OSDN Git Service
Arnd Bergmann [Wed, 25 Mar 2020 21:22:47 +0000 (22:22 +0100)]
Merge tag 'imx-dt64-5.7' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 DTS update for 5.7:
- New support for Kontron LS1028A based boards and NXP i.MX8MP EVK.
- Add Ethernet PHY reset GPIO for imx8mm-evk and imx8mq-evk board.
- Add gpio-fan, thermal and Ethernet support for imx8mq-phanbell board.
- Add SNVS clock description to pwrkey device for i.MX8 SoCs.
- A number of updates on librem5-devkit board to add audio, proximity
sensor, lsm9ds1 mount matrix support, and improve WoWWAN, DVFS, SD
devices as well.
- A series of patches from Anson Huang to update i.MX8 EVK boards
for support of I2C PCA6416, thermal, GPIO LED, OPP table etc.
- Add PCIe device nodes for LX2160A and LS1028A SoC.
- Add FSPI deivce support for LX2160A evaluation boards.
- Add EEPROM and LTC3882 regulator support for lx2160a-cex7 board.
- Other small and random updates on LS1028A and i.MX8 support.
* tag 'imx-dt64-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (63 commits)
arm64: dts: ls1028a: disable the felix switch by default
arm64: dts: imx8mp: Add snvs clock to powerkey
arm64: dts: imx8mn: Add snvs clock to powerkey
arm64: dts: ls1028a: Add PCIe controller DT nodes
arm64: dts: ls1028a: sl28: add support for variant 2
arm64: dts: ls1028a: sl28: expose switch ports in KBox A-230-LS
arm64: dts: ls1028a: sl28: fix on-board EEPROMS
arm64: dts: freescale: sl28: add SPI flash
arm64: dts: imx8m: fix aips dts node
arm64: dts: imx8mn: Add CPU thermal zone support
arm64: dts: imx8mm: Add thermal zone support
arm64: dts: imx8mq-phanbell: Fix Ethernet PHY post-reset duration
arm64: dts: enable fspi in imx8mm dts
arm64: dts: imx8mn: align name for crypto child nodes
arm64: dts: lx2160aqds: Add FSPI node properties
arm64: dts: lx2160ardb: Update FSPI node properties
arm64: dts: imx8mq-phanbell: Add gpio-fan/thermal support
arm64: dts: layerscape: add iommu-map property to pci nodes
arm64: dts: imx8mp-evk: Enable pca6416 on i2c3 bus
arm64: dts: imx8mp-evk: Add i2c3 support
...
Link: https://lore.kernel.org/r/20200318051918.32579-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 21:21:21 +0000 (22:21 +0100)]
Merge tag 'imx-dt-5.7' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm DTS changes for 5.7:
- New support for i.MX6/7 based PICO devices and Toradex i.MX7 based
Aster boards.
- Add voltage monitor device node for vf610-zii boards.
- Improve UART pins macro defines for i.MX6SX SoC and switch related
boards to use the new names.
- Use generic node name for devices like GPT, KPP, CCM, WDOG, OCOTP and
IOMUXC in i.MX DTS files.
- Switch imx6ul-pico device tree to DRM bindings.
- Use SPDX-License-Identifier for all Toradex i.MX6/7 based boards.
- Add proper rgmii PHY description for imx6dl-riotboard and
imx6q-marsboard.
- Add capture-subsystem device support for i.MX51.
- Kill off "simple-panel" compatibles which has never been an accepted
as an upstream compatible string.
- Random device addition to various boards.
* tag 'imx-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (55 commits)
ARM: dts: imx6q-marsboard: properly define rgmii PHY
ARM: dts: imx6dl-riotboard: properly define rgmii PHY
ARM: dts: imx51-zii-rdu1: set name prefix for TPA6130A2
ARM: dts: imx6: RDU2: assign video PLL as input to LDB
ARM: dts: vf: toradex: SPDX tags and copyright cleanup
ARM: dts: imx7: toradex: use SPDX-License-Identifier
ARM: dts: imx6: toradex: use SPDX-License-Identifier
ARM: dts: imx51: add capture-subsystem device
ARM: dts: imx: add nvmem property for cpu0
ARM: dts: imx6qdl: Add imx6qdl-pico support
ARM: dts: imx6ul-pico: Add support for the dwarf baseboard
ARM: dts: imx7d-pico: Add support for the nymph baseboard
ARM: dts: imx7d-pico: Add support for the dwarf baseboard
ARM: dts: imx23: introduce mmc0_sck_cfg
ARM: dts: imx25-pinfunc: add config for kpp rows 4 to 7
ARM: dts: imx: align name for crypto node and child nodes
ARM: dts: imx6qdl-gw5910: add CC1352 UART
ARM: dts: imx6qdl-sr-som-ti: indicate powering off wifi is safe
ARM: dts: imx6: phycore-som: add da9062 gpio support
ARM: dts: imx6: phycore-som: explicit disable pmic watchdog during suspend
...
Link: https://lore.kernel.org/r/20200318051918.32579-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 21:20:01 +0000 (22:20 +0100)]
Merge tag 'imx-bindings-5.7' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT bindings update for 5.7:
- Add compatibles for TechNexion i.MX6/7, Kontron LS1028A, Toradex i.MX7,
NXP i.MX8MP EVK, and LS1028A evaluation boards.
- Improve NXP crypto binding examples to use generic node name.
