OSDN Git Service
Mike Christie [Sat, 14 Jan 2006 00:05:56 +0000 (18:05 -0600)]
[SCSI] iscsi: use pageslab
From: FUJITA Tomonori <tomof@acm.org> and zhenyu.z.wang@intel.com:
We cannot handle filesystems like XFS becuase of the pages they
are sending us. We had thought page_count could be used to
work around this, but the correct test is for PageSlab.
The proper solution is to figure out what type of pages
filesystems can use so we do not have to add tests like
this or handle it in the block layer for all network block drivers
but the issue still has not been resolved on fs-devel
so we are sending this patch as a temporary fix.
This is last patch just in case it is Nakd with the explanation
that we need to push the correct fix through fs-devel, mm
or the block layer. The rest of the patchset can live without
the patch, but the driver will not work with filesystems like
XFS.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Sat, 14 Jan 2006 00:05:53 +0000 (18:05 -0600)]
[SCSI] iscsi: fix 4k stack iscsi setups
When we run the xmit code from queuecomand the stack trace
gets too deep. The patch runs the xmit code from the scsi_host
work queue. This fixes 4k stack and xfs support and should
fix the st and sg stack usage bugs.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Sat, 14 Jan 2006 00:05:50 +0000 (18:05 -0600)]
[SCSI] iscsi: seperate iscsi interface from setup functions
This is the second version of the patch to address Christoph's comments.
Instead of doing the lib, I just kept everything in scsi_trnapsort_iscsi.c
like the FC and SPI class. This was becuase the driver model and sysfs
class is tied to the session and connection setup so separating did not
buy very much at this time.
The reason for this patch was becuase HW iscsi LLDs like qla4xxx cannot
use the iscsi class becuase the scsi_host was tied to the interface and
class code. This patch just seperates the session from scsi host so
that LLDs that allocate the host per some resource like pci device
can still use the class.
This is also fixes a couple refcount bugs that can be triggered
when users have a sysfs file open, close the session, then
read or write to the file.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Sat, 14 Jan 2006 00:05:47 +0000 (18:05 -0600)]
[SCSI] iscsi: add high mem support
From Mike Christie <michaelc@cs.wisc.edu> and FUJITA Tomonori <tomof@acm.org>:
We cannot use page_address becuase some pages could be highmem.
Instead, we can use sock_no_sendpage which does kmap for us.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
FUJITA Tomonori [Sat, 14 Jan 2006 00:05:44 +0000 (18:05 -0600)]
[SCSI] iscsi: data digest page cache usage fix
Users can write to a page while we are sending it and making
digest calculations. This ends up causing us to retry the command
when a digest error is later reported. By using sock_no_sendpage
when data digests are calculated we can avoid a lot of (not all but it
helps) the retries becuase sock_no_sendpage is not zero copy.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
zhenyu.z.wang@intel.com [Sat, 14 Jan 2006 00:05:41 +0000 (18:05 -0600)]
[SCSI] iscsi: host locking fix
We should be taking the host_lock instead of the conn lock when
checking host_busy.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
zhenyu.z.wang@intel.com [Sat, 14 Jan 2006 00:05:38 +0000 (18:05 -0600)]
[SCSI] iscsi: data under/over flow fix
We need to check the ISCSI_FLAG_DATA_* flags.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
FUJITA Tomonori [Sat, 14 Jan 2006 00:05:35 +0000 (18:05 -0600)]
[SCSI] iscsi: whitespace cleanup
Remove extra whitespaces.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jes Sorensen [Wed, 11 Jan 2006 13:39:45 +0000 (08:39 -0500)]
[SCSI] sem2mutex 3w-[x9]xxx
Convert a the 3w-9xxx.c and 3w-xxxx.c drivers to use mutexes instead
of semaphores. Untested, but compiles and looks obviously correct.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Sat, 14 Jan 2006 15:28:07 +0000 (09:28 -0600)]
[SCSI] mptfc: need to select transport attrs
Now that mptfc actually uses the transport class, it can't be built
without it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moore, Eric [Fri, 13 Jan 2006 23:25:29 +0000 (16:25 -0700)]
[SCSI] fusion - fix pci express bug
The fix is to write 'MPI_HIM_DIM' to the Host Interrupt Mask
register, when enabling interrupts. Instead of the
tilde of MPI_HIM_RIM.
