OSDN Git Service
Arkadi Sharshevsky [Mon, 25 Sep 2017 08:32:28 +0000 (10:32 +0200)]
mlxsw: spectrum: Add support for setting counters on nexthops
Add support for setting counters on nexthops based on dpipe's adjacency
table counter status. This patch also adds the ability for getting the
counter value, which will be used by the dpipe adjacency table dump
implementation in the next patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Mon, 25 Sep 2017 08:32:27 +0000 (10:32 +0200)]
mlxsw: reg: Add support for counters on RATR
In order to add the ability for setting counters on nexthops the RATR
register should be extended.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Mon, 25 Sep 2017 08:32:26 +0000 (10:32 +0200)]
mlxsw: spectrum_dpipe: Add initial support for the router adjacency table
Add initial support for router adjacency table. The table does lookup
based on the nexthop-group index and the local nexthop offset. After
locating the nexthop entry it sets the destination MAC address and the
egress RIF.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Mon, 25 Sep 2017 08:32:25 +0000 (10:32 +0200)]
mlxsw: spectrum_router: Add helpers for nexthop access
This is done as a preparation before introducing the ability to dump the
adjacency table via dpipe, and to count the table size. The current table
implementation avoids tunnel entries, thus a helper for checking if
the nexthop group contains tunnel entries is also provided. The mlxsw's
nexthop representative struct stays private to the router module.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Mon, 25 Sep 2017 08:32:24 +0000 (10:32 +0200)]
mlxsw: spectrum_router: Use helper to check for last neighbor
Use list_is_last helper to check for last neighbor.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Mon, 25 Sep 2017 08:32:23 +0000 (10:32 +0200)]
mlxsw: spectrum_router: Keep nexthops in a linked list
Keep nexthops in a linked list for easy access.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Mon, 25 Sep 2017 08:32:22 +0000 (10:32 +0200)]
mlxsw: Add fields for mlxsw's meta header for adjacency table
This patch adds field for mlxsw's meta header which will be used to
describe the match/action behavior of the adjacency table.
The fields are:
1. Adj_index - The global index of the nexthop group in the adjacency
table.
2. Adj_hash_index - Local index offset which is based on packets hash
mod the nexthop group size.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arkadi Sharshevsky [Mon, 25 Sep 2017 08:32:21 +0000 (10:32 +0200)]
mlxsw: spectrum_dpipe: Fix indentation in header description
Fix indentation in mlxsw_meta header's description.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 26 Sep 2017 20:36:45 +0000 (13:36 -0700)]
Merge branch 'bpf-metadata-direct-access'
Daniel Borkmann says:
====================
BPF metadata for direct access
This work enables generic transfer of metadata from XDP into skb,
meaning the packet has a flexible and programmable room for meta
data, which can later be used by BPF to set various skb members
when passing up the stack. For details, please see second patch.
Support has been implemented and tested with two drivers, and
should be straight forward to add to other drivers as well which
properly support head adjustment already.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 25 Sep 2017 00:25:55 +0000 (02:25 +0200)]
bpf, ixgbe: add meta data support
Implement support for transferring XDP meta data into skb for
ixgbe driver; before calling into the program, xdp.data_meta points
to xdp.data, where on program return with pass verdict, we call
into skb_metadata_set().
We implement this for the default ixgbe_build_skb() variant. For the
ixgbe_construct_skb() that is used when legacy-rx buffer mananagement
mode is turned on via ethtool, I found that XDP gets 0 headroom, so
neither xdp_adjust_head() nor xdp_adjust_meta() can be used with this.
Just add a comment with explanation for this operating mode.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 25 Sep 2017 00:25:54 +0000 (02:25 +0200)]
bpf, nfp: add meta data support
Implement support for transferring XDP meta data into skb for
nfp driver; before calling into the program, xdp.data_meta points
to xdp.data, where on program return with pass verdict, we call
into skb_metadata_set().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 25 Sep 2017 00:25:53 +0000 (02:25 +0200)]
bpf: improve selftests and add tests for meta pointer
Add various test_verifier selftests, and a simple xdp/tc functional
test that is being attached to veths. Also let new versions of clang
use the recently added -mcpu=probe support [1] for the BPF target,
so that it can probe the underlying kernel for BPF insn set extensions.
We could also just set this options always, where older versions just
ignore it and give a note to the user that the -mcpu value is not
supported, but given emitting the note cannot be turned off from clang
side lets not confuse users running selftests with it, thus fallback
to the default generic one when we see that clang doesn't support it.
Also allow CPU option to be overridden in the Makefile from command
line.
[1] https://github.com/llvm-mirror/llvm/commit/
d7276a40d87b89aed89978dec6457a5b8b3a0db5
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 25 Sep 2017 00:25:52 +0000 (02:25 +0200)]
bpf: update bpf.h uapi header for tools
Looks like a couple of updates missed to get carried into tools/include/uapi/,
so copy the bpf.h header as usual to pull in latest updates.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 25 Sep 2017 00:25:51 +0000 (02:25 +0200)]
bpf: add meta pointer for direct access
This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.
xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.
The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 25 Sep 2017 00:25:50 +0000 (02:25 +0200)]
bpf: rename bpf_compute_data_end into bpf_compute_data_pointers
Just do the rename into bpf_compute_data_pointers() as we'll add
one more pointer here to recompute.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Jha [Sun, 24 Sep 2017 12:11:24 +0000 (17:41 +0530)]
net: bcm63xx_enet: Use setup_timer and mod_timer
Use setup_timer and mod_timer API instead of structure assignments.
This is done using Coccinelle and semantic patch used
for this as follows:
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 26 Sep 2017 18:22:03 +0000 (11:22 -0700)]
Merge branch 'qed-iWARP-fixes-and-enhancements'
Michal Kalderon says:
====================
qed: iWARP fixes and enhancements
This patch series includes several fixes and enhancements
related to iWARP.
Patch #1 is actually the last of the initial iWARP submission.
It has been delayed until now as I wanted to make sure that qedr
supports iWARP prior to enabling iWARP device detection.
iWARP changes in RDMA tree have been accepted and targeted at
kernel 4.15, therefore, all iWARP fixes for this cycle are
submitted to net-next.
Changes from v1->v2
- Added "Fixes:" tag to commit message of patch #3
====================
Signed-off by: Michal.Kalderon@cavium.com
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Sun, 24 Sep 2017 09:09:45 +0000 (12:09 +0300)]
qed: iWARP - Add check for errors on a SYN packet
A SYN packet which arrives with errors from FW should be dropped.
