OSDN Git Service
Jonathan McDowell [Thu, 21 May 2020 11:49:34 +0000 (12:49 +0100)]
net: ethernet: stmmac: Enable interface clocks on probe for IPQ806x
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
[ 59.028131] ipq806x-gmac-dwmac
37600000.ethernet: Failed to reset the dma
[ 59.028196] ipq806x-gmac-dwmac
37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[ 59.034056] ipq806x-gmac-dwmac
37600000.ethernet eth1: stmmac_open: Hw setup failed
This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:
https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 May 2020 23:05:42 +0000 (16:05 -0700)]
Merge branch 'netdevsim-Two-small-fixes'
Ido Schimmel says:
====================
netdevsim: Two small fixes
Fix two bugs observed while analyzing regression failures.
Patch #1 fixes a bug where sometimes the drop counter of a packet trap
policer would not increase.
Patch #2 adds a missing initialization of a variable in a related
selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 21 May 2020 11:46:17 +0000 (14:46 +0300)]
selftests: netdevsim: Always initialize 'RET' variable
The variable is used by log_test() to check if the test case completely
successfully or not. In case it is not initialized at the start of a
test case, it is possible for the test case to fail despite not
encountering any errors.
Example:
```
...
TEST: Trap group statistics [ OK ]
TEST: Trap policer [FAIL]
Policer drop counter was not incremented
TEST: Trap policer binding [FAIL]
Policer drop counter was not incremented
```
Failure of trap_policer_test() caused trap_policer_bind_test() to fail
as well.
Fix by adding missing initialization of the variable.
Fixes:
5fbff58e27a1 ("selftests: netdevsim: Add test cases for devlink-trap policers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 21 May 2020 11:46:16 +0000 (14:46 +0300)]
netdevsim: Ensure policer drop counter always increases
In case the policer drop counter is retrieved when the jiffies value is
a multiple of 64, the counter will not be incremented.
This randomly breaks a selftest [1] the reads the counter twice and
checks that it was incremented:
```
TEST: Trap policer [FAIL]
Policer drop counter was not incremented
```
Fix by always incrementing the counter by 1.
[1] tools/testing/selftests/drivers/net/netdevsim/devlink_trap.sh
Fixes:
ad188458d012 ("netdevsim: Add devlink-trap policer support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 May 2020 22:53:30 +0000 (15:53 -0700)]
Merge tag 'rxrpc-fixes-
20200520' of git://git./linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix retransmission timeout and ACK discard
Here are a couple of fixes and an extra tracepoint for AF_RXRPC:
(1) Calculate the RTO pretty much as TCP does, rather than making
something up, including an initial 4s timeout (which causes return
probes from the fileserver to fail if a packet goes missing), and add
backoff.
(2) Fix the discarding of out-of-order received ACKs. We mustn't let the
hard-ACK point regress, nor do we want to do unnecessary
retransmission because the soft-ACK list regresses. This is not
trivial, however, due to some loose wording in various old protocol
specs, the ACK field that should be used for this sometimes has the
wrong information in it.
(3) Add a tracepoint to log a discarded ACK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Valentin Longchamp [Wed, 20 May 2020 15:53:50 +0000 (17:53 +0200)]
net/ethernet/freescale: rework quiesce/activate for ucc_geth
ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.
The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].
A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.
The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.
[1] https://lists.openwall.net/netdev/2020/01/08/201
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Matteo Ghidoni <matteo.ghidoni@ch.abb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jere Leppänen [Wed, 20 May 2020 15:15:31 +0000 (18:15 +0300)]
sctp: Start shutdown on association restart if in SHUTDOWN-SENT state and socket is closed
Commit
bdf6fa52f01b ("sctp: handle association restarts when the
socket is closed.") starts shutdown when an association is restarted,
if in SHUTDOWN-PENDING state and the socket is closed. However, the
rationale stated in that commit applies also when in SHUTDOWN-SENT
state - we don't want to move an association to ESTABLISHED state when
the socket has been closed, because that results in an association
that is unreachable from user space.
The problem scenario:
1. Client crashes and/or restarts.
2. Server (using one-to-one socket) calls close(). SHUTDOWN is lost.
3. Client reconnects using the same addresses and ports.
4. Server's association is restarted. The association and the socket
move to ESTABLISHED state, even though the server process has
closed its descriptor.
Also, after step 4 when the server process exits, some resources are
leaked in an attempt to release the underlying inet sock structure in
ESTABLISHED state:
IPv4: Attempt to release TCP socket in state 1
00000000377288c7
Fix by acting the same way as in SHUTDOWN-PENDING state. That is, if
an association is restarted in SHUTDOWN-SENT state and the socket is
closed, then start shutdown and don't move the association or the
socket to ESTABLISHED state.
Fixes:
bdf6fa52f01b ("sctp: handle association restarts when the socket is closed.")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 21 May 2020 18:29:58 +0000 (11:29 -0700)]
tipc: block BH before using dst_cache
dst_cache_get() documents it must be used with BH disabled.
sysbot reported :
BUG: using smp_processor_id() in preemptible [
00000000] code: /21697
caller is dst_cache_get+0x3a/0xb0 net/core/dst_cache.c:68
CPU: 0 PID: 21697 Comm: Not tainted 5.7.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x188/0x20d lib/dump_stack.c:118
check_preemption_disabled lib/smp_processor_id.c:47 [inline]
debug_smp_processor_id.cold+0x88/0x9b lib/smp_processor_id.c:57
dst_cache_get+0x3a/0xb0 net/core/dst_cache.c:68
tipc_udp_xmit.isra.0+0xb9/0xad0 net/tipc/udp_media.c:164
tipc_udp_send_msg+0x3e6/0x490 net/tipc/udp_media.c:244
tipc_bearer_xmit_skb+0x1de/0x3f0 net/tipc/bearer.c:526
tipc_enable_bearer+0xb2f/0xd60 net/tipc/bearer.c:331
__tipc_nl_bearer_enable+0x2bf/0x390 net/tipc/bearer.c:995
tipc_nl_bearer_enable+0x1e/0x30 net/tipc/bearer.c:1003
genl_family_rcv_msg_doit net/netlink/genetlink.c:673 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:718 [inline]
genl_rcv_msg+0x627/0xdf0 net/netlink/genetlink.c:735
netlink_rcv_skb+0x15a/0x410 net/netlink/af_netlink.c:2469
genl_rcv+0x24/0x40 net/netlink/genetlink.c:746
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
netlink_unicast+0x537/0x740 net/netlink/af_netlink.c:1329
netlink_sendmsg+0x882/0xe10 net/netlink/af_netlink.c:1918
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x6bf/0x7e0 net/socket.c:2362
___sys_sendmsg+0x100/0x170 net/socket.c:2416
__sys_sendmsg+0xec/0x1b0 net/socket.c:2449
do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295
entry_SYSCALL_64_after_hwframe+0x49/0xb3
RIP: 0033:0x45ca29
Fixes:
e9c1a793210f ("tipc: add dst_cache support for udp media")
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 20 May 2020 11:26:35 +0000 (12:26 +0100)]
net: mvpp2: fix RX hashing for non-10G ports
When rxhash is enabled on any ethernet port except the first in each CP
block, traffic flow is prevented. The analysis is below:
I've been investigating this afternoon, and what I've found, comparing
a kernel without
895586d5dc32 and with
895586d5dc32 applied is:
- The table programmed into the hardware via mvpp22_rss_fill_table()
appears to be identical with or without the commit.
- When rxhash is enabled on eth2, mvpp2_rss_port_c2_enable() reports
that c2.attr[0] and c2.attr[2] are written back containing:
- with
895586d5dc32, failing:
00200000 40000000
- without
895586d5dc32, working:
04000000 40000000
- When disabling rxhash, c2.attr[0] and c2.attr[2] are written back as:
04000000 00000000
The second value represents the MVPP22_CLS_C2_ATTR2_RSS_EN bit, the
first value is the queue number, which comprises two fields. The high
5 bits are 24:29 and the low three are 21:23 inclusive. This comes
from:
c2.attr[0] = MVPP22_CLS_C2_ATTR0_QHIGH(qh) |
MVPP22_CLS_C2_ATTR0_QLOW(ql);
So, the working case gives eth2 a queue id of 4.0, or 32 as per
port->first_rxq, and the non-working case a queue id of 0.1, or 1.
The allocation of queue IDs seems to be in mvpp2_port_probe():
if (priv->hw_version == MVPP21)
port->first_rxq = port->id * port->nrxqs;
else
port->first_rxq = port->id * priv->max_port_rxqs;
Where:
if (priv->hw_version == MVPP21)
priv->max_port_rxqs = 8;
else
priv->max_port_rxqs = 32;
Making the port 0 (eth0 / eth1) have port->first_rxq = 0, and port 1
(eth2) be 32. It seems the idea is that the first 32 queues belong to
port 0, the second 32 queues belong to port 1, etc.
mvpp2_rss_port_c2_enable() gets the queue number from it's parameter,
'ctx', which comes from mvpp22_rss_ctx(port, 0). This returns
port->rss_ctx[0].
mvpp22_rss_context_create() is responsible for allocating that, which
it does by looking for an unallocated priv->rss_tables[] pointer. This
table is shared amongst all ports on the CP silicon.
When we write the tables in mvpp22_rss_fill_table(), the RSS table
entry is defined by:
u32 sel = MVPP22_RSS_INDEX_TABLE(rss_ctx) |
MVPP22_RSS_INDEX_TABLE_ENTRY(i);
where rss_ctx is the context ID (queue number) and i is the index in
the table.
If we look at what is written:
- The first table to be written has "sel" values of
00000000..
0000001f,
containing values 0..3. This appears to be for eth1. This is table 0,
RX queue number 0.
- The second table has "sel" values of
00000100..
0000011f, and appears
to be for eth2. These contain values 0x20..0x23. This is table 1,
RX queue number 0.
- The third table has "sel" values of
00000200..
0000021f, and appears
to be for eth3. These contain values 0x40..0x43. This is table 2,
RX queue number 0.
How do queue numbers translate to the RSS table? There is another
table - the RXQ2RSS table, indexed by the MVPP22_RSS_INDEX_QUEUE field
of MVPP22_RSS_INDEX and accessed through the MVPP22_RXQ2RSS_TABLE
register. Before
895586d5dc32, it was:
mvpp2_write(priv, MVPP22_RSS_INDEX,
MVPP22_RSS_INDEX_QUEUE(port->first_rxq));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE,
MVPP22_RSS_TABLE_POINTER(port->id));
and after:
mvpp2_write(priv, MVPP22_RSS_INDEX, MVPP22_RSS_INDEX_QUEUE(ctx));
mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE, MVPP22_RSS_TABLE_POINTER(ctx));
Before the commit, for eth2, that would've contained '32' for the
index and '1' for the table pointer - mapping queue 32 to table 1.
Remember that this is queue-high.queue-low of 4.0.
After the commit, we appear to map queue 1 to table 1. That again
looks fine on the face of it.
Section 9.3.1 of the A8040 manual seems indicate the reason that the
queue number is separated. queue-low seems to always come from the
classifier, whereas queue-high can be from the ingress physical port
number or the classifier depending on the MVPP2_CLS_SWFWD_PCTRL_REG.
We set the port bit in MVPP2_CLS_SWFWD_PCTRL_REG, meaning that queue-high
comes from the MVPP2_CLS_SWFWD_P2HQ_REG() register... and this seems to
be where our bug comes from.
mvpp2_cls_oversize_rxq_set() sets this up as:
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_P2HQ_REG(port->id),
(port->first_rxq >> MVPP2_CLS_OVERSIZE_RXQ_LOW_BITS));
val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG);
val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id);
mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val);
Setting the MVPP2_CLS_SWFWD_PCTRL_MASK bit means that the queue-high
for eth2 is _always_ 4, so only queues 32 through 39 inclusive are
available to eth2. Yet, we're trying to tell the classifier to set
queue-high, which will be ignored, to zero. Hence, the queue-high
field (MVPP22_CLS_C2_ATTR0_QHIGH()) from the classifier will be
ignored.
This means we end up directing traffic from eth2 not to queue 1, but
to queue 33, and then we tell it to look up queue 33 in the RSS table.
However, RSS table has not been programmed for queue 33, and so it ends
up (presumably) dropping the packets.
It seems that mvpp22_rss_context_create() doesn't take account of the
fact that the upper 5 bits of the queue ID can't actually be changed
due to the settings in mvpp2_cls_oversize_rxq_set(), _or_ it seems that
mvpp2_cls_oversize_rxq_set() has been missed in this commit. Either
way, these two functions mutually disagree with what queue number
should be used.
Looking deeper into what mvpp2_cls_oversize_rxq_set() and the MTU
validation is doing, it seems that MVPP2_CLS_SWFWD_P2HQ_REG() is used
for over-sized packets attempting to egress through this port. With
the classifier having had RSS enabled and directing eth2 traffic to
queue 1, we may still have packets appearing on queue 32 for this port.
