OSDN Git Service
Amit Cohen [Thu, 23 Sep 2021 12:36:53 +0000 (15:36 +0300)]
mlxsw: reg: Add support for rtdp_ipip6_pack()
The RTDP register is used for configuring the tunnel decapsulation
properties of NVE and IP-in-IP.
Linux tunnels verify packets before decapsulation based on the packet's
source IP, which must match tunnel remote IP.
RTDP is used to configure decapsulation so that it filters out packets that
are not IPv6 or have the wrong source IP or wrong GRE key.
For IP-in-IP entry, source IPv4 is saved as part of this register and
source IPv6 is saved by RIPS register and RTDP saves pointer to it.
Create common function for configuring both IPv4 and IPv6 and add
dedicated functions for each protocol.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Thu, 23 Sep 2021 12:36:52 +0000 (15:36 +0300)]
mlxsw: reg: Add Router IP version Six Register
The RIPS register is used to store IPv6 addresses for use by the NVE and
IP-in-IP.
For IPv6 underlay support, RATR register needs to hold a pointer to the
remote IPv6 address for encapsulation and RTDP register needs to hold a
pointer to the local IPv6 address for decapsulation check.
Add the required register for saving IPv6 addresses.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Thu, 23 Sep 2021 12:36:51 +0000 (15:36 +0300)]
mlxsw: Take tunnel's type into account when searching underlay device
The function __mlxsw_sp_ipip_netdev_ul_dev_get() returns the underlay
device that corresponds to the overlay device that it gets.
Currently, this function assumes that the tunnel is IPv4 GRE, because it
is the only one that is supported by mlxsw driver.
This assumption will no longer be correct when IPv6 GRE support is added,
resulting in wrong underlay device being returned.
Instead, check 'ol_dev->type' and return the underlay device accordingly.
Move the function to spectrum_ipip.c because spectrum_router.c should not
be aware to tunnel type.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Thu, 23 Sep 2021 12:36:50 +0000 (15:36 +0300)]
mlxsw: spectrum_ipip: Create common function for mlxsw_sp_ipip_ol_netdev_change_gre()
The function mlxsw_sp_ipip_ol_netdev_change_gre4() contains code that
can be shared between IPv4 and IPv6.
The only difference is the way that arguments are taken from tunnel
parameters, which are different between IPv4 and IPv6.
For that, add structure 'mlxsw_sp_ipip_parms' to hold all the required
parameters for the function and save it as part of
'struct mlxsw_sp_ipip_entry' instead of the existing structure that is
not shared between IPv4 and IPv6. Add new operation as part of
'mlxsw_sp_ipip_ops' to initialize the new structure.
Then mlxsw_sp_ipip_ol_netdev_change_gre{4,6}() will prepare the new
structure and both will call the same function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Thu, 23 Sep 2021 12:36:49 +0000 (15:36 +0300)]
mlxsw: spectrum_router: Fix arguments alignment
Suppress the following checkpatch.pl check [1] by adding a variable to
store the IP-in-IP options. Noticed while adding equivalent IPv6 code in
subsequent patches.
[1]
CHECK: Alignment should match open parenthesis
+ mlxsw_reg_ritr_loopback_ipip4_pack(ritr_pl, lb_cf.lb_ipipt,
+
+ MLXSW_REG_RITR_LOOPBACK_IPIP_OPTIONS_GRE_KEY_PRESET,
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Thu, 23 Sep 2021 12:36:48 +0000 (15:36 +0300)]
mlxsw: spectrum_ipip: Pass IP tunnel parameters by reference and as 'const'
Currently, there are several functions that handle 'struct ip_tunnel_parm'
and 'struct __ip6_tnl_parm'.
Change the mentioned functions to get IP tunnel parameters by reference
and as 'const'.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Thu, 23 Sep 2021 12:36:47 +0000 (15:36 +0300)]
mlxsw: spectrum_router: Create common function for fib_entry_type_unset() code
mlxsw_sp_fib4_entry_type_unset() is not specific for IPv4 FIB entry,
move the code to mlxsw_sp_fib_entry_type_unset(), and call this function
from mlxsw_sp_fib4_entry_type_unset() so then it will be used for IPv6
also.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 23 Sep 2021 18:19:49 +0000 (11:19 -0700)]
Merge git://git./linux/kernel/git/netdev/net
net/mptcp/protocol.c
977d293e23b4 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce01 ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 23 Sep 2021 17:30:31 +0000 (10:30 -0700)]
Merge tag 'net-5.15-rc3' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release - regressions:
- dsa: bcm_sf2: fix array overrun in bcm_sf2_num_active_ports()
Previous releases - regressions:
- introduce a shutdown method to mdio device drivers, and make DSA
switch drivers compatible with masters disappearing on shutdown;
preventing infinite reference wait
- fix issues in mdiobus users related to ->shutdown vs ->remove
- virtio-net: fix pages leaking when building skb in big mode
- xen-netback: correct success/error reporting for the
SKB-with-fraglist
- dsa: tear down devlink port regions when tearing down the devlink
port on error
- nexthop: fix division by zero while replacing a resilient group
- hns3: check queue, vf, vlan ids range before using
Previous releases - always broken:
- napi: fix race against netpoll causing NAPI getting stuck
- mlx4_en: ensure link operstate is updated even if link comes up
before netdev registration
- bnxt_en: fix TX timeout when TX ring size is set to the smallest
- enetc: fix illegal access when reading affinity_hint; prevent oops
on sysfs access
- mtk_eth_soc: avoid creating duplicate offload entries
Misc:
- core: correct the sock::sk_lock.owned lockdep annotations"
* tag 'net-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (51 commits)
atlantic: Fix issue in the pm resume flow.
net/mlx4_en: Don't allow aRFS for encapsulated packets
net: mscc: ocelot: fix forwarding from BLOCKING ports remaining enabled
net: ethernet: mtk_eth_soc: avoid creating duplicate offload entries
nfc: st-nci: Add SPI ID matching DT compatible
MAINTAINERS: remove Guvenc Gulce as net/smc maintainer
nexthop: Fix memory leaks in nexthop notification chain listeners
mptcp: ensure tx skbs always have the MPTCP ext
qed: rdma - don't wait for resources under hw error recovery flow
s390/qeth: fix deadlock during failing recovery
s390/qeth: Fix deadlock in remove_discipline
s390/qeth: fix NULL deref in qeth_clear_working_pool_list()
net: dsa: realtek: register the MDIO bus under devres
net: dsa: don't allocate the slave_mii_bus using devres
Doc: networking: Fox a typo in ice.rst
net: dsa: fix dsa_tree_setup error path
net/smc: fix 'workqueue leaked lock' in smc_conn_abort_work
net/smc: add missing error check in smc_clc_prfx_set()
net: hns3: fix a return value error in hclge_get_reset_status()
net: hns3: check vlan id before using it
...
Shakeel Butt [Wed, 22 Sep 2021 22:49:06 +0000 (15:49 -0700)]
memcg: flush lruvec stats in the refault
Prior to the commit
7e1c0d6f5820 ("memcg: switch lruvec stats to rstat")
and the commit
aa48e47e3906 ("memcg: infrastructure to flush memcg
stats"), each lruvec memcg stats can be off by (nr_cgroups * nr_cpus *
32) at worst and for unbounded amount of time. The commit
aa48e47e3906
moved the lruvec stats to rstat infrastructure and the commit
7e1c0d6f5820 bounded the error for all the lruvec stats to (nr_cpus *
32) at worst for at most 2 seconds. More specifically it decoupled the
number of stats and the number of cgroups from the error rate.
However this reduction in error comes with the cost of triggering the
slowpath of stats update more frequently. Previously in the slowpath
the kernel adds the stats up the memcg tree. After
aa48e47e3906, the
kernel triggers the asyn lruvec stats flush through queue_work(). This
causes regression reports from 0day kernel bot [1] as well as from
phoronix test suite [2].
We tried two options to fix the regression:
1) Increase the threshold to trigger the slowpath in lruvec stats
update codepath from 32 to 512.
2) Remove the slowpath from lruvec stats update codepath and instead
flush the stats in the page refault codepath. The assumption is that
the kernel timely flush the stats, so, the update tree would be
small in the refault codepath to not cause the preformance impact.
Following are the results of will-it-scale/page_fault[1|2|3] benchmark
on four settings i.e. (1) 5.15-rc1 as baseline (2) 5.15-rc1 with
aa48e47e3906 and
7e1c0d6f5820 reverted (3) 5.15-rc1 with option-1
(4) 5.15-rc1 with option-2.
test (1) (2) (3) (4)
pg_f1 368563 406277 (10.23%) 399693 (8.44%) 416398 (12.97%)
pg_f2 338399 372133 (9.96%) 369180 (9.09%) 381024 (12.59%)
pg_f3 500853 575399 (14.88%) 570388 (13.88%) 576083 (15.02%)
From the above result, it seems like the option-2 not only solves the
regression but also improves the performance for at least these
benchmarks.
Feng Tang (intel) ran the aim7 benchmark with these two options and
confirms that option-1 reduces the regression but option-2 removes the
regression.
