OSDN Git Service
Vadim Pasternak [Tue, 20 Nov 2018 06:52:03 +0000 (06:52 +0000)]
mlxsw: core: Extend cooling device with cooling levels
Extend cooling device with cooling levels vector to allow more
flexibility of PWM setting.
Thermal zone algorithm operates with the numerical states for PWM
setting. Each state is the index, defined in range from 0 to 10 and it's
mapped to the relevant duty cycle value, which is written to PWM
controller. With the current definition fan speed is set to 0% for state
0, 10% for state 1, and so on up to 100% for the maximum state 10.
Some systems have limitation for the PWM speed minimum. For such systems
PWM setting speed to 0% will just disable the ability to increase speed
anymore and such device will be stall on zero speed. Cooling levels
allow to configure state vector according to the particular system
requirements. For example, if PWM speed is not allowed to be below 30%,
cooling levels could be configured as 30%, 30%, 30%, 30%, 40%, 50% and
so on.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun Vynipadath [Tue, 20 Nov 2018 06:41:39 +0000 (12:11 +0530)]
cxgb4/cxgb4vf: Fix mac_hlist initialization and free
Null pointer dereference seen when cxgb4vf driver is unloaded
without bringing up any interfaces, moving mac_hlist initialization
to driver probe and free the mac_hlist in remove to fix the issue.
Fixes:
24357e06ba51 ("cxgb4vf: fix memleak in mac_hlist initialization")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 20 Nov 2018 01:45:55 +0000 (17:45 -0800)]
tcp: drop dst in tcp_add_backlog()
Under stress, softirq rx handler often hits a socket owned by the user,
and has to queue the packet into socket backlog.
When this happens, skb dst refcount is taken before we escape rcu
protected region. This is done from __sk_add_backlog() calling
skb_dst_force().
Consumer will have to perform the opposite costly operation.
AFAIK nothing in tcp stack requests the dst after skb was stored
in the backlog. If this was the case, we would have had failures
already since skb_dst_force() can end up clearing skb dst anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Nov 2018 18:15:36 +0000 (10:15 -0800)]
ipv4: Don't try to print ASCII of link level header in martian dumps.
This has no value whatsoever.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 20 Nov 2018 01:30:19 +0000 (17:30 -0800)]
net_sched: sch_fq: avoid calling ktime_get_ns() if not needed
There are two cases were we can avoid calling ktime_get_ns() :
1) Queue is empty.
2) Internal queue is not empty.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Nov 2018 02:53:46 +0000 (18:53 -0800)]
Merge branch 'gred-add-offload-support'
Jakub Kicinski says:
====================
gred: add offload support
This series adds support for GRED offload in the nfp driver. So
far we have only supported the RED Qdisc offload, but we need a
way to differentiate traffic types e.g. based on DSCP marking.
It may seem like PRIO+RED is a good match for this job, however,
(a) we don't need strict priority behaviour of PRIO, and (b) PRIO
uses the legacy way of mapping ToS fields to bands, which is quite
awkward and limitting.
The less commonly used GRED Qdisc is a better much for the scenario,
it allows multiple sets of RED parameters and queue lengths to be
maintained with a single FIFO queue. This is exactly how nfp offload
behaves. We use a trivial u32 classifier to assign packets to virtual
queues.
There is also the minor advantage that GRED can't have its child
changed, therefore limitting ways in which the configuration of SW
path can diverge from HW offload.
Last patch of the series adds support for (G)RED in non-ECN mode,
where packets are dropped instead of marked.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:50 +0000 (15:21 -0800)]
nfp: abm: add support for more threshold actions
Original FW only allowed us to perform ECN marking. Newer releases
also support plain old drop. Add the ability to configure drop
policy. This is particularly useful in combination with GRED,
because different bands can have different ECN marking setting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:49 +0000 (15:21 -0800)]
nfp: abm: add cls_u32 offload for simple band classification
Use offload of very simple u32 filters to direct packets to GRED
bands based on the DSCP marking. No u32 hashing is supported,
just plain simple filters matching on ToS or Priority with
appropriate mask device can support.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:48 +0000 (15:21 -0800)]
nfp: abm: add functions to update DSCP -> virtual queue map
Learn how to set the DSCP map. FW uses a packed array which
geometry depends on the number of supported priorities and
virtual queues. Write code to assemble this map and to communicate
the setting to the FW via mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:47 +0000 (15:21 -0800)]
nfp: abm: calculate PRIO map len and check mailbox size
In preparation for PRIO offload calculate how long the prio map
for FW will be and make sure the configuration can be performed
via the vNIC mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:46 +0000 (15:21 -0800)]
net: sched: cls_u32: add res to offload information
In case of egress offloads the class/flowid assigned by the filter
may be very important for offloaded Qdisc selection. Provide this
info to drivers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:45 +0000 (15:21 -0800)]
nfp: abm: add GRED offload
Add support for GRED offload. It behaves much like RED, but
can apply different parameters to different bands. GRED operates
pretty much exactly like our HW/FW with a single FIFO and different
RED state instances.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:44 +0000 (15:21 -0800)]
nfp: abm: wrap RED parameters in bands
Wrap RED parameters and stats into a structure, and a 1-element
array. Upcoming GRED offload will add the support for more bands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:43 +0000 (15:21 -0800)]
net: sched: gred: support reporting stats from offloads
Allow drivers which offload GRED to report back statistics. Since
A lot of GRED stats is fairly ad hoc in nature pass to drivers the
standard struct gnet_stats_basic/gnet_stats_queue pairs, and
untangle the values in the core.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:42 +0000 (15:21 -0800)]
net: sched: gred: add basic Qdisc offload
Add basic offload for the GRED Qdisc. Inform the drivers any
time Qdisc or virtual queue configuration changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:41 +0000 (15:21 -0800)]
nfp: abm: add up bands for sto/non-sto stats
Add up stats for all bands for the extra ethtool statistics.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:40 +0000 (15:21 -0800)]
nfp: abm: switch to extended stats for reading packet/byte counts
In PRIO-enabled FW read the statistics from per-band symbol, rather
than from the standard per-PCIe-queue counters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:39 +0000 (15:21 -0800)]
nfp: abm: size threshold table to account for bands
Make sure the threshold table is large enough to hold information
for all bands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:38 +0000 (15:21 -0800)]
nfp: abm: pass band parameter to functions
In preparation for per-band RED offload pass band parameter to
functions. For now it will always be 0.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 19 Nov 2018 23:21:37 +0000 (15:21 -0800)]
nfp: abm: map per-band symbols
In preparation for multi-band RED offload if FW is capable map
the extended symbols which will allow us to set per-band parameters
and read stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 19 Nov 2018 13:02:15 +0000 (21:02 +0800)]
net: hns3: add common validation in hclge_dcb
Before setting tm related configuration to hardware, driver
needs to check the configuration provided by user is valid.