This required adding an additional field to the ll2
rx completion data.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Sun, 24 Sep 2017 09:09:44 +0000 (12:09 +0300)]
qed: Fix maximum number of CQs for iWARP
The maximum number of CQs supported is bound to the number
of connections supported, which differs between RoCE and iWARP.
This fixes a crash that occurred in iWARP when running 1000 sessions
using perftest.
Fixes:
67b40dccc45 ("qed: Implement iWARP initialization, teardown and qp operations")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Sun, 24 Sep 2017 09:09:43 +0000 (12:09 +0300)]
qed: Add iWARP out of order support
iWARP requires OOO support which is already provided by the ll2
interface (until now was used only for iSCSI offload).
The changes mostly include opening a ll2 dedicated connection for
OOO and notifiying the FW about the handle id.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Sun, 24 Sep 2017 09:09:42 +0000 (12:09 +0300)]
qed: Add iWARP enablement support
This patch is the last of the initial iWARP patch series. It
adds the possiblity to actually detect iWARP from the device and enable
it in the critical locations which basically make iWARP available.
It wasn't submitted until now as iWARP hadn't been accepted into
the rdma tree.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 26 Sep 2017 13:14:15 +0000 (15:14 +0200)]
ldmvsw: Remove redundant unlikely()
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 26 Sep 2017 13:13:23 +0000 (15:13 +0200)]
net/mlx5: Remove redundant unlikely()
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 26 Sep 2017 13:12:26 +0000 (15:12 +0200)]
bnxt_en: Remove redundant unlikely()
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 26 Sep 2017 09:22:58 +0000 (11:22 +0200)]
kcm: Remove redundant unlikely()
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 26 Sep 2017 09:22:31 +0000 (11:22 +0200)]
ipv6: Remove redundant unlikely()
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 26 Sep 2017 09:21:42 +0000 (11:21 +0200)]
datagram: Remove redundant unlikely()
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 26 Sep 2017 09:04:23 +0000 (11:04 +0200)]
net: ena: Remove redundant unlikely()
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Sat, 23 Sep 2017 20:03:04 +0000 (23:03 +0300)]
neigh: make strucrt neigh_table::entry_size unsigned int
Key length can't be negative.
Leave comparisons against nla_len() signed just in case truncated attribute
can sneak in there.
Space savings:
add/remove: 0/0 grow/shrink: 0/7 up/down: 0/-7 (-7)
function old new delta
pneigh_delete 273 272 -1
mlx5e_rep_netevent_event 1415 1414 -1
mlx5e_create_encap_header_ipv6 1194 1193 -1
mlx5e_create_encap_header_ipv4 1071 1070 -1
cxgb4_l2t_get 1104 1103 -1
__pneigh_lookup 69 68 -1
__neigh_create 2452 2451 -1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Sat, 23 Sep 2017 20:01:06 +0000 (23:01 +0300)]
neigh: make struct neigh_table::entry_size unsigned int
Neigh entry size can't be negative.
Space savings:
add/remove: 0/0 grow/shrink: 0/5 up/down: 0/-7 (-7)
function old new delta
lowpan_neigh_construct 25 24 -1
clip_seq_sub_iter 152 151 -1
clip_ioctl 1475 1474 -1
clip_constructor 93 92 -1
__neigh_create 2455 2452 -3
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 23 Sep 2017 19:39:12 +0000 (12:39 -0700)]
net: speed up skb_rbtree_purge()
As measured in my prior patch ("sch_netem: faster rb tree removal"),
rbtree_postorder_for_each_entry_safe() is nice looking but much slower
than using rb_next() directly, except when tree is small enough
to fit in CPU caches (then the cost is the same)
Also note that there is not even an increase of text size :
$ size net/core/skbuff.o.before net/core/skbuff.o
text data bss dec hex filename
40711 1298 0 42009 a419 net/core/skbuff.o.before
40711 1298 0 42009 a419 net/core/skbuff.o
From: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 23 Sep 2017 18:07:28 +0000 (11:07 -0700)]
sch_netem: faster rb tree removal
While running TCP tests involving netem storing millions of packets,
I had the idea to speed up tfifo_reset() and did experiments.
I tried the rbtree_postorder_for_each_entry_safe() method that is
used in skb_rbtree_purge() but discovered it was slower than the
current tfifo_reset() method.
I measured time taken to release skbs with three occupation levels :
10^4, 10^5 and 10^6 skbs with three methods :
1) (current 'naive' method)
while ((p = rb_first(&q->t_root))) {
struct sk_buff *skb = netem_rb_to_skb(p);
rb_erase(p, &q->t_root);
rtnl_kfree_skbs(skb, skb);
}
2) Use rb_next() instead of rb_first() in the loop :
p = rb_first(&q->t_root);
while (p) {
struct sk_buff *skb = netem_rb_to_skb(p);
p = rb_next(p);
rb_erase(&skb->rbnode, &q->t_root);
rtnl_kfree_skbs(skb, skb);
}
3) "optimized" method using rbtree_postorder_for_each_entry_safe()
struct sk_buff *skb, *next;
rbtree_postorder_for_each_entry_safe(skb, next,
&q->t_root, rbnode) {
rtnl_kfree_skbs(skb, skb);
}
q->t_root = RB_ROOT;
Results :
method_1:while (rb_first()) rb_erase() 10000 skbs in 690378 ns (69 ns per skb)
method_2:rb_first; while (p) { p = rb_next(p); ...} 10000 skbs in 541846 ns (54 ns per skb)
method_3:rbtree_postorder_for_each_entry_safe() 10000 skbs in 868307 ns (86 ns per skb)
method_1:while (rb_first()) rb_erase() 99996 skbs in
7804021 ns (78 ns per skb)
method_2:rb_first; while (p) { p = rb_next(p); ...} 100000 skbs in
5942456 ns (59 ns per skb)
method_3:rbtree_postorder_for_each_entry_safe() 100000 skbs in
11584940 ns (115 ns per skb)
method_1:while (rb_first()) rb_erase()
1000000 skbs in
108577838 ns (108 ns per skb)
method_2:rb_first; while (p) { p = rb_next(p); ...}
1000000 skbs in
82619635 ns (82 ns per skb)
method_3:rbtree_postorder_for_each_entry_safe()
1000000 skbs in
127328743 ns (127 ns per skb)
Method 2) is simply faster, probably because it maintains a smaller
working size set.
Note that this is the method we use in tcp_ofo_queue() already.
