OSDN Git Service
Julian Wiedmann [Mon, 26 Jul 2021 06:27:58 +0000 (08:27 +0200)]
s390/qdio: remove unused support for SLIB parameters
Neither of the two drivers provides any SLIB parameter data, so get rid
of the dead code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Julian Wiedmann [Mon, 26 Jul 2021 06:25:41 +0000 (08:25 +0200)]
s390/qdio: consolidate QIB code
Move all QIB-related code into qdio_setup_qib(), and slightly re-order
it according to the order of the struct's fields. This makes it easier
to understand what the QIB actually looks like before we send it to HW.
Also get rid of the qebsm_possible() helper - as 31-bit support is long
gone, the comment doesn't make any sense. And while removing some stale
QIB-related comment, also move the clearing of the QDR into its proper
place.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Julian Wiedmann [Mon, 12 Jul 2021 07:39:57 +0000 (09:39 +0200)]
s390/qdio: use dev_info() in qdio_print_subchannel_info()
Prefer dev_info() over a raw printk. This also adds the device and
driver names into the output, so that we have:
Before:
qdio: 0.0.17c0 ZFCP on SC 17 using [...]
After:
zfcp 0.0.17c0: qdio: ZFCP on SC 17 using [...]
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Julian Wiedmann [Fri, 23 Jul 2021 08:02:17 +0000 (10:02 +0200)]
s390/qdio: fine-tune the queue sync
Push the sync check from qdio_inspect_queue() down into the two
get_*_buffer_frontier() code paths, where we actually need the sync to
look at the current queue state. This lets us avoid the check when we
know that there is no work on the queue (ie. when q->nr_buf_used is 0).
While at it introduce the qdio_sync_*_queue() helpers, so that we can
avoid the branch on q->is_input_q when we already know the queue type.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Julian Wiedmann [Fri, 23 Jul 2021 06:06:50 +0000 (08:06 +0200)]
s390/qdio: clean up SIGA capability tracking
Don't bother with translating the SIGA-related capability bits into
our own internal format, just cache the full qdioac1 field instead.
Also adjust the helper macros so that they take a qdio_irq argument
and can be used everywhere, instead of taking a qdio_q and then
internally dereferencing the parent pointer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Julian Wiedmann [Tue, 23 Mar 2021 22:43:02 +0000 (23:43 +0100)]
s390/qdio: remove unused sync-after-IRQ infrastructure
The queue processing is fully decoupled from any preceding interrupt,
so we're no longer making any use of the sync-after-IRQ HW capabilities.
And as SIGA-sync is a legacy feature, there's also not much point in
re-designing the driver & qdio-layer code just so that we can
potentially avoid a few syncs. So just remove all the leftover code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Julian Wiedmann [Thu, 8 Jul 2021 06:32:46 +0000 (08:32 +0200)]
s390/qdio: use absolute data address in ESTABLISH ccw
Clean up yet another path where HW wants an absolute address, and we've
been implicitly relying on V=R.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Vineeth Vijayan [Sun, 25 Apr 2021 08:52:38 +0000 (10:52 +0200)]
s390/cio: add dev_busid sysfs entry for each subchannel
Introduce dev_busid, which exports the device-id associated with the
io-subchannel (and message-subchannel). The dev_busid indicates that of
the device which may be physically installed on the corrosponding
subchannel. The dev_busid value "none" indicates that the subchannel
is not valid, there is no I/O device currently associated with the
subchannel.
The dev_busid information would be helpful to write device-specific
udev-rules associated with the subchannel. The dev_busid interface would
be available even when the sch is not bound to any driver or if there is
no operational device connected on it. Hence this attribute can be used to
write udev-rules which are specific to the device associated with the
subchannel.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Vineeth Vijayan [Sun, 25 Apr 2021 09:27:59 +0000 (11:27 +0200)]
s390/cio: add rescan functionality on channel subsystem
This patch introduces a new rescan sys-interface for channel-subsystem.
The rescan interface allows the user to invoke an evaluation of all
subchannels defined in the I/O configuration.
The new rescan interface can be found at /sys/devices/css0/rescan
and can be triggered by,
echo > /sys/devices/css0/rescan
Writing to this interface triggers subchannel evaluation. The write
request completes only after scan-related work has completed
This user-invoked subchannel evaluation allows manual recovery in error
situations such as:
- restart of device discovery after resolution of temporary device
error
- inconsistent OS view of subchannel state due to missing state-change
interrupts (CRWs)
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Heiko Carstens [Wed, 4 Aug 2021 11:40:31 +0000 (13:40 +0200)]
s390: rename dma section to amode31
The dma section name is confusing, since the code which resides within
that section has nothing to do with direct memory access. Instead the
limitation is that the code has to run in 31 bit addressing mode, and
therefore has to reside below 2GB. So the name was chosen since
ZONE_DMA is the same region.
To reduce confusion rename the section to amode31, which hopefully
describes better what this is about.
Note: this will also change vmcoreinfo strings
- SDMA=... gets renamed to SAMODE31=...
- EDMA=... gets renamed to EAMODE31=...
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Tue, 3 Aug 2021 12:42:29 +0000 (14:42 +0200)]
s390/mm: use page_to_virt() in __kernel_map_pages()
Fix virtual vs physical address confusion (which currently are the same).
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Sebastian Andrzej Siewior [Tue, 3 Aug 2021 14:15:48 +0000 (16:15 +0200)]
s390/sclp: replace deprecated CPU-hotplug functions
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-6-bigeasy@linutronix.de
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Sebastian Andrzej Siewior [Tue, 3 Aug 2021 14:15:47 +0000 (16:15 +0200)]
s390: replace deprecated CPU-hotplug functions
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-5-bigeasy@linutronix.de
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Ilya Leoshkevich [Wed, 28 Jul 2021 21:25:46 +0000 (23:25 +0200)]
s390/ftrace: implement hotpatching
s390 allows hotpatching the mask of a conditional jump instruction.
Make use of this feature in order to avoid the expensive stop_machine()
call.
