OSDN Git Service
Suresh Siddha [Thu, 19 Apr 2012 02:27:39 +0000 (19:27 -0700)]
tick: Fix the spurious broadcast timer ticks after resume
During resume, tick_resume_broadcast() programs the broadcast timer in
oneshot mode unconditionally. On the platforms where broadcast timer
is not really required, this will generate spurious broadcast timer
ticks upon resume. For example, on the always running apic timer
platforms with HPET, I see spurious hpet tick once every ~5minutes
(which is the 32-bit hpet counter wraparound time).
Similar to boot time, during resume make the oneshot mode setting of
the broadcast clock event device conditional on the state of active
broadcast users.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: svenjoac@gmx.de
Cc: torvalds@linux-foundation.org
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/1334802459.28674.209.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Wed, 18 Apr 2012 15:31:58 +0000 (17:31 +0200)]
tick: Ensure that the broadcast device is initialized
Santosh found another trap when we avoid to initialize the broadcast
device in the switch_to_oneshot code. The broadcast device might be
still in SHUTDOWN state when we actually need to use it. That
obviously breaks, as set_next_event() is called on a shutdown
device. This did not break on x86, but Suresh analyzed it:
From the review, most likely on Sven's system we are force enabling
the hpet using the pci quirk's method very late. And in this case,
hpet_clockevent (which will be global_clock_event) handler can be
null, specifically as this platform might not be using deeper c-states
and using the reliable APIC timer.
Prior to commit '
fa4da365bc7772c', that handler will be set to
'tick_handle_oneshot_broadcast' when we switch the broadcast timer to
oneshot mode, even though we don't use it. Post commit
'
fa4da365bc7772c', we stopped switching the broadcast mode to oneshot
as this is not really needed and his platform's global_clock_event's
handler will remain null. While on my SNB laptop, same is set to
'clockevents_handle_noop' because hpet gets enabled very early. (noop
handler on my platform set when the early enabled hpet timer gets
replaced by the lapic timer).
But the commit '
fa4da365bc7772c' tracked the broadcast timer mode in
the SW as oneshot, even though it didn't touch the HW timer. During
resume however, tick_resume_broadcast() saw the SW broadcast mode as
oneshot and actually programmed the broadcast device also into oneshot
mode. So this triggered the null pointer de-reference after the hpet
wraps around and depending on what the hpet counter is set to. On the
normal platforms where hpet gets enabled early we should be seeing a
spurious interrupt (in my SNB laptop I see one spurious interrupt
after around 5 minutes ;) which is 32-bit hpet counter wraparound
time), but that's a separate issue.
Enforce the mode setting when trying to set an event.
Reported-and-tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: torvalds@linux-foundation.org
Cc: svenjoac@gmx.de
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181723350.2542@ionos
Thomas Gleixner [Wed, 18 Apr 2012 10:08:23 +0000 (12:08 +0200)]
tick: Fix oneshot broadcast setup really
Sven Joachim reported, that suspend/resume on rc3 trips over a NULL
pointer dereference. Linus spotted the clockevent handler being NULL.
commit
fa4da365b(clockevents: tTack broadcast device mode change in
tick_broadcast_switch_to_oneshot()) tried to fix a problem with the
broadcast device setup, which was introduced in commit
77b0d60c5(
clockevents: Leave the broadcast device in shutdown mode when not
needed).
The initial commit avoided to set up the broadcast device when no
broadcast request bits were set, but that left the broadcast device
disfunctional. In consequence deep idle states which need the
broadcast device were not woken up.
commit
fa4da365b tried to fix that by initializing the state of the
broadcast facility, but that missed the fact, that nothing initializes
the event handler and some other state of the underlying clock event
device.
The fix is to revert both commits and make only the mode setting of
the clock event device conditional on the state of active broadcast
users.
That initializes everything except the low level device mode, but this
happens when the broadcast functionality is invoked by deep idle.
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181205540.2542@ionos
Linus Torvalds [Tue, 17 Apr 2012 20:30:34 +0000 (13:30 -0700)]
Merge tag 'ext4_for_linus' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 regression fixes from Ted Ts'o:
"This fixes a scalability problem reported by Andi Kleen and Tim Chen;
they were quite secretive about the precise nature of their workload,
but they later admitted that it only showed up when they were using a
large sparse file, so the amount of data I/O that was needed was close
to zero.
I'm not sure how realistic this is and it's only a regression if you
consider changes made since 2.6.39 to be a "regression" vis-a-vis the
policy regarding post-merge window bug fixes, but Linus agreed it was
worth fixing, so I'm including it in this pull request.
This also fixes the journalled quota mount options, which I
accidentally broke while I was cleaning up the mount option handling."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix handling of journalled quota options
ext4: address scalability issue by removing extent cache statistics
Linus Torvalds [Tue, 17 Apr 2012 20:21:50 +0000 (13:21 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A bunch of endianness fixes and a couple of nfsd error value fixes.
Speaking of endianness stuff, I'm rather tempted to slap
ccflags-y += -D__CHECK_ENDIAN__
in fs/Makefile, if not making it default for the entire tree; nfsd
regressions I've caught make one hell of a pile and we'd obviously
benefit from having that kind of stuff caught earlier..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
lockd: fix the endianness bug
ocfs2: ->e_leaf_clusters endianness breakage
ocfs2: ->rl_count endianness breakage
ocfs: ->rl_used breakage on big-endian
ocfs2: ->l_next_free_req breakage on big-endian
btrfs: btrfs_root_readonly() broken on big-endian
ext4: fix endianness breakage in ext4_split_extent_at()
nfsd: fix compose_entry_fh() failure exits
nfsd: fix error value on allocation failure in nfsd4_decode_test_stateid()
nfsd: fix endianness breakage in TEST_STATEID handling
nfsd: fix error values returned by nfsd4_lockt() when nfsd_open() fails
nfsd: fix b0rken error value for setattr on read-only mount
Linus Torvalds [Tue, 17 Apr 2012 16:19:29 +0000 (09:19 -0700)]
Merge git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French.
* git://git.samba.org/sfrench/cifs-2.6:
Fix number parsing in cifs_parse_mount_options
Cleanup handling of NULL value passed for a mount option
Linus Torvalds [Tue, 17 Apr 2012 01:35:21 +0000 (18:35 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Handle failures of parsing immediate operands in the instruction decoder
perf archive: Correct cutting of symbolic link
perf tools: Ignore auto-generated bison/flex files
perf tools: Fix parsers' rules to dependencies
perf tools: fix NO_GTK2 Makefile config error
perf session: Skip event correctly for unknown id/machine
Linus Torvalds [Tue, 17 Apr 2012 01:34:12 +0000 (18:34 -0700)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio fixes from Michael S. Tsirkin:
"Here are some virtio fixes for 3.4: a test build fix, a patch by Ren
fixing naming for systems with a massive number of virtio blk devices,
and balloon fixes for powerpc by David Gibson.
There was some discussion about Ren's patch for virtio disc naming:
some people wanted to move the legacy name mangling function to the
block core. But there's no concensus on that yet, and we can always
deduplicate later. Added comments in the hope that this will stop
people from copying this legacy naming scheme into future drivers."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: fix handling of PAGE_SIZE != 4k
virtio_balloon: Fix endian bug
virtio_blk: helper function to format disk names
tools/virtio: fix up vhost/test module build
Rafael J. Wysocki [Mon, 16 Apr 2012 21:07:50 +0000 (23:07 +0200)]
PCI: Retry BARs restoration for Type 0 headers only
Some shortcomings introduced into pci_restore_state() by commit
26f41062f28d ("PCI: check for pci bar restore completion and retry")
have been fixed by recent commit
ebfc5b802fa76 ("PCI: Fix regression in
pci_restore_state(), v3"), but that commit treats all PCI devices as
those with Type 0 configuration headers.