Michael Larabel (phoronix) ran multiple benchmarks with these options
and reported the results at [3] and it shows for most benchmarks
option-2 removes the regression introduced by the commit
aa48e47e3906
("memcg: infrastructure to flush memcg stats").
Based on the experiment results, this patch proposed the option-2 as the
solution to resolve the regression.
Link: https://lore.kernel.org/all/20210726022421.GB21872@xsang-OptiPlex-9020
Link: https://www.phoronix.com/scan.php?page=article&item=linux515-compile-regress
Link: https://openbenchmarking.org/result/2109226-DEBU-LINUX5104
Fixes:
aa48e47e3906 ("memcg: infrastructure to flush memcg stats")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Tested-by: Michael Larabel <Michael@phoronix.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hillf Danton <hdanton@sina.com>,
Cc: Michal Koutný <mkoutny@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sudarsana Reddy Kalluru [Thu, 23 Sep 2021 10:16:05 +0000 (03:16 -0700)]
atlantic: Fix issue in the pm resume flow.
After fixing hibernation resume flow, another usecase was found which
should be explicitly handled - resume when device is in "down" state.
Invoke aq_nic_init jointly with aq_nic_start only if ndev was already
up during suspend/hibernate. We still need to perform nic_deinit() if
caller requests for it, to handle the freeze/resume scenarios.
Fixes:
57f780f1c433 ("atlantic: Fix driver resume flow.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Thu, 23 Sep 2021 06:51:45 +0000 (09:51 +0300)]
net/mlx4_en: Don't allow aRFS for encapsulated packets
Driver doesn't support aRFS for encapsulated packets, return early error
in such a case.
Fixes:
1eb8c695bda9 ("net/mlx4_en: Add accelerated RFS support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 23 Sep 2021 02:03:38 +0000 (19:03 -0700)]
net: mscc: ocelot: fix forwarding from BLOCKING ports remaining enabled
The blamed commit made the fatally incorrect assumption that ports which
aren't in the FORWARDING STP state should not have packets forwarded
towards them, and that is all that needs to be done.
However, that logic alone permits BLOCKING ports to forward to
FORWARDING ports, which of course allows packet storms to occur when
there is an L2 loop.
The ocelot_get_bridge_fwd_mask should not only ask "what can the bridge
do for you", but "what can you do for the bridge". This way, only
FORWARDING ports forward to the other FORWARDING ports from the same
bridging domain, and we are still compatible with the idea of multiple
bridges.
Fixes:
df291e54ccca ("net: ocelot: support multiple bridges")
Suggested-by: Colin Foster <colin.foster@in-advantage.com>
Reported-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Wed, 22 Sep 2021 23:55:48 +0000 (16:55 -0700)]
net: ethernet: mtk_eth_soc: avoid creating duplicate offload entries
Sometimes multiple CLS_REPLACE calls are issued for the same connection.
rhashtable_insert_fast does not check for these duplicates, so multiple
hardware flow entries can be created.
Fix this by checking for an existing entry early
Fixes:
502e84e2382d ("net: ethernet: mtk_eth_soc: add flow offloading support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 22 Sep 2021 18:36:55 +0000 (21:36 +0300)]
net: dsa: sja1105: stop using priv->vlan_aware
Now that the sja1105 driver is finally sane enough again to stop having
a ternary VLAN awareness state, we can remove priv->vlan_aware and query
DSA for the ds->vlan_filtering value (for SJA1105, VLAN filtering is a
global property).
Also drop the paranoid checking that DSA calls ->port_vlan_filtering
multiple times without the VLAN awareness state changing. It doesn't,
the same check is present inside dsa_port_vlan_filtering too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Brown [Wed, 22 Sep 2021 18:30:37 +0000 (19:30 +0100)]
nfc: st-nci: Add SPI ID matching DT compatible
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding the part name used in
the compatible to the list of SPI IDs.
Fixes:
96c8395e2166 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guvenc Gulce [Wed, 22 Sep 2021 17:21:29 +0000 (19:21 +0200)]
MAINTAINERS: remove Guvenc Gulce as net/smc maintainer
Remove myself as net/smc maintainer, as I am
leaving IBM soon and can not maintain net/smc anymore.
Cc: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Sep 2021 11:50:26 +0000 (12:50 +0100)]
Merge branch 'remove-sk-skb-caches'
Paolo Abeni says:
====================
net: remove sk skb caches
Eric noted we would be better off reverting the sk
skb caches.
MPTCP relies on such a feature, so we need a
little refactor of the MPTCP tx path before the mentioned
revert.
The first patch exposes additional TCP helpers. The 2nd patch
changes the MPTCP code to do locally the whole skb allocation
and updating, so it does not rely anymore on core TCP helpers
for that nor the sk skb cache.
As a side effect, we can make the tcp_build_frag helper static.
Finally, we can pull Eric's revert.
RFC -> v1:
- drop driver specific patch - no more needed after helper rename
- rename skb_entail -> tcp_skb_entail (Eric)
- preserve the tcp_build_frag helpwe, just make it static (Eric)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Sep 2021 17:26:43 +0000 (19:26 +0200)]
tcp: remove sk_{tr}x_skb_cache
This reverts the following patches :
- commit
2e05fcae83c4 ("tcp: fix compile error if !CONFIG_SYSCTL")
- commit
4f661542a402 ("tcp: fix zerocopy and notsent_lowat issues")
- commit
472c2e07eef0 ("tcp: add one skb cache for tx")
- commit
8b27dae5a2e8 ("tcp: add one skb cache for rx")
Having a cache of one skb (in each direction) per TCP socket is fragile,
since it can cause a significant increase of memory needs,
and not good enough for high speed flows anyway where more than one skb
is needed.
We want instead to add a generic infrastructure, with more flexible
per-cpu caches, for alien NUMA nodes.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 22 Sep 2021 17:26:42 +0000 (19:26 +0200)]
tcp: make tcp_build_frag() static
After the previous patch the mentioned helper is
used only inside its compilation unit: let's make
it static.
RFC -> v1:
- preserve the tcp_build_frag() helper (Eric)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 22 Sep 2021 17:26:41 +0000 (19:26 +0200)]
mptcp: stop relying on tcp_tx_skb_cache
We want to revert the skb TX cache, but MPTCP is currently
using it unconditionally.
Rework the MPTCP tx code, so that tcp_tx_skb_cache is not
needed anymore: do the whole coalescing check, skb allocation
skb initialization/update inside mptcp_sendmsg_frag(), quite
alike the current TCP code.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 22 Sep 2021 17:26:40 +0000 (19:26 +0200)]
tcp: expose the tcp_mark_push() and tcp_skb_entail() helpers
the tcp_skb_entail() helper is actually skb_entail(), renamed
to provide proper scope.
The two helper will be used by the next patch.
RFC -> v1:
- rename skb_entail to tcp_skb_entail (Eric)
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 22 Sep 2021 11:12:17 +0000 (13:12 +0200)]
mptcp: ensure tx skbs always have the MPTCP ext
Due to signed/unsigned comparison, the expression:
info->size_goal - skb->len > 0
evaluates to true when the size goal is smaller than the
skb size. That results in lack of tx cache refill, so that
the skb allocated by the core TCP code lacks the required
MPTCP skb extensions.
Due to the above, syzbot is able to trigger the following WARN_ON():
WARNING: CPU: 1 PID: 810 at net/mptcp/protocol.c:1366 mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Modules linked in:
CPU: 1 PID: 810 Comm: syz-executor.4 Not tainted 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Code: ff 4c 8b 74 24 50 48 8b 5c 24 58 e9 0f fb ff ff e8 13 44 8b f8 4c 89 e7 45 31 ed e8 98 57 2e fe e9 81 f4 ff ff e8 fe 43 8b f8 <0f> 0b 41 bd ea ff ff ff e9 6f f4 ff ff 4c 89 e7 e8 b9 8e d2 f8 e9
RSP: 0018:
ffffc9000531f6a0 EFLAGS:
00010216
RAX:
000000000000697f RBX:
0000000000000000 RCX:
ffffc90012107000
RDX:
0000000000040000 RSI:
ffffffff88eac9e2 RDI:
0000000000000003
RBP:
ffff888078b15780 R08:
0000000000000000 R09:
0000000000000000
R10:
ffffffff88eac017 R11:
0000000000000000 R12:
ffff88801de0a280
R13:
0000000000006b58 R14:
ffff888066278280 R15:
ffff88803c2fe9c0
FS:
00007fd9f866e700(0000) GS:
ffff8880b9d00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007faebcb2f718 CR3:
00000000267cb000 CR4:
00000000001506e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
__mptcp_push_pending+0x1fb/0x6b0 net/mptcp/protocol.c:1547
mptcp_release_cb+0xfe/0x210 net/mptcp/protocol.c:3003
release_sock+0xb4/0x1b0 net/core/sock.c:3206
sk_stream_wait_memory+0x604/0xed0 net/core/stream.c:145
mptcp_sendmsg+0xc39/0x1bc0 net/mptcp/protocol.c:1749
inet6_sendmsg+0x99/0xe0 net/ipv6/af_inet6.c:643
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:724
sock_write_iter+0x2a0/0x3e0 net/socket.c:1057
call_write_iter include/linux/fs.h:2163 [inline]
new_sync_write+0x40b/0x640 fs/read_write.c:507
vfs_write+0x7cf/0xae0 fs/read_write.c:594
ksys_write+0x1ee/0x250 fs/read_write.c:647
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x4665f9
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007fd9f866e188 EFLAGS:
00000246 ORIG_RAX:
0000000000000001
RAX:
ffffffffffffffda RBX:
000000000056c038 RCX:
00000000004665f9
RDX:
00000000000e7b78 RSI:
0000000020000000 RDI:
0000000000000003
RBP:
00000000004bfcc4 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
000000000056c038
R13:
0000000000a9fb1f R14:
00007fd9f866e300 R15:
0000000000022000
Fix the issue rewriting the relevant expression to avoid
sign-related problems - note: size_goal is always >= 0.