The new trampolines are split in 3 stages:
- A first stage is a 6-byte relative conditional long branch located at
each function's entry point. Its offset always points to the second
stage for the corresponding function, and its mask is either all 0s
(ftrace off) or all 1s (ftrace on). The code for flipping the mask is
borrowed from ftrace_{enable,disable}_ftrace_graph_caller. After
flipping, ftrace_arch_code_modify_post_process() syncs with all the
other CPUs by sending SIGPs.
- Second stages for vmlinux are stored in a separate part of the .text
section reserved by the linker script, and in dynamically allocated
memory for modules. This prevents the icache pollution. The total
size of second stages is about 1.5% of that of the kernel image.
Putting second stages in the .bss section is possible and decreases
the size of the non-compressed vmlinux, but splits the kernel 1:1
mapping, which is a bad tradeoff.
Each second stage contains a call to the third stage, a pointer to
the part of the intercepted function right after the first stage, and
a pointer to an interceptor function (e.g. ftrace_caller).
Second stages are 8-byte aligned for the future direct calls
implementation.
- There are only two copies of the third stage: in the .text section
for vmlinux and in dynamically allocated memory for modules. It can be
an expoline, which is relatively large, so inlining it into each
second stage is prohibitively expensive.
As a result of this organization, phoronix-test-suite with ftrace off
does not show any performance degradation.
Suggested-by: Sven Schnelle <svens@linux.ibm.com>
Suggested-by: Vasily Gorbik <gor@linux.ibm.com>
Co-developed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Link: https://lore.kernel.org/r/20210728212546.128248-3-iii@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Ilya Leoshkevich [Wed, 28 Jul 2021 21:25:45 +0000 (23:25 +0200)]
ftrace: Introduce ftrace_need_init_nop()
Implementing live patching on s390 requires each function's prologue to
contain a very special kind of nop, which gcc and clang don't generate.
However, the current code assumes that if CC_USING_NOP_MCOUNT is
defined, then whatever the compiler generates is good enough.
Move the CC_USING_NOP_MCOUNT check into the new ftrace_need_init_nop()
macro, that the architectures can override.
An alternative solution is to disable using -mnop-mcount in the
Makefile, however, this makes the build logic (even) more complicated
and forces the arch-specific code to deal with the useless __fentry__
symbol.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20210728212546.128248-2-iii@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Masahiro Yamada [Thu, 29 Jul 2021 14:23:38 +0000 (23:23 +0900)]
s390: move the install rule to arch/s390/Makefile
Currently, the install target in arch/s390/Makefile descends into
arch/s390/boot/Makefile to invoke the shell script, but there is no
good reason to do so.
arch/s390/Makefile can run the shell script directly.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210729142338.446002-1-masahiroy@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Ilya Leoshkevich [Wed, 28 Jul 2021 11:59:04 +0000 (13:59 +0200)]
s390: enable KCSAN
s390x GCC and SystemZ Clang have ThreadSanitizer support now [1] [2],
so enable KCSAN for s390.
[1] https://gcc.gnu.org/git/?p=gcc.git;a=commit;h=
ea22954e7c58
[2] https://reviews.llvm.org/
D105629
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Thu, 29 Jul 2021 14:28:11 +0000 (16:28 +0200)]
kcsan: use u64 instead of cycles_t
cycles_t has a different type across architectures: unsigned int,
unsinged long, or unsigned long long. Depending on architecture this
will generate this warning:
kernel/kcsan/debugfs.c: In function ‘microbenchmark’:
./include/linux/kern_levels.h:5:25: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘cycles_t’ {aka ‘long unsigned int’} [-Wformat=]
To avoid this simply change the type of cycle to u64 in microbenchmark(),
since u64 is of type unsigned long long for all architectures.
Acked-by: Marco Elver <elver@google.com>
Link: https://lore.kernel.org/r/20210729142811.1309391-1-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Sven Schnelle [Wed, 28 Jul 2021 19:02:54 +0000 (21:02 +0200)]
s390: add kfence region to pagetable dumper
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Link: https://lore.kernel.org/r/20210728190254.3921642-5-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Sven Schnelle [Wed, 28 Jul 2021 19:02:53 +0000 (21:02 +0200)]
s390: add support for KFENCE
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
[hca@linux.ibm.com: simplify/rework code]
Link: https://lore.kernel.org/r/20210728190254.3921642-4-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Sven Schnelle [Wed, 28 Jul 2021 19:02:52 +0000 (21:02 +0200)]
kfence: add function to mask address bits
s390 only reports the page address during a translation fault.
To make the kfence unit tests pass, add a function that might
be implemented by architectures to mask out address bits.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Marco Elver <elver@google.com>
Link: https://lore.kernel.org/r/20210728190254.3921642-3-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 28 Jul 2021 19:02:51 +0000 (21:02 +0200)]
s390/mm: implement set_memory_4k()
Implement set_memory_4k() which will split any present large or huge
mapping in the given range to a 4k mapping.
Link: https://lore.kernel.org/r/20210728190254.3921642-2-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Marco Elver [Wed, 28 Jul 2021 19:57:41 +0000 (21:57 +0200)]
kfence, x86: only define helpers if !MODULE
x86's <asm/tlbflush.h> only declares non-module accessible functions
(such as flush_tlb_one_kernel) if !MODULE.
In preparation of including <asm/kfence.h> from the KFENCE test module,
only define the helpers if !MODULE to avoid breaking the build with
CONFIG_KFENCE_KUNIT_TEST=m.
Signed-off-by: Marco Elver <elver@google.com>
Link: https://lore.kernel.org/r/YQJdarx6XSUQ1tFZ@elver.google.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Sun, 25 Jul 2021 13:13:12 +0000 (15:13 +0200)]
s390/delay: get rid of not needed header includes
After all the changes to delay.c there are many includes which are not
needed anymore. Get rid of them.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Sun, 25 Jul 2021 13:07:25 +0000 (15:07 +0200)]
s390/boot: get rid of arithmetics on function pointers
sparse warning:
CHECK arch/s390/boot/startup.c
arch/s390/boot/startup.c:283:39: error: arithmetics on pointers to functions
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Ilya Leoshkevich [Thu, 15 Jul 2021 11:51:02 +0000 (13:51 +0200)]
s390/headers: fix code style in module.h
struct brace should be on the same line.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 12:03:33 +0000 (14:03 +0200)]
s390/hwcaps: make sie capability regular hwcap
Commit
7f16d7e787b7 ("s390: show virtualization support in /proc/cpuinfo")
introduced special handling for sie capability, saying this should not be
exposed via hwcaps, without giving a reason.
