OSDN Git Service
Wen Gong [Mon, 8 Oct 2018 09:02:43 +0000 (17:02 +0800)]
ath10k: add peer flush in ath10k_flush for STATION
In the noisy environment, if there are packets in the queue and can't
send out, the suspend timing will be more than 5 seconds due to the wait,
flush the queue to optimize the suspend timing, and let the upper layer to
retry the packets after resume.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI.
It's not a regression with new firmware releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Gustavo A. R. Silva [Fri, 5 Oct 2018 18:56:23 +0000 (20:56 +0200)]
ath10k: remove unnecessary comparison of unsigned integer with < 0
There is no need to compare *ps_state_enable* with < 0 because
such variable is of type u8 (8 bits, unsigned), making it
impossible to hold a negative value.
Fix this by removing such comparison.
Addresses-Coverity-ID:
1473921 ("Unsigned compared against 0")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Gustavo A. R. Silva [Fri, 5 Oct 2018 18:42:45 +0000 (20:42 +0200)]
ath10k: htt_rx: fix signedness bug in ath10k_update_per_peer_tx_stats
Currently, the error handling for the call to function
ath10k_get_legacy_rate_idx() doesn't work because
*rate_idx* is of type u8 (8 bits, unsigned), which
makes it impossible for it to hold a value less
than 0.
Fix this by changing the type of variable *rate_idx*
to s8 (8 bits, signed).
Addresses-Coverity-ID:
1473914 ("Unsigned compared against 0")
Fixes:
0189dbd71cbd ("ath10k: get the legacy rate index to update the txrate table")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Balaji Pothunoori [Mon, 10 Sep 2018 06:24:30 +0000 (11:54 +0530)]
ath10k: management tx ack rssi capability check
Adding WMI service check for management tx ack rssi support; this is
done to maintain common avg ack signal in user level for both data
and management tx ack packet.
Tested on QCA4019(fw version-10.4-3.2.1-00063).
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Thu, 4 Oct 2018 05:45:31 +0000 (08:45 +0300)]
ath10k: support NET_DETECT WoWLAN feature
For WoWLAN support it is expected to support wake up based on discovery of
one or more known SSIDs. This is the WIPHY_WOWLAN_NET_DETECT feature,
which shows up as an NL80211 feature flag.
This shows up in 'iw phy' as:
WoWLAN support:
* wake up on network detection, up to 16 match sets
And it can be enabled with command:
iw phy0 wowlan enable net-detect interval 5000 delay 30 freqs 2412 matches ssid foo
Firmware will do scan by the configured parameters after suspend and
wakeup if it found matched SSIDs. Tested with QCA6174 hw3.0 with
firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[kvalo@codeaurora.org: fix lots of endian bugs, whitespace, commit log and style cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Tue, 2 Oct 2018 18:03:13 +0000 (23:33 +0530)]
ath10k: set probe request oui during driver start
Currently the wmi command for setting probe request
oui, needed for mac randomization, is sent during
the mac register. At this time, during the driver
init the wmi has already been detached. This can
cause unexpected behavior since the firmware is
already down and the wmi has been detached.
Send the wmi command for setting probe request
oui during the driver start. This will make sure
that the firmware is started and wmi is initialized
before we send this command.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes:
60e1d0fb290197fe505dff6e4e3b7e4d258dbf60
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sriram R [Wed, 3 Oct 2018 03:13:50 +0000 (08:43 +0530)]
ath10k: fix possible out of bound access of ath10k_rates array
While using 'ath10k_mac_get_rate_hw_value()' to obtain the hw value
from the passed bitrate, there is a chance of out of bound array access
when wrong bitrate is passed. This is fixed by comparing the bitrates
within the correct size of the ath10k_rates array.
Fixes commit
f279294e9ee2 ("ath10k: add support for configuring management
packet rate"). Also correction made to some indents used in the above commit.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Thu, 4 Oct 2018 05:35:58 +0000 (08:35 +0300)]
Merge tag 'mt76-for-kvalo-2018-10-01' of https://github.com/nbd168/wireless
mt76 patches for 4.20
* unify code between mt76x0, mt76x2
* mt76x0 fixes
* tx power configuration fix for 76x2
* more progress on mt76x0e support
* support for getting firmware version via ethtool
* fix for rx buffer allocation regression on usb
* fix for handling powersave responses
* fix for mt76x2 beacon transmission
Kalle Valo [Thu, 4 Oct 2018 05:33:42 +0000 (08:33 +0300)]
Merge ath-next from git://git./linux/kernel/git/kvalo/ath.git
ath.git patches for 4.20. Major changes:
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
Vakul Garg [Sun, 30 Sep 2018 02:34:35 +0000 (08:04 +0530)]
tls: Add support for inplace records encryption
Presently, for non-zero copy case, separate pages are allocated for
storing plaintext and encrypted text of records. These pages are stored
in sg_plaintext_data and sg_encrypted_data scatterlists inside record
structure. Further, sg_plaintext_data & sg_encrypted_data are passed
to cryptoapis for record encryption. Allocating separate pages for
plaintext and encrypted text is inefficient from both required memory
and performance point of view.
This patch adds support of inplace encryption of records. For non-zero
copy case, we reuse the pages from sg_encrypted_data scatterlist to
copy the application's plaintext data. For the movement of pages from
sg_encrypted_data to sg_plaintext_data scatterlists, we introduce a new
function move_to_plaintext_sg(). This function add pages into
sg_plaintext_data from sg_encrypted_data scatterlists.
tls_do_encryption() is modified to pass the same scatterlist as both
source and destination into aead_request_set_crypt() if inplace crypto
has been enabled. A new ariable 'inplace_crypto' has been introduced in
record structure to signify whether the same scatterlist can be used.