Additionally, ensure that the skb in the tx cache always carries
the relevant extension.
Reported-and-tested-by: syzbot+263a248eec3e875baa7b@syzkaller.appspotmail.com
Fixes:
1094c6fe7280 ("mptcp: fix possible divide by zero")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 22 Sep 2021 15:10:29 +0000 (18:10 +0300)]
net: dsa: sja1105: don't keep a persistent reference to the reset GPIO
The driver only needs the reset GPIO for a very brief period, so instead
of using devres and keeping the descriptor pointer inside priv, just use
that descriptor inside the sja1105_hw_reset function and then let go of
it.
Also use gpiod_get_optional while at it, and error out on real errors
(bad flags etc).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Sep 2021 11:45:07 +0000 (12:45 +0100)]
Merge branch 'ja1105-deps'
Vladimir Oltean says:
====================
Fix circular dependency between sja1105 and tag_sja1105
As discussed here:
https://lore.kernel.org/netdev/
20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocols cannot use symbols exported by switch drivers.
Eliminate the two instances of that from tag_sja1105, and that allows us
to have a working setup with modules again.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 22 Sep 2021 14:37:26 +0000 (17:37 +0300)]
net: dsa: sja1105: break dependency between dsa_port_is_sja1105 and switch driver
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes:
994d2cbb08ca ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 22 Sep 2021 14:37:25 +0000 (17:37 +0300)]
net: dsa: move sja1110_process_meta_tstamp inside the tagging protocol driver
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes:
566b18c8b752 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 22 Sep 2021 13:57:03 +0000 (16:57 +0300)]
net: dsa: sja1105: remove sp->dp
It looks like this field was never used since its introduction in commit
227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through
standalone ports") remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 22 Sep 2021 10:25:40 +0000 (13:25 +0300)]
nexthop: Fix memory leaks in nexthop notification chain listeners
syzkaller discovered memory leaks [1] that can be reduced to the
following commands:
# ip nexthop add id 1 blackhole
# devlink dev reload pci/0000:06:00.0
As part of the reload flow, mlxsw will unregister its netdevs and then
unregister from the nexthop notification chain. Before unregistering
from the notification chain, mlxsw will receive delete notifications for
nexthop objects using netdevs registered by mlxsw or their uppers. mlxsw
will not receive notifications for nexthops using netdevs that are not
dismantled as part of the reload flow. For example, the blackhole
nexthop above that internally uses the loopback netdev as its nexthop
device.
One way to fix this problem is to have listeners flush their nexthop
tables after unregistering from the notification chain. This is
error-prone as evident by this patch and also not symmetric with the
registration path where a listener receives a dump of all the existing
nexthops.
Therefore, fix this problem by replaying delete notifications for the
listener being unregistered. This is symmetric to the registration path
and also consistent with the netdev notification chain.
The above means that unregister_nexthop_notifier(), like
register_nexthop_notifier(), will have to take RTNL in order to iterate
over the existing nexthops and that any callers of the function cannot
hold RTNL. This is true for mlxsw and netdevsim, but not for the VXLAN
driver. To avoid a deadlock, change the latter to unregister its nexthop
listener without holding RTNL, making it symmetric to the registration
path.
[1]
unreferenced object 0xffff88806173d600 (size 512):
comm "syz-executor.0", pid 1290, jiffies
4295583142 (age 143.507s)
hex dump (first 32 bytes):
41 9d 1e 60 80 88 ff ff 08 d6 73 61 80 88 ff ff A..`......sa....
08 d6 73 61 80 88 ff ff 01 00 00 00 00 00 00 00 ..sa............
backtrace:
[<
ffffffff81a6b576>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
[<
ffffffff81a6b576>] slab_post_alloc_hook+0x96/0x490 mm/slab.h:522
[<
ffffffff81a716d3>] slab_alloc_node mm/slub.c:3206 [inline]
[<
ffffffff81a716d3>] slab_alloc mm/slub.c:3214 [inline]
[<
ffffffff81a716d3>] kmem_cache_alloc_trace+0x163/0x370 mm/slub.c:3231
[<
ffffffff82e8681a>] kmalloc include/linux/slab.h:591 [inline]
[<
ffffffff82e8681a>] kzalloc include/linux/slab.h:721 [inline]
[<
ffffffff82e8681a>] mlxsw_sp_nexthop_obj_group_create drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:4918 [inline]
[<
ffffffff82e8681a>] mlxsw_sp_nexthop_obj_new drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5054 [inline]
[<
ffffffff82e8681a>] mlxsw_sp_nexthop_obj_event+0x59a/0x2910 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5239
[<
ffffffff813ef67d>] notifier_call_chain+0xbd/0x210 kernel/notifier.c:83
[<
ffffffff813f0662>] blocking_notifier_call_chain kernel/notifier.c:318 [inline]
[<
ffffffff813f0662>] blocking_notifier_call_chain+0x72/0xa0 kernel/notifier.c:306
[<
ffffffff8384b9c6>] call_nexthop_notifiers+0x156/0x310 net/ipv4/nexthop.c:244
[<
ffffffff83852bd8>] insert_nexthop net/ipv4/nexthop.c:2336 [inline]
[<
ffffffff83852bd8>] nexthop_add net/ipv4/nexthop.c:2644 [inline]
[<
ffffffff83852bd8>] rtm_new_nexthop+0x14e8/0x4d10 net/ipv4/nexthop.c:2913
[<
ffffffff833e9a78>] rtnetlink_rcv_msg+0x448/0xbf0 net/core/rtnetlink.c:5572
[<
ffffffff83608703>] netlink_rcv_skb+0x173/0x480 net/netlink/af_netlink.c:2504
[<
ffffffff833de032>] rtnetlink_rcv+0x22/0x30 net/core/rtnetlink.c:5590
[<
ffffffff836069de>] netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
[<
ffffffff836069de>] netlink_unicast+0x5ae/0x7f0 net/netlink/af_netlink.c:1340
[<
ffffffff83607501>] netlink_sendmsg+0x8e1/0xe30 net/netlink/af_netlink.c:1929
[<
ffffffff832fde84>] sock_sendmsg_nosec net/socket.c:704 [inline]
[<
ffffffff832fde84>] sock_sendmsg net/socket.c:724 [inline]
[<
ffffffff832fde84>] ____sys_sendmsg+0x874/0x9f0 net/socket.c:2409
[<
ffffffff83304a44>] ___sys_sendmsg+0x104/0x170 net/socket.c:2463
[<
ffffffff83304c01>] __sys_sendmsg+0x111/0x1f0 net/socket.c:2492
[<
ffffffff83304d5d>] __do_sys_sendmsg net/socket.c:2501 [inline]
[<
ffffffff83304d5d>] __se_sys_sendmsg net/socket.c:2499 [inline]
[<
ffffffff83304d5d>] __x64_sys_sendmsg+0x7d/0xc0 net/socket.c:2499
Fixes:
2a014b200bbd ("mlxsw: spectrum_router: Add support for nexthop objects")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Wed, 1 Sep 2021 07:09:28 +0000 (09:09 +0200)]
init: Revert accidental changes to print irqs_disabled()
Commit
f8ade8dddb16 ("xsurf100: drop include of lib8390.c") accidentally
changed init/main.c. Revert that part.
Fixes:
f8ade8dddb16 ("xsurf100: drop include of lib8390.c")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Konrad Rzeszutek Wilk [Fri, 17 Sep 2021 16:16:52 +0000 (12:16 -0400)]
MAINTAINERS: Update Xen-[PCI,SWIOTLB,Block] maintainership
Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Juergen, Roger, and Stefano.
Thank you!
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Konrad Rzeszutek Wilk [Fri, 17 Sep 2021 16:16:51 +0000 (12:16 -0400)]
MAINTAINERS: Update SWIOTLB maintainership
Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Christoph Hellwig.
Thank you!
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dinh Nguyen [Wed, 22 Sep 2021 19:30:01 +0000 (14:30 -0500)]
MAINTAINERS: update entry for NIOS2
Ley Foon has left Intel and will no longer be able to maintain NIOS2.
Update the MAINTAINER's entry to Dinh Nguyen.
