OSDN Git Service
Johannes Berg [Mon, 22 Apr 2013 13:31:43 +0000 (15:31 +0200)]
Merge remote-tracking branch 'wireless-next/master' into mac80211-next
Johannes Berg [Thu, 18 Apr 2013 23:02:55 +0000 (01:02 +0200)]
nl80211: allow using wdev identifiers to get scan results
Most dump callbacks, including the scan results one, use
the netdev to identify what to do, which is incorrect for
the P2P_DEVICE support, it needs to be able to get the
scan result from the wdev. Change all dumps to unify the
code, but ones other than scan don't really support being
executed on a wdev that has no netdev.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 18 Apr 2013 21:42:19 +0000 (23:42 +0200)]
mac80211: fix P2P-Device management frame RX
There's an issue in receiving broadcast management frames
on P2P Device virtual interfaces, such frames have the RX
flag IEEE80211_RX_RA_MATCH cleared and are thus dropped
in ieee80211_rx_h_mgmt_check(). They should be let through
to make it to ieee80211_rx_h_userspace_mgmt() and then to
userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Karl Beldan [Wed, 17 Apr 2013 11:43:22 +0000 (13:43 +0200)]
mac80211: optimize minstrel_ewma
Use powers of two in ewma of minstrel.
This changes :
- EWMA_DIV from 100 to 2^7
- EWMA_LEVEL from 75 (/EWMA_DIV=100) to 2^6 + 2^5 (/EWMA_DIV=128)
Note that this changes EWMA_DIV - EWMA_LEVEL from 25 to 2^5 and keeps
EWMA_LEVEL / EWMA_DIV == 0.75.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Karl Beldan [Wed, 17 Apr 2013 12:08:26 +0000 (14:08 +0200)]
mac80211: cosmetics for minstrel_debugfs
This changes the minstrel stats ouput from:
rate throughput ewma prob this prob this succ/attempt success attempts
BCD 6 0.0 0.0 0.0 0( 0) 0 0
to:
rate throughput ewma prob this prob this succ/attempt success attempts
BCD 6 0.0 0.0 0.0 0( 0) 0 0
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 17 Apr 2013 09:26:40 +0000 (11:26 +0200)]
mac80211: fix station entry leak/warning while suspending
Since Stanislaw's patches, when suspending while connected,
cfg80211 will disconnect. This causes the AP station to be
removed, which uses call_rcu() to clean up. Due to needing
process context, this queues a work struct on the mac80211
workqueue. This will warn and fail when already suspended,
which can happen if the rcu call doesn't happen quickly.
To fix this, replace the synchronize_net() which is really
just synchronize_rcu_expedited() with rcu_barrier(), which
unlike synchronize_rcu() waits until RCU callback have run
and thus avoids this issue.
In theory, this can even happen without Stanislaw's change
to disconnect on suspend since userspace might disconnect
just before suspending, though then it's unlikely that the
call_rcu() will be delayed long enough.
Cc: stable@vger.kernel.org [3.7+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 16 Apr 2013 11:38:43 +0000 (13:38 +0200)]
mac80211: fix CTS protection handling
The rates[0] CTS and RTS flags are only set after rate control has been
called, so minstrel cannot use them to for setting the number of
retries. This patch adds two new flags to explicitly indicate RTS/CTS use.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 16 Apr 2013 11:38:42 +0000 (13:38 +0200)]
mac80211: fix and optimize MCS mask handling
Currently the code always copies the configured MCS mask (even if it is
set to default), but only uses it if legacy rates were also masked out.
Fix this by adding a flag that tracks whether the configured MCS mask is
set to default or not.
Optimize the code further by storing a pointer to the configured rate
mask in txrc instead of using memcpy.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Karl Beldan [Mon, 15 Apr 2013 15:09:30 +0000 (17:09 +0200)]
mac80211_hwsim: handle VHT rates in rx_status
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Karl Beldan [Mon, 15 Apr 2013 15:09:29 +0000 (17:09 +0200)]
mac80211: VHT off-by-one NSS
The number of VHT spatial streams (NSS) is found in:
- s8 ieee80211_tx_rate.rate.idx[6:4] (tx - filled by rate control)
- u8 ieee80211_rx_status.vht_nss (rx - filled by driver)
Tx discriminates valid rates indexes with the sign bit and encodes NSS
starting from 0 to 7 (note this matches some hw encodings e.g IWLMVM).
Rx does not have the same constraints, and encodes NSS starting from 1
to 8 (note this matches what wireshark expects in the radiotap header).