That is not entirely correct, because Type 1 and Type 2 headers have
different layouts. In particular, the area occupied by BARs in Type 0
config headers contains the secondary status register in Type 1 ones and
it doesn't make sense to retry the restoration of that register even if
the value read back from it after a write is not the same as the written
one (it very well may be different).
For this reason, make pci_restore_state() only retry the restoration
of BARs for Type 0 config headers. This effectively makes it behave
as before commit
26f41062f28d for all header types except for Type 0.
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Tue, 17 Apr 2012 02:21:39 +0000 (19:21 -0700)]
Documentation: maintainer change
I'm dropping off as Documentation/ maintainer.
Rob Landley has agreed to take it over. Thanks, Rob.
I'll still be around reviewing patches and testing.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Luck, Tony [Mon, 16 Apr 2012 23:28:01 +0000 (16:28 -0700)]
ia64: fix futex_atomic_cmpxchg_inatomic()
Michel Lespinasse cleaned up the futex calling conventions in commit
37a9d912b24f ("futex: Sanitize cmpxchg_futex_value_locked API").
But the ia64 implementation was subtly broken. Gcc does not know that
register "r8" will be updated by the fault handler if the cmpxchg
instruction takes an exception. So it feels safe in letting the
initialization of r8 slide to after the cmpxchg. Result: we always
return 0 whether the user address faulted or not.
Fix by moving the initialization of r8 into the __asm__ code so gcc
won't move it.
Reported-by: <emeric.maschino@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42757
Tested-by: <emeric.maschino@gmail.com>
Acked-by: Michel Lespinasse <walken@google.com>
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Theodore Ts'o [Mon, 16 Apr 2012 22:55:26 +0000 (18:55 -0400)]
ext4: fix handling of journalled quota options
Commit
26092bf5 broke handling of journalled quota mount options by
trying to parse argument of every mount option as a number. Fix this
by dealing with the quota options before we call match_int().
Thanks to Jan Kara for discovering this regression.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Joe Perches [Mon, 16 Apr 2012 19:35:11 +0000 (13:35 -0600)]
checkpatch: revert --strict test for net/ and drivers/net block comment style
Revert the --strict test for the old preferred block
comment style in drivers/net and net/
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Theodore Ts'o [Mon, 16 Apr 2012 16:16:20 +0000 (12:16 -0400)]
ext4: address scalability issue by removing extent cache statistics
Andi Kleen and Tim Chen have reported that under certain circumstances
the extent cache statistics are causing scalability problems due to
cache line bounces.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
Masami Hiramatsu [Fri, 13 Apr 2012 03:24:27 +0000 (12:24 +0900)]
x86: Handle failures of parsing immediate operands in the instruction decoder
This can happen if the instruction is much longer than the maximum length,
or if insn->opnd_bytes is manually changed.
This patch also fixes warnings from -Wswitch-default flag.
Reported-by: Prashanth Nageshappa <prashanth@linux.vnet.ibm.com>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Anton Arapov <anton@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120413032427.32577.42602.stgit@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Mon, 16 Apr 2012 01:28:29 +0000 (18:28 -0700)]
Linux 3.4-rc3
Linus Torvalds [Mon, 16 Apr 2012 00:35:19 +0000 (17:35 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
Linus Torvalds [Mon, 16 Apr 2012 00:23:00 +0000 (17:23 -0700)]
x86-32: fix up strncpy_from_user() sign error
The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.
We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.
Bug introduced in commit
92ae03f2ef99 ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up"). On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.
I had actually tested the corner-cases, I had only tested them on
x86-64. Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)
This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way. 'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rabin Vincent [Sat, 14 Apr 2012 20:51:32 +0000 (21:51 +0100)]
ARM: 7386/1: jump_label: fixup for rename to static_key
c5905afb0 ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key. Fixup ARM for this to
eliminate these build warnings:
include/linux/jump_label.h:113:2:
warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
include/asm/jump_label.h:17:82:
note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jonathan Austin [Thu, 12 Apr 2012 16:45:25 +0000 (17:45 +0100)]
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.
This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.
Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Thu, 12 Apr 2012 16:15:08 +0000 (17:15 +0100)]
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.
This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Tue, 10 Apr 2012 11:37:42 +0000 (12:37 +0100)]
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.
Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rafael J. Wysocki [Sun, 15 Apr 2012 19:40:40 +0000 (21:40 +0200)]
PCI: Fix regression in pci_restore_state(), v3
Commit
26f41062f28d ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.
First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one). Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt. Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.
All of this actually caused resume failures for some devices on Mikko's
system.
To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value. Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 15 Apr 2012 18:14:54 +0000 (11:14 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
- A handful of warning and build fixes for Qualcomm MSM
- Build/warning and bug fixes for Samsung Exynos
- A fix from Rob Herring that removes misplaced interrupt-parent
properties from a few device trees
- A fix to OMAP dealing with cpufreq build errors, removing some of the
offending code since it was redundant anyway
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
ARM: dts: remove blank interrupt-parent properties
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
Linus Torvalds [Sun, 15 Apr 2012 18:14:07 +0000 (11:14 -0700)]
Merge tag 'sound-3.4' of git://git./linux/kernel/git/tiwai/sound
Pull another round of sound fixes from Takashi Iwai:
"A few regression fixes for Realtek HD-audio codecs, mainly specific to
some laptop models."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
ALSA: hda/realtek - Add a few ALC882 model strings back
Martin K. Petersen [Sun, 15 Apr 2012 03:01:28 +0000 (23:01 -0400)]
SCSI: Fix error handling when no ULD is attached
Commit
18a4d0a22ed6 ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael S. Tsirkin [Thu, 12 Apr 2012 13:38:00 +0000 (16:38 +0300)]
virtio_balloon: fix handling of PAGE_SIZE != 4k
As reported by David Gibson, current code handles PAGE_SIZE != 4k
completely wrong which can lead to guest memory corruption errors:
- page_to_balloon_pfn is wrong: e.g. on system with 64K page size
it gives the same pfn value for 16 different pages.
- we also need to convert back to linux pfns when we free.
- for each linux page we need to tell host about multiple balloon
pages, but code only adds one pfn to the array.
This patch fixes all that, tested with a 64k ppc64 kernel.
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
David Gibson [Thu, 12 Apr 2012 05:36:34 +0000 (15:36 +1000)]
virtio_balloon: Fix endian bug
Although virtio config space fields are usually in guest-native endian,
the spec for the virtio balloon device explicitly states that both fields
in its config space are little-endian.
However, the current virtio_balloon driver does not have a suitable endian
swap for the 'num_pages' field, although it does have one for the 'actual'
field. This patch corrects the bug, adding sparse annotation while we're
at it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Ingo Molnar [Sun, 15 Apr 2012 06:02:36 +0000 (08:02 +0200)]
Merge tag 'perf-urgent-for-mingo' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf tooling fixes from Arnaldo Carvalho de Melo:
. Properly handle ~/.debug, the build id cache, when it is a symlink,
fix from Chanho Park
. Fixes for the parser generation process, from Jiri Olsa and Namhyung Kim
. Fix build when NO_GTK2 is specified, From Stephane Eranian
. When a machine is not found, bump the relevant error stat but return
0, so that we correctly move to the next perf event. Fix from Jiri Olsa
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Olof Johansson [Sun, 15 Apr 2012 00:50:45 +0000 (17:50 -0700)]
Merge branch 'v3.4-samsung-fixes-2' of git://git./linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.4-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
Kevin Hilman [Fri, 13 Apr 2012 20:52:15 +0000 (13:52 -0700)]
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
Now that we have OPP layer, and OMAP CPUfreq driver is using it, we no
longer need/use the clock framework code for filling up CPUfreq
tables. Remove it.