However this leads to an inconsistent /proc/cpuinfo features line
where all features except the sie capability are also present in
hwcaps. I really don't see a reason to not add that to hwcaps - it
might be quite pointless, but at least this way it is possible to get
rid of some special handling.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 19:05:35 +0000 (21:05 +0200)]
s390/hwcaps: remove hwcap stfle check
Remove the not so obvious "(elf_hwcap & (1UL << 2)" which only checks
if stfle is available. This used to be required for old code before
test_facility() was introduced. test_facility() will do the right
thing, regardless if stfle is available or not.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 19:03:44 +0000 (21:03 +0200)]
s390/hwcaps: remove z/Architecture mode active check
Remove a leftover from the common 31/64 bit code. z/Architecture mode
is now always active, there is no need to check.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 19:03:04 +0000 (21:03 +0200)]
s390/hwcaps: use consistent coding style / remove comments
Use a consistent coding style within setup_hwcaps() and remove obvious
and outdated comments.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 18:58:03 +0000 (20:58 +0200)]
s390/hwcaps: open code initialization of first six hwcap bits
The first six hwcap bits are initialized in a rather odd way: an array
contains the stfl(e) bits which need to be set, so that the
corresponding bit position (= array index) within hwcaps are set.
Better open code it like it is done for all other bits, making it
obvious which bit is set when.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 11:25:21 +0000 (13:25 +0200)]
s390/hwcaps: split setup_hwcaps()
setup_hwcaps() is a quite large function. Make it smaller by moving
the elf platform setup code into an independent setup function.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 11:23:07 +0000 (13:23 +0200)]
s390/hwcaps: move setup_hwcaps()
Move setup_hwcaps() to processor.c for two reasons:
- make setup.c a bit smaller
- have allmost all of the hwcap code in one file
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 09:39:25 +0000 (11:39 +0200)]
s390/hwcaps: add sanity checks
Add BUILD_BUG_ON() sanity checks to make sure the hwcap string array
contains a string for each hwcap.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 09:35:19 +0000 (11:35 +0200)]
s390/hwcaps: use named initializers for hwcap string arrays
Use named initializers to make it obvious which hwcap string array
element belongs to which hwcap.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 09:12:36 +0000 (11:12 +0200)]
s390/hwcaps: introduce HWCAP bit numbers
Introduce HWCAP bit numbers, making it easier to tell at which bit
number we currently are. Also use these bits with the BIT macro to
define the real HWCAP masks.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 21 Jul 2021 08:56:57 +0000 (10:56 +0200)]
s390/hwcaps: shorten HWCAP defines
Remove s390 part of all HWCAP defines, just to make them shorter and
easier to handle. The namespace is anyway per architecture.
This is similar to what arm64 has.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Niklas Schnelle [Thu, 8 Jul 2021 13:43:13 +0000 (15:43 +0200)]
s390: add HWCAP_S390_PCI_MIO to ELF hwcaps
In order to support the use of enhanced PCI instructions in both kernel-
and userspace we need both hardware support and proper setup in the
kernel. The latter can be toggled off with the pci=nomio command line
option.
Thus availability of this feature in userspace depends on all of kernel
configuration (CONFIG_PCI), hardware support and the current kernel
command line and can thus not rely solely on a facility bit. Instead
let's introduce a new ELF hardware capability bit HWCAP_S390_PCI_MIO to
tell userspace whether these PCI instructions can be used.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Niklas Schnelle [Thu, 8 Jul 2021 12:55:42 +0000 (14:55 +0200)]
s390: make PCI mio support a machine flag
Kernel support for the newer PCI mio instructions can be toggled off
with the pci=nomio command line option which needs to integrate with
common code PCI option parsing. However this option then toggles static
branches which can't be toggled yet in an early_param() call.
Thus commit
9964f396f1d0 ("s390: fix setting of mio addressing control")
moved toggling the static branches to the PCI init routine.
With this setup however we can't check for mio support outside the PCI
code during early boot, i.e. before switching the static branches, which
we need to be able to export this as an ELF HWCAP.
Improve on this by turning mio availability into a machine flag that
gets initially set based on CONFIG_PCI and the facility bit and gets
toggled off if pci=nomio is found during PCI option parsing allowing
simple access to this machine flag after early init.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Mon, 15 Feb 2021 19:57:53 +0000 (20:57 +0100)]
s390/disassembler: add instructions
Add more instructions to the kernel disassembler.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Wed, 13 Jan 2021 13:14:01 +0000 (14:14 +0100)]
s390: report more CPU capabilities
Add hardware capability bits and feature tags to /proc/cpuinfo
for NNPA and Vector-Packed-Decimal-Enhancement Facility 2.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Julian Wiedmann [Mon, 22 Feb 2021 09:18:33 +0000 (10:18 +0100)]
s390/qdio: remove unused macros
These macros haven't seen any use in a long time. Also note that the
queue_irqs_*() ones wouldn't even compile anymore.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Julian Wiedmann [Wed, 14 Jul 2021 16:03:51 +0000 (18:03 +0200)]
s390/qdio: clarify reporting of errors to the drivers
Now that all drivers use qdio_inspect_queue() and qdio's internal
queue tasklets are gone, the driver-specified queue handlers are
only called for async error reporting (eg. for an error condition in
the QEBSM code).
