OSDN Git Service
Alvin Šipraga [Sat, 23 Apr 2022 12:08:53 +0000 (14:08 +0200)]
drm: bridge: adv7511: use non-legacy mode for CEC RX
The ADV7511 family of bridges supports two modes for CEC RX: legacy and
non-legacy mode. The only difference is whether the chip uses a single
CEC RX buffer, or uses all three available RX buffers. Currently the
adv7511 driver uses legacy mode.
While debugging a stall in CEC RX on an ADV7535, we reached out to
Analog Devices, who suggested to use non-legacy mode instead. According
to the programming guide for the ADV7511 [1], and the register control
manual of the ADV7535 [2], this is the default behaviour on reset. As
previously stated, the adv7511 driver currently overrides this to legacy
mode.
This patch updates the adv7511 driver to instead use non-legacy mode
with all three CEC RX buffers. As a result of this change, we no longer
experience any stalling of CEC RX with the ADV7535. It is not known why
non-legacy mode solves this particular issue, but besides this, no
functional change is to be expected by this patch. Please note that this
has only been tested on an ADV7535.
What follows is a brief description of the non-legacy mode interrupt
handling behaviour. The programming guide in [1] gives a more detailed
explanation.
With three RX buffers, the interrupt handler checks the CEC_RX_STATUS
register (renamed from CEC_RX_ENABLE in this patch), which contains
2-bit psuedo-timestamps for each of the RX buffers. The RX timestamps
for each buffer represent the time of arrival for the CEC frame held in
a given buffer, with lower timestamp values indicating chronologically
older frames. A special value of 0 indicates that the given RX buffer
is inactive and should be skipped. The interrupt handler parses these
timestamps and then reads the active RX buffers in the prescribed order
using the same logic as before. Changes have been made to ensure that
the correct RX buffer is cleared after processing. This clearing
procesure also sets the timestamp of the given RX buffer to 0 to mark it
as inactive.
[1] https://www.analog.com/media/en/technical-documentation/user-guides/ADV7511_Programming_Guide.pdf
cf. CEC Map, register 0x4A, bit 3, default value 1:
0 = Use only buffer 0 to store CEC frames (Legacy mode)
1 = Use all 3 buffers to stores the CEC frames (Non-legacy mode)
[2] The ADV7535 register control manual is under NDA, but trust me when
I say that non-legacy CEC RX mode is the default here too. Here the
register is offset by 0x70 and has an address of 0xBA in the DSI_CEC
regiser map.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220423120854.1503163-3-alvin@pqrs.dk
Alvin Šipraga [Sat, 23 Apr 2022 12:08:52 +0000 (14:08 +0200)]
drm: bridge: adv7511: enable CEC support for ADV7535
Like the ADV7533, the ADV7535 has an offset for the CEC register map,
and it is the same value (ADV7533_REG_CEC_OFFSET = 0x70).
Rather than testing for numerous chip types in the offset calculations
throughout the driver, just compute it during driver probe and put it in
the private adv7511 data structure.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220423120854.1503163-2-alvin@pqrs.dk
Pin-Yen Lin [Mon, 25 Apr 2022 13:44:24 +0000 (21:44 +0800)]
drm/bridge: it6505: Send DPCD SET_POWER to downstream
Send DPCD SET_POWER command to downstream in .atomic_disable to make the
downstream monitor enter the power down mode, so the device suspend won't
be affected.
Fixes:
b5c84a9edcd418 ("drm/bridge: add it6505 driver")
Signed-off-by: Pin-Yen Lin <treapking@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425134424.1150965-1-treapking@chromium.org
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Jagan Teki [Thu, 11 Nov 2021 09:41:03 +0000 (15:11 +0530)]
drm/panel: panel-simple: Fix proper bpc for AM-1280800N3TZQW-T00H
AM-1280800N3TZQW-T00H panel support 8 bpc not 6 bpc as per
recent testing in i.MX8MM platform.
Fix it.
Fixes:
bca684e69c4c ("drm/panel: simple: Add AM-1280800N3TZQW-T00H")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211111094103.494831-1-jagan@amarulasolutions.com
Christian König [Fri, 29 Apr 2022 11:36:16 +0000 (13:36 +0200)]
drm/nouveau: use drm_gem_plane_helper_prepare_fb
Instead of manually adjusting the plane state.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429134230.24334-3-christian.koenig@amd.com
Christian König [Thu, 21 Apr 2022 18:20:49 +0000 (20:20 +0200)]
drm: handle kernel fences in drm_gem_plane_helper_prepare_fb v2
drm_gem_plane_helper_prepare_fb() was using
drm_atomic_set_fence_for_plane() which ignores all implicit fences when an
explicit fence is already set. That's rather unfortunate when the fb still
has a kernel fence we need to wait for to avoid presenting garbage on the
screen.
So instead update the fence in the plane state directly. While at it also
take care of all potential GEM objects and not just the first one.
Also remove the now unused drm_atomic_set_fence_for_plane() function, new
drivers should probably use the atomic helpers directly.
v2: improve kerneldoc, use local variable and num_planes, WARN_ON_ONCE
on missing planes.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429134230.24334-1-christian.koenig@amd.com
Heiko Schocher [Fri, 29 Apr 2022 17:20:56 +0000 (14:20 -0300)]
drm/panel: simple: Add Startek KD070WVFPA043-C069A panel support
Add Startek KD070WVFPA043-C069A 7" TFT LCD panel support.
Signed-off-by: Heiko Schocher <hs@denx.de>
[fabio: passed .flags and .bus_flags]
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429172056.3499563-2-festevam@gmail.com
Fabio Estevam [Fri, 29 Apr 2022 17:20:55 +0000 (14:20 -0300)]
dt-bindings: display: simple: Add Startek KD070WVFPA043-C069A panel
Add Startek KD070WVFPA043-C069A 7" TFT LCD panel compatible string.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429172056.3499563-1-festevam@gmail.com
Minghao Chi [Fri, 29 Apr 2022 09:03:09 +0000 (09:03 +0000)]
drm/nouveau: simplify the return expression of nouveau_debugfs_init()
Simplify the return expression.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[fixed an indenting error before pushing]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429090309.3853003-1-chi.minghao@zte.com.cn
Minghao Chi [Fri, 29 Apr 2022 09:02:08 +0000 (09:02 +0000)]
drm/vc4: simplify the return expression of vc4_grab_bin_bo()
Simplify the return expression.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429090208.3852879-1-chi.minghao@zte.com.cn
Minghao Chi [Fri, 29 Apr 2022 05:49:45 +0000 (05:49 +0000)]
drm/vc4: simplify the return expression of vc4_prepare_fb()
Simplify the return expression.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429054945.3852039-1-chi.minghao@zte.com.cn
Dan Carpenter [Thu, 28 Apr 2022 12:26:23 +0000 (15:26 +0300)]
drm/sun4i: dsi: delete unnecessary IS_ERR() checks
The "dsi->bus_clk" pointer cannot be an error pointer at this point.