Removing this code also eliminates build errors when CPU_FREQ_TABLE
support is not enabled.
Thanks to Russell King for pointing out the parts I missed under
plat-omap in the original version and also pointing out the build
errors when CPUFREQ_TABLE support was not enabled.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rob Herring [Thu, 12 Apr 2012 15:17:28 +0000 (10:17 -0500)]
ARM: dts: remove blank interrupt-parent properties
These were incorrectly introduced and can cause problems for of_irq_init.
The correct way to define a root controller is no interrupt-parent set at
all or the interrupt-parent is set to the root controller itself when
inherited from a parent node.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 15 Apr 2012 00:44:21 +0000 (17:44 -0700)]
Merge branch 'msm-fix' of git://git./linux/kernel/git/davidb/linux-msm into fixes
From David Brown:
"Here are some fixes for msm that fix problems caused by the latest
ARM code. The ones from Daniel remove unneeded fixups that now
cause compilation failures. Mine fix section mismatches, that were
incompletely fixed earlier."
* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
Chanho Park [Mon, 2 Apr 2012 06:28:29 +0000 (15:28 +0900)]
perf archive: Correct cutting of symbolic link
If a '$PERF_BUILDID_DIR'(typically $HOME/.debug) is a symbolic link
directory, cutting of the path will fail.
Here is an example where a buildid directory is a symbolic link.
/ # ls -al /root
lrwxrwxrwx 1 root root 13 Mar 26 2012 /root -> opt/home/root
/ # cd ~
/opt/home/root # perf record -a -g sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.322 MB perf.data (~14057 samples) ]
/opt/home/root # perf archive
tar: Removing leading `/' from member names
Now please run:
$ tar xvf perf.data.tar.bz2 -C ~/.debug
wherever you need to run 'perf report' on.
/opt/home/root # mkdir temp
/opt/home/root # tar xf perf.data.tar.bz2 -C ./temp
/opt/home/root # find ./temp -name "*kernel*"
./temp/opt/home/root/.debug/[kernel.kallsyms]
-> If successfully cut off the path, [kernel.kallsyms] is located
in top of the archived file.
This patch enables to cut correctly even if the buildid directory
is a symbolic link.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333348109-12598-1-git-send-email-chanho61.park@samsung.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Namhyung Kim [Mon, 9 Apr 2012 05:11:14 +0000 (14:11 +0900)]
perf tools: Ignore auto-generated bison/flex files
The commit
65f3e56e0c81 ("perf tools: Remove auto-generated bison/flex
files") removed those files from git, so they'll be listed on untracked
files after building perf. Fix it.
Signed-off-by: Namhyung Kim <namhyung.kim@lge.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1333948274-20043-1-git-send-email-namhyung.kim@lge.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jiri Olsa [Wed, 11 Apr 2012 10:39:51 +0000 (12:39 +0200)]
perf tools: Fix parsers' rules to dependencies
Currently the parsers objects (bison/flex related) are each time perf
is built. No matter the generated files are already in place, the
parser generation is executed every time.
Changing the rules to have proper flex/bison objects generation
dependencies.
The parsers code is not rebuilt until the flex/bison source files
are touched. Also when flex/bison source is changed, only dependent
objects are rebuilt.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1334140791-3024-1-git-send-email-jolsa@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Sachin Kamat [Sat, 14 Apr 2012 14:53:51 +0000 (07:53 -0700)]
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
Add config dependency for Exynos4 and Exynos5 device tree enabled machine
files on config options ARCH_EXYNOS4 and ARCH_EXYNOS5 respectively.
Enabling machine support without proper ARCH support enabled is incorrect.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Linus Torvalds [Sat, 14 Apr 2012 14:48:13 +0000 (07:48 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf tool fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Finding struct machine fails for PERF_RECORD_MMAP
perf annotate: Validate addr in symbol__inc_addr_samples
perf hists browser: Fix NULL deref in hists browsing code
perf hists: Catch and handle out-of-date hist entry maps.
perf annotate: Fix hist decay
perf top: Add intel_idle to the skip list
Lubos Lunak [Wed, 21 Mar 2012 13:08:24 +0000 (14:08 +0100)]
do not export kernel's NULL #define to userspace
GCC's NULL is actually __null, which allows detecting some questionable
NULL usage and warn about it. Moreover each platform/compiler should
have its own stddef.h anyway (which is different from linux/stddef.h).
So there's no good reason to leak kernel's NULL to userspace and
override what the compiler provides.
Signed-off-by: Luboš Luňák <l.lunak@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marek Szyprowski [Tue, 10 Apr 2012 04:10:32 +0000 (21:10 -0700)]
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
The atmel_mxt_ts driver has been extended to support more 'configuration
objects' in commit
81c88a711 ("Input: atmel_mxt_ts - update object list"),
what broke the configuration values for NURI board. These values are
optional anyway, so remove them to get the driver working correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Tue, 10 Apr 2012 04:10:32 +0000 (21:10 -0700)]
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
On some versions of NURI and UniversalC210 boards, camera clocks are
routed directly to xusbxti clock source. This patch sets the correct
value for this clock to let usb and camera sensors to work correctly and
avoid division by zero on driver's probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Marek Szyprowski [Tue, 10 Apr 2012 04:10:32 +0000 (21:10 -0700)]
ARM: EXYNOS: fix regulator name for NURI board
Regulator names should not contain slash to avoid issues with debugfs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Maurus Cuelenaere [Sat, 14 Apr 2012 14:42:04 +0000 (07:42 -0700)]
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
When selecting SAMSUNG_PM_DEBUG, it complains about a missing printascii()
function if you do not select DEBUG_LL, so make the former select the latter.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Linus Torvalds [Sat, 14 Apr 2012 02:44:36 +0000 (19:44 -0700)]
Merge branch 'systemh-fixes' of git://git./linux/kernel/git/paulg/linux
Pull system.h fixups for less common arch's from Paul Gortmaker:
"Here is what is hopefully the last of the system.h related fixups.
The fixes for Alpha and ia64 are code relocations consistent with what
was done for the more mainstream architectures. Note that the
diffstat lines removed vs lines added are not the same since I've
fixed some of the whitespace issues in the relocated code blocks.
However they are functionally the same. Compile tested locally, plus
these two have been in linux-next for a while.
There is also a trivial one line system.h related fix for the Tilera
arch from Chris Metcalf to fix an implict include.."
* 'systemh-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
irq_work: fix compile failure on tile from missing include
ia64: populate the cmpxchg header with appropriate code
alpha: fix build failures from system.h dismemberment
Linus Torvalds [Sat, 14 Apr 2012 02:42:56 +0000 (19:42 -0700)]
Merge tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- a compile fix for au1*fb
- a fix to make kyrofb usable on x86_64
- a fix for uvesafb to prevent an oops due to NX-protection
"The fix for kyrofb is a bit large but it's just replacing "unsigned
long" by "u32" for 64 bit compatibility."
* tag 'fbdev-fixes-for-3.4-1' of git://github.com/schandinat/linux-2.6:
video:uvesafb: Fix oops that uvesafb try to execute NX-protected page
fbdev: fix au1*fb builds
kyrofb: fix on x86_64
Linus Torvalds [Sat, 14 Apr 2012 02:41:27 +0000 (19:41 -0700)]
Merge branch 'for-linus-min' of git://git./linux/kernel/git/mason/linux-btrfs
Pull the minimal btrfs branch from Chris Mason:
"We have a use-after-free in there, along with errors when mount -o
discard is enabled, and a BUG_ON(we should compile with UP more
often)."