By default, the inplace_crypto is enabled in get_rec(). If zero-copy is
used (i.e. plaintext data is not copied), inplace_crypto is set to '0'.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Reviewed-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hauke Mehrtens [Sat, 29 Sep 2018 11:26:30 +0000 (13:26 +0200)]
net: dsa: lantiq: Fix path in MAINTAINERS file
The MAINTAINERS file contained the wrong file name of the driver.
Fixes:
14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Sat, 29 Sep 2018 12:52:56 +0000 (14:52 +0200)]
hv_netvsc: remove ndo_poll_controller
Similar to other patches from ERic.
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
In netvsc driver it uses NAPI for TX completions. The default
poll_napi will do this for us now and avoid the capture.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 29 Sep 2018 19:57:02 +0000 (21:57 +0200)]
MAINTAINERS: Fix wrong include file path
Fix the patch for the mv88e6xxx.h header file in MAINTAINERS
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 3 Oct 2018 05:34:54 +0000 (22:34 -0700)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-09-30
Here's the first bluetooth-next pull request for the 4.20 kernel.
- Fixes & cleanups to hci_qca driver
- NULL dereference fix to debugfs
- Improved L2CAP Connection-oriented Channel MTU & MPS handling
- Added support for USB-based RTL8822C controller
- Added device ID for BCM4335C0 UART-based controller
- Various other smaller cleanups & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Chancellor [Mon, 1 Oct 2018 03:47:38 +0000 (20:47 -0700)]
cxgb4: Use proper enum in IEEE_FAUX_SYNC
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:390:4: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
IEEE_FAUX_SYNC(dev, dcb);
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.h:70:10: note: expanded
from macro 'IEEE_FAUX_SYNC'
CXGB4_DCB_STATE_FW_ALLSYNCED);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.
CXGB4_DCB_STATE_FW_ALLSYNCED = CXGB4_DCB_INPUT_FW_ALLSYNCED = 3
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Chancellor [Mon, 1 Oct 2018 03:51:43 +0000 (20:51 -0700)]
cxgb4: Use proper enum in cxgb4_dcb_handle_fw_update
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:303:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
? CXGB4_DCB_STATE_FW_ALLSYNCED
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:304:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
: CXGB4_DCB_STATE_FW_INCOMPLETE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2 warnings generated.
Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.
CXGB4_DCB_STATE_FW_INCOMPLETE = CXGB4_DCB_INPUT_FW_INCOMPLETE = 2
CXGB4_DCB_STATE_FW_ALLSYNCED = CXGB4_DCB_INPUT_FW_ALLSYNCED = 3
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Chancellor [Mon, 1 Oct 2018 04:10:29 +0000 (21:10 -0700)]
dpaa_eth: Remove useless declaration
Clang warns:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2734:34: warning:
tentative array definition assumed to have one element
static const struct of_device_id dpaa_match[];
^
1 warning generated.
Turns out that since this driver was introduced in commit
9ad1a3749333
("dpaa_eth: add support for DPAA Ethernet"), this declaration has been
unused. Remove it to silence the warning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Ruddy [Mon, 1 Oct 2018 08:41:27 +0000 (09:41 +0100)]
ipv6: add vrf table handling code for ipv6 mcast
The code to obtain the correct table for the incoming interface was
missing for IPv6. This has been added along with the table creation
notification to fib rules for the RTNL_FAMILY_IP6MR address family.
Signed-off-by: Patrick Ruddy <pruddy@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Mon, 1 Oct 2018 08:40:23 +0000 (09:40 +0100)]
ipv4: Allow sending multicast packets on specific i/f using VRF socket
It is useful to be able to use the same socket for listening in a
specific VRF, as for sending multicast packets out of a specific
interface. However, the bound device on the socket currently takes
precedence and results in the packets not being sent.
Relax the condition on overriding the output interface to use for
sending packets out of UDP, raw and ping sockets to allow multicast
packets to be sent using the specified multicast interface.
Signed-off-by: Robert Shearman <rshearma@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 1 Oct 2018 08:57:01 +0000 (11:57 +0300)]
bridge: mcast: Default back to multicast enabled state
Commit
13cefad2f2c1 ("net: bridge: convert and rename mcast disabled")
converted the 'multicast_disabled' field to an option bit named
'BROPT_MULTICAST_ENABLED'.
While the old field was implicitly initialized to 0, the new field is
not initialized, resulting in the bridge defaulting to multicast
disabled state and breaking existing applications.
Fix this by explicitly initializing the option.
Fixes:
13cefad2f2c1 ("net: bridge: convert and rename mcast disabled")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 3 Oct 2018 05:24:08 +0000 (22:24 -0700)]
Merge branch 'dpaa2-eth-Add-support-for-Rx-flow-classification'
Ioana Radulescu says:
====================
dpaa2-eth: Add support for Rx flow classification
The Management Complex (MC) firmware initially allowed the
configuration of a single key to be used both for Rx flow hashing
and flow classification. This prevented us from supporting
Rx flow classification independently of the hash key configuration.
Newer firmware versions expose separate commands for
configuring the two types of keys, so we can use them to
introduce Rx classification support. For frames that don't match
any classification rule, we fall back to statistical distribution
based on the current hash key.
The first patch in this set updates the Rx hashing code to use
the new firmware API for key config. Subsequent patches introduce
the firmware API for configuring the classification and actual
support for adding and deleting rules via ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Radulescu [Mon, 1 Oct 2018 10:44:58 +0000 (13:44 +0300)]
dpaa2-eth: Add ethtool support for flow classification
Add support for inserting and deleting Rx flow classification
rules through ethtool.
We support classification based on some header fields for
flow-types ether, ip4, tcp4, udp4 and sctp4.
