OSDN Git Service
Guennadi Liakhovetski [Mon, 20 Jun 2011 15:02:47 +0000 (17:02 +0200)]
dmaengine: failure to get a specific DMA channel is not critical
There exist systems with multiple DMA controllers with different
capabilities. For example, on some sh-mobile / rmobile systems there are
DMA controllers, whose channels can be configured to be used with
SD- and MMC-host controllers, serial ports etc. Besides there are also
DMA controllers, that can only be used for one special function, e.g.,
for USB. In such cases the DMA client filter function can just choose
to specify to the DMA driver, which channel it needs. Then the
.device_alloc_chan_resources() method of the DMA driver will check,
whether it can provide that dunction. If not, it will fail and the loop
in __dma_request_channel() will continue to the next DMA device, until
it finds a suitable one. This works fine with just one minor glitch:
the kernel logs error messages like
dmaengine: failed to get <channel name>: (-<error code>)
after each such non-critical failure. This patch lowers priority of
this message to the debug level.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
H Hartley Sweeten [Fri, 10 Jun 2011 22:15:05 +0000 (15:15 -0700)]
dma/ep93xx_dma.c: local symbols should be static
The symbol 'ep93xx_dma_prep_dma_memcpy' is only used in this driver
and should be marked static.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul [Thu, 9 Jun 2011 16:37:05 +0000 (22:07 +0530)]
Merge remote branch 'gpio/ep93xx-dma' into next
Mika Westerberg [Sun, 29 May 2011 10:10:06 +0000 (13:10 +0300)]
spi/ep93xx: add DMA support
This patch adds DMA support for the EP93xx SPI driver. By default the DMA is
not enabled but it can be enabled by setting ep93xx_spi_info.use_dma to true
in board configuration file.
Note that the SPI driver still uses PIO for small transfers (<= 8 bytes) for
performance reasons.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Mika Westerberg [Sun, 29 May 2011 10:10:05 +0000 (13:10 +0300)]
ep93xx: remove the old M2P DMA code
Since we have converted all existing users of the old DMA API to use the DMA
engine API the old code can be dropped.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Mika Westerberg [Sun, 29 May 2011 10:10:04 +0000 (13:10 +0300)]
ASoC: ep93xx: convert to use the DMA engine API
Now that we have the EP93xx DMA engine driver in place, we convert the ASoC
drivers (I2S, AC97 and PCM) to take advantage of this new API. There are no
functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Mika Westerberg [Sun, 29 May 2011 10:10:03 +0000 (13:10 +0300)]
ep93xx: add dmaengine platform code
Add platform support code for the new EP93xx dmaengine driver.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Mika Westerberg [Sun, 29 May 2011 10:10:02 +0000 (13:10 +0300)]
dmaengine: add ep93xx DMA support
The ep93xx DMA controller has 10 independent memory to peripheral (M2P)
channels, and 2 dedicated memory to memory (M2M) channels. M2M channels can
also be used by SPI and IDE to perform DMA transfers to/from their memory
mapped FIFOs.
This driver supports both M2P and M2M channels with DMA_SLAVE, DMA_CYCLIC and
DMA_MEMCPY (M2M only) capabilities.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Grant Likely [Wed, 8 Jun 2011 20:37:22 +0000 (14:37 -0600)]
Merge remote-tracking branch 'origin' into spi/merge
Geert Uytterhoeven [Wed, 8 Jun 2011 19:48:03 +0000 (21:48 +0200)]
spi/rtc-m41t93: Use spi_get_drvdata() for SPI devices
One new offender detected by the recently increased type checking in
platform_get_drvdata():
drivers/rtc/rtc-m41t93.c: In function ‘m41t93_remove’:
drivers/rtc/rtc-m41t93.c:192: warning: passing argument 1 of ‘platform_get_drvdata’ from incompatible pointer type
Use spi_get_drvdata() instead of platform_get_drvdata(), cfr. commit
42fea15d6dc410e62dac6a764142045280624a5b ("spi/rtc-{ds1390,ds3234,m41t94}:
Use spi_get_drvdata() for SPI devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Linus Torvalds [Mon, 6 Jun 2011 09:06:33 +0000 (18:06 +0900)]
Linux 3.0-rc2
Hugh Dickins [Mon, 6 Jun 2011 05:03:13 +0000 (22:03 -0700)]
mm: fix ENOSPC returned by handle_mm_fault()
Al Viro observes that in the hugetlb case, handle_mm_fault() may return
a value of the kind ENOSPC when its caller is expecting a value of the
kind VM_FAULT_SIGBUS: fix alloc_huge_page()'s failure returns.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 6 Jun 2011 08:51:28 +0000 (17:51 +0900)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: usb - turn off de-emphasis in s/pdif for cm6206
ALSA: asihpi: Use angle brackets for system includes
ALSA: fm801: add error handling if auto-detect fails
ALSA: hda - Check pin support EAPD in ad198x_power_eapd_write
ALSA: hda - Fix HP and Front pins of ad1988/ad1989 in ad198x_power_eapd()
ALSA: 6fire: Don't leak firmware in error path
ASoC: Fix wm_hubs input PGA ZC bits
ASoC: Fix dapm_is_shared_kcontrol so everything isn't shared
Linus Torvalds [Mon, 6 Jun 2011 08:48:02 +0000 (17:48 +0900)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (max6642): Better chip detection schema
hwmon: (coretemp) Further relax temperature range checks
hwmon: (coretemp) Fix TjMax detection for older CPUs
hwmon: (coretemp) Relax target temperature range check
hwmon: (max6642) Rename temp_fault sysfs attribute to temp2_fault
H Hartley Sweeten [Wed, 1 Jun 2011 22:16:09 +0000 (15:16 -0700)]
dma: at_hdmac.c: use resource_size
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
H Hartley Sweeten [Wed, 1 Jun 2011 22:10:30 +0000 (15:10 -0700)]
dma: ipu_idmac.c: use resource_size in ioremap
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Takashi Iwai [Mon, 6 Jun 2011 07:28:49 +0000 (09:28 +0200)]
Merge branch 'fix/asoc' into for-linus
Mika Westerberg [Sun, 29 May 2011 10:10:06 +0000 (13:10 +0300)]
spi/ep93xx: add DMA support
This patch adds DMA support for the EP93xx SPI driver. By default the DMA is
not enabled but it can be enabled by setting ep93xx_spi_info.use_dma to true
in board configuration file.