To handle ieee80211_tx_rate.rate.idx[6:4] ieee80211_rate_set_vht() and
ieee80211_rate_get_vht_nss() assume their nss parameter and return value
respectively runs from 0 to 7.
ATM, there are only 2 users of these: cfg.c:sta_set_rate_info_t() and
iwlwifi/mvm/tx.c:iwl_mvm_hwrate_to_tx_control(), but both assume nss
runs from 1 to 8.
This patch fixes this inconsistency by making ieee80211_rate_set_vht()
and ieee80211_rate_get_vht_nss() handle an nss running from 1 to 8.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Karl Beldan [Mon, 15 Apr 2013 17:04:06 +0000 (19:04 +0200)]
mac80211: adjust initial chandefs assignments in ieee80211_register_hw
I noticed that monitor interfaces by default would start on 5GHz
while STA/AP ones would start 2GHZ - It stems from the fact that
ieee80211_register_hw unnecessarily adjusts the local->monitor_chandef
for each band.
This avoids this and while at it uses a single dflt_chandef to initialize
in one go local->{hw.conf.chandef,_oper_chandef,monitor_chandef}
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Karl Beldan [Mon, 15 Apr 2013 16:28:21 +0000 (18:28 +0200)]
mac80211: fix rate control tx handler for VHT rates
Handle VHT rates like HT ones, otherwise we easily trigger the pre-HT
rates WARN_ON(rc_rate->idx >= sband->n_bitrates) which will set
rc_rate->idx to -1.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexander Bondar [Tue, 9 Apr 2013 14:14:09 +0000 (17:14 +0300)]
mac80211: remove warning from ieee80211_beacon_loss
Currently, mac80211 assumes that connection monitor offload
for BSS station implies that the device:
- sends periodic keep alive packets to associated AP
- monitors missed beacons
- actively probes the AP in case of missed beacons
In case of poor connection conditions it expects the function
ieee80211_connection_loss() to be called by driver. However,
some devices implement connection monitor offload excluding
active AP probing.
To allow them to call ieee80211_beacon_loss() cleanly, remove
the warning there and thus allow them to use mac80211 for the
AP probing even if connection monitor offload is supported.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 28 Mar 2013 09:44:18 +0000 (10:44 +0100)]
mac80211: handle wide bandwidth channel switch
Parse and react to the wide bandwidth channel switch element
in beacons/action frames. Finding the element was done in a
previous patch (it has different positions in beacons/action
frames), now handle it. If there's something wrong with it
simply disconnect.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 26 Mar 2013 13:54:16 +0000 (14:54 +0100)]
mac80211: parse VHT channel switch IEs
VHT introduces multiple IEs that need to be parsed for a
wide bandwidth channel switch. Two are (currently) needed
in mac80211:
* wide bandwidth channel switch element
* channel switch wrapper element
The former is contained in the latter for beacons and probe
responses, but not for the spectrum management action frames
so the IE parser needs a new argument to differentiate them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 26 Mar 2013 14:17:18 +0000 (15:17 +0100)]
mac80211: handle extended channel switch announcement
Handle the (public) extended channel switch announcement
action frames. Parts of the data in these frames isn't
really in IEs, but put it into the elems struct anyway
to simplify the handling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 25 Mar 2013 17:29:27 +0000 (18:29 +0100)]
mac80211: support secondary channel offset in CSA
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 26 Mar 2013 13:13:58 +0000 (14:13 +0100)]
mac80211: support extended channel switch
Support extended channel switch when the operating
class is one of the global operating classes as
defined in Annex E of 802.11-2012. If it isn't,
disconnect from the AP instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 1 Aug 2012 15:00:55 +0000 (17:00 +0200)]
cfg80211: add ieee80211_operating_class_to_band
This function converts a (global only!) operating
class to an internal band identifier. This will
be needed for extended channel switch support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 26 Mar 2013 13:02:26 +0000 (14:02 +0100)]
mac80211: unify CSA action frame/beacon processing
CSA action frame content should be processed as variable IEs
rather than fixed to make it extensible. Unify the code and
process them just like CSA in beacons to make it easier to
extend for HT/VHT.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 28 Mar 2013 09:26:17 +0000 (10:26 +0100)]
mac80211: use second center_freq segment only in 80+80
The field is otherwise reserved, so we shouldn't read
and reject it, though any sane system will probably
have to set it to 0 anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 16 Apr 2013 12:32:26 +0000 (14:32 +0200)]
wireless: regulatory: fix channel disabling race condition
When a full scan 2.4 and 5 GHz scan is scheduled, but then the 2.4 GHz
part of the scan disables a 5.2 GHz channel due to, e.g. receiving
country or frequency information, that 5.2 GHz channel might already
be in the list of channels to scan next. Then, when the driver checks
if it should do a passive scan, that will return false and attempt an
active scan. This is not only wrong but can also lead to the iwlwifi
device firmware crashing since it checks regulatory as well.