* tag 'imx-bindings-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: Add TechNexion boards
dt-bindings: crypto: caam: use generic node name
dt-bindings: crypto: dcp: use generic node name
dt-bindings: crypto: sahara: use generic node name
dt-bindings: arm: fsl: add nxp based toradex colibri-imx7 bindings
dt-bindings: arm: imx: Add the i.MX8MP EVK board
dt-bindings: arm: fsl: add Kontron sl28 boards
dt-bindings: arm: fsl: add LS1028A based boards
Link: https://lore.kernel.org/r/20200318051918.32579-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 21:19:04 +0000 (22:19 +0100)]
Merge tag 'uniphier-dt64-v5.7' of git://git./linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM64 SoC DT updates for v5.7
- Rename nodes to avoid dt-schema warnings
- Enable SPI for PXs3 reference board
- Enable thermal monitor for PXs3 SoC
- Fix clock and reset of SPI nodes
* tag 'uniphier-dt64-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: Set SCSSI clock and reset IDs for each channel
arm64: dts: uniphier: Add nodes of thermal monitor and thermal zone for PXs3
arm64: dts: uniphier: Enable spi node for PXs3 reference board
arm64: dts: uniphier: rename NAND node names to follow json-schema
arm64: dts: uniphier: rename aidet node names to follow json-schema
arm64: dts: uniphier: change SD/eMMC node names to follow json-schema
Link: https://lore.kernel.org/r/CAK7LNASMD-zqNfG02WhU1LeAJevnjBv=oT2N_7y6C8w7kryotQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 21:16:56 +0000 (22:16 +0100)]
Merge tag 'uniphier-dt-v5.7' of git://git./linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM SoC DT updates for v5.7
- Rename nodes to avoid dt-schema warnings
- Add a generic compatible to EEPROM so that it matches OF table
- Add USB controller nodes to Pro5 SoC
- Fix clock and reset of SPI nodes
* tag 'uniphier-dt-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: Set SCSSI clock and reset IDs for each channel
ARM: dts: uniphier: Add USB3 controller nodes for Pro5
ARM: dts: uniphier: Add one more generic compatible string for I2C EEPROM
ARM: dts: uniphier: rename cache controller nodes to follow json-schema
ARM: dts: uniphier: rename NAND node names to follow json-schema
ARM: dts: uniphier: rename aidet node names to follow json-schema
ARM: dts: uniphier: change SD/eMMC node names to follow json-schema
Link: https://lore.kernel.org/r/CAK7LNAQ-AOTyqpV1E_S-hksjqexHfVauwGV9rrfDvjRVnu8-UQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 21:03:01 +0000 (22:03 +0100)]
Merge tag 'amlogic-dt64' of git://git./linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: Amlogic updates for v5.7
- sound, bluetooth, thermal updates
- A1: add secure power domain nodes
- misc. cleanups
* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: add thermal zones to meson gx devices
arm64: dts: meson: khadas-vim3: move model to g12b-khadas-vim3 dtsi
arm64: dts: meson-g12b: fix N2/VIM3 audio card model names
arm64: dts: meson-gxbb-vega-s95: fix bluetooth node
arm64: dts: meson-gxl-s905x-p212: add bluetooth nodes
arm64: dts: meson-gxbb-odroid-c2: add rc-odroid ir keymap
arm64: dts: meson: fix gxm-khadas-vim2 wifi
arm64: dts: meson: sei510: fix sound card codec node
arm64: dts: meson: s400: fix sound card codec nodes
arm64: dts: meson: add pdm reset line
arm64: dts: g12-common: add parkmode_disable_ss_quirk on DWC3 controller
arm64: dts: amlogic: add rc-videostrong-kii-pro keymap
arm64: dts: meson: a1: add secure power domain controller
Link: https://lore.kernel.org/r/7hlfo0ugnj.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 21:01:56 +0000 (22:01 +0100)]
Merge tag 'v5.7-rockchip-dts64-1' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
Support for the rk3399-based Pinebook Pro, eDP support and power-tree for
the rk3399 evaluation board, a big number of fixes for issues found by
checking against the new yaml dt-bindings.
And on the smaller side, fixes for network transfers, the mute gpio
on rk3328 gets actually described and one lvds fix on the px30 and
the rk3399-hugsun board gets IR and power led.
* tag 'v5.7-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (27 commits)
arm64: dts: rockchip: Add Hugsun X99 power led
arm64: dts: rockchip: Add Hugsun X99 IR receiver
arm64: dts: rockchip: remove clock-names property from 'generic-ohci' nodes
arm64: dts: rockchip: remove clock-names property from 'generic-ehci' nodes
arm64: dts: rockchip: remove properties from spdif node RK3399 Excavator
arm64: dts: add bus to rockchip amba nodenames
arm64: dts: rockchip: replace clock-freq-min-max by max-frequency
arm64: dts: rockchip: fix vqmmc-supply property name for rk3399 puma
arm64: dts: remove no-emmc from mmc node for Rockchip PX5 EVB
arm64: dts: rockchip: remove rockchip,grf from vop nodes for px30
arm64: dts: rockchip: remove max-freq from &spi1 node for Hugsun X99
arm64: dts: rockchip: fix compatible property for rk3399-evb
arm64: dts: rockchip: Add initial support for Pinebook Pro
dt-bindings: Add doc for Pine64 Pinebook Pro
arm64: dts: rockchip: Enable eDP display on rk3399 evb
arm64: dts: rockchip: remove enable-gpio of backlight on rk3399 evb
arm64: dts: rockchip: Add pmic dt tree for rk3399 evb
arm64: dts: rockchip: remove dvs2 pinctrl for pmic on rk3399 evb
arm64: dts: rockchip: fix px30 lvds ports
arm64: dts: rockchip: Add txpbl node for RK3399/RK3328
...
Link: https://lore.kernel.org/r/27799037.pT45f1LVdF@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:58:18 +0000 (21:58 +0100)]
Merge tag 'v5.7-rockchip-dts32-1' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
Improvements for the rk3288-vyasa board and a lot of cleanups from
verifying devicetrees against new yaml bindings.
* tag 'v5.7-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (25 commits)
ARM: dts: rockchip: remove #address-cells and #size-cells from i2s nodes
ARM: dts: rockchip: swap clocks and clock-names values for i2s nodes
ARM: dts: rockchip: remove clock-names property from 'generic-ohci' nodes
ARM: dts: rockchip: remove clock-names property from 'generic-ehci' nodes
ARM: dts: rockchip: swap clocks and clock-names values for spdif nodes
ARM: dts: rockchip: Keep rk3288-tinker SD card IO powered during reboot
ARM: dts: rockchip: remove clock-frequency from saradc node rv1108
ARM: dts: rockchip: fix vref-supply for &saradc node rk3288 firefly reload
ARM: dts: rockchip: use DMA channels for UARTs for RK3288
ARM: dts: rockchip: rk3xxx: fix L2 cache-controller nodename
ARM: dts: rockchip: fix lvds-encoder ports subnode for rk3188-bqedison2qc
ARM: dts: add bus to rockchip amba nodenames
ARM: dts: rockchip: remove #dma-cells from dma client nodes for rv1108
ARM: dts: rockchip: fix rockchip,default-sample-phase property names
ARM: dts: rockchip: fix vqmmc-supply property name for rk3188-bqedison2qc
dt-bindings: arm: add Rockchip rk3036-evb board
dt-bindings: arm: fix Rockchip Kylin board bindings
ARM: dts: rockchip: add missing model properties
ARM: dts: rockchip: Add vcc50_hdmi for rk3288-vyasa
ARM: dts: rockchip: Fix ddc-i2c-bus for rk3288-vyasa
...
Link: https://lore.kernel.org/r/7846023.TtVhTo4ACP@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:52:09 +0000 (21:52 +0100)]
Merge tag 'samsung-dt-5.7' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.7
1. Various fixes:
- Reboot of some Odroid Exynos4412-based boards,
- MMC regulators on Arndale5250,
- Memory mapping on Artik5,
- GPU power domain on Exynos542x boards,
- LCD SPI polarity on UniversalC210,
2. Add thermal cooling of GPU on Odroid XU3/XU4 family,
3. Add dynamic-power-coefficient to Exynos5422 for energy model.
* tag 'samsung-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix polarity of the LCD SPI bus on UniversalC210 board
ARM: dts: exynos: Fix G3D power domain supply on Arndale Octa boards
ARM: dts: exynos: Fix G3D power domain supply on Odroid XU3/XU4/HC1 boards
ARM: dts: exynos: Fix memory on Artik5 evaluation boards
ARM: dts: exynos: Make fixed regulators always-on on Arndale5250
ARM: dts: exynos: Fix MMC regulator on Arndale5250 board
ARM: dts: exynos: Add dynamic-power-coefficient to Exynos5422 CPUs
ARM: dts: exynos: Add GPU thermal zone cooling maps for Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix broken reboot on some Odroid U2/X2/U3 boards
Link: https://lore.kernel.org/r/20200316175652.5604-3-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:49:53 +0000 (21:49 +0100)]
Merge tag 'ux500-dts-v5.7' of git://git./linux/kernel/git/linusw/linux-stericsson into arm/dt
Ux500 DTS updates for the v5.7 kernel:
- Fix some DSI nodes
- Add GT-S7710 DTS file
* tag 'ux500-dts-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: Add devicetree for Samsung GT-S7710
ARM: dts: ux500: Fix up DSI controller nodes
Link: https://lore.kernel.org/r/CACRpkdb8T9CZYvYEFYnQTOMoXGsn43N8TgKfvoJZjTwRHW6zhQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:49:11 +0000 (21:49 +0100)]
Merge tag 'mvebu-dt64-5.7-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt64 for 5.7 (part 1)
Improve network support on two Armada 8040 based board:
Clearfog GT 8 and Macchiatobin.