Note that the SPI driver still uses PIO for small transfers (<= 8 bytes) for
performance reasons.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Mika Westerberg [Sun, 29 May 2011 10:10:05 +0000 (13:10 +0300)]
ep93xx: remove the old M2P DMA code
Since we have converted all existing users of the old DMA API to use the DMA
engine API the old code can be dropped.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Mika Westerberg [Sun, 29 May 2011 10:10:04 +0000 (13:10 +0300)]
ASoC: ep93xx: convert to use the DMA engine API
Now that we have the EP93xx DMA engine driver in place, we convert the ASoC
drivers (I2S, AC97 and PCM) to take advantage of this new API. There are no
functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Mika Westerberg [Sun, 29 May 2011 10:10:03 +0000 (13:10 +0300)]
ep93xx: add dmaengine platform code
Add platform support code for the new EP93xx dmaengine driver.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Mika Westerberg [Sun, 29 May 2011 10:10:02 +0000 (13:10 +0300)]
dmaengine: add ep93xx DMA support
The ep93xx DMA controller has 10 independent memory to peripheral (M2P)
channels, and 2 dedicated memory to memory (M2M) channels. M2M channels can
also be used by SPI and IDE to perform DMA transfers to/from their memory
mapped FIFOs.
This driver supports both M2P and M2M channels with DMA_SLAVE, DMA_CYCLIC and
DMA_MEMCPY (M2M only) capabilities.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Linus Torvalds [Sat, 4 Jun 2011 23:11:11 +0000 (08:11 +0900)]
Merge branch 'for-linus' of git://android.git./kernel/tegra
* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
ARM: Tegra: Harmony: Fix conflicting GPIO numbering
Stephen Warren [Tue, 31 May 2011 21:14:07 +0000 (15:14 -0600)]
ARM: Tegra: Harmony: Fix conflicting GPIO numbering
Currently, both the WM8903 and TPS6586x chips attempt to register with
gpiolib using the same GPIO numbers. This causes the audio driver to
fail to initialize.
To solve this, add a define to board-harmony.h for the TPS6586x, and make
board-harmony-power.c use this define, instead of directly referencing
TEGRA_NR_GPIOS.
This fixes a regression introduced by commit
6f168f2fa60f87e85e0df25e87e2372f22f5eb7c.
ARM: tegra: harmony: initialize the TPS65862 PMIC
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Linus Torvalds [Sat, 4 Jun 2011 21:17:23 +0000 (06:17 +0900)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/btrfs-unstable
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (25 commits)
btrfs: fix uninitialized variable warning
btrfs: add helper for fs_info->closing
Btrfs: add mount -o inode_cache
btrfs: scrub: add explicit plugging
btrfs: use btrfs_ino to access inode number
Btrfs: don't save the inode cache if we are deleting this root
btrfs: false BUG_ON when degraded
Btrfs: don't save the inode cache in non-FS roots
Btrfs: make sure we don't overflow the free space cache crc page
Btrfs: fix uninit variable in the delayed inode code
btrfs: scrub: don't reuse bios and pages
Btrfs: leave spinning on lookup and map the leaf
Btrfs: check for duplicate entries in the free space cache
Btrfs: don't try to allocate from a block group that doesn't have enough space
Btrfs: don't always do readahead
Btrfs: try not to sleep as much when doing slow caching
Btrfs: kill BTRFS_I(inode)->block_group
Btrfs: don't look at the extent buffer level 3 times in a row
Btrfs: map the node block when looking for readahead targets
Btrfs: set range_start to the right start in count_range_bits
...