I will also change skb_rbtree_purge() in a second patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
yuan linyu [Sat, 23 Sep 2017 14:36:52 +0000 (22:36 +0800)]
tun: delete original tun_get() and rename __tun_get() to tun_get()
it seems no need to keep tun_get() and __tun_get() at same time.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Sat, 23 Sep 2017 10:37:28 +0000 (16:07 +0530)]
cxgb4: do DCB state reset in couple of places
reset the driver's DCB state in couple of places
where it was missing.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 26 Sep 2017 03:25:40 +0000 (20:25 -0700)]
Merge branch 'liquidio-fw-loading'
Rick Farrington says:
====================
liquidio: firmware loading
1. Allow host driver parameter to override auto-loaded firmware (in flash).
2. Verify version of firmware that is auto-loaded from flash.
3. Change value of fw_type module parameter to reflect default firmware
image name that is loaded by host driver (in /sys/module/liquidio/...)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Farrington [Sat, 23 Sep 2017 00:12:51 +0000 (17:12 -0700)]
liquidio: update module parameter fw_type to reflect firmware type loaded
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Farrington [Sat, 23 Sep 2017 00:12:47 +0000 (17:12 -0700)]
liquidio: verify firmware version when auto-loaded from flash.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rick Farrington [Sat, 23 Sep 2017 00:12:43 +0000 (17:12 -0700)]
liquidio: allow override of firmware present in flash
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 26 Sep 2017 03:22:46 +0000 (20:22 -0700)]
Merge branch 'dsa-port-enabling'
Vivien Didelot says:
====================
net: dsa: port enabling
This patchset makes slave open and close symmetrical and provides
helpers for enabling or disabling a given DSA port.
Changes in v3:
- save the phy_device change for a future patchset
Changes in v2:
- do not remove the phy argument from port enable/disable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 22 Sep 2017 23:01:56 +0000 (19:01 -0400)]
net: dsa: add port enable and disable helpers
Provide dsa_port_enable and dsa_port_disable helpers to respectively
enable and disable a switch port. This makes the dsa_port_set_state_now
helper static.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 22 Sep 2017 23:01:55 +0000 (19:01 -0400)]
net: dsa: make slave close symmetrical to open
The DSA slave open function configures the unicast MAC addresses on the
master device, enable the switch port, change its STP state, then start
the PHY device.
Make the close function symmetric, by first stopping the PHY device,
then changing the STP state, disabling the switch port and restore the
master device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 22 Sep 2017 22:31:38 +0000 (15:31 -0700)]
hv_netvsc: Fix the real number of queues of non-vRSS cases
For older hosts without multi-channel (vRSS) support, and some error
cases, we still need to set the real number of queues to one.
This patch adds this missing setting.
Fixes:
8195b1396ec8 ("hv_netvsc: fix deadlock on hotplug")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 26 Sep 2017 03:16:14 +0000 (20:16 -0700)]
Merge branch 'tun-NAPI-and-gro'
Petar Penkov says:
====================
net: Improve code coverage of syzkaller
This patch series is intended to improve code coverage of syzkaller on
the early receive path, specifically including flow dissector, GRO,
and GRO with frags parts of the networking stack. Syzkaller exercises
the stack through the TUN driver and this is therefore where changes
reside. Current coverage through netif_receive_skb() is limited as it
does not touch on any of the aforementioned code paths. Furthermore,
for full coverage, it is necessary to have more flexibility over the
linear and non-linear data of the skbs.
The following patches address this by providing the user(syzkaller)
with the ability to send via napi_gro_receive() and napi_gro_frags().
Additionally, syzkaller can specify how many fragments there are and
how much data per fragment there is. This is done by exploiting the
convenient structure of iovecs. Finally, this patch series adds
support for exercising the flow dissector during fuzzing.
The code path including napi_gro_receive() can be enabled via the
IFF_NAPI flag. The remainder of the changes in this patch series give
the user significantly more control over packets entering the kernel.
To avoid potential security vulnerabilities, hide the ability to send
custom skbs and the flow dissector code paths behind a
capable(CAP_NET_ADMIN) check to require special user privileges.
Changes since v2 based on feedback from Willem de Bruijn and Mahesh
Bandewar:
Patch 1/ No changes.
Patch 2/ Check if the preconditions for IFF_NAPI_FRAGS (IFF_NAPI and
IFF_TAP) are met before opening/attaching rather than after.
If they are not, change the behavior from discarding the
flag to rejecting the command with EINVAL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petar Penkov [Fri, 22 Sep 2017 20:49:15 +0000 (13:49 -0700)]
tun: enable napi_gro_frags() for TUN/TAP driver
Add a TUN/TAP receive mode that exercises the napi_gro_frags()
interface. This mode is available only in TAP mode, as the interface
expects packets with Ethernet headers.
Furthermore, packets follow the layout of the iovec_iter that was
received. The first iovec is the linear data, and every one after the
first is a fragment. If there are more fragments than the max number,
drop the packet. Additionally, invoke eth_get_headlen() to exercise flow
dissector code and to verify that the header resides in the linear data.
The napi_gro_frags() mode requires setting the IFF_NAPI_FRAGS option.
This is imposed because this mode is intended for testing via tools like
syzkaller and packetdrill, and the increased flexibility it provides can
introduce security vulnerabilities. This flag is accepted only if the
device is in TAP mode and has the IFF_NAPI flag set as well. This is
done because both of these are explicit requirements for correct
operation in this mode.
Signed-off-by: Petar Penkov <peterpenkov96@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: davem@davemloft.net
Cc: ppenkov@stanford.edu
Acked-by: Mahesh Bandewar <maheshb@google,com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petar Penkov [Fri, 22 Sep 2017 20:49:14 +0000 (13:49 -0700)]
tun: enable NAPI for TUN/TAP driver
Changes TUN driver to use napi_gro_receive() upon receiving packets
rather than netif_rx_ni(). Adds flag IFF_NAPI that enables these
changes and operation is not affected if the flag is disabled. SKBs
are constructed upon packet arrival and are queued to be processed
later.
The new path was evaluated with a benchmark with the following setup:
Open two tap devices and a receiver thread that reads in a loop for
each device. Start one sender thread and pin all threads to different
CPUs. Send 1M minimum UDP packets to each device and measure sending
time for each of the sending methods:
napi_gro_receive(): 4.90s
netif_rx_ni(): 4.90s
netif_receive_skb(): 7.20s
Signed-off-by: Petar Penkov <peterpenkov96@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: davem@davemloft.net
Cc: ppenkov@stanford.edu
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Shengju [Fri, 22 Sep 2017 15:57:49 +0000 (23:57 +0800)]
net: remove MTU limits for dummy and ifb device
These two drivers (dummy and ifb) call ether_setup(), after commit
61e84623ace3 ("net: centralize net_device min/max MTU checking"), the
range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default.
These two devices should not have limits on MTU. This patch set their
min_mtu/max_mtu to 0. So that dev_set_mtu() will not check the mtu range,
and can be set with any value.