So take a moment to clean up the Output Queue handlers (they are
_always_ called with qdio_error != 0), and clarify which error types
can be reported through what interface. As Benjamin already suggested
a while ago, we should turn these into distinct enums at some point.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Julian Wiedmann [Mon, 12 Jul 2021 06:29:32 +0000 (08:29 +0200)]
s390/qdio: remove unneeded siga-sync for Output Queue
get_outbound_buffer_frontier() is only reached via qdio_inspect_queue(),
and there we already call qdio_siga_sync_q() unconditionally.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Julian Wiedmann [Mon, 15 Mar 2021 18:39:20 +0000 (19:39 +0100)]
s390/qdio: remove remaining tasklet & timer code
Both qdio drivers have moved away from using qdio's internal tasklet
and timer mechanisms for Output Queues. Rip out all the leftovers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Julian Wiedmann [Tue, 1 Jun 2021 06:20:09 +0000 (08:20 +0200)]
s390/qdio: propagate error when cancelling a ccw fails
If qdio_cancel_ccw() times out (or is interrupted) before the interrupt
for the {halt,clear} action arrives, report this back to the caller as
an error.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Julian Wiedmann [Mon, 31 May 2021 15:38:04 +0000 (18:38 +0300)]
s390/qdio: improve roll-back after error on ESTABLISH ccw
If the ESTABLISH ccw fails (ie. the qdio_irq is set to
QDIO_IRQ_STATE_ERR), we don't need to call qdio_shutdown() for rolling
back our earlier actions. All the needed logic is already available in
qdio_establish()'s error chain, and using it means we don't have to
temporarily drop the setup_mutex either.
This makes qdio_shutdown() a purely external function, that should only
be called by the driver if an earlier qdio_establish() succeeded.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Julian Wiedmann [Mon, 31 May 2021 15:33:02 +0000 (18:33 +0300)]
s390/qdio: cancel the ESTABLISH ccw after timeout
When the ESTABLISH ccw does not complete within the specified timeout,
try our best to cancel the ccw program that is still active on the
device. Otherwise the IO subsystem might be accessing it even after
the driver eg. called qdio_free().
Fixes:
779e6e1c724d ("[S390] qdio: new qdio driver.")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Julian Wiedmann [Mon, 31 May 2021 15:40:06 +0000 (18:40 +0300)]
s390/qdio: fix roll-back after timeout on ESTABLISH ccw
When qdio_establish() times out while waiting for the ESTABLISH ccw to
complete, it calls qdio_shutdown() to roll back all of its previous
actions. But at this point the qdio_irq's state is still
QDIO_IRQ_STATE_INACTIVE, so qdio_shutdown() will exit immediately
without doing any actual work.
Which means that eg. the qdio_irq's thinint-indicator stays registered,
and cdev->handler isn't restored to its old value. And since
commit
954d6235be41 ("s390/qdio: make thinint registration symmetric")
the qdio_irq also stays on the tiq_list, so on the next qdio_establish()
we might get a helpful BUG from the list-debugging code:
...
[ 4633.512591] list_add double add: new=
00000000005a4110, prev=
00000001b357db78, next=
00000000005a4110.
[ 4633.512621] ------------[ cut here ]------------
[ 4633.512623] kernel BUG at lib/list_debug.c:29!
...
[ 4633.512796] [<
00000001b2c6ee9a>] __list_add_valid+0x82/0xa0
[ 4633.512798] ([<
00000001b2c6ee96>] __list_add_valid+0x7e/0xa0)
[ 4633.512800] [<
00000001b2fcecce>] qdio_establish_thinint+0x116/0x190
[ 4633.512805] [<
00000001b2fcbe58>] qdio_establish+0x128/0x498
...
Fix this by extracting a goto-chain from the existing error exits in
qdio_establish(), and check the return value of the wait_event_...()
to detect the timeout condition.
Fixes:
779e6e1c724d ("[S390] qdio: new qdio driver.")
Root-caused-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Wed, 16 Jun 2021 12:10:03 +0000 (14:10 +0200)]
s390/setup: don't reserve memory that occupied decompressor's head
There is no useful information within [STARTUP_NORMAL_OFFSET, HEAD_END] now.
But the memory region [0, STARTUP_NORMAL_OFFSET] is used by:
* lowcore
* kdump for swapping memory
* stand-alone zipl dumpers for code, data, stack and heap
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Tue, 15 Jun 2021 17:17:36 +0000 (19:17 +0200)]
s390/boot: move dma sections from decompressor to decompressed kernel
This change simplifies the task of making the decompressor relocatable.
The decompressor's image contains special DMA sections between _sdma and
_edma. This DMA segment is loaded at boot as part of the decompressor and
then simply handed over to the decompressed kernel. The decompressor itself
never uses it in any way. The primary reason for this is the need to keep
the aforementioned DMA segment below 2GB which is required by architecture,
and because the decompressor is always loaded at a fixed low physical
address, it is guaranteed that the DMA region will not cross the 2GB
memory limit. If the DMA region had been placed in the decompressed kernel,
then KASLR would make this guarantee impossible to fulfill or it would
be restricted to the first 2GB of memory address space.
This commit moves all DMA sections between _sdma and _edma from
the decompressor's image to the decompressed kernel's image. The complete
DMA region is placed in the init section of the decompressed kernel and
immediately relocated below 2GB at start-up before it is needed by other
parts of the decompressed kernel. The relocation of the DMA region happens
even if the decompressed kernel is already located below 2GB in order
to keep the first implementation simple. The relocation should not have
any noticeable impact on boot time because the DMA segment is only a couple
of pages.
After relocating the DMA sections, the kernel has to fix all references
which point into it. In order to automate this, place all variables
pointing into the DMA sections in a special .dma.refs section. All such
variables must be defined using the new __dma_ref macro. Only variables
containing addresses within the DMA sections must be placed in the new
.dma.refs section.
Furthermore, move the initialization of control registers from
the decompressor to the decompressed kernel because some control registers
reference tables that must be placed in the DMA data section to
guarantee that their addresses are below 2G. Because the decompressed
kernel relocates the DMA sections at startup, the content of control
registers CR2, CR5 and CR15 must be updated with new addresses after
the relocation. The decompressed kernel initializes all control registers
early at boot and then updates the content of CR2, CR5 and CR15
as soon as the DMA relocation has occurred. This practically reverts
the commit
a80313ff91ab ("s390/kernel: introduce .dma sections").