Fix this by not setting the channel flags to just disabled but rather
OR'ing in the disabled flag. That way, even if the race happens, the
channel will be scanned passively which is still (mostly) correct.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hauke Mehrtens [Fri, 12 Apr 2013 15:08:58 +0000 (17:08 +0200)]
b43: use bcma_pmu_spuravoid_pllupdate()
Do not implement this in b43, but use bcma_pmu_spuravoid_pllupdate().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 11 Apr 2013 14:22:08 +0000 (16:22 +0200)]
ath5k: use more idiomatic tracing include style
Pretty much everywhere that uses a trace definition
header that's not in include/trace/events/ uses the
make system for the include path rather than putting
it into the sources, so do that in ath5k as well.
This came up during backporting work (where this is
required), but since all other drivers do it this
way upstream it seemed applicable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 11 Apr 2013 14:15:28 +0000 (16:15 +0200)]
brcm80211: simplify makefiles
This came up during my backporting work but it seems
perfectly appropriate for the kernel as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 11 Apr 2013 11:29:00 +0000 (13:29 +0200)]
brcmfmac: remove ifidx variable from brcmf_fws_process_skb()
The value can be obtained from the struct brcmf_if object pointer
and it is used only twice.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 11 Apr 2013 15:12:04 +0000 (17:12 +0200)]
brcmfmac: rename brcmf_fws_mac_desc_ready()
Replace the function by brcmf_fws_mac_desc_closed(). The new function
is used in the transmit path and in the dequeue worker.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 11 Apr 2013 11:28:58 +0000 (13:28 +0200)]
brcmfmac: pass ifp pointer in brcmf_fws_find_mac_desc()
Instead of passing the ifidx and lookup the ifp inside the
function brcmf_fws_find_mac_desc() simply pass the ifp as
parameter.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 11 Apr 2013 15:08:37 +0000 (17:08 +0200)]
brcmfmac: obtain iftype for firmware-signal descriptor lookup
The function brcmf_fws_find_mac_desc() determines the descriptor
associated with a sk_buff for firmware-signalling. It needs the
interface type to do that. For this a helper function is added in
wl_cfg80211.c.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Fri, 12 Apr 2013 08:55:55 +0000 (10:55 +0200)]
brcmfmac: define and use platform specific data for SDIO.
This patch adds support for platform specific data for SDIO
fullmac devices. Currently OOB interrupts are configured by Kconfig
BRCMFMAC_SDIO_OOB but that is now determined dynamically by checking
availibility of platform data.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 11 Apr 2013 11:28:55 +0000 (13:28 +0200)]
brcmfmac: Add drive strength programming for SDIO 43143.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Thu, 11 Apr 2013 11:28:54 +0000 (13:28 +0200)]
brcmfmac: Add 43143 SDIO support.
Added sdio device id to list of supported devices. 43143 is a new
802.11n single stream device.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 11 Apr 2013 11:28:53 +0000 (13:28 +0200)]
brcmfmac: add BCM4335 sdio interface support
BCM4335 is an a/b/g/n/ac WiFi chip that supports up to 80MHz channel. This patch
adds support for this chip through SDIO interface.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piotr Haber [Thu, 11 Apr 2013 11:28:52 +0000 (13:28 +0200)]
brcmfmac: setup SDIO reset behavior
Set device in a manner that SDIO I/O card reset
will lead to WLAN backplane and PMU state reset.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 11 Apr 2013 11:28:51 +0000 (13:28 +0200)]
brcmfmac: add support for dongle ARM CR4 core
Newer WiFi chip use ARM CR4 core to achieve higher performance. Add necessary
code for host driver in order to support CR4 core.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 11 Apr 2013 11:28:50 +0000 (13:28 +0200)]
brcmfmac: adopt new d11 interface
Adopting the new d11 interface for 11ac fullmac chip support.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 11 Apr 2013 11:28:49 +0000 (13:28 +0200)]
brcmutil: add new d11 interface support
802.11 core interface is upgraded with 11ac support. Add channel spec support
code to brcmutil.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 11 Apr 2013 11:28:48 +0000 (13:28 +0200)]
brcmfmac: move chip download state code to sdio_chip.c
enter/exit download state routine is going to diverge with new ARM core
introduced. Move corresponding code to sdio_chip.c for new ARM core support.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Thu, 11 Apr 2013 11:28:47 +0000 (13:28 +0200)]
brcmfmac: aggregate dongle ram access interface
For fullmac chips host driver can access to dongle RAM through SDIO function 1.
