OSDN Git Service
Helmut Schaa [Sun, 11 Jul 2010 10:29:26 +0000 (12:29 +0200)]
rt2x00: Remove set_tim callback from PCI drivers
Using the set_tim callback without managing the DTIM count and the
broad- and multicast buffering in hw, fw or the driver results in wrong
DTIM count values being sent out in beacons. Since all PCI drivers
fetch new beacons periodically and hence get an updated TIM we can just
remove the set_tim callback from these.
The rt2x00 USB drivers don't update the beacon periodically and thus
rely on the set_tim callback to get a correct TIM for beacon
transmission. USB devices still suffer from the DTIM count being wrong
under some circumstances but removing the set_tim callback from these
would cause more harm then good.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sun, 11 Jul 2010 10:28:54 +0000 (12:28 +0200)]
rt2x00: Use separate mac80211_ops for rt2800pci and rt2800usb
Use separate mac80211_ops for rt2800pci and rt2800usb in preparation
for further fixes. This shouldn't introduce functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sun, 11 Jul 2010 10:28:23 +0000 (12:28 +0200)]
rt2x00: Use pretbtt irq for fetching beacons on rt2800pci
Updating the beacon on pre tbtt instead of beacondone allows much lower
latency in regard to TIM updates. Hence, use the pre tbtt interrupt for
updating the beacon in rt2800pci (older devices don't provide a pre tbtt
interrupt).
Also, add a new driver flag to indicate if a driver has pre tbtt support
or not and implement the according behavior in rt2x00lib.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sun, 11 Jul 2010 10:27:58 +0000 (12:27 +0200)]
rt2x00: Implement broad- and multicast buffering
Although mac80211 buffers broad- and mutlicast frames for us in AP mode
we still have to send them out after a DTIM beacon. Implement this
behavior by sending out the buffered frames when the beacondone
interrupt is processed.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sun, 11 Jul 2010 10:27:26 +0000 (12:27 +0200)]
rt2x00: Allow beacon update without scheduling a work
Since all rt2x00 PCI drivers use threaded interrupts now we don't need
to schedule a work just to update the beacon. The only place where the
beacon still gets updated in atomic context is from the set_tim
callback. Hence, move the work scheduling there.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sun, 11 Jul 2010 10:26:48 +0000 (12:26 +0200)]
rt2x00: Convert rt2x00 to use threaded interrupts
Use threaded interrupts for all rt2x00 PCI devices.
This has several generic advantages:
- Reduce the time we spend in hard irq context
- Use non-atmic mac80211 functions for rx/tx
Furthermore implementing broad- and multicast buffering will be
much easier in process context while maintaining low latency and
updating the beacon just before transmission (pre tbtt interrupt)
can also be done in process context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 11 Jul 2010 10:26:12 +0000 (12:26 +0200)]
rt2x00: Make rt2800_write_beacon only export to GPL
rt2800_write_beacon is the only function which uses
EXPORT_SYMBOL instead of EXPORT_SYMBOL_GPL. All symbols
in rt2x00 should however use the GPL restricted export.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 11 Jul 2010 10:25:46 +0000 (12:25 +0200)]
rt2x00: Implement watchdog monitoring
Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 11 Jul 2010 10:25:17 +0000 (12:25 +0200)]
rt2x00: Fix vgc_level_reg handling
Currently vgc_level_reg and vgc_level are equal to eachother,
while the purpose of vgc_level_reg is the value last written
to the register and is remembered through link tuning resets.
The vgc_level is the currently active level, which is
reset during link tuning resets.
The usage of these variables depends on the drivers, some drivers
need both, while others need only one of the two.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 11 Jul 2010 10:24:47 +0000 (12:24 +0200)]
rt2x00: Disable link tuning while scanning
While scanning the link tuner must be disabled. Otherwise
it will interfere with receiving all beacons for each channel
due to changing sensitivity levels.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 11 Jul 2010 10:24:22 +0000 (12:24 +0200)]
rt2x00: Rename CONFIG_DISABLE_LINK_TUNING
Rename CONFIG_DISABLE_LINK_TUNING to DRIVER_SUPPORT_LINK_TUNING
Link tuning support is not only based on EEPROM decisions, but
also if the device actually supports it.
