OSDN Git Service
Christian Lamparter [Tue, 25 Jun 2019 08:41:51 +0000 (10:41 +0200)]
net: dsa: qca8k: introduce reset via gpio feature
The QCA8337(N) has a RESETn signal on Pin B42 that
triggers a chip reset if the line is pulled low.
The datasheet says that: "The active low duration
must be greater than 10 ms".
This can hopefully fix some of the issues related
to pin strapping in OpenWrt for the EA8500 which
suffers from detection issues after a SoC reset.
Please note that the qca8k_probe() function does
currently require to read the chip's revision
register for identification purposes.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Lamparter [Tue, 25 Jun 2019 08:41:50 +0000 (10:41 +0200)]
dt-bindings: net: dsa: qca8k: document reset-gpios property
This patch documents the qca8k's reset-gpios property that
can be used if the QCA8337N ends up in a bad state during
reset.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 24 Jun 2019 20:44:51 +0000 (13:44 -0700)]
ipv6: Convert gateway validation to use fib6_info
Gateway validation does not need a dst_entry, it only needs the fib
entry to validate the gateway resolution and egress device. So,
convert ip6_nh_lookup_table from ip6_pol_route to fib6_table_lookup
and ip6_route_check_nh to use fib6_lookup over rt6_lookup.
ip6_pol_route is a call to fib6_table_lookup and if successful a call
to fib6_select_path. From there the exception cache is searched for an
entry or a dst_entry is created to return to the caller. The exception
entry is not relevant for gateway validation, so what matters are the
calls to fib6_table_lookup and then fib6_select_path.
Similarly, rt6_lookup can be replaced with a call to fib6_lookup with
RT6_LOOKUP_F_IFACE set in flags. Again, the exception cache search is
not relevant, only the lookup with path selection. The primary difference
in the lookup paths is the use of rt6_select with fib6_lookup versus
rt6_device_match with rt6_lookup. When you remove complexities in the
rt6_select path, e.g.,
1. saddr is not set for gateway validation, so RT6_LOOKUP_F_HAS_SADDR
is not relevant
2. rt6_check_neigh is not called so that removes the RT6_NUD_FAIL_DO_RR
return and round-robin logic.
the code paths are believed to be equivalent for the given use case -
validate the gateway and optionally given the device. Furthermore, it
aligns the validation with onlink code path and the lookup path actually
used for rx and tx.
Adjust the users, ip6_route_check_nh_onlink and ip6_route_check_nh to
handle a fib6_info vs a rt6_info when performing validation checks.
Existing selftests fib-onlink-tests.sh and fib_tests.sh are used to
verify the changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Jun 2019 18:03:22 +0000 (11:03 -0700)]
Merge branch 'FDB-VLAN-and-PTP-fixes-for-SJA1105-DSA'
Vladimir Oltean says:
====================
FDB, VLAN and PTP fixes for SJA1105 DSA
This patchset is an assortment of fixes for the net-next version of the
sja1105 DSA driver:
- Avoid a kernel panic when the driver fails to probe or unregisters
- Finish Arnd Bermann's idea of compiling PTP support as part of the
main DSA driver and not separately
- Better handling of initial port-based VLAN as well as VLANs for
dsa_8021q FDB entries
- Fix address learning for the SJA1105 P/Q/R/S family
- Make static FDB entries persistent across switch resets
- Fix reporting of statically-added FDB entries in 'bridge fdb show'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:42 +0000 (02:39 +0300)]
net: dsa: sja1105: Implement is_static for FDB entries on E/T
The first generation switches don't tell us through the dynamic config
interface whether the dumped FDB entries are static or not (the LOCKEDS
bit from P/Q/R/S).
However, now that we're keeping a mirror of all 'bridge fdb' commands in
the static config, this is an opportunity to compare a dumped FDB entry
to the driver's private database. After all, what makes an entry static
is that *we* added it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:41 +0000 (02:39 +0300)]
net: dsa: sja1105: Use correct dsa_8021q VIDs for FDB commands
A FDB entry means that "frames that match this VID and DMAC must be
forwarded to this port".
In the case of dsa_8021q however, the VID is not a single one (and
neither two, as my previous patch assumed). The VID can be set either by
the CPU port (1 tx_vid), or by any of the other front-panel port (n-1
rx_vid's).
Fixes:
93647594d8f5 ("net: dsa: sja1105: Hide the dsa_8021q VLANs from the bridge fdb command")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:40 +0000 (02:39 +0300)]
net: dsa: sja1105: Populate is_static for FDB entries on P/Q/R/S
The reason why this wasn't tackled earlier is that I had hoped I
understood the user manual wrong. But unfortunately hacks are required
in order to retrieve the static/dynamic nature of FDB entries on SJA1105
P/Q/R/S, since this info is stored in the writeback buffer of the
dynamic config command.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:39 +0000 (02:39 +0300)]
net: dsa: sja1105: Add a high-level overview of the dynamic config interface
When trying to add support for LOCKEDS (static FDB entries) on SJA1105
P/Q/R/S, at first I didn't remember how the abstraction I created
worked, and actually thought it works by mistake.
To avoid other people staring at the code and not making much sense out
of it, add some comments at the top of the file.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:38 +0000 (02:39 +0300)]
net: dsa: sja1105: Back up static FDB entries in kernel memory
After commit
8456721dd4ec ("net: dsa: sja1105: Add support for
configuring address ageing time"), we started to reset the switch rather
often (each time the bridge core changes the ageing time on a switch
port).
The unfortunate reality is that SJA1105 doesn't have any {cold, warm,
whatever} reset mode in which it accepts a new configuration stream
without flushing the FDB. Instead, in its world, the FDB *is* an
optional part of the static configuration.
So we play its game, and do what we also do for VLANs: for each 'bridge
fdb' command, we add the FDB entry through the dynamic interface, and we
append the in-kernel static config memory with info that we're going to
use later, when the next reset command is going to be issued.
The result is that 'bridge fdb' commands are now persistent (dynamically
learned entries are lost, but that's ok).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:37 +0000 (02:39 +0300)]
net: dsa: sja1105: Make P/Q/R/S learn MAC addresses
At the end of the commit
1da73821343c ("net: dsa: sja1105: Add FDB
operations for P/Q/R/S series") message, I said that:
At the moment only FDB entries installed statically through 'bridge fdb'
are visible in the dump callback - the dynamically learned ones are
still under investigation.
It looks like the reason why they were not visible in 'bridge fdb' was
that they were never learned - always flooded.
SJA1105 P/Q/R/S manual says about the MAXADDRP[port] field:
Specify the maximum number of MAC address dynamically learned from
the respective port. It is used to limit the number of learned MAC
addresses per port.
It looks like not providing a value in the static config (aka providing
zeroes) is enough for it to not store the learned addresses in the FDB.
For now we divide the 1024 entry FDB "equally" amongst the 5 ports. This
may be revisited if the situation calls for that - for now I'm happy
that learning works.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:36 +0000 (02:39 +0300)]
net: dsa: sja1105: Actually implement the P/Q/R/S FDB bits
In commit
1da73821343c ("net: dsa: sja1105: Add FDB operations for
P/Q/R/S series"), these bits were set in the static config, but
apparently they did not do anything. The reason is that the packing
accessors for them were part of a patch I forgot to send.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:35 +0000 (02:39 +0300)]
net: dsa: sja1105: Make vid 1 the default pvid
In SJA1105 there is no concept of 'default values' per se, everything
needs to be driver-supplied through the static configuration tables.
The issue is that the hardware manual says that 'at least the default
untagging VLAN' is mandatory to be provided through the static config.