Per Dalén [Thu, 26 May 2011 13:08:53 +0000 (09:08 -0400)]
hwmon: (max6642): Better chip detection schema
Improve detection of MAX6642 by reading non existing registers (0x04, 0x06
and 0xff). Reading those registers returns the previously read value.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
[guenter.roeck@ericsson.com: added second set of register reads]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Linus Torvalds [Sat, 4 Jun 2011 14:19:51 +0000 (23:19 +0900)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] Fix oops caused by queue refcounting failure
Linus Torvalds [Sat, 4 Jun 2011 14:16:00 +0000 (23:16 +0900)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
tg3: Fix tg3_skb_error_unmap()
net: tracepoint of net_dev_xmit sees freed skb and causes panic
drivers/net/can/flexcan.c: add missing clk_put
net: dm9000: Get the chip in a known good state before enabling interrupts
drivers/net/davinci_emac.c: add missing clk_put
af-packet: Add flag to distinguish VID 0 from no-vlan.
caif: Fix race when conditionally taking rtnl lock
usbnet/cdc_ncm: add missing .reset_resume hook
vlan: fix typo in vlan_dev_hard_start_xmit()
net/ipv4: Check for mistakenly passed in non-IPv4 address
iwl4965: correctly validate temperature value
bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
ath9k: fix two more bugs in tx power
cfg80211: don't drop p2p probe responses
Revert "net: fix section mismatches"
drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()
sctp: stop pending timers and purge queues when peer restart asoc
drivers/net: ks8842 Fix crash on received packet when in PIO mode.
ip_options_compile: properly handle unaligned pointer
iwlagn: fix incorrect PCI subsystem id for 6150 devices
...
David Sterba [Fri, 3 Jun 2011 14:29:08 +0000 (16:29 +0200)]
btrfs: fix uninitialized variable warning
With Linus' tree, today's linux-next build (powercp ppc64_defconfig)
produced this warning:
fs/btrfs/delayed-inode.c: In function 'btrfs_delayed_update_inode':
fs/btrfs/delayed-inode.c:1598:6: warning: 'ret' may be used
uninitialized in this function
Introduced by commit
16cdcec736cd ("btrfs: implement delayed inode items
operation").
This fixes a bug in btrfs_update_inode(): if the returned value from
btrfs_delayed_update_inode is a nonzero garbage, inode stat data are not
updated and several call paths may hit a BUG_ON or fail with strange
code.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Sterba <dsterba@suse.cz>
David Sterba [Tue, 31 May 2011 16:07:27 +0000 (18:07 +0200)]
btrfs: add helper for fs_info->closing
wrap checking of filesystem 'closing' flag and fix a few missing memory
barriers.
Signed-off-by: David Sterba <dsterba@suse.cz>
Chris Mason [Fri, 3 Jun 2011 13:36:29 +0000 (09:36 -0400)]
Btrfs: add mount -o inode_cache
This makes the inode map cache default to off until we
fix the overflow problem when the free space crcs don't fit
inside a single page.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Arne Jansen [Sat, 28 May 2011 20:58:38 +0000 (20:58 +0000)]
btrfs: scrub: add explicit plugging
With the removal of the implicit plugging scrub ends up doing more and
smaller I/O than necessary. This patch adds explicit plugging per chunk.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
David Sterba [Tue, 31 May 2011 17:08:14 +0000 (17:08 +0000)]
btrfs: use btrfs_ino to access inode number
commit
4cb5300bc ("Btrfs: add mount -o auto_defrag") accesses inode
number directly while it should use the helper with the new inode
number allocator.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Tue, 31 May 2011 19:33:33 +0000 (19:33 +0000)]
Btrfs: don't save the inode cache if we are deleting this root
With xfstest 254 I can panic the box every time with the inode number caching
stuff on. This is because we clean the inodes out when we delete the subvolume,
but then we write out the inode cache which adds an inode to the subvolume inode
tree, and then when it gets evicted again the root gets added back on the dead
roots list and is deleted again, so we have a double free. To stop this from
happening just return 0 if refs is 0 (and we're not the tree root since tree
root always has refs of 0). With this fix 254 no longer panics. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Tested-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Arne Jansen [Mon, 30 May 2011 08:36:16 +0000 (08:36 +0000)]
btrfs: false BUG_ON when degraded
In degraded mode the struct btrfs_device of missing devs don't have
device->name set. A kstrdup of NULL correctly returns NULL. Don't
BUG in this case.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
liubo [Wed, 1 Jun 2011 09:42:49 +0000 (09:42 +0000)]
Btrfs: don't save the inode cache in non-FS roots
This adds extra checks to make sure the inode map we are caching really
belongs to a FS root instead of a special relocation tree. It
prevents crashes during balancing operations.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Fri, 3 Jun 2011 05:26:53 +0000 (01:26 -0400)]
Btrfs: make sure we don't overflow the free space cache crc page
The free space cache uses only one page for crcs right now,
which means we can't have a cache file bigger than the
crcs we can fit in the first page. This adds a check to
enforce that restriction.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Fri, 3 Jun 2011 05:13:45 +0000 (01:13 -0400)]
Btrfs: fix uninit variable in the delayed inode code
The nitems counter needs to start at zero
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Arne Jansen [Sat, 28 May 2011 19:57:55 +0000 (21:57 +0200)]
btrfs: scrub: don't reuse bios and pages
The current scrub implementation reuses bios and pages as often as possible,
allocating them only on start and releasing them when finished. This leads
to more problems with the block layer than it's worth. The elevator gets
confused when there are more pages added to the bio than bi_size suggests.