The check is confusing and unnecessary. Delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/YmqH71MtoGn2AXUg@kili
Marek Vasut [Thu, 28 Apr 2022 21:31:32 +0000 (23:31 +0200)]
drm/bridge: tc358767: Fix (e)DP bridge endpoint parsing in dedicated function
Per toshiba,tc358767.yaml DT binding document, port@2 the output (e)DP
port is optional. In case this port is not described in DT, the bridge
driver operates in DPI-to-DP mode. The drm_of_find_panel_or_bridge()
call in tc_probe_edp_bridge_endpoint() returns -ENODEV in case port@2
is not present in DT and this specific return value is incorrectly
propagated outside of tc_probe_edp_bridge_endpoint() function. All
other error values must be propagated and are propagated correctly.
Return 0 in case the port@2 is missing instead, that reinstates the
original behavior before the commit this patch fixes.
Fixes:
8478095a8c4b ("drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated function")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428213132.447890-1-marex@denx.de
Jani Nikula [Tue, 26 Apr 2022 09:19:13 +0000 (12:19 +0300)]
drm/edid: drop kernel-doc for static functions
Drop the kernel-doc for static functions, it's excessive, but retain the
info in plain comments.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426091913.1339941-2-jani.nikula@intel.com
Jani Nikula [Tue, 26 Apr 2022 09:19:12 +0000 (12:19 +0300)]
drm/edid: fix kernel-doc parameter name mismatches
Fix the below drm/edid kernel-doc warnings:
drivers/gpu/drm/drm_edid.c:1589: warning: Function parameter or member '_edid' not described in 'drm_edid_header_is_valid'
drivers/gpu/drm/drm_edid.c:1589: warning: Excess function parameter 'raw_edid' description in 'drm_edid_header_is_valid'
drivers/gpu/drm/drm_edid.c:1737: warning: Function parameter or member '_block' not described in 'drm_edid_block_valid'
drivers/gpu/drm/drm_edid.c:1737: warning: Excess function parameter 'raw_edid' description in 'drm_edid_block_valid'
drivers/gpu/drm/drm_edid.c:2136: warning: Function parameter or member 'read_block' not described in 'drm_do_get_edid'
drivers/gpu/drm/drm_edid.c:2136: warning: Function parameter or member 'context' not described in 'drm_do_get_edid'
drivers/gpu/drm/drm_edid.c:2136: warning: Excess function parameter 'get_edid_block' description in 'drm_do_get_edid'
drivers/gpu/drm/drm_edid.c:2136: warning: Excess function parameter 'data' description in 'drm_do_get_edid'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
References: https://lore.kernel.org/r/
20220406154431.
567414c3@canb.auug.org.au
References: https://lore.kernel.org/r/
20220420162431.
2b28ddea@canb.auug.org.au
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426091913.1339941-1-jani.nikula@intel.com
Javier Martinez Canillas [Thu, 28 Apr 2022 08:22:44 +0000 (10:22 +0200)]
drm/display: Select DP helper for DRM_DP_AUX_CHARDEV and DRM_DP_CEC
The DRM_DP_AUX_CHARDEV and DRM_DP_CEC Kconfig symbols enable code that use
DP helper functions, that are only present if CONFIG_DRM_DISPLAY_DP_HELPER
is also enabled.
But these don't select the DRM_DISPLAY_DP_HELPER symbol, meaning that it
is possible to enable any of them without CONFIG_DRM_DISPLAY_DP_HELPER.
That will lead to the following linking errors with the mentioned config:
LD vmlinux.o
MODPOST vmlinux.symvers
MODINFO modules.builtin.modinfo
GEN modules.builtin
LD .tmp_vmlinux.kallsyms1
KSYMS .tmp_vmlinux.kallsyms1.S
AS .tmp_vmlinux.kallsyms1.S
LD .tmp_vmlinux.kallsyms2
KSYMS .tmp_vmlinux.kallsyms2.S
AS .tmp_vmlinux.kallsyms2.S
LD vmlinux
SYSMAP System.map
SORTTAB vmlinux
OBJCOPY arch/arm64/boot/Image
MODPOST modules-only.symvers
ERROR: modpost: "drm_dp_dpcd_write" [drivers/gpu/drm/display/drm_display_helper.ko] undefined!
ERROR: modpost: "drm_dp_read_desc" [drivers/gpu/drm/display/drm_display_helper.ko] undefined!
ERROR: modpost: "drm_dp_dpcd_read" [drivers/gpu/drm/display/drm_display_helper.ko] undefined!
make[1]: *** [scripts/Makefile.modpost:134: modules-only.symvers] Error 1
make[1]: *** Deleting file 'modules-only.symvers'
make: *** [Makefile:1749: modules] Error 2
Besides making these symbols to select CONFIG_DRM_DISPLAY_DP_HELPER, make
them to depend on DRM_DISPLAY_HELPER, since can't be enabled without it.
Note: It seems this has been an issue for a long time but was made easier
to reproduce after the commit
1e0f66420b13 ("drm/display: Introduce a DRM
display-helper module"). Adding a Fixes: tag just to make sure that this
fix will be picked for stable once the mentioned change also lands there.
Fixes:
1e0f66420b13 ("drm/display: Introduce a DRM display-helper module")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428082244.390859-1-javierm@redhat.com
Wayne Lin [Thu, 28 Apr 2022 12:49:44 +0000 (20:49 +0800)]
drm/dp_mst: Lower down debug info level when receive NAK
[Why]
It's reasonable that we receive NAK while doing DP_REMOTE_DPCD_READ.
Downstream device might reply NAK with the reason and source should
react accordingly.
e.g.
1. When downstream device can't handle corresponding message in time,
it then replies NAK as reason been set as DEFER.
2. When multi-function branch-sink device doesn't enumerate virtual
DP peer devices for those multi-function down facing ports. Without
virtual DPCD, branch device might reply NAK with reason as BAD_PARAM
indicating this port can't do aux DPCD read.
It's expected result. Not an error.
[How]
Use drm_dbg_kms() to replace drm_err() when receive NAK.
Changes since v1:
* drm_dp_mst_topology.c file path changed. Folder was rename from
'dp' to 'display'
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[fixed some indenting issues]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428124944.1683680-1-Wayne.Lin@amd.com
Steven Price [Fri, 3 Dec 2021 10:28:15 +0000 (10:28 +0000)]
drm/plane: Move range check for format_count earlier
While the check for format_count > 64 in __drm_universal_plane_init()
shouldn't be hit (it's a WARN_ON), in its current position it will then
leak the plane->format_types array and fail to call
drm_mode_object_unregister() leaking the modeset identifier. Move it to
the start of the function to avoid allocating those resources in the
first place.