Currently hclge_ieee_setets and hclge_setup_tc both implement
their own checking, which has a lot in common.
This patch addes hclge_dcb_common_validate to do the common
checking. The checking in hclge_tm_prio_tc_info_update
and hclge_tm_schd_info_update is unnecessary now, so change
the return type to void, which removes the need to do error
handling when one of the checking fails.
Also, ets->prio_tc is indexed by user prio and ets->tc_tsa is
indexed by tc num, so this patch changes them to use different
index.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Nov 2018 01:59:45 +0000 (17:59 -0800)]
Merge branch 'selftests-Add-tests-for-VXLAN-at-an-802-1d-bridge'
Ido Schimmel says:
====================
selftests: Add tests for VXLAN at an 802.1d bridge
Petr says:
This patchset adds several tests for VXLAN attached to an 802.1d bridge
and fixes a related bug.
First patch #1 fixes a bug in propagating SKB already-forwarded marks
over veth to bridges, where they are irrelevant. This bug causes the
vxlan_bridge_1d test suite from this patchset to fail as the packets
aren't forwarded by br2.
In patches #2 and #3, lib.sh is extended to support network namespaces.
The use of namespaces is necessitated by VXLAN, which allows only one
VXLAN device with a given VNI per namespace. Thus to host full topology
on a single box for selftests, the "remote" endpoints need to be in
namespaces.
In patches #4-#6, lib.sh is extended in other ways to facilitate the
following patches.
In patches #7-#15, first the skeleton, and later the generic tests
themselves are added.
Patch #16 then adds another test that serves as a wrapper around the
previous one, and runs it with a non-default port number.
Patches #17 and #18 add mlxsw-specific tests. About those, Ido writes:
The first test creates various configurations with regards to the VxLAN
and bridge devices and makes sure the driver correctly forbids
unsupported configuration and permits supported ones. It also verifies
that the driver correctly sets the offload indication on FDB entries and
the local route used for VxLAN decapsulation.
The second test verifies that the driver correctly configures the singly
linked list used to flood BUM traffic and that traffic is flooded as
expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 19 Nov 2018 16:11:27 +0000 (16:11 +0000)]
selftests: mlxsw: Add a test for VxLAN flooding
The device stores flood records in a singly linked list where each
record stores up to three IPv4 addresses of remote VTEPs. The test
verifies that packets are correctly flooded in various cases such as
deletion of a record in the middle of the list.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 19 Nov 2018 16:11:26 +0000 (16:11 +0000)]
selftests: mlxsw: Add a test for VxLAN configuration
Test various aspects of VxLAN offloading which are specific to mlxsw,
such as sanitization of invalid configurations and offload indication.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:25 +0000 (16:11 +0000)]
selftests: forwarding: vxlan_bridge_1d_port_8472: New test
This simple wrapper reruns the VXLAN ping test with a port number of
8472.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:24 +0000 (16:11 +0000)]
selftests: forwarding: vxlan_bridge_1d: Add an ECN decap test
Test that when decapsulating from VXLAN, the values of inner and outer
TOS are handled appropriately. Because VXLAN driver on its own won't
produce the arbitrary TOS combinations necessary to test this feature,
simply open-code a single ICMP packet and have mausezahn assemble it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:22 +0000 (16:11 +0000)]
selftests: forwarding: vxlan_bridge_1d: Add an ECN encap test
Test that ECN bits in the VXLAN envelope are correctly deduced from the
overlay packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:21 +0000 (16:11 +0000)]
selftests: forwarding: vxlan_bridge_1d: Add a TOS test
Test that TOS is inherited from the tunneled packet into the envelope as
configured at the VXLAN device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:20 +0000 (16:11 +0000)]
selftests: forwarding: vxlan_bridge_1d: Add a TTL test
This tests whether TTL of VXLAN envelope packets is properly set based
on the device configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:19 +0000 (16:11 +0000)]
selftests: forwarding: vxlan_bridge_1d: Reconfigure & rerun tests
The ordering of the topology creation can have impact on whether a
driver is successful in offloading VXLAN. Therefore add a pseudo-test
that reshuffles bits of the topology, and then reruns the same suite of
tests again to make sure that the new setup is supported as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:18 +0000 (16:11 +0000)]
selftests: forwarding: vxlan_bridge_1d: Add unicast test
Test that when sending traffic to a learned MAC address, the traffic is
forwarded accurately only to the right endpoint.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:17 +0000 (16:11 +0000)]
selftests: forwarding: vxlan_bridge_1d: Add flood test
Test that when sending traffic to an unlearned MAC address, the traffic
is flooded to both remote VXLAN endpoints.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:15 +0000 (16:11 +0000)]
selftests: forwarding: vxlan_bridge_1d: Add ping test
Test end-to-end reachability between local and remote endpoints.