* 'for-linus-min' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use commit root when loading free space cache
Btrfs: fix use-after-free in __btrfs_end_transaction
Btrfs: check return value of bio_alloc() properly
Btrfs: remove lock assert from get_restripe_target()
Btrfs: fix eof while discarding extents
Btrfs: fix uninit variable in repair_eb_io_failure
Revert "Btrfs: increase the global block reserve estimates"
Linus Torvalds [Sat, 14 Apr 2012 01:45:13 +0000 (18:45 -0700)]
Merge branch 'for-3.4/drivers' of git://git.kernel.dk/linux-block
Pull block driver bits from Jens Axboe:
- A series of fixes for mtip32xx. Most from Asai at Micron, but also
one from Greg, getting rid of the dependency on PCIE_HOTPLUG.
- A few bug fixes for xen-blkfront, and blkback.
- A virtio-blk fix for Vivek, making resize actually work.
- Two fixes from Stephen, making larger transfers possible on cciss.
This is needed for tape drive support.
* 'for-3.4/drivers' of git://git.kernel.dk/linux-block:
block: mtip32xx: remove HOTPLUG_PCI_PCIE dependancy
mtip32xx: dump tagmap on failure
mtip32xx: fix handling of commands in various scenarios
mtip32xx: Shorten macro names
mtip32xx: misc changes
mtip32xx: Add new sysfs entry 'status'
mtip32xx: make setting comp_time as common
mtip32xx: Add new bitwise flag 'dd_flag'
mtip32xx: fix error handling in mtip_init()
virtio-blk: Call revalidate_disk() upon online disk resize
xen/blkback: Make optional features be really optional.
xen/blkback: Squash the discard support for 'file' and 'phy' type.
mtip32xx: fix incorrect value set for drv_cleanup_done, and re-initialize and start port in mtip_restart_port()
cciss: Fix scsi tape io with more than 255 scatter gather elements
cciss: Initialize scsi host max_sectors for tape drive support
xen-blkfront: make blkif_io_lock spinlock per-device
xen/blkfront: don't put bdev right after getting it
xen-blkfront: use bitmap_set() and bitmap_clear()
xen/blkback: Enable blkback on HVM guests
xen/blkback: use grant-table.c hypercall wrappers
Linus Torvalds [Sat, 14 Apr 2012 01:07:19 +0000 (18:07 -0700)]
Merge branch 'for-3.4/core' of git://git.kernel.dk/linux-block
Pull block core bits from Jens Axboe:
"It's a nice and quiet round this time, since most of the tricky stuff
has been pushed to 3.5 to give it more time to mature. After a few
hectic block IO core changes for 3.3 and 3.2, I'm quite happy with a
slow round.
Really minor stuff in here, the only real functional change is making
the auto-unplug threshold a per-queue entity. The threshold is set so
that it's low enough that we don't hold off IO for too long, but still
big enough to get a nice benefit from the batched insert (and hence
queue lock cost reduction). For raid configurations, this currently
breaks down."
* 'for-3.4/core' of git://git.kernel.dk/linux-block:
block: make auto block plug flush threshold per-disk based
Documentation: Add sysfs ABI change for cfq's target latency.
block: Make cfq_target_latency tunable through sysfs.
block: use lockdep_assert_held for queue locking
block: blk_alloc_queue_node(): use caller's GFP flags instead of GFP_KERNEL
Kevin Hilman [Fri, 13 Apr 2012 20:32:30 +0000 (13:32 -0700)]
cpufreq: OMAP: fix build errors: depends on ARCH_OMAP2PLUS
The OMAP driver needs a 'depends on ARCH_OMAP2PLUS' since it only
builds for OMAP2+ platforms.
This 'depends on' was in the original patch from Russell King, but was
erroneously removed by me when making this option user-selectable in
commit
b09db45c (cpufreq: OMAP driver depends CPUfreq tables.) This
patch remedies that.
Apologies to Russell King for breaking his originally working patch.
Also, thanks to Grazvydas Ignotas for reporting the same problem.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 13 Apr 2012 19:41:21 +0000 (12:41 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc fixes from David Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Eliminate obsolete __handle_softirq() function
sparc64: Fix bootup crash on sun4v.
Linus Torvalds [Fri, 13 Apr 2012 19:19:41 +0000 (12:19 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon patches from Guenter Roeck:
"Fix build warnings in four drivers"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pmbus_core) Fix compiler warning
hwmon: (smsc47m1) Fix compiler warning
hwmon: (acpi_power_meter) Fix compiler warning seen in some configurations
hwmon: (smsc47b397) Fix compiler warning
Linus Torvalds [Fri, 13 Apr 2012 19:18:20 +0000 (12:18 -0700)]
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO bug fixes from Grant Likely:
"Miscellaneous bug fixes to GPIO drivers and for a corner case in the
gpio device tree parsing code."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warning in gpio-samsung.c file
gpio: Fix range check in of_gpio_simple_xlate()
gpio: Fix uninitialized variable bit in adp5588_irq_handler
gpio/sodaville: Convert sodaville driver to new irqdomain API
Linus Torvalds [Fri, 13 Apr 2012 19:17:45 +0000 (12:17 -0700)]
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI bug fixes from Grant Likely:
"Miscellaneous driver bug fixes. No major changes in this branch."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/imx: prevent NULL pointer dereference in spi_imx_probe()
spi/imx: mark base member in spi_imx_data as __iomem
spi/mpc83xx: fix NULL pdata dereference bug
spi/davinci: Fix DMA API usage in davinci
spi/pL022: include types.h to remove compilation warnings
Paul E. McKenney [Fri, 13 Apr 2012 03:35:13 +0000 (03:35 +0000)]
sparc64: Eliminate obsolete __handle_softirq() function
The invocation of softirq is now handled by irq_exit(), so there is no
need for sparc64 to invoke it on the trap-return path. In fact, doing so
is a bug because if the trap occurred in the idle loop, this invocation
can result in lockdep-RCU failures. The problem is that RCU ignores idle
CPUs, and the sparc64 trap-return path to the softirq handlers fails to
tell RCU that the CPU must be considered non-idle while those handlers
are executing. This means that RCU is ignoring any RCU read-side critical
sections in those handlers, which in turn means that RCU-protected data
can be yanked out from under those read-side critical sections.
The shiny new lockdep-RCU ability to detect RCU read-side critical sections
that RCU is ignoring located this problem.
The fix is straightforward: Make sparc64 stop manually invoking the
softirq handlers.
Reported-by: Meelis Roos <mroos@linux.ee>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 13 Apr 2012 18:56:22 +0000 (11:56 -0700)]
sparc64: Fix bootup crash on sun4v.
The DS driver registers as a subsys_initcall() but this can be too
early, in particular this risks registering before we've had a chance
to allocate and setup module_kset in kernel/params.c which is
performed also as a subsyts_initcall().