However, the only way we may end up with over-sized packets attempting
to egress through eth2 - is if the A8040 forwards frames between its
ports. From what I can see, we don't support that feature, and the
kernel restricts the egress packet size to the MTU. In any case, if we
were to attempt to transmit an oversized packet, we have no support in
the kernel to deal with that appearing in the port's receive queue.
So, this patch attempts to solve the issue by clearing the
MVPP2_CLS_SWFWD_PCTRL_MASK() bit, allowing MVPP22_CLS_C2_ATTR0_QHIGH()
from the classifier to define the queue-high field of the queue number.
My testing seems to confirm my findings above - clearing this bit
means that if I enable rxhash on eth2, the interface can then pass
traffic, as we are now directing traffic to RX queue 1 rather than
queue 33. Traffic still seems to work with rxhash off as well.
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Fixes:
895586d5dc32 ("net: mvpp2: cls: Use RSS contexts to handle RSS tables")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 May 2020 21:35:35 +0000 (14:35 -0700)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2020-05-22
The following pull-request contains BPF updates for your *net* tree.
We've added 3 non-merge commits during the last 3 day(s) which contain
a total of 5 files changed, 69 insertions(+), 11 deletions(-).
The main changes are:
1) Fix to reject mmap()'ing read-only array maps as writable since BPF verifier
relies on such map content to be frozen, from Andrii Nakryiko.
2) Fix breaking audit from secid_to_secctx() LSM hook by avoiding to use
call_int_hook() since this hook is not stackable, from KP Singh.
3) Fix BPF flow dissector program ref leak on netns cleanup, from Jakub Sitnicki.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Fri, 22 May 2020 08:54:34 +0000 (11:54 +0300)]
felix: Fix initialization of ioremap resources
The caller of devm_ioremap_resource(), either accidentally
or by wrong assumption, is writing back derived resource data
to global static resource initialization tables that should
have been constant. Meaning that after it computes the final
physical start address it saves the address for no reason
in the static tables. This doesn't affect the first driver
probing after reboot, but it breaks consecutive driver reloads
(i.e. driver unbind & bind) because the initialization tables
no longer have the correct initial values. So the next probe()
will map the device registers to wrong physical addresses,
causing ARM SError async exceptions.
This patch fixes all of the above.
Fixes:
56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Todd Malsbary [Fri, 22 May 2020 02:10:49 +0000 (19:10 -0700)]
mptcp: use untruncated hash in ADD_ADDR HMAC
There is some ambiguity in the RFC as to whether the ADD_ADDR HMAC is
the rightmost 64 bits of the entire hash or of the leftmost 160 bits
of the hash. The intention, as clarified with the author of the RFC,
is the entire hash.
This change returns the entire hash from
mptcp_crypto_hmac_sha (instead of only the first 160 bits), and moves
any truncation/selection operation on the hash to the caller.
Fixes:
12555a2d97e5 ("mptcp: use rightmost 64 bits in ADD_ADDR HMAC")
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Todd Malsbary <todd.malsbary@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Sitnicki [Thu, 21 May 2020 08:34:35 +0000 (10:34 +0200)]
flow_dissector: Drop BPF flow dissector prog ref on netns cleanup
When attaching a flow dissector program to a network namespace with
bpf(BPF_PROG_ATTACH, ...) we grab a reference to bpf_prog.
If netns gets destroyed while a flow dissector is still attached, and there
are no other references to the prog, we leak the reference and the program
remains loaded.
Leak can be reproduced by running flow dissector tests from selftests/bpf:
# bpftool prog list
# ./test_flow_dissector.sh
...
selftests: test_flow_dissector [PASS]
# bpftool prog list
4: flow_dissector name _dissect tag
e314084d332a5338 gpl
loaded_at 2020-05-20T18:50:53+0200 uid 0
xlated 552B jited 355B memlock 4096B map_ids 3,4
btf_id 4
#
Fix it by detaching the flow dissector program when netns is going away.
Fixes:
d58e468b1112 ("flow_dissector: implements flow dissector BPF hook")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20200521083435.560256-1-jakub@cloudflare.com
Tang Bin [Wed, 20 May 2020 09:55:32 +0000 (17:55 +0800)]
net: sgi: ioc3-eth: Fix return value check in ioc3eth_probe()
In the function devm_platform_ioremap_resource(), if get resource
failed, the return value is ERR_PTR() not NULL. Thus it must be
replaced by IS_ERR(), or else it may result in crashes if a critical
error path is encountered.
Fixes:
0ce5ebd24d25 ("mfd: ioc3: Add driver for SGI IOC3 chip")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Wed, 20 May 2020 09:15:46 +0000 (11:15 +0200)]
net: don't return invalid table id error when we fall back to PF_UNSPEC
In case we can't find a ->dumpit callback for the requested
(family,type) pair, we fall back to (PF_UNSPEC,type). In effect, we're
in the same situation as if userspace had requested a PF_UNSPEC
dump. For RTM_GETROUTE, that handler is rtnl_dump_all, which calls all
the registered RTM_GETROUTE handlers.
The requested table id may or may not exist for all of those
families. commit
ae677bbb4441 ("net: Don't return invalid table id
error when dumping all families") fixed the problem when userspace
explicitly requests a PF_UNSPEC dump, but missed the fallback case.
For example, when we pass ipv6.disable=1 to a kernel with
CONFIG_IP_MROUTE=y and CONFIG_IP_MROUTE_MULTIPLE_TABLES=y,
the (PF_INET6, RTM_GETROUTE) handler isn't registered, so we end up in
rtnl_dump_all, and listing IPv6 routes will unexpectedly print:
# ip -6 r
Error: ipv4: MR table does not exist.
Dump terminated
commit
ae677bbb4441 introduced the dump_all_families variable, which
gets set when userspace requests a PF_UNSPEC dump. However, we can't
simply set the family to PF_UNSPEC in rtnetlink_rcv_msg in the
fallback case to get dump_all_families == true, because some messages
types (for example RTM_GETRULE and RTM_GETNEIGH) only register the
PF_UNSPEC handler and use the family to filter in the kernel what is
dumped to userspace. We would then export more entries, that userspace
would have to filter. iproute does that, but other programs may not.
Instead, this patch removes dump_all_families and updates the
RTM_GETROUTE handlers to check if the family that is being dumped is
their own. When it's not, which covers both the intentional PF_UNSPEC
dumps (as dump_all_families did) and the fallback case, ignore the
missing table id error.
Fixes:
cb167893f41e ("net: Plumb support for filtering ipv4 and ipv6 multicast route dumps")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Fedorenko [Wed, 20 May 2020 08:50:48 +0000 (11:50 +0300)]
net: ipip: fix wrong address family in init error path
In case of error with MPLS support the code is misusing AF_INET
instead of AF_MPLS.
Fixes:
1b69e7e6c4da ("ipip: support MPLS over IPv4")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 May 2020 00:20:06 +0000 (17:20 -0700)]
Merge branch 'net-tls-fix-encryption-error-path'
Vadim Fedorenko says:
====================
net/tls: fix encryption error path
The problem with data stream corruption was found in KTLS
transmit path with small socket send buffers and large
amount of data. bpf_exec_tx_verdict() frees open record
on any type of error including EAGAIN, ENOMEM and ENOSPC
while callers are able to recover this transient errors.
Also wrong error code was returned to user space in that
case. This patchset fixes the problems.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Fedorenko [Wed, 20 May 2020 08:41:44 +0000 (11:41 +0300)]
net/tls: free record only on encryption error
We cannot free record on any transient error because it leads to
losing previos data. Check socket error to know whether record must
be freed or not.
Fixes:
d10523d0b3d7 ("net/tls: free the record on encryption error")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Fedorenko [Wed, 20 May 2020 08:41:43 +0000 (11:41 +0300)]
net/tls: fix encryption error checking
bpf_exec_tx_verdict() can return negative value for copied
variable. In that case this value will be pushed back to caller
and the real error code will be lost. Fix it using signed type and
checking for positive value.
Fixes:
d10523d0b3d7 ("net/tls: free the record on encryption error")
Fixes:
d3b18ad31f93 ("tls: add bpf support to sk_msg handling")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 22 May 2020 00:14:18 +0000 (17:14 -0700)]
Merge branch 'net-ethernet-ti-fix-some-return-value-check'
Wei Yongjun says:
====================
net: ethernet: ti: fix some return value check
This patchset convert cpsw_ale_create() to return PTR_ERR() only, and
changed all the caller to check IS_ERR() instead of NULL.
Since v2:
1) rebased on net.git, as Jakub's suggest
2) split am65-cpsw-nuss.c changes, as Grygorii's suggest
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 20 May 2020 03:41:16 +0000 (11:41 +0800)]
net: ethernet: ti: am65-cpsw-nuss: fix error handling of am65_cpsw_nuss_probe
Convert to using IS_ERR() instead of NULL test for cpsw_ale_create()
error handling. Also fix to return negative error code from this error
handling case instead of 0 in.
Fixes:
93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 20 May 2020 03:41:15 +0000 (11:41 +0800)]
net: ethernet: ti: fix some return value check of cpsw_ale_create()
cpsw_ale_create() can return both NULL and PTR_ERR(), but all of
the caller only check NULL for error handling. This patch convert
it to only return PTR_ERR() in all error cases, and the caller using
IS_ERR() instead of NULL test.
Fixes:
4b41d3436796 ("net: ethernet: ti: cpsw: allow untagged traffic on host port")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manivannan Sadhasivam [Tue, 19 May 2020 18:14:16 +0000 (23:44 +0530)]
net: qrtr: Fix passing invalid reference to qrtr_local_enqueue()
Once the traversal of the list is completed with list_for_each_entry(),
the iterator (node) will point to an invalid object. So passing this to
qrtr_local_enqueue() which is outside of the iterator block is erroneous
eventhough the object is not used.
So fix this by passing NULL to qrtr_local_enqueue().
Fixes:
bdabad3e363d ("net: Add Qualcomm IPC router")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Sun, 10 May 2020 19:04:09 +0000 (21:04 +0200)]
ethtool: count header size in reply size estimate
As ethnl_request_ops::reply_size handlers do not include common header
size into calculated/estimated reply size, it needs to be added in
ethnl_default_doit() and ethnl_default_notify() before allocating the
message. On the other hand, strset_reply_size() should not add common
header size.
Fixes:
728480f12442 ("ethtool: default handlers for GET requests")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Worley [Wed, 20 May 2020 01:57:12 +0000 (21:57 -0400)]
net: nlmsg_cancel() if put fails for nhmsg
Fixes data remnant seen when we fail to reserve space for a
nexthop group during a larger dump.
If we fail the reservation, we goto nla_put_failure and
cancel the message.