Add ethernet alias on Espressobin for U-Boot support.
Fix various dt compilation issue or warning.
* tag 'mvebu-dt64-5.7-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: Fix cpu compatible for AP807-quad
arm64: dts: marvell: fix non-existed cpu referrence in armada-ap806-dual.dtsi
arm64: dts: marvell: build ESPRESSObin variants
arm64: dts: marvell: espressobin: indicate dts version
arm64: dts: marvell: espressobin: add ethernet alias
arm64: dts: mcbin: support 2W SFP modules
arm64: dts: clearfog-gt-8k: set gigabit PHY reset deassert delay
Link: https://lore.kernel.org/r/87h7yqx7w2.fsf@FE-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:48:17 +0000 (21:48 +0100)]
Merge tag 'tegra-for-5.7-arm64-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.7-rc1
These changes add support for the XUSB pad controller, as well as the
XUSB controller on Tegra194. Furthermore, USB device mode is supported
across Tegra210 and Tegra186 boards. PCIe endpoint mode support is added
for the Jetson AGX Xavier platform.
Various minor fixes eliminate warnings on boot related to missing power
supplies for some devices.
* tag 'tegra-for-5.7-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add support for PCIe endpoint mode in P2972-0000 platform
arm64: tegra: Add PCIe endpoint controllers nodes for Tegra194
arm64: tegra: Add ethernet alias on Jetson TX1
arm64: tegra: Populate LP8557 backlight regulator
arm64: tegra: Fix Tegra186 SOR supply
arm64: tegra: Add EEPROM supplies
arm64: tegra: Enable I2C controller for EEPROM
arm64: tegra: smaug: Change clk_out_2 provider to PMC
arm64: tegra: Add clock-cells property to Tegra PMC node
arm64: tegra: Enable XUDC node on Jetson Nano
arm64: tegra: Update OTG port entries for Jetson Nano
arm64: tegra: Enable XUDC node on Jetson TX2
arm64: tegra: Add XUDC node for Tegra186
arm64: tegra: Enable XUDC on Jetson TX1
arm64: tegra: Add XUDC node for Tegra210
arm64: tegra: Update OTG port entries for Jetson TX2
arm64: tegra: Update OTG port entries for Jetson TX1
arm64: tegra: Enable XUSB host in P2972-0000 board
arm64: tegra: Add XUSB and pad controller on Tegra194
arm64: tegra: Fix Tegra194 PCIe compatible string
Link: https://lore.kernel.org/r/20200313165848.2915133-8-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:47:16 +0000 (21:47 +0100)]
Merge tag 'tegra-for-5.7-arm-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.7-rc1
Minor fixes and additions for 32-bit Tegra SoC device trees.
* tag 'tegra-for-5.7-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Update sound node clocks in device tree
ARM: tegra: Add clock-cells property to PMC
ARM: tegra: Remove USB 2-0 port from Jetson TK1 padctl
Link: https://lore.kernel.org/r/20200313165848.2915133-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:46:11 +0000 (21:46 +0100)]
Merge tag 'tegra-for-5.7-dt-bindings' of git://git./linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.7-rc1
New IDs are added for clocks that are controlled by the PMC. This
replaces older IDs that were erroneously provided by the clock and reset
controller.
This also adds device tree bindings for XUSB pad controller support on
Tegra194 as well as USB role switching on NVIDIA Tegra SoCs.
* tag 'tegra-for-5.7-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: usb: Add NVIDIA Tegra XUSB device mode controller binding
dt-bindings: phy: tegra-xusb: Add usb-role-switch
dt-bindings: phy: tegra: Add Tegra194 support
dt-bindings: soc: tegra-pmc: Add ID for Tegra PMC 32 kHz blink clock
dt-bindings: soc: tegra-pmc: Add Tegra PMC clock bindings
dt-bindings: tegra: Convert Tegra PMC bindings to YAML
dt-bindings: clock: tegra: Add IDs for OSC clocks
Link: https://lore.kernel.org/r/20200313165848.2915133-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:45:02 +0000 (21:45 +0100)]
Merge tag 'stm32-dt-for-v5.7-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.3, round 1
Highlights:
----------
- Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. It is based on stm32mp157c SoC.
- Add OTG full support on stm32mp15.
- Fix issues seen during yaml validation on stpmic and stmfx.
- Add i2c power/wakeup support on stm32mp15.
- Add card detect on sdcard on stm32mp boards
* tag 'stm32-dt-for-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (25 commits)
ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
ARM: dts: stm32: Correct stmfx node name on stm32746g-eval board
ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
ARM: dts: stm32: add USB OTG full support on stm32mp151
ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board
...
Link: https://lore.kernel.org/r/ded09d01-df47-9572-4679-34669bff8916@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:44:14 +0000 (21:44 +0100)]
Merge tag 'renesas-dt-bindings-for-v5.7-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.7
- Document support for the M3ULCB board with R-Car M3-W+.
* tag 'renesas-dt-bindings-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: arm: renesas: Add M3ULCB with R-Car M3-W+
Link: https://lore.kernel.org/r/20200313154304.1636-4-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:43:28 +0000 (21:43 +0100)]
Merge tag 'renesas-arm64-dt-for-v5.7-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM64 DT updates for v5.7 (take two)
- Thermal support for R-Car M3-W+,
- Support for the M3ULCB board with R-Car M3-W+,
- CPUIdle support for R-Car M3-N and E3,
- Display support for the HiHope RZ/G2M board,
- A minor fix.
* tag 'renesas-arm64-dt-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display
arm64: dts: renesas: r8a77990: Add CPUIdle support for CA53 cores
arm64: dts: renesas: r8a77965: Add CPUIdle support for CA57 cores
arm64: dts: renesas: r8a77961: salvator-xs: Fix memory unit-address
arm64: dts: renesas: Add support for M3ULCB with R-Car M3-W+
arm64: dts: renesas: r8a77961: Add thermal nodes
Link: https://lore.kernel.org/r/20200313154304.1636-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:42:55 +0000 (21:42 +0100)]
Merge tag 'renesas-arm-dt-for-v5.7-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.7 (take two)
- LCD/touchscreen support for the iwg22d-sodimm board.