CC: Eric Dumazet <edumazet@google.com>
CC: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 22 Sep 2017 15:50:23 +0000 (16:50 +0100)]
hv_netvsc: make const array ver_list static, reduces object code size
Don't populate const array ver_list on the stack, instead make it
static. Makes the object code smaller by over 400 bytes:
Before:
text data bss dec hex filename
18444 3168 320 21932 55ac drivers/net/hyperv/netvsc.o
After:
text data bss dec hex filename
17950 3224 320 21494 53f6 drivers/net/hyperv/netvsc.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Craig Gallek [Thu, 21 Sep 2017 22:43:29 +0000 (18:43 -0400)]
bpf: Optimize lpm trie delete
Before the delete operator was added, this datastructure maintained
an invariant that intermediate nodes were only present when necessary
to build the tree. This patch updates the delete operation to reinstate
that invariant by removing unnecessary intermediate nodes after a node is
removed and thus keeping the tree structure at a minimal size.
Suggested-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allen Pais [Mon, 25 Sep 2017 07:30:05 +0000 (13:00 +0530)]
net: nfc: llcp_core: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allen Pais [Mon, 25 Sep 2017 07:30:04 +0000 (13:00 +0530)]
net: nfc: hci: llc_shdlc: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allen Pais [Mon, 25 Sep 2017 07:30:03 +0000 (13:00 +0530)]
net: nfc: hci: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allen Pais [Mon, 25 Sep 2017 07:30:02 +0000 (13:00 +0530)]
net: af_packet: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yanjun [Fri, 22 Sep 2017 14:20:21 +0000 (10:20 -0400)]
forcedeth: optimize the xmit/rx with unlikely
In the xmit/rx fastpath, the function dma_map_single rarely fails.
Therefore, add an unlikely() optimization to this error check
conditional.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 23 Sep 2017 17:16:53 +0000 (10:16 -0700)]
Merge git://git./linux/kernel/git/davem/net
Linus Torvalds [Sat, 23 Sep 2017 16:14:06 +0000 (06:14 -1000)]
Merge branch 'parisc-4.14-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Unbreak parisc bootloader by avoiding a gcc-7 optimization to convert
multiple byte-accesses into one word-access.
- Add missing HWPOISON page fault handler code. I completely missed
that when I added HWPOISON support during this merge window and it
only showed up now with the madvise07 LTP test case.
- Fix backtrace unwinding to stop when stack start has been reached.
- Issue warning if initrd has been loaded into memory regions with
broken RAM modules.
- Fix HPMC handler (parisc hardware fault handler) to comply with
architecture specification.
- Avoid compiler warnings about too large frame sizes.
- Minor init-section fixes.
* 'parisc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Unbreak bootloader due to gcc-7 optimizations
parisc: Reintroduce option to gzip-compress the kernel
parisc: Add HWPOISON page fault handler code
parisc: Move init_per_cpu() into init section
parisc: Check if initrd was loaded into broken RAM
parisc: Add PDCE_CHECK instruction to HPMC handler
parisc: Add wrapper for pdc_instr() firmware function
parisc: Move start_parisc() into init section
parisc: Stop unwinding at start of stack
parisc: Fix too large frame size warnings
Linus Torvalds [Sat, 23 Sep 2017 15:47:04 +0000 (05:47 -1000)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
- Smattering of miscellanous fixes
- A five patch series for i40iw that had a patch (5/5) that was larger
than I would like, but I took it because it's needed for large scale
users
- An 8 patch series for bnxt_re that landed right as I was leaving on
PTO and so had to wait until now...they are all appropriate fixes for
-rc IMO
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (22 commits)
bnxt_re: Don't issue cmd to delete GID for QP1 GID entry before the QP is destroyed
bnxt_re: Fix memory leak in FRMR path
bnxt_re: Remove RTNL lock dependency in bnxt_re_query_port
bnxt_re: Fix race between the netdev register and unregister events
bnxt_re: Free up devices in module_exit path
bnxt_re: Fix compare and swap atomic operands
bnxt_re: Stop issuing further cmds to FW once a cmd times out
bnxt_re: Fix update of qplib_qp.mtu when modified
i40iw: Add support for port reuse on active side connections
i40iw: Add missing VLAN priority
i40iw: Call i40iw_cm_disconn on modify QP to disconnect
i40iw: Prevent multiple netdev event notifier registrations
i40iw: Fail open if there are no available MSI-X vectors
RDMA/vmw_pvrdma: Fix reporting correct opcodes for completion
IB/bnxt_re: Fix frame stack compilation warning
IB/mlx5: fix debugfs cleanup
IB/ocrdma: fix incorrect fall-through on switch statement
IB/ipoib: Suppress the retry related completion errors
iw_cxgb4: remove the stid on listen create failure
iw_cxgb4: drop listen destroy replies if no ep found
...
Linus Torvalds [Sat, 23 Sep 2017 15:41:27 +0000 (05:41 -1000)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix NAPI poll list corruption in enic driver, from Christian
Lamparter.
2) Fix route use after free, from Eric Dumazet.
3) Fix regression in reuseaddr handling, from Josef Bacik.
4) Assert the size of control messages in compat handling since we copy
it in from userspace twice. From Meng Xu.
5) SMC layer bug fixes (missing RCU locking, bad refcounting, etc.)
from Ursula Braun.
6) Fix races in AF_PACKET fanout handling, from Willem de Bruijn.
7) Don't use ARRAY_SIZE on spinlock array which might have zero
entries, from Geert Uytterhoeven.
8) Fix miscomputation of checksum in ipv6 udp code, from Subash Abhinov
Kasiviswanathan.
9) Push the ipv6 header properly in ipv6 GRE tunnel driver, from Xin
Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
inet: fix improper empty comparison
net: use inet6_rcv_saddr to compare sockets
net: set tb->fast_sk_family
net: orphan frags on stand-alone ptype in dev_queue_xmit_nit
MAINTAINERS: update git tree locations for ieee802154 subsystem
net: prevent dst uses after free
net: phy: Fix truncation of large IRQ numbers in phy_attached_print()
net/smc: no close wait in case of process shut down
net/smc: introduce a delay
net/smc: terminate link group if out-of-sync is received
net/smc: longer delay for client link group removal
net/smc: adapt send request completion notification
net/smc: adjust net_device refcount
net/smc: take RCU read lock for routing cache lookup
net/smc: add receive timeout check
net/smc: add missing dev_put
net: stmmac: Cocci spatch "of_table"
lan78xx: Use default values loaded from EEPROM/OTP after reset
lan78xx: Allow EEPROM write for less than MAX_EEPROM_SIZE
lan78xx: Fix for eeprom read/write when device auto suspend
...