Reproduce with the following iproute2 commands:
=====================
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add dummy3 type dummy
ip link add dummy4 type dummy
ip link add dummy5 type dummy
ip link add dummy6 type dummy
ip link add dummy7 type dummy
ip link add dummy8 type dummy
ip link add dummy9 type dummy
ip link add dummy10 type dummy
ip link add dummy11 type dummy
ip link add dummy12 type dummy
ip link add dummy13 type dummy
ip link add dummy14 type dummy
ip link add dummy15 type dummy
ip link add dummy16 type dummy
ip link add dummy17 type dummy
ip link add dummy18 type dummy
ip link add dummy19 type dummy
ip link add dummy20 type dummy
ip link add dummy21 type dummy
ip link add dummy22 type dummy
ip link add dummy23 type dummy
ip link add dummy24 type dummy
ip link add dummy25 type dummy
ip link add dummy26 type dummy
ip link add dummy27 type dummy
ip link add dummy28 type dummy
ip link add dummy29 type dummy
ip link add dummy30 type dummy
ip link add dummy31 type dummy
ip link add dummy32 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip link set dummy3 up
ip link set dummy4 up
ip link set dummy5 up
ip link set dummy6 up
ip link set dummy7 up
ip link set dummy8 up
ip link set dummy9 up
ip link set dummy10 up
ip link set dummy11 up
ip link set dummy12 up
ip link set dummy13 up
ip link set dummy14 up
ip link set dummy15 up
ip link set dummy16 up
ip link set dummy17 up
ip link set dummy18 up
ip link set dummy19 up
ip link set dummy20 up
ip link set dummy21 up
ip link set dummy22 up
ip link set dummy23 up
ip link set dummy24 up
ip link set dummy25 up
ip link set dummy26 up
ip link set dummy27 up
ip link set dummy28 up
ip link set dummy29 up
ip link set dummy30 up
ip link set dummy31 up
ip link set dummy32 up
ip link set dummy33 up
ip link set dummy34 up
ip link set vrf-red up
ip link set vrf-blue up
ip link set dummyVRFred up
ip link set dummyVRFblue up
ip ro add 1.1.1.1/32 dev dummy1
ip ro add 1.1.1.2/32 dev dummy2
ip ro add 1.1.1.3/32 dev dummy3
ip ro add 1.1.1.4/32 dev dummy4
ip ro add 1.1.1.5/32 dev dummy5
ip ro add 1.1.1.6/32 dev dummy6
ip ro add 1.1.1.7/32 dev dummy7
ip ro add 1.1.1.8/32 dev dummy8
ip ro add 1.1.1.9/32 dev dummy9
ip ro add 1.1.1.10/32 dev dummy10
ip ro add 1.1.1.11/32 dev dummy11
ip ro add 1.1.1.12/32 dev dummy12
ip ro add 1.1.1.13/32 dev dummy13
ip ro add 1.1.1.14/32 dev dummy14
ip ro add 1.1.1.15/32 dev dummy15
ip ro add 1.1.1.16/32 dev dummy16
ip ro add 1.1.1.17/32 dev dummy17
ip ro add 1.1.1.18/32 dev dummy18
ip ro add 1.1.1.19/32 dev dummy19
ip ro add 1.1.1.20/32 dev dummy20
ip ro add 1.1.1.21/32 dev dummy21
ip ro add 1.1.1.22/32 dev dummy22
ip ro add 1.1.1.23/32 dev dummy23
ip ro add 1.1.1.24/32 dev dummy24
ip ro add 1.1.1.25/32 dev dummy25
ip ro add 1.1.1.26/32 dev dummy26
ip ro add 1.1.1.27/32 dev dummy27
ip ro add 1.1.1.28/32 dev dummy28
ip ro add 1.1.1.29/32 dev dummy29
ip ro add 1.1.1.30/32 dev dummy30
ip ro add 1.1.1.31/32 dev dummy31
ip ro add 1.1.1.32/32 dev dummy32
ip next add id 1 via 1.1.1.1 dev dummy1
ip next add id 2 via 1.1.1.2 dev dummy2
ip next add id 3 via 1.1.1.3 dev dummy3
ip next add id 4 via 1.1.1.4 dev dummy4
ip next add id 5 via 1.1.1.5 dev dummy5
ip next add id 6 via 1.1.1.6 dev dummy6
ip next add id 7 via 1.1.1.7 dev dummy7
ip next add id 8 via 1.1.1.8 dev dummy8
ip next add id 9 via 1.1.1.9 dev dummy9
ip next add id 10 via 1.1.1.10 dev dummy10
ip next add id 11 via 1.1.1.11 dev dummy11
ip next add id 12 via 1.1.1.12 dev dummy12
ip next add id 13 via 1.1.1.13 dev dummy13
ip next add id 14 via 1.1.1.14 dev dummy14
ip next add id 15 via 1.1.1.15 dev dummy15
ip next add id 16 via 1.1.1.16 dev dummy16
ip next add id 17 via 1.1.1.17 dev dummy17
ip next add id 18 via 1.1.1.18 dev dummy18
ip next add id 19 via 1.1.1.19 dev dummy19
ip next add id 20 via 1.1.1.20 dev dummy20
ip next add id 21 via 1.1.1.21 dev dummy21
ip next add id 22 via 1.1.1.22 dev dummy22
ip next add id 23 via 1.1.1.23 dev dummy23
ip next add id 24 via 1.1.1.24 dev dummy24
ip next add id 25 via 1.1.1.25 dev dummy25
ip next add id 26 via 1.1.1.26 dev dummy26
ip next add id 27 via 1.1.1.27 dev dummy27
ip next add id 28 via 1.1.1.28 dev dummy28
ip next add id 29 via 1.1.1.29 dev dummy29
ip next add id 30 via 1.1.1.30 dev dummy30
ip next add id 31 via 1.1.1.31 dev dummy31
ip next add id 32 via 1.1.1.32 dev dummy32
i=100
while [ $i -le 200 ]
do
ip next add id $i group 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19
echo $i
((i++))
done
ip next add id 999 group 1/2/3/4/5/6
ip next ls
========================
Fixes:
ab84be7e54fc ("net: Initial nexthop code")
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 20 May 2020 01:24:43 +0000 (18:24 -0700)]
ax25: fix setsockopt(SO_BINDTODEVICE)
syzbot was able to trigger this trace [1], probably by using
a zero optlen.
While we are at it, cap optlen to IFNAMSIZ - 1 instead of IFNAMSIZ.
[1]
BUG: KMSAN: uninit-value in strnlen+0xf9/0x170 lib/string.c:569
CPU: 0 PID: 8807 Comm: syz-executor483 Not tainted 5.7.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
strnlen+0xf9/0x170 lib/string.c:569
dev_name_hash net/core/dev.c:207 [inline]
netdev_name_node_lookup net/core/dev.c:277 [inline]
__dev_get_by_name+0x75/0x2b0 net/core/dev.c:778
ax25_setsockopt+0xfa3/0x1170 net/ax25/af_ax25.c:654
__compat_sys_setsockopt+0x4ed/0x910 net/compat.c:403
__do_compat_sys_setsockopt net/compat.c:413 [inline]
__se_compat_sys_setsockopt+0xdd/0x100 net/compat.c:410
__ia32_compat_sys_setsockopt+0x62/0x80 net/compat.c:410
do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline]
do_fast_syscall_32+0x3bf/0x6d0 arch/x86/entry/common.c:398
entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139
RIP: 0023:0xf7f57dd9
Code: 90 e8 0b 00 00 00 f3 90 0f ae e8 eb f9 8d 74 26 00 89 3c 24 c3 90 90 90 90 90 90 90 90 90 90 90 90 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 eb 0d 90 90 90 90 90 90 90 90 90 90 90 90
RSP: 002b:
00000000ffae8c1c EFLAGS:
00000217 ORIG_RAX:
000000000000016e
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
0000000000000101
RDX:
0000000000000019 RSI:
0000000020000000 RDI:
0000000000000004
RBP:
0000000000000012 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
0000000000000000
R13:
0000000000000000 R14:
0000000000000000 R15:
0000000000000000
Local variable ----devname@ax25_setsockopt created at:
ax25_setsockopt+0xe6/0x1170 net/ax25/af_ax25.c:536
ax25_setsockopt+0xe6/0x1170 net/ax25/af_ax25.c:536
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 21 May 2020 03:55:09 +0000 (20:55 -0700)]
Merge branch 'wireguard-fixes'
Jason A. Donenfeld says:
====================
wireguard fixes for 5.7-rc7
Hopefully these are the last fixes for 5.7:
1) A trivial bump in the selftest harness to support gcc-10.
build.wireguard.com is still on gcc-9 but I'll probably switch to
gcc-10 in the coming weeks.
2) A concurrency fix regarding userspace modifying the pre-shared key at
the same time as packets are being processed, reported by Matt
Dunwoodie.
3) We were previously clearing skb->hash on egress, which broke
fq_codel, cake, and other things that actually make use of the flow
hash for queueing, reported by Dave Taht and Toke Høiland-Jørgensen.
4) A fix for the increased memory usage caused by (3). This can be
thought of as part of patch (3), but because of the separate
reasoning and breadth of it I thought made it a bit cleaner to put in
a standalone commit.
Fixes (2), (3), and (4) are -stable material.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason A. Donenfeld [Wed, 20 May 2020 04:49:30 +0000 (22:49 -0600)]
wireguard: noise: separate receive counter from send counter
In "wireguard: queueing: preserve flow hash across packet scrubbing", we
were required to slightly increase the size of the receive replay
counter to something still fairly small, but an increase nonetheless.
It turns out that we can recoup some of the additional memory overhead
by splitting up the prior union type into two distinct types. Before, we
used the same "noise_counter" union for both sending and receiving, with
sending just using a simple atomic64_t, while receiving used the full
replay counter checker. This meant that most of the memory being
allocated for the sending counter was being wasted. Since the old
"noise_counter" type increased in size in the prior commit, now is a
good time to split up that union type into a distinct "noise_replay_
counter" for receiving and a boring atomic64_t for sending, each using
neither more nor less memory than required.
Also, since sometimes the replay counter is accessed without
necessitating additional accesses to the bitmap, we can reduce cache
misses by hoisting the always-necessary lock above the bitmap in the
struct layout. We also change a "noise_replay_counter" stack allocation
to kmalloc in a -DDEBUG selftest so that KASAN doesn't trigger a stack
frame warning.
All and all, removing a bit of abstraction in this commit makes the code
simpler and smaller, in addition to the motivating memory usage
recuperation. For example, passing around raw "noise_symmetric_key"
structs is something that really only makes sense within noise.c, in the
one place where the sending and receiving keys can safely be thought of
as the same type of object; subsequent to that, it's important that we
uniformly access these through keypair->{sending,receiving}, where their
distinct roles are always made explicit. So this patch allows us to draw
that distinction clearly as well.
Fixes:
e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason A. Donenfeld [Wed, 20 May 2020 04:49:29 +0000 (22:49 -0600)]
wireguard: queueing: preserve flow hash across packet scrubbing
It's important that we clear most header fields during encapsulation and
decapsulation, because the packet is substantially changed, and we don't
want any info leak or logic bug due to an accidental correlation. But,
for encapsulation, it's wrong to clear skb->hash, since it's used by
fq_codel and flow dissection in general. Without it, classification does
not proceed as usual. This change might make it easier to estimate the
number of innerflows by examining clustering of out of order packets,
but this shouldn't open up anything that can't already be inferred
otherwise (e.g. syn packet size inference), and fq_codel can be disabled
anyway.
Furthermore, it might be the case that the hash isn't used or queried at
all until after wireguard transmits the encrypted UDP packet, which
means skb->hash might still be zero at this point, and thus no hash
taken over the inner packet data. In order to address this situation, we
force a calculation of skb->hash before encrypting packet data.
Of course this means that fq_codel might transmit packets slightly more
out of order than usual. Toke did some testing on beefy machines with
high quantities of parallel flows and found that increasing the
reply-attack counter to 8192 takes care of the most pathological cases
pretty well.
Reported-by: Dave Taht <dave.taht@gmail.com>
Reviewed-and-tested-by: Toke Høiland-Jørgensen <toke@toke.dk>
Fixes:
e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason A. Donenfeld [Wed, 20 May 2020 04:49:28 +0000 (22:49 -0600)]
wireguard: noise: read preshared key while taking lock
Prior we read the preshared key after dropping the handshake lock, which
isn't an actual crypto issue if it races, but it's still not quite
correct. So copy that part of the state into a temporary like we do with
the rest of the handshake state variables. Then we can release the lock,
operate on the temporary, and zero it out at the end of the function. In
performance tests, the impact of this was entirely unnoticable, probably
because those bytes are coming from the same cacheline as other things
that are being copied out in the same manner.
Reported-by: Matt Dunwoodie <ncon@noconroy.net>
Fixes:
e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason A. Donenfeld [Wed, 20 May 2020 04:49:27 +0000 (22:49 -0600)]
wireguard: selftests: use newer iproute2 for gcc-10
gcc-10 switched to defaulting to -fno-common, which broke iproute2-5.4.
This was fixed in iproute-5.6, so switch to that. Because we're after a
stable testing surface, we generally don't like to bump these
unnecessarily, but in this case, being able to actually build is a basic
necessity.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrii Nakryiko [Tue, 19 May 2020 05:38:24 +0000 (22:38 -0700)]
bpf: Prevent mmap()'ing read-only maps as writable
As discussed in [0], it's dangerous to allow mapping BPF map, that's meant to
be frozen and is read-only on BPF program side, because that allows user-space
to actually store a writable view to the page even after it is frozen. This is
exacerbated by BPF verifier making a strong assumption that contents of such
frozen map will remain unchanged. To prevent this, disallow mapping
BPF_F_RDONLY_PROG mmap()'able BPF maps as writable, ever.
[0] https://lore.kernel.org/bpf/CAEf4BzYGWYhXdp6BJ7_=9OQPJxQpgug080MMjdSB72i9R+5c6g@mail.gmail.com/
Fixes:
fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY")
Suggested-by: Jann Horn <jannh@google.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/bpf/20200519053824.1089415-1-andriin@fb.com
KP Singh [Wed, 20 May 2020 12:56:16 +0000 (14:56 +0200)]
security: Fix hook iteration for secid_to_secctx
secid_to_secctx is not stackable, and since the BPF LSM registers this
hook by default, the call_int_hook logic is not suitable which
"bails-on-fail" and casues issues when other LSMs register this hook and
eventually breaks Audit.
In order to fix this, directly iterate over the security hooks instead
of using call_int_hook as suggested in:
https: //lore.kernel.org/bpf/
9d0eb6c6-803a-ff3a-5603-
9ad6d9edfc00@schaufler-ca.com/#t
Fixes:
98e828a0650f ("security: Refactor declaration of LSM hooks")
Fixes:
625236ba3832 ("security: Fix the default value of secid_to_secctx hook")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: James Morris <jamorris@linux.microsoft.com>
Link: https://lore.kernel.org/bpf/20200520125616.193765-1-kpsingh@chromium.org
David Howells [Wed, 29 Apr 2020 22:48:43 +0000 (23:48 +0100)]
rxrpc: Fix ack discard
The Rx protocol has a "previousPacket" field in it that is not handled in
the same way by all protocol implementations. Sometimes it contains the
serial number of the last DATA packet received, sometimes the sequence
number of the last DATA packet received and sometimes the highest sequence
number so far received.