Note that because learning is disabled on the VXLAN device, the ICMP
requests will end up being flooded to all remotes.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:14 +0000 (16:11 +0000)]
selftests: forwarding: Add a skeleton of vxlan_bridge_1d
This skeleton sets up a topology with three VXLAN endpoints: one
"local", possibly offloaded, and two "remote", formed using veth pairs
and likely purely software bridges. The "local" endpoint is connected to
host systems by a VLAN-unaware bridge.
Since VXLAN tunnels must be unique per namespace, each of the "remote"
endpoints is in its own namespace. H3 forms the bridge between the three
domains.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:13 +0000 (16:11 +0000)]
selftests: forwarding: lib: Add link_stats_rx_errors_get()
Such a function will be useful for counting malformed packets in the ECN
decap test.
To that end, introduce a common handler for handling stat-fetching, and
reuse it in link_stats_tx_packets_get() and link_stats_rx_errors_get().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:12 +0000 (16:11 +0000)]
selftests: forwarding: ping{6, }_do(): Allow passing ping arguments
Make the ping routine more generic by allowing passing arbitrary ping
command-line arguments.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:11 +0000 (16:11 +0000)]
selftests: forwarding: ping{6, }_test(): Add description argument
Have ping_test() recognize an optional argument with a description of
the test. This is handy if there are several ping test, to make it clear
which is which.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:10 +0000 (16:11 +0000)]
selftests: forwarding: lib: Add in_ns()
In order to run a certain command inside another network namespace, it's
possible to use "ip netns exec ns command". However then one can't use
functions defined in lib.sh or a test suite.
One option is to do "ip netns exec ns bash -c command", provided that
all functions that one wishes to use (and their dependencies) are
published using "export -f". That may not be practical.
Therefore, introduce a helper in_ns(), which wraps a given command in a
boilerplate of "ip netns exec" and "source lib.sh", thus making all
library functions available. (Custom functions that a script wishes to
run within a namespace still need to be exported.)
Because quotes in "$@" aren't recognized in heredoc, hand-expand the
array in an explicit for loop, leveraging printf %q to handle proper
quoting.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:08 +0000 (16:11 +0000)]
selftests: forwarding: lib: Support NUM_NETIFS of 0
So far the case of NUM_NETIFS of 0 has not been interesting. However if
one wishes to reuse the lib.sh routines in a setup of a separate
namespace, being able to import like this is handy.
Therefore replace the {1..$NUM_NETIFS} references, which cause iteration
over 1 and 0, with an explicit for loop like we do in setup_wait() and
tc_offload_check(), so that for NUM_NETIFS of 0 no iteration is done.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Mon, 19 Nov 2018 16:11:07 +0000 (16:11 +0000)]
net: skb_scrub_packet(): Scrub offload_fwd_mark
When a packet is trapped and the corresponding SKB marked as
already-forwarded, it retains this marking even after it is forwarded
across veth links into another bridge. There, since it ingresses the
bridge over veth, which doesn't have offload_fwd_mark, it triggers a
warning in nbp_switchdev_frame_mark().
Then nbp_switchdev_allowed_egress() decides not to allow egress from
this bridge through another veth, because the SKB is already marked, and
the mark (of 0) of course matches. Thus the packet is incorrectly
blocked.
Solve by resetting offload_fwd_mark() in skb_scrub_packet(). That
function is called from tunnels and also from veth, and thus catches the
cases where traffic is forwarded between bridges and transformed in a
way that invalidates the marking.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Nov 2018 01:56:09 +0000 (17:56 -0800)]
Merge branch 'octeontx2-af-NPC-MCAM-support-and-FLR-handling'
Sunil Goutham says:
====================
octeontx2-af: NPC MCAM support and FLR handling
This patchset is a continuation to earlier submitted three patch
series to add a new driver for Marvell's OcteonTX2 SOC's
Resource virtualization unit (RVU) admin function driver.
1. octeontx2-af: Add RVU Admin Function driver
https://www.spinics.net/lists/netdev/msg528272.html
2. octeontx2-af: NPA and NIX blocks initialization
https://www.spinics.net/lists/netdev/msg529163.html
3. octeontx2-af: NPC parser and NIX blocks initialization
https://www.spinics.net/lists/netdev/msg530252.html
This patch series adds support for below
RVU generic:
- Function Level Reset irq handler
When FLR is triggered for PFs, AF receives interrupt.
This patchset adds logic for cleaning up of NPA, NIX
and NPC block resources being used by PF.
- Mailbox communication between AF and it's VFs.
Unlike VFs of PF1-PFn, AF which is PF0 can communicate
with it's VFs directly. Added support for the same.
- AF's VFs IO configuration
These VFs are mapped to use internal HW loopback channels
instead of CGX LMACs. Each pair of VFs work as two of ends
of hardwired interfaces. VF0's TX is VF1's Rx & viceversa.
NPC block:
- MCAM entry management
Alloc/Free of contiguous/non-contiguous and lower/higher
priority MCAM entry allocation and programming support.
- MCAM counters management and map/unmap with MCAM entries
- Default KEY extract profile
- HW errata workarounds
NIX block:
- Minimum and maximum allowed packet length config
- HW errata workarounds
Few more changes like shift to use mutex instead of spinlock etc
are done in this patchset.
Changes from v2:
1 Fixed commit message of patch 'Relax resource lock into mutex'
to a more unambiguous one.
- Suggested by David Miller.
Changes from v1:
1 Converted all mailbox message handler API names to small letters
from mixed small and capital letters.
- Suggested by David Miller.
2 Fixed endian issues in patch 'Add support for stripping STAG/CTAG'
- Suggested by Arnd Bergmann
3 Elaborated commit message of patch 'Add FLR interrupt handler'
to make it a bit more easy to understand.