Linus Torvalds [Sat, 23 Sep 2017 15:33:29 +0000 (05:33 -1000)]
Merge tag 'apparmor-pr-2017-09-22' of git://git./linux/kernel/git/jj/linux-apparmor
Pull apparmor updates from John Johansen:
"This is the apparmor pull request, similar to SELinux and seccomp.
It's the same series that I was sent to James' security tree + one
regression fix that was found after the series was sent to James and
would have been sent for v4.14-rc2.
Features:
- in preparation for secid mapping add support for absolute root view
based labels
- add base infastructure for socket mediation
- add mount mediation
- add signal mediation
minor cleanups and changes:
- be defensive, ensure unconfined profiles have dfas initialized
- add more debug asserts to apparmorfs
- enable policy unpacking to audit different reasons for failure
- cleanup conditional check for label in label_print
- Redundant condition: prev_ns. in [label.c:1498]
Bug Fixes:
- fix regression in apparmorfs DAC access permissions
- fix build failure on sparc caused by undeclared signals
- fix sparse report of incorrect type assignment when freeing label proxies
- fix race condition in null profile creation
- Fix an error code in aafs_create()
- Fix logical error in verify_header()
- Fix shadowed local variable in unpack_trans_table()"
* tag 'apparmor-pr-2017-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: fix apparmorfs DAC access permissions
apparmor: fix build failure on sparc caused by undeclared signals
apparmor: fix incorrect type assignment when freeing proxies
apparmor: ensure unconfined profiles have dfas initialized
apparmor: fix race condition in null profile creation
apparmor: move new_null_profile to after profile lookup fns()
apparmor: add base infastructure for socket mediation
apparmor: add more debug asserts to apparmorfs
apparmor: make policy_unpack able to audit different info messages
apparmor: add support for absolute root view based labels
apparmor: cleanup conditional check for label in label_print
apparmor: add mount mediation
apparmor: add the ability to mediate signals
apparmor: Redundant condition: prev_ns. in [label.c:1498]
apparmor: Fix an error code in aafs_create()
apparmor: Fix logical error in verify_header()
apparmor: Fix shadowed local variable in unpack_trans_table()
David S. Miller [Sat, 23 Sep 2017 04:29:10 +0000 (21:29 -0700)]
Merge branch 'ieee802154-for-davem-2017-09-20' of git://git./linux/kernel/git/sschmidt/wpan-next
Stefan Schmidt says:
====================
pull-request: ieee802154 2017-09-20
Here comes a pull request for ieee802154 changes I have queued up for
this merge window.
Normally these have been coming through the bluetooth tree but as this
three have been falling through the cracks so far and I have to review
and ack all of them anyway I think it makes sense if I save the
bluetooth people some work and handle them directly.
Its the first pull request I send to you so please let me know if I did
something wrong or if you prefer a different format.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 23 Sep 2017 04:28:01 +0000 (21:28 -0700)]
Merge branch 'cxgb4-tc-flower'
Rahul Lakkireddy says:
====================
cxgb4: add support to offload tc flower
This series of patches add support to offload tc flower onto Chelsio
NICs.
Patch 1 adds basic skeleton to prepare for offloading tc flower flows.
Patch 2 adds support to add/remove flows for offload. Flows can have
accompanying masks. Following match and action are currently supported
for offload:
Match: ether-protocol, IPv4/IPv6 addresses, L4 ports (TCP/UDP)
Action: drop, redirect to another port on the device.
Patch 3 adds support to offload tc-flower flows having
vlan actions: pop, push, and modify.
Patch 4 adds support to fetch stats for the offloaded tc flower flows
from hardware.
Support for offloading more match and action types are to be followed
in subsequent series.
v2:
- Setting ftid to -1 not required after bitmap_find_free_region
in cxgb4_get_free_ftid.
- Direct return can be used as jumping to error path is not needed
if flower entry allocation failed in cxgb4_tc_flower_replace.
Same applies if flower entry not found in cxgb4_tc_flower_destroy.
- Also, removed an extra return from cxgb4_tc_flower_destroy.
- Avoid wrapping line for netdev_err message. Also, use
consistent error message string.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Thu, 21 Sep 2017 18:11:16 +0000 (23:41 +0530)]
cxgb4: fetch stats for offloaded tc flower flows
Add support to retrieve stats from hardware for offloaded tc flower
flows. Also, poll for the stats of offloaded flows via timer callback.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Thu, 21 Sep 2017 18:11:15 +0000 (23:41 +0530)]
cxgb4: add support to offload action vlan
Add support for offloading tc-flower flows having
vlan actions: pop, push and modify.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Thu, 21 Sep 2017 18:11:14 +0000 (23:41 +0530)]
cxgb4: add basic tc flower offload support
Add support to add/remove flows for offload. Following match
and action are supported for offloading a flow:
Match: ether-protocol, IPv4/IPv6 addresses, L4 ports (TCP/UDP)
Action: drop, redirect to another port on the device.
The qualifying flows can have accompanying mask information.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Thu, 21 Sep 2017 18:11:13 +0000 (23:41 +0530)]
cxgb4: add tc flower offload skeleton
Add basic skeleton to prepare for offloading tc-flower flows.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Thu, 21 Sep 2017 20:33:29 +0000 (23:33 +0300)]
net: use 32-bit arithmetic while allocating net device
Private part of allocation is never big enough to warrant size_t.
Space savings:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-10 (-10)
function old new delta
alloc_netdev_mqs 1120 1110 -10
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Fri, 22 Sep 2017 02:25:22 +0000 (10:25 +0800)]
net: Remove useless function skb_header_release
There is no one which would invokes the function skb_header_release.
So just remove it now.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Sep 2017 03:40:11 +0000 (17:40 -1000)]
Merge tag 'acpi-4.14-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix the initialization of resources in the ACPI WDAT watchdog
driver, a recent regression in the ACPI device properties handling, a
recent change in behavior causing the ACPI_HANDLE() macro to only work
for GPL code and create a MAINTAINERS entry for ACPI PMIC drivers in
order to specify the official reviewers for that code.
Specifics:
- Fix the initialization of resources in the ACPI WDAT watchdog
driver that uses unititialized memory which causes compiler
warnings to be triggered (Arnd Bergmann).
- Fix a recent regression in the ACPI device properties handling that
causes some device properties data to be skipped during enumeration
(Sakari Ailus).
- Fix a recent change in behavior that caused the ACPI_HANDLE() macro
to stop working for non-GPL code which is a problem for the NVidia
binary graphics driver, for example (John Hubbard).