AF_RXRPC is using this to weed out ACKs that are out of date (it's possible
for ACK packets to get reordered on the wire), but this does not work with
OpenAFS which will just stick the sequence number of the last packet seen
into previousPacket.
The issue being seen is that big AFS FS.StoreData RPC (eg. of ~256MiB) are
timing out when partly sent. A trace was captured, with an additional
tracepoint to show ACKs being discarded in rxrpc_input_ack(). Here's an
excerpt showing the problem.
52873.203230: rxrpc_tx_data: c=
000004ae DATA
ed1a3584:
00000002 0002449c q=
00024499 fl=09
A DATA packet with sequence number
00024499 has been transmitted (the "q="
field).
...
52873.243296: rxrpc_rx_ack: c=
000004ae 00012a2b DLY r=
00024499 f=
00024497 p=
00024496 n=0
52873.243376: rxrpc_rx_ack: c=
000004ae 00012a2c IDL r=
0002449b f=
00024499 p=
00024498 n=0
52873.243383: rxrpc_rx_ack: c=
000004ae 00012a2d OOS r=
0002449d f=
00024499 p=
0002449a n=2
The Out-Of-Sequence ACK indicates that the server didn't see DATA sequence
number
00024499, but did see seq
0002449a (previousPacket, shown as "p=",
skipped the number, but firstPacket, "f=", which shows the bottom of the
window is set at that point).
52873.252663: rxrpc_retransmit: c=
000004ae q=24499 a=02 xp=
14581537
52873.252664: rxrpc_tx_data: c=
000004ae DATA
ed1a3584:
00000002 000244bc q=
00024499 fl=0b *RETRANS*
The packet has been retransmitted. Retransmission recurs until the peer
says it got the packet.
52873.271013: rxrpc_rx_ack: c=
000004ae 00012a31 OOS r=
000244a1 f=
00024499 p=
0002449e n=6
More OOS ACKs indicate that the other packets that are already in the
transmission pipeline are being received. The specific-ACK list is up to 6
ACKs and NAKs.
...
52873.284792: rxrpc_rx_ack: c=
000004ae 00012a49 OOS r=
000244b9 f=
00024499 p=
000244b6 n=30
52873.284802: rxrpc_retransmit: c=
000004ae q=24499 a=0a xp=
63505500
52873.284804: rxrpc_tx_data: c=
000004ae DATA
ed1a3584:
00000002 000244c2 q=
00024499 fl=0b *RETRANS*
52873.287468: rxrpc_rx_ack: c=
000004ae 00012a4a OOS r=
000244ba f=
00024499 p=
000244b7 n=31
52873.287478: rxrpc_rx_ack: c=
000004ae 00012a4b OOS r=
000244bb f=
00024499 p=
000244b8 n=32
At this point, the server's receive window is full (n=32) with presumably 1
NAK'd packet and 31 ACK'd packets. We can't transmit any more packets.
52873.287488: rxrpc_retransmit: c=
000004ae q=24499 a=0a xp=
61327980
52873.287489: rxrpc_tx_data: c=
000004ae DATA
ed1a3584:
00000002 000244c3 q=
00024499 fl=0b *RETRANS*
52873.293850: rxrpc_rx_ack: c=
000004ae 00012a4c DLY r=
000244bc f=
000244a0 p=
00024499 n=25
And now we've received an ACK indicating that a DATA retransmission was
received. 7 packets have been processed (the occupied part of the window
moved, as indicated by f= and n=).
52873.293853: rxrpc_rx_discard_ack: c=
000004ae r=
00012a4c 000244a0<
00024499 00024499<
000244b8
However, the DLY ACK gets discarded because its previousPacket has gone
backwards (from p=
000244b8, in the ACK at 52873.287478 to p=
00024499 in the
ACK at 52873.293850).
We then end up in a continuous cycle of retransmit/discard. kafs fails to
update its window because it's discarding the ACKs and can't transmit an
extra packet that would clear the issue because the window is full.
OpenAFS doesn't change the previousPacket value in the ACKs because no new
DATA packets are received with a different previousPacket number.
Fix this by altering the discard check to only discard an ACK based on
previousPacket if there was no advance in the firstPacket. This allows us
to transmit a new packet which will cause previousPacket to advance in the
next ACK.
The check, however, needs to allow for the possibility that previousPacket
may actually have had the serial number placed in it instead - in which
case it will go outside the window and we should ignore it.
Fixes:
1a2391c30c0b ("rxrpc: Fix detection of out of order acks")
Reported-by: Dave Botsch <botsch@cnf.cornell.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Tue, 28 Apr 2020 21:06:54 +0000 (22:06 +0100)]
rxrpc: Trace discarded ACKs
Add a tracepoint to track received ACKs that are discarded due to being
outside of the Tx window.
Signed-off-by: David Howells <dhowells@redhat.com>
Neil Horman [Tue, 19 May 2020 20:04:05 +0000 (16:04 -0400)]
sctp: Don't add the shutdown timer if its already been added
This BUG halt was reported a while back, but the patch somehow got
missed:
PID: 2879 TASK:
c16adaa0 CPU: 1 COMMAND: "sctpn"
#0 [
f418dd28] crash_kexec at
c04a7d8c
#1 [
f418dd7c] oops_end at
c0863e02
#2 [
f418dd90] do_invalid_op at
c040aaca
#3 [
f418de28] error_code (via invalid_op) at
c08631a5
EAX:
f34baac0 EBX:
00000090 ECX:
f418deb0 EDX:
f5542950 EBP:
00000000
DS: 007b ESI:
f34ba800 ES: 007b EDI:
f418dea0 GS: 00e0
CS: 0060 EIP:
c046fa5e ERR:
ffffffff EFLAGS:
00010286
#4 [
f418de5c] add_timer at
c046fa5e
#5 [
f418de68] sctp_do_sm at
f8db8c77 [sctp]
#6 [
f418df30] sctp_primitive_SHUTDOWN at
f8dcc1b5 [sctp]
#7 [
f418df48] inet_shutdown at
c080baf9
#8 [
f418df5c] sys_shutdown at
c079eedf
#9 [
f418df70] sys_socketcall at
c079fe88
EAX:
ffffffda EBX:
0000000d ECX:
bfceea90 EDX:
0937af98
DS: 007b ESI:
0000000c ES: 007b EDI:
b7150ae4
SS: 007b ESP:
bfceea7c EBP:
bfceeaa8 GS: 0033
CS: 0073 EIP:
b775c424 ERR:
00000066 EFLAGS:
00000282
It appears that the side effect that starts the shutdown timer was processed
multiple times, which can happen as multiple paths can trigger it. This of
course leads to the BUG halt in add_timer getting called.
Fix seems pretty straightforward, just check before the timer is added if its
already been started. If it has mod the timer instead to min(current
expiration, new expiration)
Its been tested but not confirmed to fix the problem, as the issue has only
occured in production environments where test kernels are enjoined from being
installed. It appears to be a sane fix to me though. Also, recentely,
Jere found a reproducer posted on list to confirm that this resolves the
issues
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: jere.leppanen@nokia.com
CC: marcelo.leitner@gmail.com
CC: netdev@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Boris Sukholitko [Tue, 19 May 2020 07:32:37 +0000 (10:32 +0300)]
__netif_receive_skb_core: pass skb by reference
__netif_receive_skb_core may change the skb pointer passed into it (e.g.
in rx_handler). The original skb may be freed as a result of this
operation.
The callers of __netif_receive_skb_core may further process original skb
by using pt_prev pointer returned by __netif_receive_skb_core thus
leading to unpleasant effects.
The solution is to pass skb by reference into __netif_receive_skb_core.
v2: Added Fixes tag and comment regarding ppt_prev and skb invariant.
Fixes:
88eb1944e18c ("net: core: propagate SKB lists through packet_type lookup")
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Tue, 19 May 2020 00:13:34 +0000 (17:13 -0700)]
net: inet_csk: Fix so_reuseport bind-address cache in tb->fast*
The commit
637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk")
added a bind-address cache in tb->fast*. The tb->fast* caches the address
of a sk which has successfully been binded with SO_REUSEPORT ON. The idea
is to avoid the expensive conflict search in inet_csk_bind_conflict().
There is an issue with wildcard matching where sk_reuseport_match() should
have returned false but it is currently returning true. It ends up
hiding bind conflict. For example,
bind("[::1]:443"); /* without SO_REUSEPORT. Succeed. */
bind("[::2]:443"); /* with SO_REUSEPORT. Succeed. */
bind("[::]:443"); /* with SO_REUSEPORT. Still Succeed where it shouldn't */
The last bind("[::]:443") with SO_REUSEPORT on should have failed because
it should have a conflict with the very first bind("[::1]:443") which
has SO_REUSEPORT off. However, the address "[::2]" is cached in
tb->fast* in the second bind. In the last bind, the sk_reuseport_match()
returns true because the binding sk's wildcard addr "[::]" matches with
the "[::2]" cached in tb->fast*.
The correct bind conflict is reported by removing the second
bind such that tb->fast* cache is not involved and forces the
bind("[::]:443") to go through the inet_csk_bind_conflict():
bind("[::1]:443"); /* without SO_REUSEPORT. Succeed. */
bind("[::]:443"); /* with SO_REUSEPORT. -EADDRINUSE */
The expected behavior for sk_reuseport_match() is, it should only allow
the "cached" tb->fast* address to be used as a wildcard match but not
the address of the binding sk. To do that, the current
"bool match_wildcard" arg is split into
"bool match_sk1_wildcard" and "bool match_sk2_wildcard".
This change only affects the sk_reuseport_match() which is only
used by inet_csk (e.g. TCP).
The other use cases are calling inet_rcv_saddr_equal() and
this patch makes it pass the same "match_wildcard" arg twice to
the "ipv[46]_rcv_saddr_equal(..., match_wildcard, match_wildcard)".
Cc: Josef Bacik <jbacik@fb.com>
Fixes:
637bc8bbe6c0 ("inet: reset tb->fastreuseport when adding a reuseport sk")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Payne [Tue, 19 May 2020 18:01:46 +0000 (19:01 +0100)]
r8152: support additional Microsoft Surface Ethernet Adapter variant
Device id 0927 is the RTL8153B-based component of the 'Surface USB-C to
Ethernet and USB Adapter' and may be used as a component of other devices
in future. Tested and working with the r8152 driver.
Update the cdc_ether blacklist due to the RTL8153 'network jam on suspend'
issue which this device will cause (personally confirmed).
Signed-off-by: Marc Payne <marc.payne@mdpsys.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Todd Malsbary [Tue, 19 May 2020 16:45:34 +0000 (09:45 -0700)]
mptcp: use rightmost 64 bits in ADD_ADDR HMAC
This changes the HMAC used in the ADD_ADDR option from the leftmost 64
bits to the rightmost 64 bits as described in RFC 8684, section 3.4.1.
This issue was discovered while adding support to packetdrill for the
ADD_ADDR v1 option.
Fixes:
3df523ab582c ("mptcp: Add ADD_ADDR handling")
Signed-off-by: Todd Malsbary <todd.malsbary@linux.intel.com>
Acked-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 19 May 2020 19:09:45 +0000 (12:09 -0700)]
Merge tag 'wireless-drivers-2020-05-19' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.7
Third and most likely the last set of fixes for v5.7. Only one
iwlwifi fix this time.
iwlwifi
* another fix for QuZ device configuration
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Kerr [Tue, 19 May 2020 01:05:58 +0000 (09:05 +0800)]
net: bmac: Fix read of MAC address from ROM
In bmac_get_station_address, We're reading two bytes at a time from ROM,
but we do that six times, resulting in 12 bytes of read & writes. This
means we will write off the end of the six-byte destination buffer.
This change fixes the for-loop to only read/write six bytes.
Based on a proposed fix from Finn Thain <fthain@telegraphics.com.au>.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Reported-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Reported-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Mashak [Sun, 17 May 2020 12:46:31 +0000 (08:46 -0400)]
net sched: fix reporting the first-time use timestamp
When a new action is installed, firstuse field of 'tcf_t' is explicitly set
to 0. Value of zero means "new action, not yet used"; as a packet hits the
action, 'firstuse' is stamped with the current jiffies value.
tcf_tm_dump() should return 0 for firstuse if action has not yet been hit.
Fixes:
48d8ee1694dd ("net sched actions: aggregate dumping of actions timeinfo")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Sun, 17 May 2020 11:53:40 +0000 (14:53 +0300)]
net: phy: propagate an error back to the callers of phy_sfp_probe
The compilation warning below reveals that the errors returned from
the sfp_bus_add_upstream() call are not propagated to the callers.
