
by allowing the NULL or error pointer to be passed
unconditionally.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Stephen Boyd [Wed, 26 Mar 2014 23:06:36 +0000 (16:06 -0700)]
clk: Consolidate recalc rate logic
The same if-else statement exists four times to recalculate the
rate of a clock. Consolidate this logic into a single function to
save some lines.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Stephen Boyd [Wed, 26 Mar 2014 23:06:35 +0000 (16:06 -0700)]
clk: Don't check for missing ops in clk_set_parent()
We dereference clk->ops during clock registration so this check
for NULL ops can't possibly ever be true.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:26:27 +0000 (16:26 -0500)]
ARM: dts: use real clocks for bcm21664
Replace the "fake" fixed-rate clocks used previously for the
bcm21664 family with "real" ones.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:26:26 +0000 (16:26 -0500)]
clk: bcm21664: use common clock framework
Define the set of CCUs and provided clocks sufficient to satisfy the
needs of all the existing clock references for BCM21664. Replace
the "fake" fixed-rate clocks used previously with "real" ones.
Note that only the minimal set of these clocks and CCUs is defined
here. More clock definitions will need to be added as required by
the addition of additional drivers.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:26:25 +0000 (16:26 -0500)]
ARM: dts: define clock binding for bcm21664
Document the device tree binding for Broadcom BCM28164 clock control
units and clocks. This SoC uses Kona CCUs, similar to the BCM281XX
SoC family.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:26:24 +0000 (16:26 -0500)]
ARM: dts: revise kona clock binding document
The next patch defines a binding for a new Broadcom SoC that uses
Kona style CCUs for its clocks. Update the generic Kona clock
binding document so it's more natural to accomodate the definitions
of additional SoC families.
Specifically:
- Define the compatible string values generically, referring
to specific per-model values later in the document.
- Put the device tree example immediately after the required
properties listing, before the tables of SoC-specific values.
- Clearly identify the start of the section defining specific
values related to the BCM281XX family
- Add a list of the specific BCM281XX family compatible strings.
- Reword the description of the table slightly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:26:23 +0000 (16:26 -0500)]
clk: bcm281xx: move compatible string definitions
The Broadcom 281xx clock code uses a #define for the compatible
string for it's clock control units (CCUs). Rather than defining
those in the C source file, define them in the header file that's
shared by both the code and the device tree source file (along with
all the clock ids).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:11:43 +0000 (16:11 -0500)]
clk: bcm281xx: add clock hysteresis support
Add support for clock gate hysteresis control. For now, if it's
defined for a clock, it's enabled.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:11:42 +0000 (16:11 -0500)]
clk: bcm281xx: add clock policy support
Add support for CCU policy engine control, and also for setting the
mask bits for bus clocks that require a policy change to get
activated. This includes adding validity checking framework for
CCUs, to validate the policy fields if defined.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:11:41 +0000 (16:11 -0500)]
clk: bcm281xx: define CCU clock data statically
Rather than "manually" setting up each CCU's clock entries at run
time, define a flexible array of generic Kona clock structures
within the CCU structure itself. Each of these entries contains
generic kona clock information (like its CCU pointer and clock
framework initialization data). Each also has a pointer to a
structure contianing clock type-dependent initialization data
(like register definitions).
Since we'll iterate over these arrays we need to be sure they have
slots for all potential clock index values. (E.g. for the root CCU
we must have at least BCM281XX_ROOT_CCU_CLOCK_COUNT slots.) To
ensure this we always define an extra entry and fill it using the
special initializer LAST_KONA_CLK.
Just about everything we need to know about a clock can be defined
statically. As a result, kona_clk_setup() can be changed to take
just a kona_clk structure as its argument, and peri_clk_setup() can
be simplified. With the information pre-defined we are also able
to handle most clock setup genericially. We can do away with the
CCU-specific callback functions that previously were needed to set
up the entries in CCU's clock array.
Move the definition of the ccu_data structure down in "clk-kona.h"
to avoid a forward dependency.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:11:40 +0000 (16:11 -0500)]
clk: bcm281xx: initialize CCU structures statically
We know up front how many CCU's we'll support, so there's no need to
allocate their data structures dynamically. Define a macro
KONA_CCU_COMMON() to simplify the initialization of many of the
fields in a ccu_data structure. Pass the address of a statically
defined CCU structure to kona_dt_ccu_setup() rather than having that
function allocate one.
We also know at build time how many clocks a given CCU will provide,
though the number of of them for each CCU is different. Record the
number of clocks we need in the CCU's clk_onecell_data struct
(which is used when we register the CCU with the common clock code
as a clock provider). Rename that struct field "clk_data" (because
"data" alone gets a little confusing).
Use the known clock count to move the allocation of each CCU's
clocks array into ccu_clks_setup() rather than having each CCU's
setup callback function do it.
(The real motivation behind all of this is that we'll be doing some
static initialization of some additional CCU-specific data soon.)
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:11:39 +0000 (16:11 -0500)]
clk: bcm281xx: change some symbol names
As I developed the bcm281xx clock code I understood there were
restrictions on device tree "compatible" strings names, and as a
result "bcm11351" was used in places despite the part family being
more properly called "bcm281xx". This can be a little confusing.
In some cases I went to far and things using "bcm11351" when that
was not necessary.
This patch remedies this. It renames the symbol used to define the
"compatible" string (but not its value) so it uses "BCM281XX".
Similarly, the name names provided to the CLK_OF_DECLARE() macro
are changed, hoping to minimize the number of places that the
confusing "11351" string is used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:11:38 +0000 (16:11 -0500)]
clk: bcm281xx: use init_data.name for clock name
Use the init_data.name field to hold the name of a Kona clock rather
than duplicating it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Alex Elder [Mon, 21 Apr 2014 21:11:37 +0000 (16:11 -0500)]
clk: bcm281xx: warn if ccu_wait_bit() fails
Don't let a failure of ccu_wait_bit() go unnoticed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Maxime COQUELIN [Wed, 29 Jan 2014 16:24:08 +0000 (17:24 +0100)]
clk: divider: Optimize clk_divider_bestdiv loop
Currently, the for-loop used to try all the different dividers to find the
one that best fit tries all the values from 1 to max_div, incrementing by one.