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 22 Sep 2021 18:58:24 +0000 (11:58 -0700)]
Merge tag 'spi-fix-v5.15-rc1' of git://git./linux/kernel/git/broonie/spi
Pull spi modalias fix from Mark Brown:
"Fix modalias issues
As reported by Russell King the change to use OF style modaliases for
DT enumerated broke at least the spi-nor driver, the patch here
reverts that change to fix the regression.
Sadly this will mean that anything that started loading since the
change to OF modaliases will run into issues, there doesn't seem to be
any approach which doesn't cause some problems and thi seems like the
least bad approach - gory details are in the commit log for the
change.
I'm currently working through the SPI drivers to add ID tables and
missing IDs to tables which should address things from the other end,
this seems more straightforward and robust than any other options"
* tag 'spi-fix-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Revert modalias changes
Linus Torvalds [Wed, 22 Sep 2021 16:21:02 +0000 (09:21 -0700)]
Merge tag 'nfsd-5.15-2' of git://git./linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Critical bug fixes:
- Fix crash in NLM TEST procedure
- NFSv4.1+ backchannel not restored after PATH_DOWN"
* tag 'nfsd-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: back channel stuck in SEQ4_STATUS_CB_PATH_DOWN
NLM: Fix svcxdr_encode_owner()
Linus Torvalds [Wed, 22 Sep 2021 16:16:18 +0000 (09:16 -0700)]
Merge tag 'platform-drivers-x86-v5.15-2' of git://git./linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"The first round of bug-fixes for platform-drivers-x86 for 5.15,
highlights:
- amd-pmc fix for some suspend/resume issues
- intel-hid fix to avoid false-positive SW_TABLET_MODE=1 reporting
- some build error/warning fixes
- various DMI quirk additions"
* tag 'platform-drivers-x86-v5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: gigabyte-wmi: add support for B550I Aorus Pro AX
platform/x86/intel: hid: Add DMI switches allow list
platform/x86: dell: fix DELL_WMI_PRIVACY dependencies & build error
platform/x86: amd-pmc: Increase the response register timeout
platform/x86: touchscreen_dmi: Update info for the Chuwi Hi10 Plus (CWI527) tablet
platform/x86: touchscreen_dmi: Add info for the Chuwi HiBook (CWI514) tablet
lg-laptop: Correctly handle dmi_get_system_info() returning NULL
platform/x86/intel: punit_ipc: Drop wrong use of ACPI_PTR()
Jiri Slaby [Wed, 22 Sep 2021 06:35:58 +0000 (08:35 +0200)]
MAINTAINERS: ARM/VT8500, remove defunct e-mail
linux@prisktech.co.nz is defunct:
4.1.2 <linux@prisktech.co.nz>: Recipient address rejected: Domain not found
Remove it from MAINTAINERS and mark the ARM/VT8500 entry orphan.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paolo Abeni [Wed, 22 Sep 2021 11:12:17 +0000 (13:12 +0200)]
mptcp: ensure tx skbs always have the MPTCP ext
Due to signed/unsigned comparison, the expression:
info->size_goal - skb->len > 0
evaluates to true when the size goal is smaller than the
skb size. That results in lack of tx cache refill, so that
the skb allocated by the core TCP code lacks the required
MPTCP skb extensions.
Due to the above, syzbot is able to trigger the following WARN_ON():
WARNING: CPU: 1 PID: 810 at net/mptcp/protocol.c:1366 mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Modules linked in:
CPU: 1 PID: 810 Comm: syz-executor.4 Not tainted 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Code: ff 4c 8b 74 24 50 48 8b 5c 24 58 e9 0f fb ff ff e8 13 44 8b f8 4c 89 e7 45 31 ed e8 98 57 2e fe e9 81 f4 ff ff e8 fe 43 8b f8 <0f> 0b 41 bd ea ff ff ff e9 6f f4 ff ff 4c 89 e7 e8 b9 8e d2 f8 e9
RSP: 0018:
ffffc9000531f6a0 EFLAGS:
00010216
RAX:
000000000000697f RBX:
0000000000000000 RCX:
ffffc90012107000
RDX:
0000000000040000 RSI:
ffffffff88eac9e2 RDI:
0000000000000003
RBP:
ffff888078b15780 R08:
0000000000000000 R09:
0000000000000000
R10:
ffffffff88eac017 R11:
0000000000000000 R12:
ffff88801de0a280
R13:
0000000000006b58 R14:
ffff888066278280 R15:
ffff88803c2fe9c0
FS:
00007fd9f866e700(0000) GS:
ffff8880b9d00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007faebcb2f718 CR3:
00000000267cb000 CR4:
00000000001506e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
__mptcp_push_pending+0x1fb/0x6b0 net/mptcp/protocol.c:1547
mptcp_release_cb+0xfe/0x210 net/mptcp/protocol.c:3003
release_sock+0xb4/0x1b0 net/core/sock.c:3206
sk_stream_wait_memory+0x604/0xed0 net/core/stream.c:145
mptcp_sendmsg+0xc39/0x1bc0 net/mptcp/protocol.c:1749
inet6_sendmsg+0x99/0xe0 net/ipv6/af_inet6.c:643
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:724
sock_write_iter+0x2a0/0x3e0 net/socket.c:1057
call_write_iter include/linux/fs.h:2163 [inline]
new_sync_write+0x40b/0x640 fs/read_write.c:507
vfs_write+0x7cf/0xae0 fs/read_write.c:594
ksys_write+0x1ee/0x250 fs/read_write.c:647
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x4665f9
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007fd9f866e188 EFLAGS:
00000246 ORIG_RAX:
0000000000000001
RAX:
ffffffffffffffda RBX:
000000000056c038 RCX:
00000000004665f9
RDX:
00000000000e7b78 RSI:
0000000020000000 RDI:
0000000000000003
RBP:
00000000004bfcc4 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
000000000056c038
R13:
0000000000a9fb1f R14:
00007fd9f866e300 R15:
0000000000022000
Fix the issue rewriting the relevant expression to avoid
sign-related problems - note: size_goal is always >= 0.
Additionally, ensure that the skb in the tx cache always carries
the relevant extension.
Reported-and-tested-by: syzbot+263a248eec3e875baa7b@syzkaller.appspotmail.com
Fixes:
1094c6fe7280 ("mptcp: fix possible divide by zero")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shai Malin [Wed, 22 Sep 2021 10:53:26 +0000 (13:53 +0300)]
qed: rdma - don't wait for resources under hw error recovery flow
If the HW device is during recovery, the HW resources will never return,
hence we shouldn't wait for the CID (HW context ID) bitmaps to clear.
This fix speeds up the error recovery flow.
Fixes:
64515dc899df ("qed: Add infrastructure for error detection and recovery")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 22 Sep 2021 13:35:02 +0000 (14:35 +0100)]
Merge branch 'mlxsw-trap-adjacency'
Ido Schimmel says:
====================
mlxsw: Alter trap adjacency entry allocation scheme
In commit
0c3cbbf96def ("mlxsw: Add specific trap for packets routed via
invalid nexthops"), mlxsw started allocating a new adjacency entry
during driver initialization, to trap packets routed via invalid
nexthops.
This behavior was later altered in commit
983db6198f0d ("mlxsw:
spectrum_router: Allocate discard adjacency entry when needed") to only
allocate the entry upon the first route that requires it. The motivation
for the change is explained in the commit message.
The problem with the current behavior is that the entry shows up as a
"leak" in a new BPF resource monitoring tool [1]. This is caused by the
asymmetry of the allocation/free scheme. While the entry is allocated
upon the first route that requires it, it is only freed during
de-initialization of the driver.
Instead, this patchset tracks the number of active nexthop groups and
allocates the adjacency entry upon the creation of the first group. The
entry is freed when the number of active groups reaches zero.
Patch #1 adds the new entry.
Patch #2 converts mlxsw to start using the new entry and removes the old
one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 22 Sep 2021 07:36:42 +0000 (10:36 +0300)]
mlxsw: spectrum_router: Start using new trap adjacency entry
Start using the trap adjacency entry that was added in the previous
patch and remove the existing one which is no longer needed.
Note that the name of the old entry was inaccurate as the entry did not
discard packets, but trapped them.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 22 Sep 2021 07:36:41 +0000 (10:36 +0300)]
mlxsw: spectrum_router: Add trap adjacency entry upon first nexthop group
In commit
0c3cbbf96def ("mlxsw: Add specific trap for packets routed via
invalid nexthops"), mlxsw started allocating a new adjacency entry
during driver initialization, to trap packets routed via invalid
nexthops.
This behavior was later altered in commit
983db6198f0d ("mlxsw:
spectrum_router: Allocate discard adjacency entry when needed") to only
allocate the entry upon the first route that requires it. The motivation
for the change is explained in the commit message.
The problem with the current behavior is that the entry shows up as a
"leak" in a new BPF resource monitoring tool [1]. This is caused by the
asymmetry of the allocation/free scheme. While the entry is allocated
upon the first route that requires it, it is only freed during
de-initialization of the driver.
Instead, track the number of active nexthop groups and allocate the
adjacency entry upon the creation of the first group. Free it when the
number of active groups reaches zero.