Apparently writing '1's to some of the reserved bits was causing
all the bits to go to `1`, which effectly disabled all interrupts.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moore, Eric [Fri, 13 Jan 2006 23:33:59 +0000 (16:33 -0700)]
[SCSI] scsi_transport_sas: mapping the rphy channel equal to the port identifier
We will be mapping the RAID volumes in mptsas to a reserved
channel that
is one larger than the anticapated number of ports on the direct
attached host
adapter.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moore, Eric [Fri, 13 Jan 2006 23:25:23 +0000 (16:25 -0700)]
[SCSI] fusion - mpi header udpate
This updates mpi headers in fusion drivers to version 1.5.12.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moore, Eric [Fri, 13 Jan 2006 23:25:20 +0000 (16:25 -0700)]
[SCSI] fusion - adding raid support in mptsas
The SAS RAID volumes are reported beyond the expected number of phys.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Christoph Hellwig [Fri, 13 Jan 2006 18:04:00 +0000 (19:04 +0100)]
[SCSI] remove target parent limitiation
When James Smart fixed the issue of the userspace scan atributes
crashing the system with the FC transport class he added a patch to
let the transport class check if the parent is valid for a given
transport class.
When adding support for the integrated raid of fusion sas devices
we ran into a problem with that, as it didn't allow adding virtual
raid volumes without the transport class knowing about it.
So this patch adds a user_scan attribute instead, that takes over from
scsi_scan_host_selected if the transport class sets it and thus lets
the transport class control the user-initiated scanning. As this
plugs the hole about user-initiated scanning the target_parent hook
goes away and we rely on callers of the scanning routines to do
something sensible.
For SAS this meant I had to switch from a spinlock to a mutex to
synchronize the topology linked lists, in FC they were completely
unsynchronized which seems wrong.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moore, Eric [Fri, 13 Jan 2006 23:25:26 +0000 (16:25 -0700)]
[SCSI] fusion - adding support for FC949ES
Add software recognition for the new LSI Logic Fibre Channel controller.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Michael Reed [Fri, 13 Jan 2006 20:31:54 +0000 (14:31 -0600)]
[SCSI] mptfusion - fc transport attributes
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jes Sorensen [Sat, 14 Jan 2006 00:05:44 +0000 (16:05 -0800)]
[SCSI] sem2mutex: scsi_transport_spi.c
Convert the SCSI transport class code to use a mutex rather than a
semaphore.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Fri, 13 Jan 2006 21:36:25 +0000 (15:36 -0600)]
[SCSI] fix up message/i2o/pci.c
There was a use before initialisation of c->name
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Christoph Hellwig [Fri, 13 Jan 2006 17:27:50 +0000 (18:27 +0100)]
[SCSI] fusion: kzalloc / kcalloc conversion
Convert kmalloc + memset to kzalloc or kcalloc in fusion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Christoph Hellwig [Fri, 13 Jan 2006 17:27:11 +0000 (18:27 +0100)]
[SCSI] fusion: convert semaphores to mutexes
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Christoph Hellwig [Fri, 13 Jan 2006 17:04:41 +0000 (18:04 +0100)]
[SCSI] mptsas: support basic hotplug
Adds hotplug support for SAS end devices. Unfortunately the fusion
firmware doesn't generate similar events for expanders addition/removal
so we can't support them yet. Eric has an idea about a clever scheme to
find out about expander changes so that'll be added later on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark [Thu, 12 Jan 2006 13:31:57 +0000 (08:31 -0500)]
[SCSI] I2O: move pci_request_regions() just behind pci_enable_device()
The problem in dpt_i2o could be the pci config space accesses it
triggers as it loads, dangerous to do if there is any I/O activity going
on in the other driver (probable if a boot driver I guess).
I approve this patch to dpt_i2o.c, and am applying it to the Adaptec
branch of the driver.
Thanks for the investigation Ryoji.
---
In linux 2.6.15, data transfer does hang when both dpt_i2o
and i2o_block drivers are loaded.
It seems that location of pci_request_regions() are wrong.
I moved it just behind pci_enable_device() like other drivers,
and it becomes fine.