In case of power-of-two, or table based divider, the loop isn't optimal.
Instead of incrementing by one, this patch provides directly the next divider.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Maxime COQUELIN [Wed, 29 Jan 2014 16:24:07 +0000 (17:24 +0100)]
clk: divider: Add round to closest divider
In some cases, we want to be able to round the divider to the closest one,
instead than rounding up.
This patch adds a new CLK_DIVIDER_ROUND_CLOSEST flag to specify the divider
has to round to closest div, keeping rounding up as de default behaviour.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Stephen Boyd [Fri, 18 Apr 2014 23:29:43 +0000 (16:29 -0700)]
clk: Fix slab corruption in clk_unregister()
When a clock is unregsitered, we iterate over the list of
children and reparent them to NULL (i.e. orphan list). While
iterating the list, we should use the safe iterators because the
children list for this clock is changing when we reparent the
children to NULL. Failure to iterate safely can lead to slab
corruption like this:
=============================================================================
BUG kmalloc-128 (Not tainted): Poison overwritten
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: 0xed0c4900-0xed0c4903. First byte 0x0 instead of 0x6b
INFO: Allocated in clk_register+0x20/0x1bc age=297 cpu=2 pid=70
__slab_alloc.isra.39.constprop.42+0x410/0x454
kmem_cache_alloc_trace+0x200/0x24c
clk_register+0x20/0x1bc
devm_clk_register+0x34/0x68
0xbf0000f0
platform_drv_probe+0x18/0x48
driver_probe_device+0x94/0x360
__driver_attach+0x94/0x98
bus_for_each_dev+0x54/0x88
bus_add_driver+0xe8/0x204
driver_register+0x78/0xf4
do_one_initcall+0xc4/0x17c
load_module+0x19ac/0x2294
SyS_init_module+0xa4/0x110
ret_fast_syscall+0x0/0x48
INFO: Freed in clk_unregister+0xd4/0x140 age=23 cpu=2 pid=73
__slab_free+0x38/0x41c
clk_unregister+0xd4/0x140
release_nodes+0x164/0x1d8
__device_release_driver+0x60/0xb0
driver_detach+0xb4/0xb8
bus_remove_driver+0x5c/0xc4
SyS_delete_module+0x148/0x1d8
ret_fast_syscall+0x0/0x48
INFO: Slab 0xeec50b90 objects=25 used=0 fp=0xed0c5400 flags=0x4080
INFO: Object 0xed0c48c0 @offset=2240 fp=0xed0c4a00
Bytes b4
ed0c48b0: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Object
ed0c48c0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object
ed0c48d0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object
ed0c48e0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object
ed0c48f0: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object
ed0c4900: 00 00 00 00 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b ....kkkkkkkkkkkk
Object
ed0c4910: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object
ed0c4920: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object
ed0c4930: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkkkkkkkkkk.
Redzone
ed0c4940: bb bb bb bb ....
Padding
ed0c49e8: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZZZZZZZZZ
Padding
ed0c49f8: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
CPU: 3 PID: 75 Comm: mdev Tainted: G B
3.14.0-11033-g2054ba5ca781 #35
[<
c0014be0>] (unwind_backtrace) from [<
c0012240>] (show_stack+0x10/0x14)
[<
c0012240>] (show_stack) from [<
c04b74a0>] (dump_stack+0x70/0xbc)
[<
c04b74a0>] (dump_stack) from [<
c00f7a78>] (check_bytes_and_report+0xbc/0x100)
[<
c00f7a78>] (check_bytes_and_report) from [<
c00f7c48>] (check_object+0x18c/0x218)
[<
c00f7c48>] (check_object) from [<
c00f7efc>] (__free_slab+0x104/0x144)
[<
c00f7efc>] (__free_slab) from [<
c04b6668>] (__slab_free+0x3dc/0x41c)
[<
c04b6668>] (__slab_free) from [<
c014c008>] (load_elf_binary+0x88/0x12b4)
[<
c014c008>] (load_elf_binary) from [<
c0105a44>] (search_binary_handler+0x78/0x18c)
[<
c0105a44>] (search_binary_handler) from [<
c0106fc0>] (do_execve+0x490/0x5dc)
[<
c0106fc0>] (do_execve) from [<
c0036b8c>] (____call_usermodehelper+0x134/0x168)
[<
c0036b8c>] (____call_usermodehelper) from [<
c000f048>] (ret_from_fork+0x14/0x2c)
FIX kmalloc-128: Restoring 0xed0c4900-0xed0c4903=0x6b
Fixes:
fcb0ee6a3d33 (clk: Implement clk_unregister)
Cc: Jiada Wang <jiada_wang@mentor.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@vger.kernel.org
Stephen Boyd [Fri, 18 Apr 2014 23:29:42 +0000 (16:29 -0700)]
clk: Fix double free due to devm_clk_register()
Now that clk_unregister() frees the struct clk we're
unregistering we'll free memory twice: first we'll call kfree()
in __clk_release() with an address kmalloc doesn't know about and
second we'll call kfree() in the devres layer. Remove the
allocation of struct clk in devm_clk_register() and let
clk_release() handle it. This fixes slab errors like:
=============================================================================
BUG kmalloc-128 (Not tainted): Invalid object pointer 0xed08e8d0
-----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Slab 0xeec503f8 objects=25 used=15 fp=0xed08ea00 flags=0x4081
CPU: 2 PID: 73 Comm: rmmod Tainted: G B
3.14.0-11032-g526e9c764381 #34
[<
c0014be0>] (unwind_backtrace) from [<
c0012240>] (show_stack+0x10/0x14)
[<
c0012240>] (show_stack) from [<
c04b74dc>] (dump_stack+0x70/0xbc)
[<
c04b74dc>] (dump_stack) from [<
c00f6778>] (slab_err+0x74/0x84)
[<
c00f6778>] (slab_err) from [<
c04b6278>] (free_debug_processing+0x2cc/0x31c)
[<
c04b6278>] (free_debug_processing) from [<
c04b6300>] (__slab_free+0x38/0x41c)
[<
c04b6300>] (__slab_free) from [<
c03931bc>] (clk_unregister+0xd4/0x140)
[<
c03931bc>] (clk_unregister) from [<
c02fb774>] (release_nodes+0x164/0x1d8)
[<
c02fb774>] (release_nodes) from [<
c02f8698>] (__device_release_driver+0x60/0xb0)
[<
c02f8698>] (__device_release_driver) from [<
c02f9080>] (driver_detach+0xb4/0xb8)
[<
c02f9080>] (driver_detach) from [<
c02f8480>] (bus_remove_driver+0x5c/0xc4)
[<
c02f8480>] (bus_remove_driver) from [<
c008c9b8>] (SyS_delete_module+0x148/0x1d8)
[<
c008c9b8>] (SyS_delete_module) from [<
c000ef80>] (ret_fast_syscall+0x0/0x48)
FIX kmalloc-128: Object at 0xed08e8d0 not freed
Fixes:
fcb0ee6a3d33 (clk: Implement clk_unregister)
Cc: Jiada Wang <jiada_wang@mentor.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@vger.kernel.org
Mike Turquette [Fri, 25 Apr 2014 15:33:28 +0000 (08:33 -0700)]
Merge tag 'socfpga-clk-fix-for-3.15' of git://git.rocketboards.org/linux-socfpga-next into clk-fixes-socfpga
clk: socfpga: clock fix for v3.15
Currently on 3.15-rc1, the SOCFPGA platform is unable to boot. This patch
fixes the issue and allows the platform to boot.