But VLAN 0 isn't a very good initial pvid - its use is reserved for
priority-tagged frames, and the layers of the stack that care about
those already make sure that this VLAN is installed, as can be seen in
the message below:
8021q: adding VLAN 0 to HW filter on device swp2
So change the pvid provided through the static configuration to 1, which
matches the bridge core's defaults.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:34 +0000 (02:39 +0300)]
net: dsa: sja1105: Cancel PTP delayed work on unregister
Currently when the driver unloads and PTP is enabled, the delayed work
that prevents the timecounter from expiring becomes a ticking time bomb.
The kernel will schedule the work thread within 60 seconds of driver
removal, but the work handler is no longer there, leading to this
strange and inconclusive stack trace:
[ 64.473112] Unable to handle kernel paging request at virtual address
79746970
[ 64.480340] pgd =
008c4af9
[ 64.483042] [
79746970] *pgd=
00000000
[ 64.486620] Internal error: Oops:
80000005 [#1] SMP ARM
[ 64.491820] Modules linked in:
[ 64.494871] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
5.2.0-rc5-01634-ge3a2773ba9e5 #1246
[ 64.503007] Hardware name: Freescale LS1021A
[ 64.507259] PC is at 0x79746970
[ 64.510393] LR is at call_timer_fn+0x3c/0x18c
[ 64.514729] pc : [<
79746970>] lr : [<
c03bd734>] psr:
60010113
[ 64.520965] sp :
c1901de0 ip :
00000000 fp :
c1903080
[ 64.526163] r10:
c1901e38 r9 :
ffffe000 r8 :
c19064ac
[ 64.531363] r7 :
79746972 r6 :
e98dd260 r5 :
00000100 r4 :
c1a9e4a0
[ 64.537859] r3 :
c1900000 r2 :
ffffa400 r1 :
79746972 r0 :
e98dd260
[ 64.544359] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 64.551460] Control:
10c5387d Table:
a8a2806a DAC:
00000051
[ 64.557176] Process swapper/0 (pid: 0, stack limit = 0x1ddb27f0)
[ 64.563147] Stack: (0xc1901de0 to 0xc1902000)
[ 64.567481] 1de0:
eb6a4918 3d60d7c3 c1a9e554 e98dd260 eb6a34c0 c1a9e4a0 ffffa400 c19064ac
[ 64.575616] 1e00:
ffffe000 c03bd95c c1901e34 c1901e34 eb6a34c0 c1901e30 c1903d00 c186f4c0
[ 64.583751] 1e20:
c1906488 29e34000 c1903080 c03bdca4 00000000 eaa6f218 00000000 eb6a45c0
[ 64.591886] 1e40:
eb6a45c0 20010193 00000003 c03c0a68 20010193 3f7231be c1903084 00000002
[ 64.600022] 1e60:
00000082 00000001 ffffe000 c1a9e0a4 00000100 c0302298 02b64722 0000000f
[ 64.608157] 1e80:
c186b3c8 c1877540 c19064ac 0000000a c186b350 ffffa401 c1903d00 c1107348
[ 64.616292] 1ea0:
00200102 c0d87a14 ea823c00 ffffe000 00000012 00000000 00000000 ea810800
[ 64.624427] 1ec0:
f0803000 c1876ba8 00000000 c034c784 c18774b8 c039fb50 c1906c90 c1978aac
[ 64.632562] 1ee0:
f080200c f0802000 c1901f10 c0709ca8 c03091a0 60010013 ffffffff c1901f44
[ 64.640697] 1f00:
00000000 c1900000 c1876ba8 c0301a8c 00000000 000070a0 eb6ac1a0 c031da60
[ 64.648832] 1f20:
ffffe000 c19064ac c19064f0 00000001 00000000 c1906488 c1876ba8 00000000
[ 64.656967] 1f40:
ffffffff c1901f60 c030919c c03091a0 60010013 ffffffff 00000051 00000000
[ 64.665102] 1f60:
ffffe000 c0376aa4 c1a9da37 ffffffff 00000037 3f7231be c1ab20c0 000000cc
[ 64.673238] 1f80:
c1906488 c1906480 ffffffff 00000037 c1ab20c0 c1ab20c0 00000001 c0376e1c
[ 64.681373] 1fa0:
c1ab2118 c1700ea8 ffffffff ffffffff 00000000 c1700754 c17dfa40 ebfffd80
[ 64.689509] 1fc0:
00000000 c17dfa40 3f7733be 00000000 00000000 c1700330 00000051 10c0387d
[ 64.697644] 1fe0:
00000000 8f000000 410fc075 10c5387d 00000000 00000000 00000000 00000000
[ 64.705788] [<
c03bd734>] (call_timer_fn) from [<
c03bd95c>] (expire_timers+0xd8/0x144)
[ 64.713579] [<
c03bd95c>] (expire_timers) from [<
c03bdca4>] (run_timer_softirq+0xe4/0x1dc)
[ 64.721716] [<
c03bdca4>] (run_timer_softirq) from [<
c0302298>] (__do_softirq+0x130/0x3c8)
[ 64.729854] [<
c0302298>] (__do_softirq) from [<
c034c784>] (irq_exit+0xbc/0xd8)
[ 64.737040] [<
c034c784>] (irq_exit) from [<
c039fb50>] (__handle_domain_irq+0x60/0xb4)
[ 64.744833] [<
c039fb50>] (__handle_domain_irq) from [<
c0709ca8>] (gic_handle_irq+0x58/0x9c)
[ 64.753143] [<
c0709ca8>] (gic_handle_irq) from [<
c0301a8c>] (__irq_svc+0x6c/0x90)
[ 64.760583] Exception stack(0xc1901f10 to 0xc1901f58)
[ 64.765605] 1f00:
00000000 000070a0 eb6ac1a0 c031da60
[ 64.773740] 1f20:
ffffe000 c19064ac c19064f0 00000001 00000000 c1906488 c1876ba8 00000000
[ 64.781873] 1f40:
ffffffff c1901f60 c030919c c03091a0 60010013 ffffffff
[ 64.788456] [<
c0301a8c>] (__irq_svc) from [<
c03091a0>] (arch_cpu_idle+0x38/0x3c)
[ 64.795816] [<
c03091a0>] (arch_cpu_idle) from [<
c0376aa4>] (do_idle+0x1bc/0x298)
[ 64.803175] [<
c0376aa4>] (do_idle) from [<
c0376e1c>] (cpu_startup_entry+0x18/0x1c)
[ 64.810707] [<
c0376e1c>] (cpu_startup_entry) from [<
c1700ea8>] (start_kernel+0x480/0x4ac)
[ 64.818839] Code: bad PC value
[ 64.821890] ---[ end trace
e226ed97b1c584cd ]---
[ 64.826482] Kernel panic - not syncing: Fatal exception in interrupt
[ 64.832807] CPU1: stopping
[ 64.835501] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D
5.2.0-rc5-01634-ge3a2773ba9e5 #1246
[ 64.845013] Hardware name: Freescale LS1021A
[ 64.849266] [<
c0312394>] (unwind_backtrace) from [<
c030cc74>] (show_stack+0x10/0x14)
[ 64.856972] [<
c030cc74>] (show_stack) from [<
c0ff4138>] (dump_stack+0xb4/0xc8)
[ 64.864159] [<
c0ff4138>] (dump_stack) from [<
c0310854>] (handle_IPI+0x3bc/0x3dc)
[ 64.871519] [<
c0310854>] (handle_IPI) from [<
c0709ce8>] (gic_handle_irq+0x98/0x9c)
[ 64.879050] [<
c0709ce8>] (gic_handle_irq) from [<
c0301a8c>] (__irq_svc+0x6c/0x90)
[ 64.886489] Exception stack(0xea8cbf60 to 0xea8cbfa8)
[ 64.891514] bf60:
00000000 0000307c eb6c11a0 c031da60 ffffe000 c19064ac c19064f0 00000002
[ 64.899649] bf80:
00000000 c1906488 c1876ba8 00000000 00000000 ea8cbfb0 c030919c c03091a0
[ 64.907780] bfa0:
600d0013 ffffffff
[ 64.911250] [<
c0301a8c>] (__irq_svc) from [<
c03091a0>] (arch_cpu_idle+0x38/0x3c)
[ 64.918609] [<
c03091a0>] (arch_cpu_idle) from [<
c0376aa4>] (do_idle+0x1bc/0x298)
[ 64.925967] [<
c0376aa4>] (do_idle) from [<
c0376e1c>] (cpu_startup_entry+0x18/0x1c)
[ 64.933496] [<
c0376e1c>] (cpu_startup_entry) from [<
803025cc>] (0x803025cc)
[ 64.940422] Rebooting in 3 seconds..