- Suggested by Arnd Bergmann
Will fix the padding and alignment in mailbox message structure
in a follow-up patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:43 +0000 (16:17 +0530)]
octeontx2-af: Workarounds for HW errata
Errata 35038
Software sets NIX_AF_RX_SW_SYNC[ENA] to sync (flush) in-flight packets
the RX data path before configuration changes (e.g. disabling one or
more RQs). Hardware clears [ENA] to indicate sync is done
An issue exists whereby NIX may clear NIX_AF_RX_SW_SYNC [ENA] too
early.
Errata 35057
NIX may corrupt internal state when conditional clocks turn off.
So turnon all clocks by default.
Errata 35786
Parse nibble enable NPC configuration for KEY generation has to be
identical for both Rx and Tx interfaces.
Also corrected endianness configuration for NIX i.e NIX_AF_CFG[AF_BE]
is bit8 and not bit1.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linu Cherian [Mon, 19 Nov 2018 10:47:42 +0000 (16:17 +0530)]
octeontx2-af: Add interrupt handlers for Master Enable event
- Add interrupt handlers for Master Enable events from PFs
and Master Enable events from VFs of AF
- Master Enable is required for the MSIX delivery to work
- Master Enable bit trap handler doesn't have to do any anything
other than clearing the TRPEND bit, since the enable/disable
requirements are already taken care using mbox requests/flr handler.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:41 +0000 (16:17 +0530)]
octeontx2-af: Add FLR handling support for AF's VFs
Added support to handle FLR for AF's VFs (i.e LBK VFs).
Just the FLR interrupt enable/disable, handler registration
etc, actual HW resource cleanup or LFs teardown logic is
already there.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomasz Duszynski [Mon, 19 Nov 2018 10:47:40 +0000 (16:17 +0530)]
octeontx2-af: Configure AF VFs to talk over LBK channels
Configure AF VFs such that they are able to talk over consecutive
loopback channels.
If 8 VFs are attached to AF then communication will work as below:
TX RX
lbk0 -> lbk1
lbk1 -> lbk0
lbk2 -> lbk3
lbk3 -> lbk2
lbk4 -> lbk5
lbk5 -> lbk4
lbk6 -> lbk7
lbk7 -> lbk6
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomasz Duszynski [Mon, 19 Nov 2018 10:47:39 +0000 (16:17 +0530)]
octeontx2-af: Enable sriov on AF to create VFs
Enable all AF VFs during probe. Since AF's VFs work in pairs
(eg: Pkts sent on VF0 are received by VF1 and viceversa),
enable only even number of VFs out of totalVFs, which should
again be less than number of loopback (LBK) channels.
Also enable VF's mailbox interrupts.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomasz Duszynski [Mon, 19 Nov 2018 10:47:38 +0000 (16:17 +0530)]
octeontx2-af: Mbox communication support btw AF and it's VFs
VFs attached to PFs other than AF can not communicate with AF
directly. Instead they are supposed to first send message to
the PF they are residing on and PF forwards it to the AF.
Responses to messages are handled in the reverse order.
On the other hand if VFs are on AF (PF0) itself then direct mailbox
communication is possible since there's no other PF in the way.
This patch addresses this particular case and adds support for
handling it.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Marko Kallio <mkallio@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geetha sowjanya [Mon, 19 Nov 2018 10:47:37 +0000 (16:17 +0530)]
octeontx2-af: Teardown NPA, NIX LF upon receiving FLR
Upon receiving FLR IRQ for a RVU PF, teardown or cleanup
resources held by that PF_FUNC. This patch cleans up,
NIX LF
- Stop ingress/egress traffic
- Disable NPC MCAM entries being used.
- Free Tx scheduler queues
- Disable RQ/SQ/CQ HW contexts
NPA LF
- Disable Pool/Aura HW contexts
In future teardown of SSO/SSOW/TIM/CPT will be added.
Also added a mailbox message for a RVU PF to request
AF, to perform FLR for a RVU VF under it.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geetha sowjanya [Mon, 19 Nov 2018 10:47:36 +0000 (16:17 +0530)]
octeontx2-af: Add FLR interrupt handler
RVU admin function (AF) has all the priviliges to cleanup
HW state when VFIO triggers a PCIe function level reset (FLR)
due to either reset or a VM crash. FLR for RVU PF1-PFn will
trigger an IRQ to AF.
This patch enables all RVU PF's FLR interrupts and registers a
handler. Upon receiving an interrupt, a workqueue is scheduled
to cleanup all hardware blocks being used by the PF which
received the FLR.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:35 +0000 (16:17 +0530)]
octeontx2-af: Verify NPA/SSO/NIX PF_FUNC mapping
While mapping a NIX LF to a NPA LF attached PF_FUNC or
SSO LF attached PF_FUNC, verify if PF_FUNC is valid and
if that PF_FUNC has a LF of that block attached to it or not.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomasz Duszynski [Mon, 19 Nov 2018 10:47:34 +0000 (16:17 +0530)]
octeontx2-af: Add support for stripping STAG/CTAG
This works by shadowing existing UCAST MCAM entry
with a new one additionally matching either NPC_LT_LB_CTAG
or NPC_LT_LB_STAG. For this to fully work one needs to
send properly configured NIX_VTAG_CFG message afterwards i.e with
strip and capture enabled and type set to 0.
On receiving tagged packet NIX will remove outer VLAN and capture
TCI in NIX_RX_PARSE_S.
Also simplified RX Vtag configuration flow
With this setting STRIP/CAPTURE VTAG actions separately would be
possible. Following combinations are possible: STRIP,
STRIP and CAPTURE, CAPTURE or nothing (0 disables respective actions).