Introduce brcmf_sdio_ramrw and place it at bcmsdh.c with other interface
functions.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piotr Haber [Thu, 11 Apr 2013 11:28:46 +0000 (13:28 +0200)]
brcmfmac: support save&restore firmware feature
Save & restore is an advanced power saving feature,
supported only on selected devices.
SR operation is almost completely transparent to the driver.
Support for it is hardware and firmware dependent.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Karl Beldan [Fri, 5 Apr 2013 10:06:24 +0000 (12:06 +0200)]
mac80211: always pick a basic rate to tx RTS/CTS for pre-HT rates
When the 1st rate control entry is a pre-HT rate we want to set
rts_cts_rate_idx "as the fastest basic rate that is not faster than the
data rate"(code comments).
But in case some bss allowed rate indexes are lower than the lowest bss
basic rate, if the rate control selects a rate among the formers for its
1st rate control entry, rts_cts_rate_idx remains 0 and is not a basic
rate index.
This commit sets rts_cts_rate_idx to the lowest bss basic rate index in
this situation.
Note that the code assumes that lowest indexes == lowest bitrates.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Wed, 10 Apr 2013 22:41:40 +0000 (15:41 -0700)]
mac80211: fix ieee80211_queue_stopped()
Johannes Berg notes mac80211 drivers which use
ieee80211_queue_stopped() really only want to know if they
previously requested a queue stop.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marek Puzyniak [Wed, 10 Apr 2013 11:19:13 +0000 (13:19 +0200)]
mac80211: provide SSID in IBSS mode
Some drivers need SSID in AP and IBSS mode. AP SSID is provided
through BSS_CHANGED_SSID notification. There was no easy way to
do the same for IBSS. In IBSS mode SSID is known but was not
stored in BSS configuration. Extend the AP-mode functionality
to also work in IBSS mode.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sun, 7 Apr 2013 17:32:47 +0000 (19:32 +0200)]
mac80211: always advertise STBC/MCSes even if no AP support
Advertise STBC capabilities and MCS rates even if the AP
doesn't support them. This has always been the right thing
to do, but used to be problematic with some APs. Now WFA
testing requires this so re-enable it, problematic APs
would then presumably not pass the test and be fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marek Puzyniak [Wed, 10 Apr 2013 11:47:45 +0000 (13:47 +0200)]
mac80211: clear SSID when stopping AP
When AP interface is stopped ssid_len in the BSS configuration
isn't cleared which can confuse drivers when switching modes.
Set the length to zero when stopping the AP interface.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simon Wunderlich [Mon, 8 Apr 2013 20:43:16 +0000 (22:43 +0200)]
mac80211: fix recalc_radar hwconf sync problem
local->hw.conf maybe not be synced when recalcing whether radar is
enabled, sometimes leaving radar enabled even if it's not neccesary
anymore.
Fix this by:
* setting radar_enabled when creating the chanctx
* turning radar_enabled off before destroying the last channel context
Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Mon, 8 Apr 2013 18:06:16 +0000 (11:06 -0700)]
mac80211: stringify another plink state
The patch "mac80211: stringify mesh peering events" missed
an opportunity to print the peering state as a string.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Mon, 8 Apr 2013 18:06:12 +0000 (11:06 -0700)]
mac80211: unset FC retry bit in mesh fwding path
Otherwise forwarded frames would keep the retry bit set
from the previous link transmission.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Martin Pitt [Mon, 8 Apr 2013 09:30:01 +0000 (11:30 +0200)]
mac80211_hwsim: Register and bind to driver
Properly register our mac80211_hwsim_driver, attach it to the platform bus.
Bind newly created hwsim devices to that driver, so that our wlan devices get
a proper "driver" sysfs attribute.
This makes mac80211_hwsim interfaces work with NetworkManager.