This patch completely rips out the reuse of bios and pages and allocates
them freshly for each submit.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Chris Maosn <chris.mason@oracle.com>
Linus Torvalds [Fri, 3 Jun 2011 23:11:26 +0000 (08:11 +0900)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Use hlist_entry() for io_context.cic_list.first
cfq-iosched: Remove bogus check in queue_fail path
xen/blkback: potential null dereference in error handling
xen/blkback: don't call vbd_size() if bd_disk is NULL
block: blkdev_get() should access ->bd_disk only after success
CFQ: Fix typo and remove unnecessary semicolon
block: remove unwanted semicolons
Revert "block: Remove extra discard_alignment from hd_struct."
nbd: adjust 'max_part' according to part_shift
nbd: limit module parameters to a sane value
nbd: pass MSG_* flags to kernel_recvmsg()
block: improve the bio_add_page() and bio_add_pc_page() descriptions
Linus Torvalds [Fri, 3 Jun 2011 23:04:10 +0000 (08:04 +0900)]
Merge branch 'for-linus' of git://git./linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: strncpy: fix handling of zero lengths
Linus Torvalds [Fri, 3 Jun 2011 23:03:16 +0000 (08:03 +0900)]
Merge branch 'stable' of git://git./linux/kernel/git/cmetcalf/linux-tile
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
asm-generic/unistd.h: support sendmmsg syscall
tile: enable CONFIG_BUGVERBOSE
Linus Torvalds [Fri, 3 Jun 2011 22:59:32 +0000 (07:59 +0900)]
Merge branch 'linux-next' of git://git.infradead.org/ubifs-2.6
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: fix-up free space earlier
UBIFS: intialize LPT earlier
UBIFS: assert no fixup when writing a node
UBIFS: fix clean znode counter corruption in error cases
UBIFS: fix memory leak on error path
UBIFS: fix shrinker object count reports
UBIFS: fix recovery broken by the previous recovery fix
UBIFS: amend ubifs_recover_leb interface
UBIFS: introduce a "grouped" journal head flag
UBIFS: supress false error messages
Linus Torvalds [Fri, 3 Jun 2011 22:58:48 +0000 (07:58 +0900)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rostedt/linux-2.6-ktest
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-ktest:
ktest: Ignore unset values of the minconfig in config_bisect
ktest: Fix result of rebooting the kernel
ktest: Fix off-by-one in config bisect result
Linus Torvalds [Fri, 3 Jun 2011 22:53:23 +0000 (07:53 +0900)]
Merge branch 'rmobile-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: add DMAC clock definitions on SH7372
ARM: arch-shmobile: support SDHI card detection on mackerel, using a GPIO
sh_mobile_meram: MERAM platform data for LCDC
Linus Torvalds [Fri, 3 Jun 2011 22:04:25 +0000 (07:04 +0900)]
Merge branch 'sh-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
dmaengine: shdma: fix a regression: initialise DMA channels for memcpy
dmaengine: shdma: Fix up fallout from runtime PM changes.
Revert "clocksource: sh_cmt: Runtime PM support"
Revert "clocksource: sh_tmu: Runtime PM support"
sh: Fix up asm-generic/ptrace.h fallout.
sh64: Move from P1SEG to CAC_ADDR for consistent sync.
sh64: asm/pgtable.h needs asm/mmu.h
sh: asm/tlb.h needs linux/swap.h
sh: mark DMA slave ID 0 as invalid
sh: Update shmin to reflect PIO dependency.
sh: arch/sh/kernel/process_32.c needs linux/prefetch.h.
sh: add MMCIF runtime PM support on ecovec
sh: switch ap325rxa to dynamically manage the platform camera
Linus Torvalds [Fri, 3 Jun 2011 22:00:50 +0000 (07:00 +0900)]
Revert "ASoC: Update cx20442 for TTY API change"
This reverts commit
ed0bd2333cffc3d856db9beb829543c1dfc00982.
Since we reverted the TTY API change, we should revert the ASoC update
to it too.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 3 Jun 2011 21:33:24 +0000 (06:33 +0900)]
Revert "tty: make receive_buf() return the amout of bytes received"
This reverts commit
b1c43f82c5aa265442f82dba31ce985ebb7aa71c.
It was broken in so many ways, and results in random odd pty issues.
It re-introduced the buggy schedule_work() in flush_to_ldisc() that can
cause endless work-loops (see commit
a5660b41af6a: "tty: fix endless
work loop when the buffer fills up").
It also used an "unsigned int" return value fo the ->receive_buf()
function, but then made multiple functions return a negative error code,
and didn't actually check for the error in the caller.
And it didn't actually work at all. BenH bisected down odd tty behavior
to it:
"It looks like the patch is causing some major malfunctions of the X
server for me, possibly related to PTYs. For example, cat'ing a
large file in a gnome terminal hangs the kernel for -minutes- in a
loop of what looks like flush_to_ldisc/workqueue code, (some ftrace
data in the quoted bits further down).
...
Some more data: It -looks- like what happens is that the
flush_to_ldisc work queue entry constantly re-queues itself (because
the PTY is full ?) and the workqueue thread will basically loop
forver calling it without ever scheduling, thus starving the consumer
process that could have emptied the PTY."
which is pretty much exactly the problem we fixed in
a5660b41af6a.
Milton Miller pointed out the 'unsigned int' issue.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Milton Miller <miltonm@bga.com>
Cc: Stefan Bigler <stefan.bigler@keymile.com>
Cc: Toby Gray <toby.gray@realvnc.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Govindraj.R [Wed, 1 Jun 2011 06:01:24 +0000 (11:31 +0530)]
spi/omap2: fix uninitialized variable
fixes below compilation warning. The variable doesn't actual ever get
used uninitialized, but that's no reason to be sloppy.
drivers/spi/omap2_mcspi.c: In function 'omap2_mcspi_txrx_dma':
drivers/spi/omap2_mcspi.c:301: warning: 'elements' may be used uninitialized in this function
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[grant.likely: amended description]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
John W. Linville [Fri, 3 Jun 2011 18:31:50 +0000 (14:31 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6 into for-davem
Eric Lammerts [Fri, 27 May 2011 22:16:52 +0000 (18:16 -0400)]
ALSA: usb - turn off de-emphasis in s/pdif for cm6206
CM6206: Turn off de-emphasis channel status bit in S/PDIF output.