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Sun, 25 Jul 2021 12:12:58 +0000 (14:12 +0200)]
s390/ctl_reg: add ctlreg5 and ctlreg15 unions
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Tue, 15 Jun 2021 14:05:09 +0000 (16:05 +0200)]
s390/boot: make _diag308_reset_dma() position-independent
As a preparation for moving the .dma.data section from the decompressor to
the decompressed kernel, the .dma.data section must be made relocatable
by replacing absolute memory addressing with relative one. This is required
in order to be able to relocate the DMA section to a memory address <= 2G
as required by the hardware architecture. The DMA section must be
relocated in case the decompressed kernel was loaded to an address >= 2G
which can occur if KASAN is enabled. By making the whole DMA section
position-independent we avoid applying relocations to it whenever it is
moved to a different address, which becomes possible as soon as it becomes
a part of the decompressed kernel.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Wed, 21 Jul 2021 14:47:20 +0000 (16:47 +0200)]
s390/boot: move EP_OFFSET and EP_STRING to head.S
Both macros are used only in decompressor's head.S, unnecessary to put
them in a global header used in many places like setup.h is.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Wed, 21 Jul 2021 10:27:59 +0000 (12:27 +0200)]
s390/setup: generate asm offsets from struct parmarea
To reduce duplication, replace error-prone and hard-coded parameter area
offsets with auto-generated ones.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Wed, 21 Jul 2021 09:54:33 +0000 (11:54 +0200)]
s390/setup: drop _OFFSET macros
The macros
* IPL_DEVICE_OFFSET
* INITRD_START_OFFSET
* INITRD_SIZE_OFFSET
* OLDMEM_BASE_OFFSET
* OLDMEM_SIZE_OFFSET
* KERNEL_VERSION_OFFSET
* COMMAND_LINE_OFFSET
are no longer necessary and used only to define another set of macros
with the same names but w/o the suffix _OFFSET. Therefore, drop this
unnecessary indirection.
Drop the macro KERNEL_VERSION_OFFSET w/o renaming it to KERNEL_VERSION
because it is used nowhere.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Tue, 15 Jun 2021 10:57:31 +0000 (12:57 +0200)]
s390/setup: remove unused symbolic constants for C code from setup.h
These symbolic constants are used only by assembler code now:
* COMMAND_LINE
* IPL_DEVICE
C code of the decompressed kernel should use boot data passed
by the decompressor instead.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Tue, 15 Jun 2021 12:25:41 +0000 (14:25 +0200)]
s390/dump: introduce boot data 'oldmem_data'
The new boot data struct shall replace global variables OLDMEM_BASE and
OLDMEM_SIZE. It is initialized in the decompressor and passed
to the decompressed kernel. In comparison to the old solution, this one
doesn't access data at fixed physical addresses which will become important
when the decompressor becomes relocatable.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Tue, 15 Jun 2021 12:15:07 +0000 (14:15 +0200)]
s390/boot: introduce boot data 'initrd_data'
The new boot data struct shall replace global variables INITRD_START and
INITRD_SIZE. It is initialized in the decompressor and passed
to the decompressed kernel. In comparison to the old solution, this one
doesn't access data at fixed physical addresses which will become important
when the decompressor becomes relocatable.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Thu, 5 Nov 2020 12:09:06 +0000 (13:09 +0100)]
s390/boot: move sclp early buffer from fixed address in asm to C
To make the decompressor relocatable, the early SCLP buffer with a fixed
address must be replaced with a relocatable C buffer of the according size
and alignment as required by SCLP.
Introduce a new function sclp_early_set_buffer() into the SCLP driver
which enables the decompressor to change the SCLP early buffer at any time.
This will be useful when the decompressor becomes fully relocatable and
might need to change the SCLP early buffer to one with an address < 2G
as required by SCLP because it was loaded at an address >= 2G.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Tue, 15 Jun 2021 13:59:32 +0000 (15:59 +0200)]
s390/boot: get rid of magic numbers for startup offsets
Use STARTUP_NORMAL_OFFSET and STARTUP_KDUMP_OFFSET instead of magic numbers.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Tue, 13 Jul 2021 14:21:24 +0000 (16:21 +0200)]
s390/vdso: use system call functions
Use system call functions instead of open-coding svc inline
assemblies. This is mostly to get rid of even more register asm
constructs.
Besides that, it makes the code also a bit easier to understand.
The generated code is identical to what is was before.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Tue, 13 Jul 2021 14:21:07 +0000 (16:21 +0200)]
s390/syscall: provide generic system call functions
Provide generic system call functions which should be used whenever a
system call needs to be done from user space. The only in-kernel code
is vdso, which will be converted with a follow on patch.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Fri, 25 Jun 2021 14:42:55 +0000 (16:42 +0200)]
s390/cpacf: get rid of register asm
Using register asm statements has been proven to be very error prone,
especially when using code instrumentation where gcc may add function
calls, which clobbers register contents in an unexpected way.
Therefore get rid of register asm statements in cpacf code, and make
sure this bug class cannot happen.
Reviewed-by: Patrick Steuer <patrick.steuer@de.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Tue, 13 Jul 2021 19:09:58 +0000 (21:09 +0200)]
s390/debug: remove unused print defines
Remove unused print defines from debug feature header file.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Tue, 13 Jul 2021 19:07:47 +0000 (21:07 +0200)]
s390/dasd: remove debug printk
Remove dasd ioctl debug printk which seems to be a leftover from the
very early days. At least it seems to be quite pointless.
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Fri, 25 Jun 2021 07:51:15 +0000 (09:51 +0200)]
s390/uv: de-duplicate checks for Protected Host Virtualization
De-duplicate checks for Protected Host Virtualization in decompressor and
kernel.
Set prot_virt_host=0 in the decompressor in *any* of the following cases
and hand it over to the decompressed kernel:
* No explicit prot_virt=1 is given on the kernel command-line
* Protected Guest Virtualization is enabled
* Hardware support not present
* kdump or stand-alone dump
The decompressed kernel needs to use only is_prot_virt_host() instead of
performing again all checks done by the decompressor.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Mon, 5 Jul 2021 17:37:25 +0000 (19:37 +0200)]
s390/boot: disable Secure Execution in dump mode
A dump kernel is neither required nor able to support Secure Execution.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Mon, 5 Jul 2021 17:33:27 +0000 (19:33 +0200)]
s390/boot: move uv function declarations to boot/uv.h
The functions adjust_to_uv_max() and uv_query_info() are used only
in the decompressor. Therefore, move the function declarations from
the global arch/s390/include/asm/uv.h to arch/s390/boot/uv.h.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Mon, 12 Jul 2021 17:26:01 +0000 (19:26 +0200)]
s390/jump_label: print real address in a case of a jump label bug
In case of a jump label print the real address of the piece of code
where a mismatch was detected. This is right before the system panics,
so there is nothing revealed.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Mon, 12 Jul 2021 17:19:03 +0000 (19:19 +0200)]
s390/mm: don't print hashed values for pte_ERROR() & friends
Print the real pte, pmd, etc. values instead of some hashed
value. Otherwise debugging would be even more difficult.