In this case, what happened is that the DSA driver failed to probe at
boot time due to a PHY issue during phylink_connect_phy:
[ 2.245607] fsl-gianfar soc:ethernet@
2d90000 eth2: error -19 setting up slave phy
[ 2.258051] sja1105 spi0.1: failed to create slave for port 0.0
Fixes:
bb77f36ac21d ("net: dsa: sja1105: Add support for the PTP clock")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 25 Jun 2019 23:39:33 +0000 (02:39 +0300)]
net: dsa: sja1105: Build PTP support in main DSA driver
As Arnd Bergmann pointed out in commit
78fe8a28fb96 ("net: dsa: sja1105:
fix ptp link error"), there is no point in having PTP support as a
separate loadable kernel module.
So remove the exported symbols and make sja1105.ko contain PTP support
or not based on CONFIG_NET_DSA_SJA1105_PTP.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Jun 2019 18:00:32 +0000 (11:00 -0700)]
Merge branch 'net-dsa-microchip-Convert-to-regmap'
Marek Vasut says:
====================
net: dsa: microchip: Convert to regmap
This patchset converts KSZ9477 switch driver to regmap.
This was tested with extra patches on KSZ8795. This was also tested
on KSZ9477 on Microchip KSZ9477EVB board, which I now have.
====================
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 25 Jun 2019 23:43:48 +0000 (01:43 +0200)]
net: dsa: microchip: Replace ad-hoc bit manipulation with regmap
Regmap provides bit manipulation functions to set/clear bits, use those
insted of reimplementing them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Tue, 25 Jun 2019 23:43:47 +0000 (01:43 +0200)]
net: dsa: microchip: Factor out regmap config generation into common header
The regmap config tables are rather similar for various generations of
the KSZ8xxx/KSZ9xxx switches. Introduce a macro which allows generating
those tables without duplication. Note that $regalign parameter is not
used right now, but will be used in KSZ87xx series switches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Tue, 25 Jun 2019 23:43:46 +0000 (01:43 +0200)]
net: dsa: microchip: Dispose of ksz_io_ops
Since the driver now uses regmap , get rid of ad-hoc ksz_io_ops
abstraction, which no longer has any meaning. Moreover, since regmap
has it's own locking, get rid of the register access mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Tue, 25 Jun 2019 23:43:45 +0000 (01:43 +0200)]
net: dsa: microchip: Initial SPI regmap support
Add basic SPI regmap support into the driver.
Previous patches unconver that ksz_spi_write() is always ever called
with len = 1, 2 or 4. We can thus drop the if (len > SPI_TX_BUF_LEN)
check and we can also drop the allocation of the txbuf which is part
of the driver data and wastes 256 bytes for no reason. Regmap covers
the whole thing now.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Tue, 25 Jun 2019 23:43:44 +0000 (01:43 +0200)]
net: dsa: microchip: Factor out register access opcode generation
Factor out the code which sends out the register read/write opcodes
to the switch, since the code differs in single bit between read and
write.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Tue, 25 Jun 2019 23:43:43 +0000 (01:43 +0200)]
net: dsa: microchip: Use PORT_CTRL_ADDR() instead of indirect function call
The indirect function call to dev->dev_ops->get_port_addr() is expensive
especially if called for every single register access, and only returns
the value of PORT_CTRL_ADDR() macro. Use PORT_CTRL_ADDR() macro directly
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Tue, 25 Jun 2019 23:43:42 +0000 (01:43 +0200)]
net: dsa: microchip: Move ksz_cfg and ksz_port_cfg to ksz9477.c
These functions are only used by the KSZ9477 code, move them from
the header into that code. Note that these functions will be soon
replaced by regmap equivalents.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Tue, 25 Jun 2019 23:43:41 +0000 (01:43 +0200)]
net: dsa: microchip: Inline ksz_spi.h
The functions in the header file are static, and the header file is
included from single C file, just inline the code into the C file.
The bonus is that it's easier to spot further content to clean up.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Tue, 25 Jun 2019 23:43:40 +0000 (01:43 +0200)]
net: dsa: microchip: Remove ksz_{get,set}()
These functions and callbacks are never used, remove them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Tue, 25 Jun 2019 23:43:39 +0000 (01:43 +0200)]
net: dsa: microchip: Remove ksz_{read,write}24()
These functions and callbacks are never used, remove them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Jun 2019 17:58:32 +0000 (10:58 -0700)]
Merge branch 'net-aquantia-implement-vlan-offloads'
Igor Russkikh says:
====================
net: aquantia: implement vlan offloads
This patchset introduces hardware VLAN offload support and also does some
maintenance: we replace driver version with uts version string, add
documentation file for atlantic driver, and update maintainers
adding Igor as a maintainer.
v3: shuffle doc sections, per Andrew's comments
v2: updates in doc, gpl spdx tag cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Wed, 26 Jun 2019 12:35:49 +0000 (12:35 +0000)]
net: aquantia: implement vlan offload configuration
set_features should update flags and reinit hardware if
vlan offload settings were changed.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Wed, 26 Jun 2019 12:35:46 +0000 (12:35 +0000)]
net: aquantia: vlan offloads logic in datapath
Update datapath by adding logic related to hardware assisted
vlan strip/insert behaviour.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Wed, 26 Jun 2019 12:35:44 +0000 (12:35 +0000)]
net: aquantia: adding fields and device features for vlan offload
Updating features and vlan_features with vlan HW offload.
Added vlan_tag fields to rx/tx ring_buff to track vlan related data.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Wed, 26 Jun 2019 12:35:42 +0000 (12:35 +0000)]
net: aquantia: added vlan offload related macros and functions
Register declaration macros required to work with vlan offload mode.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Wed, 26 Jun 2019 12:35:40 +0000 (12:35 +0000)]
net: aquantia: make all files GPL-2.0-only
It was noticed some files had -or-later, however overall driver has
-only license. Clean this up.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Wed, 26 Jun 2019 12:35:37 +0000 (12:35 +0000)]
maintainers: declare aquantia atlantic driver maintenance
Aquantia is resposible now for all new features and bugfixes.
Reflect that in MAINTAINERS.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Wed, 26 Jun 2019 12:35:35 +0000 (12:35 +0000)]
net: aquantia: add documentation for the atlantic driver
Document contains configuration options description,
details and examples of driver various settings.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Wed, 26 Jun 2019 12:35:33 +0000 (12:35 +0000)]
net: aquantia: replace internal driver version code with uts
As it was discussed some time previously, driver is better to
report kernel version string, as it in a best way identifies
the codebase.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Jun 2019 17:49:06 +0000 (10:49 -0700)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-06-26
This series contains updates to ixgbe and i40e only.