Rx queues are core affine, so the action argument effectively
selects on which cpu the matching frame will be processed.
Discarding the frame is also supported.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Radulescu [Mon, 1 Oct 2018 10:44:57 +0000 (13:44 +0300)]
dpaa2-eth: Configure Rx flow classification key
For firmware versions that support it, configure an Rx flow
classification key at probe time.
Hardware expects all rules in the classification table to share
the same key. So we setup a key containing all supported fields
at driver init and when a user adds classification rules through
ethtool, we will just mask out the unused header fields.
Since the key composition process is the same for flow
classification and hashing, reuse existing code where possible.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Radulescu [Mon, 1 Oct 2018 10:44:56 +0000 (13:44 +0300)]
dpaa2-eth: Rename structure
Since the array of supported header fields will be used for
Rx flow classification as well, rename it from "hash_fields" to
the more inclusive "dist_fields".
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Radulescu [Mon, 1 Oct 2018 10:44:55 +0000 (13:44 +0300)]
dpaa2-eth: Use new API for Rx flow hashing
The Management Complex (MC) firmware initially allowed the
configuration of a single key to be used both for Rx flow hashing
and flow classification. This prevented us from supporting
Rx flow classification through ethtool.
Starting with version 10.7.0, the Management Complex(MC) offers
a new set of APIs for separate configuration of Rx hashing and
classification keys.
Update the Rx flow hashing support to use the new API, if available.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Dooks [Mon, 1 Oct 2018 16:02:43 +0000 (17:02 +0100)]
net: usbnet: make driver_info const
The driver_info field that is used for describing each of the usb-net
drivers using the usbnet.c core all declare their information as const
and the usbnet.c itself does not try and modify the struct.
It is therefore a good idea to make this const in the usbnet.c structure
in case anyone tries to modify it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 2 Oct 2018 06:24:26 +0000 (23:24 -0700)]
tcp: do not release socket ownership in tcp_close()
syzkaller was able to hit the WARN_ON(sock_owned_by_user(sk));
in tcp_close()
While a socket is being closed, it is very possible other
threads find it in rtnetlink dump.
tcp_get_info() will acquire the socket lock for a short amount
of time (slow = lock_sock_fast(sk)/unlock_sock_fast(sk, slow);),
enough to trigger the warning.
Fixes:
67db3e4bfbc9 ("tcp: no longer hold ehash lock while calling tcp_get_info()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski [Sun, 30 Sep 2018 06:44:54 +0000 (23:44 -0700)]
net: inet6_rtm_getroute() - use new style struct initializer instead of memset
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski [Sun, 30 Sep 2018 06:44:53 +0000 (23:44 -0700)]
net: rtm_to_fib6_config() - use new style struct initializer instead of memset
(allows for better compiler optimization)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski [Sun, 30 Sep 2018 06:44:52 +0000 (23:44 -0700)]
net: rtmsg_to_fib6_config() - use new style struct initializer instead of memset
(allows for better compiler optimization)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski [Sun, 30 Sep 2018 06:44:51 +0000 (23:44 -0700)]
net: ip6_update_pmtu() - use new style struct initializer instead of memset
(allows for better compiler optimization)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski [Sun, 30 Sep 2018 06:44:50 +0000 (23:44 -0700)]
net: remove 1 always zero parameter from ip6_redirect_no_header()
(the parameter in question is mark)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski [Sun, 30 Sep 2018 06:44:49 +0000 (23:44 -0700)]
net: ip6_redirect_no_header() - use new style struct initializer instead of memset
(allows for better compiler optimization)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski [Sun, 30 Sep 2018 06:44:48 +0000 (23:44 -0700)]
net: ip6_redirect() - use new style struct initializer instead of memset
(allows for better compiler optimization)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski [Sun, 30 Sep 2018 06:44:47 +0000 (23:44 -0700)]
net: inet_rtm_getroute() - use new style struct initializer instead of memset
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski [Sun, 30 Sep 2018 06:44:46 +0000 (23:44 -0700)]
net: ip_rt_get_source() - use new style struct initializer instead of memset
(allows for better compiler optimization)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Oct 2018 18:46:29 +0000 (11:46 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2018-10-02' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Oct 2018 18:39:09 +0000 (11:39 -0700)]
Merge branch '100GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-10-02
This series contains updates to ice driver only.
Anirudh expands the use of VSI handles across the rest of the driver,
which includes refactoring the code to correctly use VSI handles. After
a reset, ensure that all configurations for a VSI get re-applied before
moving on to rebuilding the next VSI.
Dave fixed the driver to check the current link state after reset to
ensure that the correct link state of a port is reported. Fixed an
issue where if the driver is unloaded when traffic is in progress,
errors are generated.
Preethi breaks up the IRQ tracker into a software and hardware IRQ
tracker, where the software IRQ tracker tracks only the PF's IRQ
requests and does not play any role in the VF initialization. The
hardware IRQ tracker represents the device's interrupt space and will be
looked up to see if the device has run our of interrupts when a
interrupt has to be allocated in the device for either PF or VF.
Md Fahad adds support for enabling/disabling RSS via ethtool.
Brett aligns the ice_reset_req enum values to the values that the
hardware understands. Also added initial support for dynamic interrupt
moderation in the ice driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Oct 2018 18:29:41 +0000 (11:29 -0700)]
Merge branch 'qed-20g'
Sudarsana Reddy Kalluru says:
====================
qed*: Driver support for 20G link speed.
The patch series adds driver support for configuring/reading the 20G link
speed.
Please consider applying this to "net-next".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Tue, 2 Oct 2018 13:16:12 +0000 (06:16 -0700)]
qede: Add driver support for 20G link speed.