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:33 +0000 (16:17 +0530)]
octeontx2-af: Support to enable/disable default MCAM entries
For a PF/VF with a NIXLF attached has default/reserved MCAM entries
for receiving Ucast/Bcast/Promisc traffic. Ideally traffic should be
forwarded to NIXLF only after it's contexts are initialized. This
patch keeps these default entries disabled and adds mbox messages
for a PF/VF to enable these once NPA/NIXLF initialization is done.
Likewise while PF/VF is being teared down, it can send the disable
mailbox message to stop receiving traffic.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Shukla [Mon, 19 Nov 2018 10:47:32 +0000 (16:17 +0530)]
octeontx2-af: Add MKEX default profile
Added basic default MKEX profile. This profile tells
hardware what data to extract from packet and where to
place it (bit offset) in final KEY generated for the
parsed packet. Based on the bit placement of the packet
data, MCAM entries have to programmed for matching.
Also added a msg to retrieve this MKEX profile from PF/VF
which inturn can process it to determine how MCAM entry
has to be populated.
Signed-off-by: Santosh Shukla <sshukla@marvell.com>
Signed-off-by: Yuri Tolstov <ytolstov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:31 +0000 (16:17 +0530)]
octeontx2-af: Alloc and config NPC MCAM entry at a time
A new mailbox message is added to support allocating a MCAM entry
along with a counter and configuring it in one go. This reduces
the amount of mailbox communication involved in installing a new
MCAM rule.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:30 +0000 (16:17 +0530)]
octeontx2-af: Map or unmap NPC MCAM entry and counter
Alloc memory to save MCAM 'entry to counter' mapping and since
multiple entries can map to same counter, added counter's reference
count tracking.
Do 'entry to counter' mapping when a entry is being installed
and mbox msg sender requested to configure a counter as well.
Mapping is removed when a entry or counter is being freed or
a explicit mbox msg is received to unmap them.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:29 +0000 (16:17 +0530)]
octeontx2-af: Support for NPC MCAM counters
NPC HW has counters which can be mapped to MCAM
entries to gather entry match statistics. This
patch adds support to allocate, free, clear and retrieve
stats of NPC MCAM counters. New mailbox messages have
been added for this. Similar to MCAM entries both
contiguous and non-contiguous counter allocation is
supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:28 +0000 (16:17 +0530)]
octeontx2-af: MCAM entry installation support
Add support for a RVU PF/VF to enable, disable, configure
and shuffle MCAM entries via mbox commands. This patch adds
mailbox message formats and handling of these commands.
As of now otherthan validating MCAM entry index, info like
channel number e.t.c in MCAM config data sent by PF/VF are
not validated.
Also a max of 64 MCAM entries can be shuffled with a single
mbox command.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:27 +0000 (16:17 +0530)]
octeontx2-af: NPC MCAM entry alloc/free support
This patch adds NPC MCAM entry management and support for
allocating and freeing them via mailbox. Both contiguous and
non-contiguous allocations are supported. Incase of contiguous,
if request cannot be met then max contiguous number of available
entries are allocated.
High or low priority index allocation w.r.t a reference MCAM index
is also supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanislaw Kardach [Mon, 19 Nov 2018 10:47:26 +0000 (16:17 +0530)]
octeontx2-af: Relax resource lock into mutex
Mailbox message handling is done in a workqueue context scheduled
from interrupt handler. So resource locks does not need to be a spinlock.
Therefore relax them into a mutex so that later on we may use them
in routines that might sleep.
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kiran Kumar [Mon, 19 Nov 2018 10:47:25 +0000 (16:17 +0530)]
octeontx2-af: Support to get NIX HW constants from AF
This patch adds reading HW limits like number of Rx/Tx stats,
number of queue IRQs supported per NIX LF from AF registers
and sync them to PF/VF.
Signed-off-by: Kiran Kumar <kirankumark@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:24 +0000 (16:17 +0530)]
octeontx2-af: Support to modify min/max allowed packet lengths
This patch adds support for RVU PF/VFs to modify min/max
packet lengths allowed by HW. For VFs on PF0, settings will
be automatically applied on LBK link. RX link's min/maxlen
is configured to min/max of PF and it's all VFs. On the TX side
if requested all SMQs attached to the requesting NIXLF will be
updated with new min/max lengths.
Also updates transmit credits for Tx links based on new maxlen.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Mon, 19 Nov 2018 10:47:23 +0000 (16:17 +0530)]
octeontx2-af: Convert mbox handlers APIs to lowercase
This patch converts all mailbox message handler API
names to lowercase.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 20 Nov 2018 01:32:15 +0000 (17:32 -0800)]
Merge branch 'r8169-series-with-further-smaller-improvements'
Heiner Kallweit says:
====================
r8169: series with further smaller improvements
Again nothing exciting, just smaller improvements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:41:35 +0000 (22:41 +0100)]
r8169: improve chip version identification
Only the upper 12 bits are used for chip identification, this helps
to reduce the size of array mac_info.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:40:04 +0000 (22:40 +0100)]
r8169: simplify ocp functions
rtl8168_oob_notify is used in rtl8168dp_driver_start and
rtl8168dp_driver_stop only, so we can rename it to r8168dp_oob_notify.
The same applies to condition rtl_ocp_read_cond which can be renamed
to rtl_dp_ocp_read_cond. This allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:39:14 +0000 (22:39 +0100)]
r8169: remove workaround for ancient gcc bug
The kernel can't be built any longer with this ancient GCC version.
Eventually it becomes clear what this statement actually does.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:38:22 +0000 (22:38 +0100)]
r8169: remove manual padding in struct ring_info
The compiler takes care of alignment and padding, I see no need to
bother him with manual hints.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:37:34 +0000 (22:37 +0100)]
r8169: remove "not PCI Express" message
The ones who want to know can easily identify whether chip is PCI or
PCIe based on the chip name. I doubt there's any benefit in this
message, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:36:15 +0000 (22:36 +0100)]
r8169: remove print_mac_version
The syslog message printed on driver load allows to easily identify
the mac version number (based on chip name and XID). So we don't
need this extra debug message which is wrong anyway because e.g.