Mauro S. M. Rodrigues update the ixgbe driver to handle transceivers who
comply with SFF-8472 but do not implement the Digital Diagnostic
Monitoring (DOM) interface. Update the driver to check the necessary
bits to see if DOM is implemented before trying to read the additional
256 bytes in the EEPROM for DOM data.
Young Xiao fixes a potential divide by zero issue in ixgbe driver.
Aleksandr fixes i40e to recognize 2.5 and 5.0 GbE link speeds so that it
is not reported as "Unknown bps". Fixes the driver to read the firmware
LLDP agent status during DCB initialization, and to properly log the
LLDP agent status to help with debugging when DCB fails to initialize.
Martyna fixes i40e for the missing supported and advertised link modes
information in ethtool.
Jake fixes a function header comment that was incorrect for a PTP
function in i40e.
Maciej fixes an issue for i40e when a XDP program is loaded the
descriptor count gets reset to the default value, resolve the issue by
making the current descriptor count persistent across resets.
Alice corrects a copyright date which she found to be incorrect.
Piotr adds a log entry when the traffic class 0 is added or deleted, which
was not being logged previously.
Gustavo A. R. Silva updates i40e to use struct_size() where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Jun 2019 17:18:24 +0000 (10:18 -0700)]
Merge branch 's390-qeth-next'
Julian Wiedmann says:
====================
s390/qeth: updates 2019-06-27
please apply another round of qeth updates for net-next.
This completes the conversion of the control path to use dynamically
allocated cmd buffers, along with some fine-tuning for the route
validation fix that recently went into -net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:33 +0000 (17:01 +0200)]
s390/qeth: move cast type selection into fill_header()
The cast type currently gets selected in .ndo_start_xmit, and is then
piped through several layers until it's stored into the HW header.
Push the selection down into qeth_l?_fill_header() to (1) reduce the
number of xmit-wide parameters, and (2) merge the two route validation
checks into just one.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:32 +0000 (17:01 +0200)]
s390/qeth: extract helper for route validation
As follow-up to commit
0cd6783d3c7d ("s390/qeth: check dst entry before use"),
consolidate the dst_check() logic into a single helper and add a wrapper
around the cast type selection.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:31 +0000 (17:01 +0200)]
s390/qeth: consolidate skb RX processing in L3 driver
Use napi_gro_receive() to pass up all types of packets that a L3 device
may receive.
1) For proper L2 packets received by the IQD sniffer, this is the
obvious thing to do.
2) For af_iucv (which doesn't provide a GRO assist), the GRO code will
transparently fall back to netif_receive_skb(). So there's no need to
special-case this traffic in our code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:30 +0000 (17:01 +0200)]
s390/qeth: consolidate pm code
De-duplicate the pm callback implementations from the two sub-drivers,
replacing them with core helpers that delegate to the .set_online and
.set_offline callbacks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:29 +0000 (17:01 +0200)]
s390/qeth: streamline SNMP cmd code
Apply some cleanups to qeth_snmp_command() and its callback:
1. when accessing the user data, use the proper struct instead of
hard-coded offsets. Also copy the request data straight into the
allocated cmd, skipping the extra memdup_user() to a tmp buffer.
2. capping the request length is no longer needed, the same check gets
applied at a base level in qeth_alloc_cmd().
3. clean up some duplicated (and misindented) trace statements.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:28 +0000 (17:01 +0200)]
s390/qeth: remove static cmd buffer infrastructure
Now that all cmds are dynamically allocated, the code for static cmd
buffers can go away entirely. Resulting in a nice reduction of
code/data size & complexity, while removing the risk that
qeth_clear_cmd_buffers() releases cmds that are still in-flight.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:27 +0000 (17:01 +0200)]
s390/qeth: dynamically allocate MPC cmds
The base MPC cmds are the last remaining user of the static cmd buffers.
Port them over to use dynamic allocation, and stop backing the write
channel's cmd buffers with pages.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:26 +0000 (17:01 +0200)]
s390/qeth: dynamically allocate vnicc cmds
The VNICC code is somewhat quirky in that it defers the whole cmd setup
to a common helper qeth_l2_vnicc_request(). Some of the cmd specifics
are then passed in via parameter, while others are simply hard-coded.
Split the whole machinery up into the usual format: one helper that
allocates the cmd & fills in the common fields, while all the cmd
originators take care of their sub-cmd type specific work.
This makes it much easier to calculate the cmd's precise length, and
reduces code complexity.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:25 +0000 (17:01 +0200)]
s390/qeth: dynamically allocate diag cmds
Add a new wrapper that allocates DIAG cmds of the right size, and fills
in the common fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:24 +0000 (17:01 +0200)]
s390/qeth: dynamically allocate various cmds with sub-types
This patch converts the adapter, assist and bridgeport cmd paths to
dynamic allocation. Most of the work is about re-organizing the cmd
headers, calculating the correct cmd length, and filling in the right
value in the sub-cmd's length field.
Since we now also set the correct length for cmds that are not reflected
by a fixed struct (ie SNMP), we can remove the work-around from
qeth_snmp_command().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:23 +0000 (17:01 +0200)]
s390/qeth: clarify parameter for simple assist cmds
For code that uses qeth_send_simple_setassparms_prot(), we currently
can't differentiate whether the cmd should contain (1) no parameter, or
(2) a 4-byte parameter with value 0.
At the moment this doesn't cause any trouble. But when using dynamically
allocated cmds, we need to know whether to allocate & transmit an
additional 4 bytes of zeroes.
So instead of the raw parameter value, pass a parameter pointer
(or NULL) to qeth_send_simple_setassparms_prot().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 27 Jun 2019 15:01:22 +0000 (17:01 +0200)]
s390/qeth: dynamically allocate simple IPA cmds
This patch reduces the usage of the write channel's static cmd buffers,
by dynamically allocating all simple IPA cmds (eg. STARTLAN, SETVMAC).
It also converts the OSN path.
Doing so requires some changes to how we calculate the cmd length.
Currently when building IPA cmds, we're quite generous in how much data
we send down to the device (basically the size of the biggest cmd we
know). This is no real concern at the moment, since the static cmd
buffers are backed with zeroed pages. But for dynamic allocations, the
exact length matters. So this patch also adds the needed length
calculations to each cmd path.
Commands that have multiple subtypes (eg. SETADP) of differing length
will be converted with follow-up patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 27 Jun 2019 13:04:52 +0000 (15:04 +0200)]
net/smc: common release code for non-accepted sockets
There are common steps when releasing an accepted or unaccepted socket.
Move this code into a common routine.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 27 Jun 2019 16:54:35 +0000 (09:54 -0700)]
Merge branch 'net-ipv4-fix-circular-list-infinite-loop'
Florian Westphal says:
====================
net: ipv4: fix circular-list infinite loop
Tariq and Ran reported a regression caused by net-next commit
2638eb8b50cf ("net: ipv4: provide __rcu annotation for ifa_list").
This happens when net.ipv4.conf.$dev.promote_secondaries sysctl is
enabled -- we can arrange for ifa->next to point at ifa, so next
process that tries to walk the list loops forever.
Fix this and extend rtnetlink.sh with a small test case for this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Thu, 27 Jun 2019 12:03:33 +0000 (14:03 +0200)]
selftests: rtnetlink: add small test case with 'promote_secondaries' enabled
This exercises the 'promote_secondaries' code path.
Without previous fix, this triggers infinite loop/soft lockup:
ifconfig process spinning at 100%, never to return.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Thu, 27 Jun 2019 12:03:32 +0000 (14:03 +0200)]
net: ipv4: fix infinite loop on secondary addr promotion
secondary address promotion causes infinite loop -- it arranges
for ifa->ifa_next to point back to itself.