Add driver support for reading/configuring the 20G link speed via ethtool.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Tue, 2 Oct 2018 13:16:11 +0000 (06:16 -0700)]
qed: Add driver support for 20G link speed.
Add driver support for configuring/reading the 20G link speed.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Tue, 2 Oct 2018 10:28:32 +0000 (12:28 +0200)]
isdn/hisax: Fix fall-through annotation
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 2 Oct 2018 09:03:40 +0000 (11:03 +0200)]
net: drop unused skb_append_datato_frags()
This helper is unused since commit
988cf74deb45 ("inet:
Stop generating UFO packets.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Ertman [Thu, 20 Sep 2018 00:43:07 +0000 (17:43 -0700)]
ice: Fix error on driver remove
If the driver is unloaded when traffic is in progress, errors are
generated. Fix this by releasing qvectors and NAPI handler on remove.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 20 Sep 2018 00:23:19 +0000 (17:23 -0700)]
ice: Add support for dynamic interrupt moderation
Currently there is no support for dynamic interrupt moderation. This
patch adds some initial code to support this. The following changes
were made:
1. Currently we are using multiple members to store the interrupt
granularity (itr_gran_25/50/100/200). This is not necessary because
we can query the device to determine what the interrupt granularity
should be set to, done by a new function ice_get_itr_intrl_gran.
2. Added intrl to ice_q_vector structure to support interrupt rate
limiting.
3. Added the function ice_intrl_usecs_to_reg for converting to a value
in usecs that the device understands.
4. Added call to write to the GLINT_RATE register. Disable intrl by
default for now.
5. Changed rx/tx_itr_setting to itr_setting because having both seems
redundant because a ring is either Tx or Rx.
6. Initialize itr_setting for both Tx/Rx rings in ice_vsi_alloc_rings()
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 20 Sep 2018 00:23:18 +0000 (17:23 -0700)]
ice: Align ice_reset_req enum values to hardware reset values
Currently the ice_reset_req enum values have to be translated into
a different set of values that the hardware understands for the same
reset types. Avoid this translation by aligning ice_reset_req enum
values to the ones that the hardware understands.
Also add and else if block to check for ICE_RESET_EMPR and put a dev_dbg
message in the else case.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Md Fahad Iqbal Polash [Thu, 20 Sep 2018 00:23:17 +0000 (17:23 -0700)]
ice: Implement ethtool hook for RSS switch
This patch implements ethtool hook for enabling/disabling
RSS. While disabling RSS, the LUT should be cleared. And
the LUT should be reconfigured while enabling RSS.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Preethi Banala [Thu, 20 Sep 2018 00:23:16 +0000 (17:23 -0700)]
ice: Split irq_tracker into sw_irq_tracker and hw_irq_tracker
For the PF driver, when mapping interrupts to queues, we need to request
IRQs from the kernel and we also have to allocate interrupts from
the device.
Similarly, when the VF driver (iavf.ko) initializes, it requests the kernel
IRQs that it needs but it can't directly allocate interrupts in the device.
Instead, it sends a mailbox message to the ice driver, which then allocates
interrupts in the device on the VF driver's behalf.
Currently both these cases end up having to reserve entries in
pf->irq_tracker but irq_tracker itself is sized based on how many vectors
the PF driver needs. Under the right circumstances, the VF driver can fail
to get entries in irq_tracker, which will result in the VF driver failing
probe.
To fix this, sw_irq_tracker and hw_irq_tracker are introduced. The
sw_irq_tracker tracks only the PF's IRQ request and doesn't play any
role in VF init. hw_irq_tracker represents the device's interrupt space.
When interrupts have to be allocated in the device for either PF or VF,
hw_irq_tracker will be looked up to see if the device has run out of
interrupts.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dave Ertman [Thu, 20 Sep 2018 00:23:15 +0000 (17:23 -0700)]
ice: Check for actual link state of port after reset
We are currently replaying the link state of a port after a reset, but
it is possible that the link state of a port can change during the reset
process. So check for the current link state of a port during the rebuild
process of a reset.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Anirudh Venkataramanan [Thu, 20 Sep 2018 00:23:14 +0000 (17:23 -0700)]
ice: Implement VSI replay framework
Currently, switch filters get replayed after reset. In addition to
filters, other VSI attributes (like RSS configuration, Tx scheduler
configuration, etc.) also need to be replayed after reset.
Thus, instead of replaying based on functional blocks (i.e. replay
all filters for all VSIs, followed by RSS configuration replay for
all VSIs, and so on), it makes more sense to have the replay centered
around a VSI. In other words, replay all configurations for a VSI before
moving on to rebuilding the next VSI.
To that effect, this patch introduces a VSI replay framework in a new
function ice_vsi_replay_all. Currently it only replays switch filters,
but it will be expanded in the future to replay additional VSI attributes.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Anirudh Venkataramanan [Thu, 20 Sep 2018 00:23:13 +0000 (17:23 -0700)]
ice: Expand use of VSI handles part 2/2
This patch is a continuation of the previous patch where VSI
handles are used instead of VSI numbers.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Anirudh Venkataramanan [Thu, 20 Sep 2018 00:23:12 +0000 (17:23 -0700)]
ice: Expand use of VSI handles part 1/2
A VSI handle is just a number the driver maintains to uniquely identify
a VSI. A VSI handle is backed by a VSI number in the hardware. When
interacting when the hardware, VSI handles are converted into VSI numbers.