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/dri-devel/20211203102815.38624-1-steven.price@arm.com/
Miaoqian Lin [Mon, 13 Dec 2021 07:21:15 +0000 (07:21 +0000)]
malidp: Fix NULL vs IS_ERR() checking
The get_sg_table() function does not return NULL.
It returns error pointers.
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/dri-devel/20211213072115.18098-1-linmq006@gmail.com/
Thomas Zimmermann [Mon, 25 Apr 2022 07:59:39 +0000 (09:59 +0200)]
drm/format-helper: Add RGB565-to-XRGB8888 conversion
Add a format helper that converts RGB565 to XRGB8888. Use this
function in drm_fb_blit_toio(). Fixes simpledrm output for this
combination of formats.
UEFI and/or Grub will usually set 32-bit output in XRGB8888 format.
The issue can be reproduced by enabling simpledrm and requesting a
console framebuffer of different format on the kernel command line;
for example
nomodeset video=1024x768-16
In this case, conversion helpers will display nothing on the console.
The patch makes this work by implementing the rsp conversion helpers.
It also enables odd userspace configurations, such as running Xorg
with 16-bit color depth on a 32-bit output buffer.
v2:
* use helpers for struct drm_rect (Javier)
* improve commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425075939.30450-4-tzimmermann@suse.de
Thomas Zimmermann [Mon, 25 Apr 2022 07:59:38 +0000 (09:59 +0200)]
drm/format-helper: Add RGB888-to-XRGB8888 conversion
Add a format helper that converts RGB888 to XRGB8888. Use this
function in drm_fb_blit_toio(). Fixes simpledrm output for this
combination of formats.
UEFI and/or Grub will usually set 32-bit output in XRGB8888 format.
The issue can be reproduced by enabling simpledrm and requesting a
console framebuffer of different format on the kernel command line;
for example
nomodeset video=1024x768-24
In this case, conversion helpers will display nothing on the console.
The patch makes this work by implementing the rsp conversion helpers.
It also enables odd userspace configurations, such as running Xorg
with 24-bit color depth on a 32-bit output buffer.
v2:
* use helpers for struct drm_rect (Javier)
* improve commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425075939.30450-3-tzimmermann@suse.de
Thomas Zimmermann [Mon, 25 Apr 2022 07:59:37 +0000 (09:59 +0200)]
drm/format-helper: Print warning on missing format conversion
Not all possible format conversions are supported yet. Print a
warning on unsupported combinations.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425075939.30450-2-tzimmermann@suse.de
Chia-I Wu [Tue, 12 Apr 2022 20:48:09 +0000 (13:48 -0700)]
drm/sched: use __string in tracepoints
Otherwise, ring names are marked [UNSAFE-MEMORY].
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Cc: Rob Clark <robdclark@chromium.org>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220412204809.824491-2-olvaffe@gmail.com
Chia-I Wu [Tue, 12 Apr 2022 20:48:08 +0000 (13:48 -0700)]
drm/sched: use DECLARE_EVENT_CLASS
drm_sched_job and drm_run_job have the same prototype.
v2: rename the class from drm_sched_job_entity to drm_sched_job (Andrey)
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Cc: Rob Clark <robdclark@chromium.org>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220412204809.824491-1-olvaffe@gmail.com
Guo Zhengkui [Mon, 25 Apr 2022 11:47:00 +0000 (19:47 +0800)]
drm/nouveau/devinit/nva3-: fix returnvar.cocci warning
Fix the following coccicheck warning:
drivers/gpu/drm/nouveau/nvkm/subdev/devinit/gt215.c:71:5-12:
Unneeded variable: "disable". Return "0ULL" on line 85.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425114701.7182-1-guozhengkui@vivo.com
Tom Rix [Mon, 25 Apr 2022 13:13:08 +0000 (09:13 -0400)]
drm/nouveau/disp/gv100: make gv100_disp_wndw and gv100_disp_wndw_mthd static
Sparse reports these issues
wndwgv100.c:120:1: warning: symbol 'gv100_disp_wndw_mthd' was not declared. Should it be static?
wndwgv100.c:140:1: warning: symbol 'gv100_disp_wndw' was not declared. Should it be static?
These variable are only used in wndwgv100.c. Single file variables should be static.
So use static as their storage-class specifiers.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425131308.158635-1-trix@redhat.com
Tom Rix [Mon, 25 Apr 2022 13:00:50 +0000 (09:00 -0400)]
drm/nouveau/disp/gv100: make gv100_disp_wimm static
Sparse reports this issue
wimmgv100.c:39:1: warning: symbol 'gv100_disp_wimm' was not declared. Should it be static?
This variable is only used in wimmgv100.c. Single file variables should be static.
So use static as its storage-class specifier.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425130050.1643103-1-trix@redhat.com
Tom Rix [Fri, 22 Apr 2022 18:51:32 +0000 (14:51 -0400)]
drm/nouveau/kms/gv100: use static for gv100_disp_core_mthd_[base|sor]
Sparse reports these issues
coregv100.c:27:1: warning: symbol 'gv100_disp_core_mthd_base' was not declared. Should it be static?
coregv100.c:43:1: warning: symbol 'gv100_disp_core_mthd_sor' was not declared. Should it be static?
These variables are only used in coregv100.c. Single file use
variables should be static, so add static to their storage-class specifier.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422185132.3163248-1-trix@redhat.com
Colin Ian King [Sun, 24 Apr 2022 18:35:12 +0000 (19:35 +0100)]
drm/v3d: Fix null pointer dereference of pointer perfmon
In the unlikely event that pointer perfmon is null the WARN_ON return path
occurs after the pointer has already been deferenced. Fix this by only
dereferencing perfmon after it has been null checked.
Fixes:
26a4dc29b74a ("drm/v3d: Expose performance counters to userspace")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Juan A. Suarez <jasuarez@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424183512.1365683-1-colin.i.king@gmail.com
Samuel Holland [Sun, 24 Apr 2022 16:26:32 +0000 (11:26 -0500)]
drm/sun4i: Add compatible for D1 display engine
Now that the various blocks in the D1 display engine pipeline are
supported, we can enable the overall engine.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-15-samuel@sholland.org
Samuel Holland [Sun, 24 Apr 2022 16:26:31 +0000 (11:26 -0500)]
drm/sun4i: Add support for D1 TCONs
D1 has a TCON TOP, so its quirks are similar to those for the R40 TCONs.
While there are some register changes, the part of the TCON TV supported
by the driver matches the R40 quirks, so that quirks structure can be
reused. D1 has the first supported TCON LCD with a TCON TOP, so the TCON
LCD needs a new quirks structure.