Signed-off-by: Eric Lammerts <eric@lammerts.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ben Gardiner [Mon, 30 May 2011 18:56:16 +0000 (14:56 -0400)]
UBIFS: fix-up free space earlier
The free space fixup is currently initiated during mount after the call to
ubifs_write_master() which results in a write to PEBs; this has been observed
with the patch 'assert no fixup when writing a node' applied:
Move the free space fixup on mount to before the calls to
ubifs_recover_inl_heads() and ubifs_write_master(). This results in no
assertions with the previously mentioned patch applied.
Artem: tweaked the patch a bit
Signed-off-by: Ben Gardiner <bengardiner@nanometrics>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Ben Gardiner [Mon, 30 May 2011 18:56:15 +0000 (14:56 -0400)]
UBIFS: intialize LPT earlier
The current 'mount_ubifs()' implementation does not initialize the LPT until the
the master node is marked dirty. Move the LPT initialization to before marking
the master node dirty. This is a preparation for the next patch which will move
the free-space-fixup check to before marking the master node dirty, because we
have to fix-up the free space before doing any writes.
Artem: massaged the patch and commit message.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Ben Gardiner [Mon, 30 May 2011 18:56:14 +0000 (14:56 -0400)]
UBIFS: assert no fixup when writing a node
The current free space fixup can result in some writing to the UBI volume
when the space_fixup flag is set.
To catch instances where UBIFS is writing to the NAND while the space_fixup
flag is set, add an assert to ubifs_write_node().
Artem: tweaked the patch, added similar assertion to the write buffer
write path.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Artem Bityutskiy [Tue, 31 May 2011 11:26:07 +0000 (14:26 +0300)]
UBIFS: fix clean znode counter corruption in error cases
UBIFS maintains per-filesystem and global clean znode counters
('c->clean_zn_cnt' and 'ubifs_clean_zn_cnt'). It is important to maintain
correct values there since the shrinker relies on 'ubifs_clean_zn_cnt'.
However, in case of failures during commit the counters were corrupted. E.g.,
if a failure happens in the middle of 'write_index()', then some nodes in the
commit list ('c->cnext') are marked as clean, and some are marked as dirty. And
the 'ubifs_destroy_tnc_subtree()' frees does not retrun correct count, and we
end up with non-zero 'c->clean_zn_cnt' when unmounting. This means that if we
have 2 file-sytem and one of them fails, and we unmount it,
'ubifs_clean_zn_cnt' stays incorrect and confuses the shrinker.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Artem Bityutskiy [Tue, 31 May 2011 05:40:40 +0000 (08:40 +0300)]
UBIFS: fix memory leak on error path
UBIFS leaks memory on error path in 'ubifs_jnl_update()' in case of write
failure because it forgets to free the 'struct ubifs_dent_node *dent' object.
Although the object is small, the alignment can make it large - e.g., 2KiB
if the min. I/O unit is 2KiB.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
Artem Bityutskiy [Tue, 31 May 2011 04:03:21 +0000 (07:03 +0300)]
UBIFS: fix shrinker object count reports
Sometimes VM asks the shrinker to return amount of objects it can shrink,
and we return the ubifs_clean_zn_cnt in that case. However, it is possible
that this counter is negative for a short period of time, due to the way
UBIFS TNC code updates it. And I can observe the following warnings sometimes:
shrink_slab: ubifs_shrinker+0x0/0x2b7 [ubifs] negative objects to delete nr=-
8541616642706119788
This patch makes sure UBIFS never returns negative count of objects.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
Steven Miao [Wed, 1 Jun 2011 07:52:41 +0000 (15:52 +0800)]
Blackfin: strncpy: fix handling of zero lengths
The jump to 4f will cause the NUL padding loop to run at least one time,
so if string length is zero just jump to the end. Otherwise we wrongly
write one NUL byte when size==0.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Joe Perches [Fri, 3 Jun 2011 09:28:49 +0000 (02:28 -0700)]
ALSA: asihpi: Use angle brackets for system includes
Use the normal include style.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Carpenter [Thu, 26 May 2011 08:47:35 +0000 (11:47 +0300)]
ALSA: fm801: add error handling if auto-detect fails
In the original code if auto detect failed and tea575x_tuner == 4
then we copy bogus information to chip->tea.card. I've changed the
autodetect code to cleanup and return -ENODEV on error instead.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Raymond Yau [Wed, 1 Jun 2011 07:09:48 +0000 (15:09 +0800)]
ALSA: hda - Check pin support EAPD in ad198x_power_eapd_write
Check whether the pin supports EAPD in ad198x_power_eapd_write.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 3 Jun 2011 08:05:02 +0000 (10:05 +0200)]
ALSA: hda - Fix HP and Front pins of ad1988/ad1989 in ad198x_power_eapd()
In ad198x_power_eapd(), wrong pin NIDs are used for controlling EAPD for
HP and Front outputs of AD1988/AD1989. These are actually same with the
ones for AD1984 & co, port-A is 0x11 and port-D 0x12.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Matt Carlson [Thu, 2 Jun 2011 13:01:39 +0000 (13:01 +0000)]
tg3: Fix tg3_skb_error_unmap()
This function attempts to free one fragment beyond the number of
fragments that were actually mapped. This patch brings back the limit
to the correct spot.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Koki Sanagi [Mon, 30 May 2011 21:48:34 +0000 (21:48 +0000)]
net: tracepoint of net_dev_xmit sees freed skb and causes panic
Because there is a possibility that skb is kfree_skb()ed and zero cleared
after ndo_start_xmit, we should not see the contents of skb like skb->len and
skb->dev->name after ndo_start_xmit. But trace_net_dev_xmit does that
and causes panic by NULL pointer dereference.