Fix it by returning "ret".
14:37:51 drivers/net/phy/phy_device.c: In function 'phy_sfp_probe':
14:37:51 drivers/net/phy/phy_device.c:1236:6: warning: variable 'ret'
set but not used [-Wunused-but-set-variable]
14:37:51 1236 | int ret;
14:37:51 | ^~~
Fixes:
298e54fa810e ("net: phy: add core phylib sfp support")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuqi Jin [Sat, 16 May 2020 03:46:49 +0000 (11:46 +0800)]
net: revert "net: get rid of an signed integer overflow in ip_idents_reserve()"
Commit
adb03115f459 ("net: get rid of an signed integer overflow in ip_idents_reserve()")
used atomic_cmpxchg to replace "atomic_add_return" inside the function
"ip_idents_reserve". The reason was to avoid UBSAN warning.
However, this change has caused performance degrade and in GCC-8,
fno-strict-overflow is now mapped to -fwrapv -fwrapv-pointer
and signed integer overflow is now undefined by default at all
optimization levels[1]. Moreover, it was a bug in UBSAN vs -fwrapv
/-fno-strict-overflow, so Let's revert it safely.
[1] https://gcc.gnu.org/gcc-8/changes.html
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Suggested-by: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jiong Wang <jiongwang@huawei.com>
Signed-off-by: Yuqi Jin <jinyuqi@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kurt Kanzenbach [Wed, 13 May 2020 14:02:49 +0000 (16:02 +0200)]
dt-bindings: net: dsa: b53: Add missing size and address cells to example
Add the missing size and address cells to the b53 example. Otherwise, it may not
compile or issue warnings if directly copied into a device tree.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sun, 17 May 2020 17:26:32 +0000 (11:26 -0600)]
nexthop: Fix attribute checking for groups
For nexthop groups, attributes after NHA_GROUP_TYPE are invalid, but
nh_check_attr_group starts checking at NHA_GROUP. The group type defaults
to multipath and the NHA_GROUP_TYPE is currently optional so this has
slipped through so far. Fix the attribute checking to handle support of
new group types.
Fixes:
430a049190de ("nexthop: Add support for nexthop groups")
Signed-off-by: ASSOGBA Emery <assogba.emery@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Fri, 15 May 2020 19:52:03 +0000 (14:52 -0500)]
net: ipa: don't be a hog in gsi_channel_poll()
The iteration count value used in gsi_channel_poll() is intended to
limit poll iterations to the budget supplied as an argument. But
it's never updated.
Fix this bug by incrementing the count each time through the loop.
Reported-by: Sharath Chandra Vurukala <sharathv@codeaurora.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
DENG Qingfang [Wed, 13 May 2020 15:10:16 +0000 (23:10 +0800)]
net: dsa: mt7530: fix roaming from DSA user ports
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Fixes:
b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madhuparna Bhowmik [Sat, 16 May 2020 07:45:15 +0000 (13:15 +0530)]
ipv6: Fix suspicious RCU usage warning in ip6mr
This patch fixes the following warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc4-next-
20200507-syzkaller #0 Not tainted
-----------------------------
net/ipv6/ip6mr.c:124 RCU-list traversed in non-reader section!!
ipmr_new_table() returns an existing table, but there is no table at
init. Therefore the condition: either holding rtnl or the list is empty
is used.
Fixes:
d1db275dd3f6e ("ipv6: ip6mr: support multiple tables")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 15 May 2020 20:10:06 +0000 (13:10 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
1) Fix sk_psock reference count leak on receive, from Xiyu Yang.
2) CONFIG_HNS should be invisible, from Geert Uytterhoeven.
3) Don't allow locking route MTUs in ipv6, RFCs actually forbid this,
from Maciej Żenczykowski.
4) ipv4 route redirect backoff wasn't actually enforced, from Paolo
Abeni.
5) Fix netprio cgroup v2 leak, from Zefan Li.
6) Fix infinite loop on rmmod in conntrack, from Florian Westphal.
7) Fix tcp SO_RCVLOWAT hangs, from Eric Dumazet.
8) Various bpf probe handling fixes, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (68 commits)
selftests: mptcp: pm: rm the right tmp file
dpaa2-eth: properly handle buffer size restrictions
bpf: Restrict bpf_trace_printk()'s %s usage and add %pks, %pus specifier
bpf: Add bpf_probe_read_{user, kernel}_str() to do_refine_retval_range
bpf: Restrict bpf_probe_read{, str}() only to archs where they work
MAINTAINERS: Mark networking drivers as Maintained.
ipmr: Add lockdep expression to ipmr_for_each_table macro
ipmr: Fix RCU list debugging warning
drivers: net: hamradio: Fix suspicious RCU usage warning in bpqether.c
net: phy: broadcom: fix BCM54XX_SHD_SCR3_TRDDAPD value for BCM54810
tcp: fix error recovery in tcp_zerocopy_receive()
MAINTAINERS: Add Jakub to networking drivers.
MAINTAINERS: another add of Karsten Graul for S390 networking
drivers: ipa: fix typos for ipa_smp2p structure doc
pppoe: only process PADT targeted at local interfaces
selftests/bpf: Enforce returning 0 for fentry/fexit programs
bpf: Enforce returning 0 for fentry/fexit progs
net: stmmac: fix num_por initialization
security: Fix the default value of secid_to_secctx hook
libbpf: Fix register naming in PT_REGS s390 macros
...
Linus Torvalds [Fri, 15 May 2020 20:06:56 +0000 (13:06 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A few minor bug fixes for user visible defects, and one regression:
- Various bugs from static checkers and syzkaller
- Add missing error checking in mlx4
- Prevent RTNL lock recursion in i40iw
- Fix segfault in cxgb4 in peer abort cases
- Fix a regression added in 5.7 where the IB_EVENT_DEVICE_FATAL could
be lost, and wasn't delivered to all the FDs"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/uverbs: Move IB_EVENT_DEVICE_FATAL to destroy_uobj
RDMA/uverbs: Do not discard the IB_EVENT_DEVICE_FATAL event
RDMA/iw_cxgb4: Fix incorrect function parameters
RDMA/core: Fix double put of resource
IB/core: Fix potential NULL pointer dereference in pkey cache
IB/hfi1: Fix another case where pq is left on waitlist
IB/i40iw: Remove bogus call to netdev_master_upper_dev_get()
IB/mlx4: Test return value of calls to ib_get_cached_pkey
RDMA/rxe: Always return ERR_PTR from rxe_create_mmap_info()
i40iw: Fix error handling in i40iw_manage_arp_cache()
Linus Torvalds [Fri, 15 May 2020 19:57:50 +0000 (12:57 -0700)]
Merge tag 'linux-kselftest-5.7-rc6' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
- lkdtm runner fixes to prevent dmesg clearing and shellcheck errors
- ftrace test handling when test module doesn't exist
- nsfs test fix to replace zero-length array with flexible-array
- dmabuf-heaps test fix to return clear error value
* tag 'linux-kselftest-5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/lkdtm: Use grep -E instead of egrep
selftests/lkdtm: Don't clear dmesg when running tests
selftests/ftrace: mark irqsoff_tracer.tc test as unresolved if the test module does not exist
tools/testing: Replace zero-length array with flexible-array
kselftests: dmabuf-heaps: Fix confused return value on expected error testing
Linus Torvalds [Fri, 15 May 2020 19:47:15 +0000 (12:47 -0700)]
Merge tag 'riscv-for-linus-5.7-rc6' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"A handful of build fixes, all found by Huawei's autobuilder.
None of these patches should have any functional impact on kernels
that build, and they're mostly related to various features
intermingling with !MMU.
While some of these might be better hoisted to generic code, it seems
better to have the simple fixes in the meanwhile.
As far as I know these are the only outstanding patches for 5.7"
* tag 'riscv-for-linus-5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: mmiowb: Fix implicit declaration of function 'smp_processor_id'
riscv: pgtable: Fix __kernel_map_pages build error if NOMMU
riscv: Make SYS_SUPPORTS_HUGETLBFS depends on MMU
riscv: Disable ARCH_HAS_DEBUG_VIRTUAL if NOMMU
riscv: Add pgprot_writecombine/device and PAGE_SHARED defination if NOMMU
riscv: stacktrace: Fix undefined reference to `walk_stackframe'
riscv: Fix unmet direct dependencies built based on SOC_VIRT
riscv: perf: RISCV_BASE_PMU should be independent
riscv: perf_event: Make some funciton static
Linus Torvalds [Fri, 15 May 2020 18:08:46 +0000 (11:08 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Fix flush_icache_range() second argument in machine_kexec() to be an
address rather than size"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: fix the flush_icache_range arguments in machine_kexec
David S. Miller [Fri, 15 May 2020 17:57:21 +0000 (10:57 -0700)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Alexei Starovoitov says:
====================
pull-request: bpf 2020-05-15
The following pull-request contains BPF updates for your *net* tree.
We've added 9 non-merge commits during the last 2 day(s) which contain
a total of 14 files changed, 137 insertions(+), 43 deletions(-).
The main changes are:
1) Fix secid_to_secctx LSM hook default value, from Anders.
2) Fix bug in mmap of bpf array, from Andrii.
3) Restrict bpf_probe_read to archs where they work, from Daniel.
4) Enforce returning 0 for fentry/fexit progs, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthieu Baerts [Fri, 15 May 2020 15:54:41 +0000 (17:54 +0200)]
selftests: mptcp: pm: rm the right tmp file
"$err" is a variable pointing to a temp file. "$out" is not: only used
as a local variable in "check()" and representing the output of a
command line.
Fixes:
eedbc685321b (selftests: add PM netlink functional tests)
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Fri, 15 May 2020 12:30:22 +0000 (15:30 +0300)]
dpaa2-eth: properly handle buffer size restrictions
Depending on the WRIOP version, the buffer size on the RX path must by a
multiple of 64 or 256. Handle this restriction properly by aligning down
the buffer size to the necessary value. Also, use the new buffer size
dynamically computed instead of the compile time one.
Fixes:
27c874867c4e ("dpaa2-eth: Use a single page per Rx buffer")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 15 May 2020 17:14:05 +0000 (10:14 -0700)]
Merge tag 'hwmon-for-v5.7-rc6' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix ADC access synchronization problem with da9052 driver
- Fix temperature limit and status reporting in nct7904 driver
- Fix drivetemp temperature reporting if SCT is supported but SCT data
tables are not.
* tag 'hwmon-for-v5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (da9052) Synchronize access with mfd
hwmon: (nct7904) Fix incorrect range of temperature limit registers
hwmon: (nct7904) Read all SMI status registers in probe function
hwmon: (drivetemp) Fix SCT support if SCT data tables are not supported
Linus Torvalds [Fri, 15 May 2020 17:06:49 +0000 (10:06 -0700)]
Merge tag 'sound-5.7-rc6' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Things look good and calming down; the only change to ALSA core is the
fix for racy rawmidi buffer accesses spotted by syzkaller, and the
rest are all small device-specific quirks for HD-audio and USB-audio
devices"
* tag 'sound-5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Limit int mic boost for Thinkpad T530
ALSA: hda/realtek - Add COEF workaround for ASUS ZenBook UX431DA
ALSA: hda/realtek: Enable headset mic of ASUS UX581LV with ALC295
ALSA: hda/realtek - Enable headset mic of ASUS UX550GE with ALC295
ALSA: hda/realtek - Enable headset mic of ASUS GL503VM with ALC295
ALSA: hda/realtek: Add quirk for Samsung Notebook
ALSA: rawmidi: Fix racy buffer resize under concurrent accesses
ALSA: usb-audio: add mapping for ASRock TRX40 Creator
ALSA: hda/realtek - Fix S3 pop noise on Dell Wyse
Revert "ALSA: hda/realtek: Fix pop noise on ALC225"
ALSA: firewire-lib: fix 'function sizeof not defined' error of tracepoints format
ALSA: usb-audio: Add control message quirk delay for Kingston HyperX headset
Linus Torvalds [Fri, 15 May 2020 16:59:49 +0000 (09:59 -0700)]
Merge tag 'drm-fixes-2020-05-15' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"As mentioned last week an i915 PR came in late, but I left it, so the
i915 bits of this cover 2 weeks, which is why it's likely a bit larger
than usual.