D1's TCON LCD hardware supports LVDS; in fact it provides dual-link LVDS
from a single TCON. However, it comes with a brand new LVDS PHY. Since
this PHY has not been tested, leave out LVDS driver support for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-14-samuel@sholland.org
Samuel Holland [Sun, 24 Apr 2022 16:26:30 +0000 (11:26 -0500)]
drm/sun4i: Add support for D1 TCON TOP
D1 has a TCON TOP with TCON TV0 and DSI, but no TCON TV1. This puts the
DSI clock name at index 1 in clock-output-names. Support this by only
incrementing the index for clocks that are actually supported.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-13-samuel@sholland.org
Samuel Holland [Sun, 24 Apr 2022 16:26:29 +0000 (11:26 -0500)]
drm/sun4i: Add support for D1 mixers
D1 has a display engine with the usual pair of mixers, albeit with
relatively few layers. In fact, D1 appears to be the first SoC to have
a mixer without any UI layers. Add support for these new variants.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-12-samuel@sholland.org
Samuel Holland [Sun, 24 Apr 2022 16:26:28 +0000 (11:26 -0500)]
drm/sun4i: csc: Add support for the new MMIO layout
D1 changes the MMIO offsets for the CSC blocks in the first mixer. The
mixers' ccsc property is used as an index into the ccsc_base array. Use
an enumeration to describe this index, and add the new set of offsets.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-11-samuel@sholland.org
Samuel Holland [Sun, 24 Apr 2022 16:26:27 +0000 (11:26 -0500)]
drm/sun4i: Allow VI layers to be primary planes
D1's mixer 1 has no UI layers, only a single VI layer. That means the
mixer can only be used if the primary plane comes from this VI layer.
Add the code to handle this case.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-10-samuel@sholland.org
Jernej Skrabec [Sun, 24 Apr 2022 16:26:26 +0000 (11:26 -0500)]
sun4i/drm: sun8i: use mode_set engine callback
Newly introduced mode_set callback in engine structure is a much better
place for setting mixer output size and interlace mode for the following
reasons:
1. Aforementioned properties change only when mode changes, so it's
enough to be set only once per mode set. Currently it's done whenever
properties of primary plane are changed.
2. It's assumed that primary plane will always cover whole screen. While
this is true most of the time, it's not always. DE2/3 planes are
universal and mostly equal in functionality. There is no reason to
add artificial limitation to primary planes.
3. The current code only works for UI layers, but some mixers do not
have any UI layers.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
[Samuel: update commit message]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-9-samuel@sholland.org
Jernej Skrabec [Sun, 24 Apr 2022 16:26:25 +0000 (11:26 -0500)]
sun4i/drm: backend: use mode_set engine callback
Newly introduced mode_set callback in engine structure is a much better
place for setting backend output size and interlace mode for following
reasons:
1. Aforementioned properties change only when mode changes, so it's
enough to be set only once per mode set. Currently it's done whenever
properties of primary plane are changed.
2. It's assumed that primary plane will always cover whole screen. While
this is true most of the time, it's not always. Planes are universal.
There is no reason to add artificial limitation to primary plane.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
[Samuel: drop unused 'interlaced' variable]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-8-samuel@sholland.org
Jernej Skrabec [Sun, 24 Apr 2022 16:26:24 +0000 (11:26 -0500)]
sun4i/drm: engine: Add mode_set callback
This optional callback is useful for setting properties which depends
only on current mode. Such properties are width, height and interlaced
output.
These properties are currently set in update layer callback for primary
plane which is less than ideal. More about that in follow up patches,
which will migrate that code to this newly defined callback.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-7-samuel@sholland.org
Samuel Holland [Sun, 24 Apr 2022 16:26:23 +0000 (11:26 -0500)]
drm/sun4i: Allow building the driver on RISC-V
Allwinner D1 is a RISC-V SoC which contains a DE 2.0 engine. Let's
remove the dependency on a specific CPU architecture, so the driver can
be built wherever ARCH_SUNXI is selected.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-6-samuel@sholland.org
Samuel Holland [Sun, 24 Apr 2022 16:26:22 +0000 (11:26 -0500)]
drm/sun4i: hdmi: Use more portable I/O helpers
readsb/writesb are unavailable on some architectures. In preparation for
removing the Kconfig architecture dependency, switch to the equivalent
but more portable ioread/write8_rep helpers.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-5-samuel@sholland.org
Samuel Holland [Sun, 24 Apr 2022 16:26:20 +0000 (11:26 -0500)]
dt-bindings: display: Add D1 display engine compatibles
Allwinner D1 contains a display engine 2.0. It features two mixers, a
TCON TOP (with DSI and HDMI), one TCON LCD, and one TCON TV.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-3-samuel@sholland.org
Samuel Holland [Sun, 24 Apr 2022 16:26:19 +0000 (11:26 -0500)]
dt-bindings: display: Separate clock item lists by compatible
So far, the binding and driver have relied on the fact that the H6
clocks are both a prefix and a subset of the R40 clocks. This allows
them to share the clocks/clock-names items and the clock-output-names
order between the hardware variants.
However, the D1 hardware has TCON TV0 and DSI, but no TCON TV1. This
cannot be supported by the existing scheme because it puts a gap in the
middle of the item lists. To prepare for adding D1 support, use separate
lists for variants with different combinations of clocks.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-2-samuel@sholland.org
Dmitry Baryshkov [Tue, 26 Apr 2022 01:13:59 +0000 (04:13 +0300)]
drm/bridge: tc358762: drop connector field
The tc358762.connector field is unused. Remove it to save space.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426011359.2861224-1-dmitry.baryshkov@linaro.org
Uwe Kleine-König [Mon, 25 Apr 2022 19:23:06 +0000 (21:23 +0200)]
drm/ssd130x: Make ssd130x_remove() return void
This function returns zero unconditionally, so there isn't any benefit
of returning a value. Make it return void to be able to see at a glance
that the return value of ssd130x_i2c_remove() is always zero.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425192306.59800-1-u.kleine-koenig@pengutronix.de
Marek Vasut [Sun, 17 Apr 2022 02:10:11 +0000 (04:10 +0200)]
drm: mxsfb: Obtain bus flags from bridge state
In case the MXSFB is connected to a bridge, attempt to obtain bus flags
from that bridge state too. The bus flags may specify e.g. the DE signal
polarity.
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417021011.337066-1-marex@denx.de
Marek Vasut [Sun, 17 Apr 2022 02:08:00 +0000 (04:08 +0200)]
drm: mxsfb: Reorder mxsfb_crtc_mode_set_nofb()
Reorder mxsfb_crtc_mode_set_nofb() such that all functions which perform
register IO are called from one single location in this function. This is
a clean up. No functional change.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417020800.336675-4-marex@denx.de
Marek Vasut [Sun, 17 Apr 2022 02:07:59 +0000 (04:07 +0200)]
drm: mxsfb: Factor out mxsfb_set_mode()
Pull mode registers programming from mxsfb_enable_controller() into
dedicated function mxsfb_set_mode(). This is a clean up. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417020800.336675-3-marex@denx.de
Marek Vasut [Sun, 17 Apr 2022 02:07:58 +0000 (04:07 +0200)]
drm: mxsfb: Replace mxsfb_get_fb_paddr() with drm_fb_cma_get_gem_addr()
Replace mxsfb_get_fb_paddr() with drm_fb_cma_get_gem_addr() to correctly handle
FB offset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417020800.336675-2-marex@denx.de
Marek Vasut [Sun, 17 Apr 2022 02:07:57 +0000 (04:07 +0200)]
drm: mxsfb: Wrap FIFO reset and comments into mxsfb_reset_block()
Wrap FIFO reset and comments into mxsfb_reset_block(), this is a clean up.