* tag 'renesas-arm-dt-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: iwg22d-sodimm: Enable touchscreen
ARM: dts: iwg22d-sodimm: Enable LCD panel
Link: https://lore.kernel.org/r/20200313154304.1636-2-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:42:02 +0000 (21:42 +0100)]
Merge tag 'sunxi-dt-for-5.7' of git://git./linux/kernel/git/sunxi/linux into arm/dt
Allwinner Device Tree Changes for v5.7
A fairly large set of changes for v5.7, including some new devices.
SoC specific changes:
- SPI on H6 SoC enabled
- Thermal sensor on R40 SoC enabled
- Deinterlace core hardware on A64 SoC enabled
- Redundant assigned-clocks properties removed
- required clock rates are now enforced by drivers
- LVDS panel support on A20 SoC enabled
- PMU compatible fixed for H5 and H6 SoCs
- Thermal trip points added for A83T and H5 SoCs
- (Image) Rotation core hardware on A83T and A64 SoCs enabled
Device specific changes:
- Pine64 PineTab and PinePhone added
- Various cleanups and improvements for Pine64 PineBook
- GPIO pin bank regulator supplies added for A64-OlinXino
- eMMC enabled on Orange Pi 3
- PocketBook Touch Lux 3 added
- Linutronix Testbox v2 added
- Ethernet enabled on Orange Pi One Plus
- HDMI enabled on H6-based Orange Pi boards
* tag 'sunxi-dt-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (46 commits)
arm64: dts: allwinner: a64: add node for rotation core
ARM: dts: sun8i: a83t: Add device node for rotation core
arm64: dts: allwinner: a64: Fix display clock register range
ARM: dts: sunxi: Fix DE2 clocks register range
arm64: dts: allwinner: h6: orangepi: Enable HDMI
arm64: dts: allwinner: h6: orangepi-one-plus: Enable ethernet
arm64: dts: allwinner: h6: Move ext. oscillator to board DTs
arm64: dts: allwinner: Add initial support for Pine64 PinePhone
dt-bindings: arm: sunxi: Add PinePhone 1.0 and 1.1 bindings
arm64: dts: sun50i-a64: Add i2c2 pins
ARM: dts: sunxi: h3/h5: add r_pwm node
arm64: allwinner: a64: enable LCD-related hardware for Pinebook
ARM: dts: sun8i-a83t: Add thermal trip points/cooling maps
ARM: dts: sun8i-h3: Add thermal trip points/cooling maps
arm64: dts: allwinner: h6: Fix PMU compatible
arm64: dts: allwinner: h5: Fix PMU compatible
ARM: dts: sun8i-a83t-tbs-a711: Drop superfluous dr_mode
arm64: dts: sun50i-h5-orange-pi-pc2: Add CPUX voltage regulator
ARM: dts: sun5i: Add PocketBook Touch Lux 3 support
dt-bindings: arm: sunxi: Add PocketBook Touch Lux 3
...
Link: https://lore.kernel.org/r/20200313055459.GA19820@wens.csie.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:41:31 +0000 (21:41 +0100)]
Merge tag 'arm-soc/for-5.7/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.7, please pull the following:
- Stefan adds GPIO labels to the Raspberry Pi 4 Model B board DTS
- Nicolas moves the eMMC2 controller into its separate node in order for
platform firmware to perform the necessary "dma-ranges" property
patching based on the chip revision since the eMMC controller has
different addressing constraints.
- Florian convers a whole bunch of Broadcom boards bindings from text to
YAML.
* tag 'arm-soc/for-5.7/devicetree' of https://github.com/Broadcom/stblinux:
dt-bindings: arm: Document Broadcom SoCs 'secondary-boot-reg'
dt-bindings: arm: bcm: Convert Vulcan to YAML
dt-bindings: arm: bcm: Convert BCM11351 to YAML
dt-bindings: arm: bcm: Convert BCM4708 to YAML
dt-bindings: arm: bcm: Convert BCM23550 to YAML
dt-bindings: arm: bcm: Convert BCM21664 to YAML
dt-bindings: arm: bcm: Convert Stingray to YAML
dt-bindings: arm: bcm: Convert Northstar 2 to YAML
dt-bindings: arm: bcm: Convert Northstar Plus to YAML
dt-bindings: arm: bcm: Convert Hurricane 2 to YAML
dt-bindings: arm: bcm: Convert Cygnus to YAML
ARM: dts: bcm2711: Move emmc2 into its own bus
ARM: dts: bcm2711-rpi-4-b: Add SoC GPIO labels
Link: https://lore.kernel.org/r/20200311212012.9418-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Chunyan Zhang [Wed, 11 Mar 2020 11:21:20 +0000 (19:21 +0800)]
arm64: dts: specify console via command line
The SPRD serial driver need to know which serial port would be used as
console in an early period during initialization, otherwise console
init would fail since we added this feature[1].
So this patch add console to command line via devicetree.
[1] https://lore.kernel.org/lkml/
20190826072929.7696-4-zhang.lyra@gmail.com/
Link: https://lore.kernel.org/r/20200311112120.30890-1-zhang.lyra@gmail.com
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:40:08 +0000 (21:40 +0100)]
Merge tag 'omap-for-v5.7/dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.7 merge window
Few device tree changes for omaps for v5.7 to configure omap5
AESS module and to add idle_states for am335x and am437x cpuidle.
* tag 'omap-for-v5.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: Add idle_states for cpuidle
ARM: dts: am33xx: Add idle_states for cpuidle
ARM: dts: Configure omap5 AESS
Link: https://lore.kernel.org/r/pull-1583511417-919838@atomide.com-4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:39:15 +0000 (21:39 +0100)]
Merge tag 'versatile-dts-v5.7-1' of git://git./linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS updates for the v5.7 series take one:
- Schema validation for the top level of all ARM reference
designs: Integrator, Versatile, RealView, Juno.
- Clean up some node names in the trees so they pass
validation fine.
- Drop the old text bindings.
- A top level DMA ranges patch from Rob.
* tag 'versatile-dts-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM/arm64: dts: Rename SMB bus to just bus
dt-bindings: arm: Drop the non-YAML bindings
dt-bindings: arm: Add Versatile Express and Juno YAML schema
dt-bindings: arm: Add RealView YAML schema
dt-bindings: arm: Add Versatile YAML schema
dt-bindings: arm: Add Integrator YAML schema
ARM: dts: RealView: Fix the name of the SoC node
ARM: dts: Versatile: Use syscon as node name for IB2
ARM: dts: integratorap: Remove top level dma-ranges
Link: https://lore.kernel.org/r/CACRpkdbbniYVnsE-pAmU2qCerswserNgEFtY48XQ+_K+DUNC9Q@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:24:43 +0000 (21:24 +0100)]
Merge tag 'renesas-arm64-dt-for-v5.7-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM64 DT updates for v5.7
- CryptoCell support for R-Car M3-W, M3-W+, M3-N, E3, and D3,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm64-dt-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: rzg2: Add reset control properties for display
arm64: dts: renesas: rcar-gen3: Add reset control properties for display
arm64: dts: renesas: Remove use of ARCH_R8A7795
arm64: dts: renesas: rcar-gen3: Add CCREE nodes
arm64: dts: renesas: rcar-gen3: Replace "vsps" by "renesas,vsps"
arm: dts: renesas: r8a77980: Remove r8a77970 DU compatible
Link: https://lore.kernel.org/r/20200226110221.19288-5-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 25 Mar 2020 20:20:18 +0000 (21:20 +0100)]
Merge tag 'renesas-arm-dt-for-v5.7-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.7
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: rzg1: Add reset control properties for display
ARM: dts: rcar-gen2: Add reset control properties for display
ARM: dts: r8a7745: Convert to new DU DT bindings
ARM: dts: r7s72100: Add SPIBSC clocks
ARM: dts: renesas: Group tuples in operating-points properties
ARM: dts: renesas: Add missing ethernet PHY reset GPIO on Gen2 reference boards
Link: https://lore.kernel.org/r/20200226110221.19288-2-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Vivek Unune [Tue, 17 Mar 2020 00:42:49 +0000 (01:42 +0100)]
arm64: dts: rockchip: Add Hugsun X99 power led
Remove pwm0 node as it interferes with power LED gpio.