Signed-off-by: Ryoji Kamei <kamei@miraclelinux.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jack Hammer [Fri, 13 Jan 2006 15:06:50 +0000 (10:06 -0500)]
[SCSI] ips: Mode Sense (Caching Page ) fix
To avoid the "sda: got wrong page" message, the ServeRAID driver
should be setting flags indicating that the Mode Sense commands are
not supported.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Andreas Herrmann [Fri, 13 Jan 2006 01:26:11 +0000 (02:26 +0100)]
[SCSI] zfcp: transport class adaptations II
Replaced zfcp adapter attributes with fc_host attributes:
fc_topology by port_type, physical_wwpn by permanent_port_name.
Make use of fc_host attribute supported_speeds.
Removed zfcp adapter attribute physical_s_id.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Andreas Herrmann [Thu, 5 Jan 2006 08:59:34 +0000 (09:59 +0100)]
[SCSI] zfcp: transport class adaptations
Added host stats, removed superfluous get_starget_ functions,
removed some attributes from zfcp specific sysfs tree (e.g.
scsi_host_no, scsi_lun, wwnn and d_id).
Host stats are given for the physical adapter port not for the
virtual adapter. Reset stats is implemented in the device driver.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Maxim Shchetynin [Thu, 5 Jan 2006 08:56:47 +0000 (09:56 +0100)]
[SCSI] zfcp: handle unsolicited status notification lost
Handle unsolicited adapter status that informs about loss of
previous unsolicited status notification(s).
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Andreas Herrmann [Fri, 13 Jan 2006 01:16:54 +0000 (02:16 +0100)]
[SCSI] fc transport: add permanent_port_name fc_host attribute
Add fc_host attribute permanent_port_name which is
used to show the port name of the primary port -
the port that initially logged into the fabric.
For a virtual port (registered via the primary port with
FDISC command) it is useful to know not only its (virtual)
port name but also the permanent port name.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Christoph Hellwig [Wed, 11 Jan 2006 13:28:06 +0000 (14:28 +0100)]
[SCSI] sr: split sr_audio_ioctl into specific helpers
split each ioctl handled in sr_audio_ioctl into a function of it's own.
This cleans the code up nicely, and allows various places in sr_ioctl
to call these helpers directly instead of going through the multiplexer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Christoph Hellwig [Fri, 6 Jan 2006 17:34:07 +0000 (18:34 +0100)]
[SCSI] always handle REQ_BLOCK_PC requests in common code
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just
fine in the core code. There is a small behaviour change in that some
check in sr's rw_intr are bypassed, but I consider the old behaviour
a bug.
Mike found this cleanup opportunity and provdided early patches, so all
the credit goes to him, even if I redid the patches from scratch beause
that was easier than forward-porting the old patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Christoph Hellwig [Wed, 4 Jan 2006 12:45:20 +0000 (13:45 +0100)]
[SCSI] sas: fix removal of devices behind expanders
We need to iterate over all children when removing and expander, else
stale objects will be around after host removal. This fixes the oops
Eric Moore saw when removing and reloading mptsas.
Also don't try the scsi_remove_target call unless operating on an end
device. The current unconditional call is harmless but confusing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Petr Vandrovec [Wed, 11 Jan 2006 19:31:07 +0000 (11:31 -0800)]
[SCSI] Pass proper device from BusLogic to SCSI layer
While trying to get SUSE's SLES9 working on system with more than 4GB we've
noticed that SCSI layer happilly passes addresses over 4GB to the buslogic
driver, which is quite a big problem as buslogic can generate only 32bit
busmastering cycles.
Fortunately in the current kernels this problem does not exist anymore as
SCSI layer now assumes 4GB capable device by default, but it is still good
idea to pass correct device structure to the SCSI layer. If nothing else,
/sys/block/sda/device now points to
/sys/devices/pci0000:00/0000:00:10.0/host0/... instead of
/sys/devices/platform/host0/... like it did in the past.
Change does nothing for ISA based BusLogic adapters, they'll still end
under platform (and they are probably broken for long time as I do not see
anything forcing ISA 16MB limit for them).