No functional change.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220417020800.336675-1-marex@denx.de
Thomas Zimmermann [Thu, 21 Apr 2022 07:31:08 +0000 (09:31 +0200)]
drm/display: Move SCDC helpers into display-helper library
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-9-tzimmermann@suse.de
Thomas Zimmermann [Thu, 21 Apr 2022 07:31:07 +0000 (09:31 +0200)]
drm/display: Move HDMI helpers into display-helper module
Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.
The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.
Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.
v3:
* fix Kconfig dependencies (Javier)
v2:
* reduce HDMI helpers to avoid exporting functions (Jani)
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-8-tzimmermann@suse.de
Thomas Zimmermann [Thu, 21 Apr 2022 07:31:06 +0000 (09:31 +0200)]
drm/display: Move HDCP helpers into display-helper module
Move DRM's HDCP helper library into the display/ subdirectory and add
it to DRM's display helpers. Split the header file into core and helpers.
Update all affected drivers. No functional changes.
v3:
* fix Kconfig dependencies
v2:
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-7-tzimmermann@suse.de
Thomas Zimmermann [Thu, 21 Apr 2022 07:31:05 +0000 (09:31 +0200)]
drm/display: Move DSC header and helpers into display-helper module
DSC is the Display Stream Compression standard for DisplayPort. Move
the DSC code into display/ and split the header into files for protocol
core and DRM helpers. Adapt all users of the code. No functional
changes.
To avoid the proliferation of Kconfig options, DSC is part of DRM's
support for DisplayPort. If necessary, a new option could make DSC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-6-tzimmermann@suse.de
Thomas Zimmermann [Thu, 21 Apr 2022 07:31:04 +0000 (09:31 +0200)]
drm/display: Split DisplayPort header into core and helper
Move DisplayPort protocol constants and structures into the new
header drm_dp.h, which can be used by DRM core components. The
existing header drm_dp_helper.h now only contains helper code for
graphics drivers. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-5-tzimmermann@suse.de
Thomas Zimmermann [Thu, 21 Apr 2022 07:31:03 +0000 (09:31 +0200)]
drm/display: Introduce a DRM display-helper module
Replace the DP-helper module with a display-helper module. The
support for DisplayPort becomes an internal option that drivers
have to select. Update all related Kconfig and Makefile rules.
Besides the existing code for DisplayPort, the new module will
contain helpers for other video-output standards, such as HDMI.
Drivers will have to select their required video-output helpers.
Linking all display-related code into a single module avoids the
proliferation of small kernel modules.
The module parameters drm_dp_cec_unregister_delay, dp_aux_i2c_speed_khz,
and dp_aux_i2c_transfer_size are moving from the drm_dp_helper namespace
to drm_display_helper.
v2:
* mention module parameters in commit message (Javier)
* distiguish between display module and DP support in Kconfig
* update Makefile rules for DP helpers
* move Kconfig rules into separate file under display/
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-4-tzimmermann@suse.de
Thomas Zimmermann [Thu, 21 Apr 2022 07:31:02 +0000 (09:31 +0200)]
drm: Rename dp/ to display/
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
Thomas Zimmermann [Thu, 21 Apr 2022 07:31:01 +0000 (09:31 +0200)]
drm: Put related statements next to each other in Makefile
Give the Makefile a bit more structure by putting rules for core,
helpers, drivers, etc next to each other.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-2-tzimmermann@suse.de
Chunguang Xu [Fri, 22 Apr 2022 11:09:11 +0000 (19:09 +0800)]
drm/tilcdc: fix typos in comment
Fix typos in comment.
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Signed-off-by: Jyri Sarha <jyri.sarha@iki.fi>
Link: https://patchwork.freedesktop.org/patch/msgid/1650625751-32137-1-git-send-email-brookxu.cn@gmail.com
Marek Vasut [Wed, 6 Apr 2022 09:36:27 +0000 (11:36 +0200)]
drm/panel: simple: Add missing bus flags for Innolux G070Y2-L01
The DE signal is active high on this display, fill in the missing bus_flags.
This aligns panel_desc with its display_timing .
Fixes:
a5d2ade627dca ("drm/panel: simple: Add support for Innolux G070Y2-L01")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220406093627.18011-1-marex@denx.de
Marek Vasut [Mon, 11 Apr 2022 00:47:28 +0000 (02:47 +0200)]
drm/panel: lvds: Drop now redundant width-mm and height-mm check
The check for mandatory DT properties width-mm and height-mm is now
part of of_get_drm_panel_display_mode(), drop the redundant check
from this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411004728.68203-2-marex@denx.de
Marek Vasut [Mon, 11 Apr 2022 00:47:27 +0000 (02:47 +0200)]
drm/modes: Make width-mm/height-mm check in of_get_drm_panel_display_mode() mandatory
All users of this function require width-mm/height-mm DT property to be
present per their DT bindings, make width-mm/height-mm check mandatory.
It is generally a good idea to specify panel dimensions, so userspace
can configure e.g. scaling accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411004728.68203-1-marex@denx.de
Marek Vasut [Fri, 22 Apr 2022 10:22:42 +0000 (12:22 +0200)]
drm/panel: simple: Add DataImage FG040346DSSWBG04 panel support
Add DataImage FG040346DSSWBG04 4.3" 480x272 TFT LCD 24bit DPI panel
support.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422102242.18959-2-marex@denx.de
Marek Vasut [Fri, 22 Apr 2022 10:22:41 +0000 (12:22 +0200)]
dt-bindings: display: simple: Add DataImage FG040346DSSWBG04 compatible string
Add DataImage FG040346DSSWBG04 4.3" 480x272 TFT LCD 24bit DPI panel
compatible string.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422102242.18959-1-marex@denx.de
Zack Rusin [Fri, 22 Apr 2022 16:13:42 +0000 (12:13 -0400)]
drm/vmwgfx: Reserve fence slots on buffer objects in cotables
The buffer objects created by cotables were missing fence reservations.
They are created from vmw_validation_res_validate which makes them miss
the ttm_eu_reserve_buffers which is called from vmw_validation_bo_reserve.