Tested with LibreElec linux-next-
20200305
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Link: https://lore.kernel.org/r/20200313230513.123049-1-npcomplete13@gmail.com
[split out led addition into separate patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Vivek Unune [Fri, 13 Mar 2020 23:05:13 +0000 (19:05 -0400)]
arm64: dts: rockchip: Add Hugsun X99 IR receiver
Add the IR receiver and its associated pinctrl entry.
Tested with LibreElec linux-next-
20200305
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Link: https://lore.kernel.org/r/20200313230513.123049-1-npcomplete13@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 12 Mar 2020 17:14:41 +0000 (18:14 +0100)]
arm64: dts: rockchip: remove clock-names property from 'generic-ohci' nodes
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: usb@
ff5d0000:
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-names' is not a valid property name for usb_host nodes with
compatible string 'generic-ohci', so remove them.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/generic-ohci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312171441.21144-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 12 Mar 2020 17:14:40 +0000 (18:14 +0100)]
arm64: dts: rockchip: remove clock-names property from 'generic-ehci' nodes
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: usb@
ff5c0000:
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-names' is not a valid property name for usb_host nodes with
compatible string 'generic-ehci', so remove them.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/generic-ehci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312171441.21144-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 12 Mar 2020 17:22:39 +0000 (18:22 +0100)]
arm64: dts: rockchip: remove properties from spdif node RK3399 Excavator
An expermental test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dt.yaml:
spdif@
ff870000:
'i2c-scl-falling-time-ns', 'i2c-scl-rising-time-ns', 'power-domains'
do not match any of the regexes: 'pinctrl-[0-9]+'
'i2c-scl-falling-time-ns', 'i2c-scl-rising-time-ns'
are not valid properties for 'spdif' nodes, so remove them.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-spdif.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312172240.21362-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Wed, 11 Mar 2020 16:25:24 +0000 (17:25 +0100)]
ARM: dts: rockchip: remove #address-cells and #size-cells from i2s nodes
An experimental test with the command below gives
for example this error:
arch/arm/boot/dts/rk3036-evb.dt.yaml: i2s@
10220000:
'#address-cells', '#size-cells'
do not match any of the regexes: 'pinctrl-[0-9]+'
'#address-cells' and '#size-cells' are not a valid property
for i2s nodes, so remove them.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-i2s.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200311162524.19748-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Wed, 11 Mar 2020 16:25:23 +0000 (17:25 +0100)]
ARM: dts: rockchip: swap clocks and clock-names values for i2s nodes
Current dts files with 'i2s' nodes are manually verified.
In order to automate this process rockchip-i2s.txt
has to be converted to yaml. In the new setup dtbs_check with
rockchip-i2s.yaml expect clocks and clock-names values
in the same order. Fix this for some older Rockchip models.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-i2s.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200311162524.19748-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 12 Mar 2020 17:14:39 +0000 (18:14 +0100)]
ARM: dts: rockchip: remove clock-names property from 'generic-ohci' nodes
A test with the command below gives for example this error:
arch/arm/boot/dts/rv1108-evb.dt.yaml: usb@
30160000:
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-names' is not a valid property name for usb_host nodes with
compatible string 'generic-ohci', so remove them.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/generic-ohci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312171441.21144-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 12 Mar 2020 17:14:38 +0000 (18:14 +0100)]
ARM: dts: rockchip: remove clock-names property from 'generic-ehci' nodes
A test with the command below gives for example this error:
arch/arm/boot/dts/rv1108-evb.dt.yaml: usb@
30140000:
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-names' is not a valid property name for usb_host nodes with
compatible string 'generic-ehci', so remove them.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/generic-ehci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312171441.21144-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 12 Mar 2020 17:22:40 +0000 (18:22 +0100)]
ARM: dts: rockchip: swap clocks and clock-names values for spdif nodes
Current dts files with 'spdif' nodes are manually verified.
In order to automate this process rockchip-spdif.txt
has to be converted to yaml. In the new setup dtbs_check with
rockchip-spdif.yaml expect clocks and clock-names values
in the same order. Fix this for some older Rockchip models.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-spdif.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312172240.21362-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Joshua Watt [Wed, 19 Feb 2020 20:42:20 +0000 (14:42 -0600)]
ARM: dts: rockchip: Keep rk3288-tinker SD card IO powered during reboot
IO voltage regulator for the SD card must be kept on all the time,
otherwise when the board reboots the SD card can't be read by the
bootloader.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Link: https://lore.kernel.org/r/20200219204224.34154-1-JPEWhacker@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Fri, 13 Mar 2020 13:26:46 +0000 (14:26 +0100)]
ARM: dts: rockchip: remove clock-frequency from saradc node rv1108
An experimental test with the command below gives these errors:
arch/arm/boot/dts/rv1108-elgin-r1.dt.yaml: adc@
1038c000:
'clock-frequency'
does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm/boot/dts/rv1108-evb.dt.yaml: adc@
1038c000:
'clock-frequency'
does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-frequency' is not a valid property for a saradc node,
so remove it.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/iio/adc/
rockchip-saradc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200313132646.10317-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Sat, 14 Mar 2020 14:07:55 +0000 (15:07 +0100)]
ARM: dts: rockchip: fix vref-supply for &saradc node rk3288 firefly reload
A test with the command below gives this error:
arch/arm/boot/dts/rk3288-firefly-reload.dt.yaml: saradc@
ff100000:
'vref-supply' is a required property
PMIC Channel OUT11 with powername 'vcc_18'
(connected through R155 bridge with 'vccio_wl')
is used for the recovery key and ADC_AVDD_1V8.
Fix error by adding 'vcc_18' as vref for the saradc.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/iio/adc/
rockchip-saradc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200314140755.4877-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Katsuhiro Suzuki [Sun, 15 Mar 2020 09:51:15 +0000 (18:51 +0900)]
ARM: dts: rockchip: use DMA channels for UARTs for RK3288
This patch enables to use DMAC for all UARTs that are connected to
dmac_peri core for Rochchip RK3288.