Otherwise it's mostly amdgpu fixes, one tegra fix, one meson fix.
i915:
- Handle idling during i915_gem_evict_something busy loops (Chris)
- Mark current submissions with a weak-dependency (Chris)
- Propagate error from completed fences (Chris)
- Fixes on execlist to avoid GPU hang situation (Chris)
- Fixes couple deadlocks (Chris)
- Timeslice preemption fixes (Chris)
- Fix Display Port interrupt handling on Tiger Lake (Imre)
- Reduce debug noise around Frame Buffer Compression (Peter)
- Fix logic around IPC W/a for Coffee Lake and Kaby Lake (Sultan)
- Avoid dereferencing a dead context (Chris)
tegra:
- tegra120/4 smmu fixes
amdgpu:
- Clockgating fixes
- Fix fbdev with scatter/gather display
- S4 fix for navi
- Soft recovery for gfx10
- Freesync fixes
- Atomic check cursor fix
- Add a gfxoff quirk
- MST fix
amdkfd:
- Fix GEM reference counting
meson:
- error code propogation fix"
* tag 'drm-fixes-2020-05-15' of git://anongit.freedesktop.org/drm/drm: (29 commits)
drm/i915: Handle idling during i915_gem_evict_something busy loops
drm/meson: pm resume add return errno branch
drm/amd/amdgpu: Update update_config() logic
drm/amd/amdgpu: add raven1 part to the gfxoff quirk list
drm/i915: Mark concurrent submissions with a weak-dependency
drm/i915: Propagate error from completed fences
drm/i915/gvt: Fix kernel oops for 3-level ppgtt guest
drm/i915/gvt: Init DPLL/DDI vreg for virtual display instead of inheritance.
drm/amd/display: add basic atomic check for cursor plane
drm/amd/display: Fix vblank and pageflip event handling for FreeSync
drm/amdgpu: implement soft_recovery for gfx10
drm/amdgpu: enable hibernate support on Navi1X
drm/amdgpu: Use GEM obj reference for KFD BOs
drm/amdgpu: force fbdev into vram
drm/amd/powerplay: perform PG ungate prior to CG ungate
drm/amdgpu: drop unnecessary cancel_delayed_work_sync on PG ungate
drm/amdgpu: disable MGCG/MGLS also on gfx CG ungate
drm/i915/execlists: Track inflight CCID
drm/i915/execlists: Avoid reusing the same logical CCID
drm/i915/gem: Remove object_is_locked assertion from unpin_from_display_plane
...
Alexei Starovoitov [Fri, 15 May 2020 15:10:36 +0000 (08:10 -0700)]
Merge branch 'restrict-bpf_probe_read'
Daniel Borkmann says:
====================
Small set of fixes in order to restrict BPF helpers for tracing which are
broken on archs with overlapping address ranges as per discussion in [0].
I've targetted this for -bpf tree so they can be routed as fixes. Thanks!
v1 -> v2:
- switch to reusable %pks, %pus format specifiers (Yonghong)
- fixate %s on kernel_ds probing for archs with overlapping addr space
[0] https://lore.kernel.org/bpf/CAHk-=wjJKo0GVixYLmqPn-Q22WFu0xHaBSjKEo7e7Yw72y5SPQ@mail.gmail.com/T/
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Fri, 15 May 2020 10:11:18 +0000 (12:11 +0200)]
bpf: Restrict bpf_trace_printk()'s %s usage and add %pks, %pus specifier
Usage of plain %s conversion specifier in bpf_trace_printk() suffers from the
very same issue as bpf_probe_read{,str}() helpers, that is, it is broken on
archs with overlapping address ranges.
While the helpers have been addressed through work in
6ae08ae3dea2 ("bpf: Add
probe_read_{user, kernel} and probe_read_{user, kernel}_str helpers"), we need
an option for bpf_trace_printk() as well to fix it.
Similarly as with the helpers, force users to make an explicit choice by adding
%pks and %pus specifier to bpf_trace_printk() which will then pick the corresponding
strncpy_from_unsafe*() variant to perform the access under KERNEL_DS or USER_DS.
The %pk* (kernel specifier) and %pu* (user specifier) can later also be extended
for other objects aside strings that are probed and printed under tracing, and
reused out of other facilities like bpf_seq_printf() or BTF based type printing.
Existing behavior of %s for current users is still kept working for archs where it
is not broken and therefore gated through CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE.
For archs not having this property we fall-back to pick probing under KERNEL_DS as
a sensible default.
Fixes:
8d3b7dce8622 ("bpf: add support for %s specifier to bpf_trace_printk()")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Link: https://lore.kernel.org/bpf/20200515101118.6508-4-daniel@iogearbox.net
Daniel Borkmann [Fri, 15 May 2020 10:11:17 +0000 (12:11 +0200)]
bpf: Add bpf_probe_read_{user, kernel}_str() to do_refine_retval_range
Given bpf_probe_read{,str}() BPF helpers are now only available under
CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE, we need to add the drop-in
replacements of bpf_probe_read_{kernel,user}_str() to do_refine_retval_range()
as well to avoid hitting the same issue as in
849fa50662fbc ("bpf/verifier:
refine retval R0 state for bpf_get_stack helper").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200515101118.6508-3-daniel@iogearbox.net
Daniel Borkmann [Fri, 15 May 2020 10:11:16 +0000 (12:11 +0200)]
bpf: Restrict bpf_probe_read{, str}() only to archs where they work
Given the legacy bpf_probe_read{,str}() BPF helpers are broken on archs
with overlapping address ranges, we should really take the next step to
disable them from BPF use there.
To generally fix the situation, we've recently added new helper variants
bpf_probe_read_{user,kernel}() and bpf_probe_read_{user,kernel}_str().
For details on them, see
6ae08ae3dea2 ("bpf: Add probe_read_{user, kernel}
and probe_read_{user,kernel}_str helpers").
Given bpf_probe_read{,str}() have been around for ~5 years by now, there
are plenty of users at least on x86 still relying on them today, so we
cannot remove them entirely w/o breaking the BPF tracing ecosystem.
However, their use should be restricted to archs with non-overlapping
address ranges where they are working in their current form. Therefore,
move this behind a CONFIG_ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE and
have x86, arm64, arm select it (other archs supporting it can follow-up
on it as well).
For the remaining archs, they can workaround easily by relying on the
feature probe from bpftool which spills out defines that can be used out
of BPF C code to implement the drop-in replacement for old/new kernels
via: bpftool feature probe macro
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/bpf/20200515101118.6508-2-daniel@iogearbox.net
Dave Airlie [Fri, 15 May 2020 06:00:53 +0000 (16:00 +1000)]
Merge tag 'drm-misc-fixes-2020-05-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Just one meson patch this time to propagate an error code
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514073538.wvdtv5s2mt4wdrdj@gilmour.lan
Dave Airlie [Fri, 15 May 2020 02:28:46 +0000 (12:28 +1000)]
Merge tag 'drm-intel-fixes-2020-05-13-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Handle idling during i915_gem_evict_something busy loops (Chris)
- Mark current submissions with a weak-dependency (Chris)
- Propagate errror from completed fences (Chris)
- Fixes on execlist to avoid GPU hang situation (Chris)
- Fixes couple deadlocks (Chris)
- Timeslice preemption fixes (Chris)
- Fix Display Port interrupt handling on Tiger Lake (Imre)
- Reduce debug noise around Frame Buffer Compression
+(Peter)
- Fix logic around IPC W/a for Coffee Lake and Kaby Lake
+(Sultan)
- Avoid dereferencing a dead context (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514040235.GA2164266@intel.com
David S. Miller [Fri, 15 May 2020 01:04:41 +0000 (18:04 -0700)]
MAINTAINERS: Mark networking drivers as Maintained.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amol Grover [Thu, 14 May 2020 18:01:03 +0000 (23:31 +0530)]
ipmr: Add lockdep expression to ipmr_for_each_table macro
During the initialization process, ipmr_new_table() is called
to create new tables which in turn calls ipmr_get_table() which
traverses net->ipv4.mr_tables without holding the writer lock.
However, this is safe to do so as no tables exist at this time.
Hence add a suitable lockdep expression to silence the following
false-positive warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc3-next-
20200428-syzkaller #0 Not tainted
-----------------------------
net/ipv4/ipmr.c:136 RCU-list traversed in non-reader section!!
ipmr_get_table+0x130/0x160 net/ipv4/ipmr.c:136
ipmr_new_table net/ipv4/ipmr.c:403 [inline]
ipmr_rules_init net/ipv4/ipmr.c:248 [inline]
ipmr_net_init+0x133/0x430 net/ipv4/ipmr.c:3089
Fixes:
f0ad0860d01e ("ipv4: ipmr: support multiple tables")
Reported-by: syzbot+1519f497f2f9f08183c6@syzkaller.appspotmail.com
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amol Grover [Thu, 14 May 2020 18:01:02 +0000 (23:31 +0530)]
ipmr: Fix RCU list debugging warning
ipmr_for_each_table() macro uses list_for_each_entry_rcu()
for traversing outside of an RCU read side critical section
but under the protection of rtnl_mutex. Hence, add the
corresponding lockdep expression to silence the following
false-positive warning at boot:
[ 4.319347] =============================
[ 4.319349] WARNING: suspicious RCU usage
[ 4.319351] 5.5.4-stable #17 Tainted: G E
[ 4.319352] -----------------------------
[ 4.319354] net/ipv4/ipmr.c:1757 RCU-list traversed in non-reader section!!
Fixes:
f0ad0860d01e ("ipv4: ipmr: support multiple tables")
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madhuparna Bhowmik [Thu, 14 May 2020 14:11:15 +0000 (19:41 +0530)]
drivers: net: hamradio: Fix suspicious RCU usage warning in bpqether.c
This patch fixes the following warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc5-next-
20200514-syzkaller #0 Not tainted
-----------------------------
drivers/net/hamradio/bpqether.c:149 RCU-list traversed in non-reader section!!
Since rtnl lock is held, pass this cond in list_for_each_entry_rcu().
Reported-by: syzbot+bb82cafc737c002d11ca@syzkaller.appspotmail.com
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Lo [Thu, 14 May 2020 00:57:33 +0000 (08:57 +0800)]
net: phy: broadcom: fix BCM54XX_SHD_SCR3_TRDDAPD value for BCM54810
Set the correct bit when checking for PHY_BRCM_DIS_TXCRXC_NOENRGY on the
BCM54810 PHY.
Fixes:
0ececcfc9267 ("net: phy: broadcom: Allow BCM54810 to use bcm54xx_adjust_rxrefclk()")
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 14 May 2020 20:58:13 +0000 (13:58 -0700)]
tcp: fix error recovery in tcp_zerocopy_receive()
If user provides wrong virtual address in TCP_ZEROCOPY_RECEIVE
operation we want to return -EINVAL error.
But depending on zc->recv_skip_hint content, we might return
-EIO error if the socket has SOCK_DONE set.
Make sure to return -EINVAL in this case.
BUG: KMSAN: uninit-value in tcp_zerocopy_receive net/ipv4/tcp.c:1833 [inline]
BUG: KMSAN: uninit-value in do_tcp_getsockopt+0x4494/0x6320 net/ipv4/tcp.c:3685
CPU: 1 PID: 625 Comm: syz-executor.0 Not tainted 5.7.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x220 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
tcp_zerocopy_receive net/ipv4/tcp.c:1833 [inline]
do_tcp_getsockopt+0x4494/0x6320 net/ipv4/tcp.c:3685
tcp_getsockopt+0xf8/0x1f0 net/ipv4/tcp.c:3728
sock_common_getsockopt+0x13f/0x180 net/core/sock.c:3131
__sys_getsockopt+0x533/0x7b0 net/socket.c:2177
__do_sys_getsockopt net/socket.c:2192 [inline]
__se_sys_getsockopt+0xe1/0x100 net/socket.c:2189
__x64_sys_getsockopt+0x62/0x80 net/socket.c:2189
do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:297
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45c829
Code: 0d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 db b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007f1deeb72c78 EFLAGS:
00000246 ORIG_RAX:
0000000000000037
RAX:
ffffffffffffffda RBX:
00000000004e01e0 RCX:
000000000045c829
RDX:
0000000000000023 RSI:
0000000000000006 RDI:
0000000000000009
RBP:
000000000078bf00 R08:
0000000020000200 R09:
0000000000000000
R10:
00000000200001c0 R11:
0000000000000246 R12:
00000000ffffffff
R13:
00000000000001d8 R14:
00000000004d3038 R15:
00007f1deeb736d4
Local variable ----zc@do_tcp_getsockopt created at:
do_tcp_getsockopt+0x1a74/0x6320 net/ipv4/tcp.c:3670
do_tcp_getsockopt+0x1a74/0x6320 net/ipv4/tcp.c:3670
Fixes:
05255b823a61 ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 14 May 2020 20:24:23 +0000 (13:24 -0700)]
Merge tag 'mmc-v5.7-rc4' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix a couple of quite severe issues for the CQE request path
MMC host:
- alcor: Fix a resource leak in the error path for ->probe()
- sdhci-acpi: Fix the DMA support for the AMD eMMC v5.0 variant
- sdhci-pci-gli: Fix system resume support for GL975x
- sdhci-pci-gli: Fix reboot error for GL9750"
* tag 'mmc-v5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-acpi: Add SDHCI_QUIRK2_BROKEN_64_BIT_DMA for AMDI0040
mmc: block: Fix request completion in the CQE timeout path
mmc: core: Fix recursive locking issue in CQE recovery path
mmc: core: Check request type before completing the request
mmc: sdhci-pci-gli: Fix can not access GL9750 after reboot from Windows 10
mmc: alcor: Fix a resource leak in the error path for ->probe()
mmc: sdhci-pci-gli: Fix no irq handler from suspend
David S. Miller [Thu, 14 May 2020 20:15:02 +0000 (13:15 -0700)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix gcc-10 compilation warning in nf_conntrack, from Arnd Bergmann.