Cotables are the only resources which create a buffer object in the
create callback so make sure the code also reserves the slots.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Co-developed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Fixes:
c8d4c18bfbc4 ("dma-buf/drivers: make reserving a shared slot mandatory v4")
Link: https://patchwork.freedesktop.org/patch/msgid/20220422161342.1142584-1-zack@kde.org
Tom Rix [Thu, 21 Apr 2022 13:30:28 +0000 (09:30 -0400)]
drm/nouveau/gsp: change gv100_gsp from global to static
Smatch reports this issue
gv100.c:46:1: warning: symbol 'gv100_gsp' was not declared. Should it be static?
gv100_gsp is only used in gv100.c so change its
storage-class specifier to static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421133028.724954-1-trix@redhat.com
Robert Foss [Thu, 21 Apr 2022 13:14:15 +0000 (15:14 +0200)]
drm/bridge: Fix it6505 Kconfig DRM_DP_AUX_BUS dependency
it6505 depends on DRM_DP_AUX_BUS, the kconfig for it6505 should
reflect this dependency using 'select'.
Fixes:
b5c84a9edcd4 ("drm/bridge: add it6505 driver")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421131415.1289469-1-robert.foss@linaro.org
Javier Martinez Canillas [Wed, 20 Apr 2022 07:24:11 +0000 (09:24 +0200)]
drm/doc: Add sections about tiny drivers and external refs to intro page
Learning about the DRM subsystem could be quite overwhelming for newcomers
but there are lots of useful talks, slides and articles available that can
help to understand the needed concepts and ease the learning curve.
There are also simple DRM drivers that can be used as example about how a
DRM driver should look like.
Add sections to the introduction page, that contains references to these.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420072411.15104-1-javierm@redhat.com
José Expósito [Thu, 21 Apr 2022 17:07:25 +0000 (19:07 +0200)]
drm/sun4i: hdmi: Replace drm_detect_hdmi_monitor() with is_hdmi
Once EDID is parsed, the monitor HDMI support information is available
through drm_display_info.is_hdmi.
This driver calls drm_detect_hdmi_monitor() to receive the same
information and stores its own cached value, which is less efficient.
Avoid calling drm_detect_hdmi_monitor() and use drm_display_info.is_hdmi
instead and also remove sun4i_hdmi.hdmi_monitor as it is no longer
necessary.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421170725.903361-6-jose.exposito89@gmail.com
kernel test robot [Thu, 21 Apr 2022 15:09:46 +0000 (23:09 +0800)]
drm: bridge: dw_hdmi: Audio: fix returnvar.cocci warnings
drivers/gpu/drm/bridge/synopsys/dw-hdmi-gp-audio.c:80:5-8: Unneeded variable: "ret". Return "0" on line 94
drivers/gpu/drm/bridge/synopsys/dw-hdmi-gp-audio.c:105:5-8: Unneeded variable: "ret". Return "0" on line 112
Remove unneeded variable used to store return value.
Generated by: scripts/coccinelle/misc/returnvar.cocci
CC: Sandor Yu <Sandor.yu@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YmFzutFV/iDyEQF2@dd18de969aa6
Yang Wang [Thu, 21 Apr 2022 12:34:42 +0000 (20:34 +0800)]
drm/ttm: use kvcalloc() instead of kvmalloc_array() in ttm_tt v2
simplify programming with existing functions.
v2 (chk): minimal coding style cleanup
Signed-off-by: Yang Wang <KevinYang.Wang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421123442.1834102-1-KevinYang.Wang@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Miaoqian Lin [Wed, 20 Apr 2022 01:16:40 +0000 (01:16 +0000)]
drm/bridge: Fix error handling in analogix_dp_probe
In the error handling path, the clk_prepare_enable() function
call should be balanced by a corresponding 'clk_disable_unprepare()'
call, as already done in the remove function.
Fixes:
3424e3a4f844 ("drm: bridge: analogix/dp: split exynos dp driver to bridge directory")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420011644.25730-1-linmq006@gmail.com
Christian König [Tue, 19 Apr 2022 13:55:10 +0000 (15:55 +0200)]
drm/amdgpu: remove pointless ttm_eu usage from DM
We just need to reserve one BO here, no need for using ttm_eu to reserve
multiple BOs.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419141915.122157-2-christian.koenig@amd.com
Christian König [Tue, 19 Apr 2022 13:09:01 +0000 (15:09 +0200)]
drm/amdgpu: remove pointless ttm_eu usage from vkms
We just need to reserve one BO here, no need for using ttm_eu to reserve
multiple BOs.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419141915.122157-1-christian.koenig@amd.com
José Expósito [Wed, 20 Apr 2022 11:45:00 +0000 (13:45 +0200)]
drm/vc4: hdmi: Remove vc4_hdmi_encoder
The vc4_hdmi_encoder struct was used exclusively to cache the value
returned by drm_detect_hdmi_monitor() in order to avoid calling it
multiple times.
Now that drm_detect_hdmi_monitor() has been replaced with
drm_display_info.is_hdmi, there is no need to have an extra struct.
Remove vc4_hdmi_encoder.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420114500.187664-3-jose.exposito89@gmail.com
José Expósito [Wed, 20 Apr 2022 11:44:59 +0000 (13:44 +0200)]
drm/vc4: hdmi: Replace drm_detect_hdmi_monitor() with is_hdmi
Once EDID is parsed, the monitor HDMI support information is cached in
drm_display_info.is_hdmi by drm_parse_hdmi_vsdb_video().
This driver calls drm_detect_hdmi_monitor() to receive the same
information and stores its own cached value in
vc4_hdmi_encoder.hdmi_monitor, which is less efficient.
Avoid calling drm_detect_hdmi_monitor() and use drm_display_info.is_hdmi
instead. This also allows to remove vc4_hdmi_encoder.hdmi_monitor.
drm_detect_hdmi_monitor() is called in vc4_hdmi_connector_detect() and
vc4_hdmi_connector_get_modes(). In both cases it is safe to rely on
drm_display_info.is_hdmi as shown by ftrace:
$ sudo trace-cmd record -p function_graph -l "vc4_hdmi_*" -l "drm_*"
vc4_hdmi_connector_detect:
vc4_hdmi_connector_detect() {
drm_get_edid() {
drm_connector_update_edid_property() {
drm_add_display_info() {
drm_reset_display_info();
drm_for_each_detailed_block.part.0();
drm_parse_cea_ext() {
drm_find_cea_extension();
drm_parse_hdmi_vsdb_video();
/* drm_display_info.is_hdmi is cached here */
}
}
}
}
/* drm_display_info.is_hdmi is used here */
}
vc4_hdmi_connector_get_modes:
vc4_hdmi_connector_get_modes() {
drm_get_edid() {
drm_connector_update_edid_property() {
drm_add_display_info() {
drm_reset_display_info();
drm_for_each_detailed_block.part.0();
drm_parse_cea_ext() {
drm_find_cea_extension();
drm_parse_hdmi_vsdb_video();
/* drm_display_info.is_hdmi is cached here */
}
}
}
}
/* drm_display_info.is_hdmi is used here */
drm_connector_update_edid_property();
}
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420114500.187664-2-jose.exposito89@gmail.com
Zack Rusin [Tue, 12 Apr 2022 03:35:26 +0000 (23:35 -0400)]
drm/radeon: Use TTM builtin resource manager debugfs code
Switch to using the TTM resource manager debugfs helpers. The
functionality is largely the same.