The next patch will convert mlxsw to start using the new entry and
remove the old one.
[1] https://github.com/Mellanox/mlxsw/tree/master/Debugging/libbpf-tools/resmon
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Tue, 21 Sep 2021 16:47:36 +0000 (22:17 +0530)]
net: wwan: iosm: fw flashing and cd improvements
1> Function comments moved to .c file.
2> Use literals in return to improve readability.
3> Do error handling check instead of success check.
4> Redundant ret assignment removed.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Wed, 22 Sep 2021 06:17:19 +0000 (14:17 +0800)]
skbuff: pass the result of data ksize to __build_skb_around
Avoid to call ksize again in __build_skb_around by passing
the result of data ksize to __build_skb_around
nginx stress test shows this change can reduce ksize cpu usage,
and give a little performance boost
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Wed, 22 Sep 2021 08:58:03 +0000 (11:58 +0300)]
devlink: Make devlink_register to be void
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 22 Sep 2021 03:02:27 +0000 (20:02 -0700)]
Merge branch 's390-qeth-fixes-2021-09-21'
Julian Wiedmann says:
====================
s390/qeth: fixes 2021-09-21
This brings two fixes for deadlocks when a device is removed while it
has certain types of async work pending. And one additional fix for a
missing NULL check in an error case.
====================
Link: https://lore.kernel.org/r/20210921145217.1584654-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexandra Winter [Tue, 21 Sep 2021 14:52:17 +0000 (16:52 +0200)]
s390/qeth: fix deadlock during failing recovery
Commit
0b9902c1fcc5 ("s390/qeth: fix deadlock during recovery") removed
taking discipline_mutex inside qeth_do_reset(), fixing potential
deadlocks. An error path was missed though, that still takes
discipline_mutex and thus has the original deadlock potential.
Intermittent deadlocks were seen when a qeth channel path is configured
offline, causing a race between qeth_do_reset and ccwgroup_remove.
Call qeth_set_offline() directly in the qeth_do_reset() error case and
then a new variant of ccwgroup_set_offline(), without taking
discipline_mutex.
Fixes:
b41b554c1ee7 ("s390/qeth: fix locking for discipline setup / removal")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexandra Winter [Tue, 21 Sep 2021 14:52:16 +0000 (16:52 +0200)]
s390/qeth: Fix deadlock in remove_discipline
Problem: qeth_close_dev_handler is a worker that tries to acquire
card->discipline_mutex via drv->set_offline() in ccwgroup_set_offline().
Since commit
b41b554c1ee7
("s390/qeth: fix locking for discipline setup / removal")
qeth_remove_discipline() is called under card->discipline_mutex and
cancels the work and waits for it to finish.
STOPLAN reception with reason code IPA_RC_VEPA_TO_VEB_TRANSITION is the
only situation that schedules close_dev_work. In that situation scheduling
qeth recovery will also result in an offline interface, when resetting the
isolation mode fails, if the external switch is still set to VEB.
And since commit
0b9902c1fcc5 ("s390/qeth: fix deadlock during recovery")
qeth recovery does not aquire card->discipline_mutex anymore.
So we accept the longer pathlength of qeth_schedule_recovery in this
error situation and re-use the existing function.
As a side-benefit this changes the hwtrap to behave like during recovery
instead of like during a user-triggered set_offline.
Fixes:
b41b554c1ee7 ("s390/qeth: fix locking for discipline setup / removal")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Julian Wiedmann [Tue, 21 Sep 2021 14:52:15 +0000 (16:52 +0200)]
s390/qeth: fix NULL deref in qeth_clear_working_pool_list()
When qeth_set_online() calls qeth_clear_working_pool_list() to roll
back after an error exit from qeth_hardsetup_card(), we are at risk of
accessing card->qdio.in_q before it was allocated by
qeth_alloc_qdio_queues() via qeth_mpc_initialize().
qeth_clear_working_pool_list() then dereferences NULL, and by writing to
queue->bufs[i].pool_entry scribbles all over the CPU's lowcore.
Resulting in a crash when those lowcore areas are used next (eg. on
the next machine-check interrupt).
Such a scenario would typically happen when the device is first set
online and its queues aren't allocated yet. An early IO error or certain
misconfigs (eg. mismatched transport mode, bad portno) then cause us to
error out from qeth_hardsetup_card() with card->qdio.in_q still being
NULL.
Fix it by checking the pointer for NULL before accessing it.
Note that we also have (rare) paths inside qeth_mpc_initialize() where
a configuration change can cause us to free the existing queues,
expecting that subsequent code will allocate them again. If we then
error out before that re-allocation happens, the same bug occurs.
Fixes:
eff73e16ee11 ("s390/qeth: tolerate pre-filled RX buffer")
Reported-by: Stefan Raspl <raspl@linux.ibm.com>
Root-caused-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mark Brown [Tue, 21 Sep 2021 14:44:06 +0000 (15:44 +0100)]
spi: Revert modalias changes
During the v5.13 cycle we updated the SPI subsystem to generate OF style
modaliases for SPI devices, replacing the old Linux style modalises we
used to generate based on spi_device_id which are the DT style name with
the vendor removed. Unfortunately this means that we start only
reporting OF style modalises and not the old ones and there is nothing
that ensures that drivers list every possible OF compatible string in
their OF ID table. The result is that there are systems which have been
relying on loading modules based on the old style that are now broken,
as found by Russell King with spi-nor on Macchiatobin.
spi-nor is a particularly problematic case for this, it only lists a
single generic DT compatible jedec,spi-nor in the driver but supports a
huge raft of device specific compatibles, with a large set of part
numbers many of which are offered by multiple vendors. Russell's
searches of upstream device trees has turned up examples with vendor
names written in non-standard ways too. To make matters worse up until
8ff16cf77ce3 ("Documentation: devicetree: m25p80: add "nor-jedec"
binding") the generic compatible was not part of the binding so there
are device trees out there written to that binding version which don't
list it all. The sheer number of parts supported together with our
previous approach of ignoring the vendor ID makes robustly fixing this
by adding compatibles to the spi-nor driver seem problematic, the
current DT binding document does not list all the parts supported by the
driver at the minute (further patches will fix this).
I've also investigated supporting both formats of modalias
simultaneously but that doesn't seem possible, especially without
breaking our userspace ABI which is obviously not viable.
Instead revert the relevant changes for now:
e09f2ab8eecc ("spi: update modalias_show after of_device_uevent_modalias support")
3ce6c9e2617e ("spi: add of_device_uevent_modalias support")
This will unfortunately mean that any system which had started having
modules autoload based on the OF compatibles for drivers that list
things there but not in the spi_device_ids will now not have those
modules load which is itself a regression. Since it affects a narrower
time window and the particularly problematic spi-nor driver may be
critical to system boot on smaller systems this seems the best of a
series of bad options. I will start an audit of SPI drivers to identify
and fix cases where things won't autoload using spi_device_id, this is
not great but seems to be the best way forward that anyone has been able
to identify.
Thanks to Russell for both his report and the additional diagnostic and
analysis work he has done here, the detailed research above was his
work.
Fixes:
e09f2ab8eecc ("spi: update modalias_show after of_device_uevent_modalias support")
Fixes:
3ce6c9e2617e ("spi: add of_device_uevent_modalias support")
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: Andreas Schwab <schwab@suse.de>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Linus Torvalds [Tue, 21 Sep 2021 16:36:11 +0000 (09:36 -0700)]
Merge tag 's390-5.15-ebpf-jit-fixes' of git://git./linux/kernel/git/s390/linux
Pull s390 eBPF fixes from Vasily Gorbik:
"Johan Almbladh has implemented a number of new testcases for eBPF [1],
which uncovered three miscompilation issues in the s390 eBPF JIT"
Link: https://lore.kernel.org/bpf/20210902185229.1840281-1-johan.almbladh@anyfinetworks.com/
* tag 's390-5.15-ebpf-jit-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/bpf: Fix optimizing out zero-extensions
s390/bpf: Fix 64-bit subtraction of the -0x80000000 constant
s390/bpf: Fix branch shortening during codegen pass
Linus Torvalds [Mon, 20 Sep 2021 17:26:21 +0000 (10:26 -0700)]
qnx4: work around gcc false positive warning bug
In commit
b7213ffa0e58 ("qnx4: avoid stringop-overread errors") I tried
to teach gcc about how the directory entry structure can be two
different things depending on a status flag. It made the code clearer,
and it seemed to make gcc happy.
However, Arnd points to a gcc bug, where despite using two different
members of a union, gcc then gets confused, and uses the size of one of
the members to decide if a string overrun happens. And not necessarily
the rigth one.
End result: with some configurations, gcc-11 will still complain about
the source buffer size being overread:
fs/qnx4/dir.c: In function 'qnx4_readdir':
fs/qnx4/dir.c:76:32: error: 'strnlen' specified bound [16, 48] exceeds source size 1 [-Werror=stringop-overread]
76 | size = strnlen(name, size);
| ^~~~~~~~~~~~~~~~~~~
fs/qnx4/dir.c:26:22: note: source object declared here
26 | char de_name;
| ^~~~~~~
because gcc will get confused about which union member entry is actually
getting accessed, even when the source code is very clear about it. Gcc
internally will have combined two "redundant" pointers (pointing to
different union elements that are at the same offset), and takes the
size checking from one or the other - not necessarily the right one.