In commit
0f9d5027a749 ("ice: Refactor VSI allocation, deletion and
rebuild flow"), VSI handles were introduced but it was used only
when creating and deleting VSIs. This patch is part one of two patches
that expands the use of VSI handles across the rest of the driver. Also
in this patch, certain parts of the code had to be refactored to correctly
use VSI handles.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Tue, 2 Oct 2018 06:31:16 +0000 (23:31 -0700)]
Merge branch 'ibmvnic-Implement-driver-defined-queue-limits'
Thomas Falcon says:
====================
ibmvnic: Implement driver-defined queue limits
In this patch series, update the ibmvnic driver to use driver-defined
queue limits instead of limits imposed by the Virtual I/O server
management partition. For some deviced, initial max queue size and
amount limits, despite their definition, can actually be exceeded if
the client driver requests it. With this in mind, define a private
ethtool flag that toggles the use of driver-defined limits. These
limits are currently more than what supported hardware will likely
allow, so the driver will attempt to get as close as possible to
the user request but may not fully succeed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 28 Sep 2018 23:38:26 +0000 (18:38 -0500)]
ibmvnic: Add ethtool private flag for driver-defined queue limits
When choosing channel amounts and ring sizes, the maximums in the
ibmvnic driver are defined by the virtual i/o server management
partition. Even though they are defined as maximums, the client
driver may in fact successfully request resources that exceed
these limits, which are mostly dependent on a user's hardware
With this in mind, provide an ethtool flag that when enabled will
allow the user to request resources limited by driver-defined
maximums instead of limits defined by the management partition.
The driver will try to honor the user's request but may not allowed
by the management partition. In this case, the driver requests
as close as it can get to the desired amount until it succeeds.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 28 Sep 2018 23:38:25 +0000 (18:38 -0500)]
ibmvnic: Introduce driver limits for ring sizes
Introduce driver-defined maximums for queue ring sizes. Devices
available for IBM vNIC today will likely not allow this amount,
but this should give us some leeway for future devices that may
support larger ring sizes.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 28 Sep 2018 23:38:24 +0000 (18:38 -0500)]
ibmvnic: Increase maximum queue size limit
Increase queue size limit to 16. Devices available for IBM vNIC today
will not allow this amount, but this should give us some leeway for
future devices that may support more RX or TX queues.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Herring [Fri, 28 Sep 2018 22:04:59 +0000 (17:04 -0500)]
net: phy: Convert to using %pOFn instead of device_node.name
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 28 Sep 2018 17:28:44 +0000 (10:28 -0700)]
tcp/fq: move back to CLOCK_MONOTONIC
In the recent TCP/EDT patch series, I switched TCP and sch_fq
clocks from MONOTONIC to TAI, in order to meet the choice done
earlier for sch_etf packet scheduler.
But sure enough, this broke some setups were the TAI clock
jumps forward (by almost 50 year...), as reported
by Leonard Crestez.
If we want to converge later, we'll probably need to add
an skb field to differentiate the clock bases, or a socket option.
In the meantime, an UDP application will need to use CLOCK_MONOTONIC
base for its SCM_TXTIME timestamps if using fq packet scheduler.
Fixes:
72b0094f9182 ("tcp: switch tcp_clock_ns() to CLOCK_TAI base")
Fixes:
142537e41923 ("net_sched: sch_fq: switch to CLOCK_TAI")
Fixes:
fd2bca2aa789 ("tcp: switch internal pacing timer to CLOCK_TAI")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vakul Garg [Fri, 28 Sep 2018 16:18:08 +0000 (21:48 +0530)]
selftests/tls: Fix recv(MSG_PEEK) & splice() test cases
TLS test cases splice_from_pipe, send_and_splice &
recv_peek_multiple_records expect to receive a given nummber of bytes
and then compare them against the number of bytes which were sent.
Therefore, system call recv() must not return before receiving the
requested number of bytes, otherwise the subsequent memcmp() fails.
This patch passes MSG_WAITALL flag to recv() so that it does not return
prematurely before requested number of bytes are copied to receive
buffer.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 28 Sep 2018 14:41:23 +0000 (14:41 +0000)]
hv_netvsc: Fix rndis_per_packet_info internal field initialization
The RSC feature -- a bit field "internal" was added here with total
size unchanged:
struct rndis_per_packet_info {
u32 size;
u32 type:31;
u32 internal:1;
u32 ppi_offset;
};
On TX path, we put rndis msg into skb head room, which is not zeroed
before passing to us. We do not use the "internal" field in TX path,
but it may impact older hosts which use the entire 32 bits as "type".
To fix the bug, this patch sets the field "internal" to zero.
Fixes:
c8e4eff4675f ("hv_netvsc: Add support for LRO/RSC in the vSwitch")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 28 Sep 2018 06:51:09 +0000 (08:51 +0200)]
net: phy: improve handling delayed work
Using mod_delayed_work() allows to simplify handling delayed work and
removes the need for the sync parameter in phy_trigger_machine().
Also introduce a helper phy_queue_state_machine() to encapsulate the
low-level delayed work calls. No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Oct 2018 06:11:53 +0000 (23:11 -0700)]
Merge branch 'net-systemport-Turn-on-offloads-by-default'
Florian Fainelli says:
====================
net: systemport: Turn on offloads by default
Up until now, we had added all the code necessary to turn on RX/TX
checksum offloads at runtime, but there is no reason why they have to be
disabled by default given that this gives a slight performance
improvement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 27 Sep 2018 22:36:14 +0000 (15:36 -0700)]
net: systemport: Add software counters to track reallocations
When inserting the TSB, keep track of how many times we had to do it and
if there was a failure in doing so, this helps profile the driver for
possibly incorrect headroom settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 27 Sep 2018 22:36:13 +0000 (15:36 -0700)]
net: systemport: Be drop monitor friendly while re-allocating headroom
During bcm_sysport_insert_tsb() make sure we differentiate a SKB
headroom re-allocation failure from the normal swap and replace path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 27 Sep 2018 22:36:12 +0000 (15:36 -0700)]
net: systemport: Turn on offloads by default
We can turn on the RX/TX checksum offloads by default and make sure that
those are properly reflected back to e.g: stacked devices such as VLAN
or DSA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 27 Sep 2018 22:36:11 +0000 (15:36 -0700)]
net: systemport: Utilize bcm_sysport_set_features() during resume/open
During driver resume and open, the HW may have lost its context/state,
utilize bcm_sysport_set_features() to make sure we do restore the
correct set of features that were previously configured.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 27 Sep 2018 22:36:10 +0000 (15:36 -0700)]
net: systemport: Refactor bcm_sysport_set_features()
In preparation for unconditionally enabling TX and RX checksum offloads,
refactor bcm_sysport_set_features() a bit such that
__netdev_update_features() during register_netdev() can make sure that
features are correctly programmed during network device registration.