This also matches what most other architectures are doing.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Heiko Carstens [Mon, 12 Jul 2021 17:33:09 +0000 (19:33 +0200)]
s390/mm: use pr_err() instead of printk() for pte_ERROR & friends
Use pr_err() to use a proper printk level.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Sat, 10 Oct 2020 01:34:25 +0000 (03:34 +0200)]
s390/sclp: use only one sclp early buffer to send commands
A buffer that can be used for communication with SCLP is required
to lie below 2GB memory address. Therefore, both sclp_info_sccb
and sclp_early_sccb must fulfill this requirement if passed directly
to the sclp_early_cmd() function. Instead, use only sclp_early_sccb
for communication with SCLP. This allows the buffer sclp_info_sccb
to be placed anywhere in the memory address space and, therefore,
simplifies the process of making the decompressor relocatable later on,
one thing less to relocate. And make sure that the length of the new unified
early SCLP buffer is no less than the length of the removed sclp_info_sccb
buffer which might be larger than the length of the sclp_early_sccb buffer.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Tue, 15 Jun 2021 07:20:26 +0000 (09:20 +0200)]
s390/cio: remove unused include linux/spinlock.h from cio.h
* The linux/spinlock.h header was included indirectly by the decompressor
and brought unnecessary build dependencies.
* Use proper includes in files which either directly or indirectly included
cio.h and were hidden until now by the included linux/spinlock.h, e.g.
linux/string.h for memcpy() or asm/page.h for PAGE_SIZE.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Wed, 30 Jun 2021 15:17:53 +0000 (17:17 +0200)]
s390/boot: make stacks part of the decompressor's image
Instead of using constant addresses for the normal and dump-info stacks,
allocate both stacks in the decompressor's image and load the stack register
in a position-independent manner.
This will allow loading and entering the decompressor at an arbitrary
memory address without corrupting the content at the fixed addresses
used until now for both stacks. This is one of the prerequisites
for being able to kexec the decompressor from its load address without
relocating it first.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Alexander Egorenkov [Wed, 30 Jun 2021 15:12:25 +0000 (17:12 +0200)]
s390/boot: move all linker symbol declarations from c to h files
To prevent multiple incompatible declarations of symbols and to catch
such mistakes at compile time.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Linus Torvalds [Sun, 25 Jul 2021 22:35:14 +0000 (15:35 -0700)]
Linux 5.14-rc3
Linus Torvalds [Sun, 25 Jul 2021 18:06:37 +0000 (11:06 -0700)]
smpboot: fix duplicate and misplaced inlining directive
gcc doesn't care, but clang quite reasonably pointed out that the recent
commit
e9ba16e68cce ("smpboot: Mark idle_init() as __always_inlined to
work around aggressive compiler un-inlining") did some really odd
things:
kernel/smpboot.c:50:20: warning: duplicate 'inline' declaration specifier [-Wduplicate-decl-specifier]
static inline void __always_inline idle_init(unsigned int cpu)
^
which not only has that duplicate inlining specifier, but the new
__always_inline was put in the wrong place of the function definition.
We put the storage class specifiers (ie things like "static" and
"extern") first, and the type information after that. And while the
compiler may not care, we put the inline specifier before the types.
So it should be just
static __always_inline void idle_init(unsigned int cpu)
instead.
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 25 Jul 2021 17:33:48 +0000 (10:33 -0700)]
Merge tag 'powerpc-5.14-3' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix guest to host memory corruption in H_RTAS due to missing nargs
check.
- Fix guest triggerable host crashes due to bad handling of nested
guest TM state.
- Fix possible crashes due to incorrect reference counting in
kvm_arch_vcpu_ioctl().
- Two commits fixing some regressions in KVM transactional memory
handling introduced by the recent rework of the KVM code.
Thanks to Nicholas Piggin, Alexey Kardashevskiy, and Michael Neuling.
* tag 'powerpc-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV Nested: Sanitise H_ENTER_NESTED TM state
KVM: PPC: Book3S: Fix H_RTAS rets buffer overflow
KVM: PPC: Fix kvm_arch_vcpu_ioctl vcpu_load leak
KVM: PPC: Book3S: Fix CONFIG_TRANSACTIONAL_MEM=n crash
KVM: PPC: Book3S HV P9: Fix guest TM support
Linus Torvalds [Sun, 25 Jul 2021 17:27:44 +0000 (10:27 -0700)]
Merge tag 'timers-urgent-2021-07-25' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of timer related fixes:
- Plug a race between rearm and process tick in the posix CPU timers
code
- Make the optimization to avoid recalculation of the next timer
interrupt work correctly when there are no timers pending"
* tag 'timers-urgent-2021-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix get_next_timer_interrupt() with no timers pending
posix-cpu-timers: Fix rearm racing against process tick
Linus Torvalds [Sun, 25 Jul 2021 17:21:19 +0000 (10:21 -0700)]
Merge tag 'locking-urgent-2021-07-25' of git://git./linux/kernel/git/tip/tip
Pull x86 jump label fix from Thomas Gleixner:
"A single fix for jump labels to prevent the compiler from agressive
un-inlining which results in a section mismatch"
* tag 'locking-urgent-2021-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
jump_labels: Mark __jump_label_transform() as __always_inlined to work around aggressive compiler un-inlining
Linus Torvalds [Sun, 25 Jul 2021 17:04:27 +0000 (10:04 -0700)]
Merge tag 'efi-urgent-2021-07-25' of git://git./linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
"A set of EFI fixes:
- Prevent memblock and I/O reserved resources to get out of sync when
EFI memreserve is in use.
- Don't claim a non-existing table is invalid
- Don't warn when firmware memory is already reserved correctly"
* tag 'efi-urgent-2021-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/mokvar: Reserve the table only if it is in boot services data
efi/libstub: Fix the efi_load_initrd function description
firmware/efi: Tell memblock about EFI iomem reservations
efi/tpm: Differentiate missing and invalid final event log table.