RTL_GIGA_MAC_VER_01 has value 0.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:35:08 +0000 (22:35 +0100)]
r8169: use PCI_VDEVICE macro
Using macro PCI_VDEVICE helps to simplify the PCI ID table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:34:17 +0000 (22:34 +0100)]
r8169: replace event_slow with irq_mask
Recently the "slow event" handler was removed, therefore the member
name isn't appropriate any longer. In addition store the full mask,
including the RTL_EVENT_NAPI interrupt source bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:33:00 +0000 (22:33 +0100)]
r8169: remove unused interrupt sources
Setting PCSTimeout interrupt source was copied from the vendor driver
which uses the chip programmable timer interrupt. The mainline driver
doesn't use this timer interrupt.
SYSErr indicates a PCI error and isn't defined on the PCIe models.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:32:18 +0000 (22:32 +0100)]
r8169: use dev_get_drvdata where possible
Using dev_get_drvdata directly is simpler here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 19 Nov 2018 21:31:32 +0000 (22:31 +0100)]
r8169: merge rtl_irq_enable and rtl_irq_enable_all
After the recent changes to the interrupt handler rtl_irq_enable and
rtl_irq_enable_all can be merged.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Nov 2018 20:25:43 +0000 (12:25 -0800)]
Merge branch 'sctp-add-subscribe-per-asoc-and-sockopt-SCTP_EVENT'
Xin Long says:
====================
sctp: add subscribe per asoc and sockopt SCTP_EVENT
This patchset mainly adds the Event Subscription sockopt described in
rfc6525#section-6.2:
"Subscribing to events as described in [RFC6458] uses a setsockopt()
call with the SCTP_EVENT socket option. This option takes the
following structure, which specifies the association, the event type
(using the same value found in the event type field), and an on/off
boolean.
struct sctp_event {
sctp_assoc_t se_assoc_id;
uint16_t se_type;
uint8_t se_on;
};
The user fills in the se_type field with the same value found in the
strreset_type field, i.e., SCTP_STREAM_RESET_EVENT. The user will
also fill in the se_assoc_id field with either the association to set
this event on (this field is ignored for one-to-one style sockets) or
one of the reserved constant values defined in [RFC6458]. Finally,
the se_on field is set with a 1 to enable the event or a 0 to disable
the event."
As for the old SCTP_EVENTS Option with struct sctp_event_subscribe,
it's being DEPRECATED.
v1->v2:
- fix some key word in changelog that triggerred the filters at
vger.kernel.org.
v2->v3:
- fix an array out of bounds noticed by Neil in patch 1/4.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 18 Nov 2018 08:08:54 +0000 (16:08 +0800)]
sctp: add sockopt SCTP_EVENT
This patch adds sockopt SCTP_EVENT described in rfc6525#section-6.2.
With this sockopt users can subscribe to an event from a specified
asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 18 Nov 2018 08:08:53 +0000 (16:08 +0800)]
sctp: rename enum sctp_event to sctp_event_type
sctp_event is a structure name defined in RFC for sockopt
SCTP_EVENT. To avoid the conflict, rename it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 18 Nov 2018 08:08:52 +0000 (16:08 +0800)]
sctp: add subscribe per asoc
The member subscribe should be per asoc, so that sockopt SCTP_EVENT
in the next patch can subscribe a event from one asoc only.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 18 Nov 2018 08:08:51 +0000 (16:08 +0800)]
sctp: define subscribe in sctp_sock as __u16
The member subscribe in sctp_sock is used to indicate to which of
the events it is subscribed, more like a group of flags. So it's
better to be defined as __u16 (2 bytpes), instead of struct
sctp_event_subscribe (13 bytes).
Note that sctp_event_subscribe is an UAPI struct, used on sockopt
calls, and thus it will not be removed. This patch only changes
the internal storage of the flags.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Nov 2018 18:55:00 +0000 (10:55 -0800)]
Merge git://git./linux/kernel/git/davem/net
Linus Torvalds [Mon, 19 Nov 2018 17:24:04 +0000 (09:24 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix some potentially uninitialized variables and use-after-free in
kvaser_usb can drier, from Jimmy Assarsson.
2) Fix leaks in qed driver, from Denis Bolotin.
3) Socket leak in l2tp, from Xin Long.
4) RSS context allocation fix in bnxt_en from Michael Chan.
5) Fix cxgb4 build errors, from Ganesh Goudar.
6) Route leaks in ipv6 when removing exceptions, from Xin Long.
7) Memory leak in IDR allocation handling of act_pedit, from Davide
Caratti.
8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.
9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
Sabrina Dubroca.
10) When NAPI cached skb is reused, we must set it to the proper initial
state which includes skb->pkt_type. From Eric Dumazet.
11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.
12) Set RX queue properly in various tuntap receive paths, from Matthew
Cover.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tuntap: fix multiqueue rx
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
tipc: don't assume linear buffer when reading ancillary data
tipc: fix lockdep warning when reinitilaizing sockets
net-gro: reset skb->pkt_type in napi_reuse_skb()
tc-testing: tdc.py: Guard against lack of returncode in executed command
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
ip_tunnel: don't force DF when MTU is locked
MAINTAINERS: Add entry for CAKE qdisc
net: bridge: fix vlan stats use-after-free on destruction
socket: do a generic_file_splice_read when proto_ops has no splice_read
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
net/sched: act_pedit: fix memory leak when IDR allocation fails
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
ipv6: fix a dst leak when removing its exception
net: mvneta: Don't advertise 2.5G modes
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
net/mlx4: Fix UBSAN warning of signed integer overflow
...