Since we can now be called during register_netdev() with clocks gated,
we need to temporarily turn them on/off in order to have a successful
register programming.
We also move the CRC forward setting read into
bcm_sysport_set_features() since priv->crc_fwd matters while turning on
RX checksum offload, that way we are guaranteed they are in sync in case
we ever add support for NETIF_F_RXFCS at some point in the future.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 27 Sep 2018 20:42:19 +0000 (13:42 -0700)]
net_sched: fix a crash in tc_new_tfilter()
When tcf_block_find() fails, it already rollbacks the qdisc refcnt,
so its caller doesn't need to clean up this again. Avoid calling
qdisc_put() again by resetting qdisc to NULL for callers.
Reported-by: syzbot+37b8770e6d5a8220a039@syzkaller.appspotmail.com
Fixes:
e368fdb61d8e ("net: sched: use Qdisc rcu API instead of relying on rtnl lock")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Oct 2018 06:05:32 +0000 (23:05 -0700)]
Merge branch 'netlink-extended-attribute-validation'
Johannes Berg says:
====================
netlink: extended attribute validation
This adds further netlink attribute validation:
* min/max/range validation
* validation through a custom function pointer
This is useful to
* reduce boilerplate code in command handling code, if attributes
are used commonly across different commands
* get more extended ACK error messages/attribute pointers
* ensure attributes are valid even when ignored
(though this might be a problem when converting existing code)
Changes since v1:
* split off validate_type from type and use that for min/max/range
and function; this is better because the range is limited to the
range of s16 and so things like "u16 with minimum value 1" couldn't
be expressed earlier
* add macros for this, e.g. NLA_POLICY_MIN(NLA_U16, 1) for the case
mentioned in the previous bullet
Using this pretty much in all places where applicable in nl80211
reduces the code size there by about 1.8KiB, with just a minimal
code increase in lib/nlattr.o.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 27 Sep 2018 09:28:36 +0000 (11:28 +0200)]
netlink: add validation function to policy
Add the ability to have an arbitrary validation function attached
to a netlink policy that doesn't already use the validation_data
pointer in another way.
This can be useful to validate for example the content of a binary
attribute, like in nl80211 the "(information) elements", which must
be valid streams of "u8 type, u8 length, u8 value[length]".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 27 Sep 2018 09:28:35 +0000 (11:28 +0200)]
netlink: add attribute range validation to policy
Without further bloating the policy structs, we can overload
the `validation_data' pointer with a struct of s16 min, max
and use those to validate ranges in NLA_{U,S}{8,16,32,64}
attributes.
It may sound strange to validate NLA_U32 with a s16 max, but
in many cases NLA_U32 is used for enums etc. since there's no
size benefit in using a smaller attribute width anyway, due
to netlink attribute alignment; in cases like that it's still
useful, particularly when the attribute really transports an
enum value.
Doing so lets us remove quite a bit of validation code, if we
can be sure that these attributes aren't used by userspace in
places where they're ignored today.
To achieve all this, split the 'type' field and introduce a
new 'validation_type' field which indicates what further
validation (beyond the validation prescribed by the type of
the attribute) is done. This currently allows for no further
validation (the default), as well as min, max and range checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Oct 2018 05:57:46 +0000 (22:57 -0700)]
Merge branch 'Support-of-Flow-Director-in-HNS3-Ethernet-Driver-for-HiP08-Rev2-SoC'
Salil Mehta says:
====================
Support of Flow Director in HNS3 Ethernet Driver for HiP08 Rev2 SoC
This patch-set adds the support of FD(Flow Director) in the HNS3 PF driver
for HiP08 Rev2(0x21) SoC of Hisilicon. FD can be used in filtering the flows
and deciding to drop the flow or forward it to paricular queue.
Configuration consists of rules with input keys and actions. The rules are
stored in TCAM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 1 Oct 2018 11:46:47 +0000 (12:46 +0100)]
net: hns3: Add support for enable/disable flow director
This patch adds switch for flow director with ethtool command
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 1 Oct 2018 11:46:46 +0000 (12:46 +0100)]
net: hns3: Remove all flow director rules when unload hns3 driver
This patch removes all flow director rules when unload hns3 driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 1 Oct 2018 11:46:45 +0000 (12:46 +0100)]
net: hns3: Add reset handle for flow director
When doing reset, remove all entries in TCAM block, and keep flow
director rules list. After finishing reset, restore all entries.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 1 Oct 2018 11:46:44 +0000 (12:46 +0100)]
net: hns3: Add support for rule query of flow director
This patch adds support for querying rule number and rule details
by ethtool commands.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 1 Oct 2018 11:46:43 +0000 (12:46 +0100)]
net: hns3: Add support for rule add/delete for flow director
This patch adds support for add and delete rule by ethtool commands.