2) Add NF_FLOW_HW_PENDING to avoid races between stats and deletion
commands, from Paul Blakey.
3) Remove WQ_MEM_RECLAIM from the offload workqueue, from Roi Dayan.
4) Infinite loop when removing nf_conntrack module, from Florian Westphal.
5) Set NF_FLOW_TEARDOWN bit on expiration to avoid races when refreshing
the timeout from the software path.
6) Missing nft_set_elem_expired() check in the rbtree, from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 14 May 2020 20:13:07 +0000 (13:13 -0700)]
MAINTAINERS: Add Jakub to networking drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 14 May 2020 11:45:12 +0000 (13:45 +0200)]
MAINTAINERS: another add of Karsten Graul for S390 networking
Complete adding of Karsten as maintainer for all S390 networking
parts in the kernel.
Cc: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Wenhu [Thu, 14 May 2020 11:02:22 +0000 (04:02 -0700)]
drivers: ipa: fix typos for ipa_smp2p structure doc
Remove the duplicate "mutex", and change "Motex" to "Mutex". Also I
recommend it's easier for understanding to make the "ready-interrupt"
a bundle for it is a parallel description as "shutdown" which is appended
after the slash.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Cc: Alex Elder <elder@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Thu, 14 May 2020 10:15:39 +0000 (12:15 +0200)]
pppoe: only process PADT targeted at local interfaces
We don't want to disconnect a session because of a stray PADT arriving
while the interface is in promiscuous mode.
Furthermore, multicast and broadcast packets make no sense here, so
only PACKET_HOST is accepted.
Reported-by: David Balažic <xerces9@gmail.com>
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Thu, 14 May 2020 05:32:07 +0000 (22:32 -0700)]
selftests/bpf: Enforce returning 0 for fentry/fexit programs
There are a few fentry/fexit programs returning non-0.
The tests with these programs will break with the previous
patch which enfoced return-0 rules. Fix them properly.
Fixes:
ac065870d928 ("selftests/bpf: Add BPF_PROG, BPF_KPROBE, and BPF_KRETPROBE macros")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200514053207.1298479-1-yhs@fb.com
Yonghong Song [Thu, 14 May 2020 05:32:05 +0000 (22:32 -0700)]
bpf: Enforce returning 0 for fentry/fexit progs
Currently, tracing/fentry and tracing/fexit prog
return values are not enforced. In trampoline codes,
the fentry/fexit prog return values are ignored.
Let us enforce it to be 0 to avoid confusion and
allows potential future extension.
This patch also explicitly added return value
checking for tracing/raw_tp, tracing/fmod_ret,
and freplace programs such that these program
return values can be anything. The purpose are
two folds:
1. to make it explicit about return value expectations
for these programs in verifier.
2. for tracing prog_type, if a future attach type
is added, the default is -ENOTSUPP which will
enforce to specify return value ranges explicitly.
Fixes:
fec56f5890d9 ("bpf: Introduce BPF trampoline")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200514053206.1298415-1-yhs@fb.com
Vinod Koul [Thu, 14 May 2020 06:28:36 +0000 (11:58 +0530)]
net: stmmac: fix num_por initialization
Driver missed initializing num_por which is one of the por values that
driver configures to hardware. In order to get these values, add a new
structure ethqos_emac_driver_data which holds por and num_por values
and populate that in driver probe.
Fixes:
a7c30e62d4b8 ("net: stmmac: Add driver for Qualcomm ethqos")
Reported-by: Rahul Ankushrao Kawadgave <rahulak@qti.qualcomm.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anders Roxell [Tue, 12 May 2020 17:46:07 +0000 (19:46 +0200)]
security: Fix the default value of secid_to_secctx hook
security_secid_to_secctx is called by the bpf_lsm hook and a successful
return value (i.e 0) implies that the parameter will be consumed by the
LSM framework. The current behaviour return success when the pointer
isn't initialized when CONFIG_BPF_LSM is enabled, with the default
return from kernel/bpf/bpf_lsm.c.
This is the internal error:
[ 1229.341488][ T2659] usercopy: Kernel memory exposure attempt detected from null address (offset 0, size 280)!
[ 1229.374977][ T2659] ------------[ cut here ]------------
[ 1229.376813][ T2659] kernel BUG at mm/usercopy.c:99!
[ 1229.378398][ T2659] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 1229.380348][ T2659] Modules linked in:
[ 1229.381654][ T2659] CPU: 0 PID: 2659 Comm: systemd-journal Tainted: G B W
5.7.0-rc5-next-20200511-00019-g864e0c6319b8-dirty #13
[ 1229.385429][ T2659] Hardware name: linux,dummy-virt (DT)
[ 1229.387143][ T2659] pstate:
80400005 (Nzcv daif +PAN -UAO BTYPE=--)
[ 1229.389165][ T2659] pc : usercopy_abort+0xc8/0xcc
[ 1229.390705][ T2659] lr : usercopy_abort+0xc8/0xcc
[ 1229.392225][ T2659] sp :
ffff000064247450
[ 1229.393533][ T2659] x29:
ffff000064247460 x28:
0000000000000000
[ 1229.395449][ T2659] x27:
0000000000000118 x26:
0000000000000000
[ 1229.397384][ T2659] x25:
ffffa000127049e0 x24:
ffffa000127049e0
[ 1229.399306][ T2659] x23:
ffffa000127048e0 x22:
ffffa000127048a0
[ 1229.401241][ T2659] x21:
ffffa00012704b80 x20:
ffffa000127049e0
[ 1229.403163][ T2659] x19:
ffffa00012704820 x18:
0000000000000000
[ 1229.405094][ T2659] x17:
0000000000000000 x16:
0000000000000000
[ 1229.407008][ T2659] x15:
0000000000000000 x14:
003d090000000000
[ 1229.408942][ T2659] x13:
ffff80000d5b25b2 x12:
1fffe0000d5b25b1
[ 1229.410859][ T2659] x11:
1fffe0000d5b25b1 x10:
ffff80000d5b25b1
[ 1229.412791][ T2659] x9 :
ffffa0001034bee0 x8 :
ffff00006ad92d8f
[ 1229.414707][ T2659] x7 :
0000000000000000 x6 :
ffffa00015eacb20
[ 1229.416642][ T2659] x5 :
ffff0000693c8040 x4 :
0000000000000000
[ 1229.418558][ T2659] x3 :
ffffa0001034befc x2 :
d57a7483a01c6300
[ 1229.420610][ T2659] x1 :
0000000000000000 x0 :
0000000000000059
[ 1229.422526][ T2659] Call trace:
[ 1229.423631][ T2659] usercopy_abort+0xc8/0xcc
[ 1229.425091][ T2659] __check_object_size+0xdc/0x7d4
[ 1229.426729][ T2659] put_cmsg+0xa30/0xa90
[ 1229.428132][ T2659] unix_dgram_recvmsg+0x80c/0x930
[ 1229.429731][ T2659] sock_recvmsg+0x9c/0xc0
[ 1229.431123][ T2659] ____sys_recvmsg+0x1cc/0x5f8
[ 1229.432663][ T2659] ___sys_recvmsg+0x100/0x160
[ 1229.434151][ T2659] __sys_recvmsg+0x110/0x1a8
[ 1229.435623][ T2659] __arm64_sys_recvmsg+0x58/0x70
[ 1229.437218][ T2659] el0_svc_common.constprop.1+0x29c/0x340
[ 1229.438994][ T2659] do_el0_svc+0xe8/0x108
[ 1229.440587][ T2659] el0_svc+0x74/0x88
[ 1229.441917][ T2659] el0_sync_handler+0xe4/0x8b4
[ 1229.443464][ T2659] el0_sync+0x17c/0x180
[ 1229.444920][ T2659] Code:
aa1703e2 aa1603e1 910a8260 97ecc860 (
d4210000)
[ 1229.447070][ T2659] ---[ end trace
400497d91baeaf51 ]---
[ 1229.448791][ T2659] Kernel panic - not syncing: Fatal exception
[ 1229.450692][ T2659] Kernel Offset: disabled
[ 1229.452061][ T2659] CPU features: 0x240002,
20002004
[ 1229.453647][ T2659] Memory Limit: none
[ 1229.455015][ T2659] ---[ end Kernel panic - not syncing: Fatal exception ]---
Rework the so the default return value is -EOPNOTSUPP.
There are likely other callbacks such as security_inode_getsecctx() that
may have the same problem, and that someone that understand the code
better needs to audit them.
Thank you Arnd for helping me figure out what went wrong.
Fixes:
98e828a0650f ("security: Refactor declaration of LSM hooks")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: James Morris <jamorris@linux.microsoft.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/bpf/20200512174607.9630-1-anders.roxell@linaro.org
Sumanth Korikkar [Wed, 13 May 2020 15:44:14 +0000 (17:44 +0200)]
libbpf: Fix register naming in PT_REGS s390 macros
Fix register naming in PT_REGS s390 macros
Fixes:
b8ebce86ffe6 ("libbpf: Provide CO-RE variants of PT_REGS macros")
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513154414.29972-1-sumanthk@linux.ibm.com
Andrii Nakryiko [Tue, 12 May 2020 23:59:25 +0000 (16:59 -0700)]
bpf: Fix bug in mmap() implementation for BPF array map
mmap() subsystem allows user-space application to memory-map region with
initial page offset. This wasn't taken into account in initial implementation
of BPF array memory-mapping. This would result in wrong pages, not taking into
account requested page shift, being memory-mmaped into user-space. This patch
fixes this gap and adds a test for such scenario.
Fixes:
fc9702273e2e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200512235925.3817805-1-andriin@fb.com
Matteo Croce [Mon, 11 May 2020 11:32:34 +0000 (13:32 +0200)]
samples: bpf: Fix build error
GCC 10 is very strict about symbol clash, and lwt_len_hist_user contains
a symbol which clashes with libbpf:
/usr/bin/ld: samples/bpf/lwt_len_hist_user.o:(.bss+0x0): multiple definition of `bpf_log_buf'; samples/bpf/bpf_load.o:(.bss+0x8c0): first defined here
collect2: error: ld returned 1 exit status
bpf_log_buf here seems to be a leftover, so removing it.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200511113234.80722-1-mcroce@redhat.com
Linus Torvalds [Thu, 14 May 2020 19:26:55 +0000 (12:26 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"7 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kasan: add missing functions declarations to kasan.h
kasan: consistently disable debugging features
ipc/util.c: sysvipc_find_ipc() incorrectly updates position index
userfaultfd: fix remap event with MREMAP_DONTUNMAP
mm/gup: fix fixup_user_fault() on multiple retries
epoll: call final ep_events_available() check under the lock
mm, memcg: fix inconsistent oom event behavior
Linus Torvalds [Thu, 14 May 2020 18:52:28 +0000 (11:52 -0700)]
Merge tag 'for-linus-2020-05-13' of git://git./linux/kernel/git/brauner/linux
Pull thread fix from Christian Brauner:
"This contains a single fix for all exported legacy fork helpers to
block accidental access to clone3() features in the upper 32 bits of
their respective flags arguments.
I got Cced on a glibc issue where someone reported consistent failures
for the legacy clone() syscall on ppc64le when sign extension was
performed (since the clone() syscall in glibc exposes the flags
argument as an int whereas the kernel uses unsigned long).
The legacy clone() syscall is odd in a bunch of ways and here two
things interact:
- First, legacy clone's flag argument is word-size dependent, i.e.
it's an unsigned long whereas most system calls with flag arguments
use int or unsigned int.
- Second, legacy clone() ignores unknown and deprecated flags.
The two of them taken together means that users on 64bit systems can
pass garbage for the upper 32bit of the clone() syscall since forever
and things would just work fine.
The following program compiled on a 64bit kernel prior to v5.7-rc1
will succeed and will fail post v5.7-rc1 with EBADF:
int main(int argc, char *argv[])
{
pid_t pid;
/* Note that legacy clone() has different argument ordering on
* different architectures so this won't work everywhere.
*
* Only set the upper 32 bits.
*/
pid = syscall(__NR_clone, 0xffffffff00000000 | SIGCHLD,
NULL, NULL, NULL, NULL);
if (pid < 0)
exit(EXIT_FAILURE);
if (pid == 0)
exit(EXIT_SUCCESS);
if (wait(NULL) != pid)
exit(EXIT_FAILURE);
exit(EXIT_SUCCESS);
}
Since legacy clone() couldn't be extended this was not a problem so
far and nobody really noticed or cared since nothing in the kernel
ever bothered to look at the upper 32 bits.