Signed-off-by: Petr Vandrovec <petr@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Thu, 12 Jan 2006 18:07:13 +0000 (12:07 -0600)]
[SCSI] aic79xx: bump version to 3.0
This takes us past the old 1.x version of the SCSI driver and the 2.x
version of the aic website version to reflect the full incorporation
of both branches.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hannes Reinecke [Thu, 12 Jan 2006 11:08:06 +0000 (12:08 +0100)]
[SCSI] aic79xx: Sequencer update
Update sequencer code to Adaptec version 2.0.12-6.3.9.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hannes Reinecke [Thu, 12 Jan 2006 11:07:02 +0000 (12:07 +0100)]
[SCSI] aic79xx: Sanitize inb/outb handling
This patch coalesces inb/outb calls to the approriate word or long form.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hannes Reinecke [Thu, 12 Jan 2006 11:05:46 +0000 (12:05 +0100)]
[SCSI] aic79xx: Use struct map_node
Use struct map_node instead of separate variables.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hannes Reinecke [Thu, 12 Jan 2006 11:04:28 +0000 (12:04 +0100)]
[SCSI] aic7xxx/aic79xx: New device ids
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Chuck Ebbert [Thu, 12 Jan 2006 04:58:40 +0000 (23:58 -0500)]
[SCSI] Mask capabilities for SCSI-1 CD drive
SCSI-1 CD drives can't do MRW or be opened for writing, so mask off
those capabilities.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 11 Jan 2006 17:28:57 +0000 (09:28 -0800)]
[SCSI] aacraid: README update
Received From Mark Salyzyn.
Move the README from the driver directory to the Documentation directory.
Updated the documentation, added descriptions for cards that
were missing.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 11 Jan 2006 17:28:29 +0000 (09:28 -0800)]
[SCSI] aacraid: 17 element sg performance update
Received From Mark Salyzyn.
The Jaguar and Corsair class of adapters (2410, 2810, 2610, 21610, CERC)
perform better (about 10% better read performance, write performance
neutral) with current Firmware if the OS limits the number of scatter
gather elements to 17 per request.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 11 Jan 2006 17:28:16 +0000 (09:28 -0800)]
[SCSI] aacraid: better sysfs adapter information
Received from Mark Salyzyn.
Provide more accurate adapter information.
Allows the Adapter Firmware to override the Adapter product
information.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 11 Jan 2006 17:28:07 +0000 (09:28 -0800)]
[SCSI] aacraid: Fix default FIB size
Received from Mark Salyzyn.
If the adapter has not instructed us otherwise that it can handle a
'large' FIB, then it can handle at most a 2KB FIB.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Christoph Hellwig [Wed, 11 Jan 2006 13:20:43 +0000 (14:20 +0100)]
[SCSI] sas: clear parent->rphy in sas_rphy_delete
We need to clear the backpointer on rphy removal, else we'll run into
problems with host removal after a device has been hot unplugged.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Arjan van de Ven [Wed, 11 Jan 2006 12:16:10 +0000 (13:16 +0100)]
[SCSI] turn most scsi semaphores into mutexes
the scsi layer is using semaphores in a mutex way, this patch converts
these into using mutexes instead
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Tue, 10 Jan 2006 18:11:42 +0000 (12:11 -0600)]
[SCSI] aic7xxx: fix timer handling bug
The driver is doing a rather stupid mod_timer allegedly to "give
request sense more time to complete". This is illegal and pointless,
so just eliminate it. Also eliminate all the other uses of struct
timer_list in the driver, which are mostly bogus.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Andrew Vasquez [Mon, 9 Jan 2006 18:17:40 +0000 (10:17 -0800)]
[SCSI] qla2xxx: Kconfig: two fixes
Original From: Adrian Bunk
Here's a composite patch with Adrian's original additions and
help-text with the new Kconfig variable SCSI_QLA_FC.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adrian Bunk [Fri, 6 Jan 2006 19:21:28 +0000 (20:21 +0100)]
[SCSI] lpfc_scsi.c: make lpfc_get_scsi_buf() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adrian Bunk [Thu, 5 Jan 2006 22:39:18 +0000 (23:39 +0100)]
[SCSI] scsi_transport_spi.c: make print_nego() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moore, Eric [Wed, 4 Jan 2006 21:58:43 +0000 (14:58 -0700)]
[SCSI] raid_class.c - adding RAID10 and RAID10 defines
Adding defines for RAID10 and RAID50 levels, in preparation
of adding RAID Transport support in the mpt fusion drivers.
(BTW: IME is RAID10, and IM is RAID1).