Problem is that 'prev_prom' and 'last_prim' might point at the same entry,
so 'last_sec' pointer must be obtained after prev_prom->next update.
Fixes:
2638eb8b50cf ("net: ipv4: provide __rcu annotation for ifa_list")
Reported-by: Ran Rozenstein <ranro@mellanox.com>
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier [Thu, 27 Jun 2019 08:52:26 +0000 (10:52 +0200)]
net: ethtool: Allow parsing ETHER_FLOW types when using flow_rule
When parsing an ethtool_rx_flow_spec, users can specify an ethernet flow
which could contain matches based on the ethernet header, such as the
MAC address, the VLAN tag or the ethertype.
ETHER_FLOW uses the src and dst ethernet addresses, along with the
ethertype as keys. Matches based on the vlan tag are also possible, but
they are specified using the special FLOW_EXT flag.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Pablo Neira Ayuso <pablo@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 26 Jun 2019 21:09:33 +0000 (14:09 -0700)]
Merge branch 'macb-build-fixes'
Palmer Dabbelt says:
====================
net: macb: Fix compilation on systems without COMMON_CLK, v2
Our patch to add support for the FU540-C000 broke compilation on at
least powerpc allyesconfig, which was found as part of the linux-next
build regression tests. This must have somehow slipped through the
cracks, as the patch has been reverted in linux-next for a while now.
This patch applies on top of the offending commit, which is the only one
I've even tried it on as I'm not sure how this subsystem makes it to
Linus.
This patch set fixes the issue by adding a dependency of COMMON_CLK to
the MACB Kconfig entry, which avoids the build failure by disabling MACB
on systems where it wouldn't compile. All known users of MACB have
COMMON_CLK, so this shouldn't cause any issues. This is a significantly
simpler approach than disabling just the FU540-C000 support.
I've also included a second patch to indicate this is a driver for a
Cadence device that was originally written by an engineer at Atmel. The
only relation is that I stumbled across it when writing the first patch.
Changes since v1 <
20190624061603.1704-1-palmer@sifive.com>:
* Disable MACB on systems without COMMON_CLK, instead of just disabling
the FU540-C000 support on these systems.
* Update the commit message to reflect the driver was written by Atmel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Palmer Dabbelt [Tue, 25 Jun 2019 08:48:28 +0000 (01:48 -0700)]
net: macb: Kconfig: Rename Atmel to Cadence
The help text makes it look like NET_VENDOR_CADENCE enables support for
Atmel devices, when in reality it's a driver written by Atmel that
supports Cadence devices. This may confuse users that have this device
on a non-Atmel SoC.
The fix is just s/Atmel/Cadence/, but I did go and re-wrap the Kconfig
help text as that change caused it to go over 80 characters.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Palmer Dabbelt [Tue, 25 Jun 2019 08:48:27 +0000 (01:48 -0700)]
net: macb: Kconfig: Make MACB depend on COMMON_CLK
commit
c218ad559020 ("macb: Add support for SiFive FU540-C000") added a
dependency on the common clock framework to the macb driver, but didn't
express that dependency in Kconfig. As a result macb now fails to
compile on systems without COMMON_CLK, which specifically causes a build
failure on powerpc allyesconfig.
This patch adds the dependency, which results in the macb driver no
longer being selectable on systems without the common clock framework.
All known systems that have this device already support the common clock
framework, so this should not cause trouble for any uses. Supporting
both the FU540-C000 and systems without COMMON_CLK is quite ugly.
I've build tested this on powerpc allyesconfig and RISC-V defconfig
(which selects MACB), but I have not even booted the resulting kernels.
Fixes:
c218ad559020 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Taht [Sat, 22 Jun 2019 17:07:34 +0000 (10:07 -0700)]
Allow 0.0.0.0/8 as a valid address range
The longstanding prohibition against using 0.0.0.0/8 dates back
to two issues with the early internet.
There was an interoperability problem with BSD 4.2 in 1984, fixed in
BSD 4.3 in 1986. BSD 4.2 has long since been retired.
Secondly, addresses of the form 0.x.y.z were initially defined only as
a source address in an ICMP datagram, indicating "node number x.y.z on
this IPv4 network", by nodes that know their address on their local
network, but do not yet know their network prefix, in RFC0792 (page
19). This usage of 0.x.y.z was later repealed in RFC1122 (section
3.2.2.7), because the original ICMP-based mechanism for learning the
network prefix was unworkable on many networks such as Ethernet (which
have longer addresses that would not fit into the 24 "node number"
bits). Modern networks use reverse ARP (RFC0903) or BOOTP (RFC0951)
or DHCP (RFC2131) to find their full 32-bit address and CIDR netmask
(and other parameters such as default gateways). 0.x.y.z has had
16,777,215 addresses in 0.0.0.0/8 space left unused and reserved for
future use, since 1989.
This patch allows for these 16m new IPv4 addresses to appear within
a box or on the wire. Layer 2 switches don't care.
0.0.0.0/32 is still prohibited, of course.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: John Gilmore <gnu@toad.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 21 Jun 2019 23:27:16 +0000 (16:27 -0700)]
rtnetlink: skip metrics loop for dst_default_metrics
dst_default_metrics has all of the metrics initialized to 0, so nothing
will be added to the skb in rtnetlink_put_metrics. Avoid the loop if
metrics is from dst_default_metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 26 Jun 2019 20:05:42 +0000 (13:05 -0700)]
Merge branch 'skfp-cleanups'
Puranjay Mohan says:
====================
net: fddi: skfp: Use PCI generic definitions instead of private duplicates
This patch series removes the private duplicates of PCI definitions in
favour of generic definitions defined in pci_regs.h.
This driver only uses some of the generic PCI definitons,
which are included from pci_regs.h and thier private versions
are removed from skfbi.h with all other private defines.
The skfbi.h defines PCI_REV_ID and other private defines with different
names, these are renamed to Generic PCI names to make them
compatible with defines in pci_regs.h.
All unused defines are removed from skfbi.h.
Changes in v5:
Removed unused PCI definitions which were left in v4
Changes in v4:
Removed unused PCI definitions which were left in v3
Changes in v3:
Renamed all local PCI definitions to Generic names.
Corrected coding style mistakes.
Changes in v2:
Converted individual patches to a series.
Made sure that individual patches build correctly
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Puranjay Mohan [Fri, 21 Jun 2019 15:40:37 +0000 (21:10 +0530)]
net: fddi: skfp: Remove unused private PCI definitions
Remove unused private PCI definitions from skfbi.h because generic PCI
symbols are already included from pci_regs.h.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Puranjay Mohan [Fri, 21 Jun 2019 15:40:36 +0000 (21:10 +0530)]
net: fddi: skfp: Include generic PCI definitions
Include the uapi/linux/pci_regs.h header file which contains the generic
PCI defines.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Puranjay Mohan [Fri, 21 Jun 2019 15:40:35 +0000 (21:10 +0530)]
net: fddi: skfp: Rename local PCI defines to match generic PCI defines
Rename the PCI_REV_ID and other local defines to Generic PCI define names
in skfbi.h and drvfbi.c to make it compatible with the pci_regs.h.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 26 Jun 2019 17:12:17 +0000 (10:12 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2019-06-26' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/
20190625160432.