Register DS using device_initcall() insteal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: stable@vger.kernel.org
Al Viro [Fri, 13 Apr 2012 17:49:47 +0000 (13:49 -0400)]
lockd: fix the endianness bug
comparing be32 values for < is not doing the right thing...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David Brown [Thu, 12 Apr 2012 18:36:50 +0000 (11:36 -0700)]
ARM: msm: Fix section mismatches in proc_comm.c
The change
commit
4416e9eb0b4859b3d28016c5fd0a609bdcbc8a2a
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:12 2010 -0700
arm: msm: Fix section mismatch in smd.c.
fixes a section mismatch between the board file and the smd driver's
probe function, however, it misses the additional mismatches between
the probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
David Brown [Thu, 12 Apr 2012 18:36:50 +0000 (11:36 -0700)]
video: msm: Fix section mismatches in mddi.c
The change
commit
461cbe77d0a4f887c33a3a95ea68a7daf23b4302
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:13 2010 -0700
video: msm: Fix section mismatch in mddi.c.
fixes a section mismatch between the board file and the driver's probe
function, however, it misses the additional mismatches between the
probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
Daniel Walker [Thu, 12 Apr 2012 15:45:37 +0000 (08:45 -0700)]
arm: msm: trout: fix compile failure
Fixes the following warnings,
arch/arm/mach-msm/board-trout.c: In function 'trout_init':
arch/arm/mach-msm/board-trout.c:71: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout.c:71: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout.c:71: error: for each function it appears in.)
and
arch/arm/mach-msm/board-trout-panel.c: In function 'trout_init_panel':
arch/arm/mach-msm/board-trout-panel.c:267: error: 'system_rev' undeclared (first use in this function)
arch/arm/mach-msm/board-trout-panel.c:267: error: (Each undeclared identifier is reported only once
arch/arm/mach-msm/board-trout-panel.c:267: error: for each function it appears in.)
This came in with the following commit
9f97da78bf018206fb623cd351d454af2f105fe0
which removes asm/system.h
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
cc: David Howells <dhowells@redhat.com>
cc: Bryan Huntsman <bryanh@codeaurora.org>
cc: linux-arm-msm@vger.kernel.org
cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David Brown <davidb@codeaurora.org>
Daniel Walker [Thu, 12 Apr 2012 04:04:02 +0000 (21:04 -0700)]
arm: msm: halibut: remove unneeded fixup
This old fixup causes a build failure, so I remove it just like in
trout.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
Chris Metcalf [Wed, 11 Apr 2012 16:21:39 +0000 (12:21 -0400)]
irq_work: fix compile failure on tile from missing include
Building with IRQ_WORK configured results in
kernel/irq_work.c: In function ‘irq_work_run’:
kernel/irq_work.c:110: error: implicit declaration of function ‘irqs_disabled’
The appropriate header just needs to be included.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Tue, 3 Apr 2012 17:51:35 +0000 (13:51 -0400)]
ia64: populate the cmpxchg header with appropriate code
commit
93f378883cecb9dcb2cf5b51d9d24175906659da
"Fix ia64 build errors (fallout from system.h disintegration)"
introduced arch/ia64/include/asm/cmpxchg.h as a temporary
build fix and stated:
"... leave the migration of xchg() and cmpxchg() to this new
header file for a future patch."
Migrate the appropriate chunks from asm/intrinsics.h and fix
the whitespace issues in the migrated chunk.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Mon, 2 Apr 2012 20:04:13 +0000 (16:04 -0400)]
alpha: fix build failures from system.h dismemberment
commit
ec2212088c42ff7d1362629ec26dda4f3e8bdad3
"Disintegrate asm/system.h for Alpha"
combined with commit
b4816afa3986704d1404fc48e931da5135820472
"Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h"
introduced the concept of asm/cmpxchg.h but the alpha arch
never got one. Fork the cmpxchg content out of the asm/atomic.h
file to create one.
Some minor whitespace fixups were done on the block of code that
created the new file.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Al Viro [Fri, 13 Apr 2012 16:30:02 +0000 (12:30 -0400)]
ocfs2: ->e_leaf_clusters endianness breakage
le16, not le32...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 13 Apr 2012 16:28:21 +0000 (12:28 -0400)]
ocfs2: ->rl_count endianness breakage
le16, not le32...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 13 Apr 2012 16:27:11 +0000 (12:27 -0400)]
ocfs: ->rl_used breakage on big-endian
it's le16, not le32 or le64...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 13 Apr 2012 16:22:00 +0000 (12:22 -0400)]
ocfs2: ->l_next_free_req breakage on big-endian
It's le16, not le32...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 13 Apr 2012 15:49:04 +0000 (11:49 -0400)]
btrfs: btrfs_root_readonly() broken on big-endian
->root_flags is __le64 and all accesses to it go through the helpers
that do proper conversions. Except for btrfs_root_readonly(), which
checks bit 0 as in host-endian...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Sachin Prabhu [Fri, 13 Apr 2012 13:04:32 +0000 (14:04 +0100)]
Fix number parsing in cifs_parse_mount_options
The function kstrtoul() used to parse number strings in the mount
option parser is set to expect a base 10 number . This treats the octal
numbers passed for mount options such as file_mode as base10 numbers
leading to incorrect behavior.
Change the 'base' argument passed to kstrtoul from 10 to 0 to
allow it to auto-detect the base of the number passed.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Acked-by: Jeff Layton <jlayton@samba.org>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Al Viro [Fri, 13 Apr 2012 00:32:25 +0000 (20:32 -0400)]
ext4: fix endianness breakage in ext4_split_extent_at()
->ee_len is __le16, so assigning cpu_to_le32() to it is going to do
Bad Things(tm) on big-endian hosts...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 13 Apr 2012 04:32:14 +0000 (00:32 -0400)]
nfsd: fix compose_entry_fh() failure exits
Restore the original logics ("fail on mountpoints, negatives and in
case of fh_compose() failures"). Since commit 8177e (nfsd: clean up
readdirplus encoding) that got broken -
rv = fh_compose(fhp, exp, dchild, &cd->fh);
if (rv)
goto out;
if (!dchild->d_inode)
goto out;
rv = 0;
out:
is equivalent to
rv = fh_compose(fhp, exp, dchild, &cd->fh);
out:
and the second check has no effect whatsoever...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 13 Apr 2012 04:15:37 +0000 (00:15 -0400)]
nfsd: fix error value on allocation failure in nfsd4_decode_test_stateid()
PTR_ERR(NULL) is going to be 0...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 13 Apr 2012 04:10:34 +0000 (00:10 -0400)]
nfsd: fix endianness breakage in TEST_STATEID handling
->ts_id_status gets nfs errno, i.e. it's already big-endian; no need
to apply htonl() to it. Broken by commit 174568 (NFSD: Added TEST_STATEID
operation) last year...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 13 Apr 2012 04:00:04 +0000 (00:00 -0400)]
nfsd: fix error values returned by nfsd4_lockt() when nfsd_open() fails
nfsd_open() already returns an NFS error value; only vfs_test_lock()
result needs to be fed through nfserrno(). Broken by commit 55ef12
(nfsd: Ensure nfsv4 calls the underlying filesystem on LOCKT)
three years ago...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 13 Apr 2012 03:47:00 +0000 (23:47 -0400)]
nfsd: fix b0rken error value for setattr on read-only mount
..._want_write() returns -EROFS on failure, _not_ an NFS error value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Will Deacon [Thu, 12 Apr 2012 16:16:01 +0000 (17:16 +0100)]
ARM: 7383/1: nommu: populate vectors page from paging_init
Commit
94e5a85b ("ARM: earlier initialization of vectors page") made it
the responsibility of paging_init to initialise the vectors page.
This patch adds a call to early_trap_init for the !CONFIG_MMU case,
placing the vectors at CONFIG_VECTORS_BASE.
Cc: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Thu, 12 Apr 2012 16:12:37 +0000 (17:12 +0100)]
ARM: 7381/1: nommu: fix typo in mm/Kconfig
The description for the CPU_HIGH_VECTOR Kconfig option for nommu builds
doesn't make any sense.