This is clearly a gcc bug, but we can work around it fairly easily. The
biggest thing here is the big honking comment about why we do what we
do.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578#c6
Reported-and-tested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tobias Jakobi [Tue, 21 Sep 2021 10:07:02 +0000 (12:07 +0200)]
platform/x86: gigabyte-wmi: add support for B550I Aorus Pro AX
Tested with a AMD Ryzen 7 5800X.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Thomas Weißschuh <thomas@weissschuh.net>
Link: https://lore.kernel.org/r/20210921100702.3838-1-tjakobi@math.uni-bielefeld.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
José Expósito [Mon, 20 Sep 2021 16:03:12 +0000 (18:03 +0200)]
platform/x86/intel: hid: Add DMI switches allow list
Some devices, even non convertible ones, can send incorrect
SW_TABLET_MODE reports.
Add an allow list and accept such reports only from devices in it.
Bug reported for Dell XPS 17 9710 on:
https://gitlab.freedesktop.org/libinput/libinput/-/issues/662
Reported-by: Tobias Gurtzick <magic@wizardtales.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Tobias Gurtzick <magic@wizardtales.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20210920160312.9787-1-jose.exposito89@gmail.com
[hdegoede@redhat.com: Check dmi_switches_auto_add_allow_list only once]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Randy Dunlap [Sat, 18 Sep 2021 04:48:29 +0000 (21:48 -0700)]
platform/x86: dell: fix DELL_WMI_PRIVACY dependencies & build error
When DELL_WMI=y, DELL_WMI_PRIVACY=y, and LEDS_TRIGGER_AUDIO=m, there
is a linker error since the LEDS trigger code is built as a loadable
module. This happens because DELL_WMI_PRIVACY is a bool that depends
on a tristate (LEDS_TRIGGER_AUDIO=m), which can be dangerous.
ld: drivers/platform/x86/dell/dell-wmi-privacy.o: in function `dell_privacy_wmi_probe':
dell-wmi-privacy.c:(.text+0x3df): undefined reference to `ledtrig_audio_get'
Fixes:
8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Perry Yuan <Perry.Yuan@dell.com>
Cc: Dell.Client.Kernel@dell.com
Cc: platform-driver-x86@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <mgross@linux.intel.com>
Link: https://lore.kernel.org/r/20210918044829.19222-1-rdunlap@infradead.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
David S. Miller [Tue, 21 Sep 2021 12:52:16 +0000 (13:52 +0100)]
Merge branch 'dsa-devres'
Vladimir Oltean says:
====================
Fix mdiobus users with devres
Commit
ac3a68d56651 ("net: phy: don't abuse devres in
devm_mdiobus_register()") by Bartosz Golaszewski has introduced two
classes of potential bugs by making the devres callback of
devm_mdiobus_alloc stop calling mdiobus_unregister.
The exact buggy circumstances are presented in the individual commit
messages. I have searched the tree for other occurrences, but at the
moment:
- for issue (a) I have no concrete proof that other buses except SPI and
I2C suffer from it, and the only SPI or I2C device drivers that call
of_mdiobus_alloc are the DSA drivers that leave a NULL
ds->slave_mii_bus and a non-NULL ds->ops->phy_read, aka ksz9477,
ksz8795, lan9303_i2c, vsc73xx-spi.
- for issue (b), all drivers which call of_mdiobus_alloc either use
of_mdiobus_register too, or call mdiobus_unregister sometime within
the ->remove path.
Although at this point I've seen enough strangeness caused by this
"device_del during ->shutdown" that I'm just going to copy the SPI and
I2C subsystem maintainers to this patch series, to get their feedback
whether they've had reports about things like this before. I don't think
other buses behave in this way, it forces SPI and I2C devices to have to
protect themselves from a really strange set of issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 20 Sep 2021 21:42:09 +0000 (00:42 +0300)]
net: dsa: realtek: register the MDIO bus under devres
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, the Realtek drivers fall under category (b). To solve it,
we can register the MDIO bus under devres too, which restores the
previous behavior.
Fixes:
ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reported-by: Alvin Å ipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 20 Sep 2021 21:42:08 +0000 (00:42 +0300)]
net: dsa: don't allocate the slave_mii_bus using devres
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, DSA falls into category (a), it tries to be helpful and
registers an MDIO bus on behalf of the switch, which might be on such a
bus. I've no idea why it does it under devres.
It does this on probe:
if (!ds->slave_mii_bus && ds->ops->phy_read)
alloc and register mdio bus
and this on remove:
if (ds->slave_mii_bus && ds->ops->phy_read)
unregister mdio bus
I _could_ imagine using devres because the condition used on remove is
different than the condition used on probe. So strictly speaking, DSA
cannot determine whether the ds->slave_mii_bus it sees on remove is the
ds->slave_mii_bus that _it_ has allocated on probe. Using devres would
have solved that problem. But nonetheless, the existing code already
proceeds to unregister the MDIO bus, even though it might be
unregistering an MDIO bus it has never registered. So I can only guess
that no driver that implements ds->ops->phy_read also allocates and
registers ds->slave_mii_bus itself.
So in that case, if unregistering is fine, freeing must be fine too.
Stop using devres and free the MDIO bus manually. This will make devres
stop attempting to free a still registered MDIO bus on ->shutdown.
Fixes:
ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mianhan Liu [Tue, 21 Sep 2021 07:47:51 +0000 (15:47 +0800)]
net/ipv4/sysctl_net_ipv4.c: remove superfluous header files from sysctl_net_ipv4.c
sysctl_net_ipv4.c hasn't use any macro or function declared in igmp.h,
inetdevice.h, mm.h, module.h, nsproxy.h, swap.h, inet_frag.h, route.h
and snmp.h. Thus, these files can be removed from sysctl_net_ipv4.c
safely without affecting the compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masanari Iida [Tue, 21 Sep 2021 06:41:23 +0000 (15:41 +0900)]
Doc: networking: Fox a typo in ice.rst
This patch fixes a spelling typo in ice.rst
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 20 Sep 2021 22:49:18 +0000 (01:49 +0300)]
net: dsa: fix dsa_tree_setup error path
Since the blamed commit, dsa_tree_teardown_switches() was split into two
smaller functions, dsa_tree_teardown_switches and dsa_tree_teardown_ports.
However, the error path of dsa_tree_setup stopped calling dsa_tree_teardown_ports.
Fixes:
a57d8c217aad ("net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 21 Sep 2021 09:58:36 +0000 (10:58 +0100)]
Merge branch 'iddq-sr-mode'
Florian Fainelli says:
====================
net: phy: broadcom: IDDQ-SR mode
This patch series adds support for the IDDQ with soft recovery mode
which allows power savings of roughly 150mW compared to a simple
BMCR.PDOWN power off (called standby power down in Broadcom datasheets).
In order to leverage these modes we add a new PHY driver flags for
drivers to opt-in for that behavior, the PHY driver is modified to do
the appropriate programming and the PHYs on which this was tested get
updated to have an appropriate suspend/resume set of functions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 20 Sep 2021 21:54:18 +0000 (14:54 -0700)]
net: dsa: bcm_sf2: Request APD, DLL disable and IDDQ-SR
When interfacing with a Broadcom PHY, request the auto-power down, DLL
disable and IDDQ-SR modes to be enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 20 Sep 2021 21:54:17 +0000 (14:54 -0700)]
net: bcmgenet: Request APD, DLL disable and IDDQ-SR
When interfacing with a Broadcom PHY, request the auto-power down, DLL
disable and IDDQ-SR modes to be enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 20 Sep 2021 21:54:16 +0000 (14:54 -0700)]
net: phy: broadcom: Utilize appropriate suspend for BCM54810/11
Since we enable APD and DLL/RXC/TXC disable we need to use
bcm54xx_suspend() in order not to do a read/modify/write of the BMCR
register which is incompatible with the desired settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 20 Sep 2021 21:54:15 +0000 (14:54 -0700)]
net: phy: broadcom: Wire suspend/resume for BCM50610 and BCM50610M
These two Ethernet PHYs support IDDQ-SR therefore wire-up the suspend
and resume callbacks to point to bcm54xx_suspend() and bcm54xx_resume().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 20 Sep 2021 21:54:14 +0000 (14:54 -0700)]
net: phy: broadcom: Add IDDQ-SR mode
Add support for putting the PHY into IDDQ Soft Recovery mode by setting
the TOP_MISC register bits accordingly. This requires us to implement a
custom bcm54xx_suspend() routine which diverges from genphy_suspend() in
order to configure the PHY to enter IDDQ with software recovery as well
as avoid doing a read/modify/write on the BMCR register.
Doing a read/modify/write on the BMCR register means that the
auto-negotation bit may remain which interferes with the ability to put
the PHY into IDDQ-SR mode. We do software reset upon suspend in order to
put the PHY back into its state prior to suspend as recommended by the
datasheet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 21 Sep 2021 09:54:17 +0000 (10:54 +0100)]
Merge branch 'smc-fixes'
Karsten Graul says:
====================
net/smc: fixes 2021-09-20
Please apply the following patches for smc to netdev's net tree.