Dinh Nguyen [Mon, 14 Apr 2014 12:59:32 +0000 (07:59 -0500)]
clk: socfpga: fix clock driver for 3.15
commit [
1771b10d6 clk: respect the clock dependencies in of_clk_init]
exposed a flaw in the socfpga clock driver and prevents the platform
from booting on 3.15-rc1.
Because the "altr,clk-mgr" is not really a clock, it should not be using
CLK_OF_DECLARE, instead we should be mapping the clk-mgr's base address
one of the functional clock init function. Use the socfpga_pll_init function
to map the clk_mgr_base_addr as this clock should always be initialized first.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Tested-by: Pavel Machek <pavel@denx.de>
Maxime COQUELIN [Wed, 29 Jan 2014 16:24:06 +0000 (17:24 +0100)]
clk: divider: Fix best div calculation for power-of-two and table dividers
The divider returned by clk_divider_bestdiv() is likely to be invalid in case
of power-of-two and table dividers when CLK_SET_RATE_PARENT flag isn't set.
Fixes boot on STiH416 platform.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: trivial merge conflict & updated changelog]
Alex Elder [Mon, 7 Apr 2014 13:22:12 +0000 (08:22 -0500)]
clk: bcm281xx: don't use unnamed structs or unions
The Broadcom Kona clock code, as originally written, made use of
unnamed union and struct fields. This is a feature present in C11,
and is a GNU extension otherwise. It worked very well for me.
Unfortunately, Russell King reported that this feature was not
supported in a build environment he used, which meant attempting
to build this code failed spectacularly.
Add names to these unnamed fields, and update the code accordingly.
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Linus Torvalds [Mon, 28 Apr 2014 02:29:27 +0000 (19:29 -0700)]
Linux 3.15-rc3
Will Deacon [Wed, 23 Apr 2014 16:52:52 +0000 (17:52 +0100)]
word-at-a-time: avoid undefined behaviour in zero_bytemask macro
The asm-generic, big-endian version of zero_bytemask creates a mask of
bytes preceding the first zero-byte by left shifting ~0ul based on the
position of the first zero byte.
Unfortunately, if the first (top) byte is zero, the output of
prep_zero_mask has only the top bit set, resulting in undefined C
behaviour as we shift left by an amount equal to the width of the type.
As it happens, GCC doesn't manage to spot this through the call to fls(),
but the issue remains if architectures choose to implement their shift
instructions differently.
An example would be arch/arm/ (AArch32), where LSL Rd, Rn, #32 results
in Rd == 0x0, whilst on arch/arm64 (AArch64) LSL Xd, Xn, #64 results in
Xd == Xn.
Rather than check explicitly for the problematic shift, this patch adds
an extra shift by 1, replacing fls with __fls. Since zero_bytemask is
never called with a zero argument (has_zero() is used to check the data
first), we don't need to worry about calling __fls(0), which is
undefined.
Cc: <stable@vger.kernel.org>
Cc: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 27 Apr 2014 22:08:12 +0000 (15:08 -0700)]
Merge branch 'safe-dirty-tlb-flush'
This merges the patch to fix possible loss of dirty bit on munmap() or
madvice(DONTNEED). If there are concurrent writers on other CPU's that
have the unmapped/unneeded page in their TLBs, their writes to the page
could possibly get lost if a third CPU raced with the TLB flush and did
a page_mkclean() before the page was fully written.
Admittedly, if you unmap() or madvice(DONTNEED) an area _while_ another
thread is still busy writing to it, you deserve all the lost writes you
could get. But we kernel people hold ourselves to higher quality
standards than "crazy people deserve to lose", because, well, we've seen
people do all kinds of crazy things.
So let's get it right, just because we can, and we don't have to worry
about it.