Currently only rt2500usb doesn't support link tuning because
of hardware problems. But rt2800usb is also suspected of having
problems with link tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 11 Jul 2010 10:23:50 +0000 (12:23 +0200)]
rt2x00: Convert AGC value from descriptor to RSSI (dBm)
The RSSI values in the RXWI descriptor aren't true RSSI
values. Instead they are more like the AGC values similar
to rt61pci. And as such, it needs the same conversion
before it can be passed to rt2x00lib/mac80211.
This requires the struct queue_entry to be passed to
rt2800_process_rxwi rather then the skb structure which
is contained in the queue_entry. This is required to
obtain the lna_gain information from the rt2x00_dev structure.
This fixes connection problems when using wpa_supplicant
which would try to connect to the worst AP's rather then the
best ones.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sun, 11 Jul 2010 10:23:09 +0000 (12:23 +0200)]
rt2x00: Limit txpower by eeprom values
Limit the txpower per rate by the approriate values in the eeprom.
This avoids too high txpower values resulting in bad tx performance.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 10 Jul 2010 22:10:42 +0000 (00:10 +0200)]
hostap: fixup strlen() math
In hostap_add_interface() we do:
sprintf(dev->name, "%s%s", prefix, name);
dev->name has IFNAMSIZ (16) characters.
prefix is local->dev->name.
name is "wds%d"
strlen() returns the number of characters in the string not counting the
NULL so if we have a string with 11 characters we get "12345678901wds%d"
which is 16 characters and a NULL so we're past the end of the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kulikov Vasiliy [Sat, 10 Jul 2010 12:28:57 +0000 (16:28 +0400)]
adm8211: fix memory leak
We must free priv->eeprom allocated in adm8211_read_eeprom().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 10 Jul 2010 08:53:38 +0000 (10:53 +0200)]
prism54: call BUG_ON() earlier
This test is off by one because strlen() doesn't include the NULL
terminator.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Fri, 9 Jul 2010 11:10:58 +0000 (14:10 +0300)]
wl1271: use __packed annotation
This patch changes __attribute__ ((packed)) annotations to __packed in wl1271
code that was introduced in a recent patch in wireless-testing.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Thu, 8 Jul 2010 01:13:48 +0000 (06:43 +0530)]
libertas: Added support for host sleep feature
Existing "ethtool -s ethX wol X" command configures hostsleep
parameters, but those are activated only during suspend/resume,
there is no way to configure host sleep without actual suspend.
This patch adds debugfs command to enable/disable host sleep based on
already configured host sleep parameters using wol command.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 12 Jul 2010 12:46:43 +0000 (14:46 +0200)]
cfg80211: ignore spurious deauth
Ever since mac80211/drivers are no longer
fully in charge of keeping track of the
auth status, trying to make them do so will
fail. Instead of warning and reporting the
deauthentication to userspace, cfg80211 must
simply ignore it so that spurious
deauthentications, e.g. before starting
authentication, aren't seen by userspace as
actual deauthentications.
Cc: stable@kernel.org
Reported-by: Paul Stewart <pstew@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 12 Jul 2010 20:03:07 +0000 (16:03 -0400)]
MAINTAINERS: mark adm8211 as an orphan
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Tue, 29 Jun 2010 18:29:49 +0000 (11:29 -0700)]
iwlagn: fix the bit mask of a FH register in stop Tx DMA flow
When we stop the Tx DMA channels, we poll bits 16:31 in
FH_TSSR_RX_STATUS_REG. From 4965 and up, only the bits 16:26 are legal.
Bits 27:31 are not used and are always unset.