Matthew Cover [Sun, 18 Nov 2018 07:46:00 +0000 (00:46 -0700)]
tuntap: fix multiqueue rx
When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.
Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.
The rx traffic can be generated by either of the following.
1. a simple tap program which spins up multiple queues and writes packets
to each of the file descriptors
2. tx from a qemu vm with a tap multiqueue netdev
The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
1. a simple netmap program which opens and reads from per-queue
descriptors
2. configuring RPS and doing per-cpu captures with rxtxcpu
Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.
Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: Matthew Cover <matthew.cover@stackpath.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sun, 18 Nov 2018 18:45:30 +0000 (10:45 -0800)]
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.
Fixes:
ca254490c8df ("net: Add VRF support to IPv6 stack")
Reported-by: Preethi Ramachandra <preethir@juniper.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Sun, 18 Nov 2018 16:43:03 +0000 (16:43 +0000)]
mlxsw: spectrum: Expose discard counters via ethtool
Expose packets discard counters via ethtool to help with debugging.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 18 Nov 2018 15:37:33 +0000 (07:37 -0800)]
tun: use netdev_alloc_frag() in tun_napi_alloc_frags()
In order to cook skbs in the same way than Ethernet drivers,
it is probably better to not use GFP_KERNEL, but rather
use the GFP_ATOMIC and PFMEMALLOC mechanisms provided by
netdev_alloc_frag().
This would allow to use tun driver even in memory stress
situations, especially if swap is used over this tun channel.
Fixes:
90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petar Penkov <peterpenkov96@gmail.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Nov 2018 00:16:20 +0000 (16:16 -0800)]
Merge branch 'IP101GR-devicetree-based-configuration-of-SEL_INTR32'
Martin Blumenstingl says:
====================
IP101GR: devicetree based configuration of SEL_INTR32
The IP101GR is a 32-pin QFN package variant of the IP101G/IP101GA
Ethernet PHY. Due to it's limited amount of pins the RXER (receive
error) and INTR32 (interrupt) functions share pin 21.
The goal of this series is:
- some small cleanups in patches 3, 4 and 5
- allowing the kernel to detect IRQ floods on boards where the IP101GR
is configured in RXER mode but the RXER line is configured on the
host SoC as interrupt line (patch 6)
- configuration of the SEL_INTR32 register so we can use the interrupt
function on boards where the RXER/INTR32 pin (pin 21) is routed to
one of the host SoC's interrupt inputs (patches 1, 2, 7)
A use-case where this is needed is the Endless Mini (EC-100). I have
tested my changes on that board. This also confirms that Heiner
Kallweit's recent icplus.c PHY driver changes are working (at least on
my setup).
This series is based on net-next commit
7c460cf9cd1a ("net: aquantia:
fix spelling mistake "specfield" -> "specified"")
Changes since v1 at [0]:
- collected Andrew's Reviewed-by's (thank you!)
- updated description of patch #2 to explain why two properties were
added instead of adding an "this is a IP101GR" property
- validate that there's no conflicting configuration in patch #7
- rebased on top of latest net-next
[0] https://patchwork.ozlabs.org/cover/999371/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl [Sun, 18 Nov 2018 21:23:59 +0000 (22:23 +0100)]
net: phy: icplus: allow configuring the interrupt function on IP101GR
The IP101GR is a 32-pin QFN package variant of the IP101G/IP101GA
Ethernet PHY. Due to it's limited amount of pins the RXER (receive
error) and INTR32 (interrupt) functions share pin 21.
By default the PHY is configured to output the "receive error" status on
pin 21. Depending on the board layout and requirements we may want to
re-configure the PHY to output the interrupt signal there.
The mode of pin 21 can be configured in the "Digital I/O Specific
Control Register" (register 29), bit 2:
- 0 = RXER function
- 1 = INTR(32) function
Depending on the devicetree configuration we will now:
- change the mode to either ther RXER or INTR32 function
- keep the SEL_INTR32 value set by the bootloader (default) if no
configuration is provided (to ensure that we're not breaking existing
boards)
- error out if conflicting configuration is given (RXER and INTR32 mode
are enabled at the same time)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl [Sun, 18 Nov 2018 21:23:58 +0000 (22:23 +0100)]
net: phy: icplus: implement .did_interrupt for IP101A/G
The IP101A_G_IRQ_CONF_STATUS register has bits to detect which
interrupts have fired. Implement the .did_interrupt callback to let the
PHY core know whether the interrupt was for this specific PHY.
This is useful for debugging interrupt problems with 32-pin IP101GR PHYs
where the interrupt line is shared with the RX_ERR (receive error
status) signal. The default values are:
- RX_ERR is enabled by default (LOW means that there is no receive
error)
- the PHY's interrupt line is configured "active low" by default
Without any additional changes there is a flood of interrupts if the
RX_ERR/INTR32 signal is configured in RX_ERR mode (which is the
default). Having a did_interrupt ensures that the PHY core returns
IRQ_NONE instead of endlessly triggering the PHY state machine.