533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Wed, 5 Jun 2019 15:40:52 +0000 (10:40 -0500)]
i40e/i40e_virtchnl_pf: Use struct_size() in kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct virtchnl_iwarp_qvlist_info {
...
struct virtchnl_iwarp_qv_info qv_info[1];
};
size = sizeof(struct virtchnl_iwarp_qvlist_info) + (sizeof(struct virtchnl_iwarp_qv_info) * count;
instance = kzalloc(size, GFP_KERNEL);
and
struct virtchnl_vf_resource {
...
struct virtchnl_vsi_resource vsi_res[1];
};
size = sizeof(struct virtchnl_vf_resource) + sizeof(struct virtchnl_vsi_resource) * count;
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, qv_info, count), GFP_KERNEL);
and
instance = kzalloc(struct_size(instance, vsi_res, count), GFP_KERNEL);
Notice that, in the first case above, variable size is not necessary, hence it
is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Tue, 28 May 2019 17:59:21 +0000 (10:59 -0700)]
i40e: update copyright string
It was found that the string that prints our copyright was
not up to date. Updating to reflect our copyright.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maciej Fijalkowski [Tue, 28 May 2019 17:59:20 +0000 (10:59 -0700)]
i40e: Fix descriptor count manipulation
Changing descriptor count via 'ethtool -G' is not persistent across resets.
When PF reset occurs, we roll back to the default value of vsi->num_desc,
which is used then in i40e_alloc_rings to set descriptor count. XDP does a
PF reset so when user has changed the descriptor count and load XDP
program, the default count will be back there.
To fix this:
* introduce new VSI members - num_tx_desc and num_rx_desc in favour of
num_desc
* set them in i40e_set_ringparam to user's values
* set them to default values in i40e_set_num_rings_in_vsi only when they
don't have previous values
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aleksandr Loktionov [Tue, 28 May 2019 17:59:19 +0000 (10:59 -0700)]
i40e: missing priorities for any QoS traffic
This patch fixes reading f/w LLDP agent status at DCB init time.
It's done by removing direct NVM reading in i40e_update_dcb_config()
and checking whether f/w LLDP agent is disabled via
I40E_FLAG_DISABLE_FW_LLDP flag in i40e_init_pf_dcb(). The function
i40e_update_dcb_config() in i40e_main.c is a temporary solution which
will be later renamed to i40e_init_dcb() in the i40e_dcb module. Also
logging was extended to make visible if f/w LLDP agent is running or not
and always log a message when DCB was not initialized. Without this
patch for new f/w versions f/w LLDP agent status was always read
from NVM as disabled and DCB initialization failed without
clear reason in logs.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Piotr Kwapulinski [Tue, 28 May 2019 17:59:18 +0000 (10:59 -0700)]
i40e: Add log entry while creating or deleting TC0
Generate log entry when TC0 is created or deleted.
Log entry is generated during main VSI setup.
Before there was no log info about adding or deleting TC0.
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 28 May 2019 17:59:17 +0000 (10:59 -0700)]
i40e: fix incorrect function documentation comment
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Martyna Szapar [Tue, 28 May 2019 17:59:16 +0000 (10:59 -0700)]
i40e: Fix for missing "link modes" info in ethtool
Fix for missing "Supported link modes" and "Advertised link modes"
info in ethtool after changed speed on X722 devices with BASE-T PHY
with FW API version >= 1.7.
The same FW API version on X710 and X722 does not mean the same
feature set so the change was needed as mac type of the device
should also be checked instead of FW API version only.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aleksandr Loktionov [Tue, 28 May 2019 17:59:15 +0000 (10:59 -0700)]
i40e: fix 'Unknown bps' in dmesg for 2.5Gb/5Gb speeds
This patch fixes 'NIC Link is Up, Unknown bps' message in dmesg
for 2.5Gb/5Gb speeds. This problem is fixed by adding constants
for VIRTCHNL_LINK_SPEED_2_5GB and VIRTCHNL_LINK_SPEED_5GB cases
in the i40e_virtchnl_link_speed() function.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Young Xiao [Tue, 28 May 2019 11:58:02 +0000 (19:58 +0800)]
ixgbevf: fix possible divide by zero in ixgbevf_update_itr
The next call to ixgbevf_update_itr will continue to dynamically
update ITR.
Copy from commit
bdbeefe8ea8c ("ixgbe: fix possible divide by zero in
ixgbe_update_itr")
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mauro S. M. Rodrigues [Thu, 23 May 2019 19:11:12 +0000 (16:11 -0300)]
ixgbe: Check DDM existence in transceiver before access
Some transceivers may comply with SFF-8472 but not implement the Digital
Diagnostic Monitoring (DDM) interface described in it. The existence of
such area is specified by bit 6 of byte 92, set to 1 if implemented.
Currently, due to not checking this bit ixgbe fails trying to read SFP
module's eeprom with the follow message:
ethtool -m enP51p1s0f0
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it was assumed
to exist the DDM data.
This issue was noticed using a Mellanox Passive DAC PN 01FT738. The eeprom
data was confirmed by Mellanox as correct and present in other Passive
DACs in from other manufacturers.
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jon Hunter [Wed, 26 Jun 2019 10:23:22 +0000 (11:23 +0100)]
net: stmmac: Fix crash observed if PHY does not support EEE
If the PHY does not support EEE mode, then a crash is observed when the
ethernet interface is enabled. The crash occurs, because if the PHY does
not support EEE, then although the EEE timer is never configured, it is
still marked as enabled and so the stmmac ethernet driver is still
trying to update the timer by calling mod_timer(). This triggers a BUG()
in the mod_timer() because we are trying to update a timer when there is
no callback function set because timer_setup() was never called for this
timer.
The problem is caused because we return true from the function
stmmac_eee_init(), marking the EEE timer as enabled, even when we have
not configured the EEE timer. Fix this by ensuring that we return false
if the PHY does not support EEE and hence, 'eee_active' is not set.
Fixes:
74371272f97f ("net: stmmac: Convert to phylink and remove phylib logic")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Hunter [Wed, 26 Jun 2019 10:23:21 +0000 (11:23 +0100)]
net: stmmac: Fix possible deadlock when disabling EEE support
When stmmac_eee_init() is called to disable EEE support, then the timer
for EEE support is stopped and we return from the function. Prior to
stopping the timer, a mutex was acquired but in this case it is never
released and so could cause a deadlock. Fix this by releasing the mutex
prior to returning from stmmax_eee_init() when stopping the EEE timer.