Polling them will lead to fail on timeout but since the timeout is quite
small, the stall was not felt.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Thu, 1 Jul 2010 23:45:58 +0000 (16:45 -0700)]
iwlagn: more generic description for iwlagn devices
Intel Wireless WiFi Next Gen AGN support two major categories:
1. Intel Wireless WiFi 4965 AGN device
2. Intel Wireless-N/Advanced-N/Ultimate-N family
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Jay Sternberg [Fri, 2 Jul 2010 22:49:10 +0000 (15:49 -0700)]
iwlwifi: correct descriptions of advanced ucode errors
ucode errors were redefined in new ucode images and all new errors
were showing as advanced sysasserts which was misleading. new errors
are not sequential so additional lookup table added. errors do not
overlap so both are used to support older and newer ucode images.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Shanyu Zhao [Wed, 30 Jun 2010 00:27:27 +0000 (17:27 -0700)]
iwlwifi: enable 6050 series Gen2 devices
To enable 6050 series Gen 2 devices:
1) new PCI_IDs are added;
2) new EEPROM version and calibration version numbers defined;
3) new hardware REV number defined;
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Luciano Coelho [Thu, 8 Jul 2010 14:50:08 +0000 (17:50 +0300)]
wl1271: use per-channel max tx power passed by mac80211 when scanning
We were always using the max transmit power when scanning. Now we use the
values passed to the driver by the mac80211 stack, so that we comply with
regulations.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Thu, 8 Jul 2010 14:50:07 +0000 (17:50 +0300)]
wl1271: rewritten scanning code
This patch is a complete rewrite of the scanning code. It now includes a
state machine to scan all four possible sets of channels independently:
2.4GHz active, 2.4GHz passive, 5GHz active and 5GHz passive. The wl1271
firmware doesn't allow these sets to be mixed, so up to several scan commands
have to be issued. This patch also allows scanning more than 24 channels per
set, by breaking the sets into smaller parts if needed (the firmware can scan
a maximum of 24 channels at a time).
Previously, the scanning code was erroneously scanning all channels possible
actively, not complying with the CRDA values. This is also fixed with this
patch.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Thu, 8 Jul 2010 14:50:06 +0000 (17:50 +0300)]
wl1271: moved scan operations to a separate file
The scanning code is going to get a bit more complex, with proper support for
active/passive scans together with 2.4GHz and 5GHz. In the future, also a
new type of scan (periodic scan) will be added. When all this is
implemented, the code is going to be much more complex, so we'd better
separate it into a separate file.
This patch doesn't have any impact on functionality.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 8 Jul 2010 14:50:05 +0000 (17:50 +0300)]
wl1271: Update interface to temporarily disable dynamic PS
The mac80211 interface to temporarily disable dynamic PS changed, make
corresponding changes to the driver.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 8 Jul 2010 14:50:04 +0000 (17:50 +0300)]
wl1271: Fix warning when disconnecting and ad-hoc network
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 8 Jul 2010 14:50:03 +0000 (17:50 +0300)]
wl1271: Disable dynamic PS based on BT co-ext sense events
This patch requests mac80211 to disable dynamic PSM based on sense events
coming from the firmware. Effectively, whenever there is bluetooth traffic,
the mac80211 is forced into full PSM mode.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 8 Jul 2010 14:50:02 +0000 (17:50 +0300)]
wl1271: Update hardware ARP filtering configuration handling
The interface for hardware ARP configuration changed in the mac80211. Change
driver accordingly.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Thu, 8 Jul 2010 14:50:01 +0000 (17:50 +0300)]
wl1271: read fem manufacturer value from nvs
We should read the fem manufacturer value from the NVS, so we can modify it
easily and use a consistent value throughout the configuration. Previously
we had to set the FEM value in the NVS and in the driver's initialization
parameters. This patch removes the latter.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 8 Jul 2010 14:50:00 +0000 (17:50 +0300)]
wl1271: Work around AP's with broken ps-poll functionality
Some AP's (such as Zyxel Prestige 600) have totally broken ps-poll
functionality. When powersave is enabled, these AP's will set the TIM bit for
a STA in beacons, but when the STA responds with a ps-poll, the AP does not
respond with data.
The wl1271 firmware is able to send an indication to the host, when this
problem occurs. This patch adds implementation, which temporarily disables
power-save in response to this indication, allowing the AP to transmit whatever
data it has buffered for the STA / whatever data is inbound at that time.
This patch does not make these AP's work reliably in PSM, but improves the
chances of inbound data getting through.
The side effect of this patch is increased power consumption when using a
faulty AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 8 Jul 2010 14:49:59 +0000 (17:49 +0300)]
wl1271: Use all basic rates for ps-poll, instead of just the slowest
This improves ps-poll handling in WLAN PSM. It also improves performance,
including WLAN-BT co-existence reliability.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 8 Jul 2010 14:49:58 +0000 (17:49 +0300)]
wl1271: Use the ARP configuration function from mac80211
This patch updates the driver to use the ARP configuration function from the
mac80211. Also, clean up IPv6 support from the ACX function as ARP is not
used with that protocol version.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 8 Jul 2010 14:49:57 +0000 (17:49 +0300)]
wl1271: Add TSF handling
Add functionality to pass the current TSF (mac time) to the mac80211. This is
needed for ad-hoc merging.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 8 Jul 2010 14:49:56 +0000 (17:49 +0300)]
wl1271: Remove calibration from join command
This patch removes the calibration performed on the first join command. The
reasoning is that this is unnecessary as devices get their calibration data
via the NVS file, and because the commands break BT coexistence.