HNS3 driver supports several flow types, include ETHER_FLOW,
IP_USER_FLOW, TCP_V4_FLOW, UDP_V4_FLOW, SCTP_V4_FLOW, IPV6_USER_FLOW,
TCP_V6_FLOW, UDP_V6_FLOW and SCTP_V6_FLOW.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 1 Oct 2018 11:46:42 +0000 (12:46 +0100)]
net: hns3: Add input key and action config support for flow director
Each flow director rule consists of input key and action. The input key
is the condition for matching, includes tuples of L2/L3/L4 header.
Action is the behaviour when a packet matches with the input key, such
as drop the packet, or forward to a specified queue.
The input key is stored in the tcam blocks, Each bit of input key can
be masked.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Mon, 1 Oct 2018 11:46:41 +0000 (12:46 +0100)]
net: hns3: Add flow director initialization
Flow director is a new feature supported by hardware with revision 0x21.
This patch adds flow direcor initialization for each PF. It queries flow
director mode and tcam resource from firmware, selects tuples used for
input key.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Oct 2018 05:55:36 +0000 (22:55 -0700)]
Merge branch 'Continue-towards-using-linkmode-in-phylib'
Andrew Lunn says:
====================
Continue towards using linkmode in phylib
These patches contain some further cleanup and helpers, and the first
real patch towards using linkmode bitmaps in phylink.
The macro magic in the RFC version has been replaced with run time
initialisation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 29 Sep 2018 21:04:16 +0000 (23:04 +0200)]
net: phy: Replace phy driver features u32 with link_mode bitmap
This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.
Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.
Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 29 Sep 2018 21:04:15 +0000 (23:04 +0200)]
net: ethernet: xgbe: expand PHY_GBIT_FEAUTRES
The macro PHY_GBIT_FEAUTRES needs to change into a bitmap in order to
support link_modes. Remove its use from xgde by replacing it with its
definition.
Probably, the current behavior is wrong. It probably should be
ANDing not assigning.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 29 Sep 2018 21:04:14 +0000 (23:04 +0200)]
net: phy: Add limkmode equivalents to some of the MII ethtool helpers
Add helpers which take a linkmode rather than a u32 ethtool for
advertising settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 29 Sep 2018 21:04:13 +0000 (23:04 +0200)]
net: phy: Add helper for advertise to lcl value
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 29 Sep 2018 21:04:12 +0000 (23:04 +0200)]
net: phy: Add helper to convert MII ADV register to a linkmode
The phy_mii_ioctl can be used to write a value into the MII_ADVERTISE
register in the PHY. Since this changes the state of the PHY, we need
to make the same change to phydev->advertising. Add a helper which can
convert the register value to a linkmode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 29 Sep 2018 21:04:11 +0000 (23:04 +0200)]
net: phy: Add phydev_info()
Add phydev_info() and make use of it within the phy drivers and core
code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 29 Sep 2018 21:04:10 +0000 (23:04 +0200)]
net: phy: Add phydev_warn()
Not all new style LINK_MODE bits can be converted into old style
SUPPORTED bits. We need to warn when such a conversion is attempted.
Add a helper for this.
Convert all pr_warn() calls to phydev_warn() where possible.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 29 Sep 2018 21:04:09 +0000 (23:04 +0200)]
net: phy: Move linkmode helpers to somewhere public
phylink has some useful helpers to working with linkmode bitmaps.
Move them to there own header so other code can use them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 26 Sep 2018 22:35:31 +0000 (15:35 -0700)]
nfp: warn on experimental TLV types
Reserve two TLV types for feature development, and warn in the driver
if they ever leak into production.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moritz Fischer [Thu, 27 Sep 2018 19:48:51 +0000 (12:48 -0700)]
net: nixge: Address compiler warnings when building for i386
Address compiler warning reported by kbuild autobuilders
when building for i386 as a result of dma_addr_t size on
different architectures.
warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
Fixes:
7e8d5755be0e ("net: nixge: Add support for 64-bit platforms")
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soheil Hassas Yeganeh [Wed, 26 Sep 2018 20:57:04 +0000 (16:57 -0400)]
tcp: adjust rcv zerocopy hints based on frag sizes
When SKBs are coalesced, we can have SKBs with different
frag sizes. Some with PAGE_SIZE and some not with PAGE_SIZE.
Since recv_skip_hint is always set to the full SKB size,
it can overestimate the amount that should be read using
normal read for coalesced packets.
Change the recv_skip_hint so that it only includes the first
frags that are not of PAGE_SIZE.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soheil Hassas Yeganeh [Wed, 26 Sep 2018 20:57:03 +0000 (16:57 -0400)]
tcp: set recv_skip_hint when tcp_inq is less than PAGE_SIZE
When we have less than PAGE_SIZE of data on receive queue,
we set recv_skip_hint to 0. Instead, set it to the actual
number of bytes available.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Oct 2018 05:31:17 +0000 (22:31 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-10-01
1) Make xfrmi_get_link_net() static to silence a sparse warning.
From Wei Yongjun.
2) Remove a unused esph pointer definition in esp_input().
From Haishuang Yan.
3) Allow the NIC driver to quietly refuse xfrm offload
in case it does not support it, the SA is created
without offload in this case.
From Shannon Nelson.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Sat, 22 Sep 2018 16:49:05 +0000 (18:49 +0200)]
ath9k: add back support for using active monitor interfaces for tx99
Various documented examples on how to set up tx99 with ath9k rely
on setting up a regular monitor interface for setting the channel.
My previous patch "ath9k: fix tx99 with monitor mode interface" made
it possible to set it up this way again. However, it was removing support
for using an active monitor interface, which is required for controlling
the bitrate as well, since the bitrate is not passed down with a regular
monitor interface.