Linus Torvalds [Sun, 25 Jul 2021 16:52:48 +0000 (09:52 -0700)]
Merge tag 'core-urgent-2021-07-25' of git://git./linux/kernel/git/tip/tip
Pull core fix from Thomas Gleixner:
"A single update for the boot code to prevent aggressive un-inlining
which causes a section mismatch"
* tag 'core-urgent-2021-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smpboot: Mark idle_init() as __always_inlined to work around aggressive compiler un-inlining
Linus Torvalds [Sun, 25 Jul 2021 16:46:17 +0000 (09:46 -0700)]
Merge tag 'dma-mapping-5.14-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fix from Christoph Hellwig:
- handle vmalloc addresses in dma_common_{mmap,get_sgtable} (Roman
Skakun)
* tag 'dma-mapping-5.14-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: handle vmalloc addresses in dma_common_{mmap,get_sgtable}
Linus Torvalds [Sun, 25 Jul 2021 00:26:47 +0000 (17:26 -0700)]
Merge tag '5.14-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Five cifs/smb3 fixes, including a DFS failover fix, two fallocate
fixes, and two trivial coverity cleanups"
* tag '5.14-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix fallocate when trying to allocate a hole.
CIFS: Clarify SMB1 code for POSIX delete file
CIFS: Clarify SMB1 code for POSIX Create
cifs: support share failover when remounting
cifs: only write 64kb at a time when fallocating a small region of a file
Linus Torvalds [Sat, 24 Jul 2021 22:34:04 +0000 (15:34 -0700)]
Merge tag 'riscv-for-linus-5.14-rc3' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- properly set the memory size, which fixes 32-bit systems
- allow initrd to load anywhere in memory, rather that restricting it
to the first 256MiB
- fix the 'mem=' parameter on 64-bit systems to properly account for
the maximum supported memory now that the kernel is outside the
linear map
- avoid installing mappings into the last 4KiB of memory, which
conflicts with error values
- avoid the stack from being freed while it is being walked
- a handful of fixes to the new copy to/from user routines
* tag 'riscv-for-linus-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: __asm_copy_to-from_user: Fix: Typos in comments
riscv: __asm_copy_to-from_user: Remove unnecessary size check
riscv: __asm_copy_to-from_user: Fix: fail on RV32
riscv: __asm_copy_to-from_user: Fix: overrun copy
riscv: stacktrace: pin the task's stack in get_wchan
riscv: Make sure the kernel mapping does not overlap with IS_ERR_VALUE
riscv: Make sure the linear mapping does not use the kernel mapping
riscv: Fix memory_limit for 64-bit kernel
RISC-V: load initrd wherever it fits into memory
riscv: Fix 32-bit RISC-V boot failure
Linus Torvalds [Sat, 24 Jul 2021 22:25:54 +0000 (15:25 -0700)]
ACPI: fix NULL pointer dereference
Commit
71f642833284 ("ACPI: utils: Fix reference counting in
for_each_acpi_dev_match()") started doing "acpi_dev_put()" on a pointer
that was possibly NULL. That fails miserably, because that helper
inline function is not set up to handle that case.
Just make acpi_dev_put() silently accept a NULL pointer, rather than
calling down to put_device() with an invalid offset off that NULL
pointer.
Link: https://lore.kernel.org/lkml/a607c149-6bf6-0fd0-0e31-100378504da2@kernel.dk/
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Daniel Scally <djrscally@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 24 Jul 2021 20:08:31 +0000 (13:08 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes, all in drivers, all of which can lead to user visible
problems in certain situations"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: Fix NULL dereference on XCOPY completion
scsi: mpt3sas: Transition IOC to Ready state during shutdown
scsi: target: Fix protect handling in WRITE SAME(32)
scsi: iscsi: Fix iface sysfs attr detection
Linus Torvalds [Sat, 24 Jul 2021 20:03:40 +0000 (13:03 -0700)]
Merge tag 'io_uring-5.14-2021-07-24' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Fix a memory leak due to a race condition in io_init_wq_offload
(Yang)
- Poll error handling fixes (Pavel)
- Fix early fdput() regression (me)
- Don't reissue iopoll requests off release path (me)
- Add a safety check for io-wq queue off wrong path (me)
* tag 'io_uring-5.14-2021-07-24' of git://git.kernel.dk/linux-block:
io_uring: explicitly catch any illegal async queue attempt
io_uring: never attempt iopoll reissue from release path
io_uring: fix early fdput() of file
io_uring: fix memleak in io_init_wq_offload()
io_uring: remove double poll entry on arm failure
io_uring: explicitly count entries for poll reqs
Linus Torvalds [Sat, 24 Jul 2021 19:57:06 +0000 (12:57 -0700)]
Merge tag 'block-5.14-2021-07-24' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request (Christoph):
- tracing fix (Keith Busch)
- fix multipath head refcounting (Hannes Reinecke)
- Write Zeroes vs PI fix (me)
- drop a bogus WARN_ON (Zhihao Cheng)
- Increase max blk-cgroup policy size, now that mq-deadline
uses it too (Oleksandr)
* tag 'block-5.14-2021-07-24' of git://git.kernel.dk/linux-block:
nvme: set the PRACT bit when using Write Zeroes with T10 PI
nvme: fix nvme_setup_command metadata trace event
nvme: fix refcounting imbalance when all paths are down
nvme-pci: don't WARN_ON in nvme_reset_work if ctrl.state is not RESETTING
block: increase BLKCG_MAX_POLS
Linus Torvalds [Sat, 24 Jul 2021 19:55:06 +0000 (12:55 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mpc: Poll for MCF
misc: eeprom: at24: Always append device id even if label property is set.
Linus Torvalds [Sat, 24 Jul 2021 19:27:16 +0000 (12:27 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc mm fixes from Andrew Morton:
"15 patches.