Signed-off-by: Martin Pitt <martin.pitt@ubuntu.com>
[fix an old and a new message to not be line-broken,
also fix the driver_register error path]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Andy Shevchenko [Wed, 10 Apr 2013 11:01:18 +0000 (14:01 +0300)]
ipw2x00: move to kstrto* functions
There is better to use kstrto* instead of simple_strtoul. In this case it
applies a bit stricter rules for input as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Tue, 9 Apr 2013 00:53:21 +0000 (19:53 -0500)]
rtlwifi: rtl8188ee: Fix loop that ends early
In routine _rtl8188e_read_power_value_fromprom(), there are loops initializing
index_cck_base and index_bw40_base from the PROM. As the result of a typo, the
second loop is ended one element too soon.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 7 Apr 2013 22:04:13 +0000 (00:04 +0200)]
ath9k: implement buffer holding handling for EDMA FIFO
Inside one FIFO slot queue, EDMA chipsets have the same link pointer
re-read race condition as older chipsets, so the same buffer holding
logic needs to be used in order to avoid use-after-free bugs.
Unlike on older chips, it can be skipped for the end of the queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 7 Apr 2013 22:04:12 +0000 (00:04 +0200)]
ath9k: detect more kinds of invalid descriptors
If AR_CRCErr, AR_PHYErr, AR_DecryptCRCErr or AR_MichaelErr is indicated
in the rx status word, but AR_RxFrameOK is also set, the descriptor
contents are typically invalid. This can show up as a warning about
invalid MCS rates in a frame. Even with those checks in place, a
descriptor with invalid MCS rates can still sometimes make it through to
the driver (mostly on older hardware like AR91xx).
Detect such errors in the last descriptor of a frame and discard the
whole frame if present.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 7 Apr 2013 22:04:11 +0000 (00:04 +0200)]
ath9k: fix handling of broken descriptors
As the comment in ath_get_next_rx_buf indicates, if a descriptor with
the done bit set follows one with the done bit cleared, both descriptors
should be discarded, however the driver is not doing that yet.
To fix this, use the rs->rs_more flag as an indicator that the following
frame should be discarded. This also helps with the split buffer case:
if the first part of the frame is discarded, the following parts need to
be discarded as well, since they contain no valid header or usable data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 7 Apr 2013 22:04:10 +0000 (00:04 +0200)]
ath9k: improve dma map failure handling
Instead of leaving the buffer without skb and breaking out of the loop
(which could leak the rx buffer), use the common error path.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 7 Apr 2013 22:04:09 +0000 (00:04 +0200)]
ath9k_common: remove ath9k_cmn_padpos
It is equivalent to ieee80211_hdrlen
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 7 Apr 2013 22:04:08 +0000 (00:04 +0200)]
ath9k_hw: make various ar5416/ar91xx rf banks const
Banks 0-3,7 are neither modified at run time, nor SREV dependent.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 7 Apr 2013 22:04:07 +0000 (00:04 +0200)]
ath9k_hw: clean up RF Bank6 handling on AR5416/AR91xx
There are two sets of initvals for this RF bank, one with TPC support and
one without.
The TPC one always gets used, so remove the other one to avoid confusion.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 5 Apr 2013 06:27:05 +0000 (08:27 +0200)]
rt2x00: rt2x00mmio: remove unused rt2x00pci_* defines
All users are converted to use the rt2x00mmio_*
functions so remove the now unused defines.
The patch contain no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 5 Apr 2013 06:27:04 +0000 (08:27 +0200)]
rt2x00: rt2800pci: use the rt2x00mmio_* routines
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 5 Apr 2013 06:27:03 +0000 (08:27 +0200)]
rt2x00: rt61pci: use the rt2x00mmio_* routines
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 5 Apr 2013 06:27:02 +0000 (08:27 +0200)]
rt2x00: rt2500pci: use the rt2x00mmio_* routines
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 5 Apr 2013 06:27:01 +0000 (08:27 +0200)]
rt2x00: rt2400pci: use the rt2x00mmio_* routines
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 5 Apr 2013 06:27:00 +0000 (08:27 +0200)]
rt2x00: rt2x00mmio: use rt2x00mmio prefix in function names
The functions in the rt2x00mmio module has been
moved from the rt2x00pci module. Each function
uses the rt2x00pci prefix which is a bit confusing.
Use the r2x000mmio prefix for each function to make
it consistent with the module name.