- Add a MAINTAINERS entry for the ACPI PMIC drivers to specify the
official reviewers for that code (Rafael Wysocki)"
* tag 'acpi-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: properties: Return _DSD hierarchical extension (data) sub-nodes correctly
ACPI / bus: Make ACPI_HANDLE() work for non-GPL code again
ACPI / watchdog: properly initialize resources
ACPI / PMIC: Add code reviewers to MAINTAINERS
David S. Miller [Sat, 23 Sep 2017 03:33:18 +0000 (20:33 -0700)]
Merge branch 'net-fix-reuseaddr-regression'
Josef Bacik says:
====================
net: fix reuseaddr regression
I introduced a regression when reworking the fastreuse port stuff that allows
bind conflicts to occur once a reuseaddr successfully opens on an existing tb.
The root cause is I reversed an if statement which caused us to set the tb as if
there were no owners on the socket if there were, which obviously is not
correct.
Dave could you please queue these changes up for -stable, I've run them through
the net tests and added another test to check for this problem specifically.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Sat, 23 Sep 2017 00:20:08 +0000 (20:20 -0400)]
inet: fix improper empty comparison
When doing my reuseport rework I screwed up and changed a
if (hlist_empty(&tb->owners))
to
if (!hlist_empty(&tb->owners))
This is obviously bad as all of the reuseport/reuse logic was reversed,
which caused weird problems like allowing an ipv4 bind conflict if we
opened an ipv4 only socket on a port followed by an ipv6 only socket on
the same port.
Fixes:
b9470c27607b ("inet: kill smallest_size and smallest_port")
Reported-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Sat, 23 Sep 2017 00:20:07 +0000 (20:20 -0400)]
net: use inet6_rcv_saddr to compare sockets
In ipv6_rcv_saddr_equal() we need to use inet6_rcv_saddr(sk) for the
ipv6 compare with the fast socket information to make sure we're doing
the proper comparisons.
Fixes:
637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk")
Reported-and-tested-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Sat, 23 Sep 2017 00:20:06 +0000 (20:20 -0400)]
net: set tb->fast_sk_family
We need to set the tb->fast_sk_family properly so we can use the proper
comparison function for all subsequent reuseport bind requests.
Fixes:
637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk")
Reported-and-tested-by: Cole Robinson <crobinso@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 22 Sep 2017 23:42:37 +0000 (19:42 -0400)]
net: orphan frags on stand-alone ptype in dev_queue_xmit_nit
Zerocopy skbs frags are copied when the skb is looped to a local sock.
Commit
1080e512d44d ("net: orphan frags on receive") introduced calls
to skb_orphan_frags to deliver_skb and __netif_receive_skb for this.
With msg_zerocopy, these skbs can also exist in the tx path and thus
loop from dev_queue_xmit_nit. This already calls deliver_skb in its
loop. But it does not orphan before a separate pt_prev->func().
Add the missing skb_orphan_frags_rx.
Changes
v1->v2: handle skb_orphan_frags_rx failure
Fixes:
1f8b977ab32d ("sock: enable MSG_ZEROCOPY")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Sep 2017 03:28:59 +0000 (17:28 -1000)]
Merge tag 'pm-4.14-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a cpufreq regression introduced by recent changes related to
the generic DT driver, an initialization time memory leak in cpuidle
on ARM, a PM core bug that may cause system suspend/resume to fail on
some systems, a request type validation issue in the PM QoS framework
and two documentation-related issues.
Specifics:
- Fix a regression in cpufreq on systems using DT as the source of
CPU configuration information where two different code paths
attempt to create the cpufreq-dt device object (there can be only
one) and fix up the "compatible" matching for some TI platforms on
top of that (Viresh Kumar, Dave Gerlach).
- Fix an initialization time memory leak in cpuidle on ARM which
occurs if the cpuidle driver initialization fails (Stefan Wahren).
- Fix a PM core function that checks whether or not there are any
system suspend/resume callbacks for a device, but forgets to check
legacy callbacks which then may be skipped incorrectly and the
system may crash and/or the device may become unusable after a
suspend-resume cycle (Rafael Wysocki).
- Fix request type validation for latency tolerance PM QoS requests
which may lead to unexpected behavior (Jan Schönherr).
- Fix a broken link to PM documentation from a header file and a typo
in a PM document (Geert Uytterhoeven, Rafael Wysocki)"
* tag 'pm-4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: ti-cpufreq: Support additional am43xx platforms
ARM: cpuidle: Avoid memleak if init fail
cpufreq: dt-platdev: Add some missing platforms to the blacklist
PM: core: Fix device_pm_check_callbacks()
PM: docs: Drop an excess character from devices.rst
PM / QoS: Use the correct variable to check the QoS request type
driver core: Fix link to device power management documentation
Linus Torvalds [Sat, 23 Sep 2017 03:23:41 +0000 (17:23 -1000)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- fixes for two long standing issues (lock up and a crash) in force
feedback handling in uinput driver
- tweak to firmware update timing in Elan I2C touchpad driver.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - extend Flash-Write delay
Input: uinput - avoid crash when sending FF request to device going away
Input: uinput - avoid FF flush when destroying device
Linus Torvalds [Sat, 23 Sep 2017 02:16:41 +0000 (16:16 -1000)]
Merge tag 'seccomp-v4.14-rc2' of git://git./linux/kernel/git/kees/linux
Pull seccomp updates from Kees Cook:
"Major additions:
- sysctl and seccomp operation to discover available actions
(tyhicks)
- new per-filter configurable logging infrastructure and sysctl
(tyhicks)
- SECCOMP_RET_LOG to log allowed syscalls (tyhicks)
- SECCOMP_RET_KILL_PROCESS as the new strictest possible action
- self-tests for new behaviors"
[ This is the seccomp part of the security pull request during the merge
window that was nixed due to unrelated problems - Linus ]
* tag 'seccomp-v4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
samples: Unrename SECCOMP_RET_KILL
selftests/seccomp: Test thread vs process killing
seccomp: Implement SECCOMP_RET_KILL_PROCESS action
seccomp: Introduce SECCOMP_RET_KILL_PROCESS
seccomp: Rename SECCOMP_RET_KILL to SECCOMP_RET_KILL_THREAD
seccomp: Action to log before allowing
seccomp: Filter flag to log all actions except SECCOMP_RET_ALLOW
seccomp: Selftest for detection of filter flag support
seccomp: Sysctl to configure actions that are allowed to be logged
seccomp: Operation for checking if an action is available
seccomp: Sysctl to display available actions
seccomp: Provide matching filter for introspection
selftests/seccomp: Refactor RET_ERRNO tests
selftests/seccomp: Add simple seccomp overhead benchmark
selftests/seccomp: Add tests for basic ptrace actions
Linus Torvalds [Sat, 23 Sep 2017 02:11:48 +0000 (16:11 -1000)]
Merge tag '4.14-smb3-fixes-from-recent-test-events-for-stable' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Various SMB3 fixes for stable and security improvements from the
recently completed SMB3/Samba test events
* tag '4.14-smb3-fixes-from-recent-test-events-for-stable' of git://git.samba.org/sfrench/cifs-2.6:
SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags
SMB3: handle new statx fields
SMB: Validate negotiate (to protect against downgrade) even if signing off
cifs: release auth_key.response for reconnect.