The first patch adds a missing error check, and the second patch
fixes a possible leak of a lock in a worker.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 20 Sep 2021 19:18:15 +0000 (21:18 +0200)]
net/smc: fix 'workqueue leaked lock' in smc_conn_abort_work
The abort_work is scheduled when a connection was detected to be
out-of-sync after a link failure. The work calls smc_conn_kill(),
which calls smc_close_active_abort() and that might end up calling
smc_close_cancel_work().
smc_close_cancel_work() cancels any pending close_work and tx_work but
needs to release the sock_lock before and acquires the sock_lock again
afterwards. So when the sock_lock was NOT acquired before then it may
be held after the abort_work completes. Thats why the sock_lock is
acquired before the call to smc_conn_kill() in __smc_lgr_terminate(),
but this is missing in smc_conn_abort_work().
Fix that by acquiring the sock_lock first and release it after the
call to smc_conn_kill().
Fixes:
b286a0651e44 ("net/smc: handle incoming CDC validation message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Mon, 20 Sep 2021 19:18:14 +0000 (21:18 +0200)]
net/smc: add missing error check in smc_clc_prfx_set()
Coverity stumbled over a missing error check in smc_clc_prfx_set():
*** CID
1475954: Error handling issues (CHECKED_RETURN)
/net/smc/smc_clc.c: 233 in smc_clc_prfx_set()
>>> CID
1475954: Error handling issues (CHECKED_RETURN)
>>> Calling "kernel_getsockname" without checking return value (as is done elsewhere 8 out of 10 times).
233 kernel_getsockname(clcsock, (struct sockaddr *)&addrs);
Add the return code check in smc_clc_prfx_set().
Fixes:
c246d942eabc ("net/smc: restructure netinfo for CLC proposal msgs")
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mianhan Liu [Mon, 20 Sep 2021 14:15:49 +0000 (22:15 +0800)]
net/ipv4/syncookies.c: remove superfluous header files from syncookies.c
syncookies.c hasn't use any macro or function declared in slab.h and random.h,
Thus, these files can be removed from syncookies.c safely without
affecting the compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mianhan Liu [Mon, 20 Sep 2021 12:29:57 +0000 (20:29 +0800)]
net/ipv4/udp_tunnel_core.c: remove superfluous header files from udp_tunnel_core.c
udp_tunnel_core.c hasn't use any macro or function declared in udp.h, types.h,
and net_namespace.h. Thus, these files can be removed from udp_tunnel_core.c
safely without affecting the compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 20 Sep 2021 22:49:02 +0000 (15:49 -0700)]
Merge tag 'afs-fixes-
20210913' of git://git./linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
"Fixes for AFS problems that can cause data corruption due to
interaction with another client modifying data cached locally:
- When d_revalidating a dentry, don't look at the inode to which it
points. Only check the directory to which the dentry belongs. This
was confusing things and causing the silly-rename cleanup code to
remove the file now at the dentry of a file that got deleted.
- Fix mmap data coherency. When a callback break is received that
relates to a file that we have cached, the data content may have
been changed (there are other reasons, such as the user's rights
having been changed). However, we're checking it lazily, only on
entry to the kernel, which doesn't happen if we have a writeable
shared mapped page on that file.
We make the kernel keep track of mmapped files and clear all PTEs
mapping to that file as soon as the callback comes in by calling
unmap_mapping_pages() (we don't necessarily want to zap the
pagecache). This causes the kernel to be reentered when userspace
tries to access the mmapped address range again - and at that point
we can query the server and, if we need to, zap the page cache.
Ideally, I would check each file at the point of notification, but
that involves poking the server[*] - which is holding an exclusive
lock on the vnode it is changing, waiting for all the clients it
notified to reply. This could then deadlock against the server.
Further, invalidating the pagecache might call ->launder_page(),
which would try to write to the file, which would definitely
deadlock. (AFS doesn't lease file access).
[*] Checking to see if the file content has changed is a matter of
comparing the current data version number, but we have to ask
the server for that. We also need to get a new callback promise
and we need to poke the server for that too.
- Add some more points at which the inode is validated, since we're
doing it lazily, notably in ->read_iter() and ->page_mkwrite(), but
also when performing some directory operations.
Ideally, checking in ->read_iter() would be done in some derivation
of filemap_read(). If we're going to call the server to read the
file, then we get the file status fetch as part of that.
- The above is now causing us to make a lot more calls to
afs_validate() to check the inode - and afs_validate() takes the
RCU read lock each time to make a quick check (ie.
afs_check_validity()). This is entirely for the purpose of checking
cb_s_break to see if the server we're using reinitialised its list
of callbacks - however this isn't a very common event, so most of
the time we're taking this needlessly.
Add a new cell-wide counter to count the number of
reinitialisations done by any server and check that - and only if
that changes, take the RCU read lock and check the server list (the
server list may change, but the cell a file is part of won't).
- Don't update vnode->cb_s_break and ->cb_v_break inside the validity
checking loop. The cb_lock is done with read_seqretry, so we might
go round the loop a second time after resetting those values - and
that could cause someone else checking validity to miss something
(I think).
Also included are patches for fixes for some bugs encountered whilst
debugging this:
- Fix a leak of afs_read objects and fix a leak of keys hidden by
that.
- Fix a leak of pages that couldn't be added to extend a writeback.
- Fix the maintenance of i_blocks when i_size is changed by a local
write or a local dir edit"
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214217
Link: https://lore.kernel.org/r/163111665183.283156.17200205573146438918.stgit@warthog.procyon.org.uk/
Link: https://lore.kernel.org/r/163113612442.352844.11162345591911691150.stgit@warthog.procyon.org.uk/
* tag 'afs-fixes-
20210913' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix updating of i_blocks on file/dir extension
afs: Fix corruption in reads at fpos 2G-4G from an OpenAFS server
afs: Try to avoid taking RCU read lock when checking vnode validity
afs: Fix mmap coherency vs 3rd-party changes
afs: Fix incorrect triggering of sillyrename on 3rd-party invalidation
afs: Add missing vnode validation checks
afs: Fix page leak
afs: Fix missing put on afs_read objects and missing get on the key therein
Linus Torvalds [Mon, 20 Sep 2021 22:35:17 +0000 (15:35 -0700)]
Merge tag '5.15-rc1-ksmbd' of git://git.samba.org/ksmbd
Pull ksmbd server fixes from Steve French:
"Three ksmbd fixes, including an important security fix for path
processing, and a buffer overflow check, and a trivial fix for
incorrect header inclusion"
* tag '5.15-rc1-ksmbd' of git://git.samba.org/ksmbd:
ksmbd: add validation for FILE_FULL_EA_INFORMATION of smb2_get_info
ksmbd: prevent out of share access
ksmbd: transport_rdma: Don't include rwlock.h directly
Linus Torvalds [Mon, 20 Sep 2021 22:30:29 +0000 (15:30 -0700)]
Merge tag '5.15-rc1-smb3' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
- two deferred close fixes (for bugs found with xfstests 478 and 461)
- a deferred close improvement in rename
- two trivial fixes for incorrect Linux comment formatting of multiple
cifs files (pointed out by automated kernel test robot and
checkpatch)
* tag '5.15-rc1-smb3' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Not to defer close on file when lock is set
cifs: Fix soft lockup during fsstress
cifs: Deferred close performance improvements
cifs: fix incorrect kernel doc comments
cifs: remove pathname for file from SPDX header
Linus Torvalds [Mon, 20 Sep 2021 19:14:33 +0000 (12:14 -0700)]
Merge tag 'spi-fix-v5.15-rc2' of git://git./linux/kernel/git/broonie/spi
Pull spi fixes from Mark BrownL
"This contains a couple of fixes, one fix for handling of zero length
transfers on Rockchip devices and a warning fix which will conflict
with a version you did but cleans up some extra unneeded forward
declarations as well which seems a bit neater"
* tag 'spi-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: tegra20-slink: Declare runtime suspend and resume functions conditionally
spi: rockchip: handle zero length transfers without timing out
Linus Torvalds [Mon, 20 Sep 2021 18:47:41 +0000 (11:47 -0700)]
Merge tag 'regulator-fix-v5.15-rc2' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small device specific fixes that have been sent since the
merge window, neither of which stands out particularly"
* tag 'regulator-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: max14577: Revert "regulator: max14577: Add proper module aliases strings"
regulator: qcom-rpmh-regulator: fix pm8009-1 ldo7 resource name
Guenter Roeck [Wed, 8 Sep 2021 19:08:17 +0000 (12:08 -0700)]
drm/nouveau/nvkm: Replace -ENOSYS with -ENODEV
nvkm test builds fail with the following error.
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c: In function 'nvkm_control_mthd_pstate_info':
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c:60:35: error: overflow in conversion from 'int' to '__s8' {aka 'signed char'} changes value from '-251' to '5'
The code builds on most architectures, but fails on parisc where ENOSYS
is defined as 251.