The renamed functions are used by several modules,
and updating the names in all of them would result
in a big patch. In order to keep the patch simple,
add compatibility defines for the old function
names. This allows to update the names in each
module separately. After each module is updated,
the defines can be removed.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 10 Apr 2013 18:10:24 +0000 (14:10 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next
John W. Linville [Wed, 10 Apr 2013 18:09:54 +0000 (14:09 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next
Conflicts:
drivers/net/wireless/ath/carl9170/debug.c
drivers/net/wireless/ath/carl9170/main.c
net/mac80211/ieee80211_i.h
John W. Linville [Wed, 10 Apr 2013 13:31:39 +0000 (09:31 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/rt2x00/rt2x00pci.c
Arend van Spriel [Fri, 5 Apr 2013 08:57:54 +0000 (10:57 +0200)]
brcmfmac: only use ifidx from BDC header in brcmf_rx_frames()
In brcmf_rx_frames() the call to brcmf_fweh_process_skb() could
change the ifidx using information in the event data. This is
only different to the BDC ifidx for IF ADD event. However, the
creation of the new interface is deferred to event worker so
it does not exist. After brcmf_fweh_process_skb() it is only
used to set statistics.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:53 +0000 (10:57 +0200)]
brcmfmac: obtain wdev using vif object in action frame rx
The function brcmf_p2p_notify_action_frame_rx() the wireless_dev
is needed to pass the action frame to cfg80211. The wireless_dev
is held in brcmf_cfg80211_vif object. Use that instead of the
ieee80211_ptr in net_device as P2P_DEVICE interface does not have
a net_device associated with it.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:52 +0000 (10:57 +0200)]
brcmfmac: fix reception of P2P probe requests on P2P_DEVICE interface
The probe requests received on P2P_DEVICE interface were not sent
to wpa_supplicant, which makes the device not discoverable by peers.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:51 +0000 (10:57 +0200)]
brcmfmac: wait for firmware event when creating P2P_DEVICE interface
The firmware sends a IF event to notify the host driver that the
P2P_DEVICE interface has been created. Wait for the event before
returning the related wireless_dev.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:50 +0000 (10:57 +0200)]
brcmfmac: support creation of P2P_DEVICE through user-space
The current driver code creates a P2P_DEVICE through a module
parameter. This device has a dummy netdevice which is not how this
interface type is intended. This patch add proper support for the
P2P_DEVICE interface type. This requires a wpa_supplicant with such
support as well.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:49 +0000 (10:57 +0200)]
brcmfmac: use struct brcmf_if instance iso netdevice in escan functions
escan functionality is also required for P2P device operations so it
is better not to rely on struct netdevice instances.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:48 +0000 (10:57 +0200)]
brcmfmac: use struct brcmf_if instance as parameter in brcmf_set_mpc()
Remove use of struct netdevice as parameter to brcmf_set_mpc() as it
will not always be available, ie. there will be non-netdevice interfaces.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:47 +0000 (10:57 +0200)]
brcmfmac: remove use of unconditional access of struct wireless_dev::netdev
With the introduction of the P2P_DEVICE interface type an instance of
struct wireless_dev does not always have a netdev assigned to it. Better
use container_of() construct to obtain internal structure and go from
there.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:46 +0000 (10:57 +0200)]
brcmfmac: remove condition for calling event handler
In fweh module the event handler was only called if the
struct brcmf_if instance had a non-null netdev associated.
This restriction is no longer valid for P2P_DEVICE type
of interface. This patch removes that restriction.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:45 +0000 (10:57 +0200)]
brcmfmac: add role attribute to struct brcmf_if_event definition
According specification the IF event has an additional field indicating
the role or type of the interface for which this event is sent.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:44 +0000 (10:57 +0200)]
brcmfmac: add hexadecimal trace of message payload
Adds a trace function used in brcmf_dbg_hex_dump() which adds the
raw binary data to the trace. It requires trace-cmd plugin to see
this data.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piotr Haber [Fri, 5 Apr 2013 08:57:43 +0000 (10:57 +0200)]
brcmfmac: firmware shared data version fix
Firware shared data structure is backward compatible for fields
we are interested in.
Allow reading of shared data in case of version mismatch.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piotr Haber [Fri, 5 Apr 2013 08:57:42 +0000 (10:57 +0200)]
brcmfmac: read firmware console without trap indication
Firmware console output can be read also when there was
no trap indication.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:41 +0000 (10:57 +0200)]
brcmfmac: handle firmware signals requesting for packets
The firmware can request the host driver for packets, by sending
either the MAC_REQUEST_CREDIT or the MAC_REQUEST_PACKET primitive.