Fixes:
74371272f97f ("net: stmmac: Convert to phylink and remove phylib logic")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 26 Jun 2019 10:05:28 +0000 (03:05 -0700)]
ipv6: fix suspicious RCU usage in rt6_dump_route()
syzbot reminded us that rt6_nh_dump_exceptions() needs to be called
with rcu_read_lock()
net/ipv6/route.c:1593 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by syz-executor609/8966:
#0:
00000000b7dbe288 (rtnl_mutex){+.+.}, at: netlink_dump+0xe7/0xfb0 net/netlink/af_netlink.c:2199
#1:
00000000f2d87c21 (&(&tb->tb6_lock)->rlock){+...}, at: spin_lock_bh include/linux/spinlock.h:343 [inline]
#1:
00000000f2d87c21 (&(&tb->tb6_lock)->rlock){+...}, at: fib6_dump_table.isra.0+0x37e/0x570 net/ipv6/ip6_fib.c:533
stack backtrace:
CPU: 0 PID: 8966 Comm: syz-executor609 Not tainted 5.2.0-rc5+ #43
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
lockdep_rcu_suspicious+0x153/0x15d kernel/locking/lockdep.c:5250
fib6_nh_get_excptn_bucket+0x18e/0x1b0 net/ipv6/route.c:1593
rt6_nh_dump_exceptions+0x45/0x4d0 net/ipv6/route.c:5541
rt6_dump_route+0x904/0xc50 net/ipv6/route.c:5640
fib6_dump_node+0x168/0x280 net/ipv6/ip6_fib.c:467
fib6_walk_continue+0x4a9/0x8e0 net/ipv6/ip6_fib.c:1986
fib6_walk+0x9d/0x100 net/ipv6/ip6_fib.c:2034
fib6_dump_table.isra.0+0x38a/0x570 net/ipv6/ip6_fib.c:534
inet6_dump_fib+0x93c/0xb00 net/ipv6/ip6_fib.c:624
rtnl_dump_all+0x295/0x490 net/core/rtnetlink.c:3445
netlink_dump+0x558/0xfb0 net/netlink/af_netlink.c:2244
__netlink_dump_start+0x5b1/0x7d0 net/netlink/af_netlink.c:2352
netlink_dump_start include/linux/netlink.h:226 [inline]
rtnetlink_rcv_msg+0x73d/0xb00 net/core/rtnetlink.c:5182
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5237
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0x531/0x710 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x8ae/0xd70 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:646 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:665
sock_write_iter+0x27c/0x3e0 net/socket.c:994
call_write_iter include/linux/fs.h:1872 [inline]
new_sync_write+0x4d3/0x770 fs/read_write.c:483
__vfs_write+0xe1/0x110 fs/read_write.c:496
vfs_write+0x20c/0x580 fs/read_write.c:558
ksys_write+0x14f/0x290 fs/read_write.c:611
__do_sys_write fs/read_write.c:623 [inline]
__se_sys_write fs/read_write.c:620 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:620
do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x4401b9
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007ffc8e134978 EFLAGS:
00000246 ORIG_RAX:
0000000000000001
RAX:
ffffffffffffffda RBX:
00000000004002c8 RCX:
00000000004401b9
RDX:
000000000000001c RSI:
0000000020000000 RDI: 00
Fixes:
1e47b4837f3b ("ipv6: Dump route exceptions if requested")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 26 Jun 2019 10:04:50 +0000 (03:04 -0700)]
ipv4: fix suspicious RCU usage in fib_dump_info_fnhe()
sysbot reported that we lack appropriate rcu_read_lock()
protection in fib_dump_info_fnhe()
net/ipv4/route.c:2875 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by syz-executor609/8966:
#0:
00000000b7dbe288 (rtnl_mutex){+.+.}, at: netlink_dump+0xe7/0xfb0 net/netlink/af_netlink.c:2199
stack backtrace:
CPU: 0 PID: 8966 Comm: syz-executor609 Not tainted 5.2.0-rc5+ #43
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
lockdep_rcu_suspicious+0x153/0x15d kernel/locking/lockdep.c:5250
fib_dump_info_fnhe+0x9d9/0x1080 net/ipv4/route.c:2875
fn_trie_dump_leaf net/ipv4/fib_trie.c:2141 [inline]
fib_table_dump+0x64a/0xd00 net/ipv4/fib_trie.c:2175
inet_dump_fib+0x83c/0xa90 net/ipv4/fib_frontend.c:1004
rtnl_dump_all+0x295/0x490 net/core/rtnetlink.c:3445
netlink_dump+0x558/0xfb0 net/netlink/af_netlink.c:2244
__netlink_dump_start+0x5b1/0x7d0 net/netlink/af_netlink.c:2352
netlink_dump_start include/linux/netlink.h:226 [inline]
rtnetlink_rcv_msg+0x73d/0xb00 net/core/rtnetlink.c:5182
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5237
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0x531/0x710 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x8ae/0xd70 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:646 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:665
sock_write_iter+0x27c/0x3e0 net/socket.c:994
call_write_iter include/linux/fs.h:1872 [inline]
new_sync_write+0x4d3/0x770 fs/read_write.c:483
__vfs_write+0xe1/0x110 fs/read_write.c:496
vfs_write+0x20c/0x580 fs/read_write.c:558
ksys_write+0x14f/0x290 fs/read_write.c:611
__do_sys_write fs/read_write.c:623 [inline]
__se_sys_write fs/read_write.c:620 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:620
do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x4401b9
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007ffc8e134978 EFLAGS:
00000246 ORIG_RAX:
0000000000000001
RAX:
ffffffffffffffda RBX:
00000000004002c8 RCX:
00000000004401b9
RDX:
000000000000001c RSI:
0000000020000000 RDI:
0000000000000003
RBP:
00000000006ca018 R08:
00000000004002c8 R09:
00000000004002c8
R10:
0000000000000010 R11:
0000000000000246 R12:
0000000000401a40
R13:
0000000000401ad0 R14:
0000000000000000 R15:
0000000000000000
Fixes:
ee28906fd7a1 ("ipv4: Dump route exceptions if requested")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 25 Jun 2019 16:59:56 +0000 (09:59 -0700)]
Revert "net: ena: ethtool: add extra properties retrieval via get_priv_flags"
This reverts commit
315c28d2b714 ("net: ena: ethtool: add extra properties retrieval via get_priv_flags").
As discussed at netconf and on the mailing list we can't allow
for the the abuse of private flags for exposing arbitrary device
labels.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 26 Jun 2019 15:59:15 +0000 (11:59 -0400)]
Merge branch 'net-hns3-some-code-optimizations-bugfixes'
Huazhong Tan says:
====================
net: hns3: some code optimizations & bugfixes
This patch-set includes code optimizations and bugfixes for
the HNS3 ethernet controller driver.
[patch 1/11] fixes a selftest issue when doing autoneg.
[patch 2/11 - 3-11] adds two code optimizations about VLAN issue.
[patch 4/11] restores the MAC autoneg state after reset.
[patch 5/11 - 8/11] adds some code optimizations and bugfixes about
HW errors handling.
[patch 9/11 - 11/11] fixes some issues related to driver loading and
unloading.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Thu, 20 Jun 2019 08:52:45 +0000 (16:52 +0800)]
net: hns3: add exception handling when enable NIC HW error interrupts
If we failed to enable NIC HW error interrupts during client
initialization in some cases, we should do exception handling to clear
flags and free the resources.
Fixes:
00ea6e5fda9d ("net: hns3: delay and separate enabling of NIC and ROCE HW errors")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 20 Jun 2019 08:52:44 +0000 (16:52 +0800)]
net: hns3: fixes wrong place enabling ROCE HW error when loading
The ROCE HW errors should only be enabled when initializing ROCE's
client, the current code enable it no matter initializing NIC or
ROCE client.
So this patch fixes it.
Fixes:
00ea6e5fda9d ("net: hns3: delay and separate enabling of NIC and ROCE HW errors")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 20 Jun 2019 08:52:43 +0000 (16:52 +0800)]
net: hns3: fix race conditions between reset and module loading & unloading
When loading or unloading module, it should wait for the reset task
done before it un-initializes the client, otherwise the reset task
may cause a NULL pointer reference.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Thu, 20 Jun 2019 08:52:42 +0000 (16:52 +0800)]
net: hns3: add check to number of buffer descriptors
This patch adds check to number of bds before we allocate memory for
them. If we get an invalid bd num in some cases, it will cause a memory
overflow.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Thu, 20 Jun 2019 08:52:41 +0000 (16:52 +0800)]
net: hns3: remove override_pci_need_reset
We add override_pci_need_reset to prevent redundant and unwanted PF
resets if a RAS error occurs in commit
69b51bbb03f7 ("net: hns3: fix
to stop multiple HNS reset due to the AER changes").
Now in HNS3 driver, we use hw_err_reset_req to record reset level that
we need to recover from a RAS error. This variable cans solve above
issue as override_pci_need_reset, so this patch removes
override_pci_need_reset.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Thu, 20 Jun 2019 08:52:40 +0000 (16:52 +0800)]
net: hns3: modify handling of out of memory in hclge_err.c
Users should be informed if HNS driver failed to allocate memory for
descriptor when handling hw errors. This patch solve above issues.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Thu, 20 Jun 2019 08:52:39 +0000 (16:52 +0800)]
net: hns3: code optimizaition of hclge_handle_hw_ras_error()
This patch optimizes hclge_handle_hw_ras_error() to make the code logic
clearer.