This patch partially reverts the previous one, but keeps support for using
a regular monitor interface to keep documented steps working in cases
where the bitrate does not matter
Fixes:
d9c52fd17cb48 ("ath9k: fix tx99 with monitor mode interface")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Fri, 21 Sep 2018 20:42:41 +0000 (13:42 -0700)]
ath10k: add missing sanity check on diag download
ath10k_hw_diag_fast_download() generally has good boundary checking, but
it misses verifying that the next metadata header actually fits in the
remaining buffer space. Add such a check.
Fixes:
39501ea64116 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simon Wunderlich [Mon, 1 Oct 2018 14:26:59 +0000 (17:26 +0300)]
ath9k: fix reporting calculated new FFT upper max
Since the debug print code is outside of the loop, it shouldn't use the loop
iterator anymore but instead print the found maximum index.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simon Wunderlich [Mon, 1 Oct 2018 14:26:56 +0000 (17:26 +0300)]
ath9k: FFT magnitude check: don't consider lower 3 data bits
There were a lot of Magnitude Mismatch while getting FFT samples on my
hardware (Atheros AR9462. I've compared the reported magnitude with
the data in the FFT bin, and the FFT bin was less accurate:
[ 5395.193030] ath: phy0: FFT HT20 frame: max mag 0x89,max_mag_idx 28,
,magnitude 0x89 max_exp 0, data[28] = 0x88
[ 5395.194525] ath: phy0: FFT HT20 frame: max mag 0x89,max_mag_idx 28,
,magnitude 0x89 max_exp 0, data[28] = 0x88
[ 5395.196012] ath: phy0: FFT HT20 frame: max mag 0x88,max_mag_idx 28,
,magnitude 0x88 max_exp 0, data[28] = 0x88
[ 5395.197509] ath: phy0: FFT HT20 frame: max mag 0x6C,max_mag_idx 28,
,magnitude 0x6C max_exp 0, data[28] = 0x68
[ 5395.199015] ath: phy0: FFT HT20 frame: max mag 0x78,max_mag_idx 28,
,magnitude 0x78 max_exp 0, data[28] = 0x78
[ 5395.200497] ath: phy0: FFT HT20 frame: max mag 0xA1,max_mag_idx 28,
,magnitude 0xA1 max_exp 0, data[28] = 0xA0
[ 5395.202011] ath: phy0: FFT HT20 frame: max mag 0x91,max_mag_idx 28,
,magnitude 0x91 max_exp 0, data[28] = 0x90
[ 5395.203482] ath: phy0: FFT HT20 frame: max mag 0x89,max_mag_idx 28,
,magnitude 0x89 max_exp 0, data[28] = 0x88
[ 5395.204999] ath: phy0: FFT HT20 frame: max mag 0x27,max_mag_idx 4,
,magnitude 0x27 max_exp 0, data[4] = 0x20
[ 5395.206461] ath: phy0: FFT HT20 frame: max mag 0x41,max_mag_idx 28,
,magnitude 0x41 max_exp 0, data[28] = 0x40
[ 5395.207977] ath: phy0: FFT HT20 frame: max mag 0x51,max_mag_idx 28,
,magnitude 0x51 max_exp 0, data[28] = 0x50
[ 5395.209454] ath: phy0: FFT HT20 frame: max mag 0x53,max_mag_idx 28,
,magnitude 0x53 max_exp 0, data[28] = 0x50
[ 5395.210940] ath: phy0: FFT HT20 frame: max mag 0x40,max_mag_idx 28,
,magnitude 0x40 max_exp 0, data[28] = 0x40
[ 5395.212441] ath: phy0: FFT HT20 frame: max mag 0x59,max_mag_idx 28,
,magnitude 0x59 max_exp 0, data[28] = 0x58
[ 5395.213932] ath: phy0: FFT HT20 frame: max mag 0x53,max_mag_idx 28,
,magnitude 0x53 max_exp 0, data[28] = 0x50
[ 5395.215428] ath: phy0: FFT HT20 frame: max mag 0x7D,max_mag_idx 28,
,magnitude 0x7D max_exp 0, data[28] = 0x78
[ 5395.216910] ath: phy0: FFT HT20 frame: max mag 0x8C,max_mag_idx 28,
,magnitude 0x8C max_exp 0, data[28] = 0x88
[ 5395.218413] ath: phy0: FFT HT20 frame: max mag 0x7B,max_mag_idx 28,
,magnitude 0x7B max_exp 0, data[28] = 0x78
[ 5395.219900] ath: phy0: FFT HT20 frame: max mag 0x43,max_mag_idx 28,
,magnitude 0x43 max_exp 0, data[28] = 0x40
It seems like the lower 3 bits on my hardware are always zeroed, but the
magnitude matches otherwise. Therefore, let's not make the magnitude
check so strict so we can get those samples released to userspace.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simon Wunderlich [Mon, 1 Oct 2018 14:26:51 +0000 (17:26 +0300)]
ath9k: fix and simplify FFT max index retrieval
FFT max index retrieval was not retrieved correctly for HT20/HT40 FFT
frames. Fixing the retrieval allows us to remove the fixup function as
well. While at it, split the spectral_max_index function into versions
for ht20 and ht40 to simplify the code.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simon Wunderlich [Mon, 1 Oct 2018 14:26:46 +0000 (17:26 +0300)]
ath9k: return when short FFT frame was handled
With the loop break like this, there are false "FFT report truncated"
messages because the iterator is not advanced as the check expects.
Instead, just return, for a single frame there is nothing left to be
done anyways.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simon Wunderlich [Mon, 1 Oct 2018 14:26:42 +0000 (17:26 +0300)]
ath9k: add counters for good and errorneous FFT/spectral frames
This is helpful to see whether spectral samples get discarded.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>