This patch adds handling of these primitives.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:40 +0000 (10:57 +0200)]
brcmfmac: handle firmware signalling destination entry state
Firmware can signal whether the host driver may sent packets for
a specific destination or interface. This can happen when a
destination is sleeping or when going off-channel.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 5 Apr 2013 08:57:39 +0000 (10:57 +0200)]
brcmfmac: fix unaligned access in TXSTATUS signal handling
reported by Hante. Needs to be squashed in commit
187fbcec.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andreas Fenkart [Fri, 5 Apr 2013 03:03:53 +0000 (20:03 -0700)]
mwifiex: hold proper locks when accessing ra_list / bss_prio lists
Not locking ra_list when dequeuing packets creates race conditions.
When adding a packet 'tx_pkts_queued' is modified before setting
highest_priority_queue. If in-between the main loop starts, it will
see a packet queued (tx_pkts_queued > 0) but will not find it, since
max prio is not set yet. Depending on the scheduling, the thread
trying to add the packet could complete and restore the situation.
But this is not something to rely on.
Another race condition exists, if a new packet, exceeding current
max prio is added. If concurrently a packet is dequeued, the newly
set max prio will be overwritten with the value of the dequeued
packet. This can occur, because selecting a packet and modifying
the max prio is not atomic. The result in an infinite loop unless,
a new packet is added that has at least the priority of the hidden
packet.
Same applies to bss_prio_tbl. Forward iteration is no proper
lock-free technique and provides no protection from calls to
list_del. Although BSS are currently not added/removed dynamically,
this must not be the case in the future. Hence always hold proper
locks when accessing those lists.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andreas Fenkart [Fri, 5 Apr 2013 03:03:52 +0000 (20:03 -0700)]
mwifiex: fix infinite loop by removing NO_PKT_PRIO_TID
Using NO_PKT_PRIO_TID and tx_pkts_queued to check for an empty
state, can lead to a contradictory state, resulting in an
infinite loop. Currently queueing and dequeuing of packets is
not synchronized, and can happen concurrently. While tx_pkts_queued
is incremented when adding a packet, max prio is set to NO_PKT when
the WMM list is empty. If a packet is added right after the check
for empty, but before setting max prio to NO_PKT, that packet is
trapped and creates an infinite loop.
Because of the new packet, tx_pkts_queued is at least 1, indicating
wmm lists are not empty. Opposing that max prio is NO_PKT, which
means "skip this wmm queue, it has no packets". The infinite loop
results, because the main loop checks the wmm lists for not empty
via tx_pkts_queued, but for dequeing it uses max_prio to see if it
can skip current list. This will never end, unless a new packet is
added which will restore max prio to the level of the trapped packet.
The solution here is to rely on tx_pkts_queued solely for checking
wmm queue to be empty, and drop the NO_PKT define. It does not
address the locking issue.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andreas Fenkart [Fri, 5 Apr 2013 03:03:51 +0000 (20:03 -0700)]
mwifiex: remove unused tid_tbl_lock from mwifiex_tid_tbl
ra_list_spinlock is used to protect struct mwifiex_wmm_desc and
embedded structures such as ra_list. tid_tbl_lock while more fine
grained, is not used but in one function. That function is not
called reentrantly. To protect ra_list from concurrent modification
ra_list_spinlock must be held.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andreas Fenkart [Fri, 5 Apr 2013 03:03:50 +0000 (20:03 -0700)]
mwifiex: correct wrong list in list_empty check
adapter->bss_prio_tbl list has already been checked in outer loop.
The inner loop works with priv_tmp->wmm.tid_tbl_ptr list. Also the
lock taken, gives hint that this is likely a copy-paste error.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 4 Apr 2013 19:41:06 +0000 (14:41 -0500)]
rtlwifi: rtl8188ee: Fix allyesconfig build failures
An allyesconfig build of rtl8188ee yields the following duplicate entry points:
drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `.rtl92c_phy_ap_calibrate':
(.text+0x21d14): multiple definition of `.rtl92c_phy_ap_calibrate'
drivers/net/wireless/rtlwifi/rtl8192c/built-in.o:(.text+0xb1e8): first defined here
drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `rtl_hal_pwrseqcmdparsing':
(.opd+0xed0): multiple definition of `rtl_hal_pwrseqcmdparsing'
One of the routines is not used and can be deleted, the other is renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 4 Apr 2013 01:36:06 +0000 (20:36 -0500)]
rtlwifi: rtl8188ee: Fix linker warnings
Building rtl8188ee yields warnings such as the following:
x86_64-linux-gcc: warning: drivers/net/wireless/rtlwifi: linker input file unused because linking not done
The only potential cause is an extraneous space in the make file.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zefir Kurtisi [Wed, 3 Apr 2013 16:31:31 +0000 (18:31 +0200)]
ath9k: add support for DFS master mode
These are the remaining knobs in ath9k to support DFS:
* mark AR9280 and AR9580 as DFS tested
* synchronize DFS regulatory domain to reg notifyer
* set required RX filter flags for radar detection
* process radar PHY errors at DFS detector
* notify DFS master on radar detection
DFS support requires CONFIG_ATH9K_DFS_CERTIFIED to be set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zefir Kurtisi [Wed, 3 Apr 2013 16:31:30 +0000 (18:31 +0200)]
ath9k: add debugfs based DFS radar simulation
This helps testing DFS without radar generating
equipment and is required for certification.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zefir Kurtisi [Wed, 3 Apr 2013 16:31:29 +0000 (18:31 +0200)]
ath9k: add interface combinations for DFS master
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Mon, 1 Apr 2013 22:37:29 +0000 (15:37 -0700)]
ath: Let user know which keycache method is complaining.