VM subsystems affected by this patch series: userfaultfd, kfence,
highmem, pagealloc, memblock, pagecache, secretmem, pagemap, and
hugetlbfs"
* akpm:
hugetlbfs: fix mount mode command line processing
mm: fix the deadlock in finish_fault()
mm: mmap_lock: fix disabling preemption directly
mm/secretmem: wire up ->set_page_dirty
writeback, cgroup: do not reparent dax inodes
writeback, cgroup: remove wb from offline list before releasing refcnt
memblock: make for_each_mem_range() traverse MEMBLOCK_HOTPLUG regions
mm: page_alloc: fix page_poison=1 / INIT_ON_ALLOC_DEFAULT_ON interaction
mm: use kmap_local_page in memzero_page
mm: call flush_dcache_page() in memcpy_to_page() and memzero_page()
kfence: skip all GFP_ZONEMASK allocations
kfence: move the size check to the beginning of __kfence_alloc()
kfence: defer kfence_test_init to ensure that kunit debugfs is created
selftest: use mmap instead of posix_memalign to allocate memory
userfaultfd: do not untag user pointers
Akira Tsukamoto [Tue, 20 Jul 2021 08:53:23 +0000 (17:53 +0900)]
riscv: __asm_copy_to-from_user: Fix: Typos in comments
Fixing typos and grammar mistakes and using more intuitive label
name.
Signed-off-by: Akira Tsukamoto <akira.tsukamoto@gmail.com>
Fixes:
ca6eaaa210de ("riscv: __asm_copy_to-from_user: Optimize unaligned memory access and pipeline stall")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Akira Tsukamoto [Tue, 20 Jul 2021 08:52:36 +0000 (17:52 +0900)]
riscv: __asm_copy_to-from_user: Remove unnecessary size check
Clean up:
The size of 0 will be evaluated in the next step. Not
required here.
Signed-off-by: Akira Tsukamoto <akira.tsukamoto@gmail.com>
Fixes:
ca6eaaa210de ("riscv: __asm_copy_to-from_user: Optimize unaligned memory access and pipeline stall")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Akira Tsukamoto [Tue, 20 Jul 2021 08:51:45 +0000 (17:51 +0900)]
riscv: __asm_copy_to-from_user: Fix: fail on RV32
Had a bug when converting bytes to bits when the cpu was rv32.
The a3 contains the number of bytes and multiple of 8
would be the bits. The LGREG is holding 2 for RV32 and 3 for
RV32, so to achieve multiple of 8 it must always be constant 3.
The 2 was mistakenly used for rv32.
Signed-off-by: Akira Tsukamoto <akira.tsukamoto@gmail.com>
Fixes:
ca6eaaa210de ("riscv: __asm_copy_to-from_user: Optimize unaligned memory access and pipeline stall")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Akira Tsukamoto [Tue, 20 Jul 2021 08:50:52 +0000 (17:50 +0900)]
riscv: __asm_copy_to-from_user: Fix: overrun copy
There were two causes for the overrun memory access.
The threshold size was too small.
The aligning dst require one SZREG and unrolling word copy requires
8*SZREG, total have to be at least 9*SZREG.
Inside the unrolling copy, the subtracting -(8*SZREG-1) would make
iteration happening one extra loop. Proper value is -(8*SZREG).
Signed-off-by: Akira Tsukamoto <akira.tsukamoto@gmail.com>
Fixes:
ca6eaaa210de ("riscv: __asm_copy_to-from_user: Optimize unaligned memory access and pipeline stall")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Mike Kravetz [Fri, 23 Jul 2021 22:50:44 +0000 (15:50 -0700)]
hugetlbfs: fix mount mode command line processing
In commit
32021982a324 ("hugetlbfs: Convert to fs_context") processing
of the mount mode string was changed from match_octal() to fsparam_u32.
This changed existing behavior as match_octal does not require octal
values to have a '0' prefix, but fsparam_u32 does.
Use fsparam_u32oct which provides the same behavior as match_octal.
Link: https://lkml.kernel.org/r/20210721183326.102716-1-mike.kravetz@oracle.com
Fixes:
32021982a324 ("hugetlbfs: Convert to fs_context")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Dennis Camera <bugs+kernel.org@dtnr.ch>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Qi Zheng [Fri, 23 Jul 2021 22:50:41 +0000 (15:50 -0700)]
mm: fix the deadlock in finish_fault()
Commit
63f3655f9501 ("mm, memcg: fix reclaim deadlock with writeback")
fix the following ABBA deadlock by pre-allocating the pte page table
without holding the page lock.
lock_page(A)
SetPageWriteback(A)
unlock_page(A)
lock_page(B)
lock_page(B)
pte_alloc_one
shrink_page_list
wait_on_page_writeback(A)
SetPageWriteback(B)
unlock_page(B)
# flush A, B to clear the writeback
Commit
f9ce0be71d1f ("mm: Cleanup faultaround and finish_fault()
codepaths") reworked the relevant code but ignored this race. This will
cause the deadlock above to appear again, so fix it.
Link: https://lkml.kernel.org/r/20210721074849.57004-1-zhengqi.arch@bytedance.com
Fixes:
f9ce0be71d1f ("mm: Cleanup faultaround and finish_fault() codepaths")
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Muchun Song [Fri, 23 Jul 2021 22:50:38 +0000 (15:50 -0700)]
mm: mmap_lock: fix disabling preemption directly
Commit
832b50725373 ("mm: mmap_lock: use local locks instead of
disabling preemption") fixed a bug by using local locks.
But commit
d01079f3d0c0 ("mm/mmap_lock: remove dead code for
!CONFIG_TRACING configurations") changed those lines back to the
original version.
I guess it was introduced by fixing conflicts.
Link: https://lkml.kernel.org/r/20210720074228.76342-1-songmuchun@bytedance.com
Fixes:
d01079f3d0c0 ("mm/mmap_lock: remove dead code for !CONFIG_TRACING configurations")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Fri, 23 Jul 2021 22:50:35 +0000 (15:50 -0700)]
mm/secretmem: wire up ->set_page_dirty
Make secretmem up to date with the changes done in commit
0af573780b0b
("mm: require ->set_page_dirty to be explicitly wired up") so that
unconditional call to this method won't cause crashes.
Link: https://lkml.kernel.org/r/20210716063933.31633-1-rppt@kernel.org
Fixes:
0af573780b0b ("mm: require ->set_page_dirty to be explicitly wired up")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>