* safe-dirty-tlb-flush:
mm: split 'tlb_flush_mmu()' into tlb flushing and memory freeing parts
Linus Torvalds [Sun, 27 Apr 2014 20:26:28 +0000 (13:26 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: limit the path size in send to PATH_MAX
Btrfs: correctly set profile flags on seqlock retry
Btrfs: use correct key when repeating search for extent item
Btrfs: fix inode caching vs tree log
Btrfs: fix possible memory leaks in open_ctree()
Btrfs: avoid triggering bug_on() when we fail to start inode caching task
Btrfs: move btrfs_{set,clear}_and_info() to ctree.h
btrfs: replace error code from btrfs_drop_extents
btrfs: Change the hole range to a more accurate value.
btrfs: fix use-after-free in mount_subvol()
Linus Torvalds [Sun, 27 Apr 2014 19:55:04 +0000 (12:55 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull arm fixes from Russell King:
"A number of fixes for the PJ4/iwmmxt changes which arm-soc forced me
to take during the merge window. This stuff should have been better
tested and sorted out *before* the merge window"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8042/1: iwmmxt: allow to build iWMMXt on Marvell PJ4B
ARM: 8041/1: pj4: fix cpu_is_pj4 check
ARM: 8040/1: pj4: properly detect existence of iWMMXt coprocessor
ARM: 8039/1: pj4: enable iWMMXt only if CONFIG_IWMMXT is set
ARM: 8038/1: iwmmxt: explicitly check for supported architectures
Linus Torvalds [Sun, 27 Apr 2014 19:54:05 +0000 (12:54 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- compat renameat2 syscall wiring and __NR_compat_syscalls fix
- TLB fix for transparent huge pages following switch to generic
mmu_gather
- spinlock initialisation for init_mm's context
- move of_clk_init() earlier
- Kconfig duplicate entry fix
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: init: Move of_clk_init to time_init
arm64: initialize spinlock for init_mm's context
arm64: debug: remove noisy, pointless warning
arm64: mm: Add THP TLB entries to general mmu_gather
arm64: add renameat2 compat syscall
ARM64: Remove duplicated Kconfig entry for "kernel/power/Kconfig"
arm64: __NR_compat_syscalls fix
Linus Torvalds [Sun, 27 Apr 2014 18:21:03 +0000 (11:21 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A slighlty large fix for a subtle issue in the CPU hotplug code of
certain ARM SoCs, where the not yet online cpu needs to setup the cpu
local timer and needs to set the interrupt affinity to itself.
Setting interrupt affinity to a not online cpu is prohibited and
therefor the timer interrupt ends up on the wrong cpu, which leads to
nasty complications.
The SoC folks tried to hack around that in the SoC code in some more
than nasty ways. The proper solution is to have a way to enforce the
affinity setting to a not online cpu. The core patch to the genirq
code provides that facility and the follow up patches make use of it
in the GIC interrupt controller and the exynos timer driver.
The change to the core code has no implications to existing users,
except for the rename of the locked function and therefor the
necessary fixup in mips/cavium. Aside of that, no runtime impact is
possible, as none of the existing interrupt chips implements anything
which depends on the force argument of the irq_set_affinity()
callback"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Exynos_mct: Register clock event after request_irq()
clocksource: Exynos_mct: Use irq_force_affinity() in cpu bringup
irqchip: Gic: Support forced affinity setting
genirq: Allow forcing cpu affinity of interrupts
Linus Torvalds [Sun, 27 Apr 2014 17:39:09 +0000 (10:39 -0700)]
Merge tag 'tty-3.15-rc3' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few tty/serial fixes for 3.15-rc3 that resolve a number of
reported issues in the 8250 and samsung serial drivers, as well as a
character loss fix for the tty core that was caused by the lock
removal patches a release ago"
* tag 'tty-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial_core: fix uart PORT_UNKNOWN handling
serial: samsung: Change barrier() to cpu_relax() in console output
serial: samsung: don't check config for every character
serial: samsung: Use the passed in "port", fixing kgdb w/ no console
serial: 8250: Fix thread unsafe __dma_tx_complete function
8250_core: Fix unwanted TX chars write
tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc
Linus Torvalds [Sun, 27 Apr 2014 17:34:29 +0000 (10:34 -0700)]
Merge tag 'staging-3.15-rc3' of git://git./linux/kernel/git/gregkh/staging
Pull staging / IIO driver fixes from Greg KH:
"Here are some small staging and IIO driver fixes for 3.15-rc3.
Nothing major at all, just some assorted issues that people have
reported"
* tag 'staging-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: usbdux: bug fix for accessing 'ao_chanlist' in private data
iio: adc: mxs-lradc: fix warning when buidling on avr32
iio: cm36651: Fix i2c client leak and possible NULL pointer dereference
iio: querying buffer scan_mask should return 0/1
staging:iio:ad2s1200 fix a missing break
iio: adc: at91_adc: correct default shtim value
ARM: at91: at91sam9260: change at91_adc name
ARM: at91: at91sam9g45: change at91_adc name
iio: cm32181: Fix read integration time function
iio: adc: at91_adc: Repair broken platform_data support
Linus Torvalds [Sun, 27 Apr 2014 17:28:34 +0000 (10:28 -0700)]
Merge tag 'driver-core-3.15-rc3' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some kernfs fixes for 3.15-rc3 that resolve some reported
problems. Nothing huge, but all needed"
* tag 'driver-core-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
s390/ccwgroup: Fix memory corruption
kernfs: add back missing error check in kernfs_fop_mmap()
kernfs: fix a subdir count leak
Linus Torvalds [Sun, 27 Apr 2014 17:24:17 +0000 (10:24 -0700)]
Merge tag 'usb-3.15-rc3' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 3.15-rc3. The majority are gadget
fixes, as we didn't get any of those in for 3.15-rc2. The others are
all over the place, and there's a number of new device id addtions as
well."
* tag 'usb-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: option: add and update a number of CMOTech devices
usb: option: add Alcatel L800MA
usb: option: add Olivetti Olicard 500
usb: qcserial: add Sierra Wireless MC7305/MC7355
usb: qcserial: add Sierra Wireless MC73xx
usb: qcserial: add Sierra Wireless EM7355
USB: io_ti: fix firmware download on big-endian machines
usb/xhci: fix compilation warning when !CONFIG_PCI && !CONFIG_PM
xhci: extend quirk for Renesas cards
xhci: Switch Intel Lynx Point ports to EHCI on shutdown.
usb: xhci: Prefer endpoint context dequeue pointer over stopped_trb
phy: core: make NULL a valid phy reference if !CONFIG_GENERIC_PHY
phy: fix kernel oops in phy_lookup()
phy: restore OMAP_CONTROL_PHY dependencies
phy: exynos: fix building as a module
USB: serial: fix sysfs-attribute removal deadlock
usb: wusbcore: fix panic in wusbhc_chid_set
usb: wusbcore: convert nested lock to use spin_lock instead of spin_lock_irq
uwb: don't call spin_unlock_irq in a USB completion handler
usb: chipidea: coordinate usb phy initialization for different phy type
...