1. If there was no NIC or Roce RAS when we read
HCLGE_RAS_PF_OTHER_INT_STS_REG, we return directly.
2. Because NIC and Roce RAS may occurs at the same time, so we should
check value of revision at first before we handle Roce RAS instead
of only checking it in branch of no NIC RAS is detected.
3. Check HCLGE_STATE_RST_HANDLING each time before we want to return
PCI_ERS_RESULT_NEED_RESET.
4. Remove checking of HCLGE_RAS_REG_NFE_MASK and
HCLGE_RAS_REG_ROCEE_ERR_MASK because if hw_err_reset_req is not
zero, it proves that we have set it in handling of NIC or Roce RAS.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 20 Jun 2019 08:52:38 +0000 (16:52 +0800)]
net: hns3: restore the MAC autoneg state after reset
When doing global reset, the MAC autoneg state of fibre
port is set to default, which may cause user configuration
lost. This patch fixes it by restore the MAC autoneg state
after reset.
Fixes:
22f48e24a23d ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 20 Jun 2019 08:52:37 +0000 (16:52 +0800)]
net: hns3: sync VLAN filter entries when kill VLAN ID failed
When HW is resetting, firmware is unable to handle commands
from driver. So if remove VLAN device from stack at this time,
it will fail to remove the VLAN ID from HW VLAN filter, then
the VLAN filter status is unsynced with stack.
This patch fixes it by recording the VLAN ID delete failed,
and removes them again when reset complete.
Fixes:
44e626f720c3 ("net: hns3: fix VLAN offload handle for VLAN inserted by port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 20 Jun 2019 08:52:36 +0000 (16:52 +0800)]
net: hns3: remove VF VLAN filter entry inexistent warning print
For VF VLAN filter is disabled when VF VLAN table is full, then the
new VLAN ID won't be added into VF VLAN table, it will always print
fail log when remove these VLAN IDs. If user has added too many
VLANs, it will cause massive verbose print logs.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 20 Jun 2019 08:52:35 +0000 (16:52 +0800)]
net: hns3: fix selftest fail issue for fibre port with autoneg on
When doing selftest for fibre port with autoneg on, the MAC speed
may be incorrect, which may cause the selftest failed. This patch
fixes it by halting autoneg during the selftest.
Fixes:
22f48e24a23d ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Mashak [Tue, 25 Jun 2019 18:18:52 +0000 (14:18 -0400)]
tc-testing: add ingress qdisc tests
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Tue, 25 Jun 2019 17:37:00 +0000 (19:37 +0200)]
tipc: rename function msg_get_wrapped() to msg_inner_hdr()
We rename the inline function msg_get_wrapped() to the more
comprehensible msg_inner_hdr().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Tue, 25 Jun 2019 16:08:13 +0000 (18:08 +0200)]
tipc: eliminate unnecessary skb expansion during retransmission
We increase the allocated headroom for the buffer copies to be
retransmitted. This eliminates the need for the lower stack levels
(UDP/IP/L2) to expand the headroom in order to add their own headers.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Tue, 25 Jun 2019 15:36:43 +0000 (17:36 +0200)]
tipc: simplify stale link failure criteria
In commit
a4dc70d46cf1 ("tipc: extend link reset criteria for stale
packet retransmission") we made link retransmission failure events
dependent on the link tolerance, and not only of the number of failed
retransmission attempts, as we did earlier. This works well. However,
keeping the original, additional criteria of 99 failed retransmissions
is now redundant, and may in some cases lead to failure detection
times in the order of minutes instead of the expected 1.5 sec link
tolerance value.
We now remove this criteria altogether.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates [Tue, 25 Jun 2019 01:00:27 +0000 (21:00 -0400)]
tc-testing: Restore original behaviour for namespaces in tdc
This patch restores the original behaviour for tdc prior to the
introduction of the plugin system, where the network namespace
functionality was split from the main script.
It introduces the concept of required plugins for testcases,
and will automatically load any plugin that isn't already
enabled when said plugin is required by even one testcase.
Additionally, the -n option for the nsPlugin is deprecated
so the default action is to make use of the namespaces.
Instead, we introduce -N to not use them, but still create
the veth pair.
buildebpfPlugin's -B option is also deprecated.
If a test cases requires the features of a specific plugin
in order to pass, it should instead include a new key/value
pair describing plugin interactions:
"plugins": {
"requires": "buildebpfPlugin"
},
A test case can have more than one required plugin: a list
can be inserted as the value for 'requires'.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Acked-by: Davide Caratti <dcaratti@redhat.com>
Tested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 25 Jun 2019 19:42:12 +0000 (12:42 -0700)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patches contains Netfilter updates for net-next:
1) .br_defrag indirection depends on CONFIG_NF_DEFRAG_IPV6, from wenxu.
2) Remove unnecessary memset() in ipset, from Florent Fourcot.
3) Merge control plane addition and deletion in ipset, also from Florent.
4) A few missing check for nla_parse() in ipset, from Aditya Pakki
and Jozsef Kadlecsik.
5) Incorrect cleanup in error path of xt_set version 3, from Jozsef.
6) Memory accounting problems when resizing in ipset, from Stefano Brivio.
7) Jozsef updates his email to @netfilter.org, this batch comes with a
conflict resolution with recent SPDX header updates.
8) Add to create custom conntrack expectations via nftables, from
Stephane Veyret.
9) A lookup optimization for conntrack, from Florian Westphal.
10) Check for supported flags in xt_owner.
11) Support for pernet sysctl in br_netfilter, patches
from Christian Brauner.
12) Patches to move common synproxy infrastructure to nf_synproxy.c,
to prepare the synproxy support for nf_tables, patches from
Fernando Fernandez Mancera.
13) Support to restore expiration time in set element, from Laura Garcia.
14) Fix recent rewrite of netfilter IPv6 to avoid indirections
when CONFIG_IPV6 is unset, from Arnd Bergmann.
15) Always reset vlan tag on skbuff fraglist when refragmenting in
bridge conntrack, from wenxu.
16) Support to match IPv4 options in nf_tables, from Stephen Suryaputra.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ard Biesheuvel [Mon, 17 Jun 2019 08:43:38 +0000 (10:43 +0200)]
airo: switch to skcipher interface
The AIRO driver applies a ctr(aes) on a buffer of considerable size
(2400 bytes), and instead of invoking the crypto API to handle this
in its entirety, it open codes the counter manipulation and invokes
the AES block cipher directly.
Let's fix this, by switching to the sync skcipher API instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stanislaw Gruszka [Sat, 15 Jun 2019 10:01:00 +0000 (12:01 +0200)]
rt2800: do not enable watchdog by default
Make watchdog disabled by default and add module parameter to enable it.
User will have to create file in /etc/modprobe.d/ with
options rt2800lib watchdog=1
to enable the watchdog or load "rt2800lib watchdog=1" module manually
before loading rt2800{soc,pci,usb} module.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stanislaw Gruszka [Sat, 15 Jun 2019 10:00:59 +0000 (12:00 +0200)]
rt2x00: add restart hw
Add ieee80211_restart_hw() to watchdog and debugfs file for testing
if restart works as expected.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stanislaw Gruszka [Sat, 15 Jun 2019 10:00:58 +0000 (12:00 +0200)]
rt2800: do not nullify initialization vector data
If we restart hw we should keep existing IV (initialization vector)
otherwise HW encryption will be broken after restart.
Also fix some coding style issues on the way.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>