Only uart2 is connected different DMAC (dmac_bus_s) so keep current
settings on this patch.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20200315095115.10106-1-katsuhiro@katsuster.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Mon, 16 Mar 2020 16:54:53 +0000 (17:54 +0100)]
ARM: dts: rockchip: rk3xxx: fix L2 cache-controller nodename
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3066a-bqcurie2.dt.yaml:
l2-cache-controller@
10138000: $nodename:0:
'l2-cache-controller@
10138000'
does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Fix error by changing nodename to 'cache-controller'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/l2c2x0.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200316165453.3022-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Mon, 16 Mar 2020 17:46:47 +0000 (18:46 +0100)]
ARM: dts: rockchip: fix lvds-encoder ports subnode for rk3188-bqedison2qc
A test with the command below gives this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: lvds-encoder:
'ports' is a required property
Fix error by adding a ports wrapper for port@0 and port@1
inside the 'lvds-encoder' node for rk3188-bqedison2qc.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/
bridge/lvds-codec.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200316174647.5598-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Christian Hewitt [Mon, 16 Mar 2020 03:20:54 +0000 (07:20 +0400)]
arm64: dts: meson: add thermal zones to meson gx devices
Adapt and update current VIM2 thermal zones support so that zones are
available on all meson GXBB/GXL/GXM devices - similar to changes made
for G12A/G12B/SM1 devices.
Suggested-by: Nick Xie <nick@khadas.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1584328854-28575-1-git-send-email-christianshewitt@gmail.com
Christian Hewitt [Thu, 5 Mar 2020 03:21:48 +0000 (07:21 +0400)]
arm64: dts: meson: khadas-vim3: move model to g12b-khadas-vim3 dtsi
The common meson-khadas-vim3.dtsi is now shared with VIM3L so move the
VIM3 model name to meson-g12b-khadas-vim3.dtsi.
meson-sm1-khadas-vim3l.dts contains the VIM3L model name.
changes in v2
- fix typo in commit message
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1583378508-14312-1-git-send-email-christianshewitt@gmail.com
Kunihiko Hayashi [Fri, 13 Mar 2020 00:58:15 +0000 (09:58 +0900)]
arm64: dts: uniphier: Set SCSSI clock and reset IDs for each channel
Currently common clock and reset IDs were used, however, each clock and
reset ID should be used for each channel.
Fixes:
925c5c32f31d ("arm64: dts: uniphier: add SPI node for LD20, LD11 and PXs3")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Kunihiko Hayashi [Fri, 13 Mar 2020 00:58:14 +0000 (09:58 +0900)]
ARM: dts: uniphier: Set SCSSI clock and reset IDs for each channel
Currently common clock and reset IDs were used, however, each clock and
reset ID should be used for each channel.
Pro5 and PXs2 are affected by this fix, but the SCSSI clock gate of Pro5 is
common to all channels.
Fixes:
92fa4f4cc2cd ("ARM: dts: uniphier: add SPI node for UniPhier 32bit SoCs")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Kunihiko Hayashi [Fri, 13 Mar 2020 00:58:11 +0000 (09:58 +0900)]
arm64: dts: uniphier: Add nodes of thermal monitor and thermal zone for PXs3
Add nodes of thermal monitor and thermal zone for UniPhier PXs3 SoC.
The thermal monitor node is included in sysctrl. This patch gives the
default value for PXs3 in the same way as LD20.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Kunihiko Hayashi [Fri, 13 Mar 2020 00:58:10 +0000 (09:58 +0900)]
arm64: dts: uniphier: Enable spi node for PXs3 reference board
PXs3 reference board has 2 spi connectors. This enables spi0 and spi1,
and adds aliases properties for each spi to determine device name
assignments.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Kunihiko Hayashi [Fri, 13 Mar 2020 00:58:09 +0000 (09:58 +0900)]
ARM: dts: uniphier: Add USB3 controller nodes for Pro5
Add USB3 controller nodes for Pro5 SoC and the boards.
Pro5 SoC has 2 controllers. USB0 includes 1 SS-PHY and 1 HS-PHY, and USB1
includes 1 SS-PHY and 2 HS-PHY.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Michael Walle [Thu, 12 Mar 2020 16:43:20 +0000 (17:43 +0100)]
arm64: dts: ls1028a: disable the felix switch by default
Disable the felix switch by default and enable it per board which are
actually using it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Thu, 12 Mar 2020 07:34:10 +0000 (15:34 +0800)]
arm64: dts: imx8mp: Add snvs clock to powerkey
SNVS powerkey driver needs snvs clock for proper clock management,
add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Thu, 12 Mar 2020 07:34:09 +0000 (15:34 +0800)]
arm64: dts: imx8mn: Add snvs clock to powerkey
SNVS powerkey driver needs snvs clock for proper clock management,
add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Xiaowei Bao [Wed, 11 Mar 2020 10:03:39 +0000 (18:03 +0800)]
arm64: dts: ls1028a: Add PCIe controller DT nodes
LS1028a implements 2 PCIe 3.0 controllers.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Wed, 11 Mar 2020 07:49:29 +0000 (08:49 +0100)]
arm64: dts: ls1028a: sl28: add support for variant 2
Now that there is support for the Felix switch this variant can also be
added. It features two external ports ethernet ports which are connected
to the internal switch core. No direct connection to any of the enetc's
is supported.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Wed, 11 Mar 2020 07:49:28 +0000 (08:49 +0100)]
arm64: dts: ls1028a: sl28: expose switch ports in KBox A-230-LS
The KBox A-230-LS supports four external ports which are connected to
the internal switch of the LS1028A via QSGMII. Now that the Felix switch
is supported, add these ports in the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Wed, 11 Mar 2020 07:49:27 +0000 (08:49 +0100)]
arm64: dts: ls1028a: sl28: fix on-board EEPROMS
The module itself has another EEPROM at 50h on I2C4. The EEPROM on the
carriers is located at 57h on I2C3. Fix that in the device trees.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Wed, 11 Mar 2020 07:49:26 +0000 (08:49 +0100)]
arm64: dts: freescale: sl28: add SPI flash
There is a SPI flash on this carrier connected to the third DSPI
controller. Add it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Wed, 11 Mar 2020 07:17:56 +0000 (15:17 +0800)]
arm64: dts: imx8m: fix aips dts node
Per binding doc fsl,aips-bus.yaml, compatible and reg is
required. And for reg, the AIPS configuration space should be
used, not all the AIPS bus space.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Fri, 13 Mar 2020 10:25:34 +0000 (11:25 +0100)]
ARM: dts: imx6q-marsboard: properly define rgmii PHY
The Atheros AR8035 PHY can be autodetected but can't use interrupt
support provided on this board. Define MDIO bus and the PHY node to make
it work properly.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Fri, 13 Mar 2020 10:25:33 +0000 (11:25 +0100)]
ARM: dts: imx6dl-riotboard: properly define rgmii PHY
The Atheros AR8035 PHY can be autodetected but can't use interrupt
support provided on this board. Define MDIO bus and the PHY node to make
it work properly.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Fri, 13 Mar 2020 09:58:29 +0000 (10:58 +0100)]
ARM: dts: imx51-zii-rdu1: set name prefix for TPA6130A2
Set a sound name prefix for the HPA, as otherwise the sound controls
naming will clash with the controls of the DAC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Fri, 13 Mar 2020 09:58:04 +0000 (10:58 +0100)]
ARM: dts: imx6: RDU2: assign video PLL as input to LDB
Currently we don't ensure that the LDB is clocked from the video PLL
and relied on the bootloader to do the correct setup. This isn't always
true, in which case we would run with a vastly different video clock
than the desired one. Fix this by assigning the proper parent to the
LDB.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Igor Opaniuk [Thu, 12 Mar 2020 08:38:30 +0000 (10:38 +0200)]
ARM: dts: vf: toradex: SPDX tags and copyright cleanup
1. Replace boiler plate licenses texts with the SPDX license
identifiers in Toradex Vybrid-based SoM device trees.