Linus Torvalds [Sun, 27 Apr 2014 17:19:06 +0000 (10:19 -0700)]
Merge tag 'pm+acpi-3.15-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These include a fix for a recent ACPI regression related to device
notifications, intel_idle fix related to IvyTown support, fix for a
buffer size issue in ACPICA, PM core fix related to the "freeze" sleep
state, four fixes for various types of breakage in cpufreq drivers, a
PNP workaround for a wrong memory region size in ACPI tables, and a
fix and cleanup for the ACPI tools Makefile.
Specifics:
- Fix for broken ACPI notifications on some systems caused by a
recent ACPI hotplug commit that blocked the propagation of unknown
type notifications to device drivers inadvertently.
- intel_idle fix to make the IvyTown C-states handling (added
recently) work as intended which now is broken due to missing
braces. From Christoph Jaeger.
- ACPICA fix to make it allocate buffers of the right sizes for the
Generic Serial Bus operation region access. From Lv Zheng.
- PM core fix unblocking cpuidle before entering the "freeze" sleep
state which causes that state to be able to actually save more
energy than runtime idle.
- Configuration and build fixes for the highbank and powernv cpufreq
drivers from Kefeng Wang and Srivatsa S Bhat.
- Coccinelle warning fix related to error pointers for the unicore32
cpufreq driver from Duan Jiong.
- Integer overflow fix for the ppc-corenet cpufreq driver from Geert
Uytterhoeven.
- Workaround for BIOSes that don't report the entire Intel MCH area
in their ACPI tables from Bjorn Helgaas.
- ACPI tools Makefile fix and cleanup from Thomas Renninger"
* tag 'pm+acpi-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / notify: Do not block unknown type notifications in root handler
PNP: Work around BIOS defects in Intel MCH area reporting
cpufreq: highbank: fix ARM_HIGHBANK_CPUFREQ dependency warning
cpufreq: ppc: Fix integer overflow in expression
cpufreq, powernv: Fix build failure on UP
cpufreq: unicore32: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
PM / suspend: Make cpuidle work in the "freeze" state
intel_idle: fix IVT idle state table setting
ACPICA: Fix buffer allocation issue for generic_serial_bus region accesses.
tools/power/acpi: Minor bugfixes
Chris Mason [Sat, 26 Apr 2014 12:02:03 +0000 (05:02 -0700)]
Btrfs: limit the path size in send to PATH_MAX
fs_path_ensure_buf is used to make sure our path buffers for
send are big enough for the path names as we construct them.
The buffer size is limited to 32K by the length field in
the struct.
But bugs in the path construction can end up trying to build
a huge buffer, and we'll do invalid memmmoves when the
buffer length field wraps.
This patch is step one, preventing the overflows.
Signed-off-by: Chris Mason <clm@fb.com>
Thomas Petazzoni [Tue, 22 Apr 2014 21:26:08 +0000 (23:26 +0200)]
clk: mvebu: add Orion5x clock driver
This commit adds a core clock driver for the Orion5x SoC, with support
for the tclk, the CPU frequency and the DDR frequency. All the details
about the Sample-At-Reset register were extracted from the U-Boot
sources for Orion5x.
Note that Orion5x does not have gatable clocks, so this core clock
driver is sufficient to support clocking on Orion5x platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1398202002-28530-5-git-send-email-thomas.petazzoni@free-electrons.com
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Linus Torvalds [Fri, 25 Apr 2014 23:05:40 +0000 (16:05 -0700)]
mm: split 'tlb_flush_mmu()' into tlb flushing and memory freeing parts
The mmu-gather operation 'tlb_flush_mmu()' has done two things: the
actual tlb flush operation, and the batched freeing of the pages that
the TLB entries pointed at.
This splits the operation into separate phases, so that the forced
batched flushing done by zap_pte_range() can now do the actual TLB flush
while still holding the page table lock, but delay the batched freeing
of all the pages to after the lock has been dropped.
This in turn allows us to avoid a race condition between
set_page_dirty() (as called by zap_pte_range() when it finds a dirty
shared memory pte) and page_mkclean(): because we now flush all the
dirty page data from the TLB's while holding the pte lock,
page_mkclean() will be held up walking the (recently cleaned) page
tables until after the TLB entries have been flushed from all CPU's.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Dave Hansen <dave.hansen@intel.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafael J. Wysocki [Fri, 25 Apr 2014 22:40:25 +0000 (00:40 +0200)]
Merge branches 'pnp' and 'acpi-hotplug'
* pnp:
PNP: Work around BIOS defects in Intel MCH area reporting
* acpi-hotplug:
ACPI / notify: Do not block unknown type notifications in root handler
Linus Torvalds [Fri, 25 Apr 2014 20:12:25 +0000 (13:12 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- ltc2945: Don't unecessarily crash kernel on implementation error
- vexpress: Fix 'name' and 'label' attributes
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ltc2945) Don't crash the kernel unnecessarily
hwmon: (vexpress) Avoid creating non-existing attributes
hwmon: (vexpress) Use legal hwmon device names
Linus Torvalds [Fri, 25 Apr 2014 20:07:24 +0000 (13:07 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of seven fixes, three (hpsa) and free'd command
references correcting bugs in the last round of updates and the
remaining four correcting problems within the SCSI error handler that
was causing a deadlock within USB"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] More USB deadlock fixes
[SCSI] Fix USB deadlock caused by SCSI error handling
[SCSI] Fix command result state propagation
[SCSI] Fix spurious request sense in error handling
[SCSI] don't reference freed command in scsi_prep_return
[SCSI] don't reference freed command in scsi_init_sgtable
[SCSI] hpsa: fix NULL dereference in hpsa_put_ctlr_into_performant_mode()
Linus Torvalds [Fri, 25 Apr 2014 20:02:02 +0000 (13:02 -0700)]
Merge tag 'fixes-3.15-rc3' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Since we didn't get around to collect fixes in time for -rc2 over the
easter vacation, this one is unfortunately a bit larger than we'd like
for an -rc3 merge.