cifs: release cifs root_cred after exit_cifs
CIFS: make arrays static const, reduces object code size
[SMB3] Update session and share information displayed for debugging SMB2/SMB3
cifs: show 'soft' in the mount options for hard mounts
SMB3: Warn user if trying to sign connection that authenticated as guest
SMB3: Fix endian warning
Fix SMB3.1.1 guest authentication to Samba
Linus Torvalds [Sat, 23 Sep 2017 02:09:31 +0000 (16:09 -1000)]
Merge tag 'ceph-for-4.14-rc2' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Two small but important fixes: RADOS semantic change in upcoming v12.2.1
release and a rare NULL dereference in create_session_open_msg()"
* tag 'ceph-for-4.14-rc2' of git://github.com/ceph/ceph-client:
ceph: avoid panic in create_session_open_msg() if utsname() returns NULL
libceph: don't allow bidirectional swap of pg-upmap-items
Stefan Schmidt [Fri, 22 Sep 2017 12:28:46 +0000 (14:28 +0200)]
MAINTAINERS: update git tree locations for ieee802154 subsystem
Patches for ieee802154 will go through my new trees towards netdev from
now on. The 6LoWPAN subsystem will stay as is (shared between ieee802154
and bluetooth) and go through the bluetooth tree as usual.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 22 Sep 2017 06:38:58 +0000 (14:38 +0800)]
virtio-net: correctly set xdp_xmit for mergeable buffer
We should set xdp_xmit only when xdp_do_redirect() succeed.
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steve French [Fri, 22 Sep 2017 06:40:27 +0000 (01:40 -0500)]
SMB3: Don't ignore O_SYNC/O_DSYNC and O_DIRECT flags
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Linus Torvalds [Fri, 22 Sep 2017 23:09:11 +0000 (13:09 -1000)]
Merge tag 'pci-v4.14-fixes-2' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix endpoint "end of test" interrupt issue (introduced in v4.14-rc1)
(John Keeping)
- fix MIPS use-after-free map_irq() issue (introduced in v4.14-rc1)
(Lorenzo Pieralisi)
* tag 'pci-v4.14-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: endpoint: Use correct "end of test" interrupt
MIPS: PCI: Move map_irq() hooks out of initdata
Linus Torvalds [Fri, 22 Sep 2017 23:06:05 +0000 (13:06 -1000)]
Merge tag 'iommu-fixes-v4.14-rc1' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- two Kconfig fixes to fix dependencies that cause compile failures
when they are not fulfilled.
- a section mismatch fix for Intel VT-d
- a fix for PCI topology detection in ARM device-tree code
* tag 'iommu-fixes-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/of: Remove PCI host bridge node check
iommu/qcom: Depend on HAS_DMA to fix compile error
iommu/vt-d: Fix harmless section mismatch warning
iommu: Add missing dependencies
Linus Torvalds [Fri, 22 Sep 2017 23:02:54 +0000 (13:02 -1000)]
Merge git://git./linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile fixes from Chris Metcalf:
"These are a code cleanup and config cleanup, respectively"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: array underflow in setup_maxnodemem()
tile: defconfig: Cleanup from old Kconfig options
Linus Torvalds [Fri, 22 Sep 2017 23:01:16 +0000 (13:01 -1000)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- #ifdef CONFIG_EFI around __efi_fpsimd_begin/end
- Assembly code alignment reduced to 4 bytes from 16
- Ensure the kernel is compiled for LP64 (there are some arm64
compilers around defaulting to ILP32)
- Fix arm_pmu_acpi memory leak on the error path
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
drivers/perf: arm_pmu_acpi: Release memory obtained by kasprintf
arm64: ensure the kernel is compiled for LP64
arm64: relax assembly code alignment from 16 byte to 4 byte
arm64: efi: Don't include EFI fpsimd save/restore code in non-EFI kernels
Steve French [Fri, 22 Sep 2017 02:32:29 +0000 (21:32 -0500)]
SMB3: handle new statx fields
We weren't returning the creation time or the two easily supported
attributes (ENCRYPTED or COMPRESSED) for the getattr call to
allow statx to return these fields.
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>\
Acked-by: Jeff Layton <jlayton@poochiereds.net>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Tobias Klauser [Fri, 22 Sep 2017 07:42:42 +0000 (09:42 +0200)]
arch: remove unused *_segments() macros/functions
Some architectures define the no-op macros/functions copy_segments,
release_segments and forget_segments. These are used nowhere in the
tree, so removed them.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [for arch/arc]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafael J. Wysocki [Fri, 22 Sep 2017 21:38:45 +0000 (23:38 +0200)]
Merge branches 'acpi-pmic', 'acpi-bus', 'acpi-wdat' and 'acpi-properties'
* acpi-pmic:
ACPI / PMIC: Add code reviewers to MAINTAINERS
* acpi-bus:
ACPI / bus: Make ACPI_HANDLE() work for non-GPL code again
* acpi-wdat:
ACPI / watchdog: properly initialize resources
* acpi-properties:
ACPI: properties: Return _DSD hierarchical extension (data) sub-nodes correctly
Rafael J. Wysocki [Fri, 22 Sep 2017 20:45:54 +0000 (22:45 +0200)]
Merge branches 'pm-cpufreq' and 'pm-cpuidle'
* pm-cpufreq:
cpufreq: ti-cpufreq: Support additional am43xx platforms
cpufreq: dt-platdev: Add some missing platforms to the blacklist
* pm-cpuidle:
ARM: cpuidle: Avoid memleak if init fail
Rafael J. Wysocki [Fri, 22 Sep 2017 20:45:28 +0000 (22:45 +0200)]
Merge branches 'pm-core', 'pm-qos' and 'pm-docs'
* pm-core:
PM: core: Fix device_pm_check_callbacks()
* pm-qos:
PM / QoS: Use the correct variable to check the QoS request type
* pm-docs:
PM: docs: Drop an excess character from devices.rst
driver core: Fix link to device power management documentation
Helge Deller [Fri, 22 Sep 2017 19:57:11 +0000 (21:57 +0200)]
parisc: Unbreak bootloader due to gcc-7 optimizations
gcc-7 optimizes the byte-wise accesses of get_unaligned_le32() into
word-wise accesses if the 32-bit integer output_len is declared as
external. This panics then the bootloader since we don't have the
unaligned access fault trap handler installed during boot time.