This patch fixes trace_net_dev_xmit not to see the contents of skb directly.
If you want to reproduce this panic,
1. Get tracepoint of net_dev_xmit on
2. Create 2 guests on KVM
2. Make 2 guests use virtio_net
4. Execute netperf from one to another for a long time as a network burden
5. host will panic(It takes about 30 minutes)
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Metcalf [Thu, 2 Jun 2011 18:21:45 +0000 (14:21 -0400)]
asm-generic/unistd.h: support sendmmsg syscall
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Jesper Juhl [Mon, 30 May 2011 10:49:01 +0000 (12:49 +0200)]
ALSA: 6fire: Don't leak firmware in error path
One of the error paths in
sound/usb/6fire/firmware.c::usb6fire_fw_ezusb_upload() neglects to free
the memory allocated for the firmware before returning, thus leaking the
memory.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Steven Rostedt [Thu, 2 Jun 2011 03:27:19 +0000 (23:27 -0400)]
ktest: Ignore unset values of the minconfig in config_bisect
By ignoring the unset values of the minconfig in deciding
what to test in the config_bisect can cause the problem
config from being tested too.
Just do not test the configs that are set in the minconfig.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Thu, 2 Jun 2011 03:25:13 +0000 (23:25 -0400)]
ktest: Fix result of rebooting the kernel
The command that is called that reboots the kernel may fail
but the return code is not passed back to the ktest.pl script.
This is because a ';' is used between the two commands and
if the second command fails, only the first command's return
code is returned. Using a '&&' between the two commands fixes
this.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt [Thu, 2 Jun 2011 03:22:30 +0000 (23:22 -0400)]
ktest: Fix off-by-one in config bisect result
Because in perl the array size returned by $#arr, is the last
index and not the actually size of the array, we end the config
bisect early, thinking there is only one config left when there
are in fact two. Thus the result has a 50% chance of picking
the correct config that caused the problem.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Jens Axboe [Thu, 2 Jun 2011 11:14:15 +0000 (13:14 +0200)]
Merge branch 'for-jens/xen-blkback.fixes' of git://git./linux/kernel/git/konrad/xen into for-linus
Paul Bolle [Thu, 2 Jun 2011 11:05:02 +0000 (13:05 +0200)]
block: Use hlist_entry() for io_context.cic_list.first
list_entry() and hlist_entry() are both simply aliases for
container_of(), but since io_context.cic_list.first is an hlist_node one
should at least use the correct alias.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Paul Bolle [Thu, 2 Jun 2011 11:05:02 +0000 (13:05 +0200)]
cfq-iosched: Remove bogus check in queue_fail path
queue_fail can only be reached if cic is NULL, so its check for cic must
be bogus.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
James Bottomley [Wed, 25 May 2011 20:52:14 +0000 (15:52 -0500)]
[SCSI] Fix oops caused by queue refcounting failure
In certain circumstances, we can get an oops from a torn down device.
Most notably this is from CD roms trying to call scsi_ioctl. The root
cause of the problem is the fact that after scsi_remove_device() has
been called, the queue is fully torn down. This is actually wrong
since the queue can be used until the sdev release function is called.
Therefore, we add an extra reference to the queue which is released in
sdev->release, so the queue always exists.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Julia Lawall [Wed, 1 Jun 2011 19:48:50 +0000 (19:48 +0000)]
drivers/net/can/flexcan.c: add missing clk_put
The failed_get label is used after the call to clk_get has succeeded, so it
should be moved up above the call to clk_put.
The failed_req labels doesn't do anything different than failed_get, so
delete it.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guennadi Liakhovetski [Wed, 1 Jun 2011 07:32:07 +0000 (07:32 +0000)]
ARM: mach-shmobile: add DMAC clock definitions on SH7372
These definitions are needed to let the runtime PM subsystem turn off
DMAC clocks, when it is suspended by the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Guennadi Liakhovetski [Tue, 31 May 2011 09:25:16 +0000 (09:25 +0000)]
dmaengine: shdma: fix a regression: initialise DMA channels for memcpy
A recent patch has introduced a regression, where repeating a memcpy
DMA test with shdma module unloading between them skips the DMA channel
configuration. Fix this regression by always configuring the channel
during its allocation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Mark Brown [Wed, 1 Jun 2011 10:18:09 +0000 (10:18 +0000)]
net: dm9000: Get the chip in a known good state before enabling interrupts
Currently the DM9000 driver requests the primary interrupt before it
resets the chip and puts it into a known good state. This means that if
the chip is asserting interrupt for some reason we can end up with a
screaming IRQ that the interrupt handler is unable to deal with. Avoid
this by only requesting the interrupt after we've reset the chip so we
know what state it's in.