A large set of the changes is in the device tree sources, so I'm
splitting out the description between code changes and DT changes.
Aside from omap and versatile express, the actual code bugs are and
trivial. Here is an overview:
imx:
- fix video clock settings
- fix one clock refcounting bug
omap:
- update defconfig for renamed USB PHY driver
- fix error handling in gpmc
- fix N900 video initialization regression
- fix reression in hwmod code from missing braces
- fix am43xx and omap3 clocks
- remove bogus write to voltage control register
pxa:
- fix build regression from 3.13 header cleanup
rockchip:
- fix a misleading printk string
shmobile:
- fix incorrect sound setting on multiple machines
spear:
- remove incorrect __init section annotation
tegra:
- remove a stale Kconfig entry
u300:
- update defconfig
ux500:
- enable common wireless and sensor drivers in defconfig
- more defconfig updates
vexpress:
- fix voltage calculation for opp
- fix reboot hang and warning
- fix out-of-bounds array access
- improve error handling in clock driver
overall:
- always select CLKSRC_OF in multiplatform builds
And these are the devicetree related changes:
imx:
- add missing #clock-cell properties
- fix pinctrl setting in imx6sl-evk
- fix video endpoint on imx53
- remove obsolete lvds-channel nodes (multiple patches)
- add missing second stmpe node
- fix usb host mode on dmo-edmqmx6 (multiple patches)
- fix gic node #address-cells to match usage
- add missing legacy IRQ map for PCIe
- fix microsom pincontrol setting for rgmii
- fix fatal typo in touchscreen DT usage for mx5
- list all RAM present on m53evk and mx53qsb
omap:
- fix bug in DT handling of gpmc external bus
- add DT for older revision of beagleboard
- fix regression after DT node name fixes
- remove obsolete properties for gpmc
- fix pinmux comment to match DT it refers to
- fix newly added dra7xx clock node data
- add missing clock for USB PHY
mvebu:
- add missing clock for mdio node
- fix nonstandard vendor prefixes on i2c nodes
rockchip:
- fix pin control setting for uart
shmobile:
- fix typo in DT data for pin control (multiple patches)
- fix gic node #address-cells to match usage
tegra:
- fix clock and uart DT representation to match hardware
zynq:
- add DT nodes for newly added driver
- add DT properties required for cpufreq-ondemand
overall:
- restore alphabetic order in Makefile
- grammar fixes in bindings"
* tag 'fixes-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (66 commits)
ARM: vexpress/TC2: Convert OPP voltage to uV before storing
power/reset: vexpress: Fix restart/power off operation
dt: tegra: remove non-existent clock IDs
clk: tegra: remove non-existent clocks
ARM: tegra: remove UART5/UARTE from tegra124.dtsi
ARM: tegra: remove TEGRA_EMC_SCALING_ENABLE
ARM: Tidy up DTB Makefile entries
ARM: fix missing CLKSRC_OF on multi-platform
ARM: spear: add __init to spear_clocksource_init()
ARM: pxa: hx4700.h: include "irqs.h" for PXA_NR_BUILTIN_GPIO
arm/mach-vexpress: array accessed out of bounds
clk: vexpress: NULL dereference on error path
ARM: OMAP2+: Fix GPMC remap for devices using an offset
ARM: zynq: dt: Add I2C nodes to Zynq device tree
ARM: zynq: DT: Add 'clock-latency' property
ARM: OMAP2+: Fix oops for GPMC free
ARM: dts: Add support for the BeagleBoard xM A/B
ARM: dts: Grammar /that will/it will/
ARM: dts: Grammar /is uses/ is used/
ARM: OMAP2+: Fix config name for USB3 PHY
...
Linus Torvalds [Fri, 25 Apr 2014 19:40:32 +0000 (12:40 -0700)]
Merge tag 'locks-v3.15-2' of git://git.samba.org/jlayton/linux
Pull file locking fixes from Jeff Layton:
"File locking related bugfixes for v3.15 (pile #2)
- fix for a long-standing bug in __break_lease that can cause soft
lockups
- renaming of file-private locks to "open file description" locks,
and the command macros to more visually distinct names
The fix for __break_lease is also in the pile of patches for which
Bruce sent a pull request, but I assume that your merge procedure will
handle that correctly.
For the other patches, I don't like the fact that we need to rename
this stuff at this late stage, but it should be settled now
(hopefully)"
* tag 'locks-v3.15-2' of git://git.samba.org/jlayton/linux:
locks: rename FL_FILE_PVT and IS_FILE_PVT to use "*_OFDLCK" instead
locks: rename file-private locks to "open file description locks"
locks: allow __break_lease to sleep even when break_time is 0
Linus Torvalds [Fri, 25 Apr 2014 19:39:05 +0000 (12:39 -0700)]
Merge branch 'for-3.15' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"Three small nfsd bugfixes (including one locks.c fix for a bug
triggered only from nfsd).
Jeff's patches are for long-existing problems that became easier to
trigger since the addition of vfs delegation support"
* 'for-3.15' of git://linux-nfs.org/~bfields/linux:
Revert "nfsd4: fix nfs4err_resource in 4.1 case"
nfsd: set timeparms.to_maxval in setup_callback_client
locks: allow __break_lease to sleep even when break_time is 0
Christian Borntraeger [Wed, 23 Apr 2014 18:58:45 +0000 (20:58 +0200)]
s390/ccwgroup: Fix memory corruption
commit
0b60f9ead5d4816e7e3d6e28f4a0d22d4a1b2513 (s390: use
device_remove_file_self() instead of device_schedule_callback())
caused random memory corruption on my s390 box. Turns out that the
last element of the ccwgroup structure is of dynamic size, so we
must move the newly introduced work structure _before_ the zero
length array.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Tejun Heo <tj@kernel.org>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Sun, 20 Apr 2014 12:29:21 +0000 (08:29 -0400)]
kernfs: add back missing error check in kernfs_fop_mmap()
While updating how mmap enabled kernfs files are handled by lockdep,
9b2db6e18945 ("sysfs: bail early from kernfs_file_mmap() to avoid
spurious lockdep warning") inadvertently dropped error return check
from kernfs_file_mmap(). The intention was just dropping "if
(ops->mmap)" check as the control won't reach the point if the mmap
callback isn't implemented, but I mistakenly removed the error return
check together with it.