2. As X11 is identical to the MIT License, but with an extra sentence
that prohibits using the copyright holders' names for advertising or
promotional purposes without written permission, use MIT license instead
of X11 ('s/X11/MIT/g').
3. Replace "Toradex AG" with "Toradex" in the Copyright notice.
4. Use GPL2.0+ instead of GPL2.0, as it's used now by default for all
new DTS files.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Igor Opaniuk [Thu, 12 Mar 2020 08:38:29 +0000 (10:38 +0200)]
ARM: dts: imx7: toradex: use SPDX-License-Identifier
1. Replace boiler plate licenses texts with the SPDX license
identifiers in Toradex i.MX7-based SoM device trees.
2. As X11 is identical to the MIT License, but with an extra sentence
that prohibits using the copyright holders' names for advertising or
promotional purposes without written permission, use MIT license instead
of X11 ('s/X11/MIT/g').
3. Replace "Toradex AG" with "Toradex" in the Copyright notice.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Igor Opaniuk [Thu, 12 Mar 2020 08:38:28 +0000 (10:38 +0200)]
ARM: dts: imx6: toradex: use SPDX-License-Identifier
1. Replace boiler plate licenses texts with the SPDX license
identifiers in Toradex iMX6-based SoM device trees.
2. As X11 is identical to the MIT License, but with an extra sentence
that prohibits using the copyright holders' names for advertising or
promotional purposes without written permission, use MIT license instead
of X11 ('s/X11/MIT/g').
3. Replace "Toradex AG" with "Toradex" in the Copyright notice.
4. Use GPL2.0+ instead of GPL2.0, as it's used now by default for all
new DTS files from Toradex.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Philipp Zabel [Fri, 13 Mar 2020 10:57:39 +0000 (11:57 +0100)]
ARM: dts: imx51: add capture-subsystem device
Add IPU CSI ports and capture-subsystem device so the capture subsystem
part of the IPUv3EX can be used with the staging imx-media driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Wed, 11 Mar 2020 09:02:06 +0000 (17:02 +0800)]
ARM: dts: imx: add nvmem property for cpu0
Add nvmem related property for cpu0, then nvmem API could be used
to read cpu speed grading to avoid directly read OCOTP registers
mapped which could not handle defer probe.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Mar 2020 18:08:25 +0000 (15:08 -0300)]
ARM: dts: imx6qdl: Add imx6qdl-pico support
Add support for all the imx6qdl-pico variants.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Mar 2020 18:08:24 +0000 (15:08 -0300)]
ARM: dts: imx6ul-pico: Add support for the dwarf baseboard
Add support for the imx6ul pico board with dwarf baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Mar 2020 18:08:23 +0000 (15:08 -0300)]
ARM: dts: imx7d-pico: Add support for the nymph baseboard
Add support for the imx7d pico board with nymph baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Mar 2020 18:08:22 +0000 (15:08 -0300)]
ARM: dts: imx7d-pico: Add support for the dwarf baseboard
Add support for the imx7d pico board with dwarf baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 10 Mar 2020 18:08:21 +0000 (15:08 -0300)]
dt-bindings: arm: fsl: Add TechNexion boards
Add entries for the TechNexion boards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Heimpold [Sun, 8 Mar 2020 22:21:44 +0000 (23:21 +0100)]
ARM: dts: imx23: introduce mmc0_sck_cfg
The Olimex Olinuxino board has a user led connected to SSP1_DETECT.
But since this pin is listed in mmc0_pins_fixup, it is already claimed
by MMC driver and this results in this error during boot:
[ 1.390000] imx23-pinctrl
80018000.pinctrl: pin SSP1_DETECT already
requested by
80010000.spi; cannot claim for leds
[ 1.400000] imx23-pinctrl
80018000.pinctrl: pin-65 (leds) status -22
[ 1.410000] imx23-pinctrl
80018000.pinctrl: could not request pin 65
(SSP1_DETECT) from group led_gpio2_1.0 on device
80018000.pinctrl
[ 1.420000] leds-gpio leds: Error applying setting, reverse things back
[ 1.430000] leds-gpio: probe of leds failed with error -22
This fix it, introduce mmc0_sck_cfg and switch the Olinuxino board to it.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Sun, 8 Mar 2020 06:58:41 +0000 (14:58 +0800)]
arm64: dts: imx8mn: Add CPU thermal zone support
i.MX8MN shares same thermal sensor with i.MX8MM, add thermal zone
support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Amit Kucheria [Thu, 5 Mar 2020 22:00:15 +0000 (03:30 +0530)]
arm64: dts: marvell: Fix cpu compatible for AP807-quad
make -k ARCH=arm64 dtbs_check shows the following errors. Fix them by
removing the "arm,armv8" compatible.
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long CHECK
arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex.dt.yaml
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Vadym Kochan [Sun, 9 Feb 2020 21:20:30 +0000 (21:20 +0000)]
arm64: dts: marvell: fix non-existed cpu referrence in armada-ap806-dual.dtsi
armada-ap806-dual.dtsi includes armada-ap806.dtsi which describes
thermal zones for 4 cpus but only cpu0 and cpu1 only exists for dual
configuration, this makes dtb compilation fail. Fix it by removing
thermal zone nodes for non-existed cpus for dual configuration.
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tomasz Maciej Nowak [Thu, 27 Feb 2020 16:48:42 +0000 (17:48 +0100)]
arm64: dts: marvell: build ESPRESSObin variants
The commit adding ESPRESSObin variants didn't include those in Makefile to
be built.
Fixes:
447b8789359f ("arm64: dts: marvell: add ESPRESSObin variants")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tomasz Maciej Nowak [Thu, 27 Feb 2020 16:48:41 +0000 (17:48 +0100)]
arm64: dts: marvell: espressobin: indicate dts version
The commit introducing ESPRESSObin variants didn't specify dts version,
and because of that they are treated by dtc as legacy ones. Fix that by
properly specifying version in each dts.