The TTM resource managers need to stay valid for as long as the
drm debugfs_root is valid.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-6-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Zack Rusin [Tue, 12 Apr 2022 03:35:25 +0000 (23:35 -0400)]
drm/qxl: Use TTM builtin resource manager debugfs code
Switch to using the TTM resource manager debugfs helpers. The
functionality is largely the same.
The TTM resource managers need to stay valid for as long as the
drm debugfs_root is valid.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: virtualization@lists.linux-foundation.org
Cc: spice-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-5-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Zack Rusin [Tue, 12 Apr 2022 03:35:24 +0000 (23:35 -0400)]
drm/amdgpu: Use TTM builtin resource manager debugfs code
Switch to using the TTM resource manager debugfs helpers. It's
exactly the same functionality but the debugfs code is shared with
other drivers.
The TTM resource managers need to stay valid for as long as the
drm debugfs_root is valid.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Nirmoy Das <nirmoy.das@amd.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: amd-gfx@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-4-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Zack Rusin [Tue, 12 Apr 2022 03:35:23 +0000 (23:35 -0400)]
drm/vmwgfx: Add debugfs entries for various ttm resource managers
Use the newly added TTM's ability to automatically create debugfs entries
for specified placements. This creates debugfs files that can be read to
get information about various TTM resource managers which are used by
vmwgfx.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-3-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Zack Rusin [Tue, 12 Apr 2022 03:35:22 +0000 (23:35 -0400)]
drm/ttm: Add common debugfs code for resource managers
Drivers duplicate the code required to add debugfs entries for various
ttm resource managers. To fix it add common TTM resource manager debugfs
code that each driver can reuse.
Specific resource managers can overwrite
ttm_resource_manager_func::debug to get more information from those
debugfs entries.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220412033526.369115-2-zack@kde.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Javier Martinez Canillas [Tue, 19 Apr 2022 21:48:23 +0000 (23:48 +0200)]
drm/solomon: Add SSD130x OLED displays SPI support
The ssd130x driver only provides the core support for these devices but it
does not have any bus transport logic. Add a driver to interface over SPI.
There is a difference in the communication protocol when using 4-wire SPI
instead of I2C. For the latter, a control byte that contains a D/C# field
has to be sent. This field tells the controller whether the data has to be
written to the command register or to the graphics display data memory.
But for 4-wire SPI that control byte is not used, instead a real D/C# line
must be pulled HIGH for commands data and LOW for graphics display data.
For this reason the standard SPI regmap can't be used and a custom .write
bus handler is needed.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-6-javierm@redhat.com
Javier Martinez Canillas [Tue, 19 Apr 2022 21:48:22 +0000 (23:48 +0200)]
drm/solomon: Move device info from ssd130x-i2c to the core driver
These are declared in the ssd130x-i2c transport driver but the information
is not I2C specific, and could be used by other SSD130x transport drivers.
Move them to the ssd130x core driver and just set the OF device entries to
an ID that could be used to lookup the correct device info from an array.
While being there, also move the SSD130X_DATA and SSD130X_COMMAND control
bytes. Since even though they are used by the I2C interface, they could
also be useful for other transport protocols such as SPI.
Suggested-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-5-javierm@redhat.com
Javier Martinez Canillas [Tue, 19 Apr 2022 21:48:21 +0000 (23:48 +0200)]
drm/solomon: Add ssd130x new compatible strings and deprecate old ones.
The current compatible strings for SSD130x I2C controllers contain an "fb"
and "-i2c" suffixes. These have been deprecated and more correct ones were
added, that don't encode a subsystem or bus used to interface the devices.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-4-javierm@redhat.com
Javier Martinez Canillas [Tue, 19 Apr 2022 21:48:20 +0000 (23:48 +0200)]
dt-bindings: display: ssd1307fb: Extend schema for SPI controllers
The Solomon SSD130x OLED displays can either have an I2C or SPI interface,
add to the schema the properties and examples for OLED devices under SPI.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-3-javierm@redhat.com
Javier Martinez Canillas [Tue, 19 Apr 2022 21:48:19 +0000 (23:48 +0200)]
dt-bindings: display: ssd1307fb: Deprecate "-i2c" compatible strings
The current compatible strings for SSD130x I2C controllers contain both an
"fb" and "-i2c" suffixes. It seems to indicate that are for a fbdev driver
and also that are for devices that can be accessed over an I2C bus.
But a DT is supposed to describe the hardware and not Linux implementation
details. So let's deprecate those compatible strings and add new ones that
only contain the vendor and device name, without any of these suffixes.
These will just describe the device and can be matched by both I2C and SPI
DRM drivers. The required properties should still be enforced for old ones.
While being there, just drop the "sinowealth,sh1106-i2c" compatible string
since that was never present in a released Linux version.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-2-javierm@redhat.com
Thomas Zimmermann [Tue, 19 Apr 2022 10:04:05 +0000 (12:04 +0200)]
fbdev: Warn in hot-unplug workaround for framebuffers without device
A workaround makes fbdev hot-unplugging work for framebuffers without
device. The only user for this feature was offb. As each OF framebuffer
now has an associated platform device, the workaround hould no longer
be triggered. Update it with a warning and rewrite the comment. Fbdev
drivers that trigger the hot-unplug workaround really need to be fixed.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Suggested-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419100405.12600-3-tzimmermann@suse.de
Thomas Zimmermann [Tue, 19 Apr 2022 10:04:04 +0000 (12:04 +0200)]
of: Create platform devices for OF framebuffers
Create a platform device for each OF-declared framebuffer and have
offb bind to these devices. Allows for real hot-unplugging and other
drivers besides offb.
Originally, offb created framebuffer devices while initializing its
module by parsing the OF device tree. No actual Linux device was set
up. This tied OF framebuffers to offb and makes writing other drivers
for the OF framebuffers complicated. The absence of a Linux device
further prevented real hot-unplugging. Adding a distinct platform
device for each OF framebuffer solves both problems. Specifically, a
DRM driver can now provide graphics output for modern userspace.
Some of the offb init code is now located in the OF initialization.
There's now also an implementation of of_platform_default_populate_init(),
which was missing before. The OF side creates different devices for
either OF display nodes or BootX displays as they require different
handling by the driver. The offb drivers picks up each type of device
and runs the appropriate fbdev initialization.
Tested with OF display nodes on qemu's ppc64le target.
v3:
* declare variable 'node' with function scope (Rob)
v2:
* run PPC code as part of existing initialization (Rob)
* add a few more error warnings (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419100405.12600-2-tzimmermann@suse.de
Xiaomeng Tong [Wed, 13 Apr 2022 05:11:05 +0000 (13:11 +0800)]
drm/gma500: fix a potential repeat execution in psb_driver_load
Instead of exiting the loop as expected when an entry is found, the
list_for_each_entry() continues until the traversal is complete. To
avoid potential executing 'ret = gma_backlight_init(dev);' repeatly,
goto outside the loop when found entry by replacing switch/case with
if statement.