This is actually safe, because of the implementation the calibration
was executed on the first JOIN anyway, after an ifdown/ifup the devices have
relied on the NVS for calibration anyway (== most of the time.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 7 Jul 2010 19:07:49 +0000 (15:07 -0400)]
mac80211: remove wep dependency
The current mac80211 code assumes that WEP is always available. If WEP
fails to initialize, ieee80211_register_hw will always fail.
In some cases (e.g. FIPS certification), the cryptography used by WEP is
unavailable. However, in such cases there is no good reason why CCMP
encryption (or even no link level encryption) cannot be used. So, this
patch removes mac80211's assumption that WEP (and TKIP) will always be
available for use.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 7 Jul 2010 17:42:09 +0000 (19:42 +0200)]
ath9k: fix a buffer leak in A-MPDU completion
When ath_tx_complete_aggr() is called, it's responsible for returning
all buffers in the linked list. This was not done when the STA lookup
failed, leading to a race condition that could leak a few buffers when
a STA just disconnected.
Fix this by immediately returning all buffers to the free list in this case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 7 Jul 2010 17:42:08 +0000 (19:42 +0200)]
ath9k: fix a potential buffer leak in the STA teardown path
It looks like it might be possible for a TID to be paused, while still
holding some queued buffers, however ath_tx_node_cleanup currently only
iterates over active TIDs.
Fix this by always checking every allocated TID for the STA that is being
cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jiri Slaby [Wed, 7 Jul 2010 13:02:46 +0000 (15:02 +0200)]
NET: nl80211, fix lock imbalance and netdev referencing
Stanse found that nl80211_set_wiphy imporperly handles a lock and netdev
reference and contains unreachable code. It is because there return statement
isntead of assignment to result variable. Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jouni Malinen <j@w1.fi>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ameya Palande [Mon, 5 Jul 2010 14:12:38 +0000 (17:12 +0300)]
wl12xx: Use MODULE_ALIAS macro at correct postion for SPI bus
(Changed title, was "wl1251: Use MODULE_ALIAS macro at correct postion
for SPI bus". -- JWL)
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 6 Jul 2010 18:19:01 +0000 (14:19 -0400)]
Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6
Wey-Yi Guy [Mon, 28 Jun 2010 20:05:17 +0000 (13:05 -0700)]
iwlwifi: adding enhance sensitivity table entries
For newer devices (6000g2a and 6000g2b), the sensitivity table send to
uCode require additional table entries to help sensitivity calibration.
All the additional entries has fix data for now, but do expect the value
will be change in the future when device become more stable.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Thu, 24 Jun 2010 21:08:05 +0000 (14:08 -0700)]
iwlwifi: generic parameter define for _agn device
Code clean up to change name from having 5000 as part of name which easy
to confuse and think it is for 5000 series devices to more
generic _agn name since it is being used by multiple _agn devices.
No functional changes.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Thu, 24 Jun 2010 20:18:36 +0000 (13:18 -0700)]
iwlwifi: debugfs file for txfifo command testing
Add debugfs file for REPLY_TXFIFO_FLUSH host command testing.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Thu, 24 Jun 2010 20:18:35 +0000 (13:18 -0700)]
iwlwifi: add support for device tx flush request
"Flush" request can come from two different sources, it can either from
mac80211, or from device when the operation is needed. Here
adding the support for device issue "flush" request.
When receive tx complete with status is TX_STATUS_FAIL_RFKILL_FLUSH,
issue REPLY_TXFIFO_FLUSH command to uCode to flush out all the tx frames
in queues.