This patch fixes up the trivial grammatical error.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Marc Zyngier [Wed, 11 Apr 2012 13:52:56 +0000 (14:52 +0100)]
ARM: 7380/1: DT: do not add a zero-sized memory property
Some bootloaders are broken enough to expose an ATAG_MEM with
a null size. Converting such tag to a memory node leads to
an unbootable system.
Skip over zero sized ATAG_MEM to avoid this situation.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Marc Zyngier [Wed, 11 Apr 2012 13:52:55 +0000 (14:52 +0100)]
ARM: 7379/1: DT: fix atags_to_fdt() second call site
atags_to_fdt() returns 1 when it fails to find a valid FDT signature.
The CONFIG_ARM_ATAG_DTB_COMPAT code is supposed to retry with another
location, but only does so when the initial call doesn't fail.
Fix this by using the correct condition in the assembly code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mark Brown [Fri, 13 Apr 2012 12:11:50 +0000 (13:11 +0100)]
ARM: 7366/3: amba: Remove AMBA level regulator support
The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).
Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.
This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does). Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ingo Molnar [Fri, 13 Apr 2012 07:47:04 +0000 (09:47 +0200)]
Merge tag 'perf-urgent-for-mingo' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull various perf tooling fixes from Arnaldo Carvalho de Melo.
Jesper Juhl [Thu, 12 Apr 2012 20:11:25 +0000 (22:11 +0200)]
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
In sound/pci/hda/patch_realtek.c::alc_auto_fill_dac_nids(), in the
'for (;;)' loop, if the 'badness' value returned from
fill_and_eval_dacs() is negative, then we'll return from the function
without freeing the memory we allocated for 'best_cfg', thus leaking.
Fix the leak by kfree()'ing the memory when badness is negative.
While I was there I also noticed some trailing whitespace in the
function that I removed (along with all other trailing whitespace in
the file) - it didn't seem worth-while to do that as two patches, so I
hope it's OK that I just did it all as one patch.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Fri, 13 Apr 2012 01:51:32 +0000 (18:51 -0700)]
Merge tag 'srpt-srq-type' of git://git./linux/kernel/git/roland/infiniband
Pull infiniband fix from Roland Dreier:
"Add a fix for a bug hit by Alexey Shvetsov in ib_srtp that hits on
non-mlx4 hardware."
* tag 'srpt-srq-type' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/srpt: Set srq_type to IB_SRQT_BASIC
Paul Gortmaker [Thu, 12 Apr 2012 23:46:34 +0000 (19:46 -0400)]
kconfig: delete last traces of __enabled_ from autoconf.h
We've now fixed IS_ENABLED() and friends to not require any special
"__enabled_" prefixed versions of the normal Kconfig options, so delete
the last traces of them being generated.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Gortmaker [Thu, 12 Apr 2012 23:46:33 +0000 (19:46 -0400)]
Revert "kconfig: fix __enabled_ macros definition for invisible and un-selected symbols"
This reverts commit
953742c8fe8ac45be453fee959d7be40cd89f920.
Dumping two lines into autoconf.h for all existing Kconfig options
results in a giant file (~16k lines) we have to process each time we
compile something. We've weaned IS_ENABLED() and similar off of
requiring the __enabled_ definitions so now we can revert the change
which caused all the extra lines.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Gortmaker [Thu, 12 Apr 2012 23:46:32 +0000 (19:46 -0400)]
kconfig: fix IS_ENABLED to not require all options to be defined
Using IS_ENABLED() within C (vs. within CPP #if statements) in its
current form requires us to actually define every possible bool/tristate
Kconfig option twice (__enabled_* and __enabled_*_MODULE variants).
This results in a huge autoconf.h file, on the order of 16k lines for a
x86_64 defconfig.
Fixing IS_ENABLED to be able to work on the smaller subset of just
things that we really have defined is step one to fixing this. Which
means it has to not choke when fed non-enabled options, such as:
include/linux/netdevice.h:964:1: warning: "__enabled_CONFIG_FCOE_MODULE" is not defined [-Wundef]
The original prototype of how to implement a C and preprocessor
compatible way of doing this came from the Google+ user "comex ." in
response to Linus' crowdsourcing challenge for a possible improvement on
his earlier C specific solution:
#define config_enabled(x) (__stringify(x)[0] == '1')
In this implementation, I've chosen variable names that hopefully make
how it works more understandable.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Josef Bacik [Thu, 12 Apr 2012 20:03:57 +0000 (16:03 -0400)]
Btrfs: use commit root when loading free space cache
A user reported that booting his box up with btrfs root on 3.4 was way
slower than on 3.3 because I removed the ideal caching code. It turns out
that we don't load the free space cache if we're in a commit for deadlock
reasons, but since we're reading the cache and it hasn't changed yet we are
safe reading the inode and free space item from the commit root, so do that
and remove all of the deadlock checks so we don't unnecessarily skip loading
the free space cache. The user reported this fixed the slowness. Thanks,
Tested-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Thu, 12 Apr 2012 22:37:21 +0000 (15:37 -0700)]
Merge tag 'usb-3.4-rc2' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of fixes for the USB core and drivers for 3.4-rc2
Lots of tiny xhci fixes here, a few usb-serial driver fixes and new
device ids, and a smattering of other minor fixes in different USB
drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (30 commits)
USB: update usbtmc api documentation
xHCI: Correct the #define XHCI_LEGACY_DISABLE_SMI
xHCI: use gfp flags from caller instead of GFP_ATOMIC
xHCI: add XHCI_RESET_ON_RESUME quirk for VIA xHCI host
USB: fix bug of device descriptor got from superspeed device
xhci: Fix register save/restore order.
xhci: Restore event ring dequeue pointer on resume.
xhci: Don't write zeroed pointers to xHC registers.
xhci: Warn when hosts don't halt.
xhci: don't re-enable IE constantly
usb: xhci: fix section mismatch in linux-next
xHCI: correct to print the true HSEE of USBCMD
USB: serial: fix race between probe and open
UHCI: hub_status_data should indicate if ports are resuming
EHCI: keep track of ports being resumed and indicate in hub_status_data
USB: fix race between root-hub suspend and remote wakeup
USB: sierra: add support for Sierra Wireless MC7710
USB: ftdi_sio: fix race condition in TIOCMIWAIT, and abort of TIOCMIWAIT when the device is removed
USB: ftdi_sio: fix status line change handling for TIOCMIWAIT and TIOCGICOUNT
USB: don't ignore suspend errors for root hubs
...
Linus Torvalds [Thu, 12 Apr 2012 22:36:33 +0000 (15:36 -0700)]
Merge tag 'tty-3.4-rc2' of git://git./linux/kernel/git/gregkh/tty
Pull tty and serial fixes from Greg KH:
"Here are some tty and serial fixes for 3.4-rc2.
Most important here is the pl011 fix, which has been reported by about
100 different people, which means more people use it than I expected
:)
There are also some 8250 driver reverts due to some problems reported
by them. And other minor fixes as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
pch_uart: Add Kontron COMe-mTT10 uart clock quirk
pch_uart: Fix MSI setting issue
serial/8250_pci: add a "force background timer" flag and use it for the "kt" serial port
Revert "serial/8250_pci: setup-quirk workaround for the kt serial controller"
Revert "serial/8250_pci: init-quirk msi support for kt serial controller"
tty/serial/omap: console can only be built-in
serial: samsung: fix omission initialize ulcon in reset port fn()
printk(): add KERN_CONT where needed in hpet and vt code
tty/serial: atmel_serial: fix RS485 half-duplex problem
tty: serial: altera_uart: Check for NULL platform_data in probe.
isdn/gigaset: use gig_dbg() for debugging output
omap-serial: Fix the error handling in the omap_serial probe
serial: PL011: move interrupt clearing
Linus Torvalds [Thu, 12 Apr 2012 22:35:12 +0000 (15:35 -0700)]
Merge tag 'staging-3.4-rc2' of git://git./linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg KH:
"Here are a number of bugfixes for the drivers/staging/ portion of the
kernel that have been reported recently.