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
[Fixed indentation]
Link: https://patchwork.freedesktop.org/patch/msgid/20220413051105.5612-1-xiam0nd.tong@gmail.com
Marek Vasut [Thu, 7 Apr 2022 18:56:17 +0000 (20:56 +0200)]
drm: bridge: icn6211: Add DSI lane count DT property parsing
The driver currently hard-codes DSI lane count to two, however the chip
is capable of operating in 1..4 DSI lanes mode. Parse 'data-lanes' DT
property and program the result into DSI_CTRL register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407185617.179573-2-marex@denx.de
Marek Vasut [Thu, 7 Apr 2022 18:56:16 +0000 (20:56 +0200)]
dt-bindings: display: bridge: icn6211: Document DSI data-lanes property
It is necessary to specify the number of connected/used DSI data lanes when
using the DSI input port of this bridge. Document the 'data-lanes' property
of the DSI input port.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407185617.179573-1-marex@denx.de
Nícolas F. R. A. Prado [Fri, 8 Apr 2022 01:30:34 +0000 (21:30 -0400)]
drm/bridge: anx7625: Use uint8 for lane-swing arrays
As defined in the anx7625 dt-binding, the analogix,lane0-swing and
analogix,lane1-swing properties are uint8 arrays. Yet, the driver was
reading the array as if it were of uint32 and masking to 8-bit before
writing to the registers. This means that a devicetree written in
accordance to the dt-binding would have its values incorrectly parsed.
Fix the issue by reading the array as uint8 and storing them as uint8
internally, so that we can also drop the masking when writing the
registers.
Fixes:
fd0310b6fe7d ("drm/bridge: anx7625: add MIPI DPI input feature")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220408013034.673418-1-nfraprado@collabora.com
Sandor Yu [Fri, 15 Apr 2022 02:42:50 +0000 (10:42 +0800)]
drm: bridge: dw_hdmi: Audio: Add General Parallel Audio (GPA) driver
General Parallel Audio (GPA) interface is one of the supported
audio interface for synopsys HDMI module, which has verified for
i.MX8MPlus platform.
This is initial version for GPA.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/f21ba3e8c4d9d028ac74c6f3c588ddbffe739399.1649989179.git.Sandor.yu@nxp.com
Sandor Yu [Fri, 15 Apr 2022 02:42:49 +0000 (10:42 +0800)]
drm: bridge: dw_hdmi: add reset function for PHY GEN1
PHY reset register(MC_PHYRSTZ) active high reset control for PHY GEN2,
and active low reset control for PHY GEN1.
Rename function dw_hdmi_phy_reset to dw_hdmi_phy_gen2_reset.
Add dw_hdmi_phy_gen1_reset function for PHY GEN1.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e0b3be2d63fe3e95246fb8b8b0dcd57415b29e04.1649989179.git.Sandor.yu@nxp.com
Sandor Yu [Fri, 15 Apr 2022 02:42:48 +0000 (10:42 +0800)]
drm: bridge: dw_hdmi: Enable GCP only for Deep Color
HDMI1.4b specification section 6.5.3:
Source shall only send GCPs with non-zero CD to sinks
that indicate support for Deep Color.
DW HDMI GCP default enabled, but only transmit CD
and do not handle AVMUTE, PP norDefault_Phase (yet).
Disable Auto GCP when 24-bit color for sinks that not support Deep Color.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/78fa41e4fb3d3d53354034bc221fcf870dbac617.1649989179.git.Sandor.yu@nxp.com
Sandor Yu [Fri, 15 Apr 2022 02:42:47 +0000 (10:42 +0800)]
drm: bridge: dw_hdmi: default enable workaround to clear the overflow
i.MX8MPlus (v2.13a) has verified need the workaround to clear the
overflow with one iteration.
Only i.MX6Q(v1.30a) need the workaround with 4 iterations,
the others versions later than v1.3a have been identified as needing
the workaround with a single iteration.
Default enable the workaround with one iteration for all versions
later than v1.30a.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/561951005a85574dcdd108e5d6a3a87df930ea3d.1649989179.git.Sandor.yu@nxp.com
Marek Szyprowski [Tue, 19 Apr 2022 09:14:22 +0000 (11:14 +0200)]
drm: bridge: panel: Register connector if DRM device is already registered
If panel_bridge_attach() happens after DRM device registration, the
created connector will not be registered by the DRM core anymore. Fix
this by registering it explicitly in such case.
This fixes the following issue observed on Samsung Exynos4210-based Trats
board with a DSI panel (the panel driver is registered after the Exynos DRM
component device is bound):
$ ./modetest -c -Mexynos
could not get connector 56: No such file or directory
Segmentation fault
While touching this, move the connector reset() call also under the DRM
device registered check, because otherwise it is not really needed.
Fixes:
934aef885f9d ("drm: bridge: panel: Reset the connector state pointer")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419091422.4255-1-m.szyprowski@samsung.com
Biju Das [Tue, 19 Apr 2022 14:24:53 +0000 (15:24 +0100)]
drm: bridge: adv7511: Enable DRM_BRIDGE_OP_HPD based on HPD interrupt
Connector detection using poll method won't work in case of bridge
attached to the encoder with the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR, as
the code defaults to HPD.
Enable DRM_BRIDGE_OP_HPD based on HPD interrupt availability, so that
it will fall back to polling, if HPD is not available.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419142453.48839-1-biju.das.jz@bp.renesas.com
Marek Vasut [Tue, 19 Apr 2022 14:39:58 +0000 (16:39 +0200)]
drm/bridge: lt9211: Add Lontium LT9211 bridge driver
Add driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.
This driver is written without any documentation from Lontium and based
only on shreds of information available in various obscure example codes,
hence long runs of unknown register patches and lengthy delays in various
places. Whichever register meaning could be divined from its behavior has
at least a comment around it.
Currently the only mode tested is Single-link DSI to Single-link LVDS.
Dual-link LVDS might work as well, the register programming is in place,
but is untested.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-2-marex@denx.de
Marek Vasut [Tue, 19 Apr 2022 14:39:57 +0000 (16:39 +0200)]
dt-bindings: display: bridge: lt9211: Add Lontium LT9211 bridge driver
Add bindings for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-1-marex@denx.de
Hsin-Yi Wang [Thu, 14 Apr 2022 09:00:04 +0000 (17:00 +0800)]
drm/bridge: anx7625: Fill in empty ELD when no connector
Speaker may share I2S with DP and .get_eld callback will be called when
speaker is playing. When HDMI wans't connected, the connector will be
null. Instead of return an error, fill in empty ELD.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414090003.1806535-1-hsinyi@chromium.org