Should make the warning messages more useful.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Mon, 1 Apr 2013 19:44:46 +0000 (12:44 -0700)]
mwifiex: fix negative cmd_pending count
cmd_pending is increased in mwifiex_wait_queue_complete() and
decreased in mwifiex_complete_cmd() currently.
If there are two or more commands in the cmd_pending_q the main
worker thread will pick up next command from cmd_pending_q
automatically after finishing current command. As a result
mwifiex_wait_queue_complete() will not be called because
the command is alreay completed. This leads to a negative
number in cmd_pending count.
Fix it by increasing cmd_pending when a cmd is queued into
cmd_pending_q and decreasing when that cmd is recycled. For scan
commands we don't perform inc/dec operations until it's moved
from scan_pending_q to cmd_pending_q. This covers both
synchronous and asynchronous commands.
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Sun, 7 Apr 2013 07:13:44 +0000 (10:13 +0300)]
iwlwifi: dvm: handle FLUSH ampdu actions from mac80211
Until now we didn't handle properly the FLUSH ampdu action
coming from mac80211. This could result in SCD queue leak:
mac80211 would STOP_FLUSH an AMPDU Tx session and remove
the station. If we had still packets on the ring, we
wouldn't deallocate the SCD queue and wait for it to be
empty.
The indication of the queue being empty comes from the Tx
response flow which relies on the tid_data structure. The
problem is that this structure has been cleared when the
station has been removed.
In order to solve this issue, block in the STOP_FLUSH
ampdu_action until the SCD queue is flushed, and only then,
let mac80211 move forward to remove the station.
iwlagn_txfifo_flush had to be enhanced to allow this.
The bug fixed here caused the "txq_id mismatch: 12 0" print.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Wed, 3 Apr 2013 17:10:06 +0000 (20:10 +0300)]
iwlwifi: mvm: remove users of nvm_data->valid_tx_ant
In commit
332235427a566d8be04b9676a7ac380c8853aa9b
"iwlwifi: mvm: take the valid_{rx,tx}_ant from the TLV"
I replaced the access to nvm_data->valid_tx_ant to an inline
cheking the TLV flags but forgot a few occurences. Fix that.
Change-Id: I92daac735b46738d97fe2dbd5934bb177fd0751b
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/12308
Tested-by: IWL Jenkins
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 4 Apr 2013 08:35:23 +0000 (10:35 +0200)]
iwlwifi: print warning on request_module failure
If request_module() failed then we didn't have the correct
opmode module that the driver needs to function, so print
a warning in this case to make it more obvious what could
be wrong. This still won't catch the case where the module
simply doesn't exist because it wasn't compiled though.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 27 Mar 2013 13:55:31 +0000 (14:55 +0100)]
mac80211: make ieee802_11_parse_elems an inline
This (slightly) reduces the code size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 26 Mar 2013 21:23:20 +0000 (22:23 +0100)]
mac80211: don't start new netdev queues if driver stopped
If a new netdev (e.g. an AP VLAN) is created while the driver
has queues stopped, the new netdev queues will be started even
though they shouldn't. This will lead to frames accumulating
on the internal mac80211 pending queues instead of properly
being held on the netdev queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 26 Mar 2013 21:10:02 +0000 (22:10 +0100)]
mac80211: replace some dead code by a warning
Given the (nested) switch statements, this code can't
be reached, so make it warn instead of manipulating
the carrier state which seems purposeful.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>