Replace the error code with -ENODEV (-19). The actual error code does
not really matter and is not passed to userspace - it just has to be
negative.
Fixes:
7238eca4cf18 ("drm/nouveau: expose pstate selection per-power source in sysfs")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 20 Sep 2021 17:56:32 +0000 (10:56 -0700)]
sparc64: fix pci_iounmap() when CONFIG_PCI is not set
Guenter reported [1] that the pci_iounmap() changes remain problematic,
with sparc64 allnoconfig and tinyconfig still not building due to the
header file changes and confusion with the arch-specific pci_iounmap()
implementation.
I'm pretty convinced that sparc should just use GENERIC_IOMAP instead of
doing its own thing, since it turns out that the sparc64 version of
pci_iounmap() is somewhat buggy (see [2]). But in the meantime, this
just fixes the build by avoiding the trivial re-definition of the empty
case.
Link: https://lore.kernel.org/lkml/20210920134424.GA346531@roeck-us.net/
Link: https://lore.kernel.org/lkml/CAHk-=wgheheFx9myQyy5osh79BAazvmvYURAtub2gQtMvLrhqQ@mail.gmail.com/
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Mon, 20 Sep 2021 12:28:50 +0000 (13:28 +0100)]
Merge branch 'hns3-fixes'
Guangbin Huang says:
====================
net: hns3: add some fixes for -net
This series adds some fixes for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Wed, 15 Sep 2021 13:52:11 +0000 (21:52 +0800)]
net: hns3: fix a return value error in hclge_get_reset_status()
hclge_get_reset_status() should return the tqp reset status.
However, if the CMDQ fails, the caller will take it as tqp reset
success status by mistake. Therefore, uses a parameters to get
the tqp reset status instead.
Fixes:
46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
liaoguojia [Wed, 15 Sep 2021 13:52:10 +0000 (21:52 +0800)]
net: hns3: check vlan id before using it
The input parameters may not be reliable, so check the vlan id before
using it, otherwise may set wrong vlan id into hardware.
Fixes:
dc8131d846d4 ("net: hns3: Fix for packet loss due wrong filter config in VLAN tbls")
Signed-off-by: liaoguojia <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Wed, 15 Sep 2021 13:52:09 +0000 (21:52 +0800)]
net: hns3: check queue id range before using
The input parameters may not be reliable. Before using the
queue id, we should check this parameter. Otherwise, memory
overwriting may occur.
Fixes:
d34100184685 ("net: hns3: refactor the mailbox message between PF and VF")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiaran Zhang [Wed, 15 Sep 2021 13:52:08 +0000 (21:52 +0800)]
net: hns3: fix misuse vf id and vport id in some logs
vport_id include PF and VFs, vport_id = 0 means PF, other values mean VFs.
So the actual vf id is equal to vport_id minus 1.
Some VF print logs are actually vport, and logs of vf id actually use
vport id, so this patch fixes them.
Fixes:
ac887be5b0fe ("net: hns3: change print level of RAS error log from warning to error")
Fixes:
adcf738b804b ("net: hns3: cleanup some print format warning")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Wed, 15 Sep 2021 13:52:07 +0000 (21:52 +0800)]
net: hns3: fix inconsistent vf id print
The vf id from ethtool is added 1 before configured to driver.
So it's necessary to minus 1 when printing it, in order to
keep consistent with user's configuration.
Fixes:
dd74f815dd41 ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Wed, 15 Sep 2021 13:52:06 +0000 (21:52 +0800)]
net: hns3: fix change RSS 'hfunc' ineffective issue
When user change rss 'hfunc' without set rss 'hkey' by ethtool
-X command, the driver will ignore the 'hfunc' for the hkey is
NULL. It's unreasonable. So fix it.
Fixes:
46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes:
374ad291762a ("net: hns3: Add RSS general configuration support for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mianhan Liu [Mon, 20 Sep 2021 11:55:36 +0000 (19:55 +0800)]
net/ipv4/tcp_minisocks.c: remove superfluous header files from tcp_minisocks.c
tcp_minisocks.c hasn't use any macro or function declared in mm.h, module.h,
slab.h, sysctl.h, workqueue.h, static_key.h and inet_common.h. Thus, these
files can be removed from tcp_minisocks.c safely without affecting the
compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mianhan Liu [Mon, 20 Sep 2021 11:34:16 +0000 (19:34 +0800)]
net/ipv4/tcp_fastopen.c: remove superfluous header files from tcp_fastopen.c
tcp_fastopen.c hasn't use any macro or function declared in crypto.h, err.h,
init.h, list.h, rculist.h and inetpeer.h. Thus, these files can be removed
from tcp_fastopen.c safely without affecting the compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mianhan Liu [Mon, 20 Sep 2021 11:31:37 +0000 (19:31 +0800)]
net/ipv4/route.c: remove superfluous header files from route.c
route.c hasn't use any macro or function declared in uaccess.h, types.h,
string.h, sockios.h, times.h, protocol.h, arp.h and l3mdev.h. Thus, these
files can be removed from route.c safely without affecting the compilation
of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 20 Sep 2021 09:57:49 +0000 (11:57 +0200)]
ptp: ocp: add COMMON_CLK dependency
Without CONFIG_COMMON_CLK, this fails to link:
arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_register_i2c':
ptp_ocp.c:(.text+0xcc0): undefined reference to `__clk_hw_register_fixed_rate'
arm-linux-gnueabi-ld: ptp_ocp.c:(.text+0xcf4): undefined reference to `devm_clk_hw_register_clkdev'
arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_detach':
ptp_ocp.c:(.text+0x1c24): undefined reference to `clk_hw_unregister_fixed_rate'
Fixes:
a7e1abad13f3 ("ptp: Add clock driver for the OpenCompute TimeCard.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 20 Sep 2021 06:51:52 +0000 (02:51 -0400)]
bnxt_en: Fix TX timeout when TX ring size is set to the smallest
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes:
c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksander Jan Bajkowski [Sun, 19 Sep 2021 18:24:28 +0000 (20:24 +0200)]
net: lantiq: add support for jumbo frames
Add support for jumbo frames. Full support for jumbo frames requires
changes in the DSA switch driver (lantiq_gswip.c).
Tested on BT Hone Hub 5A.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 20 Sep 2021 09:04:01 +0000 (10:04 +0100)]
Merge branch 'wwan-iosm-fw-flashing'
M Chetan Kumar says:
====================
net: wwan: iosm: fw flashing & cd collection
This patch series brings-in support for M.2 7560 Device firmware flashing &
coredump collection using devlink.
- Driver Registers with Devlink framework.
- Register devlink params callback for configuring device params
required in flashing or coredump flow.
- Implements devlink ops flash_update callback that programs modem
firmware.
- Creates region & snapshot required for device coredump log collection.
On early detection of device in boot rom stage. Driver registers with
Devlink framework and establish transport channel for PSI (Primary Signed
Image) injection. Once PSI is injected to device, the device execution
stage details are read to determine whether device is in flash or
exception mode. The collected information is reported to devlink user
space application & based on this informationi, application proceeds with
either modem firmware flashing or coredump collection.
Refer to iosm devlink documentation for details on Devlink Params, flash
update and coredump collection command usage.
Note: Patches are interdependent. Need to apply complete patch series for
compilation.
Changes since v1:
* Break down single patch into multiple patches.
* IOSM Driver devlink documentation.
* Fixes NULL parameter deference in ipc_devlink_flash_update() reported
by smatch static checker.
* Fixes memory leak in ipc_devlink_create_region().
* Use kmemdup instead of kzalloc and memcpy in ipc_flash_boot_psi().
* Fixes linux-net build error.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Sun, 19 Sep 2021 17:28:35 +0000 (22:58 +0530)]
net: wwan: iosm: fw flashing & cd collection infrastructure changes
IOSM Makefile & WWAN Kconfig changes to support fw flashing & cd
collection module compliation.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Sun, 19 Sep 2021 17:28:18 +0000 (22:58 +0530)]
net: wwan: iosm: devlink fw flashing & cd collection documentation
Documents devlink params, fw update & cd collection commands
and its usage.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Sun, 19 Sep 2021 17:27:56 +0000 (22:57 +0530)]
net: wwan: iosm: transport layer support for fw flashing/cd
Implements transport layer protocol for fw flashing/coredump
collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Sun, 19 Sep 2021 17:27:27 +0000 (22:57 +0530)]
net: wwan: iosm: coredump collection support
Implements protocol for coredump collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Sun, 19 Sep 2021 17:27:05 +0000 (22:57 +0530)]
net: wwan: iosm: fw flashing support
Implements protocol for fw flashing and PSI injection for
coredump collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Sun, 19 Sep 2021 17:26:18 +0000 (22:56 +0530)]
net: wwan: iosm: devlink registration
Register with devlink framework and implment callbacks required
for fw flashing and coredump collection.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Sun, 19 Sep 2021 16:28:17 +0000 (18:28 +0200)]
net: phy: at803x: fix spacing and improve name for 83xx phy
Fix spacing and improve name for 83xx phy following other phy in the
same driver.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>