But once we introduced clone3() and expanded the flag argument in
struct clone_args to 64 bit we opened this can of worms. With the
first flag-based extension to clone3() making use of the upper 32 bits
of the flag argument we've effectively made it possible for the legacy
clone() syscall to reach clone3() only flags on accident. The sign
extension scenario is just the odd corner-case that we needed to
figure this out.
The reason we just realized this now and not already when we
introduced CLONE_CLEAR_SIGHAND was that CLONE_INTO_CGROUP assumes that
a valid cgroup file descriptor has been given - whereas
CLONE_CLEAR_SIGHAND doesn't need to verify anything. It just silently
resets the signal handlers to SIG_DFL.
So the sign extension (or the user accidently passing garbage for the
upper 32 bits) caused the CLONE_INTO_CGROUP bit to be raised and the
kernel to error out when it didn't find a valid cgroup file
descriptor.
Note, I'm also capping kernel_thread()'s flag argument mainly because
none of the new features make sense for kernel_thread() and we
shouldn't risk them being accidently activated however unlikely. If we
wanted to, we could even make kernel_thread() yell when an unknown
flag has been set which it doesn't do right now. But it's not worth
risking this in a bugfix imho"
* tag 'for-linus-2020-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fork: prevent accidental access to clone3 features
Linus Torvalds [Thu, 14 May 2020 18:46:52 +0000 (11:46 -0700)]
Merge tag 'trace-v5.7-rc5' of git://git./linux/kernel/git/rostedt/linux-trace
Pull more tracing fixes from Steven Rostedt:
"Various tracing fixes:
- Fix a crash when having function tracing and function stack tracing
on the command line.
The ftrace trampolines are created as executable and read only. But
the stack tracer tries to modify them with text_poke() which
expects all kernel text to still be writable at boot. Keep the
trampolines writable at boot, and convert them to read-only with
the rest of the kernel.
- A selftest was triggering in the ring buffer iterator code, that is
no longer valid with the update of keeping the ring buffer writable
while a iterator is reading.
Just bail after three failed attempts to get an event and remove
the warning and disabling of the ring buffer.
- While modifying the ring buffer code, decided to remove all the
unnecessary BUG() calls"
* tag 'trace-v5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ring-buffer: Remove all BUG() calls
ring-buffer: Don't deactivate the ring buffer on failed iterator reads
x86/ftrace: Have ftrace trampolines turn read-only at the end of system boot up
Linus Torvalds [Thu, 14 May 2020 18:39:21 +0000 (11:39 -0700)]
Merge tag 'pm-5.7-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Prevent the suspend-to-idle internal loop from busy spinning after a
spurious ACPI SCI wakeup in some cases"
* tag 'pm-5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: EC: PM: Avoid premature returns from acpi_s2idle_wake()
Andrey Konovalov [Thu, 14 May 2020 00:50:54 +0000 (17:50 -0700)]
kasan: add missing functions declarations to kasan.h
KASAN is currently missing declarations for __asan_report* and __hwasan*
functions. This can lead to compiler warnings.
Reported-by: Leon Romanovsky <leon@kernel.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Leon Romanovsky <leon@kernel.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/r/45b445a76a79208918f0cc44bfabebaea909b54d.1589297433.git.andreyknvl@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Thu, 14 May 2020 00:50:51 +0000 (17:50 -0700)]
kasan: consistently disable debugging features
KASAN is incompatible with some kernel debugging/tracing features.
There's been multiple patches that disable those feature for some of
KASAN files one by one. Instead of prolonging that, disable these
features for all KASAN files at once.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Link: http://lkml.kernel.org/r/29bd753d5ff5596425905b0b07f51153e2345cc1.1589297433.git.andreyknvl@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vasily Averin [Thu, 14 May 2020 00:50:48 +0000 (17:50 -0700)]
ipc/util.c: sysvipc_find_ipc() incorrectly updates position index
Commit
89163f93c6f9 ("ipc/util.c: sysvipc_find_ipc() should increase
position index") is causing this bug (seen on 5.6.8):
# ipcs -q
------ Message Queues --------
key msqid owner perms used-bytes messages
# ipcmk -Q
Message queue id: 0
# ipcs -q
------ Message Queues --------
key msqid owner perms used-bytes messages
0x82db8127 0 root 644 0 0
# ipcmk -Q
Message queue id: 1
# ipcs -q
------ Message Queues --------
key msqid owner perms used-bytes messages
0x82db8127 0 root 644 0 0
0x76d1fb2a 1 root 644 0 0
# ipcrm -q 0
# ipcs -q
------ Message Queues --------
key msqid owner perms used-bytes messages
0x76d1fb2a 1 root 644 0 0
0x76d1fb2a 1 root 644 0 0
# ipcmk -Q
Message queue id: 2
# ipcrm -q 2
# ipcs -q
------ Message Queues --------
key msqid owner perms used-bytes messages
0x76d1fb2a 1 root 644 0 0
0x76d1fb2a 1 root 644 0 0
# ipcmk -Q
Message queue id: 3
# ipcrm -q 1
# ipcs -q
------ Message Queues --------
key msqid owner perms used-bytes messages
0x7c982867 3 root 644 0 0
0x7c982867 3 root 644 0 0
0x7c982867 3 root 644 0 0
0x7c982867 3 root 644 0 0
Whenever an IPC item with a low id is deleted, the items with higher ids
are duplicated, as if filling a hole.
new_pos should jump through hole of unused ids, pos can be updated
inside "for" cycle.
Fixes:
89163f93c6f9 ("ipc/util.c: sysvipc_find_ipc() should increase position index")
Reported-by: Andreas Schwab <schwab@suse.de>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Waiman Long <longman@redhat.com>
Cc: NeilBrown <neilb@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/4921fe9b-9385-a2b4-1dc4-1099be6d2e39@virtuozzo.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Brian Geffon [Thu, 14 May 2020 00:50:44 +0000 (17:50 -0700)]
userfaultfd: fix remap event with MREMAP_DONTUNMAP
A user is not required to set a new address when using MREMAP_DONTUNMAP
as it can be used without MREMAP_FIXED. When doing so the remap event
will use new_addr which may not have been set and we didn't propagate it
back other then in the return value of remap_to.
Because ret is always the new address it's probably more correct to use
it rather than new_addr on the remap_event_complete call, and it
resolves this bug.
Fixes:
e346b3813067d4b ("mm/mremap: add MREMAP_DONTUNMAP to mremap()")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Brian Geffon <bgeffon@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: "Michael S . Tsirkin" <mst@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Sonny Rao <sonnyrao@google.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Link: http://lkml.kernel.org/r/20200506172158.218366-1-bgeffon@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Thu, 14 May 2020 00:50:41 +0000 (17:50 -0700)]
mm/gup: fix fixup_user_fault() on multiple retries
This part was overlooked when reworking the gup code on multiple
retries.
When we get the 2nd+ retry, we'll be with TRIED flag set. Current code
will bail out on the 2nd retry because the !TRIED check will fail so the
retry logic will be skipped. What's worse is that, it will also return
zero which errornously hints the caller that the page is faulted in
while it's not.
The !TRIED flag check seems to not be needed even before the mutliple
retries change because if we get a VM_FAULT_RETRY, it must be the 1st
retry, and we should not have TRIED set for that.
Fix it by removing the !TRIED check, at the meantime check against fatal
signals properly before the page fault so we can still properly respond
to the user killing the process during retries.
Fixes:
4426e945df58 ("mm/gup: allow VM_FAULT_RETRY for multiple times")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Link: http://lkml.kernel.org/r/20200502003523.8204-1-peterx@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roman Penyaev [Thu, 14 May 2020 00:50:38 +0000 (17:50 -0700)]
epoll: call final ep_events_available() check under the lock
There is a possible race when ep_scan_ready_list() leaves ->rdllist and
->obflist empty for a short period of time although some events are
pending. It is quite likely that ep_events_available() observes empty
lists and goes to sleep.
Since commit
339ddb53d373 ("fs/epoll: remove unnecessary wakeups of
nested epoll") we are conservative in wakeups (there is only one place
for wakeup and this is ep_poll_callback()), thus ep_events_available()
must always observe correct state of two lists.
The easiest and correct way is to do the final check under the lock.
This does not impact the performance, since lock is taken anyway for
adding a wait entry to the wait queue.
The discussion of the problem can be found here:
https://lore.kernel.org/linux-fsdevel/
a2f22c3c-c25a-4bda-8339-
a7bdaf17849e@akamai.com/
In this patch barrierless __set_current_state() is used. This is safe
since waitqueue_active() is called under the same lock on wakeup side.
Short-circuit for fatal signals (i.e. fatal_signal_pending() check) is
moved to the line just before actual events harvesting routine. This is
fully compliant to what is said in the comment of the patch where the
actual fatal_signal_pending() check was added:
c257a340ede0 ("fs, epoll:
short circuit fetching events if thread has been killed").
Fixes:
339ddb53d373 ("fs/epoll: remove unnecessary wakeups of nested epoll")
Reported-by: Jason Baron <jbaron@akamai.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Roman Penyaev <rpenyaev@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Jason Baron <jbaron@akamai.com>
Cc: Khazhismel Kumykov <khazhy@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200505145609.1865152-1-rpenyaev@suse.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yafang Shao [Thu, 14 May 2020 00:50:34 +0000 (17:50 -0700)]
mm, memcg: fix inconsistent oom event behavior
A recent commit
9852ae3fe529 ("mm, memcg: consider subtrees in
memory.events") changed the behavior of memcg events, which will now
consider subtrees in memory.events.
But oom_kill event is a special one as it is used in both cgroup1 and
cgroup2. In cgroup1, it is displayed in memory.oom_control. The file
memory.oom_control is in both root memcg and non root memcg, that is
different with memory.event as it only in non-root memcg. That commit
is okay for cgroup2, but it is not okay for cgroup1 as it will cause
inconsistent behavior between root memcg and non-root memcg.
Here's an example on why this behavior is inconsistent in cgroup1.
root memcg
/
memcg foo
/
memcg bar
Suppose there's an oom_kill in memcg bar, then the oon_kill will be
root memcg : memory.oom_control(oom_kill) 0
/
memcg foo : memory.oom_control(oom_kill) 1
/
memcg bar : memory.oom_control(oom_kill) 1
For the non-root memcg, its memory.oom_control(oom_kill) includes its
descendants' oom_kill, but for root memcg, it doesn't include its
descendants' oom_kill. That means, memory.oom_control(oom_kill) has
different meanings in different memcgs. That is inconsistent. Then the
user has to know whether the memcg is root or not.
If we can't fully support it in cgroup1, for example by adding
memory.events.local into cgroup1 as well, then let's don't touch its
original behavior.
Fixes:
9852ae3fe529 ("mm, memcg: consider subtrees in memory.events")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Chris Down <chris@chrisdown.name>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200502141055.7378-1-laoar.shao@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Thu, 14 May 2020 16:05:33 +0000 (18:05 +0200)]
ALSA: hda/realtek - Limit int mic boost for Thinkpad T530
Lenovo Thinkpad T530 seems to have a sensitive internal mic capture
that needs to limit the mic boost like a few other Thinkpad models.
Although we may change the quirk for ALC269_FIXUP_LENOVO_DOCK, this
hits way too many other laptop models, so let's add a new fixup model
that limits the internal mic boost on top of the existing quirk and
apply to only T530.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1171293
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200514160533.10337-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Steven Rostedt (VMware) [Wed, 13 May 2020 19:36:22 +0000 (15:36 -0400)]
ring-buffer: Remove all BUG() calls
There's a lot of checks to make sure the ring buffer is working, and if an
anomaly is detected, it safely shuts itself down. But there's a few cases
that it will call BUG(), which defeats the point of being safe (it crashes
the kernel when an anomaly is found!). There's no reason for them. Switch
them all to either WARN_ON_ONCE() (when no ring buffer descriptor is present),
or to RB_WARN_ON() (when a ring buffer descriptor is present).
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Wed, 13 May 2020 19:18:01 +0000 (15:18 -0400)]
ring-buffer: Don't deactivate the ring buffer on failed iterator reads
If the function tracer is running and the trace file is read (which uses the
ring buffer iterator), the iterator can get in sync with the writes, and
caues it to fail to find a page with content it can read three times. This
causes a warning and deactivation of the ring buffer code.
Looking at the other cases of failure to get an event, it appears that
there's a chance that the writer could cause them too. Since the iterator is
a "best effort" to read the ring buffer if there's an active writer (the
consumer reader is made for this case "see trace_pipe"), if it fails to get
an event after three tries, simply give up and return NULL. Don't warn, nor
disable the ring buffer on this failure.
Link: https://lore.kernel.org/r/20200429090508.GG5770@shao2-debian
Reported-by: kernel test robot <lkp@intel.com>
Fixes:
ff84c50cfb4b ("ring-buffer: Do not die if rb_iter_peek() fails more than thrice")
Tested-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>