Nothing major here, with maybe the exception of the ramster code can
now be built so it is enabled in the build again, and lots of memory
leaks that people like to have fixed on their systems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: fix mem leaks in __persistent_ram_init()
staging: vt6656: Don't leak memory in drivers/staging/vt6656/ioctl.c::private_ioctl()
staging: iio: hmc5843: Fix crash in probe function.
staging/xgifb: fix display on XGI Volari Z11m cards
Staging: android: timed_gpio: Fix resource leak in timed_gpio_probe error paths
android: make persistent_ram based drivers depend on HAVE_MEMBLOCK
staging: iio: ak8975: Remove i2c client data corruption
staging: drm/omap: move where DMM driver is registered
staging: zsmalloc: fix memory leak
Staging: rts_pstor: off by one in for loop
staging: ozwpan: Added new maintainer for ozwpan
staging:rts_pstor:Avoid "Bad target number" message when probing driver
staging:rts_pstor:Fix possible panic by NULL pointer dereference
Staging: vt6655-6: check keysize before memcpy()
staging/media/as102: Don't call release_firmware() on uninitialized variable
staging:iio:core add missing increment of loop index in iio_map_array_unregister()
staging: ramster: unbreak my heart
staging/vme: Fix module parameters
staging: sep: Fix sign of error
Linus Torvalds [Thu, 12 Apr 2012 22:34:33 +0000 (15:34 -0700)]
Merge tag 'driver-core-3.4-rc2' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core and kobject fixes from Greg KH:
"Here are some minor fixes for the driver core and kobjects that people
have reported recently.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: provide more diagnostic info for kobject_add_internal() failures
sysfs: handle 'parent deleted before child added'
sysfs: Prevent crash on unset sysfs group attributes
sysfs: Update the name hash for an entry after changing the namespace
drivers/base: fix compiler warning in SoC export driver - idr should be ida
drivers/base: Remove unneeded spin_lock_init call for soc_lock
Linus Torvalds [Thu, 12 Apr 2012 22:33:16 +0000 (15:33 -0700)]
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull a fix for the recent irqdomain bug fixes from Grant Likely:
"I flubbed one patch in the last pull request which broke a format
string on 64 bit platforms. Here's the fix."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6:
irq_domain: fix type mismatch in debugfs output format
Grant Likely [Thu, 12 Apr 2012 20:42:15 +0000 (14:42 -0600)]
irq_domain: fix type mismatch in debugfs output format
sizeof(void*) returns an unsigned long, but it was being used as a width parameter to a "%-*s" format string which requires an int. On 64 bit platforms this causes a type mismatch:
linux/kernel/irq/irqdomain.c:575: warning: field width should have type
'int', but argument 6 has type 'long unsigned int'
This change casts the size to an int so printf gets the right data type.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Daney <david.daney@cavium.com>
Linus Torvalds [Thu, 12 Apr 2012 22:20:24 +0000 (15:20 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull trivial perf build failure fix from Thomas Gleixner.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Fix getrusage() related build failure on glibc trunk
Linus Torvalds [Thu, 12 Apr 2012 22:16:26 +0000 (15:16 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"The itimer removal one is not strictly a fix, but I really wanted to
avoid a rebase of the urgent ones."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource: Load the ACPI PM clocksource asynchronously"
clockevents: tTack broadcast device mode change in tick_broadcast_switch_to_oneshot()
itimer: Use printk_once instead of WARN_ONCE
nohz: Fix stale jiffies update in tick_nohz_restart()
tick: Document TICK_ONESHOT config option
proc: stats: Use arch_idle_time for idle and iowait times if available
itimer: Schedule silent NULL pointer fixup in setitimer() for removal
Linus Torvalds [Thu, 12 Apr 2012 22:06:07 +0000 (15:06 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Use correct byte-sized register constraint in __add()
x86: Use correct byte-sized register constraint in __xchg_op()
x86: vsyscall: Use NULL instead 0 for a pointer argument
Jesper Juhl [Wed, 11 Apr 2012 20:10:20 +0000 (22:10 +0200)]
staging: android: fix mem leaks in __persistent_ram_init()
If, in __persistent_ram_init(), the call to
persistent_ram_buffer_init() fails or the call to
persistent_ram_init_ecc() fails then we fail to free the memory we
allocated to 'prz' with kzalloc() - thus leaking it.
To prevent the leaks I consolidated all error exits from the function
at a 'err:' label at the end and made all error cases jump to that
label where we can then make sure we always free 'prz'. This is safe
since all the situations where the code bails out happen before 'prz'
has been stored anywhere and although we'll do a redundant kfree(NULL)
call in the case of kzalloc() itself failing that's OK since kfree()
deals gracefully with NULL pointers and I felt it was more important
to keep all error exits at a single location than to avoid that one
harmless/redundant kfree() on a error path.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Colin Cross <ccross@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesper Juhl [Wed, 11 Apr 2012 22:35:46 +0000 (00:35 +0200)]
staging: vt6656: Don't leak memory in drivers/staging/vt6656/ioctl.c::private_ioctl()
If copy_to_user() fails in the WLAN_CMD_GET_NODE_LIST case of the
switch in drivers/staging/vt6656/ioctl.c::private_ioctl() we'll leak
the memory allocated to 'pNodeList'. Fix that by kfree'ing the memory
in the failure case.
Also remove a pointless cast (to type 'PSNodeList') of a kmalloc()
return value - kmalloc() returns a void pointer that is implicitly
converted, so there is no need for an explicit cast.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Belisko [Thu, 12 Apr 2012 19:48:03 +0000 (21:48 +0200)]
staging: iio: hmc5843: Fix crash in probe function.
Fix crash after issuing:
echo hmc5843 0x1e > /sys/class/i2c-dev/i2c-2/device/new_device
[ 37.180999] device: '2-001e': device_add
[ 37.188293] bus: 'i2c': add device 2-001e
[ 37.194549] PM: Adding info for i2c:2-001e
[ 37.200958] bus: 'i2c': driver_probe_device: matched device 2-001e with driver hmc5843
[ 37.210815] bus: 'i2c': really_probe: probing driver hmc5843 with device 2-001e
[ 37.224884] HMC5843 initialized
[ 37.228759] ------------[ cut here ]------------
[ 37.233612] kernel BUG at mm/slab.c:505!