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Linus Torvalds [Thu, 12 Jan 2006 03:36:32 +0000 (19:36 -0800)]
Merge /pub/scm/linux/kernel/git/mchehab/v4l-dvb
Vivek Goyal [Thu, 12 Jan 2006 02:35:20 +0000 (03:35 +0100)]
[PATCH] x86_64: Fix SMP bootup with CONFIG_KDUMP enabled
o This fix was posted for i386 long back. Posting it for x86_64.
http://marc.theaimsgroup.com/?l=linux-kernel&m=
110380103229830&w=2
o This patch fixes the problem of secondary cpus boot up. This situation
is faced when kernel is built for default locations like 16MB and
onwards. In this configuration, only primary cpu (BP) comes and
secondary cpus don't boot.
o Problem occurs because in trampoline code, lgdt is not able to load the
GDT as it happens to be situated beyond 16MB. This is due to the fact
that cpu is still in real mode and default operand size is 16bit.
o This patch uses lgdtl instead of lgdt to force operand size to 32
instead of 16.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:47:10 +0000 (22:47 +0100)]
[PATCH] x86_64: Don't confuse noapic with noapictimer
Handling common prefixes is tricky.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan Beulich [Wed, 11 Jan 2006 21:47:07 +0000 (22:47 +0100)]
[PATCH] x86_64: don't copy command line twice
... reducing the amount of changes Xen has to do.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan Beulich [Wed, 11 Jan 2006 21:47:03 +0000 (22:47 +0100)]
[PATCH] i386/x86-64: make setup_early_printk() usage consistent
The explicit and implicit calls to setup_early_printk() were passing
inconsistent arguments.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:47:00 +0000 (22:47 +0100)]
[PATCH] i386: Move DOUBLEFAULT config to arch/i386/Kconfig
It has no business being elsewhere and x86-64 doesn't need/want it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:46:57 +0000 (22:46 +0100)]
[PATCH] x86_64: Allow kernel page tables upto the end of memory
Previously they would be only allocated before the kernel text at
1MB. This limited the maximum supported memory to 128GB.
Now allow the e820 allocator to put them everywhere. Try
to put them beyond any DMA zones to avoid filling them up.
This should free some GFP_DMA memory compared to earlier kernels.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:46:54 +0000 (22:46 +0100)]
[PATCH] x86_64: Use safe_smp_processor_id in MCE handler
hard_smp_processor_id would return the local APIC id instead
of the Linux processor id. On big systems they are often
not identical. safe_smp_processor_id is just a wrapper
around it that does the necessary conversions.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:46:51 +0000 (22:46 +0100)]
[PATCH] x86_64: Some housekeeping in local APIC code
Remove support for obsolete hardware and cleanup.
- Remove checks for non integrated APICs
- Replace apic_write_around with apic_write.
- Remove apic_read_around
- Remove APIC version reads used by old workarounds
- Remove old workaround for Simics
- Fix indentation
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan Beulich [Wed, 11 Jan 2006 21:46:48 +0000 (22:46 +0100)]
[PATCH] x86_64: Display meaningful part of filename during BUG()
When building in a separate objtree, file names produced by BUG() & Co. can
get fairly long; printing only the first 50 characters may thus result in
(almost) no useful information. The following change makes it so that rather
the last 50 characters of the filename get printed.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan Beulich [Wed, 11 Jan 2006 21:46:45 +0000 (22:46 +0100)]
[PATCH] x86_64: Reduce screen space needed by stack trace
Especially under Xen, where the console cannot be adjusted to more than 25
lines, it is fairly important that the information displayed during a panic
is as compact as possible. Below adjustments work towards that.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan Beulich [Wed, 11 Jan 2006 21:46:42 +0000 (22:46 +0100)]
[PATCH] x86_64: Fix get_cmos_time()
Due to a broken condition, the body of the loop that is intended to wait for
the Update-In-Progress bit to get set and then cleared again was never
entered; in fact, the entire loop was optimized out by the compiler. Here is
a change to fix the condition (and to also move the initialization of locals
out of the spin lock protected region).
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:46:39 +0000 (22:46 +0100)]
[PATCH] x86_64: No need to export get_cmos_time anymore
It was only needed for APM
Pointed out by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:46:36 +0000 (22:46 +0100)]
[PATCH] x86_64: Remove unused AMD K8 C stepping flag
X86_FEATURE_K8_C was a synthetic Linux CPUID flag that was used for some
code optimizations in Opteron C stepping or later. But support for pre C
stepping optimizations has been removed, so this isn't needed anymore.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:46:33 +0000 (22:46 +0100)]
[PATCH] i386: Move phys_proc_id/early intel workaround to correct function.
early_cpu_detect only runs on the BP, but this code needs to run
on all CPUs.