Additionally the kernel will report this after a while:
irq 28: nobody cared (try booting with the "irqpoll" option)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl [Sun, 18 Nov 2018 21:23:57 +0000 (22:23 +0100)]
net: phy: icplus: rename IP101A_G_NO_IRQ to IP101A_G_IRQ_ALL_MASK
The datasheet uses the name "All Mask" for this bit. Change the name of
our #define to be consistent with the datasheet. While here also replace
the tab between the #define and IP101A_G_IRQ_ALL_MASK with a space.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl [Sun, 18 Nov 2018 21:23:56 +0000 (22:23 +0100)]
net: phy: icplus: use the BIT macro where possible
This makes the code consistent by using the BIT() macro instead of
manual bit-shifting for some of the fields. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl [Sun, 18 Nov 2018 21:23:55 +0000 (22:23 +0100)]
net: phy: icplus: keep all ip101a_g functions together
This simply moves ip101a_g_config_init right above
ip101a_g_config_intr so all functions for the ICPlus IP101A/G PHYs are
grouped together.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl [Sun, 18 Nov 2018 21:23:54 +0000 (22:23 +0100)]
dt-bindings: net: phy: add bindings for the IC Plus Corp. IP101A/G PHYs
The IP101A and IP101G series both have various models. Depending on the
board implementation we need a special property for the IP101GR (32-pin
LQFP package) PHY:
pin 21 ("RXER/INTR_32") outputs the "receive error" signal by default
(LOW means "normal operation", HIGH means that there's either a decoding
error of the received signal or that the PHY is receiving LPI). This pin
can also be switched to INTR32 mode, where the interrupt signal is
routed to this pin. The other PHYs don't need this special handling
because they have more pins available so the interrupt function gets a
dedicated pin.
This adds two properties to either select the "receive error" or
"interrupt" function of pin 21. Not specifying any function means that
the default set by the bootloader is used. This is required because the
IP101GR cannot be differentiated between other IP101 PHYs as the PHY
identification registers on all of these is 0x02430c54.
The IP101G (sold as die only, without package) may suffer from the same
issue depending on how it's integrated into a multi chip package by
another manufacturer. If only the RXER/INTR_32 pin is routed then the
users of the die-only variant may also have to explicitly configure the
mode of hte RXER/INTR_32 pin. This is the reason why no "is-ip101gr"
property was added. I have no evidence though which would confirm this
theory - so the binding itself is independent of that.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Blumenstingl [Sun, 18 Nov 2018 21:23:53 +0000 (22:23 +0100)]
dt-bindings: vendor-prefix: add prefix for IC Plus Corp.
IC Plus Corp. has various Ethernet related products such as Ethernet
transceivers, Ethernet controllers, Ethernet switches, etc.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Nov 2018 21:33:44 +0000 (13:33 -0800)]
Linux 4.20-rc3
thesven73@gmail.com [Sat, 17 Nov 2018 15:56:18 +0000 (10:56 -0500)]
tg3: optionally use eth_platform_get_mac_address() to get mac address
This function will try to determine the mac address via the devicetree,
or via an architecture-specific method (e.g. a PROM on SPARC).
The SPARC-specific code in this driver (#ifdef SPARC) did exactly this,
and is therefore removed.
Note that you can now specify the tg3 mac address via the devicetree,
on any platform, not just SPARC:
Devicetree example:
(see Documentation/devicetree/bindings/pci/pci.txt)
&pcie {
host@0 {
#address-cells = <3>;
#size-cells = <2>;
reg = <0 0 0 0 0>;
bcm5778: bcm5778@0 {
reg = <0 0 0 0 0>;
mac-address = [CA 11 AB 1E 10 01];
};
};
};
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
yupeng [Fri, 16 Nov 2018 19:17:40 +0000 (11:17 -0800)]
net: Add part of TCP counts explanations in snmp_counters.rst
Add explanations of some generic TCP counters, fast open
related counters and TCP abort related counters and several
examples.
Signed-off-by: yupeng <yupeng0921@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Nov 2018 20:21:09 +0000 (12:21 -0800)]
Merge tag 'libnvdimm-fixes-4.20-rc3' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A small batch of fixes for v4.20-rc3.
The overflow continuation fix addresses something that has been broken
for several releases. Arguably it could wait even longer, but it's a
one line fix and this finishes the last of the known address range
scrub bug reports. The revert addresses a lockdep regression. The unit
tests are not critical to fix, but no reason to hold this fix back.
Summary:
- Address Range Scrub overflow continuation handling has been broken
since it was initially merged. It was only recently that error
injection and platform-BIOS support enabled this corner case to be
exercised.
- The recent attempt to provide more isolation for the kernel Address
Range Scrub state machine from userapace initiated sessions
triggers a lockdep report. Revert and try again at the next merge
window.
- Fix a kasan reported buffer overflow in libnvdimm unit test
infrastrucutre (nfit_test)"
* tag 'libnvdimm-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
Revert "acpi, nfit: Further restrict userspace ARS start requests"
acpi, nfit: Fix ARS overflow continuation
tools/testing/nvdimm: Fix the array size for dimm devices.
Linus Torvalds [Sun, 18 Nov 2018 19:31:26 +0000 (11:31 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/memblock.c: fix a typo in __next_mem_pfn_range() comments
mm, page_alloc: check for max order in hot path
scripts/spdxcheck.py: make python3 compliant
tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
mm/vmstat.c: fix NUMA statistics updates
mm/gup.c: fix follow_page_mask() kerneldoc comment
ocfs2: free up write context when direct IO failed
scripts/faddr2line: fix location of start_kernel in comment
mm: don't reclaim inodes with many attached pages
mm, memory_hotplug: check zone_movable in has_unmovable_pages
mm/swapfile.c: use kvzalloc for swap_info_struct allocation
MAINTAINERS: update OMAP MMC entry
hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
kernel/sched/psi.c: simplify cgroup_move_task()
z3fold: fix possible reclaim races
Linus Torvalds [Sun, 18 Nov 2018 18:58:20 +0000 (10:58 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix an exec() related scalability/performance regression, which was
caused by incorrectly calculating load and migrating tasks on exec()
when they shouldn't be"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix cpu_util_wake() for 'execl' type workloads
Linus Torvalds [Sun, 18 Nov 2018 18:54:59 +0000 (10:54 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Fix uncore PMU enumeration for CofeeLake CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Support CoffeeLake 8th CBOX
perf/x86/intel/uncore: Add more IMC PCI IDs for KabyLake and CoffeeLake CPUs