This led to Xorg crash on i810 which was reported and bisected to the
commit and then to the specific change by Tobias.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-bisected-by: Tobias Powalowski <tobias.powalowski@googlemail.com>
Tested-by: Tobias Powalowski <tobias.powalowski@googlemail.com>
References: http://lkml.kernel.org/g/
533D01BD.
1010200@googlemail.com
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jianyu Zhan [Thu, 17 Apr 2014 09:52:10 +0000 (17:52 +0800)]
kernfs: fix a subdir count leak
Currently kernfs_link_sibling() increates parent->dir.subdirs before
adding the node into parent's chidren rb tree.
Because it is possible that kernfs_link_sibling() couldn't find
a suitable slot and bail out, this leads to a mismatch between
elevated subdir count with actual children node numbers.
This patches fix this problem, by moving the subdir accouting
after the actual addtion happening.
Signed-off-by: Jianyu Zhan <nasa4836@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Fri, 25 Apr 2014 16:49:20 +0000 (18:49 +0200)]
usb: option: add and update a number of CMOTech devices
A number of older CMOTech modems are based on Qualcomm
chips. The blacklisted interfaces are QMI/wwan.
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Fri, 25 Apr 2014 16:49:19 +0000 (18:49 +0200)]
usb: option: add Alcatel L800MA
Device interface layout:
0: ff/ff/ff - serial
1: ff/00/00 - serial AT+PPP
2: ff/ff/ff - QMI/wwan
3: 08/06/50 - storage
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Fri, 25 Apr 2014 16:49:18 +0000 (18:49 +0200)]
usb: option: add Olivetti Olicard 500
Device interface layout:
0: ff/ff/ff - serial
1: ff/ff/ff - serial AT+PPP
2: 08/06/50 - storage
3: ff/ff/ff - serial
4: ff/ff/ff - QMI/wwan
Cc: <stable@vger.kernel.org>
Reported-by: Julio Araujo <julio.araujo@wllctel.com.br>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Fri, 25 Apr 2014 16:49:17 +0000 (18:49 +0200)]
usb: qcserial: add Sierra Wireless MC7305/MC7355
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Fri, 25 Apr 2014 16:49:16 +0000 (18:49 +0200)]
usb: qcserial: add Sierra Wireless MC73xx
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Fri, 25 Apr 2014 16:49:15 +0000 (18:49 +0200)]
usb: qcserial: add Sierra Wireless EM7355
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chanho Min [Mon, 14 Apr 2014 07:38:53 +0000 (08:38 +0100)]
arm64: init: Move of_clk_init to time_init
Clock providers should be initialized before clocksource_of_init.
If not, Clock source initialization can be fail to get the clock.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Johan Hovold [Fri, 25 Apr 2014 13:23:03 +0000 (15:23 +0200)]
USB: io_ti: fix firmware download on big-endian machines
During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.
Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
Reported-by: Ludovic Drolez <ldrolez@debian.org>
Tested-by: Ludovic Drolez <ldrolez@debian.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Cohen [Fri, 25 Apr 2014 16:20:16 +0000 (19:20 +0300)]
usb/xhci: fix compilation warning when !CONFIG_PCI && !CONFIG_PM
When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]
Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.
This warning has been in since 3.2 kernel and was
caused by commit
421aa841a134f6a743111cf44d0c6d3b45e3cf8c
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Cc: stable@vger.kernel.org # 3.2
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Igor Gnatenko [Fri, 25 Apr 2014 16:20:15 +0000 (19:20 +0300)]
xhci: extend quirk for Renesas cards
After suspend another Renesas PCI-X USB 3.0 card doesn't work.
[root@fedora-20 ~]# lspci -vmnnd 1912:
Device: 03:00.0
Class: USB controller [0c03]
Vendor: Renesas Technology Corp. [1912]
Device: uPD720202 USB 3.0 Host Controller [0015]
SVendor: Renesas Technology Corp. [1912]
SDevice: uPD720202 USB 3.0 Host Controller [0015]
Rev: 02
ProgIf: 30
This patch should be applied to stable kernel 3.14 that contain
the commit
1aa9578c1a9450fb21501c4f549f5b1edb557e6d
"xhci: Fix resume issues on Renesas chips in Samsung laptops"
Reported-and-tested-by: Anatoly Kharchenko <rfr-bugs@yandex.ru>
Reference: http://redmine.russianfedora.pro/issues/1315
Signed-off-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Denis Turischev [Fri, 25 Apr 2014 16:20:14 +0000 (19:20 +0300)]
xhci: Switch Intel Lynx Point ports to EHCI on shutdown.
The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.
This patch should be backported to stable kernels as old as 3.12,
that contain the commit
638298dc66ea36623dbc2757a24fc2c4ab41b016
"xhci: Fix spurious wakeups after S5 on Haswell"
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julius Werner [Fri, 25 Apr 2014 16:20:13 +0000 (19:20 +0300)]
usb: xhci: Prefer endpoint context dequeue pointer over stopped_trb
We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.
The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.
This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.
This patch should be backported to kernels as old as 2.6.31 that contain
the commit
ae636747146ea97efa18e04576acd3416e2514f5 "USB: xhci: URB
cancellation support."
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leo Yan [Wed, 16 Apr 2014 12:26:35 +0000 (13:26 +0100)]
arm64: initialize spinlock for init_mm's context
ARM64 has defined the spinlock for init_mm's context, so need initialize
the spinlock structure; otherwise during the suspend flow it will dump
the info for spinlock's bad magic warning as below:
[ 39.084394] Disabling non-boot CPUs ...