Avoid this optimization by declaring output_len as byte-aligned and thus
unbreak the bootloader code.
Additionally, compile the boot code optimized for size.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 22 Sep 2017 20:24:02 +0000 (22:24 +0200)]
parisc: Reintroduce option to gzip-compress the kernel
By adding the feature to build the kernel as self-extracting
executeable, the possibility to simply compress the kernel with gzip was
lost.
This patch now reintroduces this possibilty again and leaves it up to
the user to decide how the kernel should be built.
The palo bootloader is able to natively load both formats.
Signed-off-by: Helge Deller <deller@gmx.de>
John Johansen [Thu, 31 Aug 2017 16:54:43 +0000 (09:54 -0700)]
apparmor: fix apparmorfs DAC access permissions
The DAC access permissions for several apparmorfs files are wrong.
.access - needs to be writable by all tasks to perform queries
the others in the set only provide a read fn so should be read only.
With policy namespace virtualization all apparmor needs to control
the permission and visibility checks directly which means DAC
access has to be allowed for all user, group, and other.
BugLink: http://bugs.launchpad.net/bugs/1713103
Fixes:
c97204baf840b ("apparmor: rename apparmor file fns and data to indicate use")
Signed-off-by: John Johansen <john.johansen@canonical.com>
John Johansen [Wed, 23 Aug 2017 19:10:39 +0000 (12:10 -0700)]
apparmor: fix build failure on sparc caused by undeclared signals
In file included from security/apparmor/ipc.c:23:0:
security/apparmor/include/sig_names.h:26:3: error: 'SIGSTKFLT' undeclared here (not in a function)
[SIGSTKFLT] = 16, /* -, 16, - */
^
security/apparmor/include/sig_names.h:26:3: error: array index in initializer not of integer type
security/apparmor/include/sig_names.h:26:3: note: (near initialization for 'sig_map')
security/apparmor/include/sig_names.h:51:3: error: 'SIGUNUSED' undeclared here (not in a function)
[SIGUNUSED] = 34, /* -, 31, - */
^
security/apparmor/include/sig_names.h:51:3: error: array index in initializer not of integer type
security/apparmor/include/sig_names.h:51:3: note: (near initialization for 'sig_map')
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes:
c6bf1adaecaa ("apparmor: add the ability to mediate signals")
Signed-off-by: John Johansen <john.johansen@canonical.com>
John Johansen [Wed, 16 Aug 2017 16:33:48 +0000 (09:33 -0700)]
apparmor: fix incorrect type assignment when freeing proxies
sparse reports
poisoning the proxy->label before freeing the struct is resulting in
a sparse build warning.
../security/apparmor/label.c:52:30: warning: incorrect type in assignment (different address spaces)
../security/apparmor/label.c:52:30: expected struct aa_label [noderef] <asn:4>*label
../security/apparmor/label.c:52:30: got struct aa_label *<noident>
fix with RCU_INIT_POINTER as this is one of those cases where
rcu_assign_pointer() is not needed.
Signed-off-by: John Johansen <john.johansen@canonical.com>
John Johansen [Wed, 16 Aug 2017 12:48:06 +0000 (05:48 -0700)]
apparmor: ensure unconfined profiles have dfas initialized
Generally unconfined has early bailout tests and does not need the
dfas initialized, however if an early bailout test is ever missed
it will result in an oops.
Be defensive and initialize the unconfined profile to have null dfas
(no permission) so if an early bailout test is missed we fail
closed (no perms granted) instead of oopsing.
Signed-off-by: John Johansen <john.johansen@canonical.com>
John Johansen [Wed, 16 Aug 2017 12:40:49 +0000 (05:40 -0700)]
apparmor: fix race condition in null profile creation
There is a race when null- profile is being created between the
initial lookup/creation of the profile and lock/addition of the
profile. This could result in multiple version of a profile being
added to the list which need to be removed/replaced.
Since these are learning profile their is no affect on mediation.
Signed-off-by: John Johansen <john.johansen@canonical.com>
John Johansen [Wed, 16 Aug 2017 15:59:57 +0000 (08:59 -0700)]
apparmor: move new_null_profile to after profile lookup fns()
new_null_profile will need to use some of the profile lookup fns()
so move instead of doing forward fn declarations.
Signed-off-by: John Johansen <john.johansen@canonical.com>
John Johansen [Wed, 19 Jul 2017 06:18:33 +0000 (23:18 -0700)]
apparmor: add base infastructure for socket mediation
Provide a basic mediation of sockets. This is not a full net mediation
but just whether a spcific family of socket can be used by an
application, along with setting up some basic infrastructure for
network mediation to follow.
the user space rule hav the basic form of
NETWORK RULE = [ QUALIFIERS ] 'network' [ DOMAIN ]
[ TYPE | PROTOCOL ]
DOMAIN = ( 'inet' | 'ax25' | 'ipx' | 'appletalk' | 'netrom' |
'bridge' | 'atmpvc' | 'x25' | 'inet6' | 'rose' |
'netbeui' | 'security' | 'key' | 'packet' | 'ash' |
'econet' | 'atmsvc' | 'sna' | 'irda' | 'pppox' |
'wanpipe' | 'bluetooth' | 'netlink' | 'unix' | 'rds' |
'llc' | 'can' | 'tipc' | 'iucv' | 'rxrpc' | 'isdn' |
'phonet' | 'ieee802154' | 'caif' | 'alg' | 'nfc' |
'vsock' | 'mpls' | 'ib' | 'kcm' ) ','
TYPE = ( 'stream' | 'dgram' | 'seqpacket' | 'rdm' | 'raw' |
'packet' )
PROTOCOL = ( 'tcp' | 'udp' | 'icmp' )
eg.
network,
network inet,
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Seth Arnold <seth.arnold@canonical.com>
John Johansen [Wed, 19 Jul 2017 06:41:13 +0000 (23:41 -0700)]
apparmor: add more debug asserts to apparmorfs
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Seth Arnold <seth.arnold@canonical.com>
John Johansen [Wed, 19 Jul 2017 06:37:18 +0000 (23:37 -0700)]
apparmor: make policy_unpack able to audit different info messages
Switch unpack auditing to using the generic name field in the audit
struct and make it so we can start adding new info messages about
why an unpack failed.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Seth Arnold <seth.arnold@canonical.com>