Looks like a mismerge somewhere. Also add a warning comment.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stephen Hemminger [Wed, 11 Jan 2006 21:46:30 +0000 (22:46 +0100)]
[PATCH] x86_64: sparse warning cleanups
Fix some trivial sparse warnings in x86_64 code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:46:27 +0000 (22:46 +0100)]
[PATCH] x86_64: Move NUMA page_to_pfn/pfn_to_page functions out of line
Saves about ~18K .text in defconfig
There would be more optimization potential, but that's for later.
Suggestion originally from Bill Irwin.
Fix from Andy Whitcroft.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:46:24 +0000 (22:46 +0100)]
[PATCH] x86_64: Remove unused segments
They used to be used by the reboot code, but not anymore.
Noticed by Jan Beulich
Cc: JBeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Vivek Goyal [Wed, 11 Jan 2006 21:46:21 +0000 (22:46 +0100)]
[PATCH] x86_64: ioapic virtual wire mode fix
o Currently, during kexec reboot, IOAPIC is re-programmed back to virtual
wire mode if there was an i8259 connected to it. This enables getting
timer interrupts in second kernel in legacy mode.
o After putting into virtual wire mode, IOAPIC delivers the i8259 interrupts
to CPU0. This works well for kexec but not for kdump as we might crash
on a different CPU and second kernel will not see timer interrupts.
o This patch modifies the redirection table entry to deliver the timer
interrupts to the cpu we are rebooting (instead of hardcoding to zero).
This ensures that second kernel receives timer interrupts even on a
non-boot cpu.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ravikiran G Thirumalai [Wed, 11 Jan 2006 21:46:18 +0000 (22:46 +0100)]
[PATCH] x86_64: Inclusion of ScaleMP vSMP architecture patches - vsmp_arch
Introduce vSMP arch to the kernel.
This patch:
1. Adds CONFIG_X86_VSMP
2. Adds machine specific macros for local_irq_disabled, local_irq_enabled
and irqs_disabled
3. Writes to the vSMP CTL device to indicate kernel compiled with CONFIG_VSMP
Signed-off-by: Ravikiran Thirumalai <kiran@scalemp.com>
Signed-off-by: Shai Fultheim <shai@scalemp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ravikiran G Thirumalai [Wed, 11 Jan 2006 21:46:15 +0000 (22:46 +0100)]
[PATCH] x86_64: Inclusion of ScaleMP vSMP architecture patches - vsmp_align
vSMP specific alignment patch to
1. Define INTERNODE_CACHE_SHIFT for vSMP
2. Use this for alignment of critical structures
3. Use INTERNODE_CACHE_SHIFT for ARCH_MIN_TASKALIGN,
and let the slab align task_struct allocations to the internode cacheline size
4. Introduce and use ARCH_MIN_MMSTRUCT_ALIGN for mm_struct slab allocations.
Signed-off-by: Ravikiran Thirumalai <kiran@scalemp.com>
Signed-off-by: Shai Fultheim <shai@scalemp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:46:12 +0000 (22:46 +0100)]
[PATCH] x86_64: Make sure BITS_PER_ATOMIC is defined in asm-generic/atomic.h
Fixes
CC fs/nfsctl.o
In file included from include2/asm/atomic.h:427,
from /home/lsrc/quilt/linux/include/linux/file.h:8,
from /home/lsrc/quilt/linux/fs/nfsctl.c:8:
/home/lsrc/quilt/linux/include/asm-generic/atomic.h:20:5: warning: "BITS_PER_LONG" is not defined
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brian Gerst [Wed, 11 Jan 2006 21:46:09 +0000 (22:46 +0100)]
[PATCH] x86_64: cleanup enter_lazy_tlb()
Move the #ifdef into the function body.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eric W. Biederman [Wed, 11 Jan 2006 21:46:06 +0000 (22:46 +0100)]
[PATCH] x86_64: Memorize location of i8259 for reboots.