This started manifesting itself on one of my boards in the past month or
so, I suspect as a result of some core infrastructure changes removing
some form of mitigation against bad behaviour here, even when things boot
it seems that the new code brings the interface up more quickly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Wed, 1 Jun 2011 07:10:10 +0000 (07:10 +0000)]
drivers/net/davinci_emac.c: add missing clk_put
Go to existing error handling code at the end of the function that calls
clk_put.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Greear [Wed, 1 Jun 2011 06:49:10 +0000 (06:49 +0000)]
af-packet: Add flag to distinguish VID 0 from no-vlan.
Currently, user-space cannot determine if a 0 tcp_vlan_tci
means there is no VLAN tag or the VLAN ID was zero.
Add flag to make this explicit. User-space can check for
TP_STATUS_VLAN_VALID || tp_vlan_tci > 0, which will be backwards
compatible. Older could would have just checked for tp_vlan_tci,
so it will work no worse than before.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sjur.brandeland@stericsson.com [Wed, 1 Jun 2011 00:55:37 +0000 (00:55 +0000)]
caif: Fix race when conditionally taking rtnl lock
Take the RTNL lock unconditionally when calling dev_close.
Taking the lock conditionally may cause race conditions.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Metzmacher [Wed, 1 Jun 2011 02:01:41 +0000 (02:01 +0000)]
usbnet/cdc_ncm: add missing .reset_resume hook
This avoids messages like this after suspend:
cdc_ncm 2-1.4:1.6: no reset_resume for driver cdc_ncm?
cdc_ncm 2-1.4:1.7: no reset_resume for driver cdc_ncm?
cdc_ncm 2-1.4:1.6: usb0: unregister 'cdc_ncm' usb-0000:00:1d.0-1.4, CDC NCM
This is important for the Ericsson F5521gw GSM/UMTS modem.
Otherwise modemmanager looses the fact that the cdc_ncm and cdc_acm devices
belong together.
The cdc_ether module does the same.
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 31 May 2011 22:53:19 +0000 (22:53 +0000)]
vlan: fix typo in vlan_dev_hard_start_xmit()
commit
4af429d29b341bb1735f04c2fb960178ed5d52e7 (vlan: lockless
transmit path) have a typo in vlan_dev_hard_start_xmit(), using
u64_stats_update_begin() to end the stat update, it should be
u64_stats_update_end().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcus Meissner [Thu, 2 Jun 2011 04:05:22 +0000 (21:05 -0700)]
net/ipv4: Check for mistakenly passed in non-IPv4 address
Check against mistakenly passing in IPv6 addresses (which would result
in an INADDR_ANY bind) or similar incompatible sockaddrs.
Signed-off-by: Marcus Meissner <meissner@suse.de>
Cc: Reinhard Max <max@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Wed, 1 Jun 2011 18:03:41 +0000 (11:03 -0700)]
hwmon: (coretemp) Further relax temperature range checks
Further relax temperature range checks after reading the IA32_TEMPERATURE_TARGET
register. If the register returns a value other than 0 in bits 16..32, assume
that the returned value is correct.
This change applies to both packet and core temperature limits.
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Guenter Roeck [Tue, 31 May 2011 13:54:21 +0000 (06:54 -0700)]
hwmon: (coretemp) Fix TjMax detection for older CPUs
Commit
a321cedb12904114e2ba5041a3673ca24deb09c9 excludes CPU models 0xe, 0xf,
0x16, and 0x1a from TjMax temperature adjustment, even though several of those
CPUs are known to have TiMax other than 100 degrees C, and even though the code
in adjust_tjmax() explicitly handles those CPUs and points to a Web document
listing several of the affected CPU IDs.
Reinstate original TjMax adjustment if TjMax can not be determined using the
IA32_TEMPERATURE_TARGET register.
https://bugzilla.kernel.org/show_bug.cgi?id=32582
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Yong Wang <yong.y.wang@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: <stable@kernel.org> # .35.x .36.x .37.x .38.x .39.x
Linus Torvalds [Wed, 1 Jun 2011 21:11:24 +0000 (06:11 +0900)]
Revert "mm: fail GFP_DMA allocations when ZONE_DMA is not configured"
This reverts commit
a197b59ae6e8bee56fcef37ea2482dc08414e2ac.
As rmk says:
"Commit
a197b59ae6e8 (mm: fail GFP_DMA allocations when ZONE_DMA is not
configured) is causing regressions on ARM with various drivers which
use GFP_DMA.
The behaviour up until now has been to silently ignore that flag when
CONFIG_ZONE_DMA is not enabled, and to allocate from the normal zone.
However, as a result of the above commit, such allocations now fail
which causes drivers to fail. These are regressions compared to the
previous kernel version."
so just revert it.