In this condition, since mac80211 has no knowledge of "flush" operation,
driver need to stop all the tx queues and wait for the operation
completed before wake up the queues for frames transmission.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Thu, 24 Jun 2010 20:22:36 +0000 (13:22 -0700)]
iwlwifi: add mac80211 flush callback support
Adding flush callback support in the driver. Two type of flush can be
issued by mac80211:
1. drop = true: frame drop is ok, issue REPLY_TXFIFO_FLUSH host command
to uCode to drop all the frames in tx fifo queues; then return the
control back to mac80211
2. drop = false: wait for either all the frames in tx fifo queues been
transmitted, or timeout; then return the control back to mac80211
If the flush request coming from mac80211, mac80211 will make sure there
are no additional frames push down to driver before flush operation is
completed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Thu, 24 Jun 2010 20:18:33 +0000 (13:18 -0700)]
iwlwifi: tx fifo queue flush command
Add host command and structure for tx fifo queue flush
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Tue, 22 Jun 2010 21:31:45 +0000 (14:31 -0700)]
iwlwifi: add debug print for parsing firmware TLV
When parsing TLV during loading firmware, if encounter any TLV error,
log the error message to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Mon, 21 Jun 2010 23:52:55 +0000 (16:52 -0700)]
iwlwifi: fix fw_restart module parameter
fw_restart module parameter was broken by the recent check for stuck
queue patch, driver check the fx_restart module parameter
before reload the firmware; but the stuck queue timer kick in after
firmware error and reload the firmware even fw_restart=0. In this case,
driver should not reload the firmware, it is important to help debugging
uCode error.
The only case we can ignore the module parameter is when user request
firmware reload from debugfs, which can bypass the checking and perform
firmware reload all the time.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Ming Lei [Thu, 1 Jul 2010 15:19:50 +0000 (23:19 +0800)]
minstrel_ht: fix check for downgrading of top2 rate
The check should be against current top2 rate, instead of
current top rate.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ming Lei [Thu, 1 Jul 2010 15:18:42 +0000 (23:18 +0800)]
minstrel_ht: fix updating rate with best probability
The throughput should be considered when updating rate
with best probability.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 2 Jul 2010 12:45:22 +0000 (14:45 +0200)]
ath9k: fix crash with WEP in ad-hoc mode
Commit
eed8e22f0133e8278b1f8079fcb452f1f9692f9d added support for using
multicast key lookup to support per-vif/sta keys for AP and ad-hoc.
Unfortunately, it also introduced a crash in ad-hoc mode when the sta
pointer is NULL, which happens when setting up an interface with WEP
keys. This patch fixes it by falling back to the assigned key index.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 1 Jul 2010 22:09:52 +0000 (00:09 +0200)]
ath9k: fix false positives in the baseband hang check
ath9k_hw_check_alive() occasionally returns false, as the hardware
is still processing data in a specific state. Fix this issue by
repeating the test a few times with longer delay inbetween attempts.
This gets rid of excessive hardware resets that appear frequently on
some AR9132 based devices, but could also happen on AR9280.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 1 Jul 2010 22:09:51 +0000 (00:09 +0200)]
ath9k_hw: clean up the noise floor calibration code to reduce code duplication
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 1 Jul 2010 22:09:50 +0000 (00:09 +0200)]
ath9k_hw: sanitize noise floor values properly on all chips
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 1 Jul 2010 22:09:49 +0000 (00:09 +0200)]
ath9k_hw: sync initvals for ar9001 and ar9002 with Atheros
This includes the following changes/fixes:
- a bugfix for stuck beacon issues
- timing changes for improved performance
- AGC setting improvements
- fixes for high temperature issues on some chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 1 Jul 2010 22:09:48 +0000 (00:09 +0200)]
ath9k_hw: reformat the ar5008, ar9001 and ar9002 initvals to match ar9003
This format is generated by the initval tool, available at:
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 1 Jul 2010 22:09:47 +0000 (00:09 +0200)]
ath9k_hw: fix a few inconsistencies in initval array names
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 30 Jun 2010 09:16:31 +0000 (14:46 +0530)]
ath9k_htc: Add LED support for AR7010
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 30 Jun 2010 06:48:42 +0000 (08:48 +0200)]
mac82011: Allow selection of minstrel_ht as default rc algorithm
Allow selection of minstrel_ht as default rate control algorithm. At
the moment minstrel_ht can only be requested by the driver code but
not selected as default in make menuconfig. Fix this by using
minstrel_ht when minstrel was selected as default and minstrel_ht
is available.