Currently we attempt to restore virtual wire mode on reboot, which only
works if we can figure out where the i8259 is connected. This is very
useful when we are kexec another kernel and likely helpful to an peculiar
BIOS that make assumptions about how the system is setup.
Since the acpi MADT table does not provide the location where the i8259 is
connected we have to look at the hardware to figure it out.
Most systems have the i8259 connected the local apic of the cpu so won't be
affected but people running Opteron and some serverworks chipsets should be
able to use kexec now.
In addition this patch removes the hard coded assumption that the io_apic
that delivers isa interrups is always known to the kernel as io_apic 0.
There does not appear to be anything to guarantee that assumption is true.
And From: Vivek Goyal <vgoyal@in.ibm.com>
A minor fix to the patch which remembers the location of where i8259 is
connected. Now counter i has been replaced by apic. counter i is having
some junk value which was leading to non-detection of i8259 connected to
IOAPIC.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chuck Ebbert [Wed, 11 Jan 2006 21:46:03 +0000 (22:46 +0100)]
[PATCH] x86_64: allow setting RF in EFLAGS
Setting RF (resume flag) allows a debugger to resume execution after a code
breakpoint without tripping the breakpoint again. It is reset by the CPU
after executing one instruction.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chuck Ebbert [Wed, 11 Jan 2006 21:46:00 +0000 (22:46 +0100)]
[PATCH] x86_64: "invalid operand" -> "invalid opcode"
The manual says Int 6 is "invalid opcode", not "invalid operand".
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Luiz Fernando Capitulino [Wed, 11 Jan 2006 21:45:57 +0000 (22:45 +0100)]
[PATCH] x86_64: Sparse warnings fix.
Fixes the following sparse warnings:
arch/x86_64/kernel/mce_amd.c:321:29: warning: Using plain integer as NULL pointer
arch/x86_64/kernel/mce_amd.c:410:41: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:54 +0000 (22:45 +0100)]
[PATCH] x86_64: Remove useless KDB vector
It was set as an NMI, but the NMI bit always forces an interrupt
to end up at vector 2. So it was never used. Remove.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jason Uhlenkott [Wed, 11 Jan 2006 21:45:51 +0000 (22:45 +0100)]
[PATCH] x86_64: Don't claim too many vectors for TLB flushing
It looks like the new scalable TLB flush code for x86_64 is claiming
one more IRQ vector than it actually uses.
Signed-off-by: Jason Uhlenkott <jasonuhl@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:48 +0000 (22:45 +0100)]
[PATCH] x86_64: Tell user to enable GART_IOMMU when needed
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:45 +0000 (22:45 +0100)]
[PATCH] x86_64: Fix warning in nmi.c on uniprocessor kernels
Fix
CC arch/x86_64/kernel/nmi.o
linux/arch/x86_64/kernel/nmi.c: In function ???check_nmi_watchdog???:
linux/arch/x86_64/kernel/nmi.c:155: warning: statement with no effect
on Uniprocessor builds.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ravikiran G Thirumalai [Wed, 11 Jan 2006 21:45:42 +0000 (22:45 +0100)]
[PATCH] x86_64: Allocate PDAs in the local node
Patch uses a static PDA array early at boot and reallocates processor PDA
with node local memory when kmalloc is ready, just before pda_init.
The boot_cpu_pda is needed since the cpu_pda is used even before pda_init for
that cpu is called (to set the static per-cpu areas offset table etc)
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ravikiran G Thirumalai [Wed, 11 Jan 2006 21:45:39 +0000 (22:45 +0100)]
[PATCH] x86_64: Node local pda take 2 -- cpu_pda preparation
Helper patch to change cpu_pda users to use macros to access cpu_pda
instead of the cpu_pda[] array.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ravikiran Thirumalai [Wed, 11 Jan 2006 21:45:36 +0000 (22:45 +0100)]
[PATCH] x86_64: Early initialization of cpu_to_node
Patch enables early intialization of cpu_to_node.
apicid_to_node is built by reading the SRAT table, from acpi_numa_init with
ACPI_NUMA and k8_scan_nodes with K8_NUMA.
x86_cpu_to_apicid is built by parsing the ACPI MADT table, from acpi_boot_init.
We combine these two tables and setup cpu_to_node.
Early intialization helps the static per_cpu_areas in getting pages from
correct node.
Change since last release:
Do not initialize early init_cpu_to_node for faking node cases.