Requested-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 1 Jun 2011 20:48:50 +0000 (05:48 +0900)]
Merge git://git.infradead.org/iommu-2.6
* git://git.infradead.org/iommu-2.6:
intel-iommu: Fix off-by-one in RMRR setup
intel-iommu: Add domain check in domain_remove_one_dev_info
intel-iommu: Remove Host Bridge devices from identity mapping
intel-iommu: Use coherent DMA mask when requested
intel-iommu: Dont cache iova above 32bit
intel-iommu: Speed up processing of the identity_mapping function
intel-iommu: Check for identity mapping candidate using system dma mask
intel-iommu: Only unlink device domains from iommu
intel-iommu: Enable super page (2MiB, 1GiB, etc.) support
intel-iommu: Flush unmaps at domain_exit
intel-iommu: Remove obsolete comment from detect_intel_iommu
intel-iommu: fix VT-d PMR disable for TXT on S3 resume
Linus Torvalds [Wed, 1 Jun 2011 20:29:19 +0000 (05:29 +0900)]
block: fix mismerge of the DISK_EVENT_MEDIA_CHANGE removal
Jens' back-merge commit
698567f3fa79 ("Merge commit 'v2.6.39' into
for-2.6.40/core") was incorrectly done, and re-introduced the
DISK_EVENT_MEDIA_CHANGE lines that had been removed earlier in commits
-
9fd097b14918 ("block: unexport DISK_EVENT_MEDIA_CHANGE for
legacy/fringe drivers")
-
7eec77a1816a ("ide: unexport DISK_EVENT_MEDIA_CHANGE for ide-gd
and ide-cd")
because of conflicts with the "g->flags" updates near-by by commit
d4dc210f69bc ("block: don't block events on excl write for non-optical
devices")
As a result, we re-introduced the hanging behavior due to infinite disk
media change reports.
Tssk, tssk, people! Don't do back-merges at all, and *definitely* don't
do them to hide merge conflicts from me - especially as I'm likely
better at merging them than you are, since I do so many merges.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Metcalf [Wed, 1 Jun 2011 20:06:04 +0000 (16:06 -0400)]
tile: enable CONFIG_BUGVERBOSE
Trivial config change to enable backtraces on panic.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Stanislaw Gruszka [Wed, 1 Jun 2011 15:17:57 +0000 (17:17 +0200)]
iwl4965: correctly validate temperature value
In some cases we can read wrong temperature value. If after that
temperature value will not be updated to good one, we badly configure
tx power parameters and device is unable to send a data.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=35932
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Jun 2011 06:29:54 +0000 (08:29 +0200)]
bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
read_lock() ... read_unlock_bh() is clearly bogus.
This was broken by
commit
23691d75cdc69c3b285211b4d77746aa20a17d18
Author: Gustavo F. Padovan <padovan@profusion.mobi>
Date: Wed Apr 27 18:26:32 2011 -0300
Bluetooth: Remove l2cap_sk_list
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Halperin [Tue, 31 May 2011 18:59:30 +0000 (11:59 -0700)]
ath9k: fix two more bugs in tx power
This is the same fix as
commit
841051602e3fa18ea468fe5a177aa92b6eb44b56
Author: Matteo Croce <technoboy85@gmail.com>
Date: Fri Dec 3 02:25:08 2010 +0100
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
in two more places. I grepped the ath tree and didn't find any others.
Cc: stable@kernel.org
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Sun, 29 May 2011 12:53:20 +0000 (15:53 +0300)]
cfg80211: don't drop p2p probe responses
Commit
0a35d36 ("cfg80211: Use capability info to detect mesh beacons")
assumed that probe response with both ESS and IBSS bits cleared
means that the frame was sent by a mesh sta.
However, these capabilities are also being used in the p2p_find phase,
and the mesh-validation broke it.
Rename the WLAN_CAPABILITY_IS_MBSS macro, and verify that mesh ies
exist before assuming this frame was sent by a mesh sta.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jean Delvare [Tue, 31 May 2011 19:50:51 +0000 (15:50 -0400)]
hwmon: (coretemp) Relax target temperature range check
The current temperature range check of MSR_IA32_TEMPERATURE_TARGET
seems too strict to me, some TjMax values documented in
Documentation/hwmon/coretemp wouldn't pass. Relax the check so that
all the documented values pass.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Per Dalen [Tue, 31 May 2011 13:54:21 +0000 (06:54 -0700)]
hwmon: (max6642) Rename temp_fault sysfs attribute to temp2_fault
The temp_fault sysfs attribute is wrong, it should be temp2_fault instead.
Reported-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Dan Carpenter [Fri, 27 May 2011 06:27:16 +0000 (09:27 +0300)]
xen/blkback: potential null dereference in error handling
blkbk->pending_pages can be NULL here so I added a check for it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
[v1: Redid the loop a bit]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Laszlo Ersek [Wed, 25 May 2011 10:24:25 +0000 (12:24 +0200)]
xen/blkback: don't call vbd_size() if bd_disk is NULL
...because vbd_size() dereferences bd_disk if bd_part is NULL.
Signed-off-by: Laszlo Ersek<lersek@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Linus Torvalds [Wed, 1 Jun 2011 12:47:39 +0000 (21:47 +0900)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6:
mtd: fix physmap.h warnings
David Woodhouse [Mon, 30 May 2011 23:22:52 +0000 (00:22 +0100)]
intel-iommu: Fix off-by-one in RMRR setup
We were mapping an extra byte (and hence usually an extra page):
iommu_prepare_identity_map() expects to be given an 'end' argument which
is the last byte to be mapped; not the first byte *not* to be mapped.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Habeck [Sat, 28 May 2011 18:15:07 +0000 (13:15 -0500)]
intel-iommu: Add domain check in domain_remove_one_dev_info
The comment in domain_remove_one_dev_info() states "No need to compare
PCI domain; it has to be the same". But for the si_domain that isn't
going to be true, as it consists of all the PCI devices that are
identity mapped thus multiple PCI domains can be in si_domain. The
code needs to validate the PCI domain too.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>