This change won't affect legacy devices as minstrel_ht falls back to
minstrel in that case.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 30 Jun 2010 00:07:48 +0000 (02:07 +0200)]
ath9k: fix TSF after reset on AR913x
When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.
Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.
This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 29 Jun 2010 19:49:50 +0000 (21:49 +0200)]
rt2x00: Fix compile warning when debug disabled
CC [M] drivers/net/wireless/rt2x00/rt2800lib.o
drivers/net/wireless/rt2x00/rt2800lib.c: In function 'rt2800_ampdu_action':
drivers/net/wireless/rt2x00/rt2800lib.c:2821: warning: unused variable 'rt2x00dev'
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 29 Jun 2010 19:49:26 +0000 (21:49 +0200)]
rt2x00: Always set BBP_CSR_CFG_BBP_RW_MODE to 1
Latest rt2870 legacy driver also sets BBP_CSR_CFG_BBP_RW_MODE to 1
when reading or writing the EEPROM. This means we can make the
BBP reading and writing completely equal on all platforms.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 29 Jun 2010 19:49:05 +0000 (21:49 +0200)]
rt2x00: Fix antenna initialization
Legacy driver indicates that BBP1_TX_ANTENNA must be set
to 0 for TXPATH values of 1 and 3. So the previous statement
that nothing should be done for TXPATH = 3, is false.
Furthermore, remove the false BBP3_RX_ANTENNA initialization
when TXPATH is 1 for PCI and SOC devices. This field will always
be overridden in the next switch statement, making this initialization
bogus. History of this line indicates it was there from the beginning,
and was once caught as typo. Instead of replacing the line with the
correct line, the correct line was added...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 29 Jun 2010 19:48:37 +0000 (21:48 +0200)]
rt2x00: Fix IEEE80211_HT_CAP_RX_STBC assignment
IEEE80211_HT_CAP_RX_STBC is a 2 bit flag, and should thus
never be set as normal flag. Instead we must read the number
of RX paths from the EEPROM and set the IEEE80211_HT_CAP_RX_STBC
with the correct value (using the same logic as the number of TX
streams).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Tue, 29 Jun 2010 19:48:06 +0000 (21:48 +0200)]
rt2x00: fix beacon reset on rt2800
When an interface is removed the according beacon entry should be reset.
The current approach to only clear the first word is not enough to stop
the device from sending out the beacon, hence resulting in beacons being
sent out for already removed interfaces.
Fix this by invalidating the entire TXWI in front of the beacon instead
of only the first word.
Also clear all beacons during startup in the same way.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Tue, 29 Jun 2010 19:47:37 +0000 (21:47 +0200)]
rt2x00: Disable link tuning in AP mode
Since the link tuning is based on average RSSI values taken from all received
frames it doesn't make sense to enable it in AP mode where every associated
station provides independent RSSI values. Furthermore the legacy drivers
don't enable link tuning in AP mode as well.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Tue, 29 Jun 2010 19:47:10 +0000 (21:47 +0200)]
rt2x00: Fix beacon updates in rt61pci
Fix rt61pci beacon updates in the same way as rt2800pci. rt61pci didn't
update the beacon template after each beacon interval, resulting in the
DTIM count being incorrect (if DTIM period > 1). Fix this by calling
rt2x00lib_beacondone after the current beacon was sent out.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Tue, 29 Jun 2010 19:46:43 +0000 (21:46 +0200)]
rt2x00: Fix beacon updates in rt2800pci
rt2800pci didn't update the beacon template after each beacon interval,
resulting in the DTIM count being incorrect (if DTIM period > 1). Fix this
by calling rt2x00lib_beacondone after the current beacon was sent out.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 29 Jun 2010 19:45:31 +0000 (21:45 +0200)]
rt2x00: Enable multiBSS in rt2800
MAC_BSSID_DW1_BSS_ID_MASK must be set to the mask 3, to
enable 8 BSSID's. The MAC_BSSID_DW1_BSS_BCN_NUM is initialized
to 7 to enable the 8 beacons.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 29 Jun 2010 19:44:50 +0000 (21:44 +0200)]
rt2x00: Align rt2800 EEPROM validation to Ralink vendor driver.
Align with the latest versions of the Ralink legacy driver(s).