[ 39.092871] BUG: spinlock bad magic on CPU#1, swapper/1/0
[ 39.092896] lock: init_mm+0x338/0x3e0, .magic:
00000000, .owner: <none>/-1, .owner_cpu: 0
[ 39.092907] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G O 3.10.33 #125
[ 39.092912] Call trace:
[ 39.092927] [<
ffffffc000087e64>] dump_backtrace+0x0/0x16c
[ 39.092934] [<
ffffffc000087fe0>] show_stack+0x10/0x1c
[ 39.092947] [<
ffffffc000765334>] dump_stack+0x1c/0x28
[ 39.092953] [<
ffffffc0007653b8>] spin_dump+0x78/0x88
[ 39.092960] [<
ffffffc0007653ec>] spin_bug+0x24/0x34
[ 39.092971] [<
ffffffc000300a28>] do_raw_spin_lock+0x98/0x17c
[ 39.092979] [<
ffffffc00076cf08>] _raw_spin_lock_irqsave+0x4c/0x60
[ 39.092990] [<
ffffffc000094044>] set_mm_context+0x1c/0x6c
[ 39.092996] [<
ffffffc0000941c8>] __new_context+0x94/0x10c
[ 39.093007] [<
ffffffc0000d63d4>] idle_task_exit+0x104/0x1b0
[ 39.093014] [<
ffffffc00008d91c>] cpu_die+0x14/0x74
[ 39.093021] [<
ffffffc000084f74>] arch_cpu_idle_dead+0x8/0x14
[ 39.093030] [<
ffffffc0000e7f18>] cpu_startup_entry+0x1ec/0x258
[ 39.093036] [<
ffffffc00008d810>] secondary_start_kernel+0x114/0x124
Signed-off-by: Leo Yan <leoy@marvell.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Thu, 17 Apr 2014 11:37:14 +0000 (12:37 +0100)]
arm64: debug: remove noisy, pointless warning
Sending a SIGTRAP to a user task after execution of a BRK instruction at
EL0 is fundamental to the way in which software breakpoints work and
doesn't deserve a warning to be logged in dmesg. Whilst the warning can
be justified from EL1, do_debug_exception will already do the right thing,
so simply remove the code altogether.
Cc: Sandeepa Prabhu <sandeepa.prabhu@linaro.org>
Reported-by: Kyrylo Tkachov <kyrylo.tkachov@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Steve Capper [Thu, 24 Apr 2014 14:33:21 +0000 (15:33 +0100)]
arm64: mm: Add THP TLB entries to general mmu_gather
When arm64 moved over to the core mmu_gather, it lost the logic to
flush THP TLB entries (tlb_remove_pmd_tlb_entry was removed and the
core implementation only signals that the mmu_gather needs a flush).
This patch ensures that tlb_add_flush is called for THP TLB entries.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Sebastian Hesselbarth [Thu, 24 Apr 2014 21:58:30 +0000 (22:58 +0100)]
ARM: 8042/1: iwmmxt: allow to build iWMMXt on Marvell PJ4B
Some Marvell PJ4B CPUs also implement iWMMXt extensions. With a
proper check for iWMMXt coprocessors now in place, enable it by
default on PJ4B. While at it, also allow to manually select
the corresponding Kconfig option.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sebastian Hesselbarth [Thu, 24 Apr 2014 21:58:00 +0000 (22:58 +0100)]
ARM: 8041/1: pj4: fix cpu_is_pj4 check
Commit
fdb487f5c961b94486a78fa61fa28b8eff1954ab
("ARM: 8015/1: Add cpu_is_pj4 to distinguish PJ4 because it
has some differences with V7")
introduced a cpuid check for Marvell PJ4 processors to fix a
regression caused by adding PJ4 based Marvell Dove into
multi_v7.
Unfortunately, this check is too narrow to catch PJ4 used on
Dove itself and breaks iWMMXt support.
This patch therefore relaxes the cpuid mask to match both PJ4
and PJ4B. Also, rework the given comment about PJ4/PJ4B
modifications to be a little bit more specific about the
differences.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sebastian Hesselbarth [Thu, 24 Apr 2014 21:57:25 +0000 (22:57 +0100)]
ARM: 8040/1: pj4: properly detect existence of iWMMXt coprocessor
commit
fdb487f5c961b94486a78fa61fa28b8eff1954ab
("ARM: 8015/1: Add cpu_is_pj4 to distinguish PJ4 because it
has some differences with V7")
introduced a fix for checking PJ4 cpuid to not use PJ4 specific
coprocessor access on non-PJ4 platforms.
Unfortunately, this in turn broke Marvell Armada 370/XP, both
comprising Marvell PJ4B CPUs without iWMMXt extension. Instead
of only checking for cpuid, which may not be sufficient to
determine iWMMXt support, the presence of iWMMXt coprocessors
can be checked by enabling and reading the Coprocessor ID
register (wCID, register 0 of CP1).
Therefore this adds an explicit check for the presence and correct
wCID value, before enabling iWMMXt capabilities. As a bonus, also
print the iWMMXt version of a detected coprocessor.
This has been tested to properly detect iWMMXt presence/absence on:
- PJ4, CPUID 0x560f5815, wCID 0x56052001: Marvell Dove, iWMMXt v2
- PJ4B, CPUID 0x561f5811: Marvell Armada 370, no iWMMXt
- PJ4B, CPUID 0x562f5841, wCID 0x56052001: Marvell Armada 1500, iWMMXt v2
- PJ4B, CPUID 0x562f5842: Marvell Armada XP, no iWMMXt
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sebastian Hesselbarth [Thu, 24 Apr 2014 21:56:43 +0000 (22:56 +0100)]
ARM: 8039/1: pj4: enable iWMMXt only if CONFIG_IWMMXT is set
This fixes PJ4 coprocessor init to only expose iWMMXt capabilities,
if the corresponding kernel support for iWMMXt is enabled.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sebastian Hesselbarth [Thu, 24 Apr 2014 21:54:58 +0000 (22:54 +0100)]
ARM: 8038/1: iwmmxt: explicitly check for supported architectures
iwmmxt.S requires special treatment of coprocessor access registers
for PJ4 and XScale-based CPUs. It only checks for CPU_PJ4 and drops
down to XScale-based treatment on all other architectures.
As some PJ4B also come with iWMMXt and also need PJ4 treatment,
rework the corresponding preprocessor directives to explicitly
check for supported architectures and fail on unsupported ones.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>