Fixes:
447b8789359f ("arm64: dts: marvell: add ESPRESSObin variants")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tomasz Maciej Nowak [Thu, 27 Feb 2020 16:52:32 +0000 (17:52 +0100)]
arm64: dts: marvell: espressobin: add ethernet alias
The maker of this board and its variants, stores MAC address in U-Boot
environment. Add alias for bootloader to recognise, to which ethernet
node inject the factory MAC address.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Russell King [Thu, 27 Feb 2020 12:08:58 +0000 (12:08 +0000)]
arm64: dts: mcbin: support 2W SFP modules
Allow the SFP cages to be used with 2W SFP modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Russell King [Tue, 25 Feb 2020 11:45:12 +0000 (11:45 +0000)]
arm64: dts: clearfog-gt-8k: set gigabit PHY reset deassert delay
If the mv88e6xxx DSA driver is built as a module, it causes the
ethernet driver to re-probe when it's loaded. This in turn causes
the gigabit PHY to be momentarily reset and reprogrammed. However,
we attempt to reprogram the PHY immediately after deasserting reset,
and the PHY ignores the writes.
This results in the PHY operating in the wrong mode, and the copper
link states down.
Set a reset deassert delay of 10ms for the gigabit PHY to avoid this.
Fixes:
babc5544c293 ("arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Yann Gautier [Wed, 4 Mar 2020 08:09:56 +0000 (09:09 +0100)]
ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
On those boards, as stated in schematics files, the regulator used for IOs
is VDD. It was wrongly set to v3v3.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Yann Gautier [Wed, 4 Mar 2020 08:09:55 +0000 (09:09 +0100)]
ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
On STM32MP1 DK1, DK2, ED1 and EV1 boards, there is only a micro SD socket.
This is also the case on Avenger board.
They don't support the Write Protect pin.
The disable-wp is then added in the SD-cards sdmmc1 nodes.
This avoids executing some code and a warning during driver probe.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Yann Gautier [Wed, 4 Mar 2020 08:09:54 +0000 (09:09 +0100)]
ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
The broken-cd properties are replaced with cd-gpios, with the correct
GPIO to detect the card insertion. The GPIO lines require a pull-up.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Benjamin Gaignard [Fri, 28 Feb 2020 12:52:04 +0000 (13:52 +0100)]
ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
Remove unused properties from stpmic node.
The issues have been detected by running dtbs_check.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Benjamin Gaignard [Fri, 28 Feb 2020 12:52:05 +0000 (13:52 +0100)]
ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
Rename stmfx joystick pins names according to yaml description.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Ahmad Fatoum [Mon, 24 Feb 2020 17:20:30 +0000 (18:20 +0100)]
ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
All of the STM32MP151[1], STM32MP153[2] and STM32MP157[3] have their
Cortex-A7 cores running at 650 MHz.
Add the clock-frequency property to CPU nodes to avoid warnings about
them missing.
[1]: https://www.st.com/en/microcontrollers-microprocessors/stm32mp151.html
[2]: https://www.st.com/en/microcontrollers-microprocessors/stm32mp153.html
[3]: https://www.st.com/en/microcontrollers-microprocessors/stm32mp157.html
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Alain Volmat [Mon, 6 Jan 2020 13:28:34 +0000 (14:28 +0100)]
ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
Add the wakeup-source property in all i2c nodes of
the SoC stm32mp157c so that those I2C controllers can become
wakeup-source.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Alain Volmat [Mon, 6 Jan 2020 13:28:31 +0000 (14:28 +0100)]
ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
Add the sleep state pinctrl entry for the i2c4 node
of the stm32mp157c-ed1 board.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Linus Walleij [Sat, 7 Mar 2020 19:36:27 +0000 (20:36 +0100)]
ARM: dts: Add devicetree for Samsung GT-S7710
The Samsung GT-S7710 also known as XCover 2 or Skomer is a
Ux500-based mobile phone. In the source code release from
Samsung's open source site it is referred to as "Skomer".
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200307193627.4092-1-linus.walleij@linaro.org
[Typographic fixups when applying]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alain Volmat [Mon, 6 Jan 2020 13:28:30 +0000 (14:28 +0100)]
ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
Add the sleep state pinctrl entry for the i2c2 and i2c5 nodes
of the stm32mp157c-ev1 board.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Alain Volmat [Mon, 6 Jan 2020 13:28:29 +0000 (14:28 +0100)]
ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
Add the sleep state pinctrl entry for the i2c4 node
of the stm32mp15xx-dkx.dtsi
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Alain Volmat [Fri, 13 Mar 2020 11:57:36 +0000 (12:57 +0100)]
ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
On DK boards, all I2C4 bus slaves supports I2C Fast Mode hence setting
the bus frequency to 400 KHz.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Alain Volmat [Fri, 13 Mar 2020 11:46:29 +0000 (12:46 +0100)]
ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
On this board, the I2C4 bus has only a single slave (pmic) which
supports I2C Fast Mode hence setting bus frequency to 400 KHz.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Sowjanya Komatineni [Tue, 14 Jan 2020 07:24:20 +0000 (23:24 -0800)]
ARM: tegra: Update sound node clocks in device tree
clk_out_1, clk_out_2, and clk_out_3 are part of Tegra PMC block but were
previously erroneously provided by the clock and reset controller.
clk_out_1 is dedicated for audio mclk on Tegra30 through Tegra210.
This patch updates device tree sound node to use clk_out_1 from the PMC
provider as mclk and uses assigned-clock properties to specify clock
parents for clk_out_1 and extern1.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sowjanya Komatineni [Tue, 14 Jan 2020 07:24:18 +0000 (23:24 -0800)]
ARM: tegra: Add clock-cells property to PMC
Tegra PMC has clk_out_1, clk_out_2, clk_out_3, and blink clock.
These clocks were erroneously provided by the clock and reset controller
and are now provided by the PMC instead because that's where the primary
controls are.
This patch adds #clock-cells property with 1 clock specifier to the
Tegra PMC node in device tree.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nagarjuna Kristam [Mon, 10 Feb 2020 08:11:45 +0000 (13:41 +0530)]
ARM: tegra: Remove USB 2-0 port from Jetson TK1 padctl
On Jetson TK1 USB 2-0 port is controlled by phy-tegra-usb driver
rather than padctl driver. Remove the entry for the same.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Fri, 13 Mar 2020 10:25:32 +0000 (11:25 +0100)]
Merge branch 'for-5.7/dt-bindings' into for-5.7/arm/dt
Nagarjuna Kristam [Mon, 10 Feb 2020 08:11:28 +0000 (13:41 +0530)]
dt-bindings: usb: Add NVIDIA Tegra XUSB device mode controller binding
Add device-tree binding documentation for the XUSB device mode controller
present on Tegra210 and Tegra186 SoC. This controller supports the USB 3.0
specification.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nagarjuna Kristam [Mon, 10 Feb 2020 08:11:27 +0000 (13:41 +0530)]
dt-bindings: phy: tegra-xusb: Add usb-role-switch
Add usb-role-switch property for Tegra210 and Tegra186 platforms. This
entry is used by XUSB pad controller driver to register for role changes
for OTG/Peripheral capable USB 2 ports.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
JC Kuo [Wed, 12 Feb 2020 06:11:31 +0000 (14:11 +0800)]
dt-bindings: phy: tegra: Add Tegra194 support
Extend the bindings to cover the set of features found in Tegra194.
Note that, technically, there are four more supplies connected to the
XUSB pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL)
, but the power sequencing requirements of Tegra194 require these to be
under the control of the PMIC.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>