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 29 Jun 2010 19:44:18 +0000 (21:44 +0200)]
rt2x00: Correctly detect 93C86 EEPROMs in rt2800pci.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 29 Jun 2010 19:43:44 +0000 (21:43 +0200)]
eeprom_93cx6: Add support for 93c86 EEPROMs.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 29 Jun 2010 19:43:03 +0000 (21:43 +0200)]
rt2x00: Split of TXWI writing to write_tx_data callback in rt2800usb.
Align with the way PCI devices are handled, even though it is not
strictly necessary.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 29 Jun 2010 19:42:23 +0000 (21:42 +0200)]
rt2x00: Rename driver write_tx_datadesc callback function.
Now that the {usb,pci} specific write_tx_data functions are no longer
present we can rename the write_tx_datadesc callback function back to
its old name.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 29 Jun 2010 19:41:40 +0000 (21:41 +0200)]
rt2x00: Move common txdone handling to rt2x00lib_txdone.
Now that the write_tx_data functions are merged, also merge the relevant
parts of the txdone handling into common code, rather than {usb,pci}
specific code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 29 Jun 2010 19:41:05 +0000 (21:41 +0200)]
rt2x00: Merge PCI and USB versions of write_tx_data into single function.
Now that rt2x00pci_write_tx_data and rt2x00usb_write_tx_data are similar
we can merge them in a single function in rt2x00queue.c.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 29 Jun 2010 19:40:34 +0000 (21:40 +0200)]
rt2x00: Move filling of TX URB to rt2x00usb_kick_tx_entry function.
There is no need to fill the TX URB this early, and moving it to the
rt2x00usb_kick_tx_entry function allows us to merge the PCI and USB
variants of the write_tx_data function.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 29 Jun 2010 19:40:02 +0000 (21:40 +0200)]
rt2x00: Fix frame dumping for USB devices.
We forgot to clear the SKBDESC_DESC_IN_SKB when the descriptor was removed
from the front of the skb.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 29 Jun 2010 19:39:29 +0000 (21:39 +0200)]
rt2x00: Remove unneeded variable
The update_bssid is set only when BSS_CHANGED_BSSID is used,
but the check if that field is true is done later in the function
but also only when BSS_CHANGED_BSSID is set. This makes the
variable useless, as it can never result in a negative check.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 29 Jun 2010 19:38:55 +0000 (21:38 +0200)]
rt2x00: Write the BSSID to register when interface is added
For the Master mode case, we initialized the BSSID as the MAC
address, but never wrote it into the registers. This causes
Hardware crypto to break in Master mode when receiving frames
which require the BSSID to be filled in.
This is safe for STA mode since the BSSID will be initialized
to 00:00:00:00:00 at this point, but will be set to the correct
value later when the device associates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Tue, 29 Jun 2010 19:38:12 +0000 (21:38 +0200)]
rt2x00: Implement tx mpdu aggregation
In order to implement tx mpdu aggregation we only have to implement
the ampdu_action callback such that mac80211 allows negotiation of
blockack sessions.
The hardware will handle everything on its own as long as the ampdu
flag in the TXWI struct is set up correctly and we translate the tx
status correctly.
For now, refuse requests to start rx aggregation.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 29 Jun 2010 19:24:05 +0000 (15:24 -0400)]
ath9k: make ath9k_hw_keysetmac static
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 29 Jun 2010 19:20:49 +0000 (15:20 -0400)]
ath9k: remove unused function ath9k_hw_keyisvalid
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 29 Jun 2010 18:51:23 +0000 (14:51 -0400)]
mac80211: add basic tracing to drv_get_survey
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 29 Jun 2010 17:55:04 +0000 (13:55 -0400)]
mac80211: remove unnecessary check in ieee80211_dump_survey
This check is duplicated in drv_get_survey.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 24 Jun 2010 23:44:33 +0000 (01:44 +0200)]
mac80211: fix the for_each_sta_info macro
Because of an ambiguity in the for_each_sta_info macro, it can
currently only be used if the third parameter is set to 'sta'.
Fix this by renaming the parameter to '_sta'.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 24 Jun 2010 23:26:16 +0000 (01:26 +0200)]
ath9k: fix retry count for A-MPDU rate control status reports
The 'bf_retries' field of the ath_buf structure was used for both
software retries (AMPDU subframes) and hardware retries (legacy
frames). This led to a wrong retry count being reported for the A-MPDU
rate control stats.