[ 37.237701] Internal error: Oops - BUG: 0 [#1] PREEMPT
[ 37.243103] Modules linked in:
[ 37.246337] CPU: 0 Not tainted (3.3.1-gta04+ #28)
[ 37.251647] PC is at kfree+0x84/0x144
[ 37.255493] LR is at kfree+0x20/0x144
[ 37.259338] pc : [<
c00b408c>] lr : [<
c00b4028>] psr:
40000093
[ 37.259368] sp :
de249cd8 ip :
0000000c fp :
00000090
[ 37.271362] r10:
0000000a r9 :
de229eac r8 :
c0236274
[ 37.276855] r7 :
c09d6490 r6 :
a0000013 r5 :
de229c00 r4 :
de229c10
[ 37.283691] r3 :
c0f00218 r2 :
00000400 r1 :
c0eea000 r0 :
c00b4028
[ 37.290527] Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
[ 37.298095] Control:
10c5387d Table:
9e1d0019 DAC:
00000015
[ 37.304107] Process sh (pid: 91, stack limit = 0xde2482f0)
[ 37.309844] Stack: (0xde249cd8 to 0xde24a000)
[ 37.314422] 9cc0:
de229c10 de229c00
[ 37.322998] 9ce0:
de229c10 ffffffea 00000005 c0236274 de140a80 c00b4798 dec00080 de140a80
[ 37.331573] 9d00:
c032f37c dec00080 000080d0 00000001 de229c00 de229c10 c048d578 00000005
[ 37.340148] 9d20:
de229eac 0000000a 00000090 c032fa40 00000001 00000000 00000001 de229c10
[ 37.348724] 9d40:
de229eac 00000029 c075b558 00000001 00000003 00000004 de229c10 c048d594
[ 37.357299] 9d60:
00000000 60000013 00000018 205b0007 37332020 3432322e 5d343838 c0060020
[ 37.365905] 9d80:
de251600 00000001 00000000 de251600 00000001 c0065a84 de229c00 de229c48
[ 37.374481] 9da0:
00000006 0048d62c de229c38 de229c00 de229c00 de1f6c00 de1f6c20 00000001
[ 37.383056] 9dc0:
00000000 c048d62c 00000000 de229c00 de229c00 de1f6c00 de1f6c20 00000001
[ 37.391632] 9de0:
00000000 c048d62c 00000000 c0330164 00000000 de1f6c20 c048d62c de1f6c00
[ 37.400207] 9e00:
c0330078 de1f6c04 c078d714 de189b58 00000000 c02ccfd8 de1f6c20 c0795f40
[ 37.408782] 9e20:
c0238330 00000000 00000000 c02381a8 de1b9fc0 de1f6c20 de1f6c20 de249e48
[ 37.417358] 9e40:
c0238330 c0236bb0 decdbed8 de7d0f14 de1f6c20 de1f6c20 de1f6c54 de1f6c20
[ 37.425933] 9e60:
00000000 c0238030 de1f6c20 c078d7bc de1f6c20 c02377ec de1f6c20 de1f6c28
[ 37.434509] 9e80:
dee64cb0 c0236138 c047c554 de189b58 00000000 c004b45c de1f6c20 de1f6cd8
[ 37.443084] 9ea0:
c0edfa6c de1f6c00 dee64c68 de1f6c04 de1f6c20 dee64cb8 c047c554 de189b58
[ 37.451690] 9ec0:
00000000 c02cd634 dee64c68 de249ef4 de23b008 dee64cb0 0000000d de23b000
[ 37.460266] 9ee0:
de23b007 c02cd78c 00000002 00000000 00000000 35636d68 00333438 00000000
[ 37.468841] 9f00:
00000000 00000000 001e0000 00000000 00000000 00000000 00000000 0a10cec0
[ 37.477416] 9f20:
00000002 de249f80 0000000d dee62990 de189b40 c0234d88 0000000d c010c354
[ 37.485992] 9f40:
0000000d de210f28 000acc88 de249f80 0000000d de248000 00000000 c00b7bf8
[ 37.494567] 9f60:
de210f28 000acc88 de210f28 000acc88 00000000 00000000 0000000d c00b7ed8
[ 37.503143] 9f80:
00000000 00000000 0000000d 00000000 0007fa28 0000000d 000acc88 00000004
[ 37.511718] 9fa0:
c000e544 c000e380 0007fa28 0000000d 00000001 000acc88 0000000d 00000000
[ 37.520294] 9fc0:
0007fa28 0000000d 000acc88 00000004 00000001 00000020 00000002 00000000
[ 37.528869] 9fe0:
00000000 beab8624 0000ea05 b6eaebac 600d0010 00000001 00000000 00000000
[ 37.537475] [<
c00b408c>] (kfree+0x84/0x144) from [<
c0236274>] (device_add+0x530/0x57c)
[ 37.545806] [<
c0236274>] (device_add+0x530/0x57c) from [<
c032fa40>] (iio_device_register+0x8c8/0x990)
[ 37.555480] [<
c032fa40>] (iio_device_register+0x8c8/0x990) from [<
c0330164>] (hmc5843_probe+0xec/0x114)
[ 37.565338] [<
c0330164>] (hmc5843_probe+0xec/0x114) from [<
c02ccfd8>] (i2c_device_probe+0xc4/0xf8)
[ 37.574737] [<
c02ccfd8>] (i2c_device_probe+0xc4/0xf8) from [<
c02381a8>] (driver_probe_device+0x118/0x218)
[ 37.584777] [<
c02381a8>] (driver_probe_device+0x118/0x218) from [<
c0236bb0>] (bus_for_each_drv+0x4c/0x84)
[ 37.594818] [<
c0236bb0>] (bus_for_each_drv+0x4c/0x84) from [<
c0238030>] (device_attach+0x78/0xa4)
[ 37.604125] [<
c0238030>] (device_attach+0x78/0xa4) from [<
c02377ec>] (bus_probe_device+0x28/0x9c)
[ 37.613433] [<
c02377ec>] (bus_probe_device+0x28/0x9c) from [<
c0236138>] (device_add+0x3f4/0x57c)
[ 37.622650] [<
c0236138>] (device_add+0x3f4/0x57c) from [<
c02cd634>] (i2c_new_device+0xf8/0x19c)
[ 37.631805] [<
c02cd634>] (i2c_new_device+0xf8/0x19c) from [<
c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130)
[ 37.641754] [<
c02cd78c>] (i2c_sysfs_new_device+0xb4/0x130) from [<
c0234d88>] (dev_attr_store+0x18/0x24)
[ 37.651611] [<
c0234d88>] (dev_attr_store+0x18/0x24) from [<
c010c354>] (sysfs_write_file+0x10c/0x140)
[ 37.661193] [<
c010c354>] (sysfs_write_file+0x10c/0x140) from [<
c00b7bf8>] (vfs_write+0xb0/0x178)
[ 37.670410] [<
c00b7bf8>] (vfs_write+0xb0/0x178) from [<
c00b7ed8>] (sys_write+0x3c/0x68)
[ 37.678833] [<
c00b7ed8>] (sys_write+0x3c/0x68) from [<
c000e380>] (ret_fast_syscall+0x0/0x3c)
[ 37.687683] Code:
1593301c e5932000 e3120080 1a000000 (
e7f001f2)
[ 37.700775] ---[ end trace
aaf805debdb69390 ]---
Client data was assigned to iio_dev structure in probe but in
hmc5843_init_client function casted to private driver data structure which
is wrong. Possibly calling mutex_init(&data->lock); corrupt data
which the lead to above crash.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 12 Apr 2012 21:15:21 +0000 (14:15 -0700)]
Merge branch 'akpm' (Andrew's patch-bomb)
Merge fixes from Andrew Morton.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (14 patches)
panic: fix stack dump print on direct call to panic()
drivers/rtc/rtc-pl031.c: enable clock on all ST variants
Revert "mm: vmscan: fix misused nr_reclaimed in shrink_mem_cgroup_zone()"
hugetlb: fix race condition in hugetlb_fault()
drivers/rtc/rtc-twl.c: use static register while reading time
drivers/rtc/rtc-s3c.c: add placeholder for driver private data
drivers/rtc/rtc-s3c.c: fix compilation error
MAINTAINERS: add PCDP console maintainer
memcg: do not open code accesses to res_counter members
drivers/rtc/rtc-efi.c: fix section mismatch warning
drivers/rtc/rtc-r9701.c: reset registers if invalid values are detected
drivers/char/random.c: fix boot id uniqueness race
memcg: fix broken boolen expression
memcg: fix up documentation on global LRU