Patch tested on TYAN dual core 4P board with K8 only, ACPI_NUMA.
Tested on EM64T NUMA. Also tested with numa=off, numa=fake, and running
a kernel compiled with NUMA on a regular EM64 2 way SMP.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:33 +0000 (22:45 +0100)]
[PATCH] x86_64: Fix up white space in time.c
No functional changes.
And remove one redundant prototype.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:30 +0000 (22:45 +0100)]
[PATCH] x86_64: Use standard __always_inline in vsyscall.c
Replacing the old home brewn __force_inline.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:27 +0000 (22:45 +0100)]
[PATCH] i386: Replace broken serialize_cpu in microcode driver with correct sync_core
Passing random input values in eax to cpuid is not a good idea
because the CPU will GPF for unknown ones.
Use the correct x86-64 version that exists for a longer time too.
This also adds a memory barrier to prevent the optimizer from
reordering.
Cc: tigran@veritas.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:24 +0000 (22:45 +0100)]
[PATCH] x86_64: On Intel CPUs don't do an additional CPU sync before RDTSC
RDTSC serialization using cpuid is not needed for Intel platforms.
This increases gettimeofday performance.
Cc: vojtech@suse.cz
Cc: rohit.seth@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:21 +0000 (22:45 +0100)]
[PATCH] x86_64: Support alternative() in vsyscalls
The real vsyscall .text addresses are not mapped when the alternative()
replacement runs early, so use some black magic to access them using
the direct mapping.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:18 +0000 (22:45 +0100)]
[PATCH] x86_64: Support alternative() with a output argument.
Needed for follow on patches
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:15 +0000 (22:45 +0100)]
[PATCH] x86_64: Don't try to synchronize the TSC over CPUs on Intel CPUs at boot.
They already do this in hardware and the Linux algorithm
actually adds errors.
Cc: mingo@elte.hu
Cc: rohit.seth@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:12 +0000 (22:45 +0100)]
[PATCH] x86_64: Fix compile error with !CONFIG_COMPAT
cpumask.h wasn't included implicitely into proto.h in this case.
Just move it over to smp.h
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Vivek Goyal [Wed, 11 Jan 2006 21:45:09 +0000 (22:45 +0100)]
[PATCH] x86_64: x86_64 write apic id fix
o Apic id is in most significant 8 bits of APIC_ID register. Current code
is trying to write apic id to least significant 8 bits. This patch fixes
it.
o This fix enables booting uni kdump capture kernel on a cpu with non-zero
apic id.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brian Gerst [Wed, 11 Jan 2006 21:45:06 +0000 (22:45 +0100)]
[PATCH] x86_64: Remove duplicate exports
Remove exports that are already exported from the object's source file.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brian Gerst [Wed, 11 Jan 2006 21:45:03 +0000 (22:45 +0100)]
[PATCH] x86_64: unexport pci_*_consistent
These functions are inlines and shouldn't be exported.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:45:00 +0000 (22:45 +0100)]
[PATCH] x86_64: Remove unused apic_write_atomic
This function is never used for x86_64.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:44:57 +0000 (22:44 +0100)]
[PATCH] x86_64: Make the cpu_*_maps in kernel/sched.c read mostly
They are referred to often so avoid potential false sharing for them.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:44:54 +0000 (22:44 +0100)]
[PATCH] i386: make pci_map_single/pci_map_sg warn for zero length.
As suggested by Linus.
This catches driver bugs that could cause corruption on IOMMU architectures.
Also I converted the BUGs to out_of_line_bug()s to save a bit
of text space.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:44:51 +0000 (22:44 +0100)]
[PATCH] x86_64: Enable sound in old style OSS driver for NForce4 CK804
Just add the missing PCI ID.
Cc: perex@suse.cz
Cc: tiwai@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:44:48 +0000 (22:44 +0100)]
[PATCH] x86_64: Make it clear in machine checks that it's an hardware problem
Hopefully the users will take the hint.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen [Wed, 11 Jan 2006 21:44:45 +0000 (22:44 +0100)]
[PATCH] x86_64: Clean up copy_*_user
- Remove optimization for old B stepping Opteron
- Make the fast path for copies with a multiple of eight length faster.
- Minor instruction rearrangement to hopefully avoid a pipeline
stall or two.
- Add comment about errata to consider.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>