This patch changes the code to no longer use bf_retries for reporting
retry counts, but instead always using the real on-chip retry count
from the ath_tx_status.
Additionally, if the first subframe of an A-MPDU was not acked, the tx
status report is submitted along with the first acked subframe, which
may not contain the correct rates in the tx info.
This is easily corrected by saving the tx rate info before looping over
subframes, and then copying it back once the A-MPDU status report is
submitted.
In my tests this change improves throughput visibly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Mon, 28 Jun 2010 02:01:48 +0000 (11:01 +0900)]
ath5k: fix antenna div gc for <= AR5K_SREV_PHY_2413
In commit
39d5b2c83ca8904b6826a0713263a4e5a9c0730a "ath5k: update
AR5K_PHY_RESTART_DIV_GC values to match masks" i introduced a regression on PHY
chips older than AR5K_SREV_PHY_5413, which caused signal values to be about
10dB less that before. This patch reverts the AR5K_PHY_RESTART_DIV_GC values to
the same values which were effectively used before (without the bitmask
mistake). This brings signal levels back to normal on these PHY chips.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Magnus Damm [Fri, 25 Jun 2010 09:32:54 +0000 (18:32 +0900)]
b43: Add SDIO_DEVICE() for EW-CG1102GC
This patch enables the EW-CG1102GC SDIO card in the b43 driver.
b43-sdio mmc0:0001:1: Chip ID 14e4:4318
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
b43-phy0 debug: Found PHY: Analog 3, Type 2, Revision 7
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 8
Tested with openfwwf-5.2 using a SuperH SDHI host controller.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 24 Jun 2010 18:38:30 +0000 (14:38 -0400)]
mac80211: use netif_receive_skb in ieee80211_tx_status callpath
This avoids the extra queueing from calling netif_rx.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 24 Jun 2010 18:25:56 +0000 (14:25 -0400)]
mac80211: use netif_receive_skb in ieee80211_rx callpath
This avoids the extra queueing from calling netif_rx.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Mon, 21 Jun 2010 19:15:17 +0000 (12:15 -0700)]
iwlwifi: add disable rf calibration support for 6000g2a and 6000g2b
Radio calibration (chain noise and sensitivity) should be allowed to
be disabled from debugfs if compiled with CONFIG_IWLWIFI_DEBUGFS. For both
6000g2a and 6000g2b, the parameters are missing in "cfg", which cause
user can not disable the radio calibration manually; add the support to
allow the operation.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reinette Chatre [Fri, 18 Jun 2010 23:40:21 +0000 (16:40 -0700)]
iwlagn: reduce severity of disconnected antennas warning
This message is encountered regularly and we need to take a closer look at
the circumstances under which it is printed before presenting errors to
users.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Fri, 18 Jun 2010 18:33:15 +0000 (11:33 -0700)]
iwlwifi: turn on RTS/CTS after aggregation become operational
If RTS/CTS protection is needed for HT, wait until get operational
notification from mac80211, then inform uCode to switch to RTS/CTS
through RXON command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 18 Jun 2010 08:38:56 +0000 (01:38 -0700)]
iwlwifi: read rfkill during resume
When resuming from hibernate or suspend,
the status of the rfkill switch isn't
known since it might have been toggled
while the system was asleep. Therefore,
we need to read out the status at resume
time to make sure the system knows about
an up-to-date status.
Reported-by: Mark Tung <mark.y.tung@intel.com>
Tested-by: Mark Tung <mark.y.tung@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Daniel Halperin [Mon, 14 Jun 2010 20:10:29 +0000 (13:10 -0700)]
iwlwifi: update LQ for bcast station on channel change
The rate table in the bcast LQ is computed only when the station is
allocated, and chooses the lowest rate for the band. Because of when this
occurs, this is the 2.4 GHz band and uses the 0x420a (CCK, 1 Mbps) rate. In 5 GHz
beaconing mode, this rate will prevent beacons from being sent and any other
packets from being received.
We can fix this by re-initializing the bcast station's LQ command when the
channel is changed.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Thu, 17 Jun 2010 22:25:00 +0000 (15:25 -0700)]
iwlwifi: add a mechanism to disable plcp error checking
For some devices, especially the upcoming new devices, the plcp error
rate is different. Before the correct error rate can be determine, also
for the debugging purpose; add the mechanism to disable plcp error checking
which cause radio reset happen.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>